upstream: [media] cx23885: remove g_chip_ident

Replace g_chip_ident by g_chip_info. Note that the IR support is implemented
as a subdev, so this part no longer needs to be handled as a 'bridge' chip.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] ivtv: remove g_chip_ident

g_chip_ident was used to determine if a saa7114 or saa7115 was used. Instead
just check the subdev name.
After that the g_chip_ident function can be removed.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] saa7115: add back the dropped 'found' message

The saa7115 driver used to show a 'chip found' message during probe. This
was accidentally dropped during recent commits. Add it back as it is quite
useful.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] cx18: remove g_chip_ident support

The av-core is really a subdev, so there is no need anymore to act as if it
is a 'second' bridge chip.
As a result of this the g_chip_ident implementation can be completely dropped.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] v4l2: remove g_chip_ident from bridge drivers where it is easy to do so

VIDIOC_DBG_G_CHIP_IDENT has been replaced by VIDIOC_DBG_G_CHIP_INFO. Remove
g_chip_ident support from bridge drivers since it is no longer needed.
This patch takes care of all the trivial cases.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] v4l2-ioctl: dbg_g/s_register: only match BRIDGE and SUBDEV types

Drop support for V4L2_CHIP_MATCH_I2C_DRIVER/ADDR and V4L2_CHIP_MATCH_AC97
types. The following patches will remove support for those in the drivers
as well.
This means that bridge drivers no longer have to check for the match.type
field in their g/s_register implementations. Only if they also implement
g_chip_info do they still have to check the match.addr field, otherwise the
core will check for that as well.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] media: i2c: ths7303: make the pdata as a constant pointer

generally the pdata needs to be a constant pointer in the device
state structure. This patch makes the pdata as a constant pointer
and alongside returns -EINVAL when pdata is NULL.

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] media: i2c: ths7303: remove unnecessary function ths7303_setup()

the ths7303_setup() was doing the same thing as ths7303_setval()
except that ths7303_setval() sets it to some particular mode.
This patch removes ths7303_setup() function and calls ths7303_setval()
in the probe setting the device to 480I_576I filter mode in the probe.

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] media: i2c: ths7303: remove init_enable option from pdata

This patch removes init_enable option from pdata, the init_enable
was intended that the device should start streaming video immediately
but ideally the bridge drivers should call s_stream explicitly for such
devices to start video.

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] radio-keene: add delay in order to settle hardware

It was found by trial and error testing that at least 11 ms delay is
needed before first I/O, otherwise device will skip given command.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] radio-keene: set initial frequency

The device was never set to the initial frequency.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] ml86v7667: fix the querystd implementation

The *std should be set to V4L2_STD_UNKNOWN, not the function's return code.
Also, *std should be ANDed with 525_60 or 625_50.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] ML86V7667: new video decoder driver

Add OKI Semiconductor ML86V7667 video decoder driver.
[Sergei: added v4l2_device_unregister_subdev() call to the error cleanup path
of ml86v7667_probe(), renamed ml86v7667_try_mbus_fmt() to ml86v7667_mbus_fmt(),
killed v4l2_chip_match_i2c_client() checks in the [gs]_register() methods, fixed
the prototype of the s_register() method, did some cleanup.]

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] adv7180: add more subdev video ops

Add subdev video ops for ADV7180 video decoder.  This makes decoder usable on
the soc-camera drivers.
[Sergei: renamed adv7180_try_mbus_fmt() to adv7180_mbus_fmt().]

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] hdpvr: improve error handling

get_video_info() should never return EFAULT, instead it should return
the low-level usb_control_msg() error. Add a valid field to the hdpvr_video_info
struct so the driver can easily check if a valid format was detected.
Whenever get_video_info is called and it returns an error (e.g. usb_control_msg
failed), then return that error to userspace as well.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] hdpvr: code cleanup

Remove an unnecessary 'else' and invert a condition which makes the code
more readable.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] hdpvr: fix querystd 'unknown format' return

If no format has been detected, then querystd should return V4L2_STD_UNKNOWN,
not V4L2_STD_ALL.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] smscoreapi: memory leak fix

Ensure release_firmware is called if kmalloc fails.

[mchehab@redhat.com: patch unmangled and converted from -p2 to -p1]
Signed-off-by: Roberto Alcantara <roberto@eletronica.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] s5c73m3: Fix whitespace related warnings

Silences the following type of warning:
WARNING: space prohibited before semicolon

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] s3c-camif: Use dev_info instead of printk

dev_info is preferred to printk. Silences the related checkpatch
warning.
WARNING: Prefer netdev_info(netdev, ... then dev_info(dev, ...
then pr_info(...  to printk(KERN_INFO ...

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] s3c-camif: Staticize local symbols

These symbols are local to the file and should be static.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] media: info leak in __media_device_enum_links()

These structs have holes and reserved struct members which aren't
cleared.  I've added a memset() so we don't leak stack information.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] omap3isp: ccp2: Don't ignore the regulator_enable() return value

Check the return value and catch errors correctly.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] omap3isp: include linux/mm_types.h

The ispqueue.h file uses vm_flags_t, which is defined in
linux/mm_types.h, so we must include that header in order
to build in all configurations.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] omap3isp: Remove redundant platform_set_drvdata()

Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: firewire: introduce fw_driver.probe and .remove methods

FireWire upper layer drivers are converted from generic
    struct driver.probe() and .remove()
to bus-specific
    struct fw_driver.probe() and .remove().

The new .probe() adds a const struct ieee1394_device_id *id argument,
indicating the entry in the driver's device identifiers table which
matched the fw_unit to be probed.  This new argument is used by the
snd-firewire-speakers driver to look up device-specific parameters and
methods.  There is at least one other FireWire audio driver currently in
development in which this will be useful too.

The new .remove() drops the unused error return code.

Although all in-tree drivers are being converted to the new methods,
support for the old methods is left in place in this commit.  This
allows public developer trees to merge this commit and then move to the
new fw_driver methods.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Clemens Ladisch <clemens@ladisch.de> (for sound/firewire/)
Cc: Peter Hurley <peter@hurleysoftware.com> (for drivers/staging/fwserial/)

upstream: [media] rtl28xxu: map remote for TerraTec Cinergy T Stick Black

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] rtl28xxu: correct some device names

... just because I want to be perfect ;)

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] rtl28xxu: Add USB ID for Leadtek WinFast DTV Dongle mini

USB ID 0413:6a03 is Leadtek WinFast DTV Dongle mini.
Decoder Realtek RTL2832U and tuner Infineon TUA9001.

Signed-off-by: Miroslav Šustek <sustmidown@centrum.cz>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] af9035: correct TS mode handling

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] af9035: minor log writing changes

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] af9035: make checkpatch.pl happy!

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] af9035: implement I2C adapter read operation

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] Add support for 'Digital Dual TV Receiver CTVDIGDUAL v2

Tested on a MIPSel box with 3.3.6 kernel
The kernel output when the device will be detected follows:
usbcore: registered new interface driver dvb_usb_it913x
it913x: Chip Version=01 Chip Type=9135
it913x: Remote propriety (raw) mode
it913x: Dual mode=3 Tuner Type=38
it913x: Chip Version=01 Chip Type=9135
usb 2-1: dvb_usb_v2: found a 'Digital Dual TV Receiver CTVDIGDUAL_V2' in cold state
usb 2-1: dvb_usb_v2: downloading firmware from file 'dvb-usb-it9137-01.fw'
it913x: FRM Starting Firmware Download
it913x: FRM Firmware Download Completed - Resetting Device
it913x: Chip Version=01 Chip Type=9135
it913x: Firmware Version 204147968
usb 2-1: dvb_usb_v2: found a 'Digital Dual TV Receiver CTVDIGDUAL_V2' in warm state
usb 2-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
DVB: registering new adapter (Digital Dual TV Receiver CTVDIGDUAL_V2)
it913x-fe: ADF table value      :00
it913x-fe: Crystal Frequency :12000000 Adc Frequency :20250000 ADC X2: 00
it913x-fe: Tuner LNA type :38
usb 2-1: DVB: registering adapter 1 frontend 0 (Digital Dual TV Receiver CTVDIGDUAL_V2_1)...
usb 2-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
DVB: registering new adapter (Digital Dual TV Receiver CTVDIGDUAL_V2)
it913x-fe: ADF table value      :00
it913x-fe: Crystal Frequency :12000000 Adc Frequency :20250000 ADC X2: 00
it913x-fe: Tuner LNA type :38
usb 2-1: DVB: registering adapter 2 frontend 0 (Digital Dual TV Receiver CTVDIGDUAL_V2_2)...
usb 2-1: dvb_usb_v2: 'Digital Dual TV Receiver CTVDIGDUAL_V2' successfully initialized and connected
RC part not tested

Signed-off-by: Alessandro Miceli <angelofsky1980@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] stb0899: sign of CRL_FREQ doesn't depend on inversion

Contrary to CFR (derotator frequency), which changes signedness
depending on inversion, CRL_FREQ does not.

Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] stb0899: use autodetected inversion instead of configured inversion

For consistency, it is necessary to use the autodetected inversion
instead of the configured one.

Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] stb0899: store autodetected inversion while tuning in non S2 mode

In non S2 mode, the device is able to autodetect inversion. So
let's store it for tuning to S2 transponders.

Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] stb0899: store successful inversion for next run

Usually, inversion doesn't change in a system. Storing the last
successful inversion value speeds up tuning of DVB-S2 transponders.

Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] stb0899: allow minimum symbol rate of 2000000

Looks like product datasheets for tuners containing STB0899 are
suggesting specification for min. symbol rate of 2MS/s.
Some specs found here, all suggesting 2MS/s for min. symbol rate:
    Comtech DVBS2-6899
      http://comtech.sg1002.myweb.hinet.net/pdf/dvbs2-6899.pdf
    TechniSat SkyStar HD2
      http://www.scaistar.com/skystar2/skystarhd2.htm
    Azurewave AD-SP400
      http://www.pulsat.com/products/AzureWave-AD%252dSP400-High-Definition-PC-Card.html
New patch:
This makes minimum symbol rate driver capabilities on par with some
accessible datasheet specifications*, and allows tuning on linux to
transponders that have symbol rate between 2000000-5000000, too.
Patch was tested successfully on Eutelsat 16A transponders that
became reachable with it (2000000 < symbol rate < 5000000):
      * DVB/S  12507050 V  2532000 3/4
      * DVB/S2 12574000 V  4355000 3/4 8PSK
      * DVB/S  12593000 V  2500000 2/3
      * DVB/S  12596940 V  2848000 2/3
      * DVB/S  12600750 V  2500000 1/2
      * DVB/S  12675590 H  4248000 3/4
(*) Datasheet: http://comtech.sg1002.myweb.hinet.net/pdf/dvbs2-6899.pdf
        Maximum Symbol Rate
        QPSK/LDPC/PCH: 20-30Mbps
        8PSK/LDPC/BCH: 10-30Mbps
        DVB: 2-45Mbps
             ^--------- min. symbol rate

Signed-off-by: Zoran Turalija <zoran.turalija@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] stb0899: fix inversion enum values to match usage with CFR

Throughout the zig-zag-implementations, inversion is taken into
account when reading and writing the CFR register, which contains
the derotator frequency. As swapping IQ signals changes the sign
of that register for example, the idea is to compensate that sign
change by multiplying the register value with the inversion enum
value.
The current enum values 0 and 1 for IQ_SWAP_OFF and IQ_SWAP_ON
don't work in the case IQ_SWAP_OFF, due to the multiplication by
zero (I've only found a single device which actually uses
IQ_SWAP_OFF in it's config).
I've changed the enum values to +1 and -1 to accommodate to the
intended usage.

Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] stb0899: enable auto inversion handling unconditionally

It seems that current inversion handling addresses only the signal
routing on the PCB, i. e. IQ signals are either swapped or not.
But when the device is operated in a Satellite Channel Router (SCR)
environment, an additional inversion is required due to the way how
the SCR works. Therefore it makes sense to me to always enable auto
inversion handling and drop the enum value IQ_SWAP_AUTO.

Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] stb0899: allow minimum symbol rate of 1000000

This makes minimum symbol rate driver capabilities on par with
windows driver, and allows tuning on linux to transponders that
have symbol rate below 5000000, too.
Patch was tested successfully on Eutelsat 16A transponders that
became reachable with it (1000000 < symbol rate < 5000000):
      * DVB/S  12507050 V  2532000 3/4
      * DVB/S2 12574000 V  4355000 3/4 8PSK
      * DVB/S  12593000 V  2500000 2/3
      * DVB/S  12596940 V  2848000 2/3
      * DVB/S  12600750 V  2500000 1/2
      * DVB/S  12675590 H  4248000 3/4

Signed-off-by: Zoran Turalija <zoran.turalija@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] stb0899: sign extend raw CRL_FREQ value

Contrary to the chip's specs, the register's value is signed, so we
need to sign extend the value before using it in calculations like
when determining the offset frequency.

Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] r820t: do not double-free fe->tuner_priv in r820t_release()

fe->tuner_priv is already freed by hybrid_tuner_release_state().

Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] dib8000: Fix dib8000_set_frontend() never setting ret

drivers/media/dvb-frontends/dib8000.c: In function ‘dib8000_set_frontend’:
drivers/media/dvb-frontends/dib8000.c:3556: warning: ‘ret’ is used uninitialized in this function
Remove the variable and return zero instead.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] uvcvideo: Fix open/close race condition

Maintaining the users count using an atomic variable makes sure that
access to the counter won't be racy, but doesn't serialize access to the
operations protected by the counter. This creates a race condition that
could result in the status URB being submitted multiple times.
Use a mutex to protect the users count and serialize access to the
status start and stop operations.

Reported-by: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] uvcvideo: quirk PROBE_DEF for Alienware X51 OmniVision webcam

BugLink: http://bugs.launchpad.net/bugs/1180409
OminiVision webcam 0x05a9:0x2643 needs the same UVC_QUIRK_PROBE_DEF
as other OmniVision models to work properly.

Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] uvcvideo: quirk PROBE_DEF for Dell Studio / OmniVision webcam

BugLink: https://bugs.launchpad.net/bugs/1168430
OminiVision webcam 0x05a9:0x264a (in Dell Studio Hybrid 140g) needs the
same UVC_QUIRK_PROBE_DEF as other OmniVision model to be recognized
consistently.

Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] coda: do not call v4l2_m2m_job_finish from .job_abort

If we just declare the job finished here while the CODA is still
running, the call to v4l2_m2m_ctx_release in coda_release, which
is supposed to wait for a running job to finish, will return
immediately and free memory that the CODA is still using.
Just set the 'aborting' flag and let coda_irq_handler deal with it.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] coda: replace completion with mutex

Not only do we need to wait for job completion when we want to
call a command on the CODA in start/stop_streaming, we also need
to make sure that a new job doesn't start before the command
finished.
Use a mutex to lock the coda command handling. On timeout, the
device_run job must be marked as finished and the mutex released,
as otherwise coda_release will block.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] coda: add coda_encode_header helper function

In preparation for CODA7541 and CODA960 multi-stream support and for
replacement of the completion with a mutex lock, consolidate the
header encoding in a helper function.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] coda: per-product list of codecs instead of list of formats

This patch adds a list of supported codecs per device type which is used to
determine the allowed pixel formats and maximum frame sizes depending on the
possible codecs. It allows frame sizes larger than 720 x 576 on CODA7 and adds
support for the YVU420 (planar YUV 4:2:0 with switched Cb and Cr) format.
Other uncompressed formats that could be added in the future are the chroma
interleaved NV12 and NV21 formats and the multiplanar variants YUV420M,
YVU420M, NV12M, and NV21M.
Further, rawstreamon is renamed to streamon_out and compstreamon is renamed
to streamon_cap in preparation for decoding support. The maximum encoded
frame buffer size is increased to 1 MiB.
Instead of tracking inst_type and codec across S_FMT calls, set the codec
and inst_type in start_streaming.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] coda: simplify parameter buffer setup code

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: Documentation/DocBook/media/v4l fix a typo

Corrected the word adjactent to adjacent.

Signed-off-by: Stefan Huber <steffhip@googlemail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

upstream: Finally eradicate CONFIG_HOTPLUG

Ever since commit 45f035ab9b8f ("CONFIG_HOTPLUG should be always on"),
it has been basically impossible to build a kernel with CONFIG_HOTPLUG
turned off.  Remove all the remaining references to it.

Cc: Russell King <linux@arm.linux.org.uk>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

upstream: [media] coda: clear registers in coda_hw_init

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] coda: stop setting bytesused in buf_prepare

The application must have filled the bytesused field,
don't overwrite it here.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] coda: frame stride must be a multiple of 8

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] coda: fix ENC_SEQ_OPTION for CODA7

GAMMA_OFFSET is different between CodaDx6 and CODA7.
Also, this is a bitfield.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: doc: fix misspellings with 'codespell' tool

Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

upstream: [media] media: pci: remove duplicate checks for EPERM

This patch removes check for EPERM in dbg_g/s_register and
vidioc_g/s_register as this check is already performed by core.

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] media: usb: remove duplicate checks for EPERM in vidioc_g/s_register

This patch removes check for EPERM in vidioc_g/s_register
as this check is already performed by core.

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] media: dvb-frontends: remove duplicate checks for EPERM in dbg_g/s_register

This patch removes check for EPERM in dbg_g/s_register
as this check is already performed by core.

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] media: i2c: remove duplicate checks for EPERM in dbg_g/s_register

This patch removes check for EPERM in dbg_g/s_register of subdevice
drivers as this check is already performed by core.

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] coda: do not use v4l2_dev in coda_timeout

The timeout delayed work might be scheduled even after the v4l2 device is
released.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] coda: fix error return value if v4l2_m2m_ctx_init fails

Use ret from the outer scope, instead of redefining it in the
conditional clause. That way the error value reaches the end of
the function as intended.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] coda: set umask 0644 on debug module param

Otherwise module/coda/parameters/coda_debug won't show up in sysfs.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] coda: enable dmabuf support

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] coda: use devm_ioremap_resource

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] coda: v4l2-compliance fix: add bus_info prefix 'platform'

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] rc: gpio-ir-recv: Remove redundant platform_set_drvdata()

Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] timblogiw: Remove redundant platform_set_drvdata()

Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] bw-qcam: fix timestamp handling

bw-qcam didn't set the timestamp and it didn't set q->timestamp_type.

Tested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] media: i2c: tvp7002: rearrange description of structure members

This patch rearranges the description of field members of
struct tvp7002_config. Also as the all the fields where accepting
a value either 0/1, made the members as bool.

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] media: i2c: tvp7002: remove duplicate define

this patch removes duplicate #define TVP7002_MODULE_NAME
form the driver file, which was also defined in media/tvp7002.h

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] hdpvr: Removed unnecessary use of kzalloc() in get_video_info()

[mchehab@redhat.com: CodingStyle fixes]
Signed-off-by: Leonid Kegulskiy <leo@lumanate.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] videodev2.h: fix typos

This patch fixes several typos in videodev2.h file

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] sony-btf-mpx: Drop needless newline in param description

Module parameter descriptions need not be terminated with a newline.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] sta2x11_vip: fix error return code in sta2x11_vip_init_one()

The orig code will release all the resources if v4l2_device_register()
failed and return 0. But what we need in this case is to return an
negative error code to let the caller known we are failed.
So the patch save the return value of v4l2_device_register() to 'ret'
and return it when error.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] blackfin: fix error return code in bcap_probe()

Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] ad9389b: fix error return code in ad9389b_probe()

Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] vpif_capture: fix error return code in vpif_probe()

Fix to return -ENODEV in the subdevice register error handling
case instead of 0, as done elsewhere in this function.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] vpif_display: fix error return code in vpif_probe()

Fix to return -ENODEV in the subdevice register error handling
case instead of 0, as done elsewhere in this function.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] v4l: vb2: fix error return code in __vb2_init_fileio()

Fix to return -EINVAL in the get kernel address error handling
case instead of 0, as done elsewhere in this function.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] media: fix hdpvr kconfig/build errors

Fix hdpvr build errors when CONFIG_I2C=m and VIDEO_V4L2=m and
VIDEO_HDPVR=y.
drivers/built-in.o: In function `hdpvr_disconnect':
hdpvr-core.c:(.text+0xef542): undefined reference to `v4l2_device_disconnect'
hdpvr-core.c:(.text+0xef57e): undefined reference to `i2c_del_adapter'
hdpvr-core.c:(.text+0xef58a): undefined reference to `video_unregister_device'
drivers/built-in.o: In function `hdpvr_delete':
(.text+0xef5b9): undefined reference to `video_device_release'
drivers/built-in.o: In function `hdpvr_probe':
hdpvr-core.c:(.text+0xef63a): undefined reference to `v4l2_device_register'
hdpvr-core.c:(.text+0xefd97): undefined reference to `i2c_del_adapter'
drivers/built-in.o: In function `hdpvr_s_ctrl':
hdpvr-video.c:(.text+0xf03c0): undefined reference to `v4l2_ctrl_activate'
drivers/built-in.o: In function `hdpvr_device_release':
hdpvr-video.c:(.text+0xf0470): undefined reference to `v4l2_device_unregister'
hdpvr-video.c:(.text+0xf0479): undefined reference to `v4l2_ctrl_handler_free'
hdpvr-video.c:(.text+0xf048f): undefined reference to `i2c_del_adapter'
drivers/built-in.o: In function `hdpvr_open':
hdpvr-video.c:(.text+0xf0570): undefined reference to `video_devdata'
hdpvr-video.c:(.text+0xf057b): undefined reference to `v4l2_fh_init'
hdpvr-video.c:(.text+0xf0583): undefined reference to `v4l2_fh_add'
drivers/built-in.o: In function `video_drvdata':
hdpvr-video.c:(.text+0xf08a0): undefined reference to `video_devdata'
drivers/built-in.o: In function `vidioc_s_dv_timings':
hdpvr-video.c:(.text+0xf0d34): undefined reference to `v4l_match_dv_timings'
drivers/built-in.o: In function `hdpvr_poll':
hdpvr-video.c:(.text+0xf1455): undefined reference to `v4l2_ctrl_poll'
drivers/built-in.o: In function `hdpvr_release':
hdpvr-video.c:(.text+0xf18f6): undefined reference to `v4l2_fh_release'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1be3): undefined reference to `v4l2_ctrl_handler_init_class'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1c19): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1c42): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1c6b): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1cac): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1cd5): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o:(.text+0xf1cfe): more undefined references to `v4l2_ctrl_new_std' follow
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1d75): undefined reference to `v4l2_ctrl_new_std_menu'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1d9e): undefined reference to `v4l2_ctrl_new_std_menu'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1dc3): undefined reference to `v4l2_ctrl_new_std_menu'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1de5): undefined reference to `v4l2_ctrl_new_std_menu'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1e18): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1e4b): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1e90): undefined reference to `v4l2_ctrl_cluster'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1e98): undefined reference to `v4l2_ctrl_handler_setup'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1ec1): undefined reference to `video_device_alloc'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1f85): undefined reference to `__video_register_device'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1fac): undefined reference to `v4l2_ctrl_handler_free'
drivers/built-in.o: In function `hdpvr_register_ir_tx_i2c':
(.text+0xf238f): undefined reference to `i2c_new_device'
drivers/built-in.o: In function `hdpvr_register_ir_rx_i2c':
(.text+0xf2434): undefined reference to `i2c_new_device'
drivers/built-in.o: In function `hdpvr_register_i2c_adapter':
(.text+0xf2514): undefined reference to `i2c_add_adapter'
drivers/built-in.o:(.rodata+0x1b368): undefined reference to `video_ioctl2'
drivers/built-in.o:(.rodata+0x1b690): undefined reference to `v4l2_ctrl_log_status'
drivers/built-in.o:(.rodata+0x1b6f8): undefined reference to `v4l2_ctrl_subscribe_event'
drivers/built-in.o:(.rodata+0x1b700): undefined reference to `v4l2_event_unsubscribe'

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] Missing break statement added in smsdvb-main.c

Fix missing break that so that n_layers are not accidentally incorrect
Kernel version: v3.10-rc1

Signed-off-by: Jakob Normark <jakobnormark@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] saa7115: Don't use a dynamic array

At least on s390, gcc complains about that:
    drivers/media/i2c/saa7115.c: In function 'saa711x_detect_chip.constprop.2':
    drivers/media/i2c/saa7115.c:1647:1: warning: 'saa711x_detect_chip.constprop.2' uses dynamic stack allocation [enabled by default]

While for me the above report seems utterly bogus, as the
compiler should be optimizing saa711x_detect_chip, merging
it with saa711x_detect_chip and changing:
char chip_ver[size - 1];
to
char chip_ver[16];

because this function is only called on this code snippet:
char name[17];
...
ident = saa711x_detect_chip(client, id, name, sizeof(name));

It seems that gcc is not optimizing it, at least on s390.

As getting rid of it is easy, let's do it.

Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] videobuf-dma-contig: use vm_iomap_memory()

vm_iomap_memory() provides a better end user interface than
remap_pfn_range(), as it does the needed tests before doing
mmap.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] smscoreapi: Make Siano firmware load more verbose

If firmware load fails, report it as an error.

Signed-off-by: Roberto Alcantara <roberto@eletronica.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] videobuf_vm_{open,close} race fixes

just use videobuf_queue_lock(map->q) to protect map->count; vm_area_operations
->open() and ->close() are called just under vma->vm_mm->mmap_sem, which
doesn't help the drivers at all, since clonal VMAs are normally in different
address spaces...

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] saa7115: Add register setup and config for gm7113c

The gm7113c chip is similar to the original saa7113 chip, so I try to
re-use most of the saa7113 specific setup-/configuration registers.
According to the datasheet, the gm7113c chip has not implemented
any register-addresses after 0x1f, so I add a new entry to for the chip
to the saa711x_has_reg function.
The devices I've seen using this chip will fail to get stable video-sync
if these registers are not zeroed:
R_14_ANAL_ADC_COMPAT_CNTL
R_15_VGATE_START_FID_CHG
R_16_VGATE_STOP
R_17_MISC_VGATE_CONF_AND_MSB
The saa711x_set_v4lstd is updated to send a simpler configuration-table
to avoid setting these registers.

Signed-off-by: Jon Arne Jørgensen <jonarne@jonarne.no>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] saa7115: add detection code for gm7113c

Adds a code that (auto)detects gm7113c clones. The auto-detection
here is not perfect, as, on contrary to what it would be expected
by looking into its datasheets some devices would return, instead:
saa7115 0-0025: chip 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 @ 0x4a is unknown
(found on a device labeled as GM7113C 1145 by Ezequiel Garcia)

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Jon Arne Jørgensen <jonarne@jonarne.no>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] saa7115: move the autodetection code out of the probe function

As we're now seeing other variants from chinese clones, like
gm1113c, we'll need to add more bits at the detection code.
So, move it into a separate function.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Jon Arne Jørgensen <jonarne@jonarne.no>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] wl128x: do not call copy_to_user() while holding spinlocks

copy_to_user() must not be called with spinlocks held, but it is in
fmc_transfer_rds_from_internal_buff().
The patch copies data to tmpbuf, releases spinlock and then passes it to userspace.
By the way there is a small unification: replace a couple of hardcoded constants by a macro.
Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] solo6x10: Approximate frame intervals with non-standard denominator

Instead of falling back to 1/25 (PAL) or 1/30 (NTSC).

Signed-off-by: Ismael Luceno <ismael.luceno@corp.bluecherry.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] media: i2c: tvp7002: enable TVP7002 decoder for media controller based usage

This patch enables tvp7002 decoder driver for media controller
based usage by adding v4l2_subdev_pad_ops  operations support
for enum_mbus_code, set_pad_format, get_pad_format and media_entity_init()
on probe and media_entity_cleanup() on remove.

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] hdpvr: Added some error handling in hdpvr_start_streaming()

Signed-off-by: Leonid Kegulskiy <leo@lumanate.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] hdpvr: Removed unnecessary get_video_info() call from hdpvr_device_init()

Signed-off-by: Leonid Kegulskiy <leo@lumanate.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] media: davinci: vpbe: fix checkpatch warning for CamelCase

This patch fixes checkpatch warning to avoid CamelCase.

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

upstream: [media] em28xx: Add support for 1b80:e1cc Delock 61959

Hardware is the same as MaxMedia UB425-TC but ships with a different
remote.

Signed-off-by: Jakob Haufe <sur5r@sur5r.net>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>