Masahiro Yamada [Wed, 30 Mar 2016 01:53:15 +0000 (10:53 +0900)]
ARM: uniphier: add pin-mux settings for NAND, eMMC, SD of PH1-sLD3
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Wed, 30 Mar 2016 01:52:49 +0000 (10:52 +0900)]
ARM: uniphier: enable eMMC on PH1-sLD3 reference board
On PH1-sLD3, eMMC and NAND are assigned to different I/O pins.
Both devices can be enabled at the same time.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Tue, 29 Mar 2016 11:18:45 +0000 (20:18 +0900)]
ARM: uniphier: adjust dram_init() and dram_init_banksize() for ARM64
Currently, these functions assume #address-cells and #size-cells are
both one. Fix them to support 64bit DTB.
Also, I am fixing a buffer overrun bug while I am here. The array
size of gd->bd->bd_dram is CONFIG_NR_DRAM_BANKS. The number of
iteration in the loop should be limited by that CONFIG.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Tue, 29 Mar 2016 11:12:22 +0000 (20:12 +0900)]
ARM: uniphier: drop unneeded defines related to legacy serial driver
These defined were used for pre-DM ns16550 serial driver. They are
unneeded because UniPhier SoCs now use DM serial.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Mon, 28 Mar 2016 12:41:15 +0000 (21:41 +0900)]
ARM: dts: uniphier: add NAND pinmux node
This will be used to set up pin-muxing for the NAND controller.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Mon, 28 Mar 2016 12:39:17 +0000 (21:39 +0900)]
ARM: dts: uniphier: add clock-frequency to serial nodes of LD11/LD20
Since no clock driver is implemented for peripherals in U-Boot yet,
this property is needed for the serial driver to set up the divisor
register.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Thu, 24 Mar 2016 13:32:47 +0000 (22:32 +0900)]
pinctrl: uniphier: support UniPhier PH1-LD11 pinctrl driver
The pinmux of PH1-LD11 is almost a subset of that of PH1-LD20
(as far as used in boot-loader), so this commit makes the driver
shared between the two SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Thu, 24 Mar 2016 13:32:46 +0000 (22:32 +0900)]
pinctrl: uniphier: support UniPhier PH1-LD20 pinctrl driver
Add pin configuration and pinmux support for UniPhier PH1-LD20 SoC.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Thu, 24 Mar 2016 13:32:45 +0000 (22:32 +0900)]
pinctrl: uniphier: support per-pin input enable for new SoCs
Upcoming new pinctrl drivers for PH1-LD11 and PH-LD20 support input
signal gating for each pin. (While, existing ones only support it
per pin-group.) This commit prepares the core part for that.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Thu, 24 Mar 2016 13:32:44 +0000 (22:32 +0900)]
pinctrl: uniphier: introduce capability flag
The core part of the UniPhier pinctrl driver needs to support a new
capability for upcoming UniPhier ARMv8 SoCs. This sometimes happens
because pinctrl drivers include really SoC-specific stuff.
This commit intends to tidy up SoC-specific parameters of the existing
drivers before adding new ones. Having flags would be better than
adding new members every time a new SoC-specific capability comes up.
At this time, there is one flag, UNIPHIER_PINCTRL_CAPS_DBGMUX_SEPARATE.
This capability (I'd say rather quirk) was added for PH1-Pro4 and
PH1-Pro5 as requirement from our customer. For those SoCs, one pin-mux
setting is controlled by the combination of two separate registers; the
LSB bits at register offset (8 * N) and the MSB bits at (8 * N + 4).
Because it is impossible to update two separate registers atomically,
the LOAD_PINCTRL register should be set in order to make the pin-mux
settings really effective.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Thu, 24 Mar 2016 13:32:43 +0000 (22:32 +0900)]
pinctrl: uniphier: use devm_get_addr() to get base address
Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties. (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Thu, 24 Mar 2016 13:32:42 +0000 (22:32 +0900)]
mmc: uniphier: use devm_get_addr() to get base address
Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties. (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Thu, 24 Mar 2016 13:32:41 +0000 (22:32 +0900)]
gpio: uniphier: use devm_get_addr() to get base address
Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties. (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Thu, 24 Mar 2016 13:32:40 +0000 (22:32 +0900)]
i2c: uniphier: use devm_get_addr() to get base address
Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties. (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Thu, 24 Mar 2016 13:32:39 +0000 (22:32 +0900)]
clk: uniphier: use devm_get_addr() to get base address
Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties. (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Thu, 24 Mar 2016 13:32:38 +0000 (22:32 +0900)]
serial: uniphier: use devm_get_addr() to get base address
Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties. (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Thu, 24 Mar 2016 13:23:36 +0000 (22:23 +0900)]
ARM: uniphier: add sramupdate command
This command would be useful to update U-Boot images in SRAM.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Thu, 24 Mar 2016 13:22:23 +0000 (22:22 +0900)]
ARM: uniphier: make u-boot-with-spl.bin really available
Commit
d085ecd61b99 ("ARM: uniphier: switch to raw U-Boot image")
claimed that u-boot-with-spl.bin would be useful in its commit log,
but it was not available because the commit missed to define
CONFIG_SPL_MAX_SIZE. Without it, CONFIG_SPL_PAD_TO is not defined
either (see include/config_fallbacks.h). So, the SPL image is not
padded correctly.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Graham Moore [Thu, 24 Mar 2016 13:14:35 +0000 (22:14 +0900)]
mtd: nand: denali: max_banks calculation changed in revision 5.1
Read Denali hardware revision number and use it to
calculate max_banks, The encoding of max_banks changed
in Denali revision 5.1.
[ Linux commit :
271707b1d817f5104e02b2bd1bab43f0c8759418 ]
Signed-off-by: Graham Moore <grmoore@opensource.altera.com>
[Brian: parentheses around macro arg]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[Masahiro: import from Linux and adjust ioread32() to readl() ]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tom Rini [Tue, 29 Mar 2016 17:33:13 +0000 (13:33 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-tegra
Tom Rini [Tue, 29 Mar 2016 16:58:45 +0000 (12:58 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq
Stephen Warren [Tue, 22 Mar 2016 15:45:36 +0000 (09:45 -0600)]
ARM: tegra210: set PLLE_PTS bit when enabling PLLE
This bit needs to be set for system suspend/resume to work. This setting
will be documented in an updated TRM at some time in the future.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Rai Harninder [Wed, 23 Mar 2016 11:34:38 +0000 (17:04 +0530)]
armv8/ls2080ardb: Enable VID support
This patch enable VID support for ls2080ardb platform.
It uses the common VID driver.
Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Qianyu Gong [Wed, 23 Mar 2016 11:11:36 +0000 (19:11 +0800)]
armv8/ls1043aqds: dts: Set SPI mode for DSPI
Clock phase and polarity for DSPI flash need to be set.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Mingkai Hu [Wed, 23 Mar 2016 11:10:43 +0000 (19:10 +0800)]
armv8: fsl-layerscape: Add LS1023A SVR
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Mingkai Hu [Wed, 23 Mar 2016 11:10:42 +0000 (19:10 +0800)]
armv8: fsl-layerscape: Fix LS1043A SVR register
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Saksham Jain [Wed, 23 Mar 2016 10:54:45 +0000 (16:24 +0530)]
SECURE BOOT: Change fsl_secboot_validate func to pass image addr
Use a pointer to pass image address to fsl_secboot_validate(),
instead of using environmental variable "img_addr".
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Saksham Jain [Wed, 23 Mar 2016 10:54:44 +0000 (16:24 +0530)]
SECURE BOOT: Halt execution when secure boot fail
In case of fatal failure during secure boot execution (e.g. header
not found), reset is asserted to stop execution. If the RESET_REQ
is not tied to HRESET, this allows the execution to continue.
Add esbh_halt() after the reset to make sure execution stops.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Saksham Jain [Wed, 23 Mar 2016 10:54:43 +0000 (16:24 +0530)]
SECURE_BOOT: Use default bootargs
For secure boot, currently we were using fixed bootargs for all SoCs.
This is not needed and we can use the bootargs which are used in
non-secure boot.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Saksham Jain [Wed, 23 Mar 2016 10:54:42 +0000 (16:24 +0530)]
crypto/fsl: Make CAAM transactions cacheable
This commit solves CAAM coherency issue on ls2080. When caches are
enabled and CAAM's DMA's AXI transcations are not made cacheable,
Core reads/writes data from/to caches and CAAM does from main memory.
This forces data flushes to synchronize various data structures. But
even if any data in proximity of these structures is read by core,
these structures again are fetched in caches.
To avoid this problem, either all the data that CAAM accesses can be
made cache line aligned or CAAM transcations can be made cacheable.
So, this commit makes CAAM transcations as write back with write and
read allocate.
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Saksham Jain [Wed, 23 Mar 2016 10:54:41 +0000 (16:24 +0530)]
crypto/fsl: Correct 64-bit write when MMU disabled
When MMU is disabled, 64-bit write must be aligned at 64-bit
boundary. Becaue the memory location is not guaranteed to be 64-bit
aligned, the 64-bit write needs to be split into two 32-bit writes
to avoid the alignment exception.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Saksham Jain [Wed, 23 Mar 2016 10:54:40 +0000 (16:24 +0530)]
armv8: fsl-lsch3: Disable SMMU during secure boot
During secure boot, SMMU is enabled on POR by SP bootrom. SMMU needs
to be put in bypass mode in uboot to enable CAAM transcations to pass
through.
For non-secure boot, SP BootROM doesn't enable SMMU, which is in
bypass mode out of reset.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Saksham Jain [Wed, 23 Mar 2016 10:54:39 +0000 (16:24 +0530)]
armv8: ls2080: Add config for endianess of CCSR GUR
The GUR (DCFG) registers in CCSR space are in little endian format.
Define a config CONFIG_SYS_FSL_CCSR_GUR_LE in
arch/arm/include/asm/arch-fsl-layerscape/config.h
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Saksham Jain [Wed, 23 Mar 2016 10:54:38 +0000 (16:24 +0530)]
armv8: ls2080: Change env variable "fdt_high"
"fdt_high" env variable was set to 0xcfffffff for secure boot.
Change it to 0xa0000000 for LS2080 to be consistent with non-secure
boot targets.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Saksham Jain [Wed, 23 Mar 2016 10:54:37 +0000 (16:24 +0530)]
armv8: fsl-lsch3: Copy Bootscript and header from NOR to DDR
To unify steps for secure boot for xip (eg. NOR) and non-xip memories
(eg. NAND, SD), bootscipts and its header are copied to main memory.
Validation and execution are performed from there.
For other ARM Platforms (ls1043 and ls1020), to avoid disruption of
existing users, this copy step is not used for NOR boot.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Saksham Jain [Wed, 23 Mar 2016 10:54:36 +0000 (16:24 +0530)]
armv8: ls2080: Add bootscript header addr for secure boot
During secure boot, Linux image along with other images are validated
using bootscript. This bootscript also needs to be validated before
it executes. This requires a header for bootscript.
When secure boot is enabled, default bootcmd is changed to first
validate bootscript using the header and then execute the script.
For ls2080, NOR memory map is different from other ARM SoCs. So a new
address on NOR is used for this bootscript header (0x583920000). The
Bootscript address is mentioned in this header along with addresses of
other images.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Saksham Jain [Wed, 23 Mar 2016 10:54:35 +0000 (16:24 +0530)]
armv8: ls2080rdb: ls2080qds: Add secure boot support
Sec_init has been called at the beginning to initialize SEC Block
(CAAM) which is used by secure boot validation later for both ls2080a
qds and rdb. 64-bit address in ESBC Header has been enabled. Secure
boot defconfigs are created for boards (NOR boot).
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Saksham Jain [Wed, 23 Mar 2016 10:54:34 +0000 (16:24 +0530)]
armv8: fsl-lsch3: Add new header for secure boot
For secure boot, a header is used to identify key table, signature
and image address. A new header structure is added for lsch3.
Currently key extension (IE) feature is not supported. Single key
feature is not supported. Keys must be in table format. Hence, SRK
(key table) must be present. Max key number has increase from 4 to
8. The 8th key is irrevocable. A new barker Code is used.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Saksham Jain [Wed, 23 Mar 2016 10:54:33 +0000 (16:24 +0530)]
armv8: ls2080: Add configs for SEC, SecMon, SRK and DCFG
Add configs for various IPs used during secure boot. Add address
and endianness for SEC and Security Monitor. SRK are fuses in SFP
(fuses for public key's hash). These are stored in little endian
format.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Saksham Jain [Wed, 23 Mar 2016 10:54:32 +0000 (16:24 +0530)]
armv8: ls2080: Add SFP Configs for LS2080
In LS2080, SFP has version 3.4. It is in little endian. The base
address is 0x01e80200. SFP is used in Secure Boot to read fuses.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Prabhakar Kushwaha [Fri, 18 Mar 2016 10:46:03 +0000 (16:16 +0530)]
driver: net: fsl-mc: Check NULL before pointer dereference
NULL pointer should be checked before any dereference. This patch
move memest after the NULL pointer check.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reported-by: Jose Rivera <german.rivera@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Prabhakar Kushwaha [Fri, 18 Mar 2016 10:45:29 +0000 (16:15 +0530)]
driver: net: fsl-mc: Free dflt_dpio pointer after its usage
Free dflt_dpio pointer after its usage during error handling
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reported-by: Jose Rivera <german.rivera@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Qianyu Gong [Wed, 16 Mar 2016 10:01:52 +0000 (18:01 +0800)]
armv8: fsl-layerscape: Skip reconfigure QSPI clock when booting from QSPI
The qspi_cfg register is set by PBI when booting from QSPI. No need
to changing it again.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Guy Thouret [Fri, 11 Mar 2016 16:23:41 +0000 (16:23 +0000)]
omap24xx_i2c: Implement CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
Signed-off-by: Guy Thouret <guy.thouret@wems.co.uk>
Cc: Heiko Schocher <hs@denx.de>
Peng Fan [Fri, 11 Mar 2016 08:47:50 +0000 (16:47 +0800)]
dm: i2c: mxc_i2c: implement i2c_idle_bus
Implement i2c_idle_bus in driver, then setup_i2c can
be dropped for boards which enable DM_I2C/DM_GPIO/PINCTRL.
The i2c_idle_bus force bus idle flow follows setup_i2c in
arch/arm/imx-common/i2c-mxv7.c
This patch is an implementation following linux kernel patch:
"
commit
1c4b6c3bcf30d0804db0d0647d8ebeb862c6f7e5
Author: Gao Pan <b54642@freescale.com>
Date: Fri Oct 23 20:28:54 2015 +0800
i2c: imx: implement bus recovery
Implement bus recovery methods for i2c-imx so we can recover from
situations where SCL/SDA are stuck low.
Once i2c bus SCL/SDA are stuck low during transfer, config the i2c
pinctrl to gpio mode by calling pinctrl sleep set function, and then
use GPIO to emulate the i2c protocol to send nine dummy clock to recover
i2c device. After recovery, set i2c pinctrl to default group setting.
"
See Documentation/devicetree/bindings/i2c/i2c-imx.txt for detailed
description.
1. Introuduce scl_gpio/sda_gpio/bus in mxc_i2c_bus.
2. Discard the __weak attribute for i2c_idle_bus and implement it,
since we have pinctrl driver/driver model gpio driver. We can
use device tree, but not let board code to do this.
3. gpio state for mxc_i2c is not a must, but it is recommended. If
there is no gpio state, driver will give tips, but not fail.
4. The i2c controller was first probed, default pinctrl state will
be used, so when need to use gpio function, need to do
"pinctrl_select_state(dev, "gpio")" and after force bus idle,
need to switch back "pinctrl_select_state(dev, "default")".
This is example about how to use the gpio force bus
idle function:
"
&i2c1 {
clock-frequency = <100000>;
pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c1>;
pinctrl-1 = <&pinctrl_i2c1_gpio>;
scl-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
sda-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
status = "okay";
[....]
};
[.....]
pinctrl_i2c1_gpio: i2c1grp_gpio {
fsl,pins = <
MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28 0x1b8b0
MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x1b8b0
>;
};
"
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: York Sun <york.sun@nxp.com>
Tom Rini [Mon, 28 Mar 2016 00:58:08 +0000 (20:58 -0400)]
Revert "pxa_lcd: make driver cache-aware"
This reverts commit
59deb7fe8d23c8ec2b659d99323ec4a2ec19148a.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Mon, 28 Mar 2016 00:57:54 +0000 (20:57 -0400)]
Revert "pxa_lcd: invert colors for Zipit Z2 to get white on black palette"
This reverts commit
3bc8ffd9cb774feceefc7bdebe9353fcea071343.
Signed-off-by: Tom Rini <trini@konsulko.com>
Andreas Fenkart [Fri, 25 Mar 2016 13:52:19 +0000 (14:52 +0100)]
tools: env: bug: config structs must be defined in tools library
fw_senten/fw_printenv can be compiled as a tools library,
excluding the fw_env_main object.
Reported-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Andreas Fenkart <andreas.fenkart@digitalstrom.com>
Lokesh Vutla [Thu, 24 Mar 2016 10:32:00 +0000 (16:02 +0530)]
ARM: asm: types: Introduce DMA_ADDR_T_64BIT
dma_addr_t holds any valid DMA address. If the DMA API only uses 32-bit
addresses, dma_addr_t need only be 32 bits wide. Bus addresses, e.g., PCI BARs,
may be wider than 32 bits, but drivers do memory-mapped I/O to ioremapped
kernel virtual addresses, so they don't care about the size of the actual
bus addresses.
Also 32 bit ARM systems with LPAE enabled can use 64bit address space, but
DMA still use 32bit address like in case of DRA7 and Keystone platforms.
This is inspired from the Linux kernel types implementation[1]
[1] https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/tree/include/linux/types.h#n142
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Alexander Graf [Thu, 24 Mar 2016 00:37:37 +0000 (01:37 +0100)]
efi_loader: Fix some entry/exit points
When switching between EFI context and U-Boot context we need to swap
the register that "gd" resides in.
Some functions slipped through here, with efi_allocate_pool / efi_free_pool
not doing the switch correctly and efi_return_handle switching too often.
Fix them all up to make sure we always have consistent register state.
Signed-off-by: Alexander Graf <agraf@suse.de>
Vasily Khoruzhick [Mon, 21 Mar 2016 01:37:10 +0000 (18:37 -0700)]
cfi_flash: return device into read array mode after reading status
Otherwise flash remains in read status mode and it's not possible
to access data on flash.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Vasily Khoruzhick [Mon, 21 Mar 2016 01:37:09 +0000 (18:37 -0700)]
zipitz2: enable caches
It speeds up loading kernel from SD or USB a lot.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Vasily Khoruzhick [Mon, 21 Mar 2016 01:37:08 +0000 (18:37 -0700)]
pxa_lcd: make driver cache-aware
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Vasily Khoruzhick [Mon, 21 Mar 2016 01:37:07 +0000 (18:37 -0700)]
pxa: add support for D- and I- caches
Tested with OHCI and pxafb drivers - no issues found
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Vasily Khoruzhick [Mon, 21 Mar 2016 01:37:06 +0000 (18:37 -0700)]
pxa: start.S: enable SRAM clock
SRAM is used for early stack, but kernel disables its clock on suspend.
Re-enable SRAM clock on startup, otherwise u-boot crashes on resume from suspend.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Vasily Khoruzhick [Mon, 21 Mar 2016 01:37:05 +0000 (18:37 -0700)]
zipitz2: enable USB host support
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Vasily Khoruzhick [Mon, 21 Mar 2016 01:37:04 +0000 (18:37 -0700)]
pxa-common: pxa27x has 3 OHCI ports
3rd port can be used as a device or host.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Vasily Khoruzhick [Mon, 21 Mar 2016 01:37:03 +0000 (18:37 -0700)]
zipitz2: enable libfdt
zipitz2 supports DT boot since linux-4.4 (not mainlined yet)
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Vasily Khoruzhick [Mon, 21 Mar 2016 01:37:02 +0000 (18:37 -0700)]
pxa_lcd: invert colors for Zipit Z2 to get white on black palette
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Vasily Khoruzhick [Mon, 21 Mar 2016 01:37:01 +0000 (18:37 -0700)]
zipitz2: enable LCD rotation
z2's screen is rotated by 270 degrees
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Vasily Khoruzhick [Mon, 21 Mar 2016 01:37:00 +0000 (18:37 -0700)]
zipitz2: restore board support
zipitz2 was dropped in
49d8899ba9c26335e4a12e01c18028fc5e40c796
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Peng Fan [Sun, 20 Mar 2016 13:21:36 +0000 (21:21 +0800)]
cmd: spi: check return value of strdup
Check return value of strdup.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Stephen Warren [Sat, 19 Mar 2016 03:41:38 +0000 (21:41 -0600)]
serial: add BCM283x mini UART driver
The RPi3 typically uses the regular UART for high-speed communication with
the Bluetooth device, leaving us the mini UART to use for the serial
console. Add support for this UART so we can use it.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Roger Quadros [Fri, 18 Mar 2016 11:18:12 +0000 (13:18 +0200)]
board: ti: am57xx: Set ethernet MAC addresses from EEPROM to env
The MAC addresses for the PRU Ethernet ports will be available in the
board EEPROM as an address range. Populate those MAC addresses (if valid)
into the u-boot environment so that they can be passed on to the
device tree during fdt_fixup_ethernet().
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Roger Quadros [Fri, 18 Mar 2016 11:18:11 +0000 (13:18 +0200)]
net: export eth_setenv_enetaddr_by_index() to net.h
Some TI boards (e.g. IDK) have 4 to 6 ethernet ports and
this function is handy at board.c to configure the
MAC address of the ports.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Bin Meng [Fri, 18 Mar 2016 06:59:04 +0000 (23:59 -0700)]
debug_uart: Remove duplicated carriage return handling
Since commit b391d74 "debug_uart: output CR along with LF", the
handling in puts() is duplicated, not to mention that it should
output carriage return before line feed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Bin Meng [Fri, 18 Mar 2016 06:59:03 +0000 (23:59 -0700)]
efi_stub: Move carriage return before line feed in putc()
A carriage return needs to execute before a line feed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Bin Meng [Fri, 18 Mar 2016 06:27:44 +0000 (23:27 -0700)]
net: rtl8169: Fix build error when DEBUG is on
When DEBUG_RTL8169 is on, a build error occurs in function
'rtl_init': error: 'dev' undeclared. Fix this.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Bin Meng [Fri, 18 Mar 2016 04:53:14 +0000 (21:53 -0700)]
mmc: Print send_cmd response only when return value is zero
send_cmd response is valid only when no error happened. If an error
occured, let mmc_send_cmd() print the return value to aid debugging.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Bin Meng [Fri, 18 Mar 2016 04:53:13 +0000 (21:53 -0700)]
mmc: Fix switch..case indention
Correct the indention level of switch..case statements.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Alexander Merkle [Thu, 17 Mar 2016 14:44:47 +0000 (15:44 +0100)]
Fix typo choosen in comments and printf logs
Minor change: chosen is written with one "o".
No code change here, only comment & printf.
Signed-off-by: Alexander Merkle <alexander.merkle@lauterbach.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Alexander Merkle [Thu, 17 Mar 2016 14:44:46 +0000 (15:44 +0100)]
Fix typo in chosen parameter of pcm052.dts
Fix typo "choosen" instead of "chosen" in pcm052.dts.
Not tested but should fix boot process and terminal output.
Signed-off-by: Alexander Merkle <alexander.merkle@lauterbach.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Alexander Merkle [Thu, 17 Mar 2016 14:44:45 +0000 (15:44 +0100)]
Fix typo in chosen parameter in vf610-twr.dts
Fix typo "choosen" instead of "chosen" in vf610-twr.dts.
Fixes boot process and terminal output for Vybrid series.
Signed-off-by: Alexander Merkle <alexander.merkle@lauterbach.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Anton Persson [Thu, 17 Mar 2016 08:38:21 +0000 (09:38 +0100)]
bootp: Prevent u-boot from using others responses.
In rare circumstances two dhcp clients may generate the same
bootp ID. If this happens it is vital that the client also checks
the hw address in the received response to prevent IP address conflicts.
Signed-off-by: Anton Persson <don.juanton@gmail.com>
Stephen Warren [Thu, 17 Mar 2016 03:42:24 +0000 (21:42 -0600)]
mmc: bcm2835: fix 64-bit build warning
Fixes:
drivers/mmc/bcm2835_sdhci.c: In function ‘bcm2835_sdhci_init’:
drivers/mmc/bcm2835_sdhci.c:181:17: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Stephen Warren [Thu, 17 Mar 2016 03:40:57 +0000 (21:40 -0600)]
ARM: bcm2835: fix 64-bit build warning in mbox
Fixes:
arch/arm/mach-bcm283x/mbox.c: In function ‘bcm2835_mbox_call_prop’:
arch/arm/mach-bcm283x/mbox.c:118:48: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
arch/arm/mach-bcm283x/mbox.c:126:29: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Stephen Warren [Thu, 17 Mar 2016 03:40:56 +0000 (21:40 -0600)]
ARM: bcm283x: don't always define CONFIG_BCM2835
Currently, CONFIG_BCM2835 is defined for all BCM283x builds and _BCM2836
is defined when building for that SoC. That means there isn't a single
define that means "exactly BCM2835". This will complicate future patches
where BCM2835-vs-anything-else needs to be determined simply.
Modify the code to define one or the other of CONFIG_BCM2835/BCM2836 so
future patches are simpler.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 17 Mar 2016 00:40:20 +0000 (20:40 -0400)]
doc/README.clang: Document sandbox instructions
It is possible to compile and run the sandbox target with clang
currently, so document that as well.
Cc: Jeroen Hofstee <jeroen@myspectrum.nl>
Signed-off-by: Tom Rini <trini@konsulko.com>
Alexander Graf [Thu, 24 Mar 2016 09:31:11 +0000 (10:31 +0100)]
bcm2835 video: Map fb as cached
The bcm2835 frame buffer is in RAM, so we can easily map it as cached and gain
all the glorious performance boost that brings with it.
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Alexander Graf [Wed, 16 Mar 2016 14:41:23 +0000 (15:41 +0100)]
RPi: Enable caches for rpi2
Now that we have support for running with caches enabled in HYP mode,
opt in to that on the Raspberry Pi 2. This brings a significant performance
boost.
Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Wed, 16 Mar 2016 14:41:22 +0000 (15:41 +0100)]
lcd: Fix compile warning in 64bit mode
When compiling the code for 64bit, the lcd code emits warnings because it
tries to cast pointers to 32bit values. Fix it by casting them to longs
instead, actually properly aligning with the function prototype.
Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Wed, 16 Mar 2016 14:41:21 +0000 (15:41 +0100)]
arm: Add support for HYP mode and LPAE page tables
We currently always modify the SVC versions of registers and only support
the short descriptor PTE format.
Some boards however (like the RPi2) run in HYP mode. There, we need to modify
the HYP version of system registers and HYP mode only supports the long
descriptor PTE format.
So this patch introduces support for both long descriptor PTEs and HYP mode
registers.
Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Wed, 16 Mar 2016 14:41:20 +0000 (15:41 +0100)]
arm64: Add 32bit arm compatible dcache definitions
We want to be able to reuse device drivers from 32bit code, so let's add
definitions for all the dcache options that 32bit code has.
While at it, fix up the DCACHE_OFF configuration. That was setting the bits
to declare a PTE a PTE and left the MAIR index bit at 0. Drop the useless
bits and make the index explicit.
Signed-off-by: Alexander Graf <agraf@suse.de>
Nishanth Menon [Tue, 15 Mar 2016 23:09:17 +0000 (18:09 -0500)]
board: ti: DRA7: Add DRA72-rev C evm pinmux
Add the pinmux data for rev C evm. This is different from previous
revisions of the platform thanks to the deltas introduced both from
silicon side and from SoC side.
Based on J6EcoES2_EVM_Base_Config-
20160309b and PCT-DRA72x-v1.3.0.7 for
SR2.0 silicon.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Nishanth Menon [Tue, 15 Mar 2016 23:09:16 +0000 (18:09 -0500)]
ARM: OMAP5/DRA7: Expose do_set_iodelay
do_set_iodelay can now be used from board files based on needs of the
platforms variation they have.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Nishanth Menon [Tue, 15 Mar 2016 23:09:15 +0000 (18:09 -0500)]
ARM: OMAP5/DRA7: Split iodelay functionality into sub steps
Since many platforms may need different pad configuration required
depending on variation of the platform with minor deltas, it is
easier to maintain a sub step based approach to allow for pin mux
and iodelay configuration which may depend on the platform variations
and need to be done in IO isolation.
While we retain the older __recalibrate_iodelay function which provides
a ready sequencing, __recalibrate_iodelay_start and
__recalibrate_iodelay_end may be alternatively used now and the callers
will be responsible for the correct sequencing of operations.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Ravi Babu [Tue, 15 Mar 2016 23:09:14 +0000 (18:09 -0500)]
board: ti: DRA72: revC evm: Update sdram timing configuration for SR2.0
DDR configuration has changes from SR1.1 based Rev-A/B version of evm
to the SR2.0 based Rev C of the EVM. Rev C evm now uses the higher
density MT41K512M8RH-125-AAT:E (IT) which is of size 2GB.
Update the DDR configuration based on data from EMIF configuration
tool 1.1.1. NOTE: we use eeprom information (ram_size) to update the
configuration.
Tested-by: Vishal Mahaveer <vishalm@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Nishanth Menon [Tue, 15 Mar 2016 23:09:13 +0000 (18:09 -0500)]
ARM: DRA72: sdram: Update sdram ext phy configuration for SR2.0
Based on data from EMIF configuration tool 1.1.1.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Nishanth Menon [Tue, 15 Mar 2016 23:09:12 +0000 (18:09 -0500)]
ARM: DRA7: hwdata: Update ioreg data for DRA72 SR2.0
Based on data from EMIF configuration tool 1.1.1. Expected update for
CTRL_WKUP_EMIF1_SDRAM_CONFIG_EXT in the next revision of the tool has
been incorporated as well.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Ravi Babu [Tue, 15 Mar 2016 23:09:11 +0000 (18:09 -0500)]
ARM: DRA72x: Add support for detection of SR2.0
Add support for detection of SR2.0 version of DRA72x family of
processors.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Alexander Graf [Tue, 15 Mar 2016 17:38:21 +0000 (18:38 +0100)]
efi_loader: Add GOP support
The EFI standard defines a simple boot protocol that an EFI payload can use
to access video output.
This patch adds support to expose exactly that one (and the mode already in
use) as possible graphical configuration to an EFI payload.
With this, I can successfully run grub2 with graphical output.
Signed-off-by: Alexander Graf <agraf@suse.de>
Nishanth Menon [Tue, 15 Mar 2016 15:25:53 +0000 (10:25 -0500)]
ARM: keystone2: Convert BOOT_SET_BITFIELD into static inline function
Fix up BOOT_SET_BITFIELD to be a static inline function to be readable
with the same functionality.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Nishanth Menon [Tue, 15 Mar 2016 15:25:52 +0000 (10:25 -0500)]
ARM: keystone2: Convert BOOT_READ_BITFIELD into static inline function
BOOT_READ_BITFIELD can easily be a static inline function and be a
little more readable with the same functionality.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Nishanth Menon [Tue, 15 Mar 2016 15:25:51 +0000 (10:25 -0500)]
ARM: keystone2: Convert BOOTBITMASK to static inline function
BOOTBITMASK is almost impossible to decode, so convert it into a simpler
static line functions of equivalent solution.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Andreas Fenkart [Fri, 11 Mar 2016 08:39:38 +0000 (09:39 +0100)]
tools: env: fw_parse_script: simplify removal of newline/carriage return
fgets returns when the first '\n' is found
Signed-off-by: Andreas Fenkart <andreas.fenkart@digitalstrom.com>
Andreas Fenkart [Fri, 11 Mar 2016 08:39:37 +0000 (09:39 +0100)]
tools: env: split fw_string_blank into skip_chars / skip_blanks
Signed-off-by: Andreas Fenkart <andreas.fenkart@digitalstrom.com>
Andreas Fenkart [Fri, 11 Mar 2016 08:39:36 +0000 (09:39 +0100)]
tools: env: fw_string_blank: return from loop when item found
Signed-off-by: Andreas Fenkart <andreas.fenkart@digitalstrom.com>
Andreas Fenkart [Fri, 11 Mar 2016 08:39:35 +0000 (09:39 +0100)]
tools: env: replace WHITESPACE macro by isblank
Signed-off-by: Andreas Fenkart <andreas.fenkart@digitalstrom.com>
Vikas Manocha [Wed, 9 Mar 2016 23:18:14 +0000 (15:18 -0800)]
stm32f746-disco: enable flash support
This patch enables embedded flash for stm32f746 discovery board.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Vikas Manocha [Wed, 9 Mar 2016 23:18:13 +0000 (15:18 -0800)]
stm32: stm32f4: move flash driver to mtd driver location
Same flash driver can be used by other stm32 families like stm32f7.
Better place for this driver would be mtd driver location.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>