orinoco: Specify all three parameters to every Hermes command.

hermes_issue_cmd now takes two more parameters.

Signed-off-by: David Kilroy <kilroyd@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

orinoco: Update scan translation

Report channel, beacon interval and capabilities.
Use WEXT defines instead of magic numbers.
State quality stats in dB.
Also a few changes to keep line length less than 80.

Signed-off-by: David Kilroy <kilroyd@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

orinoco: Add ESSID specific scanning for Agere fw

Pass the ESSID to the card.

This allows 'iwlist eth1 scan essid <essid>' to work, and will help
with routers setup not to broadcast the ESSID.

Signed-off-by: David Kilroy <kilroyd@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: add direct probe before association

This patch adds a direct probe request as first step in the association
flow if data we have is not up to date. Motivation of this step is to make
sure that the bss information we have is correct, since last scan could
have been done a while ago, and beacons do not fully answer this need as
there are potential differences between them and probe responses (e.g.
WMM parameter element)

Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

p54: rename prism54xyz -> p54xyz

It's been a long time, but fullmac prism54 driver is still around...
I think we should rename every prism54* in order to avoid some
confusion about "what is actually what" in the future ;-).

Thanks-to: Maxi <maxi@daemonizer.de>

Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: change number of pre-assoc scans

This patch fixes noticed problem in noisy environments of 50+ APs
that scan fails to find the requested AP on first try, which
leads to connection refusal. second scan has empirically proven to fix
this problem in almost all cases.

Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Esti Kummer <ester.kummer@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Add module parameter to disable HW crypto

Add a module parameter to rt61 and rt73 to disable
HW crypto. The option should only be checked when
determining if the SUPPORT_HW_CRYPTO flag should
be set or not.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Move lna_gain calculation to config() callback

We can optimize lna calculation in IRQ context by
calculating most of the value during the config() callback
when most of the value is actually influenced.

This will be required later by rt2800pci and rt2800usb as
well, since they need the lna_gain value during config().

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: cleanup mlme state namespace

This patch move add STA_MLME to station mlme state defines.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: set short preamble flag for rx

set the short preamble flag in ieee80211_rx_status for frames received with a
short preamble.

drivers/net/wireless/ath5k/base.c:      Changes-licensed-under: 3-Clause-BSD

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Release rt2x00 2.2.0

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Gather channel information in structure

Channel information which is read from EEPROM should
be read into an array containing per-channel information.
This removes the requirement of multiple arrays and makes
the channel handling a bit cleaner and easier to expand.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Implement HW encryption (rt73usb)

rt73usb supports hardware encryption.
rt73usb supports up to 4 shared keys and up to 64 pairwise keys.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Implement HW encryption (rt61pci)

rt61pci supports hardware encryption.
rt61pci supports up to 4 shared keys and up to 64 pairwise keys.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Implement HW encryption

Various rt2x00 devices support hardware encryption.

Most of them require the IV/EIV to be generated by mac80211,
but require it to be provided seperately instead of within
the frame itself. This means that rt2x00lib should extract
the data from the frame and place it in the frame descriptor.
During RX the IV/EIV is provided in the descriptor by the
hardware which means that it should be inserted into the
frame by rt2x00lib.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: filter probes in ieee80211_rx_mgmt_probe_resp

This patch moves filtering statement from ieee80211_rx_bss_info
which is called for both beacon and probe to ieee80211_rx_mgmt_probe_resp
and save few cycles in beacon parsing.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

replace net_device arguments with ieee80211_{local,sub_if_data} as appropriate

This patch replaces net_device arguments to mac80211 internal functions
with ieee80211_{local,sub_if_data} as appropriate.

It also does the same for many 802.11s mesh functions, and changes the
mesh path table to be indexed on sub_if_data rather than net_device.

If the mesh part needs to be a separate patch let me know, but since
mesh uses a lot of mac80211 functions which were being converted anyway,
the changes go hand-in-hand somewhat.

This patch probably does not convert all the functions which could be
converted, but it is a large chunk and followup patches will be
provided.

Signed-off-by: Jasper Bryant-Greene <jasper@amiton.co.nz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

move ETH_P_PAE from ieee80211_i.h to if_ether.h

ETH_P_PAE belongs in if_ether.h with the other ETH_P_* definitions. This
patch moves it there.

Signed-off-by: Jasper Bryant-Greene <jasper@amiton.co.nz>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rfkill: introduce RFKILL_STATE_MAX

While it is interesting to not add last-enum-markers because it allows gcc
to warn us of switch() statements missing a valid state, we really should
be handling memory corruption on a rfkill state with default clauses,
anyway.

So add RFKILL_STATE_MAX and use it where applicable.  It makes for safer
code in the long run.

Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rfkill: add __must_check annotations

rfkill is not a small, mere detail in wireless support.  Once it starts
supporting rfkill and users start counting on that support, a wireless
device is at risk of operating in dangerous conditions should rfkill
support fail to properly activate.

Therefore, add the required __must_check annotations on some key functions
of the rfkill API, for which the wireless drivers absolutely MUST handle
the failure mode safely in order to avoid a potentially dangerous situation
where the wireless transmitter is left enabled when the user don't want it
to.

Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rfkill: add default global states (v2)

Add a second set of global states, "rfkill_default_states", to track the
state that will be used when the first rfkill class of a given type is
registered, and also to save "undo" information when rfkill_epo is called.

Add a new exported function, rfkill_set_default(), which can be used by
platform drivers to restore radio state saved by the platform across
reboots or shutdown.

Also, fix rfkill_epo to properly update rfkill_states, but still preserve a
copy of the state so that we can undo the effect of rfkill_epo later if we
want to.  Add rfkill_restore_states() to restore rfkill_states from the
copy.

Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rfkill: detect bogus double-registering (v2)

Detect and abort with -EEXIST if rfkill_register is called twice on the
same rfkill struct.  And WARN_ON(it) for good measure.

While at it, flag when we are adding the first switch of a type, we will
need that information later.

Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: replace __FUNCTION__ with __func__

__FUNCTION__ is gcc-specific, use __func__

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas_tf: config and makefile

Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas_tf: usb specific functions

The libertas thin firmware only supports usb devices, but the usb functions have
been kept separate to ease future support for other devices.

Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas_tf: command helper functions for libertas_tf

Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas_tf: main.c, data paths and mac80211 handlers

This patch contains most of the libertastf driver, just lacking command helper
functions and usb specific functions. Currently, monitor, managed, ap and mesh
interfaces are supported. Even though this driver supports the same hardware as
the "libertas" driver, it uses a different (thin) firmware, that makes it
suitable for a mac80211 driver.

Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas_tf: header file

Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: allow no mac address until firmware load

Originally by Johannes Berg. This patch adds support for devices that do not
report their MAC address until the firmware is loaded. While the address is not
known, a multicast on is used.

Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: remove WLAN_FC_DATA_PRESENT

All users are gone now.

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: remove rx/tx_data->fc member

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: use ieee80211 frame control directly

Remove the last users of the rx/tx_data->fc data members and use the
le16 frame_control from the header directly.

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: remove IEEE80211_FC helper

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: remove ieee80211_get_hdrlen

All users have been moved over to the version taking a le16 frame control
rather than a cpu-endian value.

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: rx.c/tx.c remove more users of tx/rx_data->fc

Those functions that still use ieee80211_get_hdrlen are moved over
to use the little endian frame control.

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: wep.c replace magic numbers in IV/ICV removal

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: wme.h remove unused QOS_CONTROL_LEN

linux/ieee80211.h now has IEEE80211_QOS_CTL_LEN for this purpose.

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: explicitly check skb->len

ieee80211_get_hdrlen_from_skb internally checks the skb is long enough to
hold the full ieee80211_hdr, else it returns zero.  Use ieee80211_hdrlen
which always returns the hdrlen and check the remaining room in the
skb explicitly when removing encryption headers or the qos control field.

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: explicitly check skb->len

ieee80211_get_hdrlen_from_skb internally checks that the skb is long
enough to hold the full header, or it returns 0 if not.  The check in
ath5k does not check this case and assumes it always got the actual
header length which it then checks against the skb->len plus some headroom.

Change to ieee80211_hdrlen which always returns the hdrlen and keep the
existing headroom check.

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: use le16 frame control directly, use QOS symbolic constant mask

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43legacy: use le16 frame control directly, avoid byteswapping

Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: add level for debugging host command

This patch adds another level for debugging host command. This adds an
option to suppress the debug prints for sensitivity and link quality
commands.

Signed-off-by: Esti Kummer <ester.kummer@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: kill struct iwl4965_lq_mngr

This patch removes struct iwl4965_lq_mngr it is not used.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl-4965: test below 0 on unsigned num_tbs

num_tbs is unsigned so the test doesn't work.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: use generic mac80211 radiotap headers

remove drivers own implementation of radiotap in favor of the generic one
provided by mac80211.

also remove priv->add_radiotap because it is not used any more.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: radiotap: assume modulation from rates

use the rates ERP flag to derive CCK or OFDM modulation for the radiotap
header.

(it might be more correct to get this information from the hardware itself, but it
seems safe to assume this in most practical cases.)

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: add rx status flag for short preamble

and use it for the radiotap header

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: rates cleanup

cleanup the rates structures used by ath5k. instead of separate driver and
mac80211 rate structures we now setup a static ieee80211_rate array and use it
directly. no conversion between two different rate structures has to be done
any more. a lot of unused and confusing junk was deleted.

renamed ath5k_getchannels into ath5k_setup_bands because this is what it does.
rewrote it to copy the bitrates correctly for each band. this is necessary for
running different hardware with the same driver (e.g. 5211 and 5212 based
cards).

add special handling of rates for AR5211 chipsets: it uses different rate codes
for CCK rates (which are actually like the other chips but with a 0xF mask).

setup a hardware code to rate index reverse mapping table for getting the rate
index of received frames.

the rates for control frames which have to be set in
ath5k_hw_write_rate_duration are now in one single array.

drivers/net/wireless/ath5k/ath5k.h:     Changes-licensed-under: ISC
drivers/net/wireless/ath5k/base.c:      Changes-licensed-under: 3-Clause-BSD
drivers/net/wireless/ath5k/base.h:      Changes-licensed-under: 3-Clause-BSD
drivers/net/wireless/ath5k/hw.c:        Changes-licensed-under: ISC

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: add ieee80211_queue_stopped)

This patch adds ieee80211_queue_stopped that let drivers to query
queue status

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

WIRELESS: Make wireless one-click selectable.

Use "menuconfig" to make wireless support one-click selectable.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Ath5k: unify resets

There were 3 code copy and pastes of reset. Unify the resets and place
in separate function.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00mac: In error case stop netdev queue, free skb and return NETDEV_TX_OK

It is not allowed to use NETDEV_TX_BUSY in tx path anymore.

Signed-off-by: Daniel Wagner <wagi@monom.org>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: add Mesh Point support

This enables draft-802.11s Mesh Point operation.  For that we need mesh
beaconing.  Tested with AR5212/AR5213 PCI card against Zydas and b43 mesh
nodes.

Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

net/ieee80211: adjust error handling

Converts a test in error handling code to a sequence of labels.

The semantic match that found the problem is:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
expression E,E1,E2;
@@

E = alloc_etherdev(...)
... when != E = E1
if (...) { ... free_netdev(E); ... return ...; }
... when != E = E2
(
  if (...)
   {
   ... when != free_netdev(E);
   return dev; }
|
* if (...)
   {
   ... when != free_netdev(E);
   return ...; }
|
register_netdev(E)
)

// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: add sysfs hooks to update boot2 and persistent firmware

To use these features, copy the boot2 and firmware images to /lib/firmware and:

echo <boot2_image_name> > /sys/class/net/ethX/lbs_flash_boot2
echo <firmware_image_name> > /sys/class/net/ethX/lbs_flash_fw

Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: support boot commands to write persistent firmware and bootloader

Add locking and non-locking versions of if_usb_prog_firmware to support
programming firmware after and before driver bring-up respectively.  Add more
suitable error codes for firmware programming process.  Add capability checks
for persistent features before attempting to use them.

Based on patches from Brajesh Dave and Priyank Singh.

Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtl818x: merge tx/rx descriptor flags

Tx/Rx descriptor flags are common between rtl818x devices, only with
additions for newer chips, thus use same flags in the code.

Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

pkt_sched: Fix qdisc_watchdog() vs. dev_deactivate() race

dev_deactivate() can skip rescheduling of a qdisc by qdisc_watchdog()
or other timer calling netif_schedule() after dev_queue_deactivate().
We prevent this checking aliveness before scheduling the timer. Since
during deactivation the root qdisc is available only as qdisc_sleeping
additional accessor qdisc_root_sleeping() is created.

With feedback from Herbert Xu <herbert@gondor.apana.org.au>

Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: fix potential panics in the SCTP-AUTH API.

All of the SCTP-AUTH socket options could cause a panic
if the extension is disabled and the API is envoked.

Additionally, there were some additional assumptions that
certain pointers would always be valid which may not
always be the case.

This patch hardens the API and address all of the crash
scenarios.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Linux v2.6.27-rc4

cramfs: fix named-pipe handling

After commit a97c9bf33f4612e2aed6f000f6b1d268b6814f3c (fix cramfs
making duplicate entries in inode cache) in kernel 2.6.14, named-pipe
on cramfs does not work properly.

It seems the commit make all named-pipe on cramfs share their inode
(and named-pipe buffer).

Make ..._test() refuse to merge inodes with ->i_ino == 1, take inode setup
back to get_cramfs_inode() and make ->drop_inode() evict ones with ->i_ino
== 1 immediately.

Reported-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@kernel.org> [2.6.14 and later]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fbdefio: add set_page_dirty handler to deferred IO FB

Fixes kernel BUG at lib/radix-tree.c:473.

Previously the handler was incidentally provided by tmpfs but this was
removed with:

  commit 14fcc23fdc78e9d32372553ccf21758a9bd56fa1
  Author: Hugh Dickins <hugh@veritas.com>
  Date:   Mon Jul 28 15:46:19 2008 -0700

    tmpfs: fix kernel BUG in shmem_delete_inode

relying on this behaviour was incorrect in any case and the BUG also
appeared when the device node was on an ext3 filesystem.

v2: override a_ops at open() time rather than mmap() time to minimise
races per AKPM's concerns.

Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Jaya Kumar <jayakumar.lkml@gmail.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Johannes Weiner <hannes@saeurebad.de>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Kel Modderman <kel@otaku42.de>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: <stable@kernel.org> [14fcc23fd is in 2.6.25.14 and 2.6.26.1]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: rtc-ds1374: fix 'no irq' case handling

On a PowerPC board with ds1374 RTC I'm getting this error while RTC tries
to probe:

rtc-ds1374 0-0068: unable to request IRQ

This happens because I2C probing code (drivers/of/of_i2c.c) is specifying
IRQ0 for 'no irq' case, which is correct.

The driver handles this incorrectly, though. This patch fixes it.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: xip/ext2 fix block allocation race

XIP can call into get_xip_mem concurrently with the same file,offset with
create=1.  This usually maps down to get_block, which expects the page
lock to prevent such a situation.  This causes ext2 to explode for one
reason or another.

Serialise those calls for the moment.  For common usages today, I suspect
get_xip_mem rarely is called to create new blocks.  In future as XIP
technologies evolve we might need to look at which operations require
scalability, and rework the locking to suit.

Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Jared Hulbert <jaredeh@gmail.com>
Acked-by: Carsten Otte <cotte@freenet.de>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: xip fix fault vs sparse page invalidate race

XIP has a race between sparse pages being inserted into page tables, and
sparse pages being zapped when its time to put a non-sparse page in.

What can happen is that a process can be left with a dangling sparse page
in a MAP_SHARED mapping, while the rest of the world sees the non-sparse
version.  Ie.  data corruption.

Guard these operations with a seqlock, making fault-in-sparse-pages the
slowpath, and try-to-unmap-sparse-pages the fastpath.

Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Jared Hulbert <jaredeh@gmail.com>
Acked-by: Carsten Otte <cotte@freenet.de>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: dirty page tracking race fix

There is a race with dirty page accounting where a page may not properly
be accounted for.

clear_page_dirty_for_io() calls page_mkclean; then TestClearPageDirty.

page_mkclean walks the rmaps for that page, and for each one it cleans and
write protects the pte if it was dirty.  It uses page_check_address to
find the pte.  That function has a shortcut to avoid the ptl if the pte is
not present.  Unfortunately, the pte can be switched to not-present then
back to present by other code while holding the page table lock -- this
should not be a signal for page_mkclean to ignore that pte, because it may
be dirty.

For example, powerpc64's set_pte_at will clear a previously present pte
before setting it to the desired value.  There may also be other code in
core mm or in arch which do similar things.

The consequence of the bug is loss of data integrity due to msync, and
loss of dirty page accounting accuracy.  XIP's __xip_unmap could easily
also be unreliable (depending on the exact XIP locking scheme), which can
lead to data corruption.

Fix this by having an option to always take ptl to check the pte in
page_check_address.

It's possible to retain this optimization for page_referenced and
try_to_unmap.

Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Jared Hulbert <jaredeh@gmail.com>
Cc: Carsten Otte <cotte@freenet.de>
Cc: Hugh Dickins <hugh@veritas.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fix setpriority(PRIO_PGRP) thread iterator breakage

When user calls sys_setpriority(PRIO_PGRP ...) on a NPTL style multi-LWP
process, only the task leader of the process is affected, all other
sibling LWP threads didn't receive the setting.  The problem was that the
iterator used in sys_setpriority() only iteartes over one task for each
process, ignoring all other sibling thread.

Introduce a new macro do_each_pid_thread / while_each_pid_thread to walk
each thread of a process.  Convert 4 call sites in {set/get}priority and
ioprio_{set/get}.

Signed-off-by: Ken Chen <kenchen@google.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Roland McGrath <roland@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Video/Framebuffer: add fuctional power management support to Blackfin BF54x LQ043 framebuffer driver

Fix bug: does nor properply resume after suspend mem
Fix for PM_SUSPEND_MEM: Save and restore peripheral base and DMA registers

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

bootmem: fix aligning of node-relative indexes and offsets

Absolute alignment requirements may never be applied to node-relative
offsets.  Andreas Herrmann spotted this flaw when a bootmem allocation on
an unaligned node was itself not aligned because the combination of an
unaligned node with an aligned offset into that node is not garuanteed to
be aligned itself.

This patch introduces two helper functions that align a node-relative
index or offset with respect to the node's starting address so that the
absolute PFN or virtual address that results from combining the two
satisfies the requested alignment.

Then all the broken ALIGN()s in alloc_bootmem_core() are replaced by these
helpers.

Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Reported-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Debugged-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Reviewed-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Tested-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/char/ipmi/ipmi_si_intf.c:default_find_bmc(): fix leak

If check_legacy_ioport() returns true, we leak *info.

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11362

Reported-by: Daniel Marjamki <danielm77@spray.se>
Cc: Christian Krafft <krafft@de.ibm.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Corey Minyard <minyard@acm.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pm2fb: free cmap memory on module remove

Release cmap memory allocated in the probe function.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: fix double lock on UIE emulation

With commit 5ad31a575157147b43fa84ef1e21471661653878 ("rtc: remove BKL
for ioctl()"), RTC_UIE_ON ioctl cause double lock on rtc->ops_lock.
The ops_lock must not be held while set_uie() calls rtc_read_time()
which takes the lock.  Also clear_uie() does not need ops_lock.  This
patch fixes return value of RTC_UIE_OFF ioctl too.

Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: David Brownell <david-b@pacbell.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

binfmt_misc: fix false -ENOEXEC when coupled with other binary handlers

In case the binfmt_misc binary handler is registered *before* the e.g.
script one (when for example being compiled as a module) the following
situation may occur:

1. user launches a script, whose interpreter is a misc binary;
2. the load_misc_binary sets the misc_bang and returns -ENOEVEC,
   since the binary is a script;
3. the load_script_binary loads one and calls for search_binary_hander
   to run the interpreter;
4. the load_misc_binary is called again, but refuses to load the
   binary due to misc_bang bit set.

The fix is to move the misc_bang setting lower - prior to the actual
call to the search_binary_handler.

Caused by the commit 3a2e7f47 (binfmt_misc.c: avoid potential kernel
stack overflow)

Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reported-by: Kirill A. Shutemov <kirill@shutemov.name>
Tested-by: Kirill A. Shutemov <kirill@shutemov.name>
Cc: <stable@kernel.org> [2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

brd: fix name argument of unregister_blkdev()

The name of brd block device is "ramdisk", it's not "brd".
(The block device is registered by register_blkdev(RAMDISK_MAJOR, "ramdisk")
So it should be unregistered by unregister_blkdev(RAMDISK_MAJOR, "ramdisk")

Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

nbd: fix memory leak of nbd_dev array

We leak the memory allocated for the nbd_dev array at multiple places.
Fix them by either adding a kfree() or by rearranging code to return
before we allocate the memory.

Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Cc: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: mminit_loglevel cannot be __meminitdata anymore

mminit_loglevel is now used from mminit_verify_zonelist <- build_all_zonelists <-

1. online_pages <- memory_block_action <- memory_block_change_state <- store_mem_state (sys handler)
2. numa_zonelist_order_handler (proc handler)

so it cannot be annotated __meminit - drop it

fixes following section mismatch warning:
WARNING: vmlinux.o(.text+0x71628): Section mismatch in reference from the function mminit_verify_zonelist() to the variable .meminit.data:mminit_loglevel
The function mminit_verify_zonelist() references
the variable __meminitdata mminit_loglevel.
This is often because mminit_verify_zonelist lacks a __meminitdata
annotation or the annotation of mminit_loglevel is wrong.

Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: show free swap as signed

Adjust <Alt><SysRq>m show_swap_cache_info() to show "Free swap" as a
signed long: the signed format is preferable, because during swapoff
nr_swap_pages can legitimately go negative, so makes more sense thus
(it used to be shown redundantly, once as signed and once as unsigned).

Signed-off-by: Hugh Dickins <hugh@veritas.com>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: page_remove_rmap comments on PageAnon

Add a comment to s390's page_test_dirty/page_clear_dirty/page_set_dirty
dance in page_remove_rmap(): I was wrong to think the PageSwapCache test
could be avoided, and would like a comment in there to remind me.  And
mention s390, to help us remember that this block is not really common.

Also move down the "It would be tidy to reset PageAnon" comment: it does
not belong to s390's block, and it would be unwise to reset PageAnon
before we're done with testing it.

Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Blackfin RTC Driver: dont let RTC programming in bootloaders randomly cause ~5 second boot delays

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Blackfin RTC Driver: BF561 not have on-chip RTC

Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Blackfin RTC Driver: do all initialization before we register the rtc and make it available

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Blackfin RTC Driver: move irq request/free out of open/release and into probe/remove so that the non-dev interfaces (like sysfs) work as expected

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

/proc/self/maps doesn't display the real file offset

This addresses

http://bugzilla.kernel.org/show_bug.cgi?id=11318

In function show_map (file: fs/proc/task_mmu.c), if vma->vm_pgoff > 2^20
than (vma->vm_pgoff << PAGE_SIZE) is greater than 2^32 (with PAGE_SIZE
equal to 4096 (i.e.  2^12).  The next seq_printf use an unsigned long for
the conversion of (vma->vm_pgoff << PAGE_SIZE), as a result the offset
value displayed in /proc/self/maps is truncated if the page offset is
greater than 2^20.

A test that shows this issue:

#define _GNU_SOURCE
#include <sys/types.h>
#include <sys/stat.h>
#include <sys/mman.h>
#include <stdlib.h>
#include <stdio.h>
#include <fcntl.h>
#include <unistd.h>
#include <string.h>

#define PAGE_SIZE (getpagesize())

#if __i386__
#   define U64_STR "%llx"
#elif __x86_64
#   define U64_STR "%lx"
#else
#   error "Architecture Unsupported"
#endif

int main(int argc, char *argv[])
{
int fd;
char *addr;
off64_t offset = 0x10000000;
char *filename = "/dev/zero";

fd = open(filename, O_RDONLY);
if (fd < 0) {
perror("open");
return 1;
}

offset *= 0x10;
printf("offset = " U64_STR "\n", offset);

addr = (char*)mmap64(NULL, PAGE_SIZE, PROT_READ, MAP_PRIVATE, fd,
     offset);
if ((void*)addr == MAP_FAILED) {
perror("mmap64");
return 1;
}

{
FILE *fmaps;
char *line = NULL;
size_t len = 0;
ssize_t read;
size_t filename_len = strlen(filename);

fmaps = fopen("/proc/self/maps", "r");
if (!fmaps) {
perror("fopen");
return 1;
}
while ((read = getline(&line, &len, fmaps)) != -1) {
if ((read > filename_len + 1)
    && (strncmp(&line[read - filename_len - 1], filename, filename_len) == 0))
printf("%s", line);
}

if (line)
free(line);

fclose(fmaps);
}

close(fd);
return 0;
}

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Clement Calmels <cboulte@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

documentation: describe bootmem_debug kernel parameter

"bootmem_debug" is not mentioned in kernel-parameters.txt. Recently I
had to use that kernel option and I think it should be documented.

Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Johannes Weiner <hannes@saeurebad.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

eeepc-laptop: fix use after free

eeepc-laptop uses the hwmon struct after unregistering the device, causing
an oops on module unload.  Flip the ordering to fix.

Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Karol Kozimor <sziwan@users.sourceforge.net>
Cc: <stable@kernel.org> [2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

FRV: Provide ioremap_wc() for FRV

Provide ioremap_wc() for FRV.

Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

MN10300: Supply ioremap_wc() for MN10300

Supply ioremap_wc() for MN10300.

Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Reserve NFS fileid values for btrfs

Purely cosmetic for now, but we might as well get it merged ASAP.

Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Reduce brokenness of CRIS headers_install

I won't say 'fix', because they still look broken, although this will at
least allow 'make ARCH=CRIS headers_install' to _complete_.

For headers which are exported, we should probably choose between
asm/arch-v10 and asm/arch-v32 by something that GCC defines -- we can't
rely on a generated symlink. And we certainly can't export an arch/
directory which doesn't even exist.

And the only thing that we seem to include from the arch/ directory is
<asm/arch/ptrace.h> from <asm/ptrace.h> ... and that isn't exported in
either arch-v10 or arch-v32 _anyway_.

Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'sh/for-2.6.27' of git://git./linux/kernel/git/lethal/sh-2.6

* 'sh/for-2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  sh: Provide a FLAT_PLAT_INIT() definition.
  binfmt_flat: Stub in a FLAT_PLAT_INIT().
  video: export sh_mobile_lcdc panel size
  sh: select memchunk size using kernel cmdline
  sh: export sh7723 VEU as VEU2H
  input: migor_ts compile and detection fix
  sh: remove MSTPCR defines from Migo-R header file
  sh: Update sh7763rdp defconfig
  sh: Add support sh7760fb to sh7763rdp board
  sh: Add support sh_eth to sh7763rdp board
  sh: Disable 64kB hugetlbpage size when using 64kB PAGE_SIZE.
  sh: Don't export __{s,u}divsi3_i4i from SH-2 libgcc.
  fix SH7705_CACHE_32KB compilation
  sh: mach-x3proto: Fix up smc91x platform data.

Merge branch 'merge' of git://git./linux/kernel/git/paulus/powerpc

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
  powerpc: Fix vio_bus_probe oops on probe error
  powerpc/ibmebus: Restore "name" sysfs attribute on ibmebus devices
  powerpc: Fix /dev/oldmem interface for kdump
  powerpc/spufs: Remove invalid semicolon after if statement
  powerpc/spufs: reference context while dropping state mutex in scheduler
  powerpc/spufs: fix npc setting for NOSCHED contexts

Merge branch 'tracehook' of git://git./linux/kernel/git/frob/linux-2.6-utrace

* 'tracehook' of git://git.kernel.org/pub/scm/linux/kernel/git/frob/linux-2.6-utrace:
  tracehook: fix SA_NOCLDWAIT

Merge git://git./linux/kernel/git/jejb/scsi-rc-fixes-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (22 commits)
  [SCSI] ibmvfc: Driver version 1.0.2
  [SCSI] ibmvfc: Add details to async event log
  [SCSI] ibmvfc: Sanitize response lengths
  [SCSI] ibmvfc: Fix for lost async events
  [SCSI] ibmvfc: Fixup host state during reinit
  [SCSI] ibmvfc: Fix another hang on module removal
  [SCSI] ibmvscsi: Fixup desired DMA value for shared memory partitions
  [SCSI] megaraid_sas: remove sysfs dbg_lvl world writeable permissions
  [SCSI] qla2xxx: Update version number to 8.02.01-k7.
  [SCSI] qla2xxx: Explicitly tear-down vports during PCI remove_one().
  [SCSI] qla2xxx: Reference proper ha during SBR handling.
  [SCSI] qla2xxx: Set npiv_supported flag for FCoE HBAs.
  [SCSI] qla2xxx: Don't leak SG-DMA mappings while aborting commands.
  [SCSI] qla2xxx: Correct vport-state management issues during ISP-ABORT.
  [SCSI] qla2xxx: Correct synchronization of software/firmware fcport states.
  [SCSI] scsi_dh: Initialize lun_state in check_ownership()
  [SCSI] scsi_dh: Do not use scsilun in rdac hardware handler
  [SCSI] megaraid_sas: version and Documentation Update
  [SCSI] megaraid_sas: add new controllers (0x78 0x79)
  [SCSI] megaraid_sas: add the shutdown DCMD cmd to driver shutdown routine
  ...

vfat: fix 'sync' mount deadlock due to BKL->lock_super conversion

There was another FAT BKL conversion deadlock reported by Bart
Trojanowski due to the BKL being used as a recursive lock by FAT, which
was missed because it only triggers with 'sync' (or 'dirsync') mounts.

The recursion worked for the BKL, but after the conversion to lock_super
(which uses a mutex), it just deadlocks.

Thanks to Bart for debugging this and testing the fix.  The lock
debugging information from the original report:

  =============================================
  [ INFO: possible recursive locking detected ]
  2.6.27-rc3-bisect-00448-ga7f5aaf #16
  ---------------------------------------------
  mv/4020 is trying to acquire lock:
   (&type->s_lock_key#9){--..}, at: [<c01a90fe>] lock_super+0x1e/0x20

  but task is already holding lock:
   (&type->s_lock_key#9){--..}, at: [<c01a90fe>] lock_super+0x1e/0x20

  other info that might help us debug this:
  3 locks held by mv/4020:
   #0:  (&sb->s_type->i_mutex_key#9/1){--..}, at: [<c01b2336>] do_unlinkat+0x66/0x140
   #1:  (&sb->s_type->i_mutex_key#9){--..}, at: [<c01b0954>] vfs_unlink+0x84/0x110
   #2:  (&type->s_lock_key#9){--..}, at: [<c01a90fe>] lock_super+0x1e/0x20

  stack backtrace:
  Pid: 4020, comm: mv Not tainted 2.6.27-rc3-bisect-00448-ga7f5aaf #16
   [<c014e694>] validate_chain+0x984/0xea0
   [<c0108d70>] ? native_sched_clock+0x0/0xf0
   [<c014ee9c>] __lock_acquire+0x2ec/0x9b0
   [<c014f5cf>] lock_acquire+0x6f/0x90
   [<c01a90fe>] ? lock_super+0x1e/0x20
   [<c044e5fd>] mutex_lock_nested+0xad/0x300
   [<c01a90fe>] ? lock_super+0x1e/0x20
   [<c01a90fe>] ? lock_super+0x1e/0x20
   [<c01a90fe>] lock_super+0x1e/0x20
   [<f8b3a700>] fat_write_inode+0x60/0x2b0 [fat]
   [<c0450878>] ? _spin_unlock_irqrestore+0x48/0x80
   [<f8b3a953>] ? fat_sync_inode+0x3/0x20 [fat]
   [<f8b3a962>] fat_sync_inode+0x12/0x20 [fat]
   [<f8b37c7e>] fat_remove_entries+0xbe/0x120 [fat]
   [<f8b422ef>] vfat_unlink+0x5f/0x90 [vfat]
   [<f8b42290>] ? vfat_unlink+0x0/0x90 [vfat]
   [<c01b0968>] vfs_unlink+0x98/0x110
   [<c01b2400>] do_unlinkat+0x130/0x140
   [<c016a8f5>] ? audit_syscall_entry+0x105/0x150
   [<c01b253b>] sys_unlinkat+0x3b/0x40
   [<c01040d3>] sysenter_do_call+0x12/0x3f
   =======================

where the deadlock is due to the nesting of lock_super from vfat_unlink
to fat_write_inode:

 - do_unlinkat
   - vfs_unlink
     - vfat_unlink
       * lock_super
       - fat_remove_entries
         - fat_sync_inode
           - fat_write_inode
             * lock_super

and the fix is to simply remove the use of lock_super() in fat_write_inode.

The lock_super() there had been just an automatic conversion of the
kernel lock to the superblock lock, but no locking was actually needed
there, since the code in fat_write_inode already protected all relevant
accesses with a spinlock (sbi->inode_hash_lock to be exact).  The only
code inside the BKL (and thus the superblock lock) was accesses tp local
variables or calls to functions that have long been SMP-safe (i.e.
sb_bread, mark_buffe_dirty and brlese).

Bart reports:
 "Looks good.  I ran 10 parallel processes creating 1M files truncating
  them, writing to them again and then deleting them.  This patch fixes
  the issue I ran into.

Signed-off-by: Bart Trojanowski <bart@jukie.net>"
Reported-and-tested-by: Bart Trojanowski <bart@jukie.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

tracehook: fix SA_NOCLDWAIT

I outwitted myself again in commit 2b2a1ff64afbadac842bbc58c5166962cf4f7664,
and broke the SA_NOCLDWAIT behavior so it leaks zombies.  This fixes it.

Reported-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Roland McGrath <roland@redhat.com>

powerpc: Fix vio_bus_probe oops on probe error

When CMO is enabled and booted on a non CMO system and the VIO
device's probe function fails, an oops can result since
vio_cmo_bus_remove is called when it should not.  This fixes it by
avoiding the vio_cmo_bus_remove call on platforms that don't implement
CMO.

cpu 0x0: Vector: 300 (Data Access) at [c00000000e13b3d0]
    pc: c000000000020d34: .vio_cmo_bus_remove+0xc0/0x1f4
    lr: c000000000020ca4: .vio_cmo_bus_remove+0x30/0x1f4
    sp: c00000000e13b650
   msr: 8000000000009032
   dar: 0
 dsisr: 40000000
  current = 0xc00000000e0566c0
  paca    = 0xc0000000006f9b80
    pid   = 2428, comm = modprobe
enter ? for help
[c00000000e13b6e0] c000000000021d94 .vio_bus_probe+0x2f8/0x33c
[c00000000e13b7a0] c00000000029fc88 .driver_probe_device+0x13c/0x200
[c00000000e13b830] c00000000029fdac .__driver_attach+0x60/0xa4
[c00000000e13b8c0] c00000000029f050 .bus_for_each_dev+0x80/0xd8
[c00000000e13b980] c00000000029f9ec .driver_attach+0x28/0x40
[c00000000e13ba00] c00000000029f630 .bus_add_driver+0xd4/0x284
[c00000000e13baa0] c0000000002a01bc .driver_register+0xc4/0x198
[c00000000e13bb50] c00000000002168c .vio_register_driver+0x40/0x5c
[c00000000e13bbe0] d0000000003b3f1c .ibmvfc_module_init+0x70/0x109c [ibmvfc]
[c00000000e13bc70] c0000000000acf08 .sys_init_module+0x184c/0x1a10
[c00000000e13be30] c000000000008748 syscall_exit+0x0/0x40

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

powerpc/ibmebus: Restore "name" sysfs attribute on ibmebus devices

Recent of_platform changes made of_bus_type_init() overwrite the bus
type's .dev_attrs list, meaning that the "name" attribute that ibmebus
devices previously had is no longer present.  This is a user-visible
regression which breaks the userspace eHCA support, since the eHCA
userspace driver relies on the name attribute to check for valid
adapters.

This fixes it by providing the "name" attribute in the generic OF
device code instead.  Tested on POWER.

Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

powerpc: Fix /dev/oldmem interface for kdump

A change to __ioremap() broke reading /dev/oldmem because we're no
longer able to ioremap pfn 0 (d177c207, "[PATCH] powerpc: IOMMU: don't
ioremap null addresses").

We actually don't need to ioremap for anything that's part of the linear
mapping, so just read it directly.

Also make sure we're only reading one page or less at a time.

Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Sachin Sant <sachinp@in.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Merge branch 'merge' of git://git./linux/kernel/git/jk/spufs into merge

Merge branch 'for-linus' of git://git./linux/kernel/git/ieee1394/linux1394-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  firewire: Kconfig help update
  ieee1394: sbp2: let nodemgr retry node updates during bus reset series
  ieee1394: don't drop nodes during bus reset series
  ieee1394: regression in 2.6.25: updates should happen before probes