Hayes Wang [Wed, 3 Feb 2021 09:14:28 +0000 (17:14 +0800)]
r8152: replace several functions about phy patch request
Replace r8153_patch_request() with rtl_phy_patch_request().
Replace r8153_pre_ram_code() with rtl_pre_ram_code().
Replace r8153_post_ram_code() with rtl_post_ram_code().
Add rtl_patch_key_set().
The new functions have an additional parameter. It is used to wait
the patch request command finished. When the PHY is resumed from
the state of power cut, the PHY is at a safe mode and the
OCP_PHY_PATCH_STAT wouldn't be updated. For this situation, it is
safe to set patch request command without waiting OCP_PHY_PATCH_STAT.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tobias Waldekranz [Tue, 2 Feb 2021 19:16:45 +0000 (20:16 +0100)]
net: dsa: xrs700x: Correctly address device over I2C
On read, master should send 31 MSB of the register (only even values
are ever used), followed by a 1 to indicate read. Then, reading two
bytes, the device will output the register's value.
On write, master sends 31 MSB of the register, followed by a 0 to
indicate write, followed by two bytes containing the register value.
Flexibilis' documentation (version 1.3) specifies the opposite
polarity (#read/write), but the scope indicates that it is, in fact,
read/#write.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Link: https://lore.kernel.org/r/20210202191645.439-1-tobias@waldekranz.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Wed, 3 Feb 2021 19:39:18 +0000 (21:39 +0200)]
net: dsa: bcm_sf2: Check egress tagging of CFP rule with proper accessor
The flow steering struct ethtool_flow_ext::data field is __be32, so when
the CFP code needs to check the VLAN egress tagging attribute in bit 0,
it does this in CPU native endianness. So logically, the endianness
conversion is set up the other way around, although in practice the same
result is produced.
Gets rid of build warning:
warning: cast from restricted __be32
warning: incorrect type in argument 1 (different base types)
expected unsigned int [usertype] val
got restricted __be32
warning: cast from restricted __be32
warning: cast from restricted __be32
warning: cast from restricted __be32
warning: cast from restricted __be32
warning: restricted __be32 degrades to integer
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210203193918.2236994-1-olteanv@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bhaskar Chowdhury [Thu, 4 Feb 2021 03:16:48 +0000 (08:46 +0530)]
drivers: net: ethernet: i825xx: Fix couple of spellings in the file ether1.c
s/initialsation/initialisation/
s/specifiing/specifying/
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20210204031648.27300-1-unixbhaskar@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Fri, 5 Feb 2021 02:38:01 +0000 (18:38 -0800)]
Merge branch 'fix-w-1-compilation-warnings-in-net-folder'
Leon Romanovsky says:
====================
Fix W=1 compilation warnings in net/* folder
Changelog:
v2:
* Patch 3: Added missing include file.
v1: https://lore.kernel.org/lkml/
20210203101612.
4004322-1-leon@kernel.org
* Removed Fixes lines.
* Changed target from net to be net-next.
* Patch 1: Moved function declaration to be outside config instead
games with if/endif.
* Patch 3: Moved declarations to new header file.
v0: https://lore.kernel.org/lkml/
20210202135544.
3262383-1-leon@kernel.org
====================
Link: https://lore.kernel.org/r/20210203135112.4083711-1-leon@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Leon Romanovsky [Wed, 3 Feb 2021 13:51:12 +0000 (15:51 +0200)]
netfilter: move handlers to net/ip_vs.h
Fix the following compilation warnings:
net/netfilter/ipvs/ip_vs_proto_tcp.c:147:1: warning: no previous prototype for 'tcp_snat_handler' [-Wmissing-prototypes]
147 | tcp_snat_handler(struct sk_buff *skb, struct ip_vs_protocol *pp,
| ^~~~~~~~~~~~~~~~
net/netfilter/ipvs/ip_vs_proto_udp.c:136:1: warning: no previous prototype for 'udp_snat_handler' [-Wmissing-prototypes]
136 | udp_snat_handler(struct sk_buff *skb, struct ip_vs_protocol *pp,
| ^~~~~~~~~~~~~~~~
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Leon Romanovsky [Wed, 3 Feb 2021 13:51:11 +0000 (15:51 +0200)]
net/core: move gro function declarations to separate header
Fir the following compilation warnings:
1031 | INDIRECT_CALLABLE_SCOPE void udp_v6_early_demux(struct sk_buff *skb)
net/ipv6/ip6_offload.c:182:41: warning: no previous prototype for ‘ipv6_gro_receive’ [-Wmissing-prototypes]
182 | INDIRECT_CALLABLE_SCOPE struct sk_buff *ipv6_gro_receive(struct list_head *head,
| ^~~~~~~~~~~~~~~~
net/ipv6/ip6_offload.c:320:29: warning: no previous prototype for ‘ipv6_gro_complete’ [-Wmissing-prototypes]
320 | INDIRECT_CALLABLE_SCOPE int ipv6_gro_complete(struct sk_buff *skb, int nhoff)
| ^~~~~~~~~~~~~~~~~
net/ipv6/ip6_offload.c:182:41: warning: no previous prototype for ‘ipv6_gro_receive’ [-Wmissing-prototypes]
182 | INDIRECT_CALLABLE_SCOPE struct sk_buff *ipv6_gro_receive(struct list_head *head,
| ^~~~~~~~~~~~~~~~
net/ipv6/ip6_offload.c:320:29: warning: no previous prototype for ‘ipv6_gro_complete’ [-Wmissing-prototypes]
320 | INDIRECT_CALLABLE_SCOPE int ipv6_gro_complete(struct sk_buff *skb, int nhoff)
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Leon Romanovsky [Wed, 3 Feb 2021 13:51:10 +0000 (15:51 +0200)]
ipv6: move udp declarations to net/udp.h
Fix the following compilation warning:
net/ipv6/udp.c:1031:30: warning: no previous prototype for 'udp_v6_early_demux' [-Wmissing-prototypes]
1031 | INDIRECT_CALLABLE_SCOPE void udp_v6_early_demux(struct sk_buff *skb)
| ^~~~~~~~~~~~~~~~~~
net/ipv6/udp.c:1072:29: warning: no previous prototype for 'udpv6_rcv' [-Wmissing-prototypes]
1072 | INDIRECT_CALLABLE_SCOPE int udpv6_rcv(struct sk_buff *skb)
| ^~~~~~~~~
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Leon Romanovsky [Wed, 3 Feb 2021 13:51:09 +0000 (15:51 +0200)]
ipv6: silence compilation warning for non-IPV6 builds
The W=1 compilation of allmodconfig generates the following warning:
net/ipv6/icmp.c:448:6: warning: no previous prototype for 'icmp6_send' [-Wmissing-prototypes]
448 | void icmp6_send(struct sk_buff *skb, u8 type, u8 code, __u32 info,
| ^~~~~~~~~~
Fix it by providing function declaration for builds with ipv6 as a module.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Colin Ian King [Wed, 3 Feb 2021 13:10:40 +0000 (13:10 +0000)]
net: hns3: remove redundant null check of an array
The null check of filp->f_path.dentry->d_iname is redundant because
it is an array of DNAME_INLINE_LEN chars and cannot be a null. Fix
this by removing the null check.
Addresses-Coverity: ("Array compared against 0")
Fixes: 04987ca1b9b6 ("net: hns3: add debugfs support for tm nodes, priority and qset info")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20210203131040.21656-1-colin.king@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
wengjianfeng [Wed, 3 Feb 2021 09:38:42 +0000 (17:38 +0800)]
nfc: pn533: Fix typo issue
change 'piority' to 'priority'
change 'succesfult' to 'successful'
Signed-off-by: wengjianfeng <wengjianfeng@yulong.com>
Link: https://lore.kernel.org/r/20210203093842.11180-1-samirweng1979@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Fri, 5 Feb 2021 02:37:18 +0000 (18:37 -0800)]
Merge branch 'net-enable-udp-v6-sockets-receiving-v4-packets-with-udp'
Xin Long says:
====================
net: enable udp v6 sockets receiving v4 packets with UDP
Currently, udp v6 socket can not process v4 packets with UDP GRO, as
udp_encap_needed_key is not increased when udp_tunnel_encap_enable()
is called for v6 socket.
This patchset is to increase it and remove the unnecessary code in
bareudp in Patch 1/2, and improve rxrpc encap_enable by calling
udp_tunnel_encap_enable().
====================
Link: https://lore.kernel.org/r/cover.1612342376.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Xin Long [Wed, 3 Feb 2021 08:54:23 +0000 (16:54 +0800)]
rxrpc: call udp_tunnel_encap_enable in rxrpc_open_socket
When doing encap_enable/increasing encap_needed_key, up->encap_enabled
is not set in rxrpc_open_socket(), and it will cause encap_needed_key
not being decreased in udpv6_destroy_sock().
This patch is to improve it by just calling udp_tunnel_encap_enable()
where it increases both UDP and UDPv6 encap_needed_key and sets
up->encap_enabled.
v4->v5:
- add the missing '#include <net/udp_tunnel.h>', as David Howells
noticed.
Acked-and-tested-by: David Howells <dhowells@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Xin Long [Wed, 3 Feb 2021 08:54:22 +0000 (16:54 +0800)]
udp: call udp_encap_enable for v6 sockets when enabling encap
When enabling encap for a ipv6 socket without udp_encap_needed_key
increased, UDP GRO won't work for v4 mapped v6 address packets as
sk will be NULL in udp4_gro_receive().
This patch is to enable it by increasing udp_encap_needed_key for
v6 sockets in udp_tunnel_encap_enable(), and correspondingly
decrease udp_encap_needed_key in udpv6_destroy_sock().
v1->v2:
- add udp_encap_disable() and export it.
v2->v3:
- add the change for rxrpc and bareudp into one patch, as Alex
suggested.
v3->v4:
- move rxrpc part to another patch.
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jian Yang [Mon, 1 Feb 2021 23:34:45 +0000 (15:34 -0800)]
net-loopback: set lo dev initial state to UP
Traditionally loopback devices come up with initial state as DOWN for
any new network-namespace. This would mean that anyone needing this
device would have to bring this UP by issuing something like 'ip link
set lo up'. This can be avoided if the initial state is set as UP.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: Jian Yang <jianyang@google.com>
Link: https://lore.kernel.org/r/20210201233445.2044327-1-jianyang.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Fri, 5 Feb 2021 02:20:17 +0000 (18:20 -0800)]
Merge branch 'net-consolidate-page_is_pfmemalloc-usage'
Alexander Lobakin says:
====================
net: consolidate page_is_pfmemalloc() usage
page_is_pfmemalloc() is used mostly by networking drivers to test
if a page can be considered for reusing/recycling.
It doesn't write anything to the struct page itself, so its sole
argument can be constified, as well as the first argument of
skb_propagate_pfmemalloc().
In Page Pool core code, it can be simply inlined instead.
Most of the callers from NIC drivers were just doppelgangers of
the same condition tests. Derive them into a new common function
do deduplicate the code.
Resend of v3 [2]:
- it missed Patchwork and Netdev archives, probably due to server-side
issues.
Since v2 [1]:
- use more intuitive name for the new inline function since there's
nothing "reserved" in remote pages (Jakub Kicinski, John Hubbard);
- fold likely() inside the helper itself to make driver code a bit
fancier (Jakub Kicinski);
- split function introduction and using into two separate commits;
- collect some more tags (Jesse Brandeburg, David Rientjes).
Since v1 [0]:
- new: reduce code duplication by introducing a new common function
to test if a page can be reused/recycled (David Rientjes);
- collect autographs for Page Pool bits (Jesper Dangaard Brouer,
Ilias Apalodimas).
[0] https://lore.kernel.org/netdev/
20210125164612.243838-1-alobakin@pm.me
[1] https://lore.kernel.org/netdev/
20210127201031.98544-1-alobakin@pm.me
[2] https://lore.kernel.org/lkml/
20210131120844.7529-1-alobakin@pm.me
====================
Link: https://lore.kernel.org/r/20210202133030.5760-1-alobakin@pm.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexander Lobakin [Tue, 2 Feb 2021 13:31:46 +0000 (13:31 +0000)]
net: page_pool: simplify page recycling condition tests
pool_page_reusable() is a leftover from pre-NUMA-aware times. For now,
this function is just a redundant wrapper over page_is_pfmemalloc(),
so inline it into its sole call site.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexander Lobakin [Tue, 2 Feb 2021 13:31:35 +0000 (13:31 +0000)]
net: use the new dev_page_is_reusable() instead of private versions
Now we can remove a bunch of identical functions from the drivers and
make them use common dev_page_is_reusable(). All {,un}likely() checks
are omitted since it's already present in this helper.
Also update some comments near the call sites.
Suggested-by: David Rientjes <rientjes@google.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Cc: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexander Lobakin [Tue, 2 Feb 2021 13:31:21 +0000 (13:31 +0000)]
net: introduce common dev_page_is_reusable()
A bunch of drivers test the page before reusing/recycling for two
common conditions:
- if a page was allocated under memory pressure (pfmemalloc page);
- if a page was allocated at a distant memory node (to exclude
slowdowns).
Introduce a new common inline for doing this, with likely() already
folded inside to make driver code a bit simpler.
Suggested-by: David Rientjes <rientjes@google.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Cc: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexander Lobakin [Tue, 2 Feb 2021 13:31:05 +0000 (13:31 +0000)]
skbuff: constify skb_propagate_pfmemalloc() "page" argument
The function doesn't write anything to the page struct itself,
so this argument can be const.
Misc: align second argument to the brace while at it.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexander Lobakin [Tue, 2 Feb 2021 13:30:54 +0000 (13:30 +0000)]
mm: constify page_is_pfmemalloc() argument
The function only tests for page->index, so its argument should be
const.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Brian Vazquez [Thu, 4 Feb 2021 18:18:39 +0000 (18:18 +0000)]
net: fix building errors on powerpc when CONFIG_RETPOLINE is not set
This commit fixes the errores reported when building for powerpc:
ERROR: modpost: "ip6_dst_check" [vmlinux] is a static EXPORT_SYMBOL
ERROR: modpost: "ipv4_dst_check" [vmlinux] is a static EXPORT_SYMBOL
ERROR: modpost: "ipv4_mtu" [vmlinux] is a static EXPORT_SYMBOL
ERROR: modpost: "ip6_mtu" [vmlinux] is a static EXPORT_SYMBOL
Fixes: f67fbeaebdc0 ("net: use indirect call helpers for dst_mtu")
Fixes: bbd807dfbf20 ("net: indirect call helpers for ipv4/ipv6 dst_check functions")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Brian Vazquez <brianvv@google.com>
Link: https://lore.kernel.org/r/20210204181839.558951-2-brianvv@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Brian Vazquez [Thu, 4 Feb 2021 18:18:38 +0000 (18:18 +0000)]
net: add EXPORT_INDIRECT_CALLABLE wrapper
When a static function is annotated with INDIRECT_CALLABLE_SCOPE and
CONFIG_RETPOLINE is set, the static keyword is removed. Sometimes the
function needs to be exported but EXPORT_SYMBOL can't be used because if
CONFIG_RETPOLINE is not set, we will attempt to export a static symbol.
This patch introduces a new indirect call wrapper:
EXPORT_INDIRECT_CALLABLE. This basically does EXPORT_SYMBOL when
CONFIG_RETPOLINE is set, but does nothing when it's not.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Brian Vazquez <brianvv@google.com>
Link: https://lore.kernel.org/r/20210204181839.558951-1-brianvv@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Marcelo Ricardo Leitner [Thu, 4 Feb 2021 01:48:16 +0000 (22:48 -0300)]
netlink: add tracepoint at NL_SET_ERR_MSG
Often userspace won't request the extack information, or they don't log it
because of log level or so, and even when they do, sometimes it's not
enough to know exactly what caused the error.
Netlink extack is the standard way of reporting erros with descriptive
error messages. With a trace point on it, we then can know exactly where
the error happened, regardless of userspace app. Also, we can even see if
the err msg was overwritten.
The wrapper do_trace_netlink_extack() is because trace points shouldn't be
called from .h files, as trace points are not that small, and the function
call to do_trace_netlink_extack() on the macros is not protected by
tracepoint_enabled() because the macros are called from modules, and this
would require exporting some trace structs. As this is error path, it's
better to export just the wrapper instead.
v2: removed leftover tracepoint declaration
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/4546b63e67b2989789d146498b13cc09e1fdc543.1612403190.git.marcelo.leitner@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jiapeng Chong [Tue, 2 Feb 2021 10:17:49 +0000 (18:17 +0800)]
drivers: net: xen-netfront: Simplify the calculation of variables
Fix the following coccicheck warnings:
./drivers/net/xen-netfront.c:1816:52-54: WARNING !A || A && B is
equivalent to !A || B.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/1612261069-13315-1-git-send-email-jiapeng.chong@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 4 Feb 2021 17:30:00 +0000 (09:30 -0800)]
Merge branch 'gtp'
Jonas Bonn says:
====================
There's ongoing work in this driver to provide support for IPv6, GRO,
GSO, and "collect metadata" mode operation. In order to facilitate this
work going forward, this short series accumulates already ACK:ed patches
that are ready for the next merge window.
All of these patches should be uncontroversial at this point, including
the first one in the series that reverts a recently added change to
introduce "collect metadata" mode. As that patch produces 'broken'
packets when common GTP headers are in place, it seems better to revert
it and rethink things a bit before inclusion.
====================
Link: https://lore.kernel.org/r/20210203070805.281321-1-jonas@norrbonn.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jonas Bonn [Wed, 3 Feb 2021 07:08:05 +0000 (08:08 +0100)]
gtp: update rx_length_errors for abnormally short packets
Based on work by Pravin Shelar.
Update appropriate stats when packet transmission isn't possible.
Signed-off-by: Jonas Bonn <jonas@norrbonn.se>
Acked-by: Harald Welte <laforge@gnumonks.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jonas Bonn [Wed, 3 Feb 2021 07:08:04 +0000 (08:08 +0100)]
gtp: set device type
Set the devtype to 'gtp' when setting up the link.
Signed-off-by: Jonas Bonn <jonas@norrbonn.se>
Acked-by: Harald Welte <laforge@gnumonks.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jonas Bonn [Wed, 3 Feb 2021 07:08:03 +0000 (08:08 +0100)]
gtp: drop unnecessary call to skb_dst_drop
The call to skb_dst_drop() is already done as part of udp_tunnel_xmit().
Signed-off-by: Jonas Bonn <jonas@norrbonn.se>
Acked-by: Harald Welte <laforge@gnumonks.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jonas Bonn [Wed, 3 Feb 2021 07:08:02 +0000 (08:08 +0100)]
gtp: really check namespaces before xmit
Blindly assuming that packet transmission crosses namespaces results in
skb marks being lost in the single namespace case.
Signed-off-by: Jonas Bonn <jonas@norrbonn.se>
Acked-by: Harald Welte <laforge@gnumonks.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jonas Bonn [Wed, 3 Feb 2021 07:08:01 +0000 (08:08 +0100)]
gtp: include role in link info
Querying link info for the GTP interface doesn't reveal in which "role" the
device is set to operate. Include this information in the info query
result.
Signed-off-by: Jonas Bonn <jonas@norrbonn.se>
Acked-by: Harald Welte <laforge@gnumonks.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jonas Bonn [Wed, 3 Feb 2021 07:08:00 +0000 (08:08 +0100)]
gtp: set initial MTU
The GTP link is brought up with a default MTU of zero. This can lead to
some rather unexpected behaviour for users who are more accustomed to
interfaces coming online with reasonable defaults.
This patch sets an initial MTU for the GTP link of 1500 less worst-case
tunnel overhead.
Signed-off-by: Jonas Bonn <jonas@norrbonn.se>
Acked-by: Harald Welte <laforge@gnumonks.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jonas Bonn [Wed, 3 Feb 2021 07:07:59 +0000 (08:07 +0100)]
Revert "GTP: add support for flow based tunneling API"
This reverts commit
9ab7e76aefc97a9aa664accb59d6e8dc5e52514a.
This patch was committed without maintainer approval and despite a number
of unaddressed concerns from review. There are several issues that
impede the acceptance of this patch and that make a reversion of this
particular instance of these changes the best way forward:
i) the patch contains several logically separate changes that would be
better served as smaller patches (for review purposes)
ii) functionality like the handling of end markers has been introduced
without further explanation
iii) symmetry between the handling of GTPv0 and GTPv1 has been
unnecessarily broken
iv) the patchset produces 'broken' packets when extension headers are
included
v) there are no available userspace tools to allow for testing this
functionality
vi) there is an unaddressed Coverity report against the patch concering
memory leakage
vii) most importantly, the patch contains a large amount of superfluous
churn that impedes other ongoing work with this driver
This patch will be reworked into a series that aligns with other
ongoing work and facilitates review.
Signed-off-by: Jonas Bonn <jonas@norrbonn.se>
Acked-by: Harald Welte <laforge@gnumonks.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Hariharan Ananthakrishnan [Fri, 29 Jan 2021 00:12:10 +0000 (00:12 +0000)]
net: tracepoint: exposing sk_family in all tcp:tracepoints
Similar to sock:inet_sock_set_state tracepoint, expose sk_family to
distinguish AF_INET and AF_INET6 families.
The following tcp tracepoints are updated:
tcp:tcp_destroy_sock
tcp:tcp_rcv_space_adjust
tcp:tcp_retransmit_skb
tcp:tcp_send_reset
tcp:tcp_receive_reset
tcp:tcp_retransmit_synack
tcp:tcp_probe
Signed-off-by: Hariharan Ananthakrishnan <hari@netflix.com>
Signed-off-by: Brendan Gregg <bgregg@netflix.com>
Link: https://lore.kernel.org/r/20210129001210.344438-1-hari@netflix.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Wei Wang [Tue, 2 Feb 2021 19:34:08 +0000 (11:34 -0800)]
tcp: use a smaller percpu_counter batch size for sk_alloc
Currently, a percpu_counter with the default batch size (2*nr_cpus) is
used to record the total # of active sockets per protocol. This means
sk_sockets_allocated_read_positive() could be off by +/-2*(nr_cpus^2).
This under/over-estimation could lead to wrong memory suppression
conditions in __sk_raise_mem_allocated().
Fix this by using a more reasonable fixed batch size of 16.
See related commit
cf86a086a180 ("net/dst: use a smaller percpu_counter
batch for dst entries accounting") that addresses a similar issue.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Link: https://lore.kernel.org/r/20210202193408.1171634-1-weiwan@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 4 Feb 2021 02:37:31 +0000 (18:37 -0800)]
Merge branch 'support-setting-lanes-via-ethtool'
Danielle Ratson says:
====================
Support setting lanes via ethtool
Some speeds can be achieved with different number of lanes. For example,
100Gbps can be achieved using two lanes of 50Gbps or four lanes of
25Gbps. This patchset adds a new selector that allows ethtool to
advertise link modes according to their number of lanes and also force a
specific number of lanes when autonegotiation is off.
Advertising all link modes with a speed of 100Gbps that use two lanes:
$ ethtool -s swp1 speed 100000 lanes 2 autoneg on
Forcing a speed of 100Gbps using four lanes:
$ ethtool -s swp1 speed 100000 lanes 4 autoneg off
====================
Link: https://lore.kernel.org/r/20210202180612.325099-1-danieller@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Danielle Ratson [Tue, 2 Feb 2021 18:06:12 +0000 (20:06 +0200)]
net: selftests: Add lanes setting test
Test that setting lanes parameter is working.
Set max speed and max lanes in the list of advertised link modes,
and then try to set max speed with the lanes below max lanes if exists
in the list.
And then, test that setting number of lanes larger than max lanes fails.
Do the above for both autoneg on and off.
$ ./ethtool_lanes.sh
TEST: 4 lanes is autonegotiated [ OK ]
TEST: Lanes number larger than max width is not set [ OK ]
TEST: Autoneg off, 4 lanes detected during force mode [ OK ]
TEST: Lanes number larger than max width is not set [ OK ]
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Danielle Ratson [Tue, 2 Feb 2021 18:06:11 +0000 (20:06 +0200)]
mlxsw: ethtool: Pass link mode in use to ethtool
Currently, when user space queries the link's parameters, as speed and
duplex, each parameter is passed from the driver to ethtool.
Instead, pass the link mode bit in use.
In Spectrum-1, simply pass the bit that is set to '1' from PTYS register.
In Spectrum-2, pass the first link mode bit in the mask of the used
link mode.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Danielle Ratson [Tue, 2 Feb 2021 18:06:10 +0000 (20:06 +0200)]
mlxsw: ethtool: Add support for setting lanes when autoneg is off
Currently, when auto negotiation is set to off, the user can force a
specific speed or both speed and duplex. The user cannot influence the
number of lanes that will be forced.
Add support for setting speed along with lanes so one would be able
to choose how many lanes will be forced.
When lanes parameter is passed from user space, choose the link mode
that its actual width equals to it.
Otherwise, the default link mode will be the one that supports the width
of the port.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Danielle Ratson [Tue, 2 Feb 2021 18:06:09 +0000 (20:06 +0200)]
mlxsw: ethtool: Remove max lanes filtering
Currently, when a speed can be supported by different number of lanes,
the supported link modes bitmask contains only link modes with a single
number of lanes.
This was done in order to prevent auto negotiation on number of
lanes after 50G-1-lane and 100G-2-lanes link modes were introduced.
For example, if a port's max width is 4, only link modes with 4 lanes
will be presented as supported by that port, so 100G is always achieved by
4 lanes of 25G.
After the previous patches that allow selection of the number of lanes,
auto negotiation on number of lanes becomes practical.
Remove that filtering of the maximum number of lanes supported link modes,
so indeed all the supported and advertised link modes will be shown.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Danielle Ratson [Tue, 2 Feb 2021 18:06:08 +0000 (20:06 +0200)]
ethtool: Expose the number of lanes in use
Currently, ethtool does not expose how many lanes are used when the
link is up.
After adding a possibility to advertise or force a specific number of
lanes, the lanes in use value can be either the maximum width of the port
or below.
Extend ethtool to expose the number of lanes currently in use for
drivers that support it.
For example:
$ ethtool -s swp1 speed 100000 lanes 4
$ ethtool -s swp2 speed 100000 lanes 4
$ ip link set swp1 up
$ ip link set swp2 up
$ ethtool swp1
Settings for swp1:
Supported ports: [ FIBRE Backplane ]
Supported link modes: 1000baseT/Full
10000baseT/Full
1000baseKX/Full
10000baseKR/Full
10000baseR_FEC
40000baseKR4/Full
40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
25000baseCR/Full
25000baseKR/Full
25000baseSR/Full
50000baseCR2/Full
50000baseKR2/Full
100000baseKR4/Full
100000baseSR4/Full
100000baseCR4/Full
100000baseLR4_ER4/Full
50000baseSR2/Full
10000baseCR/Full
10000baseSR/Full
10000baseLR/Full
10000baseER/Full
50000baseKR/Full
50000baseSR/Full
50000baseCR/Full
50000baseLR_ER_FR/Full
50000baseDR/Full
100000baseKR2/Full
100000baseSR2/Full
100000baseCR2/Full
100000baseLR2_ER2_FR2/Full
100000baseDR2/Full
200000baseKR4/Full
200000baseSR4/Full
200000baseLR4_ER4_FR4/Full
200000baseDR4/Full
200000baseCR4/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 1000baseT/Full
10000baseT/Full
1000baseKX/Full
1000baseKX/Full
10000baseKR/Full
10000baseR_FEC
40000baseKR4/Full
40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
25000baseCR/Full
25000baseKR/Full
25000baseSR/Full
50000baseCR2/Full
50000baseKR2/Full
100000baseKR4/Full
100000baseSR4/Full
100000baseCR4/Full
100000baseLR4_ER4/Full
50000baseSR2/Full
10000baseCR/Full
10000baseSR/Full
10000baseLR/Full
10000baseER/Full
200000baseKR4/Full
200000baseSR4/Full
200000baseLR4_ER4_FR4/Full
200000baseDR4/Full
200000baseCR4/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Advertised link modes: 100000baseKR4/Full
100000baseSR4/Full
100000baseCR4/Full
100000baseLR4_ER4/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: 100000Mb/s
Lanes: 4
Duplex: Full
Auto-negotiation: on
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Link detected: yes
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Danielle Ratson [Tue, 2 Feb 2021 18:06:07 +0000 (20:06 +0200)]
ethtool: Get link mode in use instead of speed and duplex parameters
Currently, when user space queries the link's parameters, as speed and
duplex, each parameter is passed from the driver to ethtool.
Instead, get the link mode bit in use, and derive each of the parameters
from it in ethtool.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Danielle Ratson [Tue, 2 Feb 2021 18:06:06 +0000 (20:06 +0200)]
ethtool: Extend link modes settings uAPI with lanes
Currently, when auto negotiation is on, the user can advertise all the
linkmodes which correspond to a specific speed, but does not have a
similar selector for the number of lanes. This is significant when a
specific speed can be achieved using different number of lanes. For
example, 2x50 or 4x25.
Add 'ETHTOOL_A_LINKMODES_LANES' attribute and expand 'struct
ethtool_link_settings' with lanes field in order to implement a new
lanes-selector that will enable the user to advertise a specific number
of lanes as well.
When auto negotiation is off, lanes parameter can be forced only if the
driver supports it. Add a capability bit in 'struct ethtool_ops' that
allows ethtool know if the driver can handle the lanes parameter when
auto negotiation is off, so if it does not, an error message will be
returned when trying to set lanes.
Example:
$ ethtool -s swp1 lanes 4
$ ethtool swp1
Settings for swp1:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseKX/Full
10000baseKR/Full
40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
25000baseCR/Full
25000baseSR/Full
50000baseCR2/Full
100000baseSR4/Full
100000baseCR4/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
100000baseSR4/Full
100000baseCR4/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: Unknown!
Duplex: Unknown! (255)
Auto-negotiation: on
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Link detected: no
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Danielle Ratson [Tue, 2 Feb 2021 18:06:05 +0000 (20:06 +0200)]
ethtool: Validate master slave configuration before rtnl_lock()
Create a new function for input validations to be called before
rtnl_lock() and move the master slave validation to that function.
This would be a cleanup for next patch that would add another validation
to the new function.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Tue, 2 Feb 2021 23:31:09 +0000 (01:31 +0200)]
net: dsa: fix SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING getting ignored
The bridge emits VLAN filtering events and quite a few others via
switchdev with orig_dev = br->dev. After the blamed commit, these events
started getting ignored.
The point of the patch was to not offload switchdev objects for ports
that didn't go through dsa_port_bridge_join, because the configuration
is unsupported:
- ports that offload a bonding/team interface go through
dsa_port_bridge_join when that bonding/team interface is later bridged
with another switch port or LAG
- ports that don't offload LAG don't get notified of the bridge that is
on top of that LAG.
Sadly, a check is missing, which is that the orig_dev is equal to the
bridge device. This check is compatible with the original intention,
because ports that don't offload bridging because they use a software
LAG don't have dp->bridge_dev set.
On a semi-related note, we should not offload switchdev objects or
populate dp->bridge_dev if the driver doesn't implement .port_bridge_join
either. However there is no regression associated with that, so it can
be done separately.
Fixes: 5696c8aedfcc ("net: dsa: Don't offload port attributes on standalone ports")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Tobias Waldekranz <tobias@waldekranz.com>
Tested-by: Tobias Waldekranz <tobias@waldekranz.com>
Link: https://lore.kernel.org/r/20210202233109.1591466-1-olteanv@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 4 Feb 2021 01:41:03 +0000 (17:41 -0800)]
Merge branch 'chelsio-cxgb-use-threaded-interrupts-for-deferred-work'
Sebastian Andrzej Siewior says:
====================
chelsio: cxgb: Use threaded interrupts for deferred work
Patch #2 fixes an issue in which del_timer_sync() and tasklet_kill() is
invoked from the interrupt handler. This is probably a rare error case
since it disables interrupts / the card in that case.
Patch #1 converts a worker to use a threaded interrupt which is then
also used in patch #2 instead adding another worker for this task (and
flush_work() to synchronise vs rmmod).
====================
Link: https://lore.kernel.org/r/20210202170104.1909200-1-bigeasy@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sebastian Andrzej Siewior [Tue, 2 Feb 2021 17:01:04 +0000 (18:01 +0100)]
chelsio: cxgb: Disable the card on error in threaded interrupt
t1_fatal_err() is invoked from the interrupt handler. The bad part is
that it invokes (via t1_sge_stop()) del_timer_sync() and tasklet_kill().
Both functions must not be called from an interrupt because it is
possible that it will wait for the completion of the timer/tasklet it
just interrupted.
In case of a fatal error, use t1_interrupts_disable() to disable all
interrupt sources and then wake the interrupt thread with
F_PL_INTR_SGE_ERR as pending flag. The threaded-interrupt will stop the
card via t1_sge_stop() and not re-enable the interrupts again.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sebastian Andrzej Siewior [Tue, 2 Feb 2021 17:01:03 +0000 (18:01 +0100)]
chelsio: cxgb: Replace the workqueue with threaded interrupt
The external interrupt (F_PL_INTR_EXT) needs to be handled in a process
context and this is accomplished by utilizing a workqueue.
The process context can also be provided by a threaded interrupt instead
of a workqueue. The threaded interrupt can be used later for other
interrupt related processing which require non-atomic context without
using yet another workqueue. free_irq() also ensures that the thread is
done which is currently missing (the worker could continue after the
module has been removed).
Save pending flags in pending_thread_intr. Use the same mechanism
to disable F_PL_INTR_EXT as interrupt source like it is used before the
worker is scheduled. Enable the interrupt again once
t1_elmer0_ext_intr_handler() is done.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 4 Feb 2021 01:31:35 +0000 (17:31 -0800)]
Merge branch 'support-for-octeontx2-98xx-cpt-block'
Srujana Challa says:
====================
Support for OcteonTX2 98xx CPT block.
OcteonTX2 series of silicons have multiple variants, the
98xx variant has two crypto (CPT) blocks to double the crypto
performance. This patchset adds support for new CPT block(CPT1).
====================
Link: https://lore.kernel.org/r/20210202152709.20450-1-schalla@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Srujana Challa [Tue, 2 Feb 2021 15:27:09 +0000 (20:57 +0530)]
octeontx2-af: Handle CPT function level reset
When FLR is initiated for a VF (PCI function level reset),
the parent PF gets a interrupt. PF then sends a message to
admin function (AF), which then cleans up all resources
attached to that VF. This patch adds support to handle
CPT FLR.
Signed-off-by: Narayana Prasad Raju Atherya <pathreya@marvell.com>
Signed-off-by: Suheil Chandran <schandran@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Srujana Challa [Tue, 2 Feb 2021 15:27:08 +0000 (20:57 +0530)]
octeontx2-af: Add support for CPT1 in debugfs
Adds support to display block CPT1 stats at
"/sys/kernel/debug/octeontx2/cpt1".
Signed-off-by: Mahipal Challa <mchalla@marvell.com>
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Srujana Challa [Tue, 2 Feb 2021 15:27:07 +0000 (20:57 +0530)]
octeontx2-af: Mailbox changes for 98xx CPT block
This patch changes CPT mailbox message format to
support new block CPT1 in 98xx silicon.
cpt_rd_wr_reg ->
Modify cpt_rd_wr_reg mailbox and its handler to
accommodate new block CPT1.
cpt_lf_alloc ->
Modify cpt_lf_alloc mailbox and its handler to
configure LFs from a block address out of multiple
blocks of same type. If a PF/VF needs to configure
LFs from both the blocks then this mbox should be
called twice.
Signed-off-by: Mahipal Challa <mchalla@marvell.com>
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Mike Looijmans [Tue, 2 Feb 2021 14:32:39 +0000 (15:32 +0100)]
net: mdiobus: Prevent spike on MDIO bus reset signal
The mdio_bus reset code first de-asserted the reset by allocating with
GPIOD_OUT_LOW, then asserted and de-asserted again. In other words, if
the reset signal defaulted to asserted, there'd be a short "spike"
before the reset.
Here is what happens depending on the pre-existing state of the reset
signal:
Reset (previously asserted): ~~~|_|~~~~|_______
Reset (previously deasserted): _____|~~~~|_______
^ ^ ^
A B C
At point A, the low going transition is because the reset line is
requested using GPIOD_OUT_LOW. If the line is successfully requested,
the first thing we do is set it high _without_ any delay. This is
point B. So, a glitch occurs between A and B.
We then fsleep() and finally set the GPIO low at point C.
Requesting the line using GPIOD_OUT_HIGH eliminates the A and B
transitions. Instead we get:
Reset (previously asserted) : ~~~~~~~~~~|______
Reset (previously deasserted): ____|~~~~~|______
^ ^
A C
Where A and C are the points described above in the code. Point B
has been eliminated.
The issue was found when we pulled down the reset signal for the
Marvell 88E1512P PHY (because it requires at least 50ms after POR with
an active clock). Looking at the reset signal with a scope revealed a
short spike, point B in the artwork above.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210202143239.10714-1-mike.looijmans@topic.nl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Dan Carpenter [Tue, 2 Feb 2021 09:13:44 +0000 (12:13 +0300)]
net: mscc: ocelot: fix error code in mscc_ocelot_probe()
Probe should return an error code if platform_get_irq_byname() fails
but it returns success instead.
Fixes: 6c30384eb1de ("net: mscc: ocelot: register devlink ports")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/YBkXyFIl4V9hgxYM@mwanda
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Dan Carpenter [Tue, 2 Feb 2021 09:12:38 +0000 (12:12 +0300)]
net: mscc: ocelot: fix error handling bugs in mscc_ocelot_init_ports()
There are several error handling bugs in mscc_ocelot_init_ports(). I
went through the code, and carefully audited it and made fixes and
cleanups.
1) The ocelot_probe_port() function didn't have a mirror release function
so it was hard to follow. I created the ocelot_release_port()
function.
2) In the ocelot_probe_port() function, if the register_netdev() call
failed, then it lead to a double free_netdev(dev) bug. Fix this by
setting "ocelot->ports[port] = NULL" on the error path.
3) I was concerned that the "port" which comes from of_property_read_u32()
might be out of bounds so I added a check for that.
4) In the original code if ocelot_regmap_init() failed then the driver
tried to continue but I think that should be a fatal error.
5) If ocelot_probe_port() failed then the most recent devlink was leaked.
The fix for mostly came Vladimir Oltean. Get rid of "registered_ports"
and just set a bit in "devlink_ports_registered" to say when the
devlink port has been registered (and needs to be unregistered on
error). There are fewer than 32 ports so a u32 is large enough for
this purpose.
6) The error handling if the final ocelot_port_devlink_init() failed had
two problems. The "while (port-- >= 0)" loop should have been
"--port" pre-op instead of a post-op to avoid a buffer underflow.
The "if (!registered_ports[port])" condition was reversed leading to
resource leaks and double frees.
Fixes: 6c30384eb1de ("net: mscc: ocelot: register devlink ports")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/YBkXhqRxHtRGzSnJ@mwanda
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 3 Feb 2021 22:51:41 +0000 (14:51 -0800)]
Merge branch 'net-use-indirect_call-in-some-dst_ops'
Brian Vazquez says:
====================
net: use INDIRECT_CALL in some dst_ops
This patch series uses the INDIRECT_CALL wrappers in some dst_ops
functions to mitigate retpoline costs. Benefits depend on the
platform as described below.
Background: The kernel rewrites the retpoline code at
__x86_indirect_thunk_r11 depending on the CPU's requirements.
The INDIRECT_CALL wrappers provide hints on possible targets and
save the retpoline overhead using a direct call in case the
target matches one of the hints.
The retpoline overhead for the following three cases has been
measured by Luigi Rizzo in microbenchmarks, using CPU performance
counters, and cover reasonably well the range of possible retpoline
overheads compared to a plain indirect call (in equal conditions,
specifically with predicted branch, hot cache):
- just "jmp *(%r11)" on modern platforms like Intel Cascadelake.
In this case the overhead is just 2 clock cycles:
- "lfence; jmp *(%r11)" on e.g. some recent AMD CPUs.
In this case the lfence is blocked until pending reads complete,
so the actual overhead depends on previous instructions.
The best case we have measured 15 clock cycles of overhead.
- worst case, e.g. skylake, the full retpoline is used
__x86_indirect_thunk_r11: call set_u_target
capture_speculation: pause
lfence
jmp capture_speculation
.align 16
set_up_target: mov %r11, (%rsp)
ret
In this case the overhead has been measured in 35-40 clock cycles.
The actual time saved hence depends on the platform and current
clock speed (which varies heavily, especially when C-states are active).
Also note that actual benefit might be lower than expected if the
longer retpoline overlaps with some pending memory read.
MEASUREMENTS:
The INDIRECT_CALL wrappers in this patchset involve the processing
of incoming SYN and generation of syncookies. Hence, the test has been
run by configuring a receiving host with a single NIC rx queue, disabling
RPS and RFS so that all processing occurs on the same core.
An external source generates SYN fast enough to saturate the receiving CPU.
We ran two sets of experiments, with and without the dst_output patch,
comparing the number of syncookies generated over a 20s period
in multiple runs.
Assuming the CPU is saturated, the time per packet is
t = number_of_packets/total_time
and if the two datasets have statistically meaningful difference,
the difference in times between the two cases gives an estimate
of the benefits from one INDIRECT_CALL.
Here are the experimental results:
Skylake Syncookies over 20s (5 tests)
---------------------------------------------------
indirect
9166325 9182023 9170093 9134014 9171082
retpoline
9099308 9126350 9154841 9056377 9122376
Computing the stats on the ns_pkt = 20e6/total_packets gives the following:
$ ministat -c 95 -w 70 /tmp/sk-indirect /tmp/sk-retp
x /tmp/sk-indirect
+ /tmp/sk-retp
+----------------------------------------------------------------------+
|x xx x + x + + + +|
||______M__A_______|_|____________M_____A___________________| |
+----------------------------------------------------------------------+
N Min Max Median Avg Stddev
x 5 2.17817e-06 2.18962e-06 2.181e-06 2.
182292e-06 4.
3252133e-09
+ 5 2.18464e-06 2.20839e-06 2.19241e-06 2.
194974e-06 8.
8695958e-09
Difference at 95.0% confidence
1.2682e-08 +/- 1.01766e-08
0.581132% +/- 0.466326%
(Student's t, pooled s = 6.97772e-09)
This suggests a difference of 13ns +/- 10ns
Our expectation from microbenchmarks was 35-40 cycles per call,
but part of the gains may be eaten by stalls from pending memory reads.
For Cascadelake:
Cascadelake Syncookies over 20s (5 tests)
---------------------------------------------------------
indirect
10339797 10297547 10366826 10378891 10384854
retpoline
10332674 10366805 10320374 10334272 10374087
Computing the stats on the ns_pkt = 20e6/total_packets gives no
meaningful difference even at just 80% (this was expected):
$ ministat -c 80 -w 70 /tmp/cl-indirect /tmp/cl-retp
x /tmp/cl-indirect
+ /tmp/cl-retp
+----------------------------------------------------------------------+
| x x + * x + + + x|
||______________|_M_________A_____A_______M________|___| |
+----------------------------------------------------------------------+
N Min Max Median Avg Stddev
x 5 1.92588e-06 1.94221e-06 1.92923e-06 1.
931716e-06 6.
6936746e-09
+ 5 1.92788e-06 1.93791e-06 1.93531e-06 1.
933188e-06 4.
3734106e-09
No difference proven at 80.0% confidence
====================
Link: https://lore.kernel.org/r/20210201174132.3534118-1-brianvv@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Brian Vazquez [Mon, 1 Feb 2021 17:41:32 +0000 (17:41 +0000)]
net: indirect call helpers for ipv4/ipv6 dst_check functions
This patch avoids the indirect call for the common case:
ip6_dst_check and ipv4_dst_check
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Brian Vazquez [Mon, 1 Feb 2021 17:41:31 +0000 (17:41 +0000)]
net: use indirect call helpers for dst_mtu
This patch avoids the indirect call for the common case:
ip6_mtu and ipv4_mtu
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Brian Vazquez [Mon, 1 Feb 2021 17:41:30 +0000 (17:41 +0000)]
net: use indirect call helpers for dst_output
This patch avoids the indirect call for the common case:
ip6_output and ip_output
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Brian Vazquez [Mon, 1 Feb 2021 17:41:29 +0000 (17:41 +0000)]
net: use indirect call helpers for dst_input
This patch avoids the indirect call for the common case:
ip_local_deliver and ip6_input
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Emil Renner Berthing [Sat, 30 Jan 2021 23:46:37 +0000 (00:46 +0100)]
net: usb: cdc_ncm: use new API for bh tasklet
This converts the driver to use the new tasklet API introduced in
commit
12cc923f1ccc ("tasklet: Introduce new initialization API")
It is unfortunate that we need to add a pointer to the driver context to
get back to the usbnet device, but the space will be reclaimed once
there are no more users of the old API left and we can remove the data
value and flag from the tasklet struct.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210130234637.26505-1-kernel@esmil.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Geert Uytterhoeven [Tue, 2 Feb 2021 13:06:50 +0000 (14:06 +0100)]
net: fec: Silence M5272 build warnings
If CONFIG_M5272=y:
drivers/net/ethernet/freescale/fec_main.c: In function ‘fec_restart’:
drivers/net/ethernet/freescale/fec_main.c:948:6: warning: unused variable ‘val’ [-Wunused-variable]
948 | u32 val;
| ^~~
drivers/net/ethernet/freescale/fec_main.c: In function ‘fec_get_mac’:
drivers/net/ethernet/freescale/fec_main.c:1667:28: warning: unused variable ‘pdata’ [-Wunused-variable]
1667 | struct fec_platform_data *pdata = dev_get_platdata(&fep->pdev->dev);
| ^~~~~
Fix this by moving the variable declarations inside the existing #ifdef
blocks.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210202130650.865023-1-geert@linux-m68k.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet [Tue, 2 Feb 2021 15:41:45 +0000 (07:41 -0800)]
inet: do not export inet_gro_{receive|complete}
inet_gro_receive() and inet_gro_complete() are part
of GRO engine which can not be modular.
Similarly, inet_gso_segment() does not need to be exported,
being part of GSO stack.
In other words, net/ipv6/ip6_offload.o is part of vmlinux,
regardless of CONFIG_IPV6.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20210202154145.1568451-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 3 Feb 2021 02:40:41 +0000 (18:40 -0800)]
Merge tag 'mac80211-next-for-net-next-2021-02-02' of git://git./linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time, only RTNL locking reduction fallout.
- cfg80211_dev_rename() requires RTNL
- cfg80211_change_iface() and cfg80211_set_encryption()
require wiphy mutex (was missing in wireless extensions)
- cfg80211_destroy_ifaces() requires wiphy mutex
- netdev registration can fail due to notifiers, and then
notifiers are "unrolled", need to handle this properly
* tag 'mac80211-next-for-net-next-2021-02-02' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next:
cfg80211: fix netdev registration deadlock
cfg80211: call cfg80211_destroy_ifaces() with wiphy lock held
wext: call cfg80211_set_encryption() with wiphy lock held
wext: call cfg80211_change_iface() with wiphy lock held
nl80211: call cfg80211_dev_rename() under RTNL
====================
Link: https://lore.kernel.org/r/20210202144106.38207-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 3 Feb 2021 02:38:53 +0000 (18:38 -0800)]
Merge tag 'mlx5-updates-2021-02-01' of git://git./linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2021-02-01
mlx5 netdev updates:
1) Trivial refactoring ahead of the upcoming uplink representor series.
2) Increased RSS table size to 256, for better results
3) Misc. Cleanup and very trivial improvements
* tag 'mlx5-updates-2021-02-01' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: DR, Avoid unnecessary csum recalculation on supporting devices
net/mlx5e: CT: remove useless conversion to PTR_ERR then ERR_PTR
net/mlx5e: accel, remove redundant space
net/mlx5e: kTLS, Improve TLS RX workqueue scope
net/mlx5e: remove h from printk format specifier
net/mlx5e: Increase indirection RQ table size to 256
net/mlx5e: Enable napi in channel's activation stage
net/mlx5e: Move representor neigh init into profile enable
net/mlx5e: Avoid false lock depenency warning on tc_ht
net/mlx5e: Move set vxlan nic info to profile init
net/mlx5e: Move netif_carrier_off() out of mlx5e_priv_init()
net/mlx5e: Refactor mlx5e_netdev_init/cleanup to mlx5e_priv_init/cleanup
net/mxl5e: Add change profile method
net/mlx5e: Separate between netdev objects and mlx5e profiles initialization
====================
Link: https://lore.kernel.org/r/20210202065457.613312-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 3 Feb 2021 02:37:21 +0000 (18:37 -0800)]
Merge branch 'mptcp-add_addr-enhancements'
Mat Martineau says:
====================
mptcp: ADD_ADDR enhancements
This patch series from the MPTCP tree contains enhancements and
associated tests for the ADD_ADDR ("add address") MPTCP option. This
option allows already-connected MPTCP peers to share additional IP
addresses with each other, which can then be used to create additional
subflows within those MPTCP connections.
Patches 1 & 2 remove duplicated data in the per-connection path manager
structure.
Patches 3-6 initiate additional subflows when an address is added using
the netlink path manager interface and improve ADD_ADDR signaling
reliability, subject to configured limits. Self tests are also updated.
Patches 7-15 add new support for optional port numbers in ADD_ADDR. This
includes creating an additional in-kernel TCP listening socket for the
requested port number, validating the port number when processing
incoming subflow connections, including the port number in netlink
interfaces, and adding some new MIBs. New self test cases are added for
subflows connecting with alternate port numbers.
====================
Link: https://lore.kernel.org/r/20210201230920.66027-1-mathew.j.martineau@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Geliang Tang [Mon, 1 Feb 2021 23:09:20 +0000 (15:09 -0800)]
selftests: mptcp: add testcases for ADD_ADDR with port
This patch adds testcases for ADD_ADDR with port and the related MIB
counters check in chk_add_nr. The output looks like this:
24 signal address with port syn[ ok ] - synack[ ok ] - ack[ ok ]
add[ ok ] - echo [ ok ] - pt [ ok ]
syn[ ok ] - synack[ ok ] - ack[ ok ]
syn[ ok ] - ack [ ok ]
25 subflow and signal with port syn[ ok ] - synack[ ok ] - ack[ ok ]
add[ ok ] - echo [ ok ] - pt [ ok ]
syn[ ok ] - synack[ ok ] - ack[ ok ]
syn[ ok ] - ack [ ok ]
26 remove single address with port syn[ ok ] - synack[ ok ] - ack[ ok ]
add[ ok ] - echo [ ok ] - pt [ ok ]
syn[ ok ] - synack[ ok ] - ack[ ok ]
syn[ ok ] - ack [ ok ]
rm [ ok ] - sf [ ok ]
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Geliang Tang [Mon, 1 Feb 2021 23:09:19 +0000 (15:09 -0800)]
mptcp: add the mibs for ADD_ADDR with port
This patch adds the mibs for ADD_ADDR with port:
MPTCP_MIB_PORTADD for received ADD_ADDR suboption with a port number.
MPTCP_MIB_PORTSYNRX, MPTCP_MIB_PORTSYNACKRX, MPTCP_MIB_PORTACKRX, for
received MP_JOIN's SYN or SYN/ACK or ACK with a port number which is
different from the msk's port number.
MPTCP_MIB_MISMATCHPORTSYNRX and MPTCP_MIB_MISMATCHPORTACKRX, for
received SYN or ACK MP_JOIN with a mismatched port-number.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Geliang Tang [Mon, 1 Feb 2021 23:09:18 +0000 (15:09 -0800)]
selftests: mptcp: add port argument for pm_nl_ctl
This patch adds a new argument for pm_nl_ctl tool. We can use it like
this:
# pm_nl_ctl add 10.0.2.1 flags signal port 10100
# pm_nl_ctl dump
id 1 flags signal 10.0.2.1 10100
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Geliang Tang [Mon, 1 Feb 2021 23:09:17 +0000 (15:09 -0800)]
mptcp: deal with MPTCP_PM_ADDR_ATTR_PORT in PM netlink
This patch adds MPTCP_PM_ADDR_ATTR_PORT filling and parsing in PM
netlink.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Geliang Tang [Mon, 1 Feb 2021 23:09:16 +0000 (15:09 -0800)]
mptcp: enable use_port when invoke addresses_equal
When dealing with the addresses list local_addr_list or anno_list, we
should enable the function addresses_equal's parameter use_port. And
enable it in address_zero too.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Geliang Tang [Mon, 1 Feb 2021 23:09:15 +0000 (15:09 -0800)]
mptcp: add port number check for MP_JOIN
This patch adds two new helpers, subflow_use_different_sport and
subflow_use_different_dport, to check whether the subflow's source or
destination port number is different from the msk's port number. When
receiving the MP_JOIN's SYN/SYNACK/ACK, we do these port number checks
and print out the different port numbers.
And furthermore, when receiving the MP_JOIN's SYN/ACK, we also use a new
helper mptcp_pm_sport_in_anno_list to check whether this port number is
announced. If it isn't, we need to abort this connection.
This patch also populates the local address's port field in
local_address.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Geliang Tang [Mon, 1 Feb 2021 23:09:14 +0000 (15:09 -0800)]
mptcp: add a new helper subflow_req_create_thmac
This patch adds a new helper named subflow_req_create_thmac, which is
extracted from subflow_token_join_request. It initializes subflow_req's
local_nonce and thmac fields, those are the more expensive to populate.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Geliang Tang [Mon, 1 Feb 2021 23:09:13 +0000 (15:09 -0800)]
mptcp: drop unused skb in subflow_token_join_request
This patch drops the unused parameter skb in subflow_token_join_request.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Geliang Tang [Mon, 1 Feb 2021 23:09:12 +0000 (15:09 -0800)]
mptcp: create the listening socket for new port
This patch creates a listening socket when an address with a port-number
is added by PM netlink. Then binds the new port to the socket, and
listens for new connections.
When the address is removed or the addresses are flushed by PM netlink,
release the listening socket.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Geliang Tang [Mon, 1 Feb 2021 23:09:11 +0000 (15:09 -0800)]
selftests: mptcp: add testcases for newly added addresses
This patch adds testcases to create subflows or signal addresses for the
newly added IPv4 or IPv6 addresses.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Geliang Tang [Mon, 1 Feb 2021 23:09:10 +0000 (15:09 -0800)]
selftests: mptcp: use minus values for removing address numbers
This patch changes the removing addresses numbers to minus values, left
the plus values for the adding addresses numbers.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Geliang Tang [Mon, 1 Feb 2021 23:09:09 +0000 (15:09 -0800)]
mptcp: send ack for every add_addr
This patch changes the sending ACK conditions for the ADD_ADDR, send an
ACK packet for any ADD_ADDR, not just when ipv6 addresses or port
numbers are included.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/139
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Geliang Tang [Mon, 1 Feb 2021 23:09:08 +0000 (15:09 -0800)]
mptcp: create subflow or signal addr for newly added address
Currently, when a new MPTCP endpoint is added, the existing MPTCP
sockets are not affected.
This patch implements a new function mptcp_nl_add_subflow_or_signal_addr,
invoked when an address is added from PM netlink. This function traverses
the MPTCP sockets list and invokes mptcp_pm_create_subflow_or_signal_addr
to try to create a subflow or signal an address for the newly added
address, if local constraint allows that.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/19
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Geliang Tang [Mon, 1 Feb 2021 23:09:07 +0000 (15:09 -0800)]
mptcp: drop *_max fields in mptcp_pm_data
This patch drops the per-msk values add_addr_signal_max,
add_addr_accept_max, local_addr_max and subflows_max fields in struct
mptcp_pm_data, uses the pernet *_max values instead. And adds four new
helpers to get the pernet *_max values separately.
Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Geliang Tang [Mon, 1 Feb 2021 23:09:06 +0000 (15:09 -0800)]
mptcp: use WRITE_ONCE for the pernet *_max
This patch uses WRITE_ONCE() for all the pernet add_addr_signal_max,
add_addr_accept_max, local_addr_max and subflows_max fields in struct
pm_nl_pernet to avoid concurrency issues.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kai-Heng Feng [Tue, 2 Feb 2021 04:48:12 +0000 (12:48 +0800)]
r8169: Add support for another RTL8168FP
According to the vendor driver, the new chip with XID 0x54b is
essentially the same as the one with XID 0x54a, but it doesn't need the
firmware.
So add support accordingly.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/20210202044813.1304266-1-kai.heng.feng@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 3 Feb 2021 01:46:01 +0000 (17:46 -0800)]
Merge branch 'add-notifications-when-route-hardware-flags-change'
Ido Schimmel says:
====================
Add notifications when route hardware flags change
Routes installed to the kernel can be programmed to capable devices, in
which case they are marked with one of two flags. RTM_F_OFFLOAD for
routes that offload traffic from the kernel and RTM_F_TRAP for routes
that trap packets to the kernel for processing (e.g., host routes).
These flags are of interest to routing daemons since they would like to
delay advertisement of routes until they are installed in hardware. This
allows them to avoid packet loss or misrouted packets. Currently,
routing daemons do not receive any notifications when these flags are
changed, requiring them to poll the kernel tables for changes which is
inefficient.
This series addresses the issue by having the kernel emit RTM_NEWROUTE
notifications whenever these flags change. The behavior is controlled by
two sysctls (net.ipv4.fib_notify_on_flag_change and
net.ipv6.fib_notify_on_flag_change) that default to 0 (no
notifications).
Note that even if route installation in hardware is improved to be more
synchronous, these notifications are still of interest. For example, a
multipath route can change from RTM_F_OFFLOAD to RTM_F_TRAP if its
neighbours become invalid. A routing daemon can choose to withdraw /
replace the route in that case. In addition, the deletion of a route
from the kernel can prompt the installation of an identical route
(already in kernel, with an higher metric) to hardware.
For testing purposes, netdevsim is aligned to simulate a "real" driver
that programs routes to hardware.
Series overview:
Patches #1-#2 align netdevsim to perform route programming in a
non-atomic context
Patches #3-#5 add sysctl to control IPv4 notifications
Patches #6-#8 add sysctl to control IPv6 notifications
Patch #9 extends existing fib tests to set sysctls before running tests
Patch #10 adds test for fib notifications over netdevsim
====================
Link: https://lore.kernel.org/r/20210201194757.3463461-1-idosch@idosch.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Amit Cohen [Mon, 1 Feb 2021 19:47:57 +0000 (21:47 +0200)]
selftests: netdevsim: Add fib_notifications test
Add test to check fib notifications behavior.
The test checks route addition, route deletion and route replacement for
both IPv4 and IPv6.
When fib_notify_on_flag_change=0, expect single notification for route
addition/deletion/replacement.
When fib_notify_on_flag_change=1, expect:
- two notification for route addition/replacement, first without RTM_F_TRAP
and second with RTM_F_TRAP.
- single notification for route deletion.
$ ./fib_notifications.sh
TEST: IPv4 route addition [ OK ]
TEST: IPv4 route deletion [ OK ]
TEST: IPv4 route replacement [ OK ]
TEST: IPv6 route addition [ OK ]
TEST: IPv6 route deletion [ OK ]
TEST: IPv6 route replacement [ OK ]
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Amit Cohen [Mon, 1 Feb 2021 19:47:56 +0000 (21:47 +0200)]
selftests: Extend fib tests to run with and without flags notifications
Run the test cases with both `fib_notify_on_flag_change` sysctls set to
'1', and then with both sysctls set to '0' to verify there are no
regressions in the test when notifications are added.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Amit Cohen [Mon, 1 Feb 2021 19:47:55 +0000 (21:47 +0200)]
net: ipv6: Emit notification when fib hardware flags are changed
After installing a route to the kernel, user space receives an
acknowledgment, which means the route was installed in the kernel,
but not necessarily in hardware.
The asynchronous nature of route installation in hardware can lead
to a routing daemon advertising a route before it was actually installed in
hardware. This can result in packet loss or mis-routed packets until the
route is installed in hardware.
It is also possible for a route already installed in hardware to change
its action and therefore its flags. For example, a host route that is
trapping packets can be "promoted" to perform decapsulation following
the installation of an IPinIP/VXLAN tunnel.
Emit RTM_NEWROUTE notifications whenever RTM_F_OFFLOAD/RTM_F_TRAP flags
are changed. The aim is to provide an indication to user-space
(e.g., routing daemons) about the state of the route in hardware.
Introduce a sysctl that controls this behavior.
Keep the default value at 0 (i.e., do not emit notifications) for several
reasons:
- Multiple RTM_NEWROUTE notification per-route might confuse existing
routing daemons.
- Convergence reasons in routing daemons.
- The extra notifications will negatively impact the insertion rate.
- Not all users are interested in these notifications.
Move fib6_info_hw_flags_set() to C file because it is no longer a short
function.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Amit Cohen [Mon, 1 Feb 2021 19:47:54 +0000 (21:47 +0200)]
net: Do not call fib6_info_hw_flags_set() when IPv6 is disabled
With the next patch mlxsw and netdevsim will fail in compilation if
CONFIG_IPV6 is disabled.
Do not call fib6_info_hw_flags_set() when IPv6 is disabled.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Amit Cohen [Mon, 1 Feb 2021 19:47:53 +0000 (21:47 +0200)]
net: Pass 'net' struct as first argument to fib6_info_hw_flags_set()
The next patch will emit notification when hardware flags are changed,
in case that fib_notify_on_flag_change sysctl is set to 1.
To know sysctl values, net struct is needed.
This change is consistent with the IPv4 version, which gets 'net' struct
as its first argument.
Currently, the only callers of this function are mlxsw and netdevsim.
Patch the callers to pass net.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Amit Cohen [Mon, 1 Feb 2021 19:47:52 +0000 (21:47 +0200)]
net: ipv4: Emit notification when fib hardware flags are changed
After installing a route to the kernel, user space receives an
acknowledgment, which means the route was installed in the kernel,
but not necessarily in hardware.
The asynchronous nature of route installation in hardware can lead to a
routing daemon advertising a route before it was actually installed in
hardware. This can result in packet loss or mis-routed packets until the
route is installed in hardware.
It is also possible for a route already installed in hardware to change
its action and therefore its flags. For example, a host route that is
trapping packets can be "promoted" to perform decapsulation following
the installation of an IPinIP/VXLAN tunnel.
Emit RTM_NEWROUTE notifications whenever RTM_F_OFFLOAD/RTM_F_TRAP flags
are changed. The aim is to provide an indication to user-space
(e.g., routing daemons) about the state of the route in hardware.
Introduce a sysctl that controls this behavior.
Keep the default value at 0 (i.e., do not emit notifications) for several
reasons:
- Multiple RTM_NEWROUTE notification per-route might confuse existing
routing daemons.
- Convergence reasons in routing daemons.
- The extra notifications will negatively impact the insertion rate.
- Not all users are interested in these notifications.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Acked-by: Roopa Prabhu <roopa@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Amit Cohen [Mon, 1 Feb 2021 19:47:51 +0000 (21:47 +0200)]
net: ipv4: Publish fib_nlmsg_size()
Publish fib_nlmsg_size() to allow it to be used later on from
fib_alias_hw_flags_set().
Remove the inline keyword since it shouldn't be used inside C files.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Amit Cohen [Mon, 1 Feb 2021 19:47:50 +0000 (21:47 +0200)]
net: ipv4: Pass fib_rt_info as const to fib_dump_info()
fib_dump_info() does not change 'fri', so pass it as 'const'.
It will later allow us to invoke fib_dump_info() from
fib_alias_hw_flags_set().
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Amit Cohen [Mon, 1 Feb 2021 19:47:49 +0000 (21:47 +0200)]
netdevsim: fib: Perform the route programming in a non-atomic context
Currently, netdevsim implements dummy FIB offload and marks notified
routes with RTM_F_TRAP flag. netdevsim does not defer route notifications
to a work queue because it does not need to program any hardware.
Given that netdevsim's purpose is to both give an example implementation
and allow developers to test their code, align netdevsim to a "real"
hardware device driver like mlxsw and have it also perform the route
"programming" in a non-atomic context.
It will be used to test route flags notifications which will be added in
the next patches.
The following changes are needed when route handling is performed in WQ:
- Handle the accounting in the main context, to be able to return an
error for adding route when all the routes are used.
For FIB_EVENT_ENTRY_REPLACE increase the counter before scheduling
the delayed work, and in case that this event replaces an existing route,
decrease the counter as part of the delayed work.
- For IPv6, cannot use fen6_info->rt->fib6_siblings list because it
might be changed during handling the delayed work.
Save an array with the nexthops as part of fib6_event struct, and take
a reference for each nexthop to prevent them from being freed while
event is queued.
- Change GFP_ATOMIC allocations to GFP_KERNEL.
- Use single work item that is handling a list of ordered routes.
Handling routes must be processed in the order they were submitted to
avoid logical errors that could lead to unexpected failures.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Amit Cohen [Mon, 1 Feb 2021 19:47:48 +0000 (21:47 +0200)]
netdevsim: fib: Convert the current occupancy to an atomic variable
When route is added/deleted, the appropriate counter is increased/decreased
to maintain number of routes.
User can limit the number of routes and then according to the appropriate
counter, adding more routes than the limitation is forbidden.
Currently, there is one lock which protects hashtable, list and accounting.
Handling the counters will be performed from both atomic context and
non-atomic context, while the hashtable and the list will be used only from
non-atomic context and therefore will be protected by a separate lock.
Protect accounting by using an atomic variable, so lock is not needed.
v2:
* Use atomic64_sub() in nsim_nexthop_account()'s error path
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 3 Feb 2021 01:42:37 +0000 (17:42 -0800)]
Merge branch 'net-ipa-don-t-disable-napi-in-suspend'
Alex Elder says:
====================
net: ipa: don't disable NAPI in suspend
This is version 2 of a series that reworks the order in which things
happen during channel stop and suspend (and start and resume), in
order to address a hang that has been observed during suspend.
The introductory message on the first version of the series gave
some history which is omitted here.
The end result of this series is that we only enable NAPI and the
I/O completion interrupt on a channel when we start the channel for
the first time. And we only disable them when stopping the channel
"for good." In other words, NAPI and the completion interrupt
remain enabled while a channel is stopped for suspend.
One comment on version 1 of the series suggested *not* returning
early on success in a function, instead having both success and
error paths return from the same point at the end of the function
block. This has been addressed in this version.
In addition, this version consolidates things a little bit, but the
net result of the series is exactly the same as version 1 (with the
exception of the return fix mentioned above).
First, patch 6 in the first version was a small step to make patch 7
easier to understand. The two have been combined now.
Second, previous version moved (and for suspend/resume, eliminated)
I/O completion interrupt and NAPI disable/enable control in separate
steps (patches). Now both are moved around together in patch 5 and
6, which eliminates the need for the final (NAPI-only) patch.
I won't repeat the patch summaries provided in v1:
https://lore.kernel.org/netdev/
20210129202019.
2099259-1-elder@linaro.org/
Many thanks to Willem de Bruijn for his thoughtful input.
====================
Link: https://lore.kernel.org/r/20210201172850.2221624-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Mon, 1 Feb 2021 17:28:50 +0000 (11:28 -0600)]
net: ipa: expand last transaction check
Transactions to send data for a network device can be allocated at
any time up until the point the TX queue is stopped. It is possible
for ipa_start_xmit() to be called in one context just before a
the transmit queue is stopped in another.
Update gsi_channel_trans_last() so that for TX channels the
allocated and pending transaction lists are checked--in addition
to the completed and polled lists--to determine the "last"
transaction. This means any transaction that has been allocated
before the TX queue is stopped will be allowed to complete before
we conclude the channel is quiesced.
Rework the function a bit to use a list pointer and gotos.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Mon, 1 Feb 2021 17:28:49 +0000 (11:28 -0600)]
net: ipa: don't disable interrupt on suspend
No completion interrupts will occur while an endpoint is suspended,
nor when a channel has been stopped for suspend. So there's no need
to disable the interrupt during suspend and re-enable it when
resuming. Without any interrupts occurring, there is no need to
disable/re-enable NAPI for channel suspend/resume either.
We'll only enable NAPI and the interrupt when we first start the
channel, and disable it again only when it's "really" stopped.
To accomplish this, move the enable/disable calls out of
__gsi_channel_start() and __gsi_channel_stop(), and into
gsi_channel_start() and gsi_channel_stop() instead.
Add a call to napi_synchronize() to gsi_channel_suspend(), to ensure
NAPI polling is done before moving on.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Mon, 1 Feb 2021 17:28:48 +0000 (11:28 -0600)]
net: ipa: disable interrupt and NAPI after channel stop
Disable both the I/O completion interrupt and NAPI polling on a
channel *after* we successfully stop it rather than before. This
ensures a completion occurring just before the channel is stopped
gets processed.
Enable NAPI polling and the interrupt *before* starting a channel
rather than after, to be symmetric. A stopped channel won't
generate any completion interrupts anyway.
Enable NAPI before the interrupt and disable it afterward.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Mon, 1 Feb 2021 17:28:47 +0000 (11:28 -0600)]
net: ipa: kill gsi_channel_freeze() and gsi_channel_thaw()
Open-code gsi_channel_freeze() and gsi_channel_thaw() in all callers
and get rid of these two functions. This is part of reworking the
sequence of things done during channel suspend/resume and start/stop.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Mon, 1 Feb 2021 17:28:46 +0000 (11:28 -0600)]
net: ipa: introduce __gsi_channel_start()
Create a new function that does most of the work of starting a
channel. What's different is that it takes a flag indicating
whether the channel should really be started or not. Create
another new function __gsi_channel_stop() that behaves similarly.
IPA v3.5.1 implements suspend using a special SUSPEND endpoint
setting. If the endpoint is suspended when an I/O completes on the
underlying GSI channel, a SUSPEND interrupt is generated.
Newer versions of IPA do not implement the SUSPEND endpoint mode.
Instead, endpoint suspend is implemented by simply stopping the
underlying GSI channel. In this case, a completing I/O on a
*stopped* channel causes the SUSPEND interrupt condition.
These new functions put all activity related to starting or stopping
a channel (including "thawing/freezing" the channel) in one place,
whether or not the channel is actually started or stopped.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Mon, 1 Feb 2021 17:28:45 +0000 (11:28 -0600)]
net: ipa: introduce gsi_channel_stop_retry()
Create a new helper function that encapsulates issuing a set of
channel stop commands, retrying if appropriate, with a short delay
between attempts.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
projects / platform / kernel / linux-starfive.git / log