Jean-Christophe PLAGNIOL-VILLARD [Thu, 18 Oct 2007 22:09:05 +0000 (00:09 +0200)]
Fix missing drivers makefile entries ds1722.c mw_eeprom.c
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Thu, 18 Oct 2007 22:07:39 +0000 (00:07 +0200)]
Fix warning differ in signedness in board/innokom/innokom.c
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Marcel Ziswiler [Thu, 18 Oct 2007 22:25:33 +0000 (00:25 +0200)]
fix pxa255_idp board
The pxa255_idp being an old unmaintained board showed several issues:
1. CONFIG_INIT_CRITICAL was still defined.
2. Neither CONFIG_MAC_PARTITION nor CONFIG_DOS_PARTITION was defined.
3. Symbol flash_addr was undeclared.
4. The boards lowlevel_init function was still called memsetup.
5. The TEXT_BASE was still 0xa3000000 rather than 0xa3080000.
6. Using -march=armv5 instead of -march=armv5te resulted in lots of
'target CPU does not support interworking' warnings on recent compilers.
7. The PXA's serial driver redefined FFUART, BTUART and STUART used as
indexes rather than the register definitions from the pxa-regs header
file. Renamed them to FFUART_INDEX, BTUART_INDEX and STUART_INDEX to
avoid any ambiguities.
8. There were several redefinition warnings concerning ICMR, OSMR3,
OSCR, OWER, OIER, RCSR and CCCR in the PXA's assembly start file.
9. The board configuration file was rather outdated.
10. The part header file defined the vendor, product and revision arrays
as unsigned chars instead of just chars in the block_dev_desc_t
structure.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Rune Torgersen [Wed, 17 Oct 2007 16:56:31 +0000 (11:56 -0500)]
Make MPC8266ADS command selection more robust
Fix MPC8266 command line definition so it won't break when new commands
are added to u-boot.
Signed-off-by Rune Torgersen <runet@innovsys.com>
Bartlomiej Sieka [Tue, 23 Oct 2007 11:14:10 +0000 (13:14 +0200)]
Motion-PRO: Update configuration to accomodate next generation board.
New board has faster oscillator and a different Flash chip. This affects:
- CFG_MPC5XXX_CLKIN
- SDRAM timings
- Flash CS configuration (timings)
- Flash sector size, and thus MTD partition layout
- malloc() arena size (due to bigger Flash sectors)
- smaller memory test range (due to bigger malloc() arena)
This patch also enables more extensive memory testing via "mtest".
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
Bartlomiej Sieka [Tue, 23 Oct 2007 09:36:07 +0000 (11:36 +0200)]
Motion-PRO: Add setting of SDelay reg. to SDRAM controller configuration.
Per AN3221 (MPC5200B SDRAM Initialization and Configuration), the SDelay
register must be written a value of 0x00000004 as the first step of the
SDRAM contorller configuration.
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
Peter Pearse [Tue, 23 Oct 2007 09:22:16 +0000 (10:22 +0100)]
Move PL01* serial drivers to drivers/serial and adjust Makefiles.
Stefan Roese [Tue, 23 Oct 2007 08:17:42 +0000 (10:17 +0200)]
ppc4xx: lwmon5: Some further GPIO config changes
Signed-off-by: Stefan Roese <sr@denx.de>
Martin Krause [Tue, 23 Oct 2007 06:30:06 +0000 (08:30 +0200)]
Merge branch 'u-boot' of /home/mkr/git/u-boot-tq-group into bugfix
Vlad Lungu [Sun, 21 Oct 2007 13:10:10 +0000 (22:10 +0900)]
[MIPS] Fix UNCACHED_SDRAM
PHYSADDR is for physical address, KSEG1ADDR is for uncached.
Signed-off-by: Vlad Lungu <vlad@comsys.ro>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Shinya Kuribayashi [Sun, 21 Oct 2007 12:30:42 +0000 (21:30 +0900)]
[MIPS] Add PIC-related switches to PLATFORM_{CPP,LD}FLAGS and cleanup
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Shinya Kuribayashi [Sun, 21 Oct 2007 01:55:37 +0000 (10:55 +0900)]
[MIPS] u-boot.lds: Define _gp in a standard manner
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Shinya Kuribayashi [Sun, 21 Oct 2007 01:55:36 +0000 (10:55 +0900)]
[MIPS] Fix $gp usage
Now we load $gp with _GLOBAL_OFFSET_TABLE_, but this is incorrect use.
As a general principle, we should use _gp for $gp.
Thanks to linker script's help we fortunately have _gp which equals to
_GLOBAL_OFFSET_TABLE_. But once _gp gets out of alignment, we will not
be able to access to GOT entires, global variables and procedure entry
points. The right thing to do is to use _gp.
This patch also introduce a new symbol `.gpword _GLOBAL_OFFSET_TABLE_'
which holds the offset from _gp. When updating GOT entries, we use this
offset and _gp to calculate the final _GLOBAL_OFFSET_TABLE_.
This patch is originally submitted by Vlad Lungu <vlad@comsys.ro>, then
I made some change to leave over num_got_entries.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Cc: Vlad Lungu <vlad@comsys.ro>
Shinya Kuribayashi [Sun, 21 Oct 2007 01:55:36 +0000 (10:55 +0900)]
[MIPS] u-boot.lds: Fix __got_start and __got_end
Ensure that __got_start points to top of the `.got', and __got_end points
to bottom as well, so that we never fail to count num_got_entries.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Shinya Kuribayashi [Sun, 21 Oct 2007 01:55:36 +0000 (10:55 +0900)]
[MIPS] u-boot.lds: Remove duplicated .sdata section
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Wolfgang Denk [Sat, 20 Oct 2007 23:01:17 +0000 (01:01 +0200)]
Minor coding style cleanup; update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
Vlad Lungu [Thu, 4 Oct 2007 17:47:10 +0000 (20:47 +0300)]
Fix NE2000 driver:
Fixed typo in ne2000.h, thinko re n2k_inb() usage, don't try
to do anything in eth_stop() if eth_init() was not called.
Simplified RX path in order to avoid timeouts on really really
fast NE2000 cards (read: qemu with internal tftp), NetLoop() is
clever enough to cope with 1 packet per eth_rx().
Signed-off-by: Vlad Lungu <vlad@comsys.ro>
Wolfgang Denk [Sat, 20 Oct 2007 22:29:32 +0000 (00:29 +0200)]
Merge branch 'master' of git://denx.de/git/u-boot-tq-group
Wolfgang Denk [Sat, 20 Oct 2007 22:10:34 +0000 (00:10 +0200)]
Merge branch 'master' of /home/git/u-boot/
urwithsughosh@gmail.com [Mon, 24 Sep 2007 17:32:13 +0000 (13:32 -0400)]
Setting MSR[DE] in do_reset
Hello,
This patch ensures the soft reset of the board for the 85xx boards
by setting the MSR[DE] in the do_reset function.
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
urwithsughosh@gmail.com [Mon, 24 Sep 2007 17:36:01 +0000 (13:36 -0400)]
MSR overwrite fix
Hello,
This patch fixes the MSR overwrite in the start.S when moving out of
the last 4K page.
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Dan Wilson [Fri, 19 Oct 2007 16:33:48 +0000 (11:33 -0500)]
tsec driver should clear RHALT on startup
This was causing problems for some people.
Signed-off-by: Alain Gravel <agravel@fulcrummicro.com>
Signed-off-by: Dan Wilson <dwilson@fulcrummicro.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Kumar Gala [Thu, 11 Oct 2007 05:29:18 +0000 (00:29 -0500)]
Improve handling of PCI interrupt device tree fixup on MPC85xx CDS
On the MPC85xx CDS we have two issues:
1. The device tree fixup code did not check to see if the property we are
trying to update is actually found. Its possible that it would update
random memory starting at 0.
2. Newer Linux kernel's have moved the location of the PCI nodes to be
sibilings of the soc node and not children. The explicit PATH to the PCI
node would not be found for these device trees. Add the ability to handle
both paths. In the future we shouldn't handle such fixups by explicit path.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 11 Oct 2007 05:18:48 +0000 (00:18 -0500)]
Set OF_STDOUT_PATH to match the default console on MPC8568 MDS
On the MPC8568 MDS we use ttyS0, UART0, etc. as the standard configured
console. Make it so we match that config what we tell Linux as the early
STDOUT console.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Tue, 2 Oct 2007 16:12:27 +0000 (11:12 -0500)]
Remove magic numbers from cache related operations for mpc85xx
The mpc85xx start code uses some magic numbers that we actually
have #defines for in <config.h> so use those instead.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Andy Fleming [Fri, 19 Oct 2007 16:24:22 +0000 (11:24 -0500)]
Merge branch 'denx'
Detlev Zundel [Fri, 19 Oct 2007 14:47:26 +0000 (16:47 +0200)]
Fix two typos.
Signed-off-by: Detlev Zundel <dzu@denx.de>
Wolfgang Denk [Thu, 18 Oct 2007 20:02:35 +0000 (22:02 +0200)]
Merge branch 'master' of git://denx.de/git/u-boot-ppc4xx
Tony Li [Thu, 18 Oct 2007 09:47:19 +0000 (17:47 +0800)]
mpc83xx: Add configure entry for MPC83xx ATM support
Add MPC8360EMDS_ATM_config and MPC832XEMDS_ATM_config into
Makfile and MAKEALL
Signed-off-by: Tony Li <tony.li@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Tony Li [Thu, 18 Oct 2007 09:44:38 +0000 (17:44 +0800)]
mpc83xx: pq-mds-pib.c typo error
Correct to val8 from val.
Signed-off-by: Tony Li <tony.li@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Kim Phillips [Thu, 18 Oct 2007 15:02:16 +0000 (10:02 -0500)]
Merge git://www.denx.de/git/u-boot
Stefan Roese [Wed, 17 Oct 2007 13:40:19 +0000 (15:40 +0200)]
ppc4xx: Add 667/133 (CPU/PLB) frequency setup to Sequoia bootstrap command
Signed-off-by: Stefan Roese <sr@denx.de>
runet@innovsys.com [Tue, 16 Oct 2007 19:50:40 +0000 (14:50 -0500)]
Make MPC8266ADS board compile again.
Signed-off-by: Runet Torgersen <runet@innovsys.com>
Wolfgang Denk [Tue, 16 Oct 2007 14:45:20 +0000 (16:45 +0200)]
Merge branch 'master' of git+ssh://gemini_vpn/home/wd/git/u-boot/master
Jon Loeliger [Mon, 27 Aug 2007 17:41:03 +0000 (12:41 -0500)]
86xx: Allow for fewer DDR slots per memory controller.
As a direct correlation exists between DDR DIMM slots
and SPD EEPROM addresses used to configure them, use
the individually defined SPD_EEPROM_ADDRESS* values to
determine if a DDR DIMM slot should have its SPD
configuration read or not.
Effectively, this now allows for 1 or 2 DIMM slots
per memory controller.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Wolfgang Denk [Mon, 15 Oct 2007 18:56:12 +0000 (20:56 +0200)]
Merge branch 'master' of /home/wd/git/u-boot/custodians
Wolfgang Denk [Mon, 15 Oct 2007 18:55:51 +0000 (20:55 +0200)]
Merge branch 'master' of git://denx.de/git/u-boot-usb
Wolfgang Denk [Mon, 15 Oct 2007 10:59:05 +0000 (12:59 +0200)]
Merge branch 'master' of git+ssh://gemini_vpn/home/wd/git/u-boot/master
Rodolfo Giometti [Mon, 15 Oct 2007 09:59:17 +0000 (11:59 +0200)]
PXA USB OHCI: "usb stop" implementation.
Some USB keys need to be switched off before loading the kernel
otherwise they can remain in an undefined status which prevents them
to be correctly recognized by the kernel.
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Stefan Roese [Mon, 15 Oct 2007 09:39:00 +0000 (11:39 +0200)]
ppc4xx: Fix bug in I2C bootstrap values for Sequoia/Rainier
The I2C bootstrap values that can be setup via the "bootstrap" command,
were setup incorrect regarding the generation of the internal sync PCI
clock. The values for PLB clock == 133MHz were slighly incorrect and the
values for PLB clock == 166MHz were totally incorrect. This could
lead to a hangup upon booting while PCI configuration scan.
This patch fixes this issue and configures valid PCI divisor values
for the sync PCI clock, with respect to the provided external async
PCI frequency.
Here the values of the formula in the chapter 14.2 "PCI clocking"
from the 440EPx users manual:
AsyncPCICLK - 1MHz <= SyncPCIClk <= (2 * AsyncPCIClk) - 1MHz
33MHz async PCI frequency:
PLB = 133:
=> 32 <= 44.3 <= 65 (div = 3)
PLB = 166:
=> 32 <= 55.3 <= 65 (div = 3)
66MHz async PCI frequency:
PLB = 133:
=> 65 <= 66.5 <= 132 (div = 2)
PLB = 166:
=> 65 <= 83 <= 132 (div = 2)
Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Mon, 15 Oct 2007 09:29:33 +0000 (11:29 +0200)]
ppc4xx: Fix incorrect 33/66MHz PCI clock log-message on Sequoia & Yosemite
The BCSR status bit for the 66MHz PCI operation was correctly
addressed (MSB/LSB problem). Now the correct currently setup
PCI frequency is displayed upon bootup.
This patch also fixes this problem on Rainier & Yellowstone, since these
boards use the same souce code as Sequoia & Yosemite do.
Signed-off-by: Stefan Roese <sr@denx.de>
Martin Krause [Wed, 26 Sep 2007 15:55:56 +0000 (17:55 +0200)]
TQM860M: adjust for doubled flash sector size.
Adjust flash map to support the new S29GLxxN (N-Type) Flashes with
doubled sector size.
Signed-off-by: Martin Krause <martin.krause@tqs.de>
Jens Gehrlein [Wed, 26 Sep 2007 15:55:54 +0000 (17:55 +0200)]
TQM8xx: Fix CAN timing.
Signed-off-by: Martin Krause <martin.krause@tqs.de>
Martin Krause [Thu, 27 Sep 2007 12:54:36 +0000 (14:54 +0200)]
TQM866M: fix SDRAM refresh
At 133 MHz the current SDRAM refresh rate is too fast
(measured 4 * 1.17 us).
CFG_MAMR_PTA changes from 39 to 97. This result
in a refresh rate of 4 * 7.8 us at the default clock
50 MHz. At 133 MHz the value will be then 4 * 2.9 us.
This is a compromise until a new method is found to
adjust the refresh rate.
Signed-off-by: Martin Krause <martin.krause@tqs.de>
Martin Krause [Wed, 26 Sep 2007 15:55:55 +0000 (17:55 +0200)]
TQM866M: adjust for doubled flash sector size.
Adjust flash map to support the new S29GLxxN (N-Type) Flashes with
doubled sector size.
Signed-off-by: Martin Krause <martin.krause@tqs.de>
Michal Simek [Sun, 14 Oct 2007 14:12:29 +0000 (16:12 +0200)]
[FIX] XUPV2P change command handling
and remove code violation
Michal Simek [Sun, 14 Oct 2007 12:33:32 +0000 (14:33 +0200)]
Merge git://www.denx.de/git/u-boot
Michal Simek [Sun, 14 Oct 2007 12:31:47 +0000 (14:31 +0200)]
Merge ../master/
Wolfgang Denk [Sat, 13 Oct 2007 22:13:19 +0000 (00:13 +0200)]
Prepare for 1.3.0-rc3 release
Signed-off-by: Wolfgang Denk <wd@denx.de>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 29 Sep 2007 11:41:37 +0000 (13:41 +0200)]
Fix warning differ in signedness in cpu/pxa/mmc.c
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Wolfgang Denk [Sat, 13 Oct 2007 21:51:14 +0000 (23:51 +0200)]
Fix warning differ in signedness in board/mpl/vcma9/vcma9.c
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sat, 13 Oct 2007 21:01:27 +0000 (23:01 +0200)]
Merge branch 'master' of git://denx.de/git/u-boot-avr32
Wolfgang Denk [Sat, 13 Oct 2007 20:57:43 +0000 (22:57 +0200)]
Merge branch 'merge' of git://denx.de/git/u-boot-microblaze
Wolfgang Denk [Sat, 13 Oct 2007 19:50:12 +0000 (21:50 +0200)]
Merge branch 'master' of git://denx.de/git/u-boot-microblaze
Wolfgang Denk [Sat, 13 Oct 2007 19:40:23 +0000 (21:40 +0200)]
Merge branch 'master' of git://denx.de/git/u-boot-nand-flash
Wolfgang Denk [Sat, 13 Oct 2007 19:15:39 +0000 (21:15 +0200)]
Coding Style cleanup.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sat, 13 Oct 2007 16:48:23 +0000 (18:48 +0200)]
Merge branch 'master' of git://denx.de/git/u-boot-arm
Wolfgang Denk [Fri, 12 Oct 2007 13:49:39 +0000 (15:49 +0200)]
GP3 SSA: enable RTC
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Wed, 10 Oct 2007 14:39:09 +0000 (16:39 +0200)]
Merge branch 'master' of /.automount/castor-vlab/root/home/wd/git/u-boot/master/
Wolfgang Denk [Wed, 10 Oct 2007 14:31:06 +0000 (16:31 +0200)]
Merge branch 'hellrosa_i2c' of /home/gjb/git/u-boot
Wolfgang Denk [Wed, 10 Oct 2007 14:23:23 +0000 (16:23 +0200)]
Merge branch 'tqm5200_default_env' of /home/tur/git/u-boot
Grzegorz Bernacki [Tue, 9 Oct 2007 11:58:24 +0000 (13:58 +0200)]
[ads5121] EEPROM support added.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Haavard Skinnemoen [Sat, 6 Oct 2007 16:55:35 +0000 (18:55 +0200)]
AVR32: Initialize bi_flash* in board_init_r
The ATSTK1000-specific flash driver intializes bi_flashstart,
bi_flashsize and bi_flashoffset, but other flash drivers, like the CFI
driver, don't.
Initialize these in board_init_r instead so that things will still be
set up correctly when we switch to the CFI driver.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Marian Balakowicz [Fri, 5 Oct 2007 08:40:54 +0000 (10:40 +0200)]
tqm5200: Fix CONFIG_CMD_PCI typo in board config file.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Bartlomiej Sieka [Fri, 5 Oct 2007 07:46:06 +0000 (09:46 +0200)]
CM5200: Fix missing null-termination in hostname manipulation code
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
Peter Pearse [Thu, 4 Oct 2007 10:00:44 +0000 (11:00 +0100)]
Merge with git://www.denx.de/git/u-boot.git
Haavard Skinnemoen [Tue, 2 Oct 2007 17:09:01 +0000 (19:09 +0200)]
Fix memtest breakage
CFG_MEMTEST_START uses weird magic involving gd, which fails to
compile. Use hardcoded values instead (we actually know how much RAM
we have on board.)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Haavard Skinnemoen [Tue, 2 Oct 2007 17:05:53 +0000 (19:05 +0200)]
Merge commit 'origin/master'
Stefan Roese [Tue, 2 Oct 2007 09:47:13 +0000 (11:47 +0200)]
Merge with git://www.denx.de/git/u-boot.git
Stefan Roese [Tue, 2 Oct 2007 09:44:46 +0000 (11:44 +0200)]
ppc4xx: Coding style cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Tue, 2 Oct 2007 09:44:19 +0000 (11:44 +0200)]
ppc4xx: lwmon5: Remove watchdog for now, since not fully tested yet
Signed-off-by: Stefan Roese <sr@denx.de>
Grzegorz Bernacki [Mon, 1 Oct 2007 07:51:50 +0000 (09:51 +0200)]
Program EPLD to force full duplex mode for PHY.
EPLD forces modes of PHY operation. By default full duplex is turned off.
This fix turns it on.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Timo Ketola [Mon, 24 Sep 2007 11:50:32 +0000 (14:50 +0300)]
Bugfix: Use only one PTD for one endpoint
Original isp116x-hcd code prepared multiple PTDs for longer than 16
byte transfers for one endpoint. That is unnecessary because the
ISP116x is able to split long data from one PTD into multiple
transactions based on the buffer size of the endpoint. It also caused
serious problems if the endpoint NAKed some of the transactions. In
that case ISP116x wouldn't notice that the other PTDs were for the same
endpoint and would try the other PTDs possibly out of order. That would
break the whole transfer.
This patch makes isp116x_submit_job to use one PTD for one transfer.
Signed-off-by: Timo Ketola <timo.ketola@exertus.fi>
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
Jean-Christophe PLAGNIOL-VILLARD [Thu, 27 Sep 2007 21:27:47 +0000 (23:27 +0200)]
Fix missing DECLARE_GLOBAL_DATA_PTR on CONFIG_LPC2292 in serial
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Stefan Roese [Thu, 27 Sep 2007 11:48:24 +0000 (13:48 +0200)]
Merge branch 'master' of /home/stefan/git/u-boot/lwmon5
Stefan Roese [Tue, 11 Sep 2007 12:12:55 +0000 (14:12 +0200)]
ppc4xx: lwmon5: Change GPIO 58 to default to low (watchdog test)
Signed-off-by: Stefan Roese <sr@denx.de>
Ed Swarthout [Wed, 26 Sep 2007 21:35:54 +0000 (16:35 -0500)]
85xx io out functions need sync after write.
This fixes the mc146818 rtc_read/write functions for 85xx.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Wolfgang Denk [Tue, 25 Sep 2007 22:13:14 +0000 (00:13 +0200)]
Merge ... git+ssh://gemini_vpn/home/wd/git/u-boot/master
Grant Likely [Tue, 25 Sep 2007 21:48:05 +0000 (15:48 -0600)]
Fpga: fix incorrect test of CFG_FPGA_XILINX macro
CFG_FPGA_XILINX is a bit value used to test against the value in
CONFIG_FPGA. Testing for a value will always return TRUE. I don't
think that is the intention in this code.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Kim Phillips [Mon, 24 Sep 2007 19:43:43 +0000 (14:43 -0500)]
Merge branch 'master' of git://denx.de/git/u-boot
Michal Simek [Sun, 23 Sep 2007 22:41:30 +0000 (00:41 +0200)]
[FIX] change command handling and removing code violation
Michal Simek [Sun, 23 Sep 2007 22:36:06 +0000 (00:36 +0200)]
[FIX] change sets of commands
because changing of command handling brings
compilation problems
Michal Simek [Sun, 23 Sep 2007 22:30:42 +0000 (00:30 +0200)]
[FIX] Email reparation & Copyright
Both codes are written by myself without any
support from CTU
Michal Simek [Sun, 23 Sep 2007 22:25:11 +0000 (00:25 +0200)]
[PATCH] Change macro name for UartLite
because PowerPC 405 can use UartLite as console
Michal Simek [Sun, 23 Sep 2007 22:21:19 +0000 (00:21 +0200)]
[PATCH] Add support for design without interrupt controller
Polling timer
Michal Simek [Sun, 23 Sep 2007 22:19:48 +0000 (00:19 +0200)]
[FIX] resolve problem with cpu without barrel shifter
Michal Simek [Sun, 23 Sep 2007 22:18:46 +0000 (00:18 +0200)]
[FIX] repair email address
Michal Simek [Sun, 23 Sep 2007 22:17:42 +0000 (00:17 +0200)]
[FIX] repair MFSL commands
Michal Simek [Sun, 23 Sep 2007 22:08:37 +0000 (00:08 +0200)]
synchronizition with mainline
Michal Simek [Sun, 23 Sep 2007 22:04:22 +0000 (00:04 +0200)]
Merge ../u-boot
Wolfgang Denk [Sat, 22 Sep 2007 22:47:01 +0000 (00:47 +0200)]
Merge ... /home/wd/git/u-boot/custodian/u-boot-usb
Wolfgang Denk [Wed, 19 Sep 2007 22:04:14 +0000 (00:04 +0200)]
v1.3.0-rc2
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Tue, 18 Sep 2007 19:39:39 +0000 (21:39 +0200)]
Merge ... git+ssh://gemini_vpn/home/wd/git/u-boot/master
Wolfgang Denk [Tue, 18 Sep 2007 19:36:35 +0000 (21:36 +0200)]
Avoid compiler warning.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Grant Likely [Tue, 18 Sep 2007 18:24:57 +0000 (12:24 -0600)]
Bugfix: remove embedded null (\0) from CFG_BOOTFILE macro in TQM8540_config
/bin/bash and /bin/dash (which /bin/sh is linked to on ubuntu) handle embedded
nulls in a string differently. For example, the following statement:
echo "this is a string\0" > afile
Will produce the following with /bin/bash:
"this is a string\0"
But with /bin/dash, will produce:
"this is a string
Bug fixed by moving the embedded null out of the makefile and into the
config header. Also renamed the macro to avoid usage colision with the same
macro used by other board ports.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Wolfgang Denk [Tue, 18 Sep 2007 15:40:27 +0000 (17:40 +0200)]
MCC200: fix build warning
The MCC200 board config file includes version.h for some customer-
specific setting, which causes warnings with "make depend"; build
version.h before depend.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Peter Pearse [Tue, 18 Sep 2007 12:07:54 +0000 (13:07 +0100)]
Move coloured led API to status_led.h
Improve indentation in drivers/at45.c
Peter Pearse [Tue, 18 Sep 2007 10:12:58 +0000 (11:12 +0100)]
Merge with git://www.denx.de/git/u-boot.git
Eirik Aanonsen [Tue, 18 Sep 2007 06:47:20 +0000 (08:47 +0200)]
Update atstk1002 bootargs.
Updates to atstk1002 U-Boot header file:
- Changed bootargs:
* Set the bootargs for at1002 to point to the SD-card partition instead
* ... of the boot flash.
* Removing the rootfstype since that argument are not needed.
Signed-off-by: Eirik Aanonsen <eaa@wprmedical.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Eirik Aanonsen [Wed, 12 Sep 2007 11:32:37 +0000 (13:32 +0200)]
Add some comments to clocks in atstk1002.h
This patch applies some clarifying comments to how the different
clocks are setup according to atstk1002.h Some of the previous
comments where stating wrongful information.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
projects / platform / kernel / u-boot.git / log