media: ov5640: Adjust the clock based on the expected rate

The clock structure for the PCLK is quite obscure in the documentation, and
was hardcoded through the bytes array of each and every mode.

This is troublesome, since we cannot adjust it at runtime based on other
parameters (such as the number of bytes per pixel), and we can't support
either framerates that have not been used by the various vendors, since we
don't have the needed initialization sequence.

We can however understand how the clock tree works, and then implement some
functions to derive the various parameters from a given rate. And now that
those parameters are calculated at runtime, we can remove them from the
initialization sequence.

The modes also gained a new parameter which is the clock that they are
running at, from the register writes they were doing, so for now the switch
to the new algorithm should be transparent.

Co-Developed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Tested-by: Adam Ford <aford173@gmail.com> #imx6dq
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: ov5640: Fix set format regression

The set_fmt operations updates the sensor format only when the image format
is changed. When only the image sizes gets changed, the format do not get
updated causing the sensor to always report the one that was previously in
use.

Without this patch, updating frame size only fails:
  [fmt:UYVY8_2X8/640x480@1/30 field:none colorspace:srgb xfer:srgb ...]

With this patch applied:
  [fmt:UYVY8_2X8/1024x768@1/30 field:none colorspace:srgb xfer:srgb ...]

Fixes: 6949d864776e ("media: ov5640: do not change mode if format or frame interval is unchanged")

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx6 w/ CSI2 interface on 4.19.6 and 4.20-RC5
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: mt9m111: allow to setup pixclk polarity

The chip can be configured to output data transitions on the
rising or falling edge of PIXCLK (Datasheet R58:1[9]), default is on the
falling edge.

Parsing the fw-node is made in a subfunction to bundle all (future)
dt-parsing / fw-parsing stuff.

[m.grzeschik@pengutronix.de: Fix inverting clock. INV_PIX_CLOCK bit is set
 per default. Set bit to 0 (enable mask bit without value) to enable
 falling edge sampling.]
[m.felsch@pengutronix.de: use fwnode helpers]
[m.felsch@pengutronix.de: mv fw parsing into own function]
[m.felsch@pengutronix.de: adapt commit msg]
[sakari.ailus@linux.intel.com: V4L2 API usage changes to compile
 on media tree master]

Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dt-bindings: media: mt9m111: add pclk-sample property

Add the pclk-sample property to the list of optional properties
for the mt9m111 camera sensor.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dt-bindings: media: mt9m111: adapt documentation to be more clear

Replace the vague binding by a more verbose. Remove the remote property
from the example since the driver don't support such a property. Also
remove the bus-width property from the endpoint since the driver don't
take care of it.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: mt9m111: add support to select formats and fps for {Q,SXGA}

This patch implements the framerate selection using the skipping and
readout power-modi features. The power-modi cut the framerate by half
and each context has an independent selection bit. The same applies to
the 2x skipping feature.

Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: mt9m111: add streaming check to set_fmt

Currently set_fmt don't care about the streaming status, so the format
can be changed during streaming. This can lead into wrong behaviours.

Check if the device is already streaming and return -EBUSY to avoid
wrong behaviours.

Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: mt9m111: add s_stream callback

Add callback to check if we are already streaming. Now other callbacks
can check the state and return -EBUSY if we already streaming.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: imx274: select REGMAP_I2C

The imx274 driver uses regmap and the build will fail without it.

Fixes:

  drivers/media/i2c/imx274.c:142:21: error: variable ‘imx274_regmap_config’ has initializer but incomplete type
   static const struct regmap_config imx274_regmap_config = {
                       ^~~~~~~~~~~~~
  drivers/media/i2c/imx274.c:1869:19: error: implicit declaration of function ‘devm_regmap_init_i2c’ [-Werror=implicit-function-declaration]
    imx274->regmap = devm_regmap_init_i2c(client, &imx274_regmap_config);
                     ^~~~~~~~~~~~~~~~~~~~

and others.

Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: imx274: declare the correct number of controls

v4l2_ctrl_handler_init() expects a hint of how many controls this
handler is expected to refer to. Since this number here is always 4,
let's pass exactly 4.

Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: imx274: fix stack corruption in imx274_read_reg

imx274_read_reg() takes a u8 pointer ("reg") and casts it to pass it
to regmap_read(), which takes an unsigned int pointer. This results in
a corrupted stack and random crashes.

Fixes: 0985dd306f72 ("media: imx274: V4l2 driver for Sony imx274 CMOS sensor")

Cc: stable@vger.kernel.org # for 4.15 and up
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: unify some sony camera sensors pattern naming

Some Sony camera sensors have same test pattern
definitions, this patch unify the pattern naming
to make it more clear to the userspace.

Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: imx355: fix wrong order in test pattern menus

current imx355 test pattern order in ctrl menu
is not correct, this patch fixes it.

Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: imx319: fix wrong order in test pattern menus

current imx319 test pattern order in ctrl menu
is not correct, this patch fixes it.

Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: v4l2-fwnode: Demote warning to debug level

On a imx6q-wandboard the following warnings are observed:

[    4.327794] video-mux 20e0000.iomuxc-gpr:ipu1_csi0_mux: bad remote port parent
[    4.336118] video-mux 20e0000.iomuxc-gpr:ipu2_csi1_mux: bad remote port parent

As explained by Philipp Zabel:

"There are empty endpoint nodes (without remote-endpoint property)
labeled ipu1_csi[01]_mux_from_parallel_sensor in the i.MX6 device trees
for board DT implementers' convenience. See commit 2539f517acbdc ("ARM:
dts: imx6qdl: Add video multiplexers, mipi_csi, and their connections")."

So demote the warning to debug level and make the wording a bit
less misleading.

Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: firewire: Fix app_info parameter type in avc_ca{,_app}_info

Clang warns:

drivers/media/firewire/firedtv-avc.c:999:45: warning: implicit
conversion from 'int' to 'char' changes value from 159 to -97
[-Wconstant-conversion]
        app_info[0] = (EN50221_TAG_APP_INFO >> 16) & 0xff;
                    ~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~
drivers/media/firewire/firedtv-avc.c:1000:45: warning: implicit
conversion from 'int' to 'char' changes value from 128 to -128
[-Wconstant-conversion]
        app_info[1] = (EN50221_TAG_APP_INFO >>  8) & 0xff;
                    ~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~
drivers/media/firewire/firedtv-avc.c:1040:44: warning: implicit
conversion from 'int' to 'char' changes value from 159 to -97
[-Wconstant-conversion]
        app_info[0] = (EN50221_TAG_CA_INFO >> 16) & 0xff;
                    ~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~
drivers/media/firewire/firedtv-avc.c:1041:44: warning: implicit
conversion from 'int' to 'char' changes value from 128 to -128
[-Wconstant-conversion]
        app_info[1] = (EN50221_TAG_CA_INFO >>  8) & 0xff;
                    ~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~
4 warnings generated.

Change app_info's type to unsigned char to match the type of the
member msg in struct ca_msg, which is the only thing passed into the
app_info parameter in this function.

Link: https://github.com/ClangBuiltLinux/linux/issues/105
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: sti/bdisp: don't pass GFP_DMA32 to dma_alloc_attrs

The DMA API does its own zone decisions based on the coherent_dma_mask.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: imx-pxp: remove duplicated include from imx-pxp.c

Remove duplicated include.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: Staging: media: replace deprecated probe method

Replaced i2c_driver::probe with i2c_driver::probe_new,
because documentation says that probe method is "soon to be deprecated".

Signed-off-by: Andrey Abramov <st5pub@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: ddbridge: remove another duplicate of io.h and sort includes

The io.h was still included twice. Having a large number of
includes like that unsorted is likely the reason why we ended
by having 3 includes of io.h and two includes of interrupt.h
at the first place.

So, let's reorder the includes on alphabetic order. That would
make easier to maintain it.

Fixes: 12645e0655e4 ("media: ddbridge: remove some duplicated include file")
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: ddbridge: remove some duplicated include file

interrupt.h and io.h have duplicated include. hence just remove
redundant file.

Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: tvp5150: fix irq_request error path during probe

Commit 37c65802e76a ("media: tvp5150: Add sync lock interrupt handling")
introduced the interrupt handling. But we have to free the
v4l2_ctrl_handler before we can return the error code.

Fixes: 37c65802e76a ("media: tvp5150: Add sync lock interrupt handling")

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: remove redundant include moduleparam.h

module.h already contained moduleparam.h,  so it is safe to remove
the redundant include.

The issue is detected with the help of Coccinelle.

Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: drivers: media: pci: b2c2: Fix errors due to unappropriate coding style.

Fix error due to assignment in conditional expression.
Fix errors due to absence of empty spaces separators after commas in
function calls.
Fix errors due to lines longer than 80 characters.

Signed-off-by: Iliya Iliev <iliyailiev3592@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: usb: dvb-usb: remove old friio driver

friio drivers is unused and un-compilable since
commit b30cc07de8a9 ("media: dvb-usb/friio, dvb-usb-v2/gl861: decompose
friio and merge with gl861"). Let's remove it.

Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Cc: Akihiro Tsukada <tskd2@yahoo.co.jp>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: lmedm04: use dvb_usbv2_generic_rw_locked

Use dvb-usb-v2 generic usb function for bulk transfers and simplify logic.

Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: lmedm04: Move usb buffer to lme2510_state.

lme2510_state exists for the entire duration of driver.

Move usb_buffer to lme2510_state removing the need for
lme2510_exit_int for removing the buffer.

Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dib7000p: Remove dead code

Clang warns that 'interleaving' is assigned to itself in this function.

drivers/media/dvb-frontends/dib7000p.c:1874:15: warning: explicitly
assigning value of variable of type 'int' to itself [-Wself-assign]
        interleaving = interleaving;
        ~~~~~~~~~~~~ ^ ~~~~~~~~~~~~
1 warning generated.

Just remove the self-assign and leave existing code in place for now.

Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Suggested-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: rtl28xxu: add support for Sony CXD2837ER slave demod

Since 2018 some new revisions of RTL2832P based devices having
Sony CXD2837ER as a slave demodulator instead of Panasonic MN88473.
CXD2837ER handled in DVB_CXD2841ER module but it's has a lack of control.
So slave demod has to be reseted by GPIO0 before detecting to woke up
CXD2837ER.

Signed-off-by: Nikita Gerasimov <nikitych@yandex.ru>
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: uvcvideo: Utilise for_each_uvc_urb iterator

A new iterator is available for processing UVC URB structures. This
simplifies the processing of the internal stream data.

Convert the manual loop iterators to the new helper, adding an index
helper to keep the existing debug print.

Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: uvcvideo: Rename uvc_{un,}init_video()

We have both uvc_init_video() and uvc_video_init() calls which can be
quite confusing to determine the process for each. Now that video
uvc_video_enable() has been renamed to uvc_video_start_streaming(),
adapt these calls to suit the new flow.

Rename uvc_init_video() to uvc_video_start_transfer() and
uvc_uninit_video() to uvc_video_stop_transfer().

Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: uvcvideo: Split uvc_video_enable into two

uvc_video_enable() is used both to start and stop the video stream
object, however the single function entry point shares no code between
the two operations.

Split the function into two distinct calls, and rename to
uvc_video_start_streaming() and uvc_video_stop_streaming() as
appropriate.

Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: uvcvideo: Move decode processing to process context

Newer high definition cameras, and cameras with multiple lenses such as
the range of stereo-vision cameras now available have ever increasing
data rates.

The inclusion of a variable length packet header in URB packets mean
that we must memcpy the frame data out to our destination 'manually'.
This can result in data rates of up to 2 gigabits per second being
processed.

To improve efficiency, and maximise throughput, handle the URB decode
processing through a work queue to move it from interrupt context, and
allow multiple processors to work on URBs in parallel.

Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: uvcvideo: Abstract streaming object lifetime

The streaming object is a key part of handling the UVC device. Although
not critical, we are currently missing a call to destroy the mutex on
clean up paths, and we are due to extend the objects complexity in the
near future.

Facilitate easy management of a stream object by creating a pair of
functions to handle creating and destroying the allocation. The new
uvc_stream_delete() function also performs the missing mutex_destroy()
operation.

Previously a failed streaming object allocation would cause
uvc_parse_streaming() to return -EINVAL, which is inappropriate. If the
constructor failes, we will instead return -ENOMEM.

While we're here, fix the trivial spelling error in the function banner
of uvc_delete().

Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: uvcvideo: queue: Support asynchronous buffer handling

The buffer queue interface currently operates sequentially, processing
buffers after they have fully completed.

In preparation for supporting parallel tasks operating on the buffers,
we will need to support buffers being processed on multiple CPUs.

Adapt the uvc_queue_next_buffer() such that a reference count tracks the
active use of the buffer, returning the buffer to the VB2 stack at
completion.

Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: uvcvideo: queue: Simplify spin-lock usage

Both uvc_start_streaming(), and uvc_stop_streaming() are called from
userspace context, with interrupts enabled. As such, they do not need to
save the IRQ state, and can use spin_lock_irq() and spin_unlock_irq()
respectively.

Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: uvcvideo: Protect queue internals with helper

The URB completion operation obtains the current buffer by reading
directly into the queue internal interface.

Protect this queue abstraction by providing a helper
uvc_queue_get_current_buffer() which can be used by both the decode
task, and the uvc_queue_next_buffer() functions.

Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: uvcvideo: Convert decode functions to use new context structure

The URB completion handlers currently reference the stream context.

Now that each URB has its own context structure, convert the decode (and
one encode) functions to utilise this context for URB management.

Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: uvcvideo: Refactor URB descriptors

We currently store three separate arrays for each URB reference we hold.

Objectify the data needed to track URBs into a single uvc_urb structure,
allowing better object management and tracking of the URB.

All accesses to the data pointers through stream, are converted to use a
uvc_urb pointer for consistency.

Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: seco-cec: add missing header file to fix build

Fix build errors due to missing <linux/module.h> header file.
The header file is inserted first because module-related errors
begin showing up in <linux/acpi.h> (when CONFIG_ACPI is not set).

Sample of build errors:

In file included from ../include/linux/acpi.h:27:0,
                 from ../drivers/media/platform/seco-cec/seco-cec.c:10:
../include/linux/device.h:1620:1: warning: data definition has no type or storage class [enabled by default]
 module_exit(__driver##_exit);
 ^
../include/linux/platform_device.h:229:2: note: in expansion of macro 'module_driver'
  module_driver(__platform_driver, platform_driver_register, \
  ^
../drivers/media/platform/seco-cec/seco-cec.c:791:1: note: in expansion of macro 'module_platform_driver'
 module_platform_driver(secocec_driver);
 ^
../include/linux/device.h:1620:1: error: type defaults to 'int' in declaration of 'module_exit' [-Werror=implicit-int]
 module_exit(__driver##_exit);
 ^
../include/linux/platform_device.h:229:2: note: in expansion of macro 'module_driver'
  module_driver(__platform_driver, platform_driver_register, \
  ^
../drivers/media/platform/seco-cec/seco-cec.c:791:1: note: in expansion of macro 'module_platform_driver'
 module_platform_driver(secocec_driver);
 ^
In file included from ../include/linux/linkage.h:7:0,
                 from ../include/linux/kernel.h:7,
                 from ../include/linux/list.h:9,
                 from ../include/linux/resource_ext.h:17,
                 from ../include/linux/acpi.h:26,
                 from ../drivers/media/platform/seco-cec/seco-cec.c:10:
../include/linux/export.h:18:30: warning: parameter names (without types) in function declaration [enabled by default]
 #define THIS_MODULE ((struct module *)0)
                              ^
../include/linux/platform_device.h:199:34: note: in expansion of macro 'THIS_MODULE'
  __platform_driver_register(drv, THIS_MODULE)
                                  ^
../include/linux/device.h:1613:9: note: in expansion of macro 'platform_driver_register'
  return __register(&(__driver) , ##__VA_ARGS__); \
         ^
../include/linux/platform_device.h:229:2: note: in expansion of macro 'module_driver'
  module_driver(__platform_driver, platform_driver_register, \
  ^
../drivers/media/platform/seco-cec/seco-cec.c:791:1: note: in expansion of macro 'module_platform_driver'
 module_platform_driver(secocec_driver);
 ^
../drivers/media/platform/seco-cec/seco-cec.c:793:20: error: expected declaration specifiers or '...' before string constant
 MODULE_DESCRIPTION("SECO CEC X86 Driver");
                    ^
../drivers/media/platform/seco-cec/seco-cec.c:794:15: error: expected declaration specifiers or '...' before string constant
 MODULE_AUTHOR("Ettore Chimenti <ek5.chimenti@gmail.com>");
               ^
../drivers/media/platform/seco-cec/seco-cec.c:795:16: error: expected declaration specifiers or '...' before string constant
 MODULE_LICENSE("Dual BSD/GPL");
                ^
In file included from ../include/linux/acpi.h:27:0,
                 from ../drivers/media/platform/seco-cec/seco-cec.c:10:
../drivers/media/platform/seco-cec/seco-cec.c:791:24: warning: 'secocec_driver_init' defined but not used [-Wunused-function]
 module_platform_driver(secocec_driver);
                        ^
../include/linux/device.h:1611:19: note: in definition of macro 'module_driver'
 static int __init __driver##_init(void) \
                   ^
../drivers/media/platform/seco-cec/seco-cec.c:791:1: note: in expansion of macro 'module_platform_driver'
 module_platform_driver(secocec_driver);

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Ettore Chimenti <ek5.chimenti@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: vicodec: move the GREY format to the end of the list

With the GREY format at the beginning, the default format selected
by vicodec would be GREY instead of YUV420. That didn't make sense,
so move it to the end of the list.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: tda7432: fix spelling mistake "maximium" -> "maximum"

There is a spelling mistake in the module description as well
as a comment. Fix them.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: vivid: add req_validate error injection

Add a new vivid button control to inject an error into the
req_validate request callback.

This will help testing with v4l2-compliance.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: adv7604 added include of linux/interrupt.h

On older Kernels (prior to 4.15) irqreturn_t and devm_request_threaded_irq
is not defined when compiling adv7604.c. It seems more recent Kernels
include it via another header which is included by adv7604.c.
Now we include linux/interrupt.h explicitly to get the type also defined
for Kernels prior to 4.15.

Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: v4l2-pci-skeleton: depend on CONFIG_SAMPLES

Commit 0185f8501762 ("[media] samples: v4l: from Documentation to
samples directory") moved the v4l2-pci-skeleton driver to the samples
directory. The samples are only be built, if CONFIG_SAMPLES is enabled.

Therefore, VIDEO_PCI_SKELETON is not enough to build the
v4l2-pci-skeleton driver, but SAMPLES needs to be enabled, too. Let
VIDEO_PCI_SKELETON depend on SAMPLES.

Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: v4l2-pci-skeleton: replace vb2_buffer with vb2_v4l2_buffer

Commit 2d7007153f0c ("[media] media: videobuf2: Restructure vb2_buffer")
replaced vb2_buffer with vb2_v4l2_buffer in all v4l2 drivers. The
restructuring skipped the v4l2-pci-skeleton, probably because it resides
outside the drivers directory.

The v4l2_buf_ops assume that the passed buffer is a vb2_v4l2_buffer.
This is not the case if the skel_buffer is based on vb2_buffer instead
of vb2_v4l2_buffer.

Replace vb2_buffer with vb2_v4l2_buffer in the skeleton to make sure
that future drivers that are based on the skeleton use vb2_v4l2_buffer.

Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: v4l: ioctl: Allow drivers to fill in the format description

The v4l_fill_fmtdesc() function does a good job in filling in pixelformat
description. While generally all drivers should depend on this function
doing the job, staging drivers that use their own formats may not.

Allow staging drivers to fill in their own formats by checking whether the
description begins with a non-nil character before issuing the warning.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Suggested-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: v4l: Fix MPEG-2 slice Intra DC Precision validation

intra_dc_precision is a 2-bit integer [1]
allow use of all valid options, 8 - 11 bits precision

[1] ISO/IEC 13818-2 Table 6-13

Fixes: c27bb30e7b6d ("media: v4l: Add definitions for MPEG-2 slice format and metadata")

Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Acked-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: DaVinci-VPBE: fix error handling in vpbe_initialize()

If vpbe_set_default_output() or vpbe_set_default_mode() fails,
vpbe_initialize() returns error code without releasing resources.

The patch adds error handling for that case.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: vivid: fix smatch warnings

Reorganize code to fix two smatch warnings:

drivers/media/platform/vivid/vivid-core.c: drivers/media/platform/vivid/vivid-core.c:889 vivid_create_instance() warn: potentially one past the end of array
'dev->query_dv_timings_qmenu[dev->query_dv_timings_size]'
drivers/media/platform/vivid/vivid-core.c: drivers/media/platform/vivid/vivid-core.c:889 vivid_create_instance() warn: potentially one past the end of array
'dev->query_dv_timings_qmenu[dev->query_dv_timings_size]'

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: mtk-vcodec: Remove VA from encoder frame buffers

The encoder driver has no need to do any CPU access to the source frame
buffers. Use a separate structure for holding DMA addresses and sizes
for those and remove, so we do not end up introducing any erroneous
dereferences of those VAs.

This fixes DMA-buf import from exporters that do not provide contiguous
kernel mappings, which includes the MTK DRM driver.

Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: camss: Take in account sensor skip frames

When streaming is starting ask the sensor for its skip frames value.
Max supported frame skip is 29 frames, so clip it if it is higher.

Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: adv7180: add g_skip_frames support

The adv7180 produces 1 to 2 frames of garbage before proper sync is
established. This allows V4L2 drivers and apps to skip those.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: em28xx: fix spelling mistake, "Cinnergy" -> "Cinergy"

Fix name of the Hybrid T USB XS em28xx card, should be Cinergy.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: exynos4-is: fix spelling mistake ACTURATOR -> ACTUATOR

Trivial fix to spelling mistake in macro name and text string
ERROR_SENSOR_ACTURATOR_INIT_FAIL -> ERROR_SENSOR_ACTUATOR_INIT_FAIL

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: i2c: TDA1997x: select CONFIG_HDMI

Without CONFIG_HDMI, we get a link error for this driver:

drivers/media/i2c/tda1997x.o: In function `tda1997x_parse_infoframe':
tda1997x.c:(.text+0x2195): undefined reference to `hdmi_infoframe_unpack'
tda1997x.c:(.text+0x21b6): undefined reference to `hdmi_infoframe_log'
drivers/media/i2c/tda1997x.o: In function `tda1997x_log_infoframe':
tda1997x.c:(.text.unlikely+0x13d3): undefined reference to `hdmi_infoframe_unpack'
tda1997x.c:(.text.unlikely+0x1426): undefined reference to `hdmi_infoframe_log'

All other drivers in this directory that use HDMI select CONFIG_HDMI,
so do the same here:

Fixes: 9ac0038db9a7 ("media: i2c: Add TDA1997x HDMI receiver driver")

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: uvcvideo: Refactor teardown of uvc on USB disconnect

Currently, disconnecting a USB webcam while it is in use prints out a
number of warnings, such as:

WARNING: CPU: 2 PID: 3118 at /build/linux-ezBi1T/linux-4.8.0/fs/sysfs/group.c:237 sysfs_remove_group+0x8b/0x90
sysfs group ffffffffa7cd0780 not found for kobject 'event13'

This has been noticed before. [0]

This is because of the order in which things are torn down.

If there are no streams active during a USB disconnect:

 - uvc_disconnect() is invoked via device_del() through the bus
   notifier mechanism.

 - this calls uvc_unregister_video().

 - uvc_unregister_video() unregisters the video device for each
   stream,

 - because there are no streams open, it calls uvc_delete()

 - uvc_delete() calls uvc_status_cleanup(), which cleans up the status
   input device.

 - uvc_delete() calls media_device_unregister(), which cleans up the
   media device

 - uvc_delete(), uvc_unregister_video() and uvc_disconnect() all
   return, and we end up back in device_del().

 - device_del() then cleans up the sysfs folder for the camera with
   dpm_sysfs_remove(). Because uvc_status_cleanup() and
   media_device_unregister() have already been called, this all works
   nicely.

If, on the other hand, there *are* streams active during a USB disconnect:

 - uvc_disconnect() is invoked

 - this calls uvc_unregister_video()

 - uvc_unregister_video() unregisters the video device for each
   stream,

 - uvc_unregister_video() and uvc_disconnect() return, and we end up
   back in device_del().

 - device_del() then cleans up the sysfs folder for the camera with
   dpm_sysfs_remove(). Because the status input device and the media
   device are children of the USB device, this also deletes their
   sysfs folders.

 - Sometime later, the final stream is closed, invoking uvc_release().

 - uvc_release() calls uvc_delete()

 - uvc_delete() calls uvc_status_cleanup(), which cleans up the status
   input device. Because the sysfs directory has already been removed,
   this causes a WARNing.

 - uvc_delete() calls media_device_unregister(), which cleans up the
   media device. Because the sysfs directory has already been removed,
   this causes another WARNing.

To fix this, we need to make sure the devices are always unregistered
before the end of uvc_disconnect(). To this, move the unregistration
into the disconnect path:

 - split uvc_status_cleanup() into two parts, one on disconnect that
   unregisters and one on delete that frees.

 - move v4l2_device_unregister() and media_device_unregister() into
   the disconnect path.

[0]: https://lkml.org/lkml/2016/12/8/657

[Renamed uvc_input_cleanup() to uvc_input_unregister()]

Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: uvcvideo: Add support for the CNF4 format

Register the GUID used by Intel RealSense cameras with fourcc CNF4,
encoding depth sensor confidence information for every pixel.

Signed-off-by: Sergey Dorodnicov <sergey.dorodnicov@intel.com>
Signed-off-by: Evgeni Raikhel <evgeni.raikhel@intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: v4l: Add 4bpp packed depth confidence format CNF4

Adding new fourcc CNF4 for 4 bit-per-pixel packed depth confidence
information provided by Intel RealSense cameras. Every two consecutive
pixels are packed into a single byte.

Signed-off-by: Sergey Dorodnicov <sergey.dorodnicov@intel.com>
Signed-off-by: Evgeni Raikhel <evgeni.raikhel@intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: xilinx: fix typo in formats table

In formats table the entry for CFA pattern "rggb" has GRBG fourcc.
This patch fixes it.

Signed-off-by: Mirco Di Salvo <mirco.disalvo@iit.it>
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: xilinx: Use SPDX-License-Identifier

SPDX-License-Identifier is used for the Xilinx Video IP and
related drivers.

[Added drivers/media/platform/xilinx/Kconfig]
[Added drivers/media/platform/xilinx/Makefile]
[Added include/dt-bindings/media/xilinx-vip.h]

Signed-off-by: Dhaval Shah <dhaval23031987@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: sony-cxd2880: add optional vcc regulator to bindings

This patchset adds an optional VCC regulator to the bindings of the Sony
CXD2880 DVB-T2/T tuner + demodulator adapter.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Yasunari Takiguchi <Yasunari.Takiguchi@sony.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: cxd2880-spi: Add optional vcc regulator

This patchset adds an optional VCC regulator to the driver probe function
to make sure power is enabled to the module before starting attaching to
the device.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Yasunari Takiguchi <Yasunari.Takiguchi@sony.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dib0900: fix smatch warnings

drivers/media/dvb-frontends/dib0090.c: drivers/media/dvb-frontends/dib0090.c:1075 dib0090_pwm_gain_reset() warn: '*&bb_ramp_pwm_normal' 2590696709486571520 can't fit into 65535 '*bb_ramp'
drivers/media/dvb-frontends/dib0090.c: drivers/media/dvb-frontends/dib0090.c:1083 dib0090_pwm_gain_reset() warn: '*&bb_ramp_pwm_normal_socs' 2590696709486571520 can't fit into 65535 '*bb_ramp'
drivers/media/dvb-frontends/dib0090.c: drivers/media/dvb-frontends/dib0090.c:1085 dib0090_pwm_gain_reset() warn: '*&rf_ramp_pwm_cband_8090' 2590696709486571520 can't fit into 65535 '*rf_ramp'
drivers/media/dvb-frontends/dib0090.c: drivers/media/dvb-frontends/dib0090.c:1089 dib0090_pwm_gain_reset() warn: '*&rf_ramp_pwm_cband_7090e_sensitivity' 2590696709486571520 can't fit into 65535 '*rf_ramp'
drivers/media/dvb-frontends/dib0090.c: drivers/media/dvb-frontends/dib0090.c:1093 dib0090_pwm_gain_reset() warn: '*&rf_ramp_pwm_cband_7090p' 2590696709486571520 can't fit into 65535 '*rf_ramp'
drivers/media/dvb-frontends/dib0090.c: drivers/media/dvb-frontends/dib0090.c:1096 dib0090_pwm_gain_reset() warn: '*&rf_ramp_pwm_cband' 2590696709486571520 can't fit into 65535 '*rf_ramp'
drivers/media/dvb-frontends/dib0090.c: drivers/media/dvb-frontends/dib0090.c:1101 dib0090_pwm_gain_reset() warn: '*&bb_ramp_pwm_normal_socs' 2590696709486571520 can't fit into 65535 '*bb_ramp'
drivers/media/dvb-frontends/dib0090.c: drivers/media/dvb-frontends/dib0090.c:1104 dib0090_pwm_gain_reset() warn: '*&rf_ramp_pwm_vhf' 2590696709486571520 can't fit into 65535 '*rf_ramp'
drivers/media/dvb-frontends/dib0090.c: drivers/media/dvb-frontends/dib0090.c:1107 dib0090_pwm_gain_reset() warn: '*&bb_ramp_pwm_normal_socs' 2590696709486571520 can't fit into 65535 '*bb_ramp'
drivers/media/dvb-frontends/dib0090.c: drivers/media/dvb-frontends/dib0090.c:1109 dib0090_pwm_gain_reset() warn: '*&rf_ramp_pwm_uhf_8090' 2590696709486571520 can't fit into 65535 '*rf_ramp'
drivers/media/dvb-frontends/dib0090.c: drivers/media/dvb-frontends/dib0090.c:1111 dib0090_pwm_gain_reset() warn: '*&rf_ramp_pwm_uhf_7090' 2590696709486571520 can't fit into 65535 '*rf_ramp'
drivers/media/dvb-frontends/dib0090.c: drivers/media/dvb-frontends/dib0090.c:1113 dib0090_pwm_gain_reset() warn: '*&rf_ramp_pwm_uhf' 2590696709486571520 can't fit into 65535 '*rf_ramp'
drivers/media/dvb-frontends/dib0090.c: drivers/media/dvb-frontends/dib0090.c:1419 dib0090_update_rframp_7090() warn: '*&rf_ramp_pwm_cband_7090e_sensitivity' 2590696709486571520 can't fit into 65535
'*state->rf_ramp'
drivers/media/dvb-frontends/dib0090.c: drivers/media/dvb-frontends/dib0090.c:1421 dib0090_update_rframp_7090() warn: '*&rf_ramp_pwm_cband_7090e_aci' 2590696709486571520 can't fit into 65535
'*state->rf_ramp'

For no apparent reason this code casts away the const of the const u16 arrays, and it
also takes the address of an array. While that's ignored in C I think smatch gets confused
by it.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: mxl5xx: constify dvb_frontend_ops structure

The dvb_frontend_ops structure is only copied into the ops field
of a dvb_frontend structure, so it can be const.

Done with the help of Coccinelle.

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dvb-frontends: Use kmemdup instead of duplicating its function

kmemdup has implemented the function that kmalloc() + memcpy().
We prefer to kmemdup rather than code opened implementation.

Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: usb: Use kmemdup instead of duplicating its function.

kmemdup has implemented the function that kmalloc() + memcpy().
We prefer to kmemdup rather than code opened implementation.

Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: cxd2880-spi: fix probe when dvb_attach fails

When dvb_attach fails, probe returns 0, and remove crashes afterwards.
This patch sets the return value to -ENODEV when attach fails.

Fixes: bd24fcddf6b8 ("media: cxd2880-spi: Add support for CXD2880 SPI interface")

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Yasunari Takiguchi <Yasunari.Takiguchi@sony.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dvb: Use WARM definition from identify_state()

Device should be either COLD or WARM.
This change only make usage of the existing definition.

Signed-off-by: Victor Toso <me@victortoso.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: af9033: Remove duplicated switch statement

The switch before set is_af9035 or is_it9135 which makes the second
switch redundant. Keeping the comment as to avoid sleep on IT9135.

Signed-off-by: Victor Toso <me@victortoso.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dib0700: fix spelling mistake "Amplifyer" -> "Amplifier"

There is a spelling mistake in the MODULE_PARM_DESC text, fix it.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dvb-usb-v2: Fix incorrect use of transfer_flags URB_FREE_BUFFER

commit 1a0c10ed7bb1 ("media: dvb-usb-v2: stop using coherent memory for
URBs") incorrectly adds URB_FREE_BUFFER after every urb transfer.

It cannot use this flag because it reconfigures the URBs accordingly
to suit connected devices. In doing a call to usb_free_urb is made and
invertedly frees the buffers.

The stream buffer should remain constant while driver is up.

Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
CC: stable@vger.kernel.org # v4.18+
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: saa7134: rc-core maintains users count, no need to duplicate

This simplifies the code a little. Tested with suspend and resume.

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: venus: fix reported size of 0-length buffers

The last buffer is often signaled by an empty buffer with the
V4L2_BUF_FLAG_LAST flag set. Such buffers were returned with the
bytesused field set to the full size of the OPB, which leads
user-space to believe that the buffer actually contains useful data. Fix
this by passing the number of bytes reported used by the firmware.

Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Acked-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: venus: dynamic handling of bitrate

Any request for a change in bitrate after both planes
are streamed on is handled by setting the target bitrate
property to hardware.

Signed-off-by: Malathi Gottam <mgottam@codeaurora.org>
Acked-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: venus: handle peak bitrate set property

Max bitrate property is not supported for venus version 4xx.
Return unsupported from packetization layer. Handle it in
hfi_venus layer to exit gracefully to venc layer.

Signed-off-by: Malathi Gottam <mgottam@codeaurora.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Acked-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: venus: add support for USERPTR to queue

Add USERPTR to queue access methods by adding this
support to io_modes on both the planes.

Signed-off-by: Malathi Gottam <mgottam@codeaurora.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Acked-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dvb-pll: don't re-validate tuner frequencies

The dvb_frontend core already checks for the frequencies. No
need for any additional check inside the driver.

It is part of the fixes for the following bug:
  https://bugzilla.opensuse.org/show_bug.cgi?id=1116374

Fixes: a3f90c75b833 ("media: dvb: convert tuner_info frequencies to Hz")
Reported-by: Stakanov Schufter <stakanov@eclipso.eu>
Reported-by: Takashi Iwai <tiwai@suse.de>
Cc: stable@vger.kernel.org # For 4.19
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dvb-pll: fix tuner frequency ranges

Tuners should report frequencies in Hz. That works fine on most
drivers, but, in the case of dvb-pll, some settings are for
satellite tuners, while others are for terrestrial/cable ones.

The code was trying to solve it at probing time, but that doesn't
work, as, when _attach is called, the delivery system may be wrong.

Fix it by ensuring that all frequencies are in Hz at the per-tuner
max/min values.

While here, add a debug message, as this would help to debug any
issues there.

It partially fixes the following bug:
  https://bugzilla.opensuse.org/show_bug.cgi?id=1116374

Fixes: a3f90c75b833 ("media: dvb: convert tuner_info frequencies to Hz")
Reported-by: Stakanov Schufter <stakanov@eclipso.eu>
Reported-by: Takashi Iwai <tiwai@suse.de>
Cc: stable@vger.kernel.org # For 4.19
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dvb_frontend: add debug message for frequency intervals

As we did an internal change inside the subsystem to always
represent min/max frequencies in Hz, add a debug message, as this
would help to discover bugs on drivers, if any.

Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dvb_frontend: don't print function names twice

The dvb_frontend dprintk() macro already prints __func__. So,
we don't need to add it again at the printed message.

Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: vb2: be sure to unlock mutex on errors

As reported by smatch:
drivers/media/common/videobuf2/videobuf2-core.c: drivers/media/common/videobuf2/videobuf2-core.c:2159 vb2_mmap() warn: inconsistent returns 'mutex:&q->mmap_lock'.
  Locked on:   line 2148
  Unlocked on: line 2100
               line 2108
               line 2113
               line 2118
               line 2156
               line 2159

There is one error condition that doesn't unlock a mutex.

Fixes: cd26d1c4d1bc ("media: vb2: vb2_mmap: move lock up")
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: seco-cec: declare ops as static const

As warned by smatch:

drivers/media/platform/seco-cec/seco-cec.c:338:21:  warning: symbol 'secocec_cec_adap_ops' was not declared. Should it be static?

This struct should be static. Also, it is const, so declare it
as such.

Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: seco-cec: fix Makefile

Fix the incorrect obj-y.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: videobuf2-v4l2: drop WARN_ON in vb2_warn_zero_bytesused()

Userspace shouldn't set bytesused to 0 for output buffers.
vb2_warn_zero_bytesused() warns about this (only once!), but it also
calls WARN_ON(1), which is confusing since it is not immediately clear
that it warns about a 0 value for bytesused.

Just drop the WARN_ON as it serves no purpose.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: vb2: Allow reqbufs(0) with "in use" MMAP buffers

Videobuf2 presently does not allow VIDIOC_REQBUFS to destroy outstanding
buffers if the queue is of type V4L2_MEMORY_MMAP, and if the buffers are
considered "in use".  This is different behavior than for other memory
types and prevents us from deallocating buffers in following two cases:

1) There are outstanding mmap()ed views on the buffer. However even if
   we put the buffer in reqbufs(0), there will be remaining references,
   due to vma .open/close() adjusting vb2 buffer refcount appropriately.
   This means that the buffer will be in fact freed only when the last
   mmap()ed view is unmapped.

2) Buffer has been exported as a DMABUF. Refcount of the vb2 buffer
   is managed properly by VB2 DMABUF ops, i.e. incremented on DMABUF
   get and decremented on DMABUF release. This means that the buffer
   will be alive until all importers release it.

Considering both cases above, there does not seem to be any need to
prevent reqbufs(0) operation, because buffer lifetime is already
properly managed by both mmap() and DMABUF code paths. Let's remove it
and allow userspace freeing the queue (and potentially allocating a new
one) even though old buffers might be still in processing.

To let userspace know that the kernel now supports orphaning buffers
that are still in use, add a new V4L2_BUF_CAP_SUPPORTS_ORPHANED_BUFS
to be set by reqbufs and create_bufs.

[p.zabel@pengutronix.de: added V4L2_BUF_CAP_SUPPORTS_ORPHANED_BUFS,
 updated documentation, and added back debug message]

Signed-off-by: John Sheu <sheu@chromium.org>
Reviewed-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: added V4L2-BUF-CAP-SUPPORTS-ORPHANED-BUFS ref]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: cedrus: Get rid of interrupt bottom-half

Now that the mem2mem framework guarantees that .device_run
won't be called from interrupt context, it is safe to call
v4l2_m2m_job_finish directly in the top-half.

So this means the bottom-half is no longer needed and we
can get rid of it.

Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Acked-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: v4l2-mem2mem: Avoid calling .device_run in v4l2_m2m_job_finish

v4l2_m2m_job_finish() is typically called when
DMA operations complete, in interrupt handlers or DMA
completion callbacks. Calling .device_run from v4l2_m2m_job_finish
creates a nasty re-entrancy path into the driver.

Moreover, some implementation of .device_run might need to sleep,
as is the case for drivers supporting the Request API,
where controls are applied via v4l2_ctrl_request_setup,
which takes the ctrl handler mutex.

This commit adds a deferred context that calls v4l2_m2m_try_run,
and gets scheduled by v4l2_m2m_job_finish().

Before this change, device_run would be called from these
paths:

vb2_m2m_request_queue, or
v4l2_m2m_streamon, or
v4l2_m2m_qbuf
  v4l2_m2m_try_schedule
    v4l2_m2m_try_run
      .device_run

v4l2_m2m_job_finish
  v4l2_m2m_try_run
    .device_run

After this change, the latter is now gone and instead:

v4l2_m2m_device_run_work
  v4l2_m2m_try_run
    .device_run

Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: v4l2-mem2mem: Simplify exiting the function in __v4l2_m2m_try_schedule

The __v4l2_m2m_try_schedule function acquires and releases multiple
spinlocks. Simplify unlocking the job lock by adding labels to unlock
the lock and exit the function.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: v4l2-ioctl.c: Simplify locking for m2m devices

Now that the mutexes for output and capture vb2 queues match,
it is possible to refer to the context q_lock as the
m2m lock for a given m2m context.

Remove the output/capture lock selection.

Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: mem2mem: Require capture and output mutexes to match

Currently, all the mem2mem driver either use a single mutex
to lock the capture and output videobuf2 queues, or don't
set any mutex.

This means the mutexes match, and so the mem2mem framework
is able to set the m2m context lock.

Enforce this by making it mandatory for drivers to set
the same capture and output mutex, or not set any mutex at all.

Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dt-bindings: media: Document bindings for venus firmware device

Add devicetree binding documentation for firmware loader for video
hardware running on qualcomm chip.

Signed-off-by: Vikash Garodia <vgarodia@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: venus: firmware: add no TZ boot and shutdown routine

Video hardware is mainly comprised of vcodec subsystem and video
control subsystem. Video control has ARM9 which executes the video
firmware instructions whereas vcodec does the video frame processing.
This change adds support to load the video firmware and bring ARM9
out of reset for platforms which does not have trustzone.
An iommu domain is associated and managed with the firmware device.

Signed-off-by: Vikash Garodia <vgarodia@codeaurora.org>
Acked-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: venus: firmware: register separate platform_device for firmware loader

This registers a firmware platform_device and associate it with
video-firmware DT subnode. Then calls dma configure to initialize
dma and iommu.

Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: venus: firmware: move load firmware in a separate function

Separate firmware loading part into a new function.

Signed-off-by: Vikash Garodia <vgarodia@codeaurora.org>
Acked-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: venus: firmware: add routine to reset ARM9

Add routine to reset the ARM9 and brings it out of reset. Also
abstract the Venus CPU state handling with a new function. This
is in preparation to add PIL functionality in venus driver.

Signed-off-by: Vikash Garodia <vgarodia@codeaurora.org>
Acked-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: vivid: free bitmap_cap when updating std/timings/etc.

When vivid_update_format_cap() is called it should free any overlay
bitmap since the compose size will change.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: syzbot+0cc8e3cc63ca373722c6@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org> # for v3.18 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: v4l2-tpg: array index could become negative

text[s] is a signed char, so using that as index into the font8x16 array
can result in negative indices. Cast it to u8 to be safe.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: syzbot+ccf0a61ed12f2a7313ee@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org> # for v4.7 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: MAINTAINERS fixups

Update file paths in MAINTAINERS.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Joe Perches <joe@perches.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: vb2: check memory model for VIDIOC_CREATE_BUFS

vb2_core_create_bufs did not check if the memory model for newly added
buffers is the same as for already existing buffers. It should return an
error if they aren't the same.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: syzbot+e1fb118a2ebb88031d21@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org> # for v4.16 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>