Rui Paulo [Mon, 9 Nov 2009 23:46:40 +0000 (23:46 +0000)]
mac80211: set MESH_TTL to 31
Update the mesh time to live field to 31 according to draft 3.03.
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rui Paulo [Mon, 9 Nov 2009 23:46:39 +0000 (23:46 +0000)]
mac80211: update meshconf IE
This updates the Mesh Configuration IE according to the latest
draft (3.03).
Notable changes include the simplified protocol IDs.
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Mon, 9 Nov 2009 22:38:35 +0000 (23:38 +0100)]
rt2x00: Fix building of rt2800lib when rt2x00 driver is built-in.
When enabling rt2800usb as a built-in driver (as opposed to a as a module) the build fails. See
http://marc.info/?l=linux-wireless&m=
125768687711034&w=2 for details.
Fix it by properly including <linux/usb.h> from rt2x00usb.h
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Sun, 8 Nov 2009 11:30:14 +0000 (12:30 +0100)]
rt2x00: Move interface type assignments to generic code.
Make sure all drivers can benefit of the assignment of the interface
type of an adapter, instead of keeping it for rt2800 only.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Julia Lawall [Sun, 8 Nov 2009 08:23:07 +0000 (09:23 +0100)]
drivers/net/wireless: correct check on CCS_START_NETWORK
CCS_START_NETWORK is declared in drivers/net/wireless/rayctl.h with the
comment Values for cmd. status is previously compared to
CCS_COMMAND_COMPLETE, which is declared in the same file with the comment
Values for buffer_status. Finally, it is possible at this point that cmd
is CCS_START_NETWORK, because it is compared to that value in an enclosing
switch that has CCS_START_NETWORK as one of two case labels around this code.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Hutchings [Sat, 7 Nov 2009 22:03:22 +0000 (22:03 +0000)]
zd1211rw: declare MODULE_FIRMWARE
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Hutchings [Sat, 7 Nov 2009 22:02:39 +0000 (22:02 +0000)]
zd1201: declare MODULE_FIRMWARE
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Hutchings [Sat, 7 Nov 2009 22:02:15 +0000 (22:02 +0000)]
wl12xx: declare MODULE_FIRMWARE
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Hutchings [Sat, 7 Nov 2009 22:01:55 +0000 (22:01 +0000)]
prism54: declare MODULE_FIRMWARE
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Hutchings [Sat, 7 Nov 2009 22:01:29 +0000 (22:01 +0000)]
orinoco: declare MODULE_FIRMWARE
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Hutchings [Sat, 7 Nov 2009 22:00:57 +0000 (22:00 +0000)]
mwl8k: declare MODULE_FIRMWARE
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Hutchings [Sat, 7 Nov 2009 22:00:38 +0000 (22:00 +0000)]
libertas_tf_usb: declare MODULE_FIRMWARE
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Hutchings [Sat, 7 Nov 2009 22:00:03 +0000 (22:00 +0000)]
libertas: declare MODULE_FIRMWARE
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Hutchings [Sat, 7 Nov 2009 21:59:38 +0000 (21:59 +0000)]
iwmc3200wifi: declare MODULE_FIRMWARE
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Hutchings [Sat, 7 Nov 2009 21:59:10 +0000 (21:59 +0000)]
ipw2200: declare MODULE_FIRMWARE
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Hutchings [Sat, 7 Nov 2009 21:58:47 +0000 (21:58 +0000)]
ipw2100: declare MODULE_FIRMWARE
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Hutchings [Sat, 7 Nov 2009 21:58:05 +0000 (21:58 +0000)]
atmel: declare MODULE_FIRMWARE
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Hutchings [Sat, 7 Nov 2009 21:56:08 +0000 (21:56 +0000)]
at76c50x-usb: declare MODULE_FIRMWARE
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Sat, 7 Nov 2009 17:54:22 +0000 (18:54 +0100)]
b43-pio: Fix RX error path for rev>=8 devices
This fixes the RX error path for rev>=8 devices.
The wrong register size and definitions were used.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Randy Dunlap [Fri, 6 Nov 2009 23:35:15 +0000 (15:35 -0800)]
staging/wireless: don't build when NET etc. are not enabled
These wireless drivers in staging could be built when
CONFIG_NET=n, CONFIG_NETDEVICES=n, causing this build error:
net/wireless/wext-priv.c: In function 'ioctl_private_call':
net/wireless/wext-priv.c:206: error: implicit declaration of function 'call_commit_handler'
due to faulty selects.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Cahill [Fri, 6 Nov 2009 22:53:03 +0000 (14:53 -0800)]
iwlwifi: MAC_ACCESS_REQ cleanup
Add txq_id info to "Tx queue requesting wakeup" debug message
Add "Rx queue requesting wakeup" debug message
Move clear of CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ to be after nearby
iwl_write_prph(), since iwl_write_prph() sets it and clears it. Almost
removed it entirely, but just making sure in case someone removes the
iwl_write_prph()! Also remove unneeded priv->lock usage; this is now
handled by priv->reg_lock within iwl_clear_bit().
Join a couple of lines that had unneeded line returns.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 6 Nov 2009 22:53:02 +0000 (14:53 -0800)]
iwlwifi: Fix issue on file transfer stalled in HT mode
Turn on RTS/CTS for HT to prevent uCode TX fifo underrun
This is fix for
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2103
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Tested-by: Jiajia Zheng <jiajia.zheng@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Cahill [Fri, 6 Nov 2009 22:53:01 +0000 (14:53 -0800)]
iwlagn: update write pointers in iwl_irq_tasklet()
Follow-up to "update write pointers for all tx queues after wakeup"; that
patch changed iwl_irq_tasklet_legacy(), but not iwl_irq_tasklet(), so
newer devices were not covered.
Comments from original patch:
Wakeup interrupt has been updating write pointers (indexes, actually) only
for tx queues 0-5. This is adequate just for 3945, but inadequate for other
devices, all of which have more tx queues. Now updating all tx/command queues,
so device can be aware of all new tx and host commands enqueued while
device was asleep.
This can potentially improve data traffic bandwidth and/or latency.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Cahill [Fri, 6 Nov 2009 22:53:00 +0000 (14:53 -0800)]
iwlwifi: Add comments about MAC_ACCESS_REQ
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Cahill [Fri, 6 Nov 2009 22:52:59 +0000 (14:52 -0800)]
iwlwifi: Update comments for struct iwl_ssid_ie
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Cahill [Fri, 6 Nov 2009 22:52:58 +0000 (14:52 -0800)]
iwlwifi: speed up event log dumps
Take advantage of device's auto-increment for SRAM reads to eliminate extra
write address accesses.
Grab/release NIC access before/after entire read sequence, rather than for
each read individually.
After a quick check of dmesg logs, this seems to double Event Log dump speed,
reducing from about 20 milliseconds to about 10 milliseconds for 512 entries
using 3945.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Cahill [Fri, 6 Nov 2009 22:52:57 +0000 (14:52 -0800)]
iwlwifi: Limit size of Event Log dump
If device provides bad values for Event Log parameters (due to being asleep
or SRAM corruption, etc.), the size can be very, very large (e.g. 0xa5a5a5a5),
which can flood system log.
Sanity-check capacity and next_entry values and limit to reasonable size dump.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 6 Nov 2009 22:52:56 +0000 (14:52 -0800)]
iwlwifi: do not base station's sm_ps setting on AP
Do not use AP's SM_PS setting for our own SM_PS setting.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 6 Nov 2009 22:52:55 +0000 (14:52 -0800)]
iwlwifi: drop non-production PCI-IDs
Remove the support for all the PCI_IDs never make into production
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 6 Nov 2009 22:52:54 +0000 (14:52 -0800)]
iwlwifi: fix for channel switch
Different channel has different configuration, need to pass correct
configuration to uCode when send "channel switch" command to uCode.
Invalid configuration will cause sysassert in uCode and produce
un-expected result.
Even it is a very small windows, but we also need to consider and handle
the case if commit_rxon occurred before the "channel switch
announcement" notification received from uCode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 6 Nov 2009 22:52:53 +0000 (14:52 -0800)]
iwlwifi: add FIFO usage for 5000
This is part of the code, but the comment doesn't have it,
add pointers to the code and the FIFO usage for 5000 and
up.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 6 Nov 2009 22:52:52 +0000 (14:52 -0800)]
iwlwifi: remove un-used parameter
Remove un-used parameter "recovery_rxon" from "priv" data structure
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 6 Nov 2009 22:52:51 +0000 (14:52 -0800)]
iwlwifi: fix FIFO vs. queue confusion
When I added that code setting the swq_id, I evidently
did not understand the distinction between FIFO and TX
queue yet and added code to compare a queue ID and a
FIFO number, which is bogus.
However, the code there need not be this specific, it
can just set all queues to the identity mapping which
will be overwritten by the aggregation queue code. As
a bit of defensive coding, don't assign an swq_id to
the command queue so that if we ever use it for frames
we notice quickly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 6 Nov 2009 22:52:50 +0000 (14:52 -0800)]
iwlwifi: don't double-activate queue 4
The fourth queue (command queue) is already activated in
the loop above that also maps it to the command FIFO and
therefore doesn't need to be marked as activated again.
Also change the TODO comment to be accurate -- we need
to initialise the _queues_, not FIFOs, and map them to
device FIFOs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 6 Nov 2009 22:52:49 +0000 (14:52 -0800)]
iwlwifi: no periodic Tx/IQ calibration for 6x00/6x50 series
For both 6x00 and 6x50 series devices, periodic Tx IQ calibration is
disabled in uCode, driver do not need to set the periodic Tx/IQ calibration
bit in calibration command.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Shanyu Zhao [Fri, 6 Nov 2009 22:52:48 +0000 (14:52 -0800)]
iwlwifi: use configured valid rx chain for scan
Use configured valid rx chains in scan command instead of ANT_ABC, correcting
valid rx chain configuration of 4965, should be ANT_ABC instead of ANT_AB.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Shanyu Zhao [Fri, 6 Nov 2009 22:52:47 +0000 (14:52 -0800)]
iwlwifi: use only one chain for scan in PS
When doing scan in power saving mode, choose only 1 valid RX chain instead of
turning all chains on.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 6 Nov 2009 22:52:46 +0000 (14:52 -0800)]
iwlwifi: print rx_on config to help debug
To help debug rx related issues, if IWL_DEBUG_RADIO flag is set, print
the rxon configuration when rxon host command send to uCode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zhu Yi [Fri, 6 Nov 2009 22:52:45 +0000 (14:52 -0800)]
iwlwifi: allocate 128 bytes linear buffer for rx skb
Allocate 128 bytes linear buffer for rx skb. The first 64 bytes is
reserved for mac80211 usage (for radiotap header expansion, etc).
The frame header starts from the second 64 bytes.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reinette Chatre [Fri, 6 Nov 2009 22:52:44 +0000 (14:52 -0800)]
iwlwifi: change debug message to error in failure case
Since these messages indicate failure we would be interested in seeing them
always.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Fri, 6 Nov 2009 17:32:44 +0000 (18:32 +0100)]
b43: Rewrite TX bounce buffer handling
Do not mess with the original skb, but allocate an independent bouncebuffer.
This protects against bad interference with mac80211's assumptions about
the skb (which already caused bugs).
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
David S. Miller [Wed, 11 Nov 2009 19:38:16 +0000 (11:38 -0800)]
Merge branch 'master' of /linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/wireless/iwlwifi/iwl-1000.c
drivers/net/wireless/iwlwifi/iwl-6000.c
drivers/net/wireless/iwlwifi/iwl-core.h
stephen hemminger [Tue, 10 Nov 2009 07:54:56 +0000 (07:54 +0000)]
CAN: use dev_get_by_index_rcu
Use new function to avoid doing read_lock().
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Tue, 10 Nov 2009 07:54:55 +0000 (07:54 +0000)]
IPV4: use rcu to walk list of devices in IGMP
This also needs to be optimized for large number of devices.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Tue, 10 Nov 2009 07:54:53 +0000 (07:54 +0000)]
decnet: use RCU to find network devices
When showing device statistics use RCU rather than read_lock(&dev_base_lock)
Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Tue, 10 Nov 2009 07:54:52 +0000 (07:54 +0000)]
s390: use RCU to walk list of network devices
This is similar to other cases where for_each_netdev_rcu
can be used when gathering information.
By inspection, don't have platform or cross-build environment
to validate.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Tue, 10 Nov 2009 07:54:49 +0000 (07:54 +0000)]
net: use rcu for network scheduler API
Use RCU to walk list of network devices in qdisc dump.
This could be optimized for large number of devices.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Tue, 10 Nov 2009 07:54:48 +0000 (07:54 +0000)]
vlan: eliminate use of dev_base_lock
Do not need to use read_lock(&dev_base_lock), use RCU instead.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Tue, 10 Nov 2009 07:54:47 +0000 (07:54 +0000)]
netdev: add netdev_continue_rcu
This adds an RCU macro for continuing search, useful for some
network devices like vlan.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Brian Haley [Mon, 9 Nov 2009 12:05:53 +0000 (12:05 +0000)]
IPv6: use ipv6_addr_v4mapped()
Change udp6_portaddr_hash() to use ipv6_addr_v4mapped()
inline instead of ipv6_addr_type().
Signed-off-by: Brian Haley <brian.haley@hp.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 9 Nov 2009 18:07:28 +0000 (18:07 +0000)]
parisc: led: Use for_each_netdev_rcu()
Use for_each_netdev_rcu() and dont lock dev_base_lock anymore
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Mon, 9 Nov 2009 08:42:01 +0000 (08:42 +0000)]
sit: Clean up DF code by copying from IPIP
This patch rearranges the SIT DF bit handling using the new IPIP DF
code. The only externally visible effect should be the case where
PMTU is enabled and the MTU is exactly 1280 bytes. In this case the
previous code would send packets out with DF off while the new code
would set the DF bit. This is inline with RFC 4213.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Thanks,
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 9 Nov 2009 07:40:17 +0000 (07:40 +0000)]
ipv6: Allow inet6_dump_addr() to handle more than 64 addresses
Apparently, inet6_dump_addr() is not able to handle more than
64 ipv6 addresses per device. We must break from inner loops
in case skb is full, or else cursor is put at the end of list.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 9 Nov 2009 12:11:28 +0000 (12:11 +0000)]
ipv6: speedup inet6_dump_ifinfo()
When handling large number of netdevice, inet6_dump_ifinfo()
is very slow because it has O(N^2) complexity.
Instead of scanning one single list, we can use the 256 sub lists
of the dev_index hash table, and RCU lookups.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cyrill Gorcunov [Sun, 8 Nov 2009 05:51:19 +0000 (05:51 +0000)]
net: netlink_getname, packet_getname -- use DECLARE_SOCKADDR guard
Use guard DECLARE_SOCKADDR in a few more places which allow
us to catch if the structure copied back is too big.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 4 Nov 2009 15:29:52 +0000 (15:29 +0000)]
usbnet: Set link down initially for drivers that update link state
Some usbnet drivers update link state while others do not due to
hardware limitations. Add a flag to distinguish those that do, and
set the link down initially for their devices.
This is intended to fix this bug: http://bugs.debian.org/444043
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marin Mitov [Sun, 8 Nov 2009 05:59:27 +0000 (05:59 +0000)]
niu: Use DMA_BIT_MASK(44) instead of deprecated DMA_44BIT_MASK
Use DMA_BIT_MASK(44) instead of deprecated DMA_44BIT_MASK
Signed-off-by: Marin Mitov <mitov@issp.bas.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 9 Nov 2009 05:26:33 +0000 (05:26 +0000)]
udp: bind() optimisation
UDP bind() can be O(N^2) in some pathological cases.
Thanks to secondary hash tables, we can make it O(N)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Mon, 9 Nov 2009 06:09:37 +0000 (06:09 +0000)]
bnx2x: version 1.52.1-4
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Mon, 9 Nov 2009 06:09:35 +0000 (06:09 +0000)]
bnx2x: Change coalescing granularity to 4us
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Mon, 9 Nov 2009 06:09:28 +0000 (06:09 +0000)]
bnx2x: Remove misleading error print
Failing to allocate MSI-X vectors is not an error and should not be
printed as such
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Mon, 9 Nov 2009 06:09:22 +0000 (06:09 +0000)]
bnx2x: GSO implies CSUM offload
Making sure that whenever the FW/HW is configured for GSO, it is also
configured to CSUM offload
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rémi Denis-Courmont [Mon, 9 Nov 2009 04:06:40 +0000 (04:06 +0000)]
Phonet: allocate and copy for pipe TX without sock lock
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rémi Denis-Courmont [Mon, 9 Nov 2009 02:17:01 +0000 (02:17 +0000)]
Phonet: put sockets in a hash table
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 11 Nov 2009 04:30:37 +0000 (20:30 -0800)]
speedfax: declare MODULE_FIRMWARE
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Sat, 7 Nov 2009 12:04:09 +0000 (12:04 +0000)]
pcnet-cs: declare MODULE_FIRMWARE
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Sat, 7 Nov 2009 11:55:20 +0000 (11:55 +0000)]
tms380tr: declare MODULE_FIRMWARE
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Sat, 7 Nov 2009 11:55:07 +0000 (11:55 +0000)]
spider-net: declare MODULE_FIRMWARE
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Sat, 7 Nov 2009 11:54:44 +0000 (11:54 +0000)]
myri10ge: declare MODULE_FIRMWARE
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Sat, 7 Nov 2009 11:53:52 +0000 (11:53 +0000)]
cxgb3: declare MODULE_FIRMWARE
Replace run-time string formatting with preprocessor string
manipulation.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Sat, 7 Nov 2009 11:53:39 +0000 (11:53 +0000)]
bnx2x: declare MODULE_FIRMWARE
Replace run-time string formatting with preprocessor string
manipulation.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Sat, 7 Nov 2009 11:46:07 +0000 (11:46 +0000)]
ambassador: declare MODULE_FIRMWARE
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Sat, 7 Nov 2009 11:40:32 +0000 (11:40 +0000)]
solos-pci: declare MODULE_FIRMWARE
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Sat, 7 Nov 2009 11:37:36 +0000 (11:37 +0000)]
netx: declare MODULE_FIRMWARE
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wey-Yi Guy [Fri, 6 Nov 2009 23:17:05 +0000 (15:17 -0800)]
iwlwifi: Fix issue on file transfer stalled in HT mode
Turn on RTS/CTS for HT to prevent uCode TX fifo underrun
This is fix for
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2103
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Tested-by: Jiajia Zheng <jiajia.zheng@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 6 Nov 2009 23:17:04 +0000 (15:17 -0800)]
iwlwifi: Use RTS/CTS as the preferred protection mechanism for 6000 series
When 802.11g was introduced, we had RTS/CTS and CTS-to-Self protection
mechanisms. In an HT Beacon, HT stations use the "Operating Mode" field
in the HT Information Element to determine whether or not to use
protection.
The Operating Mode field has 4 possible settings: 0-3:
Mode 0: If all stations in the BSS are 20/40 MHz HT capable, or if the
BSS is 20/40 MHz capable, or if all stations in the BSS are 20 MHz HT
stations in a 20 MHz BSS
Mode 1: used if there are non-HT stations or APs using the primary or
secondary channels
Mode 2: if only HT stations are associated in the BSS and at least one
20 MHz HT station is associated.
Mode 3: used if one or more non-HT stations are associated in the BSS.
When in operating modes 1 or 3, and the Use_Protection field is 1 in the
Beacon's ERP IE, all HT transmissions must be protected using RTS/CTS or
CTS-to-Self.
By default, CTS-to-self is the preferred protection mechanism for less
overhead and higher throughput; but using the full RTS/CTS will better
protect the inner exchange from interference, especially in
highly-congested environment.
For 6000 series WIFI NIC, RTS/CTS protection mechanism is the
recommended choice for HT traffic based on the HW design.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bing Zhao [Tue, 10 Nov 2009 02:04:13 +0000 (18:04 -0800)]
Libertas: fix issues while configuring host sleep using ethtool wol
Configuration of wake-on-lan for unicast, multicast, broadcast, physical
activity was not working. Kernel panic issue was there when user tries to
disable WOL. Fixed them.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bing Zhao [Tue, 10 Nov 2009 02:04:12 +0000 (18:04 -0800)]
Libertas: coding style cleanup in ethtool.c
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Mon, 9 Nov 2009 22:56:06 +0000 (16:56 -0600)]
rtl8187: Fix sparse warnings
Due to a missing header include, sparse generates the following warnings:
CHECK drivers/net/wireless/rtl818x/rtl8187_rfkill.c
warning: symbol 'rtl8187_rfkill_init' was not declared. Should it be static?
warning: symbol 'rtl8187_rfkill_poll' was not declared. Should it be static?
warning: symbol 'rtl8187_rfkill_exit' was not declared. Should it be static?
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bob Copeland [Mon, 9 Nov 2009 02:59:02 +0000 (21:59 -0500)]
ath5k: add LED definition for BenQ Joybook R55v
Setup the GPIOs for the BenQ Joybook netbook.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bob Copeland [Mon, 9 Nov 2009 02:59:01 +0000 (21:59 -0500)]
ath5k: add LED support for HP Compaq CQ60
Add GPIO configuration for the Compaq CQ60 laptop
Reported-by: David Dreggors <ddreggors@jumptv.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bob Copeland [Mon, 9 Nov 2009 02:59:00 +0000 (21:59 -0500)]
ath5k: don't reset mcast filter when configuring the mode
We should not zero out the multicast hash when configuring
the operating mode, since a zero value means all multicast
frames will get dropped. Also, ath5k_mode_setup() gets
called after any reset, so the hash already set up in
configure_filter() is lost.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sat, 7 Nov 2009 18:14:47 +0000 (19:14 +0100)]
rt2x00: update MAINTAINERS
Although I have always been the active maintainer of the rt2x00 drivers,
I was not mentioned explicitely in the MAINTAINERS file as such.
Update the rt2x00 entry in the MAINTAINERS file to add my name and
email address.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 7 Nov 2009 17:37:37 +0000 (18:37 +0100)]
b43: work around a locking issue in ->set_tim()
ops->set_tim() must be atomic, so b43 trying to acquire a mutex leads
to a kernel crash. This patch trades an easy to trigger crash in AP
mode for an unlikely race condition. According to Michael, the real
fix would be to allow set_tim() to sleep, since b43 is not the only
driver that needs to sleep in all callbacks.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Martin Fuzzey [Fri, 6 Nov 2009 20:21:27 +0000 (21:21 +0100)]
ssb-pcmcia: Fix 32bit register access in early bus scanning
The scan function was using 32 bit access which does not
work on 16bit CF cards.
This patch corrects this by doing two 16 bit reads like
ssb_pcmcia_read32 already does.
mb -- Removed locking. That early in init there's no need for locking.
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
David S. Miller [Mon, 9 Nov 2009 19:17:24 +0000 (11:17 -0800)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-next-2.6
David S. Miller [Mon, 9 Nov 2009 07:00:54 +0000 (23:00 -0800)]
Merge branch 'master' of /linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/can/usb/ems_usb.c
Yury Polyanskiy [Mon, 9 Nov 2009 04:58:41 +0000 (20:58 -0800)]
xfrm: SAD entries do not expire correctly after suspend-resume
This fixes the following bug in the current implementation of
net/xfrm: SAD entries timeouts do not count the time spent by the machine
in the suspended state. This leads to the connectivity problems because
after resuming local machine thinks that the SAD entry is still valid, while
it has already been expired on the remote server.
The cause of this is very simple: the timeouts in the net/xfrm are bound to
the old mod_timer() timers. This patch reassigns them to the
CLOCK_REALTIME hrtimer.
I have been using this version of the patch for a few months on my
machines without any problems. Also run a few stress tests w/o any
issues.
This version of the patch uses tasklet_hrtimer by Peter Zijlstra
(commit 9ba5f0).
This patch is against 2.6.31.4. Please CC me.
Signed-off-by: Yury Polyanskiy <polyanskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Mon, 9 Nov 2009 04:57:03 +0000 (20:57 -0800)]
net/compat_ioctl: support SIOCWANDEV
This adds compat_ioctl support for SIOCWANDEV, which has
always been missing.
The definition of struct compat_ifreq was missing an
ifru_settings fields that is needed to support SIOCWANDEV,
so add that and clean up the whitespace damage in the
struct definition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Mon, 9 Nov 2009 04:56:21 +0000 (20:56 -0800)]
net, compat_ioctl: fix SIOCGMII ioctls
SIOCGMIIPHY and SIOCGMIIREG return data through ifreq,
so it needs to be converted on the way out as well.
SIOCGIFPFLAGS is unused, but has the same problem in theory.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 8 Nov 2009 10:20:19 +0000 (10:20 +0000)]
udp: multicast RX should increment SNMP/sk_drops counter in allocation failures
When skb_clone() fails, we should increment sk_drops and SNMP counters.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 8 Nov 2009 10:18:52 +0000 (10:18 +0000)]
ipv6: udp: Optimise multicast reception
IPV6 UDP multicast rx path is a bit complex and can hold a spinlock
for a long time.
Using a small (32 or 64 entries) stack of socket pointers can help
to perform expensive operations (skb_clone(), udp_queue_rcv_skb())
outside of the lock, in most cases.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 8 Nov 2009 10:18:44 +0000 (10:18 +0000)]
ipv4: udp: Optimise multicast reception
UDP multicast rx path is a bit complex and can hold a spinlock
for a long time.
Using a small (32 or 64 entries) stack of socket pointers can help
to perform expensive operations (skb_clone(), udp_queue_rcv_skb())
outside of the lock, in most cases.
It's also a base for a future RCU conversion of multicast recption.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Lucian Adrian Grijincu <lgrijincu@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 8 Nov 2009 10:18:30 +0000 (10:18 +0000)]
ipv6: udp: optimize unicast RX path
We first locate the (local port) hash chain head
If few sockets are in this chain, we proceed with previous lookup algo.
If too many sockets are listed, we take a look at the secondary
(port, address) hash chain.
We choose the shortest chain and proceed with a RCU lookup on the elected chain.
But, if we chose (port, address) chain, and fail to find a socket on given address,
we must try another lookup on (port, in6addr_any) chain to find sockets not bound
to a particular IP.
-> No extra cost for typical setups, where the first lookup will probabbly
be performed.
RCU lookups everywhere, we dont acquire spinlock.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 8 Nov 2009 10:18:11 +0000 (10:18 +0000)]
ipv4: udp: optimize unicast RX path
We first locate the (local port) hash chain head
If few sockets are in this chain, we proceed with previous lookup algo.
If too many sockets are listed, we take a look at the secondary
(port, address) hash chain we added in previous patch.
We choose the shortest chain and proceed with a RCU lookup on the elected chain.
But, if we chose (port, address) chain, and fail to find a socket on given address,
we must try another lookup on (port, INADDR_ANY) chain to find socket not bound
to a particular IP.
-> No extra cost for typical setups, where the first lookup will probabbly
be performed.
RCU lookups everywhere, we dont acquire spinlock.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 8 Nov 2009 10:17:58 +0000 (10:17 +0000)]
udp: secondary hash on (local port, local address)
Extends udp_table to contain a secondary hash table.
socket anchor for this second hash is free, because UDP
doesnt use skc_bind_node : We define an union to hold
both skc_bind_node & a new hlist_nulls_node udp_portaddr_node
udp_lib_get_port() inserts sockets into second hash chain
(additional cost of one atomic op)
udp_lib_unhash() deletes socket from second hash chain
(additional cost of one atomic op)
Note : No spinlock lockdep annotation is needed, because
lock for the secondary hash chain is always get after
lock for primary hash chain.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 8 Nov 2009 10:17:30 +0000 (10:17 +0000)]
udp: split sk_hash into two u16 hashes
Union sk_hash with two u16 hashes for udp (no extra memory taken)
One 16 bits hash on (local port) value (the previous udp 'hash')
One 16 bits hash on (local address, local port) values, initialized
but not yet used. This second hash is using jenkin hash for better
distribution.
Because the 'port' is xored later, a partial hash is performed
on local address + net_hash_mix(net)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 8 Nov 2009 10:17:05 +0000 (10:17 +0000)]
udp: add a counter into udp_hslot
Adds a counter in udp_hslot to keep an accurate count
of sockets present in chain.
This will permit to upcoming UDP lookup algo to chose
the shortest chain when secondary hash is added.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Rothwell [Mon, 9 Nov 2009 04:41:03 +0000 (20:41 -0800)]
net/appletalk: using compat_ptr needs inclusion of linux/compat.h
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christian Pellegrin [Mon, 2 Nov 2009 23:07:00 +0000 (23:07 +0000)]
can: Driver for the Microchip MCP251x SPI CAN controllers
Signed-off-by: Christian Pellegrin <chripell@fsfe.org>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / kernel / kernel-generic.git / log