arm64: Ensure VM_WRITE|VM_SHARED ptes are clean by default

commit aa57157be69fb599bd4c38a4b75c5aad74a60ec0 upstream.

Shared and writable mappings (__S.1.) should be clean (!dirty) initially
and made dirty on a subsequent write either through the hardware DBM
(dirty bit management) mechanism or through a write page fault. A clean
pte for the arm64 kernel is one that has PTE_RDONLY set and PTE_DIRTY
clear.

The PAGE_SHARED{,_EXEC} attributes have PTE_WRITE set (PTE_DBM) and
PTE_DIRTY clear. Prior to commit 73e86cb03cf2 ("arm64: Move PTE_RDONLY
bit handling out of set_pte_at()"), it was the responsibility of
set_pte_at() to set the PTE_RDONLY bit and mark the pte clean if the
software PTE_DIRTY bit was not set. However, the above commit removed
the pte_sw_dirty() check and the subsequent setting of PTE_RDONLY in
set_pte_at() while leaving the PAGE_SHARED{,_EXEC} definitions
unchanged. The result is that shared+writable mappings are now dirty by
default

Fix the above by explicitly setting PTE_RDONLY in PAGE_SHARED{,_EXEC}.
In addition, remove the superfluous PTE_DIRTY bit from the kernel PROT_*
attributes.

Fixes: 73e86cb03cf2 ("arm64: Move PTE_RDONLY bit handling out of set_pte_at()")
Cc: <stable@vger.kernel.org> # 4.14.x-
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/idle: fix cpu idle time calculation

commit 3d7efa4edd07be5c5c3ffa95ba63e97e070e1f3f upstream.

The idle time reported in /proc/stat sometimes incorrectly contains
huge values on s390. This is caused by a bug in arch_cpu_idle_time().

The kernel tries to figure out when a different cpu entered idle by
accessing its per-cpu data structure. There is an ordering problem: if
the remote cpu has an idle_enter value which is not zero, and an
idle_exit value which is zero, it is assumed it is idle since
"now". The "now" timestamp however is taken before the idle_enter
value is read.

Which in turn means that "now" can be smaller than idle_enter of the
remote cpu. Unconditionally subtracting idle_enter from "now" can thus
lead to a negative value (aka large unsigned value).

Fix this by moving the get_tod_clock() invocation out of the
loop. While at it also make the code a bit more readable.

A similar bug also exists for show_idle_time(). Fix this is as well.

Cc: <stable@vger.kernel.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/cmm: fix information leak in cmm_timeout_handler()

commit b8e51a6a9db94bc1fb18ae831b3dab106b5a4b5f upstream.

The problem is that we were putting the NUL terminator too far:

buf[sizeof(buf) - 1] = '\0';

If the user input isn't NUL terminated and they haven't initialized the
whole buffer then it leads to an info leak.  The NUL terminator should
be:

buf[len - 1] = '\0';

Signed-off-by: Yihui Zeng <yzeng56@asu.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
[heiko.carstens@de.ibm.com: keep semantics of how *lenp and *ppos are handled]
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nl80211: fix validation of mesh path nexthop

commit 1fab1b89e2e8f01204a9c05a39fd0b6411a48593 upstream.

Mesh path nexthop should be a ethernet address, but current validation
checks against 4 byte integers.

Cc: stable@vger.kernel.org
Fixes: 2ec600d672e74 ("nl80211/cfg80211: support for mesh, sta dumping")
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20191029093003.10355-1-markus.theil@tu-ilmenau.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HID: fix error message in hid_open_report()

commit b3a81c777dcb093020680490ab970d85e2f6f04f upstream.

On HID report descriptor parsing error the code displays bogus
pointer instead of error offset (subtracts start=NULL from end).
Make the message more useful by displaying correct error offset
and include total buffer size for reference.

This was carried over from ancient times - "Fixed" commit just
promoted the message from DEBUG to ERROR.

Cc: stable@vger.kernel.org
Fixes: 8c3d52fc393b ("HID: make parser more verbose about parsing errors by default")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HID: Fix assumption that devices have inputs

commit d9d4b1e46d9543a82c23f6df03f4ad697dab361b upstream.

The syzbot fuzzer found a slab-out-of-bounds write bug in the hid-gaff
driver.  The problem is caused by the driver's assumption that the
device must have an input report.  While this will be true for all
normal HID input devices, a suitably malicious device can violate the
assumption.

The same assumption is present in over a dozen other HID drivers.
This patch fixes them by checking that the list of hid_inputs for the
hid_device is nonempty before allowing it to be used.

Reported-and-tested-by: syzbot+403741a091bf41d4ae79@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HID: i2c-hid: add Trekstor Primebook C11B to descriptor override

commit 09f3dbe474735df13dd8a66d3d1231048d9b373f upstream.

The Primebook C11B uses the SIPODEV SP1064 touchpad. There are 2 versions
of this 2-in-1 and the touchpad in the older version does not supply
descriptors, so it has to be added to the override list.

Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: target: cxgbit: Fix cxgbit_fw4_ack()

commit fc5b220b2dcf8b512d9bd46fd17f82257e49bf89 upstream.

Use the pointer 'p' after having tested that pointer instead of before.

Fixes: 5cadafb236df ("target/cxgbit: Fix endianness annotations")
Cc: Varun Prakash <varun@chelsio.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191023202150.22173-1-bvanassche@acm.org
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: whiteheat: fix line-speed endianness

commit 84968291d7924261c6a0624b9a72f952398e258b upstream.

Add missing endianness conversion when setting the line speed so that
this driver might work also on big-endian machines.

Also use an unsigned format specifier in the corresponding debug
message.

Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191029102354.2733-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: whiteheat: fix potential slab corruption

commit 1251dab9e0a2c4d0d2d48370ba5baa095a5e8774 upstream.

Fix a user-controlled slab buffer overflow due to a missing sanity check
on the bulk-out transfer buffer used for control requests.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191029102354.2733-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: xhci: fix __le32/__le64 accessors in debugfs code

commit d5501d5c29a2e684640507cfee428178d6fd82ca upstream.

It looks like some of the xhci debug code is passing u32 to functions
directly from __le32/__le64 fields.
Fix this by using le{32,64}_to_cpu() on these to fix the following
sparse warnings;

xhci-debugfs.c:205:62: warning: incorrect type in argument 1 (different base types)
xhci-debugfs.c:205:62:    expected unsigned int [usertype] field0
xhci-debugfs.c:205:62:    got restricted __le32
xhci-debugfs.c:206:62: warning: incorrect type in argument 2 (different base types)
xhci-debugfs.c:206:62:    expected unsigned int [usertype] field1
xhci-debugfs.c:206:62:    got restricted __le32
...

[Trim down commit message, sparse warnings were similar -Mathias]
Cc: <stable@vger.kernel.org> # 4.15+
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1572013829-14044-4-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: ldusb: fix control-message timeout

commit 52403cfbc635d28195167618690595013776ebde upstream.

USB control-message timeouts are specified in milliseconds, not jiffies.
Waiting 83 minutes for a transfer to complete is a bit excessive.

Fixes: 2824bd250f0b ("[PATCH] USB: add ldusb driver")
Cc: stable <stable@vger.kernel.org> # 2.6.13
Reported-by: syzbot+a4fbb3bb76cda0ea4e58@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191022153127.22295-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: ldusb: fix ring-buffer locking

commit d98ee2a19c3334e9343df3ce254b496f1fc428eb upstream.

The custom ring-buffer implementation was merged without any locking or
explicit memory barriers, but a spinlock was later added by commit
9d33efd9a791 ("USB: ldusb bugfix").

The lock did not cover the update of the tail index once the entry had
been processed, something which could lead to memory corruption on
weakly ordered architectures or due to compiler optimisations.

Specifically, a completion handler running on another CPU might observe
the incremented tail index and update the entry before ld_usb_read() is
done with it.

Fixes: 2824bd250f0b ("[PATCH] USB: add ldusb driver")
Fixes: 9d33efd9a791 ("USB: ldusb bugfix")
Cc: stable <stable@vger.kernel.org> # 2.6.13
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191022143203.5260-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb-storage: Revert commit 747668dbc061 ("usb-storage: Set virt_boundary_mask to avoid SG overflows")

commit 9a976949613132977098fc49510b46fa8678d864 upstream.

Commit 747668dbc061 ("usb-storage: Set virt_boundary_mask to avoid SG
overflows") attempted to solve a problem involving scatter-gather I/O
and USB/IP by setting the virt_boundary_mask for mass-storage devices.

However, it now turns out that this interacts badly with commit
09324d32d2a0 ("block: force an unlimited segment size on queues with a
virt boundary"), which was added later.  A typical error message is:

ehci-pci 0000:00:13.2: swiotlb buffer is full (sz: 327680 bytes),
total 32768 (slots), used 97 (slots)

There is no longer any reason to keep the virt_boundary_mask setting
for usb-storage.  It was needed in the first place only for handling
devices with a block size smaller than the maxpacket size and where
the host controller was not capable of fully general scatter-gather
operation (that is, able to merge two SG segments into a single USB
packet).  But:

High-speed or slower connections never use a bulk maxpacket
value larger than 512;

The SCSI layer does not handle block devices with a block size
smaller than 512 bytes;

All the host controllers capable of SuperSpeed operation can
handle fully general SG;

Since commit ea44d190764b ("usbip: Implement SG support to
vhci-hcd and stub driver") was merged, the USB/IP driver can
also handle SG.

Therefore all supported device/controller combinations should be okay
with no need for any special virt_boundary_mask.  So in order to fix
the swiotlb problem, this patch reverts commit 747668dbc061.

Reported-and-tested-by: Piergiorgio Sartor <piergiorgio.sartor@nexgo.de>
Link: https://marc.info/?l=linux-usb&m=157134199501202&w=2
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Seth Bollinger <Seth.Bollinger@digi.com>
CC: <stable@vger.kernel.org>
Fixes: 747668dbc061 ("usb-storage: Set virt_boundary_mask to avoid SG overflows")
Acked-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1910211145520.1673-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: gadget: Reject endpoints with 0 maxpacket value

commit 54f83b8c8ea9b22082a496deadf90447a326954e upstream.

Endpoints with a maxpacket length of 0 are probably useless.  They
can't transfer any data, and it's not at all unlikely that a UDC will
crash or hang when trying to handle a non-zero-length usb_request for
such an endpoint.  Indeed, dummy-hcd gets a divide error when trying
to calculate the remainder of a transfer length by the maxpacket
value, as discovered by the syzbot fuzzer.

Currently the gadget core does not check for endpoints having a
maxpacket value of 0.  This patch adds a check to usb_ep_enable(),
preventing such endpoints from being used.

As far as I know, none of the gadget drivers in the kernel tries to
create an endpoint with maxpacket = 0, but until now there has been
nothing to prevent userspace programs under gadgetfs or configfs from
doing it.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+8ab8bf161038a8768553@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1910281052370.1485-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

UAS: Revert commit 3ae62a42090f ("UAS: fix alignment of scatter/gather segments")

commit 1186f86a71130a7635a20843e355bb880c7349b2 upstream.

Commit 3ae62a42090f ("UAS: fix alignment of scatter/gather segments"),
copying a similar commit for usb-storage, attempted to solve a problem
involving scatter-gather I/O and USB/IP by setting the
virt_boundary_mask for mass-storage devices.

However, it now turns out that the analogous change in usb-storage
interacted badly with commit 09324d32d2a0 ("block: force an unlimited
segment size on queues with a virt boundary"), which was added later.
A typical error message is:

ehci-pci 0000:00:13.2: swiotlb buffer is full (sz: 327680 bytes),
total 32768 (slots), used 97 (slots)

There is no longer any reason to keep the virt_boundary_mask setting
in the uas driver.  It was needed in the first place only for
handling devices with a block size smaller than the maxpacket size and
where the host controller was not capable of fully general
scatter-gather operation (that is, able to merge two SG segments into
a single USB packet).  But:

High-speed or slower connections never use a bulk maxpacket
value larger than 512;

The SCSI layer does not handle block devices with a block size
smaller than 512 bytes;

All the host controllers capable of SuperSpeed operation can
handle fully general SG;

Since commit ea44d190764b ("usbip: Implement SG support to
vhci-hcd and stub driver") was merged, the USB/IP driver can
also handle SG.

Therefore all supported device/controller combinations should be okay
with no need for any special virt_boundary_mask.  So in order to head
off potential problems similar to those affecting usb-storage, this
patch reverts commit 3ae62a42090f.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Oliver Neukum <oneukum@suse.com>
CC: <stable@vger.kernel.org>
Acked-by: Christoph Hellwig <hch@lst.de>
Fixes: 3ae62a42090f ("UAS: fix alignment of scatter/gather segments")
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1910231132470.1878-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/realtek - Add support for ALC623

commit f0778871a13889b86a65d4ad34bef8340af9d082 upstream.

Support new codec ALC623.

Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/ed97b6a8bd9445ecb48bc763d9aaba7a@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/realtek - Fix 2 front mics of codec 0x623

commit 8a6c55d0f883e9a7e7c91841434f3b6bbf932bb2 upstream.

These 2 ThinkCentres installed a new realtek codec ID 0x623,
it has 2 front mics with the same location on pin 0x18 and 0x19.

Apply fixup ALC283_FIXUP_HEADSET_MIC to change 1 front mic
location to right, then pulseaudio can handle them.
One "Front Mic" and one "Mic" will be shown, and audio output works
fine.

Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191024114439.31522-1-aaron.ma@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: bebob: Fix prototype of helper function to return negative value

commit f2bbdbcb075f3977a53da3bdcb7cd460bc8ae5f2 upstream.

A helper function of ALSA bebob driver returns negative value in a
function which has a prototype to return unsigned value.

This commit fixes it by changing the prototype.

Fixes: eb7b3a056cd8 ("ALSA: bebob: Add commands and connections/streams management")
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20191026030620.12077-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fuse: truncate pending writes on O_TRUNC

commit e4648309b85a78f8c787457832269a8712a8673e upstream.

Make sure cached writes are not reordered around open(..., O_TRUNC), with
the obvious wrong results.

Fixes: 4d99ff8f12eb ("fuse: Turn writeback cache on")
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fuse: flush dirty data/metadata before non-truncate setattr

commit b24e7598db62386a95a3c8b9c75630c5d56fe077 upstream.

If writeback cache is enabled, then writes might get reordered with
chmod/chown/utimes.  The problem with this is that performing the write in
the fuse daemon might itself change some of these attributes.  In such case
the following sequence of operations will result in file ending up with the
wrong mode, for example:

  int fd = open ("suid", O_WRONLY|O_CREAT|O_EXCL);
  write (fd, "1", 1);
  fchown (fd, 0, 0);
  fchmod (fd, 04755);
  close (fd);

This patch fixes this by flushing pending writes before performing
chown/chmod/utimes.

Reported-by: Giuseppe Scrivano <gscrivan@redhat.com>
Tested-by: Giuseppe Scrivano <gscrivan@redhat.com>
Fixes: 4d99ff8f12eb ("fuse: Turn writeback cache on")
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ath6kl: fix a NULL-ptr-deref bug in ath6kl_usb_alloc_urb_from_pipe()

[ Upstream commit 39d170b3cb62ba98567f5c4f40c27b5864b304e5 ]

The `ar_usb` field of `ath6kl_usb_pipe_usb_pipe` objects
are initialized to point to the containing `ath6kl_usb` object
according to endpoint descriptors read from the device side, as shown
below in `ath6kl_usb_setup_pipe_resources`:

for (i = 0; i < iface_desc->desc.bNumEndpoints; ++i) {
endpoint = &iface_desc->endpoint[i].desc;

// get the address from endpoint descriptor
pipe_num = ath6kl_usb_get_logical_pipe_num(ar_usb,
endpoint->bEndpointAddress,
&urbcount);
......
// select the pipe object
pipe = &ar_usb->pipes[pipe_num];

// initialize the ar_usb field
pipe->ar_usb = ar_usb;
}

The driver assumes that the addresses reported in endpoint
descriptors from device side  to be complete. If a device is
malicious and does not report complete addresses, it may trigger
NULL-ptr-deref `ath6kl_usb_alloc_urb_from_pipe` and
`ath6kl_usb_free_urb_to_pipe`.

This patch fixes the bug by preventing potential NULL-ptr-deref
(CVE-2019-15098).

Signed-off-by: Hui Peng <benquike@gmail.com>
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

thunderbolt: Use 32-bit writes when writing ring producer/consumer

[ Upstream commit 943795219d3cb9f8ce6ce51cad3ffe1f61e95c6b ]

The register access should be using 32-bit reads/writes according to the
datasheet. With the previous generation hardware 16-bit writes have been
working but starting with ICL this is not the case anymore so fix
producer/consumer register update to use correct width register address.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

USB: legousbtower: fix a signedness bug in tower_probe()

[ Upstream commit fd47a417e75e2506eb3672ae569b1c87e3774155 ]

The problem is that sizeof() is unsigned long so negative error codes
are type promoted to high positive values and the condition becomes
false.

Fixes: 1d427be4a39d ("USB: legousbtower: fix slab info leak at probe")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191011141115.GA4521@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nbd: verify socket is supported during setup

[ Upstream commit cf1b2326b734896734c6e167e41766f9cee7686a ]

nbd requires socket families to support the shutdown method so the nbd
recv workqueue can be woken up from its sock_recvmsg call. If the socket
does not support the callout we will leave recv works running or get hangs
later when the device or module is removed.

This adds a check during socket connection/reconnection to make sure the
socket being passed in supports the needed callout.

Reported-by: syzbot+24c12fa8d218ed26011a@syzkaller.appspotmail.com
Fixes: e9e006f5fcf2 ("nbd: fix max number of supported devs")
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iwlwifi: exclude GEO SAR support for 3168

[ Upstream commit 12e36d98d3e5acf5fc57774e0a15906d55f30cb9 ]

We currently support two NICs in FW version 29, namely 7265D and 3168.
Out of these, only 7265D supports GEO SAR, so adjust the function that
checks for it accordingly.

Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes: f5a47fae6aa3 ("iwlwifi: mvm: fix version check for GEO_TX_POWER_LIMIT support")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ALSA: hda/realtek: Reduce the Headphone static noise on XPS 9350/9360

[ Upstream commit 1099f48457d06b816359fb43ac32a4a07e33219b ]

Headphone on XPS 9350/9360 produces a background white noise. The The
noise level somehow correlates with "Headphone Mic Boost", when it sets
to 1 the noise disappears. However, doing this has a side effect, which
also decreases the overall headphone volume so I didn't send the patch
upstream.

The noise was bearable back then, but after commit 717f43d81afc ("ALSA:
hda/realtek - Update headset mode for ALC256") the noise exacerbates to
a point it starts hurting ears.

So let's use the workaround to set "Headphone Mic Boost" to 1 and lock
it so it's not touchable by userspace.

Fixes: 717f43d81afc ("ALSA: hda/realtek - Update headset mode for ALC256")
BugLink: https://bugs.launchpad.net/bugs/1654448
BugLink: https://bugs.launchpad.net/bugs/1845810
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20191003043919.10960-1-kai.heng.feng@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: 8914/1: NOMMU: Fix exc_ret for XIP

[ Upstream commit 4c0742f65b4ee466546fd24b71b56516cacd4613 ]

It was reported that 72cd4064fcca "NOMMU: Toggle only bits in
EXC_RETURN we are really care of" breaks NOMMU+XIP combination.
It happens because saved EXC_RETURN gets overwritten when data
section is relocated.

The fix is to propagate EXC_RETURN via register and let relocation
code to commit that value into memory.

Fixes: 72cd4064fcca ("ARM: 8830/1: NOMMU: Toggle only bits in EXC_RETURN we are really care of")
Reported-by: afzal mohammed <afzal.mohd.ma@gmail.com>
Tested-by: afzal mohammed <afzal.mohd.ma@gmail.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tracing: Initialize iter->seq after zeroing in tracing_read_pipe()

[ Upstream commit d303de1fcf344ff7c15ed64c3f48a991c9958775 ]

A customer reported the following softlockup:

[899688.160002] NMI watchdog: BUG: soft lockup - CPU#0 stuck for 22s! [test.sh:16464]
[899688.160002] CPU: 0 PID: 16464 Comm: test.sh Not tainted 4.12.14-6.23-azure #1 SLE12-SP4
[899688.160002] RIP: 0010:up_write+0x1a/0x30
[899688.160002] Kernel panic - not syncing: softlockup: hung tasks
[899688.160002] RIP: 0010:up_write+0x1a/0x30
[899688.160002] RSP: 0018:ffffa86784d4fde8 EFLAGS: 00000257 ORIG_RAX: ffffffffffffff12
[899688.160002] RAX: ffffffff970fea00 RBX: 0000000000000001 RCX: 0000000000000000
[899688.160002] RDX: ffffffff00000001 RSI: 0000000000000080 RDI: ffffffff970fea00
[899688.160002] RBP: ffffffffffffffff R08: ffffffffffffffff R09: 0000000000000000
[899688.160002] R10: 0000000000000000 R11: 0000000000000000 R12: ffff8b59014720d8
[899688.160002] R13: ffff8b59014720c0 R14: ffff8b5901471090 R15: ffff8b5901470000
[899688.160002]  tracing_read_pipe+0x336/0x3c0
[899688.160002]  __vfs_read+0x26/0x140
[899688.160002]  vfs_read+0x87/0x130
[899688.160002]  SyS_read+0x42/0x90
[899688.160002]  do_syscall_64+0x74/0x160

It caught the process in the middle of trace_access_unlock(). There is
no loop. So, it must be looping in the caller tracing_read_pipe()
via the "waitagain" label.

Crashdump analyze uncovered that iter->seq was completely zeroed
at this point, including iter->seq.seq.size. It means that
print_trace_line() was never able to print anything and
there was no forward progress.

The culprit seems to be in the code:

/* reset all but tr, trace, and overruns */
memset(&iter->seq, 0,
       sizeof(struct trace_iterator) -
       offsetof(struct trace_iterator, seq));

It was added by the commit 53d0aa773053ab182877 ("ftrace:
add logic to record overruns"). It was v2.6.27-rc1.
It was the time when iter->seq looked like:

     struct trace_seq {
unsigned char buffer[PAGE_SIZE];
unsigned int len;
     };

There was no "size" variable and zeroing was perfectly fine.

The solution is to reinitialize the structure after or without
zeroing.

Link: http://lkml.kernel.org/r/20191011142134.11997-1-pmladek@suse.com
Signed-off-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

s390/uaccess: avoid (false positive) compiler warnings

[ Upstream commit 062795fcdcb2d22822fb42644b1d76a8ad8439b3 ]

Depending on inlining decisions by the compiler, __get/put_user_fn
might become out of line. Then the compiler is no longer able to tell
that size can only be 1,2,4 or 8 due to the check in __get/put_user
resulting in false positives like

./arch/s390/include/asm/uaccess.h: In function ‘__put_user_fn’:
./arch/s390/include/asm/uaccess.h:113:9: warning: ‘rc’ may be used uninitialized in this function [-Wmaybe-uninitialized]
  113 |  return rc;
      |         ^~
./arch/s390/include/asm/uaccess.h: In function ‘__get_user_fn’:
./arch/s390/include/asm/uaccess.h:143:9: warning: ‘rc’ may be used uninitialized in this function [-Wmaybe-uninitialized]
  143 |  return rc;
      |         ^~

These functions are supposed to be always inlined. Mark it as such.

Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

NFSv4: Fix leak of clp->cl_acceptor string

[ Upstream commit 1047ec868332034d1fbcb2fae19fe6d4cb869ff2 ]

Our client can issue multiple SETCLIENTID operations to the same
server in some circumstances. Ensure that calls to
nfs4_proc_setclientid() after the first one do not overwrite the
previously allocated cl_acceptor string.

unreferenced object 0xffff888461031800 (size 32):
  comm "mount.nfs", pid 2227, jiffies 4294822467 (age 1407.749s)
  hex dump (first 32 bytes):
    6e 66 73 40 6b 6c 69 6d 74 2e 69 62 2e 31 30 31  nfs@klimt.ib.101
    35 67 72 61 6e 67 65 72 2e 6e 65 74 00 00 00 00  5granger.net....
  backtrace:
    [<00000000ab820188>] __kmalloc+0x128/0x176
    [<00000000eeaf4ec8>] gss_stringify_acceptor+0xbd/0x1a7 [auth_rpcgss]
    [<00000000e85e3382>] nfs4_proc_setclientid+0x34e/0x46c [nfsv4]
    [<000000003d9cf1fa>] nfs40_discover_server_trunking+0x7a/0xed [nfsv4]
    [<00000000b81c3787>] nfs4_discover_server_trunking+0x81/0x244 [nfsv4]
    [<000000000801b55f>] nfs4_init_client+0x1b0/0x238 [nfsv4]
    [<00000000977daf7f>] nfs4_set_client+0xfe/0x14d [nfsv4]
    [<0000000053a68a2a>] nfs4_create_server+0x107/0x1db [nfsv4]
    [<0000000088262019>] nfs4_remote_mount+0x2c/0x59 [nfsv4]
    [<00000000e84a2fd0>] legacy_get_tree+0x2d/0x4c
    [<00000000797e947c>] vfs_get_tree+0x20/0xc7
    [<00000000ecabaaa8>] fc_mount+0xe/0x36
    [<00000000f15fafc2>] vfs_kern_mount+0x74/0x8d
    [<00000000a3ff4e26>] nfs_do_root_mount+0x8a/0xa3 [nfsv4]
    [<00000000d1c2b337>] nfs4_try_mount+0x58/0xad [nfsv4]
    [<000000004c9bddee>] nfs_fs_mount+0x820/0x869 [nfs]

Fixes: f11b2a1cfbf5 ("nfs4: copy acceptor name from context ... ")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nbd: fix possible sysfs duplicate warning

[ Upstream commit 862488105b84ca744b3d8ff131e0fcfe10644be1 ]

1. nbd_put takes the mutex and drops nbd->ref to 0. It then does
idr_remove and drops the mutex.

2. nbd_genl_connect takes the mutex. idr_find/idr_for_each fails
to find an existing device, so it does nbd_dev_add.

3. just before the nbd_put could call nbd_dev_remove or not finished
totally, but if nbd_dev_add try to add_disk, we can hit:

debugfs: Directory 'nbd1' with parent 'block' already present!

This patch will make sure all the disk add/remove stuff are done
by holding the nbd_index_mutex lock.

Reported-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

virt: vbox: fix memory leak in hgcm_call_preprocess_linaddr

[ Upstream commit e0b0cb9388642c104838fac100a4af32745621e2 ]

In hgcm_call_preprocess_linaddr memory is allocated for bounce_buf but
is not released if copy_form_user fails. In order to prevent memory leak
in case of failure, the assignment to bounce_buf_ret is moved before the
error check. This way the allocated bounce_buf will be released by the
caller.

Fixes: 579db9d45cb4 ("virt: Add vboxguest VMMDEV communication code")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20190930204223.3660-1-navid.emamdoost@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

MIPS: fw: sni: Fix out of bounds init of o32 stack

[ Upstream commit efcb529694c3b707dc0471b312944337ba16e4dd ]

Use ARRAY_SIZE to caluculate the top of the o32 stack.

Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

MIPS: include: Mark __xchg as __always_inline

[ Upstream commit 46f1619500d022501a4f0389f9f4c349ab46bb86 ]

Commit ac7c3e4ff401 ("compiler: enable CONFIG_OPTIMIZE_INLINING
forcibly") allows compiler to uninline functions marked as 'inline'.
In cace of __xchg this would cause to reference function
__xchg_called_with_bad_pointer, which is an error case
for catching bugs and will not happen for correct code, if
__xchg is inlined.

Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

iio: imu: adis16400: release allocated memory on failure

[ Upstream commit ab612b1daf415b62c58e130cb3d0f30b255a14d0 ]

In adis_update_scan_mode, if allocation for adis->buffer fails,
previously allocated adis->xfer needs to be released.

Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amdgpu: fix memory leak

[ Upstream commit 083164dbdb17c5ea4ad92c1782b59c9d75567790 ]

cleanup error handling code and make sure temporary info array
with the handles are freed by amdgpu_bo_list_put() on
idr_replace()'s failure.

Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf/x86/amd: Change/fix NMI latency mitigation to use a timestamp

[ Upstream commit df4d29732fdad43a51284f826bec3e6ded177540 ]

It turns out that the NMI latency workaround from commit:

  6d3edaae16c6 ("x86/perf/amd: Resolve NMI latency issues for active PMCs")

ends up being too conservative and results in the perf NMI handler claiming
NMIs too easily on AMD hardware when the NMI watchdog is active.

This has an impact, for example, on the hpwdt (HPE watchdog timer) module.
This module can produce an NMI that is used to reset the system. It
registers an NMI handler for the NMI_UNKNOWN type and relies on the fact
that nothing has claimed an NMI so that its handler will be invoked when
the watchdog device produces an NMI. After the referenced commit, the
hpwdt module is unable to process its generated NMI if the NMI watchdog is
active, because the current NMI latency mitigation results in the NMI
being claimed by the perf NMI handler.

Update the AMD perf NMI latency mitigation workaround to, instead, use a
window of time. Whenever a PMC is handled in the perf NMI handler, set a
timestamp which will act as a perf NMI window. Any NMIs arriving within
that window will be claimed by perf. Anything outside that window will
not be claimed by perf. The value for the NMI window is set to 100 msecs.
This is a conservative value that easily covers any NMI latency in the
hardware. While this still results in a window in which the hpwdt module
will not receive its NMI, the window is now much, much smaller.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jerry Hoemann <jerry.hoemann@hpe.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 6d3edaae16c6 ("x86/perf/amd: Resolve NMI latency issues for active PMCs")
Link: https://lkml.kernel.org/r/Message-ID:
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

sched/vtime: Fix guest/system mis-accounting on task switch

[ Upstream commit 68e7a4d66b0ce04bf18ff2ffded5596ab3618585 ]

vtime_account_system() assumes that the target task to account cputime
to is always the current task. This is most often true indeed except on
task switch where we call:

vtime_common_task_switch(prev)
vtime_account_system(prev)

Here prev is the scheduling-out task where we account the cputime to. It
doesn't match current that is already the scheduling-in task at this
stage of the context switch.

So we end up checking the wrong task flags to determine if we are
accounting guest or system time to the previous task.

As a result the wrong task is used to check if the target is running in
guest mode. We may then spuriously account or leak either system or
guest time on task switch.

Fix this assumption and also turn vtime_guest_enter/exit() to use the
task passed in parameter as well to avoid future similar issues.

Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wanpeng Li <wanpengli@tencent.com>
Fixes: 2a42eb9594a1 ("sched/cputime: Accumulate vtime on top of nsec clocksource")
Link: https://lkml.kernel.org/r/20190925214242.21873-1-frederic@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86/cpu: Add Comet Lake to the Intel CPU models header

[ Upstream commit 8d7c6ac3b2371eb1cbc9925a88f4d10efff374de ]

Comet Lake is the new 10th Gen Intel processor. Add two new CPU model
numbers to the Intel family list.

The CPU model numbers are not published in the SDM yet but they come
from an authoritative internal source.

 [ bp: Touch up commit message. ]

Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Cc: ak@linux.intel.com
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/1570549810-25049-2-git-send-email-kan.liang@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: armv8_deprecated: Checking return value for memory allocation

[ Upstream commit 3e7c93bd04edfb0cae7dad1215544c9350254b8f ]

There are no return value checking when using kzalloc() and kcalloc() for
memory allocation. so add it.

Signed-off-by: Yunfeng Ye <yeyunfeng@huawei.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

fs: ocfs2: fix a possible null-pointer dereference in ocfs2_info_scan_inode_alloc()

[ Upstream commit 2abb7d3b12d007c30193f48bebed781009bebdd2 ]

In ocfs2_info_scan_inode_alloc(), there is an if statement on line 283
to check whether inode_alloc is NULL:

    if (inode_alloc)

When inode_alloc is NULL, it is used on line 287:

    ocfs2_inode_lock(inode_alloc, &bh, 0);
        ocfs2_inode_lock_full_nested(inode, ...)
            struct ocfs2_super *osb = OCFS2_SB(inode->i_sb);

Thus, a possible null-pointer dereference may occur.

To fix this bug, inode_alloc is checked on line 286.

This bug is found by a static analysis tool STCheck written by us.

Link: http://lkml.kernel.org/r/20190726033717.32359-1-baijiaju1990@gmail.com
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

fs: ocfs2: fix a possible null-pointer dereference in ocfs2_write_end_nolock()

[ Upstream commit 583fee3e12df0e6f1f66f063b989d8e7fed0e65a ]

In ocfs2_write_end_nolock(), there are an if statement on lines 1976,
2047 and 2058, to check whether handle is NULL:

    if (handle)

When handle is NULL, it is used on line 2045:

ocfs2_update_inode_fsync_trans(handle, inode, 1);
        oi->i_sync_tid = handle->h_transaction->t_tid;

Thus, a possible null-pointer dereference may occur.

To fix this bug, handle is checked before calling
ocfs2_update_inode_fsync_trans().

This bug is found by a static analysis tool STCheck written by us.

Link: http://lkml.kernel.org/r/20190726033705.32307-1-baijiaju1990@gmail.com
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

fs: ocfs2: fix possible null-pointer dereferences in ocfs2_xa_prepare_entry()

[ Upstream commit 56e94ea132bb5c2c1d0b60a6aeb34dcb7d71a53d ]

In ocfs2_xa_prepare_entry(), there is an if statement on line 2136 to
check whether loc->xl_entry is NULL:

    if (loc->xl_entry)

When loc->xl_entry is NULL, it is used on line 2158:

    ocfs2_xa_add_entry(loc, name_hash);
        loc->xl_entry->xe_name_hash = cpu_to_le32(name_hash);
        loc->xl_entry->xe_name_offset = cpu_to_le16(loc->xl_size);

and line 2164:

    ocfs2_xa_add_namevalue(loc, xi);
        loc->xl_entry->xe_value_size = cpu_to_le64(xi->xi_value_len);
        loc->xl_entry->xe_name_len = xi->xi_name_len;

Thus, possible null-pointer dereferences may occur.

To fix these bugs, if loc-xl_entry is NULL, ocfs2_xa_prepare_entry()
abnormally returns with -EINVAL.

These bugs are found by a static analysis tool STCheck written by us.

[akpm@linux-foundation.org: remove now-unused ocfs2_xa_add_entry()]
Link: http://lkml.kernel.org/r/20190726101447.9153-1-baijiaju1990@gmail.com
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ocfs2: clear zero in unaligned direct IO

[ Upstream commit 7a243c82ea527cd1da47381ad9cd646844f3b693 ]

Unused portion of a part-written fs-block-sized block is not set to zero
in unaligned append direct write.This can lead to serious data
inconsistencies.

Ocfs2 manage disk with cluster size(for example, 1M), part-written in
one cluster will change the cluster state from UN-WRITTEN to WRITTEN,
VFS(function dio_zero_block) doesn't do the cleaning because bh's state
is not set to NEW in function ocfs2_dio_wr_get_block when we write a
WRITTEN cluster.  For example, the cluster size is 1M, file size is 8k
and we direct write from 14k to 15k, then 12k~14k and 15k~16k will
contain dirty data.

We have to deal with two cases:
 1.The starting position of direct write is outside the file.
 2.The starting position of direct write is located in the file.

We need set bh's state to NEW in the first case.  In the second case, we
need mapped twice because bh's state of area out file should be set to
NEW while area in file not.

[akpm@linux-foundation.org: coding style fixes]
Link: http://lkml.kernel.org/r/5292e287-8f1a-fd4a-1a14-661e555e0bed@huawei.com
Signed-off-by: Jia Guo <guojia12@huawei.com>
Reviewed-by: Yiwen Jiang <jiangyiwen@huawei.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Joseph Qi <joseph.qi@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86/xen: Return from panic notifier

[ Upstream commit c6875f3aacf2a5a913205accddabf0bfb75cac76 ]

Currently execution of panic() continues until Xen's panic notifier
(xen_panic_event()) is called at which point we make a hypercall that
never returns.

This means that any notifier that is supposed to be called later as
well as significant part of panic() code (such as pstore writes from
kmsg_dump()) is never executed.

There is no reason for xen_panic_event() to be this last point in
execution since panic()'s emergency_restart() will call into
xen_emergency_restart() from where we can perform our hypercall.

Nevertheless, we will provide xen_legacy_crash boot option that will
preserve original behavior during crash. This option could be used,
for example, if running kernel dumper (which happens after panic
notifiers) is undesirable.

Reported-by: James Dingwall <james@dingwall.me.uk>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

MIPS: include: Mark __cmpxchg as __always_inline

[ Upstream commit 88356d09904bc606182c625575237269aeece22e ]

Commit ac7c3e4ff401 ("compiler: enable CONFIG_OPTIMIZE_INLINING
forcibly") allows compiler to uninline functions marked as 'inline'.
In cace of cmpxchg this would cause to reference function
__cmpxchg_called_with_bad_pointer, which is a error case
for catching bugs and will not happen for correct code, if
__cmpxchg is inlined.

Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
[paul.burton@mips.com: s/__cmpxchd/__cmpxchg in subject]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

efi/x86: Do not clean dummy variable in kexec path

[ Upstream commit 2ecb7402cfc7f22764e7bbc80790e66eadb20560 ]

kexec reboot fails randomly in UEFI based KVM guest.  The firmware
just resets while calling efi_delete_dummy_variable();  Unfortunately
I don't know how to debug the firmware, it is also possible a potential
problem on real hardware as well although nobody reproduced it.

The intention of the efi_delete_dummy_variable is to trigger garbage collection
when entering virtual mode.  But SetVirtualAddressMap can only run once
for each physical reboot, thus kexec_enter_virtual_mode() is not necessarily
a good place to clean a dummy object.

Drop the efi_delete_dummy_variable so that kexec reboot can work.

Signed-off-by: Dave Young <dyoung@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Matthew Garrett <mjg59@google.com>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: Jerry Snitselaar <jsnitsel@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Octavian Purdila <octavian.purdila@intel.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Scott Talbert <swt@techie.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Cc: linux-integrity@vger.kernel.org
Link: https://lkml.kernel.org/r/20191002165904.8819-8-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

efi/cper: Fix endianness of PCIe class code

[ Upstream commit 6fb9367a15d1a126d222d738b2702c7958594a5f ]

The CPER parser assumes that the class code is big endian, but at least
on this edk2-derived Intel Purley platform it's little endian:

    efi: EFI v2.50 by EDK II BIOS ID:PLYDCRB1.86B.0119.R05.1701181843
    DMI: Intel Corporation PURLEY/PURLEY, BIOS PLYDCRB1.86B.0119.R05.1701181843 01/18/2017

    {1}[Hardware Error]:   device_id: 0000:5d:00.0
    {1}[Hardware Error]:   slot: 0
    {1}[Hardware Error]:   secondary_bus: 0x5e
    {1}[Hardware Error]:   vendor_id: 0x8086, device_id: 0x2030
    {1}[Hardware Error]:   class_code: 000406
                                       ^^^^^^ (should be 060400)

Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Dave Young <dyoung@redhat.com>
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: Jerry Snitselaar <jsnitsel@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Matthew Garrett <mjg59@google.com>
Cc: Octavian Purdila <octavian.purdila@intel.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Scott Talbert <swt@techie.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Cc: linux-integrity@vger.kernel.org
Link: https://lkml.kernel.org/r/20191002165904.8819-2-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

serial: mctrl_gpio: Check for NULL pointer

[ Upstream commit 37e3ab00e4734acc15d96b2926aab55c894f4d9c ]

When using mctrl_gpio_to_gpiod, it dereferences gpios into a single
requested GPIO.  This dereferencing can break if gpios is NULL,
so this patch adds a NULL check before dereferencing it.  If
gpios is NULL, this function will also return NULL.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Yegor Yefremov <yegorslists@googlemail.com>
Link: https://lore.kernel.org/r/20191006163314.23191-1-aford173@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

fs: cifs: mute -Wunused-const-variable message

[ Upstream commit dd19c106a36690b47bb1acc68372f2b472b495b8 ]

After 'Initial git repository build' commit,
'mapping_table_ERRHRD' variable has not been used.

So 'mapping_table_ERRHRD' const variable could be removed
to mute below warning message:

   fs/cifs/netmisc.c:120:40: warning: unused variable 'mapping_table_ERRHRD' [-Wunused-const-variable]
   static const struct smb_to_posix_error mapping_table_ERRHRD[] = {
                                           ^
Signed-off-by: Austin Kim <austindh.kim@gmail.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

gpio: max77620: Use correct unit for debounce times

[ Upstream commit fffa6af94894126994a7600c6f6f09b892e89fa9 ]

The gpiod_set_debounce() function takes the debounce time in
microseconds. Adjust the switch/case values in the MAX77620 GPIO to use
the correct unit.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20191002122825.3948322-1-thierry.reding@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tty: n_hdlc: fix build on SPARC

[ Upstream commit 47a7e5e97d4edd7b14974d34f0e5a5560fad2915 ]

Fix tty driver build on SPARC by not using __exitdata.
It appears that SPARC does not support section .exit.data.

Fixes these build errors:

`.exit.data' referenced in section `.exit.text' of drivers/tty/n_hdlc.o: defined in discarded section `.exit.data' of drivers/tty/n_hdlc.o
`.exit.data' referenced in section `.exit.text' of drivers/tty/n_hdlc.o: defined in discarded section `.exit.data' of drivers/tty/n_hdlc.o
`.exit.data' referenced in section `.exit.text' of drivers/tty/n_hdlc.o: defined in discarded section `.exit.data' of drivers/tty/n_hdlc.o
`.exit.data' referenced in section `.exit.text' of drivers/tty/n_hdlc.o: defined in discarded section `.exit.data' of drivers/tty/n_hdlc.o

Reported-by: kbuild test robot <lkp@intel.com>
Fixes: 063246641d4a ("format-security: move static strings to const")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lore.kernel.org/r/675e7bd9-955b-3ff3-1101-a973b58b5b75@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tty: serial: owl: Fix the link time qualifier of 'owl_uart_exit()'

[ Upstream commit 6264dab6efd6069f0387efb078a9960b5642377b ]

'exit' functions should be marked as __exit, not __init.

Fixes: fc60a8b675bd ("tty: serial: owl: Implement console driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20190910041129.6978-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: ftrace: Ensure synchronisation in PLT setup for Neoverse-N1 #1542419

[ Upstream commit dd8a1f13488438c6c220b7cafa500baaf21a6e53 ]

CPUs affected by Neoverse-N1 #1542419 may execute a stale instruction if
it was recently modified. The affected sequence requires freshly written
instructions to be executable before a branch to them is updated.

There are very few places in the kernel that modify executable text,
all but one come with sufficient synchronisation:
 * The module loader's flush_module_icache() calls flush_icache_range(),
   which does a kick_all_cpus_sync()
 * bpf_int_jit_compile() calls flush_icache_range().
 * Kprobes calls aarch64_insn_patch_text(), which does its work in
   stop_machine().
 * static keys and ftrace both patch between nops and branches to
   existing kernel code (not generated code).

The affected sequence is the interaction between ftrace and modules.
The module PLT is cleaned using __flush_icache_range() as the trampoline
shouldn't be executable until we update the branch to it.

Drop the double-underscore so that this path runs kick_all_cpus_sync()
too.

Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nfs: Fix nfsi->nrequests count error on nfs_inode_remove_request

[ Upstream commit 33ea5aaa87cdae0f9af4d6b7ee4f650a1a36fd1d ]

When xfstests testing, there are some WARNING as below:

WARNING: CPU: 0 PID: 6235 at fs/nfs/inode.c:122 nfs_clear_inode+0x9c/0xd8
Modules linked in:
CPU: 0 PID: 6235 Comm: umount.nfs
Hardware name: linux,dummy-virt (DT)
pstate: 60000005 (nZCv daif -PAN -UAO)
pc : nfs_clear_inode+0x9c/0xd8
lr : nfs_evict_inode+0x60/0x78
sp : fffffc000f68fc00
x29: fffffc000f68fc00 x28: fffffe00c53155c0
x27: fffffe00c5315000 x26: fffffc0009a63748
x25: fffffc000f68fd18 x24: fffffc000bfaaf40
x23: fffffc000936d3c0 x22: fffffe00c4ff5e20
x21: fffffc000bfaaf40 x20: fffffe00c4ff5d10
x19: fffffc000c056000 x18: 000000000000003c
x17: 0000000000000000 x16: 0000000000000000
x15: 0000000000000040 x14: 0000000000000228
x13: fffffc000c3a2000 x12: 0000000000000045
x11: 0000000000000000 x10: 0000000000000000
x9 : 0000000000000000 x8 : 0000000000000000
x7 : 0000000000000000 x6 : fffffc00084b027c
x5 : fffffc0009a64000 x4 : fffffe00c0e77400
x3 : fffffc000c0563a8 x2 : fffffffffffffffb
x1 : 000000000000764e x0 : 0000000000000001
Call trace:
 nfs_clear_inode+0x9c/0xd8
 nfs_evict_inode+0x60/0x78
 evict+0x108/0x380
 dispose_list+0x70/0xa0
 evict_inodes+0x194/0x210
 generic_shutdown_super+0xb0/0x220
 nfs_kill_super+0x40/0x88
 deactivate_locked_super+0xb4/0x120
 deactivate_super+0x144/0x160
 cleanup_mnt+0x98/0x148
 __cleanup_mnt+0x38/0x50
 task_work_run+0x114/0x160
 do_notify_resume+0x2f8/0x308
 work_pending+0x8/0x14

The nrequest should be increased/decreased only if PG_INODE_REF flag
was setted.

But in the nfs_inode_remove_request function, it maybe decrease when
no PG_INODE_REF flag, this maybe lead nrequests count error.

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: ZhangXiaoxu <zhangxiaoxu5@huawei.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

HID: hyperv: Use in-place iterator API in the channel callback

[ Upstream commit 6a297c90efa68b2864483193b8bfb0d19478600c ]

Simplify the ring buffer handling with the in-place API.

Also avoid the dynamic allocation and the memory leak in the channel
callback function.

Signed-off-by: Dexuan Cui <decui@microsoft.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/iwcm: Fix a lock inversion issue

[ Upstream commit b66f31efbdad95ec274345721d99d1d835e6de01 ]

This patch fixes the lock inversion complaint:

============================================
WARNING: possible recursive locking detected
5.3.0-rc7-dbg+ #1 Not tainted
--------------------------------------------
kworker/u16:6/171 is trying to acquire lock:
00000000035c6e6c (&id_priv->handler_mutex){+.+.}, at: rdma_destroy_id+0x78/0x4a0 [rdma_cm]

but task is already holding lock:
00000000bc7c307d (&id_priv->handler_mutex){+.+.}, at: iw_conn_req_handler+0x151/0x680 [rdma_cm]

other info that might help us debug this:
 Possible unsafe locking scenario:

       CPU0
       ----
  lock(&id_priv->handler_mutex);
  lock(&id_priv->handler_mutex);

 *** DEADLOCK ***

 May be due to missing lock nesting notation

3 locks held by kworker/u16:6/171:
 #0: 00000000e2eaa773 ((wq_completion)iw_cm_wq){+.+.}, at: process_one_work+0x472/0xac0
 #1: 000000001efd357b ((work_completion)(&work->work)#3){+.+.}, at: process_one_work+0x476/0xac0
 #2: 00000000bc7c307d (&id_priv->handler_mutex){+.+.}, at: iw_conn_req_handler+0x151/0x680 [rdma_cm]

stack backtrace:
CPU: 3 PID: 171 Comm: kworker/u16:6 Not tainted 5.3.0-rc7-dbg+ #1
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
Workqueue: iw_cm_wq cm_work_handler [iw_cm]
Call Trace:
 dump_stack+0x8a/0xd6
 __lock_acquire.cold+0xe1/0x24d
 lock_acquire+0x106/0x240
 __mutex_lock+0x12e/0xcb0
 mutex_lock_nested+0x1f/0x30
 rdma_destroy_id+0x78/0x4a0 [rdma_cm]
 iw_conn_req_handler+0x5c9/0x680 [rdma_cm]
 cm_work_handler+0xe62/0x1100 [iw_cm]
 process_one_work+0x56d/0xac0
 worker_thread+0x7a/0x5d0
 kthread+0x1bc/0x210
 ret_from_fork+0x24/0x30

This is not a bug as there are actually two lock classes here.

Link: https://lore.kernel.org/r/20190930231707.48259-3-bvanassche@acm.org
Fixes: de910bd92137 ("RDMA/cma: Simplify locking needed for serialization of callbacks")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/hfi1: Prevent memory leak in sdma_init

[ Upstream commit 34b3be18a04ecdc610aae4c48e5d1b799d8689f6 ]

In sdma_init if rhashtable_init fails the allocated memory for
tmp_sdma_rht should be released.

Fixes: 5a52a7acf7e2 ("IB/hfi1: NULL pointer dereference when freeing rhashtable")
Link: https://lore.kernel.org/r/20190925144543.10141-1-navid.emamdoost@gmail.com
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

staging: rtl8188eu: fix null dereference when kzalloc fails

[ Upstream commit 955c1532a34305f2f780b47f0c40cc7c65500810 ]

If kzalloc() returns NULL, the error path doesn't stop the flow of
control from entering rtw_hal_read_chip_version() which dereferences the
null pointer. Fix this by adding a 'goto' to the error path to more
gracefully handle the issue and avoid proceeding with initialization
steps that we're no longer prepared to handle.

Also update the debug message to be more consistent with the other debug
messages in this function.

Addresses-Coverity: ("Dereference after null check")

Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com>
Link: https://lore.kernel.org/r/20190927214415.899-1-connor.kuehl@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf annotate: Return appropriate error code for allocation failures

[ Upstream commit 16ed3c1e91159e28b02f11f71ff4ce4cbc6f99e4 ]

We should return errno or the annotation extra range understood by
symbol__strerror_disassemble() instead of -1, fix it, returning ENOMEM
instead.

Reported-by: Russell King - ARM Linux admin <linux@armlinux.org.uk>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>,
Cc: Will Deacon <will@kernel.org>
Link: https://lkml.kernel.org/n/tip-8of1cmj3rz0mppfcshc9bbqq@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf annotate: Propagate the symbol__annotate() error return

[ Upstream commit 211f493b611eef012841f795166c38ec7528738d ]

We were just returning -1 in symbol__annotate() when symbol__annotate()
failed, propagate its error as it is used later to pass to
symbol__strerror_disassemble() to present a error message to the user,
that in some cases were getting:

  "Invalid -1 error code"

Fix it to propagate the error.

Reported-by: Russell King - ARM Linux admin <linux@armlinux.org.uk>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>,
Cc: Will Deacon <will@kernel.org>
Link: https://lkml.kernel.org/n/tip-0tj89rs9g7nbcyd5skadlvuu@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf annotate: Fix the signedness of failure returns

[ Upstream commit 28f4417c3333940b242af03d90214f713bbef232 ]

Callers of symbol__annotate() expect a errno value or some other
extended error value range in symbol__strerror_disassemble() to
convert to a proper error string, fix it when propagating a failure to
find the arch specific annotation routines via arch__find(arch_name).

Reported-by: Russell King - ARM Linux admin <linux@armlinux.org.uk>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>,
Cc: Will Deacon <will@kernel.org>
Link: https://lkml.kernel.org/n/tip-o0k6dw7cas0vvmjjvgsyvu1i@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf annotate: Propagate perf_env__arch() error

[ Upstream commit a66fa0619a0ae3585ef09e9c33ecfb5c7c6cb72b ]

The callers of symbol__annotate2() use symbol__strerror_disassemble() to
convert its failure returns into a human readable string, so
propagate error values from functions it calls, starting with
perf_env__arch() that when fails the right thing to do is to look at
'errno' to see why its possible call to uname() failed.

Reported-by: Russell King - ARM Linux admin <linux@armlinux.org.uk>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>,
Cc: Will Deacon <will@kernel.org>
Link: https://lkml.kernel.org/n/tip-it5d83kyusfhb1q1b0l4pxzs@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf tools: Propagate get_cpuid() error

[ Upstream commit f67001a4a08eb124197ed4376941e1da9cf94b42 ]

For consistency, propagate the exact cause for get_cpuid() to have
failed.

Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lkml.kernel.org/n/tip-9ig269f7ktnhh99g4l15vpu2@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf jevents: Fix period for Intel fixed counters

[ Upstream commit 6bdfd9f118bd59cf0f85d3bf4b72b586adea17c1 ]

The Intel fixed counters use a special table to override the JSON
information.

During this override the period information from the JSON file got
dropped, which results in inst_retired.any and similar running with
frequency mode instead of a period.

Just specify the expected period in the table.

Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Link: http://lore.kernel.org/lkml/20190927233546.11533-2-andi@firstfloor.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf script brstackinsn: Fix recovery from LBR/binary mismatch

[ Upstream commit e98df280bc2a499fd41d7f9e2d6733884de69902 ]

When the LBR data and the instructions in a binary do not match the loop
printing instructions could get confused and print a long stream of
bogus <bad> instructions.

The problem was that if the instruction decoder cannot decode an
instruction it ilen wasn't initialized, so the loop going through the
basic block would continue with the previous value.

Harden the code to avoid such problems:

- Make sure ilen is always freshly initialized and is 0 for bad
  instructions.

- Do not overrun the code buffer while printing instructions

- Print a warning message if the final jump is not on an instruction
  boundary.

Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Link: http://lore.kernel.org/lkml/20190927233546.11533-1-andi@firstfloor.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf map: Fix overlapped map handling

[ Upstream commit ee212d6ea20887c0ef352be8563ca13dbf965906 ]

Whenever an mmap/mmap2 event occurs, the map tree must be updated to add a new
entry. If a new map overlaps a previous map, the overlapped section of the
previous map is effectively unmapped, but the non-overlapping sections are
still valid.

maps__fixup_overlappings() is responsible for creating any new map entries from
the previously overlapped map. It optionally creates a before and an after map.

When creating the after map the existing code failed to adjust the map.pgoff.
This meant the new after map would incorrectly calculate the file offset
for the ip. This results in incorrect symbol name resolution for any ip in the
after region.

Make maps__fixup_overlappings() correctly populate map.pgoff.

Add an assert that new mapping matches old mapping at the beginning of
the after map.

Committer-testing:

Validated correct parsing of libcoreclr.so symbols from .NET Core 3.0 preview9
(which didn't strip symbols).

Preparation:

  ~/dotnet3.0-preview9/dotnet new webapi -o perfSymbol
  cd perfSymbol
  ~/dotnet3.0-preview9/dotnet publish
  perf record ~/dotnet3.0-preview9/dotnet \
      bin/Debug/netcoreapp3.0/publish/perfSymbol.dll
  ^C

Before:

  perf script --show-mmap-events 2>&1 | grep -e MMAP -e unknown |\
     grep libcoreclr.so | head -n 4
        dotnet  1907 373352.698780: PERF_RECORD_MMAP2 1907/1907: \
            [0x7fe615726000(0x768000) @ 0 08:02 5510620 765057155]: \
            r-xp .../3.0.0-preview9-19423-09/libcoreclr.so
        dotnet  1907 373352.701091: PERF_RECORD_MMAP2 1907/1907: \
            [0x7fe615974000(0x1000) @ 0x24e000 08:02 5510620 765057155]: \
            rwxp .../3.0.0-preview9-19423-09/libcoreclr.so
        dotnet  1907 373352.701241: PERF_RECORD_MMAP2 1907/1907: \
            [0x7fe615c42000(0x1000) @ 0x51c000 08:02 5510620 765057155]: \
            rwxp .../3.0.0-preview9-19423-09/libcoreclr.so
        dotnet  1907 373352.705249:     250000 cpu-clock: \
             7fe6159a1f99 [unknown] \
             (.../3.0.0-preview9-19423-09/libcoreclr.so)

After:

  perf script --show-mmap-events 2>&1 | grep -e MMAP -e unknown |\
     grep libcoreclr.so | head -n 4
        dotnet  1907 373352.698780: PERF_RECORD_MMAP2 1907/1907: \
            [0x7fe615726000(0x768000) @ 0 08:02 5510620 765057155]: \
            r-xp .../3.0.0-preview9-19423-09/libcoreclr.so
        dotnet  1907 373352.701091: PERF_RECORD_MMAP2 1907/1907: \
            [0x7fe615974000(0x1000) @ 0x24e000 08:02 5510620 765057155]: \
            rwxp .../3.0.0-preview9-19423-09/libcoreclr.so
        dotnet  1907 373352.701241: PERF_RECORD_MMAP2 1907/1907: \
            [0x7fe615c42000(0x1000) @ 0x51c000 08:02 5510620 765057155]: \
            rwxp .../3.0.0-preview9-19423-09/libcoreclr.so

All the [unknown] symbols were resolved.

Signed-off-by: Steve MacLean <Steve.MacLean@Microsoft.com>
Tested-by: Brian Robbins <brianrob@microsoft.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Eric Saint-Etienne <eric.saint.etienne@oracle.com>
Cc: John Keeping <john@metanate.com>
Cc: John Salem <josalem@microsoft.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Tom McDonald <thomas.mcdonald@microsoft.com>
Link: http://lore.kernel.org/lkml/BN8PR21MB136270949F22A6A02335C238F7800@BN8PR21MB1362.namprd21.prod.outlook.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf tests: Avoid raising SEGV using an obvious NULL dereference

[ Upstream commit e3e2cf3d5b1fe800b032e14c0fdcd9a6fb20cf3b ]

An optimized build such as:

  make -C tools/perf CLANG=1 CC=clang EXTRA_CFLAGS="-O3

will turn the dereference operation into a ud2 instruction, raising a
SIGILL rather than a SIGSEGV. Use raise(..) for correctness and clarity.

Similar issues were addressed in Numfor Mbiziwo-Tiapo's patch:

  https://lkml.org/lkml/2019/7/8/1234

Committer testing:

Before:

  [root@quaco ~]# perf test hooks
  55: perf hooks                                            : Ok
  [root@quaco ~]# perf test -v hooks
  55: perf hooks                                            :
  --- start ---
  test child forked, pid 17092
  SIGSEGV is observed as expected, try to recover.
  Fatal error (SEGFAULT) in perf hook 'test'
  test child finished with 0
  ---- end ----
  perf hooks: Ok
  [root@quaco ~]#

After:

  [root@quaco ~]# perf test hooks
  55: perf hooks                                            : Ok
  [root@quaco ~]# perf test -v hooks
  55: perf hooks                                            :
  --- start ---
  test child forked, pid 17909
  SIGSEGV is observed as expected, try to recover.
  Fatal error (SEGFAULT) in perf hook 'test'
  test child finished with 0
  ---- end ----
  perf hooks: Ok
  [root@quaco ~]#

Fixes: a074865e60ed ("perf tools: Introduce perf hooks")
Signed-off-by: Ian Rogers <irogers@google.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lore.kernel.org/lkml/20190925195924.152834-2-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

libsubcmd: Make _FORTIFY_SOURCE defines dependent on the feature

[ Upstream commit 4b0b2b096da9d296e0e5668cdfba8613bd6f5bc8 ]

Unconditionally defining _FORTIFY_SOURCE can break tools that don't work
with it, such as memory sanitizers:

  https://github.com/google/sanitizers/wiki/AddressSanitizer#faq

Fixes: 4b6ab94eabe4 ("perf subcmd: Create subcmd library")
Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lore.kernel.org/lkml/20190925195924.152834-1-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iio: fix center temperature of bmc150-accel-core

[ Upstream commit 6c59a962e081df6d8fe43325bbfabec57e0d4751 ]

The center temperature of the supported devices stored in the constant
BMC150_ACCEL_TEMP_CENTER_VAL is not 24 degrees but 23 degrees.

It seems that some datasheets were inconsistent on this value leading
to the error.  For most usecases will only make minor difference so
not queued for stable.

Signed-off-by: Pascal Bouwmann <bouwmann@tau-tec.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iio: adc: meson_saradc: Fix memory allocation order

[ Upstream commit de10ac47597e7a3596b27631d0d5ce5f48d2c099 ]

meson_saradc's irq handler uses priv->regmap so make sure that it is
allocated before the irq get enabled.

This also fixes crash when CONFIG_DEBUG_SHIRQ is enabled, as device
managed resources are freed in the inverted order they had been
allocated, priv->regmap was freed before the spurious fake irq that
CONFIG_DEBUG_SHIRQ adds called the handler.

Fixes: 3af109131b7eb8 ("iio: adc: meson-saradc: switch from polling to interrupt mode")
Reported-by: Elie Roudninski <xademax@gmail.com>
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Elie ROUDNINSKI <xademax@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

power: supply: max14656: fix potential use-after-free

[ Upstream commit 252fbeb86ceffa549af9842cefca2412d53a7653 ]

Explicitly cancel/sync the irq_work delayed work, otherwise
there's a chance that it will run after the device is removed,
which would result in a use-after-free.

Note that cancel/sync should happen:
- after irq's have been disabled, as the isr re-schedules the work
- before the power supply is unregistered, because the work func
    uses the power supply handle.

Cc: Alexander Kurz <akurz@blala.de>
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd/display: fix odm combine pipe reset

[ Upstream commit f25f06b67ba237b76092a6fc522b1a94e84bfa85 ]

We fail to reset the second odm combine pipe. This change fixes
odm pointer management.

Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI/PME: Fix possible use-after-free on remove

[ Upstream commit 7cf58b79b3072029af127ae865ffc6f00f34b1f8 ]

In remove(), ensure that the PME work cannot run after kfree() is called.
Otherwise, this could result in a use-after-free.

This issue was detected with the help of Coccinelle.

Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Sinan Kaya <okaya@kernel.org>
Cc: Frederick Lawler <fred@fredlawl.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: dsa: mv88e6xxx: Release lock while requesting IRQ

[ Upstream commit 342a0ee70acbee97fdeb91349420f8744eb291fb ]

There is no need to hold the register lock while requesting the GPIO
interrupt. By not holding it we can also avoid a false positive
lockdep splat.

Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

exec: load_script: Do not exec truncated interpreter path

[ Upstream commit b5372fe5dc84235dbe04998efdede3c4daa866a9 ]

Commit 8099b047ecc4 ("exec: load_script: don't blindly truncate
shebang string") was trying to protect against a confused exec of a
truncated interpreter path. However, it was overeager and also refused
to truncate arguments as well, which broke userspace, and it was
reverted. This attempts the protection again, but allows arguments to
remain truncated. In an effort to improve readability, helper functions
and comments have been added.

Co-developed-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Samuel Dionne-Riel <samuel@dionne-riel.com>
Cc: Richard Weinberger <richard.weinberger@gmail.com>
Cc: Graham Christensen <graham@grahamc.com>
Cc: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ext4: disallow files with EXT4_JOURNAL_DATA_FL from EXT4_IOC_SWAP_BOOT

[ Upstream commit 6e589291f4b1b700ca12baec5930592a0d51e63c ]

A malicious/clueless root user can use EXT4_IOC_SWAP_BOOT to force a
corner casew which can lead to the file system getting corrupted.
There's no usefulness to allowing this, so just prohibit this case.

Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: vimc: Remove unused but set variables

[ Upstream commit 5515e414f42bf2769caae15b634004d456658284 ]

Remove unused but set variables to clean up the code and avoid
warning.

Signed-off-by: Lucas A. M. Magalhães <lucmaga@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ALSA: hda/realtek - Apply ALC294 hp init also for S4 resume

[ Upstream commit f6ef4e0e284251ff795c541db1129c84515ed044 ]

The init sequence for ALC294 headphone stuff is needed not only for
the boot up time but also for the resume from hibernation, where the
device is switched from the boot kernel without sound driver to the
suspended image.  Since we record the PM event in the device
power_state field, we can now recognize the call pattern and apply the
sequence conditionally.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

cifs: add credits from unmatched responses/messages

[ Upstream commit eca004523811f816bcfca3046ab54e1278e0973b ]

We should add any credits granted to us from unmatched server responses.

Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

CIFS: Respect SMB2 hdr preamble size in read responses

[ Upstream commit bb1bccb60c2ebd9a6f895507d1d48d5ed773814e ]

There are a couple places where we still account for 4 bytes
in the beginning of SMB2 packet which is not true in the current
code. Fix this to use a header preamble size where possible.

Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: lpfc: Correct localport timeout duration error

[ Upstream commit 2a0fb340fcc816975b8b0f2fef913d11999c39cf ]

Current code incorrectly specifies a completion wait timeout duration in 5
jiffies, when it should have been 5 seconds.

Fix the adjust for units for the completion timeout call.

[mkp: manual merge]

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mlxsw: spectrum: Set LAG port collector only when active

[ Upstream commit 48ebab31d424fbdb8ede8914923bec671a933246 ]

The LAG port collecting (receive) function was mistakenly set when the
port was registered as a LAG member, while it should be set only when
the port collection state is set to true. Set LAG port to collecting
when it is set to distributing, as described in the IEEE link
aggregation standard coupled control mux machine state diagram.

Signed-off-by: Nir Dotan <nird@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: kpti: Whitelist HiSilicon Taishan v110 CPUs

[ Upstream commit 0ecc471a2cb7d4d386089445a727f47b59dc9b6e ]

HiSilicon Taishan v110 CPUs didn't implement CSV3 field of the
ID_AA64PFR0_EL1 and are not susceptible to Meltdown, so whitelist
the MIDR in kpti_safe_list[] table.

Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangshaokun <zhangshaokun@hisilicon.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: Add MIDR encoding for HiSilicon Taishan CPUs

commit efd00c722ca855745fcc35a7e6675b5a782a3fc8 upstream.

Adding the MIDR encodings for HiSilicon Taishan v110 CPUs,
which is used in Kunpeng ARM64 server SoCs. TSV110 is the
abbreviation of Taishan v110.

Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangshaokun <zhangshaokun@hisilicon.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtc: pcf8523: set xtal load capacitance from DT

[ Upstream commit 189927e719e36ceefbb8037f23d3849e47833aef ]

Add support for specifying the xtal load capacitance in the DT node.
The pcf8523 supports xtal load capacitance of 7pF or 12.5pF.
If the rtc has the wrong configuration the time will
drift several hours/week.

The driver use the default value 12.5pF.

The DT may specify either 7000fF or 12500fF.
(The DT uses femto Farad to avoid decimal numbers).
Other values are warned and the driver uses the default value.

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: handle warm-reset port requests on hub resume

[ Upstream commit 4fdc1790e6a9ef22399c6bc6e63b80f4609f3b7e ]

On plug-in of my USB-C device, its USB_SS_PORT_LS_SS_INACTIVE
link state bit is set. Greping all the kernel for this bit shows
that the port status requests a warm-reset this way.

This just happens, if its the only device on the root hub, the hub
therefore resumes and the HCDs status_urb isn't yet available.
If a warm-reset request is detected, this sets the hubs event_bits,
which will prevent any auto-suspend and allows the hubs workqueue
to warm-reset the port later in port_event.

Signed-off-by: Jan-Marek Glogowski <glogow@fbihome.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ALSA: usb-audio: Cleanup DSD whitelist

[ Upstream commit 202e69e645545e8dcec5e239658125276a7a315a ]

XMOS/Thesycon family of USB Audio Class firmware flags DSD altsetting
separate from the PCM ones. Thus the DSD altsetting can be auto-detected
based on the flag and doesn't need maintaining specific altsetting
whitelist.

In addition, static VID:PID-to-altsetting whitelisting causes problems
when firmware update changes the altsetting, or same VID:PID is reused
for another device that has different kind of firmware.

This patch removes existing explicit whitelist mappings for XMOS VID
(0x20b1) and Thesycon VID (0x152a).

Also corrects placement of Hegel HD12 and NuPrime DAC-10 to keep list
sorted based on VID.

Signed-off-by: Jussi Laako <jussi@sonarnerd.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: dwc3: gadget: clear DWC3_EP_TRANSFER_STARTED on cmd complete

[ Upstream commit acbfa6c26f21a18830ee064b588c92334305b6af ]

We must wait until End Transfer completes in order to clear
DWC3_EP_TRANSFER_STARTED, otherwise we may confuse the driver.

This patch is in preparation to fix a rare race condition that happens
upon Disconnect Interrupt.

Tested-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: dwc3: gadget: early giveback if End Transfer already completed

[ Upstream commit 9f45581f5eec6786c6eded2b3c85345d82a910c9 ]

There is a rare race condition that may happen during a Disconnect
Interrupt if we have a started request that happens to be
dequeued *after* completion of End Transfer command. If that happens,
that request will be left waiting for completion of an End Transfer
command that will never happen.

If End Transfer command has already completed before, we are safe to
giveback the request straight away.

Tested-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

samples: bpf: fix: seg fault with NULL pointer arg

[ Upstream commit d59dd69d5576d699d7d3f5da0b4738c3a36d0133 ]

When NULL pointer accidentally passed to write_kprobe_events,
due to strlen(NULL), segmentation fault happens.
Changed code returns -1 to deal with this situation.

Bug issued with Smatch, static analysis.

Signed-off-by: Daniel T. Lee <danieltimlee@gmail.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

HID: steam: fix deadlock with input devices.

[ Upstream commit 6b538cc21334b83f09b25dec4aa2d2726bf07ed0 ]

When using this driver with the wireless dongle and some usermode
program that monitors every input device (acpid, for example), while
another usermode client opens and closes the low-level device
repeadedly, the system eventually deadlocks.

The reason is that steam_input_register_device() must not be called with
the mutex held, because the input subsystem has its own synchronization
that clashes with this one: it is possible that steam_input_open() is
called before input_register_device() returns, and since
steam_input_open() needs to lock the mutex, it deadlocks.

However we must hold the mutex when calling any function that sends
commands to the controller. If not, random commands end up falling fail.

Reported-by: Simon Gene Gottlieb <simon@gottliebtfreitag.de>
Signed-off-by: Rodrigo Rivas Costa <rodrigorivascosta@gmail.com>
Tested-by: Simon Gene Gottlieb <simon@gottliebtfreitag.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

HID: steam: fix boot loop with bluetooth firmware

[ Upstream commit cf28aee292e102740e49f74385b4b89c00050763 ]

There is a new firmware for the Steam Controller with support for BLE
connections. When using such a device with a wired connection, it
reboots itself every 10 seconds unless an application has opened it.

Doing hid_hw_open() unconditionally on probe fixes the issue, and the
code becomes simpler.

Signed-off-by: Rodrigo Rivas Costa <rodrigorivascosta@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

NFSv4: Ensure that the state manager exits the loop on SIGKILL

[ Upstream commit a1aa09be21fa344d1f5585aab8164bfae55f57e3 ]

Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

HID: Add ASUS T100CHI keyboard dock battery quirks

[ Upstream commit a767ffea05d2737f6542cd78458a84a157fa216d ]

Add ASUS Transbook T100CHI/T90CHI keyboard dock into battery quirk list, in
order to add specific implementation in hid-asus.

Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

staging: mt7621-pinctrl: use pinconf-generic for 'dt_node_to_map' and 'dt_free_map'

[ Upstream commit 0ca1f90861b6d64386261096b42bfc81ce11948a ]

Instead of reimplement afunction to do 'dt_node_to_map' task like
'rt2880_pinctrl_dt_node_to_map' make use of 'pinconf_generic_dt_node_to_map_all'
generic function for this task. Also use its equivalent function for free which
is 'pinconf_generic_dt_free_map'. Remove 'rt2880_pinctrl_dt_node_to_map' function
which is not needed anymore. This decrease a bit driver LOC and make it more
generic. To properly compile this changes 'GENERIC_PINCONF' option is selected
with the driver in its Kconfig file.

This also fix a problem with function 'rt2880_pinctrl_dt_node_to_map' which was
calling internally 'pinctrl_utils_reserve_map' which expects 'num_maps' to be initialized.
It does a memory allocation based on the value, and triggers the following
warning if is not properly set:

if (unlikely(order >= MAX_ORDER)) {
        WARN_ON_ONCE(!(gfp_mask & __GFP_NOWARN));
        return NULL;
}

Generic function 'pinconf_generic_dt_node_to_map_all' initializes properly
'num_maps' to zero fixing the problem.

Fixes: e12a1a6e087b ("staging: mt7621-pinctrl: refactor rt2880_pinctrl_dt_node_to_map function")
Reported-by: NeilBrown <neil@brown.name>
Tested-by: NeilBrown <neil@brown.name>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scripts/setlocalversion: Improve -dirty check with git-status --no-optional-locks

[ Upstream commit ff64dd4857303dd5550faed9fd598ac90f0f2238 ]

git-diff-index does not refresh the index for you, so using it for a
"-dirty" check can give misleading results. Commit 6147b1cf19651
("scripts/setlocalversion: git: Make -dirty check more robust") tried to
fix this by switching to git-status, but it overlooked the fact that
git-status also writes to the .git directory of the source tree, which
is definitely not kosher for an out-of-tree (O=) build. That is getting
reverted.

Fortunately, git-status now supports avoiding writing to the index via
the --no-optional-locks flag, as of git 2.14. It still calculates an
up-to-date index, but it avoids writing it out to the .git directory.

So, let's retry the solution from commit 6147b1cf19651 using this new
flag first, and if it fails, we assume this is an older version of git
and just use the old git-diff-index method.

It's hairy to get the 'grep -vq' (inverted matching) correct by stashing
the output of git-status (you have to be careful about the difference
betwen "empty stdin" and "blank line on stdin"), so just pipe the output
directly to grep and use a regex that's good enough for both the
git-status and git-diff-index version.

Cc: Christian Kujau <lists@nerdbynature.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Suggested-by: Alexander Kapshuk <alexander.kapshuk@gmail.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Genki Sky <sky@genki.is>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

clk: boston: unregister clks on failure in clk_boston_setup()

[ Upstream commit 8b627f616ed63dcaf922369fc14a5daf8ad03038 ]

The registered clks should unregister when something wrong happens
before going out in function clk_boston_setup().

Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ath10k: assign 'n_cipher_suites = 11' for WCN3990 to enable WPA3

[ Upstream commit 7ba31e6e0cdc0cc2e60e1fcbf467f3c95aea948e ]

Hostapd uses CCMP, GCMP & GCMP-256 as 'wpa_pairwise' option to run WPA3.
In WCN3990 firmware cipher suite numbers 9 to 11 are for CCMP,
GCMP & GCMP-256.

To enable CCMP, GCMP & GCMP-256 cipher suites in WCN3990 firmware,
host sets 'n_cipher_suites = 11' while initializing hardware parameters.

Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1

Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>