Rob Herring [Mon, 3 Dec 2012 03:00:29 +0000 (21:00 -0600)]
pxe: add ipappend support
Add ipappend support to pass network device information to the kernel.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Joe Hershberger [Mon, 24 Jun 2013 22:21:04 +0000 (17:21 -0500)]
net: Fix build regression in cmd_pxe.c
Not all boards define an SOC. As a result, we can't depend on that.
This was introduced in
39f985536d3f0df5dba32c15b64ba2b5d32dd296
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Rob Herring [Mon, 3 Dec 2012 03:00:28 +0000 (21:00 -0600)]
pxe: add support for per arch and SoC default paths
A pxelinux server setup for "default" menu is typically an x86 binary.
This does not work well with a mixed architecture setup. Extend the default
search to look for default-<arch>-<soc> and then default-<arch> before
falling back to just "default".
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Rob Herring [Mon, 3 Dec 2012 03:00:27 +0000 (21:00 -0600)]
pxe: add support for ontimeout token
ontimeout is similar to default, but is the selection on menu timeout.
This is how cobbler sets a default. The label default is supposed to be
the default selection when <enter> is pressed. If both default and
ontimeout are set, last one parsed wins.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Rob Herring [Mon, 3 Dec 2012 03:00:26 +0000 (21:00 -0600)]
pxe: simplify menu display and selection
Menus with lots of entries and long append lines are hard to read.
Just show a numbered list using the label or name and make the choice
by entering the number.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Rob Herring [Mon, 3 Dec 2012 03:00:25 +0000 (21:00 -0600)]
pxe: always display a menu when present
The prompt flag is for displaying a "boot:" prompt in pxelinux. This
doesn't make sense for u-boot as we don't support the pxelinux command
interface. So we should just ignore prompt statements and always show the
menu if a menu is present.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Rob Herring [Mon, 3 Dec 2012 19:17:21 +0000 (13:17 -0600)]
pxe: try bootz if bootm fails to find a valid image
Standard pxelinux servers will typically use a zImage rather than u-boot
image format, so fallback to bootz if bootm fails.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Rob Herring [Mon, 3 Dec 2012 03:00:23 +0000 (21:00 -0600)]
bootz: un-staticize do_bootz
Make do_bootz available for other functions like do_bootm is.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Rob Herring [Mon, 3 Dec 2012 03:00:22 +0000 (21:00 -0600)]
pxe: fix handling of different localboot values
Add support for value of -1 For localboot. A value of -1 means return to
u-boot prompt.
The localboot value is often 0, so we need to distinguish the value from
localboot being selected. A value of greater than or equal to 0 means
attempt local boot command.
If localboot is selected, we don't want to try other entries.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Rob Herring [Mon, 3 Dec 2012 03:00:21 +0000 (21:00 -0600)]
pxe: make string parameters const
Convert a bunch of string parameters to be const.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Rob Herring [Mon, 3 Dec 2012 03:00:20 +0000 (21:00 -0600)]
pxe: Use ethact setting for pxe
Get the MAC address using eth_getenv_enetaddr_by_index so that the MAC
address of ethact is used. This enables using the a NIC other than the
first one for PXE boot.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Yegor Yefremov [Wed, 28 Nov 2012 10:15:18 +0000 (11:15 +0100)]
net: add ICPlus PHY driver
The driver code was taken from Linux kernel source:
drivers/net/phy/icplus.c
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Yegor Yefremov [Wed, 28 Nov 2012 10:15:17 +0000 (11:15 +0100)]
phy: export genphy_parse_link()
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Henrik Nordström [Sun, 25 Nov 2012 11:41:36 +0000 (12:41 +0100)]
net: Add sunxi (Allwinner) wemac driver
This patch adds support for the WEMAC, the ethernet controller included
in the Allwinner A10 SoC. It will get used in the upcoming A10 board
support.
From: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Bo Shen [Wed, 24 Apr 2013 02:46:16 +0000 (10:46 +0800)]
checkpatch: add ignore for network block comment style checking
When use checkpatch.pl to check network related patch, it will report
--->8---
WARNING: networking block comments don't use an empty /* line,
use /* Comment...
---<8---
So, add --ignore NETWORKING_BLOCK_COMMENT_STYLE into .checkpatch.conf
This will help to keep all driver include network related driver use
the same comment style
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Tom Rini [Sat, 22 Jun 2013 11:38:12 +0000 (07:38 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
Albert ARIBAUD [Tue, 11 Jun 2013 12:17:35 +0000 (14:17 +0200)]
arm: optimize relocate_code routine
Use section symbols directly
Drop support for R_ARM_ABS32 record types
Eliminate unneeded intermediate registers
Optimize relocation table iteration
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Albert ARIBAUD [Tue, 11 Jun 2013 12:17:34 +0000 (14:17 +0200)]
arm: make __rel_dyn_{start, end} compiler-generated
This change is only done where needed: some linker
scripts may contain relocation symbols yet remain
unchanged.
__rel_dyn_start and __rel_dyn_end each requires
its own output section; putting them in relocation
sections changes their flags and breaks relocation.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Albert ARIBAUD [Tue, 11 Jun 2013 12:17:33 +0000 (14:17 +0200)]
arm: make __image_copy_{start, end} compiler-generated
This change is only done where needed: some linker
scripts may contain __image_copy_{start,end} yet
remain unchanged.
Also, __image_copy_end needs its own section; putting
it in relocation sections changes their flags and makes
relocation break.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Albert ARIBAUD [Tue, 11 Jun 2013 12:17:32 +0000 (14:17 +0200)]
arm: generalize lib/bss.c into lib/sections.c
File arch/arm/lib/bss.c was initially defined for BSS only,
but is now going to also contain definitions for other
section-boundary-related symbols, so rename it for better
accuracy.
Also, remove useless 'used' attributes.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Albert ARIBAUD [Tue, 11 Jun 2013 12:17:31 +0000 (14:17 +0200)]
remove all references to .dynsym
Discard all .dynsym sections from linker scripts
Remove all __dynsym_start definitions from linker scripts
Remove all __dynsym_start references from the codebase
Note: this touches include/asm-generic/sections.h, which
is not ARM-specific, but actual uses of __dynsym_start
are only in ARM, so this patch can safely go through
the ARM repository.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Albert ARIBAUD [Tue, 11 Jun 2013 12:17:30 +0000 (14:17 +0200)]
arm: ensure u-boot only uses relative relocations
Add a Makefile target ('checkarmreloc') which
fails if the ELF binary contains relocation records
of types other than R_ARM_RELATIVE.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Chunhe Lan [Fri, 14 Jun 2013 08:21:48 +0000 (16:21 +0800)]
powerpc/85xx: Add P1023RDB board support
P1023RDB Specification:
-----------------------
Memory subsystem:
512MB DDR3 (Fixed DDR on board)
64MB NOR flash
128MB NAND flash
Ethernet:
eTSEC1: Connected to Atheros AR8035 GETH PHY
eTSEC2: Connected to Atheros AR8035 GETH PHY
PCIe:
Three mini-PCIe slots
USB:
Two USB2.0 Type A ports
I2C:
AT24C08 8K Board EEPROM (8 bit address)
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Prabhakar Kushwaha [Thu, 13 Jun 2013 04:44:00 +0000 (10:14 +0530)]
powerpc/mpc85xx:Disable Debug TLB entry before init_tlbs
init_tlbs() initialize all the TLB entries required for the system.
So disable DEBUG TLB entry before TLB entries initialization.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
York Sun [Fri, 31 May 2013 15:48:04 +0000 (08:48 -0700)]
powerpc/pixis: Fix pixis help message
"pixis_reset help" command prints the message without a new line "\n",
which makes the prompt on the same line.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Chris Packham [Sun, 26 May 2013 22:51:46 +0000 (10:51 +1200)]
powerpc/CoreNet: Allow pbl images to take u-boot images != 512K
Instead of assuming that SYS_TEXT_BASE is 0xFFF80000 calculate the initial
pbl command offset by subtracting the image size from the top of the
24-bit address range. Also increase the size of the memory buffer to
accommodate a larger output image.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Axel Lin [Sun, 26 May 2013 07:00:30 +0000 (15:00 +0800)]
powerpc: mpc85xx/mpc86xx: Fix off-by-one boundary checking with ARRAY_SIZE
If a variable is used as array subscript, it's valid value range is
0 ... ARRAY_SIZE -1.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Ying Zhang [Mon, 20 May 2013 06:07:26 +0000 (14:07 +0800)]
Makefile: move the common makefile line to public area
Move the common makefile line shared by the SPL and non-SPL to the public area,
so that we can avoid excessive SPL symbols. Some of them will be used by the
SPL later.
This patch is on top of the patch "common/Makefile: Add new symbol
CONFIG_SPL_ENV_SUPPORT for environment in SPL".
Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Ying Zhang [Mon, 20 May 2013 06:07:25 +0000 (14:07 +0800)]
common/Makefile: Add new symbol CONFIG_SPL_ENV_SUPPORT for environment in SPL
There will need the environment in SPL for reasons other than network
support (in particular, hwconfig contains info for how to set up DDR).
Add a new symbol CONFIG_SPL_ENV_SUPPORT to replace CONFIG_SPL_NET_SUPPORT
for environment in common/Makefile.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: Tom Rini <trini@ti.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Ying Zhang [Fri, 7 Jun 2013 09:25:16 +0000 (17:25 +0800)]
powerpc/mpc85xx: modify the functionality clear_bss and aligning the end address of the BSS
There will clear the BSS in the function clear_bss(), the reset address of
the BSS started from the __bss_start, and increased by four-byte increments,
finally stoped depending on the address is equal to the _bss_end. If the end
address __bss_end is not alignment to 4byte, it will be an infinite loop.
1. The reset action stoped depending on the reset address is greater
than or equal the end address of the BSS.
2. The end address of the BSS should be 4byte aligned. Because the reset unit
is 4 Bytes.
This patch is on top of the patch "powerpc/mpc85xx: support application
without resetvec segment in the linker script".
Signed-off-by: Ying Zhang <b40530@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Ying Zhang [Mon, 20 May 2013 06:07:23 +0000 (14:07 +0800)]
powerpc/mpc85xx: support application without resetvec segment in the linker script
For SD/SPI 2-stage bootloader, the On-Chip Rom code loads the SPL into L2 SRAM,
then jump to it to begin execution. After that, the SPL loads the final uboot
image into DDR, then jump to it to begin execution. The segment .resetvec in
the SPL and in final U-boot is useless.
So, add new symbols CONFIG_SYS_MPC85XX_NO_RESETVEC for this application.
If CONFIG_SYS_MPC85XX_NO_RESETVEC is set, the segment .resetvec is excluded
and the segment .bootpg is placed in the previous 4K of the segment .text.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Prabhakar Kushwaha [Fri, 17 May 2013 08:52:34 +0000 (14:22 +0530)]
board/p1010rdb: Fix PCIe TLB creation on CONFIG_PCI define
PCIe TLB should be created with CONFIG_PCI defined
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Prabhakar Kushwaha [Fri, 17 May 2013 08:10:52 +0000 (13:40 +0530)]
board/b4860qds: Relax NOR flash teadc timing parameter
Relax parameters to give address latching more time to setup.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Scott Wood [Wed, 15 May 2013 22:50:13 +0000 (17:50 -0500)]
powerpc/mpc85xx: work around erratum A-006593
Erratum A-006593 is "Atomic store may report failure but still allow
the store data to be visible".
The workaround is: "Set CoreNet Platform Cache register CPCHDBCR0 bit
21 to 1'b1. This may have a small impact on synthetic write bandwidth
benchmarks but should have a negligible impact on real code."
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Mingkai Hu [Thu, 16 May 2013 02:18:13 +0000 (10:18 +0800)]
fsl_ifc: add support for different IFC bank count
Calculate reserved fields according to IFC bank count
1. Move csor_ext register behind csor register and fix res offset
2. Move ifc bank count to config_mpc85xx.h to support 8 bank count
3. Guard fsl_ifc.h with CONFIG_FSL_IFC macro to eliminate the compile
error on some devices that does not have IFC controller.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Liu Gang [Tue, 7 May 2013 08:30:50 +0000 (16:30 +0800)]
powerpc/t4qds: Slave module for boot from SRIO and PCIE
When a T4 board boots from SRIO or PCIE, it needs to finish these processes:
1. Set all the cores in holdoff status.
2. Set the boot location to one PCIE or SRIO interface by RCW.
3. Set a specific TLB entry for the boot process.
4. Set a LAW entry with the TargetID of one PCIE or SRIO for the boot.
5. Set a specific TLB entry in order to fetch ucode and ENV from
master.
6. Set a LAW entry with the TargetID one of the PCIE ports for
ucode and ENV.
7. Slave's u-boot image should be generated specifically by
make xxxx_SRIO_PCIE_BOOT_config.
This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.
For more information about the feature of Boot from SRIO/PCIE, please
refer to the document doc/README.srio-pcie-boot-corenet.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Liu Gang [Tue, 7 May 2013 08:30:49 +0000 (16:30 +0800)]
powerpc/t4qds: Enable master module for Boot from SRIO and PCIE
T4 can support the feature of Boot from SRIO/PCIE, and the macro
"CONFIG_SRIO_PCIE_BOOT_MASTER" will enable the master module of this feature
when building the u-boot image.
You can get some description about this macro in README file, and for more
information about the feature of Boot from SRIO/PCIE, please refer to the
document doc/README.srio-pcie-boot-corenet.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Liu Gang [Tue, 7 May 2013 08:30:48 +0000 (16:30 +0800)]
powerpc/b4860qds: Slave module for boot from SRIO and PCIE
When a b4860qds board boots from SRIO or PCIE, it needs to finish these
processes:
1. Set all the cores in holdoff status.
2. Set the boot location to one PCIE or SRIO interface by RCW.
3. Set a specific TLB entry for the boot process.
4. Set a LAW entry with the TargetID of one PCIE or SRIO for the boot.
5. Set a specific TLB entry in order to fetch ucode and ENV from
master.
6. Set a LAW entry with the TargetID one of the PCIE ports for
ucode and ENV.
7. Slave's u-boot image should be generated specifically by
make xxxx_SRIO_PCIE_BOOT_config.
This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.
For more information about the feature of Boot from SRIO/PCIE, please
refer to the document doc/README.srio-pcie-boot-corenet.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Liu Gang [Tue, 7 May 2013 08:30:47 +0000 (16:30 +0800)]
powerpc/b4860qds: Enable master module for boot from SRIO and PCIE
B4860QDS can support the feature of Boot from SRIO/PCIE, and the macro
"CONFIG_SRIO_PCIE_BOOT_MASTER" will enable the master module of this feature
when building the u-boot image.
You can get some description about this macro in README file, and for more
information about the feature of Boot from SRIO/PCIE, please refer to the
document doc/README.srio-pcie-boot-corenet.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Liu Gang [Tue, 7 May 2013 08:30:46 +0000 (16:30 +0800)]
powerpc/boot: Change the macro of Boot from SRIO and PCIE master module
Currently, the macro "CONFIG_SYS_FSL_SRIO_PCIE_BOOT_MASTER" can enable
the master module of Boot from SRIO and PCIE on a platform. But this
is not a silicon feature, it's just a specific booting mode based on
the SRIO and PCIE interfaces. So it's inappropriate to put the macro
into the file arch/powerpc/include/asm/config_mpc85xx.h.
Change the macro "CONFIG_SYS_FSL_SRIO_PCIE_BOOT_MASTER" to
"CONFIG_SRIO_PCIE_BOOT_MASTER", remove them from
arch/powerpc/include/asm/config_mpc85xx.h file, and add those macros
in configuration header file of each board which can support the
master module of Boot from SRIO and PCIE.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Liu Gang [Tue, 7 May 2013 08:30:45 +0000 (16:30 +0800)]
powerpc/doc: Update the README.srio-pcie-boot-corenet
1. Misalignment will be found in the doc/README.srio-pcie-boot-corenet
file when the tabs are set to 8 characters. And the standard for
u-boot should be 8 character tabs! So this issue should be amended.
2. Add a NOTE for the ENV parameters of the Slave.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Prabhakar Kushwaha [Tue, 7 May 2013 05:49:55 +0000 (11:19 +0530)]
powerpc/mpc85xx:Fix "boot page TLB" entry size for NAND SPL
e500v2 processor does not support 8K page size TLB entries.
So create new TLB entry only during NAND SPL boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Andy Fleming [Thu, 20 Jun 2013 19:54:33 +0000 (14:54 -0500)]
85xx: Change case of MPC85XX_PORBMSR_ROMLOC_SHIFT
All the other constants use lowercase 'x' in "MPC85xx", so we
duplicate that here.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Fabio Estevam [Sun, 21 Apr 2013 16:11:02 +0000 (13:11 -0300)]
powerpc: Use lower case for the core names
Freescale documentation presents the PowerPC core names in lower case, such as
"e300", "e500", "e600", etc.
Change the upper case occurrences into lower case so that the core names
reported in U-boot can match the ones from the documentation.
While at it also fix a checkpatch error:
ERROR: space prohibited before that close parenthesis ')'
#53: FILE: arch/powerpc/cpu/mpc86xx/cpu.c:81:
+ printf("e600 Core %d", (msscr0 & 0x20) ? 1 : 0 );
Reported-by: Heinz Wrobel <heinz.wrobel@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
York Sun [Fri, 19 Apr 2013 02:31:01 +0000 (19:31 -0700)]
powerpc/BSC9132: Add IFC bank count
BSC9132 has 3 IFC banks.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Priyanka Jain [Thu, 4 Apr 2013 09:10:32 +0000 (14:40 +0530)]
board/bsc9131rdb: Update default boot environment settings
BSC9131RDB has 1GB DDR.
Out of this, only 880MB is passed on to Linux via bootm_size.
Remaining
-16MB is reserved for PowerPC-DSP shared control area
-128MB is reserved for DSP private area.
Also 256MB, out of this 880MB is required for data communication between
PowerPC and DSP core.
For this bootargs are modified to pass parameter to create 1 hugetlb
page of 256MB via default_hugepagesz, hugepagesz and hugepages
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Priyanka Jain [Thu, 4 Apr 2013 04:01:54 +0000 (09:31 +0530)]
board/bsc9131rdb: Add DSP side tlb and laws
BSC9131RDB is a Freescale Reference Design Board for
BSC9131 SoC which is a integrated device that contains
one powerpc e500v2 core and one DSP starcore.
To support DSP starcore
-Creating LAW and TLB for DSP-CCSR space.
-Creating LAW for DSP-core subsystem M2 memory
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Priyanka Jain [Mon, 1 Apr 2013 06:42:45 +0000 (12:12 +0530)]
board/bsc9131rdb: Add targets for Sysclk 100MHz
BSC9131RDB supports Sysclk
-66MHz if jumper J16 is close (default state)
-100MHz if jumper J16 is open
Add targets
-BSC9131RDB_NAND_SYSCLK100 : for NAND boot at Sysclk 100MHz
-BSC9131RDB_SPIFLASH_SYSCLK100: for SPI boot at Sysclk 100MHz
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Prabhakar Kushwaha [Tue, 16 Apr 2013 07:58:40 +0000 (13:28 +0530)]
board/bsc9132qds:Add NAND boot support using new SPL format
- Add NAND boot target
- defines constants
- Add spl_minimal.c to initialise DDR
- update TLB, LAW entries as per NAND boot
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Prabhakar Kushwaha [Tue, 16 Apr 2013 07:58:25 +0000 (13:28 +0530)]
board/bsc9131rdb:Add NAND boot support using new SPL format
- Add NAND boot target
- defines constants
- Add spl_minimal.c to initialise DDR
- update TLB entries as per NAND boot
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Prabhakar Kushwaha [Tue, 16 Apr 2013 07:58:12 +0000 (13:28 +0530)]
board/p1010rdb:Add NAND boot support using new SPL format
- defines constants
- Add spl_minimal.c to initialise DDR
- update TLB entries as per NAND boot
- remove nand_spl support for P1010RDB
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Prabhakar Kushwaha [Tue, 16 Apr 2013 07:57:59 +0000 (13:27 +0530)]
powerpc/mpc85xx: new SPL support for IFC NAND
Linker script is not able find start.o binary. So add its absolute path in
u-boot-spl.lds. This change is similar to u-boot-nand.lds
common/Makefile: Avoid compiling unnecssary files
fsl_ifc_spl.c : It is is responsible for reading u-boot binary from
NAND flash and copying into DDR. It also transfer control from NAND SPL
to u-boot image present in DDR.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Prabhakar Kushwaha [Tue, 16 Apr 2013 07:57:44 +0000 (13:27 +0530)]
powerpc/mpc85xx:No NOR boot, do not compile IFC errata A003399
IFC errata A003399 is valid for IFC NOR boot i.e.if no on-board NOR flash or
no NOR boot, do not compile its workaround.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Mingkai Hu [Fri, 12 Apr 2013 07:56:28 +0000 (15:56 +0800)]
powerpc/mpc85xx: explicit cast the SDRAM size to type phys_size_t
To avoid sign extension problem, use explicit casting to cast
the SDRAM size to type phys_size_t, or else, if the SDRAM size
is 2G(0x80000000), it will be extended to 0xffffffff80000000
when phys_size_t is type 'unsigned long long'.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Andy Fleming [Mon, 17 Jun 2013 20:10:28 +0000 (15:10 -0500)]
85xx: Change clock-frequency compatible to 2.0
Accidentally applied an earlier version of the patch, which set
the compatible to "fsl,qoriq-clockgen-2", lacking the final
".0".
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Simon Guinot [Tue, 18 Jun 2013 13:14:50 +0000 (15:14 +0200)]
net2big_v2: initialize LEDs at startup
This patch allows to configure the net2big_v2 LEDs at startup (through
the GPIO extension bus). The front blue LED is enabled and the SATA rear
LEDs are configured to blink in relation with the SATA activity.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Simon Guinot [Tue, 18 Jun 2013 13:14:49 +0000 (15:14 +0200)]
LaCie/common: add support for the CPLD GPIO bus
This patch adds support for the CPLD GPIO bus found on some LaCie boards
(as the 2Big/5Big Network v2 and the 2Big NAS). This parallel GPIO bus
exposes two registers (address and data). Each of this register is made
up of several dedicated GPIOs. An extra GPIO is used to notify the CPLD
that the registers have been updated.
Mostly this bus is used to configure the LEDs on LaCie boards.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Simon Guinot [Tue, 18 Jun 2013 13:14:48 +0000 (15:14 +0200)]
net2big_v2: initialize I2C fan at startup
This patch ensures minimal cooling for the net2big_v2 by automatically
starting the I2C fan (GMT G762) at low speed (2800 RPM).
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Albert ARIBAUD [Wed, 19 Jun 2013 21:58:01 +0000 (23:58 +0200)]
Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'
Jim Lin [Fri, 17 May 2013 09:41:03 +0000 (17:41 +0800)]
NET: Fix system hanging if NET device is not installed
If we try to boot from NET device, NetInitLoop in net.c will be invoked.
If NET device is not installed, eth_get_dev() function will return
eth_current value, which is NULL.
When NetInitLoop is called, "eth_get_dev->enetaddr" will access
restricted memory area and therefore cause hanging.
This issue is found on Tegra30 Cardhu platform after adding
CONFIG_CMD_NET and CONFIG_CMD_DHCP in config header file.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Albert ARIBAUD [Wed, 19 Jun 2013 10:53:59 +0000 (12:53 +0200)]
Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'
Conflicts:
spl/Makefile
Dan Murphy [Thu, 13 Jun 2013 16:21:26 +0000 (11:21 -0500)]
arm: omap4: panda: Fix checkpatch on panda file
Fix the checkpatch warning on the panda.c file for leading
spaces.
Fix the CHECK warnings on the panda.c file for parenthesis alignment.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Dan Murphy [Thu, 13 Jun 2013 16:21:13 +0000 (11:21 -0500)]
arm: omap4: panda: Add reading of the board revision
Detect if we are running on a panda revision A1-A6,
or an ES panda board. This can be done by reading
the level of GPIOs and checking the processor revisions.
This should result in:
Panda 4430:
GPIO171, GPIO101, GPIO182: 0 1 1 => A1-A5
GPIO171, GPIO101, GPIO182: 1 0 1 => A6
Panda ES:
GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 0 1 1 => B1/B2
GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 1 1 1 => B3
Set the board name appropriately for the board revision that
is detected.
Update the findfdt macro to load the a4 device tree binary.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
[trini: %s/CONTROL_PADCONF_CORE/(*ctrl)->control_padconf_core_base/ and
formatting for that]
Signed-off-by: Tom Rini <trini@ti.com>
Dan Murphy [Tue, 11 Jun 2013 16:22:30 +0000 (11:22 -0500)]
arm: dra7xx: Update the EXTRA_ENV_SETTINGS
Update the EXTRA_ENV_SETTING for the dra7xx.
The console needs to be set to ttyO0 and the
findfdt needs to be updated to load the
dra7xx-evm.dtb file.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Dan Murphy [Thu, 6 Jun 2013 21:30:38 +0000 (16:30 -0500)]
arm: omap5_uevm: Correct the console sys prompt for 5432
Correct the console sys prompt to display the correct processor
and the corrent board
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reported-by: Lubomir Popov <lpopov@mm-sol.com>
Reviewed-by: Tom Rini <trini@ti.com>
Dan Murphy [Thu, 6 Jun 2013 18:27:06 +0000 (13:27 -0500)]
arm: omap: Add check for fdtfile in the findfdt macro
In the omap4, omap5 and am335x common files add a check to ensure that the fdtfile is
defined after the findfdt macro has run. If the file is not defined then warn the user that the
dtb file is not defined.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Heiko Schocher [Tue, 4 Jun 2013 09:00:57 +0000 (11:00 +0200)]
arm, am33xx: move uart soft reset code to common place
move uart soft reset code to common place and call
this function from board code, instead of copy and paste
this code for every board.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matt Porter <mporter@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Tom Rini <trini@ti.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Tom Rini <trini@ti.com>
[trini: Fix igep0033 build, remove 'regval' on pcm051]
Signed-off-by: Tom Rini <trini@ti.com>
Heiko Schocher [Tue, 4 Jun 2013 09:01:06 +0000 (11:01 +0200)]
arm, am335x: make mpu pll config configurable
upcoming support for siemens boards switches mpu pll clk in board
code. So make this configurable.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Heiko Schocher [Wed, 5 Jun 2013 05:47:56 +0000 (07:47 +0200)]
arm, am33xx: move rtc32k_enable() to common place
move rtc32k_enable() to common place so all am33xx boards can use it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matt Porter <mporter@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Tom Rini <trini@ti.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Simon Glass [Sun, 16 Jun 2013 14:46:49 +0000 (07:46 -0700)]
image: Use ENOENT instead of ENOMEDIUM for better compatibility
This error may not be defined on some platforms such as MacOS so host
compilation will fail. Use one of the more common errors instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Andreas Bießmann <andreas.devel@googlemail.com>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Rajeshwari Shinde [Fri, 24 May 2013 12:45:34 +0000 (18:15 +0530)]
MMC: DWMMC: Fix FIFO_DEPTH calculation
Current DWMMC driver used to give FIFO underrun/overrun error every 3rd time
for mmc rescan command.
In current code FIFO_DEPTH is getting calculated after reading the default FIFOTH
register and extracting the RX_WMARK bits from it i.e (RX_WMARK = FIFO_DEPTH/2 -1).
Instead of storing the correct value, we were recalculating the FIFO_DEPT each
time which is not correct.
Based on "[PATCH V9 3/9] DWMMC: Initialise dwmci and resolve EMMC read write issues"
http://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/160247
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Tom Rini [Fri, 14 Jun 2013 20:06:49 +0000 (16:06 -0400)]
Merge branch 'master' of git://denx.de/git/u-boot-mmc
Tom Rini [Fri, 14 Jun 2013 15:01:39 +0000 (11:01 -0400)]
Prepare v2013.07-rc1
Signed-off-by: Tom Rini <trini@ti.com>
Stephen Warren [Tue, 11 Jun 2013 21:14:03 +0000 (15:14 -0600)]
ARM: tegra: make use of negative ENV_OFFSET on NVIDIA boards
Use a negative value of CONFIG_ENV_OFFSET for all NVIDIA reference boards
that store the U-Boot environment in the 2nd eMMC boot partition. This
makes U-Boot agnostic to the size of the eMMC boot partition, which can
vary depending on which eMMC device was actually stuffed into the board.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Stephen Warren [Tue, 11 Jun 2013 21:14:02 +0000 (15:14 -0600)]
env_mmc: allow negative CONFIG_ENV_OFFSET
A negative value of CONFIG_ENV_OFFSET is treated as a backwards offset
from the end of the eMMC device/partition, rather than a forwards offset
from the start.
This is useful when a single board may be stuffed with different eMMC
devices, each of which has a different capacity, and you always want the
environment to be stored at the very end of the device (or eMMC boot
partition for example).
One example of this case is NVIDIA's Ventana reference board.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Stephen Warren [Tue, 11 Jun 2013 21:14:01 +0000 (15:14 -0600)]
mmc: report capacity for the selected partition
Enhance the MMC core to calculate the size of each MMC partition, and
update mmc->capacity whenever a partition is selected. This causes:
mmc dev 0 1 ; mmcinfo
... to report the size of the currently selected partition, rather than
always reporting the size of the user partition.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Stephen Warren [Tue, 11 Jun 2013 21:14:00 +0000 (15:14 -0600)]
README: document CONFIG_ENV_IS_IN_MMC
Describe the meaning of CONFIG_ENV_IS_IN_MMC, and all related defines that
must or can be set when using that option.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Andrew Gabbasov [Tue, 11 Jun 2013 15:34:22 +0000 (10:34 -0500)]
fsl_esdhc: Do not clear interrupt status bits until data processed
After waiting for the command completion event, the interrupt status
bits, that occured to be set by that time, are cleared by writing them
back. It is supposed, that it should be command related bits (command
complete and may be command errors).
However, in some cases the DMA already completes by that time before
the full transaction completes. The corresponding DINT bit gets set
and then cleared before even entering the loop, waiting for data part
completion. That waiting loop never gets this bit set, causing the
operation to hang. This is reported to happen, for example, for write
operation of 1 sector to upper area (block #7400000) of SanDisk Ultra II
8GB card.
The solution could be to explicitly clear only command related interrupt
status bits. However, since subsequent processing does not rely on
any command bits state, it could be easier just to remove clearing
of any bits at that point, leaving them all until all data processing
completes. After that the whole register will be cleared at once.
Also, on occasion, interrupts masking moved to before writing the command,
just for the case there should be no chance of interrupt between the first
command and interrupts masking.
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Fabio Estevam [Tue, 28 May 2013 18:09:42 +0000 (15:09 -0300)]
mmc: fsl_esdhc: Fix hang after 'save' command
Since commit
48e0b2bd (powerpc/esdhc: Correct judgement for DATA PIO mode)
we see mx6 systems to hang after doing a 'save' command.
Revert this commit since the original 'ifdef' logic from
7b43db92
(drivers/mmc/fsl_esdhc.c: fix compiler warnings) was the correct one.
Reported-by: Tapani Utriainen <tapani@technexion.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Ruud Commandeur [Wed, 22 May 2013 11:19:43 +0000 (13:19 +0200)]
mmc write bug fix
This patch fixes a bug related to mmc writes.
When doing fatwrites on an SD-Card, MMC bus problems can occur. Depending
on the size of the file, "MMC0: Bus busy timeout!" is reported, resulting
in an SD-Card that is no longer responding.
It appears to be, that set_cluster can be called with a size being zero.
That can be with a file that has a size being an exact multiple
(including 0) of the clustersize, but also for files that are smaller than
the size of one cluster.
The same problem occurs if the "mmc write" command is given with a block
count being 0.
By adding a check for the block count being zero in mmc_write_blocks
(drivers/mmc.c), this problem is solved.
Signed-off-by: Ruud Commandeur <rcommandeur@clb.nl>
Cc: Tom Rini <trini@ti.com>
Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Mats Karrman <Mats.Karrman@tritech.se>
Cc: Andy Fleming <afleming@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Jagannadha Sutradharudu Teki [Tue, 21 May 2013 09:31:36 +0000 (15:01 +0530)]
mmc: sdhci: Enable 8-bit bus width only for 3.0 spec onwards
CAP register don't have any information for 8-bit buswidth support
on 2.0 sdhci spec, only from 3.0 onwards bit[18] got this information.
Due to this misassignment in sdhci, mmc is setting 8-bit buswidth using
mmc_set_bus_width even if controller doesn't support.
Below change has code information.
"mmc: Properly determine maximum supported bus width"
(sha1:
7798f6dbd5e1a3030ed81a81da5dfb57c3307cac)
Bug log: <mmc plus and emmc cards)
-------
zynq-uboot> mmcinfo
Error detected in status(0x208100)!
Device: zynq_sdhci
Manufacturer ID: fe
.....
So enable 8-bit support only for 3.0 spec using CAP and for below 3.0
assign mmc->host_caps = MMC_MODE_8BIT on respective platform driver
if host have a support.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Bo Shen [Wed, 15 May 2013 01:38:16 +0000 (09:38 +0800)]
mmc: fix env in mmc with redundant compile error
The commit d196bd8 (env_mmc: add support for redundant environment)
introduce the following compile error when enable redundant
environment support with MMC
---8<---
env_mmc.c:149: error: 'env_t' has no member named 'flags'
env_mmc.c:248: error: 'env_t' has no member named 'flags'
env_mmc.c:248: error: 'env_t' has no member named 'flags'
env_mmc.c:250: error: 'env_t' has no member named 'flags'
env_mmc.c:250: error: 'env_t' has no member named 'flags'
env_mmc.c:252: error: 'env_t' has no member named 'flags'
env_mmc.c:252: error: 'env_t' has no member named 'flags'
env_mmc.c:254: error: 'env_t' has no member named 'flags'
env_mmc.c:254: error: 'env_t' has no member named 'flags'
env_mmc.c:267: error: 'env_t' has no member named 'flags'
make[1]: *** [env_mmc.o] Error 1
--->8---
Add this patch to fix it
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Michael Heimpold <mhei@heimpold.de>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Tom Rini [Thu, 13 Jun 2013 19:18:35 +0000 (15:18 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-spi
Tom Rini [Thu, 13 Jun 2013 19:16:15 +0000 (15:16 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
Small conflict over DRA7XX updates and adding SRAM_SCRATCH_SPACE_ADDR
Conflicts:
arch/arm/include/asm/arch-omap5/omap.h
Signed-off-by: Tom Rini <trini@ti.com>
Jagannadha Sutradharudu Teki [Fri, 24 May 2013 20:43:41 +0000 (02:13 +0530)]
sf: winbond: Correct the nr_blocks used for W25Q32DW
This patch corrected the nr_blocks used for W25Q32DW SPI flash.
nr_blcoks are incorrectly assigned on below patch
"sf: winbond: add W25Q32DW"
(sha1:
772ba15474f73adc942e817cc072b6e9750836cc)
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Jagannadha Sutradharudu Teki [Mon, 27 May 2013 07:20:50 +0000 (12:50 +0530)]
sf: winbond: Add support for W25Q80BW
Add support for Winbond W25Q80BW SPI flash.
This patch corrected the flash name, nr_blocks and
also commit message header from below patch.
"sf: winbond: add W25Q32"
(sha1:
c969abc47033d6f810d3c9dbdb994ea9d691d038)
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Jagannadha Sutradharudu Teki [Sat, 25 May 2013 17:33:11 +0000 (23:03 +0530)]
sf: spansion: Update the name for S25FL256S flash
As the per the ID tabl the flash is under Uniform 64-kB sector
architecture, hence updated with proper name.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Axel Lin [Thu, 13 Jun 2013 08:21:42 +0000 (16:21 +0800)]
spi: tegra20_sflash: Remove redundant code to set bus and cs of struct spi_slave
It's done in spi_alloc_slave(), thus remove the redundant code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Axel Lin [Thu, 13 Jun 2013 08:17:47 +0000 (16:17 +0800)]
spi: tegra114_spi: Convert to use spi_alloc_slave()
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Axel Lin [Tue, 11 Jun 2013 13:57:31 +0000 (21:57 +0800)]
spi: armada100_spi: Remove unnecessary NULL test for dout and din
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Naveen Krishna Chatradhi [Fri, 5 Apr 2013 22:21:39 +0000 (15:21 -0700)]
power: exynos-tmu: use the mux_addr bit fields in tmu_control register
This patch implements the mux_addr bit fields defined in tmu_control
register (used for debugging purpose)
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Vadim Bendebury <vbendeb@google.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Naveen Krishna Chatradhi [Fri, 5 Apr 2013 22:21:38 +0000 (15:21 -0700)]
power: exynos-tmu: fix warnings and clean up code
This patch does the folowing
1. change the data types for unsigned int variable to unsigned
2. change the tmu_base type to struct exynos5_tmu_reg *
3. Add timer functionality for get_cur_temp()
4. error handling in the get_tmu_fdt_values()
5. Add check for curr_temp reading
6. some cosmotic changes.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Vadim Bendebury <vbendeb@google.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Amar [Sat, 27 Apr 2013 06:13:00 +0000 (11:43 +0530)]
COMMON: MMC: Command to support EMMC booting and to resize EMMC boot partition
This patch adds commands to access(open/close) and resize boot partitions on EMMC.
Signed-off-by: Amar <amarendra.xt@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Amar [Sat, 27 Apr 2013 06:12:59 +0000 (11:42 +0530)]
SMDK5250: Enable EMMC booting
This patch adds support for EMMC booting on SMDK5250.
Signed-off-by: Amar <amarendra.xt@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Amar [Sat, 27 Apr 2013 06:12:58 +0000 (11:42 +0530)]
MMC: APIs to support resize of EMMC boot partition
This patch adds APIs to access(open / close) and to resize boot partiton of EMMC.
Signed-off-by: Amar <amarendra.xt@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Amar [Sat, 27 Apr 2013 06:12:57 +0000 (11:42 +0530)]
SMDK5250: Initialise and Enable DWMMC, support FDT and non-FDT
This patch enables and initialises DWMMC for SMDK5250.
Supports both FDT and non-FDT. This patch creates a new file
'exynos5-dt.c' meant for FDT support.
exynos5-dt.c: This file shall contain all code which supports FDT.
Any addition of FDT support for any module needs to be
added in this file.
smdk5250.c: This file shall contain the code which supports non-FDT.
version. Any addition of non-FDT support for any module
needs to be added in this file.
May be, the file smdk5250.c can be removed in near future
when non-FDT is not required.
The Makefile is updated to compile only one of the files
exynos5-dt.c / smdk5250.c based on FDT configuration.
NOTE:
Please note that all additions corresponding to FDT need to be added into the
file exynos5-dt.c.
At same time if non-FDT support is required then add the corresponding
updations into smdk5250.c.
Signed-off-by: Amar <amarendra.xt@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Amar [Sat, 27 Apr 2013 06:12:56 +0000 (11:42 +0530)]
EXYNOS5: DWMMC: Initialise the local variable to avoid unwanted results.
This patch initialises the local variable 'shift' to zero.
The uninitialised local variable 'shift' had garbage value and was
resulting in unwnated results in the functions exynos5_get_mmc_clk()
and exynos4_get_mmc_clk().
Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Amar [Sat, 27 Apr 2013 06:12:55 +0000 (11:42 +0530)]
EXYNOS5: DWMMC: Added FDT support for DWMMC
This patch adds FDT support for DWMMC, by reading the DWMMC node data
from the device tree and initialising DWMMC channels as per data
obtained from the node.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Amar [Sat, 27 Apr 2013 06:12:54 +0000 (11:42 +0530)]
DWMMC: Initialise dwmci and resolve EMMC read write issues
This patch enumerates dwmci and set auto stop command during
dwmci initialisation.
EMMC read/write is not happening in current implementation
due to improper fifo size computation. Hence modified the fifo size
computation to resolve EMMC read write issues.
Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Amar [Sat, 27 Apr 2013 06:12:53 +0000 (11:42 +0530)]
EXYNOS5: FDT: Add DWMMC device node data
This patch adds DWMMC device node data for exynos5.
This patch also adds binding file for DWMMC device node.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>