Alexander Kochetkov [Tue, 27 Mar 2018 14:52:27 +0000 (17:52 +0300)]
dm: i2c: implement gpio-based I2C deblock
The commit implement a gpio-based software deblocking. The code
extract I2C pins description from device tree, switch pins to GPIO
mode, toggle SCL until slave release SDA, send I2C stop and switch
I2C pins back to I2C mode.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Alexander Kochetkov [Tue, 27 Mar 2018 14:52:26 +0000 (17:52 +0300)]
dm: i2c: dts: Add gpios and pinctrl device tree properties
The commit describe usage of gpios and pinctrl device tree
properties in order to enable gpio-based software deblocking.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Tom Rini [Mon, 9 Apr 2018 15:06:21 +0000 (11:06 -0400)]
Merge tag 'xilinx-for-v2018.05-rc2' of git://git.denx.de/u-boot-microblaze
Xilinx changes for v2018.05-rc2
- Various DT changes and sync with mainline kernel
- Various defconfig updates
- Add SPL init for zcu102 revA
- Add new zynqmp boards zcu100/zcu104/zcu106/zcu111/zc12XX
and zc1751-dc3
- Net fixes - xlnx,phy-type
- 64bit axi ethernet support
- arasan: Fix nand write issue
- fpga fixes
- Maintainer file updates
Tom Rini [Mon, 9 Apr 2018 15:05:44 +0000 (11:05 -0400)]
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-04-09
Highlights this time around:
- Lots of minor spec compliance fixes
- Support full range of GOP BLT commands
- More fine grained error checking
- Network fixes (init, DP)
- Lots of other bug fixes...
Michal Simek [Wed, 28 Mar 2018 13:55:27 +0000 (15:55 +0200)]
arm64: zynqmp: Add support for Xilinx zcu111-revA
Xilinx zcu111 is a customer board. It is reusing some parts from zcu102.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 28 Mar 2018 13:43:51 +0000 (15:43 +0200)]
arm64: zynqmp: Add support for Xilinx zcu106-revA
Xilinx zcu106 is a customer board. It is reusing some parts from zcu102.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 28 Mar 2018 13:36:36 +0000 (15:36 +0200)]
arm64: zynqmp: Add support for zcu104 customer board
Xilinx zcu104 is another customer board. It is sort of zcu102 clone with
some differences.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 28 Mar 2018 13:09:32 +0000 (15:09 +0200)]
arm64: zynqmp: Add support for zc12xx boards
Add support for zc12xx boards. All of them are internal boards for
silicon validation and share very similar base platforms.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 28 Mar 2018 13:00:25 +0000 (15:00 +0200)]
arm64: zynqmp: Add support for zc1751 dc3
zc1751 is based board with dc3 extenstion card which is used for silicon
validation.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 28 Mar 2018 12:37:47 +0000 (14:37 +0200)]
arm64: zynqmp: Add support for zcu100 aka Ultra96 board
Add support for Xilinx zcu100.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 4 Apr 2018 08:41:35 +0000 (10:41 +0200)]
arm64: zynqmp: Get 200MHz clock early for MMC
SPL MMC boot requires to have clock early.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 4 Apr 2018 08:46:49 +0000 (10:46 +0200)]
arm64: zynqmp: Remove pinctrl settings
This part hasn't been pushed to mainline yet that's why remove it.
The patch can be reverted in future when this is pushed there.
Reported-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Michal Simek [Wed, 4 Apr 2018 08:43:04 +0000 (10:43 +0200)]
arm64: zynqmp: Remove power domain description
This part hasn't been pushed to mainline yet that's why remove it.
The patch can be reverted in future when this is pushed there.
Reported-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Michal Simek [Wed, 28 Mar 2018 12:49:43 +0000 (14:49 +0200)]
arm64: zynqmp: Add low level initialization for zc1751
Add psu init for zc1751 dc cards.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 28 Mar 2018 12:47:16 +0000 (14:47 +0200)]
arm64: zynqmp: Add low level initialization for zcu102-revA
Add psu init for zcu102-revA.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 28 Mar 2018 12:18:19 +0000 (14:18 +0200)]
arm64: zynqmp: Enable Fixed link support
This patch enables the fixed link support for
all ZynqMP boards.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 28 Mar 2018 12:30:35 +0000 (14:30 +0200)]
arm64: zynqmp: Enable mac address randomization for zc1751 dc5
There is no memory which stores mac address that's why generate it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 28 Mar 2018 12:17:19 +0000 (14:17 +0200)]
arm64: zynqmp: Enable ethernet phys for zc1751 dc5
Enable ethernet phys for zc1751 dc5.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Luca Ceresoli [Mon, 12 Mar 2018 16:18:38 +0000 (17:18 +0100)]
arm64: zynqmp: Enable booting to ATF
U-Boot is now able to boot to ARM Trusted Firmware (ATF). The boot
flow is SPL(EL3) loads ATF and full u-boot and jump to ATF(EL3) which
pass control to full u-boot(EL2). This has been tested on zcu106, so
enable it in this defconfig.
To generate an image that triggers this booting flow, you need to pass
'-O arm-trusted-firmware' to mkimage.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 28 Mar 2018 13:20:48 +0000 (15:20 +0200)]
arm64: zynqmp: Enable pxe and dhcp if commands are enabled
Targets without net can't use pxe or dhcp boot methods.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Siva Durga Prasad Paladugu [Fri, 12 Jan 2018 07:14:54 +0000 (12:44 +0530)]
net: phy: xilinx_phy: Read phytype using property xlnx,phy-type
This patch reads phytype from property "xlnx,phy-type" instead
od simply looking for "phy-type". This is to be inline with
Linux and also fixes the issue of detecting it wrongly in
u-boot.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Vipul Kumar [Tue, 23 Jan 2018 09:22:35 +0000 (14:52 +0530)]
axi: ethernet: Added support for 64 bit addressing for axi-ethernet
This patch uses writeq() function to enable greater than 32 bit
addressing of axi-ethernet for the ZynqMP devices.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Vipul Kumar [Sat, 10 Mar 2018 12:22:23 +0000 (17:52 +0530)]
nand: arasan_nfc: Fixed NAND write issue
In commit
2453c695185f ("arm64: zynqmp: nand: Fixed NAND erase issue for
size 1GiB or more"), ARASAN_NAND_MEM_ADDR1_PAGE_MASK macro changed
to 0xFFFF and the same macro is used in nand write and so that getting
nand write error.
This patch reverted this macro to the 0xFFFF0000 and used
ARASAN_NAND_MEM_ADDR1_COL_MASK in the nand erase function
which is equal to 0xFFFF.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Siva Durga Prasad Paladugu [Tue, 6 Mar 2018 12:07:09 +0000 (17:37 +0530)]
fpga: zynq: Add delay after PCFG_PROG_B change
There is delay needed after PCFG_PROGB change if
AES key source is efuse. This fixes the issue of
encrypted bitstream loading with AES efuse as key
source.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Siva Durga Prasad Paladugu [Wed, 14 Mar 2018 18:47:24 +0000 (00:17 +0530)]
fpga: zynqmp: Fix the nonsecure bitstream loading issue
Xilfpga library expects the size of bitstream in a pointer
but currenly we are passing the size as a value. This patch
fixes this issue.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Siva Durga Prasad Paladugu [Thu, 1 Mar 2018 12:14:47 +0000 (17:44 +0530)]
fpga: zynqmp: Update zynqmp_load() as per latest xilfpga
Latest xilfpga expects to set BIT5 of flags for nonsecure
bitsream and also expects length in bytes instead of words
This patch does the same.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Nitin Jain [Fri, 16 Feb 2018 11:59:54 +0000 (17:29 +0530)]
fpga: zynqmp: Add support to get the PCAP status for fpga info command
This patch adds support for ZynqMP platform to print FPGA PCAP status
for "fpga status" command.
Signed-off-by: Nitin Jain <nitinj@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 21 Feb 2018 12:59:21 +0000 (13:59 +0100)]
clk: zynqmp: Add new compatible string for clock driver
New and old clk drivers are sharing IDs and descriptions.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 27 Mar 2018 11:49:05 +0000 (13:49 +0200)]
arm: zynq: Use fixed partitions for spi flash for zc770 xm010
Sync with mainline.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 27 Mar 2018 11:48:51 +0000 (13:48 +0200)]
arm: zynq: Fix eeprom dt nodes
- Use eeprom for node name
- Use atmel compatible string instead of at.
- Add missing labels
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Javier Martinez Canillas [Thu, 15 Jun 2017 18:54:12 +0000 (20:54 +0200)]
ARM: dts: zynq: Add generic compatible string for I2C EEPROM
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 6 Feb 2018 13:00:30 +0000 (14:00 +0100)]
arm: zynq: Use i2c-mux instead of i2cswitch for pca9548
i2c muxes should described like this.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 27 Mar 2018 11:43:05 +0000 (13:43 +0200)]
arm: zynq: Sync up licenses with mainline kernel
Use different location for SPDX line. Also update dates for new mainline
DTS files.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 27 Mar 2018 12:31:42 +0000 (14:31 +0200)]
arm: zynq: Remove 0x prefixes from cc108
The patch fixing issues reported by DTC:
zynq-cc108.dtb: Warning (unit_address_format): Node
/amba/spi@
e000d000/flash@0/partition@0x400000 unit name should not have
leading "0x"
zynq-cc108.dtb: Warning (unit_address_format): Node
/amba/spi@
e000d000/flash@0/partition@0x800000 unit name should not have
leading "0x"
zynq-cc108.dtb: Warning (unit_address_format): Node
/amba/spi@
e000d000/flash@0/partition@0xc00000 unit name should not have
leading "0x"
zynq-cc108.dtb: Warning (unit_address_format): Node
/amba/spi@
e000d000/flash@0/partition@0xd00000 unit name should not have
leading "0x"
zynq-cc108.dtb: Warning (unit_address_format): Node
/amba/spi@
e000d000/flash@0/partition@0xf00000 unit name should not have
leading "0x"
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 27 Mar 2018 14:21:42 +0000 (16:21 +0200)]
arm64: zynqmp: Remove double spaces from dts file
There is no reason to have double spaces for indentation.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 27 Mar 2018 10:48:30 +0000 (12:48 +0200)]
arm64: zynqmp: Add silabs prefix to u69 for zcu102
Add vendor prefix to si5341.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 27 Mar 2018 08:39:53 +0000 (10:39 +0200)]
arm64: zynqmp: Remove number from clock-generator node name
There shouldn't be a number appended based on spec.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 27 Mar 2018 08:47:26 +0000 (10:47 +0200)]
arm64: zynqmp: Remove u-boot commands from dts files
U-Boot commands shouldn't be the part of kernel DTS files.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Srinivas Goud [Tue, 22 Aug 2017 09:08:46 +0000 (14:38 +0530)]
arm64: zynqmp: Update sd properties for dc5
This patch adds no-1-8-v below properties to sd node for dc5 board dts.
Signed-off-by: Srinivas Goud <srinivas.goud@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 27 Mar 2018 14:10:25 +0000 (16:10 +0200)]
arm64: zynqmp: Enable ttcs for zc1751 dc5
Enable TTCs for this target as is done in Linux kernel.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 27 Mar 2018 11:15:17 +0000 (13:15 +0200)]
arm64: zynqmp: Add eeprom reference to eeprom nodes
eeprom can contain information which can be used by nvmem drivers.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 27 Mar 2018 08:54:25 +0000 (10:54 +0200)]
arm64: zynqmp: Use atmel prefix instead of at
This changes was done in mainline and this patch is just following it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 27 Mar 2018 11:09:15 +0000 (13:09 +0200)]
arm64: zynqmp: Fix spi flash partition definition for zc1751 dc2
Using different node name and label partitions as data.
Also use latest compatible strings based on mainline review.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 27 Mar 2018 10:50:04 +0000 (12:50 +0200)]
arm64: zynqmp: Use s/_/-/g in node name for zcu102 rev1.0
Follow spec for node names.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 27 Mar 2018 10:13:13 +0000 (12:13 +0200)]
arm64: zynqmp: Use keycode from input/input.h
Instead of hardcoding numbers.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 27 Mar 2018 10:01:24 +0000 (12:01 +0200)]
arm64: zynqmp: Remove additional comments from dts files
Remove additional comments which were removed as the part of upstreaming.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 27 Mar 2018 08:36:39 +0000 (10:36 +0200)]
arm64: zynqmp: Sync up license with mainline kernel
Mainline Linux kernel has adopted SPDX header license in a different
format then was used before. This patch is syncing it up.
Also update years in License text and remove Nathalie's email because it
is no longer valid.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 27 Mar 2018 08:38:08 +0000 (10:38 +0200)]
arm64: zynqmp: Use i2c-mux instead of i2cswitch instead
Based on review from mainline i2c-mux is standard name for i2c switches.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 27 Mar 2018 08:52:40 +0000 (10:52 +0200)]
arm64: zynqmp: Use maxim prefix for all maxim chips
Use vendor prefix for Maxim chips.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 17 Jan 2018 15:32:33 +0000 (16:32 +0100)]
arm64: zynqmp: Sync alignment with mainline
Sync pcie and lpd_dma nodes with mainline version.
Incorrect locations are causing diff in statistics that's why
synchronizations are needed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Heinrich Schuchardt [Fri, 6 Apr 2018 13:36:31 +0000 (15:36 +0200)]
efi_loader: correctly set the machine type in the PE header
The portable executable header has a field describing the machine type.
The machine type should match the binary. So on i386 we should use
IMAGE_FILE_MACHINE_I386 and on x86_64 we should use
IMAGE_FILE_MACHINE_AMD64. The actual value is issued by the objcopy
command invoked in scripts/Makefile.lib in depdendence of the value of
EFI_TARGET.
The value is used both for EFI_STUB and for EFI_LOADER.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Heinrich Schuchardt [Wed, 4 Apr 2018 07:22:03 +0000 (09:22 +0200)]
MAINTAINERS: ZYNQMP: correct entries
Replace references to non-existent file.
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 13 Mar 2018 10:50:22 +0000 (11:50 +0100)]
MAINTAINERS: Fix zynqmp clock driver path
Fix c&p error from Zynq.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 23 Feb 2018 12:39:37 +0000 (13:39 +0100)]
arm: zynq: Handle ENXIO error return value properly
zynq_clk_get_rate() is also returning ENXIO which is not handled now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Anton Gerasimov [Sat, 24 Mar 2018 17:32:00 +0000 (18:32 +0100)]
ARM: dts: zynq: Rename dts for Z-turn board
Makes naming in line with other Zynq boards.
Signed-off-by: Anton Gerasimov <tossel@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Anton Gerasimov [Sat, 24 Mar 2018 17:31:59 +0000 (18:31 +0100)]
ARM: dts: zynq: Update dts for Z-turn board
Delete devices implemented in PL, stylistic changes.
Signed-off-by: Anton Gerasimov <tossel@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Alex Kiernan [Sun, 1 Apr 2018 16:37:54 +0000 (16:37 +0000)]
Cleanup CONFIG_VERSION_VARIABLE migration
CONFIG_VERSION_VARIABLE had already been mostly migrated to Kconfig,
but two headers still referenced it. Also set defaults so that
most of the defconfigs inherit the default rather than needing it
to be set explicitly.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Petr Vorel <petr.vorel@gmail.com>
Alex Kiernan [Sun, 1 Apr 2018 16:37:53 +0000 (16:37 +0000)]
Migrate CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to Kconfig
Convert CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to Kconfig
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Petr Vorel <petr.vorel@gmail.com>
Reviewed-by: Petr Vorel <petr.vorel at gmail.com>
Alex Kiernan [Sun, 1 Apr 2018 09:22:38 +0000 (09:22 +0000)]
net: Move enetaddr env access code to env config instead of net config
In order that we can use eth_env_* even when CONFIG_NET isn't set, move
these functions to environment code from net code.
This fixes failures such as:
board/ti/am335x/built-in.o: In function `board_late_init':
board/ti/am335x/board.c:752: undefined reference to `eth_env_set_enetaddr'
u-boot/board/ti/am335x/board.c:766: undefined reference to `eth_env_set_enetaddr'
which caters for use cases such as:
commit
f411b5cca48f ("board: am335x: Always set eth/eth1addr environment
variable")
when Ethernet is required in Linux, but not U-Boot.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Alex Kiernan [Sun, 1 Apr 2018 09:22:37 +0000 (09:22 +0000)]
ti: am335x: Fix build when networking is disabled
When compiling without CONFIG_CLOCK_SYNTHESIZER (which is implied by
CONFIG_DRIVER_TI_CPSW for am335x_evm), exclude the network setup for
AM335x-ICEv2 to avoid link time failures:
board/ti/am335x/board.c:683: undefined reference to `setup_clock_synthesizer'
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Alex Kiernan [Sun, 1 Apr 2018 09:22:36 +0000 (09:22 +0000)]
usb: gadget: USB_ETHER requires network support
In order to compile the USB Ethernet gadget support we require that NET
is enabled, add that dependency here.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Alex Kiernan [Sun, 1 Apr 2018 09:22:35 +0000 (09:22 +0000)]
ti: am335x: Fix bootargs when building without NET
If DHCP/PXE commands are disabled then the compilation fails due to
bootargs attempting to use them:
include/config_distro_bootcmd.h:319:2: error: expected ‘}’ before ‘BOOT_TARGET_DEVICES_references_PXE_without_CONFIG_CMD_DHCP_or_PXE’
Ensure that if the command aren't enabled, we don't try and use them.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Alex Kiernan [Sun, 1 Apr 2018 09:22:34 +0000 (09:22 +0000)]
Migrate CONFIG_DRIVER_TI_CPSW to Kconfig
This converts CONFIG_DRIVER_TI_CPSW to Kconfig
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Mario Six [Wed, 28 Mar 2018 12:38:20 +0000 (14:38 +0200)]
treewide: Convert CONFIG_HOSTNAME to a string option
CONFIG_HOSTNAME is defined as a "plain" preprocessor string, but every
use is couched by __stringify(...).
Hence, convert it to a proper string option.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Mario Six [Wed, 28 Mar 2018 12:38:19 +0000 (14:38 +0200)]
treewide: Migrate CONFIG_FSL_ESDHC to Kconfig
Migrate the CONFIG_FSL_ESDHC option to Kconfig.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Mario Six [Wed, 28 Mar 2018 12:38:18 +0000 (14:38 +0200)]
treewide: Migrate CONFIG_TSEC_ENET to Kconfig
Migrate the CONFIG_TSEC_ENET option to Kconfig.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Mario Six [Wed, 28 Mar 2018 12:38:17 +0000 (14:38 +0200)]
treewide: Migrate CONFIG_DISPLAY_BOARDINFO_LATE to Kconfig
Migrate the CONFIG_DISPLAY_BOARDINFO_LATE option to Kconfig.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
Mario Six [Wed, 28 Mar 2018 12:38:16 +0000 (14:38 +0200)]
treewide: Migrate CONFIG_LAST_STAGE_INIT to Kconfig
Migrate the CONFIG_LAST_STAGE_INIT option to Kconfig.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Mario Six [Wed, 28 Mar 2018 12:38:15 +0000 (14:38 +0200)]
treewide: Migrate CONFIG_BOARD_EARLY_INIT_R to Kconfig
Migrate the CONFIG_BOARD_EARLY_INIT_R option to Kconfig.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Mario Six [Wed, 28 Mar 2018 12:38:14 +0000 (14:38 +0200)]
treewide: Migrate CONFIG_SYS_ALT_MEMTEST to Kconfig
Migrate the CONFIG_SYS_ALT_MEMTEST option to Kconfig.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
[trini: Re-run migration after also including CMD_MEMTEST]
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Sun, 8 Apr 2018 00:27:54 +0000 (20:27 -0400)]
configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Sat, 7 Apr 2018 17:11:01 +0000 (13:11 -0400)]
configs: Finish migration of CONFIG_ATMEL_SPI
With the previous temporary reverts, we need to re-complete the
migration of CONFIG_ATMEL_SPI here now.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Sat, 7 Apr 2018 13:15:50 +0000 (09:15 -0400)]
Revert "spi: atmel: Drop non-dm code"
As we aren't quite able to convert some platforms with a very small size
limit in SPL yet, we need to revert this for now.
This reverts commit
7b0947787358c6b277431d6b76ce043d8bec641d.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Sat, 7 Apr 2018 13:15:06 +0000 (09:15 -0400)]
Revert "spi: atmel: Drop atmel_spi.h"
As we aren't quite able to convert some platforms with a very small size
limit in SPL yet, we need to revert this for now.
This reverts commit
37434db29be495ef41f204a97b8bf13b1418f97d.
Signed-off-by: Tom Rini <trini@konsulko.com>
Mario Six [Wed, 28 Mar 2018 12:39:18 +0000 (14:39 +0200)]
cmd: Add command for calculating binary operations
This patch adds a command that enables the calculation of bit operations
(AND, OR, XOR) on binary data from the command line. Memory locations as
well as the contents of environment variables are eligible as sources
and destination of the binary data used in the operations.
The possible applications are manifold: Setting specific bits in
registers using the regular read-OR-write pattern, masking out bits in
bit values, implementation of simple OTP encryption using the XOR
operation, etc.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Mario Six [Wed, 28 Mar 2018 12:39:10 +0000 (14:39 +0200)]
cmd: ximg: Respect cache line size for flushing
Make sure that the cache line size if respected when flushing the cache.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Mario Six [Wed, 28 Mar 2018 12:39:01 +0000 (14:39 +0200)]
gpio: uclass: Fix debug string
A debug string still has the old name of a function being called; update
it.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Michal Simek [Wed, 28 Mar 2018 10:57:54 +0000 (12:57 +0200)]
watchdog: Fix Kconfig alignment for WDT_SANDBOX
Fix Kconfig alignment which should be <tab><space><space>.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Michal Simek [Mon, 26 Mar 2018 14:31:27 +0000 (16:31 +0200)]
image: fit: Show information about OS type in firwmare case too
SPL ATF implementation requires FIT image with partitions where the one
is Firmware/ATF and another one Firmware/U-Boot. OS field is used for
recording that difference that's why make sense to show values there for
Firmware types.
For example:
Image 0 (atf)
Description: ATF bl31.bin
Created: Mon Mar 26 15:58:14 2018
Type: Firmware
Compression: uncompressed
Data Size: 51152 Bytes = 49.95 KiB = 0.05 MiB
Architecture: ARM
OS: ARM Trusted Firmware
Load Address: 0xfffe0000
Hash algo: md5
Hash value:
36a4212bbb698126bf5a248f0f4b5336
Image 1 (uboot)
Description: u-boot.bin
Created: Mon Mar 26 15:58:14 2018
Type: Firmware
Compression: uncompressed
Data Size: 761216 Bytes = 743.38 KiB = 0.73 MiB
Architecture: ARM
OS: U-Boot
Load Address: 0x08000000
Hash algo: md5
Hash value:
f22960fe429be72296dc8dc59a47d566
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Michal Simek [Mon, 26 Mar 2018 14:31:26 +0000 (16:31 +0200)]
image: fit: Show firmware configuration property if present
SPL ATF support requires to have firmware property which should be also
listed by mkimage -l when images is created.
The patch is also using this macro in spl_fit to match keyword.
When image is created:
Default Configuration: 'config'
Configuration 0 (config)
Description: ATF with full u-boot
Kernel: unavailable
Firmware: atf
FDT: dtb
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Vignesh R [Mon, 26 Mar 2018 07:57:03 +0000 (13:27 +0530)]
configs: am43xx_evm_qspiboot_defconfig: Move to DM
Move am43xx_evm_qspiboot_defconfig to DM. This is required as SPI core
and TI QSPI driver no longer supports non DM interfaces.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Vignesh R [Mon, 26 Mar 2018 07:57:02 +0000 (13:27 +0530)]
ARM: dts: Add new "generic" am4372 device tree file.
With U-boot runtime board detect for DTB selection a "default" dtb needs
to be created. This will be used temporarily until the "proper" dtb is
selected.
Also, add -u-boot.dtsi for AM437x SK and IDK to enable I2C for
board detection via DM_I2C.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Vignesh R [Mon, 26 Mar 2018 07:57:01 +0000 (13:27 +0530)]
board: ti: am43xx: Define embedded_dtb_select for runtime DTB selection in U-boot
AM437x QSPI boot is a single stage boot and hence needs runtime DTB
selection to support AM437x-SK and AM437x-IDK with DM enabled. This is
required to move am43xx_evm_qspiboot_defconfig to use DM/DT.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Sjoerd Simons [Thu, 22 Mar 2018 21:53:50 +0000 (22:53 +0100)]
env: Properly check for BLK support
Use CONFIG_IS_ENABLED to see if CONFIG_BLK is enabled. Otherwise
SPL compilation breaks on boards which do have CONFIG_BLK enabled but
not DM_MMC for the SPL as follows:
env/mmc.c: In function ‘init_mmc_for_env’:
env/mmc.c:164:6: warning: implicit declaration of function ‘blk_get_from_parent’; did you mean ‘efi_get_ram_base’? [-Wimplicit-function-declaration]
if (blk_get_from_parent(mmc->dev, &dev))
^~~~~~~~~~~~~~~~~~~
efi_get_ram_base
env/mmc.c:164:29: error: ‘struct mmc’ has no member named ‘dev’
if (blk_get_from_parent(mmc->dev, &dev))
^~
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Andrew F. Davis [Thu, 22 Mar 2018 20:44:40 +0000 (15:44 -0500)]
configs: k2hk_hs_evm: Resync defconfig with non-HS defconfig
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh vutla <lokeshvutla@ti.com>
Andrew F. Davis [Thu, 22 Mar 2018 20:44:39 +0000 (15:44 -0500)]
configs: k2e_hs_evm: Resync defconfig with non-HS defconfig
Signed-off-by: Andrew F. Davis <afd@ti.com>
Andrew F. Davis [Thu, 22 Mar 2018 20:44:38 +0000 (15:44 -0500)]
configs: k2g_hs_evm: Resync defconfig with non-HS defconfig
Signed-off-by: Andrew F. Davis <afd@ti.com>
Chris Packham [Wed, 21 Mar 2018 02:40:37 +0000 (15:40 +1300)]
rtc: rx8025: remove redundant code in rtc_reset
As of commit
1a1fa2406689 ("rtc: Set valid date after reset") the
command "date reset" will set the date/time to 2000-01-01 0:00:00 after
calling rtc_reset(). This means that the rx8025 implementation of
rtc_reset() does not need to call rtc_set().
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Chris Packham [Wed, 21 Mar 2018 02:40:36 +0000 (15:40 +1300)]
rtc: rs5c372: remove redundant code in rtc_reset
As of commit
1a1fa2406689 ("rtc: Set valid date after reset") the
command "date reset" will set the date/time to 2000-01-01 0:00:00 after
calling rtc_reset(). This means that the rs5c372 implementation of
rtc_reset() does not need to call rtc_set().
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Chris Packham [Wed, 21 Mar 2018 02:40:35 +0000 (15:40 +1300)]
rtc: mx27rtc: remove redundant code in rtc_reset
As of commit
1a1fa2406689 ("rtc: Set valid date after reset") the
command "date reset" will set the date/time to 2000-01-01 0:00:00 after
calling rtc_reset(). This means that the mx27rtc implementation of
rtc_reset() can be an empty stub function.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Chris Packham [Wed, 21 Mar 2018 02:40:34 +0000 (15:40 +1300)]
rtc: ds1374: remove redundant code in rtc_reset
As of commit
1a1fa2406689 ("rtc: Set valid date after reset") the
command "date reset" will set the date/time to 2000-01-01 0:00:00 after
calling rtc_reset(). This means that the ds1374 implementation of
rtc_reset() doesn't need to call rtc_set().
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Chris Packham [Wed, 21 Mar 2018 02:40:33 +0000 (15:40 +1300)]
rtc: ds1307: remove redundant code in rtc_reset
As of commit
1a1fa2406689 ("rtc: Set valid date after reset") the
command "date reset" will set the date/time to 2000-01-01 0:00:00 after
calling rtc_reset(). This means that the ds1307 implementation of
rtc_reset() doesn't need to call rtc_set().
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Christian Gmeiner [Tue, 20 Mar 2018 13:18:25 +0000 (14:18 +0100)]
bootvx: use program header for loading
The section header address is a VMA whereas the address found in
the program header is a physical one. With this change it is
possible to load and start a vx7 intel generic based image.
$ readelf -l /tmp/vx7
Elf file type is EXEC (Executable file)
Entry point 0x408000
There are 2 program headers, starting at offset 52
Program Headers:
Type Offset VirtAddr PhysAddr FileSiz MemSiz Flg Align
LOAD 0x001000 0x00408000 0x00408000 0x04000 0x04000 RWE 0x1000
LOAD 0x005000 0xe040c000 0x0040c000 0x583a84 0x5ccc70 RWE 0x1000
Section to Segment mapping:
Segment Sections...
00 .text.locore .data.locore
01 .text .eh_frame .wrs_build_vars .data .tls_data .tls_vars .bss
$ readelf -S /tmp/vx7
There are 13 section headers, starting at offset 0x588af8:
Section Headers:
[Nr] Name Type Addr Off Size ES Flg Lk Inf Al
[ 0] NULL
00000000 000000 000000 00 0 0 0
[ 1] .text.locore PROGBITS
00408000 001000 00011e 00 AX 0 0 16
[ 2] .data.locore PROGBITS
00409000 002000 003000 00 WA 0 0 4096
[ 3] .text PROGBITS
e040c000 005000 4802a0 00 WAX 0 0 32
[ 4] .eh_frame PROGBITS
e088c2a0 4852a0 0a1ed0 00 A 0 0 4
[ 5] .wrs_build_vars PROGBITS
e092e170 527170 000190 00 Ax 0 0 1
[ 6] .data PROGBITS
e092f000 528000 060a70 00 WA 0 0 4096
[ 7] .tls_data PROGBITS
e098fa70 588a70 000004 00 A 0 0 4
[ 8] .tls_vars PROGBITS
e098fa78 588a78 00000c 00 WA 0 0 4
[ 9] .bss NOBITS
e098faa0 588a84 0491d0 00 WA 0 0 32
[10] .shstrtab STRTAB
00000000 588a84 000074 00 0 0 1
[11] .symtab SYMTAB
00000000 588d00 056ee0 10 12 9758 4
[12] .strtab STRTAB
00000000 5dfbe0 05f48a 00 0 0 1
Key to Flags:
W (write), A (alloc), X (execute), M (merge), S (strings)
I (info), L (link order), G (group), T (TLS), E (exclude), x (unknown)
O (extra OS processing required) o (OS specific), p (processor specific)
For completeness here are the same information for an old vx5 based image. After
this change it is possible to boot vx5 and vx7 (intel generic) images.
$ readelf -l /tmp/vx5
Elf file type is EXEC (Executable file)
Entry point 0x308000
There are 1 program headers, starting at offset 52
Program Headers:
Type Offset VirtAddr PhysAddr FileSiz MemSiz Flg Align
LOAD 0x000060 0x00308000 0x00308000 0x3513a0 0x757860 RWE 0x20
Section to Segment mapping:
Segment Sections...
00 .text .data .bss
[christian@chgm-pc ~]$ readelf -S /tmp/vx5
There are 12 section headers, starting at offset 0x356580:
Section Headers:
[Nr] Name Type Addr Off Size ES Flg Lk Inf Al
[ 0] NULL
00000000 000000 000000 00 0 0 0
[ 1] .text PROGBITS
00308000 000060 319b10 00 WAX 0 0 32
[ 2] .data PROGBITS
00621b20 319b80 037880 00 WA 0 0 32
[ 3] .bss NOBITS
006593a0 351400 4064c0 00 WA 0 0 16
[ 4] .debug_aranges PROGBITS
00000000 351400 000060 00 0 0 1
[ 5] .debug_pubnames PROGBITS
00000000 351460 00018b 00 0 0 1
[ 6] .debug_info PROGBITS
00000000 3515eb 003429 00 0 0 1
[ 7] .debug_abbrev PROGBITS
00000000 354a14 000454 00 0 0 1
[ 8] .debug_line PROGBITS
00000000 354e68 0016a4 00 0 0 1
[ 9] .shstrtab STRTAB
00000000 35650c 000071 00 0 0 1
[10] .symtab SYMTAB
00000000 356760 0440e0 10 11 8574 4
[11] .strtab STRTAB
00000000 39a840 03e66c 00 0 0 1
Key to Flags:
W (write), A (alloc), X (execute), M (merge), S (strings)
I (info), L (link order), G (group), T (TLS), E (exclude), x (unknown)
O (extra OS processing required) o (OS specific), p (processor specific)
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Patrick Delaunay [Tue, 20 Mar 2018 13:15:06 +0000 (14:15 +0100)]
stm32mp: handle SYSRESET
Add support of sysreset with generic driver "syscon-reboot"
provided by RCC, for U-boot and for SPL.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrick Delaunay [Tue, 20 Mar 2018 10:45:14 +0000 (11:45 +0100)]
stm32mp: add syscon for STGEN
Add STGEN as SYSCON device: allow access to device address
defined in device tree
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrick Delaunay [Tue, 20 Mar 2018 10:41:26 +0000 (11:41 +0100)]
stm32mp1: change STGEN clock source to HSE
No more use static frequency HSI = 64MHz for STGEN clock
but HSE (with higher accurency) by default.
Need to remove CONFIG_SYS_HZ_CLOCK as arch timer frequency
is provided at boot by BootRom and cp15 cntfrq and modified
during clock tree initialization if needed.
When HSI is no more used by any device, this internal
oscillator can be switched off to reduce consumption.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrick Delaunay [Tue, 20 Mar 2018 10:41:25 +0000 (11:41 +0100)]
clock: stm32mp1: add stgen clock source change support
The STGEN is the clock source for the Cortex A7 arch timer.
So after modification of its frequency, CP15 cntfreq is updated
and a new timer init is performed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrick Delaunay [Tue, 20 Mar 2018 10:41:23 +0000 (11:41 +0100)]
arm: timer: get frequency for arch timer armv7 in cp15 cntfrq
Manage dynamic value for armv7 arch clock timer,
when CONFIG_SYS_HZ_CLOCK is not defined.
Get frequency from CP15 cntfrq information, initialized for example
by first boot stage, clock driver or by BootRom.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Rasmus Villemoes [Tue, 20 Mar 2018 10:38:45 +0000 (11:38 +0100)]
Allow providing default environment from file
Modifying the default environment via CONFIG_EXTRA_ENV_SETTINGS is
somewhat inflexible, partly because the cpp language does not allow
appending to an existing macro. This prevents reuse of "environment
fragments" for different boards, which in turn makes maintaining that
environment consistently tedious and error-prone.
This implements a Kconfig option for allowing one to define the entire
default environment in an external file, which can then, for example, be
generated programmatically as part of a Yocto recipe, or simply be kept
in version control separately from the U-boot repository.
Tested-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Patrick Delaunay [Tue, 20 Mar 2018 09:54:54 +0000 (10:54 +0100)]
stm32mp1: select boot device and partition
Bootrom loads SPL from SDCARD or eMMC
according BootPin selection.
Then SPL loads U-Boot on the same mmc device
with the following predefined GPT partitioning:
on SDCARD: gpt partitioning
1: SPL
2: SPL#2
3: U-Boot
4: bootable partition
on eMMC:
The 2 boot partitions are used for SPL (2 copy)
boot1: SPL
boot2: SPL#2
The user partition use gpt partitioning
1: U-Boot
2: bootable partition
This patch select the correct SPL partition
(3 for SDCARD on mmc0 and 1 for eMMC on mmc1)
according the BootRom information saved in TAMP register
and based on configuration flasg:
- CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION
=> for BOOT_DEVICE_MMC1 or mmc 0 in U-Boot
- CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION_MMC2 (new)
=> for BOOT_DEVICE_MMC2 or mmc 1 in U-Boot
And the correct boot_targets is selected according the environment
variables boot_device and boot_instance, with preboot command,
to search the bootable partition with kernel on this device
(generic distro support).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>