review.tizen.org Git - platform/kernel/linux-starfive.git/log

Merge tag 'thermal-v6.5-rc1' of ssh://gitolite./linux/kernel/git/thermal/linux into thermal

Pull thermal control updates for 6.5-rc1 from Daniel Lezcano:

"- Add DT bindings for SM6375, MSM8226 and QCM2290 Qcom platforms (Konrad
   Dybcio)

- Add DT bindings and support for QCom MSM8226 (Matti Lehtimäki)

- Add DT bindings for QCom ipq9574 (Praveenkumar I)

- Convert bcm2835 DT bindings to the yaml schema (Stefan Wahren)

- Allow selecting the bang-bang governor as default (Thierry Reding)

- Refactor and prepare the code to set the scene for RCar Gen4
   (Wolfram Sang)

- Cleanup and fixes for the QCom tsens drivers. Add DT bindings and
   calibration for the MSM8909 platform (Stephan Gerhold)

- Revert a patch introducing a wrong usage of devm_of_iomap() on the
   Mediatek platform (Ricardo Cañuelo)

- Fix the clock vs reset ordering in order to conform to the
   documentation on the sun8i (Christophe JAILLET)

- Prevent setting up undocumented registers, enable the only described
   sensors and add the version 2.1 on the Qoriq sensor (Peng Fan)

- Add DT bindings and support for the Armada AP807 (Alex Leibovich)

- Update the mlx5 driver with the recent thermal changes (Daniel
   Lezcano)

- Convert to platform remove callback returning void on STM32 (Uwe
   Kleine-König)

- Add an error information printing for devm_thermal_add_hwmon_sysfs()
   and remove the error from the Sun8i, Amlogic, i.MX, TI, K3, Tegra,
   Qoriq, Mediateka and QCom (Yangtao Li)

- Register as hwmon sensor for the Generic ADC (Chen-Yu Tsai)

- Use the dev_err_probe() function in the QCom tsens alarm driver
   (Luca Weiss)"

* tag 'thermal-v6.5-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (38 commits)
  thermal/drivers/qcom/temp-alarm: Use dev_err_probe
  thermal/drivers/generic-adc: Register thermal zones as hwmon sensors
  thermal/drivers/mediatek/lvts_thermal: Remove redundant msg in lvts_ctrl_start()
  thermal/drivers/qcom: Remove redundant msg at probe time
  thermal/drivers/ti-soc: Remove redundant msg in ti_thermal_expose_sensor()
  thermal/drivers/qoriq: Remove redundant msg in qoriq_tmu_register_tmu_zone()
  thermal/drivers/tegra: Remove redundant msg in tegra_tsensor_register_channel()
  drivers/thermal/k3: Remove redundant msg in k3_bandgap_probe()
  thermal/drivers/imx: Remove redundant msg in imx8mm_tmu_probe() and imx_sc_thermal_probe()
  thermal/drivers/amlogic: Remove redundant msg in amlogic_thermal_probe()
  thermal/drivers/sun8i: Remove redundant msg in sun8i_ths_register()
  thermal/hwmon: Add error information printing for devm_thermal_add_hwmon_sysfs()
  thermal/drivers/stm32: Convert to platform remove callback returning void
  net/mlx5: Update the driver with the recent thermal changes
  thermal/drivers/armada: Add support for AP807 thermal data
  dt-bindings: armada-thermal: Add armada-ap807-thermal compatible
  thermal/drivers/qoriq: Support version 2.1
  thermal/drivers/qoriq: Only enable supported sensors
  thermal/drivers/qoriq: No need to program site adjustment register
  thermal/drivers/mediatek/lvts_thermal: Register thermal zones as hwmon sensors
  ...

Merge back earlier Intel thermal control material for 6.5.

thermal/drivers/qcom/temp-alarm: Use dev_err_probe

Use the dev_err_probe function instead of dev_err in the probe function
so that the printed message includes the return value and also handles
-EPROBE_DEFER nicely.

Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230625-spmi-temp-alarm-defer-v1-1-2d57acf36855@z3ntu.xyz

thermal/drivers/generic-adc: Register thermal zones as hwmon sensors

Register thermal zones as hwmon sensors to let userspace read
temperatures using standard hwmon interface.

Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
[Yangtao: only keep devm_thermal_add_hwmon_sysfs]
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230620090732.50025-11-frank.li@vivo.com

thermal/drivers/mediatek/lvts_thermal: Remove redundant msg in lvts_ctrl_start()

The upper-layer devm_thermal_add_hwmon_sysfs() function can directly
print error information.

Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230620090732.50025-10-frank.li@vivo.com

thermal/drivers/qcom: Remove redundant msg at probe time

The upper-layer devm_thermal_add_hwmon_sysfs() function can directly
print error information.

Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230620090732.50025-9-frank.li@vivo.com

thermal/drivers/ti-soc: Remove redundant msg in ti_thermal_expose_sensor()

The upper-layer devm_thermal_add_hwmon_sysfs() function can directly
print error information.

Signed-off-by: Yangtao Li <frank.li@vivo.com>
Acked-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230620090732.50025-8-frank.li@vivo.com

thermal/drivers/qoriq: Remove redundant msg in qoriq_tmu_register_tmu_zone()

The upper-layer devm_thermal_add_hwmon_sysfs() function can directly
print error information.

Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230620090732.50025-7-frank.li@vivo.com

thermal/drivers/tegra: Remove redundant msg in tegra_tsensor_register_channel()

The upper-layer devm_thermal_add_hwmon_sysfs() function can directly
print error information.

Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230620090732.50025-6-frank.li@vivo.com

drivers/thermal/k3: Remove redundant msg in k3_bandgap_probe()

The upper-layer devm_thermal_add_hwmon_sysfs() function can directly
print error information.

Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230620090732.50025-5-frank.li@vivo.com

thermal/drivers/imx: Remove redundant msg in imx8mm_tmu_probe() and imx_sc_thermal_probe()

The upper-layer devm_thermal_add_hwmon_sysfs() function can directly
print error information.

Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230620090732.50025-4-frank.li@vivo.com

thermal/drivers/amlogic: Remove redundant msg in amlogic_thermal_probe()

The upper-layer devm_thermal_add_hwmon_sysfs() function can directly
print error information.

Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230620090732.50025-3-frank.li@vivo.com

thermal/drivers/sun8i: Remove redundant msg in sun8i_ths_register()

The upper-layer devm_thermal_add_hwmon_sysfs() function can directly
print error information.

Signed-off-by: Yangtao Li <frank.li@vivo.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230620090732.50025-2-frank.li@vivo.com

thermal/hwmon: Add error information printing for devm_thermal_add_hwmon_sysfs()

Ensure that all error handling branches print error information. In this
way, when this function fails, the upper-layer functions can directly
return an error code without missing debugging information. Otherwise,
the error message will be printed redundantly or missing.

Signed-off-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230620090732.50025-1-frank.li@vivo.com

thermal/drivers/stm32: Convert to platform remove callback returning void

The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.

st_thermal_unregister() always returned zero, so convert it to return void
without any loss and then just drop the return from st_mmap_remove().

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230616165641.1055854-1-u.kleine-koenig@pengutronix.de

net/mlx5: Update the driver with the recent thermal changes

The thermal framework is migrating to the generic trip points. The set
of changes also implies a self-encapsulation of the thermal zone
device structure where the internals are no longer directly accessible
but with accessors.

Use the new API instead, so the next changes can be pushed in the
thermal framework without this driver failing to compile.

No functional changes intended.

Cc: Sandipan Patra <spatra@nvidia.com>
Cc: Gal Pressman <gal@nvidia.com>
Cc: Saeed Mahameed <saeedm@nvidia.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230525140135.3589917-2-daniel.lezcano@linaro.org

thermal/drivers/armada: Add support for AP807 thermal data

Add support for the AP807 die thermal data. This is the same as AP806,
except for the coefficients.

ap807 values taken from TSENSE_ADC_16FFC spec, which says:
T(in Celsius) = T(code)*TSENE_GAIN+TSENE_OFFSET
where in default:
TSENE_OFFSET = 128.9
TSENE_GAIN = 0.394

Signed-off-by: Alex Leibovich <alexl@marvell.com>
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>
Reviewed-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/E1qA7yU-00Ea4u-Je@rmk-PC.armlinux.org.uk

dt-bindings: armada-thermal: Add armada-ap807-thermal compatible

Add marvell,armada-ap807-thermal compatible for the AP807 die.

Signed-off-by: Alex Leibovich <alexl@marvell.com>
Reviewed-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/E1qA7yP-00Ea4o-FS@rmk-PC.armlinux.org.uk

thermal/drivers/qoriq: Support version 2.1

i.MX93 use TMU version 2.1, which supports:
- TRITSR_TP5(When this field is 1, you must add 0.5 K to the temperature
that TEMP reports. For example, if TEMP is 300 K and TP5=1, then the
final temperature is 300.5 K.)
- Has 16 TTRCR register: Temperature Range Control (TTRCR0 - TTRCR15)

This patch is to add this support.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230516083746.63436-4-peng.fan@oss.nxp.com

thermal/drivers/qoriq: Only enable supported sensors

There are MAX 16 sensors, but not all of them supported. Such as
i.MX8MQ, there are only 3 sensors. Enabling all 16 sensors will
touch reserved bits from i.MX8MQ reference mannual, and TMU will stuck,
temperature will not update anymore.

Fixes: 45038e03d633 ("thermal: qoriq: Enable all sensors before registering them")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230516083746.63436-3-peng.fan@oss.nxp.com

thermal/drivers/qoriq: No need to program site adjustment register

No need to program site adjustment register, as programming
these registers do not give accurate value and also these
registers are not mentioned in Reference Manual.

Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230516083746.63436-2-peng.fan@oss.nxp.com

thermal/drivers/mediatek/lvts_thermal: Register thermal zones as hwmon sensors

Register thermal zones as hwmon sensors to let userspace read
temperatures using standard hwmon interface.

Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230613091317.1691247-1-wenst@chromium.org

thermal/drivers/sun8i: Fix some error handling paths in sun8i_ths_probe()

Should an error occur after calling sun8i_ths_resource_init() in the probe
function, some resources need to be released, as already done in the
.remove() function.

Switch to the devm_clk_get_enabled() helper and add a new devm_action to
turn sun8i_ths_resource_init() into a fully managed function.

Move the place where reset_control_deassert() is called so that the
recommended order of reset release/clock enable steps is kept.
A64 manual states that:

3.3.6.4. Gating and reset

Make sure that the reset signal has been released before the release of
module clock gating;

This fixes the issue and removes some LoC at the same time.

Fixes: dccc5c3b6f30 ("thermal/drivers/sun8i: Add thermal driver for H6/H5/H3/A64/A83T/R40")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/a8ae84bd2dc4b55fe428f8e20f31438bf8bb6762.1684089931.git.christophe.jaillet@wanadoo.fr

Revert "thermal/drivers/mediatek: Use devm_of_iomap to avoid resource leak in mtk_thermal_probe"

This reverts commit f05c7b7d9ea9477fcc388476c6f4ade8c66d2d26.

That change was causing a regression in the generic-adc-thermal-probed
bootrr test as reported in the kernelci-results list [1].
A proper rework will take longer, so revert it for now.

[1] https://groups.io/g/kernelci-results/message/42660

Fixes: f05c7b7d9ea9 ("thermal/drivers/mediatek: Use devm_of_iomap to avoid resource leak in mtk_thermal_probe")
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230525121811.3360268-1-ricardo.canuelo@collabora.com

thermal/drivers/qcom/tsens-v0_1: Add MSM8909 data

The MSM8909 SoC has 5 thermal sensors in a TSENS v0.1 block. Like
MDM9607 it uses a non-standard default slope value of 3000 [1] and needs
per-sensor "correction factors" to workaround issues with the factory
calibration [2].

[1]: https://git.codelinaro.org/clo/la/kernel/msm-3.18/-/blob/LA.UM.7.7.c26-09100-8x09.0/arch/arm/boot/dts/qcom/msm8909.dtsi#L476
[2]: https://git.codelinaro.org/clo/la/kernel/msm-3.18/-/commit/6df022c6d0c2c1b4a5a6c2124dba4d57910c0911

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230508-msm8909-tsens-v5-6-5eb632235ba7@kernkonzept.com

dt-bindings: thermal: qcom-tsens: Add MSM8909 compatible

MSM8909 uses the TSENS v0.1 block similar to other SoCs like MDM9607.
Document the "qcom,msm8909-tsens" compatible in the existing schema.

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230508-msm8909-tsens-v5-5-5eb632235ba7@kernkonzept.com

dt-bindings: thermal: qcom-tsens: Drop redundant compatibles

Since the SoC compatibles must be followed by the IP version compatible
(e.g. compatible = "qcom,msm8916-tsens", "qcom,tsens-v0_1";) it is
redundant to list all the SoC compatibles again in the if statement.
It will already match the IP-version compatible.

The list has already become inconsistent since for example
"qcom,msm8939-tsens" is covered by the if statement but is not listed
there explicitly like the other SoCs.

Simplify this by dropping the redundant SoC compatibles. ipq8064 and
msm8960 are still needed because they do not have an IP-version
compatible.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230508-msm8909-tsens-v5-4-5eb632235ba7@kernkonzept.com

thermal/drivers/qcom/tsens-v0_1: Add mdm9607 correction offsets

According to the msm-3.18 vendor kernel from Qualcomm, mdm9607 needs
"correction factors" to adjust for additional offsets observed after the
factory calibration values in the fuses [1, 2].

The fixed offsets should be applied unless there is a special
calibration mode value that indicates that no offsets are needed [3].

Note that the new calibration mode values are called differently in this
patch compared to the vendor kernel:
- TSENS_TWO_POINT_CALIB_N_WA -> ONE_PT_CALIB2_NO_OFFSET
- TSENS_TWO_POINT_CALIB_N_OFFSET_WA -> TWO_PT_CALIB_NO_OFFSET
This is because close inspection of the calibration function [3] reveals
that TSENS_TWO_POINT_CALIB_N_WA is actually a "one point" calibration
because the if statements skip all "point2" related code for it.

[1]: https://git.codelinaro.org/clo/la/kernel/msm-3.18/-/commit/d9d2db1b82bf3f72f5de0803d55e6849eb5b671e
[2]: https://git.codelinaro.org/clo/la/kernel/msm-3.18/-/commit/d75aef53a760e8ff7bac54049d00c8b2ee1b193e
[3]: https://git.codelinaro.org/clo/la/kernel/msm-3.18/-/blob/LE.UM.4.3.2.r1-04200-9x07/drivers/thermal/msm-tsens.c#L2987-3136

Fixes: a2149ab815fc ("thermal/drivers/qcom/tsens-v0_1: Add support for MDM9607")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230508-msm8909-tsens-v5-3-5eb632235ba7@kernkonzept.com

thermal/drivers/qcom/tsens-v0_1: Fix mdm9607 slope values

According to the msm-3.18 vendor kernel from Qualcomm [1], mdm9607 uses
a non-standard slope value of 3000 (instead of 3200) for all sensors.
Fill it properly similar to the 8939 code added recently.

[1]: https://git.codelinaro.org/clo/la/kernel/msm-3.18/-/blob/LE.UM.4.3.2.r1-04200-9x07/arch/arm/boot/dts/qcom/mdm9607.dtsi#L875

Fixes: a2149ab815fc ("thermal/drivers/qcom/tsens-v0_1: Add support for MDM9607")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230508-msm8909-tsens-v5-2-5eb632235ba7@kernkonzept.com

thermal/drivers/qcom/tsens: Drop unused legacy structs

The old single-cell parsing code was removed for MSM8939, MDM9607 and
MSM8976 but for some reason the structs defining the bit positions etc
were kept around (unused). Drop them now.

Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 51d78b8b1beb ("thermal/drivers/tsens: Drop single-cell code for mdm9607")
Fixes: dfadb4599ab0 ("thermal/drivers/tsens: Drop single-cell code for msm8939")
Fixes: 3a908971f7cb ("thermal/drivers/tsens: Drop single-cell code for msm8976/msm8956")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230508-msm8909-tsens-v5-1-5eb632235ba7@kernkonzept.com

dt-bindings: thermal: tsens: Add ipq9574 compatible

Qualcomm IPQ9574 has tsens v2.3.1 block, which is similar to IPQ8074 tsens.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com>
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/ec9799504fe5a141e107bb78955d8d427f00553f.1686125196.git.quic_varada@quicinc.com

dt-bindings: thermal: convert bcm2835-thermal bindings to YAML

Convert the DT binding document for bcm2835-thermal from .txt to YAML.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230604121223.9625-10-stefan.wahren@i2se.com

thermal: Allow selecting the bang-bang governor as default

For many setups the bang-bang governor is exactly what we want. Many
ARM SoC-based devices use fans to cool down the entire SoC and that
works well only with the bang-bang governor because it uses the
hysteresis in order to let the fan run for a while to cool the SoC
down below the trip point before switching it off again.

The step-wise governor will behave strangely in these situations. It
doesn't use the hysteresis, so it can lead to situations where the fan
is turned on for only a very brief period and then is switched back off,
only to get switched back on again very quickly because the SoC hasn't
cooled down very much.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20230609124408.3788680-1-thierry.reding@gmail.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

thermal/drivers/qcom/tsens-v0_1: Add support for MSM8226

The MSM8226 TSENS IP has 6 thermal sensors in a TSENS v0.1 block.
The thermal sensors use non-standard slope values.

Signed-off-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230507201225.89694-4-matti.lehtimaki@gmail.com

dt-bindings: thermal: tsens: Add compatible for MSM8226

Qualcomm MSM8226 has tsens v0.1 block.

Signed-off-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230507201225.89694-3-matti.lehtimaki@gmail.com

drivers/thermal/rcar_gen3_thermal: add reading fuses for Gen4

The registers are differently named and at different offsets, but their
functionality is the same as for Gen3.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230511192220.7523-4-wsa+renesas@sang-engineering.com

drivers/thermal/rcar_gen3_thermal: refactor reading fuses into seprarate function

Gen4 will be very different, so refactor Gen3 access into separate call
first.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230511192220.7523-3-wsa+renesas@sang-engineering.com

drivers/thermal/rcar_gen3_thermal: introduce 'info' structure

More items to describe the TSCs are needed soon, so encapsulate the
current 'ths_tj_1' item into a struct.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230511192220.7523-2-wsa+renesas@sang-engineering.com

dt-bindings: thermal: tsens: Add compatible for SM6375

The Qualcomm SM6375 platform has two instances of the tsens v2.8.0 block,
add a compatible for these instances.

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230516-topic-lost_tsens_bindings-v1-2-99715746ddb1@linaro.org

dt-bindings: thermal: tsens: Add QCM2290

Add the TSENS v2.x controller found on QCM2290.

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230516-topic-lost_tsens_bindings-v1-1-99715746ddb1@linaro.org

thermal/intel/intel_soc_dts_iosf: Fix reporting wrong temperatures

Since commit 955fb8719efb ("thermal/intel/intel_soc_dts_iosf: Use Intel
TCC library") intel_soc_dts_iosf is reporting the wrong temperature.

The driver expects tj_max to be in milli-degrees-celcius but after
the switch to the TCC library this is now in degrees celcius so
instead of e.g. 90000 it is set to 90 causing a temperature 45
degrees below tj_max to be reported as -44910 milli-degrees
instead of as 45000 milli-degrees.

Fix this by adding back the lost factor of 1000.

Fixes: 955fb8719efb ("thermal/intel/intel_soc_dts_iosf: Use Intel TCC library")
Reported-by: Bernhard Krug <b.krug@elektronenpumpe.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Cc: 6.3+ <stable@vger.kernel.org> # 6.3+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

thermal: intel: int340x_thermal: New IOCTLs for Passive v2 table

Export Passive version 2 table similar to the way _TRT and _ART tables
via IOCTLs.

This removes need for binary utility to read ACPI Passive 2 table by
providing open source support. This table already has open source
implementation in the user space thermald, when the table is part of
data vault exported by the int3400 sysfs.

This table is supported in some older platforms before Ice Lake
generation.

Passive 2 tables contain multiple entries. Each entry has following
fields:

* Source: Named Reference (String). This is the source device for
   temperature.
* Target: Named Reference (String). This is the target device to
   control.
* Priority: Priority of this device compared to others.
* SamplingPeriod: Time Period in 1/10 of seconds unit.
* PassiveTemp: Passive Temperature in 1/10 of Kelvin.
* SourceDomain: Domain for the source (00:Processor, others reserved).
* ControlKnob: Type of control knob (00:Power Limit 1, others: reserved)
* Limit: The target state to set on reaching passive temperature.
   This can be a string "max", "min" or a power limit value.
* LimitStepSize: Step size during activation.
* UnLimitStepSize: Step size during deactivation.
* Reserved1: Reserved

Three IOCTLs are added similar to IOCTLs for reading TRT:

ACPI_THERMAL_GET_PSVT_COUNT: Number of passive 2 entries.
ACPI_THERMAL_GET_PSVT_LEN: Total return data size (count x each
  passive 2 entry size).
ACPI_THERMAL_GET_PSVT: Get the data as an array of objects with
  passive 2 entries.

This change is based on original development done by:
Todd Brandt <todd.e.brandt@linux.intel.com>

Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Changelog and subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Linux 6.4-rc6

Merge tag 'x86_urgent_for_v6.4_rc6' of git://git./linux/kernel/git/tip/tip

Pull x86 fix from Borislav Petkov:

- Set up the kernel CS earlier in the boot process in case EFI boots
   the kernel after bypassing the decompressor and the CS descriptor
   used ends up being the EFI one which is not mapped in the identity
   page table, leading to early SEV/SNP guest communication exceptions
   resulting in the guest crashing

* tag 'x86_urgent_for_v6.4_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/head/64: Switch to KERNEL_CS as soon as new GDT is installed

Merge tag '6.4-rc5-smb3-server-fixes' of git://git.samba.org/ksmbd

Pull smb server fixes from Steve French:
"Five smb3 server fixes, all also for stable:

   - Fix four slab out of bounds warnings: improve checks for protocol
     id, and for small packet length, and for create context parsing,
     and for negotiate context parsing

   - Fix for incorrect dereferencing POSIX ACLs"

* tag '6.4-rc5-smb3-server-fixes' of git://git.samba.org/ksmbd:
  ksmbd: validate smb request protocol id
  ksmbd: check the validation of pdu_size in ksmbd_conn_handler_loop
  ksmbd: fix posix_acls and acls dereferencing possible ERR_PTR()
  ksmbd: fix out-of-bound read in parse_lease_state()
  ksmbd: fix out-of-bound read in deassemble_neg_contexts()

Merge tag 'i2c-for-6.4-rc6' of git://git./linux/kernel/git/wsa/linux

Pull i2c fixes from Wolfram Sang:
"Biggest news is that Andi Shyti steps in for maintaining the
  controller drivers. Thank you very much!

  Other than that, one new driver maintainer and the rest is usual
  driver bugfixes. at24 has a Kconfig dependecy fix"

* tag 'i2c-for-6.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  MAINTAINERS: Add entries for Renesas RZ/V2M I2C driver
  eeprom: at24: also select REGMAP
  i2c: sprd: Delete i2c adapter in .remove's error path
  i2c: mv64xxx: Fix reading invalid status value in atomic mode
  i2c: designware: fix idx_write_cnt in read loop
  i2c: mchp-pci1xxxx: Avoid cast to incompatible function type
  i2c: img-scb: Fix spelling mistake "innacurate" -> "inaccurate"
  MAINTAINERS: Add myself as I2C host drivers maintainer

Merge tag 'soundwire-6.4-fixes' of git://git./linux/kernel/git/vkoul/soundwire

Pull soundwire fixes from Vinod Koul:
"Core fix for missing flag clear, error patch handling in qcom driver
  and BIOS quirk for HP Spectre x360:

   - HP Spectre x360 soundwire DMI quirk

   - Error path handling for qcom driver

   - Core fix for missing clear of alloc_slave_rt"

* tag 'soundwire-6.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire:
  soundwire: stream: Add missing clear of alloc_slave_rt
  soundwire: qcom: add proper error paths in qcom_swrm_startup()
  soundwire: dmi-quirks: add new mapping for HP Spectre x360

Merge tag 'arm-fixes-6.4-2' of git://git./linux/kernel/git/soc/soc

Pull ARM SoC fixes from Arnd Bergmann:
"Most of the changes this time are for the Qualcomm Snapdragon
  platforms.

  There are bug fixes for error handling in Qualcomm icc-bwmon,
  rpmh-rsc, ramp_controller and rmtfs driver as well as the AMD tee
  firmware driver and a missing initialization in the Arm ff-a firmware
  driver. The Qualcomm RPMh and EDAC drivers need some rework to work
  correctly on all supported chips.

  The DT fixes include:

   - i.MX8 fixes for gpio, pinmux and clock settings

   - ADS touchscreen gpio polarity settings in several machines

   - Address dtb warnings for caches, panel and input-enable properties
     on Qualcomm platforms

   - Incorrect data on qualcomm platforms fir SA8155P power domains,
     SM8550 LLCC, SC7180-lite SDRAM frequencies and SM8550 soundwire

   - Remoteproc firmware paths are corrected for Sony Xperia 10 IV"

* tag 'arm-fixes-6.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (36 commits)
  firmware: arm_ffa: Set handle field to zero in memory descriptor
  ARM: dts: Fix erroneous ADS touchscreen polarities
  arm64: dts: imx8mn-beacon: Fix SPI CS pinmux
  arm64: dts: imx8-ss-dma: assign default clock rate for lpuarts
  arm64: dts: imx8qm-mek: correct GPIOs for USDHC2 CD and WP signals
  EDAC/qcom: Get rid of hardcoded register offsets
  EDAC/qcom: Remove superfluous return variable assignment in qcom_llcc_core_setup()
  arm64: dts: qcom: sm8550: Use the correct LLCC register scheme
  dt-bindings: cache: qcom,llcc: Fix SM8550 description
  arm64: dts: qcom: sc7180-lite: Fix SDRAM freq for misidentified sc7180-lite boards
  arm64: dts: qcom: sm8550: use uint16 for Soundwire interval
  soc: qcom: rpmhpd: Add SA8155P power domains
  arm64: dts: qcom: Split out SA8155P and use correct RPMh power domains
  dt-bindings: power: qcom,rpmpd: Add SA8155P
  soc: qcom: Rename ice to qcom_ice to avoid module name conflict
  soc: qcom: rmtfs: Fix error code in probe()
  soc: qcom: ramp_controller: Fix an error handling path in qcom_ramp_controller_probe()
  ARM: dts: at91: sama7g5ek: fix debounce delay property for shdwc
  ARM: at91: pm: fix imbalanced reference counter for ethernet devices
  arm64: dts: qcom: sm6375-pdx225: Fix remoteproc firmware paths
  ...

Merge tag 'block-6.4-2023-06-09' of git://git.kernel.dk/linux

Pull block fixes from Jens Axboe:

- Fix an issue with the hardware queue nr_active, causing it to become
   imbalanced (Tian)

- Fix an issue with null_blk not releasing pages if configured as
   memory backed (Nitesh)

- Fix a locking issue in dasd (Jan)

* tag 'block-6.4-2023-06-09' of git://git.kernel.dk/linux:
  s390/dasd: Use correct lock while counting channel queue length
  null_blk: Fix: memory release when memory_backed=1
  blk-mq: fix blk_mq_hw_ctx active request accounting

Merge tag 'for_linus' of git://git./linux/kernel/git/mst/vhost

Pull virtio bug fixes from Michael Tsirkin:
"A bunch of fixes all over the place"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  tools/virtio: use canonical ftrace path
  vhost_vdpa: support PACKED when setting-getting vring_base
  vhost: support PACKED when setting-getting vring_base
  vhost: Fix worker hangs due to missed wake up calls
  vhost: Fix crash during early vhost_transport_send_pkt calls
  vhost_net: revert upend_idx only on retriable error
  vhost_vdpa: tell vqs about the negotiated
  vdpa/mlx5: Fix hang when cvq commands are triggered during device unregister
  tools/virtio: Add .gitignore for ringtest
  tools/virtio: Fix arm64 ringtest compilation error
  vduse: avoid empty string for dev name
  vhost: use kzalloc() instead of kmalloc() followed by memset()

Merge tag 'ceph-for-6.4-rc6' of https://github.com/ceph/ceph-client

Pull ceph fixes from Ilya Dryomov:
"A fix for a potential data corruption in differential backup and
  snapshot-based mirroring scenarios in RBD and a reference counting
  fixup to avoid use-after-free in CephFS, all marked for stable"

* tag 'ceph-for-6.4-rc6' of https://github.com/ceph/ceph-client:
  ceph: fix use-after-free bug for inodes when flushing capsnaps
  rbd: get snapshot context after exclusive lock is ensured to be held
  rbd: move RBD_OBJ_FLAG_COPYUP_ENABLED flag setting

s390/dasd: Use correct lock while counting channel queue length

The lock around counting the channel queue length in the BIODASDINFO
ioctl was incorrectly changed to the dasd_block->queue_lock with commit
583d6535cb9d ("dasd: remove dead code"). This can lead to endless list
iterations and a subsequent crash.

The queue_lock is supposed to be used only for queue lists belonging to
dasd_block. For dasd_device related queue lists the ccwdev lock must be
used.

Fix the mentioned issues by correctly using the ccwdev lock instead of
the queue lock.

Fixes: 583d6535cb9d ("dasd: remove dead code")
Cc: stable@vger.kernel.org # v5.0+
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://lore.kernel.org/r/20230609153750.1258763-2-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Merge tag 'riscv-for-linus-6.4-rc6' of git://git./linux/kernel/git/riscv/linux

Pull RISC-V fixes from Palmer Dabbelt:

- A fix to avoid ISA-disallowed privilege mappings that can result from
   WRITE+EXEC mmap requests from userspace.

- A fix for kfence to handle the huge pages.

- A fix to avoid converting misaligned VAs to huge pages.

- ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE has been selected so kprobe
   can understand user pointers.

* tag 'riscv-for-linus-6.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  riscv: fix kprobe __user string arg print fault issue
  riscv: Check the virtual alignment before choosing a map size
  riscv: Fix kfence now that the linear mapping can be backed by PUD/P4D/PGD
  riscv: mm: Ensure prot of VM_WRITE and VM_EXEC must be readable

Merge tag 's390-6.4-3' of git://git./linux/kernel/git/s390/linux

Pull s390 fixes from Alexander Gordeev:

- Avoid linker error for randomly generated config file that has
   CONFIG_BRANCH_PROFILE_NONE enabled and make it similar to riscv, x86
   and also to commit 4bf3ec384edf ("s390: disable branch profiling for
   vdso").

- Currently, if the device is offline and all the channel paths are
   either configured or varied offline, the associated subchannel gets
   unregistered. Don't unregister the subchannel, instead unregister
   offline device.

* tag 's390-6.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/purgatory: disable branch profiling
  s390/cio: unregister device when the only path is gone

Merge tag 'gpio-fixes-for-v6.4-rc6' of git://git./linux/kernel/git/brgl/linux

Pull gpio fixes from Bartosz Golaszewski:
"Two fixes for the GPIO testing module and one commit making Andy a
  reviewer for the GPIO subsystem:

   - fix a memory corruption bug in gpio-sim

   - fix inconsistencies in user-space configuration of gpio-sim

   - make Andy Shevchenko a reviewer for the GPIO subsystem"

* tag 'gpio-fixes-for-v6.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
  MAINTAINERS: add Andy Shevchenko as reviewer for the GPIO subsystem
  gpio: sim: quietly ignore configured lines outside the bank
  gpio: sim: fix memory corruption when adding named lines and unnamed hogs

tools/virtio: use canonical ftrace path

The canonical location for the tracefs filesystem is at /sys/kernel/tracing.

But, from Documentation/trace/ftrace.rst:

  Before 4.1, all ftrace tracing control files were within the debugfs
  file system, which is typically located at /sys/kernel/debug/tracing.
  For backward compatibility, when mounting the debugfs file system,
  the tracefs file system will be automatically mounted at:

  /sys/kernel/debug/tracing

A few spots in tools/virtio still refer to this older debugfs
path, so let's update them to avoid confusion.

Signed-off-by: Ross Zwisler <zwisler@google.com>
Message-Id: <20230215223350.2658616-6-zwisler@google.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>

vhost_vdpa: support PACKED when setting-getting vring_base

Use the right structs for PACKED or split vqs when setting and
getting the vring base.

Fixes: 4c8cf31885f6 ("vhost: introduce vDPA-based backend")
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Message-Id: <20230424225031.18947-4-shannon.nelson@amd.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>

vhost: support PACKED when setting-getting vring_base

Use the right structs for PACKED or split vqs when setting and
getting the vring base.

Fixes: 4c8cf31885f6 ("vhost: introduce vDPA-based backend")
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Message-Id: <20230424225031.18947-3-shannon.nelson@amd.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>

Merge tag 'pinctrl-v6.4-2' of git://git./linux/kernel/git/linusw/linux-pinctrl

Pull pin control fix from Linus Walleij:
"A single fix for the Meson driver, nothing else has surfaced so far
this cycle"

* tag 'pinctrl-v6.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: meson-axg: add missing GPIOA_18 gpio group

Merge tag 'sound-6.4-rc6' of git://git./linux/kernel/git/tiwai/sound

Pull sound fixes from Takashi Iwai:
"Lots of small fixes, and almost all are device-specific.

  A few of them are the fixes for the old regressions by the fast kctl
  lookups (introduced around 5.19). Others are ASoC simple-card fixes,
  selftest compile warning fixes, ASoC AMD quirks, various ASoC codec
  fixes as well as usual HD-audio quirks"

* tag 'sound-6.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (26 commits)
  ALSA: hda/realtek: Enable 4 amplifiers instead of 2 on a HP platform
  ALSA: hda: Fix kctl->id initialization
  ALSA: gus: Fix kctl->id initialization
  ALSA: cmipci: Fix kctl->id initialization
  ALSA: ymfpci: Fix kctl->id initialization
  ALSA: ice1712,ice1724: fix the kcontrol->id initialization
  ALSA: hda/realtek: Add quirk for Clevo NS50AU
  ALSA: hda/realtek: Add quirks for Asus ROG 2024 laptops using CS35L41
  ALSA: hda/realtek: Add "Intel Reference board" and "NUC 13" SSID in the ALC256
  ALSA: hda/realtek: Add Lenovo P3 Tower platform
  ALSA: hda/realtek: Add a quirk for HP Slim Desktop S01
  selftests: alsa: pcm-test: Fix compiler warnings about the format
  ASoC: fsl_sai: Enable BCI bit if SAI works on synchronous mode with BYP asserted
  ASoC: simple-card-utils: fix PCM constraint error check
  ASoC: cs35l56: Remove NULL check from cs35l56_sdw_dai_set_stream()
  ASoC: max98363: limit the number of channel to 1
  ASoC: max98363: Removed 32bit support
  ASoC: mediatek: mt8195: fix use-after-free in driver remove path
  ASoC: mediatek: mt8188: fix use-after-free in driver remove path
  ASoC: amd: yc: Add Thinkpad Neo14 to quirks list for acp6x
  ...

Merge tag 'ext4_for_linus_stable' of git://git./linux/kernel/git/tytso/ext4

Pull ext4 fix from Ted Ts'o:
"Fix an ext4 regression which breaks remounting r/w file systems that
  have the quota feature enabled"

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: only check dquot_initialize_needed() when debugging
  Revert "ext4: don't clear SB_RDONLY when remounting r/w until quota is re-enabled"

Merge tag 'at24-fixes-for-v6.4-rc6' of git://git./linux/kernel/git/brgl/linux into i2c/for-current

at24 fixes for v6.4-rc6

- fix a Kconfig issue (we need to select REGMAP, not only REGMAP_I2C)

Merge tag 'imx-fixes-6.4-2' of git://git./linux/kernel/git/shawnguo/linux into arm/fixes

i.MX fixes for 6.4, round 2:

- Fix SPI CS pinmux for the final production version of imx8mn-beacon
  board.
- Fix GPIOs for USDHC2 CD and WP signals on imx8qm-mek board.
- Assign default clock rate for i.MX8 LPUARTs to fix UART failure.

* tag 'imx-fixes-6.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  arm64: dts: imx8mn-beacon: Fix SPI CS pinmux
  arm64: dts: imx8-ss-dma: assign default clock rate for lpuarts
  arm64: dts: imx8qm-mek: correct GPIOs for USDHC2 CD and WP signals

Link: https://lore.kernel.org/r/20230607141312.GU4199@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'drm-fixes-2023-06-09' of git://anongit.freedesktop.org/drm/drm

Pull drm fixes from Dave Airlie:
"Bit busier and a bit more scattered than usual. amdgpu is the main
  one, with ivpu and msm having a few fixes, then i915, exynos, ast,
  lima, radeon with some misc bits, but overall nothing standing out.

  fb-helper:
   - Fill in fb-helper vars more correctly

  amdgpu:
   - S0ix fixes
   - GPU reset fixes
   - SMU13 fixes
   - SMU11 fixes
   - Misc Display fixes
   - Revert RV/RV2/PCO clock counter changes
   - Fix Stoney xclk value
   - Fix reserved vram debug info

  radeon:
   - Fix a potential use after free

  i915:
   - CDCLK voltage fix for ADL-P
   - eDP wake sync pulse fix
   - Two error handling fixes to selftests

  exynos:
   - Fix wrong return in Exynos vidi driver
   - Fix use-after-free issue to Exynos g2d driver

  ast:
   - resume and modeset fixes for ast

  ivpu:
   - Assorted ivpu fixes

  lima:
   - lima context destroy fix

  msm:
   - Fix max segment size to address splat on newer a6xx
   - Disable PSR by default w/ modparam to re-enable, since there still
     seems to be a lingering issue
   - Fix HPD issue
   - Fix issue with unitialized GMU mutex"

* tag 'drm-fixes-2023-06-09' of git://anongit.freedesktop.org/drm/drm: (32 commits)
  drm/msm/a6xx: initialize GMU mutex earlier
  drm/msm/dp: enable HDP plugin/unplugged interrupts at hpd_enable/disable
  accel/ivpu: Fix sporadic VPU boot failure
  accel/ivpu: Do not use mutex_lock_interruptible
  accel/ivpu: Do not trigger extra VPU reset if the VPU is idle
  drm/amd/display: Reduce sdp bw after urgent to 90%
  drm/amdgpu: change reserved vram info print
  drm/amdgpu: fix xclk freq on CHIP_STONEY
  drm/radeon: fix race condition UAF in radeon_gem_set_domain_ioctl
  Revert "drm/amdgpu: switch to golden tsc registers for raven/raven2"
  Revert "drm/amdgpu: Differentiate between Raven2 and Raven/Picasso according to revision id"
  Revert "drm/amdgpu: change the reference clock for raven/raven2"
  drm/amd/display: add ODM case when looking for first split pipe
  drm/amd: Make lack of `ACPI_FADT_LOW_POWER_S0` or `CONFIG_AMD_PMC` louder during suspend path
  drm/amd/pm: conditionally disable pcie lane switching for some sienna_cichlid SKUs
  drm/amd/pm: Fix power context allocation in SMU13
  drm/amdgpu: fix Null pointer dereference error in amdgpu_device_recover_vram
  drm/amd: Disallow s0ix without BIOS support again
  drm/i915/selftests: Add some missing error propagation
  drm/exynos: fix race condition UAF in exynos_g2d_exec_ioctl
  ...

Merge tag 'cgroup-for-6.4-rc5-fixes' of git://git./linux/kernel/git/tj/cgroup

Pull cgroup fixes from Tejun Heo:

- Fix css_set reference leaks on fork failures

- Fix CPU hotplug locking in cgroup_transfer_tasks() which is used by
   cgroup1 cpuset

- Doc update

* tag 'cgroup-for-6.4-rc5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup: Documentation: Clarify usage of memory limits
  cgroup: always put cset in cgroup_css_set_put_fork
  cgroup: fix missing cpus_read_{lock,unlock}() in cgroup_transfer_tasks()

Merge tag 'drm-msm-fixes-2023-06-08' of https://gitlab.freedesktop.org/drm/msm into drm-fixes

A few more late fixes for v6.4-rc6

+ Fix max segment size to address splat on newer a6xx
+ Disable PSR by default w/ modparam to re-enable, since there
still seems to be a lingering issue
+ Fix HPD issue
+ Fix issue with unitialized GMU mutex

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGufjVZRNT6YfQ7YUXFC7Cz95wdLF7QHAYkiGfp+3Xc3DQ@mail.gmail.com

drm/msm/a6xx: initialize GMU mutex earlier

Move GMU mutex initialization earlier to make sure that it is always
initialized. a6xx_destroy can be called from ther failure path before
GMU initialization.

This fixes the following backtrace:

------------[ cut here ]------------
DEBUG_LOCKS_WARN_ON(lock->magic != lock)
WARNING: CPU: 0 PID: 58 at kernel/locking/mutex.c:582 __mutex_lock+0x1ec/0x3d0
Modules linked in:
CPU: 0 PID: 58 Comm: kworker/u16:1 Not tainted 6.3.0-rc5-00155-g187c06436519 #565
Hardware name: Qualcomm Technologies, Inc. SM8350 HDK (DT)
Workqueue: events_unbound deferred_probe_work_func
pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : __mutex_lock+0x1ec/0x3d0
lr : __mutex_lock+0x1ec/0x3d0
sp : ffff800008993620
x29: ffff800008993620 x28: 0000000000000002 x27: ffff47b253c52800
x26: 0000000001000606 x25: ffff47b240bb2810 x24: fffffffffffffff4
x23: 0000000000000000 x22: ffffc38bba15ac14 x21: 0000000000000002
x20: ffff800008993690 x19: ffff47b2430cc668 x18: fffffffffffe98f0
x17: 6f74616c75676572 x16: 20796d6d75642067 x15: 0000000000000038
x14: 0000000000000000 x13: ffffc38bbba050b8 x12: 0000000000000666
x11: 0000000000000222 x10: ffffc38bbba603e8 x9 : ffffc38bbba050b8
x8 : 00000000ffffefff x7 : ffffc38bbba5d0b8 x6 : 0000000000000222
x5 : 000000000000bff4 x4 : 40000000fffff222 x3 : 0000000000000000
x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff47b240cb1880
Call trace:
__mutex_lock+0x1ec/0x3d0
mutex_lock_nested+0x2c/0x38
a6xx_destroy+0xa0/0x138
a6xx_gpu_init+0x41c/0x618
adreno_bind+0x188/0x290
component_bind_all+0x118/0x248
msm_drm_bind+0x1c0/0x670
try_to_bring_up_aggregate_device+0x164/0x1d0
__component_add+0xa8/0x16c
component_add+0x14/0x20
dsi_dev_attach+0x20/0x2c
dsi_host_attach+0x9c/0x144
devm_mipi_dsi_attach+0x34/0xac
lt9611uxc_attach_dsi.isra.0+0x84/0xfc
lt9611uxc_probe+0x5b8/0x67c
i2c_device_probe+0x1ac/0x358
really_probe+0x148/0x2ac
__driver_probe_device+0x78/0xe0
driver_probe_device+0x3c/0x160
__device_attach_driver+0xb8/0x138
bus_for_each_drv+0x84/0xe0
__device_attach+0x9c/0x188
device_initial_probe+0x14/0x20
bus_probe_device+0xac/0xb0
deferred_probe_work_func+0x8c/0xc8
process_one_work+0x2bc/0x594
worker_thread+0x228/0x438
kthread+0x108/0x10c
ret_from_fork+0x10/0x20
irq event stamp: 299345
hardirqs last enabled at (299345): [<ffffc38bb9ba61e4>] put_cpu_partial+0x1c8/0x22c
hardirqs last disabled at (299344): [<ffffc38bb9ba61dc>] put_cpu_partial+0x1c0/0x22c
softirqs last enabled at (296752): [<ffffc38bb9890434>] _stext+0x434/0x4e8
softirqs last disabled at (296741): [<ffffc38bb989669c>] ____do_softirq+0x10/0x1c
---[ end trace 0000000000000000 ]---

Fixes: 4cd15a3e8b36 ("drm/msm/a6xx: Make GPU destroy a bit safer")
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/531540/
Signed-off-by: Rob Clark <robdclark@chromium.org>

drm/msm/dp: enable HDP plugin/unplugged interrupts at hpd_enable/disable

The internal_hpd flag is set to true by dp_bridge_hpd_enable() and set to
false by dp_bridge_hpd_disable() to handle GPIO pinmuxed into DP controller
case. HDP related interrupts can not be enabled until internal_hpd is set
to true. At current implementation dp_display_config_hpd() will initialize
DP host controller first followed by enabling HDP related interrupts if
internal_hpd was true at that time. Enable HDP related interrupts depends on
internal_hpd status may leave system with DP driver host is in running state
but without HDP related interrupts being enabled. This will prevent external
display from being detected. Eliminated this dependency by moving HDP related
interrupts enable/disable be done at dp_bridge_hpd_enable/disable() directly
regardless of internal_hpd status.

Changes in V3:
-- dp_catalog_ctrl_hpd_enable() and dp_catalog_ctrl_hpd_disable()
-- rewording ocmmit text

Changes in V4:
-- replace dp_display_config_hpd() with dp_display_host_start()
-- move enable_irq() at dp_display_host_start();

Changes in V5:
-- replace dp_display_host_start() with dp_display_host_init()

Changes in V6:
-- squash remove enable_irq() and disable_irq()

Fixes: cd198caddea7 ("drm/msm/dp: Rely on hpd_enable/disable callbacks")
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Tested-by: Leonard Lausen <leonard@lausen.nl> # on sc7180 lazor
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Tested-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Link: https://lore.kernel.org/r/1684878756-17830-1-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Rob Clark <robdclark@chromium.org>

Merge tag 'drm-misc-fixes-2023-06-08' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes

drm-misc-fixes for v6.4-rc6:
- resume and modeset fixes for ast.
- Fill in fb-helper vars more correctly.
- Assorted ivpu fixes.
- lima context destroy fix.

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ea6b88ec-b653-3781-0b68-cd0275c27923@linux.intel.com

Merge tag 'exynos-drm-fixes-for-v6.4-rc6' of git://git./linux/kernel/git/daeinki/drm-exynos into drm-fixes

Two fixups
- Fix wrong return in Exynos vidi driver.
- Fix use-after-free issue to Exynos g2d driver.

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Inki Dae <inki.dae@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230607043148.43303-1-inki.dae@samsung.com

Merge tag 'drm-intel-fixes-2023-06-08' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes

CDCLK voltage fix for ADL-P and eDP wake sync pulse fix.
Two error handling fixes to selftests (to appease static checkers)

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ZIGUHBz7+LsqN2nm@jlahtine-mobl.ger.corp.intel.com

Merge tag 'amd-drm-fixes-6.4-2023-06-07' of https://gitlab.freedesktop.org/agd5f/linux into drm-fixes

amd-drm-fixes-6.4-2023-06-07:

amdgpu:
- S0ix fixes
- GPU reset fixes
- SMU13 fixes
- SMU11 fixes
- Misc Display fixes
- Revert RV/RV2/PCO clock counter changes
- Fix Stoney xclk value
- Fix reserved vram debug info

radeon:
- Fix a potential use after free

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230607213740.7723-1-alexander.deucher@amd.com

Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux

Pull arm64 fixes from Will Deacon:
"Two tiny arm64 fixes for -rc6.

  One fixes a build breakage when MAX_ORDER can be nonsensical if
  CONFIG_EXPERT=y and the other fixes the address masking for perf's
  page fault software events so that it is consistent amongst them:

   - Fix build breakage due to bogus MAX_ORDER definitions on !4k pages

   - Avoid masking fault address for perf software events"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: mm: pass original fault address to handle_mm_fault() in PER_VMA_LOCK block
  arm64: Remove the ARCH_FORCE_MAX_ORDER config input prompt

vhost: Fix worker hangs due to missed wake up calls

We can race where we have added work to the work_list, but
vhost_task_fn has passed that check but not yet set us into
TASK_INTERRUPTIBLE. wake_up_process will see us in TASK_RUNNING and
just return.

This bug was intoduced in commit f9010dbdce91 ("fork, vhost: Use
CLONE_THREAD to fix freezer/ps regression") when I moved the setting
of TASK_INTERRUPTIBLE to simplfy the code and avoid get_signal from
logging warnings about being in the wrong state. This moves the setting
of TASK_INTERRUPTIBLE back to before we test if we need to stop the
task to avoid a possible race there as well. We then have vhost_worker
set TASK_RUNNING if it finds work similar to before.

Fixes: f9010dbdce91 ("fork, vhost: Use CLONE_THREAD to fix freezer/ps regression")
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Message-Id: <20230607192338.6041-3-michael.christie@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

vhost: Fix crash during early vhost_transport_send_pkt calls

If userspace does VHOST_VSOCK_SET_GUEST_CID before VHOST_SET_OWNER we
can race where:
1. thread0 calls vhost_transport_send_pkt -> vhost_work_queue
2. thread1 does VHOST_SET_OWNER which calls vhost_worker_create.
3. vhost_worker_create will set the dev->worker pointer before setting
the worker->vtsk pointer.
4. thread0's vhost_work_queue will see the dev->worker pointer is
set and try to call vhost_task_wake using not yet set worker->vtsk
pointer.
5. We then crash since vtsk is NULL.

Before commit 6e890c5d5021 ("vhost: use vhost_tasks for worker
threads"), we only had the worker pointer so we could just check it to
see if VHOST_SET_OWNER has been done. After that commit we have the
vhost_worker and vhost_task pointer, so we can now hit the bug above.

This patch embeds the vhost_worker in the vhost_dev and moves the work
list initialization back to vhost_dev_init, so we can just check the
worker.vtsk pointer to check if VHOST_SET_OWNER has been done like
before.

Fixes: 6e890c5d5021 ("vhost: use vhost_tasks for worker threads")
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Message-Id: <20230607192338.6041-2-michael.christie@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reported-by: syzbot+d0d442c22fa8db45ff0e@syzkaller.appspotmail.com
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>

vhost_net: revert upend_idx only on retriable error

Fix possible virtqueue used buffers leak and corresponding stuck
in case of temporary -EIO from sendmsg() which is produced by
tun driver while backend device is not up.

In case of no-retriable error and zcopy do not revert upend_idx
to pass packet data (that is update used_idx in corresponding
vhost_zerocopy_signal_used()) as if packet data has been
transferred successfully.

v2: set vq->heads[ubuf->desc].len equal to VHOST_DMA_DONE_LEN
in case of fake successful transmit.

Signed-off-by: Andrey Smetanin <asmetanin@yandex-team.ru>
Message-Id: <20230424204411.24888-1-asmetanin@yandex-team.ru>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Andrey Smetanin <asmetanin@yandex-team.ru>
Acked-by: Jason Wang <jasowang@redhat.com>

vhost_vdpa: tell vqs about the negotiated

As is done in the net, iscsi, and vsock vhost support, let the vdpa vqs
know about the features that have been negotiated. This allows vhost
to more safely make decisions based on the features, such as when using
PACKED vs split queues.

Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20230424225031.18947-2-shannon.nelson@amd.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

vdpa/mlx5: Fix hang when cvq commands are triggered during device unregister

Currently the vdpa device is unregistered after the workqueue that
processes vq commands is disabled. However, the device unregister
process can still send commands to the cvq (a vlan delete for example)
which leads to a hang because the handing workqueue has been disabled
and the command never finishes:

[ 2263.095764] rcu: INFO: rcu_sched self-detected stall on CPU
[ 2263.096307] rcu:        9-....: (5250 ticks this GP) idle=dac4/1/0x4000000000000000 softirq=111009/111009 fqs=2544
[ 2263.097154] rcu:        (t=5251 jiffies g=393549 q=347 ncpus=10)
[ 2263.097648] CPU: 9 PID: 94300 Comm: kworker/u20:2 Not tainted 6.3.0-rc6_for_upstream_min_debug_2023_04_14_00_02 #1
[ 2263.098535] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
[ 2263.099481] Workqueue: mlx5_events mlx5_vhca_state_work_handler [mlx5_core]
[ 2263.100143] RIP: 0010:virtnet_send_command+0x109/0x170
[ 2263.100621] Code: 1d df f5 ff 85 c0 78 5c 48 8b 7b 08 e8 d0 c5 f5 ff 84 c0 75 11 eb 22 48 8b 7b 08 e8 01 b7 f5 ff 84 c0 75 15 f3 90 48 8b 7b 08 <48> 8d 74 24 04 e8 8d c5 f5 ff 48 85 c0 74 de 48 8b 83 f8 00 00 00
[ 2263.102148] RSP: 0018:ffff888139cf36e8 EFLAGS: 00000246
[ 2263.102624] RAX: 0000000000000000 RBX: ffff888166bea940 RCX: 0000000000000001
[ 2263.103244] RDX: 0000000000000000 RSI: ffff888139cf36ec RDI: ffff888146763800
[ 2263.103864] RBP: ffff888139cf3710 R08: ffff88810d201000 R09: 0000000000000000
[ 2263.104473] R10: 0000000000000002 R11: 0000000000000003 R12: 0000000000000002
[ 2263.105082] R13: 0000000000000002 R14: ffff888114528400 R15: ffff888166bea000
[ 2263.105689] FS:  0000000000000000(0000) GS:ffff88852cc80000(0000) knlGS:0000000000000000
[ 2263.106404] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 2263.106925] CR2: 00007f31f394b000 CR3: 000000010615b006 CR4: 0000000000370ea0
[ 2263.107542] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 2263.108163] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 2263.108769] Call Trace:
[ 2263.109059]  <TASK>
[ 2263.109320]  ? check_preempt_wakeup+0x11f/0x230
[ 2263.109750]  virtnet_vlan_rx_kill_vid+0x5a/0xa0
[ 2263.110180]  vlan_vid_del+0x9c/0x170
[ 2263.110546]  vlan_device_event+0x351/0x760 [8021q]
[ 2263.111004]  raw_notifier_call_chain+0x41/0x60
[ 2263.111426]  dev_close_many+0xcb/0x120
[ 2263.111808]  unregister_netdevice_many_notify+0x130/0x770
[ 2263.112297]  ? wq_worker_running+0xa/0x30
[ 2263.112688]  unregister_netdevice_queue+0x89/0xc0
[ 2263.113128]  unregister_netdev+0x18/0x20
[ 2263.113512]  virtnet_remove+0x4f/0x230
[ 2263.113885]  virtio_dev_remove+0x31/0x70
[ 2263.114273]  device_release_driver_internal+0x18f/0x1f0
[ 2263.114746]  bus_remove_device+0xc6/0x130
[ 2263.115146]  device_del+0x173/0x3c0
[ 2263.115502]  ? kernfs_find_ns+0x35/0xd0
[ 2263.115895]  device_unregister+0x1a/0x60
[ 2263.116279]  unregister_virtio_device+0x11/0x20
[ 2263.116706]  device_release_driver_internal+0x18f/0x1f0
[ 2263.117182]  bus_remove_device+0xc6/0x130
[ 2263.117576]  device_del+0x173/0x3c0
[ 2263.117929]  ? vdpa_dev_remove+0x20/0x20 [vdpa]
[ 2263.118364]  device_unregister+0x1a/0x60
[ 2263.118752]  mlx5_vdpa_dev_del+0x4c/0x80 [mlx5_vdpa]
[ 2263.119232]  vdpa_match_remove+0x21/0x30 [vdpa]
[ 2263.119663]  bus_for_each_dev+0x71/0xc0
[ 2263.120054]  vdpa_mgmtdev_unregister+0x57/0x70 [vdpa]
[ 2263.120520]  mlx5v_remove+0x12/0x20 [mlx5_vdpa]
[ 2263.120953]  auxiliary_bus_remove+0x18/0x30
[ 2263.121356]  device_release_driver_internal+0x18f/0x1f0
[ 2263.121830]  bus_remove_device+0xc6/0x130
[ 2263.122223]  device_del+0x173/0x3c0
[ 2263.122581]  ? devl_param_driverinit_value_get+0x29/0x90
[ 2263.123070]  mlx5_rescan_drivers_locked+0xc4/0x2d0 [mlx5_core]
[ 2263.123633]  mlx5_unregister_device+0x54/0x80 [mlx5_core]
[ 2263.124169]  mlx5_uninit_one+0x54/0x150 [mlx5_core]
[ 2263.124656]  mlx5_sf_dev_remove+0x45/0x90 [mlx5_core]
[ 2263.125153]  auxiliary_bus_remove+0x18/0x30
[ 2263.125560]  device_release_driver_internal+0x18f/0x1f0
[ 2263.126052]  bus_remove_device+0xc6/0x130
[ 2263.126451]  device_del+0x173/0x3c0
[ 2263.126815]  mlx5_sf_dev_remove+0x39/0xf0 [mlx5_core]
[ 2263.127318]  mlx5_sf_dev_state_change_handler+0x178/0x270 [mlx5_core]
[ 2263.127920]  blocking_notifier_call_chain+0x5a/0x80
[ 2263.128379]  mlx5_vhca_state_work_handler+0x151/0x200 [mlx5_core]
[ 2263.128951]  process_one_work+0x1bb/0x3c0
[ 2263.129355]  ? process_one_work+0x3c0/0x3c0
[ 2263.129766]  worker_thread+0x4d/0x3c0
[ 2263.130140]  ? process_one_work+0x3c0/0x3c0
[ 2263.130548]  kthread+0xb9/0xe0
[ 2263.130895]  ? kthread_complete_and_exit+0x20/0x20
[ 2263.131349]  ret_from_fork+0x1f/0x30
[ 2263.131717]  </TASK>

The fix is to disable and destroy the workqueue after the device
unregister. It is expected that vhost will not trigger kicks after
the unregister. But even if it would, the wq is disabled already by
setting the pointer to NULL (done so in the referenced commit).

Fixes: ad6dc1daaf29 ("vdpa/mlx5: Avoid processing works if workqueue was destroyed")
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Message-Id: <20230516095800.3549932-1-dtatulea@nvidia.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Acked-by: Jason Wang <jasowang@redhat.com>

tools/virtio: Add .gitignore for ringtest

Ignore executables for ringtest.

Signed-off-by: Rong Tao <rongtao@cestc.cn>
Message-Id: <tencent_C121802C93CB4095C6D7D95113442E830A07@qq.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

tools/virtio: Fix arm64 ringtest compilation error

Add cpu_relax() for arm64 instead of directly assert(), and add assert.h
header file. Also, add smp_wmb and smp_mb for arm64.

Compilation error as follows, avoid __always_inline undefined.

    $ make
    cc -Wall -pthread -O2 -ggdb -flto -fwhole-program -c -o ring.o ring.c
    In file included from ring.c:10:
    main.h: In function ‘busy_wait’:
    main.h:99:21: warning: implicit declaration of function ‘assert’
    [-Wimplicit-function-declaration]
    99 | #define cpu_relax() assert(0)
        |                     ^~~~~~
    main.h:107:17: note: in expansion of macro ‘cpu_relax’
    107 |                 cpu_relax();
        |                 ^~~~~~~~~
    main.h:12:1: note: ‘assert’ is defined in header ‘<assert.h>’; did you
    forget to ‘#include <assert.h>’?
    11 | #include <stdbool.h>
    +++ |+#include <assert.h>
    12 |
    main.h: At top level:
    main.h:143:23: error: expected ‘;’ before ‘void’
    143 | static __always_inline
        |                       ^
        |                       ;
    144 | void __read_once_size(const volatile void *p, void *res, int
    size)
        | ~~~~
    main.h:158:23: error: expected ‘;’ before ‘void’
    158 | static __always_inline void __write_once_size(volatile void *p,
    void *res, int size)
        |                       ^~~~~
        |                       ;
    make: *** [<builtin>: ring.o] Error 1

Signed-off-by: Rong Tao <rongtao@cestc.cn>
Message-Id: <tencent_F53E159DD7925174445D830DA19FACF44B07@qq.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

vduse: avoid empty string for dev name

Syzkaller hits a kernel WARN when the first character of the dev name
provided is NULL. Solution is to add a NULL check before calling
cdev_device_add() in vduse_create_dev().

kobject: (0000000072042169): attempted to be registered with empty name!
WARNING: CPU: 0 PID: 112695 at lib/kobject.c:236
Call Trace:
kobject_add_varg linux/src/lib/kobject.c:390 [inline]
kobject_add+0xf6/0x150 linux/src/lib/kobject.c:442
device_add+0x28f/0xc20 linux/src/drivers/base/core.c:2167
cdev_device_add+0x83/0xc0 linux/src/fs/char_dev.c:546
vduse_create_dev linux/src/drivers/vdpa/vdpa_user/vduse_dev.c:2254 [inline]
vduse_ioctl+0x7b5/0xf30 linux/src/drivers/vdpa/vdpa_user/vduse_dev.c:2316
vfs_ioctl linux/src/fs/ioctl.c:47 [inline]
file_ioctl linux/src/fs/ioctl.c:510 [inline]
do_vfs_ioctl+0x14b/0xa80 linux/src/fs/ioctl.c:697
ksys_ioctl+0x7c/0xa0 linux/src/fs/ioctl.c:714
__do_sys_ioctl linux/src/fs/ioctl.c:721 [inline]
__se_sys_ioctl linux/src/fs/ioctl.c:719 [inline]
__x64_sys_ioctl+0x42/0x50 linux/src/fs/ioctl.c:719
do_syscall_64+0x94/0x330 linux/src/arch/x86/entry/common.c:291
entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fixes: c8a6153b6c59 ("vduse: Introduce VDUSE - vDPA Device in Userspace")
Cc: "Xie Yongji" <xieyongji@bytedance.com>
Reported-by: Xianjun Zeng <zengxianjun@bytedance.com>
Signed-off-by: Sheng Zhao <sheng.zhao@bytedance.com>
Message-Id: <20230530033626.1266794-1-sheng.zhao@bytedance.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xie Yongji <xieyongji@bytedance.com>
Cc: "Michael S. Tsirkin"<mst@redhat.com>, "Jason Wang"<jasowang@redhat.com>,
Reviewed-by: Xie Yongji <xieyongji@bytedance.com>

MAINTAINERS: Add entries for Renesas RZ/V2M I2C driver

Add the MAINTAINERS entries for the Renesas RZ/V2M I2C driver.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Acked-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

riscv: fix kprobe __user string arg print fault issue

On riscv qemu platform, when add kprobe event on do_sys_open() to show
filename string arg, it just print fault as follow:

echo 'p:myprobe do_sys_open dfd=$arg1 filename=+0($arg2):string flags=$arg3
mode=$arg4' > kprobe_events

bash-166     [000] ...1.   360.195367: myprobe: (do_sys_open+0x0/0x84)
dfd=0xffffffffffffff9c filename=(fault) flags=0x8241 mode=0x1b6

bash-166     [000] ...1.   360.219369: myprobe: (do_sys_open+0x0/0x84)
dfd=0xffffffffffffff9c filename=(fault) flags=0x8241 mode=0x1b6

bash-191     [000] ...1.   360.378827: myprobe: (do_sys_open+0x0/0x84)
dfd=0xffffffffffffff9c filename=(fault) flags=0x98800 mode=0x0

As riscv do not select ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE,
the +0($arg2) addr is processed as a kernel address though it is a
userspace address, cause the above filename=(fault) print. So select
ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE to avoid the issue, after that the
kprobe trace is ok as below:

bash-166     [000] ...1.    96.767641: myprobe: (do_sys_open+0x0/0x84)
dfd=0xffffffffffffff9c filename="/dev/null" flags=0x8241 mode=0x1b6

bash-166     [000] ...1.    96.793751: myprobe: (do_sys_open+0x0/0x84)
dfd=0xffffffffffffff9c filename="/dev/null" flags=0x8241 mode=0x1b6

bash-177     [000] ...1.    96.962354: myprobe: (do_sys_open+0x0/0x84)
dfd=0xffffffffffffff9c filename="/sys/kernel/debug/tracing/events/kprobes/"
flags=0x98800 mode=0x0

Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Acked-by: Björn Töpel <bjorn@rivosinc.com>
Fixes: 0ebeea8ca8a4 ("bpf: Restrict bpf_probe_read{, str}() only to archs where they work")
Link: https://lore.kernel.org/r/20230504072910.3742842-1-ruanjinjie@huawei.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>

Merge tag 'net-6.4-rc6' of git://git./linux/kernel/git/netdev/net

Pull networking fixes from Paolo Abeni:
"Including fixes from can, wifi, netfilter, bluetooth and ebpf.

  Current release - regressions:

   - bpf: sockmap: avoid potential NULL dereference in
     sk_psock_verdict_data_ready()

   - wifi: iwlwifi: fix -Warray-bounds bug in iwl_mvm_wait_d3_notif()

   - phylink: actually fix ksettings_set() ethtool call

   - eth: dwmac-qcom-ethqos: fix a regression on EMAC < 3

  Current release - new code bugs:

   - wifi: mt76: fix possible NULL pointer dereference in
     mt7996_mac_write_txwi()

  Previous releases - regressions:

   - netfilter: fix NULL pointer dereference in nf_confirm_cthelper

   - wifi: rtw88/rtw89: correct PS calculation for SUPPORTS_DYNAMIC_PS

   - openvswitch: fix upcall counter access before allocation

   - bluetooth:
      - fix use-after-free in hci_remove_ltk/hci_remove_irk
      - fix l2cap_disconnect_req deadlock

   - nic: bnxt_en: prevent kernel panic when receiving unexpected
     PHC_UPDATE event

  Previous releases - always broken:

   - core: annotate rfs lockless accesses

   - sched: fq_pie: ensure reasonable TCA_FQ_PIE_QUANTUM values

   - netfilter: add null check for nla_nest_start_noflag() in
     nft_dump_basechain_hook()

   - bpf: fix UAF in task local storage

   - ipv4: ping_group_range: allow GID from 2147483648 to 4294967294

   - ipv6: rpl: fix route of death.

   - tcp: gso: really support BIG TCP

   - mptcp: fixes for user-space PM address advertisement

   - smc: avoid to access invalid RMBs' MRs in SMCRv1 ADD LINK CONT

   - can: avoid possible use-after-free when j1939_can_rx_register fails

   - batman-adv: fix UaF while rescheduling delayed work

   - eth: qede: fix scheduling while atomic

   - eth: ice: make writes to /dev/gnssX synchronous"

* tag 'net-6.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (83 commits)
  bnxt_en: Implement .set_port / .unset_port UDP tunnel callbacks
  bnxt_en: Prevent kernel panic when receiving unexpected PHC_UPDATE event
  bnxt_en: Skip firmware fatal error recovery if chip is not accessible
  bnxt_en: Query default VLAN before VNIC setup on a VF
  bnxt_en: Don't issue AP reset during ethtool's reset operation
  bnxt_en: Fix bnxt_hwrm_update_rss_hash_cfg()
  net: bcmgenet: Fix EEE implementation
  eth: ixgbe: fix the wake condition
  eth: bnxt: fix the wake condition
  lib: cpu_rmap: Fix potential use-after-free in irq_cpu_rmap_release()
  bpf: Add extra path pointer check to d_path helper
  net: sched: fix possible refcount leak in tc_chain_tmplt_add()
  net: sched: act_police: fix sparse errors in tcf_police_dump()
  net: openvswitch: fix upcall counter access before allocation
  net: sched: move rtm_tca_policy declaration to include file
  ice: make writes to /dev/gnssX synchronous
  net: sched: add rcu annotations around qdisc->qdisc_sleeping
  rfs: annotate lockless accesses to RFS sock flow table
  rfs: annotate lockless accesses to sk->sk_rxhash
  virtio_net: use control_buf for coalesce params
  ...

Merge tag 'xfs-6.4-rc5-fixes' of git://git./fs/xfs/xfs-linux

Pull xfs fixes from Dave Chinner:
"These are a set of regression fixes discovered on recent kernels. I
  was hoping to send this to you a week and half ago, but events out of
  my control delayed finalising the changes until early this week.

  Whilst the diffstat looks large for this stage of the merge window, a
  large chunk of it comes from moving the guts of one function from one
  file to another i.e. it's the same code, it is just run in a different
  context where it is safe to hold a specific lock. Otherwise the
  individual changes are relatively small and straigtht forward.

  Summary:

   - Propagate unlinked inode list corruption back up to log recovery
     (regression fix)

   - improve corruption detection for AGFL entries, AGFL indexes and
     XEFI extents (syzkaller fuzzer oops report)

   - Avoid double perag reference release (regression fix)

   - Improve extent merging detection in scrub (regression fix)

   - Fix a new undefined high bit shift (regression fix)

   - Fix for AGF vs inode cluster buffer deadlock (regression fix)"

* tag 'xfs-6.4-rc5-fixes' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: collect errors from inodegc for unlinked inode recovery
  xfs: validate block number being freed before adding to xefi
  xfs: validity check agbnos on the AGFL
  xfs: fix agf/agfl verification on v4 filesystems
  xfs: fix double xfs_perag_rele() in xfs_filestream_pick_ag()
  xfs: fix broken logic when detecting mergeable bmap records
  xfs: Fix undefined behavior of shift into sign bit
  xfs: fix AGF vs inode cluster buffer deadlock
  xfs: defered work could create precommits
  xfs: restore allocation trylock iteration
  xfs: buffer pins need to hold a buffer reference

ext4: only check dquot_initialize_needed() when debugging

ext4_xattr_block_set() relies on its caller to call dquot_initialize()
on the inode.  To assure that this has happened there are WARN_ON
checks.  Unfortunately, this is subject to false positives if there is
an antagonist thread which is flipping the file system at high rates
between r/o and rw.  So only do the check if EXT4_XATTR_DEBUG is
enabled.

Link: https://lore.kernel.org/r/20230608044056.GA1418535@mit.edu
Signed-off-by: Theodore Ts'o <tytso@mit.edu>

Revert "ext4: don't clear SB_RDONLY when remounting r/w until quota is re-enabled"

This reverts commit a44be64bbecb15a452496f60db6eacfee2b59c79.

Link: https://lore.kernel.org/r/653b3359-2005-21b1-039d-c55ca4cffdcc@gmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>

soundwire: stream: Add missing clear of alloc_slave_rt

The current path that skips allocating the slave runtime does not clear
the alloc_slave_rt flag, this is clearly incorrect. Add the missing
clear, so the runtime won't be erroneously cleaned up.

Fixes: f3016b891c8c ("soundwire: stream: sdw_stream_add_ functions can be called multiple times")
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230602101140.2040141-1-ckeepax@opensource.cirrus.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Merge branch 'bnxt_en-bug-fixes'

Michael Chan says:

====================
bnxt_en: Bug fixes

This patchset has the following fixes for bnxt_en:

1. Add missing VNIC ID parameter in the FW message when getting an
updated RSS configuration from the FW.

2. Fix a warning when doing ethtool reset on newer chips.

3. Fix VLAN issue on a VF when a default VLAN is assigned.

4. Fix a problem during DPC (Downstream Port containment) scenario.

5. Fix a NULL pointer dereference when receiving a PTP event from FW.

6. Fix VXLAN/Geneve UDP port delete/add with newer FW.
====================

Link: https://lore.kernel.org/r/20230607075409.228450-1-michael.chan@broadcom.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

bnxt_en: Implement .set_port / .unset_port UDP tunnel callbacks

As per the new udp tunnel framework, drivers which need to know the
details of a port entry (i.e. port type) when it gets deleted should
use the .set_port / .unset_port callbacks.

Implementing the current .udp_tunnel_sync callback would mean that the
deleted tunnel port entry would be all zeros. This used to work on
older firmware because it would not check the input when deleting a
tunnel port. With newer firmware, the delete will now fail and
subsequent tunnel port allocation will fail as a result.

Fixes: 442a35a5a7aa ("bnxt: convert to new udp_tunnel_nic infra")
Reviewed-by: Kalesh Anakkur Purayil <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

bnxt_en: Prevent kernel panic when receiving unexpected PHC_UPDATE event

The firmware can send PHC_RTC_UPDATE async event on a PF that may not
have PTP registered. In such a case, there will be a null pointer
deference for bp->ptp_cfg when we try to handle the event.

Fix it by not registering for this event with the firmware if !bp->ptp_cfg.
Also, check that bp->ptp_cfg is valid before proceeding when we receive
the event.

Fixes: 8bcf6f04d4a5 ("bnxt_en: Handle async event when the PHC is updated in RTC mode")
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

bnxt_en: Skip firmware fatal error recovery if chip is not accessible

Driver starts firmware fatal error recovery by detecting
heartbeat failure or fw reset count register changing. But
these checks are not reliable if the device is not accessible.
This can happen while DPC (Downstream Port containment) is in
progress. Skip firmware fatal recovery if pci_device_is_present()
returns false.

Fixes: acfb50e4e773 ("bnxt_en: Add FW fatal devlink_health_reporter.")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

bnxt_en: Query default VLAN before VNIC setup on a VF

We need to call bnxt_hwrm_func_qcfg() on a VF to query the default
VLAN that may be setup by the PF.  If a default VLAN is enabled,
the VF cannot support VLAN acceleration on the receive side and
the VNIC must be setup to strip out the default VLAN tag.  If a
default VLAN is not enabled, the VF can support VLAN acceleration
on the receive side.  The VNIC should be set up to strip or not
strip the VLAN based on the RX VLAN acceleration setting.

Without this call to determine the default VLAN before calling
bnxt_setup_vnic(), the VNIC may not be set up correctly.  For
example, bnxt_setup_vnic() may set up to strip the VLAN tag based
on stale default VLAN information.  If RX VLAN acceleration is
not enabled, the VLAN tag will be incorrectly stripped and the
RX data path will not work correctly.

Fixes: cf6645f8ebc6 ("bnxt_en: Add function for VF driver to query default VLAN.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

bnxt_en: Don't issue AP reset during ethtool's reset operation

Only older NIC controller's firmware uses the PROC AP reset type.
Firmware on 5731X/5741X and newer chips does not support this reset
type. When bnxt_reset() issues a series of resets, this PROC AP
reset may actually fail on these newer chips because the firmware
is not ready to accept this unsupported command yet. Avoid this
unnecessary error by skipping this reset type on chips that don't
support it.

Fixes: 7a13240e3718 ("bnxt_en: fix ethtool_reset_flags ABI violations")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

bnxt_en: Fix bnxt_hwrm_update_rss_hash_cfg()

We must specify the vnic id of the vnic in the input structure of this
firmware message. Otherwise we will get an error from the firmware.

Fixes: 98a4322b70e8 ("bnxt_en: update RSS config using difference algorithm")
Reviewed-by: Kalesh Anakkur Purayil <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

eeprom: at24: also select REGMAP

Selecting only REGMAP_I2C can leave REGMAP unset, causing build errors,
so also select REGMAP to prevent the build errors.

../drivers/misc/eeprom/at24.c:540:42: warning: 'struct regmap_config' declared inside parameter list will not be visible outside of this definition or declaration
  540 |                                   struct regmap_config *regmap_config)
../drivers/misc/eeprom/at24.c: In function 'at24_make_dummy_client':
../drivers/misc/eeprom/at24.c:552:18: error: implicit declaration of function 'devm_regmap_init_i2c' [-Werror=implicit-function-declaration]
  552 |         regmap = devm_regmap_init_i2c(dummy_client, regmap_config);
../drivers/misc/eeprom/at24.c:552:16: warning: assignment to 'struct regmap *' from 'int' makes pointer from integer without a cast [-Wint-conversion]
  552 |         regmap = devm_regmap_init_i2c(dummy_client, regmap_config);
../drivers/misc/eeprom/at24.c: In function 'at24_probe':
../drivers/misc/eeprom/at24.c:586:16: error: variable 'regmap_config' has initializer but incomplete type
  586 |         struct regmap_config regmap_config = { };
../drivers/misc/eeprom/at24.c:586:30: error: storage size of 'regmap_config' isn't known
  586 |         struct regmap_config regmap_config = { };
../drivers/misc/eeprom/at24.c:586:30: warning: unused variable 'regmap_config' [-Wunused-variable]

Fixes: 5c015258478e ("eeprom: at24: add basic regmap_i2c support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

ceph: fix use-after-free bug for inodes when flushing capsnaps

There is a race between capsnaps flush and removing the inode from
'mdsc->snap_flush_list' list:

   == Thread A ==                     == Thread B ==
ceph_queue_cap_snap()
-> allocate 'capsnapA'
->ihold('&ci->vfs_inode')
->add 'capsnapA' to 'ci->i_cap_snaps'
->add 'ci' to 'mdsc->snap_flush_list'
    ...
   == Thread C ==
ceph_flush_snaps()
->__ceph_flush_snaps()
  ->__send_flush_snap()
                                handle_cap_flushsnap_ack()
                                 ->iput('&ci->vfs_inode')
                                   this also will release 'ci'
                                    ...
      == Thread D ==
                                ceph_handle_snap()
                                 ->flush_snaps()
                                  ->iterate 'mdsc->snap_flush_list'
                                   ->get the stale 'ci'
->remove 'ci' from                ->ihold(&ci->vfs_inode) this
   'mdsc->snap_flush_list'           will WARNING

To fix this we will increase the inode's i_count ref when adding 'ci'
to the 'mdsc->snap_flush_list' list.

[ idryomov: need_put int -> bool ]

Cc: stable@vger.kernel.org
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2209299
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Milind Changire <mchangir@redhat.com>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>

accel/ivpu: Fix sporadic VPU boot failure

Wait for AON bit in HOST_SS_CPR_RST_CLR to return 0 before
starting VPUIP power up sequence, otherwise the VPU device
may sporadically fail to boot.

An error in power up sequence is propagated to the runtime
power management - the device will be in an error state
until the VPU driver is reloaded.

Fixes: 35b137630f08 ("accel/ivpu: Introduce a new DRM driver for Intel VPU")
Cc: stable@vger.kernel.org # 6.3.x
Signed-off-by: Andrzej Kacprowski <andrzej.kacprowski@linux.intel.com>
Reviewed-by: Krystian Pradzynski <krystian.pradzynski@linux.intel.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230607094502.388489-1-stanislaw.gruszka@linux.intel.com

accel/ivpu: Do not use mutex_lock_interruptible

If we get signal when waiting for the mmu->lock we do not invalidate
current MMU configuration that might result in undefined behavior.

Additionally there is little or no benefit on break waiting for
ipc->lock. In current code base, we keep this lock for short periods.

Fixes: 263b2ba5fc93 ("accel/ivpu: Add Intel VPU MMU support")
Reviewed-by: Krystian Pradzynski <krystian.pradzynski@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230525103818.877590-2-stanislaw.gruszka@linux.intel.com

accel/ivpu: Do not trigger extra VPU reset if the VPU is idle

Turning off the PLL and entering D0i3 will reset the VPU so
an explicit IP reset is redundant.
But if the VPU is active, it may interfere with PLL disabling
and to avoid that, we have to issue an additional IP reset
to silence the VPU before turning off the PLL.

Fixes: a8fed6d1e0b9 ("accel/ivpu: Fix power down sequence")
Cc: stable@vger.kernel.org # 6.3.x
Signed-off-by: Andrzej Kacprowski <andrzej.kacprowski@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230525103818.877590-1-stanislaw.gruszka@linux.intel.com