Eliad Peller [Thu, 25 Aug 2011 15:11:00 +0000 (18:11 +0300)]
wl12xx: add beacon_filtering debugfs file
Allow enabling/disabling beacon_filtering by debugfs,
in order to reduce the log size while debugging (beacon
filtering is disabled by default in AP mode, as beacons
are needed for ERP configuration).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Thu, 25 Aug 2011 15:10:59 +0000 (18:10 +0300)]
wl12xx: add module_param to trigger BUG() on recovery
Crashing on recovery is useful for debugging, as a JTAG
can be connected in order to investigate the current fw state.
(otherwise, a reconfiguration will occur)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Thu, 25 Aug 2011 15:10:58 +0000 (18:10 +0300)]
wl12xx: print the seq_num of rx packet
Make it easier to match the driver log against
a sniffer log.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Thu, 25 Aug 2011 15:10:57 +0000 (18:10 +0300)]
wl12xx: print acx id
Add id param to the acx debug print (on wl1271_cmd_configure)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Luciano Coelho [Wed, 14 Sep 2011 08:32:15 +0000 (11:32 +0300)]
Merge branch 'wl12xx-next' into for-linville
Pavel Roskin [Thu, 1 Sep 2011 15:54:12 +0000 (11:54 -0400)]
cfg80211: print bandwidth in chan_reg_rule_print_dbg()
Two spaces and the second "KHz" suggest that the code author meant to
print the bandwidth but forgot it. The code appears in commit
e702d3cf
already with two spaces and "KHz" in place of the bandwidth.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bill Jordan [Wed, 31 Aug 2011 21:51:00 +0000 (17:51 -0400)]
ath9k: ath9k_hw_set_txpowerlimit sets previous txpower
In commit
9c204b46c7af93e334114bea1f5eeaa6fea9ba07
(ath9k_hw: do not limit initial tx power to 20 dbm),
setting of txpower was broken.
This patch fixes it by initializing reg_pwr from the new
power limit, not the previous value.
Signed-off-by: Bill Jordan <bjordan@rajant.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Wed, 31 Aug 2011 21:36:21 +0000 (23:36 +0200)]
b43: LCN-PHY: add conditions for few operations
It was not possible to guess the conditions from MMIO dumps. Take them
from brcmsmac code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Wed, 31 Aug 2011 21:36:20 +0000 (23:36 +0200)]
b43: LCN-PHY: rename functions, get rid of magic names
We've compared b43 with brcmsmac and took functions names from the
later.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Wed, 31 Aug 2011 21:36:19 +0000 (23:36 +0200)]
b43: LCN-PHY: upload additional 0x7 table
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Wed, 31 Aug 2011 21:36:18 +0000 (23:36 +0200)]
b43: LCN-PHY: rewrite 0x7 table at the end of init
This is not implemented in brcmsmac, but was noticed in (newer) wl. Can
be workaround for some hardware bug.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Wed, 31 Aug 2011 21:36:17 +0000 (23:36 +0200)]
b43: LCN-PHY: put tables functions in correct file
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Wed, 31 Aug 2011 21:36:16 +0000 (23:36 +0200)]
b43: LCN-PHY: minor fixes
The biggest change is reversing order of reading 32-bit table value.
MMIO dumps has shown it's done that way for LCN-PHY.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zero.lin [Wed, 31 Aug 2011 18:43:52 +0000 (20:43 +0200)]
rt2x00: Add new chipset support
Signed-off-by: zero.lin <zero.lin@ralinktech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Wed, 31 Aug 2011 13:01:48 +0000 (16:01 +0300)]
nl80211/cfg80211: add match filtering for sched_scan
Introduce filtering for scheduled scans to reduce the number of
unnecessary results (which cause useless wake-ups).
Add a new nested attribute where sets of parameters to be matched can
be passed when starting a scheduled scan. Only scan results that
match any of the sets will be returned.
At this point, the set consists of a single parameter, an SSID. This
can be easily extended in the future to support more complex matches.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eliad Peller [Wed, 31 Aug 2011 08:29:43 +0000 (11:29 +0300)]
nl80211/cfg80211: add WIPHY_FLAG_AP_UAPSD flag
add WIPHY_FLAG_AP_UAPSD flag to indicate uapsd support on
AP mode.
Advertise it to userspace by including a new
NL80211_ATTR_SUPPORT_AP_UAPSD attribute.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Wed, 31 Aug 2011 06:38:30 +0000 (09:38 +0300)]
iwlwifi: signedness bug in iwl_trans_pcie_tx_agg_alloc()
unsigned shorts and unsigned chars are never == -1.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Wed, 31 Aug 2011 06:37:42 +0000 (09:37 +0300)]
iwlwifi: fix double assign in iwl_start_tx_ba_trans_ready()
"vif" is assigned twice. We can remove the first one.
This silences a Smatch warning that "ctx" could be one step past the
end of the priv->contexts[] array.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Wed, 31 Aug 2011 05:17:30 +0000 (10:47 +0530)]
ath9k_hw: Fix rx latency of 11a mode
Rx latecy to start signal(usec) of 11a is 41 not 37 and
also corrected the rx delay in quarter rate.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Tue, 30 Aug 2011 19:16:15 +0000 (22:16 +0300)]
mac80211: handle allocation failures in mesh_pathtbl_init()
The calls to kzalloc() weren't checked here and it upsets the static
checkers. Obviously they're not super likely to fail, but we might
as well add some error handling.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arik Nemtsov [Tue, 30 Aug 2011 06:32:38 +0000 (09:32 +0300)]
mac80211: add flag to indicate HW only Tx-agg setup support
When this flag is set, Tx A-MPDU sessions will not be started by
mac80211. This flag is required for devices that support Tx A-MPDU setup
in hardware.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Mon, 29 Aug 2011 21:17:41 +0000 (14:17 -0700)]
wireless: Remove unnecessary OOM logging messages
Removing unnecessary messages saves code and text.
Site specific OOM messages are duplications of a generic MM
out of memory message and aren't really useful, so just
delete them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Mon, 29 Aug 2011 21:17:34 +0000 (14:17 -0700)]
rfkill: Remove unnecessary OOM logging messages
Removing unnecessary messages saves code and text.
Site specific OOM messages are duplications of a generic MM
out of memory message and aren't really useful, so just
delete them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Mon, 29 Aug 2011 21:17:31 +0000 (14:17 -0700)]
mac80211: Remove unnecessary OOM logging messages
Removing unnecessary messages saves code and text.
Site specific OOM messages are duplications of a generic MM
out of memory message and aren't really useful, so just
delete them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Javier Cardona [Mon, 29 Aug 2011 20:23:09 +0000 (13:23 -0700)]
mac80211: Consolidate mesh path duplicated functions
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Javier Cardona [Mon, 29 Aug 2011 20:23:08 +0000 (13:23 -0700)]
mac80211: Consolidate {mesh,mpp}_path_flush into one function
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Javier Cardona [Mon, 29 Aug 2011 20:23:07 +0000 (13:23 -0700)]
mac80211: Don't iterate twice over all mpaths when once in sufficient
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Javier Cardona [Mon, 29 Aug 2011 20:23:06 +0000 (13:23 -0700)]
mac80211: Remove redundant mesh path expiration checks
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Javier Cardona [Mon, 29 Aug 2011 20:23:05 +0000 (13:23 -0700)]
mac80211: Improve mpath state locking
No need to take the mpath state lock when an mpath is removed.
Also, no need checking the lock when reading mpath flags.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Javier Cardona [Mon, 29 Aug 2011 20:23:04 +0000 (13:23 -0700)]
mac80211: Remove mesh paths when an interface is removed
When an interface is removed, the mesh paths associated with it should
also be removed.
This fixes a bug we observed when reloading a device driver module
without reloading mac80211s.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Javier Cardona [Mon, 29 Aug 2011 20:23:03 +0000 (13:23 -0700)]
mac80211: Fix RCU pointer dereference in mesh_path_discard_frame()
Reported by Pedro Larbig (ASPj)
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yogesh Ashok Powar [Mon, 29 Aug 2011 20:21:10 +0000 (13:21 -0700)]
mwifiex: replace kmalloc & memcpy sequence with kmemdup
Sequence of kmalloc/kzalloc and memcpy is replaced with
kmemdup.
Cc: Walter Harms <wharms@bfs.de>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 29 Aug 2011 16:57:54 +0000 (18:57 +0200)]
ath9k: fix checks for first subframe delimiter padding
The commit "ath9k_hw: Fix exceed transmission burst-time of 5GHz" added
a padding of 60 delimiters on the first subframe to work around an issue
on AR9380, but it lacked the checks to prevent it from being applied to
pre-AR9380, enterprise AR9380 or AR9580+
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yogesh Ashok Powar [Mon, 29 Aug 2011 11:42:44 +0000 (17:12 +0530)]
mwl8k: Set hardware flag IEEE80211_HW_AP_LINK_PS
This will avoid mac80211 to trigger PS mode for connected station
based on the PM bit of incoming frames. AP firmware is capable of
handling such frames and buffering TX frames destined to the
stations that are in PS mode.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 29 Aug 2011 11:39:47 +0000 (13:39 +0200)]
ath9k_hw: fix the last register write for ar5416 addac
The previous register used in these initvals was probably accidentally
copied over from the AR9100 values.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 29 Aug 2011 11:39:46 +0000 (13:39 +0200)]
ath9k_hw: drop an unused column in AR5008-AR9002 initvals
It was used for the defunct 'turbo' mode which was never implemented in the
driver. Saves ~7.5k uncompressed
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vivek Natarajan [Mon, 29 Aug 2011 08:53:03 +0000 (14:23 +0530)]
cfg80211/nl80211: Indicate roaming feature capability to userspace.
When the rssi of the current AP drops, both wpa_supplicant and the
firmware may do a background scan to find a better AP and try to
associate. Since firmware based roaming is faster, inform
wpa_supplicant to avoid roaming and let the firmware decide to
roam if necessary.
For fullmac drivers like ath6kl, it is just enough to provide the
ESSID and the firmware will decide on the BSSID. Since it is not
possible to do pre-auth during roaming for fullmac drivers, the
wpa_supplicant needs to completely disconnect with the old AP and
reconnect with the new AP. This consumes lot of time and it is
better to leave the roaming decision to the firmware.
Signed-off-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sun, 28 Aug 2011 19:11:01 +0000 (21:11 +0200)]
mac80211: retry sending failed BAR frames later instead of tearing down aggr
Unfortunately failed BAR tx attempts happen more frequently than I
expected, and the resulting aggregation teardowns cause performance
issues, as the aggregation session does not always get re-established
properly.
Instead of tearing down the entire aggr session, we can simply store the
SSN of the last failed BAR tx attempt, wait for the first successful
tx status event, and then send another BAR with the same SSN.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Sun, 28 Aug 2011 17:59:28 +0000 (19:59 +0200)]
b43: LCN-PHY: implement saving and restoring PHY & radio configuration
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Sun, 28 Aug 2011 16:47:23 +0000 (18:47 +0200)]
bcma: extract some basic info about board from SPROM
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Sun, 28 Aug 2011 16:47:22 +0000 (18:47 +0200)]
ssb: use u16 for storing board rev
Specs say about size 2 (u16) and my 14e4:4727 has board rev 0x1211.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Sun, 28 Aug 2011 12:59:58 +0000 (14:59 +0200)]
b43: LCN-PHY: prepare functions for channel switching
Switching is not fully implemented yet, prepare place for the code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Sun, 28 Aug 2011 12:28:44 +0000 (14:28 +0200)]
b43: LCN-PHY: implement more PHY ops before radio init
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Sun, 28 Aug 2011 12:28:43 +0000 (14:28 +0200)]
b43: LCN-PHY: add R/W ops for PHY and radio
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 27 Aug 2011 23:52:10 +0000 (01:52 +0200)]
ath9k_hw: do not apply the 2.4 ghz ack timeout workaround to cts
It is only used to workaround interoperability issues related to longer
delays in receiving the block ack, so it is not necessary to apply it
to the CTS exchange.
Should improve throughput slightly, especially when there are lots
of retransmissions.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Javier Cardona [Tue, 6 Sep 2011 19:10:43 +0000 (12:10 -0700)]
mac80211: Defer tranmission of mesh path errors
Under failure conditions, the mesh stack sends PERR messages to the
previous sender of the failed frame. This happens in the tx feedback
path, in which the transmission queue lock may be taken. Avoid a
deadlock by sending the path error via the pending queue.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Greg Dietsche [Sun, 28 Aug 2011 13:22:38 +0000 (08:22 -0500)]
iwlwifi: iwl-agn-rs.c: remove old comment
this comment refers to some code that was removed.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 27 Aug 2011 22:32:25 +0000 (00:32 +0200)]
ath9k: defer ath_tx_setup_buffer setup to the first tx attempt during aggr
With sequence number and buffer allocation deferred to when they're needed
for the first time, it becomes much easier to start dropping packets from
the tid queue if necessary, e.g. when latency suddenly increases. This can
lead to some future improvements in buffer management for better latency.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 27 Aug 2011 22:32:24 +0000 (00:32 +0200)]
ath9k: move seqno allocation in the tx path to ath_tx_setup_buffer
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 27 Aug 2011 22:32:23 +0000 (00:32 +0200)]
ath9k: move the sequence number from ath_frame_info to ath_buf
It is only necessary for BAW tracking and moving it to the ath_buf
makes it easier to add further improvements, such as deferring
seqno allocation in the aggregation path.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 27 Aug 2011 22:32:22 +0000 (00:32 +0200)]
ath9k: clean up the aggregation tid queue
Use a sk_buff_head instead containing skbs instead of a list_head
containing ath_bufs. This makes it easier to decouple the aggregation
code from the ath_buf struct
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 27 Aug 2011 22:32:21 +0000 (00:32 +0200)]
ath9k: use u8 for the tx key index
This saves some space in struct ath_frame_info
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Fri, 26 Aug 2011 08:56:39 +0000 (01:56 -0700)]
ath: Make ath_printk void not int and remove unused struct ath_common *
Changing the return type and removing the unused argument from
ath_printk reduces code size.
Add an __always_unused struct ath_common * to the macros
that call ath_printk to avoid unused variable warnings.
$ size drivers/net/wireless/ath/built-in.o*
text data bss dec hex filename
1159859 16235 212000 1388094 152e3e drivers/net/wireless/ath/built-in.o.new
1164175 16235 212032 1392442 153f3a drivers/net/wireless/ath/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Fri, 26 Aug 2011 08:56:38 +0000 (01:56 -0700)]
ath: Make ath_dbg void not int
The return value is never used so make it void.
Reduces object size a tiny bit.
$ size drivers/net/wireless/ath/built-in.o*
text data bss dec hex filename
1164175 16235 212032 1392442 153f3a drivers/net/wireless/ath/built-in.o.new
1164819 16235 212032 1393086 1541be drivers/net/wireless/ath/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Mon, 29 Aug 2011 19:47:58 +0000 (15:47 -0400)]
wl12xx/sdio_test.c: fix build breakage from WL127X_FW_NAME change
Commit
c302b2c959164622558474871ae942da0e484a38 ("wl12xx: Use a single
fw for both STA and AP roles") changed the name of the firmware name
definition, breaking the build of wl12xx/sdio_test.c.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Sat, 27 Aug 2011 20:53:42 +0000 (15:53 -0500)]
b43: Fix swatch warning
Swatch reports the following warning for main.c:
CHECK drivers/net/wireless/b43/main.c
drivers/net/wireless/b43/main.c +4115 b43_wireless_core_stop(7) warn: variable dereferenced before check 'dev'
After analysis, this is not a bug, but a false warning. Nonetheless,
a cleanup is in order to prevent some future janitor proposing
the wrong fix, as I did in my original patch.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Sat, 27 Aug 2011 18:56:00 +0000 (13:56 -0500)]
ath9k: Fix a smatch warnings
Smatch shows the following warnings:
CHECK drivers/net/wireless/ath/ath9k/htc_drv_main.c
drivers/net/wireless/ath/ath9k/htc_drv_main.c +1315 ath9k_htc_configure_filter(27) warn: inconsistent returns mutex:&priv->mutex: locked (1303) unlocked (1315)
CHECK drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
drivers/net/wireless/ath/ath9k/ar9003_eeprom.c +3321 ar9300_eeprom_restore_internal(20) warn: returning -1 instead of -ENOMEM is sloppy
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Sat, 27 Aug 2011 10:47:47 +0000 (16:17 +0530)]
ath9k: Add debugfs support for mac/baseband samples
This patch keep track of number of samples that includes
DMA debugs registers, PCU observe, CR, channel noise,
cycle conters, noisefloor history buffer and last N number
of tx and rx descriptor status. These samples are grouped
in table manner which dumping in debgufs.
Debugfs file location:
<debugfs_mnt>/ieee80211/phy#/ath9k/samples
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 27 Aug 2011 08:25:27 +0000 (10:25 +0200)]
ath9k: fix regression in sending aggregated packets
The recent commit "ath9k: Send legacy rated frames as unaggregated"
introduced a check to ensure that packets with non-MCS rates set in
the rate series will not be aggregated. However, it failed to check
if the rate series is valid before testing the flags, thus breaking
aggregation for normal MCS-only packets if the last series is unset.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Sat, 27 Aug 2011 06:43:21 +0000 (12:13 +0530)]
ath9k: Fix eifs/usec timeout for AR9287 v1.3+
For AR9287 v1.3+ chips, MAC runs at 117MHz. But the initvals
IFS parameters are loaded based on 44/88MHz clockrate. So
eifs/usec from ini should not be used for AR9287 v1.3+.
The mentioned values are tested on 2 chain HT40 mode.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Sat, 27 Aug 2011 05:52:59 +0000 (11:22 +0530)]
ath9k_hw: Set default slottime as 9us
Initialize 9us slot time as that is what is used mostly
(for non-ERP cases) and also to be in sync with initvals.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Fri, 26 Aug 2011 18:41:40 +0000 (20:41 +0200)]
b43: make HT-PHY support experimental
It was tested on three BCM4331 devices, code has been written from MMIO
dumps only, but seems to be quite stable.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Fri, 26 Aug 2011 18:41:39 +0000 (20:41 +0200)]
b43: use 8K buffers for 64-bit DMA to workaround hardware bug
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Fri, 26 Aug 2011 18:41:38 +0000 (20:41 +0200)]
b43: Relax requirement for descriptors to be in the DMA zone
When 64-bit DMA was first used, there were problems with the
BCM4311 (14e4:4311). The problem was "fixed" by using the GFP_DMA
flag in the allocation of coherent ring descriptor memory.
The original problem is now believed to have been due to bugs in
the 64-bit DMA implementation in the rest of the kernel, and that
those bugs have been fixed. Accordingly, the requirement for the
descriptors to be in the DMA zone is relaxed.
Bounce buffers are left in the DMA zone.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Michael Buesch <m@bues.ch>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Axel Lin [Fri, 26 Aug 2011 06:34:59 +0000 (14:34 +0800)]
p54spi: add "spi:" prefix for stlc45xx modalias
Since commit
e0626e38 (spi: prefix modalias with "spi:"),
the spi modalias is prefixed with "spi:".
This patch adds "spi:" prefix for modalias of stlc45xx.
Also move it to be group with other modalias.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-By: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 26 Aug 2011 06:13:56 +0000 (23:13 -0700)]
iwlagn: handle GO powersave
In order to implement support for GO powersave on
the P2P client side, the ucode needs to know what
GO we're trying to authenticate/associate with,
it needs to have a station entry and the BSSID in
the RXON set.
Implement the new mac80211 callbacks to give this
data to the device.
Since this is also useful for the device when a
normal connection is established, also program it
with the information in that case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:32 +0000 (23:11 -0700)]
iwlagn: move tx queues to transport layer
This finalizes the move of the data path to the transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:31 +0000 (23:11 -0700)]
iwlagn: move the stop / wake queue logic to transport layer
priv->mac80211_registered and priv->hw needed to move to shared.
stop_queue API was added in order to allow the upper layer to stop
the SW queues for regulatory purposes.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:30 +0000 (23:11 -0700)]
iwlagn: move check_stuck_queue to transport layer
This one is really transport related.
==== moves Stanislaw's code to BSD area ====
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:29 +0000 (23:11 -0700)]
iwlagn: move wait_for_tx_queue_empty to transport layer
This one is really transport related.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:28 +0000 (23:11 -0700)]
iwlagn: cosmetics in iwl-trans.h
Remove a few dereferences of priv from the transport layer while
at it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:27 +0000 (23:11 -0700)]
iwlagn: move the disable agg logic to transport layer
Since all the check_empty logic is now in the transport layer,
the upper layer doesn't need to know anything about tx queues.
The disable aggregation flow was the last to know what a tx queue
is, so move it too.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:26 +0000 (23:11 -0700)]
iwlagn: move the check_empty logic to the transport layer
This logic is responsible to tell mac80211 when the HW queues are
empty and the BA session can be started / torn down.
Fix a bug on the way:
When the the Tx BA session is stopped and the HW queues aren't empty,
we stop the SW queue to drain the HW queue and then switch to the
legacy HW queue. This is the IWL_EMPTYING_HW_QUEUE_DELBA state.
While in this state, we never wake the SW queue, even when the HW
queue is almost empty, since we need to drain it completely. Look
at iwl_trans_pcie_reclaim regarding this.
Once the HW queue is really empty, we must wake the SW queue in order
to get traffic to the legacy queue.
This step was missing leading to an odd situation were the traffic
would just stall after we tore down a Tx BA session while the HW
queue was not empty.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:25 +0000 (23:11 -0700)]
iwlagn: allocate resources for TX BA session in transport
The queues and all the related logic suits to the transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:24 +0000 (23:11 -0700)]
iwlagn: move the mapping ac to queue / fifo to transport
This mapping is transport related.
This allows us to remove the notion of tx queue from the tx path in
the upper layer.
iwl_wake_any_queue moved to transport layer since it needs to access
these mappings.
The TX API is nicer now:
int (*tx)(struct iwl_trans *trans, struct sk_buff *skb,
struct iwl_device_cmd *dev_cmd, u8 ctx, u8 sta_id);
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:23 +0000 (23:11 -0700)]
iwlagn: upper layer uses slabs to allocate tx cmds
In a near future, the upper layer won't be aware of the tx queues.
This allows to remove one place where the upper layer needed to
provide the tx queue index to the transport layer.
This also saves around 1.5MB.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:22 +0000 (23:11 -0700)]
iwlagn: set tx_fifo for ampdu in transport layer
the mapping tx_queue -> fifo is really transport related. The upper
layer should be involved in such things.
Note that upon agg_disable, the queue is always mapped to fifo 0, but
this doesn't matter since when the queue will be setup again for a
new BA session, it will be configured to the good fifo anyway.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:21 +0000 (23:11 -0700)]
iwlagn: upper layer stores iwl_rxon_context in skb's CB
This removes the need for iwl_tx_info.
Each tx queue holds an array of skbs, the transport layer doesn't
need to know anything about the context in which a specific skb is
sent.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:20 +0000 (23:11 -0700)]
iwlagn: stop the device before freeing it
When we remove the module, we free all the tx and rx resources.
Before doing that, we'd better stop the tx / rx activity. Calling
iwl_trans_stop_device in iwl_remove helps also to remove a few API
functions:
* rx_free: happens in iwl_trans_free
* tx_free: happens in iwl_trans_free
* disable_sync_irq: happens in iwl_trans_stop_device
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:19 +0000 (23:11 -0700)]
iwlagn: remove dereferences of priv from transport
There are still quite a few, but much less.
A few fields have been moved /copied to hw_params which sits in the
shared area:
* priv->cfg->base_params->num_of_ampdu_queues
* priv->cfg->base_params->shadow_reg_enable
* priv->cfg->sku
* priv->ucode_owner
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:18 +0000 (23:11 -0700)]
iwlagn: iwl_tid_data moves to iwl-shared
The rate scaling and the transport need to access the data in
iwl_tid_data, hence the move.
Note that the only component in the upper layer that needs this data
is the rate scaling. Refactoring the rate scaling may help to move
iwl_tid_data from the shared area to the transport area.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 26 Aug 2011 06:11:17 +0000 (23:11 -0700)]
iwlagn: adding special "D" SKU for 2000 series
One more sku for 2000 series with different Subsystem ID
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:16 +0000 (23:11 -0700)]
iwlagn: iwl-pci doesn't include iwl-dev any more
Move all the iwlXXX_abgn_cfg forward declaration to a separate file
so that iwl-pci.c doesn't need to include iwl-agn.h that includes
all iwl-dev.h
This allows to provide real encapsulation. Dereferencing iwl_priv
in the bus layer will now lead to a compilation error.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Halperin [Fri, 26 Aug 2011 06:11:15 +0000 (23:11 -0700)]
iwlagn: fix compile warnings when CONFIG_PM_SLEEP is not set
CC [M] drivers/net/wireless/iwlwifi/iwl-pci.o
drivers/net/wireless/iwlwifi/iwl-pci.c:506: warning: \91iwl_pci_suspend\92 defined but not used
drivers/net/wireless/iwlwifi/iwl-pci.c:519: warning: \91iwl_pci_resume\92 defined but not used
These are only used if CONFIG_PM_SLEEP is enabled. CONFIG_PM depends
(CONFIG_PM_SLEEP || CONFIG_PM_RUNTIME), so it can be set without
CONFIG_PM_SLEEP selected.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:14 +0000 (23:11 -0700)]
iwlagn: all function iwl-io.c receive iwl_bus
Which means that iwl-io.c doesn't need to include iwl-dev.h any more.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:13 +0000 (23:11 -0700)]
iwlagn: add missing includes
a few h files weren't self contained. Fix that.
Move iwl_dma_ptr to transport layer since it is not used by the upper layer
any more.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:12 +0000 (23:11 -0700)]
iwlagn: move Keep Warm to transport layer
It is relevant for PCIe only.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:11 +0000 (23:11 -0700)]
iwlagn: iwl-dev.h doesn't include iwl-fh.h any more
Since iwl-fh.h contains transport related data, it shouldn't be included by the
upper layer.
Only the transport layer and iwl-agn-ucode.c includes it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:10 +0000 (23:11 -0700)]
iwlagn: remove unused parameters from hw_params
Some of them weren't used at all, the others always had the same value since
the driver split.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:09 +0000 (23:11 -0700)]
iwlagn: remove references to priv from the transport layer
Continue to the clean up of the priv dereferencing from the transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:08 +0000 (23:11 -0700)]
iwlagn: move dump_csr and dump_fh to transport layer
These are transport layer related. Move also the corresponding debugfs handlers.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:07 +0000 (23:11 -0700)]
iwlagn: move hcmd_lock to transport layer
Since it is needed for host commands only, it is needed in transport layer only
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:06 +0000 (23:11 -0700)]
iwlagn: transport layer should receive iwl_trans
Change a lot of functions to have them receive iwl_trans and not iwl_priv.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:05 +0000 (23:11 -0700)]
iwlagn: move iwl_free_pages to iwl-shared.h
This helper is used by the transport and the upper layer.
Kill __iwl_free_pages which was used in the transport only.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:04 +0000 (23:11 -0700)]
iwlagn: move all iwl_is_XXX helpers to iwl-shared.h
Logic move after all priv->status moved to struct iwl_shared
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:03 +0000 (23:11 -0700)]
iwlagn: fix the check of IWLAGN_FIRST_AMPDU_QUEUE
BUILD_BUG_ON(ARRAY_SIZE(iwlagn_ipan_queue_to_tx_fifo) !=
IWLAGN_FIRST_AMPDU_QUEUE);
This check can be buggy. IWLAGN_FIRST_AMPDU_QUEUE has to be greater than the
ARRAY_SIZE of iwlagn_ipan_queue_to_tx_fifo.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:02 +0000 (23:11 -0700)]
iwlagn: move scd_bc_tbls and scd_base_addr to iwl_trans_pcie
Needed for PCIe only
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:01 +0000 (23:11 -0700)]
iwlagn: move reclaim related functions
Now that the reclaim flow has been moved to the transport layer, a lot of
functions can be made static or don't need to be exported outside the transport
layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:00 +0000 (23:11 -0700)]
iwlagn: reclaim the packets in transport layer
The reclaim flow is really transport related. Define a simple API to allow the
upper layer to request from the transport layer to reclaim packets until an
index written in the Tx response / BA notification.
The transport layer prepares a list of the packets that are being freed and
passes this list to the upper layer.
Between the two layers, the CB of the skb is used to pass a pointer to the
context (BSS / PAN) in which the skb was sent.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:10:59 +0000 (23:10 -0700)]
iwlagn: move isr_statistics to transport layer
It is accessed by the transport layer only, hence the move.
The debugfs handlers that accessed it moved to the transport layer too.
The rx_handlers part of it stayed in the upper layer and a special debugfs
has been added for it
Also add missing includes to iwl-commands.h.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>