Michael Walle [Wed, 24 Feb 2021 16:40:39 +0000 (17:40 +0100)]
net: dsa: return early if there is no master
It doesn't make sense to have DSA without a master port. Error out early
if there is no master port.
Fixes:
fc054d563bfb ("net: Introduce DSA class for Ethernet switches")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Jain [Fri, 19 Feb 2021 12:20:23 +0000 (17:50 +0530)]
board: ls1012aqds: Update MAINTAINERS
Update LS1012AQDS Board MAINTAINERS entries to
current MAINTAINERS.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Jain [Fri, 19 Feb 2021 12:20:22 +0000 (17:50 +0530)]
board: lx2160a: Update MAINTAINERS
Update LX2160AQDS BOARD MAINTAINER entry to
current MAINTAINER.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Jain [Fri, 19 Feb 2021 12:20:21 +0000 (17:50 +0530)]
board: ls1046ardb: Update MAINTAINERS
Update LS1046ARDB BOARD MAINTAINERS entries to
current MAINTAINERS.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Jain [Fri, 19 Feb 2021 12:20:20 +0000 (17:50 +0530)]
board: ls1046aqds: Update MAINTAINERS
Update LS1046AQDS BOARD MAINTAINERS entries to
current MAINTAINERS.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Jain [Fri, 19 Feb 2021 12:20:19 +0000 (17:50 +0530)]
board: ls2080ardb: Update MAINTAINERS
Update LS2080ARDB BOARD MAINTAINERS entries to
current MAINTAINERS.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Jain [Fri, 19 Feb 2021 12:20:18 +0000 (17:50 +0530)]
board: ls2080aqds: Update MAINTAINERS
Update LS2080AQDS BOARD MAINTAINERS entries to
current MAINTAINERS.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Jain [Fri, 19 Feb 2021 12:20:17 +0000 (17:50 +0530)]
board: ls1088a: Update MAINTAINERS
Update LS1088ARDB, LS1088AQDS BOARD MAINTAINERS
entries to current MAINTAINERS.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Jain [Fri, 19 Feb 2021 12:20:16 +0000 (17:50 +0530)]
board: ls1043ardb: Update MAINTAINERS
Update LS1043ARDB BOARD MAINTAINERS entries
to current MAINTAINERS.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Jain [Fri, 19 Feb 2021 12:20:15 +0000 (17:50 +0530)]
board: ls1028a: Update MAINTAINERS
Update LS1028AQDS, LS10128ARDB board MAINTAINERS
entries to current MAINTAINERS.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Jain [Fri, 19 Feb 2021 12:20:14 +0000 (17:50 +0530)]
board: ls1021atwr: Update MAINTAINERS
Update LS1021ATWR BOARD MAINTAINERS entries to
current MAINTAINERS.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Jain [Fri, 19 Feb 2021 12:20:13 +0000 (17:50 +0530)]
board: ls1021aiot: Update MAINTAINERS
Update LS1021AIOT BOARD MAINTAINERS entries to
current MAINTAINERS.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Jain [Fri, 19 Feb 2021 12:20:12 +0000 (17:50 +0530)]
board: ls1012ardb: Update MAINTAINERS
Update LS1012ARDB BOARD MAINTAINERS entries
to current MAINTAINERS.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Jain [Fri, 19 Feb 2021 12:20:11 +0000 (17:50 +0530)]
board: ls1012afrdm: Update MAINTAINERS
Update LS1012AFRWY BOARD MAINTAINER entry
to current MAINTAINER.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Jain [Fri, 19 Feb 2021 12:20:10 +0000 (17:50 +0530)]
board: corenet_ds: MAINTAINERS: Remove redundant entries
Remove MAINTAINERS entries for
P3041DS_NAND_SECURE_BOOT_defconfig
and P5040DS_NAND_SECURE_BOOT_defconfig
as these configs support have been removed.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Rajesh Bhagat [Mon, 15 Feb 2021 08:46:14 +0000 (09:46 +0100)]
configs: fsl: move via specific defines to Kconfig
Moves below via specific defines to Kconfig:
CONFIG_FSL_VIA
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Rajesh Bhagat [Thu, 11 Feb 2021 12:28:49 +0000 (13:28 +0100)]
configs: fsl: move bootrom specific defines to Kconfig
Moves below bootrom specific defines to Kconfig:
CONFIG_SYS_FSL_BOOTROM_BASE
CONFIG_SYS_FSL_BOOTROM_SIZE
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Stephen Carlson [Mon, 8 Feb 2021 10:11:29 +0000 (11:11 +0100)]
arm: fsl: common: Improve NXP VID driver PMBus support
This patch adds support for more PMBus compatible devices to the NXP
drivers for its QorIQ family devices. At runtime, the voltage regulator is
queried over I2C, and the required voltage multiplier determined. This
change supports the DIRECT and LINEAR PMBus voltage reporting modes.
Previously, the driver only supported a few specific devices such as the
IR36021 and LTC3882, so this change allows the QorIQ series to be used
with a much larger variety of core voltage regulator devices.
checkpatch warning "Use if (IS_DEFINED (...))" was ignored to maintain
consistency with the existing code.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Tested-by: Wasim Khan <wasim.khan@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Tom Rini [Thu, 4 Mar 2021 21:59:00 +0000 (16:59 -0500)]
Azure/GitLab: Use buildman -T0 for binman, etc, test
There are times where buildman seems to get stuck in this job when in
CI. Forcing single-threaded here allows us to complete and move on.
Signed-off-by: Tom Rini <trini@konsulko.com>
Simon Glass [Sun, 31 Jan 2021 05:17:46 +0000 (22:17 -0700)]
buildman: Support single-threaded operation
At present even if only a single thread is in use, buildman still uses
threading.
For some debugging it is helpful to do everything in the main process.
Allow -T0 to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Pali Rohár [Wed, 24 Feb 2021 00:27:29 +0000 (01:27 +0100)]
Nokia RX-51: Enable CONFIG_CMD_BOOTD
CONFIG_CMD_BOOTD provides 'boot' command which is required in more scripts.
Signed-off-by: Pali Rohár <pali@kernel.org>
Pali Rohár [Wed, 3 Mar 2021 09:52:36 +0000 (10:52 +0100)]
fs/squashfs: Fix compilation error
Commit
401d1c4f5d2d29c4bc4beaec95402ca23eb63295 ("common: Drop
asm/global_data.h from common header") broke compilation of squashfs
filesystem when CONFIG_CMD_SQUASHFS=y is enabled.
Compilation is failing on error:
aarch64-linux-gnu-ld.bfd: u-boot/fs/squashfs/sqfs_inode.c:121: undefined reference to `le32_to_cpu'
Fixes:
401d1c4f5d2d29c4bc4beaec95402ca23eb63295 ("common: Drop asm/global_data.h from common header")
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 4 Mar 2021 03:53:53 +0000 (22:53 -0500)]
Merge tag 'dm-pull-3mar21' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
dm: Fix an obscure bug with empty of-platdata
Fixes for ns16550 base address and frequency-reading
Other minor fixes
Bin Meng [Wed, 3 Feb 2021 14:42:25 +0000 (22:42 +0800)]
serial: ns16550: Handle zero <clock-frequency> value
A working device tree node of ns16550 should never be populated
with value zero for the <clock-frequency> property. Unfortunately
this is the case for the QEMU ppce500 target.
Let's try to assign plat->clock to CONFIG_SYS_NS16550_CLK as the
last resort to handle such case.
This commit should be reverted when:
- The following QEMU patch [1] is merged, and
- U-Boot CI has upgraded its QEMU version that contains the fix
[1] http://patchwork.ozlabs.org/project/qemu-devel/patch/
1612362288-22216-2-git-send-email-bmeng.cn@gmail.com/
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Bin Meng [Wed, 3 Feb 2021 13:22:40 +0000 (21:22 +0800)]
serial: ns16550: Correct the base address type
Currently ns16550_serial_assign_base() treats the argument 'base'
with type `ulong`. This is incorrect because the base address was
obtained from device tree with type `fdt_addr_t` that can represent
a physical address larger than 32-bit in a 32-bit system.
Fixes:
9e6ce62190b7 ("serial: ns16550: Fix ordering of getting base address")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Bin Meng [Wed, 3 Feb 2021 13:20:03 +0000 (21:20 +0800)]
dts: Fix OF_LIVE dependency
lib/of_live.c references the following 2 ofnode APIs:
of_alias_scan() and of_get_property().
These APIs get built only when DM is on. Fix the dependency then.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Bin Meng [Wed, 3 Feb 2021 13:20:02 +0000 (21:20 +0800)]
lib: Fix BINMAN_FDT dependency
lib/binman.c references the following 3 ofnode APIs:
ofnode_first_subnode(), ofnode_path() and ofnode_read_bool().
These APIs get built only when DM is on. Fix the dependency then.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Heinrich Schuchardt [Tue, 2 Feb 2021 23:21:56 +0000 (00:21 +0100)]
sandbox: host bind must close file descriptor
Each invocation of the 'host bind' command with a file name argument opens
a file descriptor. The next invocation of the 'host bind' command destroys
the block device but the file descriptor remains open. The same holds true
for the 'unbind blk' command.
Close the file descriptor when unbinding the host block device.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Bernhard Kirchen [Fri, 29 Jan 2021 14:10:08 +0000 (15:10 +0100)]
fix patman --limit-cc option
patman's --limit-cc option parses its argument to an integer and uses
that to trim the list of CC recipients to a particular maximum. but that
only works if the cc variable is a list, which it is not.
Signed-off-by: Bernhard Kirchen <bernhard.kirchen@mbconnectline.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 3 Feb 2021 13:00:49 +0000 (06:00 -0700)]
bootstage: Fix dependency for BOOTSTAGE_RECORD_COUNT
At present these three Kconfigs exist even when bootstage is not enabled.
This is not necessary since bootstage.c is only built if BOOTSTAGE is
enabled.
Make them conditional. Also fix up the overflow message to mention TPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Thu, 4 Feb 2021 04:29:44 +0000 (21:29 -0700)]
dm: core: Add DM_DEVICE_REMOVE condition to all exit paths
At present device_bind() does some unnecessary work if a device fails to
bind in SPL. Add the missing conditions.
Also fix a style nit in the same function while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Thu, 4 Feb 2021 04:29:43 +0000 (21:29 -0700)]
dm: core: Fix allocation of empty of-platdata
With of-platdata we always have a dtv struct that holds the platform data
provided by the driver_info record. However, this struct can be empty if
there are no actual devicetree properties provided.
The upshot of empty platform data is that it will end up as a zero-size
member in the BSS section, which is fine. But if the driver specifies
plat_auto then it expects the correct amount of space to be allocated.
At present this does not happen, since device_bind() assumes that the
platform-data size will always be >0. As a result we end up not
allocating the space and just use the BSS region, overwriting whatever
other contents are present.
Fix this by removing the condition that platform data be non-empty, always
allocating space if requested.
This fixes a strange bug that has been lurking since of-platdata was
implemented. It has likely never been noticed since devices normally have
at least some devicetree properties, BSS is seldom used on SPL, the dtv
structs are normally at the end of bss and the overwriting only happens
if a driver changes its platform data.
It was discovered using sandbox_spl, which exercises more features than
a normal board might, and the critical global_data variable 'gd' happened
to be at the end of BSS.
Fixes:
9fa28190091 ("dm: core: Expand platdata for of-platdata devices")
Signed-off-by: Simon Glass <sjg@chromium.org>
Tom Rini [Wed, 3 Mar 2021 15:10:34 +0000 (10:10 -0500)]
Merge tag 'u-boot-imx-
20210303' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
i.MX for 2021.04
----------------
- new boards:
- i.MX8MN Beacon EmbeddedWorks (2GB)
- Gateworks Venice imx8mm
- convert to DM:
- imx53-qsb, mx53loco, mx51evk, mx23-evk
- Fixes :
- Network : FEC ethernet quirks
- DH dh-imx6
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/6597
Tim Harvey [Tue, 2 Mar 2021 22:00:21 +0000 (14:00 -0800)]
board: gateworks: imx8mm: Add Gateworks Venice board support
Add initial support for Gateworks Venice product family based on the
i.MX 8M Mini SoC
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Tue, 2 Mar 2021 22:00:20 +0000 (14:00 -0800)]
arm: dts: imx8mm: add Gateworks i.MX8 Mini Dev kits
Add Gateworks i.MX 8M Mini Development kits from Linux-5.12-rc1
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tom Rini [Wed, 3 Mar 2021 12:54:55 +0000 (07:54 -0500)]
Merge https://source.denx.de/u-boot/custodians/u-boot-usb
- Kconfig dependency fix for USB_KEYBOARD
- musb gadget fixes / enhancements
Heinrich Schuchardt [Sun, 28 Feb 2021 11:50:49 +0000 (12:50 +0100)]
usb: USB keyboard requires DM_KEYBOARD
If CONFIG_DM_USB=y, the USB keyboard only works if CONFIG_DM_KEYBOARD=y.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Pali Rohár [Sat, 20 Feb 2021 10:50:15 +0000 (11:50 +0100)]
Nokia RX-51: Enable usbtty serial console by default
Now when usbtty serial console is fixed in U-Boot enable CONFIG_USB_TTY for
Nokia RX-51 board by default.
Fix also USB product id as U-Boot ignores CONFIG_USBD_PRODUCTID macro and
include U-Boot string into USB product name to indicate usage of U-Boot.
CONFIG_CONSOLE_MUX is already used and U-Boot console is available for
all in/out devices. Therefore there is no need to have separate commands
'run sercon', 'run usbcon' and 'run vgacon', so remove them.
As space for U-Boot is limited to 256kB, enable CONFIG_OPTIMIZE_INLINING
and disable some other unused options so CONFIG_USB_TTY can be enabled.
Nokia RX-51 does not have easily accessible UART serial console so the only
option for easy debugging is to use device's keyboard+screen or this usbtty
serial console over USB.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Pali Rohár [Sun, 7 Feb 2021 13:50:15 +0000 (14:50 +0100)]
Nokia RX-51: Move content of rx51.h to rx51.c
After removal of MUX configuration there is no need to have extra rx51.h.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Pali Rohár [Sun, 7 Feb 2021 13:50:14 +0000 (14:50 +0100)]
Nokia RX-51: Remove function set_muxconf_regs()
This function is not used and was never called.
This board contains '#define CONFIG_SKIP_LOWLEVEL_INIT' because X-Loader
set everything up, including MUX configuration.
Also this MUX configuration is incorrect and does not match hardware.
So remove this dead, unused and broken code.
This change will decrease size of U-Boot binary.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Pali Rohár [Sun, 7 Feb 2021 13:50:13 +0000 (14:50 +0100)]
arm: omap3: Compile s_init() function only when it is used
Function s_init() is called only from lowlevel_init(). So compile it only
when function lowlevel_init() is compiled.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Pali Rohár [Sun, 7 Feb 2021 13:50:12 +0000 (14:50 +0100)]
arm: omap3: Compile lowlevel_init() function only when it is used
Function lowlevel_init() is called only from cpu_init_crit() and this
function is wrapped into #if .. #endif section. So compile also
lowlevel_init() function under same #if condition.
Function cpy_clk_code() uses lowlevel_init symbol to get address where
go_to_speed code ends. As this symbol is not available anymore when
compiling with CONFIG_SKIP_LOWLEVEL_INIT, defines a new label
go_to_speed_end at the place where go_to_speed code ends.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Pali Rohár [Sun, 7 Feb 2021 13:50:11 +0000 (14:50 +0100)]
usb: gadget: Use dbg_ep0() macro instead of serial_printf()
All debug messages from ep0.c except a few are printed by dbg_ep0() macro.
So for remaining few exceptions use also dbg_ep0() instead of serial_printf().
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Pali Rohár [Sun, 7 Feb 2021 13:50:10 +0000 (14:50 +0100)]
usb: musb: Ensure that we set musb dynamic FIFO buffer for every endpoint
If we do not set FIFO buffer address and size for some endpoint which is in
use then default programmed address 0x0 would be used which is in conflict
with address of FIFO buffer for endpoint 0. Moreover address of FIFO buffer
for endpoint 0 cannot be programmed, it is fixed to 0x0. Sharing address
space between more endpoints cause data loss and unexpected errors.
This patch is fixing transmission of characters over usbtty serial console
and allows using of usbtty for debugging purposes on Nokia N900.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Pali Rohár [Sun, 7 Feb 2021 13:50:09 +0000 (14:50 +0100)]
usb: musb: Fix handling interrupts for EP0 and SET ADDRESS commmand
Interrupt for EP0 is indicated in intrtx register via first bit. This bit
is set for both RX and TX despite register has only TX in its name. First
bit in intrrx register is reserved, not used and never set.
So remove calling musb_peri_ep0() function at every iteration of udc_irq()
and musb_peri_rx() and call it only from musb_peri_tx() when correct
interrupt bit in initrtx it set.
Address from SET ADDRESS command must be set to faddr register only after
acknowledging SERV_RXPKTRDY followed by received EP0 interrupt. So prior
calling musb_peri_ep0_set_address() check for EP0 interrupt instead of
(incorrect) MUSB_INTR_SOF interrupt.
This patch fixes issue that host (computer) cannot register U-Boot USB
device and is failing with errors:
usb 1-1: new full-speed USB device number 86 using xhci_hcd
usb 1-1: Device not responding to setup address.
usb 1-1: Device not responding to setup address.
usb 1-1: device not accepting address 86, error -71
U-Boot was writing address to faddr register too early and did not wait for
correct interrupt after which should update address.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Pali Rohár [Sun, 7 Feb 2021 13:50:08 +0000 (14:50 +0100)]
usb: musb: Fix receiving of bigger buffers
If musb_peri_rx_ep() was called to process received HW buffer but U-Boot
cannot read it yet (e.g. because U-Boot SW buffer is full) then interrupt
was marked as processed also when HW buffer stayed unprocessed.
U-Boot tried to process this buffer again when it received interrupt again,
but it can receive it only when sender (host) sends a new data. As sender
(host) is not going to send a new data until U-Boot process current data
this issue caused a deadlock in case sender (host) is emitting data faster
than U-Boot can process it.
Reading musb intrrx register automatically clears this register and marks
interrupt as processed. So to prevent marking interrupt in U-Boot as
processed, adds a new variable pending_intrrx which would contain
unprocessed bits of intrrx register.
For a second step, every time when musb_peri_rx_ep() is called and there
are waiting data to be processed (signaled by MUSB_RXCSR_RXPKTRDY) either
acknowledge sender (via musb_peri_rx_ack()) that whole HW buffer was
processed or set corresponding bit in pending_intrrx that HW buffer was not
fully processed yet and next iteration is required after U-Boot allocates
space for reading HW buffer.
This patch fixes receiving large usb buffers, e.g. file transfer via Kermit
protocol implemented by 'loadb' U-Boot command over usbtty serial console.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Pali Rohár [Sun, 7 Feb 2021 13:50:07 +0000 (14:50 +0100)]
usb: musb: Fix transmission of bigger buffers
If udc_endpoint_write() was called with bigger payload which does not fit
into one USB packet it is needed to transmit payload in more USB packets.
First packet is transmitted by udc_endpoint_write() call itself and other
packets are put into waiting queue.
Implement function musb_peri_tx() which checks if endpoints are ready for
transmit and continue transmission of waiting queue.
This patch fixes sending big output from printenv command over usbtty
serial console.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>>
Pali Rohár [Sun, 7 Feb 2021 13:50:06 +0000 (14:50 +0100)]
usb: musb: Read value of PERI_RXCSR to 16bit variable
PERI_RXCSR is 16bit register so store its value into 16bit local variable.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Pali Rohár [Sun, 7 Feb 2021 13:50:05 +0000 (14:50 +0100)]
usb: musb: Fix configuring FIFO for endpoints
This patch fixes configuring FIFOs for one-directional endpoints which have
only one queue (either RX or TX, but noth both).
Size of FIFO buffer is 2^(idx+3) bytes and starting address is 2^(addr+3).
Moreover first 64 bytes are reserved for EP0.
Without this patch if FIFO size specified by caller was zero then idx was
incorrectly calculated (expr. ffs(0)-1) and size overflowed in fifosz
register. This register uses has only 4 bits for FIFO size. Moreover
specifying zero buffer size is not possible (with idx=0 is minimal buffer
size 8 bytes).
So even for one-directional endpoints we need to correctly specify both
(RX and TX) FIFO buffer sizes and its addresses.
This patch is fixing calculation of start address and buffer size to
minimal value and ensures that it would not overlap with buffer reserved
for EP0.
This issue caused loose of packets on USB bus in both directions and
basically usbtty was unusable.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Pali Rohár [Sun, 7 Feb 2021 13:50:04 +0000 (14:50 +0100)]
usb: musb: Always clear the data toggle bit when configuring ep
Without this patch clearing was done only when U-Boot was compiled with
MUSB Host Controller. But clearing of data toggle bit is needed also for
MUSB Device Controller otherwise Device Controller does not work correctly.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Pali Rohár [Sun, 7 Feb 2021 13:50:03 +0000 (14:50 +0100)]
usb: musb: Fix compilation of gadget code
musb udc code depends on usb gadget code provided by CONFIG_USB_DEVICE as
defined in drivers/usb/gadget/Makefile. But this Makefile is not included
into U-Boot build when CONFIG_USB_GADGET is not set. As CONFIG_USB_DEVICE
cannot be enabled together with CONFIG_USB_GADGET it means that dependency
for musb udc code is not compiled during build. Fix it by including
drivers/usb/gadget dependency also when CONFIG_USB_DEVICE is set.
This patch fixes compile errors:
arm-linux-gnueabi-ld.bfd: drivers/usb/musb/built-in.o: in function `musb_peri_ep0_rx':
u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `ep0_recv_setup'
arm-linux-gnueabi-ld.bfd: drivers/usb/musb/built-in.o: in function `musb_peri_ep0_idle':
u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `ep0_recv_setup'
arm-linux-gnueabi-ld.bfd: drivers/usb/musb/built-in.o: in function `musb_peri_ep0_zero_data_request':
u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_device_event_irq'
arm-linux-gnueabi-ld.bfd: drivers/usb/musb/built-in.o: in function `musb_peri_ep0_idle':
u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `ep0_recv_setup'
arm-linux-gnueabi-ld.bfd: drivers/usb/musb/built-in.o: in function `musb_peri_ep0_rx':
u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_rcv_complete'
arm-linux-gnueabi-ld.bfd: drivers/usb/musb/built-in.o: in function `musb_peri_rx_ep':
u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_rcv_complete'
arm-linux-gnueabi-ld.bfd: drivers/usb/musb/built-in.o: in function `udc_endpoint_write':
u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_tx_complete'
arm-linux-gnueabi-ld.bfd: drivers/usb/musb/built-in.o: in function `udc_irq':
u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_device_event_irq'
arm-linux-gnueabi-ld.bfd: u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_device_event_irq'
arm-linux-gnueabi-ld.bfd: u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_device_event_irq'
arm-linux-gnueabi-ld.bfd: u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_device_event_irq'
arm-linux-gnueabi-ld.bfd: u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_device_event_irq'
arm-linux-gnueabi-ld.bfd: drivers/usb/musb/built-in.o:u-boot/drivers/usb/musb/musb_udc.c: more undefined references to `usbd_device_event_irq' follow
arm-linux-gnueabi-ld.bfd: drivers/usb/musb/built-in.o: in function `udc_setup_ep':
u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_alloc_urb'
arm-linux-gnueabi-ld.bfd: drivers/usb/musb/built-in.o: in function `udc_startup_events':
u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_device_event_irq'
arm-linux-gnueabi-ld.bfd: u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_device_event_irq'
arm-linux-gnueabi-ld.bfd: u-boot/drivers/usb/musb/musb_udc.c: undefined reference to `usbd_device_event_irq'
make: *** [Makefile:1762: u-boot] Error 1
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Pali Rohár [Sun, 7 Feb 2021 13:50:02 +0000 (14:50 +0100)]
serial: usbtty: Send urb data in correct order
Function next_urb() selects the last urb data buffer from linked list to
which next data from usbtty's puts function should be appended.
But to check if TX data still exists it is needed to look at the first urb
data buffer from linked list. So check for endpoint->tx_urb (first from the
linked list) instead of current_urb (the last from the linked list).
Successful call to udc_endpoint_write() may invalidate active urb and
allocate new urb in queue which invalidates pointer returned by next_urb()
function.
So call next_urb() prior putting data into urb buffer and call it every
time after using udc_endpoint_write() function to prevent sending data from
usbtty's puts function in incorrect order.
This patch fixes issue that usbtty code does not transmit data when they
are waiting in the tx queue.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Pali Rohár [Sun, 7 Feb 2021 13:50:01 +0000 (14:50 +0100)]
serial: usbtty: Fix puts function
This function has incorrect implementation of prepending CR prior LF.
Without this patch it prepended CR prior whole string which is going to be
written and let LF without leading CR. Fix this issue by inserting CR at
correct place to make output on usbtty serial console more readable.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Tom Rini [Tue, 2 Mar 2021 21:46:16 +0000 (16:46 -0500)]
Merge tag 'rpi-next-2021.04.2' of https://source.denx.de/u-boot/custodians/u-boot-raspberrypi
- Disable Grub workaround for RPi2
- enable HS200 mode for iproc sdhci
- add armv7 support for iproc_rng200
Tom Rini [Tue, 2 Mar 2021 14:36:23 +0000 (09:36 -0500)]
configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
Matthias Brugger [Fri, 26 Feb 2021 10:48:01 +0000 (11:48 +0100)]
configs: rpi4_32: Enable iProc RNG200
Enable the RNG driver for RPi4 with 32 bit.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Matthias Brugger [Fri, 26 Feb 2021 10:48:00 +0000 (11:48 +0100)]
rng: iproc_rng200: Enable support for RPi4 armv7
On the RPi4 armv7 build we have the situationt that we use physical
addresses of 64 bit, while the virtual addresses are 32 bit.
Remap the base address in this scenario via map_physmem().
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Matthias Brugger [Fri, 26 Feb 2021 10:23:16 +0000 (11:23 +0100)]
MAINTAINERS: Update info for Raspberry Pi
Add RPi config files and custodian repository.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Bharat Gooty [Fri, 26 Feb 2021 06:15:13 +0000 (11:45 +0530)]
drivers: mmc: iproc_sdhci: enable HS200 mode
Add tuning functionality which is needed for HS200 mode.
For HS200, program the correct needed 1.8 voltage
Signed-off-by: Bharat Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Matthias Brugger [Tue, 16 Feb 2021 19:54:08 +0000 (20:54 +0100)]
configs: RPi2: Disable EFI Grub workaround
The EFI Grub workaround isn't needed with Grub version 2.04 or higher.
This version was published over a year ago, so disable the workaround
to reduce boot time.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Tom Rini [Tue, 2 Mar 2021 03:46:41 +0000 (22:46 -0500)]
Prepare v2021.04-rc3
Signed-off-by: Tom Rini <trini@konsulko.com>
Marek Vasut [Mon, 1 Mar 2021 15:41:28 +0000 (16:41 +0100)]
ARM: imx: Include u-boot.img in u-boot-with-spl.imx if OF_SEPARATE=y
The u-boot-with-spl.imx is a concatenation of SPL and u-boot.uim.
The u-boot.uim is u-boot.bin wrapped in uImage. In case OF_SEPARATE
is enabled, the u-boot.bin does not contain control DT for U-Boot,
and so u-boot.uim does not contain the DT, and so u-boot-with-spl.imx
does not contain the DT, and a system where u-boot-with-spl.imx is
written to offset 1024B to the start of storage no longer boots, as
it is missing DT.
In case OF_SEPARATE is enabled, u-boot.img contains both u-boot.bin
and the necessary DTs. Therefore, use u-boot.img instead of u-boot.uim
to generate u-boot-with-spl.imx when OF_SEPARATE is enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Heinrich Schuchardt [Mon, 4 Jan 2021 07:02:55 +0000 (08:02 +0100)]
log: convert pr_*() to logging
In drivers we use a family of printing functions including pr_err() and
pr_cont(). CONFIG_LOGLEVEL is used to control which of these lead to output
via printf().
Our logging functions allow finer grained control of output. So replace
printf() by the matching logging functions. The usage of CONFIG_LOGLEVEL
remains unchanged.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Marek Behún [Tue, 9 Feb 2021 17:33:37 +0000 (18:33 +0100)]
fs: btrfs: do not fail when offset of a ROOT_ITEM is not -1
When the btrfs_read_fs_root() function is searching a ROOT_ITEM with
location key offset other than -1, it currently fails via BUG_ON.
The offset can have other value than -1, though. This can happen for
example if a subvolume is renamed:
$ btrfs subvolume create X && sync
Create subvolume './X'
$ btrfs inspect-internal dump-tree /dev/root | grep -B 2 'name: X$
location key (270 ROOT_ITEM
18446744073709551615) type DIR
transid 283 data_len 0 name_len 1
name: X
$ mv X Y && sync
$ btrfs inspect-internal dump-tree /dev/root | grep -B 2 'name: Y$
location key (270 ROOT_ITEM 0) type DIR
transid 285 data_len 0 name_len 1
name: Y
As can be seen the offset changed from -1ULL to 0.
Do not fail in this case.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: David Sterba <dsterba@suse.com>
Cc: Qu Wenruo <wqu@suse.com>
Cc: Tom Rini <trini@konsulko.com>
Marek Vasut [Sat, 27 Feb 2021 13:59:00 +0000 (14:59 +0100)]
ARM: imx: Do not hard-code MX8M MMU table DRAM entry offset
Instead of hard-coding the offset of DRAM entries in MMU table all over
the code, auto-detect the offset. This removes error-prone code which
would break e.g. in case the MMU table is modified.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Fabio Estevam [Mon, 22 Feb 2021 17:40:47 +0000 (14:40 -0300)]
ARM: dts: imx8mq-evk: Remove u-boot,off-on-delay-us property
Commit
247bbeb74c18 ("ARM: dts: imx8m: increase off-on delay on the SD Vcc
regulator") caused the imx8mq-evk board to not be able to store the
environment variables in the SD card.
Remove the u-boot,off-on-delay-us property to fix the regression.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Fabio Estevam [Mon, 22 Feb 2021 16:16:43 +0000 (13:16 -0300)]
tools: imx8mimage: Restore the original __ALIGN_MASK() macro
Since commit
c738adb8dbbf ("tool: Move ALIGN_MASK to header as common MACRO")
the i.MX8MQ EVK board no longer boots.
The reason is that imx8mimage.c used a custom __ALIGN_MASK() macro, so
restore the original macro to fix the boot and rename it accordingly.
Reported-by: Lukas Rusak <lorusak@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Ye Li <ye.li@nxp.com>
Ye Li [Fri, 19 Feb 2021 06:33:48 +0000 (22:33 -0800)]
arm: dts: imx8mp-evk: Add FEC PHY reset timing
Add phy-reset-duration and phy-reset-post-delay to FEC node for PHY
reset, otherwise the PHY does not work correctly.
Signed-off-by: Ye Li <ye.li@nxp.com>
Adam Ford [Tue, 16 Feb 2021 14:19:52 +0000 (08:19 -0600)]
imx: Add 2GB lpddr support for i.MX8MN Beacon EmbeddedWorks devkit.
There is a second lpddr configuration with 2GB of RAM, but this requires
different RAM timings, so in addition to adding the timing file, a
separate defconfig is necessary.
Signed-off-by: Adam Ford <aford173@gmail.com>
Peter Bergin [Sun, 14 Feb 2021 19:19:22 +0000 (20:19 +0100)]
doc: board: freescale: imx8mp_evk: update to newer versions and change ATF_LOAD_ADDR
Update imx-atf and firmware-imx to latest released versions.
Update address of ATF_LOAD_ADDR that has changed to 0x970000 in imx-atf
commit
48733cb4e773a7584ced601de9d717efa3d73815.
Add 'O=' to make and build in separate directory as one issue has been noticed
where it was trouble building directly inside u-boot source dir. Restructure the workflow
and copy binaries after defconfig to ensure that build directory is created.
Signed-off-by: Peter Bergin <peter@berginkonsult.se>
Cc: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Reviewed-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Marek Vasut [Thu, 25 Feb 2021 21:02:26 +0000 (22:02 +0100)]
ARM: imx: Add missing FEC ethernet quirk for MX8M
The MX8M also contains a gigabit MAC, so define FEC_QUIRK_ENET_MAC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Ye Li [Sun, 21 Feb 2021 02:25:45 +0000 (18:25 -0800)]
mx6sabre: Fix boot failure
CONFIG_SPL_LEGACY_IMAGE_SUPPORT is necessary for mx6sabresd and
mx6sabreauto, because u-boot is packed as legacy image not FIT.
However, this config is not set when CONFIG_SPL_LOAD_FIT is enabled.
Must enable it explicitly, otherwise will fail to boot like below.
U-Boot SPL 2021.04-rc2 (Feb 20 2021 - 16:43:04 -0800)
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
Signed-off-by: Ye Li <ye.li@nxp.com>
Haibo Chen [Fri, 19 Feb 2021 19:25:32 +0000 (11:25 -0800)]
mmc: fsl_esdhc_imx: fix the DTOCV to 0xE
On imx6Q/imx6DL, we find if config the DTOCV to 0~3, it will impact
cmd6 behavior, after cmd6 get transfer complete interrupt, the data0
line will keep low over 5 seconds. This should be a IC bug on imx6Q/DL.
For other platforms, do not has this issue.
To fix this issue, fix the DTOCV to 0xE, the max setting, this also align
with Linux configuration.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Fabio Estevam [Thu, 18 Feb 2021 23:32:30 +0000 (20:32 -0300)]
mx23evk: Add myself as maintainer
I would like to help supporting this board, so add myself
as a maintainer.
Now that the board has been converted to DM, also add
its devicetree in the MAINTAINERS files entry.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Fabio Estevam [Thu, 18 Feb 2021 23:32:29 +0000 (20:32 -0300)]
mx23evk: Convert to driver model
Make the conversion to driver model as it is mandatory.
Successfully tested booting Linux from the SD card.
Dropped splash screen support as this needs to be properly
converted to DM and tested.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Fabio Estevam [Thu, 18 Feb 2021 23:32:28 +0000 (20:32 -0300)]
mx23-evk: Import devicetree file from Linux
Import the imx23-evk devicetree files from Linux kernel
version 5.11.
This is in preparation for converting the mx23evk_defconfig
target to driver model.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Fabio Estevam [Mon, 15 Feb 2021 11:58:18 +0000 (08:58 -0300)]
mx51evk: Add myself as maintainer
I would like to help supporting this board, so add myself
as a maintainer.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Fabio Estevam [Mon, 15 Feb 2021 11:58:17 +0000 (08:58 -0300)]
mx51evk: Convert to driver model
Make the conversion to driver model as it is mandatory.
Tested booting the Linux kernel from the SD card.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Fabio Estevam [Mon, 15 Feb 2021 11:58:16 +0000 (08:58 -0300)]
imx51-babbage: Import devicetree files from Linux
Import the imx51-babbage devicetree files from Linux kernel
version 5.11-rc7.
This is in preparation for converting the mx51evk_defconfig
target to driver model.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Fabio Estevam [Mon, 15 Feb 2021 11:58:15 +0000 (08:58 -0300)]
mmc: fsl_esdhc_imx: Add a compatible for i.MX51
Add a compatible for i.MX51 so that i.MX51 can use this driver
via driver model.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Fabio Estevam [Sun, 14 Feb 2021 01:49:54 +0000 (22:49 -0300)]
mx53loco: Add myself as maintainer
I would like to help supporting this board, so add myself
as a maintainer.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Fabio Estevam [Sun, 14 Feb 2021 01:49:53 +0000 (22:49 -0300)]
ARM: dts: imx53-qsb: Describe the esdhc1 card detect pin
The micro SD card slot uses GPIO3_13 as card detect pin, so describe
it in the devicetree.
This was noticed when converting imx53-qsb board to driver model
in U-Boot as the micro SD card was not getting detected.
After this change it is possible to load the dtb and zImage
from the SD card and boot Linux.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Fabio Estevam [Sun, 14 Feb 2021 01:49:52 +0000 (22:49 -0300)]
mx53loco: Convert to driver model
Make the conversion to driver model as it is mandatory.
Remove the SATA support for now as the i.MX53 support has not
been added yet.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Fabio Estevam [Sun, 14 Feb 2021 01:49:51 +0000 (22:49 -0300)]
imx53-qsb: Import devicetree files from Linux
Import the imx53-qsb devicetree files from Linux kernel
version 5.11-rc7.
This is in preparation for converting the mx53loco_defconfig
target to driver model.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Oleksandr Suvorov [Tue, 9 Feb 2021 08:38:13 +0000 (10:38 +0200)]
board: toradex: move RGMII delays to PHY side
The RGMII link delays can be set on either MAC or PHY side. Set the
rgmii-id PHY mode for FEC and remove FEC_ENET_ENABLE_.XC_DELAY
setting, so that these definitions aren't used anymore throughout
the U-Boot.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Oleksandr Suvorov [Tue, 9 Feb 2021 08:38:12 +0000 (10:38 +0200)]
ARM: imx8: Add missing FEC ENET quirk for i.MX8/i.MX8X
Both NXP SoCs i.MX8 and i.MX8X have ENET gigabit MAC.
Define FEC_QUIRK_ENET_MAC for the imx8 platform and remove this
definition from configs of boards, based on MX8/MX8X.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Frieder Schrempf [Sat, 6 Feb 2021 00:11:06 +0000 (16:11 -0800)]
Respect that some compression algos can be enabled separately for SPL
Some compression algorithms currently can be enabled for SPL and
U-Boot proper separately. Therefore take into account USE_HOSTCC
is well as CONFIG_IS_ENABLED() in these cases to prevent compiling these
functions in case of a host tool build.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Sat, 6 Feb 2021 00:11:05 +0000 (16:11 -0800)]
thermal: imx_tmu: enable monitoring and default alert/critical
Set default critical/alert temperature and enabling monoitoring.
Without calling imx_tmu_enable_msite() monitoring will not be enabled
and read_temperature will return 0. Additionally without setting alert
temperature will cause imx_tmu_get_temp() to spin indefiniately thinking
the system needs to cool.
This resolves the board spinning endlessly when enabling IMX_TMU in the
SPL.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Sean Anderson [Thu, 4 Feb 2021 21:44:22 +0000 (16:44 -0500)]
ARM: mx6: Add function to set serial#
The serial number OTP is similar to the imx7 version, except that the
register names are different. This also sets serial# directly, instead of
providing board_get_serial.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Marek Vasut [Thu, 4 Feb 2021 18:00:32 +0000 (19:00 +0100)]
ARM: imx6: mx6sabre-common: Search for boot components in /boot too
Some root filesystem configurations do not have separate /boot partition,
but rather place kernel, DT, scripts into /boot directory. Search the /boot
directory for these boot components in case they are not found in /, which
is the old behavior.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Marek Vasut [Thu, 4 Feb 2021 18:00:31 +0000 (19:00 +0100)]
ARM: imx6: mx6sabre-common: Replace fatload with FS_GENERIC load
Replace filesystem specific fatload command with a filesystem agnostic
load command, so the board can boot from e.g. ext4 too.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tom Rini [Wed, 24 Feb 2021 22:05:04 +0000 (17:05 -0500)]
uboot-test-hooks: Switch to our GitLab instance
As Stephen is no longer actively maintaining the uboot-test-hooks
repository, switch to using the instance on our GitLab.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Heinrich Schuchardt [Wed, 24 Feb 2021 12:19:04 +0000 (13:19 +0100)]
Correct U-Boot upstream repository
The U-Boot source moves to https://source.denx.de/u-boot/u-boot.git
effective 2021-02-28.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Marek Vasut [Thu, 4 Feb 2021 00:17:02 +0000 (01:17 +0100)]
ARM: imx6: dh-imx6: Drop the SF hunk in config
There is now CONFIG_SPL_DM_SPI{,_FLASH}, however keeping
CONFIG_DM_SPI{,_FLASH} enabled in SPL seems to grow the SPL
by a couple of bytes:
text data bss dec hex filename
- 34069 1568 96 35733 8b95 spl/u-boot-spl
+ 34075 1568 96 35739 8b9b spl/u-boot-spl
In either case, the binary is bootable, so remove the part
in board config.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Marek Vasut [Wed, 3 Feb 2021 22:22:17 +0000 (23:22 +0100)]
ARM: imx6: dh-imx6: Enable support for applying DTO
Enable DTO support to make it possible to boot fitImage with DTOs
embedded in them.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Wed, 3 Feb 2021 21:36:33 +0000 (22:36 +0100)]
ARM: imx: Revert "dh_imx6: Switch to full DM-aware"
This reverts commit
03a673cf49e ("dh_imx6: Switch to full DM-aware").
According to discussion [1], the patch is known to break the dh_imx6
board, however it made it upstream just before 2021.01-rc4, likely by
mistake. Revert this patch to put the board back into working order.
Also note that this board has no DM SPL support due to OCRAM size
limitations, but that is fine, as SPL DM support is optional.
[1] https://lists.denx.de/pipermail/u-boot/2020-June/417986.html
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Tom Rini [Sat, 27 Feb 2021 13:06:10 +0000 (08:06 -0500)]
Merge tag 'efi-2021-04-rc3-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2021-04-rc3-2
Bug fixes:
* debug build for mkeficapsule
* limit output length for VenHw, VenMedia
* ACPI tables must be in EfiACPIReclaimMemory
Tom Rini [Fri, 26 Feb 2021 20:11:08 +0000 (15:11 -0500)]
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-usb
- fastboot updates / fixes
Tom Rini [Fri, 26 Feb 2021 17:41:19 +0000 (12:41 -0500)]
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-spi
- new GigaDevice flash ids
- fixes for imx, nxp_spi drivers
Tom Rini [Fri, 26 Feb 2021 17:41:06 +0000 (12:41 -0500)]
Merge tag 'u-boot-stm32-
20210226' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Add USB host boot support in stm32mp1 config
- Enable uefi related commands for STMicroelectronics STM32MP15 boards
- Remove duplicate uart nodes in stm32mp15 device tree