platform/kernel/linux-rpi.git
2 years agomd: update superblock after changing rdev flags in state_store
Xiao Ni [Wed, 13 Oct 2021 14:59:33 +0000 (22:59 +0800)]
md: update superblock after changing rdev flags in state_store

[ Upstream commit 8b9e2291e355a0eafdd5b1e21a94a6659f24b351 ]

When the in memory flag is changed, we need to persist the change in the
rdev superblock flags. This is needed for "writemostly" and "failfast".

Reviewed-by: Li Feng <fengli@smartx.com>
Signed-off-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agofloppy: fix calling platform_device_unregister() on invalid drives
Luis Chamberlain [Mon, 27 Sep 2021 22:02:52 +0000 (15:02 -0700)]
floppy: fix calling platform_device_unregister() on invalid drives

[ Upstream commit 662167e59d2f3c15a44a88088fc6c1a67c8a3650 ]

platform_device_unregister() should only be called when
a respective platform_device_register() is called. However
the floppy driver currently allows failures when registring
a drive and a bail out could easily cause an invalid call
to platform_device_unregister() where it was not intended.

Fix this by adding a bool to keep track of when the platform
device was registered for a drive.

This does not fix any known panic / bug. This issue was found
through code inspection while preparing the driver to use the
up and coming support for device_add_disk() error handling.
From what I can tell from code inspection, chances of this
ever happening should be insanely small, perhaps OOM.

Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20210927220302.1073499-5-mcgrof@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agoblock: bump max plugged deferred size from 16 to 32
Jens Axboe [Wed, 6 Oct 2021 18:01:07 +0000 (12:01 -0600)]
block: bump max plugged deferred size from 16 to 32

[ Upstream commit ba0ffdd8ce48ad7f7e85191cd29f9674caca3745 ]

Particularly for NVMe with efficient deferred submission for many
requests, there are nice benefits to be seen by bumping the default max
plug count from 16 to 32. This is especially true for virtualized setups,
where the submit part is more expensive. But can be noticed even on
native hardware.

Reduce the multiple queue factor from 4 to 2, since we're changing the
default size.

While changing it, move the defines into the block layer private header.
These aren't values that anyone outside of the block layer uses, or
should use.

Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agothermal/drivers/tsens: Add timeout to get_temp_tsens_valid
Ansuel Smith [Thu, 7 Oct 2021 17:28:59 +0000 (19:28 +0200)]
thermal/drivers/tsens: Add timeout to get_temp_tsens_valid

[ Upstream commit d012f9189fda0f3a1b303780ba0bbc7298d0d349 ]

The function can loop and lock the system if for whatever reason the bit
for the target sensor is NEVER valid. This is the case if a sensor is
disabled by the factory and the valid bit is never reported as actually
valid. Add a timeout check and exit if a timeout occurs. As this is
a very rare condition, handle the timeout only if the first read fails.
While at it also rework the function to improve readability and convert
to poll_timeout generic macro.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211007172859.583-1-ansuelsmth@gmail.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agodrm/msm: prevent NULL dereference in msm_gpu_crashstate_capture()
Tim Gardner [Wed, 29 Sep 2021 16:25:54 +0000 (10:25 -0600)]
drm/msm: prevent NULL dereference in msm_gpu_crashstate_capture()

[ Upstream commit b220c154832c5cd0df34cbcbcc19d7135c16e823 ]

Coverity complains of a possible NULL dereference:

CID 120718 (#1 of 1): Dereference null return value (NULL_RETURNS)
23. dereference: Dereferencing a pointer that might be NULL state->bos when
    calling msm_gpu_crashstate_get_bo. [show details]
301                        msm_gpu_crashstate_get_bo(state, submit->bos[i].obj,
302                                submit->bos[i].iova, submit->bos[i].flags);

Fix this by employing the same state->bos NULL check as is used in the next
for loop.

Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210929162554.14295-1-tim.gardner@canonical.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agothermal/core: Fix null pointer dereference in thermal_release()
Yuanzheng Song [Fri, 15 Oct 2021 08:32:30 +0000 (08:32 +0000)]
thermal/core: Fix null pointer dereference in thermal_release()

[ Upstream commit 1dd7128b839f631b31a9e9dce3aaf639bef74e9d ]

If both dev_set_name() and device_register() failed, then null pointer
dereference occurs in thermal_release() which will use strncmp() to
compare the name.

So fix it by adding dev_set_name() return value check.

Signed-off-by: Yuanzheng Song <songyuanzheng@huawei.com>
Link: https://lore.kernel.org/r/20211015083230.67658-1-songyuanzheng@huawei.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agoleaking_addresses: Always print a trailing newline
Kees Cook [Wed, 29 Sep 2021 22:02:18 +0000 (15:02 -0700)]
leaking_addresses: Always print a trailing newline

[ Upstream commit cf2a85efdade117e2169d6e26641016cbbf03ef0 ]

For files that lack trailing newlines and match a leaking address (e.g.
wchan[1]), the leaking_addresses.pl report would run together with the
next line, making things look corrupted.

Unconditionally remove the newline on input, and write it back out on
output.

[1] https://lore.kernel.org/all/20210103142726.GC30643@xsang-OptiPlex-9020/

Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20211008111626.151570317@infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agonet: phy: micrel: make *-skew-ps check more lenient
Matthias Schiffer [Tue, 12 Oct 2021 10:34:02 +0000 (12:34 +0200)]
net: phy: micrel: make *-skew-ps check more lenient

[ Upstream commit 67ca5159dbe2edb5dae7544447b8677d2596933a ]

It seems reasonable to fine-tune only some of the skew values when using
one of the rgmii-*id PHY modes, and even when all skew values are
specified, using the correct ID PHY mode makes sense for documentation
purposes. Such a configuration also appears in the binding docs in
Documentation/devicetree/bindings/net/micrel-ksz90x1.txt, so the driver
should not warn about it.

Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20211012103402.21438-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agodrm/amdkfd: fix resume error when iommu disabled in Picasso
Yifan Zhang [Mon, 11 Oct 2021 12:42:31 +0000 (20:42 +0800)]
drm/amdkfd: fix resume error when iommu disabled in Picasso

[ Upstream commit 6f4b590aae217da16cfa44039a2abcfb209137ab ]

When IOMMU disabled in sbios and kfd in iommuv2 path,
IOMMU resume failure blocks system resume. Don't allow kfd to
use iommu v2 when iommu is disabled.

Reported-by: youling <youling257@gmail.com>
Tested-by: youling <youling257@gmail.com>
Signed-off-by: Yifan Zhang <yifan1.zhang@amd.com>
Reviewed-by: James Zhu <James.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agodrm/amd/display: fix null pointer deref when plugging in display
Aurabindo Pillai [Fri, 8 Oct 2021 20:07:45 +0000 (16:07 -0400)]
drm/amd/display: fix null pointer deref when plugging in display

[ Upstream commit 1f3b22e4eb162e0b1d423106a47484943a22a309 ]

[Why&How]
When system boots in headless mode, connecting a 4k display creates a
null pointer dereference due to hubp for a certain plane being null.
Add a condition to check for null hubp before dereferencing it.

Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agoACPI: scan: Release PM resources blocked by unused objects
Rafael J. Wysocki [Sat, 9 Oct 2021 14:22:09 +0000 (16:22 +0200)]
ACPI: scan: Release PM resources blocked by unused objects

[ Upstream commit c10383e8ddf4810b9a5c1595404c2724d925a0a6 ]

On some systems the ACPI namespace contains device objects that are
not used in certain configurations of the system.  If they start off
in the D0 power state configuration, they will stay in it until the
system reboots, because of the lack of any mechanism possibly causing
their configuration to change.  If that happens, they may prevent
some power resources from being turned off or generally they may
prevent the platform from getting into the deepest low-power states
thus causing some energy to be wasted.

Address this issue by changing the configuration of unused ACPI
device objects to the D3cold power state one after carrying out
the ACPI-based enumeration of devices.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214091
Link: https://lore.kernel.org/linux-acpi/20211007205126.11769-1-mario.limonciello@amd.com/
Reported-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agoACPI: battery: Accept charges over the design capacity as full
André Almeida [Fri, 8 Oct 2021 03:05:29 +0000 (00:05 -0300)]
ACPI: battery: Accept charges over the design capacity as full

[ Upstream commit 2835f327bd1240508db2c89fe94a056faa53c49a ]

Some buggy firmware and/or brand new batteries can support a charge that's
slightly over the reported design capacity. In such cases, the kernel will
report to userspace that the charging state of the battery is "Unknown",
when in reality the battery charge is "Full", at least from the design
capacity point of view. Make the fallback condition accepts capacities
over the designed capacity so userspace knows that is full.

Signed-off-by: André Almeida <andrealmeid@collabora.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agoiov_iter: Fix iov_iter_get_pages{,_alloc} page fault return value
Andreas Gruenbacher [Wed, 21 Jul 2021 17:03:47 +0000 (19:03 +0200)]
iov_iter: Fix iov_iter_get_pages{,_alloc} page fault return value

[ Upstream commit 814a66741b9ffb5e1ba119e368b178edb0b7322d ]

Both iov_iter_get_pages and iov_iter_get_pages_alloc return the number
of bytes of the iovec they could get the pages for.  When they cannot
get any pages, they're supposed to return 0, but when the start of the
iovec isn't page aligned, the calculation goes wrong and they return a
negative value.  Fix both functions.

In addition, change iov_iter_get_pages_alloc to return NULL in that case
to prevent resource leaks.

Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agommc: moxart: Fix reference count leaks in moxart_probe
Xin Xiong [Sat, 9 Oct 2021 04:19:18 +0000 (12:19 +0800)]
mmc: moxart: Fix reference count leaks in moxart_probe

[ Upstream commit 8105c2abbf36296bf38ca44f55ee45d160db476a ]

The issue happens in several error handling paths on two refcounted
object related to the object "host" (dma_chan_rx, dma_chan_tx). In
these paths, the function forgets to decrement one or both objects'
reference count increased earlier by dma_request_chan(), causing
reference count leaks.

Fix it by balancing the refcounts of both objects in some error
handling paths. In correspondence with the changes in moxart_probe(),
IS_ERR() is replaced with IS_ERR_OR_NULL() in moxart_remove() as well.

Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn>
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Link: https://lore.kernel.org/r/20211009041918.28419-1-xiongx18@fudan.edu.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agoKVM: arm64: Propagate errors from __pkvm_prot_finalize hypercall
Will Deacon [Fri, 8 Oct 2021 13:58:37 +0000 (14:58 +0100)]
KVM: arm64: Propagate errors from __pkvm_prot_finalize hypercall

[ Upstream commit 2f2e1a5069679491d18cf9021da19b40c56a17f3 ]

If the __pkvm_prot_finalize hypercall returns an error, we WARN but fail
to propagate the failure code back to kvm_arch_init().

Pass a pointer to a zero-initialised return variable so that failure
to finalise the pKVM protections on a host CPU can be reported back to
KVM.

Cc: Marc Zyngier <maz@kernel.org>
Cc: Quentin Perret <qperret@google.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211008135839.1193-5-will@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agoath: dfs_pattern_detector: Fix possible null-pointer dereference in channel_detector_...
Tuo Li [Thu, 5 Aug 2021 15:38:53 +0000 (08:38 -0700)]
ath: dfs_pattern_detector: Fix possible null-pointer dereference in channel_detector_create()

[ Upstream commit 4b6012a7830b813799a7faf40daa02a837e0fd5b ]

kzalloc() is used to allocate memory for cd->detectors, and if it fails,
channel_detector_exit() behind the label fail will be called:
  channel_detector_exit(dpd, cd);

In channel_detector_exit(), cd->detectors is dereferenced through:
  struct pri_detector *de = cd->detectors[i];

To fix this possible null-pointer dereference, check cd->detectors before
the for loop to dereference cd->detectors.

Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210805153854.154066-1-islituo@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agotracing: Disable "other" permission bits in the tracefs files
Steven Rostedt (VMware) [Wed, 18 Aug 2021 15:24:51 +0000 (11:24 -0400)]
tracing: Disable "other" permission bits in the tracefs files

[ Upstream commit 21ccc9cd72116289469e5519b6159c675a2fa58f ]

When building the files in the tracefs file system, do not by default set
any permissions for OTH (other). This will make it easier for admins who
want to define a group for accessing tracefs and not having to first
disable all the permission bits for "other" in the file system.

As tracing can leak sensitive information, it should never by default
allowing all users access. An admin can still set the permission bits for
others to have access, which may be useful for creating a honeypot and
seeing who takes advantage of it and roots the machine.

Link: https://lkml.kernel.org/r/20210818153038.864149276@goodmis.org
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agotracefs: Have tracefs directories not set OTH permission bits by default
Steven Rostedt (VMware) [Wed, 18 Aug 2021 15:24:50 +0000 (11:24 -0400)]
tracefs: Have tracefs directories not set OTH permission bits by default

[ Upstream commit 49d67e445742bbcb03106b735b2ab39f6e5c56bc ]

The tracefs file system is by default mounted such that only root user can
access it. But there are legitimate reasons to create a group and allow
those added to the group to have access to tracing. By changing the
permissions of the tracefs mount point to allow access, it will allow
group access to the tracefs directory.

There should not be any real reason to allow all access to the tracefs
directory as it contains sensitive information. Have the default
permission of directories being created not have any OTH (other) bits set,
such that an admin that wants to give permission to a group has to first
disable all OTH bits in the file system.

Link: https://lkml.kernel.org/r/20210818153038.664127804@goodmis.org
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agodrm/amdkfd: rm BO resv on validation to avoid deadlock
Alex Sierra [Thu, 7 Oct 2021 17:04:09 +0000 (12:04 -0500)]
drm/amdkfd: rm BO resv on validation to avoid deadlock

[ Upstream commit ec6abe831a843208e99a59adf108adba22166b3f ]

This fix the deadlock with the BO reservations during SVM_BO evictions
while allocations in VRAM are concurrently performed. More specific,
while the ttm waits for the fence to be signaled (ttm_bo_wait), it
already has the BO reserved. In parallel, the restore worker might be
running, prefetching memory to VRAM. This also requires to reserve the
BO, but blocks the mmap semaphore first. The deadlock happens when the
SVM_BO eviction worker kicks in and waits for the mmap semaphore held
in restore worker. Preventing signal the fence back, causing the
deadlock until the ttm times out.

We don't need to hold the BO reservation anymore during validation
and mapping. Now the physical addresses are taken from hmm_range_fault.
We also take migrate_mutex to prevent range migration while
validate_and_map update GPU page table.

Signed-off-by: Alex Sierra <alex.sierra@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Philip Yang <philip.yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agonet-sysfs: try not to restart the syscall if it will fail eventually
Antoine Tenart [Thu, 7 Oct 2021 14:00:51 +0000 (16:00 +0200)]
net-sysfs: try not to restart the syscall if it will fail eventually

[ Upstream commit 146e5e733310379f51924111068f08a3af0db830 ]

Due to deadlocks in the networking subsystem spotted 12 years ago[1],
a workaround was put in place[2] to avoid taking the rtnl lock when it
was not available and restarting the syscall (back to VFS, letting
userspace spin). The following construction is found a lot in the net
sysfs and sysctl code:

  if (!rtnl_trylock())
          return restart_syscall();

This can be problematic when multiple userspace threads use such
interfaces in a short period, making them to spin a lot. This happens
for example when adding and moving virtual interfaces: userspace
programs listening on events, such as systemd-udevd and NetworkManager,
do trigger actions reading files in sysfs. It gets worse when a lot of
virtual interfaces are created concurrently, say when creating
containers at boot time.

Returning early without hitting the above pattern when the syscall will
fail eventually does make things better. While it is not a fix for the
issue, it does ease things.

[1] https://lore.kernel.org/netdev/49A4D5D5.5090602@trash.net/
    https://lore.kernel.org/netdev/m14oyhis31.fsf@fess.ebiederm.org/
    and https://lore.kernel.org/netdev/20090226084924.16cb3e08@nehalam/
[2] Rightfully, those deadlocks are *hard* to solve.

Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agomedia: usb: dvd-usb: fix uninit-value bug in dibusb_read_eeprom_byte()
Anant Thazhemadam [Mon, 7 Dec 2020 06:16:06 +0000 (07:16 +0100)]
media: usb: dvd-usb: fix uninit-value bug in dibusb_read_eeprom_byte()

[ Upstream commit 899a61a3305d49e8a712e9ab20d0db94bde5929f ]

In dibusb_read_eeprom_byte(), if dibusb_i2c_msg() fails, val gets
assigned an value that's not properly initialized.
Using kzalloc() in place of kmalloc() for the buffer fixes this issue,
as the val can now be set to 0 in the event dibusb_i2c_msg() fails.

Reported-by: syzbot+e27b4fd589762b0b9329@syzkaller.appspotmail.com
Tested-by: syzbot+e27b4fd589762b0b9329@syzkaller.appspotmail.com
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agomedia: ipu3-imgu: VIDIOC_QUERYCAP: Fix bus_info
Ricardo Ribalda [Wed, 6 Oct 2021 22:26:22 +0000 (00:26 +0200)]
media: ipu3-imgu: VIDIOC_QUERYCAP: Fix bus_info

[ Upstream commit ea2b9a33711604e91f8c826f4dcb3c12baa1990a ]

bus_info field had a different value for the media entity and the video
device.

Fixes v4l2-compliance:

v4l2-compliance.cpp(637): media bus_info 'PCI:0000:00:05.0' differs from
  V4L2 bus_info 'PCI:viewfinder'

Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agomedia: ipu3-imgu: imgu_fmt: Handle properly try
Ricardo Ribalda [Wed, 6 Oct 2021 22:26:21 +0000 (00:26 +0200)]
media: ipu3-imgu: imgu_fmt: Handle properly try

[ Upstream commit 553481e38045f349bb9aa596d03bebd020020c9c ]

For a try_fmt call, the node noes not need to be enabled.

Fixes v4l2-compliance

fail: v4l2-test-formats.cpp(717): Video Output Multiplanar is valid, but
  no TRY_FMT was implemented
test VIDIOC_TRY_FMT: FAIL

Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agomedia: imx-jpeg: Fix possible null pointer dereference
Mirela Rabulea [Mon, 27 Sep 2021 18:56:32 +0000 (20:56 +0200)]
media: imx-jpeg: Fix possible null pointer dereference

[ Upstream commit 83f5f0633b156c636f5249d3c10f2a9423dd4c96 ]

Found by Coverity scan.

Signed-off-by: Mirela Rabulea <mirela.rabulea@nxp.com>
Reviewed-by: Laurentiu Palcu <laurentiu.palcu@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agoice: Move devlink port to PF/VF struct
Wojciech Drewek [Fri, 20 Aug 2021 00:08:49 +0000 (17:08 -0700)]
ice: Move devlink port to PF/VF struct

[ Upstream commit 2ae0aa4758b0f4a247d45cb3bf01548a7f396751 ]

Keeping devlink port inside VSI data structure causes some issues.
Since VF VSI is released during reset that means that we have to
unregister devlink port and register it again every time reset is
triggered. With the new changes in devlink API it
might cause deadlock issues. After calling
devlink_port_register/devlink_port_unregister devlink API is going to
lock rtnl_mutex. It's an issue when VF reset is triggered in netlink
operation context (like setting VF MAC address or VLAN),
because rtnl_lock is already taken by netlink. Another call of
rtnl_lock from devlink API results in dead-lock.

By moving devlink port to PF/VF we avoid creating/destroying it
during reset. Since this patch, devlink ports are created during
ice_probe, destroyed during ice_remove for PF and created during
ice_repr_add, destroyed during ice_repr_rem for VF.

Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agocpufreq: Make policy min/max hard requirements
Vincent Donnefort [Wed, 8 Sep 2021 14:05:26 +0000 (15:05 +0100)]
cpufreq: Make policy min/max hard requirements

[ Upstream commit 15171769069408789a72f9aa9a52cc931b839b56 ]

When applying the policy min/max limits, the requested frequency is
simply clamped to not be out of range. It means, however, if one of the
boundaries isn't an available frequency, the frequency resolution can
return a value out of those limits, depending on the relation used.

e.g. freq{0,1,2} being available frequencies.

          freq0  policy->min  freq1  policy->max   freq2
            |        |          |        |           |
          17kHz     18kHz     19kHz     20kHz      21kHz

     __resolve_freq(21kHz, CPUFREQ_RELATION_L) -> 21kHz (out of bounds)
     __resolve_freq(17kHz, CPUFREQ_RELATION_H) -> 17kHz (out of bounds)

If, during the policy init, we resolve the requested min/max to existing
frequencies, we ensure that any CPUFREQ_RELATION_* would resolve to a
frequency which is inside the policy min/max range.

Making the policy limits rigid helps to introduce the inefficient
frequencies support. Resolving an inefficient frequency to an efficient
one should not transgress policy->max (which can be set for thermal
reason) and having a value we can trust simplify this comparison.

Signed-off-by: Vincent Donnefort <vincent.donnefort@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agoACPICA: Avoid evaluating methods too early during system resume
Rafael J. Wysocki [Wed, 29 Sep 2021 16:31:25 +0000 (18:31 +0200)]
ACPICA: Avoid evaluating methods too early during system resume

[ Upstream commit d3c4b6f64ad356c0d9ddbcf73fa471e6a841cc5c ]

ACPICA commit 0762982923f95eb652cf7ded27356b247c9774de

During wakeup from system-wide sleep states, acpi_get_sleep_type_data()
is called and it tries to get memory from the slab allocator in order
to evaluate a control method, but if KFENCE is enabled in the kernel,
the memory allocation attempt causes an IRQ work to be queued and a
self-IPI to be sent to the CPU running the code which requires the
memory controller to be ready, so if that happens too early in the
wakeup path, it doesn't work.

Prevent that from taking place by calling acpi_get_sleep_type_data()
for S0 upfront, when preparing to enter a given sleep state, and
saving the data obtained by it for later use during system wakeup.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214271
Reported-by: Reik Keutterling <spielkind@gmail.com>
Tested-by: Reik Keutterling <spielkind@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agokselftests/sched: cleanup the child processes
Li Zhijian [Thu, 2 Sep 2021 02:43:33 +0000 (10:43 +0800)]
kselftests/sched: cleanup the child processes

[ Upstream commit 1c36432b278cecf1499f21fae19836e614954309 ]

Previously, 'make -C sched run_tests' will block forever when it occurs
something wrong where the *selftests framework* is waiting for its child
processes to exit.

[root@iaas-rpma sched]# ./cs_prctl_test

 ## Create a thread/process/process group hiearchy
Not a core sched system
tid=74985, / tgid=74985 / pgid=74985: ffffffffffffffff
Not a core sched system
    tid=74986, / tgid=74986 / pgid=74985: ffffffffffffffff
Not a core sched system
        tid=74988, / tgid=74986 / pgid=74985: ffffffffffffffff
Not a core sched system
        tid=74989, / tgid=74986 / pgid=74985: ffffffffffffffff
Not a core sched system
        tid=74990, / tgid=74986 / pgid=74985: ffffffffffffffff
Not a core sched system
    tid=74987, / tgid=74987 / pgid=74985: ffffffffffffffff
Not a core sched system
        tid=74991, / tgid=74987 / pgid=74985: ffffffffffffffff
Not a core sched system
        tid=74992, / tgid=74987 / pgid=74985: ffffffffffffffff
Not a core sched system
        tid=74993, / tgid=74987 / pgid=74985: ffffffffffffffff

Not a core sched system
(268) FAILED: get_cs_cookie(0) == 0

 ## Set a cookie on entire process group
-1 = prctl(62, 1, 0, 2, 0)
core_sched create failed -- PGID: Invalid argument
(cs_prctl_test.c:272) -
[root@iaas-rpma sched]# ps
    PID TTY          TIME CMD
   4605 pts/2    00:00:00 bash
  74986 pts/2    00:00:00 cs_prctl_test
  74987 pts/2    00:00:00 cs_prctl_test
  74999 pts/2    00:00:00 ps

Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Chris Hyser <chris.hyser@oracle.com>
Link: https://lore.kernel.org/r/20210902024333.75983-1-lizhijian@cn.fujitsu.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agofs/proc/uptime.c: Fix idle time reporting in /proc/uptime
Josh Don [Fri, 27 Aug 2021 16:54:38 +0000 (09:54 -0700)]
fs/proc/uptime.c: Fix idle time reporting in /proc/uptime

[ Upstream commit a130e8fbc7de796eb6e680724d87f4737a26d0ac ]

/proc/uptime reports idle time by reading the CPUTIME_IDLE field from
the per-cpu kcpustats. However, on NO_HZ systems, idle time is not
continually updated on idle cpus, leading this value to appear
incorrectly small.

/proc/stat performs an accounting update when reading idle time; we
can use the same approach for uptime.

With this patch, /proc/stat and /proc/uptime now agree on idle time.
Additionally, the following shows idle time tick up consistently on an
idle machine:

  (while true; do cat /proc/uptime; sleep 1; done) | awk '{print $2-prev; prev=$2}'

Reported-by: Luigi Rizzo <lrizzo@google.com>
Signed-off-by: Josh Don <joshdon@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lkml.kernel.org/r/20210827165438.3280779-1-joshdon@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agoipmi: Disable some operations during a panic
Corey Minyard [Thu, 16 Sep 2021 16:36:20 +0000 (11:36 -0500)]
ipmi: Disable some operations during a panic

[ Upstream commit b36eb5e7b75a756baa64909a176dd4269ee05a8b ]

Don't do kfree or other risky things when oops_in_progress is set.
It's easy enough to avoid doing them

Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agomedia: rcar-csi2: Add checking to rcsi2_start_receiver()
Nadezda Lutovinova [Wed, 11 Aug 2021 17:18:16 +0000 (19:18 +0200)]
media: rcar-csi2: Add checking to rcsi2_start_receiver()

[ Upstream commit fc41665498332ad394b7db37f23e9394096ddc71 ]

If rcsi2_code_to_fmt() return NULL, then null pointer dereference occurs
in the next cycle. That should not be possible now but adding checking
protects from future bugs.
The patch adds checking if format is NULL.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agobrcmfmac: Add DMI nvram filename quirk for Cyberbook T116 tablet
Hans de Goede [Tue, 28 Sep 2021 16:06:33 +0000 (18:06 +0200)]
brcmfmac: Add DMI nvram filename quirk for Cyberbook T116 tablet

[ Upstream commit 49c3eb3036e6359c5c20fe76c611a2c0e0d4710e ]

The Cyberbook T116 tablet contains quite generic names in the sys_vendor
and product_name DMI strings, without this patch brcmfmac will try to load:
"brcmfmac43455-sdio.Default string-Default string.txt" as nvram file which
is way too generic.

The nvram file shipped on the factory Android image contains the exact
same settings as those used on the AcePC T8 mini PC, so point the new
DMI nvram filename quirk to the acepc-t8 nvram file.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210928160633.96928-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agortw88: fix RX clock gate setting while fifo dump
Zong-Zhe Yang [Mon, 27 Sep 2021 11:18:30 +0000 (19:18 +0800)]
rtw88: fix RX clock gate setting while fifo dump

[ Upstream commit c5a8e90730a322f236731fc347dd3afa5db5550e ]

When fw fifo dumps, RX clock gating should be disabled to avoid
something unexpected. However, the register operation ran into
a mistake. So, we fix it.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210927111830.5354-1-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agoia64: don't do IA64_CMPXCHG_DEBUG without CONFIG_PRINTK
Randy Dunlap [Sun, 26 Sep 2021 17:12:24 +0000 (10:12 -0700)]
ia64: don't do IA64_CMPXCHG_DEBUG without CONFIG_PRINTK

[ Upstream commit c15b5fc054c3d6c97e953617605235c5cb8ce979 ]

When CONFIG_PRINTK is not set, the CMPXCHG_BUGCHECK() macro calls
_printk(), but _printk() is a static inline function, not available
as an extern.
Since the purpose of the macro is to print the BUGCHECK info,
make this config option depend on PRINTK.

Fixes multiple occurrences of this build error:

../include/linux/printk.h:208:5: error: static declaration of '_printk' follows non-static declaration
  208 | int _printk(const char *s, ...)
      |     ^~~~~~~
In file included from ../arch/ia64/include/asm/cmpxchg.h:5,
../arch/ia64/include/uapi/asm/cmpxchg.h:146:28: note: previous declaration of '_printk' with type 'int(const char *, ...)'
  146 |                 extern int _printk(const char *fmt, ...);

Cc: linux-ia64@vger.kernel.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Chris Down <chris@chrisdown.name>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agomedia: mceusb: return without resubmitting URB in case of -EPROTO error.
Rajat Asthana [Wed, 18 Aug 2021 20:31:10 +0000 (22:31 +0200)]
media: mceusb: return without resubmitting URB in case of -EPROTO error.

[ Upstream commit 476db72e521983ecb847e4013b263072bb1110fc ]

Syzkaller reported a warning called "rcu detected stall in dummy_timer".

The error seems to be an error in mceusb_dev_recv(). In the case of
-EPROTO error, the routine immediately resubmits the URB. Instead it
should return without resubmitting URB.

Reported-by: syzbot+4d3749e9612c2cfab956@syzkaller.appspotmail.com
Signed-off-by: Rajat Asthana <rajatasthana4@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agomedia: rcar-vin: Use user provided buffers when starting
Niklas Söderlund [Sat, 11 Sep 2021 19:19:58 +0000 (21:19 +0200)]
media: rcar-vin: Use user provided buffers when starting

[ Upstream commit a5991c4e947153418f71f4689614b87ca0551b81 ]

When adding an internal scratch buffer to improve buffer handling when
stopping it was also erroneously used when syncing at capture start.
This led to that the first three buffers captured were always dropped
as they were captured in the scratch buffer instead of in a buffer
provided by the user.

Allow the hardware to be given user provided buffers when preparing for
capture in the stopped state. This still allows the driver to sync with
the hardware and always completes the buffers to user-space in the
correct order as no buffers are completed before the sync is complete.
This change improves the driver as buffers are completed and given to
the user three frames earlier than before.

The change also fixes a warning produced by v4l2-compliance,

    warn: v4l2-test-buffers.cpp(448): got sequence number 3, expected 0

[hverkuil: fixed some typos in the Subject and the log message]

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agomedia: imx: set a media_device bus_info string
Martin Kepplinger [Wed, 8 Sep 2021 08:47:46 +0000 (10:47 +0200)]
media: imx: set a media_device bus_info string

[ Upstream commit 6d0d779b212c27293d9ccb4da092ff0ccb6efa39 ]

Some tools like v4l2-compliance let users select a media device based
on the bus_info string which can be quite convenient. Use a unique
string for that.

This also fixes the following v4l2-compliance warning:
warn: v4l2-test-media.cpp(52): empty bus_info

Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agomedia: videobuf2: rework vb2_mem_ops API
Sergey Senozhatsky [Thu, 9 Sep 2021 11:24:23 +0000 (13:24 +0200)]
media: videobuf2: rework vb2_mem_ops API

[ Upstream commit a4b83deb3e76fb9385ca58e2c072a145b3a320d6 ]

With the new DMA API we need an extension of the videobuf2 API.
Previously, videobuf2 core would set the non-coherent DMA bit
in the vb2_queue dma_attr field (if user-space would pass a
corresponding memory hint); the vb2 core then would pass the
vb2_queue dma_attrs to the vb2 allocators. The vb2 allocator
would use the queue's dma_attr and the DMA API would allocate
either coherent or non-coherent memory.

But we cannot do this anymore, since there is no corresponding DMA
attr flag and, hence, there is no way for the allocator to become
aware of what type of allocation user-space has requested. So we
need to pass more context from videobuf2 core to the allocators.

Fix this by changing the call_ptr_memop() macro to pass the
vb2 pointer to the corresponding op callbacks.

Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agomedia: s5p-mfc: Add checking to s5p_mfc_probe().
Nadezda Lutovinova [Wed, 11 Aug 2021 13:32:28 +0000 (15:32 +0200)]
media: s5p-mfc: Add checking to s5p_mfc_probe().

[ Upstream commit cdfaf4752e6915a4b455ad4400133e540e4dc965 ]

If of_device_get_match_data() return NULL,
then null pointer dereference occurs in  s5p_mfc_init_pm().
The patch adds checking if dev->variant is NULL.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agomedia: s5p-mfc: fix possible null-pointer dereference in s5p_mfc_probe()
Tuo Li [Thu, 5 Aug 2021 07:55:35 +0000 (09:55 +0200)]
media: s5p-mfc: fix possible null-pointer dereference in s5p_mfc_probe()

[ Upstream commit 8515965e5e33f4feb56134348c95953f3eadfb26 ]

The variable pdev is assigned to dev->plat_dev, and dev->plat_dev is
checked in:
  if (!dev->plat_dev)

This indicates both dev->plat_dev and pdev can be NULL. If so, the
function dev_err() is called to print error information.
  dev_err(&pdev->dev, "No platform data specified\n");

However, &pdev->dev is an illegal address, and it is dereferenced in
dev_err().

To fix this possible null-pointer dereference, replace dev_err() with
mfc_err().

Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agomedia: vidtv: Fix memory leak in remove
Evgeny Novikov [Thu, 27 May 2021 09:26:24 +0000 (11:26 +0200)]
media: vidtv: Fix memory leak in remove

[ Upstream commit 76e21bb8be4f5f987f3006d197196fe6af63f656 ]

vidtv_bridge_remove() releases and cleans up everything except for dvb
itself. The patch adds this missed release.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agomedia: uvcvideo: Set unique vdev name based in type
Ricardo Ribalda [Fri, 18 Jun 2021 12:29:13 +0000 (14:29 +0200)]
media: uvcvideo: Set unique vdev name based in type

[ Upstream commit e3f60e7e1a2b451f538f9926763432249bcf39c4 ]

All the entities must have a unique name. We can have a descriptive and
unique name by appending the function and the entity->id.

This is even resilent to multi chain devices.

Fixes v4l2-compliance:
Media Controller ioctls:
                fail: v4l2-test-media.cpp(205): v2_entity_names_set.find(key) != v2_entity_names_set.end()
        test MEDIA_IOC_G_TOPOLOGY: FAIL
                fail: v4l2-test-media.cpp(394): num_data_links != num_links
test MEDIA_IOC_ENUM_ENTITIES/LINKS: FAIL

Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agomedia: uvcvideo: Return -EIO for control errors
Ricardo Ribalda [Fri, 18 Jun 2021 12:29:09 +0000 (14:29 +0200)]
media: uvcvideo: Return -EIO for control errors

[ Upstream commit ffccdde5f0e17d2f0d788a9d831a027187890eaa ]

The device is doing something unexpected with the control. Either because
the protocol is not properly implemented or there has been a HW error.

Fixes v4l2-compliance:

Control ioctls (Input 0):
                fail: v4l2-test-controls.cpp(448): s_ctrl returned an error (22)
        test VIDIOC_G/S_CTRL: FAIL
                fail: v4l2-test-controls.cpp(698): s_ext_ctrls returned an error (22)
        test VIDIOC_G/S/TRY_EXT_CTRLS: FAIL

Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agomedia: uvcvideo: Set capability in s_param
Ricardo Ribalda [Fri, 18 Jun 2021 12:29:08 +0000 (14:29 +0200)]
media: uvcvideo: Set capability in s_param

[ Upstream commit 97a2777a96070afb7da5d587834086c0b586c8cc ]

Fixes v4l2-compliance:

Format ioctls (Input 0):
                warn: v4l2-test-formats.cpp(1339): S_PARM is supported but doesn't report V4L2_CAP_TIMEPERFRAME
                fail: v4l2-test-formats.cpp(1241): node->has_frmintervals && !cap->capability

Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agomedia: stm32: Potential NULL pointer dereference in dcmi_irq_thread()
Dmitriy Ulitin [Thu, 27 May 2021 15:06:26 +0000 (17:06 +0200)]
media: stm32: Potential NULL pointer dereference in dcmi_irq_thread()

[ Upstream commit 548fa43a58696450c15b8f5564e99589c5144664 ]

At the moment of enabling irq handling:

1922 ret = devm_request_threaded_irq(&pdev->dev, irq, dcmi_irq_callback,
1923 dcmi_irq_thread, IRQF_ONESHOT,
1924 dev_name(&pdev->dev), dcmi);

there is still uninitialized field sd_format of struct stm32_dcmi *dcmi.
If an interrupt occurs in the interval between the installation of the
interrupt handler and the initialization of this field, NULL pointer
dereference happens.

This field is dereferenced in the handler function without any check:

457 if (dcmi->sd_format->fourcc == V4L2_PIX_FMT_JPEG &&
458     dcmi->misr & IT_FRAME) {

The patch moves interrupt handler installation
after initialization of the sd_format field that happens in
dcmi_graph_notify_complete() via dcmi_set_default_fmt().

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Dmitriy Ulitin <ulitin@ispras.ru>
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agomedia: atomisp: Fix error handling in probe
Evgeny Novikov [Tue, 10 Aug 2021 16:29:43 +0000 (18:29 +0200)]
media: atomisp: Fix error handling in probe

[ Upstream commit e16f5e39acd6d10cc63ae39bc0a77188ed828f22 ]

There were several issues with handling errors in lm3554_probe():
- Probe did not set the error code when v4l2_ctrl_handler_init() failed.
- It intermixed gotos for handling errors of v4l2_ctrl_handler_init()
  and media_entity_pads_init().
- It did not set the error code for failures of v4l2_ctrl_new_custom().
- Probe did not free resources in case of failures of
  atomisp_register_i2c_module().

The patch fixes all these issues.

Found by Linux Driver Verification project (linuxtesting.org).

Link: https://lore.kernel.org/linux-media/20210810162943.19852-1-novikov@ispras.ru
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agomedia: netup_unidvb: handle interrupt properly according to the firmware
Zheyu Ma [Wed, 23 Jun 2021 06:01:05 +0000 (08:01 +0200)]
media: netup_unidvb: handle interrupt properly according to the firmware

[ Upstream commit dbb4cfea6efe979ed153bd59a6a527a90d3d0ab3 ]

The interrupt handling should be related to the firmware version. If
the driver matches an old firmware, then the driver should not handle
interrupt such as i2c or dma, otherwise it will cause some errors.

This log reveals it:

[   27.708641] INFO: trying to register non-static key.
[   27.710851] The code is fine but needs lockdep annotation, or maybe
[   27.712010] you didn't initialize this object before use?
[   27.712396] turning off the locking correctness validator.
[   27.712787] CPU: 2 PID: 0 Comm: swapper/2 Not tainted 5.12.4-g70e7f0549188-dirty #169
[   27.713349] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014
[   27.714149] Call Trace:
[   27.714329]  <IRQ>
[   27.714480]  dump_stack+0xba/0xf5
[   27.714737]  register_lock_class+0x873/0x8f0
[   27.715052]  ? __lock_acquire+0x323/0x1930
[   27.715353]  __lock_acquire+0x75/0x1930
[   27.715636]  lock_acquire+0x1dd/0x3e0
[   27.715905]  ? netup_i2c_interrupt+0x19/0x310
[   27.716226]  _raw_spin_lock_irqsave+0x4b/0x60
[   27.716544]  ? netup_i2c_interrupt+0x19/0x310
[   27.716863]  netup_i2c_interrupt+0x19/0x310
[   27.717178]  netup_unidvb_isr+0xd3/0x160
[   27.717467]  __handle_irq_event_percpu+0x53/0x3e0
[   27.717808]  handle_irq_event_percpu+0x35/0x90
[   27.718129]  handle_irq_event+0x39/0x60
[   27.718409]  handle_fasteoi_irq+0xc2/0x1d0
[   27.718707]  __common_interrupt+0x7f/0x150
[   27.719008]  common_interrupt+0xb4/0xd0
[   27.719289]  </IRQ>
[   27.719446]  asm_common_interrupt+0x1e/0x40
[   27.719747] RIP: 0010:native_safe_halt+0x17/0x20
[   27.720084] Code: 07 0f 00 2d 8b ee 4c 00 f4 5d c3 0f 1f 84 00 00 00 00 00 8b 05 72 95 17 02 55 48 89 e5 85 c0 7e 07 0f 00 2d 6b ee 4c 00 fb f4 <5d> c3 cc cc cc cc cc cc cc 55 48 89 e5 e8 67 53 ff ff 8b 0d 29 f6
[   27.721386] RSP: 0018:ffffc9000008fe90 EFLAGS: 00000246
[   27.721758] RAX: 0000000000000000 RBX: 0000000000000002 RCX: 0000000000000000
[   27.722262] RDX: 0000000000000000 RSI: ffffffff85f7c054 RDI: ffffffff85ded4e6
[   27.722770] RBP: ffffc9000008fe90 R08: 0000000000000001 R09: 0000000000000001
[   27.723277] R10: 0000000000000000 R11: 0000000000000001 R12: ffffffff86a75408
[   27.723781] R13: 0000000000000000 R14: 0000000000000000 R15: ffff888100260000
[   27.724289]  default_idle+0x9/0x10
[   27.724537]  arch_cpu_idle+0xa/0x10
[   27.724791]  default_idle_call+0x6e/0x250
[   27.725082]  do_idle+0x1f0/0x2d0
[   27.725326]  cpu_startup_entry+0x18/0x20
[   27.725613]  start_secondary+0x11f/0x160
[   27.725902]  secondary_startup_64_no_verify+0xb0/0xbb
[   27.726272] BUG: kernel NULL pointer dereference, address: 0000000000000002
[   27.726768] #PF: supervisor read access in kernel mode
[   27.727138] #PF: error_code(0x0000) - not-present page
[   27.727507] PGD 8000000118688067 P4D 8000000118688067 PUD 10feab067 PMD 0
[   27.727999] Oops: 0000 [#1] PREEMPT SMP PTI
[   27.728302] CPU: 2 PID: 0 Comm: swapper/2 Not tainted 5.12.4-g70e7f0549188-dirty #169
[   27.728861] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014
[   27.729660] RIP: 0010:netup_i2c_interrupt+0x23/0x310
[   27.730019] Code: 0f 1f 80 00 00 00 00 55 48 89 e5 41 55 41 54 53 48 89 fb e8 af 6e 95 fd 48 89 df e8 e7 9f 1c 01 49 89 c5 48 8b 83 48 08 00 00 <66> 44 8b 60 02 44 89 e0 48 8b 93 48 08 00 00 83 e0 f8 66 89 42 02
[   27.731339] RSP: 0018:ffffc90000118e90 EFLAGS: 00010046
[   27.731716] RAX: 0000000000000000 RBX: ffff88810803c4d8 RCX: 0000000000000000
[   27.732223] RDX: 0000000000000001 RSI: ffffffff85d37b94 RDI: ffff88810803c4d8
[   27.732727] RBP: ffffc90000118ea8 R08: 0000000000000000 R09: 0000000000000001
[   27.733239] R10: ffff88810803c4f0 R11: 61646e6f63657320 R12: 0000000000000000
[   27.733745] R13: 0000000000000046 R14: ffff888101041000 R15: ffff8881081b2400
[   27.734251] FS:  0000000000000000(0000) GS:ffff88817bc80000(0000) knlGS:0000000000000000
[   27.734821] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   27.735228] CR2: 0000000000000002 CR3: 0000000108194000 CR4: 00000000000006e0
[   27.735735] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   27.736241] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[   27.736744] Call Trace:
[   27.736924]  <IRQ>
[   27.737074]  netup_unidvb_isr+0xd3/0x160
[   27.737363]  __handle_irq_event_percpu+0x53/0x3e0
[   27.737706]  handle_irq_event_percpu+0x35/0x90
[   27.738028]  handle_irq_event+0x39/0x60
[   27.738306]  handle_fasteoi_irq+0xc2/0x1d0
[   27.738602]  __common_interrupt+0x7f/0x150
[   27.738899]  common_interrupt+0xb4/0xd0
[   27.739176]  </IRQ>
[   27.739331]  asm_common_interrupt+0x1e/0x40
[   27.739633] RIP: 0010:native_safe_halt+0x17/0x20
[   27.739967] Code: 07 0f 00 2d 8b ee 4c 00 f4 5d c3 0f 1f 84 00 00 00 00 00 8b 05 72 95 17 02 55 48 89 e5 85 c0 7e 07 0f 00 2d 6b ee 4c 00 fb f4 <5d> c3 cc cc cc cc cc cc cc 55 48 89 e5 e8 67 53 ff ff 8b 0d 29 f6
[   27.741275] RSP: 0018:ffffc9000008fe90 EFLAGS: 00000246
[   27.741647] RAX: 0000000000000000 RBX: 0000000000000002 RCX: 0000000000000000
[   27.742148] RDX: 0000000000000000 RSI: ffffffff85f7c054 RDI: ffffffff85ded4e6
[   27.742652] RBP: ffffc9000008fe90 R08: 0000000000000001 R09: 0000000000000001
[   27.743154] R10: 0000000000000000 R11: 0000000000000001 R12: ffffffff86a75408
[   27.743652] R13: 0000000000000000 R14: 0000000000000000 R15: ffff888100260000
[   27.744157]  default_idle+0x9/0x10
[   27.744405]  arch_cpu_idle+0xa/0x10
[   27.744658]  default_idle_call+0x6e/0x250
[   27.744948]  do_idle+0x1f0/0x2d0
[   27.745190]  cpu_startup_entry+0x18/0x20
[   27.745475]  start_secondary+0x11f/0x160
[   27.745761]  secondary_startup_64_no_verify+0xb0/0xbb
[   27.746123] Modules linked in:
[   27.746348] Dumping ftrace buffer:
[   27.746596]    (ftrace buffer empty)
[   27.746852] CR2: 0000000000000002
[   27.747094] ---[ end trace ebafd46f83ab946d ]---
[   27.747424] RIP: 0010:netup_i2c_interrupt+0x23/0x310
[   27.747778] Code: 0f 1f 80 00 00 00 00 55 48 89 e5 41 55 41 54 53 48 89 fb e8 af 6e 95 fd 48 89 df e8 e7 9f 1c 01 49 89 c5 48 8b 83 48 08 00 00 <66> 44 8b 60 02 44 89 e0 48 8b 93 48 08 00 00 83 e0 f8 66 89 42 02
[   27.749082] RSP: 0018:ffffc90000118e90 EFLAGS: 00010046
[   27.749461] RAX: 0000000000000000 RBX: ffff88810803c4d8 RCX: 0000000000000000
[   27.749966] RDX: 0000000000000001 RSI: ffffffff85d37b94 RDI: ffff88810803c4d8
[   27.750471] RBP: ffffc90000118ea8 R08: 0000000000000000 R09: 0000000000000001
[   27.750976] R10: ffff88810803c4f0 R11: 61646e6f63657320 R12: 0000000000000000
[   27.751480] R13: 0000000000000046 R14: ffff888101041000 R15: ffff8881081b2400
[   27.751986] FS:  0000000000000000(0000) GS:ffff88817bc80000(0000) knlGS:0000000000000000
[   27.752560] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   27.752970] CR2: 0000000000000002 CR3: 0000000108194000 CR4: 00000000000006e0
[   27.753481] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   27.753984] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[   27.754487] Kernel panic - not syncing: Fatal exception in interrupt
[   27.755033] Dumping ftrace buffer:
[   27.755279]    (ftrace buffer empty)
[   27.755534] Kernel Offset: disabled
[   27.755785] Rebooting in 1 seconds..

Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agomedia: mt9p031: Fix corrupted frame after restarting stream
Dirk Bender [Mon, 26 Jul 2021 07:35:15 +0000 (09:35 +0200)]
media: mt9p031: Fix corrupted frame after restarting stream

[ Upstream commit 0961ba6dd211a4a52d1dd4c2d59be60ac2dc08c7 ]

To prevent corrupted frames after starting and stopping the sensor its
datasheet specifies a specific pause sequence to follow:

Stopping:
Set Pause_Restart Bit -> Set Restart Bit -> Set Chip_Enable Off

Restarting:
Set Chip_Enable On -> Clear Pause_Restart Bit

The Restart Bit is cleared automatically and must not be cleared
manually as this would cause undefined behavior.

Signed-off-by: Dirk Bender <d.bender@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agoocteontx2-pf: Enable promisc/allmulti match MCAM entries.
Rakesh Babu [Tue, 28 Sep 2021 17:43:45 +0000 (23:13 +0530)]
octeontx2-pf: Enable promisc/allmulti match MCAM entries.

[ Upstream commit ffd2f89ad05cd620d822112a07b0c5669fa9e333 ]

Whenever the interface is brought up/down then set_rx_mode
function is called by the stack which enables promisc/allmulti
MCAM entries. But there are cases when driver brings
interface down and then up such as while changing number
of channels. In these cases promisc/allmulti MCAM entries
are left disabled as set_rx_mode callback is not called.
This patch enables these MCAM entries in all such cases.

Signed-off-by: Rakesh Babu <rsaladi2@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agoath10k: high latency fixes for beacon buffer
Alagu Sankar [Tue, 28 Sep 2021 11:00:47 +0000 (14:00 +0300)]
ath10k: high latency fixes for beacon buffer

[ Upstream commit e263bdab9c0e8025fb7f41f153709a9cda51f6b6 ]

Beacon buffer for high latency devices does not use DMA. other similar
buffer allocation methods in the driver have already been modified for
high latency path. Fix the beacon buffer allocation left out in the
earlier high latency changes.

Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
[fabio: adapt it to use ar->bus_param.dev_type ]
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210818232627.2040121-1-festevam@denx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agoath11k: Change DMA_FROM_DEVICE to DMA_TO_DEVICE when map reinjected packets
Baochen Qiang [Tue, 28 Sep 2021 11:00:46 +0000 (14:00 +0300)]
ath11k: Change DMA_FROM_DEVICE to DMA_TO_DEVICE when map reinjected packets

[ Upstream commit 86a03dad0f5ad8182ed5fcf7bf3eec71cd96577c ]

For fragmented packets, ath11k reassembles each fragment as a normal
packet and then reinjects it into HW ring. In this case, the DMA
direction should be DMA_TO_DEVICE, not DMA_FROM_DEVICE, otherwise
invalid payload will be reinjected to HW and then delivered to host.
What is more, since arbitrary memory could be allocated to the frame, we
don't know what kind of data is contained in the buffer reinjected.
Thus, as a bad result, private info may be leaked.

Note that this issue is only found on Intel platform.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916064617.20006-1-bqiang@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agoath11k: add handler for scan event WMI_SCAN_EVENT_DEQUEUED
Wen Gong [Tue, 28 Sep 2021 11:00:45 +0000 (14:00 +0300)]
ath11k: add handler for scan event WMI_SCAN_EVENT_DEQUEUED

[ Upstream commit 441b3b5911f8ead7f2fe2336587b340a33044d58 ]

When wlan interface is up, 11d scan is sent to the firmware, and the
firmware needs to spend couple of seconds to complete the 11d scan. If
immediately a normal scan from user space arrives to ath11k, then the
normal scan request is also sent to the firmware, but the scan started
event will be reported to ath11k until the 11d scan complete. When timed
out for the scan started in ath11k, ath11k stops the normal scan and the
firmware reports WMI_SCAN_EVENT_DEQUEUED to ath11k for the normal scan.
ath11k has no handler for the event and then timed out for the scan
completed in ath11k_scan_stop(), and ath11k prints the following error
message.

[ 1491.604750] ath11k_pci 0000:02:00.0: failed to receive scan abort comple: timed out
[ 1491.604756] ath11k_pci 0000:02:00.0: failed to stop scan: -110
[ 1491.604758] ath11k_pci 0000:02:00.0: failed to start hw scan: -110

Add a handler for WMI_SCAN_EVENT_DEQUEUED and then complete the scan to
get rid of the above error message.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1

Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914164226.38843-1-jouni@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agoath11k: Avoid reg rules update during firmware recovery
Sriram R [Tue, 28 Sep 2021 09:05:40 +0000 (12:05 +0300)]
ath11k: Avoid reg rules update during firmware recovery

[ Upstream commit 69a0fcf8a9f2273040d03e5ee77c9689c09e9d3a ]

During firmware recovery, the default reg rules which are
received via WMI_REG_CHAN_LIST_CC_EVENT can overwrite
the currently configured user regd.

See below snap for example,

root@OpenWrt:/# iw reg get | grep country
country FR: DFS-ETSI
country FR: DFS-ETSI
country FR: DFS-ETSI
country FR: DFS-ETSI

root@OpenWrt:/# echo assert > /sys/kernel/debug/ath11k/ipq8074\ hw2.0/simulate_f
w_crash
<snip>
[ 5290.471696] ath11k c000000.wifi1: pdev 1 successfully recovered

root@OpenWrt:/# iw reg get | grep country
country FR: DFS-ETSI
country US: DFS-FCC
country US: DFS-FCC
country US: DFS-FCC

In the above, the user configured country 'FR' is overwritten
when the rules of default country 'US' are received and updated during
recovery. Hence avoid processing of these rules in general
during firmware recovery as they have been already applied during
driver registration or after last set user country is configured.

This scenario applies for both AP and STA devices basically because
cfg80211 is not aware of the recovery and only the driver recovers, but
changing or resetting of the reg domain during recovery is not needed so
as to continue with the configured regdomain currently in use.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01460-QCAHKSWPL_SILICONZ-1

Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-3-jouni@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agoselftests: net: fib_nexthops: Wait before checking reported idle time
Petr Machata [Fri, 24 Sep 2021 10:04:27 +0000 (12:04 +0200)]
selftests: net: fib_nexthops: Wait before checking reported idle time

[ Upstream commit b69c99463d414cc263411462d52f25205657e9af ]

The purpose of this test is to verify that after a short activity passes,
the reported time is reasonable: not zero (which could be reported by
mistake), and not something outrageous (which would be indicative of an
issue in used units).

However, the idle time is reported in units of clock_t, or hundredths of
second. If the initial sequence of commands is very quick, it is possible
that the idle time is reported as just flat-out zero. When this test was
recently enabled in our nightly regression, we started seeing spurious
failures for exactly this reason.

Therefore buffer the delay leading up to the test with a sleep, to make
sure there is no legitimate way of reporting 0.

Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agodrm/amd/display: Fix null pointer dereference for encoders
Jimmy Kizito [Sun, 12 Sep 2021 15:21:52 +0000 (11:21 -0400)]
drm/amd/display: Fix null pointer dereference for encoders

[ Upstream commit 60f39edd897ea134a4ddb789a6795681691c3183 ]

[Why]
Links which are dynamically assigned link encoders have their link
encoder set to NULL.

[How]
Check that a pointer to a link_encoder object is non-NULL before using
it.

Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agodrm/amdgpu: Fix MMIO access page fault
Andrey Grodzovsky [Thu, 16 Sep 2021 16:54:07 +0000 (12:54 -0400)]
drm/amdgpu: Fix MMIO access page fault

[ Upstream commit c03509cbc01559549700e14c4a6239f2572ab4ba ]

Add more guards to MMIO access post device
unbind/unplug

Bug: https://bugs.archlinux.org/task/72092?project=1&order=dateopened&sort=desc&pagenum=1
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: James Zhu <James.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agofscrypt: allow 256-bit master keys with AES-256-XTS
Eric Biggers [Tue, 21 Sep 2021 03:03:03 +0000 (20:03 -0700)]
fscrypt: allow 256-bit master keys with AES-256-XTS

[ Upstream commit 7f595d6a6cdc336834552069a2e0a4f6d4756ddf ]

fscrypt currently requires a 512-bit master key when AES-256-XTS is
used, since AES-256-XTS keys are 512-bit and fscrypt requires that the
master key be at least as long any key that will be derived from it.

However, this is overly strict because AES-256-XTS doesn't actually have
a 512-bit security strength, but rather 256-bit.  The fact that XTS
takes twice the expected key size is a quirk of the XTS mode.  It is
sufficient to use 256 bits of entropy for AES-256-XTS, provided that it
is first properly expanded into a 512-bit key, which HKDF-SHA512 does.

Therefore, relax the check of the master key size to use the security
strength of the derived key rather than the size of the derived key
(except for v1 encryption policies, which don't use HKDF).

Besides making things more flexible for userspace, this is needed in
order for the use of a KDF which only takes a 256-bit key to be
introduced into the fscrypt key hierarchy.  This will happen with
hardware-wrapped keys support, as all known hardware which supports that
feature uses an SP800-108 KDF using AES-256-CMAC, so the wrapped keys
are wrapped 256-bit AES keys.  Moreover, there is interest in fscrypt
supporting the same type of AES-256-CMAC based KDF in software as an
alternative to HKDF-SHA512.  There is no security problem with such
features, so fix the key length check to work properly with them.

Reviewed-by: Paul Crowley <paulcrowley@google.com>
Link: https://lore.kernel.org/r/20210921030303.5598-1-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agospi: Check we have a spi_device_id for each DT compatible
Mark Brown [Tue, 21 Sep 2021 19:21:49 +0000 (20:21 +0100)]
spi: Check we have a spi_device_id for each DT compatible

[ Upstream commit 5fa6863ba69265cb7e45567d12614790ff26bd56 ]

Currently for SPI devices we use the spi_device_id for module autoloading
even on systems using device tree, meaning that listing a compatible string
in the of_match_table isn't enough to have the module for a SPI driver
autoloaded.

We attempted to fix this by generating OF based modaliases for devices
instantiated from DT in 3ce6c9e2617e ("spi: add of_device_uevent_modalias
support") but this meant we no longer reported spi_device_id based aliases
which broke drivers such as spi-nor which don't list all the compatible
strings they support directly for DT, and in at least that case it's not
super practical to do so given the very large number of compatibles
needed, much larger than the number spi_device_ids due to vendor strings.
As a result fell back to using spi_device_id based modalises.

Try to close the gap by printing a warning when a SPI driver has a DT
compatible that won't be matched as a SPI device ID with the goal of having
drivers provide both. Given fallback compatibles this check is going to be
excessive but it should be robust which is probably more important here.

Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210921192149.50740-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agomwifiex: Properly initialize private structure on interface type changes
Jonas Dreßler [Tue, 14 Sep 2021 19:59:08 +0000 (21:59 +0200)]
mwifiex: Properly initialize private structure on interface type changes

[ Upstream commit c606008b70627a2fc485732a53cc22f0f66d0981 ]

When creating a new virtual interface in mwifiex_add_virtual_intf(), we
update our internal driver states like bss_type, bss_priority, bss_role
and bss_mode to reflect the mode the firmware will be set to.

When switching virtual interface mode using
mwifiex_init_new_priv_params() though, we currently only update bss_mode
and bss_role. In order for the interface mode switch to actually work,
we also need to update bss_type to its proper value, so do that.

This fixes a crash of the firmware (because the driver tries to execute
commands that are invalid in AP mode) when switching from station mode
to AP mode.

Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-9-verdre@v0yd.nl
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agomwifiex: Run SET_BSS_MODE when changing from P2P to STATION vif-type
Jonas Dreßler [Tue, 14 Sep 2021 19:59:03 +0000 (21:59 +0200)]
mwifiex: Run SET_BSS_MODE when changing from P2P to STATION vif-type

[ Upstream commit c2e9666cdffd347460a2b17988db4cfaf2a68fb9 ]

We currently handle changing from the P2P to the STATION virtual
interface type slightly different than changing from P2P to ADHOC: When
changing to STATION, we don't send the SET_BSS_MODE command. We do send
that command on all other type-changes though, and it probably makes
sense to send the command since after all we just changed our BSS_MODE.
Looking at prior changes to this part of the code, it seems that this is
simply a leftover from old refactorings.

Since sending the SET_BSS_MODE command is the only difference between
mwifiex_change_vif_to_sta_adhoc() and the current code, we can now use
mwifiex_change_vif_to_sta_adhoc() for both switching to ADHOC and
STATION interface type.

This does not fix any particular bug and just "looked right", so there's
a small chance it might be a regression.

Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-4-verdre@v0yd.nl
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agox86: Increase exception stack sizes
Peter Zijlstra [Wed, 15 Sep 2021 14:19:46 +0000 (16:19 +0200)]
x86: Increase exception stack sizes

[ Upstream commit 7fae4c24a2b84a66c7be399727aca11e7a888462 ]

It turns out that a single page of stack is trivial to overflow with
all the tracing gunk enabled. Raise the exception stacks to 2 pages,
which is still half the interrupt stacks, which are at 4 pages.

Reported-by: Michael Wang <yun.wang@linux.alibaba.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/YUIO9Ye98S5Eb68w@hirez.programming.kicks-ass.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agox86/mm/64: Improve stack overflow warnings
Peter Zijlstra [Wed, 15 Sep 2021 15:12:59 +0000 (17:12 +0200)]
x86/mm/64: Improve stack overflow warnings

[ Upstream commit 44b979fa302cab91bdd2cc982823e5c13202cd4e ]

Current code has an explicit check for hitting the task stack guard;
but overflowing any of the other stacks will get you a non-descript
general #DF warning.

Improve matters by using get_stack_info_noinstr() to detetrmine if and
which stack guard page got hit, enabling a better stack warning.

In specific, Michael Wang reported what turned out to be an NMI
exception stack overflow, which is now clearly reported as such:

  [] BUG: NMI stack guard page was hit at 0000000085fd977b (stack is 000000003a55b09e..00000000d8cce1a5)

Reported-by: Michael Wang <yun.wang@linux.alibaba.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Michael Wang <yun.wang@linux.alibaba.com>
Link: https://lkml.kernel.org/r/YUTE/NuqnaWbST8n@hirez.programming.kicks-ass.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agocrypto: aesni - check walk.nbytes instead of err
Shreyansh Chouhan [Sat, 11 Sep 2021 11:07:59 +0000 (16:37 +0530)]
crypto: aesni - check walk.nbytes instead of err

[ Upstream commit a2d3cbc80d2527b435154ff0f89b56ef4b84370f ]

In the code for xts_crypt(), we check for the err value returned by
skcipher_walk_virt() and return from the function if it is non zero.
However, skcipher_walk_virt() can set walk.nbytes to 0, which would cause
us to call kernel_fpu_begin(), and then skip the kernel_fpu_end() call.

This patch checks for the walk.nbytes value instead, and returns if
walk.nbytes is 0. This prevents us from calling kernel_fpu_begin() in
the first place and also covers the case of having a non zero err value
returned from skcipher_walk_virt().

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Shreyansh Chouhan <chouhan.shreyansh630@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agoath11k: Align bss_chan_info structure with firmware
Seevalamuthu Mariappan [Tue, 20 Jul 2021 21:49:22 +0000 (00:49 +0300)]
ath11k: Align bss_chan_info structure with firmware

[ Upstream commit feab5bb8f1d4621025dceae7eef62d5f92de34ac ]

pdev_id in structure 'wmi_pdev_bss_chan_info_event' is wrongly placed
at the beginning. This causes invalid values in survey dump. Hence, align
the structure with the firmware.

Note: The firmware releases follow this order since the feature was
implemented. Also, it is not changing across the branches including
QCA6390.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1

Signed-off-by: Ritesh Singh <ritesi@codeaurora.org>
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210720214922.118078-3-jouni@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agosmackfs: Fix use-after-free in netlbl_catmap_walk()
Pawan Gupta [Sun, 29 Aug 2021 06:41:40 +0000 (23:41 -0700)]
smackfs: Fix use-after-free in netlbl_catmap_walk()

[ Upstream commit 0817534ff9ea809fac1322c5c8c574be8483ea57 ]

Syzkaller reported use-after-free bug as described in [1]. The bug is
triggered when smk_set_cipso() tries to free stale category bitmaps
while there are concurrent reader(s) using the same bitmaps.

Wait for RCU grace period to finish before freeing the category bitmaps
in smk_set_cipso(). This makes sure that there are no more readers using
the stale bitmaps and freeing them should be safe.

[1] https://lore.kernel.org/netdev/000000000000a814c505ca657a4e@google.com/

Reported-by: syzbot+3f91de0b813cc3d19a80@syzkaller.appspotmail.com
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agorcu-tasks: Move RTGS_WAIT_CBS to beginning of rcu_tasks_kthread() loop
Paul E. McKenney [Wed, 11 Aug 2021 16:07:44 +0000 (09:07 -0700)]
rcu-tasks: Move RTGS_WAIT_CBS to beginning of rcu_tasks_kthread() loop

[ Upstream commit 0db7c32ad3160ae06f497d48a74bd46a2a35e6bf ]

Early in debugging, it made some sense to differentiate the first
iteration from subsequent iterations, but now this just causes confusion.
This commit therefore moves the "set_tasks_gp_state(rtp, RTGS_WAIT_CBS)"
statement to the beginning of the "for" loop in rcu_tasks_kthread().

Reported-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agoACPI: resources: Add DMI-based legacy IRQ override quirk
Hui Wang [Wed, 15 Sep 2021 13:09:05 +0000 (21:09 +0800)]
ACPI: resources: Add DMI-based legacy IRQ override quirk

[ Upstream commit 892a012699fc0b91a2ed6309078936191447f480 ]

After the commit 0ec4e55e9f57 ("ACPI: resources: Add checks for ACPI
IRQ override") is reverted, the keyboard on Medion laptops can't
work again.

To fix the keyboard issue, add a DMI-based override check that will
not affect other machines along the lines of prt_quirks[] in
drivers/acpi/pci_irq.c.

If similar issues are seen on other platforms, the quirk table could
be expanded in the future.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=213031
BugLink: http://bugs.launchpad.net/bugs/1909814
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reported-by: Manuel Krause <manuelkrause@netscape.net>
Tested-by: Manuel Krause <manuelkrause@netscape.net>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agonet: sched: update default qdisc visibility after Tx queue cnt changes
Jakub Kicinski [Mon, 13 Sep 2021 22:53:30 +0000 (15:53 -0700)]
net: sched: update default qdisc visibility after Tx queue cnt changes

[ Upstream commit 1e080f17750d1083e8a32f7b350584ae1cd7ff20 ]

mq / mqprio make the default child qdiscs visible. They only do
so for the qdiscs which are within real_num_tx_queues when the
device is registered. Depending on order of calls in the driver,
or if user space changes config via ethtool -L the number of
qdiscs visible under tc qdisc show will differ from the number
of queues. This is confusing to users and potentially to system
configuration scripts which try to make sure qdiscs have the
right parameters.

Add a new Qdisc_ops callback and make relevant qdiscs TTRT.

Note that this uncovers the "shortcut" created by
commit 1f27cde313d7 ("net: sched: use pfifo_fast for non real queues")
The default child qdiscs beyond initial real_num_tx are always
pfifo_fast, no matter what the sysfs setting is. Fixing this
gets a little tricky because we'd need to keep a reference
on whatever the default qdisc was at the time of creation.
In practice this is likely an non-issue the qdiscs likely have
to be configured to non-default settings, so whatever user space
is doing such configuration can replace the pfifos... now that
it will see them.

Reported-by: Matthew Massey <matthewmassey@fb.com>
Reviewed-by: Dave Taht <dave.taht@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agolocking/lockdep: Avoid RCU-induced noinstr fail
Peter Zijlstra [Thu, 24 Jun 2021 09:41:10 +0000 (11:41 +0200)]
locking/lockdep: Avoid RCU-induced noinstr fail

[ Upstream commit ce0b9c805dd66d5e49fd53ec5415ae398f4c56e6 ]

vmlinux.o: warning: objtool: look_up_lock_class()+0xc7: call to rcu_read_lock_any_held() leaves .noinstr.text section

Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20210624095148.311980536@infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agoMIPS: lantiq: dma: reset correct number of channel
Aleksander Jan Bajkowski [Tue, 14 Sep 2021 21:20:59 +0000 (23:20 +0200)]
MIPS: lantiq: dma: reset correct number of channel

[ Upstream commit 5ca9ce2ba4d5884cd94d1a856c675ab1242cd242 ]

Different SoCs have a different number of channels, e.g .:
* amazon-se has 10 channels,
* danube+ar9 have 20 channels,
* vr9 has 28 channels,
* ar10 has 24 channels.

We can read the ID register and, depending on the reported
number of channels, reset the appropriate number of channels.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agoMIPS: lantiq: dma: add small delay after reset
Aleksander Jan Bajkowski [Tue, 14 Sep 2021 21:20:58 +0000 (23:20 +0200)]
MIPS: lantiq: dma: add small delay after reset

[ Upstream commit c12aa581f6d5e80c3c3675ab26a52c2b3b62f76e ]

Reading the DMA registers immediately after the reset causes
Data Bus Error. Adding a small delay fixes this issue.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agodrm/amdgpu: move iommu_resume before ip init/resume
James Zhu [Tue, 7 Sep 2021 15:32:22 +0000 (11:32 -0400)]
drm/amdgpu: move iommu_resume before ip init/resume

[ Upstream commit 9cec53c18a3170c7e5673c414da56aeecee94832 ]

Separate iommu_resume from kfd_resume, and move it before
other amdgpu ip init/resume.

Bug: https://bugzilla.kernel.org/show_bug.cgi?id=211277
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agoplatform/x86: wmi: do not fail if disabling fails
Barnabás Pőcze [Sat, 4 Sep 2021 17:56:26 +0000 (17:56 +0000)]
platform/x86: wmi: do not fail if disabling fails

[ Upstream commit 1975718c488a39128f1f515b23ae61a5a214cc3d ]

Previously, `__query_block()` would fail if the
second WCxx method call failed. However, the
WQxx method might have succeeded, and potentially
allocated memory for the result. Instead of
throwing away the result and potentially
leaking memory, ignore the result of
the second WCxx call.

Signed-off-by: Barnabás Pőcze <pobrn@protonmail.com>
Link: https://lore.kernel.org/r/20210904175450.156801-25-pobrn@protonmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agorcutorture: Avoid problematic critical section nesting on PREEMPT_RT
Scott Wood [Fri, 20 Aug 2021 07:42:36 +0000 (09:42 +0200)]
rcutorture: Avoid problematic critical section nesting on PREEMPT_RT

[ Upstream commit 71921a9606ddbcc1d98c00eca7ae82c373d1fecd ]

rcutorture is generating some nesting scenarios that are not compatible on PREEMPT_RT.
For example:
preempt_disable();
rcu_read_lock_bh();
preempt_enable();
rcu_read_unlock_bh();

The problem here is that on PREEMPT_RT the bottom halves have to be
disabled and enabled in preemptible context.

Reorder locking: start with BH locking and continue with then with
disabling preemption or interrupts. In the unlocking do it reverse by
first enabling interrupts and preemption and BH at the very end.
Ensure that on PREEMPT_RT BH locking remains unchanged if in
non-preemptible context.

Link: https://lkml.kernel.org/r/20190911165729.11178-6-swood@redhat.com
Link: https://lkml.kernel.org/r/20210819182035.GF4126399@paulmck-ThinkPad-P17-Gen-1
Signed-off-by: Scott Wood <swood@redhat.com>
[bigeasy: Drop ATOM_BH, make it only about changing BH in atomic
context. Allow enabling RCU in IRQ-off section. Reword commit message.]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agodrm/panel-orientation-quirks: add Valve Steam Deck
Simon Ser [Sat, 11 Sep 2021 10:24:40 +0000 (10:24 +0000)]
drm/panel-orientation-quirks: add Valve Steam Deck

[ Upstream commit 9eeb7b4e40bfd69d8aaa920c7e9df751c9e11dce ]

Valve's Steam Deck has a 800x1280 LCD screen.

Signed-off-by: Simon Ser <contact@emersion.fr>
Cc: Jared Baldridge <jrb@expunge.us>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Hans de Goede <hdegoede@redhat.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210911102430.253986-1-contact@emersion.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agoBluetooth: call sock_hold earlier in sco_conn_del
Desmond Cheong Zhi Xi [Fri, 3 Sep 2021 03:13:05 +0000 (23:13 -0400)]
Bluetooth: call sock_hold earlier in sco_conn_del

[ Upstream commit f4712fa993f688d0a48e0c28728fcdeb88c1ea58 ]

In sco_conn_del, conn->sk is read while holding on to the
sco_conn.lock to avoid races with a socket that could be released
concurrently.

However, in between unlocking sco_conn.lock and calling sock_hold,
it's possible for the socket to be freed, which would cause a
use-after-free write when sock_hold is finally called.

To fix this, the reference count of the socket should be increased
while the sco_conn.lock is still held.

Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agoBluetooth: fix use-after-free error in lock_sock_nested()
Wang ShaoBo [Wed, 1 Sep 2021 00:35:37 +0000 (17:35 -0700)]
Bluetooth: fix use-after-free error in lock_sock_nested()

[ Upstream commit 1bff51ea59a9afb67d2dd78518ab0582a54a472c ]

use-after-free error in lock_sock_nested is reported:

[  179.140137][ T3731] =====================================================
[  179.142675][ T3731] BUG: KMSAN: use-after-free in lock_sock_nested+0x280/0x2c0
[  179.145494][ T3731] CPU: 4 PID: 3731 Comm: kworker/4:2 Not tainted 5.12.0-rc6+ #54
[  179.148432][ T3731] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
[  179.151806][ T3731] Workqueue: events l2cap_chan_timeout
[  179.152730][ T3731] Call Trace:
[  179.153301][ T3731]  dump_stack+0x24c/0x2e0
[  179.154063][ T3731]  kmsan_report+0xfb/0x1e0
[  179.154855][ T3731]  __msan_warning+0x5c/0xa0
[  179.155579][ T3731]  lock_sock_nested+0x280/0x2c0
[  179.156436][ T3731]  ? kmsan_get_metadata+0x116/0x180
[  179.157257][ T3731]  l2cap_sock_teardown_cb+0xb8/0x890
[  179.158154][ T3731]  ? __msan_metadata_ptr_for_load_8+0x10/0x20
[  179.159141][ T3731]  ? kmsan_get_metadata+0x116/0x180
[  179.159994][ T3731]  ? kmsan_get_shadow_origin_ptr+0x84/0xb0
[  179.160959][ T3731]  ? l2cap_sock_recv_cb+0x420/0x420
[  179.161834][ T3731]  l2cap_chan_del+0x3e1/0x1d50
[  179.162608][ T3731]  ? kmsan_get_metadata+0x116/0x180
[  179.163435][ T3731]  ? kmsan_get_shadow_origin_ptr+0x84/0xb0
[  179.164406][ T3731]  l2cap_chan_close+0xeea/0x1050
[  179.165189][ T3731]  ? kmsan_internal_unpoison_shadow+0x42/0x70
[  179.166180][ T3731]  l2cap_chan_timeout+0x1da/0x590
[  179.167066][ T3731]  ? __msan_metadata_ptr_for_load_8+0x10/0x20
[  179.168023][ T3731]  ? l2cap_chan_create+0x560/0x560
[  179.168818][ T3731]  process_one_work+0x121d/0x1ff0
[  179.169598][ T3731]  worker_thread+0x121b/0x2370
[  179.170346][ T3731]  kthread+0x4ef/0x610
[  179.171010][ T3731]  ? process_one_work+0x1ff0/0x1ff0
[  179.171828][ T3731]  ? kthread_blkcg+0x110/0x110
[  179.172587][ T3731]  ret_from_fork+0x1f/0x30
[  179.173348][ T3731]
[  179.173752][ T3731] Uninit was created at:
[  179.174409][ T3731]  kmsan_internal_poison_shadow+0x5c/0xf0
[  179.175373][ T3731]  kmsan_slab_free+0x76/0xc0
[  179.176060][ T3731]  kfree+0x3a5/0x1180
[  179.176664][ T3731]  __sk_destruct+0x8af/0xb80
[  179.177375][ T3731]  __sk_free+0x812/0x8c0
[  179.178032][ T3731]  sk_free+0x97/0x130
[  179.178686][ T3731]  l2cap_sock_release+0x3d5/0x4d0
[  179.179457][ T3731]  sock_close+0x150/0x450
[  179.180117][ T3731]  __fput+0x6bd/0xf00
[  179.180787][ T3731]  ____fput+0x37/0x40
[  179.181481][ T3731]  task_work_run+0x140/0x280
[  179.182219][ T3731]  do_exit+0xe51/0x3e60
[  179.182930][ T3731]  do_group_exit+0x20e/0x450
[  179.183656][ T3731]  get_signal+0x2dfb/0x38f0
[  179.184344][ T3731]  arch_do_signal_or_restart+0xaa/0xe10
[  179.185266][ T3731]  exit_to_user_mode_prepare+0x2d2/0x560
[  179.186136][ T3731]  syscall_exit_to_user_mode+0x35/0x60
[  179.186984][ T3731]  do_syscall_64+0xc5/0x140
[  179.187681][ T3731]  entry_SYSCALL_64_after_hwframe+0x44/0xae
[  179.188604][ T3731] =====================================================

In our case, there are two Thread A and B:

Context: Thread A:              Context: Thread B:

l2cap_chan_timeout()            __se_sys_shutdown()
  l2cap_chan_close()              l2cap_sock_shutdown()
    l2cap_chan_del()                l2cap_chan_close()
      l2cap_sock_teardown_cb()        l2cap_sock_teardown_cb()

Once l2cap_sock_teardown_cb() excuted, this sock will be marked as SOCK_ZAPPED,
and can be treated as killable in l2cap_sock_kill() if sock_orphan() has
excuted, at this time we close sock through sock_close() which end to call
l2cap_sock_kill() like Thread C:

Context: Thread C:

sock_close()
  l2cap_sock_release()
    sock_orphan()
    l2cap_sock_kill()  #free sock if refcnt is 1

If C completed, Once A or B reaches l2cap_sock_teardown_cb() again,
use-after-free happened.

We should set chan->data to NULL if sock is destructed, for telling teardown
operation is not allowed in l2cap_sock_teardown_cb(), and also we should
avoid killing an already killed socket in l2cap_sock_close_cb().

Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agoBluetooth: sco: Fix lock_sock() blockage by memcpy_from_msg()
Takashi Iwai [Sat, 28 Aug 2021 16:18:18 +0000 (18:18 +0200)]
Bluetooth: sco: Fix lock_sock() blockage by memcpy_from_msg()

[ Upstream commit 99c23da0eed4fd20cae8243f2b51e10e66aa0951 ]

The sco_send_frame() also takes lock_sock() during memcpy_from_msg()
call that may be endlessly blocked by a task with userfaultd
technique, and this will result in a hung task watchdog trigger.

Just like the similar fix for hci_sock_sendmsg() in commit
92c685dc5de0 ("Bluetooth: reorganize functions..."), this patch moves
the  memcpy_from_msg() out of lock_sock() for addressing the hang.

This should be the last piece for fixing CVE-2021-3640 after a few
already queued fixes.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agodrm: panel-orientation-quirks: Add quirk for the Samsung Galaxy Book 10.6
Hans de Goede [Sun, 30 May 2021 11:04:27 +0000 (13:04 +0200)]
drm: panel-orientation-quirks: Add quirk for the Samsung Galaxy Book 10.6

[ Upstream commit 88fa1fde918951c175ae5ea0f31efc4bb1736ab9 ]

The Samsung Galaxy Book 10.6 uses a panel which has been mounted
90 degrees rotated. Add a quirk for this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Ser <contact@emersion.fr>
Link: https://patchwork.freedesktop.org/patch/msgid/20210530110428.12994-4-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agodrm: panel-orientation-quirks: Add quirk for KD Kurio Smart C15200 2-in-1
Hans de Goede [Sun, 30 May 2021 11:04:26 +0000 (13:04 +0200)]
drm: panel-orientation-quirks: Add quirk for KD Kurio Smart C15200 2-in-1

[ Upstream commit a53f1dd3ab9fec715c6c2e8e01bf4d3c07eef8e5 ]

The KD Kurio Smart C15200 2-in-1 uses  a panel which has been mounted 90
degrees rotated. Add a quirk for this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Ser <contact@emersion.fr>
Link: https://patchwork.freedesktop.org/patch/msgid/20210530110428.12994-3-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agodrm: panel-orientation-quirks: Update the Lenovo Ideapad D330 quirk (v2)
Hans de Goede [Sun, 30 May 2021 11:04:25 +0000 (13:04 +0200)]
drm: panel-orientation-quirks: Update the Lenovo Ideapad D330 quirk (v2)

[ Upstream commit 820a2ab23d5eab4ccfb82581eda8ad4acf18458f ]

2 improvements to the Lenovo Ideapad D330 panel-orientation quirks:

1. Some versions of the Lenovo Ideapad D330 have a DMI_PRODUCT_NAME of
"81H3" and others have "81MD". Testing has shown that the "81MD" also has
a 90 degree mounted panel. Drop the DMI_PRODUCT_NAME from the existing
quirk so that the existing quirk matches both variants.

2. Some of the Lenovo Ideapad D330 models have a HD (800x1280) screen
instead of a FHD (1200x1920) screen (both are mounted right-side-up) add
a second Lenovo Ideapad D330 quirk for the HD version.

Changes in v2:
- Add a new quirk for Lenovo Ideapad D330 models with a HD screen instead
  of a FHD screen

Link: https://github.com/systemd/systemd/pull/18884
Acked-by: Simon Ser <contact@emersion.fr>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210530110428.12994-2-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agodma-buf: WARN on dmabuf release with pending attachments
Charan Teja Reddy [Fri, 23 Jul 2021 12:31:08 +0000 (18:01 +0530)]
dma-buf: WARN on dmabuf release with pending attachments

[ Upstream commit f492283b157053e9555787262f058ae33096f568 ]

It is expected from the clients to follow the below steps on an imported
dmabuf fd:
a) dmabuf = dma_buf_get(fd) // Get the dmabuf from fd
b) dma_buf_attach(dmabuf); // Clients attach to the dmabuf
   o Here the kernel does some slab allocations, say for
dma_buf_attachment and may be some other slab allocation in the
dmabuf->ops->attach().
c) Client may need to do dma_buf_map_attachment().
d) Accordingly dma_buf_unmap_attachment() should be called.
e) dma_buf_detach () // Clients detach to the dmabuf.
   o Here the slab allocations made in b) are freed.
f) dma_buf_put(dmabuf) // Can free the dmabuf if it is the last
reference.

Now say an erroneous client failed at step c) above thus it directly
called dma_buf_put(), step f) above. Considering that it may be the last
reference to the dmabuf, buffer will be freed with pending attachments
left to the dmabuf which can show up as the 'memory leak'. This should
at least be reported as the WARN().

Signed-off-by: Charan Teja Reddy <charante@codeaurora.org>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1627043468-16381-1-git-send-email-charante@codeaurora.org
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
2 years agocomponent: do not leave master devres group open after bind
Kai Vehmanen [Wed, 13 Oct 2021 16:13:45 +0000 (19:13 +0300)]
component: do not leave master devres group open after bind

commit c87761db2100677a69be551365105125d872af5b upstream.

In current code, the devres group for aggregate master is left open
after call to component_master_add_*(). This leads to problems when the
master does further managed allocations on its own. When any
participating driver calls component_del(), this leads to immediate
release of resources.

This came up when investigating a page fault occurring with i915 DRM
driver unbind with 5.15-rc1 kernel. The following sequence occurs:

 i915_pci_remove()
   -> intel_display_driver_unregister()
     -> i915_audio_component_cleanup()
       -> component_del()
         -> component.c:take_down_master()
           -> hdac_component_master_unbind() [via master->ops->unbind()]
           -> devres_release_group(master->parent, NULL)

With older kernels this has not caused issues, but with audio driver
moving to use managed interfaces for more of its allocations, this no
longer works. Devres log shows following to occur:

component_master_add_with_match()
[  126.886032] snd_hda_intel 0000:00:1f.3: DEVRES ADD 00000000323ccdc5 devm_component_match_release (24 bytes)
[  126.886045] snd_hda_intel 0000:00:1f.3: DEVRES ADD 00000000865cdb29 grp< (0 bytes)
[  126.886049] snd_hda_intel 0000:00:1f.3: DEVRES ADD 000000001b480725 grp< (0 bytes)

audio driver completes its PCI probe()
[  126.892238] snd_hda_intel 0000:00:1f.3: DEVRES ADD 000000001b480725 pcim_iomap_release (48 bytes)

component_del() called() at DRM/i915 unbind()
[  137.579422] i915 0000:00:02.0: DEVRES REL 00000000ef44c293 grp< (0 bytes)
[  137.579445] snd_hda_intel 0000:00:1f.3: DEVRES REL 00000000865cdb29 grp< (0 bytes)
[  137.579458] snd_hda_intel 0000:00:1f.3: DEVRES REL 000000001b480725 pcim_iomap_release (48 bytes)

So the "devres_release_group(master->parent, NULL)" ends up freeing the
pcim_iomap allocation. Upon next runtime resume, the audio driver will
cause a page fault as the iomap alloc was released without the driver
knowing about it.

Fix this issue by using the "struct master" pointer as identifier for
the devres group, and by closing the devres group after
the master->ops->bind() call is done. This allows devres allocations
done by the driver acting as master to be isolated from the binding state
of the aggregate driver. This modifies the logic originally introduced in
commit 9e1ccb4a7700 ("drivers/base: fix devres handling for master device")

Fixes: 9e1ccb4a7700 ("drivers/base: fix devres handling for master device")
Cc: stable@vger.kernel.org
Acked-by: Imre Deak <imre.deak@intel.com>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
BugLink: https://gitlab.freedesktop.org/drm/intel/-/issues/4136
Link: https://lore.kernel.org/r/20211013161345.3755341-1-kai.vehmanen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2 years agopower: supply: max17042_battery: Clear status bits in interrupt handler
Sebastian Krzyszkowiak [Tue, 14 Sep 2021 12:18:05 +0000 (14:18 +0200)]
power: supply: max17042_battery: Clear status bits in interrupt handler

commit 0cf48167b87e388fa1268c9fe6d2443ae7f43d8a upstream.

The gauge requires us to clear the status bits manually for some alerts
to be properly dismissed. Previously the IRQ was configured to react only
on falling edge, which wasn't technically correct (the ALRT line is active
low), but it had a happy side-effect of preventing interrupt storms
on uncleared alerts from happening.

Fixes: 7fbf6b731bca ("power: supply: max17042: Do not enforce (incorrect) interrupt trigger type")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2 years agoUSB: chipidea: fix interrupt deadlock
Johan Hovold [Thu, 21 Oct 2021 08:34:47 +0000 (10:34 +0200)]
USB: chipidea: fix interrupt deadlock

commit 9aaa81c3366e8393a62374e3a1c67c69edc07b8a upstream.

Chipidea core was calling the interrupt handler from non-IRQ context
with interrupts enabled, something which can lead to a deadlock if
there's an actual interrupt trying to take a lock that's already held
(e.g. the controller lock in udc_irq()).

Add a wrapper that can be used to fake interrupts instead of calling the
handler directly.

Fixes: 3ecb3e09b042 ("usb: chipidea: Use extcon framework for VBUS and ID detect")
Fixes: 876d4e1e8298 ("usb: chipidea: core: add wakeup support for extcon")
Cc: Peter Chen <peter.chen@kernel.org>
Cc: stable@vger.kernel.org # 4.4
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211021083447.20078-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2 years agoUSB: iowarrior: fix control-message timeouts
Johan Hovold [Mon, 25 Oct 2021 11:51:59 +0000 (13:51 +0200)]
USB: iowarrior: fix control-message timeouts

commit 79a4479a17b83310deb0b1a2a274fe5be12d2318 upstream.

USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.

Use the common control-message timeout define for the five-second
timeout and drop the driver-specific one.

Fixes: 946b960d13c1 ("USB: add driver for iowarrior devices.")
Cc: stable@vger.kernel.org # 2.6.21
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211025115159.4954-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2 years agomost: fix control-message timeouts
Johan Hovold [Mon, 25 Oct 2021 11:58:11 +0000 (13:58 +0200)]
most: fix control-message timeouts

commit 63b3e810eff65fb8587fcb26fa0b56802be12dcf upstream.

USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.

Use the common control-message timeout defines for the five-second
timeouts.

Fixes: 97a6f772f36b ("drivers: most: add USB adapter driver")
Cc: stable@vger.kernel.org # 5.9
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211025115811.5410-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2 years agoRevert "serial: 8250: Fix reporting real baudrate value in c_ospeed field"
Johan Hovold [Thu, 7 Oct 2021 13:31:46 +0000 (15:31 +0200)]
Revert "serial: 8250: Fix reporting real baudrate value in c_ospeed field"

commit d02b006b29de14968ba4afa998bede0d55469e29 upstream.

This reverts commit 32262e2e429cdb31f9e957e997d53458762931b7.

The commit in question claims to determine the inverse of
serial8250_get_divisor() but failed to notice that some drivers override
the default implementation using a get_divisor() callback.

This means that the computed line-speed values can be completely wrong
and results in regular TCSETS requests failing (the incorrect values
would also be passed to any overridden set_divisor() callback).

Similarly, it also failed to honour the old (deprecated) ASYNC_SPD_FLAGS
and would break applications relying on those when re-encoding the
actual line speed.

There are also at least two quirks, UART_BUG_QUOT and an OMAP1510
workaround, which were happily ignored and that are now broken.

Finally, even if the offending commit were to be implemented correctly,
this is a new feature and not something which should be backported to
stable.

Cc: Pali Rohár <pali@kernel.org>
Fixes: 32262e2e429c ("serial: 8250: Fix reporting real baudrate value in c_ospeed field")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211007133146.28949-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2 years agoserial: 8250: Fix reporting real baudrate value in c_ospeed field
Pali Rohár [Mon, 27 Sep 2021 09:37:04 +0000 (11:37 +0200)]
serial: 8250: Fix reporting real baudrate value in c_ospeed field

commit 32262e2e429cdb31f9e957e997d53458762931b7 upstream.

In most cases it is not possible to set exact baudrate value to hardware.

So fix reporting real baudrate value which was set to hardware via c_ospeed
termios field. It can be retrieved by ioctl(TCGETS2) from userspace.

Real baudrate value is calculated from chosen hardware divisor and base
clock. It is implemented in a new function serial8250_compute_baud_rate()
which is inverse of serial8250_get_divisor() function.

With this change is fixed also UART timeout value (it is updated via
uart_update_timeout() function), which is calculated from the now fixed
baudrate value too.

Cc: stable@vger.kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20210927093704.19768-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2 years agoio-wq: serialize hash clear with wakeup
Jens Axboe [Fri, 12 Nov 2021 00:32:53 +0000 (17:32 -0700)]
io-wq: serialize hash clear with wakeup

commit d3e3c102d107bb84251455a298cf475f24bab995 upstream.

We need to ensure that we serialize the stalled and hash bits with the
wait_queue wait handler, or we could be racing with someone modifying
the hashed state after we find it busy, but before we then give up and
wait for it to be cleared. This can cause random delays or stalls when
handling buffered writes for many files, where some of these files cause
hash collisions between the worker threads.

Cc: stable@vger.kernel.org
Reported-by: Daniel Black <daniel@mariadb.org>
Fixes: e941894eae31 ("io-wq: make buffered file write hashed work map per-ctx")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2 years agoksmbd: set unique value to volume serial field in FS_VOLUME_INFORMATION
Namjae Jeon [Sun, 31 Oct 2021 00:53:50 +0000 (09:53 +0900)]
ksmbd: set unique value to volume serial field in FS_VOLUME_INFORMATION

commit 5d2f0b1083eb158bdff01dd557e2c25046c0a7d2 upstream.

Steve French reported ksmbd set fixed value to volume serial field in
FS_VOLUME_INFORMATION. Volume serial value needs to be set to a unique
value for client fscache. This patch set crc value that is generated
with share name, path name and netbios name to volume serial.

Fixes: e2f34481b24d ("cifsd: add server-side procedures for SMB3")
Cc: stable@vger.kernel.org # v5.15
Reported-by: Steve French <smfrench@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2 years agoserial: 8250: fix racy uartclk update
Johan Hovold [Fri, 15 Oct 2021 11:14:20 +0000 (13:14 +0200)]
serial: 8250: fix racy uartclk update

commit 211cde4f5817dc88ef7f8f2fa286e57fbf14c8ee upstream.

Commit 868f3ee6e452 ("serial: 8250: Add 8250 port clock update method")
added a hack to support SoCs where the UART reference clock can
change behind the back of the driver but failed to add the proper
locking.

First, make sure to take a reference to the tty struct to avoid
dereferencing a NULL pointer if the clock change races with a hangup.

Second, the termios semaphore must be held during the update to prevent
a racing termios change.

Fixes: 868f3ee6e452 ("serial: 8250: Add 8250 port clock update method")
Fixes: c8dff3aa8241 ("serial: 8250: Skip uninitialized TTY port baud rate update")
Cc: stable@vger.kernel.org # 5.9
Cc: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211015111422.1027-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2 years agoUSB: serial: keyspan: fix memleak on probe errors
Wang Hai [Fri, 15 Oct 2021 08:55:43 +0000 (16:55 +0800)]
USB: serial: keyspan: fix memleak on probe errors

commit 910c996335c37552ee30fcb837375b808bb4f33b upstream.

I got memory leak as follows when doing fault injection test:

unreferenced object 0xffff888258228440 (size 64):
  comm "kworker/7:2", pid 2005, jiffies 4294989509 (age 824.540s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<ffffffff8167939c>] slab_post_alloc_hook+0x9c/0x490
    [<ffffffff8167f627>] kmem_cache_alloc_trace+0x1f7/0x470
    [<ffffffffa02ac0e4>] keyspan_port_probe+0xa4/0x5d0 [keyspan]
    [<ffffffffa0294c07>] usb_serial_device_probe+0x97/0x1d0 [usbserial]
    [<ffffffff82b50ca7>] really_probe+0x167/0x460
    [<ffffffff82b51099>] __driver_probe_device+0xf9/0x180
    [<ffffffff82b51173>] driver_probe_device+0x53/0x130
    [<ffffffff82b516f5>] __device_attach_driver+0x105/0x130
    [<ffffffff82b4cfe9>] bus_for_each_drv+0x129/0x190
    [<ffffffff82b50a69>] __device_attach+0x1c9/0x270
    [<ffffffff82b518d0>] device_initial_probe+0x20/0x30
    [<ffffffff82b4f062>] bus_probe_device+0x142/0x160
    [<ffffffff82b4a4e9>] device_add+0x829/0x1300
    [<ffffffffa0295fda>] usb_serial_probe.cold+0xc9b/0x14ac [usbserial]
    [<ffffffffa02266aa>] usb_probe_interface+0x1aa/0x3c0 [usbcore]
    [<ffffffff82b50ca7>] really_probe+0x167/0x460

If keyspan_port_probe() fails to allocate memory for an out_buffer[i] or
in_buffer[i], the previously allocated memory for out_buffer or
in_buffer needs to be freed on the error handling path, otherwise a
memory leak will result.

Fixes: bad41a5bf177 ("USB: keyspan: fix port DMA-buffer allocations")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Link: https://lore.kernel.org/r/20211015085543.1203011-1-wanghai38@huawei.com
Cc: stable@vger.kernel.org # 3.12
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2 years agoDocumentation:devicetree:bindings:iio:dac: Fix val
Mihail Chindris [Thu, 7 Oct 2021 08:00:36 +0000 (08:00 +0000)]
Documentation:devicetree:bindings:iio:dac: Fix val

commit 8fc4f038fa832ec3543907fdcbe1334e1b0a8950 upstream.

A correct value for output-range-microvolts is -5 to 5 Volts
not -5 to 5 milivolts

Fixes: e904cc899293f ("dt-bindings: iio: dac: AD5766 yaml documentation")
Signed-off-by: Mihail Chindris <mihail.chindris@analog.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20211007080035.2531-6-mihail.chindris@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2 years agoiio: ad5770r: make devicetree property reading consistent
Nuno Sá [Wed, 18 Aug 2021 08:05:25 +0000 (10:05 +0200)]
iio: ad5770r: make devicetree property reading consistent

commit 26df977a909f818b7d346b3990735513e7e0bf93 upstream.

The bindings file for this driver is defining the property as 'reg' but
the driver was reading it with the 'num' name. The bindings actually had
the 'num' property when added in
commit ea52c21268e6 ("dt-bindings: iio: dac: Add docs for AD5770R DAC")
and then changed it to 'reg' in
commit 2cf3818f18b2 ("dt-bindings: iio: dac: AD5570R fix bindings errors").
However, both these commits landed in v5.7 so the assumption is
that either 'num' is not being used or if it is, the validations were not
done.

Anyways, if someone comes back yelling about this, we might just support
both of the properties in the future. Not ideal, but that's life...

Fixes: 2cf3818f18b2 ("dt-bindings: iio: dac: AD5570R fix bindings errors")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210818080525.62790-1-nuno.sa@analog.com
Cc: Stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2 years agoiio: dac: ad5446: Fix ad5622_write() return value
Pekka Korpinen [Wed, 29 Sep 2021 18:57:55 +0000 (21:57 +0300)]
iio: dac: ad5446: Fix ad5622_write() return value

commit 558df982d4ead9cac628153d0d7b60feae05ddc8 upstream.

On success i2c_master_send() returns the number of bytes written. The
call from iio_write_channel_info(), however, expects the return value to
be zero on success.

This bug causes incorrect consumption of the sysfs buffer in
iio_write_channel_info(). When writing more than two characters to
out_voltage0_raw, the ad5446 write handler is called multiple times
causing unexpected behavior.

Fixes: 3ec36a2cf0d5 ("iio:ad5446: Add support for I2C based DACs")
Signed-off-by: Pekka Korpinen <pekka.korpinen@iki.fi>
Link: https://lore.kernel.org/r/20210929185755.2384-1-pekka.korpinen@iki.fi
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2 years agodrivers: iio: dac: ad5766: Fix dt property name
Mihail Chindris [Thu, 7 Oct 2021 08:00:34 +0000 (08:00 +0000)]
drivers: iio: dac: ad5766: Fix dt property name

commit d9de0fbdeb0103a204055efb69cb5cc8f5f12a6a upstream.

In the documentation the name for the property is
output-range-microvolts which is a standard name, therefore this name
must be used.

Fixes: fd9373e41b9ba ("iio: dac: ad5766: add driver support for AD5766")
Signed-off-by: Mihail Chindris <mihail.chindris@analog.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20211007080035.2531-5-mihail.chindris@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2 years agoiio: buffer: Fix memory leak in iio_buffer_register_legacy_sysfs_groups()
Yang Yingliang [Wed, 13 Oct 2021 14:42:42 +0000 (22:42 +0800)]
iio: buffer: Fix memory leak in iio_buffer_register_legacy_sysfs_groups()

commit 604faf9a2ecd1addcc0c10a47e5aaef3c4d4fd6b upstream.

If the second iio_device_register_sysfs_group() fails,
'legacy_buffer_group.attrs' need be freed too or it will
cause memory leak:

unreferenced object 0xffff888003618280 (size 64):
  comm "xrun", pid 357, jiffies 4294907259 (age 22.296s)
  hex dump (first 32 bytes):
    80 f6 8c 03 80 88 ff ff 80 fb 8c 03 80 88 ff ff  ................
    00 f9 8c 03 80 88 ff ff 80 fc 8c 03 80 88 ff ff  ................
  backtrace:
    [<00000000076bfd43>] __kmalloc+0x1a3/0x2f0
    [<00000000c32e4886>] iio_buffers_alloc_sysfs_and_mask+0xc31/0x1290 [industrialio]

Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: d9a625744ed0 ("iio: core: merge buffer/ & scan_elements/ attributes")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211013144242.1685060-1-yangyingliang@huawei.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2 years agoiio: buffer: Fix memory leak in __iio_buffer_alloc_sysfs_and_mask()
Yang Yingliang [Wed, 13 Oct 2021 09:43:43 +0000 (17:43 +0800)]
iio: buffer: Fix memory leak in __iio_buffer_alloc_sysfs_and_mask()

commit 9a2ff8009e53296e47de72d5af0bc31cd53274ff upstream.

When iio_buffer_wrap_attr() returns NULL or buffer->buffer_group.name alloc
fails, the 'attr' which is allocated in __iio_buffer_alloc_sysfs_and_mask()
is not freed, and cause memory leak.

unreferenced object 0xffff888014882a00 (size 64):
  comm "i2c-adjd_s311-8", pid 424, jiffies 4294907737 (age 44.396s)
  hex dump (first 32 bytes):
    00 0f 8a 15 80 88 ff ff 00 0e 8a 15 80 88 ff ff  ................
    80 04 8a 15 80 88 ff ff 80 05 8a 15 80 88 ff ff  ................
  backtrace:
    [<0000000021752e67>] __kmalloc+0x1af/0x3c0
    [<0000000043e8305c>] iio_buffers_alloc_sysfs_and_mask+0xe73/0x1570 [industrialio]
    [<00000000b7aa5a17>] __iio_device_register+0x483/0x1a30 [industrialio]
    [<000000003fa0fb2f>] __devm_iio_device_register+0x23/0x90 [industrialio]
    [<000000003ab040cf>] adjd_s311_probe+0x19c/0x200 [adjd_s311]
    [<0000000080458969>] i2c_device_probe+0xa31/0xbe0
    [<00000000e20678ad>] really_probe+0x299/0xc30
    [<000000006bea9b27>] __driver_probe_device+0x357/0x500
    [<00000000e1df10d4>] driver_probe_device+0x4e/0x140
    [<0000000003661beb>] __device_attach_driver+0x257/0x340
    [<000000005bb4aa26>] bus_for_each_drv+0x166/0x1e0
    [<00000000272c5236>] __device_attach+0x272/0x420
    [<00000000d52a96ae>] bus_probe_device+0x1eb/0x2a0
    [<00000000129f7737>] device_add+0xbf0/0x1f90
    [<000000005eed4e52>] i2c_new_client_device+0x622/0xb20
    [<00000000b85a9c43>] new_device_store+0x1fa/0x420

This patch fix to free it before the error return.

Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 15097c7a1adc ("iio: buffer: wrap all buffer attributes into iio_dev_attr")
Fixes: d9a625744ed0 ("iio: core: merge buffer/ & scan_elements/ attributes")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211013094343.315275-1-yangyingliang@huawei.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2 years agoiio: buffer: Fix memory leak in iio_buffers_alloc_sysfs_and_mask()
Yang Yingliang [Mon, 18 Oct 2021 06:37:18 +0000 (14:37 +0800)]
iio: buffer: Fix memory leak in iio_buffers_alloc_sysfs_and_mask()

commit 486a25084155bf633768c26f022201c051d6fd95 upstream.

When 'iio_dev_opaque->buffer_ioctl_handler' alloc fails in
iio_buffers_alloc_sysfs_and_mask(), the 'attrs' allocated in
iio_buffer_register_legacy_sysfs_groups() will be leaked:

unreferenced object 0xffff888108568d00 (size 128):
  comm "88", pid 2014, jiffies 4294963294 (age 26.920s)
  hex dump (first 32 bytes):
    80 3e da 02 80 88 ff ff 00 3a da 02 80 88 ff ff  .>.......:......
    00 35 da 02 80 88 ff ff 00 38 da 02 80 88 ff ff  .5.......8......
  backtrace:
    [<0000000095a9e51e>] __kmalloc+0x1a3/0x2f0
    [<00000000faa3735e>] iio_buffers_alloc_sysfs_and_mask+0xfa3/0x1480 [industrialio]
    [<00000000a46384dc>] __iio_device_register+0x52e/0x1b40 [industrialio]
    [<00000000210af05e>] __devm_iio_device_register+0x22/0x80 [industrialio]
    [<00000000730d7b41>] adjd_s311_probe+0x195/0x200 [adjd_s311]
    [<00000000c0f70eb9>] i2c_device_probe+0xa07/0xbb0

The iio_buffer_register_legacy_sysfs_groups() is
called in __iio_buffer_alloc_sysfs_and_mask(),
so move the iio_buffer_unregister_legacy_sysfs_groups()
into __iio_buffer_free_sysfs_and_mask(), then the memory
will be freed.

Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: d9a625744ed0 ("iio: core: merge buffer/ & scan_elements/ attributes")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211018063718.1971240-1-yangyingliang@huawei.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>