Linus Torvalds [Sat, 31 Aug 2013 00:43:17 +0000 (17:43 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) There was a simplification in the ipv6 ndisc packet sending
attempted here, which avoided using memory accounting on the
per-netns ndisc socket for sending NDISC packets. It did fix some
important issues, but it causes regressions so it gets reverted here
too. Specifically, the problem with this change is that the IPV6
output path really depends upon there being a valid skb->sk
attached.
The reason we want to do this change in some form when we figure out
how to do it right, is that if a device goes down the ndisc_sk
socket send queue will fill up and block NDISC packets that we want
to send to other devices too. That's really bad behavior.
Hopefully Thomas can come up with a better version of this change.
2) Fix a severe TCP performance regression by reverting a change made
to dev_pick_tx() quite some time ago. From Eric Dumazet.
3) TIPC returns wrongly signed error codes, fix from Erik Hugne.
4) Fix OOPS when doing IPSEC over ipv4 tunnels due to orphaning the
skb->sk too early. Fix from Li Hongjun.
5) RAW ipv4 sockets can use the wrong routing key during lookup, from
Chris Clark.
6) Similar to #1 revert an older change that tried to use plain
alloc_skb() for SYN/ACK TCP packets, this broke the netfilter owner
mark which needs to see the skb->sk for such frames. From Phil
Oester.
7) BNX2x driver bug fixes from Ariel Elior and Yuval Mintz,
specifically in the handling of virtual functions.
8) IPSEC path error propagations to sockets is not done properly when
we have v4 in v6, and v6 in v4 type rules. Fix from Hannes Frederic
Sowa.
9) Fix missing channel context release in mac80211, from Johannes Berg.
10) Fix network namespace handing wrt. SCM_RIGHTS, from Andy
Lutomirski.
11) Fix usage of bogus NAPI weight in jme, netxen, and ps3_gelic
drivers. From Michal Schmidt.
12) Hopefully a complete and correct fix for the genetlink dump locking
and module reference counting. From Pravin B Shelar.
13) sk_busy_loop() must do a cpu_relax(), from Eliezer Tamir.
14) Fix handling of timestamp offset when restoring a snapshotted TCP
socket. From Andrew Vagin.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
net: fec: fix time stamping logic after napi conversion
net: bridge: convert MLDv2 Query MRC into msecs_to_jiffies for max_delay
mISDN: return -EINVAL on error in dsp_control_req()
net: revert
8728c544a9c ("net: dev_pick_tx() fix")
Revert "ipv6: Don't depend on per socket memory for neighbour discovery messages"
ipv4 tunnels: fix an oops when using ipip/sit with IPsec
tipc: set sk_err correctly when connection fails
tcp: tcp_make_synack() should use sock_wmalloc
bridge: separate querier and query timer into IGMP/IPv4 and MLD/IPv6 ones
ipv6: Don't depend on per socket memory for neighbour discovery messages
ipv4: sendto/hdrincl: don't use destination address found in header
tcp: don't apply tsoffset if rcv_tsecr is zero
tcp: initialize rcv_tstamp for restored sockets
net: xilinx: fix memleak
net: usb: Add HP hs2434 device to ZLP exception table
net: add cpu_relax to busy poll loop
net: stmmac: fixed the pbl setting with DT
genl: Hold reference on correct module while netlink-dump.
genl: Fix genl dumpit() locking.
xfrm: Fix potential null pointer dereference in xdst_queue_output
...
Ian Campbell [Fri, 30 Aug 2013 08:50:42 +0000 (09:50 +0100)]
MAINTAINERS: change my DT related maintainer address
Filtering capabilities on my work email are pretty much non-existent and this
has turned out to be something of a firehose...
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 31 Aug 2013 00:05:02 +0000 (17:05 -0700)]
Merge tag 'sound-3.11' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This contains two Oops fixes (opti9xx and HD-audio) and a simple fixup
for an Acer laptop. All marked as stable patches"
* tag 'sound-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: opti9xx: Fix conflicting driver object name
ALSA: hda - Fix NULL dereference with CONFIG_SND_DYNAMIC_MINORS=n
ALSA: hda - Add inverted digital mic fixup for Acer Aspire One
Linus Torvalds [Fri, 30 Aug 2013 23:18:59 +0000 (16:18 -0700)]
Merge tag 'fixes-for-linus' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Two straggling fixes that I had missed as they were posted a couple of
weeks ago, causing problems with interrupts (breaking them completely)
on the CSR SiRF platforms"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm: prima2: drop nr_irqs in mach as we moved to linear irqdomain
irqchip: sirf: move from legacy mode to linear irqdomain
Linus Torvalds [Fri, 30 Aug 2013 23:17:10 +0000 (16:17 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Since we are getting to the pointy end, one i915 black screen on some
machines, and one vmwgfx stop userspace ability to nuke the VM,
There might be one or two ati or nouveau fixes trickle in before
final, but I think this should pretty much be it"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/vmwgfx: Split GMR2_REMAP commands if they are to large
drm/i915: ivb: fix edp voltage swing reg val
Linus Torvalds [Fri, 30 Aug 2013 23:15:52 +0000 (16:15 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
Pull input layer updates from Dmitry Torokhov:
"Just a couple of new IDs in Wacom and xpad drivers, i8042 is now
disabled on ARC, and data checks in Elantech driver that were overly
relaxed by the previous patch are now tightened"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - disable the driver on ARC platforms
Input: xpad - add signature for Razer Onza Classic Edition
Input: elantech - fix packet check for v3 and v4 hardware
Input: wacom - add support for 0x300 and 0x301
Richard Cochran [Fri, 30 Aug 2013 18:28:10 +0000 (20:28 +0200)]
net: fec: fix time stamping logic after napi conversion
Commit
dc975382 "net: fec: add napi support to improve proformance"
converted the fec driver to the napi model. However, that commit
forgot to remove the call to skb_defer_rx_timestamp which is only
needed in non-napi drivers.
(The function napi_gro_receive eventually calls netif_receive_skb,
which in turn calls skb_defer_rx_timestamp.)
This patch should also be applied to the 3.9 and 3.10 kernels.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Thu, 29 Aug 2013 21:55:05 +0000 (23:55 +0200)]
net: bridge: convert MLDv2 Query MRC into msecs_to_jiffies for max_delay
While looking into MLDv1/v2 code, I noticed that bridging code does
not convert it's max delay into jiffies for MLDv2 messages as we do
in core IPv6' multicast code.
RFC3810, 5.1.3. Maximum Response Code says:
The Maximum Response Code field specifies the maximum time allowed
before sending a responding Report. The actual time allowed, called
the Maximum Response Delay, is represented in units of milliseconds,
and is derived from the Maximum Response Code as follows: [...]
As we update timers that work with jiffies, we need to convert it.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Linus Lüssing <linus.luessing@web.de>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Thu, 29 Aug 2013 08:47:00 +0000 (11:47 +0300)]
mISDN: return -EINVAL on error in dsp_control_req()
If skb->len is too short then we should return an error. Otherwise we
read beyond the end of skb->data for several bytes.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 29 Aug 2013 01:10:43 +0000 (18:10 -0700)]
net: revert
8728c544a9c ("net: dev_pick_tx() fix")
commit
8728c544a9cbdc ("net: dev_pick_tx() fix") and commit
b6fe83e9525a ("bonding: refine IFF_XMIT_DST_RELEASE capability")
are quite incompatible : Queue selection is disabled because skb
dst was dropped before entering bonding device.
This causes major performance regression, mainly because TCP packets
for a given flow can be sent to multiple queues.
This is particularly visible when using the new FQ packet scheduler
with MQ + FQ setup on the slaves.
We can safely revert the first commit now that
416186fbf8c5b
("net: Split core bits of netdev_pick_tx into __netdev_pick_tx")
properly caps the queue_index.
Reported-by: Xi Wang <xii@google.com>
Diagnosed-by: Xi Wang <xii@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Denys Fedorysychenko <nuclearcat@nuclearcat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 30 Aug 2013 21:39:33 +0000 (17:39 -0400)]
Revert "ipv6: Don't depend on per socket memory for neighbour discovery messages"
This reverts commit
1f324e38870cc09659cf23bc626f1b8869e201f2.
It seems to cause regressions, and in particular the output path
really depends upon there being a socket attached to skb->sk for
checks such as sk_mc_loop(skb->sk) for example. See ip6_output_finish2().
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Reported-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Li Hongjun [Wed, 28 Aug 2013 09:54:50 +0000 (11:54 +0200)]
ipv4 tunnels: fix an oops when using ipip/sit with IPsec
Since commit
3d7b46cd20e3 (ip_tunnel: push generic protocol handling to
ip_tunnel module.), an Oops is triggered when an xfrm policy is configured on
an IPv4 over IPv4 tunnel.
xfrm4_policy_check() calls __xfrm_policy_check2(), which uses skb_dst(skb). But
this field is NULL because iptunnel_pull_header() calls skb_dst_drop(skb).
Signed-off-by: Li Hongjun <hongjun.li@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Erik Hugne [Wed, 28 Aug 2013 07:29:58 +0000 (09:29 +0200)]
tipc: set sk_err correctly when connection fails
Should a connect fail, if the publication/server is unavailable or
due to some other error, a positive value will be returned and errno
is never set. If the application code checks for an explicit zero
return from connect (success) or a negative return (failure), it
will not catch the error and subsequent send() calls will fail as
shown from the strace snippet below.
socket(0x1e /* PF_??? */, SOCK_SEQPACKET, 0) = 3
connect(3, {sa_family=0x1e /* AF_??? */, sa_data="\2\1\322\4\0\0\322\4\0\0\0\0\0\0"}, 16) = 111
sendto(3, "test", 4, 0, NULL, 0) = -1 EPIPE (Broken pipe)
The reason for this behaviour is that TIPC wrongly inverts error
codes set in sk_err.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phil Oester [Tue, 27 Aug 2013 23:41:40 +0000 (16:41 -0700)]
tcp: tcp_make_synack() should use sock_wmalloc
In commit
90ba9b19 (tcp: tcp_make_synack() can use alloc_skb()), Eric changed
the call to sock_wmalloc in tcp_make_synack to alloc_skb. In doing so,
the netfilter owner match lost its ability to block the SYNACK packet on
outbound listening sockets. Revert the change, restoring the owner match
functionality.
This closes netfilter bugzilla #847.
Signed-off-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Lüssing [Fri, 30 Aug 2013 15:28:17 +0000 (17:28 +0200)]
bridge: separate querier and query timer into IGMP/IPv4 and MLD/IPv6 ones
Currently we would still potentially suffer multicast packet loss if there
is just either an IGMP or an MLD querier: For the former case, we would
possibly drop IPv6 multicast packets, for the latter IPv4 ones. This is
because we are currently assuming that if either an IGMP or MLD querier
is present that the other one is present, too.
This patch makes the behaviour and fix added in
"bridge: disable snooping if there is no querier" (
b00589af3b04)
to also work if there is either just an IGMP or an MLD querier on the
link: It refines the deactivation of the snooping to be protocol
specific by using separate timers for the snooped IGMP and MLD queries
as well as separate timers for our internal IGMP and MLD queriers.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 30 Aug 2013 00:03:48 +0000 (17:03 -0700)]
Merge branch 'for-3.11-fixes' of git://git./linux/kernel/git/tj/cgroup
Pull cgroup fix from Tejun Heo:
"During the percpu reference counting update which was merged during
v3.11-rc1, the cgroup destruction path was updated so that a cgroup in
the process of dying may linger on the children list, which was
necessary as the cgroup should still be included in child/descendant
iteration while percpu ref is being killed.
Unfortunately, I forgot to update cgroup destruction path accordingly
and cgroup destruction may fail spuriously with -EBUSY due to
lingering dying children even when there's no live child left - e.g.
"rmdir parent/child parent" will usually fail.
This can be easily fixed by iterating through the children list to
verify that there's no live child left. While this is very late in
the release cycle, this bug is very visible to userland and I believe
the fix is relatively safe.
Thanks Hugh for spotting and providing fix for the issue"
* 'for-3.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: fix rmdir EBUSY regression in 3.11
Linus Torvalds [Fri, 30 Aug 2013 00:02:48 +0000 (17:02 -0700)]
Merge branch 'for-3.11-fixes' of git://git./linux/kernel/git/tj/wq
Pull workqueue fix from Tejun Heo:
"This contains one fix which could lead to system-wide lockup on
!PREEMPT kernels. It's very late in the cycle but this definitely is
a -stable material.
The problem is that workqueue worker tasks may process unlimited
number of work items back-to-back without every yielding inbetween.
This usually isn't noticeable but a work item which re-queues itself
waiting for someone else to do something can deadlock with
stop_machine. stop_machine will ensure nothing else happens on all
other cpus and the requeueing work item will reqeueue itself
indefinitely without ever yielding and thus preventing the CPU from
entering stop_machine.
Kudos to Jamie Liu for spotting and diagnosing the problem. This can
be trivially fixed by adding cond_resched() after processing each work
item"
* 'for-3.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: cond_resched() after processing each work item
Linus Torvalds [Fri, 30 Aug 2013 00:00:40 +0000 (17:00 -0700)]
Merge tag 'nfs-for-3.11-5' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfix from Trond Myklebust:
"Stable patch to fix a highmem-related data corruption issue on 32-bit
ARM platforms"
* tag 'nfs-for-3.11-5' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
SUNRPC: Fix memory corruption issue on 32-bit highmem systems
Jakob Bornecrantz [Thu, 29 Aug 2013 00:32:53 +0000 (02:32 +0200)]
drm/vmwgfx: Split GMR2_REMAP commands if they are to large
This fixes the piglit test texturing/max-texture-size
causing the VM to die due to a too large SVGA command.
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Reviewed-by: Biran Paul <brianp@vmware.com>
Reviewed-by: Zack Rusin <zackr@vmware.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@gmail.com>
Dave Airlie [Thu, 29 Aug 2013 23:02:57 +0000 (09:02 +1000)]
Merge tag 'drm-intel-fixes-2013-08-30' of git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Just a one-line patch to fix a black screen issue on rare ivb machines,
cc: stable. Normally I'd just shovel this into the -next pull request this
late in the -rc cycle, but Linus was making noises about not getting real
fixes which are cc: stable. So here we go ;-)
* tag 'drm-intel-fixes-2013-08-30' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: ivb: fix edp voltage swing reg val
Imre Deak [Fri, 23 Aug 2013 20:50:23 +0000 (23:50 +0300)]
drm/i915: ivb: fix edp voltage swing reg val
Fix the typo introduced in
commit
1a2eb4604b85c5efb343da8a4dcf41288fcfca85
Author: Keith Packard <keithp@keithp.com>
Date: Wed Nov 16 16:26:07 2011 -0800
drm/i915: Hook up Ivybridge eDP
This fixes eDP link-training failures and cases where all voltage swing
/pre-emphasis levels were tried and failed during clock recovery and -
as a fallback - we go on to do channel equalization with the last voltage
swing/pre-emphasis level which will succeed. Both issues can lead to a
blank screen.
v2:
- improve commit message
CC: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=64880
Tested-by: Jeremy Moles <cubicool@gmail.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
David S. Miller [Thu, 29 Aug 2013 20:05:30 +0000 (16:05 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
This pull request fixes some issues that arise when 6in4 or 4in6 tunnels
are used in combination with IPsec, all from Hannes Frederic Sowa and a
null pointer dereference when queueing packets to the policy hold queue.
1) We might access the local error handler of the wrong address family if
6in4 or 4in6 tunnel is protected by ipsec. Fix this by addind a pointer
to the correct local_error to xfrm_state_afinet.
2) Add a helper function to always refer to the correct interpretation
of skb->sk.
3) Call skb_reset_inner_headers to record the position of the inner headers
when adding a new one in various ipv6 tunnels. This is needed to identify
the addresses where to send back errors in the xfrm layer.
4) Dereference inner ipv6 header if encapsulated to always call the
right error handler.
5) Choose protocol family by skb protocol to not call the wrong
xfrm{4,6}_local_error handler in case an ipv6 sockets is used
in ipv4 mode.
6) Partly revert "xfrm: introduce helper for safe determination of mtu"
because this introduced pmtu discovery problems.
7) Set skb->protocol on tcp, raw and ip6_append_data genereated skbs.
We need this to get the correct mtu informations in xfrm.
8) Fix null pointer dereference in xdst_queue_output.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Graf [Tue, 27 Aug 2013 23:07:25 +0000 (01:07 +0200)]
ipv6: Don't depend on per socket memory for neighbour discovery messages
Allocating skbs when sending out neighbour discovery messages
currently uses sock_alloc_send_skb() based on a per net namespace
socket and thus share a socket wmem buffer space.
If a netdevice is temporarily unable to transmit due to carrier
loss or for other reasons, the queued up ndisc messages will cosnume
all of the wmem space and will thus prevent from any more skbs to
be allocated even for netdevices that are able to transmit packets.
The number of neighbour discovery messages sent is very limited,
simply use alloc_skb() and don't depend on any socket wmem space any
longer.
This patch has orginally been posted by Eric Dumazet in a modified
form.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Clark [Tue, 27 Aug 2013 18:02:15 +0000 (12:02 -0600)]
ipv4: sendto/hdrincl: don't use destination address found in header
ipv4: raw_sendmsg: don't use header's destination address
A sendto() regression was bisected and found to start with commit
f8126f1d5136be1 (ipv4: Adjust semantics of rt->rt_gateway.)
The problem is that it tries to ARP-lookup the constructed packet's
destination address rather than the explicitly provided address.
Fix this using FLOWI_FLAG_KNOWN_NH so that given nexthop is used.
cf. commit
2ad5b9e4bd314fc685086b99e90e5de3bc59e26b
Reported-by: Chris Clark <chris.clark@alcatel-lucent.com>
Bisected-by: Chris Clark <chris.clark@alcatel-lucent.com>
Tested-by: Chris Clark <chris.clark@alcatel-lucent.com>
Suggested-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Chris Clark <chris.clark@alcatel-lucent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Vagin [Tue, 27 Aug 2013 08:21:55 +0000 (12:21 +0400)]
tcp: don't apply tsoffset if rcv_tsecr is zero
The zero value means that tsecr is not valid, so it's a special case.
tsoffset is used to customize tcp_time_stamp for one socket.
tsoffset is usually zero, it's used when a socket was moved from one
host to another host.
Currently this issue affects logic of tcp_rcv_rtt_measure_ts. Due to
incorrect value of rcv_tsecr, tcp_rcv_rtt_measure_ts sets rto to
TCP_RTO_MAX.
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Reported-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Vagin [Tue, 27 Aug 2013 08:20:40 +0000 (12:20 +0400)]
tcp: initialize rcv_tstamp for restored sockets
u32 rcv_tstamp; /* timestamp of last received ACK */
Its value used in tcp_retransmit_timer, which closes socket
if the last ack was received more then TCP_RTO_MAX ago.
Currently rcv_tstamp is initialized to zero and if tcp_retransmit_timer
is called before receiving a first ack, the connection is closed.
This patch initializes rcv_tstamp to a timestamp, when a socket was
restored.
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Reported-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Barry Song [Tue, 6 Aug 2013 05:37:14 +0000 (13:37 +0800)]
arm: prima2: drop nr_irqs in mach as we moved to linear irqdomain
we don't need nr_irqs in machine any more after we move to
linear irqdomain for sirfsoc irqchip, so drop them.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Barry Song [Tue, 6 Aug 2013 05:37:13 +0000 (13:37 +0800)]
irqchip: sirf: move from legacy mode to linear irqdomain
the series of patches for irqdomain core in 3.11 has broken sirf
irq which uses legacy mapping. all users fail in the new kernel
while setupping irq.
this patch moves to linear irqdomain and drop old legacy irqdomain
codes since we don't need it any more, and at the same time, it
also fixes the broken interrupts of sirfsoc in 3.11.
on the other hand, we actually only have 64 interrupt sources for
prima2 and atlas6, but there are 128 interrupt souces for marco
which uses GIC. in the legacy codes, sirf gpio also uses legacy
irqdomain, so to make gpio interrupt mapping not depend on the
prima2/atlas6/marco an use unified marco,we enlarge prima2/atlas6
interrupt number to 128. here we don't need this workaround any
more as sirf gpio also moved to linear mode before. so we move
SIRFSOC_NUM_IRQS back to 64 too.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Mischa Jonker [Thu, 29 Aug 2013 16:29:40 +0000 (09:29 -0700)]
Input: i8042 - disable the driver on ARC platforms
It causes crashes when enabled, and we don't have such a peripheral
anyway on ARC platforms.
Signed-off-by: Mischa Jonker <mjonker@synopsys.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Hugh Dickins [Wed, 28 Aug 2013 23:31:23 +0000 (16:31 -0700)]
cgroup: fix rmdir EBUSY regression in 3.11
On 3.11-rc we are seeing cgroup directories left behind when they should
have been removed. Here's a trivial reproducer:
cd /sys/fs/cgroup/memory
mkdir parent parent/child; rmdir parent/child parent
rmdir: failed to remove `parent': Device or resource busy
It's because cgroup_destroy_locked() (step 1 of destruction) leaves
cgroup on parent's children list, letting cgroup_offline_fn() (step 2 of
destruction) remove it; but step 2 is run by work queue, which may not
yet have removed the children when parent destruction checks the list.
Fix that by checking through a non-empty list of children: if every one
of them has already been marked CGRP_DEAD, then it's safe to proceed:
those children are invisible to userspace, and should not obstruct rmdir.
(I didn't see any reason to keep the cgrp->children checks under the
unrelated css_set_lock, so moved them out.)
tj: Flattened nested ifs a bit and updated comment so that it's
correct on both for-3.11-fixes and for-3.12.
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Tejun Heo [Wed, 28 Aug 2013 21:33:37 +0000 (17:33 -0400)]
workqueue: cond_resched() after processing each work item
If !PREEMPT, a kworker running work items back to back can hog CPU.
This becomes dangerous when a self-requeueing work item which is
waiting for something to happen races against stop_machine. Such
self-requeueing work item would requeue itself indefinitely hogging
the kworker and CPU it's running on while stop_machine would wait for
that CPU to enter stop_machine while preventing anything else from
happening on all other CPUs. The two would deadlock.
Jamie Liu reports that this deadlock scenario exists around
scsi_requeue_run_queue() and libata port multiplier support, where one
port may exclude command processing from other ports. With the right
timing, scsi_requeue_run_queue() can end up requeueing itself trying
to execute an IO which is asked to be retried while another device has
an exclusive access, which in turn can't make forward progress due to
stop_machine.
Fix it by invoking cond_resched() after executing each work item.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Jamie Liu <jamieliu@google.com>
References: http://thread.gmane.org/gmane.linux.kernel/1552567
Cc: stable@vger.kernel.org
--
kernel/workqueue.c | 9 +++++++++
1 file changed, 9 insertions(+)
Linus Torvalds [Thu, 29 Aug 2013 02:31:33 +0000 (19:31 -0700)]
Merge branch 'akpm' (patches from Andrew Morton)
Merge fixes from Andrew Morton:
"Five fixes.
err, make that six. let me try again"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
fs/ocfs2/super.c: Use bigger nodestr to accomodate 32-bit node numbers
memcg: check that kmem_cache has memcg_params before accessing it
drivers/base/memory.c: fix show_mem_removable() to handle missing sections
IPC: bugfix for msgrcv with msgtyp < 0
Omnikey Cardman 4000: pull in ioctl.h in user header
timer_list: correct the iterator for timer_list
Goldwyn Rodrigues [Wed, 28 Aug 2013 23:35:21 +0000 (16:35 -0700)]
fs/ocfs2/super.c: Use bigger nodestr to accomodate 32-bit node numbers
While using pacemaker/corosync, the node numbers are generated using IP
address as opposed to serial node number generation. This may not fit
in a 8-byte string. Use a bigger string to print the complete node
number.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Vagin [Wed, 28 Aug 2013 23:35:20 +0000 (16:35 -0700)]
memcg: check that kmem_cache has memcg_params before accessing it
If the system had a few memory groups and all of them were destroyed,
memcg_limited_groups_array_size has non-zero value, but all new caches
are created without memcg_params, because memcg_kmem_enabled() returns
false.
We try to enumirate child caches in a few places and all of them are
potentially dangerous.
For example my kernel is compiled with CONFIG_SLAB and it crashed when I
tryed to mount a NFS share after a few experiments with kmemcg.
BUG: unable to handle kernel NULL pointer dereference at
0000000000000008
IP: [<
ffffffff8118166a>] do_tune_cpucache+0x8a/0xd0
PGD
b942a067 PUD
b999f067 PMD 0
Oops: 0000 [#1] SMP
Modules linked in: fscache(+) ip6table_filter ip6_tables iptable_filter ip_tables i2c_piix4 pcspkr virtio_net virtio_balloon i2c_core floppy
CPU: 0 PID: 357 Comm: modprobe Not tainted 3.11.0-rc7+ #59
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
task:
ffff8800b9f98240 ti:
ffff8800ba32e000 task.ti:
ffff8800ba32e000
RIP: 0010:[<
ffffffff8118166a>] [<
ffffffff8118166a>] do_tune_cpucache+0x8a/0xd0
RSP: 0018:
ffff8800ba32fb70 EFLAGS:
00010246
RAX:
0000000000000000 RBX:
0000000000000000 RCX:
0000000000000006
RDX:
0000000000000000 RSI:
ffff8800b9f98910 RDI:
0000000000000246
RBP:
ffff8800ba32fba0 R08:
0000000000000002 R09:
0000000000000004
R10:
0000000000000001 R11:
0000000000000001 R12:
0000000000000010
R13:
0000000000000008 R14:
00000000000000d0 R15:
ffff8800375d0200
FS:
00007f55f1378740(0000) GS:
ffff8800bfa00000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
000000008005003b
CR2:
00007f24feba57a0 CR3:
0000000037b51000 CR4:
00000000000006f0
Call Trace:
enable_cpucache+0x49/0x100
setup_cpu_cache+0x215/0x280
__kmem_cache_create+0x2fa/0x450
kmem_cache_create_memcg+0x214/0x350
kmem_cache_create+0x2b/0x30
fscache_init+0x19b/0x230 [fscache]
do_one_initcall+0xfa/0x1b0
load_module+0x1c41/0x26d0
SyS_finit_module+0x86/0xb0
system_call_fastpath+0x16/0x1b
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: Glauber Costa <glommer@openvz.org>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Russ Anderson [Wed, 28 Aug 2013 23:35:18 +0000 (16:35 -0700)]
drivers/base/memory.c: fix show_mem_removable() to handle missing sections
"cat /sys/devices/system/memory/memory*/removable" crashed the system.
The problem is that show_mem_removable() is passing a
bad pfn to is_mem_section_removable(), which causes
if (!node_online(page_to_nid(page)))
to blow up. Why is it passing in a bad pfn?
The reason is that show_mem_removable() will loop sections_per_block
times. sections_per_block is 16, but mem->section_count is 8,
indicating holes in this memory block. Checking that the memory section
is present before checking to see if the memory section is removable
fixes the problem.
harp5-sys:~ # cat /sys/devices/system/memory/memory*/removable
0
1
1
1
1
1
1
1
1
1
1
1
1
1
BUG: unable to handle kernel paging request at
ffffea00c3200000
IP: [<
ffffffff81117ed1>] is_pageblock_removable_nolock+0x1/0x90
PGD
83ffd4067 PUD
37bdfce067 PMD 0
Oops: 0000 [#1] SMP
Modules linked in: autofs4 binfmt_misc rdma_ucm rdma_cm iw_cm ib_addr ib_srp scsi_transport_srp scsi_tgt ib_ipoib ib_cm ib_uverbs ib_umad iw_cxgb3 cxgb3 mdio mlx4_en mlx4_ib ib_sa mlx4_core ib_mthca ib_mad ib_core fuse nls_iso8859_1 nls_cp437 vfat fat joydev loop hid_generic usbhid hid hwperf(O) numatools(O) dm_mod iTCO_wdt ipv6 iTCO_vendor_support igb i2c_i801 ioatdma i2c_algo_bit ehci_pci pcspkr lpc_ich i2c_core ehci_hcd ptp sg mfd_core dca rtc_cmos pps_core mperf button xhci_hcd sd_mod crc_t10dif usbcore usb_common scsi_dh_emc scsi_dh_hp_sw scsi_dh_alua scsi_dh_rdac scsi_dh gru(O) xvma(O) xfs crc32c libcrc32c thermal sata_nv processor piix mptsas mptscsih scsi_transport_sas mptbase megaraid_sas fan thermal_sys hwmon ext3 jbd ata_piix ahci libahci libata scsi_mod
CPU: 4 PID: 5991 Comm: cat Tainted: G O 3.11.0-rc5-rja-uv+ #10
Hardware name: SGI UV2000/ROMLEY, BIOS SGI UV 2000/3000 series BIOS 01/15/2013
task:
ffff88081f034580 ti:
ffff880820022000 task.ti:
ffff880820022000
RIP: 0010:[<
ffffffff81117ed1>] [<
ffffffff81117ed1>] is_pageblock_removable_nolock+0x1/0x90
RSP: 0018:
ffff880820023df8 EFLAGS:
00010287
RAX:
0000000000040000 RBX:
ffffea00c3200000 RCX:
0000000000000004
RDX:
ffffea00c30b0000 RSI:
00000000001c0000 RDI:
ffffea00c3200000
RBP:
ffff880820023e38 R08:
0000000000000000 R09:
0000000000000001
R10:
0000000000000000 R11:
0000000000000001 R12:
ffffea00c33c0000
R13:
0000160000000000 R14:
6db6db6db6db6db7 R15:
0000000000000001
FS:
00007ffff7fb2700(0000) GS:
ffff88083fc80000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
ffffea00c3200000 CR3:
000000081b954000 CR4:
00000000000407e0
Call Trace:
show_mem_removable+0x41/0x70
dev_attr_show+0x2a/0x60
sysfs_read_file+0xf7/0x1c0
vfs_read+0xc8/0x130
SyS_read+0x5d/0xa0
system_call_fastpath+0x16/0x1b
Signed-off-by: Russ Anderson <rja@sgi.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Svenning Sørensen [Wed, 28 Aug 2013 23:35:17 +0000 (16:35 -0700)]
IPC: bugfix for msgrcv with msgtyp < 0
According to 'man msgrcv': "If msgtyp is less than 0, the first message of
the lowest type that is less than or equal to the absolute value of msgtyp
shall be received."
Bug: The kernel only returns a message if its type is 1; other messages
with type < abs(msgtype) will never get returned.
Fix: After having traversed the list to find the first message with the
lowest type, we need to actually return that message.
This regression was introduced by commit
daaf74cf0867 ("ipc: refactor
msg list search into separate function")
Signed-off-by: Svenning Soerensen <sss@secomea.dk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Frysinger [Wed, 28 Aug 2013 23:35:16 +0000 (16:35 -0700)]
Omnikey Cardman 4000: pull in ioctl.h in user header
This file uses the ioctl helpers (_IOR/_IOW/etc...), so include ioctl.h
for the definitions.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nathan Zimmer [Wed, 28 Aug 2013 23:35:14 +0000 (16:35 -0700)]
timer_list: correct the iterator for timer_list
Correct an issue with /proc/timer_list reported by Holger.
When reading from the proc file with a sufficiently small buffer, 2k so
not really that small, there was one could get hung trying to read the
file a chunk at a time.
The timer_list_start function failed to account for the possibility that
the offset was adjusted outside the timer_list_next.
Signed-off-by: Nathan Zimmer <nzimmer@sgi.com>
Reported-by: Holger Hans Peter Freyther <holger@freyther.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Berke Durak <berke.durak@xiphos.com>
Cc: Jeff Layton <jlayton@redhat.com>
Tested-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@vger.kernel.org> # 3.10.x
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Waiman Long [Thu, 29 Aug 2013 01:24:59 +0000 (18:24 -0700)]
vfs: make the dentry cache use the lockref infrastructure
This just replaces the dentry count/lock combination with the lockref
structure that contains both a count and a spinlock, and does the
mechanical conversion to use the lockref infrastructure.
There are no semantic changes here, it's purely syntactic. The
reference lockref implementation uses the spinlock exactly the same way
that the old dcache code did, and the bulk of this patch is just
expanding the internal "d_count" use in the dcache code to use
"d_lockref.count" instead.
This is purely preparation for the real change to make the reference
count updates be lockless during the 3.12 merge window.
[ As with the previous commit, this is a rewritten version of a concept
originally from Waiman, so credit goes to him, blame for any errors
goes to me.
Waiman's patch had some semantic differences for taking advantage of
the lockless update in dget_parent(), while this patch is
intentionally a pure search-and-replace change with no semantic
changes. - Linus ]
Signed-off-by: Waiman Long <Waiman.Long@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Waiman Long [Thu, 29 Aug 2013 01:13:26 +0000 (18:13 -0700)]
Add new lockref infrastructure reference implementation
This introduces a new "lockref" structure that supports the concept of
lockless updates of reference counts that still honor an attached
spinlock.
NOTE! This reference implementation is not the optimized lockless
version, rather it is the fallback implementation using standard
spinlocks. The actual optimized versions will be merged into 3.12, but
I wanted to get the infrastructure in place and document the new
interfaces.
[ Also note that this particular commit is drastically cut-down minimal
version of the original patch by Waiman. In order to properly credit
the original author I'm marking Waiman as the author here, but in the
end this patch bears little resemblance to the patch by Waiman. So
blame any errors on me editing things down to the point where I can
introduce the infrastructure before the merge window for 3.12 actually
opens. - Linus ]
Signed-off-by: Waiman Long <Waiman.Long@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Libo Chen [Mon, 26 Aug 2013 03:30:55 +0000 (11:30 +0800)]
net: xilinx: fix memleak
decrease device_node refcount np1 in err case.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rob Gardner [Sun, 25 Aug 2013 22:02:23 +0000 (16:02 -0600)]
net: usb: Add HP hs2434 device to ZLP exception table
This patch adds another entry (HP hs2434 Mobile Broadband) to the list
of exceptional devices that require a zero length packet in order to
function properly. This list was added in commit
844e88f0. The hs2434
is manufactured by Sierra Wireless, who also produces the MC7710,
which the ZLP exception list was created for in the first place. So
hopefully it is just this one producer's devices that will need this
workaround.
Tested on a DM1-4310NR HP notebook, which does not function without this
change.
Signed-off-by: Rob Gardner <robmatic@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliezer Tamir [Sun, 25 Aug 2013 07:23:46 +0000 (10:23 +0300)]
net: add cpu_relax to busy poll loop
Add a cpu_relaxt to sk_busy_loop.
Julie Cummings reported performance issues when hyperthreading is on.
Arjan van de Ven observed that we should have a cpu_relax() in the
busy poll loop.
Reported-by: Julie Cummings <julie.a.cummings@intel.com>
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Byungho An [Sat, 24 Aug 2013 06:31:43 +0000 (15:31 +0900)]
net: stmmac: fixed the pbl setting with DT
This patch fixed the pbl(programmable burst length) setting
using DT. Even though the default pbl is 8, If there is no
pbl property in device tree file, pbl is set 0 and it causes
bandwidth degradation.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pravin B Shelar [Fri, 23 Aug 2013 19:45:04 +0000 (12:45 -0700)]
genl: Hold reference on correct module while netlink-dump.
netlink dump operations take module as parameter to hold
reference for entire netlink dump duration.
Currently it holds ref only on genl module which is not correct
when we use ops registered to genl from another module.
Following patch adds module pointer to genl_ops so that netlink
can hold ref count on it.
CC: Jesse Gross <jesse@nicira.com>
CC: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pravin B Shelar [Fri, 23 Aug 2013 19:44:55 +0000 (12:44 -0700)]
genl: Fix genl dumpit() locking.
In case of genl-family with parallel ops off, dumpif() callback
is expected to run under genl_lock, But commit
def3117493eafd9df
(genl: Allow concurrent genl callbacks.) changed this behaviour
where only first dumpit() op was called under genl-lock.
For subsequent dump, only nlk->cb_lock was taken.
Following patch fixes it by defining locked dumpit() and done()
callback which takes care of genl-locking.
CC: Jesse Gross <jesse@nicira.com>
CC: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trond Myklebust [Wed, 28 Aug 2013 17:35:13 +0000 (13:35 -0400)]
SUNRPC: Fix memory corruption issue on 32-bit highmem systems
Some architectures, such as ARM-32 do not return the same base address
when you call kmap_atomic() twice on the same page.
This causes problems for the memmove() call in the XDR helper routine
"_shift_data_right_pages()", since it defeats the detection of
overlapping memory ranges, and has been seen to corrupt memory.
The fix is to distinguish between the case where we're doing an
inter-page copy or not. In the former case of we know that the memory
ranges cannot possibly overlap, so we can additionally micro-optimise
by replacing memmove() with memcpy().
Reported-by: Mark Young <MYoung@nvidia.com>
Reported-by: Matt Craighead <mcraighead@nvidia.com>
Cc: Bruce Fields <bfields@fieldses.org>
Cc: stable@vger.kernel.org
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Tested-by: Matt Craighead <mcraighead@nvidia.com>
Linus Torvalds [Wed, 28 Aug 2013 16:18:05 +0000 (09:18 -0700)]
Revert "fs: Allow unprivileged linkat(..., AT_EMPTY_PATH) aka flink"
This reverts commit
bb2314b47996491bbc5add73633905c3120b6268.
It wasn't necessarily wrong per se, but we're still busily discussing
the exact details of this all, so I'm going to revert it for now.
It's true that you can already do flink() through /proc and that flink()
isn't new. But as Brad Spengler points out, some secure environments do
not mount proc, and flink adds a new interface that can avoid path
lookup of the source for those kinds of environments.
We may re-do this (and even mark it for stable backporting back in 3.11
and possibly earlier) once the whole discussion about the interface is done.
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Brad Spengler <spender@grsecurity.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Steffen Klassert [Wed, 28 Aug 2013 06:47:14 +0000 (08:47 +0200)]
xfrm: Fix potential null pointer dereference in xdst_queue_output
The net_device might be not set on the skb when we try refcounting.
This leads to a null pointer dereference in xdst_queue_output().
It turned out that the refcount to the net_device is not needed
after all. The dst_entry has a refcount to the net_device before
we queue the skb, so it can't go away. Therefore we can remove the
refcount on queueing to fix the null pointer dereference.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Takashi Iwai [Tue, 27 Aug 2013 10:03:01 +0000 (12:03 +0200)]
ALSA: opti9xx: Fix conflicting driver object name
The recent commit to delay the release of kobject triggered NULL
dereferences of opti9xx drivers. The cause is that all
snd-opti92x-ad1848, snd-opti92x-cs4231 and snd-opti93x drivers
register the PnP card driver with the very same name, and also
snd-opti92x-ad1848 and -cs4231 drivers register the ISA driver with
the same name, too. When these drivers are built in, quick
"register-release-and-re-register" actions occur, and this results in
Oops because of the same name is assigned to the kobject.
The fix is simply to assign individual names. As a bonus, by using
KBUILD_MODNAME, the patch reduces more lines than it adds.
The fix is based on the suggestion by Russell King.
Reported-and-tested-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Ariel Elior [Tue, 27 Aug 2013 22:13:04 +0000 (01:13 +0300)]
bnx2x: Fix VF stats sync
Since the PF gathers statistics for the VF, when the VF is about to unload
we must synchronize the release of its statistics buffer with the PF, so that
no DMA operation will be made to that address after the buffer release.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ariel Elior [Tue, 27 Aug 2013 22:13:03 +0000 (01:13 +0300)]
bnx2x: Fix VF memory leak unload
Due to incorrect VF/PF conditions, when unloading a VF it will not release
part of the memory it has previously allocated.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ariel Elior [Tue, 27 Aug 2013 22:13:02 +0000 (01:13 +0300)]
bnx2x: Fix functionality of configuring vlan list
The check on return code of bnx2x_vfop_config_vlan0() would lead to error
handling flow as the return value indicating an existing pending ramrod would
be erroneously considered as an error.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Tue, 27 Aug 2013 22:13:01 +0000 (01:13 +0300)]
bnx2x: Fix move FP memory deallocations
If driver will fail to allocate all queues, it will shrink the number of
queues and move the storage queue to its correct place (i.e., the last
queue among the newly supported number).
When changing the pointers of the new location of the FCoE queue, we need
to pay special attention to the aggregations pointer - that memory is allocated
during probe and released upon driver removal. Current implementation has 2
pointers pointing to the same chunk of allocated memory, meaning upon removal
there will be two kfree() of the same chunk while the other won't be released.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ariel Elior [Tue, 27 Aug 2013 22:13:00 +0000 (01:13 +0300)]
bnx2x: vf mark stats started
Solve issue where no stats were being collected for VF devices due to missing
configuration in the stats' atomic synchronization mechanism.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 27 Aug 2013 19:54:47 +0000 (15:54 -0400)]
Merge branch 'for-davem' of git://git./linux/kernel/git/linville/wireless
John W. Linville says:
====================
This is one more set of fixes intended for the 3.11 stream...
For the mac80211 bits, Johannes says:
"I have three more patches for the 3.11 stream: Felix's fix for the
fairly visible brcmsmac crash, a fix from Simon for an IBSS join bug I
found and a fix for a channel context bug in IBSS I'd introduced."
Along with those...
Sujith Manoharan makes a minor change to not use a PLL hang workaroun
for AR9550. This one-liner fixes a couple of bugs reported in the Red Hat
bugzilla.
Helmut Schaa addresses an ath9k_htc bug that mangles frame headers
during Tx. This fix is small, tested by the bug reported and isolated
to ath9k_htc.
Stanislaw Gruszka reverts a recent iwl4965 change that broke rfkill
notification to user space.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Schmidt [Fri, 23 Aug 2013 13:41:19 +0000 (15:41 +0200)]
ps3_gelic: lower NAPI weight
Since commit
82dc3c63 ("net: introduce NAPI_POLL_WEIGHT")
netif_napi_add() produces an error message if a NAPI poll weight
greater than 64 is requested.
GELIC_NET_NAPI_WEIGHT is defined to GELIC_NET_RX_DESCRIPTORS,
which is 128.
Use the standard NAPI weight.
v2: proper reference to the related commit
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Schmidt [Fri, 23 Aug 2013 13:41:09 +0000 (15:41 +0200)]
netxen: lower NAPI weight
Since commit
82dc3c63 ("net: introduce NAPI_POLL_WEIGHT")
netif_napi_add() produces an error message if a NAPI poll weight
greater than 64 is requested.
Use the standard NAPI weight.
v2: proper reference to the related commit
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Schmidt [Fri, 23 Aug 2013 13:40:53 +0000 (15:40 +0200)]
jme: lower NAPI weight
Since commit
82dc3c63 ("net: introduce NAPI_POLL_WEIGHT")
netif_napi_add() produces an error message if a NAPI poll weight
greater than 64 is requested.
jme requests a quarter of the rx ring size as the NAPI weight.
jme's rx ring size is 1 << 9 = 512.
Use the standard NAPI weight.
v2: proper reference to the related commit
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Lutomirski [Thu, 22 Aug 2013 18:39:16 +0000 (11:39 -0700)]
Rename nsproxy.pid_ns to nsproxy.pid_ns_for_children
nsproxy.pid_ns is *not* the task's pid namespace. The name should clarify
that.
This makes it more obvious that setns on a pid namespace is weird --
it won't change the pid namespace shown in procfs.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Lutomirski [Thu, 22 Aug 2013 18:39:15 +0000 (11:39 -0700)]
net: Check the correct namespace when spoofing pid over SCM_RIGHTS
This is a security bug.
The follow-up will fix nsproxy to discourage this type of issue from
happening again.
Cc: stable@vger.kernel.org
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 27 Aug 2013 17:10:30 +0000 (10:10 -0700)]
Merge tag 'regmap-v3.11-rc7' of git://git./linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"Two changes here:
- Fix a bug in the rbtree code which could cause it to create two
different cache entries for the same register by adding a single
register at a time to the cache. This isn't awesome for
performance but it's non-invasive which we need for this late in
the release cycle and the I/O costs we're trying to avoid are high.
- Add another header used in the !CONFIG_REGMAP stubs where we had
been relying on implicit inclusion"
* tag 'regmap-v3.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: rbtree: Fix overlapping rbnodes.
regmap: Add another missing header for !CONFIG_REGMAP stubs
Linus Torvalds [Tue, 27 Aug 2013 17:09:22 +0000 (10:09 -0700)]
Merge branch 'merge' of git://git./linux/kernel/git/benh/powerpc
Pull powerpc fixes from Ben Herrenschmidt:
"Here are 3 bug fixes that should probably go into 3.11 since I'm also
tagging them for stable.
Once fixes our old /proc/powerpc/lparcfg file which provides partition
informations when running under our hypervisor and also acts as a
user-triggerable Oops when hot :-(
The other two respectively are a one liner to fix a HVSI protocol
handshake problem causing the console to fail to show up on a bunch of
machines until we reach userspace, which I deem annoying enough to
warrant going to stable, and a nasty gcc miscompile causing us to pass
virtual instead of physical addresses to the firmware under some
circumstances"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/hvsi: Increase handshake timeout from 200ms to 400ms.
powerpc: Work around gcc miscompilation of __pa() on 64-bit
powerpc: Don't Oops when accessing /proc/powerpc/lparcfg without hypervisor
Cyrill Gorcunov [Tue, 27 Aug 2013 08:37:18 +0000 (12:37 +0400)]
mm: move_ptes -- Set soft dirty bit depending on pte type
Dave reported corrupted swap entries
| [ 4588.541886] swap_free: Unused swap offset entry
00002d15
| [ 4588.541952] BUG: Bad page map in process trinity-kid12 pte:
005a2a80 pmd:
22c01f067
and Hugh pointed that in move_ptes _PAGE_SOFT_DIRTY bit set regardless
the type of entry pte consists of. The trick here is that when we carry
soft dirty status in swap entries we are to use _PAGE_SWP_SOFT_DIRTY
instead, because this is the only place in pte which can be used for own
needs without intersecting with bits owned by swap entry type/offset.
Reported-and-tested-by: Dave Jones <davej@redhat.com>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Pavel Emelyanov <xemul@parallels.com>
Analyzed-by: Hugh Dickins <hughd@google.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eugene Surovegin [Mon, 26 Aug 2013 18:53:32 +0000 (11:53 -0700)]
powerpc/hvsi: Increase handshake timeout from 200ms to 400ms.
This solves a problem observed in kexec'ed kernel where 200ms timeout is
too short and bootconsole fails to initialize. Console did eventually
become workable but much later into the boot process.
Observed timeout was around 260ms, but I decided to make it a little bigger
for more reliability.
This has been tested on Power7 machine with Petitboot as a primary
bootloader and PowerNV firmware.
CC: <stable@vger.kernel.org>
Signed-off-by: Eugene Surovegin <surovegin@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Paul Mackerras [Tue, 27 Aug 2013 06:07:49 +0000 (16:07 +1000)]
powerpc: Work around gcc miscompilation of __pa() on 64-bit
On 64-bit, __pa(&static_var) gets miscompiled by recent versions of
gcc as something like:
addis 3,2,.LANCHOR1+
4611686018427387904@toc@ha
addi 3,3,.LANCHOR1+
4611686018427387904@toc@l
This ends up effectively ignoring the offset, since its bottom 32 bits
are zero, and means that the result of __pa() still has 0xC in the top
nibble. This happens with gcc 4.8.1, at least.
To work around this, for 64-bit we make __pa() use an AND operator,
and for symmetry, we make __va() use an OR operator. Using an AND
operator rather than a subtraction ends up with slightly shorter code
since it can be done with a single clrldi instruction, whereas it
takes three instructions to form the constant (-PAGE_OFFSET) and add
it on. (Note that MEMORY_START is always 0 on 64-bit.)
CC: <stable@vger.kernel.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Benjamin Herrenschmidt [Tue, 27 Aug 2013 06:38:33 +0000 (16:38 +1000)]
powerpc: Don't Oops when accessing /proc/powerpc/lparcfg without hypervisor
/proc/powerpc/lparcfg is an ancient facility (though still actively used)
which allows access to some informations relative to the partition when
running underneath a PAPR compliant hypervisor.
It makes no sense on non-pseries machines. However, currently, not only
can it be created on these if the kernel has pseries support, but accessing
it on such a machine will crash due to trying to do hypervisor calls.
In fact, it should also not do HV calls on older pseries that didn't have
an hypervisor either.
Finally, it has the plumbing to be a module but is a "bool" Kconfig option.
This fixes the whole lot by turning it into a machine_device_initcall
that is only created on pseries, and adding the necessary hypervisor
check before calling the H_GET_EM_PARMS hypercall
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Linus Torvalds [Tue, 27 Aug 2013 02:23:29 +0000 (19:23 -0700)]
Merge tag 'usb-3.11-rc8' of git://git./linux/kernel/git/gregkh/usb
Pull USB bugfix from Greg KH:
"Here is a single bugfix that resolves the "can not build the OHCI
driver with CONFIG_PM disabled" problem that lots of people have been
reporting with 3.11-rc7. Sorry about that one, it missed my build
tests, and it seems, a number of others as well.
Thank goodness for Guenter :)"
* tag 'usb-3.11-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: OHCI: fix build error related to ohci_suspend/resume
Linus Torvalds [Tue, 27 Aug 2013 02:22:49 +0000 (19:22 -0700)]
Merge tag 'jfs-3.11-rc8' of git://github.com/kleikamp/linux-shaggy
Pull jfs fix from Dave Kleikamp:
"One JFS patch to fix an incompatibility with NFSv4 resulting in the
nfs client reporting a readdir loop"
* tag 'jfs-3.11-rc8' of git://github.com/kleikamp/linux-shaggy:
jfs: fix readdir cookie incompatibility with NFSv4
Alan Stern [Mon, 26 Aug 2013 14:53:53 +0000 (10:53 -0400)]
USB: OHCI: fix build error related to ohci_suspend/resume
Commit
9a11899c5e69 (USB: OHCI: add missing PCI PM callbacks to
ohci-pci.c) added missing ohci_suspend and ohci_resume callback
pointers, but forgot that these callbacks are declared and defined
only when CONFIG_PM is enabled.
This patch adds a preprocessor conditional to avoid build errors when
PM is disabled.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Meelis Roos <mroos@linux.ee>,
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sarveshwar Bandi [Fri, 23 Aug 2013 09:29:33 +0000 (14:59 +0530)]
be2net: Check for POST state in suspend-resume sequence
In suspend-resume sequence, the OS could attempt to initialize the controller
before it is ready, check for POST state before going ahead.
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hannes Frederic Sowa [Mon, 26 Aug 2013 10:31:23 +0000 (12:31 +0200)]
ipv6: set skb->protocol on tcp, raw and ip6_append_data genereated skbs
Currently we don't initialize skb->protocol when transmitting data via
tcp, raw(with and without inclhdr) or udp+ufo or appending data directly
to the socket transmit queue (via ip6_append_data). This needs to be
done so that we can get the correct mtu in the xfrm layer.
Setting of skb->protocol happens only in functions where we also have
a transmitting socket and a new skb, so we don't overwrite old values.
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Hannes Frederic Sowa [Mon, 26 Aug 2013 10:31:19 +0000 (12:31 +0200)]
xfrm: revert ipv4 mtu determination to dst_mtu
In commit
0ea9d5e3e0e03a63b11392f5613378977dae7eca ("xfrm: introduce
helper for safe determination of mtu") I switched the determination of
ipv4 mtus from dst_mtu to ip_skb_dst_mtu. This was an error because in
case of IP_PMTUDISC_PROBE we fall back to the interface mtu, which is
never correct for ipv4 ipsec.
This patch partly reverts
0ea9d5e3e0e03a63b11392f5613378977dae7eca
("xfrm: introduce helper for safe determination of mtu").
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Mag [Mon, 26 Aug 2013 07:22:01 +0000 (00:22 -0700)]
Input: xpad - add signature for Razer Onza Classic Edition
Signed-off-by: Nol "Mag" Archinova <magissia@magissia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Linus Torvalds [Mon, 26 Aug 2013 00:43:22 +0000 (17:43 -0700)]
Linux 3.11-rc7
Linus Torvalds [Sun, 25 Aug 2013 19:44:15 +0000 (12:44 -0700)]
Merge tag 'staging-3.11-rc7' of git://git./linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are two tiny staging tree fixes (well, one is for an iio driver,
but those updates come through the staging tree due to dependancies)
One fixes a problem with an IIO driver, and the other fixes a bug in
the comedi driver core"
* tag 'staging-3.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: comedi: bug-fix NULL pointer dereference on failed attach
iio: adjd_s311: Fix non-scan mode data read
Linus Torvalds [Sun, 25 Aug 2013 19:43:44 +0000 (12:43 -0700)]
Merge tag 'usb-3.11-rc7' of git://git./linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are two USB fixes for 3.11-rc7
One fixes a reported regression in the OHCI driver, and the other
fixes a reported build breakage in the USB phy drivers"
* tag 'usb-3.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: phy: fix build breakage
USB: OHCI: add missing PCI PM callbacks to ohci-pci.c
Linus Torvalds [Sun, 25 Aug 2013 19:41:37 +0000 (12:41 -0700)]
Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-arm
Pull ARM fixes from Russell King:
"This round of fixes is smaller than previous: a couple more updates
for the security fixes, and a one-liner kexec fix"
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7816/1: CONFIG_KUSER_HELPERS: fix help text
ARM: 7815/1: kexec: offline non panic CPUs on Kdump panic
ARM: 7819/1: fiq: Cast the first argument of flush_icache_range()
Linus Torvalds [Sun, 25 Aug 2013 19:25:38 +0000 (12:25 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"Assorted fixes from the last week or so"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
VFS: collect_mounts() should return an ERR_PTR
bfs: iget_locked() doesn't return an ERR_PTR
efs: iget_locked() doesn't return an ERR_PTR()
proc: kill the extra proc_readfd_common()->dir_emit_dots()
cope with potentially long ->d_dname() output for shmem/hugetlb
Matteo Delfino [Thu, 15 Aug 2013 07:09:41 +0000 (00:09 -0700)]
Input: elantech - fix packet check for v3 and v4 hardware
The signatures of v3 and v4 packets change depending on the value of a
hardware flag called 'crc_enabled'. The packet type detection must change
accordingly.
This patch also restores a consistency check for v4 packets inadvertently
removed by commit:
9eebed7de660c0b5ab129a9de4f89d20b60de68c
Input: elantech - fix for newer hardware versions (v7)
A note about the naming convention: v3 hardware is associated with IC body
v5 while v4 hardware is associated with IC body v6 and v7. The above commit
refers to IC body v7, not to v7 hardware.
Tested on Samsung NP730U3E (fw = 0x675f05, ICv7, crc_enabled = 1)
Tested-by: Giovanni Frigione <gio.frigione@gmail.com>
Signed-off-by: Matteo Delfino <kendatsuba@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Ping Cheng [Wed, 21 Aug 2013 16:14:49 +0000 (09:14 -0700)]
Input: wacom - add support for 0x300 and 0x301
Tested-by: Arjuna Rao Chavala <arjunaraoc@gmail.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Linus Torvalds [Sat, 24 Aug 2013 18:34:33 +0000 (11:34 -0700)]
Merge tag 'acpi-3.11-rc7' of git://git./linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"I really hoped that it wouldn't be necessary to change anything in
ACPI at this point, but it turns out that we need to revert one more
ACPI video commit causing trouble.
This reverts a change in the ACPI video driver that caused the ACPI
backlight initialization to be carried out even if acpi_backlight=vendor
is passed in the kernel command line which turns out to break things
at least on one system"
* tag 'acpi-3.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "ACPI / video: Always call acpi_video_init_brightness() on init"
Linus Torvalds [Sat, 24 Aug 2013 18:33:21 +0000 (11:33 -0700)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of small bug fixes for lpfc and zfcp and a fix for a
fairly nasty bug in sg where a process which cancels I/O completes in
a kernel thread which would then try to write back to the now gone
userspace and end up writing to a random kernel address instead"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] zfcp: remove access control tables interface (keep sysfs files)
[SCSI] zfcp: fix schedule-inside-lock in scsi_device list loops
[SCSI] zfcp: fix lock imbalance by reworking request queue locking
[SCSI] sg: Fix user memory corruption when SG_IO is interrupted by a signal
[SCSI] lpfc: Don't force CONFIG_GENERIC_CSUM on
Joern Rennecke [Sat, 24 Aug 2013 06:33:06 +0000 (12:03 +0530)]
ARC: [lib] strchr breakage in Big-endian configuration
For a search buffer, 2 byte aligned, strchr() was returning pointer
outside of buffer (buf - 1)
------------->8----------------
// Input buffer (default 4 byte aigned)
char *buffer = "1AA_";
// actual search start (to mimick 2 byte alignment)
char *current_line = &(buffer[2]);
// Character to search for
char c = 'A';
char *c_pos = strchr(current_line, c);
printf("%s\n", c_pos) --> 'AA_' as oppose to 'A_'
------------->8----------------
Reported-by: Anton Kolesov <Anton.Kolesov@synopsys.com>
Debugged-by: Anton Kolesov <Anton.Kolesov@synopsys.com>
Cc: <stable@vger.kernel.org> # [3.9 and 3.10]
Cc: Noam Camus <noamc@ezchip.com>
Signed-off-by: Joern Rennecke <joern.rennecke@embecosm.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan Carpenter [Wed, 14 Aug 2013 09:44:39 +0000 (12:44 +0300)]
VFS: collect_mounts() should return an ERR_PTR
This should actually be returning an ERR_PTR on error instead of NULL.
That was how it was designed and all the callers expect it.
[AV: actually, that's what "VFS: Make clone_mnt()/copy_tree()/collect_mounts()
return errors" missed - originally collect_mounts() was expected to return
NULL on failure]
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Dan Carpenter [Wed, 14 Aug 2013 09:51:03 +0000 (12:51 +0300)]
bfs: iget_locked() doesn't return an ERR_PTR
iget_locked() returns a NULL on error, it doesn't return an ERR_PTR.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Dan Carpenter [Wed, 14 Aug 2013 09:49:40 +0000 (12:49 +0300)]
efs: iget_locked() doesn't return an ERR_PTR()
The iget_locked() function returns NULL on error and never an ERR_PTR.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Oleg Nesterov [Sat, 24 Aug 2013 15:14:34 +0000 (17:14 +0200)]
proc: kill the extra proc_readfd_common()->dir_emit_dots()
proc_readfd_common() does dir_emit_dots() twice in a row,
we need to do this only once.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Sat, 24 Aug 2013 16:08:17 +0000 (12:08 -0400)]
cope with potentially long ->d_dname() output for shmem/hugetlb
dynamic_dname() is both too much and too little for those - the
output may be well in excess of 64 bytes dynamic_dname() assumes
to be enough (thanks to ashmem feeding really long names to
shmem_file_setup()) and vsnprintf() is an overkill for those
guys.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds [Fri, 23 Aug 2013 17:59:42 +0000 (10:59 -0700)]
Merge branch 'for-3.11-fixes' of git://git./linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"This contains three commits all of which are updates for specific
devices which aren't too widespread. Pretty limited scope and nothing
too interesting or dangerous"
* 'for-3.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
sata_fsl: save irqs while coalescing
libata: apply behavioral quirks to sil3826 PMP
sata, highbank: fix ordering of SGPIO signals
Linus Torvalds [Fri, 23 Aug 2013 17:58:50 +0000 (10:58 -0700)]
Merge branch 'for-3.11-fixes' of git://git./linux/kernel/git/tj/cgroup
Pull cgroup fix from Tejun Heo:
"A late fix for cgroup.
This fixes a behavior regression visible to userland which was created
by a commit merged during -rc1. While the behavior change isn't too
likely to be noticeable, the fix is relatively low risk and we'll need
to backport it through -stable anyway if the bug gets released"
* 'for-3.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cpuset: fix a regression in validating config change
Linus Torvalds [Fri, 23 Aug 2013 17:46:28 +0000 (10:46 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Ben was on holidays for a week so a few nouveau regression fixes
backed up, but they all seem necessary.
Otherwise one i915 and one gma500 fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
gma500: Fix SDVO turning off randomly
drm/nv04/disp: fix framebuffer pin refcounting
drm/nouveau/mc: fix race condition between constructor and request_irq()
drm/nouveau: fix reclocking on nv40
drm/nouveau/ltcg: fix allocating memory as free
drm/nouveau/ltcg: fix ltcg memory initialization after suspend
drm/nouveau/fb: fix null derefs in nv49 and nv4e init
drm/i915: Invalidate TLBs for the rings after a reset
Anatolij Gustschin [Wed, 21 Aug 2013 15:43:31 +0000 (17:43 +0200)]
usb: phy: fix build breakage
Commit
94ae9843 (usb: phy: rename all phy drivers to phy-$name-usb.c)
renamed drivers/usb/phy/otg_fsm.h to drivers/usb/phy/phy-fsm-usb.h
but changed drivers/usb/phy/phy-fsm-usb.c to include not existing
"phy-otg-fsm.h" instead of new "phy-fsm-usb.h". This breaks building:
...
drivers/usb/phy/phy-fsm-usb.c:32:25: fatal error: phy-otg-fsm.h: No such file or directory
compilation terminated.
make[3]: *** [drivers/usb/phy/phy-fsm-usb.o] Error 1
This commit also missed to modify drivers/usb/phy/phy-fsl-usb.h
to include new "phy-fsm-usb.h" instead of "otg_fsm.h" resulting
in another build breakage:
...
In file included from drivers/usb/phy/phy-fsl-usb.c:46:0:
drivers/usb/phy/phy-fsl-usb.h:18:21: fatal error: otg_fsm.h: No such file or directory
compilation terminated.
make[3]: *** [drivers/usb/phy/phy-fsl-usb.o] Error 1
Fix both issues.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: stable <stable@vger.kernel.org> # 3.10+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Wed, 21 Aug 2013 14:33:17 +0000 (10:33 -0400)]
USB: OHCI: add missing PCI PM callbacks to ohci-pci.c
Commit
c1117afb8589 (USB: OHCI: make ohci-pci a separate driver)
neglected to preserve the entries for the pci_suspend and pci_resume
driver callbacks. As a result, OHCI controllers don't work properly
during suspend and after hibernation.
This patch adds the missing callbacks to the driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Steve Cotton <steve@s.cotton.clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ian Abbott [Fri, 23 Aug 2013 11:37:17 +0000 (12:37 +0100)]
staging: comedi: bug-fix NULL pointer dereference on failed attach
Commit
dcd7b8bd63cb81c5b973bf86510ca3c80bbbd162 ("staging: comedi: put
module _after_ detach" by myself) reversed a couple of calls in
`comedi_device_attach()` when recovering from an error returned by the
low-level driver's 'attach' handler. Unfortunately, that introduced a
NULL pointer dereference bug as `dev->driver` is NULL after the call to
`comedi_device_detach()`. We still have a pointer to the low-level
comedi driver structure in the `driv` variable, so use that instead.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Fri, 23 Aug 2013 16:54:21 +0000 (09:54 -0700)]
Merge git://git./linux/kernel/git/davem/net
Merge networking fixes from David Miller:
1) Revert Johannes Berg's genetlink locking fix, because it causes
regressions.
Johannes and Pravin Shelar are working on fixing things properly.
2) Do not drop ipv6 ICMP messages without a redirected header option,
they are legal. From Duan Jiong.
3) Missing error return propagation in probing of via-ircc driver.
From Alexey Khoroshilov.
4) Do not clear out broadcast/multicast/unicast/WOL bits in r8169 when
initializing, from Peter Wu.
5) realtek phy driver programs wrong interrupt status bit, from
Giuseppe CAVALLARO.
6) Fix statistics regression in AF_PACKET code, from Willem de Bruijn.
7) Bridge code uses wrong bitmap length, from Toshiaki Makita.
8) SFC driver uses wrong indexes to look up MAC filters, from Ben
Hutchings.
9) Don't pass stack buffers into usb control operations in hso driver,
from Daniel Gimpelevich.
10) Multiple ipv6 fragmentation headers in one packet is illegal and
such packets should be dropped, from Hannes Frederic Sowa.
11) When TCP sockets are "repaired" as part of checkpoint/restart, the
timestamp field of SKBs need to be refreshed otherwise RTOs can be
wildly off. From Andrey Vagin.
12) Fix memcpy args (uses 'address of pointer' instead of 'pointer') in
hostp driver. From Dan Carpenter.
13) nl80211hdr_put() doesn't return an ERR_PTR, but some code believes
it does. From Dan Carpenter.
14) Fix regression in wireless SME disconnects, from Johannes Berg.
15) Don't use a stack buffer for DMA in zd1201 USB wireless driver, from
Jussi Kivilinna.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits)
ipv4: expose IPV4_DEVCONF
ipv6: handle Redirect ICMP Message with no Redirected Header option
be2net: fix disabling TX in be_close()
Revert "genetlink: fix family dump race"
hso: Fix stack corruption on some architectures
hso: Earlier catch of error condition
sfc: Fix lookup of default RX MAC filters when steered using ethtool
bridge: Use the correct bit length for bitmap functions in the VLAN code
packet: restore packet statistics tp_packets to include drops
net: phy: rtl8211: fix interrupt on status link change
r8169: remember WOL preferences on driver load
via-ircc: don't return zero if via_ircc_open() failed
macvtap: Ignore tap features when VNET_HDR is off
macvtap: Correctly set tap features when IFF_VNET_HDR is disabled.
macvtap: simplify usage of tap_features
tcp: set timestamps for restored skb-s
bnx2x: set VF DMAE when first function has 0 supported VFs
bnx2x: Protect against VFs' ndos when SR-IOV is disabled
bnx2x: prevent VF benign attentions
bnx2x: Consider DCBX remote error
...
Linus Torvalds [Fri, 23 Aug 2013 16:52:32 +0000 (09:52 -0700)]
Merge branch 'akpm' (patches from Andrew Morton)
Merge fixes from Andrew Morton:
"A few fixes. One is a licensing change and I don't do licensing, so
please eyeball that one"
Licensing eye-balled.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
lib/lz4: correct the LZ4 license
memcg: get rid of swapaccount leftovers
nilfs2: fix issue with counting number of bio requests for BIO_EOPNOTSUPP error detection
nilfs2: remove double bio_put() in nilfs_end_bio_write() for BIO_EOPNOTSUPP error
drivers/platform/olpc/olpc-ec.c: initialise earlier
Richard Laager [Thu, 22 Aug 2013 23:35:47 +0000 (16:35 -0700)]
lib/lz4: correct the LZ4 license
The LZ4 code is listed as using the "BSD 2-Clause License".
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Acked-by: Kyungsik Lee <kyungsik.lee@lge.com>
Cc: Chanho Min <chanho.min@lge.com>
Cc: Richard Yao <ryao@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ The 2-clause BSD can be just converted into GPL, but that's rude and
pointless, so don't do it - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Thu, 22 Aug 2013 23:35:46 +0000 (16:35 -0700)]
memcg: get rid of swapaccount leftovers
The swapaccount kernel parameter without any values has been removed by
commit
a2c8990aed5a ("memsw: remove noswapaccount kernel parameter") but
it seems that we didn't get rid of all the left overs.
Make sure that menuconfig help text and kernel-parameters.txt are clear
about value for the paramter and remove the stalled comment which is not
very much useful on its own.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Reported-by: Gergely Risko <gergely@risko.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vyacheslav Dubeyko [Thu, 22 Aug 2013 23:35:45 +0000 (16:35 -0700)]
nilfs2: fix issue with counting number of bio requests for BIO_EOPNOTSUPP error detection
Fix the issue with improper counting number of flying bio requests for
BIO_EOPNOTSUPP error detection case.
The sb_nbio must be incremented exactly the same number of times as
complete() function was called (or will be called) because
nilfs_segbuf_wait() will call wail_for_completion() for the number of
times set to sb_nbio:
do {
wait_for_completion(&segbuf->sb_bio_event);
} while (--segbuf->sb_nbio > 0);
Two functions complete() and wait_for_completion() must be called the
same number of times for the same sb_bio_event. Otherwise,
wait_for_completion() will hang or leak.
Signed-off-by: Vyacheslav Dubeyko <slava@dubeyko.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Tested-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>