Linus Torvalds [Fri, 27 Nov 2015 21:12:42 +0000 (13:12 -0800)]
Merge tag 'pm+acpi-4.4-rc3' of git://git./linux/kernel/git/rafael/linux-pm
Pull more power management and ACPI fixes from Rafael Wysocki:
"These fix one recent regression (cpufreq core), fix up two features
added recently (ACPI CPPC support, SCPI support in the arm_big_little
cpufreq driver) and fix three older bugs in the intel_pstate driver.
Specifics:
- Fix a recent regression in the cpufreq core causing it to fail to
clean up sysfs directories properly on cpufreq driver removal
(Viresh Kumar).
- Fix a build problem in the SCPI support code recently added to the
arm_big_little cpufreq driver (Punit Agrawal).
- Fix up the recently added CPPC cpufreq frontend to process the CPU
coordination information provided by the platform firmware
correctly (Ashwin Chaugule).
- Fix the intel_pstate driver to behave as intended when switched
over to the "performance" mode via sysfs if hardware-driven P-state
selection (HWP) is enabled (Alexandra Yates).
- Fix two rounding errors in the intel_pstate driver that sometimes
cause it to use lower P-states than requested (Prarit Bhargava)"
* tag 'pm+acpi-4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
intel_pstate: Fix "performance" mode behavior with HWP enabled
cpufreq: SCPI: Depend on SCPI clk driver
cpufreq: intel_pstate: Fix limits->max_perf rounding error
cpufreq: intel_pstate: Fix limits->max_policy_pct rounding error
cpufreq: Always remove sysfs cpuX/cpufreq link on ->remove_dev()
cpufreq: CPPC: Initialize and check CPUFreq CPU co-ord type correctly
Linus Torvalds [Fri, 27 Nov 2015 19:59:02 +0000 (11:59 -0800)]
Merge tag 'sound-4.4-rc3' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are no big surprises but just all small fixes, mostly
device-specific quirks for HD-audio and USB-audio:
- Fix for detection of FireWire DICE Loud devices
- Intel Broxton HDMI/DP PCI IDs and relevant quirks
- Noise fixes: Dell XPS13 2015 model, Dell Latitude E6440, Gigabyte
Z170X mobo
- Fix the headphone mixer assignment on HP laptops for PulseAudio
- USB-MIDI fixes for Medeli DD305 and CH345
- Apply fixup for Acer Aspire One Cloudbook 14"
* tag 'sound-4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix noise on Gigabyte Z170X mobo
ALSA: hda - Fix headphone noise after Dell XPS 13 resume back from S3
ALSA: hda - Apply HP headphone fixups more generically
ALSA: hda - Add fixup for Acer Aspire One Cloudbook 14
ALSA: hda - apply SKL display power request/release patch to BXT
ALSA: hda - add PCI IDs for Intel Broxton
ALSA: usb-audio: work around CH345 input SysEx corruption
ALSA: usb-audio: prevent CH345 multiport output SysEx corruption
ALSA: usb-audio: add packet size quirk for the Medeli DD305
ALSA: dice: fix detection of Loud devices
ALSA: hda - Fix noise on Dell Latitude E6440
Linus Torvalds [Fri, 27 Nov 2015 19:09:59 +0000 (11:09 -0800)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Build fix when !CONFIG_UID16 (the patch is touching generic files but
it only affects arm64 builds; submitted by Arnd Bergmann)
- EFI fixes to deal with early_memremap() returning NULL and correctly
mapping run-time regions
- Fix CPUID register extraction of unsigned fields (not to be
sign-extended)
- ASID allocator fix to deal with long-running tasks over multiple
generation roll-overs
- Revert support for marking page ranges as contiguous PTEs (it leads
to TLB conflicts and requires additional non-trivial kernel changes)
- Proper early_alloc() failure check
- Disable KASan for 48-bit VA and 16KB page configuration (the pgd is
larger than the KASan shadow memory)
- Update the fault_info table (original descriptions based on early
engineering spec)
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: efi: fix initcall return values
arm64: efi: deal with NULL return value of early_memremap()
arm64: debug: Treat the BRPs/WRPs as unsigned
arm64: cpufeature: Track unsigned fields
arm64: cpufeature: Add helpers for extracting unsigned values
Revert "arm64: Mark kernel page ranges contiguous"
arm64: mm: keep reserved ASIDs in sync with mm after multiple rollovers
arm64: KASAN depends on !(ARM64_16K_PAGES && ARM64_VA_BITS_48)
arm64: efi: correctly map runtime regions
arm64: mm: fix fault_info table xFSC decoding
arm64: fix building without CONFIG_UID16
arm64: early_alloc: Fix check for allocation failure
Linus Torvalds [Fri, 27 Nov 2015 19:05:50 +0000 (11:05 -0800)]
Merge tag 'nios2-v4.4-rc3' of git://git./linux/kernel/git/lftan/nios2
Pull nios2 fix from Ley Foon Tan:
"nios2: fix cache coherency"
* tag 'nios2-v4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2:
nios2: fix cache coherency
Linus Torvalds [Fri, 27 Nov 2015 18:08:31 +0000 (10:08 -0800)]
Merge tag 'arc-4.4-rc3-fixes' of git://git./linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
- Fix for perf callgraph unwinding causing RCU stalls
- Fix to enable Linux to run on non-default Interrupt priority 0
- Removal of pointless SYNC from __switch_to()
* tag 'arc-4.4-rc3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: dw2 unwind: Remove falllback linear search thru FDE entries
ARC: remove SYNC from __switch_to()
ARCv2: Use the default irq priority for idle sleep
ARC: Abstract out ISA specific SLEEP args
ARC: comments update
ARC: switch to arc-linux- CROSS_COMPILE prefix across all configs
Rafael J. Wysocki [Fri, 27 Nov 2015 15:23:59 +0000 (16:23 +0100)]
Merge branches 'pm-cpufreq' and 'acpi-cppc'
* pm-cpufreq:
intel_pstate: Fix "performance" mode behavior with HWP enabled
cpufreq: SCPI: Depend on SCPI clk driver
cpufreq: intel_pstate: Fix limits->max_perf rounding error
cpufreq: intel_pstate: Fix limits->max_policy_pct rounding error
cpufreq: Always remove sysfs cpuX/cpufreq link on ->remove_dev()
* acpi-cppc:
cpufreq: CPPC: Initialize and check CPUFreq CPU co-ord type correctly
Linus Torvalds [Thu, 26 Nov 2015 19:42:25 +0000 (11:42 -0800)]
Merge tag 'for-linus-4.4-rc2-tag' of git://git./linux/kernel/git/xen/tip
Pull xen bug fixes from David Vrabel:
- Fix gntdev and numa balancing.
- Fix x86 boot crash due to unallocated legacy irq descs.
- Fix overflow in evtchn device when > 1024 event channels.
* tag 'for-linus-4.4-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/evtchn: dynamically grow pending event channel ring
xen/events: Always allocate legacy interrupts on PV guests
xen/gntdev: Grant maps should not be subject to NUMA balancing
Linus Torvalds [Thu, 26 Nov 2015 19:19:59 +0000 (11:19 -0800)]
Merge tag 'powerpc-4.4-3' of git://git./linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- tm: Block signal return from setting invalid MSR state from Michael
Neuling
- tm: Check for already reclaimed tasks from Michael Neuling
* tag 'powerpc-4.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/tm: Check for already reclaimed tasks
powerpc/tm: Block signal return setting invalid MSR state
David Vrabel [Thu, 26 Nov 2015 16:14:35 +0000 (16:14 +0000)]
xen/evtchn: dynamically grow pending event channel ring
If more than 1024 event channels are bound to a evtchn device then it
possible (even with well behaved applications) for the ring to
overflow and events to be lost (reported as an -EFBIG error).
Dynamically increase the size of the ring so there is always enough
space for all bound events. Well behaved applicables that only unmask
events after draining them from the ring can thus no longer lose
events.
However, an application could unmask an event before draining it,
allowing multiple entries per port to accumulate in the ring, and a
overflow could still occur. So the overflow detection and reporting
is retained.
The ring size is initially only 64 entries so the common use case of
an application only binding a few events will use less memory than
before. The ring size may grow to 512 KiB (enough for all 2^17
possible channels). This order 7 kmalloc() may fail due to memory
fragmentation, so we fall back to trying vmalloc().
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Andrew Cooper <andrew.cooper3@citrix.com>
Ard Biesheuvel [Mon, 23 Nov 2015 07:43:24 +0000 (08:43 +0100)]
arm64: efi: fix initcall return values
Even though initcall return values are typically ignored, the
prototype is to return 0 on success or a negative errno value on
error. So fix the arm_enable_runtime_services() implementation to
return 0 on conditions that are not in fact errors, and return a
meaningful error code otherwise.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Ard Biesheuvel [Mon, 23 Nov 2015 07:43:23 +0000 (08:43 +0100)]
arm64: efi: deal with NULL return value of early_memremap()
Add NULL return value checks to two invocations of early_memremap()
in the UEFI init code. For the UEFI configuration tables, we just
warn since we have a better chance of being able to report the issue
in a way that can actually be noticed by a human operator if we don't
abort right away. For the UEFI memory map, however, all we can do is
panic() since we cannot proceed without a description of memory.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Suzuki K. Poulose [Wed, 18 Nov 2015 17:08:58 +0000 (17:08 +0000)]
arm64: debug: Treat the BRPs/WRPs as unsigned
IDAA64DFR0_EL1: BRPs and WRPs are unsigned values. Use
the appropriate helpers to extract those fields.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reported-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Suzuki K. Poulose [Wed, 18 Nov 2015 17:08:57 +0000 (17:08 +0000)]
arm64: cpufeature: Track unsigned fields
Some of the feature bits have unsigned values and need
to be treated accordingly to avoid errors. Adds the property
to the feature bits and use the appropriate field extract helpers.
Reported-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Boris Ostrovsky [Fri, 20 Nov 2015 16:25:04 +0000 (11:25 -0500)]
xen/events: Always allocate legacy interrupts on PV guests
After commit
8c058b0b9c34 ("x86/irq: Probe for PIC presence before
allocating descs for legacy IRQs") early_irq_init() will no longer
preallocate descriptors for legacy interrupts if PIC does not
exist, which is the case for Xen PV guests.
Therefore we may need to allocate those descriptors ourselves.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Suzuki K. Poulose [Wed, 18 Nov 2015 17:08:56 +0000 (17:08 +0000)]
arm64: cpufeature: Add helpers for extracting unsigned values
The cpuid_feature_extract_field() extracts the feature value
as a signed integer. This could be problematic for features
whose values are unsigned. e.g, ID_AA64DFR0_EL1:BRPs. Add
an unsigned variant for the unsigned fields.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reported-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Boris Ostrovsky [Tue, 10 Nov 2015 20:10:33 +0000 (15:10 -0500)]
xen/gntdev: Grant maps should not be subject to NUMA balancing
Doing so will cause the grant to be unmapped and then, during
fault handling, the fault to be mistakenly treated as NUMA hint
fault.
In addition, even if those maps could partcipate in NUMA
balancing, it wouldn't provide any benefit since we are unable
to determine physical page's node (even if/when VNUMA is
implemented).
Marking grant maps' VMAs as VM_IO will exclude them from being
part of NUMA balancing.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Catalin Marinas [Thu, 26 Nov 2015 15:42:41 +0000 (15:42 +0000)]
Revert "arm64: Mark kernel page ranges contiguous"
This reverts commit
348a65cdcbbf243073ee39d1f7d4413081ad7eab.
Incorrect page table manipulation that does not respect the ARM ARM
recommended break-before-make sequence may lead to TLB conflicts. The
contiguous PTE patch makes the system even more susceptible to such
errors by changing the mapping from a single page to a contiguous range
of pages. An additional TLB invalidation would reduce the risk window,
however, the correct fix is to switch to a temporary swapper_pg_dir.
Once the correct workaround is done, the reverted commit will be
re-applied.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Jeremy Linton <jeremy.linton@arm.com>
Will Deacon [Thu, 26 Nov 2015 13:49:39 +0000 (13:49 +0000)]
arm64: mm: keep reserved ASIDs in sync with mm after multiple rollovers
Under some unusual context-switching patterns, it is possible to end up
with multiple threads from the same mm running concurrently with
different ASIDs:
1. CPU x schedules task t with mm p containing ASID a and generation g
This task doesn't block and the CPU doesn't context switch.
So:
* per_cpu(active_asid, x) = {g,a}
* p->context.id = {g,a}
2. Some other CPU generates an ASID rollover. The global generation is
now (g + 1). CPU x is still running t, with no context switch and
so per_cpu(reserved_asid, x) = {g,a}
3. CPU y schedules task t', which shares mm p with t. The generation
mismatches, so we take the slowpath and hit the reserved ASID from
CPU x. p is then updated so that p->context.id = {g + 1,a}
4. CPU y schedules some other task u, which has an mm != p.
5. Some other CPU generates *another* CPU rollover. The global
generation is now (g + 2). CPU x is still running t, with no context
switch and so per_cpu(reserved_asid, x) = {g,a}.
6. CPU y once again schedules task t', but now *fails* to hit the
reserved ASID from CPU x because of the generation mismatch. This
results in a new ASID being allocated, despite the fact that t is
still running on CPU x with the same mm.
Consequently, TLBIs (e.g. as a result of CoW) will not be synchronised
between the two threads.
This patch fixes the problem by updating all of the matching reserved
ASIDs when we hit on the slowpath (i.e. in step 3 above). This keeps
the reserved ASIDs in-sync with the mm and avoids the problem.
Reported-by: Tony Thompson <anthony.thompson@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Andrey Ryabinin [Tue, 17 Nov 2015 15:47:08 +0000 (18:47 +0300)]
arm64: KASAN depends on !(ARM64_16K_PAGES && ARM64_VA_BITS_48)
On KASAN + 16K_PAGES + 48BIT_VA
arch/arm64/mm/kasan_init.c: In function ‘kasan_early_init’:
include/linux/compiler.h:484:38: error: call to ‘__compiletime_assert_95’ declared with attribute error: BUILD_BUG_ON failed: !IS_ALIGNED(KASAN_SHADOW_END, PGDIR_SIZE)
_compiletime_assert(condition, msg, __compiletime_assert_, __LINE__)
Currently KASAN will not work on 16K_PAGES and 48BIT_VA, so
forbid such configuration to avoid above build failure.
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Reported-by: Suzuki K. Poulose <Suzuki.Poulose@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Ley Foon Tan [Thu, 26 Nov 2015 14:25:58 +0000 (22:25 +0800)]
nios2: fix cache coherency
There is intermittent cache coherency issue caught in toolchian tests.
Revert to use flushd.
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Linus Torvalds [Wed, 25 Nov 2015 23:11:08 +0000 (15:11 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A couple of fixes for sendfile lockups caught by Dmitry + a fix for
ancient sysvfs symlink breakage"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vfs: Avoid softlockups with sendfile(2)
vfs: Make sendfile(2) killable even better
fix sysvfs symlinks
Alexandra Yates [Wed, 18 Nov 2015 22:58:40 +0000 (14:58 -0800)]
intel_pstate: Fix "performance" mode behavior with HWP enabled
If hardware-driven P-state selection (HWP) is enabled, the
"performance" mode of intel_pstate should only allow the processor
to use the highest-performance P-state available. That is not
the case currently, so make it actually happen.
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Alexandra Yates <alexandra.yates@linux.intel.com>
[ rjw: Subject and changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Torvalds [Wed, 25 Nov 2015 19:08:35 +0000 (11:08 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull more block layer fixes from Jens Axboe:
"I wasn't going to send off a new pull before next week, but the blk
flush fix from Jan from the other day introduced a regression. It's
rare enough not to have hit during testing, since it requires both a
device that rejects the first flush, and bad timing while it does
that. But since someone did hit it, let's get the revert into 4.4-rc3
so we don't have a released rc with that known issue.
Apart from that revert, three other fixes:
- From Christoph, a fix for a missing unmap in NVMe request
preparation.
- An NVMe fix from Nishanth that fixes data corruption on powerpc.
- Also from Christoph, fix a list_del() attempt on blk-mq that didn't
have a matching list_add() at timer start"
* 'for-linus' of git://git.kernel.dk/linux-block:
Revert "blk-flush: Queue through IO scheduler when flush not required"
block: fix blk_abort_request for blk-mq drivers
nvme: add missing unmaps in nvme_queue_rq
NVMe: default to 4k device page size
Jens Axboe [Wed, 25 Nov 2015 17:12:54 +0000 (10:12 -0700)]
Revert "blk-flush: Queue through IO scheduler when flush not required"
This reverts commit
1b2ff19e6a957b1ef0f365ad331b608af80e932e.
Jan writes:
--
Thanks for report! After some investigation I found out we allocate
elevator specific data in __get_request() only for non-flush requests. And
this is actually required since the flush machinery uses the space in
struct request for something else. Doh. So my patch is just wrong and not
easy to fix since at the time __get_request() is called we are not sure
whether the flush machinery will be used in the end. Jens, please revert
1b2ff19e6a957b1ef0f365ad331b608af80e932e. Thanks!
I'm somewhat surprised that you can reliably hit the race where flushing
gets disabled for the device just while the request is in flight. But I
guess during boot it makes some sense.
--
So let's just revert it, we can fix the queue run manually after the
fact. This race is rare enough that it didn't trigger in testing, it
requires the specific disable-while-in-flight scenario to trigger.
Linus Torvalds [Wed, 25 Nov 2015 17:01:49 +0000 (09:01 -0800)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Bug fixes for all architectures. Nothing really stands out"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (21 commits)
KVM: nVMX: remove incorrect vpid check in nested invvpid emulation
arm64: kvm: report original PAR_EL1 upon panic
arm64: kvm: avoid %p in __kvm_hyp_panic
KVM: arm/arm64: vgic: Trust the LR state for HW IRQs
KVM: arm/arm64: arch_timer: Preserve physical dist. active state on LR.active
KVM: arm/arm64: Fix preemptible timer active state crazyness
arm64: KVM: Add workaround for Cortex-A57 erratum 834220
arm64: KVM: Fix AArch32 to AArch64 register mapping
ARM/arm64: KVM: test properly for a PTE's uncachedness
KVM: s390: fix wrong lookup of VCPUs by array index
KVM: s390: avoid memory overwrites on emergency signal injection
KVM: Provide function for VCPU lookup by id
KVM: s390: fix pfmf intercept handler
KVM: s390: enable SIMD only when no VCPUs were created
KVM: x86: request interrupt window when IRQ chip is split
KVM: x86: set KVM_REQ_EVENT on local interrupt request from user space
KVM: x86: split kvm_vcpu_ready_for_interrupt_injection out of dm_request_for_irq_injection
KVM: x86: fix interrupt window handling in split IRQ chip case
MIPS: KVM: Uninit VCPU in vcpu_create error path
MIPS: KVM: Fix CACHE immediate offset sign extension
...
Mark Rutland [Mon, 23 Nov 2015 11:09:11 +0000 (11:09 +0000)]
arm64: efi: correctly map runtime regions
The kernel may use a page granularity of 4K, 16K, or 64K depending on
configuration.
When mapping EFI runtime regions, we use memrange_efi_to_native to round
the physical base address of a region down to a kernel page boundary,
and round the size up to a kernel page boundary, adding the residue left
over from rounding down the physical base address. We do not round down
the virtual base address.
In __create_mapping we account for the offset of the virtual base from a
granule boundary, adding the residue to the size before rounding the
base down to said granule boundary.
Thus we account for the residue twice, and when the residue is non-zero
will cause __create_mapping to map an additional page at the end of the
region. Depending on the memory map, this page may be in a region we are
not intended/permitted to map, or may clash with a different region that
we wish to map. In typical cases, mapping the next item in the memory
map will overwrite the erroneously created entry, as we sort the memory
map in the stub.
As __create_mapping can cope with base addresses which are not page
aligned, we can instead rely on it to map the region appropriately, and
simplify efi_virtmap_init by removing the unnecessary code.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Mark Rutland [Mon, 23 Nov 2015 15:09:36 +0000 (15:09 +0000)]
arm64: mm: fix fault_info table xFSC decoding
We are missing descriptions for some valid xFSC values in the fault info
table (e.g. "TLB conflict abort"), and have erroneous descriptions for
reserved values (e.g. "asynchronous external abort", "debug event").
This patch adds the missing xFSC values, and removes erroneous decoding
of values reserved by the architecture, as described in ARM DDI 0487A.h.
At the same time, fixed the unbalanced brackets for the synchronous
parity error strings in the table.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Arnd Bergmann [Fri, 20 Nov 2015 11:12:21 +0000 (12:12 +0100)]
arm64: fix building without CONFIG_UID16
As reported by Michal Simek, building an ARM64 kernel with CONFIG_UID16
disabled currently fails because the system call table still needs to
reference the individual function entry points that are provided by
kernel/sys_ni.c in this case, and the declarations are hidden inside
of #ifdef CONFIG_UID16:
arch/arm64/include/asm/unistd32.h:57:8: error: 'sys_lchown16' undeclared here (not in a function)
__SYSCALL(__NR_lchown, sys_lchown16)
I believe this problem only exists on ARM64, because older architectures
tend to not need declarations when their system call table is built
in assembly code, while newer architectures tend to not need UID16
support. ARM64 only uses these system calls for compatibility with
32-bit ARM binaries.
This changes the CONFIG_UID16 check into CONFIG_HAVE_UID16, which is
set unconditionally on ARM64 with CONFIG_COMPAT, so we see the
declarations whenever we need them, but otherwise the behavior is
unchanged.
Fixes:
af1839eb4bd4 ("Kconfig: clean up the long arch list for the UID16 config option")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Haozhong Zhang [Wed, 25 Nov 2015 09:21:39 +0000 (17:21 +0800)]
KVM: nVMX: remove incorrect vpid check in nested invvpid emulation
This patch removes the vpid check when emulating nested invvpid
instruction of type all-contexts invalidation. The existing code is
incorrect because:
(1) According to Intel SDM Vol 3, Section "INVVPID - Invalidate
Translations Based on VPID", invvpid instruction does not check
vpid in the invvpid descriptor when its type is all-contexts
invalidation.
(2) According to the same document, invvpid of type all-contexts
invalidation does not require there is an active VMCS, so/and
get_vmcs12() in the existing code may result in a NULL-pointer
dereference. In practice, it can crash both KVM itself and L1
hypervisors that use invvpid (e.g. Xen).
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Suzuki K. Poulose [Fri, 20 Nov 2015 17:45:40 +0000 (17:45 +0000)]
arm64: early_alloc: Fix check for allocation failure
In early_alloc we check if the memblock_alloc failed by checking
the virtual address of the result, which will never fail. This patch
fixes it to check the actual result for failure.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Christoph Hellwig [Fri, 30 Oct 2015 12:47:04 +0000 (20:47 +0800)]
block: fix blk_abort_request for blk-mq drivers
We only added the request to the request list for the !blk-mq case,
so we should only delete it in that case as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Christoph Hellwig [Fri, 16 Oct 2015 05:58:31 +0000 (07:58 +0200)]
nvme: add missing unmaps in nvme_queue_rq
When we fail various metadata related operations in nvme_queue_rq we
need to unmap the data SGL.
Cc: stable@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Nishanth Aravamudan [Tue, 24 Nov 2015 16:55:05 +0000 (09:55 -0700)]
NVMe: default to 4k device page size
We received a bug report recently when DDW (64-bit direct DMA on Power)
is not enabled for NVMe devices. In that case, we fall back to 32-bit
DMA via the IOMMU, which is always done via 4K TCEs (Translation Control
Entries).
The NVMe device driver, though, assumes that the DMA alignment for the
PRP entries will match the device's page size, and that the DMA aligment
matches the kernel's page aligment. On Power, the the IOMMU page size,
as mentioned above, can be 4K, while the device can have a page size of
8K, while the kernel has a page size of 64K. This eventually trips the
BUG_ON in nvme_setup_prps(), as we have a 'dma_len' that is a multiple
of 4K but not 8K (e.g., 0xF000).
In this particular case of page sizes, we clearly want to use the
IOMMU's page size in the driver. And generally, the NVMe driver in this
function should be using the IOMMU's page size for the default device
page size, rather than the kernel's page size. There is not currently an
API to obtain the IOMMU's page size across all architectures and in the
interest of a stop-gap fix to this functional issue, default the NVMe
device page size to 4K, with the intent of adding such an API and
implementation across all architectures in the next merge window.
With the functionally equivalent v3 of this patch, our hardware test
exerciser survives when using 32-bit DMA; without the patch, the kernel
will BUG within a few minutes.
Signed-off-by: Nishanth Aravamudan <nacc at linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Linus Torvalds [Tue, 24 Nov 2015 20:53:11 +0000 (12:53 -0800)]
Merge tag 'dm-4.4-fixes' of git://git./linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"Two fixes for 4.4-rc1's DM ioctl changes that introduced the potential
for infinite recursion on ioctl (with DM multipath).
And four stable fixes:
- A DM thin-provisioning fix to restore 'error_if_no_space' setting
when a thin-pool is made writable again (after having been out of
space).
- A DM thin-provisioning fix to properly advertise discard support
for thin volumes that are stacked on a thin-pool whose underlying
data device doesn't support discards.
- A DM ioctl fix to allow ctrl-c to break out of an ioctl retry loop
when DM multipath is configured to 'queue_if_no_path'.
- A DM crypt fix for a possible hang on dm-crypt device removal"
* tag 'dm-4.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm thin: fix regression in advertised discard limits
dm crypt: fix a possible hang due to race condition on exit
dm mpath: fix infinite recursion in ioctl when no paths and !queue_if_no_path
dm: do not reuse dm_blk_ioctl block_device input as local variable
dm: fix ioctl retry termination with signal
dm thin: restore requested 'error_if_no_space' setting on OODS to WRITE transition
Eric Dumazet [Tue, 24 Nov 2015 19:39:54 +0000 (11:39 -0800)]
pidns: fix NULL dereference in __task_pid_nr_ns()
I got a crash during a "perf top" session that was caused by a race in
__task_pid_nr_ns() :
pid_nr_ns() was inlined, but apparently compiler chose to read
task->pids[type].pid twice, and the pid->level dereference crashed
because we got a NULL pointer at the second read :
if (pid && ns->level <= pid->level) { // CRASH
Just use RCU API properly to solve this race, and not worry about "perf
top" crashing hosts :(
get_task_pid() can benefit from same fix.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Takashi Iwai [Tue, 24 Nov 2015 19:02:12 +0000 (20:02 +0100)]
ALSA: hda - Fix noise on Gigabyte Z170X mobo
Gigabyte Z710X mobo with ALC1150 codec gets significant noises from
the analog loopback routes even if their inputs are all muted.
Simply kill the aamix for fixing it.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=108301
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Paolo Bonzini [Tue, 24 Nov 2015 18:34:40 +0000 (19:34 +0100)]
Merge tag 'kvm-arm-for-v4.4-rc3' of git://git./linux/kernel/git/kvmarm/kvmarm into kvm-master
KVM/ARM Fixes for v4.4-rc3.
Includes some timer fixes, properly unmapping PTEs, an errata fix, and two
tweaks to the EL2 panic code.
Linus Torvalds [Tue, 24 Nov 2015 18:26:30 +0000 (10:26 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block layer fixes from Jens Axboe:
"A round of fixes/updates for the current series.
This looks a little bigger than it is, but that's mainly because we
pushed the lightnvm enabled null_blk change out of the merge window so
it could be updated a bit. The rest of the volume is also mostly
lightnvm. In particular:
- Lightnvm. Various fixes, additions, updates from Matias and
Javier, as well as from Wenwei Tao.
- NVMe:
- Fix for potential arithmetic overflow from Keith.
- Also from Keith, ensure that we reap pending completions from
a completion queue before deleting it. Fixes kernel crashes
when resetting a device with IO pending.
- Various little lightnvm related tweaks from Matias.
- Fixup flushes to go through the IO scheduler, for the cases where a
flush is not required. Fixes a case in CFQ where we would be
idling and not see this request, hence not break the idling. From
Jan Kara.
- Use list_{first,prev,next} in elevator.c for cleaner code. From
Gelian Tang.
- Fix for a warning trigger on btrfs and raid on single queue blk-mq
devices, where we would flush plug callbacks with preemption
disabled. From me.
- A mac partition validation fix from Kees Cook.
- Two merge fixes from Ming, marked stable. A third part is adding a
new warning so we'll notice this quicker in the future, if we screw
up the accounting.
- Cleanup of thread name/creation in mtip32xx from Rasmus Villemoes"
* 'for-linus' of git://git.kernel.dk/linux-block: (32 commits)
blk-merge: warn if figured out segment number is bigger than nr_phys_segments
blk-merge: fix blk_bio_segment_split
block: fix segment split
blk-mq: fix calling unplug callbacks with preempt disabled
mac: validate mac_partition is within sector
mtip32xx: use formatting capability of kthread_create_on_node
NVMe: reap completion entries when deleting queue
lightnvm: add free and bad lun info to show luns
lightnvm: keep track of block counts
nvme: lightnvm: use admin queues for admin cmds
lightnvm: missing free on init error
lightnvm: wrong return value and redundant free
null_blk: do not del gendisk with lightnvm
null_blk: use device addressing mode
null_blk: use ppa_cache pool
NVMe: Fix possible arithmetic overflow for max segments
blk-flush: Queue through IO scheduler when flush not required
null_blk: register as a LightNVM device
elevator: use list_{first,prev,next}_entry
lightnvm: cleanup queue before target removal
...
Mark Rutland [Mon, 16 Nov 2015 13:58:29 +0000 (13:58 +0000)]
arm64: kvm: report original PAR_EL1 upon panic
If we call __kvm_hyp_panic while a guest context is active, we call
__restore_sysregs before acquiring the system register values for the
panic, in the process throwing away the PAR_EL1 value at the point of
the panic.
This patch modifies __kvm_hyp_panic to stash the PAR_EL1 value prior to
restoring host register values, enabling us to report the original
values at the point of the panic.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Mark Rutland [Mon, 16 Nov 2015 13:55:51 +0000 (13:55 +0000)]
arm64: kvm: avoid %p in __kvm_hyp_panic
Currently __kvm_hyp_panic uses %p for values which are not pointers,
such as the ESR value. This can confusingly lead to "(null)" being
printed for the value.
Use %x instead, and only use %p for host pointers.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Christoffer Dall [Tue, 24 Nov 2015 15:34:31 +0000 (16:34 +0100)]
KVM: arm/arm64: vgic: Trust the LR state for HW IRQs
We were probing the physial distributor state for the active state of a
HW virtual IRQ, because we had seen evidence that the LR state was not
cleared when the guest deactivated a virtual interrupted.
However, this issue turned out to be a software bug in the GIC, which
was solved by:
84aab5e68c2a5e1e18d81ae8308c3ce25d501b29
(KVM: arm/arm64: arch_timer: Preserve physical dist. active
state on LR.active, 2015-11-24)
Therefore, get rid of the complexities and just look at the LR.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Christoffer Dall [Tue, 24 Nov 2015 15:23:05 +0000 (16:23 +0100)]
KVM: arm/arm64: arch_timer: Preserve physical dist. active state on LR.active
We were incorrectly removing the active state from the physical
distributor on the timer interrupt when the timer output level was
deasserted. We shouldn't be doing this without considering the virtual
interrupt's active state, because the architecture requires that when an
LR has the HW bit set and the pending or active bits set, then the
physical interrupt must also have the corresponding bits set.
This addresses an issue where we have been observing an inconsistency
between the LR state and the physical distributor state where the LR
state was active and the physical distributor was not active, which
shouldn't happen.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Christoffer Dall [Tue, 24 Nov 2015 09:31:07 +0000 (10:31 +0100)]
KVM: arm/arm64: Fix preemptible timer active state crazyness
We were setting the physical active state on the GIC distributor in a
preemptible section, which could cause us to set the active state on
different physical CPU from the one we were actually going to run on,
hacoc ensues.
Since we are no longer descheduling/scheduling soft timers in the
flush/sync timer functions, simply moving the timer flush into a
non-preemptible section.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Marc Zyngier [Mon, 16 Nov 2015 10:28:18 +0000 (10:28 +0000)]
arm64: KVM: Add workaround for Cortex-A57 erratum 834220
Cortex-A57 parts up to r1p2 can misreport Stage 2 translation faults
when a Stage 1 permission fault or device alignment fault should
have been reported.
This patch implements the workaround (which is to validate that the
Stage-1 translation actually succeeds) by using code patching.
Cc: stable@vger.kernel.org
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Marc Zyngier [Mon, 16 Nov 2015 10:28:17 +0000 (10:28 +0000)]
arm64: KVM: Fix AArch32 to AArch64 register mapping
When running a 32bit guest under a 64bit hypervisor, the ARMv8
architecture defines a mapping of the 32bit registers in the 64bit
space. This includes banked registers that are being demultiplexed
over the 64bit ones.
On exceptions caused by an operation involving a 32bit register, the
HW exposes the register number in the ESR_EL2 register. It was so
far understood that SW had to distinguish between AArch32 and AArch64
accesses (based on the current AArch32 mode and register number).
It turns out that I misinterpreted the ARM ARM, and the clue is in
D1.20.1: "For some exceptions, the exception syndrome given in the
ESR_ELx identifies one or more register numbers from the issued
instruction that generated the exception. Where the exception is
taken from an Exception level using AArch32 these register numbers
give the AArch64 view of the register."
Which means that the HW is already giving us the translated version,
and that we shouldn't try to interpret it at all (for example, doing
an MMIO operation from the IRQ mode using the LR register leads to
very unexpected behaviours).
The fix is thus not to perform a call to vcpu_reg32() at all from
vcpu_reg(), and use whatever register number is supplied directly.
The only case we need to find out about the mapping is when we
actively generate a register access, which only occurs when injecting
a fault in a guest.
Cc: stable@vger.kernel.org
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Ard Biesheuvel [Tue, 10 Nov 2015 14:11:20 +0000 (15:11 +0100)]
ARM/arm64: KVM: test properly for a PTE's uncachedness
The open coded tests for checking whether a PTE maps a page as
uncached use a flawed '(pte_val(xxx) & CONST) != CONST' pattern,
which is not guaranteed to work since the type of a mapping is
not a set of mutually exclusive bits
For HYP mappings, the type is an index into the MAIR table (i.e, the
index itself does not contain any information whatsoever about the
type of the mapping), and for stage-2 mappings it is a bit field where
normal memory and device types are defined as follows:
#define MT_S2_NORMAL 0xf
#define MT_S2_DEVICE_nGnRE 0x1
I.e., masking *and* comparing with the latter matches on the former,
and we have been getting lucky merely because the S2 device mappings
also have the PTE_UXN bit set, or we would misidentify memory mappings
as device mappings.
Since the unmap_range() code path (which contains one instance of the
flawed test) is used both for HYP mappings and stage-2 mappings, and
considering the difference between the two, it is non-trivial to fix
this by rewriting the tests in place, as it would involve passing
down the type of mapping through all the functions.
However, since HYP mappings and stage-2 mappings both deal with host
physical addresses, we can simply check whether the mapping is backed
by memory that is managed by the host kernel, and only perform the
D-cache maintenance if this is the case.
Cc: stable@vger.kernel.org
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Hui Wang [Tue, 24 Nov 2015 03:08:18 +0000 (11:08 +0800)]
ALSA: hda - Fix headphone noise after Dell XPS 13 resume back from S3
We have a machine Dell XPS 13 with the codec alc256, after resume back
from S3, the headphone has noise when play sound.
Through comparing with the coeff vaule before and after S3, we found
restoring a coeff register will help remove noise.
BugLink: https://bugs.launchpad.net/bugs/1519168
Cc: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Ming Lei [Tue, 24 Nov 2015 02:35:31 +0000 (10:35 +0800)]
blk-merge: warn if figured out segment number is bigger than nr_phys_segments
We had seen lots of reports of this kind issue, so add one
warnning in blk-merge, then it can be triggered easily and
avoid to depend on warning/bug from drivers.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Ming Lei [Tue, 24 Nov 2015 02:35:30 +0000 (10:35 +0800)]
blk-merge: fix blk_bio_segment_split
Commit
bdced438acd83a(block: setup bi_phys_segments after
splitting) introduces function of computing bio->bi_phys_segments
during bio splitting.
Unfortunately both bio->bi_seg_front_size and bio->bi_seg_back_size
arn't computed, so too many physical segments may be obtained
for one request since both the two are used to check if one segment
across two bios can be possible.
This patch fixes the issue by computing the two variables in
blk_bio_segment_split().
Fixes:
bdced438acd83a(block: setup bi_phys_segments after splitting)
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Reported-by: Mark Salter <msalter@redhat.com>
Tested-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Tested-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Ming Lei [Tue, 24 Nov 2015 02:35:29 +0000 (10:35 +0800)]
block: fix segment split
Inside blk_bio_segment_split(), previous bvec pointer(bvprvp)
always points to the iterator local variable, which is obviously
wrong, so fix it by pointing to the local variable of 'bvprv'.
Fixes:
5014c311baa2b(block: fix bogus compiler warnings in blk-merge.c)
Cc: stable@kernel.org #4.3
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Reported-by: Mark Salter <msalter@redhat.com>
Tested-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Tested-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Jan Kara [Mon, 23 Nov 2015 12:09:51 +0000 (13:09 +0100)]
vfs: Avoid softlockups with sendfile(2)
The following test program from Dmitry can cause softlockups or RCU
stalls as it copies 1GB from tmpfs into eventfd and we don't have any
scheduling point at that path in sendfile(2) implementation:
int r1 = eventfd(0, 0);
int r2 = memfd_create("", 0);
unsigned long n = 1<<30;
fallocate(r2, 0, 0, n);
sendfile(r1, r2, 0, n);
Add cond_resched() into __splice_from_pipe() to fix the problem.
CC: Dmitry Vyukov <dvyukov@google.com>
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Jan Kara [Mon, 23 Nov 2015 12:09:50 +0000 (13:09 +0100)]
vfs: Make sendfile(2) killable even better
Commit
296291cdd162 (mm: make sendfile(2) killable) fixed an issue where
sendfile(2) was doing a lot of tiny writes into a filesystem and thus
was unkillable for a long time. However sendfile(2) can be (mis)used to
issue lots of writes into arbitrary file descriptor such as evenfd or
similar special file descriptors which never hit the standard filesystem
write path and thus are still unkillable. E.g. the following example
from Dmitry burns CPU for ~16s on my test system without possibility to
be killed:
int r1 = eventfd(0, 0);
int r2 = memfd_create("", 0);
unsigned long n = 1<<30;
fallocate(r2, 0, 0, n);
sendfile(r1, r2, 0, n);
There are actually quite a few tests for pending signals in sendfile
code however we data to write is always available none of them seems to
trigger. So fix the problem by adding a test for pending signal into
splice_from_pipe_next() also before the loop waiting for pipe buffers to
be available. This should fix all the lockup issues with sendfile of the
do-ton-of-tiny-writes nature.
CC: stable@vger.kernel.org
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Tue, 24 Nov 2015 02:11:08 +0000 (21:11 -0500)]
fix sysvfs symlinks
The thing got broken back in 2002 - sysvfs does *not* have inline
symlinks; even short ones have bodies stored in the first block
of file. sysv_symlink() handles that correctly; unfortunately,
attempting to look an existing symlink up will end up confusing
them for inline symlinks, and interpret the block number containing
the body as the body itself.
Nobody has noticed until now, which says something about the level
of testing sysvfs gets ;-/
Cc: stable@vger.kernel.org # all of them, not that anyone cared
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Punit Agrawal [Wed, 18 Nov 2015 13:52:44 +0000 (13:52 +0000)]
cpufreq: SCPI: Depend on SCPI clk driver
The SCPI clk driver registers the virtual cpufreq device that kicks off
initialisation of the SCPI cpufreq driver. Also, clk_get() will fail for
the cpufreq driver if the SCPI clk driver is missing.
Fix this by making the SCPI cpufreq driver explicitly depend on the SCPI
clk driver.
Fixes:
8def31034d03 (cpufreq: arm_big_little: add SCPI interface driver)
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rafael J. Wysocki [Mon, 23 Nov 2015 22:49:57 +0000 (23:49 +0100)]
Merge back earlier cpufreq fixes for v4.4.
Prarit Bhargava [Fri, 20 Nov 2015 23:47:57 +0000 (18:47 -0500)]
cpufreq: intel_pstate: Fix limits->max_perf rounding error
A rounding error was found in the calculation of limits->max_perf
in intel_pstate_set_policy(), which is used to calculate the max and min
pstate values in intel_pstate_get_min_max(). In that code,
limits->max_perf is truncated to 2 hex digits such that, for example,
0x169 was incorrectly calculated to 0x16 instead of 0x17. This resulted in
the pstate being set one level too low. This patch rounds the value of
limits->max_perf up instead of down so that the correct max pstate can
be reached.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Prarit Bhargava [Fri, 20 Nov 2015 23:47:56 +0000 (18:47 -0500)]
cpufreq: intel_pstate: Fix limits->max_policy_pct rounding error
I have a Intel (6,63) processor with a "marketing" frequency (from
/proc/cpuinfo) of 2100MHz, and a max turbo frequency of 2600MHz. I
can execute
cpupower frequency-set -g powersave --min 1200MHz --max 2100MHz
and the max_freq_pct is set to 80. When adding load to the system I noticed
that the cpu frequency only reached 2000MHZ and not 2100MHz as expected.
This is because limits->max_policy_pct is calculated as 2100 * 100 /2600 = 80.7
and is rounded down to 80 when it should be rounded up to 81. This patch
adds a DIV_ROUND_UP() which will return the correct value.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Viresh Kumar [Sat, 21 Nov 2015 03:36:49 +0000 (09:06 +0530)]
cpufreq: Always remove sysfs cpuX/cpufreq link on ->remove_dev()
Subsys interface's ->remove_dev() is called when the cpufreq driver is
unregistering or the CPU is getting physically removed. We keep removing
the cpuX/cpufreq link for all CPUs except the last one, which is a
mistake as all CPUs contain a link now.
Because of this, one CPU from each policy will still contain a link (to
an already removed policyX directory), after the cpufreq driver is
unregistered.
Fix that by removing the link first and then only see if the policy is
required to be freed. That will make sure that no links are left out.
Fixes:
96bdda61f58b ("cpufreq: create cpu/cpufreq/policyX directories")
Reported-and-tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Ashwin Chaugule [Thu, 19 Nov 2015 15:40:07 +0000 (10:40 -0500)]
cpufreq: CPPC: Initialize and check CPUFreq CPU co-ord type correctly
The CPU policy struct indicates the co-ordination type
for all CPUs of a common freq domain. Initialize it
correctly using the CPU specific data gathered from
CPPC ACPI lib via acpi_get_psd_map().
The PSD object is optional, so the cpu->shared_type
can also be 0. So instead of assuming any value other
than SW_ANY(0xFD) is unsupported, explictly check
if shared_type is SW_ALL and then bail.
Signed-off-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Torvalds [Mon, 23 Nov 2015 21:19:27 +0000 (13:19 -0800)]
Merge tag 'linux-kselftest-4.4-rc3' of git://git./linux/kernel/git/shuah/linux-kselftest
Pull kselftest fixes from Shuah Khan:
"This update consists of one minor documentation fix and a fix to an
existing test"
* tag 'linux-kselftest-4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests/seccomp: Get page size from sysconf
tools:testing/selftests: fix typo in futex/README
Mike Snitzer [Mon, 23 Nov 2015 18:44:38 +0000 (13:44 -0500)]
dm thin: fix regression in advertised discard limits
When establishing a thin device's discard limits we cannot rely on the
underlying thin-pool device's discard capabilities (which are inherited
from the thin-pool's underlying data device) given that DM thin devices
must provide discard support even when the thin-pool's underlying data
device doesn't support discards.
Users were exposed to this thin device discard limits regression if
their thin-pool's underlying data device does _not_ support discards.
This regression caused all upper-layers that called the
blkdev_issue_discard() interface to not be able to issue discards to
thin devices (because discard_granularity was 0). This regression
wasn't caught earlier because the device-mapper-test-suite's extensive
'thin-provisioning' discard tests are only ever performed against
thin-pool's with data devices that support discards.
Fix is to have thin_io_hints() test the pool's 'discard_enabled' feature
rather than inferring whether or not a thin device's discard support
should be enabled by looking at the thin-pool's discard_granularity.
Fixes:
216076705 ("dm thin: disable discard support for thin devices if pool's is disabled")
Reported-by: Mike Gerber <mike@sprachgewalt.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 4.1+
Vineet Gupta [Mon, 23 Nov 2015 14:02:51 +0000 (19:32 +0530)]
ARC: dw2 unwind: Remove falllback linear search thru FDE entries
Fixes STAR
9000953410: "perf callgraph profiling causing RCU stalls"
| perf record -g -c 15000 -e cycles /sbin/hackbench
|
| INFO: rcu_preempt self-detected stall on CPU
| 1: (1 GPs behind) idle=609/
140000000000002/0 softirq=2914/2915 fqs=603
| Task dump for CPU 1:
in-kernel dwarf unwinder has a fast binary lookup and a fallback linear
search (which iterates thru each of ~11K entries) thus takes 2 orders of
magnitude longer (~3 million cycles vs. 2000). Routines written in hand
assembler lack dwarf info (as we don't support assembler CFI pseudo-ops
yet) fail the unwinder binary lookup, hit linear search, failing
nevertheless in the end.
However the linear search is pointless as binary lookup tables are created
from it in first place. It is impossible to have binary lookup fail while
succeed the linear search. It is pure waste of cycles thus removed by
this patch.
This manifested as RCU stalls / NMI watchdog splat when running
hackbench under perf with callgraph profiling. The triggering condition
was perf counter overflowing in routine lacking dwarf info (like memset)
leading to patheic 3 million cycle unwinder slow path and by the time it
returned new interrupts were already pending (Timer, IPI) and taken
rightaway. The original memset didn't make forward progress, system kept
accruing more interrupts and more unwinder delayes in a vicious feedback
loop, ultimately triggering the NMI diagnostic.
Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Michael Neuling [Thu, 19 Nov 2015 04:44:45 +0000 (15:44 +1100)]
powerpc/tm: Check for already reclaimed tasks
Currently we can hit a scenario where we'll tm_reclaim() twice. This
results in a TM bad thing exception because the second reclaim occurs
when not in suspend mode.
The scenario in which this can happen is the following. We attempt to
deliver a signal to userspace. To do this we need obtain the stack
pointer to write the signal context. To get this stack pointer we
must tm_reclaim() in case we need to use the checkpointed stack
pointer (see get_tm_stackpointer()). Normally we'd then return
directly to userspace to deliver the signal without going through
__switch_to().
Unfortunatley, if at this point we get an error (such as a bad
userspace stack pointer), we need to exit the process. The exit will
result in a __switch_to(). __switch_to() will attempt to save the
process state which results in another tm_reclaim(). This
tm_reclaim() now causes a TM Bad Thing exception as this state has
already been saved and the processor is no longer in TM suspend mode.
Whee!
This patch checks the state of the MSR to ensure we are TM suspended
before we attempt the tm_reclaim(). If we've already saved the state
away, we should no longer be in TM suspend mode. This has the
additional advantage of checking for a potential TM Bad Thing
exception.
Found using syscall fuzzer.
Fixes:
fb09692e71f1 ("powerpc: Add reclaim and recheckpoint functions for context switching transactional memory processes")
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Neuling [Thu, 19 Nov 2015 04:44:44 +0000 (15:44 +1100)]
powerpc/tm: Block signal return setting invalid MSR state
Currently we allow both the MSR T and S bits to be set by userspace on
a signal return. Unfortunately this is a reserved configuration and
will cause a TM Bad Thing exception if attempted (via rfid).
This patch checks for this case in both the 32 and 64 bit signals
code. If both T and S are set, we mark the context as invalid.
Found using a syscall fuzzer.
Fixes:
2b0a576d15e0 ("powerpc: Add new transactional memory state to the signal context")
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Linus Torvalds [Mon, 23 Nov 2015 00:45:59 +0000 (16:45 -0800)]
Linux 4.4-rc2
Linus Torvalds [Sun, 22 Nov 2015 23:21:40 +0000 (15:21 -0800)]
Merge branch 'akpm' (patches from Andrew)
Merge slub bulk allocator updates from Andrew Morton:
"This missed the merge window because I was waiting for some repairs to
come in. Nothing actually uses the bulk allocator yet and the changes
to other code paths are pretty small. And the net guys are waiting
for this so they can start merging the client code"
More comments from Jesper Dangaard Brouer:
"The kmem_cache_alloc_bulk() call, in mm/slub.c, were included in
previous kernel. The present version contains a bug. Vladimir
Davydov noticed it contained a bug, when kernel is compiled with
CONFIG_MEMCG_KMEM (see commit
03ec0ed57ffc: "slub: fix kmem cgroup
bug in kmem_cache_alloc_bulk"). Plus the mem cgroup counterpart in
kmem_cache_free_bulk() were missing (see commit
033745189b1b "slub:
add missing kmem cgroup support to kmem_cache_free_bulk").
I don't consider the fix stable-material because there are no in-tree
users of the API.
But with known bugs (for memcg) I cannot start using the API in the
net-tree"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
slab/slub: adjust kmem_cache_alloc_bulk API
slub: add missing kmem cgroup support to kmem_cache_free_bulk
slub: fix kmem cgroup bug in kmem_cache_alloc_bulk
slub: optimize bulk slowpath free by detached freelist
slub: support for bulk free with SLUB freelists
Linus Torvalds [Sun, 22 Nov 2015 23:10:57 +0000 (15:10 -0800)]
Merge tag 'tty-4.4-rc2' of git://git./linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are a few small tty/serial driver fixes for 4.4-rc2 that resolve
some reported problems.
All have been in linux-next, full details are in the shortlog below"
* tag 'tty-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: export fsl8250_handle_irq
serial: 8250_mid: Add missing dependency
tty: audit: Fix audit source
serial: etraxfs-uart: Fix crash
serial: fsl_lpuart: Fix earlycon support
bcm63xx_uart: Use the device name when registering an interrupt
tty: Fix direct use of tty buffer work
tty: Fix tty_send_xchar() lock order inversion
Linus Torvalds [Sun, 22 Nov 2015 21:26:24 +0000 (13:26 -0800)]
Merge tag 'staging-4.4-rc2' of git://git./linux/kernel/git/gregkh/staging
Pull staging/IIO fixes from Greg KH:
"Here are some staging and iio driver fixes for 4.4-rc2. All of these
are in response to issues that have been reported and have been in
linux-next for a while"
* tag 'staging-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
Revert "Staging: wilc1000: coreconfigurator: Drop unneeded wrapper functions"
iio: adc: xilinx: Fix VREFN scale
iio: si7020: Swap data byte order
iio: adc: vf610_adc: Fix division by zero error
iio:ad7793: Fix ad7785 product ID
iio: ad5064: Fix ad5629/ad5669 shift
iio:ad5064: Make sure ad5064_i2c_write() returns 0 on success
iio: lpc32xx_adc: fix warnings caused by enabling unprepared clock
staging: iio: select IRQ_WORK for IIO_DUMMY_EVGEN
vf610_adc: Fix internal temperature calculation
Linus Torvalds [Sun, 22 Nov 2015 21:15:05 +0000 (13:15 -0800)]
Merge tag 'usb-4.4-rc2' of git://git./linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of USB fixes and new device ids for 4.4-rc2. All
have been in linux-next and the details are in the shortlog"
* tag 'usb-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (28 commits)
usblp: do not set TASK_INTERRUPTIBLE before lock
USB: MAINTAINERS: cxacru
usb: kconfig: fix warning of select USB_OTG
USB: option: add XS Stick W100-2 from 4G Systems
xhci: Fix a race in usb2 LPM resume, blocking U3 for usb2 devices
usb: xhci: fix checking ep busy for CFC
xhci: Workaround to get Intel xHCI reset working more reliably
usb: chipidea: imx: fix a possible NULL dereference
usb: chipidea: usbmisc_imx: fix a possible NULL dereference
usb: chipidea: otg: gadget module load and unload support
usb: chipidea: debug: disable usb irq while role switch
ARM: dts: imx27.dtsi: change the clock information for usb
usb: chipidea: imx: refine clock operations to adapt for all platforms
usb: gadget: atmel_usba_udc: Expose correct device speed
usb: musb: enable usb_dma parameter
usb: phy: phy-mxs-usb: fix a possible NULL dereference
usb: dwc3: gadget: let us set lower max_speed
usb: musb: fix tx fifo flush handling
usb: gadget: f_loopback: fix the warning during the enumeration
usb: dwc2: host: Fix remote wakeup when not in DWC2_L2
...
Linus Torvalds [Sun, 22 Nov 2015 20:59:46 +0000 (12:59 -0800)]
Merge branch 'upstream' of git://git.linux-mips.org/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
- Fix a flood of annoying build warnings
- A number of fixes for Atheros 79xx platforms
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: ath79: Add a machine entry for booting OF machines
MIPS: ath79: Fix the size of the MISC INTC registers in ar9132.dtsi
MIPS: ath79: Fix the DDR control initialization on ar71xx and ar934x
MIPS: Fix flood of warnings about comparsion being always true.
Linus Torvalds [Sun, 22 Nov 2015 20:50:58 +0000 (12:50 -0800)]
Merge branch 'parisc-4.4-2' of git://git./linux/kernel/git/deller/parisc-linux
Pull parisc update from Helge Deller:
"This patchset adds Huge Page and HUGETLBFS support for parisc"
Honestly, the hugepage support should have gone through in the merge
window, and is not really an rc-time fix. But it only touches
arch/parisc, and I cannot find it in myself to care. If one of the
three parisc users notices a breakage, I will point at Helge and make
rude farting noises.
* 'parisc-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Map kernel text and data on huge pages
parisc: Add Huge Page and HUGETLBFS support
parisc: Use long branch to do_syscall_trace_exit
parisc: Increase initial kernel mapping to 32MB on 64bit kernel
parisc: Initialize the fault vector earlier in the boot process.
parisc: Add defines for Huge page support
parisc: Drop unused MADV_xxxK_PAGES flags from asm/mman.h
parisc: Drop definition of start_thread_som for HP-UX SOM binaries
parisc: Fix wrong comment regarding first pmd entry flags
Linus Torvalds [Sun, 22 Nov 2015 20:37:20 +0000 (12:37 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf tool fixes from Thomas Gleixner:
"A couple of fixes for perf tools:
- Build system updates
- Plug a memory leak in an error path of perf probe
- Tear down probes correctly when adding fails
- Fixes to the perf symbol handling
- Fix ordering of event processing in buildid-list
- Fix per DSO filtering in the histogram browser"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf probe: Clear probe_trace_event when add_probe_trace_event() fails
perf probe: Fix memory leaking on failure by clearing all probe_trace_events
perf inject: Also re-pipe lost_samples event
perf buildid-list: Requires ordered events
perf symbols: Fix dso lookup by long name and missing buildids
perf symbols: Allow forcing reading of non-root owned files by root
perf hists browser: The dso can be obtained from popup_action->ms.map->dso
perf hists browser: Fix 'd' hotkey action to filter by DSO
perf symbols: Rebuild rbtree when adjusting symbols for kcore
tools: Add a "make all" rule
tools: Actually install tmon in the install rule
Linus Torvalds [Sun, 22 Nov 2015 20:00:12 +0000 (12:00 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"This update contains:
- MPX updates for handling 32bit processes
- A fix for a long standing bug in 32bit signal frame handling
related to FPU/XSAVE state
- Handle get_xsave_addr() correctly in KVM
- Fix SMAP check under paravirtualization
- Add a comment to the static function trace entry to avoid further
confusion about the difference to dynamic tracing"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Fix SMAP check in PVOPS environments
x86/ftrace: Add comment on static function tracing
x86/fpu: Fix get_xsave_addr() behavior under virtualization
x86/fpu: Fix 32-bit signal frame handling
x86/mpx: Fix 32-bit address space calculation
x86/mpx: Do proper get_user() when running 32-bit binaries on 64-bit kernels
Jesper Dangaard Brouer [Fri, 20 Nov 2015 23:57:58 +0000 (15:57 -0800)]
slab/slub: adjust kmem_cache_alloc_bulk API
Adjust kmem_cache_alloc_bulk API before we have any real users.
Adjust API to return type 'int' instead of previously type 'bool'. This
is done to allow future extension of the bulk alloc API.
A future extension could be to allow SLUB to stop at a page boundary, when
specified by a flag, and then return the number of objects.
The advantage of this approach, would make it easier to make bulk alloc
run without local IRQs disabled. With an approach of cmpxchg "stealing"
the entire c->freelist or page->freelist. To avoid overshooting we would
stop processing at a slab-page boundary. Else we always end up returning
some objects at the cost of another cmpxchg.
To keep compatible with future users of this API linking against an older
kernel when using the new flag, we need to return the number of allocated
objects with this API change.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jesper Dangaard Brouer [Fri, 20 Nov 2015 23:57:55 +0000 (15:57 -0800)]
slub: add missing kmem cgroup support to kmem_cache_free_bulk
Initial implementation missed support for kmem cgroup support in
kmem_cache_free_bulk() call, add this.
If CONFIG_MEMCG_KMEM is not enabled, the compiler should be smart enough
to not add any asm code.
Incoming bulk free objects can belong to different kmem cgroups, and
object free call can happen at a later point outside memcg context. Thus,
we need to keep the orig kmem_cache, to correctly verify if a memcg object
match against its "root_cache" (s->memcg_params.root_cache).
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jesper Dangaard Brouer [Fri, 20 Nov 2015 23:57:52 +0000 (15:57 -0800)]
slub: fix kmem cgroup bug in kmem_cache_alloc_bulk
The call slab_pre_alloc_hook() interacts with kmemgc and is not allowed to
be called several times inside the bulk alloc for loop, due to the call to
memcg_kmem_get_cache().
This would result in hitting the VM_BUG_ON in __memcg_kmem_get_cache.
As suggested by Vladimir Davydov, change slab_post_alloc_hook() to be able
to handle an array of objects.
A subtle detail is, loop iterator "i" in slab_post_alloc_hook() must have
same type (size_t) as size argument. This helps the compiler to easier
realize that it can remove the loop, when all debug statements inside loop
evaluates to nothing. Note, this is only an issue because the kernel is
compiled with GCC option: -fno-strict-overflow
In slab_alloc_node() the compiler inlines and optimizes the invocation of
slab_post_alloc_hook(s, flags, 1, &object) by removing the loop and access
object directly.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reported-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Suggested-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Reviewed-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jesper Dangaard Brouer [Fri, 20 Nov 2015 23:57:49 +0000 (15:57 -0800)]
slub: optimize bulk slowpath free by detached freelist
This change focus on improving the speed of object freeing in the
"slowpath" of kmem_cache_free_bulk.
The calls slab_free (fastpath) and __slab_free (slowpath) have been
extended with support for bulk free, which amortize the overhead of
the (locked) cmpxchg_double.
To use the new bulking feature, we build what I call a detached
freelist. The detached freelist takes advantage of three properties:
1) the free function call owns the object that is about to be freed,
thus writing into this memory is synchronization-free.
2) many freelist's can co-exist side-by-side in the same slab-page
each with a separate head pointer.
3) it is the visibility of the head pointer that needs synchronization.
Given these properties, the brilliant part is that the detached
freelist can be constructed without any need for synchronization. The
freelist is constructed directly in the page objects, without any
synchronization needed. The detached freelist is allocated on the
stack of the function call kmem_cache_free_bulk. Thus, the freelist
head pointer is not visible to other CPUs.
All objects in a SLUB freelist must belong to the same slab-page.
Thus, constructing the detached freelist is about matching objects
that belong to the same slab-page. The bulk free array is scanned is
a progressive manor with a limited look-ahead facility.
Kmem debug support is handled in call of slab_free().
Notice kmem_cache_free_bulk no longer need to disable IRQs. This
only slowed down single free bulk with approx 3 cycles.
Performance data:
Benchmarked[1] obj size 256 bytes on CPU i7-4790K @ 4.00GHz
SLUB fastpath single object quick reuse: 47 cycles(tsc) 11.931 ns
To get stable and comparable numbers, the kernel have been booted with
"slab_merge" (this also improve performance for larger bulk sizes).
Performance data, compared against fallback bulking:
bulk - fallback bulk - improvement with this patch
1 - 62 cycles(tsc) 15.662 ns - 49 cycles(tsc) 12.407 ns- improved 21.0%
2 - 55 cycles(tsc) 13.935 ns - 30 cycles(tsc) 7.506 ns - improved 45.5%
3 - 53 cycles(tsc) 13.341 ns - 23 cycles(tsc) 5.865 ns - improved 56.6%
4 - 52 cycles(tsc) 13.081 ns - 20 cycles(tsc) 5.048 ns - improved 61.5%
8 - 50 cycles(tsc) 12.627 ns - 18 cycles(tsc) 4.659 ns - improved 64.0%
16 - 49 cycles(tsc) 12.412 ns - 17 cycles(tsc) 4.495 ns - improved 65.3%
30 - 49 cycles(tsc) 12.484 ns - 18 cycles(tsc) 4.533 ns - improved 63.3%
32 - 50 cycles(tsc) 12.627 ns - 18 cycles(tsc) 4.707 ns - improved 64.0%
34 - 96 cycles(tsc) 24.243 ns - 23 cycles(tsc) 5.976 ns - improved 76.0%
48 - 83 cycles(tsc) 20.818 ns - 21 cycles(tsc) 5.329 ns - improved 74.7%
64 - 74 cycles(tsc) 18.700 ns - 20 cycles(tsc) 5.127 ns - improved 73.0%
128 - 90 cycles(tsc) 22.734 ns - 27 cycles(tsc) 6.833 ns - improved 70.0%
158 - 99 cycles(tsc) 24.776 ns - 30 cycles(tsc) 7.583 ns - improved 69.7%
250 - 104 cycles(tsc) 26.089 ns - 37 cycles(tsc) 9.280 ns - improved 64.4%
Performance data, compared current in-kernel bulking:
bulk - curr in-kernel - improvement with this patch
1 - 46 cycles(tsc) - 49 cycles(tsc) - improved (cycles:-3) -6.5%
2 - 27 cycles(tsc) - 30 cycles(tsc) - improved (cycles:-3) -11.1%
3 - 21 cycles(tsc) - 23 cycles(tsc) - improved (cycles:-2) -9.5%
4 - 18 cycles(tsc) - 20 cycles(tsc) - improved (cycles:-2) -11.1%
8 - 17 cycles(tsc) - 18 cycles(tsc) - improved (cycles:-1) -5.9%
16 - 18 cycles(tsc) - 17 cycles(tsc) - improved (cycles: 1) 5.6%
30 - 18 cycles(tsc) - 18 cycles(tsc) - improved (cycles: 0) 0.0%
32 - 18 cycles(tsc) - 18 cycles(tsc) - improved (cycles: 0) 0.0%
34 - 78 cycles(tsc) - 23 cycles(tsc) - improved (cycles:55) 70.5%
48 - 60 cycles(tsc) - 21 cycles(tsc) - improved (cycles:39) 65.0%
64 - 49 cycles(tsc) - 20 cycles(tsc) - improved (cycles:29) 59.2%
128 - 69 cycles(tsc) - 27 cycles(tsc) - improved (cycles:42) 60.9%
158 - 79 cycles(tsc) - 30 cycles(tsc) - improved (cycles:49) 62.0%
250 - 86 cycles(tsc) - 37 cycles(tsc) - improved (cycles:49) 57.0%
Performance with normal SLUB merging is significantly slower for
larger bulking. This is believed to (primarily) be an effect of not
having to share the per-CPU data-structures, as tuning per-CPU size
can achieve similar performance.
bulk - slab_nomerge - normal SLUB merge
1 - 49 cycles(tsc) - 49 cycles(tsc) - merge slower with cycles:0
2 - 30 cycles(tsc) - 30 cycles(tsc) - merge slower with cycles:0
3 - 23 cycles(tsc) - 23 cycles(tsc) - merge slower with cycles:0
4 - 20 cycles(tsc) - 20 cycles(tsc) - merge slower with cycles:0
8 - 18 cycles(tsc) - 18 cycles(tsc) - merge slower with cycles:0
16 - 17 cycles(tsc) - 17 cycles(tsc) - merge slower with cycles:0
30 - 18 cycles(tsc) - 23 cycles(tsc) - merge slower with cycles:5
32 - 18 cycles(tsc) - 22 cycles(tsc) - merge slower with cycles:4
34 - 23 cycles(tsc) - 22 cycles(tsc) - merge slower with cycles:-1
48 - 21 cycles(tsc) - 22 cycles(tsc) - merge slower with cycles:1
64 - 20 cycles(tsc) - 48 cycles(tsc) - merge slower with cycles:28
128 - 27 cycles(tsc) - 57 cycles(tsc) - merge slower with cycles:30
158 - 30 cycles(tsc) - 59 cycles(tsc) - merge slower with cycles:29
250 - 37 cycles(tsc) - 56 cycles(tsc) - merge slower with cycles:19
Joint work with Alexander Duyck.
[1] https://github.com/netoptimizer/prototype-kernel/blob/master/kernel/mm/slab_bulk_test01.c
[akpm@linux-foundation.org: BUG_ON -> WARN_ON;return]
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jesper Dangaard Brouer [Fri, 20 Nov 2015 23:57:46 +0000 (15:57 -0800)]
slub: support for bulk free with SLUB freelists
Make it possible to free a freelist with several objects by adjusting API
of slab_free() and __slab_free() to have head, tail and an objects counter
(cnt).
Tail being NULL indicate single object free of head object. This allow
compiler inline constant propagation in slab_free() and
slab_free_freelist_hook() to avoid adding any overhead in case of single
object free.
This allows a freelist with several objects (all within the same
slab-page) to be free'ed using a single locked cmpxchg_double in
__slab_free() and with an unlocked cmpxchg_double in slab_free().
Object debugging on the free path is also extended to handle these
freelists. When CONFIG_SLUB_DEBUG is enabled it will also detect if
objects don't belong to the same slab-page.
These changes are needed for the next patch to bulk free the detached
freelists it introduces and constructs.
Micro benchmarking showed no performance reduction due to this change,
when debugging is turned off (compiled with CONFIG_SLUB_DEBUG).
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Helge Deller [Sat, 21 Nov 2015 23:07:44 +0000 (00:07 +0100)]
parisc: Map kernel text and data on huge pages
Adjust the linker script and map_pages() to map kernel text and data on
physical 1MB huge/large pages.
Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Sat, 21 Nov 2015 23:07:06 +0000 (00:07 +0100)]
parisc: Add Huge Page and HUGETLBFS support
This patch adds huge page support to allow userspace to allocate huge
pages and to use hugetlbfs filesystem on 32- and 64-bit Linux kernels.
A later patch will add kernel support to map kernel text and data on
huge pages.
The only requirement is, that the kernel needs to be compiled for a
PA8X00 CPU (PA2.0 architecture). Older PA1.X CPUs do not support
variable page sizes. 64bit Kernels are compiled for PA2.0 by default.
Technically on parisc multiple physical huge pages may be needed to
emulate standard 2MB huge pages.
Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Fri, 20 Nov 2015 10:22:32 +0000 (11:22 +0100)]
parisc: Use long branch to do_syscall_trace_exit
Use the 22bit instead of the 17bit branch instruction on a 64bit kernel
to reach the do_syscall_trace_exit function from the gateway page.
A huge page enabled kernel may need the additional branch distance bits.
Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Fri, 20 Nov 2015 10:17:27 +0000 (11:17 +0100)]
parisc: Increase initial kernel mapping to 32MB on 64bit kernel
For the 64bit kernel the initially 16 MB kernel memory might become too
small if you build a kernel with many modules built-in and with kernel
text and data areas mapped on huge pages.
This patch increases the initial mapping to 32MB for 64bit kernels and
keeps 16MB for 32bit kernels.
Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Fri, 20 Nov 2015 09:50:01 +0000 (10:50 +0100)]
parisc: Initialize the fault vector earlier in the boot process.
A fault vector on parisc needs to be 2K aligned. Furthermore the
checksum of the fault vector needs to sum up to 0 which is being
calculated and written at runtime.
Up to now we aligned both PA20 and PA11 fault vectors on the same 4K
page in order to easily write the checksum after having mapped the
kernel read-only (by mapping this page only as read-write).
But when we want to map the kernel text and data on huge pages this
makes things harder.
So, simplify it by aligning both fault vectors on 2K boundries and write
the checksum before we map the page read-only.
Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Fri, 20 Nov 2015 14:46:52 +0000 (15:46 +0100)]
parisc: Add defines for Huge page support
Huge pages on parisc will have the same size as one pmd table, which
is on a 64bit kernel 2MB on a kernel with 4K kernel page sizes, and
on a 32bit kernel 4MB when used with 4K kernel pages.
Since parisc does not physically supports 2MB huge page sizes, emulate
it with two consecutive 1MB page sizes instead. Keeping the same huge
page size as one pmd will allow us to add transparent huge page support
later on.
Bit 21 in the pte flags was unused and will now be used to mark a page
as huge page (_PAGE_HPAGE_BIT).
Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Sun, 22 Nov 2015 11:14:14 +0000 (12:14 +0100)]
parisc: Drop unused MADV_xxxK_PAGES flags from asm/mman.h
Drop the MADV_xxK_PAGES flags, which were never used and were from a proposed
API which was never integrated into the generic Linux kernel code.
Cc: stable@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
Linus Torvalds [Sat, 21 Nov 2015 18:49:13 +0000 (10:49 -0800)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"A bunch of fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
slub: mark the dangling ifdef #else of CONFIG_SLUB_DEBUG
slub: avoid irqoff/on in bulk allocation
slub: create new ___slab_alloc function that can be called with irqs disabled
mm: fix up sparse warning in gfpflags_allow_blocking
ocfs2: fix umask ignored issue
PM/OPP: add entry in MAINTAINERS
kernel/panic.c: turn off locks debug before releasing console lock
kernel/signal.c: unexport sigsuspend()
kasan: fix kmemleak false-positive in kasan_module_alloc()
fat: fix fake_offset handling on error path
mm/hugetlbfs: fix bugs in fallocate hole punch of areas with holes
mm/page-writeback.c: initialize m_dirty to avoid compile warning
various: fix pci_set_dma_mask return value checking
mm: loosen MADV_NOHUGEPAGE to enable Qemu postcopy on s390
mm: vmalloc: don't remove inexistent guard hole in remove_vm_area()
tools/vm/page-types.c: support KPF_IDLE
ncpfs: don't allow negative timeouts
configfs: allow dynamic group creation
MAINTAINERS: add Moritz as reviewer for FPGA Manager Framework
slab.h: sprinkle __assume_aligned attributes
Linus Torvalds [Sat, 21 Nov 2015 18:26:24 +0000 (10:26 -0800)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"Two timer fixlets from Arnd:
- Use proper constant size in the FSL timer driver
- Prevent a build error for legacy platforms"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: Disallow drivers for ARCH_USES_GETTIMEOFFSET
clocksource/fsl: Avoid harmless 64-bit warnings
Linus Torvalds [Sat, 21 Nov 2015 18:19:15 +0000 (10:19 -0800)]
Merge branch 'irq-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"Three fixes for the ARM GIC interrupt controller from Marc addressing
various shortcomings versus boot initialization and suspend/resume"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic: Add save/restore of the active state
irqchip/gic: Clear enable bits before restoring them
irqchip/gic: Make sure all interrupts are deactivated at boot
Linus Torvalds [Sat, 21 Nov 2015 17:52:07 +0000 (09:52 -0800)]
Merge tag 'for-linus-
20151120' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
- MAINTAINERS updates for brcmnand driver
- Fix reboot hangs seen when multiple NAND flash chips are registered
with the same controller
- Fix build issues on jz4740 NAND driver; the error was introduced in
4.3, so I guess nobody really cared, but we might as well fix it
* tag 'for-linus-
20151120' of git://git.infradead.org/linux-mtd:
MAINTAINERS: brcmnand: Add co-maintainer for Broadcom SoCs
MAINTAINERS: brcmnand: Add Broadcom internal mailing-list
mtd: nand: fix shutdown/reboot for multi-chip systems
mtd: jz4740_nand: fix build on jz4740 after removing gpio.h
Jens Axboe [Sat, 21 Nov 2015 03:29:45 +0000 (20:29 -0700)]
blk-mq: fix calling unplug callbacks with preempt disabled
Liu reported that running certain parts of xfstests threw the
following error:
BUG: sleeping function called from invalid context at mm/page_alloc.c:3190
in_atomic(): 1, irqs_disabled(): 0, pid: 6, name: kworker/u16:0
3 locks held by kworker/u16:0/6:
#0: ("writeback"){++++.+}, at: [<
ffffffff8107f083>] process_one_work+0x173/0x730
#1: ((&(&wb->dwork)->work)){+.+.+.}, at: [<
ffffffff8107f083>] process_one_work+0x173/0x730
#2: (&type->s_umount_key#44){+++++.}, at: [<
ffffffff811e6805>] trylock_super+0x25/0x60
CPU: 5 PID: 6 Comm: kworker/u16:0 Tainted: G OE 4.3.0+ #3
Hardware name: Red Hat KVM, BIOS Bochs 01/01/2011
Workqueue: writeback wb_workfn (flush-btrfs-108)
ffffffff81a3abab ffff88042e282ba8 ffffffff8130191b ffffffff81a3abab
0000000000000c76 ffff88042e282ba8 ffff88042e27c180 ffff88042e282bd8
ffffffff8108ed95 ffff880400000004 0000000000000000 0000000000000c76
Call Trace:
[<
ffffffff8130191b>] dump_stack+0x4f/0x74
[<
ffffffff8108ed95>] ___might_sleep+0x185/0x240
[<
ffffffff8108eea2>] __might_sleep+0x52/0x90
[<
ffffffff811817e8>] __alloc_pages_nodemask+0x268/0x410
[<
ffffffff8109a43c>] ? sched_clock_local+0x1c/0x90
[<
ffffffff8109a6d1>] ? local_clock+0x21/0x40
[<
ffffffff810b9eb0>] ? __lock_release+0x420/0x510
[<
ffffffff810b534c>] ? __lock_acquired+0x16c/0x3c0
[<
ffffffff811ca265>] alloc_pages_current+0xc5/0x210
[<
ffffffffa0577105>] ? rbio_is_full+0x55/0x70 [btrfs]
[<
ffffffff810b7ed8>] ? mark_held_locks+0x78/0xa0
[<
ffffffff81666d50>] ? _raw_spin_unlock_irqrestore+0x40/0x60
[<
ffffffffa0578c0a>] full_stripe_write+0x5a/0xc0 [btrfs]
[<
ffffffffa0578ca9>] __raid56_parity_write+0x39/0x60 [btrfs]
[<
ffffffffa0578deb>] run_plug+0x11b/0x140 [btrfs]
[<
ffffffffa0578e33>] btrfs_raid_unplug+0x23/0x70 [btrfs]
[<
ffffffff812d36c2>] blk_flush_plug_list+0x82/0x1f0
[<
ffffffff812e0349>] blk_sq_make_request+0x1f9/0x740
[<
ffffffff812ceba2>] ? generic_make_request_checks+0x222/0x7c0
[<
ffffffff812cf264>] ? blk_queue_enter+0x124/0x310
[<
ffffffff812cf1d2>] ? blk_queue_enter+0x92/0x310
[<
ffffffff812d0ae2>] generic_make_request+0x172/0x2c0
[<
ffffffff812d0ad4>] ? generic_make_request+0x164/0x2c0
[<
ffffffff812d0ca0>] submit_bio+0x70/0x140
[<
ffffffffa0577b29>] ? rbio_add_io_page+0x99/0x150 [btrfs]
[<
ffffffffa0578a89>] finish_rmw+0x4d9/0x600 [btrfs]
[<
ffffffffa0578c4c>] full_stripe_write+0x9c/0xc0 [btrfs]
[<
ffffffffa057ab7f>] raid56_parity_write+0xef/0x160 [btrfs]
[<
ffffffffa052bd83>] btrfs_map_bio+0xe3/0x2d0 [btrfs]
[<
ffffffffa04fbd6d>] btrfs_submit_bio_hook+0x8d/0x1d0 [btrfs]
[<
ffffffffa05173c4>] submit_one_bio+0x74/0xb0 [btrfs]
[<
ffffffffa0517f55>] submit_extent_page+0xe5/0x1c0 [btrfs]
[<
ffffffffa0519b18>] __extent_writepage_io+0x408/0x4c0 [btrfs]
[<
ffffffffa05179c0>] ? alloc_dummy_extent_buffer+0x140/0x140 [btrfs]
[<
ffffffffa051dc88>] __extent_writepage+0x218/0x3a0 [btrfs]
[<
ffffffff810b7ed8>] ? mark_held_locks+0x78/0xa0
[<
ffffffffa051e2c9>] extent_write_cache_pages.clone.0+0x2f9/0x400 [btrfs]
[<
ffffffffa051e422>] extent_writepages+0x52/0x70 [btrfs]
[<
ffffffffa05001f0>] ? btrfs_set_inode_index+0x70/0x70 [btrfs]
[<
ffffffffa04fcc17>] btrfs_writepages+0x27/0x30 [btrfs]
[<
ffffffff81184df3>] do_writepages+0x23/0x40
[<
ffffffff81212229>] __writeback_single_inode+0x89/0x4d0
[<
ffffffff81212a60>] ? writeback_sb_inodes+0x260/0x480
[<
ffffffff81212a60>] ? writeback_sb_inodes+0x260/0x480
[<
ffffffff8121295f>] ? writeback_sb_inodes+0x15f/0x480
[<
ffffffff81212ad2>] writeback_sb_inodes+0x2d2/0x480
[<
ffffffff810b1397>] ? down_read_trylock+0x57/0x60
[<
ffffffff811e6805>] ? trylock_super+0x25/0x60
[<
ffffffff810d629f>] ? rcu_read_lock_sched_held+0x4f/0x90
[<
ffffffff81212d0c>] __writeback_inodes_wb+0x8c/0xc0
[<
ffffffff812130b5>] wb_writeback+0x2b5/0x500
[<
ffffffff810b7ed8>] ? mark_held_locks+0x78/0xa0
[<
ffffffff810660a8>] ? __local_bh_enable_ip+0x68/0xc0
[<
ffffffff81213362>] ? wb_do_writeback+0x62/0x310
[<
ffffffff812133c1>] wb_do_writeback+0xc1/0x310
[<
ffffffff8107c3d9>] ? set_worker_desc+0x79/0x90
[<
ffffffff81213842>] wb_workfn+0x92/0x330
[<
ffffffff8107f133>] process_one_work+0x223/0x730
[<
ffffffff8107f083>] ? process_one_work+0x173/0x730
[<
ffffffff8108035f>] ? worker_thread+0x18f/0x430
[<
ffffffff810802ed>] worker_thread+0x11d/0x430
[<
ffffffff810801d0>] ? maybe_create_worker+0xf0/0xf0
[<
ffffffff810801d0>] ? maybe_create_worker+0xf0/0xf0
[<
ffffffff810858df>] kthread+0xef/0x110
[<
ffffffff8108f74e>] ? schedule_tail+0x1e/0xd0
[<
ffffffff810857f0>] ? __init_kthread_worker+0x70/0x70
[<
ffffffff816673bf>] ret_from_fork+0x3f/0x70
[<
ffffffff810857f0>] ? __init_kthread_worker+0x70/0x70
The issue is that we've got the software context pinned while
calling blk_flush_plug_list(), which flushes callbacks that
are allowed to sleep. btrfs and raid has such callbacks.
Flip the checks around a bit, so we can enable preempt a bit
earlier and flush plugs without having preempt disabled.
This only affects blk-mq driven devices, and only those that
register a single queue.
Reported-by: Liu Bo <bo.li.liu@oracle.com>
Tested-by: Liu Bo <bo.li.liu@oracle.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
Arnd Bergmann [Mon, 16 Nov 2015 15:48:09 +0000 (16:48 +0100)]
serial: export fsl8250_handle_irq
fsl8250_handle_irq is now used by the of_serial driver, and that fails
if it is a loadable module:
ERROR: "fsl8250_handle_irq" [drivers/tty/serial/of_serial.ko] undefined!
This exports the symbol to avoid randconfig errors.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes:
d43b54d269d2 ("serial: Enable Freescale 16550 workaround on arm")
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heikki Krogerus [Thu, 12 Nov 2015 13:21:23 +0000 (15:21 +0200)]
serial: 8250_mid: Add missing dependency
8250_mid uses rational_best_approximation() function, so the
driver needs to select CONFIG_RATIONAL option.
This fixes build error when CONFIG_RATIONAL is not enabled:
drivers/built-in.o: In function `mid8250_set_termios':
8250_mid.c:(.text+0x10169a): undefined reference to `rational_best_approximation'
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Sun, 8 Nov 2015 13:52:31 +0000 (08:52 -0500)]
tty: audit: Fix audit source
The data to audit/record is in the 'from' buffer (ie., the input
read buffer).
Fixes:
72586c6061ab ("n_tty: Fix auditing support for cannonical mode")
Cc: stable <stable@vger.kernel.org> # 4.1+
Cc: Miloslav Trmač <mitr@redhat.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Laura Abbott <labbott@fedoraproject.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guenter Roeck [Mon, 2 Nov 2015 02:32:56 +0000 (18:32 -0800)]
serial: etraxfs-uart: Fix crash
Since commit
7d8c70d8048c ("serial: mctrl-gpio: rename init function"),
crisv32 either do not build or crash as follows.
Unable to handle kernel NULL pointer dereference
Linux 4.3.0-rc7-next-
20151101 #1 Sun Nov 1 11:41:28 PST 2015
...
Call Trace: [<
c0004a0e>] show_stack+0x0/0x9e
[<
c004c0c0>] printk+0x0/0x2c
[<
c00059d4>] show_registers+0x14a/0x1c2
[<
c004c0c0>] printk+0x0/0x2c
[<
c0004b52>] die_if_kernel+0x7c/0x9e
[<
c0005346>] do_page_fault+0x32e/0x3e6
[<
c01dc59c>] of_get_property+0x0/0x2c
[<
c01e0558>] of_irq_parse_raw+0x12a/0x376
[<
c01dc59c>] of_get_property+0x0/0x2c
[<
c0053aca>] get_page_from_freelist+0x73e/0x856
[<
c01dc59c>] of_get_property+0x0/0x2c
[<
c0008912>] d_mmu_refill+0x10a/0x112
[<
c01b488c>] devm_kmalloc+0x40/0x56
[<
c01b47d0>] add_dr+0xc/0x1c
[<
c01b4800>] devm_add_action+0x2/0x4e
[<
c01abdbc>] mctrl_gpio_init_noauto+0x1c/0x76
[<
c01abf9e>] mctrl_gpio_init+0x22/0x110
The function call in the etraxfs-uart driver was not renamed,
possibly due to interference with commit
7b9c5162c182 ("serial:
etraxfs-uart: use mctrl_gpio helpers for handling modem signals").
Fixes:
7d8c70d8048c ("serial: mctrl-gpio: rename init function")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Niklas Cassel <nks@flawful.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Tue, 20 Oct 2015 13:55:21 +0000 (09:55 -0400)]
serial: fsl_lpuart: Fix earlycon support
Earlycon support for Freescale lpuart should only be enabled when
console support is enabled.
Fixes:
1d59b382f1c4 ("serial: fsl_lpuart: add earlycon support")
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simon Arlott [Sun, 15 Nov 2015 16:14:32 +0000 (16:14 +0000)]
bcm63xx_uart: Use the device name when registering an interrupt
Use the device name when registering an interrupt so that multiple
ports don't all have the same interrupt name.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Sun, 8 Nov 2015 12:53:06 +0000 (07:53 -0500)]
tty: Fix direct use of tty buffer work
Recent abstraction of tty buffer work introduced api to manage
tty input kworker; use it.
Fixes:
e176058f0de5 ("tty: Abstract tty buffer work")
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Wed, 11 Nov 2015 13:03:54 +0000 (08:03 -0500)]
tty: Fix tty_send_xchar() lock order inversion
The correct lock order is atomic_write_lock => termios_rwsem, as
established by tty_write() => n_tty_write().
Fixes:
c274f6ef1c666 ("tty: Hold termios_rwsem for tcflow(TCIxxx)")
Reported-and-Tested-by: Dmitry Vyukov <dvyukov@google.com>
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jesper Dangaard Brouer [Fri, 20 Nov 2015 23:57:41 +0000 (15:57 -0800)]
slub: mark the dangling ifdef #else of CONFIG_SLUB_DEBUG
The #ifdef of CONFIG_SLUB_DEBUG is located very far from the associated
#else. For readability mark it with a comment.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christoph Lameter [Fri, 20 Nov 2015 23:57:38 +0000 (15:57 -0800)]
slub: avoid irqoff/on in bulk allocation
Use the new function that can do allocation while interrupts are disabled.
Avoids irq on/off sequences.
Signed-off-by: Christoph Lameter <cl@linux.com>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / platform / kernel / linux-rpi.git / log