Peter Rosin [Mon, 25 May 2020 10:43:52 +0000 (12:43 +0200)]
spi: mux: repair mux usage
It is not valid to cache/short out selection of the mux.
mux_control_select() only locks the mux until mux_control_deselect()
is called. mux_control_deselect() may put the mux in some low power
state or some other user of the mux might select it for other purposes.
These things are probably not happening in the original setting where
this driver was developed, but it is said to be a generic SPI mux.
Also, the mux framework will short out the actual low level muxing
operation when/if that is possible.
Fixes:
e9e40543ad5b ("spi: Add generic SPI multiplexer")
Signed-off-by: Peter Rosin <peda@axentia.se>
Link: https://lore.kernel.org/r/20200525104352.26807-1-peda@axentia.se
Signed-off-by: Mark Brown <broonie@kernel.org>
Lukas Wunner [Fri, 15 May 2020 15:58:03 +0000 (17:58 +0200)]
spi: bcm2835aux: Fix controller unregister order
The BCM2835aux SPI driver uses devm_spi_register_master() on bind.
As a consequence, on unbind, __device_release_driver() first invokes
bcm2835aux_spi_remove() before unregistering the SPI controller via
devres_release_all().
This order is incorrect: bcm2835aux_spi_remove() turns off the SPI
controller, including its interrupts and clock. The SPI controller
is thus no longer usable.
When the SPI controller is subsequently unregistered, it unbinds all
its slave devices. If their drivers need to access the SPI bus,
e.g. to quiesce their interrupts, unbinding will fail.
As a rule, devm_spi_register_master() must not be used if the
->remove() hook performs teardown steps which shall be performed
after unbinding of slaves.
Fix by using the non-devm variant spi_register_master(). Note that the
struct spi_master as well as the driver-private data are not freed until
after bcm2835aux_spi_remove() has finished, so accessing them is safe.
Fixes:
1ea29b39f4c8 ("spi: bcm2835aux: add bcm2835 auxiliary spi device driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.4+
Cc: Martin Sperl <kernel@martin.sperl.org>
Link: https://lore.kernel.org/r/32f27f4d8242e4d75f9a53f7e8f1f77483b08669.1589557526.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Lukas Wunner [Fri, 15 May 2020 15:58:02 +0000 (17:58 +0200)]
spi: bcm2835: Fix controller unregister order
The BCM2835 SPI driver uses devm_spi_register_controller() on bind.
As a consequence, on unbind, __device_release_driver() first invokes
bcm2835_spi_remove() before unregistering the SPI controller via
devres_release_all().
This order is incorrect: bcm2835_spi_remove() tears down the DMA
channels and turns off the SPI controller, including its interrupts
and clock. The SPI controller is thus no longer usable.
When the SPI controller is subsequently unregistered, it unbinds all
its slave devices. If their drivers need to access the SPI bus,
e.g. to quiesce their interrupts, unbinding will fail.
As a rule, devm_spi_register_controller() must not be used if the
->remove() hook performs teardown steps which shall be performed
after unbinding of slaves.
Fix by using the non-devm variant spi_register_controller(). Note that
the struct spi_controller as well as the driver-private data are not
freed until after bcm2835_spi_remove() has finished, so accessing them
is safe.
Fixes:
247263dba208 ("spi: bcm2835: use devm_spi_register_master()")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.13+
Link: https://lore.kernel.org/r/2397dd70cdbe95e0bc4da2b9fca0f31cb94e5aed.1589557526.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Lukas Wunner [Fri, 15 May 2020 15:58:01 +0000 (17:58 +0200)]
spi: Fix controller unregister order
When an SPI controller unregisters, it unbinds all its slave devices.
For this, their drivers may need to access the SPI bus, e.g. to quiesce
interrupts.
However since commit
ffbbdd21329f ("spi: create a message queueing
infrastructure"), spi_destroy_queue() is executed before unbinding the
slaves. It sets ctlr->running = false, thereby preventing SPI bus
access and causing unbinding of slave devices to fail.
Fix by unbinding slaves before calling spi_destroy_queue().
Fixes:
ffbbdd21329f ("spi: create a message queueing infrastructure")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.4+
Cc: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/8aaf9d44c153fe233b17bc2dec4eb679898d7e7b.1589557526.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Florian Fainelli [Mon, 20 Apr 2020 19:08:45 +0000 (15:08 -0400)]
spi: bcm-qspi: Handle clock probe deferral
The clock provider may not be ready by the time spi-bcm-qspi gets
probed, handle probe deferral using devm_clk_get_optional().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200420190853.45614-2-kdasu.kdev@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Justin Chen [Mon, 20 Apr 2020 19:08:49 +0000 (15:08 -0400)]
spi: bcm-qspi: when tx/rx buffer is NULL set to 0
Currently we set the tx/rx buffer to 0xff when NULL. This causes
problems with some spi slaves where 0xff is a valid command. Looking
at other drivers, the tx/rx buffer is usually set to 0x00 when NULL.
Following this convention solves the issue.
Fixes:
fa236a7ef240 ("spi: bcm-qspi: Add Broadcom MSPI driver")
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200420190853.45614-6-kdasu.kdev@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Kamal Dasu [Mon, 20 Apr 2020 19:08:50 +0000 (15:08 -0400)]
spi: bcm-qspi: Make PM suspend/resume work with SCMI clock management
SCMI only passes clk_prepare_enable() and clk_disable_unprepare(), made
changes to suspend/resume ops to use the appropriate calls so that PM
works for ARM and ARM64 platforms.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Link: https://lore.kernel.org/r/20200420190853.45614-7-kdasu.kdev@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Kamal Dasu [Mon, 20 Apr 2020 19:08:48 +0000 (15:08 -0400)]
spi: bcm-qspi: Drive MSPI peripheral SSb pin on cs_change
As per the spi core implementation for MSPI devices when the transfer is
the last one in the message, the chip may stay selected until the next
transfer. On multi-device SPI busses with nothing blocking messages going
to other devices, this is just a performance hint; starting a message to
another device deselects this one. But in other cases, this can be used
to ensure correctness. Some devices need protocol transactions to be built
from a series of spi_message submissions, where the content of one message
is determined by the results of previous messages and where the whole
transaction ends when the chipselect goes intactive.
On CS change after completing the last serial transfer, the MSPI driver
drives SSb pin CDRAM register correctly according comments in core spi.h
as shown below:
case 1) EOM =1, cs_change =0: SSb inactive
case 2) EOM =1, cs_change =1: SSb active
case 3) EOM =0, cs_change =0: SSb active
case 4) EOM =0, cs_change =1: SSb inactive
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Link: https://lore.kernel.org/r/20200420190853.45614-5-kdasu.kdev@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Andy Shevchenko [Mon, 13 Apr 2020 18:04:06 +0000 (21:04 +0300)]
spi: Respect DataBitLength field of SpiSerialBusV2() ACPI resource
By unknown reason the commit
64bee4d28c9e
("spi / ACPI: add ACPI enumeration support")
missed the DataBitLength property to encounter when parse SPI slave
device data from ACPI.
Fill the gap here.
Fixes:
64bee4d28c9e ("spi / ACPI: add ACPI enumeration support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200413180406.1826-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Christophe JAILLET [Mon, 13 Apr 2020 15:40:43 +0000 (17:40 +0200)]
spi: sc18is602: Fix a typo in MODULE_DESCRIPTION
This should be 'SC18IS602', not 'SC18IC602'
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20200413154043.23064-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Rafał Hibner [Thu, 9 Apr 2020 15:56:21 +0000 (17:56 +0200)]
spi: spi-axi-spi-engine: Access register after clock initialization
Move register access after clock initialization.
Clock "s_axi_aclk" is needed for register access. Without the clock running
AXI bus hangs and causes kernel freeze.
Signed-off-by: Rafał Hibner <rafal.hibner@secom.com.pl>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20200409155621.12174-1-rafal.hibner@secom.com.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Jungseung Lee [Thu, 2 Apr 2020 12:10:22 +0000 (21:10 +0900)]
spi: spi-ep93xx: fix wrong SPI mode selection
The mode bits on control register 0 are in a different order compared
to the spi mode define values. Thus, in the current code, it fails to
set the correct SPI mode selection. Fix it.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Link: https://lore.kernel.org/r/20200402121022.9976-1-js07.lee@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Linus Walleij [Tue, 17 Mar 2020 09:49:14 +0000 (10:49 +0100)]
spi: efm32: Convert to use GPIO descriptors
This switches the EFM32 driver over to use the GPIO descriptor
handling in the core. The GPIO handling in this driver is
pretty simplistic so this should just work. Drop the GPIO headers
and insert the implicitly included <linux/of.h> header.
Signed-off-by: Linus Walleij <linus.walleij-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Cc: Uwe Kleine-König <u.kleine-koenig-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
Link: https://lore.kernel.org/r/20200317094914.331932-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Gustavo A. R. Silva [Fri, 20 Mar 2020 23:25:15 +0000 (18:25 -0500)]
spi: spi-fsl-lpspi: Replace zero-length array with flexible-array member
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit
76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200320232515.GA24800@embeddedor.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Gustavo A. R. Silva [Fri, 20 Mar 2020 23:25:56 +0000 (18:25 -0500)]
spi: spi-s3c24xx: Replace zero-length array with flexible-array member
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit
76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Andi Shyti <andi@etezian.org>
Link: https://lore.kernel.org/r/20200320232556.GA24989@embeddedor.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Alain Volmat [Fri, 20 Mar 2020 13:44:17 +0000 (14:44 +0100)]
spi: stm32: Fix comments compilation warnings
Fix all functions and structure descriptions to have the driver
warning free when built with W=1.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/1584711857-9162-1-git-send-email-alain.volmat@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Tudor Ambarus [Fri, 20 Mar 2020 06:51:01 +0000 (06:51 +0000)]
spi: atmel-quadspi: Add verbose debug facilities to monitor register accesses
This feature should not be enabled in release but can be useful for
developers who need to monitor register accesses at some specific places.
Helped me identify a bug in u-boot, by comparing the register accesses
from the linux driver with the ones from its u-boot variant.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200320065058.891221-1-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vladimir Oltean [Wed, 18 Mar 2020 00:16:01 +0000 (02:16 +0200)]
spi: spi-fsl-dspi: Add support for LS1028A
This is similar to the DSPI instantiation on LS1028A, except that:
- The A-011218 erratum has been fixed, so DMA works
- The endianness is different, which has implications on XSPI mode
Some benchmarking with the following command:
spidev_test --device /dev/spidev2.0 --bpw 8 --size 256 --cpha --iter
10000000 --speed
20000000
shows that in DMA mode, it can achieve around 2400 kbps, and in XSPI
mode, the same command goes up to 4700 kbps. This is somewhat to be
expected, since the DMA buffer size is extremely small at 8 bytes, the
winner becomes whomever can prepare the buffers for transmission
quicker, and DMA mode has higher overhead there. So XSPI FIFO mode has
been chosen as the operating mode for this chip.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200318001603.9650-11-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vladimir Oltean [Wed, 18 Mar 2020 00:16:00 +0000 (02:16 +0200)]
spi: spi-fsl-dspi: Move invariant configs out of dspi_transfer_one_message
The operating mode (DMA, XSPI, EOQ) is not going to change across the
lifetime of the device. So it makes no sense to keep writing to SPI_RSER
on each message. Move this configuration to dspi_init instead.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200318001603.9650-10-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vladimir Oltean [Wed, 18 Mar 2020 00:15:59 +0000 (02:15 +0200)]
spi: spi-fsl-dspi: Fix interrupt-less DMA mode taking an XSPI code path
Interrupts are not necessary for DMA functionality, since the completion
event is provided by the DMA driver.
But if the driver fails to request the IRQ defined in the device tree,
it will call dspi_poll which would make the driver hang waiting for data
to become available in the RX FIFO.
Fixes:
c55be3059159 ("spi: spi-fsl-dspi: Use poll mode in case the platform IRQ is missing")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200318001603.9650-9-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vladimir Oltean [Wed, 18 Mar 2020 00:15:58 +0000 (02:15 +0200)]
spi: spi-fsl-dspi: Avoid NULL pointer in dspi_slave_abort for non-DMA mode
The driver does not create the dspi->dma structure unless operating in
DSPI_DMA_MODE, so it makes sense to check for that.
Fixes:
f4b323905d8b ("spi: Introduce dspi_slave_abort() function for NXP's dspi SPI driver")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200318001603.9650-8-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vladimir Oltean [Wed, 18 Mar 2020 00:15:57 +0000 (02:15 +0200)]
spi: spi-fsl-dspi: Replace interruptible wait queue with a simple completion
Currently the driver puts the process in interruptible sleep waiting for
the interrupt train to finish transfer to/from the tx_buf and rx_buf.
But exiting the process with ctrl-c may make the kernel panic: the
wait_event_interruptible call will return -ERESTARTSYS, which a proper
driver implementation is perhaps supposed to handle, but nonetheless
this one doesn't, and aborts the transfer altogether.
Actually when the task is interrupted, there is still a high chance that
the dspi_interrupt is still triggering. And if dspi_transfer_one_message
returns execution all the way to the spi_device driver, that can free
the spi_message and spi_transfer structures, leaving the interrupts to
access a freed tx_buf and rx_buf.
hexdump -C /dev/mtd0
00000000 00 75 68 75 0a ff ff ff ff ff ff ff ff ff ff ff
|.uhu............|
00000010 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
|................|
*
^C[ 38.495955] fsl-dspi 2120000.spi: Waiting for transfer to complete failed!
[ 38.503097] spi_master spi2: failed to transfer one message from queue
[ 38.509729] Unable to handle kernel paging request at virtual address
ffff800095ab3377
[ 38.517676] Mem abort info:
[ 38.520474] ESR = 0x96000045
[ 38.523533] EC = 0x25: DABT (current EL), IL = 32 bits
[ 38.528861] SET = 0, FnV = 0
[ 38.531921] EA = 0, S1PTW = 0
[ 38.535067] Data abort info:
[ 38.537952] ISV = 0, ISS = 0x00000045
[ 38.541797] CM = 0, WnR = 1
[ 38.544771] swapper pgtable: 4k pages, 48-bit VAs, pgdp=
0000000082621000
[ 38.551494] [
ffff800095ab3377] pgd=
00000020fffff003, p4d=
00000020fffff003, pud=
0000000000000000
[ 38.560229] Internal error: Oops:
96000045 [#1] PREEMPT SMP
[ 38.565819] Modules linked in:
[ 38.568882] CPU: 0 PID: 2729 Comm: hexdump Not tainted 5.6.0-rc4-next-
20200306-00052-gd8730cdc8a0b-dirty #193
[ 38.578834] Hardware name: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier (DT)
[ 38.587129] pstate:
20000085 (nzCv daIf -PAN -UAO)
[ 38.591941] pc : ktime_get_real_ts64+0x3c/0x110
[ 38.596487] lr : spi_take_timestamp_pre+0x40/0x90
[ 38.601203] sp :
ffff800010003d90
[ 38.604525] x29:
ffff800010003d90 x28:
ffff80001200e000
[ 38.609854] x27:
ffff800011da9000 x26:
ffff002079c40400
[ 38.615184] x25:
ffff8000117fe018 x24:
ffff800011daa1a0
[ 38.620513] x23:
ffff800015ab3860 x22:
ffff800095ab3377
[ 38.625841] x21:
000000000000146e x20:
ffff8000120c3000
[ 38.631170] x19:
ffff0020795f6e80 x18:
ffff800011da9948
[ 38.636498] x17:
0000000000000000 x16:
0000000000000000
[ 38.641826] x15:
ffff800095ab3377 x14:
0720072007200720
[ 38.647155] x13:
0720072007200765 x12:
0775076507750771
[ 38.652483] x11:
0720076d076f0772 x10:
0000000000000040
[ 38.657812] x9 :
ffff8000108e2100 x8 :
ffff800011dcabe8
[ 38.663139] x7 :
0000000000000000 x6 :
ffff800015ab3a60
[ 38.668468] x5 :
0000000007200720 x4 :
ffff800095ab3377
[ 38.673796] x3 :
0000000000000000 x2 :
0000000000000ab0
[ 38.679125] x1 :
ffff800011daa000 x0 :
0000000000000026
[ 38.684454] Call trace:
[ 38.686905] ktime_get_real_ts64+0x3c/0x110
[ 38.691100] spi_take_timestamp_pre+0x40/0x90
[ 38.695470] dspi_fifo_write+0x58/0x2c0
[ 38.699315] dspi_interrupt+0xbc/0xd0
[ 38.702987] __handle_irq_event_percpu+0x78/0x2c0
[ 38.707706] handle_irq_event_percpu+0x3c/0x90
[ 38.712161] handle_irq_event+0x4c/0xd0
[ 38.716008] handle_fasteoi_irq+0xbc/0x170
[ 38.720115] generic_handle_irq+0x2c/0x40
[ 38.724135] __handle_domain_irq+0x68/0xc0
[ 38.728243] gic_handle_irq+0xc8/0x160
[ 38.732000] el1_irq+0xb8/0x180
[ 38.735149] spi_nor_spimem_read_data+0xe0/0x140
[ 38.739779] spi_nor_read+0xc4/0x120
[ 38.743364] mtd_read_oob+0xa8/0xc0
[ 38.746860] mtd_read+0x4c/0x80
[ 38.750007] mtdchar_read+0x108/0x2a0
[ 38.753679] __vfs_read+0x20/0x50
[ 38.757002] vfs_read+0xa4/0x190
[ 38.760237] ksys_read+0x6c/0xf0
[ 38.763471] __arm64_sys_read+0x20/0x30
[ 38.767319] el0_svc_common.constprop.3+0x90/0x160
[ 38.772125] do_el0_svc+0x28/0x90
[ 38.775449] el0_sync_handler+0x118/0x190
[ 38.779468] el0_sync+0x140/0x180
[ 38.782793] Code:
91000294 1400000f d50339bf f9405e80 (
f90002c0)
[ 38.788910] ---[ end trace
55da560db4d6bef7 ]---
[ 38.793540] Kernel panic - not syncing: Fatal exception in interrupt
[ 38.799914] SMP: stopping secondary CPUs
[ 38.803849] Kernel Offset: disabled
[ 38.807344] CPU features: 0x10002,
20006008
[ 38.811451] Memory Limit: none
[ 38.814513] ---[ end Kernel panic - not syncing: Fatal exception in interrupt ]---
So it is clear that the "interruptible" part isn't handled correctly.
When the process receives a signal, one could either attempt a clean
abort (which appears to be difficult with this hardware) or just keep
restarting the sleep until the wait queue really completes. But checking
in a loop for -ERESTARTSYS is a bit too complicated for this driver, so
just make the sleep uninterruptible, to avoid all that nonsense.
The wait queue was actually restructured as a completion, after polling
other drivers for the most "popular" approach.
Fixes:
349ad66c0ab0 ("spi:Add Freescale DSPI driver for Vybrid VF610 platform")
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200318001603.9650-7-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vladimir Oltean [Wed, 18 Mar 2020 00:15:56 +0000 (02:15 +0200)]
spi: spi-fsl-dspi: Protect against races on dspi->words_in_flight
dspi->words_in_flight is a variable populated in the *_write functions
and used in the dspi_fifo_read function. It is also used in
dspi_fifo_write, immediately after transmission, to update the
message->actual_length variable used by higher layers such as spi-mem
for integrity checking.
But it may happen that the IRQ which calls dspi_fifo_read to be
triggered before the updating of message->actual_length takes place. In
that case, dspi_fifo_read will decrement dspi->words_in_flight to -1,
and that will cause an invalid modification of message->actual_length.
For that, we make the simplest fix possible: to not decrement the actual
shared variable in dspi->words_in_flight from dspi_fifo_read, but
actually a copy of it which is on stack.
But even if dspi_fifo_read from the next IRQ does not interfere with the
dspi_fifo_write of the current chunk, the *next* dspi_fifo_write still
can. So we must assume that everything after the last write to the TX
FIFO can be preempted by the "TX complete" IRQ, and the dspi_fifo_write
function must be safe against that. This means refactoring the 2
flavours of FIFO writes (for EOQ and XSPI) such that the calculation of
the number of words to be written is common and happens a priori. This
way, the code for updating the message->actual_length variable works
with a copy and not with the volatile dspi->words_in_flight.
After some interior debate, the dspi->progress variable used for
software timestamping was *not* backed up against preemption in a copy
on stack. Because if preemption does occur between
spi_take_timestamp_pre and spi_take_timestamp_post, there's really no
point in trying to save anything. The first-in-time
spi_take_timestamp_post call with a dspi->progress higher than the
requested xfer->ptp_sts_word_post will trigger xfer->timestamped = true
anyway and will close the deal.
To understand the above a bit better, consider a transfer with
xfer->ptp_sts_word_pre = xfer->ptp_sts_word_post = 3, and
xfer->bits_per_words = 8 (so byte 3 needs to be timestamped). The DSPI
controller timestamps in chunks of 4 bytes at a time, and preemption
occurs in the middle of timestamping the first chunk:
spi_take_timestamp_pre(0)
.
. (preemption)
.
. spi_take_timestamp_pre(4)
.
. spi_take_timestamp_post(7)
.
spi_take_timestamp_post(3)
So the reason I'm not bothering to back up dspi->progress for that
spi_take_timestamp_post(3) is that spi_take_timestamp_post(7) is going
to (a) be more honest, (b) provide better accuracy and (c) already
render the spi_take_timestamp_post(3) into a noop by setting
xfer->timestamped = true anyway.
Fixes:
d59c90a2400f ("spi: spi-fsl-dspi: Convert TCFQ users to XSPI FIFO mode")
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200318001603.9650-6-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vladimir Oltean [Wed, 18 Mar 2020 00:15:55 +0000 (02:15 +0200)]
spi: spi-fsl-dspi: Avoid reading more data than written in EOQ mode
If dspi->words_in_flight is populated with the hardware FIFO size,
then in dspi_fifo_read it will attempt to read more data at the end of a
buffer that is not a multiple of 16 bytes in length. It will probably
time out attempting to do so.
So limit the num_fifo_entries variable to the actual number of FIFO
entries that is going to be used.
Fixes:
d59c90a2400f ("spi: spi-fsl-dspi: Convert TCFQ users to XSPI FIFO mode")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200318001603.9650-5-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vladimir Oltean [Wed, 18 Mar 2020 00:15:54 +0000 (02:15 +0200)]
spi: spi-fsl-dspi: Fix bits-per-word acceleration in DMA mode
In DMA mode, dspi_setup_accel does not get called, which results in the
dspi->oper_word_size variable (which is used by dspi_dma_xfer) to not be
initialized properly.
Because oper_word_size is zero, a few calculations end up being
incorrect, and the DMA transfer eventually times out instead of sending
anything on the wire.
Set up native transfers (or 8-on-16 acceleration) using dspi_setup_accel
for DMA mode too.
Also take the opportunity and simplify the DMA buffer handling a little
bit.
Fixes:
6c1c26ecd9a3 ("spi: spi-fsl-dspi: Accelerate transfers using larger word size if possible")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200318001603.9650-4-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vladimir Oltean [Wed, 18 Mar 2020 00:15:53 +0000 (02:15 +0200)]
spi: spi-fsl-dspi: Fix little endian access to PUSHR CMD and TXDATA
In XSPI mode, the 32-bit PUSHR register can be written to separately:
the higher 16 bits are for commands and the lower 16 bits are for data.
This has nicely been hacked around, by defining a second regmap with a
width of 16 bits, and effectively splitting a 32-bit register into 2
16-bit ones, from the perspective of this regmap_pushr.
The problem is the assumption about the controller's endianness. If the
controller is little endian (such as anything post-LS1046A), then the
first 2 bytes, in the order imposed by memory layout, will actually hold
the TXDATA, and the last 2 bytes will hold the CMD.
So take the controller's endianness into account when performing split
writes to PUSHR. The obvious and simple solution would have been to call
regmap_get_val_endian(), but that is an internal regmap function and we
don't want to change regmap just for this. Therefore, we just re-read
the "big-endian" device tree property.
Fixes:
58ba07ec79e6 ("spi: spi-fsl-dspi: Add support for XSPI mode registers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200318001603.9650-3-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vladimir Oltean [Wed, 18 Mar 2020 00:15:52 +0000 (02:15 +0200)]
spi: spi-fsl-dspi: Don't access reserved fields in SPI_MCR
The SPI_MCR_PCSIS macro assumes that the controller has a number of chip
select signals equal to 6. That is not always the case, but actually is
described through the driver-specific "spi-num-chipselects" device tree
binding. LS1028A for example only has 4 chip selects.
Don't write to the upper bits of the PCSIS field, which are reserved in
the reference manual.
Fixes:
349ad66c0ab0 ("spi:Add Freescale DSPI driver for Vybrid VF610 platform")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200318001603.9650-2-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Linus Walleij [Tue, 17 Mar 2020 09:24:57 +0000 (10:24 +0100)]
spi: mxs: Drop GPIO includes
This driver is not using any symbols from the GPIO .h files
so drop them.
It was however implicitly using <linux/pinctrl/consumer.h>
so include that instead.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200317092457.264055-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Geert Uytterhoeven [Fri, 6 Mar 2020 08:50:38 +0000 (09:50 +0100)]
spi: dt-bindings: spi-controller: Fix spi-[rt]x-bus-width for slave mode
The descriptions for the spi-rx-bus-width and spi-tx-bus-width
properties refer to "MISO" and "MOSI", which are not explained in the
document. While these abbreviations are fairly common when talking
about SPI, and thus may not need an explanation, they are not entirely
correct in this context, as the SPI controller may be used in slave mode
instead of master mode.
Fix this by replacing them by "read transfers" resp. "write transfers",
like is done for the spi-rx-delay-us and spi-tx-delay-us properties.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200306085038.8111-3-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Geert Uytterhoeven [Fri, 6 Mar 2020 08:50:37 +0000 (09:50 +0100)]
spi: dt-bindings: spi-controller: Fix #address-cells for slave mode
Currently, the DT bindings for an SPI controller specify that
"#address-cells" must be fixed to one. However, that applies to an SPI
controller in master mode only. When running in SPI slave mode,
"#address-cells" should not be specified.
Fix this making "#address-cells" mutually-exclusive with "spi-slave".
Fixes:
0a1b929356830257 ("spi: Add YAML schemas for the generic SPI options")
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200306085038.8111-2-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Thu, 12 Mar 2020 17:38:42 +0000 (17:38 +0000)]
Merge series "spi: meson-spicc: add support for AXG and G12A variants" from Neil Armstrong <narmstrong@baylibre.com>:
The SPICC controller in Amlogic AXG & G12A is capable of driving the
CLK/MOSI/SS signal lines through the idle state which avoid the signals
floating in unexpected state, is capable of using linear clock divider
to reach a much fine tuned range of clocks, while the old controller only
uses a power of two clock divider, result at a more coarse clock range and
finally is capable of running at 80M clock.
The SPICC controller in Amlogic G12A takes the source clock from a specific
clock instead of the bus clock and has a different FIFO size and doesn't
handle the RX Half interrupt the same way as GXL & AXG variants. Thus
the burst management is simplified and takes in account a variable FIFO
size.
Now the controller can support frequencies higher than 30MHz, we need
the setup the I/O line delays in regard of the SPI clock frequency.
Neil Armstrong (7):
spi: meson-spicc: remove unused variables
spi: meson-spicc: support max 80MHz clock
spi: meson-spicc: add min sclk for each compatible
spi: meson-spicc: setup IO line delay
spi: meson-spicc: adapt burst handling for G12A support
dt-bindings: spi: amlogic,meson-gx-spicc: add Amlogic G12A compatible
spi: meson-spicc: add support for Amlogic G12A
Sunny Luo (2):
spi: meson-spicc: enhance output enable feature
spi: meson-spicc: add a linear clock divider support
.../bindings/spi/amlogic,meson-gx-spicc.yaml | 22 +
drivers/spi/Kconfig | 1 +
drivers/spi/spi-meson-spicc.c | 496 +++++++++++++-----
3 files changed, 392 insertions(+), 127 deletions(-)
--
2.22.0
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
Wolfram Sang [Thu, 12 Mar 2020 13:45:07 +0000 (14:45 +0100)]
spi: acpi: remove superfluous parameter check
to_spi_device() already checks 'dev'. No need to do it before calling
it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200312134507.10000-1-wsa@the-dreams.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Neil Armstrong [Thu, 12 Mar 2020 13:31:30 +0000 (14:31 +0100)]
spi: dt-bindings: amlogic, meson-gx-spicc: add Amlogic G12A compatible
The Amlogic G12A SPICC controllers uses a secondary clock used to feed the
baud rate generator and the delay control logic.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200312133131.26430-9-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Neil Armstrong [Thu, 12 Mar 2020 13:31:31 +0000 (14:31 +0100)]
spi: meson-spicc: add support for Amlogic G12A
Add support for the SPICC controllers on the Amlogic G12A SoCs family.
The G12A SPICC controllers inherit from the AXG enhanced registers but
takes an external pclk for the baud rate generator and can achieve up to
166MHz SCLK.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200312133131.26430-10-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Neil Armstrong [Thu, 12 Mar 2020 13:31:29 +0000 (14:31 +0100)]
spi: meson-spicc: adapt burst handling for G12A support
The G12A SPICC controller variant has a different FIFO size and doesn't
handle the RX Half interrupt the same way as GXL & AXG variants.
Thus simplify the burst management and take in account a variable FIFO
size.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200312133131.26430-8-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Neil Armstrong [Thu, 12 Mar 2020 13:31:28 +0000 (14:31 +0100)]
spi: meson-spicc: setup IO line delay
Now the controller can support frequencies higher than 30MHz, we need
the setup the I/O line delays in regard of the SPI clock frequency.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200312133131.26430-7-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Neil Armstrong [Thu, 12 Mar 2020 13:31:27 +0000 (14:31 +0100)]
spi: meson-spicc: add min sclk for each compatible
The G12A SPICC controller variant takes the source clock from a specific
clock instead of the bus clock.
The minimal clock calculus won't work with the G12A support, thus add the
minimal supported clock for each variant and pass this to the SPI core.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200312133131.26430-6-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Neil Armstrong [Thu, 12 Mar 2020 13:31:26 +0000 (14:31 +0100)]
spi: meson-spicc: support max 80MHz clock
The SPICC controller in Meson-AXG is capable of running at 80M clock.
The ASIC IP is improved and the clock is actually running higher than
previous old SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Sunny Luo <sunny.luo@amlogic.com>
Link: https://lore.kernel.org/r/20200312133131.26430-5-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Sunny Luo [Thu, 12 Mar 2020 13:31:25 +0000 (14:31 +0100)]
spi: meson-spicc: add a linear clock divider support
The SPICC controller in Meson-AXG SoC is capable of using
a linear clock divider to reach a much fine tuned range of clocks,
while the old controller only use a power of two clock divider,
result at a more coarse clock range.
Also convert the clock registration into Common Clock Framework.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Sunny Luo <sunny.luo@amlogic.com>
Link: https://lore.kernel.org/r/20200312133131.26430-4-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Sunny Luo [Thu, 12 Mar 2020 13:31:24 +0000 (14:31 +0100)]
spi: meson-spicc: enhance output enable feature
The SPICC controller in Meson-AXG is capable of driving the CLK/MOSI/SS
signal lines through the idle state (between two transmission operation),
which avoid the signals floating in unexpected state.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Sunny Luo <sunny.luo@amlogic.com>
Link: https://lore.kernel.org/r/20200312133131.26430-3-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Neil Armstrong [Thu, 12 Mar 2020 13:31:23 +0000 (14:31 +0100)]
spi: meson-spicc: remove unused variables
Remove unused variables from spicc data struct.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200312133131.26430-2-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Dan Carpenter [Thu, 12 Mar 2020 11:31:54 +0000 (14:31 +0300)]
spi: spi-nxp-fspi: Fix a NULL vs IS_ERR() check in probe
The platform_get_resource_byname() function returns NULL on error, it
doesn't return error pointers.
Fixes:
d166a73503ef ("spi: fspi: dynamically alloc AHB memory")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200312113154.GC20562@mwanda
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Wed, 11 Mar 2020 19:58:20 +0000 (19:58 +0000)]
Merge tag 'mtk-mtd-spi-move' of https://git./linux/kernel/git/broonie/spi into spi-5.7
spi: Rewrite mtk-quadspi spi-nor driver with spi-mem
This patchset from Chuanhong Guo <gch981213@gmail.com> adds a spi-mem
driver for Mediatek SPI-NOR controller, which already has limited
support by mtk-quadspi. This new driver can make use of full quadspi
capability of this controller.
Chuanhong Guo [Fri, 6 Mar 2020 08:50:52 +0000 (16:50 +0800)]
mtd: spi-nor: remove mtk-quadspi driver
This driver is superseded by the new spi-mtk-nor driver.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200306085052.28258-5-gch981213@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Chuanhong Guo [Fri, 6 Mar 2020 08:50:51 +0000 (16:50 +0800)]
dt-bindings: convert mtk-quadspi binding doc for spi-mtk-nor
spi-mtk-nor is a driver to replace mtk-quadspi and they have almost
the same device-tree bindings. Reuse this binding documentation and
convert it for new driver:
1. "Mediatek SoCs" -> "Mediatek ARM SoCs" because MTK MIPS SoCs
use different controllers.
2. document "interrupts" as a required property because it's
available on all SoCs with this controller and new driver takes
advantages of it. It's implemented as optional only to maintain
backward compatibility.
3. add a dummy interrupt binding in example.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Link: https://lore.kernel.org/r/20200306085052.28258-4-gch981213@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Chuanhong Guo [Fri, 6 Mar 2020 08:50:50 +0000 (16:50 +0800)]
spi: add support for mediatek spi-nor controller
This is a driver for mtk spi-nor controller using spi-mem interface.
The same controller already has limited support provided by mtk-quadspi
driver under spi-nor framework and this new driver is a replacement
for the old one.
Comparing to the old driver, this driver has following advantages:
1. It can handle any full-duplex spi transfer up to 6 bytes, and
this is implemented using generic spi interface.
2. It take account into command opcode properly. The reading routine
in this controller can only use 0x03 or 0x0b as opcode on 1-1-1
transfers, but old driver doesn't implement this properly. This
driver checks supported opcode explicitly and use (1) to perform
unmatched operations.
3. It properly handles SFDP reading. Old driver can't read SFDP
due to the bug mentioned in (2).
4. It can do 1-2-2 and 1-4-4 fast reading on spi-nor. These two ops
requires parsing SFDP, which isn't possible in old driver. And
the old driver is only flagged to support 1-1-2 mode.
5. It takes advantage of the DMA feature in this controller for
long reads and supports IRQ on DMA requests to free cpu cycles
from polling status registers on long DMA reading. It achieves
up to 17.5MB/s reading speed (1-4-4 mode) which is way faster
than the old one. IRQ is implemented as optional to maintain
backward compatibility.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Link: https://lore.kernel.org/r/20200306085052.28258-3-gch981213@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Chuanhong Guo [Fri, 6 Mar 2020 08:50:49 +0000 (16:50 +0800)]
spi: make spi-max-frequency optional
We only need a spi-max-frequency when we specifically request a
spi frequency lower than the max speed of spi host.
This property is already documented as optional property and current
host drivers are implemented to operate at highest speed possible
when spi->max_speed_hz is 0.
This patch makes spi-max-frequency an optional property so that
we could just omit it to use max controller speed.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Link: https://lore.kernel.org/r/20200306085052.28258-2-gch981213@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
John Garry [Wed, 11 Mar 2020 17:35:15 +0000 (01:35 +0800)]
spi: Stop selecting MTD_SPI_NOR for SPI_HISI_SFC_V3XX
By selecting MTD_SPI_NOR for SPI_HISI_SFC_V3XX, we may introduce unmet
dependencies:
WARNING: unmet direct dependencies detected for MTD_SPI_NOR
Depends on [m]: MTD [=m] && SPI_MASTER [=y]
Selected by [y]:
- SPI_HISI_SFC_V3XX [=y] && SPI [=y] && SPI_MASTER [=y] && (ARM64 && ACPI [=y] || COMPILE_TEST [=y]) && HAS_IOMEM [=y]
Since MTD_SPI_NOR is only selected by SPI_HISI_SFC_V3XX for practical
reasons - slave devices use the spi-nor driver, enabled by MTD_SPI_NOR -
just drop it.
Signed-off-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1583948115-239907-1-git-send-email-john.garry@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Michael Walle [Tue, 10 Mar 2020 07:33:13 +0000 (08:33 +0100)]
spi: spi-fsl-dspi: fix DMA mapping
Use the correct device to request the DMA mapping. Otherwise the IOMMU
doesn't get the mapping and it will generate a page fault.
The error messages look like:
[ 3.008452] arm-smmu 5000000.iommu: Unhandled context fault: fsr=0x402, iova=0xf9800000, fsynr=0x3f0022, cbfrsynra=0x828, cb=8
[ 3.020123] arm-smmu 5000000.iommu: Unhandled context fault: fsr=0x402, iova=0xf9800000, fsynr=0x3f0022, cbfrsynra=0x828, cb=8
This was tested on a custom board with a LS1028A SoC.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200310073313.21277-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Tue, 10 Mar 2020 14:30:58 +0000 (14:30 +0000)]
Merge series "spi: Add FSI-attached SPI controller driver" from Eddie James <eajames@linux.ibm.com>:
This series adds a dts binding and a driver for a new SPI controller that is
accessed over FSI bus.
Eddie James (2):
dt-bindings: fsi: Add FSI2SPI bindings
spi: Add FSI-attached SPI controller driver
.../devicetree/bindings/fsi/ibm,fsi2spi.yaml | 36 ++
MAINTAINERS | 7 +
drivers/spi/Kconfig | 7 +
drivers/spi/Makefile | 1 +
drivers/spi/spi-fsi.c | 558 ++++++++++++++++++
5 files changed, 609 insertions(+)
create mode 100644 Documentation/devicetree/bindings/fsi/ibm,fsi2spi.yaml
create mode 100644 drivers/spi/spi-fsi.c
--
2.24.0
Qiujun Huang [Mon, 9 Mar 2020 17:16:19 +0000 (01:16 +0800)]
spi: update the structure documentation
some members were not described in documentation.
Signed-off-by: Qiujun Huang <hqjagain@gmail.com>
Link: https://lore.kernel.org/r/1583774179-30736-1-git-send-email-hqjagain@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Geert Uytterhoeven [Mon, 9 Mar 2020 17:15:37 +0000 (18:15 +0100)]
spi: rspi: Add support for active-high chip selects
All RSPI variants support setting the polarity of the SSL signal.
Advertize support for active-high chip selects, and configure polarity
according to the state of the flag.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200309171537.21551-1-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Johan Jonker [Mon, 9 Mar 2020 15:10:03 +0000 (16:10 +0100)]
spi: rockchip: add compatible string for px30 rk3308 rk3328
The Rockchip spi binding is updated to yaml and new models
were added. The spi on px30,rk3308 and rk3328 are the same as
other Rockchip based SoCs, so add compatible string for it.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200309151004.7780-1-jbx6244@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Eddie James [Fri, 6 Mar 2020 19:41:18 +0000 (13:41 -0600)]
spi: Add FSI-attached SPI controller driver
There exists a set of SPI controllers on some POWER processors that may
be accessed through the FSI bus. Add a driver to traverse the FSI CFAM
engine that can access and drive the SPI controllers. This driver would
typically be used by a baseboard management controller (BMC).
The SPI controllers operate by means of programming a sequencing engine
which automatically manages the usual SPI protocol buses. The driver
programs each transfer into the sequencer as various operations
specifying the slave chip and shifting data in and out on the lines.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20200306194118.18581-3-eajames@linux.ibm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Eddie James [Fri, 6 Mar 2020 19:41:17 +0000 (13:41 -0600)]
dt-bindings: fsi: Add FSI2SPI bindings
Add documentation for the FSI2SPI CFAM engine, which provides access to
a number of SPI controllers.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20200306194118.18581-2-eajames@linux.ibm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Joe Perches [Thu, 5 Mar 2020 15:15:53 +0000 (07:15 -0800)]
spi: Remove CONFIG_ prefix from Kconfig select
commit
a2ca53b52e00 ("spi: Add HiSilicon v3xx SPI NOR flash
controller driver") likely inadvertently used a select statement
with a CONFIG_ prefix, remove the prefix.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/f8ac6b32a29b9a05b58a7e58ffe8b780642abbf1.camel@perches.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Thu, 5 Mar 2020 14:36:28 +0000 (14:36 +0000)]
Merge series "TCFQ to XSPI migration for NXP DSPI driver" from Vladimir Oltean <olteanv@gmail.com>
Vladimir Oltean <vladimir.oltean@nxp.com>:
From: Vladimir Oltean <vladimir.oltean@nxp.com>
This series aims to remove the most inefficient transfer method from the
NXP DSPI driver.
TCFQ (Transfer Complete Flag) mode works by transferring one word,
waiting for its TX confirmation interrupt (or polling on the equivalent
status bit), sending the next word, etc, until the buffer is complete.
The issue with this mode is that it's fundamentally incompatible with
any sort of batching such as writing to a FIFO. But actually, due to
previous patchset ("Compatible string consolidation for NXP DSPI driver"):
https://patchwork.kernel.org/cover/
11414593/
all existing users of TCFQ mode today already support a more advanced
feature set, in the form of XSPI (extended SPI). XSPI brings 2 extra
features:
- Word sizes up to 32 bits. This is sub-utilized today, and acceleration
of smaller-than-32 bpw values is provided.
- "Command cycling", basically the ability to write multiple words in a
row and receiving an interrupt only after the completion of the last
one. This is what enables us to make use of the full FIFO depth of
this controller.
Series was tested on the NXP LS1021A-TSN and LS1043A-RDB boards, both
functionally as well as from a performance standpoint.
The command used to benchmark the increased throughput was:
spidev_test --device /dev/spidev1.0 --bpw 8 --size 256 --cpha --iter
10000000 --speed
20000000
where spidev1.0 is a dummy spidev node, using a chip select that no
peripheral responds to.
On LS1021A, which has a 4-entry-deep FIFO and a less powerful CPU, the
performance increase brought by this patchset is from 2700 kbps to 5800
kbps.
On LS1043A, which has a 16-entry-deep FIFO and a more powerful CPU, the
performance increases from 4100 kbps to 13700 kbps.
On average, SPI software timestamping is not adversely affected by the
extra batching, due to the extra patches.
There is one extra patch which clarifies why the TCFQ users were not
converted to the "other" mode in this driver that makes use of the FIFO,
which would be EOQ mode.
My request to the many people on CC (known users and/or contributors) is
to give this series a test to ensure there are no regressions, and for
the Coldfire maintainers to clarify whether the EOQ limitation is
acceptable for them in the long run.
Vladimir Oltean (12):
spi: spi-fsl-dspi: Simplify bytes_per_word gymnastics
spi: spi-fsl-dspi: Remove unused chip->void_write_data
spi: spi-fsl-dspi: Don't mask off undefined bits
spi: spi-fsl-dspi: Add comments around dspi_pop_tx and dspi_push_rx
functions
spi: spi-fsl-dspi: Rename fifo_{read,write} and {tx,cmd}_fifo_write
spi: spi-fsl-dspi: Implement .max_message_size method for EOQ mode
spi: Do spi_take_timestamp_pre for as many times as necessary
spi: spi-fsl-dspi: Convert TCFQ users to XSPI FIFO mode
spi: spi-fsl-dspi: Accelerate transfers using larger word size if
possible
spi: spi-fsl-dspi: Optimize dspi_setup_accel for lowest interrupt
count
spi: spi-fsl-dspi: Use EOQ for last word in buffer even for XSPI mode
spi: spi-fsl-dspi: Take software timestamp in dspi_fifo_write
drivers/spi/spi-fsl-dspi.c | 421 ++++++++++++++++++++++++-------------
drivers/spi/spi.c | 19 +-
include/linux/spi/spi.h | 3 +-
3 files changed, 288 insertions(+), 155 deletions(-)
--
2.17.1
Johan Jonker [Wed, 4 Mar 2020 18:42:03 +0000 (19:42 +0100)]
dt-bindings: spi: spi-rockchip: add description for rk3328
The description below is already in use for rk3328.dtsi,
but was somehow never added to a document, so add
"rockchip,rk3328-spi", "rockchip,rk3066-spi"
for spi nodes on a rk3328 platform to spi-rockchip.yaml.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200304184203.9548-3-jbx6244@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Johan Jonker [Wed, 4 Mar 2020 18:42:02 +0000 (19:42 +0100)]
dt-bindings: spi: spi-rockchip: add description for rk3308
The description below is already in use for rk3308.dtsi,
but was somehow never added to a document, so add
"rockchip,rk3308-spi", "rockchip,rk3066-spi"
for spi nodes on a rk3308 platform to spi-rockchip.yaml.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200304184203.9548-2-jbx6244@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Johan Jonker [Wed, 4 Mar 2020 18:42:01 +0000 (19:42 +0100)]
dt-bindings: spi: convert rockchip spi bindings to yaml
Current dts files with 'spi' nodes are manually verified.
In order to automate this process spi-rockchip.txt
has to be converted to yaml. In the new setup
spi-rockchip.yaml will inherit properties from
spi-controller.yaml.
Add document to MAINTAINERS.
Also rk3188.dtsi, rk3288.dtsi, rk3368.dtsi and rk3399.dtsi
use an extra fallback string, so change this in the documentation.
Changed:
"rockchip,rk3188-spi", "rockchip,rk3066-spi"
"rockchip,rk3288-spi", "rockchip,rk3066-spi"
"rockchip,rk3368-spi", "rockchip,rk3066-spi"
"rockchip,rk3399-spi", "rockchip,rk3066-spi"
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200304184203.9548-1-jbx6244@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Sascha Hauer [Thu, 5 Mar 2020 11:55:46 +0000 (12:55 +0100)]
spi: spi-fsl-dspi: Make bus-num property optional
The SPI bus number is completely optional to Linux, so make the
corresponding device tree property optional as well.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20200305115546.31814-1-s.hauer@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Adam Ford [Sun, 26 Jan 2020 14:09:11 +0000 (08:09 -0600)]
spi: spi-nxp-fspi: Add support for imx8mm, imx8qxp
Add support for nxp,imx8qxp-fspi and nxp,imx8mm-fspi do the bindings
document.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20200126140913.2139260-4-aford173@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Han Xu [Sun, 26 Jan 2020 14:09:10 +0000 (08:09 -0600)]
spi: spi-nxp-fspi: Enable the Octal Mode in MCR0
Apply patch from NXP upstream repo to
Enable the octal combination mode in MCR0
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20200126140913.2139260-3-aford173@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Han Xu [Sun, 26 Jan 2020 14:09:09 +0000 (08:09 -0600)]
spi: fspi: dynamically alloc AHB memory
Apply patch from NXP upstream repo to
dynamically allocate AHB memory as needed.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20200126140913.2139260-2-aford173@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Han Xu [Sun, 26 Jan 2020 14:09:08 +0000 (08:09 -0600)]
spi: fspi: enable fspi on imx8qxp and imx8mm
Pull in this patch from NXP's upstream repo to
enable fspi on imx8qxp and imx8mm
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20200126140913.2139260-1-aford173@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vladimir Oltean [Wed, 4 Mar 2020 22:00:44 +0000 (00:00 +0200)]
spi: spi-fsl-dspi: Take software timestamp in dspi_fifo_write
Although the SPI system timestamps are supposed to reflect the moment
that the peripheral has received a word rather than the moment when the
CPU has enqueued that word to the FIFO, in practice it is easier to just
record the latter time than the former (with a smaller error).
With the recent migration of TCFQ users from poll back to interrupt mode
(this time for XSPI FIFO), it's wiser to keep the interrupt latency
outside of the measurement of the PTP system timestamp itself. If there
proves to be any constant offset that requires static compensation, that
can always be added later. So far that does not appear to be the case at
least on the LS1021A-TSN board, where testing shows that the phc2sys
offset is able to remain within +/- 200 ns even after 68 hours of
testing.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200304220044.11193-13-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vladimir Oltean [Wed, 4 Mar 2020 22:00:43 +0000 (00:00 +0200)]
spi: spi-fsl-dspi: Use EOQ for last word in buffer even for XSPI mode
The EOQ mode has a hardware limitation in that it stops the transmission
(including the deassertion of the chip select signal) once the host CPU
requests end-of-queue for a particular word in the TX FIFO.
And XSPI mode has a limitation in that we need a separate CMD FIFO entry
for the last byte in the buffer, where the chip select signal needs to
be deasserted. It's not a functional limitation, but it's rather clunky
and the fact that we need to halt the pipeline and write a single entry
to the TX FIFO whenever a buffer ends brings the throughput down when
transmitting small buffers.
So the idea here is to use EOQ's limitation in our favor when using XSPI
mode. Stop special-casing that final word in the buffer, and just kill
the chip select signal by issuing an EOQ for that last word. Now it can
be mixed in with all the other words in the current TX FIFO train.
A small trick here is that we still keep using the XSPI-specific
signaling via the CMDTCFQ interrupt in RSER, and not enabling the EOQ
interrupt, in order to avoid hardware weirdness (potential races with
separate interrupts being raised for CMDTCFQ and EOQ for what is in fact
the end of the same transmission). That is just theoretical, but it's
good to be cautious, and the EOQ interrupt isn't needed.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200304220044.11193-12-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vladimir Oltean [Wed, 4 Mar 2020 22:00:42 +0000 (00:00 +0200)]
spi: spi-fsl-dspi: Optimize dspi_setup_accel for lowest interrupt count
Currently, a SPI transfer that is not multiple of the highest supported
word width (e.g. 4 bytes) will be transmitted as follows (assume a
30-byte buffer transmitted through a 32-bit wide FIFO that is 32 bytes
deep):
- First 28 bytes are sent as 7 words of 32 bits each
- Last 2 bytes are sent as 1 word of 16 bits size
But if the dspi_setup_accel function had decided to use a lower
oper_bits_per_word value (16 instead of 32), there would have been
enough space in the TX FIFO to fit the entire buffer in one go (15 words
of 16 bits each).
What we're actually trying to avoid is mixing word sizes within the same
run with the TX FIFO, since there is an erratum surrounding this, and
invalid data might get transmitted.
So this patch adds special cases for when the remaining length of the
buffer can be sent in one go as 8-bit or 16-bit words, otherwise it
falls back to the standard logic of sending as many bytes as possible at
the highest oper_bits_per_word value possible.
The benefit is that there will be one less CMDFQ/EOQ interrupt to
service when the entire buffer is transmitted during a single go, and
that will improve the overall latency of the transfer.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200304220044.11193-11-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vladimir Oltean [Wed, 4 Mar 2020 22:00:41 +0000 (00:00 +0200)]
spi: spi-fsl-dspi: Accelerate transfers using larger word size if possible
This patch adds logic in the driver to transmit SPI buffers that use
bits_per_word=8 with a higher bits_per_word count (multiple of 8).
Currently the following (most common) modes are implemented:
- 8 bits_per_word on 32-bit capable controllers
- 8 bits_per_word on 16-bit capable controllers
- 16 bits_per_word on 32-bit capable controllers
Transfers which are not accelerated are transferred with a hardware
bits_per_word value equal to the one of the SPI transfer.
The difference from just extending bits_per_word=32 at the spi_device
driver level is that endianness is different - the SPI core wants to
treat bits_per_word=32 buffers as arrays of u32 (i.e. words in host CPU
endianness). So to preserve endianness when clumping 8x4 bits into
32-bit words, one must perform conversion between CPU and standard (big)
endianness.
All appearances (both on the wire as well as in the buffers presented to
the peripheral driver) are preserved, just that accesses to the PUSHR
and POPR registers are now more efficient, since the same number of
reads/writes can now carry more data (2x more data on TX, 4x more data
on RX).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200304220044.11193-10-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vladimir Oltean [Wed, 4 Mar 2020 22:00:40 +0000 (00:00 +0200)]
spi: spi-fsl-dspi: Convert TCFQ users to XSPI FIFO mode
The Transfer Complete Flag (TCF) interrupt gets raised after each write
to the TX FIFO (PUSHR) which means that it is not possible to devise a
transfer procedure that makes full utilization of the FIFO depth (4
entries on most controllers, 16 entries on some).
On the other hand, XSPI mode has a feature called "command cycling",
which allows a single TX command to be run for a pre-specified number of
TX words. When the command cycle ends, the Command Transfer Complete
Flag bit asserts and raises an interrupt. The advantage in this mode is
that the TX FIFO can be better utilized (more words can be batched at
once).
Other changes brought by this patch:
- The dspi->rx_end variable has been removed, since now the
dspi_fifo_write function sets up dspi->words_in_flight, so
dspi_fifo_read knows how much to read without overrunning the RX
buffer.
- Stop using poll mode unconditionally for TCFQ mode, since XSPI mode
is a little less efficient than that, and so, poll mode doesn't bring
as many improvements for XSPI.
- Stop relying on the hardware transfer counter (SPI_TCR_GET_TCNT) and
instead increment the message->actual_length based on the newly
introduced dspi->words_in_flight variable.
- The CTARE register is now written in the hotpath instead of just at
transfer init time, since it contains the DTCP field (transfer
preload - the counter indicating how many txdata words will follow),
which is a dynamic value.
Due to the fact that the Chip Select toggling setting is part of the
command written to the TX FIFO, the ending word of each buffer needs to
be sent via its own TX command, so that we have a chance to emit a
1-word command with deasserted PCS.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200304220044.11193-9-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vladimir Oltean [Wed, 4 Mar 2020 22:00:39 +0000 (00:00 +0200)]
spi: Do spi_take_timestamp_pre for as many times as necessary
When dealing with a SPI controller driver that is sending more than 1
byte at once (or the entire buffer at once), and the SPI peripheral
driver has requested timestamping for a byte in the middle of the
buffer, we find that spi_take_timestamp_pre never records a "pre"
timestamp.
This happens because the function currently expects to be called with
the "progress" argument >= to what the peripheral has requested to be
timestamped. But clearly there are cases when that isn't going to fly.
And since we can't change the past when we realize that the opportunity
to take a "pre" timestamp has just passed and there isn't going to be
another one, the approach taken is to keep recording the "pre" timestamp
on each call, overwriting the previously recorded one until the "post"
timestamp is also taken.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200304220044.11193-8-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vladimir Oltean [Wed, 4 Mar 2020 22:00:38 +0000 (00:00 +0200)]
spi: spi-fsl-dspi: Implement .max_message_size method for EOQ mode
When it gets set, End Of Queue Flag halts the DSPI controller and forces
the chip select signal to deassert.
This operating mode is not ideal, but it is used for the DSPI
instantiations where there is no other notification from the controller
that the data in the FIFO has finished transmission. So in practice, it
means that transmitting buffers larger than the FIFO size will yield
unpredictable results.
The only controller that operates in EOQ mode is MCF5441X (Coldfire). I
would say that the way EOQ is used (and documented in the reference
manual, too) on this chip is incorrect, and I would personally migrate
it to TCFQ, but that's notably worse in terms of performance (it can
only use 1 entry of the 16-deep FIFO) and if this limitation didn't
bother any Coldfire DSPI user so far, it's likely that we just need to
throw an error for larger buffers to make sure that callers are aware
their transfers are getting truncated/split.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200304220044.11193-7-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vladimir Oltean [Wed, 4 Mar 2020 22:00:37 +0000 (00:00 +0200)]
spi: spi-fsl-dspi: Rename fifo_{read,write} and {tx,cmd}_fifo_write
These function names are very generic and it is easy to get confused.
Rename them after the hardware register that they are accessing.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200304220044.11193-6-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vladimir Oltean [Wed, 4 Mar 2020 22:00:36 +0000 (00:00 +0200)]
spi: spi-fsl-dspi: Add comments around dspi_pop_tx and dspi_push_rx functions
Their names are confusing, since dspi_pop_tx prepares a word to be
written to the PUSHR register, and dspi_push_rx gets a word from the
POPR register.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200304220044.11193-5-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vladimir Oltean [Wed, 4 Mar 2020 22:00:35 +0000 (00:00 +0200)]
spi: spi-fsl-dspi: Don't mask off undefined bits
This is a useless operation, and if the driver needs to do that, there's
something deeply wrong going on.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200304220044.11193-4-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vladimir Oltean [Wed, 4 Mar 2020 22:00:34 +0000 (00:00 +0200)]
spi: spi-fsl-dspi: Remove unused chip->void_write_data
This variable has been present since the initial submission of the
driver, and held, for some reason, the value of zero, to be sent on the
wire in the case there wasn't any TX buffer for the current transfer.
Since quite a while now, however, it isn't doing anything at all.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200304220044.11193-3-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vladimir Oltean [Wed, 4 Mar 2020 22:00:33 +0000 (00:00 +0200)]
spi: spi-fsl-dspi: Simplify bytes_per_word gymnastics
Reduce the if-then-else-if-then-else sequence to:
- a simple division in the case of bytes_per_word calculation
- a memcpy command with a variable size. The semantics of larger-than-8
xfer->bits_per_word is that those words are to be interpreted and
transmitted in CPU native endianness.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200304220044.11193-2-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Wed, 4 Mar 2020 18:28:57 +0000 (18:28 +0000)]
Merge series "Compatible string consolidation for NXP DSPI driver" from Vladimir Oltean <olteanv@gmail.com>:
This series makes room in the driver for differentiation between the
controllers which currently operate in TCFQ mode. Most of these are
actually capable of a lot more in terms of throughput. This is in
preparation of a second series which will convert the remaining users of
TCFQ mode altogether to XSPI mode with command cycling.
Vladimir Oltean (6):
doc: spi-fsl-dspi: Add specific compatibles for all Layerscape SoCs
spi: spi-fsl-dspi: Use specific compatible strings for all SoC
instantiations
spi: spi-fsl-dspi: Parameterize the FIFO size and DMA buffer size
spi: spi-fsl-dspi: LS2080A and LX2160A support XSPI mode
spi: spi-fsl-dspi: Support SPI software timestamping in all non-DMA
modes
spi: spi-fsl-dspi: Convert the instantiations that support it to DMA
.../devicetree/bindings/spi/spi-fsl-dspi.txt | 17 +-
drivers/spi/spi-fsl-dspi.c | 162 +++++++++++++-----
2 files changed, 128 insertions(+), 51 deletions(-)
--
2.17.1
Vladimir Oltean [Mon, 2 Mar 2020 00:19:53 +0000 (02:19 +0200)]
spi: spi-fsl-dspi: Add specific compatibles for all Layerscape SoCs
Make the second compatible string optional for LS1012A, LS1088A and
LS2080A. Old versions of the spi-fsl-dspi.c driver still need to probe
on the old, generic compatible string for these controllers (such as
"fsl,ls1021a-v1.0-dspi") which provides less functionality.
Document the device tree bindings for LS1043A and LS1046A, whose
bindings are already in use in fsl-ls1043a.dtsi and fsl-ls1046a.dtsi.
Introduce new compatible strings for LS1028A and LX2160A. There will be
no second compatible string for these.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-Id: <
20200302001958.11105-2-olteanv@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Vladimir Oltean [Mon, 2 Mar 2020 00:19:58 +0000 (02:19 +0200)]
spi: spi-fsl-dspi: Convert the instantiations that support it to DMA
The A-011218 eDMA/DSPI erratum affects most of the older Layerscape SoCs
with DSPI, and its workaround is a bit intrusive.
After this patch, there are no users of TCFQ mode that don't also
support XSPI (previously there was LS2085A).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-Id: <
20200302001958.11105-7-olteanv@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Vladimir Oltean [Mon, 2 Mar 2020 00:19:57 +0000 (02:19 +0200)]
spi: spi-fsl-dspi: Support SPI software timestamping in all non-DMA modes
There's no reason to keep this .ptp_sts_supported property explicitly in
devtype_data, since it can be deduced from the operating mode alone.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-Id: <
20200302001958.11105-6-olteanv@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Vladimir Oltean [Mon, 2 Mar 2020 00:19:56 +0000 (02:19 +0200)]
spi: spi-fsl-dspi: LS2080A and LX2160A support XSPI mode
XSPI allows for 2 extra features:
- Command cycling (use a single TX command with more than 1 word in the
TX FIFO).
- Increased word size (from 16 bits to 32 bits)
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-Id: <
20200302001958.11105-5-olteanv@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Vladimir Oltean [Mon, 2 Mar 2020 00:19:55 +0000 (02:19 +0200)]
spi: spi-fsl-dspi: Parameterize the FIFO size and DMA buffer size
Get rid of the ifdef for Coldfire and make these hardware
characteristics part of dspi->devtype_data.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-Id: <
20200302001958.11105-4-olteanv@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Vladimir Oltean [Mon, 2 Mar 2020 00:19:54 +0000 (02:19 +0200)]
spi: spi-fsl-dspi: Use specific compatible strings for all SoC instantiations
Currently, the device tree bindings submitted in mainline for Layerscape
SoCs look like this:
LS1021A:
compatible = "fsl,ls1021a-v1.0-dspi";
LS1012A:
compatible = "fsl,ls1012a-dspi", "fsl,ls1021a-v1.0-dspi";
LS2085A:
compatible = "fsl,ls2085a-dspi";
LS2088A:
compatible = "fsl,ls2080a-dspi", "fsl,ls2085a-dspi";
LX2160A:
compatible = "fsl,lx2160a-dspi", "fsl,ls2085a-dspi";
LS1043A:
compatible = "fsl,ls1043a-dspi", "fsl,ls1021a-v1.0-dspi";
LS1046A:
compatible = "fsl,ls1021a-v1.0-dspi";
Due to a lack of a more specific compatible string, LS1012A, LS1043A and
LS1046A will fall under the LS1021A umbrella, and LS2088A and LX2160A
under the LS2085A umbrella.
They do work in those modes, but there are slight differences in the
hardware instantiations, mostly related to FIFO sizes (with the more
specific compatible strings, the FIFO size can be increased properly).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-Id: <
20200302001958.11105-3-olteanv@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Linus Torvalds [Tue, 3 Mar 2020 23:31:19 +0000 (17:31 -0600)]
Merge tag '5.6-rc4-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Five small cifs/smb3 fixes, two for stable (one for a reconnect
problem and the other fixes a use case when renaming an open file)"
* tag '5.6-rc4-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Use #define in cifs_dbg
cifs: fix rename() by ensuring source handle opened with DELETE bit
cifs: add missing mount option to /proc/mounts
cifs: fix potential mismatch of UNC paths
cifs: don't leak -EAGAIN for stat() during reconnect
Mark Brown [Tue, 3 Mar 2020 14:47:19 +0000 (14:47 +0000)]
Merge series "trivial fixes for fsl-spi and spidev" from Oleksandr Suvorov <oleksandr.suvorov@toradex.com>:
- the memory optimization in fsl-spi
- the fix of the max speed setting bug in spidev
Oleksandr Suvorov (2):
spi: fsl-lpspi: remove unneeded array
spi: spidev: fix a max speed setting
drivers/spi/spi-fsl-lpspi.c | 7 ++-----
drivers/spi/spidev.c | 10 ++++++----
2 files changed, 8 insertions(+), 9 deletions(-)
--
2.24.1
Oleksandr Suvorov [Thu, 20 Feb 2020 14:11:48 +0000 (14:11 +0000)]
spi: fsl-lpspi: remove unneeded array
- replace the array with the shift operation
- remove the extra comparing operation.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Link: https://lore.kernel.org/r/20200220141143.3902922-2-oleksandr.suvorov@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Anson Huang [Tue, 3 Mar 2020 13:44:12 +0000 (21:44 +0800)]
regulator: anatop: Lower error message level for -EPROBE_DEFER
devm_regulator_register() could return -EPROBE_DEFER when trying to
get init data and NOT all resources are available at that time, for
this case, error message is better to be present for debug level ONLY.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Link: https://lore.kernel.org/r/1583243052-1930-1-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Mon, 2 Mar 2020 15:19:59 +0000 (15:19 +0000)]
Merge series "spi: spidev: Fix messages in spidev" from Oleksandr Suvorov <oleksandr.suvorov@toradex.com>:
- fix the values source for the xfer debug message.
- fix the "max speed setting" message showing.
Oleksandr Suvorov (2):
spi: spidev: fix a debug message value
spi: spidev: fix speed setting message
drivers/spi/spidev.c | 23 ++++++++++++-----------
1 file changed, 12 insertions(+), 11 deletions(-)
--
2.24.1
Oleksandr Suvorov [Sat, 29 Feb 2020 16:18:41 +0000 (18:18 +0200)]
spi: spidev: fix speed setting message
The message of max device speed setting is shown when
an error in spi_setup() occurs.
Instead, it should be shown when the setup call succeeds.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Link: https://lore.kernel.org/r/20200229161841.89144-3-oleksandr.suvorov@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Oleksandr Suvorov [Sat, 29 Feb 2020 16:18:40 +0000 (18:18 +0200)]
spi: spidev: fix a debug message value
The debug message in spidev_message() can show wrong xfer speed.
It happens if the initial (came from DT) and set with ioctl call spidev
speeds are different (spidev->speed_hz != spi->max_speed_hz) and one
sends a message with ioctl call and the field of speed is uninitialized
(u_tmp->speed_hz == 0).
In this case the kernel shows the spi->max_speed_hz value instead of
correct spidev->speed_hz.
...
set the max speed with an ioctl call:
[ 1227.702714] spidev spi0.0: setup mode 0, 32 bits/w,
20000000 Hz max --> 0
(real speed sets to 20000000Hz)
send a message with an ioctl call:
[ 1227.731801] spidev spi0.0: xfer len 4096 tx 32bits 0 usec 10000000Hz
(debug message shows 10000000Hz that is the original max speed of this
spidev came from DT)
...
Fix the data source for the debug message.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Link: https://lore.kernel.org/r/20200229161841.89144-2-oleksandr.suvorov@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Christophe JAILLET [Fri, 28 Feb 2020 21:38:38 +0000 (22:38 +0100)]
spi: bcm63xx-hsspi: Really keep pll clk enabled
The purpose of commit
0fd85869c2a9 ("spi/bcm63xx-hsspi: keep pll clk enabled")
was to keep the pll clk enabled through the lifetime of the device.
In order to do that, some 'clk_prepare_enable()'/'clk_disable_unprepare()'
calls have been added in the error handling path of the probe function, in
the remove function and in the suspend and resume functions.
However, a 'clk_disable_unprepare()' call has been unfortunately left in
the probe function. So the commit seems to be more or less a no-op.
Axe it now, so that the pll clk is left enabled through the lifetime of
the device, as described in the commit.
Fixes:
0fd85869c2a9 ("spi/bcm63xx-hsspi: keep pll clk enabled")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://lore.kernel.org/r/20200228213838.7124-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Jon Hunter [Mon, 2 Mar 2020 14:14:28 +0000 (14:14 +0000)]
regulator: pwm: Don't warn on probe deferral
Deferred probe is an expected return value for devm_pwm_get(). Given
that the driver deals with it properly, rather than warn on probe
deferral, only output a message on probe deferral if debug level
prints are enabled.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20200302141428.14119-1-jonathanh@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Anson Huang [Mon, 2 Mar 2020 11:55:18 +0000 (19:55 +0800)]
regulator: anatop: Improve Kconfig dependency
ANATOP regulator should depend on ARCH_MXC or COMPILE_TEST.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Link: https://lore.kernel.org/r/1583150118-8014-1-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Linus Torvalds [Mon, 2 Mar 2020 12:54:54 +0000 (06:54 -0600)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Misc fixes: a pkeys fix for a bug that triggers with weird BIOS
settings, and two Xen PV fixes: a paravirt interface fix, and
pagetable dumping fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Fix dump_pagetables with Xen PV
x86/ioperm: Add new paravirt function update_io_bitmap()
x86/pkeys: Manually set X86_FEATURE_OSPKE to preserve existing changes
Linus Torvalds [Mon, 2 Mar 2020 12:51:43 +0000 (06:51 -0600)]
Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull scheduler fix from Ingo Molnar:
"Fix a scheduler statistics bug"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Fix statistics for find_idlest_group()
Linus Torvalds [Mon, 2 Mar 2020 12:46:39 +0000 (06:46 -0600)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"No kernel side changes, all tooling fixes plus two tooling cleanups
that were committed late in the merge window alongside the perf
annotate fixes, delayed by Arnaldo's European trip"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
perf annotate: Fix segfault with source toggle
perf annotate: Align struct annotate_args
perf annotate: Simplify disasm_line allocation and freeing code
perf annotate: Remove privsize from symbol__annotate() args
perf probe: Check return value of strlist__add() for -ENOMEM
perf config: Document missing config options
perf annotate: Fix perf config option description
perf annotate: Prefer cmdline option over default config
perf annotate: Make perf config effective
perf config: Introduce perf_config_u8()
perf annotate: Fix --show-nr-samples for tui/stdio2
perf annotate: Fix --show-total-period for tui/stdio2
perf annotate/tui: Re-render title bar after switching back from script browser
tools headers UAPI: Update tools's copy of kvm.h headers
tools arch x86: Sync the msr-index.h copy with the kernel sources
perf arch powerpc: Sync powerpc syscall.tbl with the kernel sources
perf auxtrace: Add auxtrace_record__read_finish()
perf arm-spe: Fix endless record after being terminated
perf cs-etm: Fix endless record after being terminated
perf intel-bts: Fix endless record after being terminated
...
Linus Torvalds [Mon, 2 Mar 2020 12:41:41 +0000 (06:41 -0600)]
Merge branch 'efi-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull EFI fixes from Ingo Molnar:
"Three fixes to EFI mixed boot mode, mostly related to x86-64 vmap
stacks activated years ago, bug-fixed recently for EFI, which had
knock-on effects of various 1:1 mapping assumptions in mixed mode.
There's also a READ_ONCE() fix for reading an mmap-ed EFI firmware
data field only once, out of caution"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: READ_ONCE rng seed size before munmap
efi/x86: Handle by-ref arguments covering multiple pages in mixed mode
efi/x86: Remove support for EFI time and counter services in mixed mode
efi/x86: Align GUIDs to their size in the mixed mode runtime wrapper
Linus Torvalds [Sun, 1 Mar 2020 22:38:46 +0000 (16:38 -0600)]
Linux 5.6-rc4
Linus Torvalds [Sun, 1 Mar 2020 22:35:08 +0000 (16:35 -0600)]
Merge tag 'ext4_for_linus_stable' of git://git./linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Two more bug fixes (including a regression) for 5.6"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: potential crash on allocation error in ext4_alloc_flex_bg_array()
jbd2: fix data races at struct journal_head