Marek Vasut [Wed, 6 Mar 2019 19:07:55 +0000 (20:07 +0100)]
ARM: socfpga: Fix A10 SoCDK Kconfig
The Kconfig checked for SoCFPGA Arria10 as a platform, instead of
checking for specific board configuration, which works with one
single platform in tree, but not with multiple. Fix it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Marek Vasut [Tue, 8 May 2018 16:44:43 +0000 (18:44 +0200)]
ARM: socfpga: Fix Arria10 SPI and NAND U-Boot offset
The SPL size on Gen5 is 4*64kiB, but on A10 it is 4*256kiB.
Handle the difference.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Marek Vasut [Tue, 8 May 2018 16:44:00 +0000 (18:44 +0200)]
ARM: socfpga: Drop CONFIG_SYS_NAND_BAD_BLOCK_POS
This is not used anywhere, so drop it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Marek Vasut [Tue, 8 May 2018 18:32:01 +0000 (20:32 +0200)]
ARM: socfpga: Disable D cache in SPL
The bootrom seems to leave the D-cache in messed up state, make sure
the SPL disables it so it can not interfere with operation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Marek Vasut [Wed, 6 Mar 2019 16:18:22 +0000 (17:18 +0100)]
ddr: socfpga: Fix newline in debug print on A10
The debug print is missing a newline, add it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Marek Vasut [Tue, 5 Mar 2019 17:37:02 +0000 (18:37 +0100)]
ddr: socfpga: Fix IO in Arria10 DDR driver
The Altera Arria10 DDR driver was using constants in a few places
instead of reading registers associated with those constants, fix
this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Dinh Nguyen [Sun, 3 Mar 2019 17:02:10 +0000 (11:02 -0600)]
ARM: socfpga: fix data and tag latency values for pl310 cache controller
The values for the data and tag latency settings on the PL310 caches
controller is an (n-1). For example, the "arm,tag-latency" is specified
as <1 1 1>, so the values that should be written to register should be
0x000. And for the "arm,data-latency" specified as <2 1 1>, the register
value should be 0x010.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Tom Rini [Fri, 8 Mar 2019 23:04:13 +0000 (18:04 -0500)]
Merge branch '2019-03-08-master-imports'
- Assorted minor fixes:
- ARM: qemu-arm: enable USB boot in distro boot with UEFI
- image: fdt: handle coalesced reserve region
- cmd: thordown: Fix spelling of download.
- fdt: Fix FIT header verification in mkimage and conduct same checks
as bootm
- test: Update test-imagetools.sh to match new syntax
AKASHI Takahiro [Fri, 14 Dec 2018 09:53:22 +0000 (18:53 +0900)]
ARM: qemu-arm: enable USB boot in distro boot with UEFI
With this patch which adds a removable USB mass storage to a list
of bootable devices, USB boot is supported in distro boot if UEFI is
configured.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Patrick Delaunay [Wed, 6 Mar 2019 13:23:52 +0000 (14:23 +0100)]
image: fdt: handle coalesced reserve region
Handle in boot_fdt_reserve_region
any return value > 0 of lmb_reserve() function;
it occurs when coalesced region are found:
adjacent reserved region are merged.
This patch avoid the error trace:
ERROR: reserving fdt memory region failed..
when reserved region are merged (return value = 1).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Vagrant Cascadian [Wed, 6 Mar 2019 06:52:14 +0000 (22:52 -0800)]
cmd: thordown: Fix spelling of download.
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Jordan Hand [Tue, 5 Mar 2019 22:47:56 +0000 (14:47 -0800)]
fdt: Fix FIT header verification in mkimage and conduct same checks as bootm
FIT header verification in mkimage was treating a return code as a boolean,
which meant that failures in validating the fit were seen as successes.
Additionally, mkimage was checking all formats to find a header which
passes validation, rather than using the image type specified to
mkimage.
checkpatch.pl checks for lines ending with '(' and alignment matching
open parentheses are ignored to keep with existing coding style.
Signed-off-by: Jordan Hand <jorhand@microsoft.com>
Martyn Welch [Thu, 14 Feb 2019 13:11:35 +0000 (13:11 +0000)]
test: Update test-imagetools.sh to match new syntax
The syntax of dumpimage was simplified in commit
12b831879a76 ("tools:
dumpimage: Simplify arguments"), but the test
(test/image/test-imagetools.sh) was not updated and is now failing.
Update the test to use the new syntax.
Reported-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Tom Rini [Fri, 8 Mar 2019 12:26:29 +0000 (07:26 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-i2c
This pull request contains bugfixes for rcar_i2c, rcar_ii2c and
i2c_cdns driver.
Also the commit "i2c: rcar_i2c: Add Gen3 SoC support" from Marek
is a bugfix for arm64 builds, as discussed with Marek on list.
Ismael Luceno Cortes [Thu, 7 Mar 2019 18:00:55 +0000 (18:00 +0000)]
i2c: rcar_i2c: Move FSDA check to rcar_i2c_recover
Cosmetic change. Any call to the recover function would need to do the
same check afterwards, so it's sensible to make it part of the function.
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
Ismael Luceno Cortes [Thu, 7 Mar 2019 18:00:54 +0000 (18:00 +0000)]
i2c: rcar_i2c: Set the slave address from rcar_i2c_xfer
It needs to be done for both reads and writes, so do it at rcar_i2c_xfer
to avoid duplication.
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Ismael Luceno Cortes [Thu, 7 Mar 2019 18:00:53 +0000 (18:00 +0000)]
i2c: rcar_i2c: Don't mask errors with EREMOTEIO at rcar_i2c_xfer
Fix rcar_i2c_xfer return value, previously it was always returning
-EREMOTEIO when dealing with errors from calls to the read/write
functions.
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Ismael Luceno Cortes [Thu, 7 Mar 2019 18:00:52 +0000 (18:00 +0000)]
i2c: rcar_i2c: Fix sending of slave addresses
Do the reset before clearing the MSR, otherwise it may result in a read
or write operation instead if the start condition is repeated.
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Ismael Luceno Cortes [Thu, 7 Mar 2019 18:00:51 +0000 (18:00 +0000)]
i2c: rcar_i2c: Add comments about registers & values
Document the meaning of macros related to registers and values to be
written to them.
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Ismael Luceno Cortes [Thu, 7 Mar 2019 18:00:49 +0000 (18:00 +0000)]
i2c: rcar_i2c: Setup SCL/SDA delay at rcar_i2c_set_speed
Setting up the delay only needs to be done once; move it to
rcar_i2c_set_speed so it's done at initialization time.
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Siva Durga Prasad Paladugu [Thu, 7 Mar 2019 10:52:49 +0000 (11:52 +0100)]
i2c: i2c_cdns: Add support for handling arbitration lost
This patch adds support for handling arbitration lost
in case of multi master mode. When an arbitration lost
is detected, it retries for 10 times before failing.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Siva Durga Prasad Paladugu [Thu, 7 Mar 2019 10:52:48 +0000 (11:52 +0100)]
i2c: i2c_cdns: Fix clearing of all interrupts
The arbitration lost interrupt was not getting cleared
while clearing interrupts. This patch fixes this by adding
arbitration lost interrupt as well during clear. This patch
also removes hardcoded value and defined a macro for it.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Marek Vasut [Sat, 2 Mar 2019 16:17:11 +0000 (17:17 +0100)]
i2c: rcar_i2c: Add Gen3 SoC support
Add support for R-Car Gen3 SoCs into the driver, which encompases
the Gen3 SoC extra timing register handling and 64bit build fixes.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Marek Vasut [Thu, 7 Mar 2019 02:41:08 +0000 (03:41 +0100)]
i2c: rcar_iic: Read ICSR only once
Read ICSR only once to avoid missing interrupts. This happens on R8A7791
Porter during reset, when reading the PMIC register 0x13, which may fail
sometimes because of the missed DTE interrupt.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tom Rini [Thu, 7 Mar 2019 01:25:09 +0000 (20:25 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-spi
- dw spi include file fix
- Allwinner A31 spi, been in ML in many releases.
Tom Rini [Tue, 5 Mar 2019 13:51:48 +0000 (08:51 -0500)]
Merge tag 'efi-2019-04-rc4' of https://github.com/xypron2/u-boot
Pull request for the UEFI subsystem for v2019.04-rc4
This pull request contains only bug fixes.
The most notable bug fixed was writing to random memory addresses when
trying to add a HII package of a yet unsupported package type.
Tom Rini [Tue, 5 Mar 2019 02:46:24 +0000 (21:46 -0500)]
Prepare v2019.04-rc4
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Mon, 4 Mar 2019 21:35:40 +0000 (16:35 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-sh
- Assorted PFC fixes
Tom Rini [Mon, 4 Mar 2019 18:06:22 +0000 (13:06 -0500)]
Merge tag 'u-boot-atmel-2019.04-a' of git://git.denx.de/u-boot-atmel
First set of u-boot-atmel fixes for 2019.04 cycle
Tom Rini [Mon, 4 Mar 2019 18:05:53 +0000 (13:05 -0500)]
Merge git://git.denx.de/u-boot-fsl-qoriq
- Enable DHCP as boot-source in distro boot for NXP layerscape
platforms
- fix register layout for SEC on Layerscape architectures
- fixes related to DPAA2 ethernet
Jagan Teki [Wed, 27 Feb 2019 14:32:13 +0000 (20:02 +0530)]
spi: Rename sun4i_spi.c into spi-sunxi.c
Now the same SPI controller driver is reusable in all Allwinner
SoC variants, so rename the existing sun4i_spi.c into spi-sunxi.c
which eventually look like a common sunxi driver.
Also update the function, variable, structure names in driver from
sun4i into sunxi.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Wed, 27 Feb 2019 14:32:12 +0000 (20:02 +0530)]
spi: sun4i: Driver cleanup
- drop unused macros.
- use base instead of base_addr, for better code readability
- move .probe and .ofdata_to_platdata functions in required
places to add platdata support in future.
- use sentinel sun4i_spi_ids.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Wed, 27 Feb 2019 14:32:11 +0000 (20:02 +0530)]
spi: sun4: Add A31 spi controller support
The usual SPI transmission protocol in Allwinner A10 and A31
controllers share similar context with minimal changes in register
offsets along with few additional register bits on A31.
So, add A31 spi controller support in existing sun4i_spi with A31
specific register offsets and bits.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Wed, 27 Feb 2019 14:32:10 +0000 (20:02 +0530)]
spi: sun4i: Add CLK support
Add CLK support to enable AHB and MOD SPI clocks on sun4i_spi driver.
Clock disablement could be done while releasing the bus transfer, but
the existing code doesn't disable the clocks it only taken care of clock
enablement globally in probe.
So to make a proper clock handling, the clocks should enable it in claim
and disable it in release.
This patch would also do that change, by enable and disable clock in
proper order.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Jagan Teki [Wed, 27 Feb 2019 14:32:09 +0000 (20:02 +0530)]
spi: sun4i: Support fifo_depth via drvdata
Support fifo_depth via drvdata instead of macro definition, this would
eventually reduce another macro definition for new SPI controller fifo
depth support addition.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Jagan Teki [Wed, 27 Feb 2019 14:32:08 +0000 (20:02 +0530)]
spi: sun4i: Access registers and bits via enum offsets
Allwinner support two different SPI controllers one for A10 and
another for A31 with minimal changes in register offsets and
respective register bits, but the logic for accessing the SPI
master via SPI slave remains nearly similar.
Add enum offsets for register set and register bits, so-that
it can access both classes of SPI controllers.
Assign same control register for global, transfer and fifo control
registers to make the same code compatible with A31 SPI controller.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Stefan Mavrodiev <stefan@olimex.com> # A20-SOM204
Jagan Teki [Wed, 27 Feb 2019 14:32:07 +0000 (20:02 +0530)]
spi: sun4i: Simplify reg writes using set/clrbits_le32
Update the existing register writes using setbits_le32 and
clrbits_le32 in required places.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Wed, 27 Feb 2019 14:32:06 +0000 (20:02 +0530)]
clk: sunxi: Implement SPI clocks, resets
- Implement SPI AHB, MOD clocks via ccu_clk_gate for all
supported Allwinner SoCs
- Implement SPI resets via ccu_reset for all supported
Allwinner SoCs.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Jagan Teki [Wed, 27 Feb 2019 14:32:05 +0000 (20:02 +0530)]
spi: sun4i: Poll for rxfifo to be filled up
To drain rx fifo the fifo need to poll for how much data has
been filled up in rx fifo.
To achieve this, the current code is using wait_for_bit logic
on control register with exchange burst mode mask, which is not
a proper way of waiting for fifo filled up.
So, add code for polling rxfifo to be filled up using fifo
status register.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Horatiu.Vultur@microchip.com [Mon, 25 Feb 2019 10:59:54 +0000 (10:59 +0000)]
spi: designware: Change include order
With current order of include files, the file designware_spi.c
can't see that the struct global_data has the member
board_type when CONFIG_BOARD_TYPES is defined. By not seeing this
then all the members are shifted in the struct global_data.
So when the driver is trying to read from device tree blob, it
would pass the wrong address to the function 'fdtdev_get_int'.
This will make to use the default frequency 500000.
The fix consists of changing the order of include files in
designware_spi.c to include first common.h file.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Eugen Hristev [Fri, 8 Feb 2019 08:57:01 +0000 (10:57 +0200)]
configs: at91: remove SPL_GENERATE_ATMEL_PMECC_HEADER from non-nand configs
SPL_GENERATE_ATMEL_PMECC_HEADER will generate a header for the SPL for NAND
information. The initial stage 1 bootloader will use this header in case the
NAND flash doesn't support commands to retrieve sector size, etc.
However this header is bad for different boot media, like MMC or SPI.
In case SD_BOOT or SPI_BOOT is used, remove the config for this.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Alexander Dahl [Wed, 6 Feb 2019 14:19:41 +0000 (15:19 +0100)]
configs: sama5d27_som1_ek: Activate misc init for uSD variant
This was already set for 'sama5d27_som1_ek_mmc_defconfig' (first SD
card, full size). Without this option set, the MAC address is not read
from the I²C EEPROM at boot, and remains unset:
U-Boot 2019.01 (Jan 01 2019 - 00:00:00 +0000)
CPU: SAMA5D27 1G bits DDR2 SDRAM
Crystal frequency: 24 MHz
CPU clock : 492 MHz
Master clock : 164 MHz
DRAM: 128 MiB
MMC: sdio-host@
a0000000: 0, sdio-host@
b0000000: 1
Loading Environment from FAT... OK
In: serial
Out: serial
Err: serial
Net:
Error: ethernet@
f8008000 address not set.
eth-1: ethernet@
f8008000
Hit any key to stop autoboot: 0
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Hiroyuki Yokoyama [Wed, 13 Feb 2019 05:23:46 +0000 (14:23 +0900)]
pinctrl: renesas: r8a77990: Reivse USB ID pin name
Since the datasheet Rev.1.00 has an error about the USB ID pin name,
this patch revises it.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Hiroyuki Yokoyama [Wed, 13 Feb 2019 03:41:04 +0000 (12:41 +0900)]
pinctrl: renesas: r8a77990: Fix MOD_SEL0 bit3 when using TX0
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.50,
the MOD_SEL0 bit3 is set to 0 when TX0_A pin function is selected,
and the MOD_SEL0 bit3 is set to 1 when TX0_B pin function is
selected.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Hiroyuki Yokoyama [Wed, 13 Feb 2019 03:35:53 +0000 (12:35 +0900)]
pinctrl: renesas: r8a77990: Fix MOD_SEL0 bit16 when using NFALE and NFRB_N
According to the R-Car Gen3 Hardware Manual Rev.1.50, the MOD_SEL0
bit16 is set to 0 when NFALE_A and NFRB_N_A pin functions are
selected.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Hiroyuki Yokoyama [Wed, 13 Feb 2019 03:18:28 +0000 (12:18 +0900)]
pinctrl: renesas: r8a77990: Fix MOD_SEL0 bit2 when using RX2,TX2 and SCK2
According to the R-Car Gen3 Hardware Manual Rev 1.50, the MOD_SEL0
bit2 is set when RX2_{A,B}, TX2_{A,B} and SCK2_A pin functions are
selected.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Hiroyuki Yokoyama [Wed, 13 Feb 2019 01:37:48 +0000 (10:37 +0900)]
pinctrl: renesas: r8a77990: Fix rename RTSx_N_TANS_x to RTSx_N_x
This patch fixes the allocation name "RTSx_N_TANS_x" of IPSR /
MOD_SEL0/1 of r8a77990 to "RTSx_N_x". This information was
confirmed in the R-Car Gen3 Hardware Manual Rev.1.50.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Hiroyuki Yokoyama [Wed, 13 Feb 2019 01:22:26 +0000 (10:22 +0900)]
pinctrl: renesas: Fix r8a779{6,65} rename sel_ndfc to sel_ndf
This patch fixes the allocation name "sel_ndfc" of MOD_SEL2[22]
of r8a7796 / r8a77965 to "sel_ndf". This information was confirmed
in the R-Car Gen3 Hardware Manual Rev.1.50.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Hiroyuki Yokoyama [Wed, 13 Feb 2019 01:06:22 +0000 (10:06 +0900)]
pinctrl: renesas: Remove r8a779{5,6,65} CC5_OSCOUT of IP17
This patch removes CC5_OSCOUT assignment of IP17[3:0] of r8a7795
/ r8a7796 / r8a77965. This information was confirmed in the R-Car
Gen3 Hardware Manual Rev.1.50.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Hiroyuki Yokoyama [Tue, 12 Feb 2019 11:50:01 +0000 (20:50 +0900)]
pinctrl: renesas: Fix r8a779{5,6,65} rename sel_adg_ to sel_adg
This patch fixes to the correct names, and "_" is not include after
"adg" for r8a7795/r8a7796/r8a77965. This information was confirmed
in the R-Car Gen3 Hardware Manual Rev.1.50.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Hiroyuki Yokoyama [Tue, 12 Feb 2019 10:09:13 +0000 (19:09 +0900)]
pinctrl: renesas: Fix r8a779{5,6,65} assign to GP7_03/02 of GPSR7
This patch is change the bit assignment of "HDMI1_CEC" to "GP7_03",
and "HDMI0_CEC" to "GP7_02". This information was confirmed in the
R-Car Gen3 Hardware Manual Rev.1.50.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Yunfeng Ding [Tue, 19 Feb 2019 06:44:04 +0000 (14:44 +0800)]
board: Enable DHCP distro boot for LS1012a, LS1021a
Enable DHCP distro boot for Layerscape LS1012A and LS1021A.
Signed-off-by: Yunfeng Ding <yunfeng.ding@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Laurentiu Tudor [Tue, 26 Feb 2019 11:18:34 +0000 (13:18 +0200)]
armv8: fsl-layerscape: avoid DT fixup warning
sec_firmware reserves JR3 for it's own usage and deletes the JR3 node
from the device tree. This causes this warning to be issued when doing
the device tree fixup:
WARNING could not find node fsl,sec-v4.0-job-ring: FDT_ERR_NOTFOUND.
Fix it by excluding the device tree fixup for the JR reserved by
sec_firmware.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Laurentiu Tudor [Tue, 26 Feb 2019 11:18:33 +0000 (13:18 +0200)]
armv8: fsl-layerscape: fix SEC QI ICID setup
The SEC QI ICID setup in the QIIC_LS register is actually an offset
that is being added to the ICID coming from the qman portal. Setting
it with a non-zero value breaks SMMU setup as the resulting ICID is
not known. On top of that, the SEC QI ICID must match the qman portal
ICIDs in order to share the isolation context.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Laurentiu Tudor [Tue, 26 Feb 2019 11:18:32 +0000 (13:18 +0200)]
fsl_sec: fix register layout on Layerscape architectures
On Layerscape architectures the SEC memory map is 1MB and the
register blocks contained in it are 64KB aligned, not 4KB as
the ccsr_sec structure currently assumes. Fix the layout of
the structure for these architectures.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Prabhakar Kushwaha [Sun, 3 Mar 2019 16:27:54 +0000 (21:57 +0530)]
board: ls1046qds: Enable PPA for secure boot
Re-organize defconfig and enabled PPA for secure boot
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Rajesh Bhagat [Fri, 1 Feb 2019 05:22:01 +0000 (05:22 +0000)]
configs: fsl: move DDR specific defines to Kconfig
Moves below DDR specific defines to Kconfig:
CONFIG_FSL_DDR_BIST
CONFIG_FSL_DDR_FIRST_SLOT_QUAD_CAPABLE
CONFIG_FSL_DDR_INTERACTIVE
CONFIG_FSL_DDR_SYNC_REFRESH
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Mian Yousaf Kaukab [Tue, 29 Jan 2019 15:38:41 +0000 (16:38 +0100)]
board: ls1043a: use default scan_dev_for_boot
Default environment variable is more complete. Also scans for efi
binaries for example.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Mian Yousaf Kaukab [Tue, 29 Jan 2019 15:38:40 +0000 (16:38 +0100)]
board: ls1043a: enable dhcp boot
dhcp boot is a useful feature and works out-of-the-box on these
platforms. Enable it as a boot source.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Mian Yousaf Kaukab [Tue, 29 Jan 2019 15:38:39 +0000 (16:38 +0100)]
board: ls1043a: enable EFI_LOADER_BOUNCE_BUFFER
EFI applications need bounce buffers to work properly on these
platforms.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Mian Yousaf Kaukab [Tue, 29 Jan 2019 15:38:38 +0000 (16:38 +0100)]
board: ls1046a: use default scan_dev_for_boot
Default environment variable is more complete. Also scans for efi
binaries for example.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Mian Yousaf Kaukab [Tue, 29 Jan 2019 15:38:37 +0000 (16:38 +0100)]
board: ls1046a: enable dhcp boot
dhcp boot is a useful feature and works out-of-the-box on these
platforms. Enable it as a boot source.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Mian Yousaf Kaukab [Tue, 29 Jan 2019 15:38:36 +0000 (16:38 +0100)]
board: ls1046a: enable EFI_LOADER_BOUNCE_BUFFER
EFI applications need bounce buffers to work properly on these
platforms.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Mian Yousaf Kaukab [Tue, 29 Jan 2019 15:38:35 +0000 (16:38 +0100)]
board: ls2080ardb: use default scan_dev_for_boot
Default environment variable is more complete. Also scans for efi
binaries for example.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Mian Yousaf Kaukab [Tue, 29 Jan 2019 15:38:34 +0000 (16:38 +0100)]
Revert "ls2080ardb: remove dhcp function from env as boot source"
dhcp boot is a useful feature and works out-of-the-box for ls2088a
platforms. Moreover, no solid reason is given for disabling it.
Revert the patch to re-enable it.
This reverts commit
aea5cd75e63c20de4c00ce24a93eeee8542f923e.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Mian Yousaf Kaukab [Tue, 29 Jan 2019 15:38:33 +0000 (16:38 +0100)]
board: ls1088ardb: use default scan_dev_for_boot
Default environment variable is more complete. Also scans for efi
binaries for example.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Mian Yousaf Kaukab [Tue, 29 Jan 2019 15:38:32 +0000 (16:38 +0100)]
Revert "ls1088a: remove dhcp function from u-boot env as boot source"
dhcp boot is a useful feature and works out-of-the-box for ls1088a
platforms. Moreover, no solid reason is given for disabling it.
Revert the patch to re-enable it.
This reverts commit
863e42e8b1f9e97d87919e20e34a7b98089f7522.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Mian Yousaf Kaukab [Tue, 29 Jan 2019 15:38:31 +0000 (16:38 +0100)]
board: ls1088a: fix fsl-mc search path
Path for fsl-mc node in kernel device-tree is /soc/fsl-mc whereas
in u-boot it is /fsl-mc.
Fix the incorrect search path to fix following error:
fdt_fixup_board_enet: ERROR: fsl-mc node not found in device tree
(error -1)
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Mian Yousaf Kaukab [Tue, 29 Jan 2019 15:38:30 +0000 (16:38 +0100)]
board: ls1088a: fix dppa exit when using efi boot
Same issue for ls2080a was fixed by following patch:
b7b8410a8f ls2080: Exit dpaa only right before exiting U-Boot
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Tom Rini [Sun, 3 Mar 2019 13:00:30 +0000 (08:00 -0500)]
Merge git://git.denx.de/u-boot-mpc85xx
Heinrich Schuchardt [Thu, 28 Feb 2019 22:56:35 +0000 (23:56 +0100)]
efi_loader: HII protocols: debug messages
When package types are not supported by our implementation of the HII
database protocol supported error messages are displayed.
Essentially the output is only needed for debugging. By using EFI_PRINT()
the messages are only written for in debug mode and with correct
indentation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Thu, 28 Feb 2019 19:41:58 +0000 (20:41 +0100)]
efi_loader: error handling for `efidebug boot add`
In `efidebug boot add iPXE scsi 0:1 snp-arm64.efi --foo` a parameter is
missing. Hence the command should not silently return as if everything were
ok but should display the usage info.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Alexander Graf <agraf@csgraf.de>
Heinrich Schuchardt [Thu, 28 Feb 2019 22:07:00 +0000 (23:07 +0100)]
efi_loader: HII protocols: fix new_package_list()
In new_package_list() we call new_packagelist() to create a new package
list. Next we try to add the packages which fails for form packages. Due
to this error we call free_packagelist(). Now in free_packagelist()
list_del() is called for an uninitialized field hii->link. This leads to
changing random memory addresses.
To solve the problem move the initialization of hii->link to
new_packagelist().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Heinrich Schuchardt [Sat, 23 Feb 2019 10:20:23 +0000 (11:20 +0100)]
efi_loader: do not add \ in efi_fs_from_name()
In the `efidebug boot add` command we do not want an unsolicited leading
backslash added to the file name.
There is no good reason to mark a loaded file with a backslash as absolute.
Anyway when reading files the file name will be interpreted as relative to
root directory of the device.
So let's get rid of this backslash.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Peng Ma [Thu, 21 Feb 2019 02:18:27 +0000 (10:18 +0800)]
powerpc: t104xrdb: Add support of MTA9ADF1G72AZ DDR
T1040RDB has been upgraded to support new DDR ie. MTA9ADF1G72AZ-3G2, 8GB.
So adding support of new DDR part by updating board_specific_parameters
udimm0.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Heinrich Schuchardt [Sun, 20 Jan 2019 08:11:07 +0000 (09:11 +0100)]
powerpc: enabled building with CONFIG_DM=y
Moving to the driver model requires CONFIG_DM to be enabled. Currently
several boards like kmeter1_defconfig produce a build error when CONFIG_DM
is enabled:
In file included from include/common.h:35,
from ./arch/powerpc/include/asm/fsl_lbc.h:10,
from include/mpc83xx.h:10,
from ./arch/powerpc/include/asm/ppc.h:27,
from ./arch/powerpc/include/asm/u-boot.h:18,
from include/dm/of.h:10,
from include/dm/ofnode.h:12,
from include/dm/device.h:13,
from include/linux/mtd/mtd.h:26,
from drivers/mtd/mtdconcat.c:25:
include/image.h: In function ‘image_check_target_arch’:
include/image.h:846:3: error: #error "please define IH_ARCH_DEFAULT in
your arch asm/u-boot.h"
# error "please define IH_ARCH_DEFAULT in your arch asm/u-boot.h"
^~~~~
include/image.h:848:31: error: ‘IH_ARCH_DEFAULT’ undeclared (first use in
this function); did you mean ‘IH_ARCH_COUNT’?
return image_check_arch(hdr, IH_ARCH_DEFAULT);
The error can be avoided by moving the definition of IH_ARCH_DEFAULT before
#include <asm/ppc.h>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Tom Rini [Thu, 28 Feb 2019 23:57:32 +0000 (18:57 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-socfpga
- SoCFPGA cache/gpio fixes
Tom Rini [Thu, 28 Feb 2019 23:57:17 +0000 (18:57 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-sh
- Gen2/Gen3 fixes for warnings and sdhi
Tom Rini [Thu, 28 Feb 2019 19:22:50 +0000 (14:22 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-sunxi
- Various Bananapi fixes
Tom Rini [Thu, 28 Feb 2019 19:22:03 +0000 (14:22 -0500)]
Merge branch '2019-02-29-master-imports'
- Assorted BSP fixes
- Kbuild fix
Simon Goldschmidt [Tue, 26 Feb 2019 21:27:52 +0000 (22:27 +0100)]
spl: add debug print for early malloc usage
To find out how big the early malloc heap must be in SPL, add a debug
print statement that dumps its usage before switching to relocated heap
in spl_relocate_stack_gd() via CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Stephen Warren [Tue, 26 Feb 2019 19:20:26 +0000 (12:20 -0700)]
kbuild: fix DTB .cmd source variable
*.dts are processed using a custom command, then the C pre-processor is
run on them, then they are compiled using dtc. Thus, the dependency
files generated by both cpp and dtc reference a temporary file name
rather than the actual source file. While this information isn't used
for any purpose by the build system, and hence this causes no functional
issue, it does cause the dependency files to contain invalid and
confusing data, which is unhelpful while debugging build problems. Fix
this using sed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Stephen Warren [Tue, 26 Feb 2019 19:20:25 +0000 (12:20 -0700)]
kbuild: make arch-dtbs target PHONY
Without this, the arch-dtbs target only gets evaluated when building
U-Boot the first time, not when re-building (incrementally building)
U-Boot. Thus incremental builds ignore changes to DTB files.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Patrick Delaunay [Tue, 26 Feb 2019 12:09:00 +0000 (13:09 +0100)]
doc: binding: rename directory ram to memory-controller
Alignment with kernel directory name as it have already bindings for
DDR controllers in the directory:
Documentation/devicetree/bindings/memory-controller
PS: the drivers using RAM u-class should be associated with
this binding directory
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Heinrich Schuchardt [Mon, 25 Feb 2019 18:42:48 +0000 (19:42 +0100)]
fs: fat: fix link error when building with DEBUG=1
When compiling with DEBUG=1 an error
fs/fat/fat_write.c:831: undefined reference to `__aeabi_ldivmod'
occurred.
We should use do_div() instead of the modulus operator.
filesize and cur_pos cannot be negative. So let's use u64 to avoid
warnings.
Fixes:
cb8af8af5ba0 ("fs: fat: support write with non-zero offset")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Felix Brack [Mon, 25 Feb 2019 15:38:23 +0000 (16:38 +0100)]
arm: pdu001: Fix order of include files
Fix the order of include files according to U-Boot coding style.
Signed-off-by: Felix Brack <fb@ltec.ch>
Michal Simek [Thu, 21 Feb 2019 06:48:54 +0000 (07:48 +0100)]
.gitignore: Ignore regenerated *.dtbo files
*.dtbo are dt overlays files which should be also ignored as *.dtb.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Marek Vasut [Tue, 19 Feb 2019 00:43:51 +0000 (01:43 +0100)]
ARM: cache: Fix incorrect bitwise operation
The loop implemented in the code is supposed to check whether the
PL310 operation register has any bit from the mask set. Currently,
the code checks whether the PL310 operation register has any bit
set AND whether the mask is non-zero, which is incorrect. Fix the
conditional.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Tom Rini <trini@konsulko.com>
Fixes:
93bc21930a1b ("armv7: add PL310 support to u-boot")
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Dinh Nguyen <dinguyen@kernel.org>
David Rivshin [Mon, 18 Feb 2019 23:04:29 +0000 (18:04 -0500)]
spi: omap3: fix set_wordlen() reading from incorrect address for CHCONF
_omap3_spi_set_wordlen() indexed the regs->channel[] array with the
old wordlen (instead of the chipselect number) when reading the current
CHCONF register value. This meant it read from the wrong memory location,
modified that value, and then wrote it back to the correct CHCONF
register. The end result is that most slave configuration settings would
be lost, such as clock divisor, clock/chipselect polarities, etc.
Fixes:
77b8d04854f4 ("spi: omap3: Convert to driver model")
Signed-off-by: David Rivshin <drivshin@allworx.com>
Tom Rini [Wed, 27 Feb 2019 18:32:09 +0000 (13:32 -0500)]
Merge git://git.denx.de/u-boot-riscv
- SiFive FU540 Support
Anup Patel [Mon, 25 Feb 2019 08:15:33 +0000 (08:15 +0000)]
riscv: Enable CONFIG_SYS_BOOT_RAMDISK_HIGH for using initrd
This patch enables CONFIG_SYS_BOOT_RAMDISK_HIGH for RISC-V
because bootm will update initrd location in DTB only if
CONFIG_SYS_BOOT_RAMDISK_HIGH is enabled. If we don't enable
this option then bootm assumes DTB already has initrd details
which is not the case most of the time.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Atish Patra [Mon, 25 Feb 2019 08:15:27 +0000 (08:15 +0000)]
doc: Add a readme guide for SiFive FU540
The readme guide describes the procedure to build, flash and boot Linux
using U-Boot on HiFive Unleashed. It also explains the current state of
U-boot support and future action items.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Anup Patel [Mon, 25 Feb 2019 08:15:19 +0000 (08:15 +0000)]
riscv: Add SiFive FU540 board support
This patch adds SiFive FU540 board support. For now, only
SiFive serial, SiFive PRCI, and Cadance MACB drivers are
only enabled. The SiFive FU540 defconfig by default builds
U-Boot for S-Mode because U-Boot on SiFive FU540 will run
in S-Mode as payload of BBL or OpenSBI.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Atish Patra [Mon, 25 Feb 2019 08:15:14 +0000 (08:15 +0000)]
cpu: Bind timer driver for boot hart
Currently, timer driver is bound only for hart0.
There is no mandatory requirement that hart0 should always
come up. In fact, HiFive Unleashed SoC hart0 doesn't boot
in S-mode because it only has M-mode.
The timer driver should be bound for boot hart.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Atish Patra [Mon, 25 Feb 2019 08:15:08 +0000 (08:15 +0000)]
drivers: serial_sifive: Skip baudrate config if no input clock
It is possible that input clock is not available because clk
device was not available and 'clock-frequency' DT property is
also not available.
In this case, instead of failing we should just skip baudrate
config by returning zero.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Atish Patra [Mon, 25 Feb 2019 08:15:02 +0000 (08:15 +0000)]
drivers: serial_sifive: Fix baud rate calculation
Compute the baud rate multipler with more precision.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Anup Patel [Mon, 25 Feb 2019 08:14:55 +0000 (08:14 +0000)]
clk: Add fixed-factor clock driver
This patch adds fixed-factor clock driver which derives clock
rate by dividing (div) and multiplying (mult) fixed factors
to a parent clock.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Anup Patel [Mon, 25 Feb 2019 08:14:49 +0000 (08:14 +0000)]
clk: Add SiFive FU540 PRCI clock driver
Add driver code for the SiFive FU540 PRCI IP block. This IP block
handles reset and clock control for the SiFive FU540 device and
implements SoC-level clock tree controls and dividers.
Based on code written by Wesley Terpstra <wesley@sifive.com>
found in commit
999529edf517ed75b56659d456d221b2ee56bb60 of:
https://github.com/riscv/riscv-linux
Boot and PLL rate change were tested on a SiFive HiFive Unleashed
board.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Atish Patra [Mon, 25 Feb 2019 08:14:42 +0000 (08:14 +0000)]
net: macb: Fix GEM hardware detection
Fix MID bit field check to correctly identify all GEM hardwares.
The check is updated as per macb driver in Linux location:
<linux_sources>/drivers/net/ethernet/cadence/macb_main.c:259
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Anup Patel [Mon, 25 Feb 2019 08:14:36 +0000 (08:14 +0000)]
net: macb: Fix clk API usage for RISC-V systems
Don't fail in macb_enable_clk() if clk_enable() returns
-ENOSYS because we get -ENOSYS for fixed-rate clocks.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>