ARM: dts: bcm2711-rpi-4-b: Add cts pin setting for bluetooth uart

This patch is referred to bcm2710-rpi-3-b-plus.dts.

The below is its commit-msg:
There is missing cts pin for uart0 used by bluetooth. Add the cts pin
setting as like bcm2837-rpi-3-b-plus.

Change-Id: I3e206b00145c24ddc86ad9dc57bef6f683622285
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>

rpi4: boot: Enable u-boot booting

Use u-boot for booting, enable u-boot.

Change-Id: I0c82be9e06b3d74a091f730ee3339a50582debe8
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>

rpi4: boot: Update the firmwares for kernel v4.19.81

Update the firmwares with the latest version from the vendor git repo.

The commit base is "b79618b5db4 kernel: Bump to 4.19.81"

Change-Id: Ica3af05ac507e3834a013d135149542723218cba
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>

packaging: Change the kernel version of the spec file

This patch changes the kernel version of the spec file to 4.19.81.

Change-Id: Ic7789806d6418ba0cf66e3e93bc48eeb39289a7b
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>

ARM: dts: bcm2711-rpi-4-b: Enable dt nodes for audio, i2c1, spi0

audio, i2c1, spi0 nodes should be enabled as RPI3.

Change-Id: I8ea244b188ac8d1787c1340369f7aa90486f44d6
Reference: 5cf4f3e4 ("ARM: dts: bcm2710-rpi-3-b-plus: Enable dt nodes for audio, i2c1, spi0")
Signed-off-by: Jaechul Lee <jcsing.lee@samsung.com>

rpi4: boot: Fix hdmi group to DMT

There is a problem using the hdmi small monitors causes monitor to
freeze. So defines the HDMI output group DMT, set defualt mode 720p.

Change-Id: I070549ed36423755b7e8742b923f2ac18b8ccc5b
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>

scripts: mkbootimg_rpi4.sh: Fix to install modules on non sudo

On sudo status, env variable is possible not to be preserved and
it causes failure on modules_install. So fix to install modules on
non sudo status and then move the directories and files to image
area.

[From repo of tizen rpi3: 89dcbe9b298c scripts: mkbootimg_rpi3.sh: Fix to install modules on non sudo status]
Change-Id: Ie7047c23762b668a08abf387dd76cf9cc8571937
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>

rpi4: boot: Add to support mipi-csi camera module

Add to support mipi-csi camera module with the options, start_x=1
and disable_camera_led=1, in config.txt.

Change-Id: I450c291599031437a9fe58cac94a0d18c6cf58a9
Reference: https://www.raspberrypi.org/documentation/configuration/config-txt/boot.md
Reference: https://www.raspberrypi.org/documentation/configuration/config-txt/camera.md
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>

scripts: mkbootimg_rpi4.sh: Remove rename for kernel7l.img.

Use origin kernel image name(zImage) because of specified kernel in
the config.txt file.

Change-Id: If4a255fb3b89a892a1e7305b6ae6a33829730ae5
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>

rpi4: boot: add kernel name in config.txt

Add kernel name in config.txt.

Change-Id: Iff5b38da853a54296c2eef7b6d5eaf24761b22cf
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>

packaging: remove unnecessary requirement

Remove unnecessary requirement instead of comment.

Change-Id: I891326a384fffd192d3cac4435116c82c95bc1e3
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>

rpi4: Remove unused files

Remove unused files in rpi4.

Change-Id: I29525779cf28c33e68da9ac22abd895b2711be8c
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>

scripts: Add mkbootimg_rpi4.sh

This script is to make boot.img and modules.img for rpi4.

Change-Id: I1a57e86070b631ba032e9cd35282f192adc6f379
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>

rpi4: Add cmdline.txt file

The cmdline.txt file is need for boot.

Change-Id: I2a6030c2beb5dae0f8607e9e22065aaa7bf5c81d
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>

packaging: Add spec file for rpi4

This adds linux-rpi4.spec file for armv7l rpm packaging.

Change-Id: Ic9aef54edc5f1c718ba2c301e70a4d9ee79af35d
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>

ARM: tizen_bcm2711_defconfig: Fix modules cleanup

Always used modules changed to built-in, also remove unused modules.

Change-Id: I9304cf746e5a7559659f11dd875e7c4eb2d54175
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>

ARM: tizen_bcm2711_defconfig: Fix I2C config to built-in

Fix i2c configuration to built-in.

Change-Id: I91870db7c34635e623b8ae1a1c102c55f746d180
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>

ARM: tizen_bcm2711_defconfig: Fix drm-vc4 to built-in

Fix drm-vc4 configuration to built-in and dependent configuration to
built-in.

Change-Id: I36ee27e9c42a9baccba4b6e022a78acbbe5ba025
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>

tools: Add build script for ARM kernel of rpi4

Add build script for ARM kernel of rpi4.

Change-Id: I96cf3d55235a0a67d610bf87aa9ddf4f5e972411
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>

ARM: tizen_bcm2711_defconfig: Disable bcm2708_fb

This driver is not used at tizen.

Change-Id: Ia524fc59c17ec11578a4366d173879fb40e0ab49
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>

ARM: tizen_bcm2711_defconfig: Enable SMACK

It needs to enable configs related with SMACK for booting tizen
platform.

Change-Id: Ia304c703afc55d13dd2a8a7d14ad8de2c208c22b
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>

ARM: tizen_bcm2711_defconfig: Remove unused module

This module is unused.

Change-Id: Ie3524be3337a590bfe53fa93830067318150ef56
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>

ARM: defconfig: Add tizen_bcm2711_defconfig

tizen_bcm2711_defconfig is from bcm2711_defconfig.

Change-Id: I21d1d2c7e46e8ea4cfb34b5a4465a1c4eb62967b
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>

rpi4: config: Enable serial

Add configration to enable serial in config.txt file.

Change-Id: Ibe5971e1f068a8ef13ec7bb4e16aa9cfe1ab5feb
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>

rpi4: Add config.txt extracted from raspbian full binary

The config.txt file is needed at boot time. And this file from binary
(https://downloads.raspberrypi.org/raspbian_full)

Change-Id: I841b11a4b400e5b44a5ca75f2f14819a35997e5e
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>

rpi4: Add boot files from github

We can get boot binaries that are necessary for booting from master
branch of https://github.com/raspberrypi/firmware.

The git base is the commit "66bafab0055 kernel: Bump to 4.19.65"

Change-Id: Iba608e75426efcc1e45240ca532ec91807b4ce16
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>

Bluetooth: fix wrong indent in __hci_req_update_{scan/adv}_rsp_data()

The commit ac160e08af69 ("Bluetooth: Add Advertising Packet
Configuration") introduces wrong indent which causes build warning for
gcc-7. Fix the wrong indent.

Change-Id: Ia0bde8a8f9660ccf8fa312e3c3ec6c8cb76863f1
Fixes: ac160e08af69 ("Bluetooth: Add Advertising Packet Configuration")
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>

Bluetooth : fix build error

Update device name on remote_name_event, Fix interface define for
build error.

Change-Id: I59df4a7e30f9a83a0efdce516b2a325cb3b0983b
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>

Bluetooth: Fix the potential crash issue

There is a logic error in the event function. We should
check the callback function's parameter before calling.

Change-Id: I06a4a8c50317e5ec4ae8fe35e4b788105e090196
Fixes: bde01c80dd51 ("Bluetooth: Set le data length command and event")
Signed-off-by: DoHyun Pyun <dh79.pyun@samsung.com>

Bluetooth: Set le data length command and event

Sets the data length for the le data packet with in the
advised limits. MGMT command and event are added to handle
the setting of data length.

Change-Id: Ia5c2167743cc9a29190e5631973e9d52d41caa1d
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: Read host suggested default le data length

This patch adds MGMT command and code for supporting reading
default le data length value set at the controller.

Change-Id: I2b81982dc26ed5af4a8f8a3d3913db5d64625260
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: Write host suggested default le data length

This patch adds MGMT command and code for supporting write
default le data length command to the controller.

Change-Id: I3d2c8b622b7913a3ed542342e3ba8076c30dc279
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: Read LE Max data length command

This patch adds the MGMT command and code to support reading
the maximum data length supported command for LE.

Change-Id: I4dc0041f2070de2ccb6a4164c8823612863c941e
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: Fix IPSP connection callback event issue.

This patch fixes the IPSP connection callback event issue
between kernel and bluez layer.

Change-Id: Ia4d625aa8a6dbc9da89a7d9f12308af9c90d0594
Signed-off-by: h.sandeep <h.sandeep@samsung.com>
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: IPSP Connect/Disconnect apis

This patch adds MGMT code to support IPSP connect and
disconnect apis and handle connection state changed event.

Change-Id: I1c41ec4f38cf9a108e443def3bc23c1b964e2985
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: Add support to enable/disable IPSP

This patch supports MGMT commands and code to enable or disable
IPSP 6LowPan features.

Change-Id: Ia866ecfa517c7d7e4320f17d94d80dfeb9261e59
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: Fix issue in the Set LE privacy function.

This patch fixes not to check the hdev power before setting
LE Privacy.

Change-Id: I344ea13b1d90527e3e7554ec616cdc640b85159c
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: Store the key if auth type is P192

This patch allows to store the key after authentication
if auth type is "HCI_LK_AUTH_COMBINATION_P192"

Change-Id: Ie44dbe7dfec361edab61aceaf9b2ca4057b88fa5
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: Cancel the Sniff timer

This patch adds code to cancel the sniff timer.

Change-Id: I756d3b08acf6462044d1fb204064fe12ce1238c1
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: Enable sniff mode for incoming connection

Add provision to set the link poilicy to enable sniff mode
for incoming connection.

Change-Id: Ifff9e9f0838f26a6c96d81f4cbaae43429aa231f
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: Modify fast connectable type.

This patch modifies the fast connectable function
to just set the type.

Change-Id: I0cce96f85d823f9798ae7f147c4e33ce7b18e0e3
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: Send Authentication Request command on pairing failure

This patch allows to send HCI_OP_AUTH_REQUESTED command
to the remote device if pairing failure happens because
of pin or key missing error.

Change-Id: I9c28394dc06b22fd5fe9e58ac0b7d728c086bde4
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: Enable inquiry and page scan

This patch enables the inquiry and page scan after ACL
disconnection with one device and if there are no other
devices connected.

Change-Id: Ifb28be7d23f237d35112b2e0739ed55169baacf7
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: Change authentication requirement.

This patch updates the authentication requirement to general
MITM if local and remote device IO capabilities are not
NO_INPUT_NO_OUTPUT.

Change-Id: Ie3955c3f8287418e74af20d40bdf30d0f1963e31
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: Set link Supervision timeout for a connection

This patch allows to set the supervision timeout for a connection
if the device role is master.

Change-Id: I7897167ec07803f3059f2ab4d3314b0b7a951533
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: Set filter policy for LE connection

This patch sets the filter policy to a default value 0x01 during
LE auto connection if the destination address is not set. And it
updates the destination address once the LE connection complete
event is recieved during LE auto connection. And for it checks
valid destination address before cancelling LE connection when
connection timeout occurs.

Change-Id: I9877556c0b0ab4826f5f4934ead4d85b7837036d
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
[squash patches, LE connection policy, set dest address and check dest address before cancelling connection]
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: Get Advertising TX power

This patch adds MGMT command to read the advertising TX power.

Change-Id: Ide9e5d332f034928d2eae2cbd68a025a0d42be1b
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: Set the link for SCO connection

This patch sets the link policy for SCO/eSCO connection.

Change-Id: I71caef5a3887f73a10329b6886c8cf52b80e8d37
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
[add link policy setting in sco connection]
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: Add MGMT command to set SCO settings

Added code to set sco settings.

Change-Id: I37aa572436241b06e00d1e9e75964aac747eeba5
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
[remove sco link policy part]
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: Add multiple LE advertise state change event

This patch adds code for providing multiple LE advertisement state
changed event to upper layer.

Change-Id: I58fb8044e74402376ec30b121081edce7c8709d1
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
[divide hci_vendor_mutli_adv_state_change_evt and remove hci event structure from mgmt]
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: Add LE device found MGMT event

This patch adds new MGMT event for LE device discovery and allows
the handling of all advertisement packets in platform.

Change-Id: I1927acb75eff0b60a5899898c6d7a000e1a108ef
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: fix vendor ext rssi link alert event

This patch fixes style for rssi link alert event from vendor
specific group ext.

Change-Id: I0e7003e417c5f5a590cce8264caccad515dd3c10
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: Add H/W TX timeout error MGMT event

This patch sends the H/W TX timeout error MGMT event if HCI command
timeout occurs after sending HCI commands.

Change-Id: I5eb593f2fe4d31c404dd94ef582790e47d03b10a
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: Add hardware error MGMT event

Add code to handle hardware error MGMT event.

Change-Id: I5875ea2aeae7aba95c1f8e15b456704dc6bcdee4
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: Add LE vendor specific event handler

This patch adds the vendor specific LE meta event handler.
It handles the vendor specific handles like,
LE_MULTI_ADV_STATE_CHANGE_SUB_EVENT, LE_RSSI_LINK_ALERT.

Change-Id: I1f344a31e36f9c7442fe0bd8b598e67d9f5fb9bf
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
[divide hci vendor speicif group event function]
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: Add set LE scan parameter feature

Added new MGMT command to set LE scan parameters

Change-Id: I5ea660f97e93dfcc72273971ad0250e7f582f718
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: Set Manufacturer data feature

Added new MGMT command to set the manufacturer data
in the BR/EDR packet.

Change-Id: Ie08062f4cad0c676deab94fd95fdc1a8c5602135
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: Add LE connection parameter update procedure

Added new MGMT command to update LE connection parameters

Change-Id: I6ae16513437cd42d40e75958aa8415baa1cbedbb
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: Add stop LE auto connection feature

Added new MGMT command to disable LE auto connection.

Change-Id: I1f5f61b83227501ad54019008b405fd47fd722a3
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: Add BT LE discovery feature

This patch adds new MGMT commands to start LE discovery separately
and handles LE discovery state.

Change-Id: I85958b8c2b5c7e28f57c69e86037ab1e61a75db0
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: Update device name on remote_name_event

This patch updates the device name on receiving the HCI event
remote_name_event during connection establishment.

Change-Id: I9a217e6760b1803a70af201a3f6903e722079749
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: Add RSSI Monitor feature

Added feature support for monitoring the RSSI value.
Commands and events for enabling, disabling and setting
rssi threshold values are added.

Change-Id: I850643a9228afc017e54217a11826b9c6a68a96b
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: Functions to modify WhiteList

This patch provides MGMT commands to manage the white
list which includes, adding, removing and clearing the
devices from white list.

Change-Id: If71107129d3a090ae81448a8122b76accd4f5522
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
Signed-off-by: DoHyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: Add Advertising Packet Configuration

This patch provides new MGMT commands to configure
the advertising data and scan response data packets for
LE peripheral devices.

Change-Id: I914d13795f4fb58e5f2e1cadb55086f4bcbc82df
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
Signed-off-by: DoHyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>
[jhoon20.kim: adjust some codes to apply it in 5.4 kernel]
Signed-off-by: Junghoon Kim <jhoon20.kim@samsung.com>

Bluetooth: Add MGMT tizen_handlers and TIZEN_OP_BASE_CODE.

Added the basic skeleton code for tizen_mgmt_handlers and
mgmt_tizen.h header file.

Change-Id: I8f3100aa79e6673840ba561f0a9c50238ca0880b
Signed-off-by: h.sandeep <h.sandeep@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

Bluetooth: Add "TIZEN_BT" flag

Added the tizen specific flag for use in adding tizen patches.

Change-Id: Ia391644fddbe600c8d845e0bf0808f587aa73e0c
Signed-off-by: Sudha Bheemanna <b.sudha@samsung.com>
Signed-off-by: DoHyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: Amit Purwar <amit.purwar@samsung.com>

misc: tizen-inform-reboot: Use ksys_open() and ksys_close() wrappers

Using ksys_open() and ksys_close() wrappers allow us to avoid the
in-kernel calls to the sys_open() and sys_close() syscalls.

Change-Id: Iea33654daef917f88cede31675c66e8b5becad77
Signed-off-by: Junghoon Kim <jhoon20.kim@samsung.com>

LOCAL / mm, page_alloc: Add print page allocation failure reason

There is an unclear problem when page alloc failed. So clearly print
the cause of the failure.

Change-Id: Ie59e1d4e34deabb8733268edfb433754f43766a8
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>

net: rtl8192cu: change config name as vendor driver

There is already rtl8192cu mainline driver.
To distinguish with vendor driver, changed config name to
RTL8192CU_VENDOR.

Change-Id: I2663bc12f787cc4f417a13c9b4de42b4b63a8efb
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>

staging: bcm2835-camera: fix overflow warnings

Fix overflow in implicit constant conversion warnings.

Change-Id: I3e419cb927241c9400147b36a2e36f2173c96025
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>

misc: tizen-inform-reboot: Add support for download mode

To pass download mode information to bootloader, this patch adds
the new parameter 'download' to reboot command.

Change-Id: I4673a0badf42429987f91edd960b871410bfb794
Signed-off-by: Dongwoo Lee <dwoo08.lee@samsung.com>

misc: tizen-inform-reboot: resolve sync failure about reboot parameter

Currently, writing reboot paramter into INFORM partition fails
infrequently.

Resolve this issue by calling sync_filesystem function so that it writes
out and waits upon all dirty data associated with this superblock.

Change-Id: Ic62df0c3c4e565ca7211eb85661ead6979f0ad8d
Signed-off-by: Junghoon Kim <jhoon20.kim@samsung.com>

misc: make sure Tizen notifier is executed before reset

In case of RaspberryPi the CPU is reset by watchdog triggered from
the bcm2835_restart_notifier_call function. Tizen notifier needs higher
priority to be called before the watchdog.

Change-Id: Ia7f6d895f6f40d1a9b4e57ad41b5bdb55c94f4f2
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>

misc: add Tizen reboot notifier for passing reboot parameter

To determine booting mode (e.g, fota or recovery) in u-boot side, reboot
parameter should be passed through inform partition.

Add Tizen reboot notifier for passing reboot parameter.

Change-Id: I5830dcf58ec6905b0bc382599aa9ff1251f817d8
Signed-off-by: Junghoon Kim <jhoon20.kim@samsung.com>

drm/vc4: Calculate bpc based on max_requested_bpc

This aligns vc4 with Intel, AMD and Synopsis drivers and fixes max bpc
connector property not working as expected on monitors with YCbCr 4:2:2
support but not deep color support.

max_bpc in connector state is clamped at max_bpc from display info and
the latter only takes deep color modes into account so it will always
be 8, even if the display can do 4:2:2 12-bit output.

Signed-off-by: Matthias Reichl <hias@horus.com>

Merge remote-tracking branch 'stable/linux-5.15.y' into rpi-5.15.y

Linux 5.15.92

Link: https://lore.kernel.org/r/20230203101007.985835823@linuxfoundation.org
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Shuah Khan <skhan@linuxfoundation.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Bagas Sanjaya <bagasdotme@gmail.com>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: Ron Economos <re@w6rz.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: mctp: purge receive queues on sk destruction

commit 60bd1d9008a50cc78c4033a16a6f5d78210d481c upstream.

We may have pending skbs in the receive queue when the sk is being
destroyed; add a destructor to purge the queue.

MCTP doesn't use the error queue, so only the receive_queue is purged.

Fixes: 833ef3b91de6 ("mctp: Populate socket implementation")
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/20230126064551.464468-1-jk@codeconstruct.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: fix NULL pointer in skb_segment_list

commit 876e8ca8366735a604bac86ff7e2732fc9d85d2d upstream.

Commit 3a1296a38d0c ("net: Support GRO/GSO fraglist chaining.")
introduced UDP listifyed GRO. The segmentation relies on frag_list being
untouched when passing through the network stack. This assumption can be
broken sometimes, where frag_list itself gets pulled into linear area,
leaving frag_list being NULL. When this happens it can trigger
following NULL pointer dereference, and panic the kernel. Reverse the
test condition should fix it.

[19185.577801][    C1] BUG: kernel NULL pointer dereference, address:
...
[19185.663775][    C1] RIP: 0010:skb_segment_list+0x1cc/0x390
...
[19185.834644][    C1] Call Trace:
[19185.841730][    C1]  <TASK>
[19185.848563][    C1]  __udp_gso_segment+0x33e/0x510
[19185.857370][    C1]  inet_gso_segment+0x15b/0x3e0
[19185.866059][    C1]  skb_mac_gso_segment+0x97/0x110
[19185.874939][    C1]  __skb_gso_segment+0xb2/0x160
[19185.883646][    C1]  udp_queue_rcv_skb+0xc3/0x1d0
[19185.892319][    C1]  udp_unicast_rcv_skb+0x75/0x90
[19185.900979][    C1]  ip_protocol_deliver_rcu+0xd2/0x200
[19185.910003][    C1]  ip_local_deliver_finish+0x44/0x60
[19185.918757][    C1]  __netif_receive_skb_one_core+0x8b/0xa0
[19185.927834][    C1]  process_backlog+0x88/0x130
[19185.935840][    C1]  __napi_poll+0x27/0x150
[19185.943447][    C1]  net_rx_action+0x27e/0x5f0
[19185.951331][    C1]  ? mlx5_cq_tasklet_cb+0x70/0x160 [mlx5_core]
[19185.960848][    C1]  __do_softirq+0xbc/0x25d
[19185.968607][    C1]  irq_exit_rcu+0x83/0xb0
[19185.976247][    C1]  common_interrupt+0x43/0xa0
[19185.984235][    C1]  asm_common_interrupt+0x22/0x40
...
[19186.094106][    C1]  </TASK>

Fixes: 3a1296a38d0c ("net: Support GRO/GSO fraglist chaining.")
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Yan Zhai <yan@cloudflare.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/r/Y9gt5EUizK1UImEP@debian
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

selftests: Provide local define of __cpuid_count()

commit a23039c7306f53416ba35d230201398ea34f4640 upstream.

Some selftests depend on information provided by the CPUID instruction.
To support this dependency the selftests implement private wrappers for
CPUID.

Duplication of the CPUID wrappers should be avoided.

Both gcc and clang/LLVM provide __cpuid_count() macros but neither
the macro nor its header file are available in all the compiler
versions that need to be supported by the selftests. __cpuid_count()
as provided by gcc is available starting with gcc v4.4, so it is
not available if the latest tests need to be run in all the
environments required to support kernels v4.9 and v4.14 that
have the minimal required gcc v3.2.

Duplicate gcc's __cpuid_count() macro to provide a centrally defined
macro for __cpuid_count() to help eliminate the duplicate CPUID wrappers
while continuing to compile in older environments.

Suggested-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Cc: Kyle Huey <me@kylehuey.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

selftests/vm: remove ARRAY_SIZE define from individual tests

commit e89908201e2509354c40158b517945bf3d645812 upstream.

ARRAY_SIZE is defined in several selftests. Remove definitions from
individual test files and include header file for the define instead.
ARRAY_SIZE define is added in a separate patch to prepare for this
change.

Remove ARRAY_SIZE from vm tests and pickup the one defined in
kselftest.h.

Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Cc: Kyle Huey <me@kylehuey.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tools: fix ARRAY_SIZE defines in tools and selftests hdrs

commit 066b34aa5461f6072dbbecb690f4fe446b736ebf upstream.

tools/include/linux/kernel.h and kselftest_harness.h are missing
ifndef guard around ARRAY_SIZE define. Fix them to avoid duplicate
define errors during compile when another file defines it. This
problem was found when compiling selftests that include a header
with ARRAY_SIZE define.

ARRAY_SIZE is defined in several selftests. There are about 25+
duplicate defines in various selftests source and header files.
Add ARRAY_SIZE to kselftest.h in preparation for removing duplicate
ARRAY_SIZE defines from individual test files.

Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Cc: Kyle Huey <me@kylehuey.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Bluetooth: fix null ptr deref on hci_sync_conn_complete_evt

commit 3afee2118132e93e5f6fa636dfde86201a860ab3 upstream.

This event is just specified for SCO and eSCO link types.
On the reception of a HCI_Synchronous_Connection_Complete for a BDADDR
of an existing LE connection, LE link type and a status that triggers the
second case of the packet processing a NULL pointer dereference happens,
as conn->link is NULL.

Signed-off-by: Soenke Huster <soenke.huster@eknoes.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Ovidiu Panait <ovidiu.panait@eng.windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ACPI: processor idle: Practically limit "Dummy wait" workaround to old Intel systems

commit e400ad8b7e6a1b9102123c6240289a811501f7d9 upstream.

Old, circa 2002 chipsets have a bug: they don't go idle when they are
supposed to.  So, a workaround was added to slow the CPU down and
ensure that the CPU waits a bit for the chipset to actually go idle.
This workaround is ancient and has been in place in some form since
the original kernel ACPI implementation.

But, this workaround is very painful on modern systems.  The "inl()"
can take thousands of cycles (see Link: for some more detailed
numbers and some fun kernel archaeology).

First and foremost, modern systems should not be using this code.
Typical Intel systems have not used it in over a decade because it is
horribly inferior to MWAIT-based idle.

Despite this, people do seem to be tripping over this workaround on
AMD system today.

Limit the "dummy wait" workaround to Intel systems.  Keep Modern AMD
systems from tripping over the workaround.  Remotely modern Intel
systems use intel_idle instead of this code and will, in practice,
remain unaffected by the dummy wait.

Reported-by: K Prateek Nayak <kprateek.nayak@amd.com>
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Tested-by: K Prateek Nayak <kprateek.nayak@amd.com>
Link: https://lore.kernel.org/all/20220921063638.2489-1-kprateek.nayak@amd.com/
Link: https://lkml.kernel.org/r/20220922184745.3252932-1-dave.hansen@intel.com
Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

extcon: usbc-tusb320: fix kernel-doc warning

commit 08099ecd9216219f51cc82637f06797cf81890b6 upstream.

Fix the warning:
drivers/extcon/extcon-usbc-tusb320.c:19: warning: expecting prototype
for drivers/extcon/extcon-tusb320.c(). Prototype was for TUSB320_REG8()
instead

Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Rong Chen <rong.a.chen@intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: fix bad checksum after online resize

commit a408f33e895e455f16cf964cb5cd4979b658db7b upstream.

When online resizing is performed twice consecutively, the error message
"Superblock checksum does not match superblock" is displayed for the
second time. Here's the reproducer:

mkfs.ext4 -F /dev/sdb 100M
mount /dev/sdb /tmp/test
resize2fs /dev/sdb 5G
resize2fs /dev/sdb 6G

To solve this issue, we moved the update of the checksum after the
es->s_overhead_clusters is updated.

Fixes: 026d0d27c488 ("ext4: reduce computation of overhead during resize")
Fixes: de394a86658f ("ext4: update s_overhead_clusters in the superblock during an on-line resize")
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: stable@kernel.org
Link: https://lore.kernel.org/r/20221117040341.1380702-2-libaokun1@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Oleksandr Tymoshenko <ovt@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

cifs: fix return of uninitialized rc in dfs_cache_update_tgthint()

[ Upstream commit d6a49e8c4ca4d399ed65ac219585187fc8c2e2b1 ]

Fix this by initializing rc to 0 as cache_refresh_path() would not set
it in case of success.

Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/all/202301190004.bEHvbKG6-lkp@intel.com/
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

dmaengine: imx-sdma: Fix a possible memory leak in sdma_transfer_init

[ Upstream commit 1417f59ac0b02130ee56c0c50794b9b257be3d17 ]

If the function sdma_load_context() fails, the sdma_desc will be
freed, but the allocated desc->bd is forgot to be freed.

We already met the sdma_load_context() failure case and the log as
below:
[ 450.699064] imx-sdma 30bd0000.dma-controller: Timeout waiting for CH0 ready
...

In this case, the desc->bd will not be freed without this change.

Signed-off-by: Hui Wang <hui.wang@canonical.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20221130090800.102035-1-hui.wang@canonical.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

HID: playstation: sanity check DualSense calibration data.

[ Upstream commit ccf1e1626d37745d0a697db67407beec9ae9d4b8 ]

Make sure calibration values are defined to prevent potential kernel
crashes. This fixes a hypothetical issue for virtual or clone devices
inspired by a similar fix for DS4.

Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

blk-cgroup: fix missing pd_online_fn() while activating policy

[ Upstream commit e3ff8887e7db757360f97634e0d6f4b8e27a8c46 ]

If the policy defines pd_online_fn(), it should be called after
pd_init_fn(), like blkg_create().

Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20230103112833.2013432-1-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

erofs/zmap.c: Fix incorrect offset calculation

[ Upstream commit 6acd87d50998ef0afafc441613aeaf5a8f5c9eff ]

Effective offset to add to length was being incorrectly calculated,
which resulted in iomap->length being set to 0, triggering a WARN_ON
in iomap_iter_done().

Fix that, and describe it in comments.

This was reported as a crash by syzbot under an issue about a warning
encountered in iomap_iter_done(), but unrelated to erofs.

C reproducer: https://syzkaller.appspot.com/text?tag=ReproC&x=1037a6b2880000
Kernel config: https://syzkaller.appspot.com/text?tag=KernelConfig&x=e2021a61197ebe02
link: https://syzkaller.appspot.com/bug?extid=a8e049cd3abd342936b6
Reported-by: syzbot+a8e049cd3abd342936b6@syzkaller.appspotmail.com
Suggested-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Siddh Raman Pant <code@siddh.me>
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Link: https://lore.kernel.org/r/20221209102151.311049-1-code@siddh.me
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bpf: Skip task with pid=1 in send_signal_common()

[ Upstream commit a3d81bc1eaef48e34dd0b9b48eefed9e02a06451 ]

The following kernel panic can be triggered when a task with pid=1 attaches
a prog that attempts to send killing signal to itself, also see [1] for more
details:

  Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
  CPU: 3 PID: 1 Comm: systemd Not tainted 6.1.0-09652-g59fe41b5255f #148
  Call Trace:
  <TASK>
  __dump_stack lib/dump_stack.c:88 [inline]
  dump_stack_lvl+0x100/0x178 lib/dump_stack.c:106
  panic+0x2c4/0x60f kernel/panic.c:275
  do_exit.cold+0x63/0xe4 kernel/exit.c:789
  do_group_exit+0xd4/0x2a0 kernel/exit.c:950
  get_signal+0x2460/0x2600 kernel/signal.c:2858
  arch_do_signal_or_restart+0x78/0x5d0 arch/x86/kernel/signal.c:306
  exit_to_user_mode_loop kernel/entry/common.c:168 [inline]
  exit_to_user_mode_prepare+0x15f/0x250 kernel/entry/common.c:203
  __syscall_exit_to_user_mode_work kernel/entry/common.c:285 [inline]
  syscall_exit_to_user_mode+0x1d/0x50 kernel/entry/common.c:296
  do_syscall_64+0x44/0xb0 arch/x86/entry/common.c:86
  entry_SYSCALL_64_after_hwframe+0x63/0xcd

So skip task with pid=1 in bpf_send_signal_common() to avoid the panic.

  [1] https://lore.kernel.org/bpf/20221222043507.33037-1-sunhao.th@gmail.com

Signed-off-by: Hao Sun <sunhao.th@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/bpf/20230106084838.12690-1-sunhao.th@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

firmware: arm_scmi: Clear stale xfer->hdr.status

[ Upstream commit f6ca5059dc0d6608dc46070f48e396d611f240d6 ]

Stale error status reported from a previous message transaction must be
cleared before starting a new transaction to avoid being confusingly
reported in the following SCMI message dump traces.

Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20221222183823.518856-2-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: imx8mq-thor96: fix no-mmc property for SDHCI

[ Upstream commit ef10d57936ead5e817ef7cea6a87531085e77773 ]

There is no "no-emmc" property, so intention for SD/SDIO only nodes was
to use "no-mmc".

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: freescale: Fix pca954x i2c-mux node names

[ Upstream commit b025b4f5c288e29bbea421613a5b4eacf9261fbb ]

"make dtbs_check":

    arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dtb: pca9547@77: $nodename:0: 'pca9547@77' does not match '^(i2c-?)?mux'
    From schema: Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
    arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dtb: pca9547@77: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'i2c@4' were unexpected)
    From schema: Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
    ...

Fix this by renaming PCA954x nodes to "i2c-mux", to match the I2C bus
multiplexer/switch DT bindings and the Generic Names Recommendation in
the Devicetree Specification.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: vf610: Fix pca9548 i2c-mux node names

[ Upstream commit 42825d1f269355d63554ab3c3762611e4d8053e9 ]

"make dtbs_check":

    arch/arm/boot/dts/vf610-zii-dev-rev-b.dtb: tca9548@70: $nodename:0: 'tca9548@70' does not match '^(i2c-?)?mux'
    From schema: Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
    arch/arm/boot/dts/vf610-zii-dev-rev-b.dtb: tca9548@70: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'i2c@0', 'i2c@1', 'i2c@2', 'i2c@3', 'i2c@4' were unexpected)
    From schema: /scratch/geert/linux/linux-renesas/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
    ...

Fix this by renaming PCA9548 nodes to "i2c-mux", to match the I2C bus
multiplexer/switch DT bindings and the Generic Names Recommendation in
the Devicetree Specification.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: imx: Fix pca9547 i2c-mux node name

[ Upstream commit f78985f9f58380eec37f82c8a2c765aa7670fc29 ]

"make dtbs_check":

    arch/arm/boot/dts/imx53-ppd.dtb: i2c-switch@70: $nodename:0: 'i2c-switch@70' does not match '^(i2c-?)?mux'
    From schema: Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
    arch/arm/boot/dts/imx53-ppd.dtb: i2c-switch@70: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'i2c@0', 'i2c@1', 'i2c@2', 'i2c@3', 'i2c@4', 'i2c@5', 'i2c@6', 'i2c@7' were unexpected)
    From schema: Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml

Fix this by renaming the PCA9547 node to "i2c-mux", to match the I2C bus
multiplexer/switch DT bindings and the Generic Names Recommendation in
the Devicetree Specification.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Merge remote-tracking branch 'stable/linux-5.15.y' into rpi-5.15.y

drm/vc4_plane: Add support for YUV444 formats

Support displaying DRM_FORMAT_YUV444 and DRM_FORMAT_YVU444 formats.
Tested with kmstest and kodi. e.g.

kmstest -r 1920x1080@60 -f 400x300-YU24

Note: without the shift of width, only half the chroma is fetched,
resulting in correct left half of image and corrupt colours on right half.

The increase in width shouldn't affect fetching of Y data,
as the hardware will clamp at dest width.

Signed-off-by: Dom Cobley <popcornmix@gmail.com>

Linux 5.15.91

Link: https://lore.kernel.org/r/20230130134316.327556078@linuxfoundation.org
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Shuah Khan <skhan@linuxfoundation.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Bagas Sanjaya <bagasdotme@gmail.com>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Allen Pais <apais@linux.microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>