vfio/iommu_type1: Populate full dirty when detach non-pinned group

[ Upstream commit d0a78f91761fcd837da1e7a4b0f8368873adc646 ]

If a group with non-pinned-page dirty scope is detached with dirty
logging enabled, we should fully populate the dirty bitmaps at the
time it's removed since we don't know the extent of its previous DMA,
nor will the group be present to trigger the full bitmap when the user
retrieves the dirty bitmap.

Fixes: d6a4c185660c ("vfio iommu: Implementation of ioctl for dirty pages tracking")
Suggested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Keqian Zhu <zhukeqian1@huawei.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/msm/dp: trigger unplug event in msm_dp_display_disable

[ Upstream commit c703d5789590935c573bbd080a2166b72d51a017 ]

1. Trigger the unplug event in msm_dp_display_disable() to shutdown audio
   properly.
2. Reset the completion before signal the disconnect event.

Fixes: 158b9aa74479 ("drm/msm/dp: wait for audio notification before disabling clocks")
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/msm: Fix races managing the OOB state for timestamp vs timestamps.

[ Upstream commit 5f98b33b04c02c0d9088c7486c59d058696782f9 ]

Now that we're not racing with GPU setup, also fix races of timestamps
against other timestamps.  In freedreno CI, we were seeing this path trigger
timeouts on setting the GMU bit, producing:

[drm:_a6xx_gmu_set_oob] *ERROR* Timeout waiting for GMU OOB set GPU_SET: 0x0

and this triggered especially on the first set of tests right after
boot (it's probably easier to lose the race than one might think,
given that we start many tests in parallel, and waiting for NFS to
page in code probably means that lots of tests hit the same point of
screen init at the same time).  As of this patch, the message seems to
have completely gone away.

Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: 4b565ca5a2cb ("drm/msm: Add A6XX device support")
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/msm: Fix race of GPU init vs timestamp power management.

[ Upstream commit 7a7cbf2a819740674455ad36155c662367261296 ]

We were using the same force-poweron bit in the two codepaths, so they
could race to have one of them lose GPU power early.

freedreno CI was seeing intermittent errors like:
[drm:_a6xx_gmu_set_oob] *ERROR* Timeout waiting for GMU OOB set GPU_SET: 0x0
and this issue could have contributed to it.

Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: 4b565ca5a2cb ("drm/msm: Add A6XX device support")
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/msm/mdp5: Fix wait-for-commit for cmd panels

[ Upstream commit 68e4f01fddb4ead80e8c7084db489307f22c9cbb ]

Before the offending commit in msm_atomic_commit_tail wait_flush was
called once per frame, after the commit was submitted. After it
wait_flush is also called at the beginning to ensure previous
potentially async commits are done.

For cmd panels the source of wait_flush is a ping-pong irq notifying
a completion. The completion needs to be notified with complete_all so
multiple waiting parties (new async committers) can proceed.

Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Suggested-by: Rob Clark <robdclark@gmail.com>
Fixes: 2d99ced787e3d ("drm/msm: async commit support")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/msm/dsi: Correct io_start for MSM8994 (20nm PHY)

[ Upstream commit 33a7808ce1aea6e2edc1af25db25928137940c02 ]

The previous registers were *almost* correct, but instead of
PHYs, they were pointing at DSI PLLs, resulting in the PHY id
autodetection failing miserably.

Fixes: dcefc117cc19 ("drm/msm/dsi: Add support for msm8x94")
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/msm: Fix MSM_INFO_GET_IOVA with carveout

[ Upstream commit 6cefa31e810404dafdfcdb94874146cea11626c2 ]

The msm_gem_get_iova should be guarded with gpu != NULL and not aspace
!= NULL, because aspace is NULL when using vram carveout.

Fixes: 933415e24bd0d ("drm/msm: Add support for private address space instances")

Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Tested-by: Alexey Minnekhanov <alexeymin@postmarketos.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mei: hbm: call mei_set_devstate() on hbm stop response

[ Upstream commit 3a77df62deb2e62de0dc26c1cb763cc152329287 ]

Use mei_set_devstate() wrapper upon hbm stop command response,
to trigger sysfs event.

Fixes: 43b8a7ed4739 ("mei: expose device state in sysfs")
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20210129120752.850325-3-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: Align checking of syscall user config accessors

[ Upstream commit ef9e4005cbaf022c6251263aa27836acccaef65d ]

After 34e3207205ef ("PCI: handle positive error codes"),
pci_user_read_config_*() and pci_user_write_config_*() return 0 or negative
errno values, not PCIBIOS_* values like PCIBIOS_SUCCESSFUL or
PCIBIOS_BAD_REGISTER_NUMBER.

Remove comparisons with PCIBIOS_SUCCESSFUL and check only for non-zero.  It
happens that PCIBIOS_SUCCESSFUL is zero, so this is not a functional
change, but it aligns this code with the user accessors.

[bhelgaas: commit log]
Fixes: 34e3207205ef ("PCI: handle positive error codes")
Link: https://lore.kernel.org/r/f1220314-e518-1e18-bf94-8e6f8c703758@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

VMCI: Use set_page_dirty_lock() when unregistering guest memory

[ Upstream commit 5a16c535409f8dcb7568e20737309e3027ae3e49 ]

When the VMCI host support releases guest memory in the case where
the VM was killed, the pinned guest pages aren't locked. Use
set_page_dirty_lock() instead of set_page_dirty().

Testing done: Killed VM while having an active VMCI based vSocket
connection and observed warning from ext4. With this fix, no
warning was observed. Ran various vSocket tests without issues.

Fixes: 06164d2b72aa ("VMCI: queue pairs implementation.")
Reviewed-by: Vishnu Dasa <vdasa@vmware.com>
Signed-off-by: Jorgen Hansen <jhansen@vmware.com>
Link: https://lore.kernel.org/r/1611160360-30299-1-git-send-email-jhansen@vmware.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: xilinx-cpm: Fix reference count leak on error path

[ Upstream commit ae191d2e513ae5274224777ae67018a584074a28 ]

Also drop the reference count of the node on error path.

Link: https://lore.kernel.org/r/20210120143745.699-1-bianpan2016@163.com
Fixes: 508f610648b9 ("PCI: xilinx-cpm: Add Versal CPM Root Port driver")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

pwm: rockchip: Eliminate potential race condition when probing

[ Upstream commit d21ba5d6217bd5a6a696678385906ed1994b380b ]

Commit 48cf973cae33 ("pwm: rockchip: Avoid glitches on already running
PWMs") introduced a potential race condition in rockchip_pwm_probe(): A
consumer could enable an inactive PWM, or disable a running one, between
rockchip_pwm_probe() registering the device via pwmchip_add() and checking
whether it is enabled (to determine whether it was started by a
bootloader). This could result in a device's PWM clock being either enabled
once more than necessary, potentially causing it to continue running when
no longer needed, or disabled once more than necessary, producing a warning
from the kernel.

Eliminate these possibilities by modifying rockchip_pwm_probe() so it
checks whether a device is enabled before registering it rather than after.

Fixes: 48cf973cae33 ("pwm: rockchip: Avoid glitches on already running PWMs")
Reported-by: Trent Piepho <tpiepho@gmail.com>
Signed-off-by: Simon South <simon@simonsouth.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

pwm: rockchip: rockchip_pwm_probe(): Remove superfluous clk_unprepare()

[ Upstream commit d5d8d675865ccddfe4da26c85f22c55cec663bf2 ]

If rockchip_pwm_probe() fails to register a PWM device it calls
clk_unprepare() for the device's PWM clock, without having first disabled
the clock and before jumping to an error handler that also unprepares
it. This is likely to produce warnings from the kernel about the clock
being unprepared when it is still enabled, and then being unprepared when
it has already been unprepared.

Prevent these warnings by removing this unnecessary call to
clk_unprepare().

Fixes: 48cf973cae33 ("pwm: rockchip: Avoid glitches on already running PWMs")
Signed-off-by: Simon South <simon@simonsouth.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

pwm: rockchip: Enable APB clock during register access while probing

[ Upstream commit d9b657a5cdbd960de35dee7e06473caf44a9016f ]

Commit 457f74abbed0 ("pwm: rockchip: Keep enabled PWMs running while
probing") modified rockchip_pwm_probe() to access a PWM device's registers
directly to check whether or not the device is enabled, but did not also
change the function so it first enables the device's APB clock to be
certain the device can respond. This risks hanging the kernel on systems
with PWM devices that use more than a single clock.

Avoid this by enabling the device's APB clock before accessing its
registers (and disabling the clock when register access is complete).

Fixes: 457f74abbed0 ("pwm: rockchip: Keep enabled PWMs running while probing")
Reported-by: Thierry Reding <thierry.reding@gmail.com>
Suggested-by: Trent Piepho <tpiepho@gmail.com>
Signed-off-by: Simon South <simon@simonsouth.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

soundwire: cadence: fix ACK/NAK handling

[ Upstream commit db9d9f944f95e7f3aa60ac00cbd502415152c421 ]

The existing code reports a NAK only when ACK=0
This is not aligned with the SoundWire 1.x specifications.

Table 32 in the SoundWire 1.2 specification shows that a Device shall
not set NAK=1 if ACK=1. But Table 33 shows the Combined Response
may very well be NAK=1/ACK=1, e.g. if another Device than the one
addressed reports a parity error.

NAK=1 signals a 'Command_Aborted', regardless of the ACK bit value.

Move the tests for NAK so that the NAK=1/ACK=1 combination is properly
detected according to the specification.

Fixes: 956baa1992f9a ('soundwire: cdns: Add sdw_master_ops and IO transfer support')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210115053738.22630-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: rcar: Always allocate MSI addresses in 32bit space

[ Upstream commit c4e0fec2f7ee013dbf86445394ff47f719408f99 ]

This fixes MSI operation on legacy PCI cards, which cannot issue 64bit MSIs.
The R-Car controller only has one MSI trigger address instead of two, one
for 64bit and one for 32bit MSI, set the address to 32bit PCIe space so that
legacy PCI cards can also trigger MSIs.

Link: https://lore.kernel.org/r/20201016120431.7062-1-marek.vasut@gmail.com
Fixes: 290c1fb35860 ("PCI: rcar: Add MSI support for PCIe")
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: linux-renesas-soc@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

misc: eeprom_93xx46: Add module alias to avoid breaking support for non device tree users

[ Upstream commit 4540b9fbd8ebb21bb3735796d300a1589ee5fbf2 ]

Module alias "spi:93xx46" is used by non device tree users like
drivers/misc/eeprom/digsy_mtc_eeprom.c  and removing it will
break support for them.

Fix this by adding back the module alias "spi:93xx46".

Fixes: 13613a2246bf ("misc: eeprom_93xx46: Fix module alias to enable module autoprobe")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20210113051253.15061-1-a-govindraju@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

phy: cadence-torrent: Fix error code in cdns_torrent_phy_probe()

[ Upstream commit 266df28f9ac16b0dff553d78bc3fb1c084b96b9d ]

This error path should return -EINVAL, but currently it returns
success.

Fixes: d09945eacad0 ("phy: cadence-torrent: Check total lane count for all subnodes is within limit")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/X9s7Wxq+b6ls0q7o@mwanda
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

phy: rockchip-emmc: emmc_phy_init() always return 0

[ Upstream commit 39961bd6b70e5a5d7c4b5483ad8e1db6b5765c60 ]

rockchip_emmc_phy_init() return variable is not set with the error value
if clk_get() failed. 'emmcclk' is optional, thus use clk_get_optional()
and if the return value != NULL make error processing and set the
return code accordingly.

Fixes: 52c0624a10cce phy: rockchip-emmc: Set phyctrl_frqsel based on card clock
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20201210080454.17379-1-chris.ruehl@gtsys.com.hk
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

misc: eeprom_93xx46: Fix module alias to enable module autoprobe

[ Upstream commit 13613a2246bf531f5fc04e8e62e8f21a3d39bf1c ]

Fix module autoprobe by correcting module alias to match the string from
/sys/class/.../spi1.0/modalias content.

Fixes: 06b4501e88ad ("misc/eeprom: add driver for microwire 93xx46 EEPROMs")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20210107163957.28664-2-a-govindraju@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: 9065/1: OABI compat: fix build when EPOLL is not enabled

[ Upstream commit fd749fe4bcb00ad80d9eece709f804bb4ac6bf1e ]

When CONFIG_EPOLL is not set/enabled, sys_oabi-compat.c has build
errors. Fix these by surrounding them with ifdef CONFIG_EPOLL/endif
and providing stubs for the "EPOLL is not set" case.

../arch/arm/kernel/sys_oabi-compat.c: In function 'sys_oabi_epoll_ctl':
../arch/arm/kernel/sys_oabi-compat.c:257:6: error: implicit declaration of function 'ep_op_has_event' [-Werror=implicit-function-declaration]
  257 |  if (ep_op_has_event(op) &&
      |      ^~~~~~~~~~~~~~~
../arch/arm/kernel/sys_oabi-compat.c:264:9: error: implicit declaration of function 'do_epoll_ctl'; did you mean 'sys_epoll_ctl'? [-Werror=implicit-function-declaration]
  264 |  return do_epoll_ctl(epfd, op, fd, &kernel, false);
      |         ^~~~~~~~~~~~

Fixes: c281634c8652 ("ARM: compat: remove KERNEL_DS usage in sys_oabi_epoll_ctl()")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com> # from an lkp .config file
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: patches@armlinux.org.uk
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Input: zinitix - fix return type of zinitix_init_touch()

[ Upstream commit 836f308cb5c72d48e2dff8d3e64c3adb94f4710d ]

zinitix_init_touch() returns error code or 0 for success and therefore
return type must be int, not bool.

Fixes: 26822652c85e ("Input: add zinitix touchscreen driver")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Link: https://lore.kernel.org/r/YC8z2bXc3Oy8pABa@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

sparc: fix led.c driver when PROC_FS is not enabled

[ Upstream commit b3554aa2470b5db1222c31e08ec9c29ab33eabc7 ]

Fix Sparc build when CONFIG_PROC_FS is not enabled.

Fixes this build error:
arch/sparc/kernel/led.c:107:30: error: 'led_proc_ops' defined but not used [-Werror=unused-const-variable=]
     107 | static const struct proc_ops led_proc_ops = {
         |                              ^~~~~~~~~~~~
   cc1: all warnings being treated as errors

Fixes: 97a32539b956 ("proc: convert everything to "struct proc_ops"")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Lars Kotthoff <metalhead@metalhead.ws>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

sparc64: only select COMPAT_BINFMT_ELF if BINFMT_ELF is set

[ Upstream commit 80bddf5c93a99e11fc9faf7e4b575d01cecd45d3 ]

Currently COMPAT on SPARC64 selects COMPAT_BINFMT_ELF unconditionally,
even when BINFMT_ELF is not enabled. This causes a kconfig warning.

Instead, just select COMPAT_BINFMT_ELF if BINFMT_ELF is enabled.
This builds cleanly with no kconfig warnings.

WARNING: unmet direct dependencies detected for COMPAT_BINFMT_ELF
  Depends on [n]: COMPAT [=y] && BINFMT_ELF [=n]
  Selected by [y]:
  - COMPAT [=y] && SPARC64 [=y]

Fixes: 26b4c912185a ("sparc,sparc64: unify Kconfig files")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Input: elo - fix an error code in elo_connect()

[ Upstream commit 0958351e93fa0ac142f6dd8bd844441594f30a57 ]

If elo_setup_10() fails then this should return an error code instead
of success.

Fixes: fae3006e4b42 ("Input: elo - add support for non-pressure-sensitive touchscreens")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YBKFd5CvDu+jVmfW@mwanda
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf test: Fix unaligned access in sample parsing test

[ Upstream commit c5c97cadd7ed13381cb6b4bef5c841a66938d350 ]

The ubsan reported the following error.  It was because sample's raw
data missed u32 padding at the end.  So it broke the alignment of the
array after it.

The raw data contains an u32 size prefix so the data size should have
an u32 padding after 8-byte aligned data.

27: Sample parsing  :util/synthetic-events.c:1539:4:
  runtime error: store to misaligned address 0x62100006b9bc for type
  '__u64' (aka 'unsigned long long'), which requires 8 byte alignment
0x62100006b9bc: note: pointer points here
  00 00 00 00 ff ff ff ff  ff ff ff ff ff ff ff ff  ff ff ff ff ff ff ff ff  ff ff ff ff ff ff ff ff
              ^
    #0 0x561532a9fc96 in perf_event__synthesize_sample util/synthetic-events.c:1539:13
    #1 0x5615327f4a4f in do_test tests/sample-parsing.c:284:8
    #2 0x5615327f3f50 in test__sample_parsing tests/sample-parsing.c:381:9
    #3 0x56153279d3a1 in run_test tests/builtin-test.c:424:9
    #4 0x56153279c836 in test_and_print tests/builtin-test.c:454:9
    #5 0x56153279b7eb in __cmd_test tests/builtin-test.c:675:4
    #6 0x56153279abf0 in cmd_test tests/builtin-test.c:821:9
    #7 0x56153264e796 in run_builtin perf.c:312:11
    #8 0x56153264cf03 in handle_internal_command perf.c:364:8
    #9 0x56153264e47d in run_argv perf.c:408:2
    #10 0x56153264c9a9 in main perf.c:538:3
    #11 0x7f137ab6fbbc in __libc_start_main (/lib64/libc.so.6+0x38bbc)
    #12 0x561532596828 in _start ...

SUMMARY: UndefinedBehaviorSanitizer: misaligned-pointer-use
 util/synthetic-events.c:1539:4 in

Fixes: 045f8cd8542d ("perf tests: Add a sample parsing test")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: https://lore.kernel.org/r/20210214091638.519643-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf intel-pt: Fix IPC with CYC threshold

[ Upstream commit 6af4b60033e0ce0332fcdf256c965ad41942821a ]

The code assumed every CYC-eligible packet has a CYC packet, which is not
the case when CYC thresholds are used. Fix by checking if a CYC packet is
actually present in that case.

Fixes: 5b1dc0fd1da06 ("perf intel-pt: Add support for samples to contain IPC ratio")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: https://lore.kernel.org/r/20210205175350.23817-4-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf intel-pt: Fix premature IPC

[ Upstream commit 20aa39708a5999b7921b27482a756766272286ac ]

The code assumed a change in cycle count means accurate IPC. That is not
correct, for example when sampling both branches and instructions, or at
a FUP packet (which is not CYC-eligible) address. Fix by using an explicit
flag to indicate when IPC can be sampled.

Fixes: 5b1dc0fd1da06 ("perf intel-pt: Add support for samples to contain IPC ratio")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20210205175350.23817-3-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf intel-pt: Fix missing CYC processing in PSB

[ Upstream commit 03fb0f859b45d1eb05c984ab4bd3bef67e45ede2 ]

Add missing CYC packet processing when walking through PSB+. This
improves the accuracy of timestamps that follow PSB+, until the next
MTC.

Fixes: 3d49807870f08 ("perf tools: Add new Intel PT packet definitions")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: https://lore.kernel.org/r/20210205175350.23817-2-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf record: Fix continue profiling after draining the buffer

[ Upstream commit e16c2ce7c5ed5de881066c1fd10ba5c09af69559 ]

Commit da231338ec9c0987 ("perf record: Use an eventfd to wakeup when
done") uses eventfd() to solve a rare race where the setting and
checking of 'done' which add done_fd to pollfd.  When draining buffer,
revents of done_fd is 0 and evlist__filter_pollfd function returns a
non-zero value.  As a result, perf record does not stop profiling.

The following simple scenarios can trigger this condition:

  # sleep 10 &
  # perf record -p $!

After the sleep process exits, perf record should stop profiling and exit.
However, perf record keeps running.

If pollfd revents contains only POLLERR or POLLHUP, perf record
indicates that buffer is draining and need to stop profiling.  Use
fdarray_flag__nonfilterable() to set done eventfd to nonfilterable
objects, so that evlist__filter_pollfd() does not filter and check done
eventfd.

Fixes: da231338ec9c0987 ("perf record: Use an eventfd to wakeup when done")
Signed-off-by: Yang Jihong <yangjihong1@huawei.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Tested-by: Jiri Olsa <jolsa@redhat.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexey Budankov <alexey.budankov@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: zhangjinhao2@huawei.com
Link: http://lore.kernel.org/lkml/20210205065001.23252-1-yangjihong1@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Input: sur40 - fix an error code in sur40_probe()

[ Upstream commit b0b7d2815839024e5181bd2572f5d8d4f65363b3 ]

If v4l2_ctrl_handler_setup() fails then probe() should return an error
code instead of returning success.

Fixes: cee1e3e2ef39 ("media: add video control handlers using V4L2 control framework")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YBKFkbATXa5fA3xj@mwanda
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/rtrs-srv: Do not pass a valid pointer to PTR_ERR()

[ Upstream commit ed408529679737a9a7ad816c8de5d59ba104bb11 ]

smatch gives the warning:

  drivers/infiniband/ulp/rtrs/rtrs-srv.c:1805 rtrs_rdma_connect() warn: passing zero to 'PTR_ERR'

Which is trying to say smatch has shown that srv is not an error pointer
and thus cannot be passed to PTR_ERR.

The solution is to move the list_add() down after full initilization of
rtrs_srv. To avoid holding the srv_mutex too long, only hold it during the
list operation as suggested by Leon.

Fixes: 03e9b33a0fd6 ("RDMA/rtrs: Only allow addition of path to an already established session")
Link: https://lore.kernel.org/r/20210216143807.65923-1-jinpu.wang@cloud.ionos.com
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/rtrs-srv-sysfs: fix missing put_device

[ Upstream commit e2853c49477d104c01d3c7944e1fb5074eb11d9f ]

put_device() decreases the ref-count and then the device will be
cleaned-up, while at is also add missing put_device in
rtrs_srv_create_once_sysfs_root_folders

This patch solves a kmemleak error as below:

  unreferenced object 0xffff88809a7a0710 (size 8):
    comm "kworker/4:1H", pid 113, jiffies 4295833049 (age 6212.380s)
    hex dump (first 8 bytes):
      62 6c 61 00 6b 6b 6b a5                          bla.kkk.
    backtrace:
      [<0000000054413611>] kstrdup+0x2e/0x60
      [<0000000078e3120a>] kobject_set_name_vargs+0x2f/0xb0
      [<00000000f1a17a6b>] dev_set_name+0xab/0xe0
      [<00000000d5502e32>] rtrs_srv_create_sess_files+0x2fb/0x314 [rtrs_server]
      [<00000000ed11a1ef>] rtrs_srv_info_req_done+0x631/0x800 [rtrs_server]
      [<000000008fc5aa8f>] __ib_process_cq+0x94/0x100 [ib_core]
      [<00000000a9599cb4>] ib_cq_poll_work+0x32/0xc0 [ib_core]
      [<00000000cfc376be>] process_one_work+0x4bc/0x980
      [<0000000016e5c96a>] worker_thread+0x78/0x5c0
      [<00000000c20b8be0>] kthread+0x191/0x1e0
      [<000000006c9c0003>] ret_from_fork+0x3a/0x50

Fixes: baa5b28b7a47 ("RDMA/rtrs-srv: Replace device_register with device_initialize and device_add")
Link: https://lore.kernel.org/r/20210212134525.103456-5-jinpu.wang@cloud.ionos.com
Signed-off-by: Gioh Kim <gi-oh.kim@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/rtrs-srv: fix memory leak by missing kobject free

[ Upstream commit f7452a7e96c120d73100387d5f87de9fce7133cb ]

kmemleak reported an error as below:

  unreferenced object 0xffff8880674b7640 (size 64):
    comm "kworker/4:1H", pid 113, jiffies 4296403507 (age 507.840s)
    hex dump (first 32 bytes):
      69 70 3a 31 39 32 2e 31 36 38 2e 31 32 32 2e 31  ip:192.168.122.1
      31 30 40 69 70 3a 31 39 32 2e 31 36 38 2e 31 32  10@ip:192.168.12
    backtrace:
      [<0000000054413611>] kstrdup+0x2e/0x60
      [<0000000078e3120a>] kobject_set_name_vargs+0x2f/0xb0
      [<00000000ca2be3ee>] kobject_init_and_add+0xb0/0x120
      [<0000000062ba5e78>] rtrs_srv_create_sess_files+0x14c/0x314 [rtrs_server]
      [<00000000b45b7217>] rtrs_srv_info_req_done+0x5b1/0x800 [rtrs_server]
      [<000000008fc5aa8f>] __ib_process_cq+0x94/0x100 [ib_core]
      [<00000000a9599cb4>] ib_cq_poll_work+0x32/0xc0 [ib_core]
      [<00000000cfc376be>] process_one_work+0x4bc/0x980
      [<0000000016e5c96a>] worker_thread+0x78/0x5c0
      [<00000000c20b8be0>] kthread+0x191/0x1e0
      [<000000006c9c0003>] ret_from_fork+0x3a/0x50

It is caused by the not-freed kobject of rtrs_srv_sess.  The kobject
embedded in rtrs_srv_sess has ref-counter 2 after calling
process_info_req(). Therefore it must call kobject_put twice.  Currently
it calls kobject_put only once at rtrs_srv_destroy_sess_files because
kobject_del removes the state_in_sysfs flag and then kobject_put in
free_sess() is not called.

This patch moves kobject_del() into free_sess() so that the kobject of
rtrs_srv_sess can be freed. And also this patch adds the missing call of
sysfs_remove_group() to clean-up the sysfs directory.

Fixes: 9cb837480424 ("RDMA/rtrs: server: main functionality")
Link: https://lore.kernel.org/r/20210212134525.103456-4-jinpu.wang@cloud.ionos.com
Signed-off-by: Gioh Kim <gi-oh.kim@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/rtrs: Only allow addition of path to an already established session

[ Upstream commit 03e9b33a0fd677f554b03352646c13459bf60458 ]

While adding a path from the client side to an already established
session, it was possible to provide the destination IP to a different
server. This is dangerous.

This commit adds an extra member to the rtrs_msg_conn_req structure, named
first_conn; which is supposed to notify if the connection request is the
first for that session or not.

On the server side, if a session does not exist but the first_conn
received inside the rtrs_msg_conn_req structure is 1, the connection
request is failed. This signifies that the connection request is for an
already existing session, and since the server did not find one, it is an
wrong connection request.

Fixes: 6a98d71daea1 ("RDMA/rtrs: client: main functionality")
Fixes: 9cb837480424 ("RDMA/rtrs: server: main functionality")
Link: https://lore.kernel.org/r/20210212134525.103456-3-jinpu.wang@cloud.ionos.com
Signed-off-by: Md Haris Iqbal <haris.iqbal@cloud.ionos.com>
Reviewed-by: Lutz Pogrell <lutz.pogrell@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/rtrs-srv: Fix stack-out-of-bounds

[ Upstream commit e6daa8f61d8def10f0619fe51b4c794f69598e4f ]

  BUG: KASAN: stack-out-of-bounds in _mlx4_ib_post_send+0x1bd2/0x2770 [mlx4_ib]
  Read of size 4 at addr ffff8880d5a7f980 by task kworker/0:1H/565

  CPU: 0 PID: 565 Comm: kworker/0:1H Tainted: G           O      5.4.84-storage #5.4.84-1+feature+linux+5.4.y+dbg+20201216.1319+b6b887b~deb10
  Hardware name: Supermicro H8QG6/H8QG6, BIOS 3.00       09/04/2012
  Workqueue: ib-comp-wq ib_cq_poll_work [ib_core]
  Call Trace:
   dump_stack+0x96/0xe0
   print_address_description.constprop.4+0x1f/0x300
   ? irq_work_claim+0x2e/0x50
   __kasan_report.cold.8+0x78/0x92
   ? _mlx4_ib_post_send+0x1bd2/0x2770 [mlx4_ib]
   kasan_report+0x10/0x20
   _mlx4_ib_post_send+0x1bd2/0x2770 [mlx4_ib]
   ? check_chain_key+0x1d7/0x2e0
   ? _mlx4_ib_post_recv+0x630/0x630 [mlx4_ib]
   ? lockdep_hardirqs_on+0x1a8/0x290
   ? stack_depot_save+0x218/0x56e
   ? do_profile_hits.isra.6.cold.13+0x1d/0x1d
   ? check_chain_key+0x1d7/0x2e0
   ? save_stack+0x4d/0x80
   ? save_stack+0x19/0x80
   ? __kasan_slab_free+0x125/0x170
   ? kfree+0xe7/0x3b0
   rdma_write_sg+0x5b0/0x950 [rtrs_server]

The problem is when we send imm_wr, the type should be ib_rdma_wr, so hw
driver like mlx4 can do rdma_wr(wr), so fix it by use the ib_rdma_wr as
type for imm_wr.

Fixes: 9cb837480424 ("RDMA/rtrs: server: main functionality")
Link: https://lore.kernel.org/r/20210212134525.103456-2-jinpu.wang@cloud.ionos.com
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Reviewed-by: Gioh Kim <gi-oh.kim@cloud.ionos.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/ucma: Fix use-after-free bug in ucma_create_uevent

[ Upstream commit fe454dc31e84f8c14cb8942fcb61666c9f40745b ]

ucma_process_join() allocates struct ucma_multicast mc and frees it if an
error occurs during its run.  Specifically, if an error occurs in
copy_to_user(), a use-after-free might happen in the following scenario:

1. mc struct is allocated.
2. rdma_join_multicast() is called and succeeds. During its run,
   cma_iboe_join_multicast() enqueues a work that will later use the
   aforementioned mc struct.
3. copy_to_user() is called and fails.
4. mc struct is deallocated.
5. The work that was enqueued by cma_iboe_join_multicast() is run and
   calls ucma_create_uevent() which tries to access mc struct (which is
   freed by now).

Fix this bug by cancelling the work enqueued by cma_iboe_join_multicast().
Since cma_work_handler() frees struct cma_work, we don't use it in
cma_iboe_join_multicast() so we can safely cancel the work later.

The following syzkaller report revealed it:

   BUG: KASAN: use-after-free in ucma_create_uevent+0x2dd/0x;3f0 drivers/infiniband/core/ucma.c:272
   Read of size 8 at addr ffff88810b3ad110 by task kworker/u8:1/108

   CPU: 1 PID: 108 Comm: kworker/u8:1 Not tainted 5.10.0-rc6+ #257
   Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS   rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
   Workqueue: rdma_cm cma_work_handler
   Call Trace:
    __dump_stack lib/dump_stack.c:77 [inline]
    dump_stack+0xbe/0xf9 lib/dump_stack.c:118
    print_address_description.constprop.0+0x3e/0×60 mm/kasan/report.c:385
    __kasan_report mm/kasan/report.c:545 [inline]
    kasan_report.cold+0x1f/0×37 mm/kasan/report.c:562
    ucma_create_uevent+0x2dd/0×3f0 drivers/infiniband/core/ucma.c:272
    ucma_event_handler+0xb7/0×3c0 drivers/infiniband/core/ucma.c:349
    cma_cm_event_handler+0x5d/0×1c0 drivers/infiniband/core/cma.c:1977
    cma_work_handler+0xfa/0×190 drivers/infiniband/core/cma.c:2718
    process_one_work+0x54c/0×930 kernel/workqueue.c:2272
    worker_thread+0x82/0×830 kernel/workqueue.c:2418
    kthread+0x1ca/0×220 kernel/kthread.c:292
    ret_from_fork+0x1f/0×30 arch/x86/entry/entry_64.S:296

   Allocated by task 359:
     kasan_save_stack+0x1b/0×40 mm/kasan/common.c:48
     kasan_set_track mm/kasan/common.c:56 [inline]
     __kasan_kmalloc mm/kasan/common.c:461 [inline]
     __kasan_kmalloc.constprop.0+0xc2/0xd0 mm/kasan/common.c:434
     kmalloc include/linux/slab.h:552 [inline]
     kzalloc include/linux/slab.h:664 [inline]
     ucma_process_join+0x16e/0×3f0 drivers/infiniband/core/ucma.c:1453
     ucma_join_multicast+0xda/0×140 drivers/infiniband/core/ucma.c:1538
     ucma_write+0x1f7/0×280 drivers/infiniband/core/ucma.c:1724
     vfs_write fs/read_write.c:603 [inline]
     vfs_write+0x191/0×4c0 fs/read_write.c:585
     ksys_write+0x1a1/0×1e0 fs/read_write.c:658
     do_syscall_64+0x2d/0×40 arch/x86/entry/common.c:46
     entry_SYSCALL_64_after_hwframe+0x44/0xa9

   Freed by task 359:
     kasan_save_stack+0x1b/0×40 mm/kasan/common.c:48
     kasan_set_track+0x1c/0×30 mm/kasan/common.c:56
     kasan_set_free_info+0x1b/0×30 mm/kasan/generic.c:355
     __kasan_slab_free+0x112/0×160 mm/kasan/common.c:422
     slab_free_hook mm/slub.c:1544 [inline]
     slab_free_freelist_hook mm/slub.c:1577 [inline]
     slab_free mm/slub.c:3142 [inline]
     kfree+0xb3/0×3e0 mm/slub.c:4124
     ucma_process_join+0x22d/0×3f0 drivers/infiniband/core/ucma.c:1497
     ucma_join_multicast+0xda/0×140 drivers/infiniband/core/ucma.c:1538
     ucma_write+0x1f7/0×280 drivers/infiniband/core/ucma.c:1724
     vfs_write fs/read_write.c:603 [inline]
     vfs_write+0x191/0×4c0 fs/read_write.c:585
     ksys_write+0x1a1/0×1e0 fs/read_write.c:658
     do_syscall_64+0x2d/0×40 arch/x86/entry/common.c:46
     entry_SYSCALL_64_after_hwframe+0x44/0xa9
     The buggy address belongs to the object at ffff88810b3ad100
     which belongs to the cache kmalloc-192 of size 192
     The buggy address is located 16 bytes inside of
     192-byte region [ffff88810b3ad100, ffff88810b3ad1c0)

Fixes: b5de0c60cc30 ("RDMA/cma: Fix use after free race in roce multicast join")
Link: https://lore.kernel.org/r/20210211090517.1278415-1-leon@kernel.org
Reported-by: Amit Matityahu <mitm@nvidia.com>
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/hns: Fixes missing error code of CMDQ

[ Upstream commit 8f86e2eadac968200a6ab1d7074fc0f5cbc1e075 ]

When posting a multi-descriptors command, the error code of previous
failed descriptors may be rewrote to 0 by a later successful descriptor.

Fixes: a04ff739f2a9 ("RDMA/hns: Add command queue support for hip08 RoCE driver")
Link: https://lore.kernel.org/r/1612688143-28226-3-git-send-email-liweihang@huawei.com
Signed-off-by: Lang Cheng <chenglang@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ceph: fix flush_snap logic after putting caps

[ Upstream commit 64f36da5625f7f9853b86750eaa89d499d16a2e9 ]

A primary reason for skipping ceph_check_caps after putting the
references was to avoid the locking in ceph_check_caps during a
reconnect. __ceph_put_cap_refs can still call ceph_flush_snaps in that
case though, and that takes many of the same inconvenient locks.

Fix the logic in __ceph_put_cap_refs to skip flushing snaps when the
skip_checking_caps flag is set.

Fixes: e64f44a88465 ("ceph: skip checking caps when session reconnecting and releasing reqs")
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

svcrdma: Hold private mutex while invoking rdma_accept()

[ Upstream commit 0ac24c320c4d89a9de6ec802591398b8675c7b3c ]

RDMA core mutex locking was restructured by commit d114c6feedfe
("RDMA/cma: Add missing locking to rdma_accept()") [Aug 2020]. When
lock debugging is enabled, the RPC/RDMA server trips over the new
lockdep assertion in rdma_accept() because it doesn't call
rdma_accept() from its CM event handler.

As a temporary fix, have svc_rdma_accept() take the handler_mutex
explicitly. In the meantime, let's consider how to restructure the
RPC/RDMA transport to invoke rdma_accept() from the proper context.

Calls to svc_rdma_accept() are serialized with calls to
svc_rdma_free() by the generic RPC server layer.

Suggested-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/linux-rdma/20210209154014.GO4247@nvidia.com/
Fixes: d114c6feedfe ("RDMA/cma: Add missing locking to rdma_accept()")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nfsd: register pernet ops last, unregister first

[ Upstream commit bd5ae9288d6451bd346a1b4a59d4fe7e62ba29b7 ]

These pernet operations may depend on stuff set up or torn down in the
module init/exit functions.  And they may be called at any time in
between.  So it makes more sense for them to be the last to be
registered in the init function, and the first to be unregistered in the
exit function.

In particular, without this, the drc slab is being destroyed before all
the per-net drcs are shut down, resulting in an "Objects remaining in
nfsd_drc on __kmem_cache_shutdown()" warning in exit_nfsd.

Reported-by: Zhi Li <yieli@redhat.com>
Fixes: 3ba75830ce17 "nfsd4: drc containerization"
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf symbols: Fix return value when loading PE DSO

[ Upstream commit 77771a97011fa9146ccfaf2983a3a2885dc57b6f ]

The first time dso__load() was called on a PE file it always returned -1
error. This caused the first call to map__find_symbol() to always fail
on a PE file so the first sample from each PE file always had symbol
<unknown>. Subsequent samples succeed however because the DSO is already
loaded.

This fixes dso__load() to return 0 when successfully loading a DSO with
libbfd.

Fixes: eac9a4342e5447ca ("perf symbols: Try reading the symbol table with libbfd")
Signed-off-by: Nicholas Fraser <nfraser@codeweavers.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Frank Ch. Eigler <fche@redhat.com>
Cc: Huw Davies <huw@codeweavers.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kim Phillips <kim.phillips@amd.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Remi Bernon <rbernon@codeweavers.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: Tommi Rantala <tommi.t.rantala@nokia.com>
Cc: Ulrich Czekalla <uczekalla@codeweavers.com>
Link: http://lore.kernel.org/lkml/1671b43b-09c3-1911-dbf8-7f030242fbf7@codeweavers.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

printk: avoid prb_first_valid_seq() where possible

[ Upstream commit 13791c80b0cdf54d92fc54221cdf490683b109de ]

If message sizes average larger than expected (more than 32
characters), the data_ring will wrap before the desc_ring. Once the
data_ring wraps, it will start invalidating descriptors. These
invalid descriptors hang around until they are eventually recycled
when the desc_ring wraps. Readers do not care about invalid
descriptors, but they still need to iterate past them. If the
average message size is much larger than 32 characters, then there
will be many invalid descriptors preceding the valid descriptors.

The function prb_first_valid_seq() always begins at the oldest
descriptor and searches for the first valid descriptor. This can
be rather expensive for the above scenario. And, in fact, because
of its heavy usage in /dev/kmsg, there have been reports of long
delays and even RCU stalls.

For code that does not need to search from the oldest record,
replace prb_first_valid_seq() usage with prb_read_valid_*()
functions, which provide a start sequence number to search from.

Fixes: 896fbe20b4e2333fb55 ("printk: use the lockless ringbuffer")
Reported-by: kernel test robot <oliver.sang@intel.com>
Reported-by: J. Avila <elavila@google.com>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20210211173152.1629-1-john.ogness@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>

spi: Skip zero-length transfers in spi_transfer_one_message()

[ Upstream commit b306320322c9cfaa465bc2c7367acf6072b1ac0e ]

With the introduction of 26751de25d25 ("spi: bcm2835: Micro-optimise
FIFO loops") it has become apparent that some users might initiate
zero-length SPI transfers. A fact the micro-optimization omitted, and
which turned out to cause crashes[1].

Instead of changing the micro-optimization itself, use a bigger hammer
and skip zero-length transfers altogether for drivers using the default
transfer_one_message() implementation.

Reported-by: Phil Elwell <phil@raspberrypi.com>
Fixes: 26751de25d25 ("spi: bcm2835: Micro-optimise FIFO loops")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
[1] https://github.com/raspberrypi/linux/issues/4100
Link: https://lore.kernel.org/r/20210211180820.25757-1-nsaenzjulienne@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

spi: dw: Avoid stack content exposure

[ Upstream commit 386f771aad15dd535f2368b4adc9958c0160edd4 ]

Since "data" is u32, &data is a "u32 *" type, which means pointer math
will move in u32-sized steps. This was meant to be a byte offset, so
cast &data to "char *" to aim the copy into the correct location.

Seen with -Warray-bounds (and found by Coverity):

In file included from ./include/linux/string.h:269,
                 from ./arch/powerpc/include/asm/paca.h:15,
                 from ./arch/powerpc/include/asm/current.h:13,
                 from ./include/linux/mutex.h:14,
                 from ./include/linux/notifier.h:14,
                 from ./include/linux/clk.h:14,
                 from drivers/spi/spi-dw-bt1.c:12:
In function 'memcpy',
    inlined from 'dw_spi_bt1_dirmap_copy_from_map' at drivers/spi/spi-dw-bt1.c:87:3:
./include/linux/fortify-string.h:20:29: warning: '__builtin_memcpy' offset 4 is out of the bounds [0, 4] of object 'data' with type 'u32' {aka 'unsigned int'} [-Warray-bounds]
   20 | #define __underlying_memcpy __builtin_memcpy
      |                             ^
./include/linux/fortify-string.h:191:9: note: in expansion of macro '__underlying_memcpy'
  191 |  return __underlying_memcpy(p, q, size);
      |         ^~~~~~~~~~~~~~~~~~~
drivers/spi/spi-dw-bt1.c: In function 'dw_spi_bt1_dirmap_copy_from_map':
drivers/spi/spi-dw-bt1.c:77:6: note: 'data' declared here
   77 |  u32 data;
      |      ^~~~

Addresses-Coverity: CID 1497771 Out-of-bounds access
Fixes: abf00907538e ("spi: dw: Add Baikal-T1 SPI Controller glue driver")
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20210211203714.1929862-1-keescook@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

regulator: bd718x7, bd71828, Fix dvs voltage levels

[ Upstream commit c294554111a835598b557db789d9ad2379b512a2 ]

The ROHM BD718x7 and BD71828 drivers support setting HW state
specific voltages from device-tree. This is used also by various
in-tree DTS files.

These drivers do incorrectly try to compose bit-map using enum
values. By a chance this works for first two valid levels having
values 1 and 2 - but setting values for the rest of the levels
do indicate capability of setting values for first levels as
well. Luckily the regulators which support setting values for
SUSPEND/LPSR do usually also support setting values for RUN
and IDLE too - thus this has not been such a fatal issue.

Fix this by defining the old enum values as bits and fixing the
parsing code. This allows keeping existing IC specific drivers
intact and only slightly changing the rohm-regulator.c

Fixes: 21b72156ede8b ("regulator: bd718x7: Split driver to common and bd718x7 specific parts")
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210212080023.GA880728@localhost.localdomain
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf symbols: Use (long) for iterator for bfd symbols

[ Upstream commit 96de68fff5ded8833bf5832658cb43c54f86ff6c ]

GCC (GCC) 8.4.0 20200304 fails to build perf with:
: util/symbol.c: In function 'dso__load_bfd_symbols':
: util/symbol.c:1626:16: error: comparison of integer expressions of different signednes
:   for (i = 0; i < symbols_count; ++i) {
:                 ^
: util/symbol.c:1632:16: error: comparison of integer expressions of different signednes
:    while (i + 1 < symbols_count &&
:                 ^
: util/symbol.c:1637:13: error: comparison of integer expressions of different signednes
:    if (i + 1 < symbols_count &&
:              ^
: cc1: all warnings being treated as errors

It's unlikely that the symtable will be that big, but the fix is an
oneliner and as perf has CORE_CFLAGS += -Wextra, which makes build to
fail together with CORE_CFLAGS += -Werror

Fixes: eac9a4342e54 ("perf symbols: Try reading the symbol table with libbfd")
Signed-off-by: Dmitry Safonov <dima@arista.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Dmitry Safonov <0x7f454c46@gmail.com>
Cc: Jacek Caban <jacek@codeweavers.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Remi Bernon <rbernon@codeweavers.com>
Link: http://lore.kernel.org/lkml/20210209145148.178702-1-dima@arista.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests/ftrace: Update synthetic event syntax errors

[ Upstream commit b5734e997e1117afb479ffda500e36fa91aea3e8 ]

Some of the synthetic event errors and positions have changed in the
code - update those and add several more tests.

Also add a runtime check to ensure that the kernel supports dynamic
strings in synthetic events, which these tests require.

Link: https://lkml.kernel.org/r/51402656433455baead34f068c6e9466b64df9c0.1612208610.git.zanussi@kernel.org
Fixes: 81ff92a93d95 (selftests/ftrace: Add test case for synthetic event syntax errors)
Reported-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Tom Zanussi <zanussi@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

clk: aspeed: Fix APLL calculate formula from ast2600-A2

[ Upstream commit 6286ce1e3ece54799f12775f8ce2a1cba9cbcfc5 ]

Starting from A2, the A-PLL calculation has changed. Use the
existing formula for A0/A1 and the new formula for A2 onwards.

Fixes: d3d04f6c330a ("clk: Add support for AST2600 SoC")
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
Link: https://lore.kernel.org/r/20210119061715.6043-1-ryan_chen@aspeedtech.com
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

regulator: qcom-rpmh: fix pm8009 ldo7

[ Upstream commit 20ccc362c3d20da734af896e075b74222589f2c0 ]

Use the correct name to avoid ldo7 commands being sent to ldo6's address.

Fixes: 06369bcc15a1 ("regulator: qcom-rpmh: Add support for SM8150")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210211034935.5622-1-jonathan@marek.ca
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/kuap: Restore AMR after replaying soft interrupts

[ Upstream commit 60a707d0c99aff4eadb7fd334c5fd21df386723e ]

Since de78a9c42a79 ("powerpc: Add a framework for Kernel Userspace
Access Protection"), user access helpers call user_{read|write}_access_{begin|end}
when user space access is allowed.

Commit 890274c2dc4c ("powerpc/64s: Implement KUAP for Radix MMU") made
the mentioned helpers program a AMR special register to allow such
access for a short period of time, most of the time AMR is expected to
block user memory access by the kernel.

Since the code accesses the user space memory, unsafe_get_user() calls
might_fault() which calls arch_local_irq_restore() if either
CONFIG_PROVE_LOCKING or CONFIG_DEBUG_ATOMIC_SLEEP is enabled.
arch_local_irq_restore() then attempts to replay pending soft
interrupts as KUAP regions have hardware interrupts enabled.

If a pending interrupt happens to do user access (performance
interrupts do that), it enables access for a short period of time so
after returning from the replay, the user access state remains blocked
and if a user page fault happens - "Bug: Read fault blocked by AMR!"
appears and SIGSEGV is sent.

An example trace:
  Bug: Read fault blocked by AMR!
  WARNING: CPU: 0 PID: 1603 at /home/aik/p/kernel/arch/powerpc/include/asm/book3s/64/kup-radix.h:145
  CPU: 0 PID: 1603 Comm: amr Not tainted 5.10.0-rc6_v5.10-rc6_a+fstn1 #24
  NIP:  c00000000009ece8 LR: c00000000009ece4 CTR: 0000000000000000
  REGS: c00000000dc63560 TRAP: 0700   Not tainted  (5.10.0-rc6_v5.10-rc6_a+fstn1)
  MSR:  8000000000021033 <SF,ME,IR,DR,RI,LE>  CR: 28002888  XER: 20040000
  CFAR: c0000000001fa928 IRQMASK: 1
  GPR00: c00000000009ece4 c00000000dc637f0 c000000002397600 000000000000001f
  GPR04: c0000000020eb318 0000000000000000 c00000000dc63494 0000000000000027
  GPR08: c00000007fe4de68 c00000000dfe9180 0000000000000000 0000000000000001
  GPR12: 0000000000002000 c0000000030a0000 0000000000000000 0000000000000000
  GPR16: 0000000000000000 0000000000000000 0000000000000000 bfffffffffffffff
  GPR20: 0000000000000000 c0000000134a4020 c0000000019c2218 0000000000000fe0
  GPR24: 0000000000000000 0000000000000000 c00000000d106200 0000000040000000
  GPR28: 0000000000000000 0000000000000300 c00000000dc63910 c000000001946730
  NIP __do_page_fault+0xb38/0xde0
  LR  __do_page_fault+0xb34/0xde0
  Call Trace:
    __do_page_fault+0xb34/0xde0 (unreliable)
    handle_page_fault+0x10/0x2c
  --- interrupt: 300 at strncpy_from_user+0x290/0x440
      LR = strncpy_from_user+0x284/0x440
    strncpy_from_user+0x2f0/0x440 (unreliable)
    getname_flags+0x88/0x2c0
    do_sys_openat2+0x2d4/0x5f0
    do_sys_open+0xcc/0x140
    system_call_exception+0x160/0x240
    system_call_common+0xf0/0x27c

To fix it save/restore the AMR when replaying interrupts, and also
add a check if AMR was not blocked prior to replaying interrupts.

Originally found by syzkaller.

Fixes: 890274c2dc4c ("powerpc/64s: Implement KUAP for Radix MMU")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Use normal commit citation format and add full oops log to
      change log, move kuap_check_amr() into the restore routine to
      avoid warnings about unreconciled IRQ state]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210202091541.36499-1-aik@ozlabs.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/uaccess: Avoid might_fault() when user access is enabled

[ Upstream commit 7d506ca97b665b95e698a53697dad99fae813c1a ]

The amount of code executed with enabled user space access (unlocked
KUAP) should be minimal. However with CONFIG_PROVE_LOCKING or
CONFIG_DEBUG_ATOMIC_SLEEP enabled, might_fault() calls into various
parts of the kernel, and may even end up replaying interrupts which in
turn may access user space and forget to restore the KUAP state.

The problem places are:
  1. strncpy_from_user (and similar) which unlock KUAP and call
     unsafe_get_user -> __get_user_allowed -> __get_user_nocheck()
     with do_allow=false to skip KUAP as the caller took care of it.
  2. __unsafe_put_user_goto() which is called with unlocked KUAP.

eg:
  WARNING: CPU: 30 PID: 1 at arch/powerpc/include/asm/book3s/64/kup.h:324 arch_local_irq_restore+0x160/0x190
  NIP arch_local_irq_restore+0x160/0x190
  LR  lock_is_held_type+0x140/0x200
  Call Trace:
    0xc00000007f392ff8 (unreliable)
    ___might_sleep+0x180/0x320
    __might_fault+0x50/0xe0
    filldir64+0x2d0/0x5d0
    call_filldir+0xc8/0x180
    ext4_readdir+0x948/0xb40
    iterate_dir+0x1ec/0x240
    sys_getdents64+0x80/0x290
    system_call_exception+0x160/0x280
    system_call_common+0xf0/0x27c

Change __get_user_nocheck() to look at `do_allow` to decide whether to
skip might_fault(). Since strncpy_from_user/etc call might_fault()
anyway before unlocking KUAP, there should be no visible change.

Drop might_fault() in __unsafe_put_user_goto() as it is only called
from unsafe_put_user(), which already has KUAP unlocked.

Since keeping might_fault() is still desirable for debugging, add
calls to it in user_[read|write]_access_begin(). That also allows us
to drop the is_kernel_addr() test, because there should be no code
using user_[read|write]_access_begin() in order to access a kernel
address.

Fixes: de78a9c42a79 ("powerpc: Add a framework for Kernel Userspace Access Protection")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[mpe: Combine with related patch from myself, merge change logs]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210204121612.32721-1-aik@ozlabs.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>

spi: pxa2xx: Fix the controller numbering for Wildcat Point

[ Upstream commit 54c5d3bfb0cfb7b31259765524567871dee11615 ]

Wildcat Point has two SPI controllers and added one is actually second one.
Fix the numbering by adding the description of the first one.

Fixes: caba248db286 ("spi: spi-pxa2xx-pci: Add ID and driver type for WildcatPoint PCH")
Cc: Leif Liddy <leif.liddy@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210208163816.22147-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

clk: divider: fix initialization with parent_hw

[ Upstream commit 0225daea08141b1dff681502d5af70b71e8b11ec ]

If a driver registers a divider clock with a parent_hw instead of the
parent_name, the parent_hw is ignored and the clock does not have a
parent.

Fix this by initializing the parents the same way they are initialized
for clock gates.

Fixes: ff258817137a ("clk: divider: Add support for specifying parents via DT/pointers")
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/20210121071659.1226489-3-m.tretter@pengutronix.de
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/hns: Disable RQ inline by default

[ Upstream commit 7373de9adb19aebed2781d3fdde576533d626d7a ]

This feature should only be enabled by querying capability from firmware.

Fixes: ba6bb7e97421 ("RDMA/hns: Add interfaces to get pf capabilities from firmware")
Link: https://lore.kernel.org/r/1612517974-31867-5-git-send-email-liweihang@huawei.com
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/hns: Fix type of sq_signal_bits

[ Upstream commit ea4092f3b56b236d08890ea589506ebd76248c53 ]

This bit should be in type of enum ib_sig_type, or there will be a sparse
warning.

Fixes: bfe860351e31 ("RDMA/hns: Fix cast from or to restricted __le32 for driver")
Link: https://lore.kernel.org/r/1612517974-31867-3-git-send-email-liweihang@huawei.com
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/siw: Fix calculation of tx_valid_cpus size

[ Upstream commit 429fa9698957d1a910535ce5e33aedf5adfdabc1 ]

The size of tx_valid_cpus was calculated under the assumption that the
numa nodes identifiers are continuous, which is not the case in all archs
as this could lead to the following panic when trying to access an invalid
tx_valid_cpus index, avoid the following panic by using nr_node_ids
instead of num_online_nodes() to allocate the tx_valid_cpus size.

   Kernel attempted to read user page (8) - exploit attempt? (uid: 0)
   BUG: Kernel NULL pointer dereference on read at 0x00000008
   Faulting instruction address: 0xc0080000081b4a90
   Oops: Kernel access of bad area, sig: 11 [#1]
   LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA PowerNV
   Modules linked in: siw(+) rfkill rpcrdma ib_isert iscsi_target_mod ib_iser libiscsi scsi_transport_iscsi ib_srpt target_core_mod ib_srp scsi_transport_srp ib_ipoib rdma_ucm sunrpc ib_umad rdma_cm ib_cm iw_cm i40iw ib_uverbs ib_core i40e ses enclosure scsi_transport_sas ipmi_powernv ibmpowernv at24 ofpart ipmi_devintf regmap_i2c ipmi_msghandler powernv_flash uio_pdrv_genirq uio mtd opal_prd zram ip_tables xfs libcrc32c sd_mod t10_pi ast i2c_algo_bit drm_vram_helper drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops cec drm_ttm_helper ttm drm vmx_crypto aacraid drm_panel_orientation_quirks dm_mod
   CPU: 40 PID: 3279 Comm: modprobe Tainted: G        W      X --------- ---  5.11.0-0.rc4.129.eln108.ppc64le #2
   NIP:  c0080000081b4a90 LR: c0080000081b4a2c CTR: c0000000007ce1c0
   REGS: c000000027fa77b0 TRAP: 0300   Tainted: G        W      X --------- ---   (5.11.0-0.rc4.129.eln108.ppc64le)
   MSR:  9000000002009033 <SF,HV,VEC,EE,ME,IR,DR,RI,LE>  CR: 44224882  XER: 00000000
   CFAR: c0000000007ce200 DAR: 0000000000000008 DSISR: 40000000 IRQMASK: 0
   GPR00: c0080000081b4a2c c000000027fa7a50 c0080000081c3900 0000000000000040
   GPR04: c000000002023080 c000000012e1c300 000020072ad70000 0000000000000001
   GPR08: c000000001726068 0000000000000008 0000000000000008 c0080000081b5758
   GPR12: c0000000007ce1c0 c0000007fffc3000 00000001590b1e40 0000000000000000
   GPR16: 0000000000000000 0000000000000001 000000011ad68fc8 00007fffcc09c5c8
   GPR20: 0000000000000008 0000000000000000 00000001590b2850 00000001590b1d30
   GPR24: 0000000000043d68 000000011ad67a80 000000011ad67a80 0000000000100000
   GPR28: c000000012e1c300 c0000000020271c8 0000000000000001 c0080000081bf608
   NIP [c0080000081b4a90] siw_init_cpulist+0x194/0x214 [siw]
   LR [c0080000081b4a2c] siw_init_cpulist+0x130/0x214 [siw]
   Call Trace:
   [c000000027fa7a50] [c0080000081b4a2c] siw_init_cpulist+0x130/0x214 [siw] (unreliable)
   [c000000027fa7a90] [c0080000081b4e68] siw_init_module+0x40/0x2a0 [siw]
   [c000000027fa7b30] [c0000000000124f4] do_one_initcall+0x84/0x2e0
   [c000000027fa7c00] [c000000000267ffc] do_init_module+0x7c/0x350
   [c000000027fa7c90] [c00000000026a180] __do_sys_init_module+0x210/0x250
   [c000000027fa7db0] [c0000000000387e4] system_call_exception+0x134/0x230
   [c000000027fa7e10] [c00000000000d660] system_call_common+0xf0/0x27c
   Instruction dump:
   40810044 3d420000 e8bf0000 e88a82d0 3d420000 e90a82c8 792a1f24 7cc4302a
   7d2642aa 79291f24 7d25482a 7d295214 <7d4048a8> 7d4a3b78 7d4049ad 40c2fff4

Fixes: bdcf26bf9b3a ("rdma/siw: network and RDMA core interface")
Link: https://lore.kernel.org/r/20210201112922.141085-1-kamalheib1@gmail.com
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Reviewed-by: Bernard Metzler <bmt@zurich.ibm.com>
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/hns: Fixed wrong judgments in the goto branch

[ Upstream commit bb74fe7e81c8b2b65c6a351a247fdb9a969cbaec ]

When an error occurs, the qp_table must be cleared, regardless of whether
the SRQ feature is enabled.

Fixes: 5c1f167af112 ("RDMA/hns: Init SRQ table for hip08")
Link: https://lore.kernel.org/r/1611997090-48820-5-git-send-email-liweihang@huawei.com
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

kselftests: dmabuf-heaps: Fix Makefile's inclusion of the kernel's usr/include dir

[ Upstream commit 64ba3d591c9d2be2a9c09e99b00732afe002ad0d ]

Copied in from somewhere else, the makefile was including
the kerne's usr/include dir, which caused the asm/ioctl.h file
to be used.

Unfortunately, that file has different values for _IOC_SIZEBITS
and _IOC_WRITE than include/uapi/asm-generic/ioctl.h which then
causes the _IOCW macros to give the wrong ioctl numbers,
specifically for DMA_BUF_IOCTL_SYNC.

This patch simply removes the extra include from the Makefile

Cc: Shuah Khan <shuah@kernel.org>
Cc: Brian Starkey <brian.starkey@arm.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Laura Abbott <labbott@kernel.org>
Cc: Hridya Valsaraju <hridya@google.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Sandeep Patil <sspatil@google.com>
Cc: Daniel Mentz <danielmentz@google.com>
Cc: linux-media@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kselftest@vger.kernel.org
Fixes: a8779927fd86c ("kselftests: Add dma-heap test")
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

kunit: tool: fix unit test cleanup handling

[ Upstream commit cfd607e43da4a20753744f134e201310262b827a ]

* Stop leaking file objects.
* Use self.addCleanup() to ensure we call cleanup functions even if
setUp() fails.
* use mock.patch.stopall instead of more error-prone manual approach

Signed-off-by: Daniel Latypov <dlatypov@google.com>
Reviewed-by: David Gow <davidgow@google.com>
Tested-by: Brendan Higgins <brendanhiggins@google.com>
Acked-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

clk: qcom: gcc-msm8998: Fix Alpha PLL type for all GPLLs

[ Upstream commit 292f75ecff07e8a07fe2e3e19b4b567d0b698842 ]

All of the GPLLs in the MSM8998 Global Clock Controller are Fabia PLLs
and not generic alphas: this was producing bad effects over the entire
clock tree of MSM8998, where any GPLL child clock was declaring a false
clock rate, due to their parent also showing the same.

The issue resides in the calculation of the clock rate for the specific
Alpha PLL type, where Fabia has a different register layout; switching
the MSM8998 GPLLs to the correct Alpha Fabia PLL type fixes the rate
(calculation) reading. While at it, also make these PLLs fixed since
their rate is supposed to *never* be changed while the system runs, as
this would surely crash the entire SoC.

Now all the children of all the PLLs are also complying with their
specified clock table and system stability is improved.

Fixes: b5f5f525c547 ("clk: qcom: Add MSM8998 Global Clock Control (GCC) driver")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210114221059.483390-7-angelogioacchino.delregno@somainline.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/8xx: Fix software emulation interrupt

[ Upstream commit 903178d0ce6bb30ef80a3604ab9ee2b57869fbc9 ]

For unimplemented instructions or unimplemented SPRs, the 8xx triggers
a "Software Emulation Exception" (0x1000). That interrupt doesn't set
reason bits in SRR1 as the "Program Check Exception" does.

Go through emulation_assist_interrupt() to set REASON_ILLEGAL.

Fixes: fbbcc3bb139e ("powerpc/8xx: Remove SoftwareEmulation()")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/ad782af87a222efc79cfb06079b0fd23d4224eaf.1612515180.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/pseries/dlpar: handle ibm, configure-connector delay status

[ Upstream commit 768d70e19ba525debd571b36e6d0ab19956c63d7 ]

dlpar_configure_connector() has two problems in its handling of
ibm,configure-connector's return status:

1. When the status is -2 (busy, call again), we call
   ibm,configure-connector again immediately without checking whether
   to schedule, which can result in monopolizing the CPU.
2. Extended delay status (9900..9905) goes completely unhandled,
   causing the configuration to unnecessarily terminate.

Fix both of these issues by using rtas_busy_delay().

Fixes: ab519a011caa ("powerpc/pseries: Kernel DLPAR Infrastructure")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210107025900.410369-1-nathanl@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

mfd: wm831x-auxadc: Prevent use after free in wm831x_auxadc_read_irq()

[ Upstream commit 26783d74cc6a440ee3ef9836a008a697981013d0 ]

The "req" struct is always added to the "wm831x->auxadc_pending" list,
but it's only removed from the list on the success path.  If a failure
occurs then the "req" struct is freed but it's still on the list,
leading to a use after free.

Fixes: 78bb3688ea18 ("mfd: Support multiple active WM831x AUXADC conversions")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mfd: altera-sysmgr: Fix physical address storing more

[ Upstream commit b0b5b16b78cea1b2b990a69ab8e07a42ccf7a2ed ]

A recent fix improved the way the resource gets passed to
the low-level accessors, but left one warning that appears
in configurations with a resource_size_t that is wider than
a pointer:

In file included from drivers/mfd/altera-sysmgr.c:19:
drivers/mfd/altera-sysmgr.c: In function 'sysmgr_probe':
drivers/mfd/altera-sysmgr.c:148:40: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
  148 |   regmap = devm_regmap_init(dev, NULL, (void *)res->start,
      |                                        ^
include/linux/regmap.h:646:6: note: in definition of macro '__regmap_lockdep_wrapper'
  646 |   fn(__VA_ARGS__, &_key,     \
      |      ^~~~~~~~~~~
drivers/mfd/altera-sysmgr.c:148:12: note: in expansion of macro 'devm_regmap_init'
  148 |   regmap = devm_regmap_init(dev, NULL, (void *)res->start,
      |            ^~~~~~~~~~~~~~~~

I had tried a different approach that would store the address
in the private data as a phys_addr_t, but the easiest solution
now seems to be to add a double cast to shut up the warning.

As the address is passed to an inline assembly, it is guaranteed
to not be wider than a register anyway.

Fixes: d9ca7801b6e5 ("mfd: altera-sysmgr: Fix physical address storing hacks")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

spi: stm32: properly handle 0 byte transfer

[ Upstream commit 2269f5a8b1a7b38651d62676b98182828f29d11a ]

On 0 byte transfer request, return straight from the
xfer function after finalizing the transfer.

Fixes: dcbe0d84dfa5 ("spi: add driver for STM32 SPI controller")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://lore.kernel.org/r/1612551572-495-2-git-send-email-alain.volmat@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/rxe: Correct skb on loopback path

[ Upstream commit 5120bf0a5fc15dec210a0fe0f39e4a256bb6e349 ]

rxe_net.c sends packets at the IP layer with skb->data pointing at the IP
header but receives packets from a UDP tunnel with skb->data pointing at
the UDP header.  On the loopback path this was not correctly accounted
for.  This patch corrects for this by using sbk_pull() to strip the IP
header from the skb on received packets.

Fixes: 8700e3e7c485 ("Soft RoCE driver")
Link: https://lore.kernel.org/r/20210128182301.16859-1-rpearson@hpe.com
Signed-off-by: Bob Pearson <rpearson@hpe.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/rxe: Fix coding error in rxe_rcv_mcast_pkt

[ Upstream commit 8fc1b7027fc162738d5a85c82410e501a371a404 ]

rxe_rcv_mcast_pkt() in rxe_recv.c can leak SKBs in error path code. The
loop over the QPs attached to a multicast group creates new cloned SKBs
for all but the last QP in the list and passes the SKB and its clones to
rxe_rcv_pkt() for further processing. Any QPs that do not pass some checks
are skipped.  If the last QP in the list fails the tests the SKB is
leaked.  This patch checks if the SKB for the last QP was used and if not
frees it. Also removes a redundant loop invariant assignment.

Fixes: 8700e3e7c485 ("Soft RoCE driver")
Fixes: 71abf20b28ff ("RDMA/rxe: Handle skb_clone() failure in rxe_recv.c")
Link: https://lore.kernel.org/r/20210128174752.16128-1-rpearson@hpe.com
Signed-off-by: Bob Pearson <rpearson@hpe.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/rxe: Fix coding error in rxe_recv.c

[ Upstream commit 7d9ae80e31df57dd3253e1ec514f0000aa588a81 ]

check_type_state() in rxe_recv.c is written as if the type bits in the
packet opcode were a bit mask which is not correct. This patch corrects
this code to compare all 3 type bits to the required type.

Fixes: 8700e3e7c485 ("Soft RoCE driver")
Link: https://lore.kernel.org/r/20210127214500.3707-1-rpearson@hpe.com
Signed-off-by: Bob Pearson <rpearson@hpe.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf vendor events arm64: Fix Ampere eMag event typo

[ Upstream commit 2bf797be81fa808f05f1a7a65916619132256a27 ]

The "briefdescription" for event 0x35 has a typo - fix it.

Fixes: d35c595bf005 ("perf vendor events arm64: Revise core JSON events for eMAG")
Signed-off-by: John Garry <john.garry@huawei.com>
Acked-by: Will Deacon <will@kernel.org>
Cc: James Clark <james.clark@arm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Nakamura, Shunsuke/中村 俊介 <nakamura.shun@fujitsu.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linuxarm@openeuler.org
Link: https://lore.kernel.org/r/1611835236-34696-2-git-send-email-john.garry@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf tools: Fix DSO filtering when not finding a map for a sampled address

[ Upstream commit c69bf11ad3d30b6bf01cfa538ddff1a59467c734 ]

When we lookup an address and don't find a map we should filter that
sample if the user specified a list of --dso entries to filter on, fix
it.

Before:

  $ perf script
             sleep 274800  2843.556162:          1 cycles:u:  ffffffffbb26bff4 [unknown] ([unknown])
             sleep 274800  2843.556168:          1 cycles:u:  ffffffffbb2b047d [unknown] ([unknown])
             sleep 274800  2843.556171:          1 cycles:u:  ffffffffbb2706b2 [unknown] ([unknown])
             sleep 274800  2843.556174:          6 cycles:u:  ffffffffbb2b0267 [unknown] ([unknown])
             sleep 274800  2843.556176:         59 cycles:u:  ffffffffbb2b03b1 [unknown] ([unknown])
             sleep 274800  2843.556180:        691 cycles:u:  ffffffffbb26bff4 [unknown] ([unknown])
             sleep 274800  2843.556189:       9160 cycles:u:      7fa9550eeaa3 __GI___tunables_init+0xf3 (/usr/lib64/ld-2.32.so)
             sleep 274800  2843.556312:      86937 cycles:u:      7fa9550e157b _dl_lookup_symbol_x+0x4b (/usr/lib64/ld-2.32.so)
  $

So we have some samples we somehow didn't find in a map for, if we now
do:

  $ perf report --stdio --dso /usr/lib64/ld-2.32.so
  # dso: /usr/lib64/ld-2.32.so
  #
  # Total Lost Samples: 0
  #
  # Samples: 8  of event 'cycles:u'
  # Event count (approx.): 96856
  #
  # Overhead  Command  Symbol
  # ........  .......  ........................
  #
      89.76%  sleep    [.] _dl_lookup_symbol_x
       9.46%  sleep    [.] __GI___tunables_init
       0.71%  sleep    [k] 0xffffffffbb26bff4
       0.06%  sleep    [k] 0xffffffffbb2b03b1
       0.01%  sleep    [k] 0xffffffffbb2b0267
       0.00%  sleep    [k] 0xffffffffbb2706b2
       0.00%  sleep    [k] 0xffffffffbb2b047d
  $

After this patch we get the right output with just entries for the DSOs
specified in --dso:

  $ perf report --stdio --dso /usr/lib64/ld-2.32.so
  # dso: /usr/lib64/ld-2.32.so
  #
  # Total Lost Samples: 0
  #
  # Samples: 8  of event 'cycles:u'
  # Event count (approx.): 96856
  #
  # Overhead  Command  Symbol
  # ........  .......  ........................
  #
      89.76%  sleep    [.] _dl_lookup_symbol_x
       9.46%  sleep    [.] __GI___tunables_init
  $
  #

Fixes: 96415e4d3f5fdf9c ("perf symbols: Avoid unnecessary symbol loading when dso list is specified")
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20210128131209.GD775562@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

rtc: zynqmp: depend on HAS_IOMEM

[ Upstream commit ddd0521549a975e6148732d6ca6b89ffa862c0e5 ]

The Xilinx zynqmp RTC driver makes use of IOMEM functions like
devm_platform_ioremap_resource(), which are only available if
CONFIG_HAS_IOMEM is defined.

This causes the driver not to be enable under make ARCH=um allyesconfig,
even though it won't build.

By adding a dependency on HAS_IOMEM, the driver will not be enabled on
architectures which don't support it.

Fixes: 09ef18bcd5ac ("rtc: use devm_platform_ioremap_resource() to simplify code")
Signed-off-by: David Gow <davidgow@google.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210127035146.1523286-1-davidgow@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

tracepoint: Do not fail unregistering a probe due to memory failure

[ Upstream commit befe6d946551d65cddbd32b9cb0170b0249fd5ed ]

The list of tracepoint callbacks is managed by an array that is protected
by RCU. To update this array, a new array is allocated, the updates are
copied over to the new array, and then the list of functions for the
tracepoint is switched over to the new array. After a completion of an RCU
grace period, the old array is freed.

This process happens for both adding a callback as well as removing one.
But on removing a callback, if the new array fails to be allocated, the
callback is not removed, and may be used after it is freed by the clients
of the tracepoint.

There's really no reason to fail if the allocation for a new array fails
when removing a function. Instead, the function can simply be replaced by a
stub function that could be cleaned up on the next modification of the
array. That is, instead of calling the function registered to the
tracepoint, it would call a stub function in its place.

Link: https://lore.kernel.org/r/20201115055256.65625-1-mmullins@mmlx.us
Link: https://lore.kernel.org/r/20201116175107.02db396d@gandalf.local.home
Link: https://lore.kernel.org/r/20201117211836.54acaef2@oasis.local.home
Link: https://lkml.kernel.org/r/20201118093405.7a6d2290@gandalf.local.home
[ Note, this version does use undefined compiler behavior (assuming that
  a stub function with no parameters or return, can be called by a location
  that thinks it has parameters but still no return value. Static calls
  do the same thing, so this trick is not without precedent.

  There's another solution that uses RCU tricks and is more complex, but
  can be an alternative if this solution becomes an issue.

Link: https://lore.kernel.org/lkml/20210127170721.58bce7cc@gandalf.local.home/
]

Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: Yonghong Song <yhs@fb.com>
Cc: Andrii Nakryiko <andriin@fb.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: KP Singh <kpsingh@chromium.org>
Cc: netdev <netdev@vger.kernel.org>
Cc: bpf <bpf@vger.kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Florian Weimer <fw@deneb.enyo.de>
Fixes: 97e1c18e8d17b ("tracing: Kernel Tracepoints")
Reported-by: syzbot+83aa762ef23b6f0d1991@syzkaller.appspotmail.com
Reported-by: syzbot+d29e58bb557324e55e5e@syzkaller.appspotmail.com
Reported-by: Matt Mullins <mmullins@mmlx.us>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Tested-by: Matt Mullins <mmullins@mmlx.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>

IB/cm: Avoid a loop when device has 255 ports

[ Upstream commit 131be26750379592f0dd6244b2a90bbb504a10bb ]

When RDMA device has 255 ports, loop iterator i overflows.  Due to which
cm_add_one() port iterator loops infinitely.  Use core provided port
iterator to avoid the infinite loop.

Fixes: a977049dacde ("[PATCH] IB: Add the kernel CM implementation")
Link: https://lore.kernel.org/r/20210127150010.1876121-9-leon@kernel.org
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

IB/mlx5: Return appropriate error code instead of ENOMEM

[ Upstream commit d286ac1d05210695c312b9018b3aa7c2048e9aca ]

When mlx5_ib_stage_init_init() fails, return the error code related to
failure instead of -ENOMEM.

Fixes: 16c1975f1032 ("IB/mlx5: Create profile infrastructure to add and remove stages")
Link: https://lore.kernel.org/r/20210127150010.1876121-8-leon@kernel.org
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iommu: Properly pass gfp_t in _iommu_map() to avoid atomic sleeping

[ Upstream commit b8437a3ef8c485903d05d1f261328aaf0c0a6cc2 ]

Sleeping while atomic = bad.  Let's fix an obvious typo to try to avoid it.

The warning that was seen (on a downstream kernel with the problematic
patch backported):

 BUG: sleeping function called from invalid context at mm/page_alloc.c:4726
 in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 9, name: ksoftirqd/0
 CPU: 0 PID: 9 Comm: ksoftirqd/0 Not tainted 5.4.93-12508-gc10c93e28e39 #1
 Call trace:
  dump_backtrace+0x0/0x154
  show_stack+0x20/0x2c
  dump_stack+0xa0/0xfc
  ___might_sleep+0x11c/0x12c
  __might_sleep+0x50/0x84
  __alloc_pages_nodemask+0xf8/0x2bc
  __arm_lpae_alloc_pages+0x48/0x1b4
  __arm_lpae_map+0x124/0x274
  __arm_lpae_map+0x1cc/0x274
  arm_lpae_map+0x140/0x170
  arm_smmu_map+0x78/0xbc
  __iommu_map+0xd4/0x210
  _iommu_map+0x4c/0x84
  iommu_map_atomic+0x44/0x58
  __iommu_dma_map+0x8c/0xc4
  iommu_dma_map_page+0xac/0xf0

Fixes: d8c1df02ac7f ("iommu: Move iotlb_sync_map out from __iommu_map")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Yong Wu <yong.wu@mediatek.com>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210201170611.1.I64a7b62579287d668d7c89e105dcedf45d641063@changeid
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iommu: Move iotlb_sync_map out from __iommu_map

[ Upstream commit d8c1df02ac7f2c802a9b2afc0f5c888c4217f1d5 ]

In the end of __iommu_map, It alway call iotlb_sync_map.

This patch moves iotlb_sync_map out from __iommu_map since it is
unnecessary to call this for each sg segment especially iotlb_sync_map
is flush tlb all currently. Add a little helper _iommu_map for this.

Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210107122909.16317-2-yong.wu@mediatek.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

amba: Fix resource leak for drivers without .remove

[ Upstream commit de5d7adb89367bbc87b4e5ce7afe7ae9bd86dc12 ]

Consider an amba driver with a .probe but without a .remove callback (e.g.
pl061_gpio_driver). The function amba_probe() is called to bind a device
and so dev_pm_domain_attach() and others are called. As there is no remove
callback amba_remove() isn't called at unbind time however and so calling
dev_pm_domain_detach() is missed and the pm domain keeps active.

To fix this always use the core driver callbacks and handle missing amba
callbacks there. For probe refuse registration as a driver without probe
doesn't make sense.

Fixes: 7cfe249475fd ("ARM: AMBA: Add pclk support to AMBA bus infrastructure")
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210126165835.687514-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

i2c: qcom-geni: Store DMA mapping data in geni_i2c_dev struct

[ Upstream commit 357ee8841d0b7bd822f25fc768afbc0c2ab7e47b ]

Store DMA mapping data in geni_i2c_dev struct to enhance DMA mapping
data scope. For example during shutdown callback to unmap DMA mapping,
this stored DMA mapping data can be used to call geni_se_tx_dma_unprep
and geni_se_rx_dma_unprep functions.

Add two helper functions geni_i2c_rx_msg_cleanup and
geni_i2c_tx_msg_cleanup to unwrap the things after rx/tx FIFO/DMA
transfers, so that the same can be used in geni_i2c_stop_xfer()
function during shutdown callback.

Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: 9046/1: decompressor: Do not clear SCTLR.nTLSMD for ARMv7+ cores

[ Upstream commit 2acb909750431030b65a0a2a17fd8afcbd813a84 ]

It was observed that decompressor running on hardware implementing ARM v8.2
Load/Store Multiple Atomicity and Ordering Control (LSMAOC), say, as guest,
would stuck just after:

Uncompressing Linux... done, booting the kernel.

The reason is that it clears nTLSMD bit when disabling caches:

  nTLSMD, bit [3]

  When ARMv8.2-LSMAOC is implemented:

    No Trap Load Multiple and Store Multiple to
    Device-nGRE/Device-nGnRE/Device-nGnRnE memory.

    0b0 All memory accesses by A32 and T32 Load Multiple and Store
        Multiple at EL1 or EL0 that are marked at stage 1 as
        Device-nGRE/Device-nGnRE/Device-nGnRnE memory are trapped and
        generate a stage 1 Alignment fault.

    0b1 All memory accesses by A32 and T32 Load Multiple and Store
        Multiple at EL1 or EL0 that are marked at stage 1 as
        Device-nGRE/Device-nGnRE/Device-nGnRnE memory are not trapped.

  This bit is permitted to be cached in a TLB.

  This field resets to 1.

  Otherwise:

  Reserved, RES1

So as effect we start getting traps we are not quite ready for.

Looking into history it seems that mask used for SCTLR clear came from
the similar code for ARMv4, where bit[3] is the enable/disable bit for
the write buffer. That not applicable to ARMv7 and onwards, so retire
that bit from the masks.

Fixes: 7d09e85448dfa78e3e58186c934449aaf6d49b50 ("[ARM] 4393/2: ARMv7: Add uncompressing code for the new CPU Id format")
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mmc: renesas_sdhi_internal_dmac: Fix DMA buffer alignment from 8 to 128-bytes

[ Upstream commit d7aefb2887601cf1fc3f86f55d43b2c9aece5e8f ]

According to the latest datasheet, the internal DMAC buffer alignment
R-Car Gen3 SDHI HW should be 128-bytes. So, fix it.

Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[shimoda: revise commit description, rebase]
Fixes: 2a68ea7896e3 ("mmc: renesas-sdhi: add support for R-Car Gen3 SDHI DMAC")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/1608114572-1892-2-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mmc: usdhi6rol0: Fix a resource leak in the error handling path of the probe

[ Upstream commit 6052b3c370fb82dec28bcfff6d7ec0da84ac087a ]

A call to 'ausdhi6_dma_release()' to undo a previous call to
'usdhi6_dma_request()' is missing in the error handling path of the probe
function.

It is already present in the remove function.

Fixes: 75fa9ea6e3c0 ("mmc: add a driver for the Renesas usdhi6rol0 SD/SDIO host controller")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20201217210922.165340-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mmc: sdhci-sprd: Fix some resource leaks in the remove function

[ Upstream commit c9c256a8b0dc09c305c409d6264cc016af2ba38d ]

'sdhci_remove_host()' and 'sdhci_pltfm_free()' should be used in place of
'mmc_remove_host()' and 'mmc_free_host()'.

This avoids some resource leaks, is more in line with the error handling
path of the probe function, and is more consistent with other drivers.

Fixes: fb8bd90f83c4 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Orson Zhai <orson.zhai@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201217204236.163446-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mmc: owl-mmc: Fix a resource leak in an error handling path and in the remove function

[ Upstream commit 5d15cbf63515c6183d2ed7c9dd0586b4db23ffb1 ]

'dma_request_chan()' calls should be balanced by a corresponding
'dma_release_channel()' call.

Add the missing call both in the error handling path of the probe function
and in the remove function.

Fixes: ff65ffe46d28 ("mmc: Add Actions Semi Owl SoCs SD/MMC driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20201209194202.54099-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/time: Enable sched clock for irqtime

[ Upstream commit b709e32ef570b8b91dfbcb63cffac4324c87799f ]

When CONFIG_IRQ_TIME_ACCOUNTING and CONFIG_VIRT_CPU_ACCOUNTING_GEN, powerpc
does not enable "sched_clock_irqtime" and can not utilize irq time
accounting.

Like x86, powerpc does not use the sched_clock_register() interface. So it
needs an dedicated call to enable_sched_clock_irqtime() to enable irq time
accounting.

Fixes: 518470fe962e ("powerpc: Add HAVE_IRQ_TIME_ACCOUNTING")
Signed-off-by: Pingfan Liu <kernelfans@gmail.com>
[mpe: Add fixes tag]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1603349479-26185-1-git-send-email-kernelfans@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/47x: Disable 256k page size

[ Upstream commit 910a0cb6d259736a0c86e795d4c2f42af8d0d775 ]

PPC47x_TLBE_SIZE isn't defined for 256k pages, leading to a build
break if 256k pages is selected.

So change the kconfig so that 256k pages can't be selected for 47x.

Fixes: e7f75ad01d59 ("powerpc/47x: Base ppc476 support")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
[mpe: Expand change log to mention build break]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/2fed79b1154c872194f98bac4422c23918325e61.1611128938.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>

KVM: PPC: Make the VMX instruction emulation routines static

[ Upstream commit 9236f57a9e51c72ce426ccd2e53e123de7196a0f ]

These are only used locally. It fixes these W=1 compile errors :

../arch/powerpc/kvm/powerpc.c:1521:5: error: no previous prototype for ‘kvmppc_get_vmx_dword’ [-Werror=missing-prototypes]
 1521 | int kvmppc_get_vmx_dword(struct kvm_vcpu *vcpu, int index, u64 *val)
      |     ^~~~~~~~~~~~~~~~~~~~
../arch/powerpc/kvm/powerpc.c:1539:5: error: no previous prototype for ‘kvmppc_get_vmx_word’ [-Werror=missing-prototypes]
 1539 | int kvmppc_get_vmx_word(struct kvm_vcpu *vcpu, int index, u64 *val)
      |     ^~~~~~~~~~~~~~~~~~~
../arch/powerpc/kvm/powerpc.c:1557:5: error: no previous prototype for ‘kvmppc_get_vmx_hword’ [-Werror=missing-prototypes]
 1557 | int kvmppc_get_vmx_hword(struct kvm_vcpu *vcpu, int index, u64 *val)
      |     ^~~~~~~~~~~~~~~~~~~~
../arch/powerpc/kvm/powerpc.c:1575:5: error: no previous prototype for ‘kvmppc_get_vmx_byte’ [-Werror=missing-prototypes]
 1575 | int kvmppc_get_vmx_byte(struct kvm_vcpu *vcpu, int index, u64 *val)
      |     ^~~~~~~~~~~~~~~~~~~

Fixes: acc9eb9305fe ("KVM: PPC: Reimplement LOAD_VMX/STORE_VMX instruction mmio emulation with analyse_instr() input")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210104143206.695198-19-clg@kaod.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

IB/umad: Return EPOLLERR in case of when device disassociated

[ Upstream commit def4cd43f522253645b72c97181399c241b54536 ]

Currently, polling a umad device will always works, even if the device was
disassociated. A disassociated device should immediately return EPOLLERR
from poll(). Otherwise userspace is endlessly hung on poll() with no idea
that the device has been removed from the system.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Link: https://lore.kernel.org/r/20210125121339.837518-3-leon@kernel.org
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

IB/umad: Return EIO in case of when device disassociated

[ Upstream commit 4fc5461823c9cad547a9bdfbf17d13f0da0d6bb5 ]

MAD message received by the user has EINVAL error in all flows
including when the device is disassociated. That makes it impossible
for the applications to treat such flow differently.

Change it to return EIO, so the applications will be able to perform
disassociation recovery.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Link: https://lore.kernel.org/r/20210125121339.837518-2-leon@kernel.org
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iommu: Switch gather->end to the inclusive end

[ Upstream commit 862c3715de8f3e5350489240c951d697f04bd8c9 ]

Currently gather->end is "unsigned long" which may be overflow in
arch32 in the corner case: 0xfff00000 + 0x100000(iova + size).
Although it doesn't affect the size(end - start), it affects the checking
"gather->end < end"

This patch changes this "end" to the real end address
(end = start + size - 1). Correspondingly, update the length to
"end - start + 1".

Fixes: a7d20dc19d9e ("iommu: Introduce struct iommu_iotlb_gather for batching TLB flushes")
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210107122909.16317-5-yong.wu@mediatek.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: lpfc: Fix ancient double free

[ Upstream commit 0be310979e5e1272d4c5b557642df4da4ce7eba4 ]

The "pmb" pointer is freed at the start of the function and then freed
again in the error handling code.

Link: https://lore.kernel.org/r/YA6E8rO51hE56SVw@mwanda
Fixes: 92d7f7b0cde3 ("[SCSI] lpfc: NPIV: add NPIV support on top of SLI-3")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

objtool: Fix ".cold" section suffix check for newer versions of GCC

[ Upstream commit 34ca59e109bdf69704c33b8eeffaa4c9f71076e5 ]

With my version of GCC 9.3.1 the ".cold" subfunctions no longer have a
numbered suffix, so the trailing period is no longer there.

Presumably this doesn't yet trigger a user-visible bug since most of the
subfunction detection logic is duplicated.   I only found it when
testing vmlinux.o validation.

Fixes: 54262aa28301 ("objtool: Fix sibling call detection")
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/ca0b5a57f08a2fbb48538dd915cc253b5edabb40.1611263461.git.jpoimboe@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

objtool: Fix retpoline detection in asm code

[ Upstream commit 1f9a1b74942485a0a29e7c4a9a9f2fe8aea17766 ]

The JMP_NOSPEC macro branches to __x86_retpoline_*() rather than the
__x86_indirect_thunk_*() wrappers used by C code.  Detect jumps to
__x86_retpoline_*() as retpoline dynamic jumps.

Presumably this doesn't trigger a user-visible bug.  I only found it
when testing vmlinux.o validation.

Fixes: 39b735332cb8 ("objtool: Detect jumps to retpoline thunks")
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/31f5833e2e4f01e3d755889ac77e3661e906c09f.1611263461.git.jpoimboe@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

objtool: Fix error handling for STD/CLD warnings

[ Upstream commit 6f567c9300a5ebd7b18c26dda1c8d6ffbdd0debd ]

Actually return an error (and display a backtrace, if requested) for
directional bit warnings.

Fixes: 2f0f9e9ad7b3 ("objtool: Add Direction Flag validation")
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/dc70f2adbc72f09526f7cab5b6feb8bf7f6c5ad4.1611263461.git.jpoimboe@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

auxdisplay: ht16k33: Fix refresh rate handling

[ Upstream commit e89b0a426721a8ca5971bc8d70aa5ea35c020f90 ]

Drop the call to msecs_to_jiffies(), as "HZ / fbdev->refresh_rate" is
already the number of jiffies to wait.

Fixes: 8992da44c6805d53 ("auxdisplay: ht16k33: Driver for LED controller")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

watchdog: intel-mid_wdt: Postpone IRQ handler registration till SCU is ready

[ Upstream commit f285c9532b5bd3de7e37a6203318437cab79bd9a ]

When SCU is not ready and CONFIG_DEBUG_SHIRQ=y we got deferred probe followed
by fired test IRQ which immediately makes kernel panic. Fix this by delaying
IRQ handler registration till SCU is ready.

Fixes: 80ae679b8f86 ("watchdog: intel-mid_wdt: Convert to use new SCU IPC API")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

isofs: release buffer head before return

[ Upstream commit 0a6dc67a6aa45f19bd4ff89b4f468fc50c4b8daa ]

Release the buffer_head before returning error code in
do_isofs_readdir() and isofs_find_entry().

Fixes: 2deb1acc653c ("isofs: fix access to unallocated memory when reading corrupted filesystem")
Link: https://lore.kernel.org/r/20210118120455.118955-1-bianpan2016@163.com
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

regulator: core: Avoid debugfs: Directory ... already present! error

[ Upstream commit dbe954d8f1635f949a1d9a5d6e6fb749ae022b47 ]

Sometimes regulator_get() gets called twice for the same supply on the
same device. This may happen e.g. when a framework / library is used
which uses the regulator; and the driver itself also needs to enable
the regulator in some cases where the framework will not enable it.

Commit ff268b56ce8c ("regulator: core: Don't spew backtraces on
duplicate sysfs") already takes care of the backtrace which would
trigger when creating a duplicate consumer symlink under
/sys/class/regulator/regulator.%d in this scenario.

Commit c33d442328f5 ("debugfs: make error message a bit more verbose")
causes a new error to get logged in this scenario:

[   26.938425] debugfs: Directory 'wm5102-codec-MICVDD' with parent 'spi-WM510204:00-MICVDD' already present!

There is no _nowarn variant of debugfs_create_dir(), but we can detect
and avoid this problem by checking the return value of the earlier
sysfs_create_link_nowarn() call.

Add a check for the earlier sysfs_create_link_nowarn() failing with
-EEXIST and skip the debugfs_create_dir() call in that case, avoiding
this error getting logged.

Fixes: c33d442328f5 ("debugfs: make error message a bit more verbose")
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210122183250.370571-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

power: supply: smb347-charger: Fix interrupt usage if interrupt is unavailable

[ Upstream commit 6996312642d2dad3070c3d276c7621f35e721f30 ]

The IRQ=0 could be a valid interrupt number in kernel because interrupt
numbers are virtual in a modern kernel. Hence fix the interrupt usage in
a case if interrupt is unavailable by not overriding the interrupt number
which is used by the driver.

Note that currently Nexus 7 is the only know device which uses SMB347
kernel diver and it has a properly working interrupt, hence this patch
doesn't fix any real problems, it's a minor cleanup/improvement.

Fixes: 99298de5df92 ("power: supply: smb347-charger: Replace mutex with IRQ disable/enable")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

power: supply: axp20x_usb_power: Init work before enabling IRQs

[ Upstream commit b5e8642ed95ff6ecc20cc6038fe831affa9d098c ]

The IRQ handler calls mod_delayed_work() on power->vbus_detect. However,
that work item is not initialized until after the IRQs are enabled. If
an IRQ is already pending when the driver is probed, the driver calls
mod_delayed_work() on an uninitialized work item, which causes an oops.

Fixes: bcfb7ae3f50b ("power: supply: axp20x_usb_power: Only poll while offline")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>