platform/kernel/u-boot.git
4 years agotools: k3_gen_x509_cert: Set default early HS JTAG access to disabled
Andrew F. Davis [Wed, 27 May 2020 13:47:55 +0000 (09:47 -0400)]
tools: k3_gen_x509_cert: Set default early HS JTAG access to disabled

When authenticating the initial boot binary the ROM will check a debug
type value in the certificate and based on that open JTAG access to that
core. This only effects HS devices as non-HS device ROM allows JTAG
by default.

This can be useful for HS developers working in the early boot stage,
before SYSFW is loaded. After that point the JTAG access can be
changed based on board configurations passed to SYSFW.

This access can also be a large security problem as JTAG access on
HS devices can be used to circumvent the chain-of-trust controls.
Accidentally leaving this open defeats the security on HS, due to this
change the default to disabled.

This should only effect those working on early HS boot code, which
is a limited crowd who will already know how to re-enable this access
as needed.

Signed-off-by: Andrew F. Davis <afd@ti.com>
4 years agotools: k3_gen_x509_cert: Allow selecting early JTAG debug value
Andrew F. Davis [Wed, 27 May 2020 13:47:54 +0000 (09:47 -0400)]
tools: k3_gen_x509_cert: Allow selecting early JTAG debug value

When authenticating the initial boot binary the ROM will check a debug
type value in the certificate and based on that open JTAG access to that
core.

Make this selectable in the signing tool to allow it to be enabled or
disabled based on user command line input.

This does not change the default behavior.

Signed-off-by: Andrew F. Davis <afd@ti.com>
4 years agommc: davinci_mmc: Cleanup to use dt in U-boot and static platdata in SPL
Faiz Abbas [Fri, 22 May 2020 02:02:28 +0000 (07:32 +0530)]
mmc: davinci_mmc: Cleanup to use dt in U-boot and static platdata in SPL

Cleanup this driver to use dt in U-boot and static platdata in SPL.
This requires the following steps:

1. Move all platdata assignment from probe() to ofdata_to_platdata().
   This function is only called in U-boot.
2. Replicate all the platdata assignment being done in
   ofdata_to_platdata() in the omapl138 board file. This data is used in
   the SPL case where SPL_OF_CONTROL is not enabled.
3. Remove SPL_OF_CONTROL and related configs from omapl138_lcdk_defconfig

This cleanup effectively reverts 3ef94715cc ('mmc: davinci: fix mmc boot in SPL')

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
4 years agoboard: ti: use positive logic to detect idk boards
Luca Ceresoli [Thu, 21 May 2020 13:06:25 +0000 (15:06 +0200)]
board: ti: use positive logic to detect idk boards

am57x_idk_lcd_detect() exits immediately if a known board not having
an LCD is found, i.e. a non-IDK board. This is annoying as we have to
remember to add an extra OR clause for every new non-IDK board.

Add a board_is_ti_idk() macro so that the logic becomes positive (detect
LCD on IDK boards instead of not-known-without-LCD boards). Even more
important, add the macro just below the board_is_*_idk() macros, so it is
easy to remember to update it when adding a new IDK.

Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
4 years agoboard: ti: am57xx: use GPIO_TO_PIN() to define GPIO number
Luca Ceresoli [Thu, 21 May 2020 13:06:24 +0000 (15:06 +0200)]
board: ti: am57xx: use GPIO_TO_PIN() to define GPIO number

Using the macro makes code readable without the need for a comment.

Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
4 years agoMerge tag 'u-boot-imx-20200609' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
Tom Rini [Tue, 9 Jun 2020 13:17:24 +0000 (09:17 -0400)]
Merge tag 'u-boot-imx-20200609' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx

Fixes for 2020.07
-----------------

- mx53: mx53menlo Convert to DM_ETH, fix fail boot
- imx8mp_evk: fix boot issue
- MX6, display5: fix environment
- drop warnings (watchdog) for i.MX8mm i.mx8mp
- enable bootaux for i.MX8M

Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/695929999

4 years agoRevert "imx: rom api: fix image offset computation"
Stefano Babic [Tue, 9 Jun 2020 09:19:55 +0000 (11:19 +0200)]
Revert "imx: rom api: fix image offset computation"

This reverts commit 1f63ee656698724bcdc4e711b4ccd267f6bf64ab.

As reported by Ye Li on ML:

1. Removing the image_offset will break secondary (redundant) boot support for sd and emmc.
2. When booting from emmc boot partition, the image_offset is 0. But the flash.bin
generated by mkimage with imximage-8mp-lpddr4.cfg is for sd. It expects to be burn at 32KB offset.
The fit offset 0x60000 has already included the 32KB offset.  So when you burn this flash.bin
to emmc boot partition at offset 0, the fit offset should subtract the 32KB (0x60000 - 0x8000).

Signed-off-by: Stefano Babic <sbabic@denx.de>
4 years agoPrepare v2020.07-rc4
Tom Rini [Tue, 9 Jun 2020 00:30:26 +0000 (20:30 -0400)]
Prepare v2020.07-rc4

Signed-off-by: Tom Rini <trini@konsulko.com>
4 years agocmd: Correct the 'md.q' command
Simon Glass [Mon, 8 Jun 2020 02:33:00 +0000 (20:33 -0600)]
cmd: Correct the 'md.q' command

This displays incorrect data at present due to a missing header file
in display_options. Fix it.

Fixes: 09140113108 ("command: Remove the cmd_tbl_t typedef")

Signed-off-by: Simon Glass <sjg@chromium.org>
4 years agoMerge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xx
Tom Rini [Mon, 8 Jun 2020 12:51:59 +0000 (08:51 -0400)]
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xx

- DM_ETH support for P2041RDB, T1024RDB, P5040DS, P3041DS, P4080DS, bug
  fixes
- Add TBI PHY access through MII
- DDR: Rework errata workaround for A008109, A008378, 009942

4 years agoMerge tag 'u-boot-rockchip-20200607' of https://gitlab.denx.de/u-boot/custodians...
Tom Rini [Mon, 8 Jun 2020 12:51:30 +0000 (08:51 -0400)]
Merge tag 'u-boot-rockchip-20200607' of https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip

- revive rk3399 puma board to adapt mainline dts;
- Fix rk3399-evb stdout path;
- Enable PCIe for rk3399: Rockpro64, firefly, pinebookpro;
- Add rk3328 Rock-pi-e board;
- Enable SPI boot for rockpro64 and roc-pc-rk3399;

4 years agoARM: dts: imx: m53menlo: Convert to DM_ETH
Marek Vasut [Sat, 30 May 2020 20:44:46 +0000 (22:44 +0200)]
ARM: dts: imx: m53menlo: Convert to DM_ETH

Convert the board to DM_ETH instead of legacy networking. This requires
a minor addition to the DT to satisfy the requirement for specifying a
PHY node. No functional change from board user perspective.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
4 years agoARM: imx: m53menlo: Do not fail boot on invalid splash screen
Marek Vasut [Sat, 30 May 2020 20:44:45 +0000 (22:44 +0200)]
ARM: imx: m53menlo: Do not fail boot on invalid splash screen

None of these splash screen loading errors are so critical as to
justify complete failure to boot, so just print error message as
needed and return 0, the boot can very likely continue without
the splash.

Fix a couple of missing free(dst) instances as well.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
4 years agoARM: imx: ddr: Add missing PHY reset
Marek Vasut [Sat, 30 May 2020 00:14:48 +0000 (02:14 +0200)]
ARM: imx: ddr: Add missing PHY reset

The iMX7D RM 9.2.4.9.3 Power removal flow Table 9-11. Re-enabling power
explicitly says both the DDR controller and the PHY must be reset in the
correct sequence. Currently the code only resets the controller. This
leads to a misbehavior where the system brings the DRAM up after reboot,
but the DRAM is unstable. Add the missing reset.

The easiest way to trigger this is by triggering WDT without having the
WDT assert WDOG_B signal, i.e. mw.w 0x30280000 0x25 .

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
4 years agopower: pmic: Add SPL Kconfig entry for PFUZE100
Marek Vasut [Fri, 29 May 2020 17:22:41 +0000 (19:22 +0200)]
power: pmic: Add SPL Kconfig entry for PFUZE100

Add Kconfig entry for the PFUZE PMIC, SPL variant.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
4 years agoimx: imx8mp_evk: fix boot issue
Peng Fan [Tue, 26 May 2020 23:33:50 +0000 (20:33 -0300)]
imx: imx8mp_evk: fix boot issue

The u-boot-spl.bin pad with ddr firmware conflicts with the
CONFIG_MALLOC_F_ADDR area, the ddr firmware will be overwritten
by malloc in SPL stage and cause ddr initialization not able
to finish. So update the related addresses to fix the issue.

Reported-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
4 years agoimx8mp_evk: spl: no need the code since spl framework could do that
Peng Fan [Tue, 26 May 2020 23:33:49 +0000 (20:33 -0300)]
imx8mp_evk: spl: no need the code since spl framework could do that

We no need invoke the code, since spl framework could help
us do that.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
4 years agoimx8mp_evk: spl: use spl_early_init
Peng Fan [Tue, 26 May 2020 23:33:48 +0000 (20:33 -0300)]
imx8mp_evk: spl: use spl_early_init

Use spl_early_init to replace spl_init, spl_init will be invoked
in board_init_r, we only need use spl_early_init to setup malloc
and scan early dt.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
4 years agoimx8mp_evk: spl: drop timer_init
Peng Fan [Tue, 26 May 2020 23:33:47 +0000 (20:33 -0300)]
imx8mp_evk: spl: drop timer_init

timer_init has been invoked in arch_cpu_init, no need to invoke
it again in board code.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
4 years agoimx8mp_evk: spl: drop useless code
Peng Fan [Tue, 26 May 2020 23:33:46 +0000 (20:33 -0300)]
imx8mp_evk: spl: drop useless code

Drop useless getting ccm device, there is no need to explicted do this
in board code, and we not enable SPL CLK currently.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
4 years agoimx: Update MTD partitions layout for display5 (i.MX6Q) board
Lukasz Majewski [Wed, 13 May 2020 15:45:15 +0000 (17:45 +0200)]
imx: Update MTD partitions layout for display5 (i.MX6Q) board

This change updates the MTD partition layout on SPI-NOR memory for display5
board.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
4 years agoimx: rom api: fix image offset computation
Sébastien Szymanski [Wed, 13 May 2020 14:02:28 +0000 (16:02 +0200)]
imx: rom api: fix image offset computation

When not booting from FlexSPI, the offset computation is:

offset = image_offset + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512 - 0x8000;

When booting from SD card or eMMC user partition, image_offset is
0x8000. It is useless to add and remove 0x8000.
When booting from other device, image_offset is 0 so this computation is wrong.

Simplfy this computation to work on all booting devices.

Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
4 years agoverdin-imx8mm: Select the watchdog driver
Fabio Estevam [Mon, 11 May 2020 14:00:31 +0000 (11:00 -0300)]
verdin-imx8mm: Select the watchdog driver

Currently watchdog driver is not selected, which causes system to reboot
after staying 60s in the U-Boot prompt.

Fix this problem by enabling CONFIG_WATCHDOG so that watchdog can be
properly serviced.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
4 years agoimx8mp_evk: Select the watchdog driver
Fabio Estevam [Mon, 11 May 2020 14:00:30 +0000 (11:00 -0300)]
imx8mp_evk: Select the watchdog driver

Currently watchdog driver is not selected, which causes system to reboot
after staying 60s in the U-Boot prompt.

Fix this problem by enabling CONFIG_WATCHDOG so that watchdog can be
properly serviced.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
4 years agoimx8mm_beacon: Select the watchdog driver
Fabio Estevam [Mon, 11 May 2020 14:00:29 +0000 (11:00 -0300)]
imx8mm_beacon: Select the watchdog driver

Currently watchdog driver is not selected, which causes system to reboot
after staying 60s in the U-Boot prompt.

Fix this problem by enabling CONFIG_WATCHDOG so that watchdog can be
properly serviced.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Adam Ford <aford173@gmail.com>
4 years agoimx8mn_ddr4_evk: Select the watchdog driver
Fabio Estevam [Mon, 11 May 2020 14:00:28 +0000 (11:00 -0300)]
imx8mn_ddr4_evk: Select the watchdog driver

Currently watchdog driver is not selected, which causes system to reboot
after staying 60s in the U-Boot prompt.

Fix this problem by enabling CONFIG_WATCHDOG so that watchdog can be
properly serviced.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
4 years agoimx8mm_evk: Select the watchdog driver
Fabio Estevam [Mon, 11 May 2020 14:00:27 +0000 (11:00 -0300)]
imx8mm_evk: Select the watchdog driver

Currently the watchdog driver is not selected, which causes the following
warnings in both SPL and U-Boot proper:

U-Boot SPL 2020.07-rc1-00387-g67887903af (May 07 2020 - 23:49:27 -0300)
Normal Boot
WDT:   Started without servicing (60s timeout)
Trying to boot from MMC1

U-Boot 2020.07-rc1-00387-g67887903af (May 07 2020 - 23:49:27 -0300)

CPU:   Freescale i.MX8MMQ rev1.0 at 1200 MHz
Reset cause: POR
Model: FSL i.MX8MM EVK board
DRAM:  2 GiB
WDT:   Started without servicing (60s timeout)
....

System reboots after staying 60s in the U-Boot prompt.

Fix this problem by enabling CONFIG_WATCHDOG so that watchdog can be
properly serviced.

Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
4 years agoimx8mp_evk: Add a README file
Fabio Estevam [Mon, 11 May 2020 12:45:51 +0000 (09:45 -0300)]
imx8mp_evk: Add a README file

Add a README file explaining the U-Boot build and SD card flash procedures.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
4 years agoimx: move ATF to the back of the FIT to fix loading over yModem
Patrick Wildt [Fri, 8 May 2020 09:59:47 +0000 (11:59 +0200)]
imx: move ATF to the back of the FIT to fix loading over yModem

With yModem the FIT Image is only supplied once, so we can only
seek forward in the yModem supplied image and never backwards.
With the recent changes to the SPL mechanism, including loading
U-Boot first, FDT after, then the loadables, we must also reorder
the FIT image script to make sure that the loadables are last in
the FIT image.

Signed-off-by: Patrick Wildt <patrick@blueri.se>
Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
4 years agoimx: Kconfig: enable IMX_BOOTAUX for i.MX8M
Peng Fan [Tue, 5 May 2020 12:18:02 +0000 (20:18 +0800)]
imx: Kconfig: enable IMX_BOOTAUX for i.MX8M

i.MX8M could use imx bootaux to boot m4/m7 core, so let's add it
to the dependency list.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
4 years agoARM: dts: imxrt1050: indent lcdif node correctly
Giulio Benetti [Tue, 28 Apr 2020 16:20:11 +0000 (18:20 +0200)]
ARM: dts: imxrt1050: indent lcdif node correctly

Accidentally submitted a patch with indentation not correct, let's fix it
by indenting wrong lines.

Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
4 years agorockchip: enable PCIe and NVMe on Pinebook Pro
Patrick Wildt [Sun, 7 Jun 2020 10:08:35 +0000 (12:08 +0200)]
rockchip: enable PCIe and NVMe on Pinebook Pro

Enable CONFIG_PCI and CONFIG_NVME and related configs for the
Pinebook Pro.

Signed-off-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
4 years agorockchip: puma: enable new usb config options
Heiko Stuebner [Fri, 5 Jun 2020 10:06:43 +0000 (12:06 +0200)]
rockchip: puma: enable new usb config options

With recently added changes we get support for usb3 including handling
of the phys (type-c and inno-usb2), so enable the necessary config
options on puma.

Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
4 years agorockchip: puma: drop special handling of usb host regulator
Heiko Stuebner [Fri, 5 Jun 2020 10:06:42 +0000 (12:06 +0200)]
rockchip: puma: drop special handling of usb host regulator

With the current usb stack in u-boot, all host ports on puma work
flawlessly without any additional special handling, so drop that
usb hub hacking from the puma board.

Tested with mass-storage and usb-ethernet on both usb3 and usb2 ports.

Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
4 years agorockchip: puma: remove separate fit generator
Heiko Stuebner [Fri, 5 Jun 2020 10:06:41 +0000 (12:06 +0200)]
rockchip: puma: remove separate fit generator

The introduction of the puma-specific generator was mainly a way
to split the pmu firmware from the ATF binary and not having to
distribute that 4GB (sparse) image that was created before moving
to the bl31.elf as base.

Looking at the publically available repository for that separate
pmu firmware
    https://git.theobroma-systems.com/rk3399-cortex-m0.git/
there is also no activity for 3 years and apart from some build
customizations no other changes were done.

And even then, if changes need to be made, this can very well also
happen in the atf context itself, so there is no real need to
diverge from the established build procedure and we can just go
back to using the main make_fit_atf.py script.

Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
4 years agorockchip: puma: reorganize devicetrees to actually work and match upstream
Heiko Stuebner [Fri, 5 Jun 2020 10:06:40 +0000 (12:06 +0200)]
rockchip: puma: reorganize devicetrees to actually work and match upstream

So far the puma dts files only just included the main puma dtsi without
handling the actual baseboard and rk3399-puma.dtsi was very much
detached from the variant in the mainline Linux kernel.

Recent changes resulted in a strange situation with nonworking puma boards.

Commit ab800e5a6f28 ("arm: dts: rockchip: puma: move U-Boot specific bits to u-boot.dtsi")
moved the sdram include from rk3399-puma-ddrX.dts to new files
rk3399-puma-ddrx-u-boot.dtsi which were never included anywhere though.

Commit 167efc2c7a46 ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux")
replaced the rk3399-puma.dtsi nearly completely, but in the kernel
it definitly depends on a baseboard dts to actually enable peripherals
like sd-slot, uarts, etc.

So to untagle this and bring the whole thing more in line with mainline
Linux, bring the rk3399-puma-haikou.dts over as well, drop the separate
DDR-option devicetrees and instead replace them with a puma Kconfig option
to select and include the needed DDR variant.

Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
4 years agorockchip: puma: fix indentation of misc_init_r
Heiko Stuebner [Fri, 5 Jun 2020 10:06:39 +0000 (12:06 +0200)]
rockchip: puma: fix indentation of misc_init_r

The commit moving puma to the generic cpuid/macaddr helpers used 7 spaces
as indentation, so correct that by moving to the required tabs.

Fixes: fa177ff0208b ("board: puma: Use rockchip_* helpers to setup cpuid and macaddr")
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
4 years agorockchip: puma: fix indentation for -u-boot.dtsi
Heiko Stuebner [Fri, 5 Jun 2020 10:06:38 +0000 (12:06 +0200)]
rockchip: puma: fix indentation for -u-boot.dtsi

Tabs not spaces, so transform it to the common styling.

Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
4 years agoarm64: dts: rk3399-puma: fix gpio levels for vcc5v0-host regulator
Heiko Stuebner [Fri, 5 Jun 2020 10:06:37 +0000 (12:06 +0200)]
arm64: dts: rk3399-puma: fix gpio levels for vcc5v0-host regulator

The regulator enable-gpio uses opposite values for the declaration
vs. the enable_active_low property, breaking the regulator enablement.

Make the usbhost-supply work again by bringing them in sync again.

This mimics the upstream Linux change found on:
http://lore.kernel.org/r/20200604091239.424318-1-heiko@sntech.de

Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
4 years agoarm64: dts: rk3399-puma: fix gpio levels for gmac reset pin
Heiko Stuebner [Fri, 5 Jun 2020 10:06:36 +0000 (12:06 +0200)]
arm64: dts: rk3399-puma: fix gpio levels for gmac reset pin

The gmac reset has opposite values for the gpio declaration
and the separate reset-active, bring this in line to make
u-boot also find the ethernet-phy.

This mimics the upstream Linux commit found on
https://lore.kernel.org/r/20200603132836.362519-1-heiko@sntech.de

Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
4 years agorockchip: rockpro64: add SPI boot
Marcin Juszkiewicz [Wed, 3 Jun 2020 15:15:13 +0000 (17:15 +0200)]
rockchip: rockpro64: add SPI boot

U-Boot TPL 2020.07-rc3-00121-gab88251130 (Jun 03 2020 - 16:43:42)
Channel 0: LPDDR4, 50MHz
BW=32 Col=10 Bk=8 CS0 Row=16/15 CS=1 Die BW=16 Size=2048MB
Channel 1: LPDDR4, 50MHz
BW=32 Col=10 Bk=8 CS0 Row=16/15 CS=1 Die BW=16 Size=2048MB
256B stride
256B stride
lpddr4_set_rate: change freq to 400000000 mhz 0, 1
lpddr4_set_rate: change freq to 800000000 mhz 1, 0
Trying to boot from BOOTROM
Returning to boot ROM...

U-Boot SPL 2020.07-rc3-00121-gab88251130 (Jun 03 2020 - 16:43:42 +0200)
Trying to boot from SPI

U-Boot 2020.07-rc3-00121-gab88251130 (Jun 03 2020 - 16:43:42 +0200)

SoC: Rockchip rk3399
Reset cause: RST
Model: Pine64 RockPro64 v2.1
DRAM:  3.9 GiB
PMIC:  RK808
MMC:   mmc@fe310000: 2, mmc@fe320000: 1, sdhci@fe330000: 0
Loading Environment from SPI Flash... SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   vidconsole
Err:   vidconsole
Model: Pine64 RockPro64 v2.1
Net:   eth0: ethernet@fe300000
Hit any key to stop autoboot:  0
=>

Signed-off-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
4 years agorockchip: rockpro64: Store default env into SPI
Marcin Juszkiewicz [Wed, 3 Jun 2020 15:15:12 +0000 (17:15 +0200)]
rockchip: rockpro64: Store default env into SPI

Board has flash chip on board so let store U-Boot environment there.

Signed-off-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
4 years agodoc: rockchip: Document SPI flash program steps
Jagan Teki [Thu, 4 Jun 2020 14:51:41 +0000 (20:21 +0530)]
doc: rockchip: Document SPI flash program steps

Document SPI flash program steps for rockchip platforms.

Suggested-by: Hugh Cole-Baker <sigmaris@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
4 years agoroc-rk3399-pc: Add SPI boot
Jagan Teki [Thu, 4 Jun 2020 14:51:40 +0000 (20:21 +0530)]
roc-rk3399-pc: Add SPI boot

U-Boot TPL 2020.07-rc3-00090-gd4e919f927-dirty (Jun 01 2020 - 23:45:53)
Channel 0: LPDDR4, 50MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB
Channel 1: LPDDR4, 50MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB
256B stride
256B stride
lpddr4_set_rate: change freq to 400000000 mhz 0, 1
lpddr4_set_rate: change freq to 800000000 mhz 1, 0
Trying to boot from BOOTROM
Returning to boot ROM...

U-Boot SPL 2020.07-rc3-00087-ga21e9fd385 (Jun 02 2020 - 00:09:45 +0530)
Trying to boot from MMC1
NOTICE:  BL31: v2.2(release):
NOTICE:  BL31: Built : 15:05:37, May 12 2020

U-Boot 2020.07-rc3-00087-ga21e9fd385 (Jun 02 2020 - 00:09:45 +0530)

SoC: Rockchip rk3399
Reset cause: POR
Model: Firefly ROC-RK3399-PC Board
DRAM:  3.9 GiB
PMIC:  RK808
MMC:   mmc@fe320000: 1, sdhci@fe330000: 0
Loading Environment from SPI Flash... SF: Detected w25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Model: Firefly ROC-RK3399-PC Board

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
4 years agoroc-rk3399-pc: Mark default env from SPI
Jagan Teki [Thu, 4 Jun 2020 14:51:39 +0000 (20:21 +0530)]
roc-rk3399-pc: Mark default env from SPI

Mark the default U-Boot environment as SPI flash since
this is an on board flash device.

Updated env offset, size in contrast with default since
the U-Boot proper has to start from 384K.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
4 years agoMakefile: Drop to handle rkspi image type
Jagan Teki [Thu, 4 Jun 2020 14:51:38 +0000 (20:21 +0530)]
Makefile: Drop to handle rkspi image type

On rockchip platforms, SPI boot image creation is not
straightforward like MMC boot image creation where former
requires to specify tpl, spl in multimage format in mkimage,
and later simply do a concatenate mkimaged-tpl with spl.

On this note, let drop rkspi image type creation via kbuild
and let inform via rockchip.rst

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
4 years agorockchip: rk3399-evb: add stdout-path for the board
Kever Yang [Wed, 3 Jun 2020 07:25:28 +0000 (15:25 +0800)]
rockchip: rk3399-evb: add stdout-path for the board

The 'stdout-path' is missing after dts sync.
Fixes: 167efc2c7a ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux")

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
4 years agorockchip: rk3328: add rock-pi-e-rk3328_defconfig file
b.l.huang [Sun, 31 May 2020 16:02:11 +0000 (00:02 +0800)]
rockchip: rk3328: add rock-pi-e-rk3328_defconfig file

This commit add the default configuration file and relevant description
for rock-pi-e board

Signed-off-by: Banglang Huang <banglang.huang@foxmail.com>
4 years agorockchip: rk3328: add rock-pi-e dts file
b.l.huang [Sun, 31 May 2020 16:01:28 +0000 (00:01 +0800)]
rockchip: rk3328: add rock-pi-e dts file

The ROCK-PI-E is a credit card size SBC based on Rockchip RK3328
Quad-Core ARM Cortex A53.

    Net - Dual ethernet port, 1 X Gbe, 1 X 100M
    USB - USB 3.0
    DC  - USB-Type C, 5V 2A
    Storage - TF card, eMMC

Just build idbloader.img and u-boot.itb for Rockpi E board and
follow the blow steps to replace the relevant partition.

    dd if=idbloader.img of=/dev/sdcard seek=64 conv=notrunc
    dd if=u-boot.itb of=/dev/sdcard seek=16384 conv=notrunc

Signed-off-by: Banglang Huang <banglang.huang@foxmail.com>
4 years agorockchip: Enable PCIe and NVMe on ROCKPro64
Mark Kettenis [Mon, 25 May 2020 09:00:57 +0000 (11:00 +0200)]
rockchip: Enable PCIe and NVMe on ROCKPro64

Enable CONFIG_PCI and CONFIG_NVME and related configs for the
ROCKPro64 board.

Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
4 years agorockchip: Enable PCIe/M.2 and NVMe on Firefly RK3399
Mark Kettenis [Mon, 25 May 2020 09:00:56 +0000 (11:00 +0200)]
rockchip: Enable PCIe/M.2 and NVMe on Firefly RK3399

Enable CONFIG_PCI and CONFIG_NVME and related configs for the
Firefly RK3399 board.

Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
4 years agoMerge tag 'efi-2020-07-rc4-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Tom Rini [Sat, 6 Jun 2020 14:59:55 +0000 (10:59 -0400)]
Merge tag 'efi-2020-07-rc4-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi

Pull request for UEFI sub-system for efi-2020-07-rc4 (2)

The following problems are resolved:

* When booting via UEFI an SMBIOS table is presented to the operating
  system. If U-Boot tries to add an empty string, this results in corrupted
  SMBIOS information. We will now use "Unknown" as property value.
* The EFI_RNG_PROTOCOL uses the DM_RNG drivers. For the virtio RNG driver
  the missing DM_RNG Kconfig dependency is added.
* Missing function descriptions for the EFI_SIMPLE_TEXT_OUTPUT_PROTOCOL are
  added.

4 years agoefi_loader: comments EFI_SIMPLE_TEXT_OUTPUT_PROTOCOL
Heinrich Schuchardt [Thu, 4 Jun 2020 16:40:44 +0000 (18:40 +0200)]
efi_loader: comments EFI_SIMPLE_TEXT_OUTPUT_PROTOCOL

Provide missing comments for the functions implementing the
EFI_SIMPLE_TEXT_OUTPUT_PROTOCOL.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
4 years agovirtio: VIRTIO_RNG depends on DM_RNG
Heinrich Schuchardt [Sun, 31 May 2020 09:02:42 +0000 (11:02 +0200)]
virtio: VIRTIO_RNG depends on DM_RNG

Add the missing Kconfig dependency and let VIRTIO_RNG default to yes.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
4 years agosmbios: empty strings in smbios_add_string()
Heinrich Schuchardt [Mon, 1 Jun 2020 13:44:00 +0000 (15:44 +0200)]
smbios: empty strings in smbios_add_string()

smbios_add_string() cannot deal with empty strings. This leads to incorrect
property values and invalid tables. E.g. for the pine64-lts_defconfig
CONFIG_SMBIOS_MANUFACTURER="". Linux command dmidecode shows:

Table 1:
    Manufacturer: sunxi
    Product Name: sunxi

Table 3:
    Invalid entry length (2). DMI table is broken! Stop.

Replace empty strings by "Unknown".

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
4 years agoconfigs: Resync with savedefconfig
Tom Rini [Thu, 4 Jun 2020 23:29:09 +0000 (19:29 -0400)]
configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
4 years agoMerge branch '2020-06-04-misc-bugfixes'
Tom Rini [Thu, 4 Jun 2020 22:12:57 +0000 (18:12 -0400)]
Merge branch '2020-06-04-misc-bugfixes'

- Resync checkpatch.pl (largely) with v5.7 and introduce U-Boot specific
  checks in a localized area, so they aren't lost in the future.
- Complete / re-migrate some options from config headers to defconfigs
- Add dependencies to the various debug uart drivers

4 years agocheckpatch.pl: Add check for defining CONFIG_CMD_xxx via config files
Tom Rini [Tue, 26 May 2020 18:29:02 +0000 (14:29 -0400)]
checkpatch.pl: Add check for defining CONFIG_CMD_xxx via config files

All of our cmds have a Kconfig entry.  Making enabling a CMD via the
config file an error to checkpatch.pl.

Signed-off-by: Tom Rini <trini@konsulko.com>
4 years agocheckpatch.pl: Request if() instead #ifdef
Simon Glass [Fri, 22 May 2020 22:32:40 +0000 (16:32 -0600)]
checkpatch.pl: Request if() instead #ifdef

There is a lot of use of #ifdefs in U-Boot. In an effort reduce this,
suggest using the compile-time construct.

Signed-off-by: Simon Glass <sjg@chromium.org>
4 years agocheckpatch.pl: Request a test when a new command is added
Simon Glass [Fri, 22 May 2020 22:32:39 +0000 (16:32 -0600)]
checkpatch.pl: Request a test when a new command is added

This request is made with nearly every new command. Point to some docs
on how to do it.

Signed-off-by: Simon Glass <sjg@chromium.org>
4 years agocheckpatch.pl: Warn if the flattree API is used
Simon Glass [Fri, 22 May 2020 22:32:38 +0000 (16:32 -0600)]
checkpatch.pl: Warn if the flattree API is used

We want people to use the livetree API, so request it.

Signed-off-by: Simon Glass <sjg@chromium.org>
4 years agocheckpatch.pl: Add a check for tests needed for uclasses
Simon Glass [Fri, 22 May 2020 22:32:37 +0000 (16:32 -0600)]
checkpatch.pl: Add a check for tests needed for uclasses

A common problem when submitting a new uclass is to forget to add sandbox
tests. Add a warning for this.

Of course tests should always be added for new code, but this one seems to
be missed by nearly every new contributor.

Signed-off-by: Simon Glass <sjg@chromium.org>
4 years agocheckpatch.pl: Add a U-Boot option
Simon Glass [Fri, 22 May 2020 22:32:36 +0000 (16:32 -0600)]
checkpatch.pl: Add a U-Boot option

Add an option to indicate that U-Boot-specific checks should be enabled.
Add a function to house the code that will be added.

Signed-off-by: Simon Glass <sjg@chromium.org>
4 years agocheckpatch.pl: Update to v5.7
Simon Glass [Fri, 22 May 2020 22:32:35 +0000 (16:32 -0600)]
checkpatch.pl: Update to v5.7

Keep the U-Boot changes to $logFunctions

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Resync with v5.7 release which changed the default max line
 length, update commit to reflect]
Signed-off-by: Tom Rini <trini@konsulko.com>
4 years agoConvert CONFIG_BOARD_LATE_INIT to Kconfig
Tom Rini [Tue, 26 May 2020 19:06:19 +0000 (15:06 -0400)]
Convert CONFIG_BOARD_LATE_INIT to Kconfig

This converts the following to Kconfig:
   CONFIG_BOARD_LATE_INIT

Signed-off-by: Tom Rini <trini@konsulko.com>
4 years agoConvert CONFIG_CMD_ASKENV et al to Kconfig
Tom Rini [Tue, 26 May 2020 19:06:18 +0000 (15:06 -0400)]
Convert CONFIG_CMD_ASKENV et al to Kconfig

This converts the following to Kconfig:
   CONFIG_CMD_ASKENV
   CONFIG_CMD_BMP
   CONFIG_CMD_BOOTD
   CONFIG_CMD_CACHE
   CONFIG_CMD_CRC32
   CONFIG_CMD_DHCP
   CONFIG_CMD_ENV
   CONFIG_CMD_EXPORTENV
   CONFIG_CMD_EXT2
   CONFIG_CMD_EXT4
   CONFIG_CMD_FLASH
   CONFIG_CMD_FS_GENERIC
   CONFIG_CMD_FUSE
   CONFIG_CMD_GPIO
   CONFIG_CMD_GPT
   CONFIG_CMD_GREPENV
   CONFIG_CMD_I2C
   CONFIG_CMD_IMLS
   CONFIG_CMD_IMPORTENV
   CONFIG_CMD_LOADB
   CONFIG_CMD_LOADS
   CONFIG_CMD_MEMINFO
   CONFIG_CMD_MII
   CONFIG_CMD_MTDPARTS
   CONFIG_CMD_NAND
   CONFIG_CMD_NAND_TRIMFFS
   CONFIG_CMD_NFS
   CONFIG_CMD_PCA953X
   CONFIG_CMD_PCA953X_INFO
   CONFIG_CMD_PCI
   CONFIG_CMD_PING
   CONFIG_CMD_READ
   CONFIG_CMD_SF
   CONFIG_CMD_SPI
   CONFIG_CMD_SPL
   CONFIG_CMD_SPL_WRITE_SIZE
   CONFIG_CMD_TIME
   CONFIG_CMD_TRACE
   CONFIG_CMD_UBI
   CONFIG_CMD_UBIFS
   CONFIG_CMD_UNZIP
   CONFIG_FS_EXT4

Signed-off-by: Tom Rini <trini@konsulko.com>
4 years agoConvert CONFIG_BZIP2 et al to Kconfig
Tom Rini [Tue, 26 May 2020 19:06:17 +0000 (15:06 -0400)]
Convert CONFIG_BZIP2 et al to Kconfig

This converts the following to Kconfig:
   CONFIG_BZIP2
   CONFIG_GZIP
   CONFIG_LZO
   CONFIG_ZLIB
   CONFIG_LZMA
   CONFIG_LZO

Signed-off-by: Tom Rini <trini@konsulko.com>
4 years agotopic_miami: Disable GPIO
Tom Rini [Tue, 26 May 2020 19:06:16 +0000 (15:06 -0400)]
topic_miami: Disable GPIO

Per the boards config header file, there is no useful GPIO on these
boards.  Remove CONFIG_CMD_GPIO from the defconfigs.

Cc: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Tom Rini <trini@konsulko.com>
4 years agoARM: rmobile: blanche: Disable CONFIG_CMD_SF / CONFIG_CMD_SPI
Tom Rini [Tue, 26 May 2020 19:06:15 +0000 (15:06 -0400)]
ARM: rmobile: blanche: Disable CONFIG_CMD_SF / CONFIG_CMD_SPI

The config header for this platform disables both CMD_SF and CMD_SPI and
the defconfig leaves them enabled.  Disable them from the defconfig and
enable them in the header.

Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masakazu Mochizuki <masakazu.mochizuki.wd@hitachi.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
4 years agobcmstb: Migrate CONFIG_CMD_EXT[24]
Tom Rini [Tue, 26 May 2020 19:06:14 +0000 (15:06 -0400)]
bcmstb: Migrate CONFIG_CMD_EXT[24]

The common config header for bcm7260 and bcm7445 enable
CONFIG_CMD_EXT2/EXT4 but the defconfigs do not.  This results in the
commands being disabled.  Enable them via the defconfig.

Cc: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
4 years agomx6memcal: Finish migration to defconfig options
Tom Rini [Tue, 26 May 2020 19:06:13 +0000 (15:06 -0400)]
mx6memcal: Finish migration to defconfig options

The config header for this platform uses '#undef' in a number of cases.
All of the MMC related ones were already handled correctly in the
defconfig file.  In the case of CONFIG_CMD_FUSE, the command was being
built and enabled via defconfig.  Disable it in the defconfig, cleanup
the header.

Reviewed-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
4 years agopfla02: Rework excluding NAND from SPL
Tom Rini [Tue, 26 May 2020 19:06:12 +0000 (15:06 -0400)]
pfla02: Rework excluding NAND from SPL

Rather than only enable CONFIG_CMD_NAND for non-SPL builds, move the CMD
options to defconfig and rework the guards to not try and call the
function in SPL builds.

Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
4 years agoserial: Add missing Kconfig dependencies for debug consoles
Michal Simek [Thu, 28 May 2020 10:05:12 +0000 (12:05 +0200)]
serial: Add missing Kconfig dependencies for debug consoles

Debug console is the part of serial driver in the same file. It means to be
able to enable debug console you also need to enable driver itself.
That's why add all dependecies and list only debug consoles which are
enabled based on driver selection to avoid compilation error when user
asks for certain debug console but driver is not enable for it.

Error:
aarch64-linux-gnu-ld.bfd: common/built-in.o: in function `putc':
/home/monstr/data/disk/u-boot/common/console.c:513: undefined reference to `printch'
aarch64-linux-gnu-ld.bfd: common/built-in.o: in function `puts':
/home/monstr/data/disk/u-boot/common/console.c:563: undefined reference to `printch'

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Fix ns16550 dependency, add ZYNQ_SERIAL, change S5P]
Signed-off-by: Tom Rini <trini@konsulko.com>
4 years agoserial: Convert ARM_DCC to Kconfig
Tom Rini [Tue, 2 Jun 2020 21:26:33 +0000 (17:26 -0400)]
serial: Convert ARM_DCC to Kconfig

The symbol "CONFIG_ARM_DCC" is used to control building
drivers/serial/arm_dcc.c.  Provide a simple Kconfig entry for this.

Cc: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Tom McLeod <tom.mcleod@opalkelly.com>
Cc: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
4 years agoMerge https://gitlab.denx.de/u-boot/custodians/u-boot-riscv
Tom Rini [Thu, 4 Jun 2020 17:50:39 +0000 (13:50 -0400)]
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-riscv

- Fixes 7e249bc13aaf: ("riscv: Move all SMP related SBI calls to
  SBI_v01") Move sbi_probe_extension() out of CONFIG_SBI_V01.
- SiFive FU540 support SPL.

4 years agoMerge tag 'u-boot-atmel-fixes-2020.07-a' of https://gitlab.denx.de/u-boot/custodians...
Tom Rini [Thu, 4 Jun 2020 14:21:51 +0000 (10:21 -0400)]
Merge tag 'u-boot-atmel-fixes-2020.07-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel

First set of u-boot-atmel fixes for 2020.07 cycle

This set includes just two small commits that fix a build warning and
add a missing serial node.

4 years agoddr: Rework errata A008109, A008378, 009942 workaround
Jaiprakash Singh [Tue, 2 Jun 2020 07:14:02 +0000 (12:44 +0530)]
ddr: Rework errata A008109, A008378, 009942 workaround

Move errata A008109, A008378, 009942 workaround implementation from
compute_fsl_memctl_config_regs() to  fsl_ddr_set_memctl_regs()
and add register write after each workaround implementation.

Signed-off-by: Jaiprakash Singh <Jaiprakash.singh@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
4 years agoddr: fsl: Impl. Erratum A008109
Joakim Tjernlund [Wed, 20 Nov 2019 16:07:34 +0000 (17:07 +0100)]
ddr: fsl: Impl. Erratum A008109

Impl. erratum as descibed in errata doc.
Enable A008109 for T1040 and T1024

Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
4 years agonet: tsec: Access TBI PHY through the corresponding MII
Hou Zhiqiang [Sun, 3 May 2020 14:48:43 +0000 (22:48 +0800)]
net: tsec: Access TBI PHY through the corresponding MII

When an eTSEC is configured to use TBI, configuration of the
TBI is done through the MIIM registers for that eTSEC.
For example, if a TBI interface is required on eTSEC2, then
the MIIM registers starting at offset 0x2_5520 are used to
configure it.

Fixes: 9a1d6af55ecd ("net: tsec: Add driver model ethernet support")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
4 years agonet: tsec: Access eTSEC registers using virtual address
Hou Zhiqiang [Sun, 3 May 2020 14:48:42 +0000 (22:48 +0800)]
net: tsec: Access eTSEC registers using virtual address

The current code accesses eTSEC registers using physical
address directly, it's not correct, though no problem on
current platforms. It won't work on platforms, which does
not support 1:1 virtual-physical address map.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
4 years agodoc: dt-bindings: tsec: Correct the Ethernet port compatible string
Hou Zhiqiang [Sun, 3 May 2020 14:48:41 +0000 (22:48 +0800)]
doc: dt-bindings: tsec: Correct the Ethernet port compatible string

Change the compatible string to "fsl,etsec2" for the Ethernet ports,
which is used in the current driver's match table.

Fixes: 69a00875e3db ("doc: dt-bindings: Describe Freescale TSEC ethernet controller")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
4 years agoconfigs: enable DM_ETH support for T1024RDB
Madalin Bucur [Thu, 30 Apr 2020 13:00:15 +0000 (16:00 +0300)]
configs: enable DM_ETH support for T1024RDB

Enable DM_ETH on all the defconfigs for the T1024RDB board.

Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
4 years agoconfigs: enable DM_ETH support for P2041RDB
Madalin Bucur [Thu, 30 Apr 2020 13:00:14 +0000 (16:00 +0300)]
configs: enable DM_ETH support for P2041RDB

Enable DM_ETH on all the defconfigs for the P2041RDB board.

Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
4 years agopowerpc: dts: add QorIQ DPAA 1 FMan v3 to T1024RDB
Madalin Bucur [Thu, 30 Apr 2020 13:00:13 +0000 (16:00 +0300)]
powerpc: dts: add QorIQ DPAA 1 FMan v3 to T1024RDB

Introduce the QorIQ DPAA 1 Frame Manager nodes in the T1024RDB
device tree. The device tree fragments are copied over with little
modification from the Linux kernel source code.

Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
4 years agopowerpc: dts: add QorIQ DPAA 1 FMan v3 for T102x
Madalin Bucur [Thu, 30 Apr 2020 13:00:12 +0000 (16:00 +0300)]
powerpc: dts: add QorIQ DPAA 1 FMan v3 for T102x

Add the QorIQ DPAA 1 Frame Manager v3 device tree nodes for the
T102x SoCs. The device tree fragments are copied over with little
modification from the Linux kernel source code.

Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
4 years agopowerpc: dts: add QorIQ DPAA 1 FMan to P5040DS
Madalin Bucur [Thu, 30 Apr 2020 13:00:11 +0000 (16:00 +0300)]
powerpc: dts: add QorIQ DPAA 1 FMan to P5040DS

Introduce the QorIQ DPAA 1 Frame Manager nodes in the P5040DS
device tree. The device tree fragments are copied over with little
modification from the Linux kernel source code.

Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
4 years agopowerpc: dts: add QorIQ DPAA 1 FMan for P5040
Madalin Bucur [Thu, 30 Apr 2020 13:00:10 +0000 (16:00 +0300)]
powerpc: dts: add QorIQ DPAA 1 FMan for P5040

The device tree fragments are copied over with little
modification from the Linux kernel source code.

Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
4 years agopowerpc: dts: add QorIQ DPAA 1 FMan to P3041DS
Madalin Bucur [Thu, 30 Apr 2020 13:00:09 +0000 (16:00 +0300)]
powerpc: dts: add QorIQ DPAA 1 FMan to P3041DS

Introduce the QorIQ DPAA 1 Frame Manager nodes in the P3041DS
device tree. The device tree fragments are copied over with little
modification from the Linux kernel source code.

Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
4 years agopowerpc: dts: add QorIQ DPAA 1 FMan for P3041
Madalin Bucur [Thu, 30 Apr 2020 13:00:08 +0000 (16:00 +0300)]
powerpc: dts: add QorIQ DPAA 1 FMan for P3041

The device tree fragments are copied over with little
modification from the Linux kernel source code.

Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
4 years agopowerpc: dts: add QorIQ DPAA 1 FMan to P2041RDB
Madalin Bucur [Thu, 30 Apr 2020 13:00:07 +0000 (16:00 +0300)]
powerpc: dts: add QorIQ DPAA 1 FMan to P2041RDB

Introduce the QorIQ DPAA 1 Frame Manager nodes in the P2041RDB
device tree. The device tree fragments are copied over with little
modification from the Linux kernel source code.

Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
4 years agopowerpc: dts: add QorIQ DPAA 1 FMan for P2041
Madalin Bucur [Thu, 30 Apr 2020 13:00:06 +0000 (16:00 +0300)]
powerpc: dts: add QorIQ DPAA 1 FMan for P2041

The device tree fragments are copied over with little
modification from the Linux kernel source code.

Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
4 years agopowerpc: dts: add QorIQ DPAA 1 FMan interfaces to P4080DS
Madalin Bucur [Thu, 30 Apr 2020 13:00:05 +0000 (16:00 +0300)]
powerpc: dts: add QorIQ DPAA 1 FMan interfaces to P4080DS

Introduce the QorIQ DPAA 1 Frame Manager interfaces nodes in the
P4080DS device tree.

Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
4 years agopowerpc: dts: add QorIQ DPAA 1 FMan for P4080
Madalin Bucur [Thu, 30 Apr 2020 13:00:04 +0000 (16:00 +0300)]
powerpc: dts: add QorIQ DPAA 1 FMan for P4080

The device tree fragments are copied over with little
modification from the Linux kernel source code.

Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
4 years agopowerpc: dts: add QorIQ DPAA 1 FMan v3 device tree nodes
Madalin Bucur [Thu, 30 Apr 2020 13:00:03 +0000 (16:00 +0300)]
powerpc: dts: add QorIQ DPAA 1 FMan v3 device tree nodes

Add the QorIQ DPAA Frame Manager version 3 device tree nodes
description. The device tree fragments are copied over with little
modification from the Linux kernel source code.

Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
4 years agopowerpc: dts: add QorIQ DPAA 1 FMan device tree nodes
Madalin Bucur [Thu, 30 Apr 2020 13:00:02 +0000 (16:00 +0300)]
powerpc: dts: add QorIQ DPAA 1 FMan device tree nodes

Add the QorIQ DPAA Frame Manager device tree nodes description.
The device tree fragments are copied over with little modification
from the Linux kernel source code.

Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
4 years agopowerpc: dts: add QorIQ GPIOs
Madalin Bucur [Thu, 30 Apr 2020 13:00:01 +0000 (16:00 +0300)]
powerpc: dts: add QorIQ GPIOs

Add the QorIQ GPIO device tree nodes description. The device tree
fragments are copied over with little modification from the Linux
kernel source code.

Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
4 years agopowerpc: dts: QorIQ: Add node(s) for the platform PLL
Madalin Bucur [Thu, 30 Apr 2020 13:00:00 +0000 (16:00 +0300)]
powerpc: dts: QorIQ: Add node(s) for the platform PLL

Add the QorIQ clock control device nodes include files.

Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
4 years agonet: tsec: fsl_mdio: add DM MDIO support
Madalin Bucur [Thu, 30 Apr 2020 12:59:59 +0000 (15:59 +0300)]
net: tsec: fsl_mdio: add DM MDIO support

Allow the MDIO devices to be probed based on the device tree.

Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
4 years agoriscv: sbi: Move sbi_probe_extension() out of CONFIG_SBI_V01
Bin Meng [Wed, 27 May 2020 09:04:53 +0000 (02:04 -0700)]
riscv: sbi: Move sbi_probe_extension() out of CONFIG_SBI_V01

sbi_probe_extension() is an API defined in SBI v0.2, not v0.1.

Fixes 7e249bc13aaf: ("riscv: Move all SMP related SBI calls to SBI_v01")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
4 years agoriscv: sbi: Remove sbi_spec_version
Bin Meng [Wed, 27 May 2020 09:04:52 +0000 (02:04 -0700)]
riscv: sbi: Remove sbi_spec_version

U-Boot defaults to use SBI v0.2. Howerver there is a global variable
sbi_spec_version that stills refers to v0.1. Since it is not used
anywhere, let's remove it.

Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>