media: Documentation: v4l: Document required controls on camera sensors

Raw camera sensors connected to parallel or CSI-2 busses need to implement
V4L2_CID_LINK_FREQ control so receiver drivers can configure the hardware
accordingly.

Document this. Also say V4L2_CID_PIXEL_RATE is recommended for such
hardware.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: Documentation: v4l: Fix language

Remove extra "is" from sentence explaining V4L2_CID_PIXEL_RATE may be used
to tell the pixel rate used by a transmitter driver. Also call
V4L2_CID_PIXEL_RATE a control.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: ipu3-cio2: Check receved the size against payload size, not buffer size

Compare the received size of the payload size, not the allocated size of
the buffer that is page aligned. This way also images that aren't aligned
to page size are not warned about.

Also wrap a line over 80 characters.

Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Jean-Michel Hautbois <jeanmichel.hautbois@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: ov7670: do not aggregate returns

Adding muliple status together loses individual failures.
Check each status separately.

Clean up some other returns for consistency.

Fixed several coding style problems by running
the file through checkpatch.pl --fix-inplace

Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: stm32-dcmi: add 8-bit Bayer formats support

Add BA81, GBRG, GRBG, RGGB formats in the list of
supported capture formats.

Signed-off-by: Alain Volmat <alain.volmat@st.com>
Acked-by: Hugues FRUCHET <hugues.fruchet@st.com>
Reviewed-by: Philippe CORNU <philippe.cornu@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: stm32-dcmi: remove deprecated dmaengine_terminate_all()

Replace dmaengine_terminate_all() by dmaengine_terminate_sync()
to ensure that all pending dma operations are really finished.
This is not ensured by dmaengine_terminate_all() and this API
is deprecated, so better to use the _sync() variant.

Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Reviewed-by: Philippe CORNU <philippe.cornu@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: stm32-dcmi: don't print an error on probe deferral

Change stm32-dcmi driver to not print an error message when the
device probe operation is deferred.

Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Acked-by: Hugues Fruchet <hugues.fruchet@st.com>
Tested-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: ov5640: add support of 160x120 resolution

Add support of 160x120 resolution.

Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: ipu3-cio2: Remove traces of returned buffers

If starting a video buffer queue fails, the buffers are returned to
videobuf2. Remove the reference to the buffer from the driver's queue as
well.

Fixes: c2a6a07afe4a ("media: intel-ipu3: cio2: add new MIPI-CSI2 driver")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: stable@vger.kernel.org # v4.16 and up
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: ipu3-cio2: Rename CIO2_IMAGE_MAX_LENGTH as CIO2_IMAGE_MAX_HEIGHT

CIO2_IMAGE_MAX_LENGTH is the maximum height of the image. Rename it as
"CIO2_IMAGE_MAX_HEIGHT" in order to better describe what it is.

Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: ipu3-cio2: Remove explicit type from frame size checks

Now that the values are unsigned, we can remove the explicit cast to u32.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: ipu3-cio2: Use unsigned values where appropriate

Use unsigned values for width, height, bit shifts and registers,
effectively for all definitions that are not signed.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: ipu3-cio2: Make the field on subdev format V4L2_FIELD_NONE

The ipu3-cio2 doesn't make use of the field and this is reflected in V4L2
buffers as well as the try format. Do this in active format, too.

Fixes: c2a6a07afe4a ("media: intel-ipu3: cio2: add new MIPI-CSI2 driver")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@vger.kernel.org # v4.16 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: ipu3-cio2: Validate mbus format in setting subdev format

Validate media bus code, width and height when setting the subdev format.

This effectively reworks how setting subdev format is implemented in the
driver.

Fixes: c2a6a07afe4a ("media: intel-ipu3: cio2: add new MIPI-CSI2 driver")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@vger.kernel.org # v4.16 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: ipu3-cio2: Serialise access to pad format

Pad format can be accessed from user space. Serialise access to it.

Fixes: c2a6a07afe4a ("media: intel-ipu3: cio2: add new MIPI-CSI2 driver")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: stable@vger.kernel.org # v4.16 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: ipu3-cio2: Return actual subdev format

Return actual subdev format on ipu3-cio2 subdev pads. The earlier
implementation was based on an infinite recursion that exhausted the
stack.

Reported-by: Tsuchiya Yuto <kitakar@gmail.com>
Fixes: c2a6a07afe4a ("media: intel-ipu3: cio2: add new MIPI-CSI2 driver")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: stable@vger.kernel.org # v4.16 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: v4l: subdev: Improve link format validation debug messages

The existing link format validation failure debug message in media-entity.c
helped to pinpoint the point of failure but provided no additional
information what's wrong. Tell the user exactly why the validation failed.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: i2c: ov772x: Add test pattern control

Add support for test pattern control supported by the sensor.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: i2c: ov772x: Add support for BT.656 mode

Add support to read the bus-type for V4L2_MBUS_BT656 and enable BT.656
mode in the sensor if needed.

For backward compatibility with older DTS where the bus-type property was
not mandatory, assume V4L2_MBUS_PARALLEL as it was the only supported bus
at the time. v4l2_fwnode_endpoint_alloc_parse() will not fail if
'bus-type' is not specified.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: i2c: ov772x: Parse endpoint properties

Parse endpoint properties using v4l2_fwnode_endpoint_alloc_parse()
to determine the bus type and store it in the driver structure.

Set bus_type to V4L2_MBUS_PARALLEL as it's the only supported one

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: rcar-csi2: Set bus type when parsing fwnode

The only supported bus for the R-Car CSI-2 driver is CSI-2 DPHY, specify
this before parsing the fwnode.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: rcar-csi2: Switch to using fwnode instead of OF

Use the fwnode_graph_get_endpoint_by_id() interface instead of
of_graph_get_endpoint_by_regs() to fetch the fwnode. This saves
translating between a device_node and fwnode_handle.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: MAINTAINERS: Add ADV7604 bindings documentation

Add the YAML dt-bindings document for ADV7604.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: dt-bindings: adv7604: Convert bindings to json-schema

Convert ADV7604 video decoder documentation to json-schema.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: dt-bindings: adv7604: Fix documentation for hpd-gpios

As of [1] the hpd-gpios property is optional, document it as such.

1. commit 269bd1324fbfaa52 ("[media] media: adv7604: improve usage of gpiod API")

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: v4l2-fwnode: Say it's fine to use v4l2_fwnode_endpoint_parse

Earlier it was expected that there would be more variable size endpoint
properties and that most if not all drivers would need them. For that
reason it was expected also that v4l2_fwnode_endpoint_parse would no
longer be needed.

What actually happened that not all drivers require "link-frequencies",
the only variable size media endpoint property without a small upper
limit. Therefore drivers that do not need that information are fine using
v4l2_fwnode_endpoint_parse. So don't tell drivers to use
v4l2_fwnode_endpoint_alloc_parse in all cases.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: v4l2-fwnode: Rework v4l2_fwnode_endpoint_parse documentation

Rework the documentation of v4l2_fwnode_endpoint_parse for better
readability, usefulness and correctness.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: v4l2-fwnode: Don't zero parts of struct v4l2_fwnode_endpoint anymore

Don't zero parts of the vep argument to v4l2_fwnode_endpoint_parse()
anymore as this can no longer be done while still supporting defaults on
multiple bus types.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: v4l2-fwnode: v4l2_fwnode_endpoint_parse caller must init vep argument

Document that the caller of v4l2_fwnode_endpoint_parse() must init the
fields of struct v4l2_fwnode_endpoint (vep argument) fields.

It used to be that the fields were zeroed by v4l2_fwnode_endpoint_parse
when bus type was set to V4L2_MBUS_UNKNOWN but with recent changes (Fixes:
line below) that no longer makes sense.

Fixes: bb4bba9232fc ("media: v4l2-fwnode: Make bus configuration a struct")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: adv748x: Zero entire struct v4l2_fwnode_endpoint

The v4l2_fwnode_parse_endpoint() function can make use of defaults in
multiple bus types. To use this feature, all callers must zero the rest of
the fields of this struct, too. All other drivers appear to do that
already apart from this one.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: dt-bindings: convert CODA VPU bindings to yaml

Convert to YAML and add generic IP core compatibles "cnm,codadx6",
"cnm,codahx4", "cnm,coda7541", and "cnm,coda960" in addition to the SoC
specific compatibles. The new generic compatibles are already used in
the SoC device trees and replace the free form comments. For example:

- compatible : should be "fsl,<chip>-src" for i.MX SoCs:
  (a) "fsl,imx27-vpu" for CodaDx6 present in i.MX27

turns into:

properties:
  compatible:
    oneOf:
      - items:
          - const: fsl,imx27-vpu
          - const: cnm,codadx6

This allows to properly specify the secondary JPEG unit interrupt that
is only present on cnm,coda960.

Also add the missing "fsl,imx6dl-vpu", "cnm,coda960" compatible.
The AXI bus connection to the internal SRAM is different between i.MX6Q
and i.MX6DL, which requires the driver to load a different firmware
depending on the SoC.

Further, specify the power-domain property for i.MX6 and change the
clock order from "ahb", "per" to "per", "ahb". This order is currently
used in all SoC device trees.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: dt-bindings: media: ov772x: Document endpoint props

Document endpoint properties for the parallel bus type and
add them to the example.

Specify a few constraints:
- If the bus type is BT.656 no hsync or vsync polarities can be
  specified.
- If the bus width is 10 bits, not data-shift can be applied.

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: dt-bindings: media: ov772x: Make bus-type mandatory

In order to establish required properties based on the selected
bus type, make the 'bus-type' property mandatory. As this change
documents an endpoint property, also document the 'remote-endpoint'
one now that the 'endpoint' schema has been expanded.

Binary compatibility with existing DTB is kept as the driver does not
enforce the property to be present, and shall fall-back to default
parallel bus configuration, which was the only supported bus type, if
the property is not specified.

Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: dt-bindings: media: ov772x: Convert to json-schema

Convert the ov772x binding document to json-schema and update
the MAINTAINERS file accordingly.

Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: dt-bindings: media: imx214: Convert to json-schema

Convert the imx214 bindings document to json-schema and update
the MAINTAINERS file accordingly.

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: dt-bindings: media: mt9v111: Convert to json-schema

Convert the mt9v111 bindings document to json-schema and update
the MAINTAINERS file accordingly.

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: imx274: add support for sensor mode6, 1280x540

Add support for the mode 6 for the sensor, this mode uses
3/8 subsampling and 3 horizontal binning.
Aspect ratio is changed.
Split the bin_ratio variable into two parts, one for
width and one for height, as the ratio is no longer preserved
when doing subsampling in this mode.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: imx274: remove binning enum

Binning enum is unused. Remove from driver.

Suggested-by: Sakari Ailus <sakari.ailus@ifi.fi>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: i2c: imx274: Add IMX274 power on and off sequence

IMX274 has analog 2.8V supply, digital core 1.8V supply, and vddl digital
io 1.2V supply which are optional based on camera module design.

IMX274 also need external 24Mhz clock and is optional based on
camera module design.

This patch adds support for IMX274 power on and off to enable and
disable these supplies and external clock.

Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: i2c: imx274: Remove stop stream i2c writes during remove

Sensor should already be in standby during remove and there is no
need to configure sensor registers for stream stop.

Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: i2c: imx274: Fix Y_OUT_SIZE register setting

As per Sony IMX274 Y_OUT_SIZE should be the height of effective
image output from the sensor which are the actual total lines
sent over MIPI CSI to receiver.

So, Y_OUT_SIZE should be same as crop height and this patch fixes it.

Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: v4l2-async: Fix trivial documentation typo

Fix the incorrect spelling asyncrhronous as asynchronous, which is
visible in the public documentation of enum v4l2_async_match_type.

Fixes: ab4f5a4afc2d ("[media] v4l2-async: document the remaining stuff")
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: ov2740: select regmap

Fix OV2740 build breakage by selecting REGMAP_I2C config:

ov2740.c:1011:23: error: variable has incomplete type 'struct regmap_config'
        struct regmap_config regmap_config = { };
                             ^
ov2740.c:1011:9: note: forward declaration of 'struct regmap_config'
        struct regmap_config regmap_config = { };
               ^
ov2740.c:1028:11: error: implicit declaration of function 'devm_regmap_init_i2c'
        regmap = devm_regmap_init_i2c(client, &regmap_config);

Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: ov2740: change the minimal exposure value to 4

The minimal valid exposure value should be 4 lines instead of 8 for
ov2740 mannual exposure control.

Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: i2c: tvp5150: simplify getting state container

The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:

    struct i2c_client *client = to_i2c_client(struct device *dev)
    struct v4l2_subdev *sd = i2c_get_clientdata(client);

This allows to remove local variable 'client' and few pointer
dereferences.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: i2c: smiapp: simplify getting state container

The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:

    struct i2c_client *client = to_i2c_client(struct device *dev)
    struct v4l2_subdev *sd = i2c_get_clientdata(client);

This allows to remove local variable 'client' and few pointer
dereferences.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: i2c: ov8856: simplify getting state container

The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:

    struct i2c_client *client = to_i2c_client(struct device *dev)
    struct v4l2_subdev *sd = i2c_get_clientdata(client);

This allows to remove local variable 'client' and few pointer
dereferences.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: i2c: ov7740: simplify getting state container

The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:

    struct i2c_client *client = to_i2c_client(struct device *dev)
    struct v4l2_subdev *sd = i2c_get_clientdata(client);

This allows to remove local variable 'client' and few pointer
dereferences.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: i2c: ov5695: simplify getting state container

The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:

    struct i2c_client *client = to_i2c_client(struct device *dev)
    struct v4l2_subdev *sd = i2c_get_clientdata(client);

This allows to remove local variable 'client' and few pointer
dereferences.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: i2c: ov5675: simplify getting state container

The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:

    struct i2c_client *client = to_i2c_client(struct device *dev)
    struct v4l2_subdev *sd = i2c_get_clientdata(client);

This allows to remove local variable 'client' and few pointer
dereferences.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: i2c: ov5670: simplify getting state container

The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:

    struct i2c_client *client = to_i2c_client(struct device *dev)
    struct v4l2_subdev *sd = i2c_get_clientdata(client);

This allows to remove local variable 'client' and few pointer
dereferences.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: i2c: ov2740: simplify getting state container

The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:

    struct i2c_client *client = to_i2c_client(struct device *dev)
    struct v4l2_subdev *sd = i2c_get_clientdata(client);

This allows to remove local variable 'client' and few pointer
dereferences.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: i2c: ov2685: simplify getting state container

The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:

    struct i2c_client *client = to_i2c_client(struct device *dev)
    struct v4l2_subdev *sd = i2c_get_clientdata(client);

This allows to remove local variable 'client' and few pointer
dereferences.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: i2c: ov2680: simplify getting state container

The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:

    struct i2c_client *client = to_i2c_client(struct device *dev)
    struct v4l2_subdev *sd = i2c_get_clientdata(client);

This allows to remove local variable 'client' and few pointer
dereferences.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: i2c: ov13858: simplify getting state container

The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:

    struct i2c_client *client = to_i2c_client(struct device *dev)
    struct v4l2_subdev *sd = i2c_get_clientdata(client);

This allows to remove local variable 'client' and few pointer
dereferences.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: i2c: hi556: simplify getting state container

The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:

    struct i2c_client *client = to_i2c_client(struct device *dev)
    struct v4l2_subdev *sd = i2c_get_clientdata(client);

This allows to remove local variable 'client' and few pointer
dereferences.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: i2c: et8ek8: simplify getting state container

The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:

    struct i2c_client *client = to_i2c_client(struct device *dev)
    struct v4l2_subdev *sd = i2c_get_clientdata(client);

This allows to remove local variable 'client' and few pointer
dereferences.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: i2c: dw9768: simplify getting state container

The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:

    struct i2c_client *client = to_i2c_client(struct device *dev)
    struct v4l2_subdev *sd = i2c_get_clientdata(client);

This allows to remove local variable 'client' and few pointer
dereferences.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: i2c: ak7375: simplify getting state container

The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:

    struct i2c_client *client = to_i2c_client(struct device *dev)
    struct v4l2_subdev *sd = i2c_get_clientdata(client);

This allows to remove local variable 'client' and few pointer
dereferences.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: i2c: adv7180: simplify getting state container

The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:

    struct i2c_client *client = to_i2c_client(struct device *dev)
    struct v4l2_subdev *sd = i2c_get_clientdata(client);

This allows to remove local variable 'client' and few pointer
dereferences.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: i2c: adp1653: simplify getting state container

The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:

    struct i2c_client *client = to_i2c_client(struct device *dev)
    struct v4l2_subdev *sd = i2c_get_clientdata(client);

This allows to remove local variable 'client' and few pointer
dereferences.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: i2c: ad5820: simplify getting state container

The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:

    struct i2c_client *client = to_i2c_client(struct device *dev)
    struct v4l2_subdev *sd = i2c_get_clientdata(client);

This allows to remove local variable 'client' and few pointer
dereferences.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: i2c: imx355: silence unused acpi_device_id warning

If driver is built without ACPI, the struct acpi_device_id won't be
used:

  drivers/media/i2c/imx355.c:1836:36: warning:
    'imx355_acpi_ids' defined but not used [-Wunused-const-variable=]

[Sakari Ailus: Added a space before __maybe_unused]

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: i2c: imx355: simplify getting state container

The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:

    struct i2c_client *client = to_i2c_client(struct device *dev)
    struct v4l2_subdev *sd = i2c_get_clientdata(client);

This allows to remove local variable 'client' and few pointer
dereferences.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: i2c: imx319: silence unused acpi_device_id warning

If driver is built without ACPI, the struct acpi_device_id won't be
used:

  drivers/media/i2c/imx319.c:2536:36: warning:
    'imx319_acpi_ids' defined but not used [-Wunused-const-variable=]

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: i2c: imx319: simplify getting state container

The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:

    struct i2c_client *client = to_i2c_client(struct device *dev)
    struct v4l2_subdev *sd = i2c_get_clientdata(client);

This allows to remove local variable 'client' and few pointer
dereferences.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: i2c: imx290: simplify getting state container

The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:

    struct i2c_client *client = to_i2c_client(struct device *dev)
    struct v4l2_subdev *sd = i2c_get_clientdata(client);

This allows to remove local variable 'client' and few pointer
dereferences.  White at it, use 'dev' directly instead of 'imx290->dev'.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: i2c: imx219: simplify getting state container

The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:

    struct i2c_client *client = to_i2c_client(struct device *dev)
    struct v4l2_subdev *sd = i2c_get_clientdata(client);

This allows to remove local variable 'client' and few pointer
dereferences.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: v4l2-fwnode: Return -EINVAL for invalid bus-type

Return -EINVAL if invalid bus-type is detected while parsing endpoints.

Fixes: 26c1126c9b56 ("media: v4l: fwnode: Use media bus type for bus parser selection")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: staging: rkisp1: rsz: make const array static, makes object smaller

Don't populate the const array dev_names on the stack but instead it
static. Makes the object code smaller by 15 bytes.

Before:
   text    data     bss     dec     hex filename
  17091    2648      64   19803    4d5b media/rkisp1/rkisp1-resizer.o

After:
   text    data     bss     dec     hex filename
  17012    2712      64   19788    4d4c media/rkisp1/rkisp1-resizer.o

(gcc version 10.2.0)

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: MAINTAINERS: camss: Add Robert Foss as co-maintainer

I would like to contribute some of my time to co-maintain the CAMSS
driver. I'm currently working to extend CAMSS to new hardware platforms.

Signed-off-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: remove unneeded break

A break is not needed if it is preceded by a return

Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: staging: media: imx: remove unnecessary variable use

Use of variable vc_num is unnecessary here as it is used only once.
Instead, the value can directly be used in place of the variable.

Signed-off-by: Deepak R Varma <mh12gx2825@gmail.com>
Acked-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: staging: media: imx: remove commented code

The virtual channel is always treated as 0 once the stream enters
CSI's. Commented code in the "#if 0" can be safely removed as it will
not serve any purpose in future.  Issue reported by checkpatch script.

Signed-off-by: Deepak R Varma <mh12gx2825@gmail.com>
Acked-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: rcar-vin: Add support for suspend and resume

Add support for suspend and resume by stopping and starting the video
pipeline while still retaining all buffers given to the driver by
user-space and internally allocated ones, this gives the application a
seamless experience.

Buffers are never returned to user-space unprocessed so user-space don't
notice when suspending. When resuming the driver restarts the capture
session using the internal scratch buffer, this happens before
user-space is unfrozen, this leads to speedy response times once the
application resumes its execution.

As the entire pipeline is stopped on suspend all subdevices in use are
also stopped, and if they enter a shutdown state when not streaming
(such as the R-Car CSI-2 driver) they too will be suspended and resumed
in sync with the VIN driver.

To be able to do keep track of which VINs should be resumed a new
internal state SUSPENDED is added to recode this.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: rcar-vin: Break out hardware start and stop to new methods

To support suspend and resume the ability to start and stop the hardware
needs to be available internally in the driver. Currently this code is
in the start and stop callbacks of the vb2_ops struct. In these
callbacks the code is intertwined with buffer allocation and freeing.

Prepare for suspend and resume support by breaking out the hardware
start/stop code into new methods.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: rcar-vin: Cache the CSI-2 channel selection value

In preparation of suspend/resume support cache the chsel value when
written to the register so it can be restored on resume if needed.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: rcar-vin: Remove handling of user-space buffers when stopping

When returning buffers to user-space it's no longer needed to examine
the buffers given to hardware as recent changes guarantees the only
buffer present in the hardware registers when the driver is not in the
running state is the scratch buffer.

Remove the special case and rename the function to better describe it
now only deals with buffers queued to the driver but not yet recorded in
the hardware registers.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: rcar-vin: Use scratch buffer when not in running state

In its early stages the VIN driver did not use an internal scratch
buffer. This leads to a unnecessary complex start and stop behavior,
specially for TB/BT. The driver now always allocates a scratch buffer to
deal with buffer under-runs, use the scratch buffer to also simplify
starting and stopping.

When capture is starting use the scratch buffer instead of a user-space
buffers while syncing the driver with the hardware state. This allows
the driver to know that no user-space buffer is given to the hardware
before the running state is reached.

When capture is stopping use the scratch buffer instead of leaving the
user-space buffers in place and add a check that all user-space buffers
are processed by the hardware before transitioning from the stopping to
stopped state. This allows the driver to know all user-space buffers
given to the hardware are fully processed.

This change in itself does not improve the driver much but it paves the
way for future simplifications and enhancements. One direct improvement
of this change is that TB/BT buffers returned to user-space while stopping
will always contain both fields, that was not guaranteed before.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: cx231xx: Consolidate dmesg output

The memory allocations in cx231xx_init_*() happen all in task context with
GFP_KERNEL. Therefore a dev_err() trying to deduce whether this is called
from task or interrupt context is pretty useless.

Remove these historical leftovers.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: au0828: Consolidate dmesg output

The memory allocations in au0828_init_isoc() happen all in task context
with GFP_KERNEL. Therefore a printk() trying to deduce whether this is
called from task or interrupt context is pretty useless.

Convert it to au0828_isocdbg() as the other one in that function and for
completeness sake add one for the URB allocation as well.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: Bulk remove BUG_ON(in_interrupt())

None of these BUG_ON()'s is justified. BUG_ON() should only be used when
there is really no way to survive.

If at all these could be replaced by lockdep_assert_preemption_enabled() to
cover all invalid caller context and not just those covered by
in_interrupt().

But all functions which are invoked from those places contain already debug
mechanisms to catch wrong context, so having these extra checks is not
having any advantage.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: mtk-vcodec: add missing put_device() call in mtk_vcodec_release_enc_pm()

mtk_vcodec_release_enc_pm() will be called in two places:

a. mtk_vcodec_init_enc_pm() succeed while mtk_vcodec_probe() return error.
b. mtk_vcodec_enc_remove().

In both cases put_device() call is needed, since of_find_device_by_node()
was called in mtk_vcodec_init_enc_pm() previously.

Thus add put_devices() call in mtk_vcodec_release_enc_pm()

Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: mtk-vcodec: add missing put_device() call in mtk_vcodec_init_enc_pm()

if of_find_device_by_node() succeed, mtk_vcodec_init_enc_pm() doesn't have
a corresponding put_device(). Thus add jump target to fix the exception
handling for this function implementation.

Fixes: 4e855a6efa54 ("[media] vcodec: mediatek: Add Mediatek V4L2 Video Encoder Driver")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: mtk-vcodec: add missing put_device() call in mtk_vcodec_release_dec_pm()

mtk_vcodec_release_dec_pm() will be called in two places:

a. mtk_vcodec_init_dec_pm() succeed while mtk_vcodec_probe() return error.
b. mtk_vcodec_dec_remove().

In both cases put_device() call is needed, since of_find_device_by_node()
was called in mtk_vcodec_init_dec_pm() previously.

Thus add put_devices() call in mtk_vcodec_release_dec_pm()

Fixes: 590577a4e525 ("[media] vcodec: mediatek: Add Mediatek V4L2 Video Decoder Driver")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: mtk-vcodec: add missing put_device() call in mtk_vcodec_init_dec_pm()

if of_find_device_by_node() succeed, mtk_vcodec_init_dec_pm() doesn't have
a corresponding put_device(). Thus add jump target to fix the exception
handling for this function implementation.

Fixes: 590577a4e525 ("[media] vcodec: mediatek: Add Mediatek V4L2 Video Decoder Driver")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: platform: add missing put_device() call in mtk_jpeg_clk_init()

if of_find_device_by_node() succeeds, mtk_jpeg_clk_init() doesn't have
a corresponding put_device(). Thus add put_device() to fix the exception
handling for this function implementation.

Fixes: 648372a87cee ("media: platform: Change the call functions of getting/enable/disable the jpeg's clock")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: cec-core: first mark device unregistered, then wake up fhs

If a CEC device node is unregistered, then it should be marked as
unregistered before waking up any filehandles that are waiting for
an event.

This ensures that there is no race condition where an application can
call CEC_DQEVENT and have the ioctl return 0 instead of ENODEV.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: MAINTAINERS: rectify ZR36067 VIDEO FOR LINUX DRIVER section

Commit 754f0f1ba8d9 ("media: MAINTAINERS: change maintainer of the zoran
driver") added a new section in MAINTAINERS with an invalid file entry
and at the wrong place for alphabetic ordering.

Hence, ./scripts/get_maintainer.pl --self-test=patterns complains:

  warning: no file matches  F:  Documentation/media/v4l-drivers/zoran.rst

Point the file entry to the right location and move the section to the
right place in MAINTAINERS.

Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: pxa_camera: Use fallthrough pseudo-keyword

In order to enable -Wimplicit-fallthrough for Clang[1], replace the
existing /* fall through  */ comments with the new pseudo-keyword
macro fallthrough[2].

[1] https://git.kernel.org/linus/e2079e93f562c7f7a030eb7642017ee5eabaaa10
[2] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through

Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: tm6000: Fix sizeof() mismatches

The are two instances of sizeof() being used incorrectly. The
sizeof(void *) is incorrect because urb_buffer is a char ** pointer,
fix this by using sizeof(*dev->urb_buffer).  The sizeof(dma_addr_t *)
is incorrect, it should be sizeof(*dev->urb_dma), which is a dma_addr_t
and not a dma_addr_t *.  This errors did not cause any issues because
it just so happens the sizes are the same.

Addresses-Coverity: ("Sizeof not portable (SIZEOF_MISMATCH)")

Fixes: 16427faf2867 ("[media] tm6000: Add parameter to keep urb bufs allocated")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: cec-core.rst/cec-ioc-g-mode.rst: fix typos in monitor-all description

cec-core.rst was missing 'are', and cec-ioc-g-mode.rst was missing
a comma.

In both cases this made the description of the Monitor All functionality
hard to read.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: coda: Clarify interrupt registered name

Make interrupt naming more consistent by using a common
pattern for video and jpeg interrupts.

With this commit, interrupts are shown as:

29:          0          0       GPC  12 Level     coda-video
30:          0          0       GPC   3 Level     coda-jpeg

Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: coda: Clarify device registered log

Instead of printing just the device type, let's use
the device name, which makes the message more useful.

With this commit, the messages shown when the driver
is registered are:

coda 2040000.vpu: Firmware code revision: 570363
coda 2040000.vpu: Initialized CODA960.
coda 2040000.vpu: Firmware version: 3.1.1
coda 2040000.vpu: coda-jpeg-encoder registered as video0
coda 2040000.vpu: coda-jpeg-decoder registered as video1
coda 2040000.vpu: coda-video-encoder registered as video2
coda 2040000.vpu: coda-video-decoder registered as video3

Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: coda: Simplify H.264 small buffer padding logic

The H.264 small buffer padding is done under
the (ctx->qsequence == 0 && payload < 512) condition.

Given this is the exact same condition immediately
above, we can move it right there, making the code
slightly clearer.

This change shouldn't affect functionality as it's just
cosmetics.

Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: coda: Remove redundant ctx->initialized setting

The ctx->initialized flag is set in __coda_decoder_seq_init,
so it's redundant to set it in coda_dec_seq_init_work.
Remove the redundant set, which allows to simplify the
implementation quite a bit.

This change shouldn't affect functionality as it's just
cosmetics.

Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: zr364xx: propagate errors from zr364xx_start_readpipe()

zr364xx_start_readpipe() can fail but callers do not care about that.
This can result in various negative consequences. The patch adds missed
error handling.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: saa7164: convert to use DEFINE_SEQ_ATTRIBUTE macro

Use DEFINE_SEQ_ATTRIBUTE macro to simplify the code.

Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: rkvdec: Remove redundant platform_get_irq error message

platform_get_irq() will call dev_err() itself on failure,
so there is no need for the driver to also do this.
This is detected by coccinelle.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

media: staging: rkisp1: remove unecessary clocks

aclk_isp_wrap is a child of aclk_isp, and hclk_isp_wrap is a child of
hclk_isp, thus we can remove parents from the list.

Also, for the isp0, we only need the ISP clock, ACLK and HCLK.
In the future we'll need a pixel clock for RK3288 and RK3399, and a JPEG
clock for RK3288.

So with the goal to cleanup the dt-bindings and remove it from staging,
simplify clock names to isp, aclk and hclk.

Assigned clocks are meant to refer to the full path in the clock tree,
i.e. the leaf in the tree.
For instance, in RK3399, the clock responsible for ACLK (ISP AXI CLOCK)
is aclk_isp0_wrapper.

For reference, this is the isp clock topology on RK3399:

 xin24m
    pll_npll
       npll
          clk_isp1
          clk_isp0
    pll_cpll
       cpll
          aclk_isp1
             aclk_isp1_noc
             hclk_isp1
                aclk_isp1_wrapper
                hclk_isp1_noc
          aclk_isp0
             hclk_isp1_wrapper
             aclk_isp0_wrapper
             aclk_isp0_noc
             hclk_isp0
                hclk_isp0_wrapper
                hclk_isp0_noc
 pclkin_isp1_wrapper

Signed-off-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>