review.tizen.org Git - platform/kernel/linux-starfive.git/log

ahci: Add support for Dell S140 and later controllers

This patch enables support for Dell S140 and later controllers
that use Intel's PCHs configured as PCI_CLASS_STORAGE_RAID.

Reviewed-by: Mika Westerberg <mika.westerberg@intel.com>
Signed-off-by: Charles Rose <charles.rose@dell.com>
Link: https://lore.kernel.org/r/20210615190801.1744466-1-charles.rose@dell.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>

ata: ahci_sunxi: Disable DIPM

DIPM is unsupported or broken on sunxi. Trying to enable the power
management policy med_power_with_dipm on an Allwinner A20 SoC based board
leads to immediate I/O errors and the attached SATA disk disappears from
the /dev filesystem. A reset (power cycle) is required to make the SATA
controller or disk work again. The A10 and A20 SoC data sheets and manuals
don't mention DIPM at all [1], so it's fair to assume that it's simply not
supported. But even if it was, it should be considered broken and best be
disabled in the ahci_sunxi driver.

[1] https://github.com/allwinner-zh/documents/tree/master/

Fixes: c5754b5220f0 ("ARM: sunxi: Add support for Allwinner SUNXi SoCs sata to ahci_platform")
Cc: stable@vger.kernel.org
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Tested-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Link: https://lore.kernel.org/r/20210614072539.3307-1-public_timo.s@silentcreek.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>

m68k/q40: Replace q40ide driver with pata_falcon and falconide

This allows m68k q40 systems to switch from the deprecated IDE subsystem
to libata.

Enhance the byte-swapping falconide and pata_falcon platform drivers to
accept an irq resource, for use on q40. Atari ST-DMA IRQ arrangements seem
to co-exist with q40 IRQ arrangements without too much mess.

The new IO resources were added solely for the purpose of making
request_region() reservations identical to those made by q40ide: these
regions aren't used for actual IO.

Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: Richard Zidlicky <rz@linux-m68k.org>
Reviewed-and-tested-by: Michael Schmitz <schmitzmic@gmail.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Link: https://lore.kernel.org/r/eefb7e9c2291e09fb4e065ce06bc105f05bb9e06.1623287706.git.fthain@linux-m68k.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>

m68k/mac: Replace macide driver with generic platform drivers

This allows m68k mac systems to switch from the deprecated IDE subsystem
to libata.

This was tested on my Quadra 630. I haven't tested it on my PowerBook 150
because I don't have a RAM adapter board for it. It appears that the
hardware I tested doesn't need macide_clear_irq() or macide_test_irq().
If it did, the generic driver would not have worked. It's possible that
those routines are needed for the PowerBook 150 but we can cross that
bridge if and when we come to it.

BTW, macide_clear_irq() appears to suffer from a race condition. The write
to the interrupt flags register could have unintended side effects as it
may alter other flag bits. Fortunately, all of the other bits are unused
by Linux. When tested on my Quadra 630, the assignment *ide_ifr &= ~0x20
was observed to have no effect on bit 5, so it may be redundant anyway.

Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: Joshua Thompson <funaho@jurai.org>
Reviewed-by: Michael Schmitz <schmitzmic@gmail.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Link: https://lore.kernel.org/r/11a56b3317df3bb2ddc15fd29b40b6820e9c7444.1623287706.git.fthain@linux-m68k.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>

pata_ep93xx: fix deferred probing

The driver overrides the error codes returned by platform_get_irq() to
-ENXIO, so if it returns -EPROBE_DEFER, the driver would fail the probe
permanently instead of the deferred probing. Propagate the error code
upstream, as it should have been done from the start...

Fixes: 2fff27512600 ("PATA host controller driver for ep93xx")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Link: https://lore.kernel.org/r/509fda88-2e0d-2cc7-f411-695d7e94b136@omprussia.ru
Signed-off-by: Jens Axboe <axboe@kernel.dk>

pata_octeon_cf: avoid WARN_ON() in ata_host_activate()

Iff platform_get_irq() fails (or returns IRQ0) and thus the polling mode
has to be used, ata_host_activate() hits the WARN_ON() due to 'irq_handler'
parameter being non-NULL if the polling mode is selected. Let's only set
the pointer to the driver's IRQ handler if platform_get_irq() returns a
valid IRQ # -- this should avoid the unnecessary WARN_ON()...

Fixes: 43f01da0f279 ("MIPS/OCTEON/ata: Convert pata_octeon_cf.c to use device tree.")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/3a241167-f84d-1d25-5b9b-be910afbe666@omp.ru
Signed-off-by: Jens Axboe <axboe@kernel.dk>

pata_rb532_cf: fix deferred probing

The driver overrides the error codes returned by platform_get_irq() to
-ENOENT, so if it returns -EPROBE_DEFER, the driver would fail the probe
permanently instead of the deferred probing. Switch to propagating the
error code upstream, still checking/overriding IRQ0 as libata regards it
as "no IRQ" (thus polling) anyway...

Fixes: 9ec36cafe43b ("of/irq: do irq resolution in platform_get_irq")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Link: https://lore.kernel.org/r/771ced55-3efb-21f5-f21c-b99920aae611@omprussia.ru
Signed-off-by: Jens Axboe <axboe@kernel.dk>

sata_highbank: fix deferred probing

The driver overrides the error codes returned by platform_get_irq() to
-EINVAL, so if it returns -EPROBE_DEFER, the driver would fail the probe
permanently instead of the deferred probing. Switch to propagating the
error code upstream, still checking/overriding IRQ0 as libata regards it
as "no IRQ" (thus polling) anyway...

Fixes: 9ec36cafe43b ("of/irq: do irq resolution in platform_get_irq")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Link: https://lore.kernel.org/r/105b456d-1199-f6e9-ceb7-ffc5ba551d1a@omprussia.ru
Signed-off-by: Jens Axboe <axboe@kernel.dk>

sata: nv: fix debug format string mismatch

Turning on debugging in this this driver reveals a type mismatch:

In file included from include/linux/kernel.h:17,
                 from drivers/ata/sata_nv.c:23:
drivers/ata/sata_nv.c: In function 'nv_swncq_sdbfis':
drivers/ata/sata_nv.c:2121:10: error: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'u64' {aka 'long long unsigned int'} [-Werror=format=]
2121 |  DPRINTK("id 0x%x QC: qc_active 0x%x,"
      |          ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
......
2124 |   ap->print_id, ap->qc_active, pp->qc_active,
      |                 ~~~~~~~~~~~~~
      |                   |
      |                   u64 {aka long long unsigned int}
include/linux/printk.h:142:10: note: in definition of macro 'no_printk'
  142 |   printk(fmt, ##__VA_ARGS__);  \
      |          ^~~
drivers/ata/sata_nv.c:2121:2: note: in expansion of macro 'DPRINTK'
2121 |  DPRINTK("id 0x%x QC: qc_active 0x%x,"
      |  ^~~~~~~
drivers/ata/sata_nv.c:2121:36: note: format string is defined here
2121 |  DPRINTK("id 0x%x QC: qc_active 0x%x,"
      |                                   ~^
      |                                    |
      |                                    unsigned int
      |                                   %llx

Use the correct format string for the u64 type.

Fixes: e3ed89396441 ("libata: bump ->qc_active to a 64-bit type")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210514140105.3080580-1-arnd@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>

sata: fsl: fix DPRINTK format string

Printing an __iomem pointer as %x produces a warning:

drivers/ata/sata_fsl.c: In function 'fsl_sata_set_irq_coalescing':
drivers/ata/sata_fsl.c:316:17: error: format '%x' expects argument of type 'unsigned int', but argument 2 has type 'void *' [-Werror=format=]
  316 |         DPRINTK("ICC register status: (hcr base: 0x%x) = 0x%x\n",
      |                 ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
  317 |                         hcr_base, ioread32(hcr_base + ICC));
      |                         ~~~~~~~~
      |                         |
      |                         void *

It's not clear why that pointer should be printed here, but if we do,
then using %p is the way to avoid the warnings.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210514213402.691436-1-arnd@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>

ata: Replace inclusion of kernel.h by bits.h in the header

ata.h uses BIT() macro, hence bits.h must be included. Otherwise
there is no need to have kernel.h included, I do not see any
direct users of it in ata.h. Hence replace inclusion of kernel.h.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210409153456.87798-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Linux 5.13-rc2

Merge tag 'driver-core-5.13-rc2' of git://git./linux/kernel/git/gregkh/driver-core

Pull driver core fixes from Greg KH:
"Here are two driver fixes for driver core changes that happened in
  5.13-rc1.

  The clk driver fix resolves a many-reported issue with booting some
  devices, and the USB typec fix resolves the reported problem of USB
  systems on some embedded boards.

  Both of these have been in linux-next this week with no reported
  issues"

* tag 'driver-core-5.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  clk: Skip clk provider registration when np is NULL
  usb: typec: tcpm: Don't block probing of consumers of "connector" nodes

Merge tag 'staging-5.13-rc2' of git://git./linux/kernel/git/gregkh/staging

Pull staging and IIO driver fixes from Greg KH:
"Here are some small IIO driver fixes and one Staging driver fix for
  5.13-rc2.

  Nothing major, just some resolutions for reported problems:

   - gcc-11 bogus warning fix for rtl8723bs

   - iio driver tiny fixes

  All of these have been in linux-next for many days with no reported
  issues"

* tag 'staging-5.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  iio: tsl2583: Fix division by a zero lux_val
  iio: core: return ENODEV if ioctl is unknown
  iio: core: fix ioctl handlers removal
  iio: gyro: mpu3050: Fix reported temperature value
  iio: hid-sensors: select IIO_TRIGGERED_BUFFER under HID_SENSOR_IIO_TRIGGER
  iio: proximity: pulsedlight: Fix rumtime PM imbalance on error
  iio: light: gp2ap002: Fix rumtime PM imbalance on error
  staging: rtl8723bs: avoid bogus gcc warning

Merge tag 'usb-5.13-rc2' of git://git./linux/kernel/git/gregkh/usb

Pull USB fixes from Greg KH:
"Here are some small USB fixes for 5.13-rc2. They consist of a number
  of resolutions for reported issues:

   - typec fixes for found problems

   - xhci fixes and quirk additions

   - dwc3 driver fixes

   - minor fixes found by Coverity

   - cdc-wdm fixes for reported problems

  All of these have been in linux-next for a few days with no reported
  issues"

* tag 'usb-5.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (28 commits)
  usb: core: hub: fix race condition about TRSMRCY of resume
  usb: typec: tcpm: Fix SINK_DISCOVERY current limit for Rp-default
  xhci: Add reset resume quirk for AMD xhci controller.
  usb: xhci: Increase timeout for HC halt
  xhci: Do not use GFP_KERNEL in (potentially) atomic context
  xhci: Fix giving back cancelled URBs even if halted endpoint can't reset
  xhci-pci: Allow host runtime PM as default for Intel Alder Lake xHCI
  usb: musb: Fix an error message
  usb: typec: tcpm: Fix wrong handling for Not_Supported in VDM AMS
  usb: typec: tcpm: Send DISCOVER_IDENTITY from dedicated work
  usb: typec: ucsi: Retrieve all the PDOs instead of just the first 4
  usb: fotg210-hcd: Fix an error message
  docs: usb: function: Modify path name
  usb: dwc3: omap: improve extcon initialization
  usb: typec: ucsi: Put fwnode in any case during ->probe()
  usb: typec: tcpm: Fix wrong handling in GET_SINK_CAP
  usb: dwc2: Remove obsolete MODULE_ constants from platform.c
  usb: dwc3: imx8mp: fix error return code in dwc3_imx8mp_probe()
  usb: dwc3: imx8mp: detect dwc3 core node via compatible string
  usb: dwc3: gadget: Return success always for kick transfer in ep queue
  ...

Merge tag 'timers-urgent-2021-05-16' of git://git./linux/kernel/git/tip/tip

Pull timer fixes from Thomas Gleixner:
"Two fixes for timers:

   - Use the ALARM feature check in the alarmtimer core code insted of
     the old method of checking for the set_alarm() callback.

     Drivers can have that callback set but the feature bit cleared. If
     such a RTC device is selected then alarms wont work.

   - Use a proper define to let the preprocessor check whether Hyper-V
     VDSO clocksource should be active.

     The code used a constant in an enum with #ifdef, which evaluates to
     always false and disabled the clocksource for VDSO"

* tag 'timers-urgent-2021-05-16' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource/drivers/hyper-v: Re-enable VDSO_CLOCKMODE_HVCLOCK on X86
  alarmtimer: Check RTC features instead of ops

Merge tag 'for-linus-5.13b-rc2-tag' of git://git./linux/kernel/git/xen/tip

Pull xen fixes from Juergen Gross:

- two patches for error path fixes

- a small series for fixing a regression with swiotlb with Xen on Arm

* tag 'for-linus-5.13b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/swiotlb: check if the swiotlb has already been initialized
  arm64: do not set SWIOTLB_NO_FORCE when swiotlb is required
  xen/arm: move xen_swiotlb_detect to arm/swiotlb-xen.h
  xen/unpopulated-alloc: fix error return code in fill_list()
  xen/gntdev: fix gntdev_mmap() error exit path

Merge tag 'x86_urgent_for_v5.13_rc2' of git://git./linux/kernel/git/tip/tip

Pull x86 fixes from Borislav Petkov:
"The three SEV commits are not really urgent material. But we figured
  since getting them in now will avoid a huge amount of conflicts
  between future SEV changes touching tip, the kvm and probably other
  trees, sending them to you now would be best.

  The idea is that the tip, kvm etc branches for 5.14 will all base
  ontop of -rc2 and thus everything will be peachy. What is more, those
  changes are purely mechanical and defines movement so they should be
  fine to go now (famous last words).

  Summary:

   - Enable -Wundef for the compressed kernel build stage

   - Reorganize SEV code to streamline and simplify future development"

* tag 'x86_urgent_for_v5.13_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/boot/compressed: Enable -Wundef
  x86/msr: Rename MSR_K8_SYSCFG to MSR_AMD64_SYSCFG
  x86/sev: Move GHCB MSR protocol and NAE definitions in a common header
  x86/sev-es: Rename sev-es.{ch} to sev.{ch}

Merge tag 'powerpc-5.13-3' of git://git./linux/kernel/git/powerpc/linux

Pull powerpc fixes from Michael Ellerman:

- Fix a regression in the conversion of the 64-bit BookE interrupt
   entry to C.

- Fix KVM hosts running with the hash MMU since the recent KVM gfn
   changes.

- Fix a deadlock in our paravirt spinlocks when hcall tracing is
   enabled.

- Several fixes for oopses in our runtime code patching for security
   mitigations.

- A couple of minor fixes for the recent conversion of 32-bit interrupt
   entry/exit to C.

- Fix __get_user() causing spurious crashes in sigreturn due to a bad
   inline asm constraint, spotted with GCC 11.

- A fix for the way we track IRQ masking state vs NMI interrupts when
   using the new scv system call entry path.

- A couple more minor fixes.

Thanks to Cédric Le Goater, Christian Zigotzky, Christophe Leroy,
Naveen N. Rao, Nicholas Piggin Paul Menzel, and Sean Christopherson.

* tag 'powerpc-5.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/64e/interrupt: Fix nvgprs being clobbered
  powerpc/64s: Make NMI record implicitly soft-masked code as irqs disabled
  powerpc/64s: Fix stf mitigation patching w/strict RWX & hash
  powerpc/64s: Fix entry flush patching w/strict RWX & hash
  powerpc/64s: Fix crashes when toggling entry flush barrier
  powerpc/64s: Fix crashes when toggling stf barrier
  KVM: PPC: Book3S HV: Fix kvm_unmap_gfn_range_hv() for Hash MMU
  powerpc/legacy_serial: Fix UBSAN: array-index-out-of-bounds
  powerpc/signal: Fix possible build failure with unsafe_copy_fpr_{to/from}_user
  powerpc/uaccess: Fix __get_user() with CONFIG_CC_HAS_ASM_GOTO_OUTPUT
  powerpc/pseries: warn if recursing into the hcall tracing code
  powerpc/pseries: use notrace hcall variant for H_CEDE idle
  powerpc/pseries: Don't trace hcall tracing wrapper
  powerpc/pseries: Fix hcall tracing recursion in pv queued spinlocks
  powerpc/syscall: Calling kuap_save_and_lock() is wrong
  powerpc/interrupts: Fix kuep_unlock() call

Merge tag 'sched-urgent-2021-05-15' of git://git./linux/kernel/git/tip/tip

Pull scheduler fixes from Ingo Molnar:
"Fix an idle CPU selection bug, and an AMD Ryzen maximum frequency
  enumeration bug"

* tag 'sched-urgent-2021-05-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, sched: Fix the AMD CPPC maximum performance value on certain AMD Ryzen generations
  sched/fair: Fix clearing of has_idle_cores flag in select_idle_cpu()

Merge tag 'objtool-urgent-2021-05-15' of git://git./linux/kernel/git/tip/tip

Pull objtool fixes from Ingo Molnar:
"Fix a couple of endianness bugs that crept in"

* tag 'objtool-urgent-2021-05-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool/x86: Fix elf_add_alternative() endianness
objtool: Fix elf_create_undef_symbol() endianness

Merge tag 'irq-urgent-2021-05-15' of git://git./linux/kernel/git/tip/tip

Pull irq fix from Ingo Molnar:
"Fix build warning on SH"

* tag 'irq-urgent-2021-05-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sh: Remove unused variable

Merge tag 'core-urgent-2021-05-15' of git://git./linux/kernel/git/tip/tip

Pull x86 stack randomization fix from Ingo Molnar:
"Fix an assembly constraint that affected LLVM up to version 12"

* tag 'core-urgent-2021-05-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
stack: Replace "o" output with "r" input constraint

Merge branch 'akpm' (patches from Andrew)

Merge misc fixes from Andrew Morton:
"13 patches.

  Subsystems affected by this patch series: resource, squashfs, hfsplus,
  modprobe, and mm (hugetlb, slub, userfaultfd, ksm, pagealloc, kasan,
  pagemap, and ioremap)"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  mm/ioremap: fix iomap_max_page_shift
  docs: admin-guide: update description for kernel.modprobe sysctl
  hfsplus: prevent corruption in shrinking truncate
  mm/filemap: fix readahead return types
  kasan: fix unit tests with CONFIG_UBSAN_LOCAL_BOUNDS enabled
  mm: fix struct page layout on 32-bit systems
  ksm: revert "use GET_KSM_PAGE_NOLOCK to get ksm page in remove_rmap_item_from_tree()"
  userfaultfd: release page in error path to avoid BUG_ON
  squashfs: fix divide error in calculate_skip()
  kernel/resource: fix return code check in __request_free_mem_region
  mm, slub: move slub_debug static key enabling outside slab_mutex
  mm/hugetlb: fix cow where page writtable in child
  mm/hugetlb: fix F_SEAL_FUTURE_WRITE

Merge tag 'arc-5.13-rc2' of git://git./linux/kernel/git/vgupta/arc

Pull ARC fixes from Vineet Gupta:

- PAE fixes

- syscall num check off-by-one bug

- misc fixes

* tag 'arc-5.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: mm: Use max_high_pfn as a HIGHMEM zone border
  ARC: mm: PAE: use 40-bit physical page mask
  ARC: entry: fix off-by-one error in syscall number validation
  ARC: kgdb: add 'fallthrough' to prevent a warning
  arc: Fix typos/spellos

Merge tag 'block-5.13-2021-05-14' of git://git.kernel.dk/linux-block

Pull block fixes from Jens Axboe:

- Fix for shared tag set exit (Bart)

- Correct ioctl range for zoned ioctls (Damien)

- Removed dead/unused function (Lin)

- Fix perf regression for shared tags (Ming)

- Fix out-of-bounds issue with kyber and preemption (Omar)

- BFQ merge fix (Paolo)

- Two error handling fixes for nbd (Sun)

- Fix weight update in blk-iocost (Tejun)

- NVMe pull request (Christoph):
      - correct the check for using the inline bio in nvmet (Chaitanya
        Kulkarni)
      - demote unsupported command warnings (Chaitanya Kulkarni)
      - fix corruption due to double initializing ANA state (me, Hou Pu)
      - reset ns->file when open fails (Daniel Wagner)
      - fix a NULL deref when SEND is completed with error in nvmet-rdma
        (Michal Kalderon)

- Fix kernel-doc warning (Bart)

* tag 'block-5.13-2021-05-14' of git://git.kernel.dk/linux-block:
  block/partitions/efi.c: Fix the efi_partition() kernel-doc header
  blk-mq: Swap two calls in blk_mq_exit_queue()
  blk-mq: plug request for shared sbitmap
  nvmet: use new ana_log_size instead the old one
  nvmet: seset ns->file when open fails
  nbd: share nbd_put and return by goto put_nbd
  nbd: Fix NULL pointer in flush_workqueue
  blkdev.h: remove unused codes blk_account_rq
  block, bfq: avoid circular stable merges
  blk-iocost: fix weight updates of inner active iocgs
  nvmet: demote fabrics cmd parse err msg to debug
  nvmet: use helper to remove the duplicate code
  nvmet: demote discovery cmd parse err msg to debug
  nvmet-rdma: Fix NULL deref when SEND is completed with error
  nvmet: fix inline bio check for passthru
  nvmet: fix inline bio check for bdev-ns
  nvme-multipath: fix double initialization of ANA state
  kyber: fix out of bounds access when preempted
  block: uapi: fix comment about block device ioctl

Merge tag 'io_uring-5.13-2021-05-14' of git://git.kernel.dk/linux-block

Pull io_uring fixes from Jens Axboe:
"Just a few minor fixes/changes:

   - Fix issue with double free race for linked timeout completions

   - Fix reference issue with timeouts

   - Remove last few places that make SQPOLL special, since it's just an
     io thread now.

   - Bump maximum allowed registered buffers, as we don't allocate as
     much anymore"

* tag 'io_uring-5.13-2021-05-14' of git://git.kernel.dk/linux-block:
  io_uring: increase max number of reg buffers
  io_uring: further remove sqpoll limits on opcodes
  io_uring: fix ltout double free on completion race
  io_uring: fix link timeout refs

Merge tag 'erofs-for-5.13-rc2-fixes' of git://git./linux/kernel/git/xiang/erofs

Pull erofs fixes from Gao Xiang:
"This mainly fixes 1 lcluster-sized pclusters for the big pcluster
  feature, which can be forcely generated by mkfs as a specific on-disk
  case for per-(sub)file compression strategies but missed to handle in
  runtime properly.

  Also, documentation updates are included to fix the broken
  illustration due to the ReST conversion by accident and complete the
  big pcluster introduction.

  Summary:

   - update documentation to fix the broken illustration due to ReST
     conversion by accident at that time and complete the big pcluster
     introduction

   - fix 1 lcluster-sized pclusters for the big pcluster feature"

* tag 'erofs-for-5.13-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
  erofs: fix 1 lcluster-sized pcluster for big pcluster
  erofs: update documentation about data compression
  erofs: fix broken illustration in documentation

Merge tag 'libnvdimm-fixes-5.13-rc2' of git://git./linux/kernel/git/nvdimm/nvdimm

Pull libnvdimm fixes from Dan Williams:
"A regression fix for a bootup crash condition introduced in this merge
  window and some other minor fixups:

   - Fix regression in ACPI NFIT table handling leading to crashes and
     driver load failures.

   - Move the nvdimm mailing list

   - Miscellaneous minor fixups"

* tag 'libnvdimm-fixes-5.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  ACPI: NFIT: Fix support for variable 'SPA' structure size
  MAINTAINERS: Move nvdimm mailing list
  tools/testing/nvdimm: Make symbol '__nfit_test_ioremap' static
  libnvdimm: Remove duplicate struct declaration

Merge tag 'dax-fixes-5.13-rc2' of git://git./linux/kernel/git/nvdimm/nvdimm

Pull dax fixes from Dan Williams:
"A fix for a hang condition due to missed wakeups in the filesystem-dax
  core when exercised by virtiofs.

  This bug has been there from the beginning, but the condition has
  not triggered on other filesystems since they hold a lock over
  invalidation events"

* tag 'dax-fixes-5.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  dax: Wake up all waiters after invalidating dax entry
  dax: Add a wakeup mode parameter to put_unlocked_entry()
  dax: Add an enum for specifying dax wakup mode

Merge tag 'drm-fixes-2021-05-15' of git://anongit.freedesktop.org/drm/drm

Pull more drm fixes from Dave Airlie:
"Looks like I wasn't the only one not fully switched on this week. The
  msm pull has a missing tag so I missed it, and i915 team were a bit
  late. In my defence I did have a day with the roof of my home office
  removed, so was sitting at my kids desk.

  msm:
   - dsi regression fix
   - dma-buf pinning fix
   - displayport fixes
   - llc fix

  i915:
   - Fix active callback alignment annotations and subsequent crashes
   - Retract link training strategy to slow and wide, again
   - Avoid division by zero on gen2
   - Use correct width reads for C0DRB3/C1DRB3 registers
   - Fix double free in pdp allocation failure path
   - Fix HDMI 2.1 PCON downstream caps check"

* tag 'drm-fixes-2021-05-15' of git://anongit.freedesktop.org/drm/drm:
  drm/i915: Use correct downstream caps for check Src-Ctl mode for PCON
  drm/i915/overlay: Fix active retire callback alignment
  drm/i915: Fix crash in auto_retire
  drm/i915/gt: Fix a double free in gen8_preallocate_top_level_pdp
  drm/i915: Read C0DRB3/C1DRB3 as 16 bits again
  drm/i915: Avoid div-by-zero on gen2
  drm/i915/dp: Use slow and wide link training for everything
  drm/msm/dp: initialize audio_comp when audio starts
  drm/msm/dp: check sink_count before update is_connected status
  drm/msm: fix minor version to indicate MSM_PARAM_SUSPENDS support
  drm/msm/dsi: fix msm_dsi_phy_get_clk_provider return code
  drm/msm/dsi: dsi_phy_28nm_8960: fix uninitialized variable access
  drm/msm: fix LLC not being enabled for mmu500 targets
  drm/msm: Do not unpin/evict exported dma-buf's

tty: vt: always invoke vc->vc_sw->con_resize callback

syzbot is reporting OOB write at vga16fb_imageblit() [1], for
resize_screen() from ioctl(VT_RESIZE) returns 0 without checking whether
requested rows/columns fit the amount of memory reserved for the graphical
screen if current mode is KD_GRAPHICS.

----------
  #include <sys/types.h>
  #include <sys/stat.h>
  #include <fcntl.h>
  #include <sys/ioctl.h>
  #include <linux/kd.h>
  #include <linux/vt.h>

  int main(int argc, char *argv[])
  {
        const int fd = open("/dev/char/4:1", O_RDWR);
        struct vt_sizes vt = { 0x4100, 2 };

        ioctl(fd, KDSETMODE, KD_GRAPHICS);
        ioctl(fd, VT_RESIZE, &vt);
        ioctl(fd, KDSETMODE, KD_TEXT);
        return 0;
  }
----------

Allow framebuffer drivers to return -EINVAL, by moving vc->vc_mode !=
KD_GRAPHICS check from resize_screen() to fbcon_resize().

Link: https://syzkaller.appspot.com/bug?extid=1f29e126cf461c4de3b3
Reported-by: syzbot <syzbot+1f29e126cf461c4de3b3@syzkaller.appspotmail.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Tested-by: syzbot <syzbot+1f29e126cf461c4de3b3@syzkaller.appspotmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/ioremap: fix iomap_max_page_shift

iomap_max_page_shift is expected to contain a page shift, so it can't be a
'bool', has to be an 'unsigned int'

And fix the default values: P4D_SHIFT is when huge iomap is allowed.

However, on some architectures (eg: powerpc book3s/64), P4D_SHIFT is not a
constant so it can't be used to initialise a static variable. So,
initialise iomap_max_page_shift with a maximum shift supported by the
architecture, it is gated by P4D_SHIFT in vmap_try_huge_p4d() anyway.

Link: https://lkml.kernel.org/r/ad2d366015794a9f21320dcbdd0a8eb98979e9df.1620898113.git.christophe.leroy@csgroup.eu
Fixes: bbc180a5adb0 ("mm: HUGE_VMAP arch support cleanup")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

docs: admin-guide: update description for kernel.modprobe sysctl

When I added CONFIG_MODPROBE_PATH, I neglected to update Documentation/.
It's still true that this defaults to /sbin/modprobe, but now via a level
of indirection. So document that the kernel might have been built with
something other than /sbin/modprobe as the initial value.

Link: https://lkml.kernel.org/r/20210420125324.1246826-1-linux@rasmusvillemoes.dk
Fixes: 17652f4240f7a ("modules: add CONFIG_MODPROBE_PATH")
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jessica Yu <jeyu@kernel.org>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

hfsplus: prevent corruption in shrinking truncate

I believe there are some issues introduced by commit 31651c607151
("hfsplus: avoid deadlock on file truncation")

HFS+ has extent records which always contains 8 extents.  In case the
first extent record in catalog file gets full, new ones are allocated from
extents overflow file.

In case shrinking truncate happens to middle of an extent record which
locates in extents overflow file, the logic in hfsplus_file_truncate() was
changed so that call to hfs_brec_remove() is not guarded any more.

Right action would be just freeing the extents that exceed the new size
inside extent record by calling hfsplus_free_extents(), and then check if
the whole extent record should be removed.  However since the guard
(blk_cnt > start) is now after the call to hfs_brec_remove(), this has
unfortunate effect that the last matching extent record is removed
unconditionally.

To reproduce this issue, create a file which has at least 10 extents, and
then perform shrinking truncate into middle of the last extent record, so
that the number of remaining extents is not under or divisible by 8.  This
causes the last extent record (8 extents) to be removed totally instead of
truncating into middle of it.  Thus this causes corruption, and lost data.

Fix for this is simply checking if the new truncated end is below the
start of this extent record, making it safe to remove the full extent
record.  However call to hfs_brec_remove() can't be moved to it's previous
place since we're dropping ->tree_lock and it can cause a race condition
and the cached info being invalidated possibly corrupting the node data.

Another issue is related to this one.  When entering into the block
(blk_cnt > start) we are not holding the ->tree_lock.  We break out from
the loop not holding the lock, but hfs_find_exit() does unlock it.  Not
sure if it's possible for someone else to take the lock under our feet,
but it can cause hard to debug errors and premature unlocking.  Even if
there's no real risk of it, the locking should still always be kept in
balance.  Thus taking the lock now just before the check.

Link: https://lkml.kernel.org/r/20210429165139.3082828-1-jouni.roivas@tuxera.com
Fixes: 31651c607151f ("hfsplus: avoid deadlock on file truncation")
Signed-off-by: Jouni Roivas <jouni.roivas@tuxera.com>
Reviewed-by: Anton Altaparmakov <anton@tuxera.com>
Cc: Anatoly Trosinenko <anatoly.trosinenko@gmail.com>
Cc: Viacheslav Dubeyko <slava@dubeyko.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/filemap: fix readahead return types

A readahead request will not allocate more memory than can be represented
by a size_t, even on systems that have HIGHMEM available. Change the
length functions from returning an loff_t to a size_t.

Link: https://lkml.kernel.org/r/20210510201201.1558972-1-willy@infradead.org
Fixes: 32c0a6bcaa1f57 ("btrfs: add and use readahead_batch_length")
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kasan: fix unit tests with CONFIG_UBSAN_LOCAL_BOUNDS enabled

These tests deliberately access these arrays out of bounds, which will
cause the dynamic local bounds checks inserted by
CONFIG_UBSAN_LOCAL_BOUNDS to fail and panic the kernel. To avoid this
problem, access the arrays via volatile pointers, which will prevent the
compiler from being able to determine the array bounds.

These accesses use volatile pointers to char (char *volatile) rather than
the more conventional pointers to volatile char (volatile char *) because
we want to prevent the compiler from making inferences about the pointer
itself (i.e. its array bounds), not the data that it refers to.

Link: https://lkml.kernel.org/r/20210507025915.1464056-1-pcc@google.com
Link: https://linux-review.googlesource.com/id/I90b1713fbfa1bf68ff895aef099ea77b98a7c3b9
Signed-off-by: Peter Collingbourne <pcc@google.com>
Tested-by: Alexander Potapenko <glider@google.com>
Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Peter Collingbourne <pcc@google.com>
Cc: George Popescu <georgepope@android.com>
Cc: Elena Petrova <lenaptr@google.com>
Cc: Evgenii Stepanov <eugenis@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: fix struct page layout on 32-bit systems

32-bit architectures which expect 8-byte alignment for 8-byte integers and
need 64-bit DMA addresses (arm, mips, ppc) had their struct page
inadvertently expanded in 2019.  When the dma_addr_t was added, it forced
the alignment of the union to 8 bytes, which inserted a 4 byte gap between
'flags' and the union.

Fix this by storing the dma_addr_t in one or two adjacent unsigned longs.
This restores the alignment to that of an unsigned long.  We always
store the low bits in the first word to prevent the PageTail bit from
being inadvertently set on a big endian platform.  If that happened,
get_user_pages_fast() racing against a page which was freed and
reallocated to the page_pool could dereference a bogus compound_head(),
which would be hard to trace back to this cause.

Link: https://lkml.kernel.org/r/20210510153211.1504886-1-willy@infradead.org
Fixes: c25fff7171be ("mm: add dma_addr_t to struct page")
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Tested-by: Matteo Croce <mcroce@linux.microsoft.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ksm: revert "use GET_KSM_PAGE_NOLOCK to get ksm page in remove_rmap_item_from_tree()"

This reverts commit 3e96b6a2e9ad929a3230a22f4d64a74671a0720b. General
Protection Fault in rmap_walk_ksm() under memory pressure:
remove_rmap_item_from_tree() needs to take page lock, of course.

Link: https://lkml.kernel.org/r/alpine.LSU.2.11.2105092253500.1127@eggly.anvils
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

userfaultfd: release page in error path to avoid BUG_ON

Consider the following sequence of events:

1. Userspace issues a UFFD ioctl, which ends up calling into
   shmem_mfill_atomic_pte(). We successfully account the blocks, we
   shmem_alloc_page(), but then the copy_from_user() fails. We return
   -ENOENT. We don't release the page we allocated.
2. Our caller detects this error code, tries the copy_from_user() after
   dropping the mmap_lock, and retries, calling back into
   shmem_mfill_atomic_pte().
3. Meanwhile, let's say another process filled up the tmpfs being used.
4. So shmem_mfill_atomic_pte() fails to account blocks this time, and
   immediately returns - without releasing the page.

This triggers a BUG_ON in our caller, which asserts that the page
should always be consumed, unless -ENOENT is returned.

To fix this, detect if we have such a "dangling" page when accounting
fails, and if so, release it before returning.

Link: https://lkml.kernel.org/r/20210428230858.348400-1-axelrasmussen@google.com
Fixes: cb658a453b93 ("userfaultfd: shmem: avoid leaking blocks and used blocks in UFFDIO_COPY")
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Reported-by: Hugh Dickins <hughd@google.com>
Acked-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

squashfs: fix divide error in calculate_skip()

Sysbot has reported a "divide error" which has been identified as being
caused by a corrupted file_size value within the file inode.  This value
has been corrupted to a much larger value than expected.

Calculate_skip() is passed i_size_read(inode) >> msblk->block_log.  Due to
the file_size value corruption this overflows the int argument/variable in
that function, leading to the divide error.

This patch changes the function to use u64.  This will accommodate any
unexpectedly large values due to corruption.

The value returned from calculate_skip() is clamped to be never more than
SQUASHFS_CACHED_BLKS - 1, or 7.  So file_size corruption does not lead to
an unexpectedly large return result here.

Link: https://lkml.kernel.org/r/20210507152618.9447-1-phillip@squashfs.org.uk
Signed-off-by: Phillip Lougher <phillip@squashfs.org.uk>
Reported-by: <syzbot+e8f781243ce16ac2f962@syzkaller.appspotmail.com>
Reported-by: <syzbot+7b98870d4fec9447b951@syzkaller.appspotmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel/resource: fix return code check in __request_free_mem_region

Splitting an earlier version of a patch that allowed calling
__request_region() while holding the resource lock into a series of
patches required changing the return code for the newly introduced
__request_region_locked().

Unfortunately this change was not carried through to a subsequent commit
56fd94919b8b ("kernel/resource: fix locking in request_free_mem_region")
in the series. This resulted in a use-after-free due to freeing the
struct resource without properly releasing it. Fix this by correcting the
return code check so that the struct is not freed if the request to add it
was successful.

Link: https://lkml.kernel.org/r/20210512073528.22334-1-apopple@nvidia.com
Fixes: 56fd94919b8b ("kernel/resource: fix locking in request_free_mem_region")
Signed-off-by: Alistair Popple <apopple@nvidia.com>
Reported-by: kernel test robot <oliver.sang@intel.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Muchun Song <smuchun@gmail.com>
Cc: Oliver Sang <oliver.sang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm, slub: move slub_debug static key enabling outside slab_mutex

Paul E.  McKenney reported [1] that commit 1f0723a4c0df ("mm, slub: enable
slub_debug static key when creating cache with explicit debug flags")
results in the lockdep complaint:

======================================================
WARNING: possible circular locking dependency detected
5.12.0+ #15 Not tainted
------------------------------------------------------
rcu_torture_sta/109 is trying to acquire lock:
ffffffff96063cd0 (cpu_hotplug_lock){++++}-{0:0}, at: static_key_enable+0x9/0x20

but task is already holding lock:
ffffffff96173c28 (slab_mutex){+.+.}-{3:3}, at: kmem_cache_create_usercopy+0x2d/0x250

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #1 (slab_mutex){+.+.}-{3:3}:
        lock_acquire+0xb9/0x3a0
        __mutex_lock+0x8d/0x920
        slub_cpu_dead+0x15/0xf0
        cpuhp_invoke_callback+0x17a/0x7c0
        cpuhp_invoke_callback_range+0x3b/0x80
        _cpu_down+0xdf/0x2a0
        cpu_down+0x2c/0x50
        device_offline+0x82/0xb0
        remove_cpu+0x1a/0x30
        torture_offline+0x80/0x140
        torture_onoff+0x147/0x260
        kthread+0x10a/0x140
        ret_from_fork+0x22/0x30

-> #0 (cpu_hotplug_lock){++++}-{0:0}:
        check_prev_add+0x8f/0xbf0
        __lock_acquire+0x13f0/0x1d80
        lock_acquire+0xb9/0x3a0
        cpus_read_lock+0x21/0xa0
        static_key_enable+0x9/0x20
        __kmem_cache_create+0x38d/0x430
        kmem_cache_create_usercopy+0x146/0x250
        kmem_cache_create+0xd/0x10
        rcu_torture_stats+0x79/0x280
        kthread+0x10a/0x140
        ret_from_fork+0x22/0x30

other info that might help us debug this:

  Possible unsafe locking scenario:

        CPU0                    CPU1
        ----                    ----
   lock(slab_mutex);
                                lock(cpu_hotplug_lock);
                                lock(slab_mutex);
   lock(cpu_hotplug_lock);

  *** DEADLOCK ***

1 lock held by rcu_torture_sta/109:
  #0: ffffffff96173c28 (slab_mutex){+.+.}-{3:3}, at: kmem_cache_create_usercopy+0x2d/0x250

stack backtrace:
CPU: 3 PID: 109 Comm: rcu_torture_sta Not tainted 5.12.0+ #15
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.13.0-1ubuntu1.1 04/01/2014
Call Trace:
  dump_stack+0x6d/0x89
  check_noncircular+0xfe/0x110
  ? lock_is_held_type+0x98/0x110
  check_prev_add+0x8f/0xbf0
  __lock_acquire+0x13f0/0x1d80
  lock_acquire+0xb9/0x3a0
  ? static_key_enable+0x9/0x20
  ? mark_held_locks+0x49/0x70
  cpus_read_lock+0x21/0xa0
  ? static_key_enable+0x9/0x20
  static_key_enable+0x9/0x20
  __kmem_cache_create+0x38d/0x430
  kmem_cache_create_usercopy+0x146/0x250
  ? rcu_torture_stats_print+0xd0/0xd0
  kmem_cache_create+0xd/0x10
  rcu_torture_stats+0x79/0x280
  ? rcu_torture_stats_print+0xd0/0xd0
  kthread+0x10a/0x140
  ? kthread_park+0x80/0x80
  ret_from_fork+0x22/0x30

This is because there's one order of locking from the hotplug callbacks:

lock(cpu_hotplug_lock); // from hotplug machinery itself
lock(slab_mutex); // in e.g. slab_mem_going_offline_callback()

And commit 1f0723a4c0df made the reverse sequence possible:
lock(slab_mutex); // in kmem_cache_create_usercopy()
lock(cpu_hotplug_lock); // kmem_cache_open() -> static_key_enable()

The simplest fix is to move static_key_enable() to a place before slab_mutex is
taken. That means kmem_cache_create_usercopy() in mm/slab_common.c which is not
ideal for SLUB-specific code, but the #ifdef CONFIG_SLUB_DEBUG makes it
at least self-contained and obvious.

[1] https://lore.kernel.org/lkml/20210502171827.GA3670492@paulmck-ThinkPad-P17-Gen-1/

Link: https://lkml.kernel.org/r/20210504120019.26791-1-vbabka@suse.cz
Fixes: 1f0723a4c0df ("mm, slub: enable slub_debug static key when creating cache with explicit debug flags")
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: Paul E. McKenney <paulmck@kernel.org>
Tested-by: Paul E. McKenney <paulmck@kernel.org>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/hugetlb: fix cow where page writtable in child

When rework early cow of pinned hugetlb pages, we moved huge_ptep_get()
upper but overlooked a side effect that the huge_ptep_get() will fetch the
pte after wr-protection. After moving it upwards, we need explicit
wr-protect of child pte or we will keep the write bit set in the child
process, which could cause data corrution where the child can write to the
original page directly.

This issue can also be exposed by "memfd_test hugetlbfs" kselftest.

Link: https://lkml.kernel.org/r/20210503234356.9097-3-peterx@redhat.com
Fixes: 4eae4efa2c299 ("hugetlb: do early cow when page pinned on src mm")
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Joel Fernandes (Google) <joel@joelfernandes.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/hugetlb: fix F_SEAL_FUTURE_WRITE

Patch series "mm/hugetlb: Fix issues on file sealing and fork", v2.

Hugh reported issue with F_SEAL_FUTURE_WRITE not applied correctly to
hugetlbfs, which I can easily verify using the memfd_test program, which
seems that the program is hardly run with hugetlbfs pages (as by default
shmem).

Meanwhile I found another probably even more severe issue on that hugetlb
fork won't wr-protect child cow pages, so child can potentially write to
parent private pages. Patch 2 addresses that.

After this series applied, "memfd_test hugetlbfs" should start to pass.

This patch (of 2):

F_SEAL_FUTURE_WRITE is missing for hugetlb starting from the first day.
There is a test program for that and it fails constantly.

$ ./memfd_test hugetlbfs
memfd-hugetlb: CREATE
memfd-hugetlb: BASIC
memfd-hugetlb: SEAL-WRITE
memfd-hugetlb: SEAL-FUTURE-WRITE
mmap() didn't fail as expected
Aborted (core dumped)

I think it's probably because no one is really running the hugetlbfs test.

Fix it by checking FUTURE_WRITE also in hugetlbfs_file_mmap() as what we
do in shmem_mmap(). Generalize a helper for that.

Link: https://lkml.kernel.org/r/20210503234356.9097-1-peterx@redhat.com
Link: https://lkml.kernel.org/r/20210503234356.9097-2-peterx@redhat.com
Fixes: ab3948f58ff84 ("mm/memfd: add an F_SEAL_FUTURE_WRITE seal to memfd")
Signed-off-by: Peter Xu <peterx@redhat.com>
Reported-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Joel Fernandes (Google) <joel@joelfernandes.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'drm-msm-fixes-2021-05-09' of https://gitlab.freedesktop.org/drm/msm into drm-fixes

- dsi regression fix
- dma-buf pinning fix
- displayport fixes
- llc fix

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGuqLZDAEJwUFKb6m+h3kyxgjDEKa3DPA1fHA69vxbXH=g@mail.gmail.com

Merge tag 'trace-v5.13-rc1' of git://git./linux/kernel/git/rostedt/linux-trace

Pull tracing fix from Steven Rostedt:
"Fix trace_check_vprintf() for %.*s

  The sanity check of all strings being read from the ring buffer to
  make sure they are in safe memory space did not account for the %.*s
  notation having another parameter to process (the length).

  Add that to the check"

* tag 'trace-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Handle %.*s in trace_check_vprintf()

Merge tag 'drm-intel-fixes-2021-05-14' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes

drm/i915 fixes for v5.13-rc2:
- Fix active callback alignment annotations and subsequent crashes
- Retract link training strategy to slow and wide, again
- Avoid division by zero on gen2
- Use correct width reads for C0DRB3/C1DRB3 registers
- Fix double free in pdp allocation failure path
- Fix HDMI 2.1 PCON downstream caps check

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87a6oxu9ao.fsf@intel.com

Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux

Pull arm64 fixes from Catalin Marinas:
"Fixes and cpucaps.h automatic generation:

   - Generate cpucaps.h at build time rather than carrying lots of
     #defines. Merged at -rc1 to avoid some conflicts during the merge
     window.

   - Initialise RGSR_EL1.SEED in __cpu_setup() as it may be left as 0
     out of reset and the IRG instruction would not function as expected
     if only the architected pseudorandom number generator is
     implemented.

   - Fix potential race condition in __sync_icache_dcache() where the
     PG_dcache_clean page flag is set before the actual cache
     maintenance.

   - Fix header include in BTI kselftests"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: Fix race condition on PG_dcache_clean in __sync_icache_dcache()
  arm64: tools: Add __ASM_CPUCAPS_H to the endif in cpucaps.h
  arm64: mte: initialize RGSR_EL1.SEED in __cpu_setup
  kselftest/arm64: Add missing stddef.h include to BTI tests
  arm64: Generate cpucaps.h

Merge tag 'f2fs-5.13-rc1-fix' of git://git./linux/kernel/git/jaegeuk/f2fs

Pull f2fs fixes from Jaegeuk Kim:
"This fixes some critical bugs such as memory leak in compression
  flows, kernel panic when handling errors, and swapon failure due to
  newly added condition check"

* tag 'f2fs-5.13-rc1-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs:
  f2fs: return EINVAL for hole cases in swap file
  f2fs: avoid swapon failure by giving a warning first
  f2fs: compress: fix to assign cc.cluster_idx correctly
  f2fs: compress: fix race condition of overwrite vs truncate
  f2fs: compress: fix to free compress page correctly
  f2fs: support iflag change given the mask
  f2fs: avoid null pointer access when handling IPU error

Merge tag 'drm-fixes-2021-05-14' of git://anongit.freedesktop.org/drm/drm

Pull drm fixes from Dave Airlie:
"Not much here, mostly amdgpu fixes, with a couple of radeon, and a
  cosmetic vc4.

  Two MAINTAINERS file updates also.

  amdgpu:
   - Fixes for flexible array conversions
   - Fix sysfs attribute init
   - Harvesting fixes
   - VCN CG/PG fixes for Picasso

  radeon:
   - Fixes for flexible array conversions
   - Fix for flickering on Oland with multiple 4K displays

  vc4:
   - drop unused function"

* tag 'drm-fixes-2021-05-14' of git://anongit.freedesktop.org/drm/drm:
  drm/amdgpu: update vcn1.0 Non-DPG suspend sequence
  drm/amdgpu: set vcn mgcg flag for picasso
  drm/radeon/dpm: Disable sclk switching on Oland when two 4K 60Hz monitors are connected
  drm/amdgpu: update the method for harvest IP for specific SKU
  drm/amdgpu: add judgement when add ip blocks (v2)
  drm/amd/display: Initialize attribute for hdcp_srm sysfs file
  drm/amd/pm: Fix out-of-bounds bug
  drm/radeon/si_dpm: Fix SMU power state load
  drm/radeon/ni_dpm: Fix booting bug
  MAINTAINERS: Update address for Emma Anholt
  MAINTAINERS: Update my e-mail
  drm/vc4: remove unused function
  drm/ttm: Do not add non-system domain BO into swap list

arm64: Fix race condition on PG_dcache_clean in __sync_icache_dcache()

To ensure that instructions are observable in a new mapping, the arm64
set_pte_at() implementation cleans the D-cache and invalidates the
I-cache to the PoU. As an optimisation, this is only done on executable
mappings and the PG_dcache_clean page flag is set to avoid future cache
maintenance on the same page.

When two different processes map the same page (e.g. private executable
file or shared mapping) there's a potential race on checking and setting
PG_dcache_clean via set_pte_at() -> __sync_icache_dcache(). While on the
fault paths the page is locked (PG_locked), mprotect() does not take the
page lock. The result is that one process may see the PG_dcache_clean
flag set but the I/D cache maintenance not yet performed.

Avoid test_and_set_bit(PG_dcache_clean) in favour of separate test_bit()
and set_bit(). In the rare event of a race, the cache maintenance is
done twice.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: <stable@vger.kernel.org>
Cc: Will Deacon <will@kernel.org>
Cc: Steven Price <steven.price@arm.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210514095001.13236-1-catalin.marinas@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

block/partitions/efi.c: Fix the efi_partition() kernel-doc header

Fix the following kernel-doc warning:

block/partitions/efi.c:685: warning: wrong kernel-doc identifier on line:
* efi_partition(struct parsed_partitions *state)

Cc: Alexander Viro <viro@math.psu.edu>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20210513171708.8391-1-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>

blk-mq: Swap two calls in blk_mq_exit_queue()

If a tag set is shared across request queues (e.g. SCSI LUNs) then the
block layer core keeps track of the number of active request queues in
tags->active_queues. blk_mq_tag_busy() and blk_mq_tag_idle() update that
atomic counter if the hctx flag BLK_MQ_F_TAG_QUEUE_SHARED is set. Make
sure that blk_mq_exit_queue() calls blk_mq_tag_idle() before that flag is
cleared by blk_mq_del_queue_tag_set().

Cc: Christoph Hellwig <hch@infradead.org>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Fixes: 0d2602ca30e4 ("blk-mq: improve support for shared tags maps")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20210513171529.7977-1-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>

blk-mq: plug request for shared sbitmap

In case of shared sbitmap, request won't be held in plug list any more
sine commit 32bc15afed04 ("blk-mq: Facilitate a shared sbitmap per
tagset"), this way makes request merge from flush plug list & batching
submission not possible, so cause performance regression.

Yanhui reports performance regression when running sequential IO
test(libaio, 16 jobs, 8 depth for each job) in VM, and the VM disk
is emulated with image stored on xfs/megaraid_sas.

Fix the issue by recovering original behavior to allow to hold request
in plug list.

Cc: Yanhui Ma <yama@redhat.com>
Cc: John Garry <john.garry@huawei.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: kashyap.desai@broadcom.com
Fixes: 32bc15afed04 ("blk-mq: Facilitate a shared sbitmap per tagset")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20210514022052.1047665-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>

xen/swiotlb: check if the swiotlb has already been initialized

xen_swiotlb_init calls swiotlb_late_init_with_tbl, which fails with
-ENOMEM if the swiotlb has already been initialized.

Add an explicit check io_tlb_default_mem != NULL at the beginning of
xen_swiotlb_init. If the swiotlb is already initialized print a warning
and return -EEXIST.

On x86, the error propagates.

On ARM, we don't actually need a special swiotlb buffer (yet), any
buffer would do. So ignore the error and continue.

CC: boris.ostrovsky@oracle.com
CC: jgross@suse.com
Signed-off-by: Stefano Stabellini <stefano.stabellini@xilinx.com>
Reviewed-by: Boris Ostrovsky <boris.ostrvsky@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210512201823.1963-3-sstabellini@kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>

arm64: do not set SWIOTLB_NO_FORCE when swiotlb is required

Although SWIOTLB_NO_FORCE is meant to allow later calls to swiotlb_init,
today dma_direct_map_page returns error if SWIOTLB_NO_FORCE.

For now, without a larger overhaul of SWIOTLB_NO_FORCE, the best we can
do is to avoid setting SWIOTLB_NO_FORCE in mem_init when we know that it
is going to be required later (e.g. Xen requires it).

CC: boris.ostrovsky@oracle.com
CC: jgross@suse.com
CC: catalin.marinas@arm.com
CC: will@kernel.org
CC: linux-arm-kernel@lists.infradead.org
Fixes: 2726bf3ff252 ("swiotlb: Make SWIOTLB_NO_FORCE perform no allocation")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Stefano Stabellini <stefano.stabellini@xilinx.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20210512201823.1963-2-sstabellini@kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>

xen/arm: move xen_swiotlb_detect to arm/swiotlb-xen.h

Move xen_swiotlb_detect to a static inline function to make it available
to !CONFIG_XEN builds.

CC: boris.ostrovsky@oracle.com
CC: jgross@suse.com
Signed-off-by: Stefano Stabellini <stefano.stabellini@xilinx.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20210512201823.1963-1-sstabellini@kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>

clocksource/drivers/hyper-v: Re-enable VDSO_CLOCKMODE_HVCLOCK on X86

Mohammed reports (https://bugzilla.kernel.org/show_bug.cgi?id=213029)
the commit e4ab4658f1cf ("clocksource/drivers/hyper-v: Handle vDSO
differences inline") broke vDSO on x86. The problem appears to be that
VDSO_CLOCKMODE_HVCLOCK is an enum value in 'enum vdso_clock_mode' and
'#ifdef VDSO_CLOCKMODE_HVCLOCK' branch evaluates to false (it is not
a define).

Use a dedicated HAVE_VDSO_CLOCKMODE_HVCLOCK define instead.

Fixes: e4ab4658f1cf ("clocksource/drivers/hyper-v: Handle vDSO differences inline")
Reported-by: Mohammed Gamal <mgamal@redhat.com>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20210513073246.1715070-1-vkuznets@redhat.com

io_uring: increase max number of reg buffers

Since recent changes instead of storing a large array of struct
io_mapped_ubuf, we store pointers to them, that is 4 times slimmer and
we should not to so worry about restricting max number of registererd
buffer slots, increase the limit 4 times.

Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/d3dee1da37f46da416aa96a16bf9e5094e10584d.1620990371.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>

io_uring: further remove sqpoll limits on opcodes

There are three types of requests that left disabled for sqpoll, namely
epoll ctx, statx, and resources update. Since SQPOLL task is now closely
mimics a userspace thread, remove the restrictions.

Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/909b52d70c45636d8d7897582474ea5aab5eed34.1620990306.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>

io_uring: fix ltout double free on completion race

Always remove linked timeout on io_link_timeout_fn() from the master
request link list, otherwise we may get use-after-free when first
io_link_timeout_fn() puts linked timeout in the fail path, and then
will be found and put on master's free.

Cc: stable@vger.kernel.org # 5.10+
Fixes: 90cd7e424969d ("io_uring: track link timeout's master explicitly")
Reported-and-tested-by: syzbot+5a864149dd970b546223@syzkaller.appspotmail.com
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/69c46bf6ce37fec4fdcd98f0882e18eb07ce693a.1620990121.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>

powerpc/64e/interrupt: Fix nvgprs being clobbered

Some interrupt handlers have an "extra" that saves 1 or 2
registers (r14, r15) in the paca save area and makes them available to
use by the handler.

The change to always save nvgprs in exception handlers lead to some
interrupt handlers saving those scratch r14 / r15 registers into the
interrupt frame's GPR saves, which get restored on interrupt exit.

Fix this by always reloading those scratch registers from paca before
the EXCEPTION_COMMON that saves nvgprs.

Fixes: 4228b2c3d20e ("powerpc/64e/interrupt: always save nvgprs on interrupt")
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210514044008.1955783-1-npiggin@gmail.com

powerpc/64s: Make NMI record implicitly soft-masked code as irqs disabled

scv support introduced the notion of code that implicitly soft-masks
irqs due to the instruction addresses. This is required because scv
enters the kernel with MSR[EE]=1.

If a NMI (including soft-NMI) interrupt hits when we are implicitly
soft-masked then its regs->softe does not reflect this because it is
derived from the explicit soft mask state (paca->irq_soft_mask). This
makes arch_irq_disabled_regs(regs) return false.

This can trigger a warning in the soft-NMI watchdog code (shown below).
Fix it by having NMI interrupts set regs->softe to disabled in case of
interrupting an implicit soft-masked region.

  ------------[ cut here ]------------
  WARNING: CPU: 41 PID: 1103 at arch/powerpc/kernel/watchdog.c:259 soft_nmi_interrupt+0x3e4/0x5f0
  CPU: 41 PID: 1103 Comm: (spawn) Not tainted
  NIP:  c000000000039534 LR: c000000000039234 CTR: c000000000009a00
  REGS: c000007fffbcf940 TRAP: 0700   Not tainted
  MSR:  9000000000021033 <SF,HV,ME,IR,DR,RI,LE>  CR: 22042482  XER: 200400ad
  CFAR: c000000000039260 IRQMASK: 3
  GPR00: c000000000039204 c000007fffbcfbe0 c000000001d6c300 0000000000000003
  GPR04: 00007ffffa45d078 0000000000000000 0000000000000008 0000000000000020
  GPR08: 0000007ffd4e0000 0000000000000000 c000007ffffceb00 7265677368657265
  GPR12: 9000000000009033 c000007ffffceb00 00000f7075bf4480 000000000000002a
  GPR16: 00000f705745a528 00007ffffa45ddd8 00000f70574d0008 0000000000000000
  GPR20: 00000f7075c58d70 00000f7057459c38 0000000000000001 0000000000000040
  GPR24: 0000000000000000 0000000000000029 c000000001dae058 0000000000000029
  GPR28: 0000000000000000 0000000000000800 0000000000000009 c000007fffbcfd60
  NIP [c000000000039534] soft_nmi_interrupt+0x3e4/0x5f0
  LR [c000000000039234] soft_nmi_interrupt+0xe4/0x5f0
  Call Trace:
  [c000007fffbcfbe0] [c000000000039204] soft_nmi_interrupt+0xb4/0x5f0 (unreliable)
  [c000007fffbcfcf0] [c00000000000c0e8] soft_nmi_common+0x138/0x1c4
  --- interrupt: 900 at end_real_trampolines+0x0/0x1000
  NIP:  c000000000003000 LR: 00007ca426adb03c CTR: 900000000280f033
  REGS: c000007fffbcfd60 TRAP: 0900
  MSR:  9000000000009033 <SF,HV,EE,ME,IR,DR,RI,LE>  CR: 44042482  XER: 200400ad
  CFAR: 00007ca426946020 IRQMASK: 0
  GPR00: 00000000000000ad 00007ffffa45d050 00007ca426b07f00 0000000000000035
  GPR04: 00007ffffa45d078 0000000000000000 0000000000000008 0000000000000020
  GPR08: 0000000000000000 0000000000100000 0000000010000000 00007ffffa45d110
  GPR12: 0000000000000001 00007ca426d4e680 00000f7075bf4480 000000000000002a
  GPR16: 00000f705745a528 00007ffffa45ddd8 00000f70574d0008 0000000000000000
  GPR20: 00000f7075c58d70 00000f7057459c38 0000000000000001 0000000000000040
  GPR24: 0000000000000000 00000f7057473f68 0000000000000003 000000000000041b
  GPR28: 00007ffffa45d4c4 0000000000000035 0000000000000000 00000f7057473f68
  NIP [c000000000003000] end_real_trampolines+0x0/0x1000
  LR [00007ca426adb03c] 0x7ca426adb03c
  --- interrupt: 900
  Instruction dump:
  60000000 60000000 60420000 38600001 482b3ae5 60000000 e93f0138 a36d0008
  7daa6b78 71290001 7f7907b4 4082fd34 <0fe00000> 4bfffd2c 60420000 ea6100a8
  ---[ end trace dc75f67d819779da ]---

Fixes: 118178e62e2e ("powerpc: move NMI entry/exit code into wrapper")
Reported-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210503111708.758261-1-npiggin@gmail.com

powerpc/64s: Fix stf mitigation patching w/strict RWX & hash

The stf entry barrier fallback is unsafe to execute in a semi-patched
state, which can happen when enabling/disabling the mitigation with
strict kernel RWX enabled and using the hash MMU.

See the previous commit for more details.

Fix it by changing the order in which we patch the instructions.

Note the stf barrier fallback is only used on Power6 or earlier.

Fixes: bd573a81312f ("powerpc/mm/64s: Allow STRICT_KERNEL_RWX again")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210513140800.1391706-2-mpe@ellerman.id.au

powerpc/64s: Fix entry flush patching w/strict RWX & hash

The entry flush mitigation can be enabled/disabled at runtime. When this
happens it results in the kernel patching its own instructions to
enable/disable the mitigation sequence.

With strict kernel RWX enabled instruction patching happens via a
secondary mapping of the kernel text, so that we don't have to make the
primary mapping writable. With the hash MMU this leads to a hash fault,
which causes us to execute the exception entry which contains the entry
flush mitigation.

This means we end up executing the entry flush in a semi-patched state,
ie. after we have patched the first instruction but before we patch the
second or third instruction of the sequence.

On machines with updated firmware the entry flush is a series of special
nops, and it's safe to to execute in a semi-patched state.

However when using the fallback flush the sequence is mflr/branch/mtlr,
and so it's not safe to execute if we have patched out the mflr but not
the other two instructions. Doing so leads to us corrputing LR, leading
to an oops, for example:

  # echo 0 > /sys/kernel/debug/powerpc/entry_flush
  kernel tried to execute exec-protected page (c000000002971000) - exploit attempt? (uid: 0)
  BUG: Unable to handle kernel instruction fetch
  Faulting instruction address: 0xc000000002971000
  Oops: Kernel access of bad area, sig: 11 [#1]
  LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
  CPU: 0 PID: 2215 Comm: bash Not tainted 5.13.0-rc1-00010-gda3bb206c9ce #1
  NIP:  c000000002971000 LR: c000000002971000 CTR: c000000000120c40
  REGS: c000000013243840 TRAP: 0400   Not tainted  (5.13.0-rc1-00010-gda3bb206c9ce)
  MSR:  8000000010009033 <SF,EE,ME,IR,DR,RI,LE>  CR: 48428482  XER: 00000000
  ...
  NIP  0xc000000002971000
  LR   0xc000000002971000
  Call Trace:
    do_patch_instruction+0xc4/0x340 (unreliable)
    do_entry_flush_fixups+0x100/0x3b0
    entry_flush_set+0x50/0xe0
    simple_attr_write+0x160/0x1a0
    full_proxy_write+0x8c/0x110
    vfs_write+0xf0/0x340
    ksys_write+0x84/0x140
    system_call_exception+0x164/0x2d0
    system_call_common+0xec/0x278

The simplest fix is to change the order in which we patch the
instructions, so that the sequence is always safe to execute. For the
non-fallback flushes it doesn't matter what order we patch in.

Fixes: bd573a81312f ("powerpc/mm/64s: Allow STRICT_KERNEL_RWX again")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210513140800.1391706-1-mpe@ellerman.id.au

powerpc/64s: Fix crashes when toggling entry flush barrier

The entry flush mitigation can be enabled/disabled at runtime via a
debugfs file (entry_flush), which causes the kernel to patch itself to
enable/disable the relevant mitigations.

However depending on which mitigation we're using, it may not be safe to
do that patching while other CPUs are active. For example the following
crash:

sleeper[15639]: segfault (11) at c000000000004c20 nip c000000000004c20 lr c000000000004c20

Shows that we returned to userspace with a corrupted LR that points into
the kernel, due to executing the partially patched call to the fallback
entry flush (ie. we missed the LR restore).

Fix it by doing the patching under stop machine. The CPUs that aren't
doing the patching will be spinning in the core of the stop machine
logic. That is currently sufficient for our purposes, because none of
the patching we do is to that code or anywhere in the vicinity.

Fixes: f79643787e0a ("powerpc/64s: flush L1D on kernel entry")
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210506044959.1298123-2-mpe@ellerman.id.au

powerpc/64s: Fix crashes when toggling stf barrier

The STF (store-to-load forwarding) barrier mitigation can be
enabled/disabled at runtime via a debugfs file (stf_barrier), which
causes the kernel to patch itself to enable/disable the relevant
mitigations.

However depending on which mitigation we're using, it may not be safe to
do that patching while other CPUs are active. For example the following
crash:

  User access of kernel address (c00000003fff5af0) - exploit attempt? (uid: 0)
  segfault (11) at c00000003fff5af0 nip 7fff8ad12198 lr 7fff8ad121f8 code 1
  code: 40820128 e93c00d0 e9290058 7c292840 40810058 38600000 4bfd9a81 e8410018
  code: 2c030006 41810154 3860ffb6 e9210098 <e94d8ff0> 7d295279 39400000 40820a3c

Shows that we returned to userspace without restoring the user r13
value, due to executing the partially patched STF exit code.

Fix it by doing the patching under stop machine. The CPUs that aren't
doing the patching will be spinning in the core of the stop machine
logic. That is currently sufficient for our purposes, because none of
the patching we do is to that code or anywhere in the vicinity.

Fixes: a048a07d7f45 ("powerpc/64s: Add support for a store forwarding barrier at kernel entry/exit")
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210506044959.1298123-1-mpe@ellerman.id.au

Merge tag 'amd-drm-fixes-5.13-2021-05-13' of https://gitlab.freedesktop.org/agd5f/linux into drm-fixes

amd-drm-fixes-5.13-2021-05-13:

amdgpu:
- Fixes for flexible array conversions
- Fix sysfs attribute init
- Harvesting fixes
- VCN CG/PG fixes for Picasso

radeon:
- Fixes for flexible array conversions
- Fix for flickering on Oland with multiple 4K displays

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210513163228.3963-1-alexander.deucher@amd.com

Merge tag 'drm-misc-fixes-2021-05-13' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes

Remove an unused function and a MAINTAINERS update.

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210513133617.xq77wwrehpuh7yn2@hendrix

Merge tag 'pm-5.13-rc2' of git://git./linux/kernel/git/rafael/linux-pm

Pull power management fixes from Rafael Wysocki:
"These close a coverage gap in the intel_pstate driver and fix runtime
  PM child count imbalance related to interactions with system-wide
  suspend.

  Specifics:

   - Make intel_pstate work as expected on systems where the platform
     firmware enables HWP even though the HWP EPP support is not
     advertised (Rafael Wysocki).

   - Fix possible runtime PM child count imbalance that may occur if
     other runtime PM functions are called after invoking
     pm_runtime_force_suspend() and before pm_runtime_force_resume()
     is called (Tony Lindgren)"

* tag 'pm-5.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  PM: runtime: Fix unpaired parent child_count for force_resume
  cpufreq: intel_pstate: Use HWP if enabled by platform firmware

Merge tag 'acpi-5.13-rc2' of git://git./linux/kernel/git/rafael/linux-pm

Pull ACPI fixes from Rafael Wysocki:
"These revert an unnecessary revert of an ACPI power management commit,
  add a missing device ID to one of the lists and fix a possible memory
  leak in an error path.

  Specifics:

   - Revert a revert of a recent ACPI power management change that does
     not need to be reverted after all (Rafael Wysocki).

   - Add missing fan device ID to the list of device IDs for which the
     devices should not be put into the ACPI PM domain (Sumeet
     Pawnikar).

   - Fix possible memory leak in an error path in the ACPI device
     enumeration code (Christophe JAILLET)"

* tag 'acpi-5.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI: PM: Add ACPI ID of Alder Lake Fan
  ACPI: scan: Fix a memory leak in an error handling path
  Revert "Revert "ACPI: scan: Turn off unused power resources during initialization""

Merge branch 'acpi-pm'

* acpi-pm:
ACPI: PM: Add ACPI ID of Alder Lake Fan
Revert "Revert "ACPI: scan: Turn off unused power resources during initialization""

Merge branch 'pm-core'

* pm-core:
PM: runtime: Fix unpaired parent child_count for force_resume

tracing: Handle %.*s in trace_check_vprintf()

If a trace event uses the %*.s notation, the trace_check_vprintf() will
fail and will warn about a bad processing of strings, because it does not
take into account the length field when processing the star (*) part.
Have it handle this case as well.

Link: https://lore.kernel.org/linux-nfs/238C0E2D-C2A4-4578-ADD2-C565B3B99842@oracle.com/
Reported-by: Chuck Lever III <chuck.lever@oracle.com>
Fixes: 9a6944fee68e2 ("tracing: Add a verifier to check string pointers for trace events")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

Merge branch 'resizex' (patches from Maciej)

Merge VT_RESIZEX fixes from Maciej Rozycki:
"I got to the bottom of the issue with VT_RESIZEX recently discussed
  and came up with this small patch series, fixing an additional issue
  that I originally thought might be broken VGA hardware emulation with
  my laptop, which however turned out to be intertwined with the
  original problem and also a regression introduced somewhat later.

  The fix for that because the first patch, and then to make backporting
  feasible I had to put a revert of the offending change from last
  September next, followed by a proper fix for the framebuffer issue
  that change had tried to address.

  See individual change descriptions for details.

  These have been verified with true VGA hardware (a Trident TVGA8900
  ISA video adapter) using various combinations of `svgatextmode' and
  `setfont' command invocations to change both the VT size and the font
  size, and also switching between the text console and X11, both by
  starting/stopping the X server and by switching between VTs.

  All this to ensure bringing the behaviour of VGA text console back to
  correct operation as it used to be with Linux 2.6.18"

* emailed patches from Maciej W. Rozycki <macro@orcam.me.uk>:
  vt: Fix character height handling with VT_RESIZEX
  vt_ioctl: Revert VT_RESIZEX parameter handling removal
  vgacon: Record video mode changes with VT_RESIZEX

vt: Fix character height handling with VT_RESIZEX

Restore the original intent of the VT_RESIZEX ioctl's `v_clin' parameter
which is the number of pixel rows per character (cell) rather than the
height of the font used.

For framebuffer devices the two values are always the same, because the
former is inferred from the latter one.  For VGA used as a true text
mode device these two parameters are independent from each other: the
number of pixel rows per character is set in the CRT controller, while
font height is in fact hardwired to 32 pixel rows and fonts of heights
below that value are handled by padding their data with blanks when
loaded to hardware for use by the character generator.  One can change
the setting in the CRT controller and it will update the screen contents
accordingly regardless of the font loaded.

The `v_clin' parameter is used by the `vgacon' driver to set the height
of the character cell and then the cursor position within.  Make the
parameter explicit then, by defining a new `vc_cell_height' struct
member of `vc_data', set it instead of `vc_font.height' from `v_clin' in
the VT_RESIZEX ioctl, and then use it throughout the `vgacon' driver
except where actual font data is accessed which as noted above is
independent from the CRTC setting.

This way the framebuffer console driver is free to ignore the `v_clin'
parameter as irrelevant, as it always should have, avoiding any issues
attempts to give the parameter a meaning there could have caused, such
as one that has led to commit 988d0763361b ("vt_ioctl: make VT_RESIZEX
behave like VT_RESIZE"):

"syzbot is reporting UAF/OOB read at bit_putcs()/soft_cursor() [1][2],
  for vt_resizex() from ioctl(VT_RESIZEX) allows setting font height
  larger than actual font height calculated by con_font_set() from
  ioctl(PIO_FONT). Since fbcon_set_font() from con_font_set() allocates
  minimal amount of memory based on actual font height calculated by
  con_font_set(), use of vt_resizex() can cause UAF/OOB read for font
  data."

The problem first appeared around Linux 2.5.66 which predates our repo
history, but the origin could be identified with the old MIPS/Linux repo
also at: <git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux.git>
as commit 9736a3546de7 ("Merge with Linux 2.5.66."), where VT_RESIZEX
code in `vt_ioctl' was updated as follows:

if (clin)
- video_font_height = clin;
+ vc->vc_font.height = clin;

making the parameter apply to framebuffer devices as well, perhaps due
to the use of "font" in the name of the original `video_font_height'
variable.  Use "cell" in the new struct member then to avoid ambiguity.

References:

[1] https://syzkaller.appspot.com/bug?id=32577e96d88447ded2d3b76d71254fb855245837
[2] https://syzkaller.appspot.com/bug?id=6b8355d27b2b94fb5cedf4655e3a59162d9e48e3

Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org # v2.6.12+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

vt_ioctl: Revert VT_RESIZEX parameter handling removal

Revert the removal of code handling extra VT_RESIZEX ioctl's parameters
beyond those that VT_RESIZE supports, fixing a functional regression
causing `svgatextmode' not to resize the VT anymore.

As a consequence of the reverted change when the video adapter is
reprogrammed from the original say 80x25 text mode using a 9x16
character cell (720x400 pixel resolution) to say 80x37 text mode and the
same character cell (720x592 pixel resolution), the VT geometry does not
get updated and only upper two thirds of the screen are used for the VT,
and the lower part remains blank. The proportions change according to
text mode geometries chosen.

Revert the change verbatim then, bringing back previous VT resizing.

Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 988d0763361b ("vt_ioctl: make VT_RESIZEX behave like VT_RESIZE")
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

vgacon: Record video mode changes with VT_RESIZEX

Fix an issue with VGA console font size changes made after the initial
video text mode has been changed with a user tool like `svgatextmode'
calling the VT_RESIZEX ioctl. As it stands in that case the original
screen geometry continues being used to validate further VT resizing.

Consequently when the video adapter is firstly reprogrammed from the
original say 80x25 text mode using a 9x16 character cell (720x400 pixel
resolution) to say 80x37 text mode and the same character cell (720x592
pixel resolution), and secondly the CRTC character cell updated to 9x8
(by loading a suitable font with the KD_FONT_OP_SET request of the
KDFONTOP ioctl), the VT geometry does not get further updated from 80x37
and only upper half of the screen is used for the VT, with the lower
half showing rubbish corresponding to whatever happens to be there in
the video memory that maps to that part of the screen. Of course the
proportions change according to text mode geometries and font sizes
chosen.

Address the problem then, by updating the text mode geometry defaults
rather than checking against them whenever the VT is resized via a user
ioctl.

Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: e400b6ec4ede ("vt/vgacon: Check if screen resize request comes from userspace")
Cc: stable@vger.kernel.org # v2.6.24+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'nvme-5.13-2021-05-13' of git://git.infradead.org/nvme into block-5.13

Pull NVMe fixes from Christoph:

"nvme fix for Linux 5.13

- correct the check for using the inline bio in nvmet
   (Chaitanya Kulkarni)
- demote unsupported command warnings (Chaitanya Kulkarni)
- fix corruption due to double initializing ANA state (me, Hou Pu)
- reset ns->file when open fails (Daniel Wagner)
- fix a NULL deref when SEND is completed with error in nvmet-rdma
   (Michal Kalderon)"

* tag 'nvme-5.13-2021-05-13' of git://git.infradead.org/nvme:
  nvmet: use new ana_log_size instead the old one
  nvmet: seset ns->file when open fails
  nvmet: demote fabrics cmd parse err msg to debug
  nvmet: use helper to remove the duplicate code
  nvmet: demote discovery cmd parse err msg to debug
  nvmet-rdma: Fix NULL deref when SEND is completed with error
  nvmet: fix inline bio check for passthru
  nvmet: fix inline bio check for bdev-ns
  nvme-multipath: fix double initialization of ANA state

Merge tag 'hwmon-for-v5.13-rc2' of git://git./linux/kernel/git/groeck/linux-staging

Pull hwmon fixes from Guenter Roeck:
"Fix bugs/regressions in adm9240, ltc2992, pmbus/fsp-3y, and occ
  drivers, plus a minor cleanup in the corsair-psu driver"

* tag 'hwmon-for-v5.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (adm9240) Fix writes into inX_max attributes
  hwmon: (ltc2992) Put fwnode in error case during ->probe()
  hwmon: (pmbus/fsp-3y) Fix FSP-3Y YH-5151E non-compliant vout encoding
  hwmon: (occ) Fix poll rate limiting
  hwmon: (corsair-psu) Remove unneeded semicolons

arm64: tools: Add __ASM_CPUCAPS_H to the endif in cpucaps.h

Anshuman suggested this.

Suggested-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210513151819.12526-1-broonie@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

drm/amdgpu: update vcn1.0 Non-DPG suspend sequence

update suspend register settings in Non-DPG mode.

Signed-off-by: Sathishkumar S <sathishkumar.sundararaju@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: set vcn mgcg flag for picasso

enable vcn mgcg flag for picasso.

Signed-off-by: Sathishkumar S <sathishkumar.sundararaju@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/dpm: Disable sclk switching on Oland when two 4K 60Hz monitors are connected

Screen flickers rapidly when two 4K 60Hz monitors are in use. This issue
doesn't happen when one monitor is 4K 60Hz (pixelclock 594MHz) and
another one is 4K 30Hz (pixelclock 297MHz).

The issue is gone after setting "power_dpm_force_performance_level" to
"high". Following the indication, we found that the issue occurs when
sclk is too low.

So resolve the issue by disabling sclk switching when there are two
monitors requires high pixelclock (> 297MHz).

v2:
- Only apply the fix to Oland.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

drm/amdgpu: update the method for harvest IP for specific SKU

Update the method of disabling VCN IP for specific SKU for navi1x ASIC,
it will judge whether should add the related IP at the function of
amdgpu_device_ip_block_add().

Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add judgement when add ip blocks (v2)

Judgement whether to add an sw ip according to the harvest info.

v2: fix indentation (Alex)

Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Initialize attribute for hdcp_srm sysfs file

It is stored in dynamically allocated memory, so sysfs_bin_attr_init() must
be called to initialize it. (Note: "initialization" only sets the .attr.key
member in this struct; it does not change the value of any other members.)

Otherwise, when CONFIG_DEBUG_LOCK_ALLOC=y this message appears during boot:

BUG: key ffff9248900cd148 has not been registered!

Fixes: 9037246bb2da ("drm/amd/display: Add sysfs interface for set/get srm")
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1586
Reported-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Signed-off-by: David Ward <david.ward@gatech.edu>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

drm/amd/pm: Fix out-of-bounds bug

Create new structure SISLANDS_SMC_SWSTATE_SINGLE, as initialState.levels
and ACPIState.levels are never actually used as flexible arrays. Those
arrays can be used as simple objects of type
SISLANDS_SMC_HW_PERFORMANCE_LEVEL, instead.

Currently, the code fails because flexible array _levels_ in
struct SISLANDS_SMC_SWSTATE doesn't allow for code that accesses
the first element of initialState.levels and ACPIState.levels
arrays:

drivers/gpu/drm/amd/pm/powerplay/si_dpm.c:
4820: table->initialState.levels[0].mclk.vDLL_CNTL =
4821: cpu_to_be32(si_pi->clock_registers.dll_cntl);
...
5021: table->ACPIState.levels[0].mclk.vDLL_CNTL =
5022: cpu_to_be32(dll_cntl);

because such element cannot be accessed without previously allocating
enough dynamic memory for it to exist (which never actually happens).
So, there is an out-of-bounds bug in this case.

That's why struct SISLANDS_SMC_SWSTATE should only be used as type
for object driverState and new struct SISLANDS_SMC_SWSTATE_SINGLE is
created as type for objects initialState, ACPIState and ULVState.

Also, with the change from one-element array to flexible-array member
in commit 0e1aa13ca3ff ("drm/amd/pm: Replace one-element array with
flexible-array in struct SISLANDS_SMC_SWSTATE"), the size of
dpmLevels in struct SISLANDS_SMC_STATETABLE should be fixed to be
SISLANDS_MAX_SMC_PERFORMANCE_LEVELS_PER_SWSTATE instead of
SISLANDS_MAX_SMC_PERFORMANCE_LEVELS_PER_SWSTATE - 1.

Fixes: 0e1aa13ca3ff ("drm/amd/pm: Replace one-element array with flexible-array in struct SISLANDS_SMC_SWSTATE")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/si_dpm: Fix SMU power state load

Create new structure SISLANDS_SMC_SWSTATE_SINGLE, as initialState.levels
and ACPIState.levels are never actually used as flexible arrays. Those
arrays can be used as simple objects of type
SISLANDS_SMC_HW_PERFORMANCE_LEVEL, instead.

Currently, the code fails because flexible array _levels_ in
struct SISLANDS_SMC_SWSTATE doesn't allow for code that access
the first element of initialState.levels and ACPIState.levels
arrays:

4353         table->initialState.levels[0].mclk.vDLL_CNTL =
4354                 cpu_to_be32(si_pi->clock_registers.dll_cntl);
...
4555         table->ACPIState.levels[0].mclk.vDLL_CNTL =
4556                 cpu_to_be32(dll_cntl);

because such element cannot exist without previously allocating
any dynamic memory for it (which never actually happens).

That's why struct SISLANDS_SMC_SWSTATE should only be used as type
for object driverState and new struct SISLANDS_SMC_SWSTATE_SINGLE is
created as type for objects initialState, ACPIState and ULVState.

Also, with the change from one-element array to flexible-array member
in commit 96e27e8d919e ("drm/radeon/si_dpm: Replace one-element array
with flexible-array in struct SISLANDS_SMC_SWSTATE"), the size of
dpmLevels in struct SISLANDS_SMC_STATETABLE should be fixed to be
SISLANDS_MAX_SMC_PERFORMANCE_LEVELS_PER_SWSTATE instead of
SISLANDS_MAX_SMC_PERFORMANCE_LEVELS_PER_SWSTATE - 1.

Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1583
Fixes: 96e27e8d919e ("drm/radeon/si_dpm: Replace one-element array with flexible-array in struct SISLANDS_SMC_SWSTATE")
Cc: stable@vger.kernel.org
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/ni_dpm: Fix booting bug

Create new structure NISLANDS_SMC_SWSTATE_SINGLE, as initialState.levels
and ACPIState.levels are never actually used as flexible arrays. Those
arrays can be used as simple objects of type
NISLANDS_SMC_HW_PERFORMANCE_LEVEL, instead.

Currently, the code fails because flexible array _levels_ in
struct NISLANDS_SMC_SWSTATE doesn't allow for code that access
the first element of initialState.levels and ACPIState.levels
arrays:

drivers/gpu/drm/radeon/ni_dpm.c:
1690         table->initialState.levels[0].mclk.vMPLL_AD_FUNC_CNTL =
1691                 cpu_to_be32(ni_pi->clock_registers.mpll_ad_func_cntl);
...
1903:   table->ACPIState.levels[0].mclk.vMPLL_AD_FUNC_CNTL = cpu_to_be32(mpll_ad_func_cntl);
1904:   table->ACPIState.levels[0].mclk.vMPLL_AD_FUNC_CNTL_2 = cpu_to_be32(mpll_ad_func_cntl_2);

because such element cannot exist without previously allocating
any dynamic memory for it (which never actually happens).

That's why struct NISLANDS_SMC_SWSTATE should only be used as type
for object driverState and new struct SISLANDS_SMC_SWSTATE_SINGLE is
created as type for objects initialState, ACPIState and ULVState.

Also, with the change from one-element array to flexible-array member
in commit 434fb1e7444a ("drm/radeon/nislands_smc.h: Replace one-element
array with flexible-array member in struct NISLANDS_SMC_SWSTATE"), the
size of dpmLevels in struct NISLANDS_SMC_STATETABLE should be fixed to
be NISLANDS_MAX_SMC_PERFORMANCE_LEVELS_PER_SWSTATE instead of
NISLANDS_MAX_SMC_PERFORMANCE_LEVELS_PER_SWSTATE - 1.

Bug: https://lore.kernel.org/dri-devel/3eedbe78-1fbd-4763-a7f3-ac5665e76a4a@xenosoft.de/
Fixes: 434fb1e7444a ("drm/radeon/nislands_smc.h: Replace one-element array with flexible-array member in struct NISLANDS_SMC_SWSTATE")
Cc: stable@vger.kernel.org
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Link: https://lore.kernel.org/dri-devel/9bb5fcbd-daf5-1669-b3e7-b8624b3c36f9@xenosoft.de/
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

nvmet: use new ana_log_size instead the old one

The new ana_log_size should be used instead of the old one.
Or kernel NULL pointer dereference will happen like below:

[   38.957849][   T69] BUG: kernel NULL pointer dereference, address: 000000000000003c
[   38.975550][   T69] #PF: supervisor write access in kernel mode
[   38.975955][   T69] #PF: error_code(0x0002) - not-present page
[   38.976905][   T69] PGD 0 P4D 0
[   38.979388][   T69] Oops: 0002 [#1] SMP NOPTI
[   38.980488][   T69] CPU: 0 PID: 69 Comm: kworker/0:2 Not tainted 5.12.0+ #54
[   38.981254][   T69] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014
[   38.982502][   T69] Workqueue: events nvme_loop_execute_work
[   38.985219][   T69] RIP: 0010:memcpy_orig+0x68/0x10f
[   38.986203][   T69] Code: 83 c2 20 eb 44 48 01 d6 48 01 d7 48 83 ea 20 0f 1f 00 48 83 ea 20 4c 8b 46 f8 4c 8b 4e f0 4c 8b 56 e8 4c 8b 5e e0 48 8d 76 e0 <4c> 89 47 f8 4c 89 4f f0 4c 89 57 e8 4c 89 5f e0 48 8d 7f e0 73 d2
[   38.987677][   T69] RSP: 0018:ffffc900001b7d48 EFLAGS: 00000287
[   38.987996][   T69] RAX: 0000000000000020 RBX: 0000000000000024 RCX: 0000000000000010
[   38.988327][   T69] RDX: ffffffffffffffe4 RSI: ffff8881084bc004 RDI: 0000000000000044
[   38.988620][   T69] RBP: 0000000000000024 R08: 0000000100000000 R09: 0000000000000000
[   38.988991][   T69] R10: 0000000100000000 R11: 0000000000000001 R12: 0000000000000024
[   38.989289][   T69] R13: ffff8881084bc000 R14: 0000000000000000 R15: 0000000000000024
[   38.989845][   T69] FS:  0000000000000000(0000) GS:ffff888237c00000(0000) knlGS:0000000000000000
[   38.990234][   T69] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   38.990490][   T69] CR2: 000000000000003c CR3: 00000001085b2000 CR4: 00000000000006f0
[   38.991105][   T69] Call Trace:
[   38.994157][   T69]  sg_copy_buffer+0xb8/0xf0
[   38.995357][   T69]  nvmet_copy_to_sgl+0x48/0x6d
[   38.995565][   T69]  nvmet_execute_get_log_page_ana+0xd4/0x1cb
[   38.995792][   T69]  nvmet_execute_get_log_page+0xc9/0x146
[   38.995992][   T69]  nvme_loop_execute_work+0x3e/0x44
[   38.996181][   T69]  process_one_work+0x1c3/0x3c0
[   38.996393][   T69]  worker_thread+0x44/0x3d0
[   38.996600][   T69]  ? cancel_delayed_work+0x90/0x90
[   38.996804][   T69]  kthread+0xf7/0x130
[   38.996961][   T69]  ? kthread_create_worker_on_cpu+0x70/0x70
[   38.997171][   T69]  ret_from_fork+0x22/0x30
[   38.997705][   T69] Modules linked in:
[   38.998741][   T69] CR2: 000000000000003c
[   39.000104][   T69] ---[ end trace e719927b609d0fa0 ]---

Fixes: 5e1f689913a4 ("nvme-multipath: fix double initialization of ANA state")
Signed-off-by: Hou Pu <houpu.main@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

usb: core: hub: fix race condition about TRSMRCY of resume

This may happen if the port becomes resume status exactly
when usb_port_resume() gets port status, it still need provide
a TRSMCRY time before access the device.

CC: <stable@vger.kernel.org>
Reported-by: Tianping Fang <tianping.fang@mediatek.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20210512020738.52961-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: typec: tcpm: Fix SINK_DISCOVERY current limit for Rp-default

This is a regression introduced by 1373fefc6243 ("usb: typec: tcpm:
Allow slow charging loops to comply to pSnkStby")

When Source advertises Rp-default, tcpm would request 500mA when in
SINK_DISCOVERY, Type-C spec advises the sink to follow BC1.2 current
limits when Rp-default is advertised.
[12750.503381] Requesting mux state 1, usb-role 2, orientation 1
[12750.503837] state change SNK_ATTACHED -> SNK_STARTUP [rev3 NONE_AMS]
[12751.003891] state change SNK_STARTUP -> SNK_DISCOVERY
[12751.003900] Setting voltage/current limit 5000 mV 500 mA

This patch restores the behavior where the tcpm would request 0mA when
Rp-default is advertised by the source.
[   73.174252] Requesting mux state 1, usb-role 2, orientation 1
[   73.174749] state change SNK_ATTACHED -> SNK_STARTUP [rev3 NONE_AMS]
[   73.674800] state change SNK_STARTUP -> SNK_DISCOVERY
[   73.674808] Setting voltage/current limit 5000 mV 0 mA

During SNK_DISCOVERY, Cap the current limit to PD_P_SNK_STDBY_MW / 5 only
for slow_charger_loop case.

Fixes: 1373fefc6243 ("usb: typec: tcpm: Allow slow charging loops to comply to pSnkStby")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210510211756.3346954-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xhci: Add reset resume quirk for AMD xhci controller.

One of AMD xhci controller require reset on resume.
Occasionally AMD xhci controller does not respond to
Stop endpoint command.
Once the issue happens controller goes into bad state
and in that case controller needs to be reset.

Cc: <stable@vger.kernel.org>
Signed-off-by: Sandeep Singh <sandeep.singh@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210512080816.866037-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: xhci: Increase timeout for HC halt

On some devices (specifically the SC8180x based Surface Pro X with
QCOM04A6) HC halt / xhci_halt() times out during boot. Manually binding
the xhci-hcd driver at some point later does not exhibit this behavior.
To work around this, double XHCI_MAX_HALT_USEC, which also resolves this
issue.

Cc: <stable@vger.kernel.org>
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210512080816.866037-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xhci: Do not use GFP_KERNEL in (potentially) atomic context

'xhci_urb_enqueue()' is passed a 'mem_flags' argument, because "URBs may be
submitted in interrupt context" (see comment related to 'usb_submit_urb()'
in 'drivers/usb/core/urb.c')

So this flag should be used in all the calling chain.
Up to now, 'xhci_check_maxpacket()' which is only called from
'xhci_urb_enqueue()', uses GFP_KERNEL.

Be safe and pass the mem_flags to this function as well.

Fixes: ddba5cd0aeff ("xhci: Use command structures when queuing commands on the command ring")
Cc: <stable@vger.kernel.org>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210512080816.866037-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xhci: Fix giving back cancelled URBs even if halted endpoint can't reset

Commit 9ebf30007858 ("xhci: Fix halted endpoint at stop endpoint command
completion") in 5.12 changes how cancelled URBs are given back.

To cancel a URB xhci driver needs to stop the endpoint first.
To clear a halted endpoint xhci driver needs to reset the endpoint.

In rare cases when an endpoint halt (error) races with a endpoint stop we
need to clear the reset before removing, and giving back the cancelled URB.

The above change in 5.12 takes care of this, but it also relies on the
reset endpoint completion handler to give back the cancelled URBs.

There are cases when driver refuses to queue reset endpoint commands,
for example when a link suddenly goes to an inactive error state.
In this case the cancelled URB is never given back.

Fix this by giving back the URB in the stop endpoint if queuing a reset
endpoint command fails.

Fixes: 9ebf30007858 ("xhci: Fix halted endpoint at stop endpoint command completion")
CC: <stable@vger.kernel.org> # 5.12
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210512080816.866037-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xhci-pci: Allow host runtime PM as default for Intel Alder Lake xHCI

In the same way as Intel Tiger Lake TCSS (Type-C Subsystem) the Alder Lake
TCSS xHCI needs to be runtime suspended whenever possible to allow the
TCSS hardware block to enter D3cold and thus save energy.

Cc: stable@vger.kernel.org
Signed-off-by: Abhijeet Rao <abhijeet.rao@intel.com>
Signed-off-by: Nikunj A. Dadhania <nikunj.dadhania@intel.com>
Signed-off-by: Azhar Shaikh <azhar.shaikh@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210512080816.866037-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86, sched: Fix the AMD CPPC maximum performance value on certain AMD Ryzen generations

Some AMD Ryzen generations has different calculation method on maximum
performance. 255 is not for all ASICs, some specific generations should use 166
as the maximum performance. Otherwise, it will report incorrect frequency value
like below:

  ~ → lscpu | grep MHz
  CPU MHz:                         3400.000
  CPU max MHz:                     7228.3198
  CPU min MHz:                     2200.0000

[ mingo: Tidied up whitespace use. ]
[ Alexander Monakov <amonakov@ispras.ru>: fix 225 -> 255 typo. ]

Fixes: 41ea667227ba ("x86, sched: Calculate frequency invariance for AMD systems")
Fixes: 3c55e94c0ade ("cpufreq: ACPI: Extend frequency tables to cover boost frequencies")
Reported-by: Jason Bagavatsingham <jason.bagavatsingham@gmail.com>
Fixed-by: Alexander Monakov <amonakov@ispras.ru>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Jason Bagavatsingham <jason.bagavatsingham@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210425073451.2557394-1-ray.huang@amd.com
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=211791
Signed-off-by: Ingo Molnar <mingo@kernel.org>