Zhang Changzhong [Thu, 14 Oct 2021 09:26:40 +0000 (17:26 +0800)]
can: j1939: j1939_xtp_rx_rts_session_new(): abort TP less than 9 bytes
The receiver should abort TP if 'total message size' in TP.CM_RTS and
TP.CM_BAM is less than 9 or greater than 1785 [1], but currently the
j1939 stack only checks the upper bound and the receiver will accept
the following broadcast message:
vcan1
18ECFF00 [8] 20 08 00 02 FF 00 23 01
vcan1
18EBFF00 [8] 01 00 00 00 00 00 00 00
vcan1
18EBFF00 [8] 02 00 FF FF FF FF FF FF
This patch adds check for the lower bound and abort illegal TP.
[1] SAE-J1939-82 A.3.4 Row 2 and A.3.6 Row 6.
Fixes:
9d71dd0c7009 ("can: add support of SAE J1939 protocol")
Link: https://lore.kernel.org/all/1634203601-3460-1-git-send-email-zhangchangzhong@huawei.com
Cc: stable@vger.kernel.org
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Zhang Changzhong [Thu, 30 Sep 2021 03:33:20 +0000 (11:33 +0800)]
can: j1939: j1939_xtp_rx_dat_one(): cancel session if receive TP.DT with error length
According to SAE-J1939-21, the data length of TP.DT must be 8 bytes, so
cancel session when receive unexpected TP.DT message.
Fixes:
9d71dd0c7009 ("can: add support of SAE J1939 protocol")
Link: https://lore.kernel.org/all/1632972800-45091-1-git-send-email-zhangchangzhong@huawei.com
Cc: stable@vger.kernel.org
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Ziyang Xuan [Sun, 26 Sep 2021 10:47:57 +0000 (18:47 +0800)]
can: j1939: j1939_netdev_start(): fix UAF for rx_kref of j1939_priv
It will trigger UAF for rx_kref of j1939_priv as following.
cpu0 cpu1
j1939_sk_bind(socket0, ndev0, ...)
j1939_netdev_start
j1939_sk_bind(socket1, ndev0, ...)
j1939_netdev_start
j1939_priv_set
j1939_priv_get_by_ndev_locked
j1939_jsk_add
.....
j1939_netdev_stop
kref_put_lock(&priv->rx_kref, ...)
kref_get(&priv->rx_kref, ...)
REFCOUNT_WARN("addition on 0;...")
====================================================
refcount_t: addition on 0; use-after-free.
WARNING: CPU: 1 PID: 20874 at lib/refcount.c:25 refcount_warn_saturate+0x169/0x1e0
RIP: 0010:refcount_warn_saturate+0x169/0x1e0
Call Trace:
j1939_netdev_start+0x68b/0x920
j1939_sk_bind+0x426/0xeb0
? security_socket_bind+0x83/0xb0
The rx_kref's kref_get() and kref_put() should use j1939_netdev_lock to
protect.
Fixes:
9d71dd0c70099 ("can: add support of SAE J1939 protocol")
Link: https://lore.kernel.org/all/20210926104757.2021540-1-william.xuanziyang@huawei.com
Cc: stable@vger.kernel.org
Reported-by: syzbot+85d9878b19c94f9019ad@syzkaller.appspotmail.com
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Ziyang Xuan [Mon, 6 Sep 2021 09:42:19 +0000 (17:42 +0800)]
can: j1939: j1939_tp_rxtimer(): fix errant alert in j1939_tp_rxtimer
When the session state is J1939_SESSION_DONE, j1939_tp_rxtimer() will
give an alert "rx timeout, send abort", but do nothing actually. Move
the alert into session active judgment condition, it is more
reasonable.
One of the scenarios is that j1939_tp_rxtimer() execute followed by
j1939_xtp_rx_abort_one(). After j1939_xtp_rx_abort_one(), the session
state is J1939_SESSION_DONE, then j1939_tp_rxtimer() give an alert.
Fixes:
9d71dd0c7009 ("can: add support of SAE J1939 protocol")
Link: https://lore.kernel.org/all/20210906094219.95924-1-william.xuanziyang@huawei.com
Cc: stable@vger.kernel.org
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Nikolay Aleksandrov [Fri, 15 Oct 2021 09:05:46 +0000 (12:05 +0300)]
net: bridge: mcast: use multicast_membership_interval for IGMPv3
When I added IGMPv3 support I decided to follow the RFC for computing
the GMI dynamically:
" 8.4. Group Membership Interval
The Group Membership Interval is the amount of time that must pass
before a multicast router decides there are no more members of a
group or a particular source on a network.
This value MUST be ((the Robustness Variable) times (the Query
Interval)) plus (one Query Response Interval)."
But that actually is inconsistent with how the bridge used to compute it
for IGMPv2, where it was user-configurable that has a correct default value
but it is up to user-space to maintain it. This would make it consistent
with the other timer values which are also maintained correct by the user
instead of being dynamically computed. It also changes back to the previous
user-expected GMI behaviour for IGMPv3 queries which were supported before
IGMPv3 was added. Note that to properly compute it dynamically we would
need to add support for "Robustness Variable" which is currently missing.
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Fixes:
0436862e417e ("net: bridge: mcast: support for IGMPv3/MLDv2 ALLOW_NEW_SOURCES report")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano Garzarella [Thu, 14 Oct 2021 15:20:45 +0000 (17:20 +0200)]
vsock_diag_test: remove free_sock_stat() call in test_no_sockets
In `test_no_sockets` we don't expect any sockets, indeed
check_no_sockets() prints an error and exits if `sockets` list is
not empty, so free_sock_stat() call is unnecessary since it would
only be called when the `sockets` list is empty.
This was discovered by a strange warning printed by gcc v11.2.1:
In file included from ../../include/linux/list.h:7,
from vsock_diag_test.c:18:
vsock_diag_test.c: In function ‘test_no_sockets’:
../../include/linux/kernel.h:35:45: error: array subscript ‘struct vsock_stat[0]’ is partly outside array bound
s of ‘struct list_head[1]’ [-Werror=array-bounds]
35 | const typeof(((type *)0)->member) * __mptr = (ptr); \
| ^~~~~~
../../include/linux/list.h:352:9: note: in expansion of macro ‘container_of’
352 | container_of(ptr, type, member)
| ^~~~~~~~~~~~
../../include/linux/list.h:393:9: note: in expansion of macro ‘list_entry’
393 | list_entry((pos)->member.next, typeof(*(pos)), member)
| ^~~~~~~~~~
../../include/linux/list.h:522:21: note: in expansion of macro ‘list_next_entry’
522 | n = list_next_entry(pos, member); \
| ^~~~~~~~~~~~~~~
vsock_diag_test.c:325:9: note: in expansion of macro ‘list_for_each_entry_safe’
325 | list_for_each_entry_safe(st, next, sockets, list) {
| ^~~~~~~~~~~~~~~~~~~~~~~~
In file included from vsock_diag_test.c:18:
vsock_diag_test.c:333:19: note: while referencing ‘sockets’
333 | LIST_HEAD(sockets);
| ^~~~~~~
../../include/linux/list.h:23:26: note: in definition of macro ‘LIST_HEAD’
23 | struct list_head name = LIST_HEAD_INIT(name)
It seems related to some compiler optimization and assumption
about the empty `sockets` list, since this warning is printed
only with -02 or -O3. Also removing `exit(1)` from
check_no_sockets() makes the warning disappear since in that
case free_sock_stat() can be reached also when the list is
not empty.
Reported-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20211014152045.173872-1-sgarzare@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Sat, 16 Oct 2021 00:20:15 +0000 (17:20 -0700)]
Merge branch '100GbE' of git://git./linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-10-14
Brett ensures RDMA nodes are removed during release and rebuild. He also
corrects fw.mgmt.api to include the patch number for proper
identification.
Dave stops ida_free() being called when an IDA has not been allocated.
Michal corrects the order of parameters being provided and the number of
entries skipped for UDP tunnels.
====================
Link: https://lore.kernel.org/r/20211014181953.3538330-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stephen Suryaputra [Thu, 14 Oct 2021 13:08:45 +0000 (09:08 -0400)]
ipv6: When forwarding count rx stats on the orig netdev
Commit
bdb7cc643fc9 ("ipv6: Count interface receive statistics on the
ingress netdev") does not work when ip6_forward() executes on the skbs
with vrf-enslaved netdev. Use IP6CB(skb)->iif to get to the right one.
Add a selftest script to verify.
Fixes:
bdb7cc643fc9 ("ipv6: Count interface receive statistics on the ingress netdev")
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20211014130845.410602-1-ssuryaextr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
David S. Miller [Fri, 15 Oct 2021 13:36:57 +0000 (14:36 +0100)]
Merge branch 'tcp-md5-vrf-fix'
Leonard Crestez says:
====================
tcp: md5: Fix overlap between vrf and non-vrf keys
With net.ipv4.tcp_l3mdev_accept=1 it is possible for a listen socket to
accept connection from the same client address in different VRFs. It is
also possible to set different MD5 keys for these clients which differ only
in the tcpm_l3index field.
This appears to work when distinguishing between different VRFs but not
between non-VRF and VRF connections. In particular:
* tcp_md5_do_lookup_exact will match a non-vrf key against a vrf key. This
means that adding a key with l3index != 0 after a key with l3index == 0
will cause the earlier key to be deleted. Both keys can be present if the
non-vrf key is added later.
* _tcp_md5_do_lookup can match a non-vrf key before a vrf key. This casues
failures if the passwords differ.
This can be fixed by making tcp_md5_do_lookup_exact perform an actual exact
comparison on l3index and by making __tcp_md5_do_lookup perfer vrf-bound
keys above other considerations like prefixlen.
The fact that keys with l3index==0 affect VRF connections is usually not
desirable, VRFs are meant to be completely independent. This behavior needs
to preserved for backwards compatibility. Also, applications can just bind
listen sockets to VRF and never specify TCP_MD5SIG_FLAG_IFINDEX at all.
So far the combination of TCP_MD5SIG_FLAG_IFINDEX with tcpm_ifindex == 0
was an error, accept this to mean "key only applies to default VRF". This
is what applications using VRFs for traffic separation want.
This also contains tests for the second part. It does not contain tests for
overlapping keys, that would require more changes in nettest to add
multiple keys. These scenarios are also covered by my tests for TCP-AO,
especially around this area:
https://github.com/cdleonard/tcp-authopt-test/blob/main/tcp_authopt_test/test_vrf_bind.py
Changes since V2:
* Rename --do-bind-key-ifindex to --force-bind-key-ifindex
* Fix referencing TCP_MD5SIG_FLAG_IFINDEX as TCP_MD5SIG_IFINDEX
Link to v2: https://lore.kernel.org/netdev/cover.
1634107317.git.cdleonard@gmail.com/
Changes since V1:
* Accept (TCP_MD5SIG_IFINDEX with tcpm_ifindex == 0)
* Add flags for explicitly including or excluding TCP_MD5SIG_FLAG_IFINDEX
to nettest
* Add few more tests in fcnal-test.sh.
Link to v1: https://lore.kernel.org/netdev/
3d8387d499f053dba5cd9184c0f7b8445c4470c6.
1633542093.git.cdleonard@gmail.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Leonard Crestez [Fri, 15 Oct 2021 07:26:07 +0000 (10:26 +0300)]
selftests: net/fcnal: Test --{force,no}-bind-key-ifindex
Test that applications binding listening sockets to VRFs without
specifying TCP_MD5SIG_FLAG_IFINDEX will work as expected. This would
be broken if __tcp_md5_do_lookup always made a strict comparison on
l3index. See this email:
https://lore.kernel.org/netdev/
209548b5-27d2-2059-f2e9-
2148f5a0291b@gmail.com/
Applications using tcp_l3mdev_accept=1 and a single global socket (not
bound to any interface) also should have a way to specify keys that are
only for the default VRF, this is done by --force-bind-key-ifindex
without otherwise binding to a device.
Signed-off-by: Leonard Crestez <cdleonard@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leonard Crestez [Fri, 15 Oct 2021 07:26:06 +0000 (10:26 +0300)]
selftests: nettest: Add --{force,no}-bind-key-ifindex
These options allow explicit control over the TCP_MD5SIG_FLAG_IFINDEX
flag instead of always setting it based on binding to an interface.
Do this by converting to getopt_long because nettest has too many
single-character flags already and getopt_long is widely used in
selftests.
Signed-off-by: Leonard Crestez <cdleonard@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leonard Crestez [Fri, 15 Oct 2021 07:26:05 +0000 (10:26 +0300)]
tcp: md5: Allow MD5SIG_FLAG_IFINDEX with ifindex=0
Multiple VRFs are generally meant to be "separate" but right now md5
keys for the default VRF also affect connections inside VRFs if the IP
addresses happen to overlap.
So far the combination of TCP_MD5SIG_FLAG_IFINDEX with tcpm_ifindex == 0
was an error, accept this to mean "key only applies to default VRF".
This is what applications using VRFs for traffic separation want.
Signed-off-by: Leonard Crestez <cdleonard@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leonard Crestez [Fri, 15 Oct 2021 07:26:04 +0000 (10:26 +0300)]
tcp: md5: Fix overlap between vrf and non-vrf keys
With net.ipv4.tcp_l3mdev_accept=1 it is possible for a listen socket to
accept connection from the same client address in different VRFs. It is
also possible to set different MD5 keys for these clients which differ
only in the tcpm_l3index field.
This appears to work when distinguishing between different VRFs but not
between non-VRF and VRF connections. In particular:
* tcp_md5_do_lookup_exact will match a non-vrf key against a vrf key.
This means that adding a key with l3index != 0 after a key with l3index
== 0 will cause the earlier key to be deleted. Both keys can be present
if the non-vrf key is added later.
* _tcp_md5_do_lookup can match a non-vrf key before a vrf key. This
casues failures if the passwords differ.
Fix this by making tcp_md5_do_lookup_exact perform an actual exact
comparison on l3index and by making __tcp_md5_do_lookup perfer
vrf-bound keys above other considerations like prefixlen.
Fixes:
dea53bb80e07 ("tcp: Add l3index to tcp_md5sig_key and md5 functions")
Signed-off-by: Leonard Crestez <cdleonard@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vegard Nossum [Fri, 15 Oct 2021 13:07:54 +0000 (15:07 +0200)]
lan78xx: select CRC32
Fix the following build/link error by adding a dependency on the CRC32
routines:
ld: drivers/net/usb/lan78xx.o: in function `lan78xx_set_multicast':
lan78xx.c:(.text+0x48cf): undefined reference to `crc32_le'
The actual use of crc32_le() comes indirectly through ether_crc().
Fixes:
55d7de9de6c30 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Thu, 14 Oct 2021 04:50:55 +0000 (00:50 -0400)]
sctp: fix transport encap_port update in sctp_vtag_verify
transport encap_port update should be updated when sctp_vtag_verify()
succeeds, namely, returns 1, not returns 0. Correct it in this patch.
While at it, also fix the indentation.
Fixes:
a1dd2cf2f1ae ("sctp: allow changing transport encap_port by peer packets")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kele Huang [Thu, 14 Oct 2021 03:19:52 +0000 (11:19 +0800)]
ptp: fix error print of ptp_kvm on X86_64 platform
Commit
a86ed2cfa13c5 ("ptp: Don't print an error if ptp_kvm is not supported")
fixes the error message print on ARM platform by only concerning about
the case that the error returned from kvm_arch_ptp_init() is not -EOPNOTSUPP.
Although the ARM platform returns -EOPNOTSUPP if ptp_kvm is not supported
while X86_64 platform returns -KVM_EOPNOTSUPP, both error codes share the
same value 95.
Actually kvm_arch_ptp_init() on X86_64 platform can return three kinds of
errors (-KVM_ENOSYS, -KVM_EOPNOTSUPP and -KVM_EFAULT). The problem is that
-KVM_EOPNOTSUPP is masked out and -KVM_EFAULT is ignored among them.
This patch fixes this by returning them to ptp_kvm_init() respectively.
Signed-off-by: Kele Huang <huangkele@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 14 Oct 2021 22:21:39 +0000 (18:21 -0400)]
Merge tag 'net-5.15-rc6' of git://git./linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Quite calm.
The noisy DSA driver (embedded switches) changes, and adjustment to
IPv6 IOAM behavior add to diffstat's bottom line but are not scary.
Current release - regressions:
- af_unix: rename UNIX-DGRAM to UNIX to maintain backwards
compatibility
- procfs: revert "add seq_puts() statement for dev_mcast", minor
format change broke user space
Current release - new code bugs:
- dsa: fix bridge_num not getting cleared after ports leaving the
bridge, resource leak
- dsa: tag_dsa: send packets with TX fwd offload from VLAN-unaware
bridges using VID 0, prevent packet drops if pvid is removed
- dsa: mv88e6xxx: keep the pvid at 0 when VLAN-unaware, prevent HW
getting confused about station to VLAN mapping
Previous releases - regressions:
- virtio-net: fix for skb_over_panic inside big mode
- phy: do not shutdown PHYs in READY state
- dsa: mv88e6xxx: don't use PHY_DETECT on internal PHY's, fix link
LED staying lit after ifdown
- mptcp: fix possible infinite wait on recvmsg(MSG_WAITALL)
- mqprio: Correct stats in mqprio_dump_class_stats()
- ice: fix deadlock for Tx timestamp tracking flush
- stmmac: fix feature detection on old hardware
Previous releases - always broken:
- sctp: account stream padding length for reconf chunk
- icmp: fix icmp_ext_echo_iio parsing in icmp_build_probe()
- isdn: cpai: check ctr->cnr to avoid array index out of bound
- isdn: mISDN: fix sleeping function called from invalid context
- nfc: nci: fix potential UAF of rf_conn_info object
- dsa: microchip: prevent ksz_mib_read_work from kicking back in
after it's canceled in .remove and crashing
- dsa: mv88e6xxx: isolate the ATU databases of standalone and bridged
ports
- dsa: sja1105, ocelot: break circular dependency between switch and
tag drivers
- dsa: felix: improve timestamping in presence of packe loss
- mlxsw: thermal: fix out-of-bounds memory accesses
Misc:
- ipv6: ioam: move the check for undefined bits to improve
interoperability"
* tag 'net-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (60 commits)
icmp: fix icmp_ext_echo_iio parsing in icmp_build_probe
MAINTAINERS: Update the devicetree documentation path of imx fec driver
sctp: account stream padding length for reconf chunk
mlxsw: thermal: Fix out-of-bounds memory accesses
ethernet: s2io: fix setting mac address during resume
NFC: digital: fix possible memory leak in digital_in_send_sdd_req()
NFC: digital: fix possible memory leak in digital_tg_listen_mdaa()
nfc: fix error handling of nfc_proto_register()
Revert "net: procfs: add seq_puts() statement for dev_mcast"
net: encx24j600: check error in devm_regmap_init_encx24j600
net: korina: select CRC32
net: arc: select CRC32
net: dsa: felix: break at first CPU port during init and teardown
net: dsa: tag_ocelot_8021q: fix inability to inject STP BPDUs into BLOCKING ports
net: dsa: felix: purge skb from TX timestamping queue if it cannot be sent
net: dsa: tag_ocelot_8021q: break circular dependency with ocelot switch lib
net: dsa: tag_ocelot: break circular dependency with ocelot switch lib driver
net: mscc: ocelot: cross-check the sequence id from the timestamp FIFO with the skb PTP header
net: mscc: ocelot: deny TX timestamping of non-PTP packets
net: mscc: ocelot: warn when a PTP IRQ is raised for an unknown skb
...
Brett Creeley [Mon, 27 Sep 2021 18:21:50 +0000 (11:21 -0700)]
ice: Print the api_patch as part of the fw.mgmt.api
Currently when a user uses "devlink dev info", the fw.mgmt.api will be
the major.minor numbers as shown below:
devlink dev info pci/0000:3b:00.0
pci/0000:3b:00.0:
driver ice
serial_number 00-01-00-ff-ff-00-00-00
versions:
fixed:
board.id K91258-000
running:
fw.mgmt 6.1.2
fw.mgmt.api 1.7 <--- No patch number included
fw.mgmt.build 0xd75e7d06
fw.mgmt.srev 5
fw.undi 1.2992.0
fw.undi.srev 5
fw.psid.api 3.10
fw.bundle_id 0x800085cc
fw.app.name ICE OS Default Package
fw.app 1.3.27.0
fw.app.bundle_id 0xc0000001
fw.netlist 3.10.2000-3.1e.0
fw.netlist.build 0x2a76e110
stored:
fw.mgmt.srev 5
fw.undi 1.2992.0
fw.undi.srev 5
fw.psid.api 3.10
fw.bundle_id 0x800085cc
fw.netlist 3.10.2000-3.1e.0
fw.netlist.build 0x2a76e110
There are many features in the driver that depend on the major, minor,
and patch version of the FW. Without the patch number in the output for
fw.mgmt.api debugging issues related to the FW API version is difficult.
Also, using major.minor.patch aligns with the existing firmware version
which uses a 3 digit value.
Fix this by making the fw.mgmt.api print the major.minor.patch
versions. Shown below is the result:
devlink dev info pci/0000:3b:00.0
pci/0000:3b:00.0:
driver ice
serial_number 00-01-00-ff-ff-00-00-00
versions:
fixed:
board.id K91258-000
running:
fw.mgmt 6.1.2
fw.mgmt.api 1.7.9 <--- patch number included
fw.mgmt.build 0xd75e7d06
fw.mgmt.srev 5
fw.undi 1.2992.0
fw.undi.srev 5
fw.psid.api 3.10
fw.bundle_id 0x800085cc
fw.app.name ICE OS Default Package
fw.app 1.3.27.0
fw.app.bundle_id 0xc0000001
fw.netlist 3.10.2000-3.1e.0
fw.netlist.build 0x2a76e110
stored:
fw.mgmt.srev 5
fw.undi 1.2992.0
fw.undi.srev 5
fw.psid.api 3.10
fw.bundle_id 0x800085cc
fw.netlist 3.10.2000-3.1e.0
fw.netlist.build 0x2a76e110
Fixes:
ff2e5c700e08 ("ice: add basic handler for devlink .info_get")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Michal Swiatkowski [Tue, 14 Sep 2021 23:25:05 +0000 (19:25 -0400)]
ice: fix getting UDP tunnel entry
Correct parameters order in call to ice_tunnel_idx_to_entry function.
Entry in sparse port table is correct when the idx is 0. For idx 1 one
correct entry should be skipped, for idx 2 two of them should be skipped
etc. Change if condition to be true when idx is 0, which means that
previous valid entry of this tunnel type were skipped.
Fixes:
b20e6c17c468 ("ice: convert to new udp_tunnel infrastructure")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Dave Ertman [Mon, 4 Oct 2021 12:15:25 +0000 (05:15 -0700)]
ice: Avoid crash from unnecessary IDA free
In the remove path, there is an attempt to free the aux_idx IDA whether
it was allocated or not. This can potentially cause a crash when
unloading the driver on systems that do not initialize support for RDMA.
But, this free cannot be gated by the status bit for RDMA, since it is
allocated if the driver detects support for RDMA at probe time, but the
driver can enter into a state where RDMA is not supported after the IDA
has been allocated at probe time and this would lead to a memory leak.
Initialize aux_idx to an invalid value and check for a valid value when
unloading to determine if an IDA free is necessary.
Fixes:
d25a0fc41c1f9 ("ice: Initialize RDMA support")
Reported-by: Jun Miao <jun.miao@windriver.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Brett Creeley [Mon, 28 Jun 2021 17:53:45 +0000 (10:53 -0700)]
ice: Fix failure to re-add LAN/RDMA Tx queues
Currently if the VSI is rebuilt/removed and the RDMA PF driver is active
the RDMA Tx queue scheduler node configuration will not be cleaned up.
This will cause the rebuild/re-add of the VSI to fail due to the
software structures not being correctly cleaned up for the VSI index.
Fix this by always calling ice_rm_vsi_rdma_cfg() for all VSI. If there
are no RDMA scheduler nodes created, then there is no harm in calling
ice_rm_vsi_rdma_cfg(). This change applies to all VSI types, so if
RDMA support is added for other VSI types they will also get this
change.
Fixes:
348048e724a0 ("ice: Implement iidc operations")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Jerzy Wiktor Jurkowski <jerzy.wiktor.jurkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Xin Long [Thu, 14 Oct 2021 09:50:50 +0000 (05:50 -0400)]
icmp: fix icmp_ext_echo_iio parsing in icmp_build_probe
In icmp_build_probe(), the icmp_ext_echo_iio parsing should be done
step by step and skb_header_pointer() return value should always be
checked, this patch fixes 3 places in there:
- On case ICMP_EXT_ECHO_CTYPE_NAME, it should only copy ident.name
from skb by skb_header_pointer(), its len is ident_len. Besides,
the return value of skb_header_pointer() should always be checked.
- On case ICMP_EXT_ECHO_CTYPE_INDEX, move ident_len check ahead of
skb_header_pointer(), and also do the return value check for
skb_header_pointer().
- On case ICMP_EXT_ECHO_CTYPE_ADDR, before accessing iio->ident.addr.
ctype3_hdr.addrlen, skb_header_pointer() should be called first,
then check its return value and ident_len.
On subcases ICMP_AFI_IP and ICMP_AFI_IP6, also do check for ident.
addr.ctype3_hdr.addrlen and skb_header_pointer()'s return value.
On subcase ICMP_AFI_IP, the len for skb_header_pointer() should be
"sizeof(iio->extobj_hdr) + sizeof(iio->ident.addr.ctype3_hdr) +
sizeof(struct in_addr)" or "ident_len".
v1->v2:
- To make it more clear, call skb_header_pointer() once only for
iio->indent's parsing as Jakub Suggested.
v2->v3:
- The extobj_hdr.length check against sizeof(_iio) should be done
before calling skb_header_pointer(), as Eric noticed.
Fixes:
d329ea5bd884 ("icmp: add response to RFC 8335 PROBE messages")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/31628dd76657ea62f5cf78bb55da6b35240831f1.1634205050.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cai Huoqing [Thu, 14 Oct 2021 11:02:14 +0000 (19:02 +0800)]
MAINTAINERS: Update the devicetree documentation path of imx fec driver
Change the devicetree documentation path
to "Documentation/devicetree/bindings/net/fsl,fec.yaml"
since 'fsl-fec.txt' has been converted to 'fsl,fec.yaml' already.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20211014110214.3254-1-caihuoqing@baidu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eiichi Tsukata [Wed, 13 Oct 2021 20:27:29 +0000 (17:27 -0300)]
sctp: account stream padding length for reconf chunk
sctp_make_strreset_req() makes repeated calls to sctp_addto_chunk()
which will automatically account for padding on each call. inreq and
outreq are already 4 bytes aligned, but the payload is not and doing
SCTP_PAD4(a + b) (which _sctp_make_chunk() did implicitly here) is
different from SCTP_PAD4(a) + SCTP_PAD4(b) and not enough. It led to
possible attempt to use more buffer than it was allocated and triggered
a BUG_ON.
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Fixes:
cc16f00f6529 ("sctp: add support for generating stream reconf ssn reset request chunk")
Reported-by: Eiichi Tsukata <eiichi.tsukata@nutanix.com>
Signed-off-by: Eiichi Tsukata <eiichi.tsukata@nutanix.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/b97c1f8b0c7ff79ac4ed206fc2c49d3612e0850c.1634156849.git.mleitner@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ido Schimmel [Tue, 12 Oct 2021 17:49:55 +0000 (20:49 +0300)]
mlxsw: thermal: Fix out-of-bounds memory accesses
Currently, mlxsw allows cooling states to be set above the maximum
cooling state supported by the driver:
# cat /sys/class/thermal/thermal_zone2/cdev0/type
mlxsw_fan
# cat /sys/class/thermal/thermal_zone2/cdev0/max_state
10
# echo 18 > /sys/class/thermal/thermal_zone2/cdev0/cur_state
# echo $?
0
This results in out-of-bounds memory accesses when thermal state
transition statistics are enabled (CONFIG_THERMAL_STATISTICS=y), as the
transition table is accessed with a too large index (state) [1].
According to the thermal maintainer, it is the responsibility of the
driver to reject such operations [2].
Therefore, return an error when the state to be set exceeds the maximum
cooling state supported by the driver.
To avoid dead code, as suggested by the thermal maintainer [3],
partially revert commit
a421ce088ac8 ("mlxsw: core: Extend cooling
device with cooling levels") that tried to interpret these invalid
cooling states (above the maximum) in a special way. The cooling levels
array is not removed in order to prevent the fans going below 20% PWM,
which would cause them to get stuck at 0% PWM.
[1]
BUG: KASAN: slab-out-of-bounds in thermal_cooling_device_stats_update+0x271/0x290
Read of size 4 at addr
ffff8881052f7bf8 by task kworker/0:0/5
CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.15.0-rc3-custom-45935-gce1adf704b14 #122
Hardware name: Mellanox Technologies Ltd. "MSN2410-CB2FO"/"SA000874", BIOS 4.6.5 03/08/2016
Workqueue: events_freezable_power_ thermal_zone_device_check
Call Trace:
dump_stack_lvl+0x8b/0xb3
print_address_description.constprop.0+0x1f/0x140
kasan_report.cold+0x7f/0x11b
thermal_cooling_device_stats_update+0x271/0x290
__thermal_cdev_update+0x15e/0x4e0
thermal_cdev_update+0x9f/0xe0
step_wise_throttle+0x770/0xee0
thermal_zone_device_update+0x3f6/0xdf0
process_one_work+0xa42/0x1770
worker_thread+0x62f/0x13e0
kthread+0x3ee/0x4e0
ret_from_fork+0x1f/0x30
Allocated by task 1:
kasan_save_stack+0x1b/0x40
__kasan_kmalloc+0x7c/0x90
thermal_cooling_device_setup_sysfs+0x153/0x2c0
__thermal_cooling_device_register.part.0+0x25b/0x9c0
thermal_cooling_device_register+0xb3/0x100
mlxsw_thermal_init+0x5c5/0x7e0
__mlxsw_core_bus_device_register+0xcb3/0x19c0
mlxsw_core_bus_device_register+0x56/0xb0
mlxsw_pci_probe+0x54f/0x710
local_pci_probe+0xc6/0x170
pci_device_probe+0x2b2/0x4d0
really_probe+0x293/0xd10
__driver_probe_device+0x2af/0x440
driver_probe_device+0x51/0x1e0
__driver_attach+0x21b/0x530
bus_for_each_dev+0x14c/0x1d0
bus_add_driver+0x3ac/0x650
driver_register+0x241/0x3d0
mlxsw_sp_module_init+0xa2/0x174
do_one_initcall+0xee/0x5f0
kernel_init_freeable+0x45a/0x4de
kernel_init+0x1f/0x210
ret_from_fork+0x1f/0x30
The buggy address belongs to the object at
ffff8881052f7800
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 1016 bytes inside of
1024-byte region [
ffff8881052f7800,
ffff8881052f7c00)
The buggy address belongs to the page:
page:
0000000052355272 refcount:1 mapcount:0 mapping:
0000000000000000 index:0x0 pfn:0x1052f0
head:
0000000052355272 order:3 compound_mapcount:0 compound_pincount:0
flags: 0x200000000010200(slab|head|node=0|zone=2)
raw:
0200000000010200 ffffea0005034800 0000000300000003 ffff888100041dc0
raw:
0000000000000000 0000000000100010 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8881052f7a80: 00 00 00 00 00 00 04 fc fc fc fc fc fc fc fc fc
ffff8881052f7b00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>
ffff8881052f7b80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
ffff8881052f7c00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff8881052f7c80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[2] https://lore.kernel.org/linux-pm/
9aca37cb-1629-5c67-1895-
1fdc45c0244e@linaro.org/
[3] https://lore.kernel.org/linux-pm/
af9857f2-578e-de3a-e62b-
6baff7e69fd4@linaro.org/
CC: Daniel Lezcano <daniel.lezcano@linaro.org>
Fixes:
a50c1e35650b ("mlxsw: core: Implement thermal zone")
Fixes:
a421ce088ac8 ("mlxsw: core: Extend cooling device with cooling levels")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20211012174955.472928-1-idosch@idosch.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Arnd Bergmann [Wed, 13 Oct 2021 14:35:49 +0000 (16:35 +0200)]
ethernet: s2io: fix setting mac address during resume
After recent cleanups, gcc started warning about a suspicious
memcpy() call during the s2io_io_resume() function:
In function '__dev_addr_set',
inlined from 'eth_hw_addr_set' at include/linux/etherdevice.h:318:2,
inlined from 's2io_set_mac_addr' at drivers/net/ethernet/neterion/s2io.c:5205:2,
inlined from 's2io_io_resume' at drivers/net/ethernet/neterion/s2io.c:8569:7:
arch/x86/include/asm/string_32.h:182:25: error: '__builtin_memcpy' accessing 6 bytes at offsets 0 and 2 overlaps 4 bytes at offset 2 [-Werror=restrict]
182 | #define memcpy(t, f, n) __builtin_memcpy(t, f, n)
| ^~~~~~~~~~~~~~~~~~~~~~~~~
include/linux/netdevice.h:4648:9: note: in expansion of macro 'memcpy'
4648 | memcpy(dev->dev_addr, addr, len);
| ^~~~~~
What apparently happened is that an old cleanup changed the calling
conventions for s2io_set_mac_addr() from taking an ethernet address
as a character array to taking a struct sockaddr, but one of the
callers was not changed at the same time.
Change it to instead call the low-level do_s2io_prog_unicast() function
that still takes the old argument type.
Fixes:
2fd376884558 ("S2io: Added support set_mac_address driver entry point")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211013143613.2049096-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Dinh Nguyen [Wed, 13 Oct 2021 03:40:56 +0000 (22:40 -0500)]
MAINTAINERS: Update entry for the Stratix10 firmware
Richard Gong is no longer at Intel, so update the MAINTAINER's entry for
the Stratix10 firmware drivers.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 14 Oct 2021 13:53:36 +0000 (09:53 -0400)]
Merge tag 'sound-5.15-rc6' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This contains quite a few device-specific fixes for usual HD- and
USB-audio in addition to a couple of ALSA core fixes (a UAF fix in
sequencer and a fix for a misplaced PCM 32bit compat ioctl).
Nothing really stands out"
* tag 'sound-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Add quirk for VF0770
ALSA: hda: avoid write to STATESTS if controller is in reset
ALSA: hda/realtek: Fix the mic type detection issue for ASUS G551JW
ALSA: pcm: Workaround for a wrong offset in SYNC_PTR compat ioctl
ALSA: hda/realtek: Fix for quirk to enable speaker output on the Lenovo 13s Gen2
ALSA: hda: intel: Allow repeatedly probing on codec configuration errors
ALSA: hda/realtek: Add quirk for TongFang PHxTxX1
ALSA: hda/realtek - ALC236 headset MIC recording issue
ALSA: usb-audio: Enable rate validation for Scarlett devices
ALSA: hda/realtek: Add quirk for Clevo X170KM-G
ALSA: hda/realtek: Complete partial device name to avoid ambiguity
ALSA: hda - Enable headphone mic on Dell Latitude laptops with ALC3254
ALSA: seq: Fix a potential UAF by wrong private_free call order
ALSA: hda/realtek: Enable 4-speaker output for Dell Precision 5560 laptop
ALSA: usb-audio: Fix a missing error check in scarlett gen2 mixer
Jakub Kicinski [Thu, 14 Oct 2021 00:44:32 +0000 (17:44 -0700)]
Merge branch 'fix-two-possible-memory-leak-problems-in-nfc-digital-module'
Ziyang Xuan says:
====================
Fix two possible memory leak problems in NFC digital module.
====================
Link: https://lore.kernel.org/r/cover.1634111083.git.william.xuanziyang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ziyang Xuan [Wed, 13 Oct 2021 07:50:32 +0000 (15:50 +0800)]
NFC: digital: fix possible memory leak in digital_in_send_sdd_req()
'skb' is allocated in digital_in_send_sdd_req(), but not free when
digital_in_send_cmd() failed, which will cause memory leak. Fix it
by freeing 'skb' if digital_in_send_cmd() return failed.
Fixes:
2c66daecc409 ("NFC Digital: Add NFC-A technology support")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ziyang Xuan [Wed, 13 Oct 2021 07:50:12 +0000 (15:50 +0800)]
NFC: digital: fix possible memory leak in digital_tg_listen_mdaa()
'params' is allocated in digital_tg_listen_mdaa(), but not free when
digital_send_cmd() failed, which will cause memory leak. Fix it by
freeing 'params' if digital_send_cmd() return failed.
Fixes:
1c7a4c24fbfd ("NFC Digital: Add target NFC-DEP support")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ziyang Xuan [Wed, 13 Oct 2021 03:49:32 +0000 (11:49 +0800)]
nfc: fix error handling of nfc_proto_register()
When nfc proto id is using, nfc_proto_register() return -EBUSY error
code, but forgot to unregister proto. Fix it by adding proto_unregister()
in the error handling case.
Fixes:
c7fe3b52c128 ("NFC: add NFC socket family")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211013034932.2833737-1-william.xuanziyang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Wed, 13 Oct 2021 00:19:09 +0000 (03:19 +0300)]
Revert "net: procfs: add seq_puts() statement for dev_mcast"
This reverts commit
ec18e8455484370d633a718c6456ddbf6eceef21.
It turns out that there are user space programs which got broken by that
change. One example is the "ifstat" program shipped by Debian:
https://packages.debian.org/source/bullseye/ifstat
which, confusingly enough, seems to not have anything in common with the
much more familiar (at least to me) ifstat program from iproute2:
https://git.kernel.org/pub/scm/network/iproute2/iproute2.git/tree/misc/ifstat.c
root@debian:~# ifstat
ifstat: /proc/net/dev: unsupported format.
This change modified the header (first two lines of text) in
/proc/net/dev so that it looks like this:
root@debian:~# cat /proc/net/dev
Interface| Receive | Transmit
| bytes packets errs drop fifo frame compressed multicast| bytes packets errs drop fifo colls carrier compressed
lo: 97400 1204 0 0 0 0 0 0 97400 1204 0 0 0 0 0 0
bond0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
sit0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
eno2: 5002206 6651 0 0 0 0 0 0
105518642 1465023 0 0 0 0 0 0
swp0: 134531 2448 0 0 0 0 0 0
99599598 1464381 0 0 0 0 0 0
swp1: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
swp2: 4867675 4203 0 0 0 0 0 0 58134 631 0 0 0 0 0 0
sw0p0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
sw0p1: 124739 2448 0 1422 0 0 0 0
93741184 1464369 0 0 0 0 0 0
sw0p2: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
sw2p0: 4850863 4203 0 0 0 0 0 0 54722 619 0 0 0 0 0 0
sw2p1: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
sw2p2: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
sw2p3: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
br0: 10508 212 0 212 0 0 0 212
61369558 958857 0 0 0 0 0 0
whereas before it looked like this:
root@debian:~# cat /proc/net/dev
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed
lo: 13160 164 0 0 0 0 0 0 13160 164 0 0 0 0 0 0
bond0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
sit0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
eno2: 30824 268 0 0 0 0 0 0 3332 37 0 0 0 0 0 0
swp0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
swp1: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
swp2: 30824 268 0 0 0 0 0 0 2428 27 0 0 0 0 0 0
sw0p0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
sw0p1: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
sw0p2: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
sw2p0: 29752 268 0 0 0 0 0 0 1564 17 0 0 0 0 0 0
sw2p1: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
sw2p2: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
sw2p3: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
The reason why the ifstat shipped by Debian (v1.1, with a Debian patch
upgrading it to 1.1-8.1 at the time of writing) is broken is because its
"proc" driver/backend parses the header very literally:
main/drivers.c#L825
if (!data->checked && strncmp(buf, "Inter-|", 7))
goto badproc;
and there's no way in which the header can be changed such that programs
parsing like that would not get broken.
Even if we fix this ancient and very "lightly" maintained program to
parse the text output of /proc/net/dev in a more sensible way, this
story seems bound to repeat again with other programs, and modifying
them all could cause more trouble than it's worth. On the other hand,
the reverted patch had no other reason than an aesthetic one, so
reverting it is the simplest way out.
I don't know what other distributions would be affected; the fact that
Debian doesn't ship the iproute2 version of the program (a different
code base altogether, which uses netlink and not /proc/net/dev) is
surprising in itself.
Fixes:
ec18e8455484 ("net: procfs: add seq_puts() statement for dev_mcast")
Link: https://lore.kernel.org/netdev/20211009163511.vayjvtn3rrteglsu@skbuf/
Cc: Yajun Deng <yajun.deng@linux.dev>
Cc: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20211013001909.3164185-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nanyong Sun [Tue, 12 Oct 2021 12:59:01 +0000 (20:59 +0800)]
net: encx24j600: check error in devm_regmap_init_encx24j600
devm_regmap_init may return error which caused by like out of memory,
this will results in null pointer dereference later when reading
or writing register:
general protection fault in encx24j600_spi_probe
KASAN: null-ptr-deref in range [0x0000000000000090-0x0000000000000097]
CPU: 0 PID: 286 Comm: spi-encx24j600- Not tainted 5.15.0-rc2-00142-g9978db750e31-dirty #11
9c53a778c1306b1b02359f3c2bbedc0222cba652
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
RIP: 0010:regcache_cache_bypass drivers/base/regmap/regcache.c:540
Code: 54 41 89 f4 55 53 48 89 fb 48 83 ec 08 e8 26 94 a8 fe 48 8d bb a0 00 00 00 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 4a 03 00 00 4c 8d ab b0 00 00 00 48 8b ab a0 00
RSP: 0018:
ffffc900010476b8 EFLAGS:
00010207
RAX:
dffffc0000000000 RBX:
fffffffffffffff4 RCX:
0000000000000000
RDX:
0000000000000012 RSI:
ffff888002de0000 RDI:
0000000000000094
RBP:
ffff888013c9a000 R08:
0000000000000000 R09:
fffffbfff3f9cc6a
R10:
ffffc900010476e8 R11:
fffffbfff3f9cc69 R12:
0000000000000001
R13:
000000000000000a R14:
ffff888013c9af54 R15:
ffff888013c9ad08
FS:
00007ffa984ab580(0000) GS:
ffff88801fe00000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
000055a6384136c8 CR3:
000000003bbe6003 CR4:
0000000000770ef0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
PKRU:
55555554
Call Trace:
encx24j600_spi_probe drivers/net/ethernet/microchip/encx24j600.c:459
spi_probe drivers/spi/spi.c:397
really_probe drivers/base/dd.c:517
__driver_probe_device drivers/base/dd.c:751
driver_probe_device drivers/base/dd.c:782
__device_attach_driver drivers/base/dd.c:899
bus_for_each_drv drivers/base/bus.c:427
__device_attach drivers/base/dd.c:971
bus_probe_device drivers/base/bus.c:487
device_add drivers/base/core.c:3364
__spi_add_device drivers/spi/spi.c:599
spi_add_device drivers/spi/spi.c:641
spi_new_device drivers/spi/spi.c:717
new_device_store+0x18c/0x1f1 [spi_stub
4e02719357f1ff33f5a43d00630982840568e85e]
dev_attr_store drivers/base/core.c:2074
sysfs_kf_write fs/sysfs/file.c:139
kernfs_fop_write_iter fs/kernfs/file.c:300
new_sync_write fs/read_write.c:508 (discriminator 4)
vfs_write fs/read_write.c:594
ksys_write fs/read_write.c:648
do_syscall_64 arch/x86/entry/common.c:50
entry_SYSCALL_64_after_hwframe arch/x86/entry/entry_64.S:113
Add error check in devm_regmap_init_encx24j600 to avoid this situation.
Fixes:
04fbfce7a222 ("net: Microchip encx24j600 driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Nanyong Sun <sunnanyong@huawei.com>
Link: https://lore.kernel.org/r/20211012125901.3623144-1-sunnanyong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 13 Oct 2021 20:39:54 +0000 (13:39 -0700)]
Merge tag 'mlx5-fixes-2021-10-12' of git://git./linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2021-10-12
* tag 'mlx5-fixes-2021-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: Fix division by 0 in mlx5e_select_queue for representors
net/mlx5e: Mutually exclude RX-FCS and RX-port-timestamp
net/mlx5e: Switchdev representors are not vlan challenged
net/mlx5e: Fix memory leak in mlx5_core_destroy_cq() error path
net/mlx5e: Allow only complete TXQs partition in MQPRIO channel mode
net/mlx5: Fix cleanup of bridge delayed work
====================
Link: https://lore.kernel.org/r/20211012205323.20123-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vegard Nossum [Tue, 12 Oct 2021 15:25:09 +0000 (17:25 +0200)]
net: korina: select CRC32
Fix the following build/link error by adding a dependency on the CRC32
routines:
ld: drivers/net/ethernet/korina.o: in function `korina_multicast_list':
korina.c:(.text+0x1af): undefined reference to `crc32_le'
Fixes:
ef11291bcd5f9 ("Add support the Korina (IDT RC32434) Ethernet MAC")
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Acked-by: Florian fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211012152509.21771-1-vegard.nossum@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vegard Nossum [Tue, 12 Oct 2021 09:34:46 +0000 (11:34 +0200)]
net: arc: select CRC32
Fix the following build/link error by adding a dependency on the CRC32
routines:
ld: drivers/net/ethernet/arc/emac_main.o: in function `arc_emac_set_rx_mode':
emac_main.c:(.text+0xb11): undefined reference to `crc32_le'
The crc32_le() call comes through the ether_crc_le() call in
arc_emac_set_rx_mode().
[v2: moved the select to ARC_EMAC_CORE; the Makefile is a bit confusing,
but the error comes from emac_main.o, which is part of the arc_emac module,
which in turn is enabled by CONFIG_ARC_EMAC_CORE. Note that arc_emac is
different from emac_arc...]
Fixes:
775dd682e2b0ec ("arc_emac: implement promiscuous mode and multicast filtering")
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Link: https://lore.kernel.org/r/20211012093446.1575-1-vegard.nossum@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Wed, 13 Oct 2021 14:42:07 +0000 (07:42 -0700)]
Merge tag 'modules-for-v5.15-rc6' of git://git./linux/kernel/git/jeyu/linux
Pull modules fix from Jessica Yu:
- Build fix for cfi_init() when CONFIG_MODULE_UNLOAD=n
* tag 'modules-for-v5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
module: fix clang CFI with MODULE_UNLOAD=n
Jakub Kicinski [Wed, 13 Oct 2021 00:35:21 +0000 (17:35 -0700)]
Merge branch 'felix-dsa-driver-fixes'
Vladimir Oltean says:
====================
Felix DSA driver fixes
This is an assorted collection of fixes for issues seen on the NXP
LS1028A switch.
- PTP packet drops due to switch congestion result in catastrophic
damage to the driver's state
- loops are not blocked by STP if using the ocelot-8021q tagger
- driver uses the wrong CPU port when two of them are defined in DT
- module autoloading is broken* with both tagging protocol drivers
(ocelot and ocelot-8021q)
Changes in v2:
- Stop printing that we aren't going to take TX timestamps if we don't
have TX timestamping anyway, and we are just carrying PTP frames for a
cascaded DSA switch.
- Shorten the deferred xmit kthread name so that it fits the 16
character limit (TASK_COMM_LEN)
====================
Link: https://lore.kernel.org/r/20211012114044.2526146-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Tue, 12 Oct 2021 11:40:44 +0000 (14:40 +0300)]
net: dsa: felix: break at first CPU port during init and teardown
The NXP LS1028A switch has two Ethernet ports towards the CPU, but only
one of them is capable of acting as an NPI port at a time (inject and
extract packets using DSA tags).
However, using the alternative ocelot-8021q tagging protocol, it should
be possible to use both CPU ports symmetrically, but for that we need to
mark both ports in the device tree as DSA masters.
In the process of doing that, it can be seen that traffic to/from the
network stack gets broken, and this is because the Felix driver iterates
through all DSA CPU ports and configures them as NPI ports. But since
there can only be a single NPI port, we effectively end up in a
situation where DSA thinks the default CPU port is the first one, but
the hardware port configured to be an NPI is the last one.
I would like to treat this as a bug, because if the updated device trees
are going to start circulating, it would be really good for existing
kernels to support them, too.
Fixes:
adb3dccf090b ("net: dsa: felix: convert to the new .change_tag_protocol DSA API")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Tue, 12 Oct 2021 11:40:43 +0000 (14:40 +0300)]
net: dsa: tag_ocelot_8021q: fix inability to inject STP BPDUs into BLOCKING ports
When setting up a bridge with stp_state 1, topology changes are not
detected and loops are not blocked. This is because the standard way of
transmitting a packet, based on VLAN IDs redirected by VCAP IS2 to the
right egress port, does not override the port STP state (in the case of
Ocelot switches, that's really the PGID_SRC masks).
To force a packet to be injected into a port that's BLOCKING, we must
send it as a control packet, which means in the case of this tagger to
send it using the manual register injection method. We already do this
for PTP frames, extend the logic to apply to any link-local MAC DA.
Fixes:
7c83a7c539ab ("net: dsa: add a second tagger for Ocelot switches based on tag_8021q")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Tue, 12 Oct 2021 11:40:42 +0000 (14:40 +0300)]
net: dsa: felix: purge skb from TX timestamping queue if it cannot be sent
At present, when a PTP packet which requires TX timestamping gets
dropped under congestion by the switch, things go downhill very fast.
The driver keeps a clone of that skb in a queue of packets awaiting TX
timestamp interrupts, but interrupts will never be raised for the
dropped packets.
Moreover, matching timestamped packets to timestamps is done by a 2-bit
timestamp ID, and this can wrap around and we can match on the wrong skb.
Since with the default NPI-based tagging protocol, we get no notification
about packet drops, the best we can do is eventually recover from the
drop of a PTP frame: its skb will be dead memory until another skb which
was assigned the same timestamp ID happens to find it.
However, with the ocelot-8021q tagger which injects packets using the
manual register interface, it appears that we can check for more
information, such as:
- whether the input queue has reached the high watermark or not
- whether the injection group's FIFO can accept additional data or not
so we know that a PTP frame is likely to get dropped before actually
sending it, and drop it ourselves (because DSA uses NETIF_F_LLTX, so it
can't return NETDEV_TX_BUSY to ask the qdisc to requeue the packet).
But when we do that, we can also remove the skb from the timestamping
queue, because there surely won't be any timestamp that matches it.
Fixes:
0a6f17c6ae21 ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Tue, 12 Oct 2021 11:40:41 +0000 (14:40 +0300)]
net: dsa: tag_ocelot_8021q: break circular dependency with ocelot switch lib
Michael reported that when using the "ocelot-8021q" tagging protocol,
the switch driver module must be manually loaded before the tagging
protocol can be loaded/is available.
This appears to be the same problem described here:
https://lore.kernel.org/netdev/
20210908220834.d7gmtnwrorhharna@skbuf/
where due to the fact that DSA tagging protocols make use of symbols
exported by the switch drivers, circular dependencies appear and this
breaks module autoloading.
The ocelot_8021q driver needs the ocelot_can_inject() and
ocelot_port_inject_frame() functions from the switch library. Previously
the wrong approach was taken to solve that dependency: shims were
provided for the case where the ocelot switch library was compiled out,
but that turns out to be insufficient, because the dependency when the
switch lib _is_ compiled is problematic too.
We cannot declare ocelot_can_inject() and ocelot_port_inject_frame() as
static inline functions, because these access I/O functions like
__ocelot_write_ix() which is called by ocelot_write_rix(). Making those
static inline basically means exposing the whole guts of the ocelot
switch library, not ideal...
We already have one tagging protocol driver which calls into the switch
driver during xmit but not using any exported symbol: sja1105_defer_xmit.
We can do the same thing here: create a kthread worker and one work item
per skb, and let the switch driver itself do the register accesses to
send the skb, and then consume it.
Fixes:
0a6f17c6ae21 ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping")
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Tue, 12 Oct 2021 11:40:40 +0000 (14:40 +0300)]
net: dsa: tag_ocelot: break circular dependency with ocelot switch lib driver
As explained here:
https://lore.kernel.org/netdev/
20210908220834.d7gmtnwrorhharna@skbuf/
DSA tagging protocol drivers cannot depend on symbols exported by switch
drivers, because this creates a circular dependency that breaks module
autoloading.
The tag_ocelot.c file depends on the ocelot_ptp_rew_op() function
exported by the common ocelot switch lib. This function looks at
OCELOT_SKB_CB(skb) and computes how to populate the REW_OP field of the
DSA tag, for PTP timestamping (the command: one-step/two-step, and the
TX timestamp identifier).
None of that requires deep insight into the driver, it is quite
stateless, as it only depends upon the skb->cb. So let's make it a
static inline function and put it in include/linux/dsa/ocelot.h, a
file that despite its name is used by the ocelot switch driver for
populating the injection header too - since commit
40d3f295b5fe ("net:
mscc: ocelot: use common tag parsing code with DSA").
With that function declared as static inline, its body is expanded
inside each call site, so the dependency is broken and the DSA tagger
can be built without the switch library, upon which the felix driver
depends.
Fixes:
39e5308b3250 ("net: mscc: ocelot: support PTP Sync one-step timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Tue, 12 Oct 2021 11:40:39 +0000 (14:40 +0300)]
net: mscc: ocelot: cross-check the sequence id from the timestamp FIFO with the skb PTP header
The sad reality is that when a PTP frame with a TX timestamping request
is transmitted, it isn't guaranteed that it will make it all the way to
the wire (due to congestion inside the switch), and that a timestamp
will be taken by the hardware and placed in the timestamp FIFO where an
IRQ will be raised for it.
The implication is that if enough PTP frames are silently dropped by the
hardware such that the timestamp ID has rolled over, it is possible to
match a timestamp to an old skb.
Furthermore, nobody will match on the real skb corresponding to this
timestamp, since we stupidly matched on a previous one that was stale in
the queue, and stopped there.
So PTP timestamping will be broken and there will be no way to recover.
It looks like the hardware parses the sequenceID from the PTP header,
and also provides that metadata for each timestamp. The driver currently
ignores this, but it shouldn't.
As an extra resiliency measure, do the following:
- check whether the PTP sequenceID also matches between the skb and the
timestamp, treat the skb as stale otherwise and free it
- if we see a stale skb, don't stop there and try to match an skb one
more time, chances are there's one more skb in the queue with the same
timestamp ID, otherwise we wouldn't have ever found the stale one (it
is by timestamp ID that we matched it).
While this does not prevent PTP packet drops, it at least prevents
the catastrophic consequences of incorrect timestamp matching.
Since we already call ptp_classify_raw in the TX path, save the result
in the skb->cb of the clone, and just use that result in the interrupt
code path.
Fixes:
4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Tue, 12 Oct 2021 11:40:38 +0000 (14:40 +0300)]
net: mscc: ocelot: deny TX timestamping of non-PTP packets
It appears that Ocelot switches cannot timestamp non-PTP frames,
I tested this using the isochron program at:
https://github.com/vladimiroltean/tsn-scripts
with the result that the driver increments the ocelot_port->ts_id
counter as expected, puts it in the REW_OP, but the hardware seems to
not timestamp these packets at all, since no IRQ is emitted.
Therefore check whether we are sending PTP frames, and refuse to
populate REW_OP otherwise.
Fixes:
4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Tue, 12 Oct 2021 11:40:37 +0000 (14:40 +0300)]
net: mscc: ocelot: warn when a PTP IRQ is raised for an unknown skb
When skb_match is NULL, it means we received a PTP IRQ for a timestamp
ID that the kernel has no idea about, since there is no skb in the
timestamping queue with that timestamp ID.
This is a grave error and not something to just "continue" over.
So print a big warning in case this happens.
Also, move the check above ocelot_get_hwtimestamp(), there is no point
in reading the full 64-bit current PTP time if we're not going to do
anything with it anyway for this skb.
Fixes:
4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Tue, 12 Oct 2021 11:40:36 +0000 (14:40 +0300)]
net: mscc: ocelot: avoid overflowing the PTP timestamp FIFO
PTP packets with 2-step TX timestamp requests are matched to packets
based on the egress port number and a 6-bit timestamp identifier.
All PTP timestamps are held in a common FIFO that is 128 entry deep.
This patch ensures that back-to-back timestamping requests cannot exceed
the hardware FIFO capacity. If that happens, simply send the packets
without requesting a TX timestamp to be taken (in the case of felix,
since the DSA API has a void return code in ds->ops->port_txtstamp) or
drop them (in the case of ocelot).
I've moved the ts_id_lock from a per-port basis to a per-switch basis,
because we need separate accounting for both numbers of PTP frames in
flight. And since we need locking to inc/dec the per-switch counter,
that also offers protection for the per-port counter and hence there is
no reason to have a per-port counter anymore.
Fixes:
4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Tue, 12 Oct 2021 11:40:35 +0000 (14:40 +0300)]
net: mscc: ocelot: make use of all 63 PTP timestamp identifiers
At present, there is a problem when user space bombards a port with PTP
event frames which have TX timestamping requests (or when a tc-taprio
offload is installed on a port, which delays the TX timestamps by a
significant amount of time). The driver will happily roll over the 2-bit
timestamp ID and this will cause incorrect matches between an skb and
the TX timestamp collected from the FIFO.
The Ocelot switches have a 6-bit PTP timestamp identifier, and the value
63 is reserved, so that leaves identifiers 0-62 to be used.
The timestamp identifiers are selected by the REW_OP packet field, and
are actually shared between CPU-injected frames and frames which match a
VCAP IS2 rule that modifies the REW_OP. The hardware supports
partitioning between the two uses of the REW_OP field through the
PTP_ID_LOW and PTP_ID_HIGH registers, and by default reserves the PTP
IDs 0-3 for CPU-injected traffic and the rest for VCAP IS2.
The driver does not use VCAP IS2 to set REW_OP for 2-step timestamping,
and it also writes 0xffffffff to both PTP_ID_HIGH and PTP_ID_LOW in
ocelot_init_timestamp() which makes all timestamp identifiers available
to CPU injection.
Therefore, we can make use of all 63 timestamp identifiers, which should
allow more timestampable packets to be in flight on each port. This is
only part of the solution, more issues will be addressed in future changes.
Fixes:
4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 13 Oct 2021 00:33:39 +0000 (17:33 -0700)]
Merge branch 'fix-circular-dependency-between-sja1105-and-tag_sja1105'
Vladimir Oltean says:
====================
Fix circular dependency between sja1105 and tag_sja1105
As discussed here:
https://lore.kernel.org/netdev/
20210908220834.d7gmtnwrorhharna@skbuf/
DSA tagging protocols cannot use symbols exported by switch drivers.
Eliminate the two instances of that from tag_sja1105, and that allows us
to have a working setup with modules again.
====================
Re-applying to net, this was mistakenly applied to net-next,
see first Link.
Link: https://lore.kernel.org/r/20211012114044.2526146-1-vladimir.oltean@nxp.com/
Link: https://lore.kernel.org/r/20210922143726.2431036-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Wed, 22 Sep 2021 14:37:26 +0000 (17:37 +0300)]
net: dsa: sja1105: break dependency between dsa_port_is_sja1105 and switch driver
It's nice to be able to test a tagging protocol with dsa_loop, but not
at the cost of losing the ability of building the tagging protocol and
switch driver as modules, because as things stand, there is a circular
dependency between the two. Tagging protocol drivers cannot depend on
switch drivers, that is a hard fact.
The reasoning behind the blamed patch was that accessing dp->priv should
first make sure that the structure behind that pointer is what we really
think it is.
Currently the "sja1105" and "sja1110" tagging protocols only operate
with the sja1105 switch driver, just like any other tagging protocol and
switch combination. The only way to mix and match them is by modifying
the code, and this applies to dsa_loop as well (by default that uses
DSA_TAG_PROTO_NONE). So while in principle there is an issue, in
practice there isn't one.
Until we extend dsa_loop to allow user space configuration, treat the
problem as a non-issue and just say that DSA ports found by tag_sja1105
are always sja1105 ports, which is in fact true. But keep the
dsa_port_is_sja1105 function so that it's easy to patch it during
testing, and rely on dead code elimination.
Fixes:
994d2cbb08ca ("net: dsa: tag_sja1105: be dsa_loop-safe")
Link: https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Wed, 22 Sep 2021 14:37:25 +0000 (17:37 +0300)]
net: dsa: move sja1110_process_meta_tstamp inside the tagging protocol driver
The problem is that DSA tagging protocols really must not depend on the
switch driver, because this creates a circular dependency at insmod
time, and the switch driver will effectively not load when the tagging
protocol driver is missing.
The code was structured in the way it was for a reason, though. The DSA
driver-facing API for PTP timestamping relies on the assumption that
two-step TX timestamps are provided by the hardware in an out-of-band
manner, typically by raising an interrupt and making that timestamp
available inside some sort of FIFO which is to be accessed over
SPI/MDIO/etc.
So the API puts .port_txtstamp into dsa_switch_ops, because it is
expected that the switch driver needs to save some state (like put the
skb into a queue until its TX timestamp arrives).
On SJA1110, TX timestamps are provided by the switch as Ethernet
packets, so this makes them be received and processed by the tagging
protocol driver. This in itself is great, because the timestamps are
full 64-bit and do not require reconstruction, and since Ethernet is the
fastest I/O method available to/from the switch, PTP timestamps arrive
very quickly, no matter how bottlenecked the SPI connection is, because
SPI interaction is not needed at all.
DSA's code structure and strict isolation between the tagging protocol
driver and the switch driver break the natural code organization.
When the tagging protocol driver receives a packet which is classified
as a metadata packet containing timestamps, it passes those timestamps
one by one to the switch driver, which then proceeds to compare them
based on the recorded timestamp ID that was generated in .port_txtstamp.
The communication between the tagging protocol and the switch driver is
done through a method exported by the switch driver, sja1110_process_meta_tstamp.
To satisfy build requirements, we force a dependency to build the
tagging protocol driver as a module when the switch driver is a module.
However, as explained in the first paragraph, that causes the circular
dependency.
To solve this, move the skb queue from struct sja1105_private :: struct
sja1105_ptp_data to struct sja1105_private :: struct sja1105_tagger_data.
The latter is a data structure for which hacks have already been put
into place to be able to create persistent storage per switch that is
accessible from the tagging protocol driver (see sja1105_setup_ports).
With the skb queue directly accessible from the tagging protocol driver,
we can now move sja1110_process_meta_tstamp into the tagging driver
itself, and avoid exporting a symbol.
Fixes:
566b18c8b752 ("net: dsa: sja1105: implement TX timestamping for SJA1110")
Link: https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alvin Šipraga [Tue, 12 Oct 2021 11:27:31 +0000 (13:27 +0200)]
net: dsa: fix spurious error message when unoffloaded port leaves bridge
Flip the sign of a return value check, thereby suppressing the following
spurious error:
port 2 failed to notify DSA_NOTIFIER_BRIDGE_LEAVE: -EOPNOTSUPP
... which is emitted when removing an unoffloaded DSA switch port from a
bridge.
Fixes:
d371b7c92d19 ("net: dsa: Unset vlan_filtering when ports leave the bridge")
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211012112730.3429157-1-alvin@pqrs.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Baowen Zheng [Tue, 12 Oct 2021 12:48:50 +0000 (14:48 +0200)]
nfp: flow_offload: move flow_indr_dev_register from app init to app start
In commit
74fc4f828769 ("net: Fix offloading indirect devices dependency
on qdisc order creation"), it adds a process to trigger the callback to
setup the bo callback when the driver regists a callback.
In our current implement, we are not ready to run the callback when nfp
call the function flow_indr_dev_register, then there will be error
message as:
kernel: Oops: 0000 [#1] SMP PTI
kernel: CPU: 0 PID: 14119 Comm: kworker/0:0 Tainted: G
kernel: Workqueue: events work_for_cpu_fn
kernel: RIP: 0010:nfp_flower_indr_setup_tc_cb+0x258/0x410
kernel: RSP: 0018:
ffffbc1e02c57bf8 EFLAGS:
00010286
kernel: RAX:
0000000000000000 RBX:
ffff9c761fabc000 RCX:
0000000000000001
kernel: RDX:
0000000000000001 RSI:
fffffffffffffff0 RDI:
ffffffffc0be9ef1
kernel: RBP:
ffffbc1e02c57c58 R08:
ffffffffc08f33aa R09:
ffff9c6db7478800
kernel: R10:
0000009c003f6e00 R11:
ffffbc1e02800000 R12:
ffffbc1e000d9000
kernel: R13:
ffffbc1e000db428 R14:
ffff9c6db7478800 R15:
ffff9c761e884e80
kernel: CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
kernel: CR2:
fffffffffffffff0 CR3:
00000009e260a004 CR4:
00000000007706f0
kernel: DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
kernel: DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
kernel: PKRU:
55555554
kernel: Call Trace:
kernel: ? flow_indr_dev_register+0xab/0x210
kernel: ? __cond_resched+0x15/0x30
kernel: ? kmem_cache_alloc_trace+0x44/0x4b0
kernel: ? nfp_flower_setup_tc+0x1d0/0x1d0 [nfp]
kernel: flow_indr_dev_register+0x158/0x210
kernel: ? tcf_block_unbind+0xe0/0xe0
kernel: nfp_flower_init+0x40b/0x650 [nfp]
kernel: nfp_net_pci_probe+0x25f/0x960 [nfp]
kernel: ? nfp_rtsym_read_le+0x76/0x130 [nfp]
kernel: nfp_pci_probe+0x6a9/0x820 [nfp]
kernel: local_pci_probe+0x45/0x80
So we need to call flow_indr_dev_register in app start process instead of
init stage.
Fixes:
74fc4f828769 ("net: Fix offloading indirect devices dependency on qdisc order creation")
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Link: https://lore.kernel.org/r/20211012124850.13025-1-louis.peens@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Maxim Mikityanskiy [Mon, 11 Oct 2021 15:39:35 +0000 (18:39 +0300)]
net/mlx5e: Fix division by 0 in mlx5e_select_queue for representors
Commit
846d6da1fcdb ("net/mlx5e: Fix division by 0 in
mlx5e_select_queue") makes mlx5e_build_nic_params assign a non-zero
initial value to priv->num_tc_x_num_ch, so that mlx5e_select_queue
doesn't fail with division by 0 if called before the first activation of
channels. However, the initialization flow of representors doesn't call
mlx5e_build_nic_params, so this bug can still happen with representors.
This commit fixes the bug by adding the missing assignment to
mlx5e_build_rep_params.
Fixes:
846d6da1fcdb ("net/mlx5e: Fix division by 0 in mlx5e_select_queue")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Aya Levin [Sun, 26 Sep 2021 14:55:41 +0000 (17:55 +0300)]
net/mlx5e: Mutually exclude RX-FCS and RX-port-timestamp
Due to current HW arch limitations, RX-FCS (scattering FCS frame field
to software) and RX-port-timestamp (improved timestamp accuracy on the
receive side) can't work together.
RX-port-timestamp is not controlled by the user and it is enabled by
default when supported by the HW/FW.
This patch sets RX-port-timestamp opposite to RX-FCS configuration.
Fixes:
102722fc6832 ("net/mlx5e: Add support for RXFCS feature flag")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Saeed Mahameed [Tue, 5 Oct 2021 04:20:25 +0000 (21:20 -0700)]
net/mlx5e: Switchdev representors are not vlan challenged
Before this patch, mlx5 representors advertised the
NETIF_F_VLAN_CHALLENGED bit, this could lead to missing features when
using reps with vxlan/bridge and maybe other virtual interfaces,
when such interfaces inherit this bit and block vlan usage in their
topology.
Example:
$ip link add dev bridge type bridge
# add representor interface to the bridge
$ip link set dev pf0hpf master
$ip link add link bridge name vlan10 type vlan id 10 protocol 802.1q
Error: 8021q: VLANs not supported on device.
Reps are perfectly capable of handling vlan traffic, although they don't
implement vlan_{add,kill}_vid ndos, hence, remove
NETIF_F_VLAN_CHALLENGED advertisement.
Fixes:
cb67b832921c ("net/mlx5e: Introduce SRIOV VF representors")
Reported-by: Roopa Prabhu <roopa@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Valentine Fatiev [Sun, 15 Aug 2021 14:43:19 +0000 (17:43 +0300)]
net/mlx5e: Fix memory leak in mlx5_core_destroy_cq() error path
Prior to this patch in case mlx5_core_destroy_cq() failed it returns
without completing all destroy operations and that leads to memory leak.
Instead, complete the destroy flow before return error.
Also move mlx5_debug_cq_remove() to the beginning of mlx5_core_destroy_cq()
to be symmetrical with mlx5_core_create_cq().
kmemleak complains on:
unreferenced object 0xc000000038625100 (size 64):
comm "ethtool", pid 28301, jiffies
4298062946 (age 785.380s)
hex dump (first 32 bytes):
60 01 48 94 00 00 00 c0 b8 05 34 c3 00 00 00 c0 `.H.......4.....
02 00 00 00 00 00 00 00 00 db 7d c1 00 00 00 c0 ..........}.....
backtrace:
[<
000000009e8643cb>] add_res_tree+0xd0/0x270 [mlx5_core]
[<
00000000e7cb8e6c>] mlx5_debug_cq_add+0x5c/0xc0 [mlx5_core]
[<
000000002a12918f>] mlx5_core_create_cq+0x1d0/0x2d0 [mlx5_core]
[<
00000000cef0a696>] mlx5e_create_cq+0x210/0x3f0 [mlx5_core]
[<
000000009c642c26>] mlx5e_open_cq+0xb4/0x130 [mlx5_core]
[<
0000000058dfa578>] mlx5e_ptp_open+0x7f4/0xe10 [mlx5_core]
[<
0000000081839561>] mlx5e_open_channels+0x9cc/0x13e0 [mlx5_core]
[<
0000000009cf05d4>] mlx5e_switch_priv_channels+0xa4/0x230
[mlx5_core]
[<
0000000042bbedd8>] mlx5e_safe_switch_params+0x14c/0x300
[mlx5_core]
[<
0000000004bc9db8>] set_pflag_tx_port_ts+0x9c/0x160 [mlx5_core]
[<
00000000a0553443>] mlx5e_set_priv_flags+0xd0/0x1b0 [mlx5_core]
[<
00000000a8f3d84b>] ethnl_set_privflags+0x234/0x2d0
[<
00000000fd27f27c>] genl_family_rcv_msg_doit+0x108/0x1d0
[<
00000000f495e2bb>] genl_family_rcv_msg+0xe4/0x1f0
[<
00000000646c5c2c>] genl_rcv_msg+0x78/0x120
[<
00000000d53e384e>] netlink_rcv_skb+0x74/0x1a0
Fixes:
e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Valentine Fatiev <valentinef@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Tariq Toukan [Mon, 4 Oct 2021 12:04:25 +0000 (15:04 +0300)]
net/mlx5e: Allow only complete TXQs partition in MQPRIO channel mode
Do not allow configurations of MQPRIO channel mode that do not
fully define and utilize the channels txqs.
Fixes:
ec60c4581bd9 ("net/mlx5e: Support MQPRIO channel mode")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Shay Drory [Mon, 13 Sep 2021 12:48:11 +0000 (15:48 +0300)]
net/mlx5: Fix cleanup of bridge delayed work
Currently, bridge cleanup is calling to cancel_delayed_work(). When this
function is finished, there is a chance that the delayed work is still
running. Also, the delayed work is queueing itself.
As a result, we might execute the delayed work after the bridge cleanup
have finished and hit a null-ptr oops[1].
Fix it by using cancel_delayed_work_sync(), which is waiting until the
work is done and will cancel the queue work.
[1]
[ 8202.143043 ] BUG: kernel NULL pointer dereference, address:
0000000000000000
[ 8202.144438 ] #PF: supervisor write access in kernel mode
[ 8202.145476 ] #PF: error_code(0x0002) - not-present page
[ 8202.146520 ] PGD 0 P4D 0
[ 8202.147126 ] Oops: 0002 [#1] SMP NOPTI
[ 8202.147899 ] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.14.0-rc6_for_upstream_min_debug_2021_08_25_16_06 #1
[ 8202.149741 ] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
[ 8202.151908 ] RIP: 0010:_raw_spin_lock+0xc/0x20
[ 8202.156234 ] RSP: 0018:
ffff88846f885ea0 EFLAGS:
00010046
[ 8202.157289 ] RAX:
0000000000000000 RBX:
ffff88846f880000 RCX:
0000000000000000
[ 8202.158731 ] RDX:
0000000000000001 RSI:
ffff8881004000c8 RDI:
0000000000000000
[ 8202.160177 ] RBP:
ffff8881fe684978 R08:
ffff888100140000 R09:
ffffffff824455b8
[ 8202.161569 ] R10:
0000000000000000 R11:
0000000000000000 R12:
0000000000000001
[ 8202.163004 ] R13:
0000000000000012 R14:
0000000000000200 R15:
ffff88812992d000
[ 8202.164018 ] FS:
0000000000000000(0000) GS:
ffff88846f880000(0000) knlGS:
0000000000000000
[ 8202.164960 ] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 8202.165634 ] CR2:
0000000000000000 CR3:
0000000108cac004 CR4:
0000000000370ea0
[ 8202.166450 ] DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
[ 8202.167807 ] DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
[ 8202.168852 ] Call Trace:
[ 8202.169421 ] <IRQ>
[ 8202.169792 ] __queue_work+0xf2/0x3d0
[ 8202.170481 ] ? queue_work_node+0x40/0x40
[ 8202.171270 ] call_timer_fn+0x2b/0x100
[ 8202.171932 ] __run_timers.part.0+0x152/0x220
[ 8202.172717 ] ? __hrtimer_run_queues+0x171/0x290
[ 8202.173526 ] ? kvm_clock_get_cycles+0xd/0x10
[ 8202.174232 ] ? ktime_get+0x35/0x90
[ 8202.174943 ] run_timer_softirq+0x26/0x50
[ 8202.175745 ] __do_softirq+0xc7/0x271
[ 8202.176373 ] irq_exit_rcu+0x93/0xb0
[ 8202.176983 ] sysvec_apic_timer_interrupt+0x72/0x90
[ 8202.177755 ] </IRQ>
[ 8202.178245 ] asm_sysvec_apic_timer_interrupt+0x12/0x20
Fixes:
c636a0f0f3f0 ("net/mlx5: Bridge, dynamic entry ageing")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Jonas Hahnfeld [Tue, 12 Oct 2021 20:09:07 +0000 (22:09 +0200)]
ALSA: usb-audio: Add quirk for VF0770
The device advertises 8 formats, but only a rate of 48kHz is honored
by the hardware and 24 bits give chopped audio, so only report the
one working combination. This fixes out-of-the-box audio experience
with PipeWire which otherwise attempts to choose S24_3LE (while
PulseAudio defaulted to S16_LE).
Signed-off-by: Jonas Hahnfeld <hahnjo@hahnjo.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211012200906.3492-1-hahnjo@hahnjo.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Linus Torvalds [Tue, 12 Oct 2021 18:16:38 +0000 (11:16 -0700)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Fix CMA gigantic page order for 16K/64K page sizes
- Fix section mismatch error in drivers/acpi/arm64/gtdt.c
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
acpi/arm64: fix next_platform_timer() section mismatch error
arm64/hugetlb: fix CMA gigantic page order for non-4K PAGE_SIZE
Linus Torvalds [Tue, 12 Oct 2021 18:11:39 +0000 (11:11 -0700)]
Merge tag 'platform-drivers-x86-v5.15-3' of git://git./linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
"A second (small) set of pdx86 bug-fixes and new hardware ids for 5.15"
* tag 'platform-drivers-x86-v5.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: int1092: Fix non sequential device mode handling
platform/x86: intel_skl_int3472: Correct null check
platform/x86: gigabyte-wmi: add support for B550 AORUS ELITE AX V2
platform/x86: amd-pmc: Add alternative acpi id for PMC controller
platform/x86: intel_scu_ipc: Update timeout value in comment
platform/x86: intel_scu_ipc: Increase virtual timeout to 10s
platform/x86: intel_scu_ipc: Fix busy loop expiry time
platform/x86: dell: Make DELL_WMI_PRIVACY depend on DELL_WMI
platform/mellanox: mlxreg-io: Fix read access of n-bytes size attributes
platform/mellanox: mlxreg-io: Fix argument base in kstrtou32() call
Jackie Liu [Mon, 23 Aug 2021 09:25:26 +0000 (17:25 +0800)]
acpi/arm64: fix next_platform_timer() section mismatch error
Fix modpost Section mismatch error in next_platform_timer().
[...]
WARNING: modpost: vmlinux.o(.text.unlikely+0x26e60): Section mismatch in reference from the function next_platform_timer() to the variable .init.data:acpi_gtdt_desc
The function next_platform_timer() references
the variable __initdata acpi_gtdt_desc.
This is often because next_platform_timer lacks a __initdata
annotation or the annotation of acpi_gtdt_desc is wrong.
WARNING: modpost: vmlinux.o(.text.unlikely+0x26e64): Section mismatch in reference from the function next_platform_timer() to the variable .init.data:acpi_gtdt_desc
The function next_platform_timer() references
the variable __initdata acpi_gtdt_desc.
This is often because next_platform_timer lacks a __initdata
annotation or the annotation of acpi_gtdt_desc is wrong.
ERROR: modpost: Section mismatches detected.
Set CONFIG_SECTION_MISMATCH_WARN_ONLY=y to allow them.
make[1]: *** [scripts/Makefile.modpost:59: vmlinux.symvers] Error 1
make[1]: *** Deleting file 'vmlinux.symvers'
make: *** [Makefile:1176: vmlinux] Error 2
[...]
Fixes:
a712c3ed9b8a ("acpi/arm64: Add memory-mapped timer support in GTDT driver")
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Acked-by: Hanjun Guo <guohanjun@huawei.com>
Link: https://lore.kernel.org/r/20210823092526.2407526-1-liu.yun@linux.dev
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Kai Vehmanen [Tue, 12 Oct 2021 14:29:35 +0000 (17:29 +0300)]
ALSA: hda: avoid write to STATESTS if controller is in reset
The snd_hdac_bus_reset_link() contains logic to clear STATESTS register
before performing controller reset. This code dates back to an old
bugfix in commit
e8a7f136f5ed ("[ALSA] hda-intel - Improve HD-audio
codec probing robustness"). Originally the code was added to
azx_reset().
The code was moved around in commit
a41d122449be ("ALSA: hda - Embed bus
into controller object") and ended up to snd_hdac_bus_reset_link() and
called primarily via snd_hdac_bus_init_chip().
The logic to clear STATESTS is correct when snd_hdac_bus_init_chip() is
called when controller is not in reset. In this case, STATESTS can be
cleared. This can be useful e.g. when forcing a controller reset to retry
codec probe. A normal non-power-on reset will not clear the bits.
However, this old logic is problematic when controller is already in
reset. The HDA specification states that controller must be taken out of
reset before writing to registers other than GCTL.CRST (1.0a spec,
3.3.7). The write to STATESTS in snd_hdac_bus_reset_link() will be lost
if the controller is already in reset per the HDA specification mentioned.
This has been harmless on older hardware. On newer generation of Intel
PCIe based HDA controllers, if configured to report issues, this write
will emit an unsupported request error. If ACPI Platform Error Interface
(APEI) is enabled in kernel, this will end up to kernel log.
Fix the code in snd_hdac_bus_reset_link() to only clear the STATESTS if
the function is called when controller is not in reset. Otherwise
clearing the bits is not possible and should be skipped.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20211012142935.3731820-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Hui Wang [Tue, 12 Oct 2021 11:47:48 +0000 (19:47 +0800)]
ALSA: hda/realtek: Fix the mic type detection issue for ASUS G551JW
We need to define the codec pin 0x1b to be the mic, but somehow
the mic doesn't support hot plugging detection, and Windows also has
this issue, so we set it to phantom headset-mic.
Also the determine_headset_type() often returns the omtp type by a
mistake when we plug a ctia headset, this makes the mic can't record
sound at all. Because most of the headset are ctia type nowadays and
some machines have the fixed ctia type audio jack, it is possible this
machine has the fixed ctia jack too. Here we set this mic jack to
fixed ctia type, this could avoid the mic type detection mistake and
make the ctia headset work stable.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214537
Reported-and-tested-by: msd <msd.mmq@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20211012114748.5238-1-hui.wang@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Jacob Keller [Mon, 11 Oct 2021 20:48:06 +0000 (13:48 -0700)]
ice: fix locking for Tx timestamp tracking flush
Commit
4dd0d5c33c3e ("ice: add lock around Tx timestamp tracker flush")
added a lock around the Tx timestamp tracker flow which is used to
cleanup any left over SKBs and prepare for device removal.
This lock is problematic because it is being held around a call to
ice_clear_phy_tstamp. The clear function takes a mutex to send a PHY
write command to firmware. This could lead to a deadlock if the mutex
actually sleeps, and causes the following warning on a kernel with
preemption debugging enabled:
[ 715.419426] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:573
[ 715.427900] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 3100, name: rmmod
[ 715.435652] INFO: lockdep is turned off.
[ 715.439591] Preemption disabled at:
[ 715.439594] [<
0000000000000000>] 0x0
[ 715.446678] CPU: 52 PID: 3100 Comm: rmmod Tainted: G W OE 5.15.0-rc4+ #42
bdd7ec3018e725f159ca0d372ce8c2c0e784891c
[ 715.458058] Hardware name: Intel Corporation S2600STQ/S2600STQ, BIOS SE5C620.86B.02.01.0010.
010620200716 01/06/2020
[ 715.468483] Call Trace:
[ 715.470940] dump_stack_lvl+0x6a/0x9a
[ 715.474613] ___might_sleep.cold+0x224/0x26a
[ 715.478895] __mutex_lock+0xb3/0x1440
[ 715.482569] ? stack_depot_save+0x378/0x500
[ 715.486763] ? ice_sq_send_cmd+0x78/0x14c0 [ice
9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.494979] ? kfree+0xc1/0x520
[ 715.498128] ? mutex_lock_io_nested+0x12a0/0x12a0
[ 715.502837] ? kasan_set_free_info+0x20/0x30
[ 715.507110] ? __kasan_slab_free+0x10b/0x140
[ 715.511385] ? slab_free_freelist_hook+0xc7/0x220
[ 715.516092] ? kfree+0xc1/0x520
[ 715.519235] ? ice_deinit_lag+0x16c/0x220 [ice
9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.527359] ? ice_remove+0x1cf/0x6a0 [ice
9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.535133] ? pci_device_remove+0xab/0x1d0
[ 715.539318] ? __device_release_driver+0x35b/0x690
[ 715.544110] ? driver_detach+0x214/0x2f0
[ 715.548035] ? bus_remove_driver+0x11d/0x2f0
[ 715.552309] ? pci_unregister_driver+0x26/0x250
[ 715.556840] ? ice_module_exit+0xc/0x2f [ice
9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.564799] ? __do_sys_delete_module.constprop.0+0x2d8/0x4e0
[ 715.570554] ? do_syscall_64+0x3b/0x90
[ 715.574303] ? entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 715.579529] ? start_flush_work+0x542/0x8f0
[ 715.583719] ? ice_sq_send_cmd+0x78/0x14c0 [ice
9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.591923] ice_sq_send_cmd+0x78/0x14c0 [ice
9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.599960] ? wait_for_completion_io+0x250/0x250
[ 715.604662] ? lock_acquire+0x196/0x200
[ 715.608504] ? do_raw_spin_trylock+0xa5/0x160
[ 715.612864] ice_sbq_rw_reg+0x1e6/0x2f0 [ice
9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.620813] ? ice_reset+0x130/0x130 [ice
9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.628497] ? __debug_check_no_obj_freed+0x1e8/0x3c0
[ 715.633550] ? trace_hardirqs_on+0x1c/0x130
[ 715.637748] ice_write_phy_reg_e810+0x70/0xf0 [ice
9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.646220] ? do_raw_spin_trylock+0xa5/0x160
[ 715.650581] ? ice_ptp_release+0x910/0x910 [ice
9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.658797] ? ice_ptp_release+0x255/0x910 [ice
9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.667013] ice_clear_phy_tstamp+0x2c/0x110 [ice
9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.675403] ice_ptp_release+0x408/0x910 [ice
9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.683440] ice_remove+0x560/0x6a0 [ice
9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.691037] ? _raw_spin_unlock_irqrestore+0x46/0x73
[ 715.696005] pci_device_remove+0xab/0x1d0
[ 715.700018] __device_release_driver+0x35b/0x690
[ 715.704637] driver_detach+0x214/0x2f0
[ 715.708389] bus_remove_driver+0x11d/0x2f0
[ 715.712489] pci_unregister_driver+0x26/0x250
[ 715.716857] ice_module_exit+0xc/0x2f [ice
9a7e1ec00971c89ecd3fe0d4dc7da2b3786a421d]
[ 715.724637] __do_sys_delete_module.constprop.0+0x2d8/0x4e0
[ 715.730210] ? free_module+0x6d0/0x6d0
[ 715.733963] ? task_work_run+0xe1/0x170
[ 715.737803] ? exit_to_user_mode_loop+0x17f/0x1d0
[ 715.742509] ? rcu_read_lock_sched_held+0x12/0x80
[ 715.747215] ? trace_hardirqs_on+0x1c/0x130
[ 715.751401] do_syscall_64+0x3b/0x90
[ 715.754981] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 715.760033] RIP: 0033:0x7f4dfe59000b
[ 715.763612] Code: 73 01 c3 48 8b 0d 6d 1e 0c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa b8 b0 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 3d 1e 0c 00 f7 d8 64 89 01 48
[ 715.782357] RSP: 002b:
00007ffe8c891708 EFLAGS:
00000206 ORIG_RAX:
00000000000000b0
[ 715.789923] RAX:
ffffffffffffffda RBX:
00005558a20468b0 RCX:
00007f4dfe59000b
[ 715.797054] RDX:
000000000000000a RSI:
0000000000000800 RDI:
00005558a2046918
[ 715.804189] RBP:
0000000000000000 R08:
0000000000000000 R09:
0000000000000000
[ 715.811319] R10:
00007f4dfe603ac0 R11:
0000000000000206 R12:
00007ffe8c891940
[ 715.818455] R13:
00007ffe8c8920a3 R14:
00005558a20462a0 R15:
00005558a20468b0
Notice that this is the only case where we use the lock in this way. In
the cleanup kthread and work kthread the lock is only taken around the
bit accesses. This was done intentionally to avoid this kind of issue.
The way the lock is used, we only protect ordering of bit sets vs bit
clears. The Tx writers in the hot path don't need to be protected
against the entire kthread loop. The Tx queues threads only need to
ensure that they do not re-use an index that is currently in use. The
cleanup loop does not need to block all new set bits, since it will
re-queue itself if new timestamps are present.
Fix the tracker flow so that it uses the same flow as the standard
cleanup thread. In addition, ensure the in_use bitmap actually gets
cleared properly.
This fixes the warning and also avoids the potential deadlock that might
have occurred otherwise.
Fixes:
4dd0d5c33c3e ("ice: add lock around Tx timestamp tracker flush")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 12 Oct 2021 10:49:50 +0000 (11:49 +0100)]
Merge branch 'ioam-fixes'
Justin Iurman says:
====================
Correct the IOAM behavior for undefined trace type bits
(@Jakub @David: there will be a conflict for #2 when merging net->net-next, due
to commit [1]. The conflict is only 5-10 lines for #2 (#1 should be fine) inside
the file tools/testing/selftests/net/ioam6.sh, so quite short though possibly
ugly. Sorry for that, I didn't expect to post this one... Had I known, I'd have
made the opposite.)
Modify both the input and output behaviors regarding the trace type when one of
the undefined bits is set. The goal is to keep the interoperability when new
fields (aka new bits inside the range 12-21) will be defined.
The draft [2] says the following:
---------------------------------------------------------------
"Bit 12-21 Undefined. These values are available for future
assignment in the IOAM Trace-Type Registry (Section 8.2).
Every future node data field corresponding to one of
these bits MUST be 4-octets long. An IOAM encapsulating
node MUST set the value of each undefined bit to 0. If
an IOAM transit node receives a packet with one or more
of these bits set to 1, it MUST either:
1. Add corresponding node data filled with the reserved
value 0xFFFFFFFF, after the node data fields for the
IOAM-Trace-Type bits defined above, such that the
total node data added by this node in units of
4-octets is equal to NodeLen, or
2. Not add any node data fields to the packet, even for
the IOAM-Trace-Type bits defined above."
---------------------------------------------------------------
The output behavior has been modified to respect the fact that "an IOAM encap
node MUST set the value of each undefined bit to 0" (i.e., undefined bits can't
be set anymore).
As for the input behavior, current implementation is based on the second choice
(i.e., "not add any data fields to the packet [...]"). With this solution, any
interoperability is lost (i.e., if a new bit is defined, then an "old" kernel
implementation wouldn't fill IOAM data when such new bit is set inside the trace
type).
The input behavior is therefore relaxed and these undefined bits are now allowed
to be set. It is only possible thanks to the sentence "every future node data
field corresponding to one of these bits MUST be 4-octets long". Indeed, the
default empty value (the one for 4-octet fields) is inserted whenever an
undefined bit is set.
[1]
cfbe9b002109621bf9a282a4a24f9415ef14b57b
[2] https://datatracker.ietf.org/doc/html/draft-ietf-ippm-ioam-data#section-5.4.1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Justin Iurman [Mon, 11 Oct 2021 18:04:12 +0000 (20:04 +0200)]
selftests: net: modify IOAM tests for undef bits
The output behavior for undefined bits is now directly tested inside the bash
script. Trying to set an undefined bit should be refused.
The input behavior for undefined bits has been removed due to the fact that we
would need another sender allowed to set undefined bits.
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Justin Iurman [Mon, 11 Oct 2021 18:04:11 +0000 (20:04 +0200)]
ipv6: ioam: move the check for undefined bits
The check for undefined bits in the trace type is moved from the input side to
the output side, while the input side is relaxed and now inserts default empty
values when an undefined bit is set.
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arun Ramadoss [Mon, 11 Oct 2021 15:48:08 +0000 (21:18 +0530)]
net: dsa: microchip: Added the condition for scheduling ksz_mib_read_work
When the ksz module is installed and removed using rmmod, kernel crashes
with null pointer dereferrence error. During rmmod, ksz_switch_remove
function tries to cancel the mib_read_workqueue using
cancel_delayed_work_sync routine and unregister switch from dsa.
During dsa_unregister_switch it calls ksz_mac_link_down, which in turn
reschedules the workqueue since mib_interval is non-zero.
Due to which queue executed after mib_interval and it tries to access
dp->slave. But the slave is unregistered in the ksz_switch_remove
function. Hence kernel crashes.
To avoid this crash, before canceling the workqueue, resetted the
mib_interval to 0.
v1 -> v2:
-Removed the if condition in ksz_mib_read_work
Fixes:
469b390e1ba3 ("net: dsa: microchip: use delayed_work instead of timer + work")
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vegard Nossum [Mon, 11 Oct 2021 15:22:49 +0000 (17:22 +0200)]
r8152: select CRC32 and CRYPTO/CRYPTO_HASH/CRYPTO_SHA256
Fix the following build/link errors by adding a dependency on
CRYPTO, CRYPTO_HASH, CRYPTO_SHA256 and CRC32:
ld: drivers/net/usb/r8152.o: in function `rtl8152_fw_verify_checksum':
r8152.c:(.text+0x2b2a): undefined reference to `crypto_alloc_shash'
ld: r8152.c:(.text+0x2bed): undefined reference to `crypto_shash_digest'
ld: r8152.c:(.text+0x2c50): undefined reference to `crypto_destroy_tfm'
ld: drivers/net/usb/r8152.o: in function `_rtl8152_set_rx_mode':
r8152.c:(.text+0xdcb0): undefined reference to `crc32_le'
Fixes:
9370f2d05a2a1 ("r8152: support request_firmware for RTL8153")
Fixes:
ac718b69301c7 ("net/usb: new driver for RTL8152")
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maarten Zanders [Mon, 11 Oct 2021 14:27:20 +0000 (16:27 +0200)]
net: dsa: mv88e6xxx: don't use PHY_DETECT on internal PHY's
mv88e6xxx_port_ppu_updates() interpretes data in the PORT_STS
register incorrectly for internal ports (ie no PPU). In these
cases, the PHY_DETECT bit indicates link status. This results
in forcing the MAC state whenever the PHY link goes down which
is not intended. As a side effect, LED's configured to show
link status stay lit even though the physical link is down.
Add a check in mac_link_down and mac_link_up to see if it
concerns an external port and only then, look at PPU status.
Fixes:
5d5b231da7ac (net: dsa: mv88e6xxx: use PHY_DETECT in mac_link_up/mac_link_down)
Reported-by: Maarten Zanders <m.zanders@televic.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Maarten Zanders <maarten.zanders@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wan Jiabing [Mon, 11 Oct 2021 02:27:41 +0000 (10:27 +0800)]
net: mscc: ocelot: Fix dumplicated argument in ocelot
Fix the following coccicheck warning:
drivers/net/ethernet/mscc/ocelot.c:474:duplicated argument to & or |
drivers/net/ethernet/mscc/ocelot.c:476:duplicated argument to & or |
drivers/net/ethernet/mscc/ocelot_net.c:1627:duplicated argument
to & or |
These DEV_CLOCK_CFG_MAC_TX_RST are duplicate here.
Here should be DEV_CLOCK_CFG_MAC_RX_RST.
Fixes:
e6e12df625f2 ("net: mscc: ocelot: convert to phylink")
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Boyd [Fri, 8 Oct 2021 21:59:45 +0000 (14:59 -0700)]
af_unix: Rename UNIX-DGRAM to UNIX to maintain backwards compatability
Then name of this protocol changed in commit
94531cfcbe79 ("af_unix: Add
unix_stream_proto for sockmap") because that commit added stream support
to the af_unix protocol. Renaming the existing protocol makes a ChromeOS
protocol test[1] fail now that the name has changed in
/proc/net/protocols from "UNIX" to "UNIX-DGRAM".
Let's put the name back to how it was while keeping the stream protocol
as "UNIX-STREAM" so that the procfs interface doesn't change. This fixes
the test and maintains backwards compatibility in proc.
Cc: Jiang Wang <jiang.wang@bytedance.com>
Cc: Andrii Nakryiko <andrii@kernel.org>
Cc: Cong Wang <cong.wang@bytedance.com>
Cc: Jakub Sitnicki <jakub@cloudflare.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Dmitry Osipenko <digetx@gmail.com>
Link: https://source.chromium.org/chromiumos/chromiumos/codesearch/+/main:src/platform/tast-tests/src/chromiumos/tast/local/bundles/cros/network/supported_protocols.go;l=50;drc=e8b1c3f94cb40a054f4aa1ef1aff61e75dc38f18
Fixes:
94531cfcbe79 ("af_unix: Add unix_stream_proto for sockmap")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 12 Oct 2021 00:25:08 +0000 (17:25 -0700)]
Merge tag 'linux-kselftest-kunit-fixes-5.15-rc6' of git://git./linux/kernel/git/shuah/linux-kselftest
Pull Kunit fixes from Shuah Khan:
- Fixes to address the structleak plugin causing the stack frame size
to grow immensely when used with KUnit. Fixes include adding a new
makefile to disable structleak and using it from KUnit iio, device
property, thunderbolt, and bitfield tests to disable it.
- KUnit framework reference count leak in kfree_at_end
- KUnit tool fix to resolve conflict between --json and --raw_output
and generate correct test output in either case.
- kernel-doc warnings due to mismatched arg names
* tag 'linux-kselftest-kunit-fixes-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
kunit: fix kernel-doc warnings due to mismatched arg names
bitfield: build kunit tests without structleak plugin
thunderbolt: build kunit tests without structleak plugin
device property: build kunit tests without structleak plugin
iio/test-format: build kunit tests without structleak plugin
gcc-plugins/structleak: add makefile var for disabling structleak
kunit: fix reference count leak in kfree_at_end
kunit: tool: better handling of quasi-bool args (--json, --raw_output)
Linus Torvalds [Tue, 12 Oct 2021 00:16:41 +0000 (17:16 -0700)]
Merge branch 'for-5.15-fixes' of git://git./linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
"All documentation / comment updates"
* 'for-5.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroupv2, docs: fix misinformation in "device controller" section
cgroup/cpuset: Change references of cpuset_mutex to cpuset_rwsem
docs/cgroup: remove some duplicate words
Linus Torvalds [Mon, 11 Oct 2021 23:59:49 +0000 (16:59 -0700)]
Merge branch 'for-5.15-fixes' of git://git./linux/kernel/git/tj/wq
Pull workqueue fixes from Tejun Heo:
"One patch to add a missing __printf annotation and the other to enable
deferred printing for debug dumps to avoid deadlocks when triggered
from some contexts (e.g. console drivers)"
* 'for-5.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: fix state-dump console deadlock
workqueue: annotate alloc_workqueue() as printf
Linus Torvalds [Mon, 11 Oct 2021 23:48:19 +0000 (16:48 -0700)]
Merge tag 'for-5.15-rc5-tag' of git://git./linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"A few more error handling fixes, stemming from code inspection, error
injection or fuzzing"
* tag 'for-5.15-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix abort logic in btrfs_replace_file_extents
btrfs: check for error when looking up inode during dir entry replay
btrfs: unify lookup return value when dir entry is missing
btrfs: deal with errors when adding inode reference during log replay
btrfs: deal with errors when replaying dir entry during log replay
btrfs: deal with errors when checking if a dir entry exists during log replay
btrfs: update refs for any root except tree log roots
btrfs: unlock newly allocated extent buffer after error
Mike Kravetz [Tue, 5 Oct 2021 20:25:29 +0000 (13:25 -0700)]
arm64/hugetlb: fix CMA gigantic page order for non-4K PAGE_SIZE
For non-4K PAGE_SIZE configs, the largest gigantic huge page size is
CONT_PMD_SHIFT order. On arm64 with 64K PAGE_SIZE, the gigantic page is
16G. Therefore, one should be able to specify 'hugetlb_cma=16G' on the
kernel command line so that one gigantic page can be allocated from CMA.
However, when adding such an option the following message is produced:
hugetlb_cma: cma area should be at least
8796093022208 MiB
This is because the calculation for non-4K gigantic page order is
incorrect in the arm64 specific routine arm64_hugetlb_cma_reserve().
Fixes:
abb7962adc80 ("arm64/hugetlb: Reserve CMA areas for gigantic pages on 16K and 64K configs")
Cc: <stable@vger.kernel.org> # 5.9.x
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Link: https://lore.kernel.org/r/20211005202529.213812-1-mike.kravetz@oracle.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Johan Hovold [Wed, 6 Oct 2021 11:58:52 +0000 (13:58 +0200)]
workqueue: fix state-dump console deadlock
Console drivers often queue work while holding locks also taken in their
console write paths, something which can lead to deadlocks on SMP when
dumping workqueue state (e.g. sysrq-t or on suspend failures).
For serial console drivers this could look like:
CPU0 CPU1
---- ----
show_workqueue_state();
lock(&pool->lock); <IRQ>
lock(&port->lock);
schedule_work();
lock(&pool->lock);
printk();
lock(console_owner);
lock(&port->lock);
where workqueues are, for example, used to push data to the line
discipline, process break signals and handle modem-status changes. Line
disciplines and serdev drivers can also queue work on write-wakeup
notifications, etc.
Reworking every console driver to avoid queuing work while holding locks
also taken in their write paths would complicate drivers and is neither
desirable or feasible.
Instead use the deferred-printk mechanism to avoid printing while
holding pool locks when dumping workqueue state.
Note that there are a few WARN_ON() assertions in the workqueue code
which could potentially also trigger a deadlock. Hopefully the ongoing
printk rework will provide a general solution for this eventually.
This was originally reported after a lockdep splat when executing
sysrq-t with the imx serial driver.
Fixes:
3494fc30846d ("workqueue: dump workqueues on sysrq-t")
Cc: stable@vger.kernel.org # 4.0
Reported-by: Fabio Estevam <festevam@denx.de>
Tested-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Takashi Iwai [Sun, 10 Oct 2021 07:55:46 +0000 (09:55 +0200)]
ALSA: pcm: Workaround for a wrong offset in SYNC_PTR compat ioctl
Michael Forney reported an incorrect padding type that was defined in
the commit
80fe7430c708 ("ALSA: add new 32-bit layout for
snd_pcm_mmap_status/control") for PCM control mmap data.
His analysis is correct, and this caused the misplacements of PCM
control data on 32bit arch and 32bit compat mode.
The bug is that the __pad2 definition in __snd_pcm_mmap_control64
struct was wrongly with __pad_before_uframe, which should have been
__pad_after_uframe instead. This struct is used in SYNC_PTR ioctl and
control mmap. Basically this bug leads to two problems:
- The offset of avail_min field becomes wrong, it's placed right after
appl_ptr without padding on little-endian
- When appl_ptr and avail_min are read as 64bit values in kernel side,
the values become either zero or corrupted (mixed up)
One good news is that, because both user-space and kernel
misunderstand the wrong offset, at least, 32bit application running on
32bit kernel works as is. Also, 64bit applications are unaffected
because the padding size is zero. The remaining problem is the 32bit
compat mode; as mentioned in the above, avail_min is placed right
after appl_ptr on little-endian archs, 64bit kernel reads bogus values
for appl_ptr updates, which may lead to streaming bugs like jumping,
XRUN or whatever unexpected.
(However, we haven't heard any serious bug reports due to this over
years, so practically seen, it's fairly safe to assume that the impact
by this bug is limited.)
Ideally speaking, we should correct the wrong mmap status control
definition. But this would cause again incompatibility with the
existing binaries, and fixing it (e.g. by renumbering ioctls) would be
really messy.
So, as of this patch, we only correct the behavior of 32bit compat
mode and keep the rest as is. Namely, the SYNC_PTR ioctl is now
handled differently in compat mode to read/write the 32bit values at
the right offsets. The control mmap of 32bit apps on 64bit kernels
has been already disabled (which is likely rather an overlook, but
this worked fine at this time :), so covering SYNC_PTR ioctl should
suffice as a fallback.
Fixes:
80fe7430c708 ("ALSA: add new 32-bit layout for snd_pcm_mmap_status/control")
Reported-by: Michael Forney <mforney@mforney.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Cc: <stable@vger.kernel.org>
Cc: Rich Felker <dalias@libc.org>
Link: https://lore.kernel.org/r/29QBMJU8DE71E.2YZSH8IHT5HMH@mforney.org
Link: https://lore.kernel.org/r/20211010075546.23220-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Shravan S [Wed, 6 Oct 2021 07:35:25 +0000 (13:05 +0530)]
platform/x86: int1092: Fix non sequential device mode handling
SAR information from BIOS may come in non sequential pattern.
To overcome the issue, a check is made to extract the right SAR
information using the device mode which is currently being used.
Remove .owner field if calls are used which set it automatically.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Shravan S <s.shravan@intel.com>
Link: https://lore.kernel.org/r/20211006073525.1332925-1-s.shravan@intel.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Daniel Scally [Fri, 8 Oct 2021 22:46:08 +0000 (23:46 +0100)]
platform/x86: intel_skl_int3472: Correct null check
The int3472-discrete driver can enter an error path after initialising
int3472->clock.ena_gpio, but before it has registered the clock. This will
cause a NULL pointer dereference, because clkdev_drop() is not null aware.
Instead of guarding the call to skl_int3472_unregister_clock() by checking
for .ena_gpio, check specifically for the presence of the clk_lookup, which
will guarantee clkdev_create() has already been called.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=214453
Fixes:
7540599a5ef1 ("platform/x86: intel_skl_int3472: Provide skl_int3472_unregister_clock()")
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Link: https://lore.kernel.org/r/20211008224608.415949-1-djrscally@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Zephaniah E. Loss-Cutler-Hull [Tue, 5 Oct 2021 04:48:55 +0000 (21:48 -0700)]
platform/x86: gigabyte-wmi: add support for B550 AORUS ELITE AX V2
This works just fine on my system.
Signed-off-by: Zephaniah E. Loss-Cutler-Hull <zephaniah@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211005044855.1429724-1-zephaniah@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Sachi King [Sat, 2 Oct 2021 04:18:39 +0000 (14:18 +1000)]
platform/x86: amd-pmc: Add alternative acpi id for PMC controller
The Surface Laptop 4 AMD has used the AMD0005 to identify this
controller instead of using the appropriate ACPI ID AMDI0005. Include
AMD0005 in the acpi id list.
Link: https://github.com/linux-surface/acpidumps/tree/master/surface_laptop_4_amd
Link: https://gist.github.com/nakato/2a1a7df1a45fe680d7a08c583e1bf863
Cc: <stable@vger.kernel.org> # 5.14+
Signed-off-by: Sachi King <nakato@nakato.io>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20211002041840.2058647-1-nakato@nakato.io
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Prashant Malani [Tue, 28 Sep 2021 10:19:34 +0000 (03:19 -0700)]
platform/x86: intel_scu_ipc: Update timeout value in comment
The comment decribing the IPC timeout hadn't been updated when the
actual timeout was changed from 3 to 5 seconds in
commit
a7d53dbbc70a ("platform/x86: intel_scu_ipc: Increase virtual
timeout from 3 to 5 seconds") .
Since the value is anyway updated to 10s now, take this opportunity to
update the value in the comment too.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Cc: Benson Leung <bleung@chromium.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20210928101932.2543937-4-pmalani@chromium.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Prashant Malani [Tue, 28 Sep 2021 10:19:32 +0000 (03:19 -0700)]
platform/x86: intel_scu_ipc: Increase virtual timeout to 10s
Commit
a7d53dbbc70a ("platform/x86: intel_scu_ipc: Increase virtual
timeout from 3 to 5 seconds") states that the recommended timeout range
is 5-10 seconds. Adjust the timeout value to the higher of those i.e 10
seconds, to account for situations where the 5 seconds is insufficient
for disconnect command success.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Cc: Benson Leung <bleung@chromium.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20210928101932.2543937-3-pmalani@chromium.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Prashant Malani [Tue, 28 Sep 2021 10:19:30 +0000 (03:19 -0700)]
platform/x86: intel_scu_ipc: Fix busy loop expiry time
The macro IPC_TIMEOUT is already in jiffies (it is also used like that
elsewhere in the file when calling wait_for_completion_timeout()). Don’t
convert it using helper functions for the purposes of calculating the
busy loop expiry time.
Fixes:
e7b7ab3847c9 (“platform/x86: intel_scu_ipc: Sleeping is fine when polling”)
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Cc: Benson Leung <bleung@chromium.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20210928101932.2543937-2-pmalani@chromium.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Mon, 11 Oct 2021 13:23:38 +0000 (15:23 +0200)]
platform/x86: dell: Make DELL_WMI_PRIVACY depend on DELL_WMI
DELL_WMI_PRIVACY is a feature toggle for the main dell-wmi driver,
so it must depend on the Kconfig option which enables the main
dell-wmi driver.
Fixes:
8af9fa37b8a3 ("platform/x86: dell-privacy: Add support for Dell hardware privacy")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211011132338.407571-1-hdegoede@redhat.com
Vadim Pasternak [Mon, 27 Sep 2021 14:22:14 +0000 (17:22 +0300)]
platform/mellanox: mlxreg-io: Fix read access of n-bytes size attributes
Fix shift argument for function rol32(). It should be provided in bits,
while was provided in bytes.
Fixes:
86148190a7db ("platform/mellanox: mlxreg-io: Add support for complex attributes")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20210927142214.2613929-3-vadimp@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Vadim Pasternak [Mon, 27 Sep 2021 14:22:13 +0000 (17:22 +0300)]
platform/mellanox: mlxreg-io: Fix argument base in kstrtou32() call
Change kstrtou32() argument 'base' to be zero instead of 'len'.
It works by chance for setting one bit value, but it is not supposed to
work in case value passed to mlxreg_io_attr_store() is greater than 1.
It works for example, for:
echo 1 > /sys/devices/platform/mlxplat/mlxreg-io/hwmon/.../jtag_enable
But it will fail for:
echo n > /sys/devices/platform/mlxplat/mlxreg-io/hwmon/.../jtag_enable,
where n > 1.
The flow for input buffer conversion is as below:
_kstrtoull(const char *s, unsigned int base, unsigned long long *res)
calls:
rv = _parse_integer(s, base, &_res);
For the second case, where n > 1:
- _parse_integer() converts 's' to 'val'.
For n=2, 'len' is set to 2 (string buffer is 0x32 0x0a), for n=3
'len' is set to 3 (string buffer 0x33 0x0a), etcetera.
- 'base' is equal or greater then '2' (length of input buffer).
As a result, _parse_integer() exits with result zero (rv):
rv = 0;
while (1) {
...
if (val >= base)-> (2 >= 2)
break;
...
rv++;
...
}
And _kstrtoull() in their turn will fail:
if (rv == 0)
return -EINVAL;
Fixes:
5ec4a8ace06c ("platform/mellanox: Introduce support for Mellanox register access driver")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20210927142214.2613929-2-vadimp@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cameron Berkenpas [Sun, 10 Oct 2021 22:54:11 +0000 (15:54 -0700)]
ALSA: hda/realtek: Fix for quirk to enable speaker output on the Lenovo 13s Gen2
The previous patch's HDA verb initialization for the Lenovo 13s
sequence was slightly off. This updated verb sequence has been tested
and confirmed working.
Fixes:
ad7cc2d41b7a ("ALSA: hda/realtek: Quirks to enable speaker output for Lenovo Legion 7i 15IMHG05, Yoga 7i 14ITL5/15ITL5, and 13s Gen2 laptops.")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=208555
Cc: <stable@vger.kernel.org>
Signed-off-by: Cameron Berkenpas <cam@neo-zeon.de>
Link: https://lore.kernel.org/r/20211010225410.23423-1-cam@neo-zeon.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Linus Torvalds [Mon, 11 Oct 2021 00:01:59 +0000 (17:01 -0700)]
Linux 5.15-rc5
Linus Torvalds [Sun, 10 Oct 2021 17:12:42 +0000 (10:12 -0700)]
Merge tag 'powerpc-5.15-3' of git://git./linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"A bit of a big batch, partly because I didn't send any last week, and
also just because the BPF fixes happened to land this week.
Summary:
- Fix a regression hit by the IPR SCSI driver, introduced by the
recent addition of MSI domains on pseries.
- A big series including 8 BPF fixes, some with potential security
impact and the rest various code generation issues.
- Fix our program check assembler entry path, which was accidentally
jumping into a gas macro and generating strange stack frames, which
could confuse find_bug().
- A couple of fixes, and related changes, to fix corner cases in our
machine check handling.
- Fix our DMA IOMMU ops, which were not always returning the optimal
DMA mask, leading to at least one device falling back to 32-bit DMA
when it shouldn't.
- A fix for KUAP handling on 32-bit Book3S.
- Fix crashes seen when kdumping on some pseries systems.
Thanks to Naveen N. Rao, Nicholas Piggin, Alexey Kardashevskiy, Cédric
Le Goater, Christophe Leroy, Mahesh Salgaonkar, Abdul Haleem,
Christoph Hellwig, Johan Almbladh, Stan Johnson"
* tag 'powerpc-5.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
pseries/eeh: Fix the kdump kernel crash during eeh_pseries_init
powerpc/32s: Fix kuap_kernel_restore()
powerpc/pseries/msi: Add an empty irq_write_msi_msg() handler
powerpc/64s: Fix unrecoverable MCE calling async handler from NMI
powerpc/64/interrupt: Reconcile soft-mask state in NMI and fix false BUG
powerpc/64: warn if local irqs are enabled in NMI or hardirq context
powerpc/traps: do not enable irqs in _exception
powerpc/64s: fix program check interrupt emergency stack path
powerpc/bpf ppc32: Fix BPF_SUB when imm == 0x80000000
powerpc/bpf ppc32: Do not emit zero extend instruction for 64-bit BPF_END
powerpc/bpf ppc32: Fix JMP32_JSET_K
powerpc/bpf ppc32: Fix ALU32 BPF_ARSH operation
powerpc/bpf: Emit stf barrier instruction sequences for BPF_NOSPEC
powerpc/security: Add a helper to query stf_barrier type
powerpc/bpf: Fix BPF_SUB when imm == 0x80000000
powerpc/bpf: Fix BPF_MOD when imm == 1
powerpc/bpf: Validate branch ranges
powerpc/lib: Add helper to check if offset is within conditional branch range
powerpc/iommu: Report the correct most efficient DMA mask for PCI devices
Linus Torvalds [Sun, 10 Oct 2021 17:05:39 +0000 (10:05 -0700)]
Merge tag 'objtool_urgent_for_v5.15_rc5' of git://git./linux/kernel/git/tip/tip
Pull objtool fixes from Borislav Petkov:
- Remove an extra section.len member in favour of section.sh_size
- Align .altinstructions section creation with the kernel's by creating
them with entry size of 0
- Fix objtool to convert a reloc symbol to a section offset and not to
not warn about not knowing how
* tag 'objtool_urgent_for_v5.15_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Remove redundant 'len' field from struct section
objtool: Make .altinstructions section entry size consistent
objtool: Remove reloc symbol type checks in get_alt_entry()
Linus Torvalds [Sun, 10 Oct 2021 17:00:51 +0000 (10:00 -0700)]
Merge tag 'x86_urgent_for_v5.15_rc5' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- A FPU fix to properly handle invalid MXCSR values: 32-bit masks them
out due to historical reasons and 64-bit kernels reject them
- A fix to clear X86_FEATURE_SMAP when support for is not
config-enabled
- Three fixes correcting misspelled Kconfig symbols used in code
- Two resctrl object cleanup fixes
- Yet another attempt at fixing the neverending saga of botched x86
timers, this time because some incredibly smart hardware decides to
turn off the HPET timer in a low power state - who cares if the OS is
relying on it...
- Check the full return value range of an SEV VMGEXIT call to determine
whether it returned an error
* tag 'x86_urgent_for_v5.15_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/fpu: Restore the masking out of reserved MXCSR bits
x86/Kconfig: Correct reference to MWINCHIP3D
x86/platform/olpc: Correct ifdef symbol to intended CONFIG_OLPC_XO15_SCI
x86/entry: Clear X86_FEATURE_SMAP when CONFIG_X86_SMAP=n
x86/entry: Correct reference to intended CONFIG_64_BIT
x86/resctrl: Fix kfree() of the wrong type in domain_add_cpu()
x86/resctrl: Free the ctrlval arrays when domain_setup_mon_state() fails
x86/hpet: Use another crystalball to evaluate HPET usability
x86/sev: Return an error on a returned non-zero SW_EXITINFO1[31:0]
Linus Torvalds [Sat, 9 Oct 2021 22:03:48 +0000 (15:03 -0700)]
Merge branch 'i2c/for-current-fixed' of git://git./linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Three driver bugfixes and one leak fix for the core"
* 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: mlxcpld: Modify register setting for 400KHz frequency
i2c: mlxcpld: Fix criteria for frequency setting
i2c: mediatek: Add OFFSET_EXT_CONF setting back
i2c: acpi: fix resource leak in reconfiguration device addition
Linus Torvalds [Sat, 9 Oct 2021 21:57:26 +0000 (14:57 -0700)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Five fixes, all in drivers.
The big change is the UFS task management rework, with lpfc next and
the rest being fairly minor and obvious fixes"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: iscsi: Fix iscsi_task use after free
scsi: lpfc: Fix memory overwrite during FC-GS I/O abort handling
scsi: elx: efct: Delete stray unlock statement
scsi: ufs: core: Fix task management completion
scsi: acornscsi: Remove scsi_cmd_to_tag() reference
Linus Torvalds [Sat, 9 Oct 2021 21:51:59 +0000 (14:51 -0700)]
Merge tag 'block-5.15-2021-10-09' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Two small fixes for this release:
- Add missing QUEUE_FLAG_HCTX_ACTIVE in the debugfs handling
(Johannes)
- Fix double free / UAF issue in __alloc_disk_node (Tetsuo)"
* tag 'block-5.15-2021-10-09' of git://git.kernel.dk/linux-block:
block: decode QUEUE_FLAG_HCTX_ACTIVE in debugfs output
block: genhd: fix double kfree() in __alloc_disk_node()
projects / platform / kernel / linux-rpi.git / log