net: stmmac: Prevent DSA tags from breaking COE

[ Upstream commit c2945c435c999c63e47f337bc7c13c98c21d0bcc ]

Some DSA tagging protocols change the EtherType field in the MAC header
e.g.  DSA_TAG_PROTO_(DSA/EDSA/BRCM/MTK/RTL4C_A/SJA1105). On TX these tagged
frames are ignored by the checksum offload engine and IP header checker of
some stmmac cores.

On RX, the stmmac driver wrongly assumes that checksums have been computed
for these tagged packets, and sets CHECKSUM_UNNECESSARY.

Add an additional check in the stmmac TX and RX hotpaths so that COE is
deactivated for packets with ethertypes that will not trigger the COE and
IP header checks.

Fixes: 6b2c6e4a938f ("net: stmmac: propagate feature flags to vlan")
Cc: <stable@vger.kernel.org>
Reported-by: Richard Tresidder <rtresidd@electromag.com.au>
Link: https://lore.kernel.org/netdev/e5c6c75f-2dfa-4e50-a1fb-6bf4cdb617c2@electromag.com.au/
Reported-by: Romain Gantois <romain.gantois@bootlin.com>
Link: https://lore.kernel.org/netdev/c57283ed-6b9b-b0e6-ee12-5655c1c54495@bootlin.com/
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: stmmac: Tx coe sw fallback

[ Upstream commit 8452a05b2c633b708dbe3e742f71b24bf21fe42d ]

Add sw fallback of tx checksum calculation for those tx queues that
don't support tx checksum offloading. DW xGMAC IP can be synthesized
such that it can support tx checksum offloading only for a few
initial tx queues. Also as Serge pointed out, for the DW QoS IP, tx
coe can be individually configured for each tx queue.

So when tx coe is enabled, for any tx queue that doesn't support
tx coe with 'coe-unsupported' flag set will have a sw fallback
happen in the driver for tx checksum calculation when any packets to
be transmitted on these tx queues.

Signed-off-by: Rohan G Thomas <rohan.g.thomas@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: c2945c435c99 ("net: stmmac: Prevent DSA tags from breaking COE")
Signed-off-by: Sasha Levin <sashal@kernel.org>

soundwire: fix initializing sysfs for same devices on different buses

[ Upstream commit 8a8a9ac8a4972ee69d3dd3d1ae43963ae39cee18 ]

If same devices with same device IDs are present on different soundwire
buses, the probe fails due to conflicting device names and sysfs
entries:

  sysfs: cannot create duplicate filename '/bus/soundwire/devices/sdw:0:0217:0204:00:0'

The link ID is 0 for both devices, so they should be differentiated by
the controller ID. Add the controller ID so, the device names and sysfs entries look
like:

  sdw:1:0:0217:0204:00:0 -> ../../../devices/platform/soc@0/6ab0000.soundwire-controller/sdw-master-1-0/sdw:1:0:0217:0204:00:0
  sdw:3:0:0217:0204:00:0 -> ../../../devices/platform/soc@0/6b10000.soundwire-controller/sdw-master-3-0/sdw:3:0:0217:0204:00:0

[PLB changes: use bus->controller_id instead of bus->id]

Fixes: 7c3cd189b86d ("soundwire: Add Master registration")
Cc: stable@vger.kernel.org
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Mark Brown <broonie@kernel.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20231017160933.12624-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

soundwire: bus: introduce controller_id

[ Upstream commit 6543ac13c623f906200dfd3f1c407d8d333b6995 ]

The existing SoundWire support misses a clear Controller/Manager
hiearchical definition to deal with all variants across SOC vendors.

a) Intel platforms have one controller with 4 or more Managers.
b) AMD platforms have two controllers with one Manager each, but due
to BIOS issues use two different link_id values within the scope of a
single controller.
c) QCOM platforms have one or more controller with one Manager each.

This patch adds a 'controller_id' which can be set by higher
levels. If assigned to -1, the controller_id will be set to the
system-unique IDA-assigned bus->id.

The main change is that the bus->id is no longer used for any device
name, which makes the definition completely predictable and not
dependent on any enumeration order. The bus->id is only used to insert
the Managers in the stream rt context.

Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/stable/20231017160933.12624-2-pierre-louis.bossart%40linux.intel.com
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20231017160933.12624-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Stable-dep-of: 8a8a9ac8a497 ("soundwire: fix initializing sysfs for same devices on different buses")
Signed-off-by: Sasha Levin <sashal@kernel.org>

serial: core: set missing supported flag for RX during TX GPIO

[ Upstream commit 1a33e33ca0e80d485458410f149265cdc0178cfa ]

If the RS485 feature RX-during-TX is supported by means of a GPIO set the
according supported flag. Otherwise setting this feature from userspace may
not be possible, since in uart_sanitize_serial_rs485() the passed RS485
configuration is matched against the supported features and unsupported
settings are thereby removed and thus take no effect.

Cc: <stable@vger.kernel.org>
Fixes: 163f080eb717 ("serial: core: Add option to output RS485 RX_DURING_TX state via GPIO")
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240103061818.564-3-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

serial: core: Simplify uart_get_rs485_mode()

[ Upstream commit 7cda0b9eb6eb9e761f452e2ef4e81eca20b19938 ]

Simplify uart_get_rs485_mode() by using temporary variable for
the GPIO descriptor. With that, use proper type for the flags
of the GPIO descriptor.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231003142346.3072929-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 1a33e33ca0e8 ("serial: core: set missing supported flag for RX during TX GPIO")
Signed-off-by: Sasha Levin <sashal@kernel.org>

docs: kernel_feat.py: fix potential command injection

[ Upstream commit c48a7c44a1d02516309015b6134c9bb982e17008 ]

The kernel-feat directive passes its argument straight to the shell.
This is unfortunate and unnecessary.

Let's always use paths relative to $srctree/Documentation/ and use
subprocess.check_call() instead of subprocess.Popen(shell=True).

This also makes the code shorter.

This is analogous to commit 3231dd586277 ("docs: kernel_abi.py: fix
command injection") where we did exactly the same thing for
kernel_abi.py, somehow I completely missed this one.

Link: https://fosstodon.org/@jani/111676532203641247
Reported-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20240110174758.3680506-1-vegard.nossum@oracle.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

docs: sparse: add sparse.rst to toctree

[ Upstream commit c9ad95adc096f25004d4192258863806a68a9bc8 ]

Add sparst.rst to toctree, so it can be part of the docs build.

Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Suggested-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Min-Hua Chen <minhuadotchen@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20230902052512.12184-4-minhuadotchen@gmail.com
Stable-dep-of: c48a7c44a1d0 ("docs: kernel_feat.py: fix potential command injection")
Signed-off-by: Sasha Levin <sashal@kernel.org>

docs: sparse: move TW sparse.txt to TW dev-tools

[ Upstream commit 253f68f413a87a4e2bd93e61b00410e5e1b7b774 ]

Follow Randy's advice [1] to move
Documentation/translations/zh_TW/sparse.txt
to
Documentation/translations/zh_TW/dev-tools/sparse.txt

[1] https://lore.kernel.org/lkml/bfab7c5b-e4d3-d8d9-afab-f43c0cdf26cf@infradead.org/

Cc: Randy Dunlap <rdunlap@infradead.org>
Suggested-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Min-Hua Chen <minhuadotchen@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20230902052512.12184-2-minhuadotchen@gmail.com
Stable-dep-of: c48a7c44a1d0 ("docs: kernel_feat.py: fix potential command injection")
Signed-off-by: Sasha Levin <sashal@kernel.org>

Linux 6.6.14

Link: https://lore.kernel.org/r/20240122235812.238724226@linuxfoundation.org
Tested-by: SeongJae Park <sj@kernel.org>
Tested-by: Luna Jernberg <droidbittin@gmail.com>
Tested-by: Takeshi Ogasawara <takeshi.ogasawara@futuring-girl.com>
Tested-by: Allen Pais <apais@linux.microsoft.com>
Tested-by: Justin M. Forbes <jforbes@fedoraproject.org>
Tested-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Link: https://lore.kernel.org/r/20240123174533.427864181@linuxfoundation.org
Tested-by: SeongJae Park <sj@kernel.org>
Tested-by: Kelsey Steele <kelseysteele@linux.microsoft.com>
Tested-by: Luna Jernberg <droidbittin@gmail.com>
Tested-by: Bagas Sanjaya <bagasdotme@gmail.com>
Tested-by: Ron Economos <re@w6rz.net>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Takeshi Ogasawara <takeshi.ogasawara@futuring-girl.com>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: kernelci.org bot <bot@kernelci.org>
Tested-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "Revert "md/raid5: Wait for MD_SB_CHANGE_PENDING in raid5d""

This reverts commit bed9e27baf52a09b7ba2a3714f1e24e17ced386d.

The original set [1][2] was expected to undo a suboptimal fix in [2], and
replace it with a better fix [1]. However, as reported by Dan Moulding [2]
causes an issue with raid5 with journal device.

Revert [2] for now to close the issue. We will follow up on another issue
reported by Juxiao Bi, as [2] is expected to fix it. We believe this is a
good trade-off, because the latter issue happens less freqently.

In the meanwhile, we will NOT revert [1], as it contains the right logic.

[1] commit d6e035aad6c0 ("md: bypass block throttle for superblock update")
[2] commit bed9e27baf52 ("Revert "md/raid5: Wait for MD_SB_CHANGE_PENDING in raid5d"")

Reported-by: Dan Moulding <dan@danm.net>
Closes: https://lore.kernel.org/linux-raid/20240123005700.9302-1-dan@danm.net/
Fixes: bed9e27baf52 ("Revert "md/raid5: Wait for MD_SB_CHANGE_PENDING in raid5d"")
Cc: stable@vger.kernel.org # v5.19+
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: dts: armada-3720-turris-mox: set irq type for RTC

commit fca8a117c1c9a0f8b8feed117db34cf58134dc2c upstream.

The rtc on the mox shares its interrupt line with the moxtet bus. Set
the interrupt type to be consistent between both devices. This ensures
correct setup of the interrupt line regardless of probing order.

Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Cc: <stable@vger.kernel.org> # v6.2+
Fixes: 21aad8ba615e ("arm64: dts: armada-3720-turris-mox: Add missing interrupt for RTC")
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "KEYS: encrypted: Add check for strsep"

commit 1ed4b563100230ea68821a2b25a3d9f25388a3e6 upstream.

This reverts commit b4af096b5df5dd131ab796c79cedc7069d8f4882.

New encrypted keys are created either from kernel-generated random
numbers or user-provided decrypted data.  Revert the change requiring
user-provided decrypted data.

Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

riscv: Fix wrong usage of lm_alias() when splitting a huge linear mapping

commit c29fc621e1a49949a14c7fa031dd4760087bfb29 upstream.

lm_alias() can only be used on kernel mappings since it explicitly uses
__pa_symbol(), so simply fix this by checking where the address belongs
to before.

Fixes: 311cd2f6e253 ("riscv: Fix set_memory_XX() and set_direct_map_XX() by splitting huge linear mappings")
Reported-by: syzbot+afb726d49f84c8d95ee1@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-riscv/000000000000620dd0060c02c5e1@google.com/
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Reviewed-by: Charlie Jenkins <charlie@rivosinc.com>
Link: https://lore.kernel.org/r/20231212195400.128457-1-alexghiti@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

i2c: s3c24xx: fix transferring more than one message in polling mode

[ Upstream commit 990489e1042c6c5d6bccf56deca68f8dbeed8180 ]

To properly handle ACK on the bus when transferring more than one
message in polling mode, move the polling handling loop from
s3c24xx_i2c_message_start() to s3c24xx_i2c_doxfer(). This way
i2c_s3c_irq_nextbyte() is always executed till the end, properly
acknowledging the IRQ bits and no recursive calls to
i2c_s3c_irq_nextbyte() are made.

While touching this, also fix finishing transfers in polling mode by
using common code path and always waiting for the bus to become idle
and disabled.

Fixes: 117053f77a5a ("i2c: s3c2410: Add polling mode support")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

i2c: s3c24xx: fix read transfers in polling mode

[ Upstream commit 0d9cf23ed55d7ba3ab26d617a3ae507863674c8f ]

To properly handle read transfers in polling mode, no waiting for the ACK
state is needed as it will never come. Just wait a bit to ensure start
state is on the bus and continue processing next bytes.

Fixes: 117053f77a5a ("i2c: s3c2410: Add polling mode support")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ipv6: mcast: fix data-race in ipv6_mc_down / mld_ifc_work

[ Upstream commit 2e7ef287f07c74985f1bf2858bedc62bd9ebf155 ]

idev->mc_ifc_count can be written over without proper locking.

Originally found by syzbot [1], fix this issue by encapsulating calls
to mld_ifc_stop_work() (and mld_gq_stop_work() for good measure) with
mutex_lock() and mutex_unlock() accordingly as these functions
should only be called with mc_lock per their declarations.

[1]
BUG: KCSAN: data-race in ipv6_mc_down / mld_ifc_work

write to 0xffff88813a80c832 of 1 bytes by task 3771 on cpu 0:
 mld_ifc_stop_work net/ipv6/mcast.c:1080 [inline]
 ipv6_mc_down+0x10a/0x280 net/ipv6/mcast.c:2725
 addrconf_ifdown+0xe32/0xf10 net/ipv6/addrconf.c:3949
 addrconf_notify+0x310/0x980
 notifier_call_chain kernel/notifier.c:93 [inline]
 raw_notifier_call_chain+0x6b/0x1c0 kernel/notifier.c:461
 __dev_notify_flags+0x205/0x3d0
 dev_change_flags+0xab/0xd0 net/core/dev.c:8685
 do_setlink+0x9f6/0x2430 net/core/rtnetlink.c:2916
 rtnl_group_changelink net/core/rtnetlink.c:3458 [inline]
 __rtnl_newlink net/core/rtnetlink.c:3717 [inline]
 rtnl_newlink+0xbb3/0x1670 net/core/rtnetlink.c:3754
 rtnetlink_rcv_msg+0x807/0x8c0 net/core/rtnetlink.c:6558
 netlink_rcv_skb+0x126/0x220 net/netlink/af_netlink.c:2545
 rtnetlink_rcv+0x1c/0x20 net/core/rtnetlink.c:6576
 netlink_unicast_kernel net/netlink/af_netlink.c:1342 [inline]
 netlink_unicast+0x589/0x650 net/netlink/af_netlink.c:1368
 netlink_sendmsg+0x66e/0x770 net/netlink/af_netlink.c:1910
 ...

write to 0xffff88813a80c832 of 1 bytes by task 22 on cpu 1:
 mld_ifc_work+0x54c/0x7b0 net/ipv6/mcast.c:2653
 process_one_work kernel/workqueue.c:2627 [inline]
 process_scheduled_works+0x5b8/0xa30 kernel/workqueue.c:2700
 worker_thread+0x525/0x730 kernel/workqueue.c:2781
 ...

Fixes: 2d9a93b4902b ("mld: convert from timer to delayed work")
Reported-by: syzbot+a9400cabb1d784e49abf@syzkaller.appspotmail.com
Link: https://lore.kernel.org/all/000000000000994e09060ebcdffb@google.com/
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Acked-by: Taehee Yoo <ap420073@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://lore.kernel.org/r/20240117172102.12001-1-n.zhandarovich@fintech.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests: mlxsw: qos_pfc: Adjust the test to support 8 lanes

[ Upstream commit b34f4de6d30cbaa8fed905a5080b6eace8c84dc7 ]

'qos_pfc' test checks PFC behavior. The idea is to limit the traffic
using a shaper somewhere in the flow of the packets. In this area, the
buffer is smaller than the buffer at the beginning of the flow, so it fills
up until there is no more space left. The test configures there PFC
which is supposed to notice that the headroom is filling up and send PFC
Xoff to indicate the transmitter to stop sending traffic for the priorities
sharing this PG.

The Xon/Xoff threshold is auto-configured and always equal to
2*(MTU rounded up to cell size). Even after sending the PFC Xoff packet,
traffic will keep arriving until the transmitter receives and processes
the PFC packet. This amount of traffic is known as the PFC delay allowance.

Currently the buffer for the delay traffic is configured as 100KB. The
MTU in the test is 10KB, therefore the threshold for Xoff is about 20KB.
This allows 80KB extra to be stored in this buffer.

8-lane ports use two buffers among which the configured buffer is split,
the Xoff threshold then applies to each buffer in parallel.

The test does not take into account the behavior of 8-lane ports, when the
ports are configured to 400Gbps with 8 lanes or 800Gbps with 8 lanes,
packets are dropped and the test fails.

Check if the relevant ports use 8 lanes, in such case double the size of
the buffer, as the headroom is split half-half.

Cc: Shuah Khan <shuah@kernel.org>
Fixes: bfa804784e32 ("selftests: mlxsw: Add a PFC test")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/23ff11b7dff031eb04a41c0f5254a2b636cd8ebb.1705502064.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mlxsw: spectrum_router: Register netdevice notifier before nexthop

[ Upstream commit 62bef63646c194e0f82b40304a0f2d060b28687b ]

If there are IPIP nexthops at the time when the driver is loaded (or the
devlink instance reloaded), the driver looks up the corresponding IPIP
entry. But IPIP entries are only created as a result of netdevice
notifications. Since the netdevice notifier is registered after the nexthop
notifier, mlxsw_sp_nexthop_type_init() never finds the IPIP entry,
registers the nexthop MLXSW_SP_NEXTHOP_TYPE_ETH, and fails to assign a CRIF
to the nexthop. Later on when the CRIF is necessary, the WARN_ON in
mlxsw_sp_nexthop_rif() triggers, causing the splat [1].

In order to fix the issue, reorder the netdevice notifier to be registered
before the nexthop one.

[1] (edited for clarity):

    WARNING: CPU: 1 PID: 1364 at drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:3245 mlxsw_sp_nexthop_rif (drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:3246 (discriminator 1)) mlxsw_spectrum
    Hardware name: Mellanox Technologies Ltd. MSN4410/VMOD0010, BIOS 5.11 01/06/2019
    Call Trace:
    ? mlxsw_sp_nexthop_rif (drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:3246 (discriminator 1)) mlxsw_spectrum
    __mlxsw_sp_nexthop_eth_update (drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:3637) mlxsw_spectrum
    mlxsw_sp_nexthop_update (drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:3679 drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:3727) mlxsw_spectrum
    mlxsw_sp_nexthop_group_update (drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:3757) mlxsw_spectrum
    mlxsw_sp_nexthop_group_refresh (drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:4112) mlxsw_spectrum
    mlxsw_sp_nexthop_obj_event (drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:5118 drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:5191 drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:5315 drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:5500) mlxsw_spectrum
    nexthops_dump (net/ipv4/nexthop.c:217 net/ipv4/nexthop.c:440 net/ipv4/nexthop.c:3609)
    register_nexthop_notifier (net/ipv4/nexthop.c:3624)
    mlxsw_sp_router_init (drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:11486) mlxsw_spectrum
    mlxsw_sp_init (drivers/net/ethernet/mellanox/mlxsw/spectrum.c:3267) mlxsw_spectrum
    __mlxsw_core_bus_device_register (drivers/net/ethernet/mellanox/mlxsw/core.c:2202) mlxsw_core
    mlxsw_devlink_core_bus_device_reload_up (drivers/net/ethernet/mellanox/mlxsw/core.c:2265 drivers/net/ethernet/mellanox/mlxsw/core.c:1603) mlxsw_core
    devlink_reload (net/devlink/dev.c:314 net/devlink/dev.c:475)
    [...]

Fixes: 9464a3d68ea9 ("mlxsw: spectrum_router: Track next hops at CRIFs")
Reported-by: Maksym Yaremchuk <maksymy@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/74edb8d45d004e8d8f5318eede6ccc3d786d8ba9.1705502064.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mlxsw: spectrum_acl_tcam: Fix stack corruption

[ Upstream commit 483ae90d8f976f8339cf81066312e1329f2d3706 ]

When tc filters are first added to a net device, the corresponding local
port gets bound to an ACL group in the device. The group contains a list
of ACLs. In turn, each ACL points to a different TCAM region where the
filters are stored. During forwarding, the ACLs are sequentially
evaluated until a match is found.

One reason to place filters in different regions is when they are added
with decreasing priorities and in an alternating order so that two
consecutive filters can never fit in the same region because of their
key usage.

In Spectrum-2 and newer ASICs the firmware started to report that the
maximum number of ACLs in a group is more than 16, but the layout of the
register that configures ACL groups (PAGT) was not updated to account
for that. It is therefore possible to hit stack corruption [1] in the
rare case where more than 16 ACLs in a group are required.

Fix by limiting the maximum ACL group size to the minimum between what
the firmware reports and the maximum ACLs that fit in the PAGT register.

Add a test case to make sure the machine does not crash when this
condition is hit.

[1]
Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: mlxsw_sp_acl_tcam_group_update+0x116/0x120
[...]
 dump_stack_lvl+0x36/0x50
 panic+0x305/0x330
 __stack_chk_fail+0x15/0x20
 mlxsw_sp_acl_tcam_group_update+0x116/0x120
 mlxsw_sp_acl_tcam_group_region_attach+0x69/0x110
 mlxsw_sp_acl_tcam_vchunk_get+0x492/0xa20
 mlxsw_sp_acl_tcam_ventry_add+0x25/0xe0
 mlxsw_sp_acl_rule_add+0x47/0x240
 mlxsw_sp_flower_replace+0x1a9/0x1d0
 tc_setup_cb_add+0xdc/0x1c0
 fl_hw_replace_filter+0x146/0x1f0
 fl_change+0xc17/0x1360
 tc_new_tfilter+0x472/0xb90
 rtnetlink_rcv_msg+0x313/0x3b0
 netlink_rcv_skb+0x58/0x100
 netlink_unicast+0x244/0x390
 netlink_sendmsg+0x1e4/0x440
 ____sys_sendmsg+0x164/0x260
 ___sys_sendmsg+0x9a/0xe0
 __sys_sendmsg+0x7a/0xc0
 do_syscall_64+0x40/0xe0
 entry_SYSCALL_64_after_hwframe+0x63/0x6b

Fixes: c3ab435466d5 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Reported-by: Orel Hagag <orelh@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/2d91c89afba59c22587b444994ae419dbea8d876.1705502064.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mlxsw: spectrum_acl_tcam: Fix NULL pointer dereference in error path

[ Upstream commit efeb7dfea8ee10cdec11b6b6ba4e405edbe75809 ]

When calling mlxsw_sp_acl_tcam_region_destroy() from an error path after
failing to attach the region to an ACL group, we hit a NULL pointer
dereference upon 'region->group->tcam' [1].

Fix by retrieving the 'tcam' pointer using mlxsw_sp_acl_to_tcam().

[1]
BUG: kernel NULL pointer dereference, address: 0000000000000000
[...]
RIP: 0010:mlxsw_sp_acl_tcam_region_destroy+0xa0/0xd0
[...]
Call Trace:
 mlxsw_sp_acl_tcam_vchunk_get+0x88b/0xa20
 mlxsw_sp_acl_tcam_ventry_add+0x25/0xe0
 mlxsw_sp_acl_rule_add+0x47/0x240
 mlxsw_sp_flower_replace+0x1a9/0x1d0
 tc_setup_cb_add+0xdc/0x1c0
 fl_hw_replace_filter+0x146/0x1f0
 fl_change+0xc17/0x1360
 tc_new_tfilter+0x472/0xb90
 rtnetlink_rcv_msg+0x313/0x3b0
 netlink_rcv_skb+0x58/0x100
 netlink_unicast+0x244/0x390
 netlink_sendmsg+0x1e4/0x440
 ____sys_sendmsg+0x164/0x260
 ___sys_sendmsg+0x9a/0xe0
 __sys_sendmsg+0x7a/0xc0
 do_syscall_64+0x40/0xe0
 entry_SYSCALL_64_after_hwframe+0x63/0x6b

Fixes: 22a677661f56 ("mlxsw: spectrum: Introduce ACL core with simple TCAM implementation")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/fb6a4542bbc9fcab5a523802d97059bffbca7126.1705502064.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mlxsw: spectrum_acl_erp: Fix error flow of pool allocation failure

[ Upstream commit 6d6eeabcfaba2fcadf5443b575789ea606f9de83 ]

Lately, a bug was found when many TC filters are added - at some point,
several bugs are printed to dmesg [1] and the switch is crashed with
segmentation fault.

The issue starts when gen_pool_free() fails because of unexpected
behavior - a try to free memory which is already freed, this leads to BUG()
call which crashes the switch and makes many other bugs.

Trying to track down the unexpected behavior led to a bug in eRP code. The
function mlxsw_sp_acl_erp_table_alloc() gets a pointer to the allocated
index, sets the value and returns an error code. When gen_pool_alloc()
fails it returns address 0, we track it and return -ENOBUFS outside, BUT
the call for gen_pool_alloc() already override the index in erp_table
structure. This is a problem when such allocation is done as part of
table expansion. This is not a new table, which will not be used in case
of allocation failure. We try to expand eRP table and override the
current index (non-zero) with zero. Then, it leads to an unexpected
behavior when address 0 is freed twice. Note that address 0 is valid in
erp_table->base_index and indeed other tables use it.

gen_pool_alloc() fails in case that there is no space left in the
pre-allocated pool, in our case, the pool is limited to
ACL_MAX_ERPT_BANK_SIZE, which is read from hardware. When more than max
erp entries are required, we exceed the limit and return an error, this
error leads to "Failed to migrate vregion" print.

Fix this by changing erp_table->base_index only in case of a successful
allocation.

Add a test case for such a scenario. Without this fix it causes
segmentation fault:

$ TESTS="max_erp_entries_test" ./tc_flower.sh
./tc_flower.sh: line 988:  1560 Segmentation fault      tc filter del dev $h2 ingress chain $i protocol ip pref $i handle $j flower &>/dev/null

[1]:
kernel BUG at lib/genalloc.c:508!
invalid opcode: 0000 [#1] PREEMPT SMP
CPU: 6 PID: 3531 Comm: tc Not tainted 6.7.0-rc5-custom-ga6893f479f5e #1
Hardware name: Mellanox Technologies Ltd. MSN4700/VMOD0010, BIOS 5.11 07/12/2021
RIP: 0010:gen_pool_free_owner+0xc9/0xe0
...
Call Trace:
 <TASK>
 __mlxsw_sp_acl_erp_table_other_dec+0x70/0xa0 [mlxsw_spectrum]
 mlxsw_sp_acl_erp_mask_destroy+0xf5/0x110 [mlxsw_spectrum]
 objagg_obj_root_destroy+0x18/0x80 [objagg]
 objagg_obj_destroy+0x12c/0x130 [objagg]
 mlxsw_sp_acl_erp_mask_put+0x37/0x50 [mlxsw_spectrum]
 mlxsw_sp_acl_ctcam_region_entry_remove+0x74/0xa0 [mlxsw_spectrum]
 mlxsw_sp_acl_ctcam_entry_del+0x1e/0x40 [mlxsw_spectrum]
 mlxsw_sp_acl_tcam_ventry_del+0x78/0xd0 [mlxsw_spectrum]
 mlxsw_sp_flower_destroy+0x4d/0x70 [mlxsw_spectrum]
 mlxsw_sp_flow_block_cb+0x73/0xb0 [mlxsw_spectrum]
 tc_setup_cb_destroy+0xc1/0x180
 fl_hw_destroy_filter+0x94/0xc0 [cls_flower]
 __fl_delete+0x1ac/0x1c0 [cls_flower]
 fl_destroy+0xc2/0x150 [cls_flower]
 tcf_proto_destroy+0x1a/0xa0
...
mlxsw_spectrum3 0000:07:00.0: Failed to migrate vregion
mlxsw_spectrum3 0000:07:00.0: Failed to migrate vregion

Fixes: f465261aa105 ("mlxsw: spectrum_acl: Implement common eRP core")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/4cfca254dfc0e5d283974801a24371c7b6db5989.1705502064.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

loop: fix the the direct I/O support check when used on top of block devices

[ Upstream commit baa7d536077dcdfe2b70c476a8873d1745d3de0f ]

__loop_update_dio only checks the alignment requirement for block backed
file systems, but misses them for the case where the loop device is
created directly on top of another block device.  Due to this creating
a loop device with default option plus the direct I/O flag on a > 512 byte
sector size file system will lead to incorrect I/O being submitted to the
lower block device and a lot of error from the lock layer.  This can
be seen with xfstests generic/563.

Fix the code in __loop_update_dio by factoring the alignment check into
a helper, and calling that also for the struct block_device of a block
device inode.

Also remove the TODO comment talking about dynamically switching between
buffered and direct I/O, which is a would be a recipe for horrible
performance and occasional data loss.

Fixes: 2e5ab5f379f9 ("block: loop: prepare for supporing direct IO")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20240117175901.871796-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ethtool: netlink: Add missing ethnl_ops_begin/complete

[ Upstream commit f1172f3ee3a98754d95b968968920a7d03fdebcc ]

Accessing an ethernet device that is powered off or clock gated might
cause the CPU to hang. Add ethnl_ops_begin/complete in
ethnl_set_features() to protect against this.

Fixes: 0980bfcd6954 ("ethtool: set netdev features with FEATURES_SET request")
Signed-off-by: Ludvig Pärsson <ludvig.parsson@axis.com>
Link: https://lore.kernel.org/r/20240117-etht2-v2-1-1a96b6e8c650@axis.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64/ptrace: Don't flush ZA/ZT storage when writing ZA via ptrace

[ Upstream commit b7c510d049049409e8945b932f4b0b357fa17415 ]

When writing ZA we currently unconditionally flush the buffer used to store
it as part of ensuring that it is allocated. Since this buffer is shared
with ZT0 this means that a write to ZA when PSTATE.ZA is already set will
corrupt the value of ZT0 on a SME2 system. Fix this by only flushing the
backing storage if PSTATE.ZA was not previously set.

This will mean that short or failed writes may leave stale data in the
buffer, this seems as correct as our current behaviour and unlikely to be
something that userspace will rely on.

Fixes: f90b529bcbe5 ("arm64/sme: Implement ZT0 ptrace support")
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240115-arm64-fix-ptrace-za-zt-v1-1-48617517028a@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

kdb: Fix a potential buffer overflow in kdb_local()

[ Upstream commit 4f41d30cd6dc865c3cbc1a852372321eba6d4e4c ]

When appending "[defcmd]" to 'kdb_prompt_str', the size of the string
already in the buffer should be taken into account.

An option could be to switch from strncat() to strlcat() which does the
correct test to avoid such an overflow.

However, this actually looks as dead code, because 'defcmd_in_progress'
can't be true here.
See a more detailed explanation at [1].

[1]: https://lore.kernel.org/all/CAD=FV=WSh7wKN7Yp-3wWiDgX4E3isQ8uh0LCzTmd1v9Cg9j+nQ@mail.gmail.com/

Fixes: 5d5314d6795f ("kdb: core for kgdb back end (1 of 2)")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

io_uring: adjust defer tw counting

[ Upstream commit dc12d1799ce710fd90abbe0ced71e7e1ae0894fc ]

The UINT_MAX work item counting bias in io_req_local_work_add() in case
of !IOU_F_TWQ_LAZY_WAKE works in a sense that we will not miss a wake up,
however it's still eerie. In particular, if we add a lazy work item
after a non-lazy one, we'll increment it and get nr_tw==0, and
subsequent adds may try to unnecessarily wake up the task, which is
though not so likely to happen in real workloads.

Half the bias, it's still large enough to be larger than any valid
->cq_wait_nr, which is limited by IORING_MAX_CQ_ENTRIES, but further
have a good enough of space before it overflows.

Fixes: 8751d15426a31 ("io_uring: reduce scheduling due to tw")
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/108b971e958deaf7048342930c341ba90f75d806.1705438669.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ipvs: avoid stat macros calls from preemptible context

[ Upstream commit d6938c1c76c64f42363d0d1f051e1b4641c2ad40 ]

Inside decrement_ttl() upon discovering that the packet ttl has exceeded,
__IP_INC_STATS and __IP6_INC_STATS macros can be called from preemptible
context having the following backtrace:

check_preemption_disabled: 48 callbacks suppressed
BUG: using __this_cpu_add() in preemptible [00000000] code: curl/1177
caller is decrement_ttl+0x217/0x830
CPU: 5 PID: 1177 Comm: curl Not tainted 6.7.0+ #34
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 04/01/2014
Call Trace:
 <TASK>
 dump_stack_lvl+0xbd/0xe0
 check_preemption_disabled+0xd1/0xe0
 decrement_ttl+0x217/0x830
 __ip_vs_get_out_rt+0x4e0/0x1ef0
 ip_vs_nat_xmit+0x205/0xcd0
 ip_vs_in_hook+0x9b1/0x26a0
 nf_hook_slow+0xc2/0x210
 nf_hook+0x1fb/0x770
 __ip_local_out+0x33b/0x640
 ip_local_out+0x2a/0x490
 __ip_queue_xmit+0x990/0x1d10
 __tcp_transmit_skb+0x288b/0x3d10
 tcp_connect+0x3466/0x5180
 tcp_v4_connect+0x1535/0x1bb0
 __inet_stream_connect+0x40d/0x1040
 inet_stream_connect+0x57/0xa0
 __sys_connect_file+0x162/0x1a0
 __sys_connect+0x137/0x160
 __x64_sys_connect+0x72/0xb0
 do_syscall_64+0x6f/0x140
 entry_SYSCALL_64_after_hwframe+0x6e/0x76
RIP: 0033:0x7fe6dbbc34e0

Use the corresponding preemption-aware variants: IP_INC_STATS and
IP6_INC_STATS.

Found by Linux Verification Center (linuxtesting.org).

Fixes: 8d8e20e2d7bb ("ipvs: Decrement ttl")
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Acked-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Simon Horman <horms@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: nf_tables: reject NFT_SET_CONCAT with not field length description

[ Upstream commit 113661e07460a6604aacc8ae1b23695a89e7d4b3 ]

It is still possible to set on the NFT_SET_CONCAT flag by specifying a
set size and no field description, report EINVAL in such case.

Fixes: 1b6345d4160e ("netfilter: nf_tables: check NFT_SET_CONCAT flag if field_count is specified")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: nf_tables: skip dead set elements in netlink dump

[ Upstream commit 6b1ca88e4bb63673dc9f9c7f23c899f22c3cb17a ]

Delete from packet path relies on the garbage collector to purge
elements with NFT_SET_ELEM_DEAD_BIT on.

Skip these dead elements from nf_tables_dump_setelem() path, I very
rarely see tests/shell/testcases/maps/typeof_maps_add_delete reports
[DUMP FAILED] showing a mismatch in the expected output with an element
that should not be there.

If the netlink dump happens before GC worker run, it might show dead
elements in the ruleset listing.

nft_rhash_get() already skips dead elements in nft_rhash_cmp(),
therefore, it already does not show the element when getting a single
element via netlink control plane.

Fixes: 5f68718b34a5 ("netfilter: nf_tables: GC transaction API to avoid race with control plane")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: nf_tables: do not allow mismatch field size and set key length

[ Upstream commit 3ce67e3793f48c1b9635beb9bb71116ca1e51b58 ]

The set description provides the size of each field in the set whose sum
should not mismatch the set key length, bail out otherwise.

I did not manage to crash nft_set_pipapo with mismatch fields and set key
length so far, but this is UB which must be disallowed.

Fixes: f3a2181e16f1 ("netfilter: nf_tables: Support for sets with multiple ranged fields")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: bridge: replace physindev with physinif in nf_bridge_info

[ Upstream commit 9874808878d9eed407e3977fd11fee49de1e1d86 ]

An skb can be added to a neigh->arp_queue while waiting for an arp
reply. Where original skb's skb->dev can be different to neigh's
neigh->dev. For instance in case of bridging dnated skb from one veth to
another, the skb would be added to a neigh->arp_queue of the bridge.

As skb->dev can be reset back to nf_bridge->physindev and used, and as
there is no explicit mechanism that prevents this physindev from been
freed under us (for instance neigh_flush_dev doesn't cleanup skbs from
different device's neigh queue) we can crash on e.g. this stack:

arp_process
  neigh_update
    skb = __skb_dequeue(&neigh->arp_queue)
      neigh_resolve_output(..., skb)
        ...
          br_nf_dev_xmit
            br_nf_pre_routing_finish_bridge_slow
              skb->dev = nf_bridge->physindev
              br_handle_frame_finish

Let's use plain ifindex instead of net_device link. To peek into the
original net_device we will use dev_get_by_index_rcu(). Thus either we
get device and are safe to use it or we don't get it and drop skb.

Fixes: c4e70a87d975 ("netfilter: bridge: rename br_netfilter.c to br_netfilter_hooks.c")
Suggested-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: propagate net to nf_bridge_get_physindev

[ Upstream commit a54e72197037d2c9bfcd70dddaac8c8ccb5b41ba ]

This is a preparation patch for replacing physindev with physinif on
nf_bridge_info structure. We will use dev_get_by_index_rcu to resolve
device, when needed, and it requires net to be available.

Signed-off-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Stable-dep-of: 9874808878d9 ("netfilter: bridge: replace physindev with physinif in nf_bridge_info")
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: nf_queue: remove excess nf_bridge variable

[ Upstream commit aeaa44075f8e49e2e0ad4507d925e690b7950145 ]

We don't really need nf_bridge variable here. And nf_bridge_info_exists
is better replacement for nf_bridge_info_get in case we are only
checking for existence.

Signed-off-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Stable-dep-of: 9874808878d9 ("netfilter: bridge: replace physindev with physinif in nf_bridge_info")
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: nfnetlink_log: use proper helper for fetching physinif

[ Upstream commit c3f9fd54cd87233f53bdf0e191a86b3a5e960e02 ]

We don't use physindev in __build_packet_message except for getting
physinif from it. So let's switch to nf_bridge_get_physinif to get what
we want directly.

Signed-off-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Stable-dep-of: 9874808878d9 ("netfilter: bridge: replace physindev with physinif in nf_bridge_info")
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: nft_limit: do not ignore unsupported flags

[ Upstream commit 91a139cee1202a4599a380810d93c69b5bac6197 ]

Bail out if userspace provides unsupported flags, otherwise future
extensions to the limit expression will be silently ignored by the
kernel.

Fixes: c7862a5f0de5 ("netfilter: nft_limit: allow to invert matching criteria")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: nf_tables: reject invalid set policy

[ Upstream commit 0617c3de9b4026b87be12b0cb5c35f42c7c66fcb ]

Report -EINVAL in case userspace provides a unsupported set backend
policy.

Fixes: c50b960ccc59 ("netfilter: nf_tables: implement proper set selection")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: netdevsim: don't try to destroy PHC on VFs

[ Upstream commit ea937f77208323d35ffe2f8d8fc81b00118bfcda ]

PHC gets initialized in nsim_init_netdevsim(), which
is only called if (nsim_dev_port_is_pf()).

Create a counterpart of nsim_init_netdevsim() and
move the mock_phc_destroy() there.

This fixes a crash trying to destroy netdevsim with
VFs instantiated, as caught by running the devlink.sh test:

    BUG: kernel NULL pointer dereference, address: 00000000000000b8
    RIP: 0010:mock_phc_destroy+0xd/0x30
    Call Trace:
     <TASK>
     nsim_destroy+0x4a/0x70 [netdevsim]
     __nsim_dev_port_del+0x47/0x70 [netdevsim]
     nsim_dev_reload_destroy+0x105/0x120 [netdevsim]
     nsim_drv_remove+0x2f/0xb0 [netdevsim]
     device_release_driver_internal+0x1a1/0x210
     bus_remove_device+0xd5/0x120
     device_del+0x159/0x490
     device_unregister+0x12/0x30
     del_device_store+0x11a/0x1a0 [netdevsim]
     kernfs_fop_write_iter+0x130/0x1d0
     vfs_write+0x30b/0x4b0
     ksys_write+0x69/0xf0
     do_syscall_64+0xcc/0x1e0
     entry_SYSCALL_64_after_hwframe+0x6f/0x77

Fixes: b63e78fca889 ("net: netdevsim: use mock PHC driver")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mptcp: relax check on MPC passive fallback

[ Upstream commit c0f5aec28edf98906d28f08daace6522adf9ee7a ]

While testing the blamed commit below, I was able to miss (!)
packetdrill failures in the fastopen test-cases.

On passive fastopen the child socket is created by incoming TCP MPC syn,
allow for both MPC_SYN and MPC_ACK header.

Fixes: 724b00c12957 ("mptcp: refine opt_mp_capable determination")
Reviewed-by: Matthieu Baerts <matttbe@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

LoongArch: BPF: Prevent out-of-bounds memory access

[ Upstream commit 36a87385e31c9343af9a4756598e704741250a67 ]

The test_tag test triggers an unhandled page fault:

  # ./test_tag
  [  130.640218] CPU 0 Unable to handle kernel paging request at virtual address ffff80001b898004, era == 9000000003137f7c, ra == 9000000003139e70
  [  130.640501] Oops[#3]:
  [  130.640553] CPU: 0 PID: 1326 Comm: test_tag Tainted: G      D    O       6.7.0-rc4-loong-devel-gb62ab1a397cf #47 61985c1d94084daa2432f771daa45b56b10d8d2a
  [  130.640764] Hardware name: QEMU QEMU Virtual Machine, BIOS unknown 2/2/2022
  [  130.640874] pc 9000000003137f7c ra 9000000003139e70 tp 9000000104cb4000 sp 9000000104cb7a40
  [  130.641001] a0 ffff80001b894000 a1 ffff80001b897ff8 a2 000000006ba210be a3 0000000000000000
  [  130.641128] a4 000000006ba210be a5 00000000000000f1 a6 00000000000000b3 a7 0000000000000000
  [  130.641256] t0 0000000000000000 t1 00000000000007f6 t2 0000000000000000 t3 9000000004091b70
  [  130.641387] t4 000000006ba210be t5 0000000000000004 t6 fffffffffffffff0 t7 90000000040913e0
  [  130.641512] t8 0000000000000005 u0 0000000000000dc0 s9 0000000000000009 s0 9000000104cb7ae0
  [  130.641641] s1 00000000000007f6 s2 0000000000000009 s3 0000000000000095 s4 0000000000000000
  [  130.641771] s5 ffff80001b894000 s6 ffff80001b897fb0 s7 9000000004090c50 s8 0000000000000000
  [  130.641900]    ra: 9000000003139e70 build_body+0x1fcc/0x4988
  [  130.642007]   ERA: 9000000003137f7c build_body+0xd8/0x4988
  [  130.642112]  CRMD: 000000b0 (PLV0 -IE -DA +PG DACF=CC DACM=CC -WE)
  [  130.642261]  PRMD: 00000004 (PPLV0 +PIE -PWE)
  [  130.642353]  EUEN: 00000003 (+FPE +SXE -ASXE -BTE)
  [  130.642458]  ECFG: 00071c1c (LIE=2-4,10-12 VS=7)
  [  130.642554] ESTAT: 00010000 [PIL] (IS= ECode=1 EsubCode=0)
  [  130.642658]  BADV: ffff80001b898004
  [  130.642719]  PRID: 0014c010 (Loongson-64bit, Loongson-3A5000)
  [  130.642815] Modules linked in: [last unloaded: bpf_testmod(O)]
  [  130.642924] Process test_tag (pid: 1326, threadinfo=00000000f7f4015f, task=000000006499f9fd)
  [  130.643062] Stack : 0000000000000000 9000000003380724 0000000000000000 0000000104cb7be8
  [  130.643213]         0000000000000000 25af8d9b6e600558 9000000106250ea0 9000000104cb7ae0
  [  130.643378]         0000000000000000 0000000000000000 9000000104cb7be8 90000000049f6000
  [  130.643538]         0000000000000090 9000000106250ea0 ffff80001b894000 ffff80001b894000
  [  130.643685]         00007ffffb917790 900000000313ca94 0000000000000000 0000000000000000
  [  130.643831]         ffff80001b894000 0000000000000ff7 0000000000000000 9000000100468000
  [  130.643983]         0000000000000000 0000000000000000 0000000000000040 25af8d9b6e600558
  [  130.644131]         0000000000000bb7 ffff80001b894048 0000000000000000 0000000000000000
  [  130.644276]         9000000104cb7be8 90000000049f6000 0000000000000090 9000000104cb7bdc
  [  130.644423]         ffff80001b894000 0000000000000000 00007ffffb917790 90000000032acfb0
  [  130.644572]         ...
  [  130.644629] Call Trace:
  [  130.644641] [<9000000003137f7c>] build_body+0xd8/0x4988
  [  130.644785] [<900000000313ca94>] bpf_int_jit_compile+0x228/0x4ec
  [  130.644891] [<90000000032acfb0>] bpf_prog_select_runtime+0x158/0x1b0
  [  130.645003] [<90000000032b3504>] bpf_prog_load+0x760/0xb44
  [  130.645089] [<90000000032b6744>] __sys_bpf+0xbb8/0x2588
  [  130.645175] [<90000000032b8388>] sys_bpf+0x20/0x2c
  [  130.645259] [<9000000003f6ab38>] do_syscall+0x7c/0x94
  [  130.645369] [<9000000003121c5c>] handle_syscall+0xbc/0x158
  [  130.645507]
  [  130.645539] Code: 380839f6  380831f9  28412bae <24000ca6> 004081ad  0014cb50  004083e8  02bff34c  58008e91
  [  130.645729]
  [  130.646418] ---[ end trace 0000000000000000 ]---

On my machine, which has CONFIG_PAGE_SIZE_16KB=y, the test failed at
loading a BPF prog with 2039 instructions:

  prog = (struct bpf_prog *)ffff80001b894000
  insn = (struct bpf_insn *)(prog->insnsi)ffff80001b894048
  insn + 2039 = (struct bpf_insn *)ffff80001b898000 <- end of the page

In the build_insn() function, we are trying to access next instruction
unconditionally, i.e. `(insn + 1)->imm`. The address lies in the next
page and can be not owned by the current process, thus an page fault is
inevitable and then segfault.

So, let's access next instruction only under `dst = imm64` context.

With this fix, we have:

  # ./test_tag
  test_tag: OK (40945 tests)

Fixes: bbfddb904df6f82 ("LoongArch: BPF: Avoid declare variables in switch-case")
Tested-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Hengqi Chen <hengqi.chen@gmail.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: dsa: vsc73xx: Add null pointer check to vsc73xx_gpio_probe

[ Upstream commit 776dac5a662774f07a876b650ba578d0a62d20db ]

devm_kasprintf() returns a pointer to dynamically allocated memory
which can be NULL upon failure.

Fixes: 05bd97fc559d ("net: dsa: Add Vitesse VSC73xx DSA router driver")
Signed-off-by: Kunwu Chan <chentao@kylinos.cn>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240111072018.75971-1-chentao@kylinos.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bpf: Reject variable offset alu on PTR_TO_FLOW_KEYS

[ Upstream commit 22c7fa171a02d310e3a3f6ed46a698ca8a0060ed ]

For PTR_TO_FLOW_KEYS, check_flow_keys_access() only uses fixed off
for validation. However, variable offset ptr alu is not prohibited
for this ptr kind. So the variable offset is not checked.

The following prog is accepted:

  func#0 @0
  0: R1=ctx() R10=fp0
  0: (bf) r6 = r1                       ; R1=ctx() R6_w=ctx()
  1: (79) r7 = *(u64 *)(r6 +144)        ; R6_w=ctx() R7_w=flow_keys()
  2: (b7) r8 = 1024                     ; R8_w=1024
  3: (37) r8 /= 1                       ; R8_w=scalar()
  4: (57) r8 &= 1024                    ; R8_w=scalar(smin=smin32=0,
  smax=umax=smax32=umax32=1024,var_off=(0x0; 0x400))
  5: (0f) r7 += r8
  mark_precise: frame0: last_idx 5 first_idx 0 subseq_idx -1
  mark_precise: frame0: regs=r8 stack= before 4: (57) r8 &= 1024
  mark_precise: frame0: regs=r8 stack= before 3: (37) r8 /= 1
  mark_precise: frame0: regs=r8 stack= before 2: (b7) r8 = 1024
  6: R7_w=flow_keys(smin=smin32=0,smax=umax=smax32=umax32=1024,var_off
  =(0x0; 0x400)) R8_w=scalar(smin=smin32=0,smax=umax=smax32=umax32=1024,
  var_off=(0x0; 0x400))
  6: (79) r0 = *(u64 *)(r7 +0)          ; R0_w=scalar()
  7: (95) exit

This prog loads flow_keys to r7, and adds the variable offset r8
to r7, and finally causes out-of-bounds access:

  BUG: unable to handle page fault for address: ffffc90014c80038
  [...]
  Call Trace:
   <TASK>
   bpf_dispatcher_nop_func include/linux/bpf.h:1231 [inline]
   __bpf_prog_run include/linux/filter.h:651 [inline]
   bpf_prog_run include/linux/filter.h:658 [inline]
   bpf_prog_run_pin_on_cpu include/linux/filter.h:675 [inline]
   bpf_flow_dissect+0x15f/0x350 net/core/flow_dissector.c:991
   bpf_prog_test_run_flow_dissector+0x39d/0x620 net/bpf/test_run.c:1359
   bpf_prog_test_run kernel/bpf/syscall.c:4107 [inline]
   __sys_bpf+0xf8f/0x4560 kernel/bpf/syscall.c:5475
   __do_sys_bpf kernel/bpf/syscall.c:5561 [inline]
   __se_sys_bpf kernel/bpf/syscall.c:5559 [inline]
   __x64_sys_bpf+0x73/0xb0 kernel/bpf/syscall.c:5559
   do_syscall_x64 arch/x86/entry/common.c:52 [inline]
   do_syscall_64+0x3f/0x110 arch/x86/entry/common.c:83
   entry_SYSCALL_64_after_hwframe+0x63/0x6b

Fix this by rejecting ptr alu with variable offset on flow_keys.
Applying the patch rejects the program with "R7 pointer arithmetic
on flow_keys prohibited".

Fixes: d58e468b1112 ("flow_dissector: implements flow dissector BPF hook")
Signed-off-by: Hao Sun <sunhao.th@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Link: https://lore.kernel.org/bpf/20240115082028.9992-1-sunhao.th@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: stmmac: ethtool: Fixed calltrace caused by unbalanced disable_irq_wake calls

[ Upstream commit a23aa04042187cbde16f470b49d4ad60d32e9206 ]

We found the following dmesg calltrace when testing the GMAC NIC notebook:

[9.448656] ------------[ cut here ]------------
[9.448658] Unbalanced IRQ 43 wake disable
[9.448673] WARNING: CPU: 3 PID: 1083 at kernel/irq/manage.c:688 irq_set_irq_wake+0xe0/0x128
[9.448717] CPU: 3 PID: 1083 Comm: ethtool Tainted: G           O      4.19 #1
[9.448773]         ...
[9.448774] Call Trace:
[9.448781] [<9000000000209b5c>] show_stack+0x34/0x140
[9.448788] [<9000000000d52700>] dump_stack+0x98/0xd0
[9.448794] [<9000000000228610>] __warn+0xa8/0x120
[9.448797] [<9000000000d2fb60>] report_bug+0x98/0x130
[9.448800] [<900000000020a418>] do_bp+0x248/0x2f0
[9.448805] [<90000000002035f4>] handle_bp_int+0x4c/0x78
[9.448808] [<900000000029ea40>] irq_set_irq_wake+0xe0/0x128
[9.448813] [<9000000000a96a7c>] stmmac_set_wol+0x134/0x150
[9.448819] [<9000000000be6ed0>] dev_ethtool+0x1368/0x2440
[9.448824] [<9000000000c08350>] dev_ioctl+0x1f8/0x3e0
[9.448827] [<9000000000bb2a34>] sock_ioctl+0x2a4/0x450
[9.448832] [<900000000046f044>] do_vfs_ioctl+0xa4/0x738
[9.448834] [<900000000046f778>] ksys_ioctl+0xa0/0xe8
[9.448837] [<900000000046f7d8>] sys_ioctl+0x18/0x28
[9.448840] [<9000000000211ab4>] syscall_common+0x20/0x34
[9.448842] ---[ end trace 40c18d9aec863c3e ]---

Multiple disable_irq_wake() calls will keep decreasing the IRQ
wake_depth, When wake_depth is 0, calling disable_irq_wake() again,
will report the above calltrace.

Due to the need to appear in pairs, we cannot call disable_irq_wake()
without calling enable_irq_wake(). Fix this by making sure there are
no unbalanced disable_irq_wake() calls.

Fixes: 3172d3afa998 ("stmmac: support wake up irq from external sources (v3)")
Signed-off-by: Qiang Ma <maqianga@uniontech.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240112021249.24598-1-maqianga@uniontech.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests: bonding: Change script interpreter

[ Upstream commit c2518da8e6b0e248cfff1d4b6682e14020bd4d3f ]

The tests changed by this patch, as well as the scripts they source, use
features which are not part of POSIX sh (ex. 'source' and 'local'). As a
result, these tests fail when /bin/sh is dash such as on Debian. Change the
interpreter to bash so that these tests can run successfully.

Fixes: d43eff0b85ae ("selftests: bonding: up/down delay w/ slave link flapping")
Tested-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amdgpu: fall back to INPUT power for AVG power via INFO IOCTL

[ Upstream commit d02069850fc102b07ae923535d5e212f2c8a34e9 ]

For backwards compatibility with userspace.

Fixes: 47f1724db4fe ("drm/amd: Introduce `AMDGPU_PP_SENSOR_GPU_INPUT_POWER`")
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2897
Reviewed-by: Yang Wang <kevinyang.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amdkfd: fixes for HMM mem allocation

[ Upstream commit 02eed83abc1395a1207591aafad9bcfc5cb1abcb ]

Fix err return value and reset pgmap->type after checking it.

Fixes: c83dee9b6394 ("drm/amdkfd: add SPM support for SVM")
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Dafna Hirschfeld <dhirschfeld@habana.ai>
Signed-off-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: SOF: ipc4-loader: remove the CPC check warnings

[ Upstream commit ab09fb9c629ed3aaea6a82467f08595dbc549726 ]

Warnings related to missing data in firmware manifest have
proven to be too verbose. This relates to description of
DSP module cost expressed in cycles per chunk (CPC). If
a matching value is not found in the manifest, kernel will
pass a zero value and DSP firmware will use a conservative
value in its place.

Downgrade the warnings to dev_dbg().

Fixes: d8a2c9879349 ("ASoC: SOF: ipc4-loader/topology: Query the CPC value from manifest")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://msgid.link/r/20240115092209.7184-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

gpio: mlxbf3: add an error code check in mlxbf3_gpio_probe

[ Upstream commit d460e9c2075164e9b1fa9c4c95f8c05517bd8752 ]

Clang static checker warning: Value stored to 'ret' is never read.
bgpio_init() returns error code if failed, it's better to add this
check.

Fixes: cd33f216d241 ("gpio: mlxbf3: Add gpio driver support")
Signed-off-by: Su Hui <suhui@nfschina.com>
[Bartosz: add the Fixes: tag]
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

dt-bindings: gpio: xilinx: Fix node address in gpio

[ Upstream commit 314c020c4ed3de72b15603eb6892250bc4b51702 ]

Node address doesn't match reg property which is not correct.

Fixes: ba96b2e7974b ("dt-bindings: gpio: gpio-xilinx: Convert Xilinx axi gpio binding to YAML")
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: ravb: Fix dma_addr_t truncation in error case

[ Upstream commit e327b2372bc0f18c30433ac40be07741b59231c5 ]

In ravb_start_xmit(), ravb driver uses u32 variable to store result of
dma_map_single() call. Since ravb hardware has 32-bit address fields in
descriptors, this works properly when mapping is successful - it is
platform's job to provide mapping addresses that fit into hardware
limitations.

However, in failure case dma_map_single() returns DMA_MAPPING_ERROR
constant that is 64-bit when dma_addr_t is 64-bit. Storing this constant
in u32 leads to truncation, and further call to dma_mapping_error()
fails to notice the error.

Fix that by storing result of dma_map_single() in a dma_addr_t
variable.

Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: tls, fix WARNIING in __sk_msg_free

[ Upstream commit dc9dfc8dc629e42f2234e3327b75324ffc752bc9 ]

A splice with MSG_SPLICE_PAGES will cause tls code to use the
tls_sw_sendmsg_splice path in the TLS sendmsg code to move the user
provided pages from the msg into the msg_pl. This will loop over the
msg until msg_pl is full, checked by sk_msg_full(msg_pl). The user
can also set the MORE flag to hint stack to delay sending until receiving
more pages and ideally a full buffer.

If the user adds more pages to the msg than can fit in the msg_pl
scatterlist (MAX_MSG_FRAGS) we should ignore the MORE flag and send
the buffer anyways.

What actually happens though is we abort the msg to msg_pl scatterlist
setup and then because we forget to set 'full record' indicating we
can no longer consume data without a send we fallthrough to the 'continue'
path which will check if msg_data_left(msg) has more bytes to send and
then attempts to fit them in the already full msg_pl. Then next
iteration of sender doing send will encounter a full msg_pl and throw
the warning in the syzbot report.

To fix simply check if we have a full_record in splice code path and
if not send the msg regardless of MORE flag.

Reported-and-tested-by: syzbot+f2977222e0e95cec15c8@syzkaller.appspotmail.com
Reported-by: Edward Adam Davis <eadavis@qq.com>
Fixes: fe1e81d4f73b ("tls/sw: Support MSG_SPLICE_PAGES")
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bpf: Avoid iter->offset making backward progress in bpf_iter_udp

[ Upstream commit 2242fd537fab52d5f4d2fbb1845f047c01fad0cf ]

There is a bug in the bpf_iter_udp_batch() function that stops
the userspace from making forward progress.

The case that triggers the bug is the userspace passed in
a very small read buffer. When the bpf prog does bpf_seq_printf,
the userspace read buffer is not enough to capture the whole bucket.

When the read buffer is not large enough, the kernel will remember
the offset of the bucket in iter->offset such that the next userspace
read() can continue from where it left off.

The kernel will skip the number (== "iter->offset") of sockets in
the next read(). However, the code directly decrements the
"--iter->offset". This is incorrect because the next read() may
not consume the whole bucket either and then the next-next read()
will start from offset 0. The net effect is the userspace will
keep reading from the beginning of a bucket and the process will
never finish. "iter->offset" must always go forward until the
whole bucket is consumed.

This patch fixes it by using a local variable "resume_offset"
and "resume_bucket". "iter->offset" is always reset to 0 before
it may be used. "iter->offset" will be advanced to the
"resume_offset" when it continues from the "resume_bucket" (i.e.
"state->bucket == resume_bucket"). This brings it closer to
the bpf_iter_tcp's offset handling which does not suffer
the same bug.

Cc: Aditi Ghag <aditi.ghag@isovalent.com>
Fixes: c96dac8d369f ("bpf: udp: Implement batching for sockets iterator")
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Aditi Ghag <aditi.ghag@isovalent.com>
Link: https://lore.kernel.org/r/20240112190530.3751661-3-martin.lau@linux.dev
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bpf: iter_udp: Retry with a larger batch size without going back to the previous bucket

[ Upstream commit 19ca0823f6eaad01d18f664a00550abe912c034c ]

The current logic is to use a default size 16 to batch the whole bucket.
If it is too small, it will retry with a larger batch size.

The current code accidentally does a state->bucket-- before retrying.
This goes back to retry with the previous bucket which has already
been done. This patch fixed it.

It is hard to create a selftest. I added a WARN_ON(state->bucket < 0),
forced a particular port to be hashed to the first bucket,
created >16 sockets, and observed the for-loop went back
to the "-1" bucket.

Cc: Aditi Ghag <aditi.ghag@isovalent.com>
Fixes: c96dac8d369f ("bpf: udp: Implement batching for sockets iterator")
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Aditi Ghag <aditi.ghag@isovalent.com>
Link: https://lore.kernel.org/r/20240112190530.3751661-2-martin.lau@linux.dev
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: netdev_queue: netdev_txq_completed_mb(): fix wake condition

[ Upstream commit 894d7508316e7ad722df597d68b4b1797a9eee11 ]

netif_txq_try_stop() uses "get_desc >= start_thrs" as the check for
the call to netif_tx_start_queue().

Use ">=" i netdev_txq_completed_mb(), too.

Fixes: c91c46de6bbc ("net: provide macros for commonly copied lockless queue stop/wake code")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: add more sanity check in virtio_net_hdr_to_skb()

[ Upstream commit 9181d6f8a2bb32d158de66a84164fac05e3ddd18 ]

syzbot/KMSAN reports access to uninitialized data from gso_features_check() [1]

The repro use af_packet, injecting a gso packet and hdrlen == 0.

We could fix the issue making gso_features_check() more careful
while dealing with NETIF_F_TSO_MANGLEID in fast path.

Or we can make sure virtio_net_hdr_to_skb() pulls minimal network and
transport headers as intended.

Note that for GSO packets coming from untrusted sources, SKB_GSO_DODGY
bit forces a proper header validation (and pull) before the packet can
hit any device ndo_start_xmit(), thus we do not need a precise disection
at virtio_net_hdr_to_skb() stage.

[1]
BUG: KMSAN: uninit-value in skb_gso_segment include/net/gso.h:83 [inline]
BUG: KMSAN: uninit-value in validate_xmit_skb+0x10f2/0x1930 net/core/dev.c:3629
 skb_gso_segment include/net/gso.h:83 [inline]
 validate_xmit_skb+0x10f2/0x1930 net/core/dev.c:3629
 __dev_queue_xmit+0x1eac/0x5130 net/core/dev.c:4341
 dev_queue_xmit include/linux/netdevice.h:3134 [inline]
 packet_xmit+0x9c/0x6b0 net/packet/af_packet.c:276
 packet_snd net/packet/af_packet.c:3087 [inline]
 packet_sendmsg+0x8b1d/0x9f30 net/packet/af_packet.c:3119
 sock_sendmsg_nosec net/socket.c:730 [inline]
 __sock_sendmsg net/socket.c:745 [inline]
 ____sys_sendmsg+0x9c2/0xd60 net/socket.c:2584
 ___sys_sendmsg+0x28d/0x3c0 net/socket.c:2638
 __sys_sendmsg net/socket.c:2667 [inline]
 __do_sys_sendmsg net/socket.c:2676 [inline]
 __se_sys_sendmsg net/socket.c:2674 [inline]
 __x64_sys_sendmsg+0x307/0x490 net/socket.c:2674
 do_syscall_x64 arch/x86/entry/common.c:52 [inline]
 do_syscall_64+0x44/0x110 arch/x86/entry/common.c:83
 entry_SYSCALL_64_after_hwframe+0x63/0x6b

Uninit was created at:
 slab_post_alloc_hook+0x129/0xa70 mm/slab.h:768
 slab_alloc_node mm/slub.c:3478 [inline]
 kmem_cache_alloc_node+0x5e9/0xb10 mm/slub.c:3523
 kmalloc_reserve+0x13d/0x4a0 net/core/skbuff.c:560
 __alloc_skb+0x318/0x740 net/core/skbuff.c:651
 alloc_skb include/linux/skbuff.h:1286 [inline]
 alloc_skb_with_frags+0xc8/0xbd0 net/core/skbuff.c:6334
 sock_alloc_send_pskb+0xa80/0xbf0 net/core/sock.c:2780
 packet_alloc_skb net/packet/af_packet.c:2936 [inline]
 packet_snd net/packet/af_packet.c:3030 [inline]
 packet_sendmsg+0x70e8/0x9f30 net/packet/af_packet.c:3119
 sock_sendmsg_nosec net/socket.c:730 [inline]
 __sock_sendmsg net/socket.c:745 [inline]
 ____sys_sendmsg+0x9c2/0xd60 net/socket.c:2584
 ___sys_sendmsg+0x28d/0x3c0 net/socket.c:2638
 __sys_sendmsg net/socket.c:2667 [inline]
 __do_sys_sendmsg net/socket.c:2676 [inline]
 __se_sys_sendmsg net/socket.c:2674 [inline]
 __x64_sys_sendmsg+0x307/0x490 net/socket.c:2674
 do_syscall_x64 arch/x86/entry/common.c:52 [inline]
 do_syscall_64+0x44/0x110 arch/x86/entry/common.c:83
 entry_SYSCALL_64_after_hwframe+0x63/0x6b

CPU: 0 PID: 5025 Comm: syz-executor279 Not tainted 6.7.0-rc7-syzkaller-00003-gfbafc3e621c3 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 11/17/2023

Reported-by: syzbot+7f4d0ea3df4d4fa9a65f@syzkaller.appspotmail.com
Link: https://lore.kernel.org/netdev/0000000000005abd7b060eb160cd@google.com/
Fixes: 9274124f023b ("net: stricter validation of untrusted gso packets")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

erofs: fix inconsistent per-file compression format

[ Upstream commit 118a8cf504d7dfa519562d000f423ee3ca75d2c4 ]

EROFS can select compression algorithms on a per-file basis, and each
per-file compression algorithm needs to be marked in the on-disk
superblock for initialization.

However, syzkaller can generate inconsistent crafted images that use
an unsupported algorithmtype for specific inodes, e.g. use MicroLZMA
algorithmtype even it's not set in `sbi->available_compr_algs`.  This
can lead to an unexpected "BUG: kernel NULL pointer dereference" if
the corresponding decompressor isn't built-in.

Fix this by checking against `sbi->available_compr_algs` for each
m_algorithmformat request.  Incorrect !erofs_sb_has_compr_cfgs preset
bitmap is now fixed together since it was harmless previously.

Reported-by: <bugreport@ubisectech.com>
Fixes: 8f89926290c4 ("erofs: get compression algorithms directly on mapping")
Fixes: 622ceaddb764 ("erofs: lzma compression support")
Reviewed-by: Yue Hu <huyue2@coolpad.com>
Link: https://lore.kernel.org/r/20240113150602.1471050-1-hsiangkao@linux.alibaba.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

erofs: simplify compression configuration parser

[ Upstream commit efb4fb02cef3ab410b603c8f0e1c67f61d55f542 ]

Move erofs_load_compr_cfgs() into decompressor.c as well as introduce
a callback instead of a hard-coded switch for each algorithm for
simplicity.

Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Link: https://lore.kernel.org/r/20231022130957.11398-1-xiang@kernel.org
Stable-dep-of: 118a8cf504d7 ("erofs: fix inconsistent per-file compression format")
Signed-off-by: Sasha Levin <sashal@kernel.org>

udp: annotate data-races around up->pending

[ Upstream commit 482521d8e0c6520429478aa6866cd44128b33d5d ]

up->pending can be read without holding the socket lock,
as pointed out by syzbot [1]

Add READ_ONCE() in lockless contexts, and WRITE_ONCE()
on write side.

[1]
BUG: KCSAN: data-race in udpv6_sendmsg / udpv6_sendmsg

write to 0xffff88814e5eadf0 of 4 bytes by task 15547 on cpu 1:
 udpv6_sendmsg+0x1405/0x1530 net/ipv6/udp.c:1596
 inet6_sendmsg+0x63/0x80 net/ipv6/af_inet6.c:657
 sock_sendmsg_nosec net/socket.c:730 [inline]
 __sock_sendmsg net/socket.c:745 [inline]
 __sys_sendto+0x257/0x310 net/socket.c:2192
 __do_sys_sendto net/socket.c:2204 [inline]
 __se_sys_sendto net/socket.c:2200 [inline]
 __x64_sys_sendto+0x78/0x90 net/socket.c:2200
 do_syscall_x64 arch/x86/entry/common.c:52 [inline]
 do_syscall_64+0x44/0x110 arch/x86/entry/common.c:83
 entry_SYSCALL_64_after_hwframe+0x63/0x6b

read to 0xffff88814e5eadf0 of 4 bytes by task 15551 on cpu 0:
 udpv6_sendmsg+0x22c/0x1530 net/ipv6/udp.c:1373
 inet6_sendmsg+0x63/0x80 net/ipv6/af_inet6.c:657
 sock_sendmsg_nosec net/socket.c:730 [inline]
 __sock_sendmsg net/socket.c:745 [inline]
 ____sys_sendmsg+0x37c/0x4d0 net/socket.c:2586
 ___sys_sendmsg net/socket.c:2640 [inline]
 __sys_sendmmsg+0x269/0x500 net/socket.c:2726
 __do_sys_sendmmsg net/socket.c:2755 [inline]
 __se_sys_sendmmsg net/socket.c:2752 [inline]
 __x64_sys_sendmmsg+0x57/0x60 net/socket.c:2752
 do_syscall_x64 arch/x86/entry/common.c:52 [inline]
 do_syscall_64+0x44/0x110 arch/x86/entry/common.c:83
 entry_SYSCALL_64_after_hwframe+0x63/0x6b

value changed: 0x00000000 -> 0x0000000a

Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 15551 Comm: syz-executor.1 Tainted: G        W          6.7.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 11/17/2023

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: syzbot+8d482d0e407f665d9d10@syzkaller.appspotmail.com
Link: https://lore.kernel.org/netdev/0000000000009e46c3060ebcdffd@google.com/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: stmmac: Fix ethool link settings ops for integrated PCS

[ Upstream commit 08300adac3b8dab9e2fd3be0155c7d3093c755f4 ]

Currently get/set_link_ksettings ethtool ops are dependent on PCS.
When PCS is integrated, it will not have separate link config.
Bypass configuring and checking PCS for integrated PCS.

Fixes: aa571b6275fb ("net: stmmac: add new switch to struct plat_stmmacenet_data")
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Sneh Shah <quic_snehshah@quicinc.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

block: ensure we hold a queue reference when using queue limits

[ Upstream commit 7b4f36cd22a65b750b4cb6ac14804fb7d6e6c67d ]

q_usage_counter is the only thing preventing us from the limits changing
under us in __bio_split_to_limits, but blk_mq_submit_bio doesn't hold
it while calling into it.

Move the splitting inside the region where we know we've got a queue
reference. Ideally this could still remain a shared section of code, but
let's keep the fix simple and defer any refactoring here to later.

Reported-by: Christoph Hellwig <hch@lst.de>
Fixes: 900e08075202 ("block: move queue enter logic into blk_mq_submit_bio()")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mptcp: refine opt_mp_capable determination

[ Upstream commit 724b00c12957973656d312dce2a110c75ae2c680 ]

OPTIONS_MPTCP_MPC is a combination of three flags.

It would be better to be strict about testing what
flag is expected, at least for code readability.

mptcp_parse_option() already makes the distinction.

- subflow_check_req() should use OPTION_MPTCP_MPC_SYN.

- mptcp_subflow_init_cookie_req() should use OPTION_MPTCP_MPC_ACK.

- subflow_finish_connect() should use OPTION_MPTCP_MPC_SYNACK

- subflow_syn_recv_sock should use OPTION_MPTCP_MPC_ACK

Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Fixes: 74c7dfbee3e1 ("mptcp: consolidate in_opt sub-options fields in a bitmask")
Link: https://lore.kernel.org/r/20240111194917.4044654-6-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mptcp: use OPTION_MPTCP_MPJ_SYN in subflow_check_req()

[ Upstream commit 66ff70df1a919a066942844bb095d6fcb748d78d ]

syzbot reported that subflow_check_req() was using uninitialized data in
subflow_check_req() [1]

This is because mp_opt.token is only set when OPTION_MPTCP_MPJ_SYN is also set.

While we are are it, fix mptcp_subflow_init_cookie_req()
to test for OPTION_MPTCP_MPJ_ACK.

[1]

BUG: KMSAN: uninit-value in subflow_token_join_request net/mptcp/subflow.c:91 [inline]
 BUG: KMSAN: uninit-value in subflow_check_req+0x1028/0x15d0 net/mptcp/subflow.c:209
  subflow_token_join_request net/mptcp/subflow.c:91 [inline]
  subflow_check_req+0x1028/0x15d0 net/mptcp/subflow.c:209
  subflow_v6_route_req+0x269/0x410 net/mptcp/subflow.c:367
  tcp_conn_request+0x153a/0x4240 net/ipv4/tcp_input.c:7164
 subflow_v6_conn_request+0x3ee/0x510
  tcp_rcv_state_process+0x2e1/0x4ac0 net/ipv4/tcp_input.c:6659
  tcp_v6_do_rcv+0x11bf/0x1fe0 net/ipv6/tcp_ipv6.c:1669
  tcp_v6_rcv+0x480b/0x4fb0 net/ipv6/tcp_ipv6.c:1900
  ip6_protocol_deliver_rcu+0xda6/0x2a60 net/ipv6/ip6_input.c:438
  ip6_input_finish net/ipv6/ip6_input.c:483 [inline]
  NF_HOOK include/linux/netfilter.h:314 [inline]
  ip6_input+0x15d/0x430 net/ipv6/ip6_input.c:492
  dst_input include/net/dst.h:461 [inline]
  ip6_rcv_finish+0x5db/0x870 net/ipv6/ip6_input.c:79
  NF_HOOK include/linux/netfilter.h:314 [inline]
  ipv6_rcv+0xda/0x390 net/ipv6/ip6_input.c:310
  __netif_receive_skb_one_core net/core/dev.c:5532 [inline]
  __netif_receive_skb+0x1a6/0x5a0 net/core/dev.c:5646
  netif_receive_skb_internal net/core/dev.c:5732 [inline]
  netif_receive_skb+0x58/0x660 net/core/dev.c:5791
  tun_rx_batched+0x3ee/0x980 drivers/net/tun.c:1555
  tun_get_user+0x53af/0x66d0 drivers/net/tun.c:2002
  tun_chr_write_iter+0x3af/0x5d0 drivers/net/tun.c:2048
  call_write_iter include/linux/fs.h:2020 [inline]
  new_sync_write fs/read_write.c:491 [inline]
  vfs_write+0x8ef/0x1490 fs/read_write.c:584
  ksys_write+0x20f/0x4c0 fs/read_write.c:637
  __do_sys_write fs/read_write.c:649 [inline]
  __se_sys_write fs/read_write.c:646 [inline]
  __x64_sys_write+0x93/0xd0 fs/read_write.c:646
  do_syscall_x64 arch/x86/entry/common.c:52 [inline]
  do_syscall_64+0x44/0x110 arch/x86/entry/common.c:83
 entry_SYSCALL_64_after_hwframe+0x63/0x6b

Local variable mp_opt created at:
  subflow_check_req+0x6d/0x15d0 net/mptcp/subflow.c:145
  subflow_v6_route_req+0x269/0x410 net/mptcp/subflow.c:367

CPU: 1 PID: 5924 Comm: syz-executor.3 Not tainted 6.7.0-rc8-syzkaller-00055-g5eff55d725a4 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 11/17/2023

Fixes: f296234c98a8 ("mptcp: Add handling of incoming MP_JOIN requests")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Peter Krystad <peter.krystad@linux.intel.com>
Cc: Matthieu Baerts <matttbe@kernel.org>
Cc: Mat Martineau <martineau@kernel.org>
Cc: Geliang Tang <geliang.tang@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Link: https://lore.kernel.org/r/20240111194917.4044654-5-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mptcp: use OPTION_MPTCP_MPJ_SYNACK in subflow_finish_connect()

[ Upstream commit be1d9d9d38da922bd4beeec5b6dd821ff5a1dfeb ]

subflow_finish_connect() uses four fields (backup, join_id, thmac, none)
that may contain garbage unless OPTION_MPTCP_MPJ_SYNACK has been set
in mptcp_parse_option()

Fixes: f296234c98a8 ("mptcp: Add handling of incoming MP_JOIN requests")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Peter Krystad <peter.krystad@linux.intel.com>
Cc: Matthieu Baerts <matttbe@kernel.org>
Cc: Mat Martineau <martineau@kernel.org>
Cc: Geliang Tang <geliang.tang@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Link: https://lore.kernel.org/r/20240111194917.4044654-4-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mptcp: strict validation before using mp_opt->hmac

[ Upstream commit c1665273bdc7c201766c65e561c06711f2e050dc ]

mp_opt->hmac contains uninitialized data unless OPTION_MPTCP_MPJ_ACK
was set in mptcp_parse_option().

We must refine the condition before we call subflow_hmac_valid().

Fixes: f296234c98a8 ("mptcp: Add handling of incoming MP_JOIN requests")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Peter Krystad <peter.krystad@linux.intel.com>
Cc: Matthieu Baerts <matttbe@kernel.org>
Cc: Mat Martineau <martineau@kernel.org>
Cc: Geliang Tang <geliang.tang@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Link: https://lore.kernel.org/r/20240111194917.4044654-3-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mptcp: mptcp_parse_option() fix for MPTCPOPT_MP_JOIN

[ Upstream commit 89e23277f9c16df6f9f9c1a1a07f8f132339c15c ]

mptcp_parse_option() currently sets OPTIONS_MPTCP_MPJ, for the three
possible cases handled for MPTCPOPT_MP_JOIN option.

OPTIONS_MPTCP_MPJ is the combination of three flags:
- OPTION_MPTCP_MPJ_SYN
- OPTION_MPTCP_MPJ_SYNACK
- OPTION_MPTCP_MPJ_ACK

This is a problem, because backup, join_id, token, nonce and/or hmac fields
could be left uninitialized in some cases.

Distinguish the three cases, as following patches will need this step.

Fixes: f296234c98a8 ("mptcp: Add handling of incoming MP_JOIN requests")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Peter Krystad <peter.krystad@linux.intel.com>
Cc: Matthieu Baerts <matttbe@kernel.org>
Cc: Mat Martineau <martineau@kernel.org>
Cc: Geliang Tang <geliang.tang@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Link: https://lore.kernel.org/r/20240111194917.4044654-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ALSA: hda: Properly setup HDMI stream

[ Upstream commit 454abb80e26ab85323a30e52aa7b0ee9aae1d38a ]

Since commit 4005d1ba0a7e ("ASoC: soc-dai: don't call PCM audio ops if
the stream is not supported") HDMI playback is broken with avs driver.
This happens because for HDMI stream (unlike generic HDA one)
channels_min for stream is not set when creating PCMs. Fix this by
setting the value based on first available converter.

Fixes: 4005d1ba0a7e ("ASoC: soc-dai: don't call PCM audio ops if the stream is not supported")
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20240112113349.2905328-1-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: phy: micrel: populate .soft_reset for KSZ9131

[ Upstream commit e398822c4751017fe401f57409488f5948d12fb5 ]

The RZ/G3S SMARC Module has 2 KSZ9131 PHYs. In this setup, the KSZ9131 PHY
is used with the ravb Ethernet driver. It has been discovered that when
bringing the Ethernet interface down/up continuously, e.g., with the
following sh script:

$ while :; do ifconfig eth0 down; ifconfig eth0 up; done

the link speed and duplex are wrong after interrupting the bring down/up
operation even though the Ethernet interface is up. To recover from this
state the following configuration sequence is necessary (executed
manually):

$ ifconfig eth0 down
$ ifconfig eth0 up

The behavior has been identified also on the Microchip SAMA7G5-EK board
which runs the macb driver and uses the same PHY.

The order of PHY-related operations in ravb_open() is as follows:
ravb_open() ->
  ravb_phy_start() ->
    ravb_phy_init() ->
      of_phy_connect() ->
        phy_connect_direct() ->
  phy_attach_direct() ->
    phy_init_hw() ->
      phydev->drv->soft_reset()
      phydev->drv->config_init()
      phydev->drv->config_intr()
    phy_resume()
      kszphy_resume()

The order of PHY-related operations in ravb_close is as follows:
ravb_close() ->
  phy_stop() ->
    phy_suspend() ->
      kszphy_suspend() ->
        genphy_suspend()
  // set BMCR_PDOWN bit in MII_BMCR

In genphy_suspend() setting the BMCR_PDWN bit in MII_BMCR switches the PHY
to Software Power-Down (SPD) mode (according to the KSZ9131 datasheet).
Thus, when opening the interface after it has been  previously closed (via
ravb_close()), the phydev->drv->config_init() and
phydev->drv->config_intr() reach the KSZ9131 PHY driver via the
ksz9131_config_init() and kszphy_config_intr() functions.

KSZ9131 specifies that the MII management interface remains operational
during SPD (Software Power-Down), but (according to manual):
- Only access to the standard registers (0 through 31) is supported.
- Access to MMD address spaces other than MMD address space 1 is possible
  if the spd_clock_gate_override bit is set.
- Access to MMD address space 1 is not possible.

The spd_clock_gate_override bit is not used in the KSZ9131 driver.

ksz9131_config_init() configures RGMII delay, pad skews and LEDs by
accessesing MMD registers other than those in address space 1.

The datasheet for the KSZ9131 does not specify what happens if registers
from an unsupported address space are accessed while the PHY is in SPD.

To fix the issue the .soft_reset method has been instantiated for KSZ9131,
too. This resets the PHY to the default state before doing any
configurations to it, thus switching it out of SPD.

Fixes: bff5b4b37372 ("net: phy: micrel: add Microchip KSZ9131 initial driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: micrel: Fix PTP frame parsing for lan8841

[ Upstream commit acd66c2126eb9b5da2d89ae07dbcd73b909c2111 ]

The HW has the capability to check each frame if it is a PTP frame,
which domain it is, which ptp frame type it is, different ip address in
the frame. And if one of these checks fail then the frame is not
timestamp. Most of these checks were disabled except checking the field
minorVersionPTP inside the PTP header. Meaning that once a partner sends
a frame compliant to 8021AS which has minorVersionPTP set to 1, then the
frame was not timestamp because the HW expected by default a value of 0
in minorVersionPTP.
Fix this issue by removing this check so the userspace can decide on this.

Fixes: cafc3662ee3f ("net: micrel: Add PHC support for lan8841")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Divya Koppera <divya.koppera@microchip.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

amt: do not use overwrapped cb area

[ Upstream commit bec161add35b478a7746bf58bcdea6faa19129ef ]

amt driver uses skb->cb for storing tunnel information.
This job is worked before TC layer and then amt driver load tunnel info
from skb->cb after TC layer.
So, its cb area should not be overwrapped with CB area used by TC.
In order to not use cb area used by TC, it skips the biggest cb
structure used by TC, which was qdisc_skb_cb.
But it's not anymore.
Currently, biggest structure of TC's CB is tc_skb_cb.
So, it should skip size of tc_skb_cb instead of qdisc_skb_cb.

Fixes: ec624fe740b4 ("net/sched: Extend qdisc control block with tc control block")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://lore.kernel.org/r/20240107144241.4169520-1-ap420073@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: ethernet: ti: am65-cpsw: Fix max mtu to fit ethernet frames

[ Upstream commit 64e47d8afb5ca533b27efc006405e5bcae2c4a7b ]

The value of AM65_CPSW_MAX_PACKET_SIZE represents the maximum length
of a received frame. This value is written to the register
AM65_CPSW_PORT_REG_RX_MAXLEN.

The maximum MTU configured on the network device should then leave
some room for the ethernet headers and frame check. Otherwise, if
the network interface is configured to its maximum mtu possible,
the frames will be larger than AM65_CPSW_MAX_PACKET_SIZE and will
get dropped as oversized.

The switch supports ethernet frame sizes between 64 and 2024 bytes
(including VLAN) as stated in the technical reference manual, so
define AM65_CPSW_MAX_PACKET_SIZE with that maximum size.

Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Jorge Sanjuan Garcia <jorge.sanjuangarcia@duagon.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20240105085530.14070-2-jorge.sanjuangarcia@duagon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

octeontx2-af: CN10KB: Fix FIFO length calculation for RPM2

[ Upstream commit a0cb76a770083a22167659e64ba69af6425b1d9b ]

RPM0 and RPM1 on the CN10KB SoC have 8 LMACs each, whereas RPM2
has only 4 LMACs. Similarly, the RPM0 and RPM1 have 256KB FIFO,
whereas RPM2 has 128KB FIFO. This patch fixes an issue with
improper TX credit programming for the RPM2 link.

Fixes: b9d0fedc6234 ("octeontx2-af: cn10kb: Add RPM_USX MAC support")
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240108073036.8766-1-naveenm@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

rxrpc: Fix use of Don't Fragment flag

[ Upstream commit 8722014311e613244f33952354956a82fa4b0472 ]

rxrpc normally has the Don't Fragment flag set on the UDP packets it
transmits, except when it has decided that DATA packets aren't getting
through - in which case it turns it off just for the DATA transmissions.
This can be a problem, however, for RESPONSE packets that convey
authentication and crypto data from the client to the server as ticket may
be larger than can fit in the MTU.

In such a case, rxrpc gets itself into an infinite loop as the sendmsg
returns an error (EMSGSIZE), which causes rxkad_send_response() to return
-EAGAIN - and the CHALLENGE packet is put back on the Rx queue to retry,
leading to the I/O thread endlessly attempting to perform the transmission.

Fix this by disabling DF on RESPONSE packets for now.  The use of DF and
best data MTU determination needs reconsidering at some point in the
future.

Fixes: 17926a79320a ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both")
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-afs@lists.infradead.org
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/1581852.1704813048@warthog.procyon.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: qualcomm: rmnet: fix global oob in rmnet_policy

[ Upstream commit b33fb5b801c6db408b774a68e7c8722796b59ecc ]

The variable rmnet_link_ops assign a *bigger* maxtype which leads to a
global out-of-bounds read when parsing the netlink attributes. See bug
trace below:

==================================================================
BUG: KASAN: global-out-of-bounds in validate_nla lib/nlattr.c:386 [inline]
BUG: KASAN: global-out-of-bounds in __nla_validate_parse+0x24af/0x2750 lib/nlattr.c:600
Read of size 1 at addr ffffffff92c438d0 by task syz-executor.6/84207

CPU: 0 PID: 84207 Comm: syz-executor.6 Tainted: G                 N 6.1.0 #3
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
Call Trace:
 <TASK>
 __dump_stack lib/dump_stack.c:88 [inline]
 dump_stack_lvl+0x8b/0xb3 lib/dump_stack.c:106
 print_address_description mm/kasan/report.c:284 [inline]
 print_report+0x172/0x475 mm/kasan/report.c:395
 kasan_report+0xbb/0x1c0 mm/kasan/report.c:495
 validate_nla lib/nlattr.c:386 [inline]
 __nla_validate_parse+0x24af/0x2750 lib/nlattr.c:600
 __nla_parse+0x3e/0x50 lib/nlattr.c:697
 nla_parse_nested_deprecated include/net/netlink.h:1248 [inline]
 __rtnl_newlink+0x50a/0x1880 net/core/rtnetlink.c:3485
 rtnl_newlink+0x64/0xa0 net/core/rtnetlink.c:3594
 rtnetlink_rcv_msg+0x43c/0xd70 net/core/rtnetlink.c:6091
 netlink_rcv_skb+0x14f/0x410 net/netlink/af_netlink.c:2540
 netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
 netlink_unicast+0x54e/0x800 net/netlink/af_netlink.c:1345
 netlink_sendmsg+0x930/0xe50 net/netlink/af_netlink.c:1921
 sock_sendmsg_nosec net/socket.c:714 [inline]
 sock_sendmsg+0x154/0x190 net/socket.c:734
 ____sys_sendmsg+0x6df/0x840 net/socket.c:2482
 ___sys_sendmsg+0x110/0x1b0 net/socket.c:2536
 __sys_sendmsg+0xf3/0x1c0 net/socket.c:2565
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x3b/0x90 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x63/0xcd
RIP: 0033:0x7fdcf2072359
Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 f1 19 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007fdcf13e3168 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007fdcf219ff80 RCX: 00007fdcf2072359
RDX: 0000000000000000 RSI: 0000000020000200 RDI: 0000000000000003
RBP: 00007fdcf20bd493 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 00007fffbb8d7bdf R14: 00007fdcf13e3300 R15: 0000000000022000
 </TASK>

The buggy address belongs to the variable:
 rmnet_policy+0x30/0xe0

The buggy address belongs to the physical page:
page:0000000065bdeb3c refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x155243
flags: 0x200000000001000(reserved|node=0|zone=2)
raw: 0200000000001000 ffffea00055490c8 ffffea00055490c8 0000000000000000
raw: 0000000000000000 0000000000000000 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected

Memory state around the buggy address:
 ffffffff92c43780: f9 f9 f9 f9 00 00 00 02 f9 f9 f9 f9 00 00 00 07
 ffffffff92c43800: f9 f9 f9 f9 00 00 00 05 f9 f9 f9 f9 06 f9 f9 f9
>ffffffff92c43880: f9 f9 f9 f9 00 00 00 00 00 00 f9 f9 f9 f9 f9 f9
                                                 ^
 ffffffff92c43900: 00 00 00 00 00 00 00 00 07 f9 f9 f9 f9 f9 f9 f9
 ffffffff92c43980: 00 00 00 07 f9 f9 f9 f9 00 00 00 05 f9 f9 f9 f9

According to the comment of `nla_parse_nested_deprecated`, the maxtype
should be len(destination array) - 1. Hence use `IFLA_RMNET_MAX` here.

Fixes: 14452ca3b5ce ("net: qualcomm: rmnet: Export mux_id and flags to netlink")
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Reviewed-by: Subash Abhinov Kasiviswanathan <quic_subashab@quicinc.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20240110061400.3356108-1-linma@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

s390/pci: fix max size calculation in zpci_memcpy_toio()

[ Upstream commit 80df7d6af7f6d229b34cf237b2cc9024c07111cd ]

The zpci_get_max_write_size() helper is used to determine the maximum
size a PCI store or load can use at a given __iomem address.

For the PCI block store the following restrictions apply:

1. The dst + len must not cross a 4K boundary in the (pseudo-)MMIO space
2. len must not exceed ZPCI_MAX_WRITE_SIZE
3. len must be a multiple of 8 bytes
4. The src address must be double word (8 byte) aligned
5. The dst address must be double word (8 byte) aligned

Otherwise only a normal PCI store which takes its src value from
a register can be used. For these PCI store restriction 1 still applies.
Similarly 1 also applies to PCI loads.

It turns out zpci_max_write_size() instead implements stricter
conditions which prevents PCI block stores from being used where they
can and should be used. In particular instead of conditions 4 and 5 it
wrongly enforces both dst and src to be size aligned. This indirectly
covers condition 1 but also prevents many legal PCI block stores.

On top of the functional shortcomings the zpci_get_max_write_size() is
misnamed as it is used for both read and write size calculations. Rename
it to zpci_get_max_io_size() and implement the listed conditions
explicitly.

Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Fixes: cd24834130ac ("s390/pci: base support")
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
[agordeev@linux.ibm.com replaced spaces with tabs]
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: mediatek: sof-common: Add NULL check for normal_link string

[ Upstream commit e3b3ec967a7d93b9010a5af9a2394c8b5c8f31ed ]

It's not granted that all entries of struct sof_conn_stream declare
a `normal_link` (a non-SOF, direct link) string, and this is the case
for SoCs that support only SOF paths (hence do not support both direct
and SOF usecases).

For example, in the case of MT8188 there is no normal_link string in
any of the sof_conn_stream entries and there will be more drivers
doing that in the future.

To avoid possible NULL pointer KPs, add a NULL check for `normal_link`.

Fixes: 0caf1120c583 ("ASoC: mediatek: mt8195: extract SOF common code")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://msgid.link/r/20240111105226.117603-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: mediatek-gen3: Fix translation window size calculation

[ Upstream commit 9ccc1318cf4bd90601f221268e42c3374703d681 ]

When using the fls() helper, the translation table should be a power of
two; otherwise, the resulting value will not be correct.

For example, given fls(0x3e00000) - 1 = 25, the PCIe translation window
size will be set to 0x2000000 instead of the expected size 0x3e00000.

Fix the translation window by splitting the MMIO space into multiple tables
if its size is not a power of two.

[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20231023081423.18559-1-jianjun.wang@mediatek.com
Fixes: d3bf75b579b9 ("PCI: mediatek-gen3: Add MediaTek Gen3 driver for MT8192")
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: keystone: Fix race condition when initializing PHYs

[ Upstream commit c12ca110c613a81cb0f0099019c839d078cd0f38 ]

The PCI driver invokes the PHY APIs using the ks_pcie_enable_phy()
function. The PHY in this case is the Serdes. It is possible that the
PCI instance is configured for two lane operation across two different
Serdes instances, using one lane of each Serdes.

In such a configuration, if the reference clock for one Serdes is
provided by the other Serdes, it results in a race condition. After the
Serdes providing the reference clock is initialized by the PCI driver by
invoking its PHY APIs, it is not guaranteed that this Serdes remains
powered on long enough for the PHY APIs based initialization of the
dependent Serdes. In such cases, the PLL of the dependent Serdes fails
to lock due to the absence of the reference clock from the former Serdes
which has been powered off by the PM Core.

Fix this by obtaining reference to the PHYs before invoking the PHY
initialization APIs and releasing reference after the initialization is
complete.

Link: https://lore.kernel.org/linux-pci/20230927041845.1222080-1-s-vadapalli@ti.com
Fixes: 49229238ab47 ("PCI: keystone: Cleanup PHY handling")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nvmet-tcp: Fix the H2C expected PDU len calculation

[ Upstream commit 9a1abc24850eb759e36a2f8869161c3b7254c904 ]

The nvmet_tcp_handle_h2c_data_pdu() function should take into
consideration the possibility that the header digest and/or the data
digests are enabled when calculating the expected PDU length, before
comparing it to the value stored in cmd->pdu_len.

Fixes: efa56305908b ("nvmet-tcp: Fix a kernel panic when host sends an invalid H2C PDU length")
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nvme: trace: avoid memcpy overflow warning

[ Upstream commit a7de1dea76cd6a3707707af4ea2f8bc3cdeaeb11 ]

A previous patch introduced a struct_group() in nvme_common_command to help
stringop fortification figure out the length of the fields, but one function
is not currently using them:

In file included from drivers/nvme/target/core.c:7:
In file included from include/linux/string.h:254:
include/linux/fortify-string.h:592:4: error: call to '__read_overflow2_field' declared with 'warning' attribute: detected read beyond size of field (2nd parameter); maybe use struct_group()? [-Werror,-Wattribute-warning]
                        __read_overflow2_field(q_size_field, size);
                        ^

Change this one to use the correct field name to avoid the warning.

Fixes: 5c629dc9609dc ("nvme: use struct group for generic command dwords")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nvmet: re-fix tracing strncpy() warning

[ Upstream commit 4ee7ffeb4ce50c80bc4504db6f39b25a2df6bcf4 ]

An earlier patch had tried to address a warning about a string copy with
missing zero termination:

drivers/nvme/target/trace.h:52:3: warning: ‘strncpy’ specified bound 32 equals destination size [-Wstringop-truncation]

The new version causes a different warning with some compiler versions, notably
gcc-9 and gcc-10, and also misses the zero padding that was apparently done
intentionally in the original code:

drivers/nvme/target/trace.h:56:2: error: 'strncpy' specified bound depends on the length of the source argument [-Werror=stringop-overflow=]

Change it to use strscpy_pad() with the original length, which will give
a properly padded and zero-terminated string as well as avoiding the warning.

Fixes: d86481e924a7 ("nvmet: use min of device_path and disk len")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

hisi_acc_vfio_pci: Update migration data pointer correctly on saving/resume

[ Upstream commit be12ad45e15b5ee0e2526a50266ba1d295d26a88 ]

When the optional PRE_COPY support was added to speed up the device
compatibility check, it failed to update the saving/resuming data
pointers based on the fd offset. This results in migration data
corruption and when the device gets started on the destination the
following error is reported in some cases,

[  478.907684] arm-smmu-v3 arm-smmu-v3.2.auto: event 0x10 received:
[  478.913691] arm-smmu-v3 arm-smmu-v3.2.auto:  0x0000310200000010
[  478.919603] arm-smmu-v3 arm-smmu-v3.2.auto:  0x000002088000007f
[  478.925515] arm-smmu-v3 arm-smmu-v3.2.auto:  0x0000000000000000
[  478.931425] arm-smmu-v3 arm-smmu-v3.2.auto:  0x0000000000000000
[  478.947552] hisi_zip 0000:31:00.0: qm_axi_rresp [error status=0x1] found
[  478.955930] hisi_zip 0000:31:00.0: qm_db_timeout [error status=0x400] found
[  478.955944] hisi_zip 0000:31:00.0: qm sq doorbell timeout in function 2

Fixes: d9a871e4a143 ("hisi_acc_vfio_pci: Introduce support for PRE_COPY state transitions")
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/20231120091406.780-1-shameerali.kolothum.thodi@huawei.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

spi: coldfire-qspi: Remove an erroneous clk_disable_unprepare() from the remove function

[ Upstream commit 17dc11a02d8dacc7e78968daa2a8c16281eb7d1e ]

The commit in Fixes has changed a devm_clk_get()/clk_prepare_enable() into
a devm_clk_get_enabled().
It has updated the error handling path of the probe accordingly, but the
remove has been left unchanged.

Remove now the redundant clk_disable_unprepare() call from the remove
function.

Fixes: a90a987ebe00 ("spi: use devm_clk_get_enabled() in mcfqspi_probe()")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://msgid.link/r/6670aed303e1f7680e0911387606a8ae069e2cef.1704464447.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

cxl/port: Fix missing target list lock

[ Upstream commit 5459e186a5c9f412334321cff58d70dcb0e48a04 ]

cxl_port_setup_targets() modifies the ->targets[] array of a switch
decoder. target_list_show() expects to be able to emit a coherent
snapshot of that array by "holding" ->target_lock for read. The
target_lock is held for write during initialization of the ->targets[]
array, but it is not held for write during cxl_port_setup_targets().

The ->target_lock() predates the introduction of @cxl_region_rwsem. That
semaphore protects changes to host-physical-address (HPA) decode which
is precisely what writes to a switch decoder's target list affects.

Replace ->target_lock with @cxl_region_rwsem.

Now the side-effect of snapshotting a unstable view of a decoder's
target list is likely benign so the Fixes: tag is presumptive.

Fixes: 27b3f8d13830 ("cxl/region: Program target lists")
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf db-export: Fix missing reference count get in call_path_from_sample()

[ Upstream commit 1e24ce402c97dc3c0ab050593f1d5f6fde524564 ]

The addr_location map and maps fields in the inner loop were missing
calls to map__get()/maps__get(). The subsequent addr_location__exit()
call in each loop puts the map/maps fields causing use-after-free
aborts.

This issue reproduces on at least arm64 and x86_64 with something
simple like `perf record -g ls` followed by `perf script -s script.py`
with the following script:

    perf_db_export_mode = True
    perf_db_export_calls = False
    perf_db_export_callchains = True

    def sample_table(*args):
        print(f'sample_table({args})')

    def call_path_table(*args):
        print(f'call_path_table({args}')

Committer testing:

This test, just introduced by Ian Rogers, now passes, not segfaulting
anymore:

  # perf test "perf script tests"
   95: perf script tests                                               : Ok
  #

Fixes: 0dd5041c9a0eaf8c ("perf addr_location: Add init/exit/copy functions")
Signed-off-by: Ben Gainey <ben.gainey@arm.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Tested-by: Ian Rogers <irogers@google.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20231207140911.3240408-1-ben.gainey@arm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

serial: apbuart: fix console prompt on qemu

[ Upstream commit c6dcd8050fb7c2efec6946ae9c49bc186b0a7475 ]

When using a leon kernel with qemu there where no console prompt.
The root cause is the handling of the fifo size in the tx part of the
apbuart driver.

The qemu uart driver only have a very rudimentary status handling and do
not report the number of chars queued in the tx fifo in the status register.
So the driver ends up with a fifo size of 1.

In the tx path the fifo size is divided by 2 - resulting in a fifo
size of zero.

The original implementation would always try to send one char, but
after the introduction of uart_port_tx_limited() the fifo size is
respected even for the first char.

There seems to be no good reason to divide the fifo size with two - so
remove this. It looks like something copied from the original amba driver.

With qemu we now have a minimum fifo size of one char, so we show
the prompt.

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Fixes: d11cc8c3c4b6 ("tty: serial: use uart_port_tx_limited()")
Cc: Andreas Larsson <andreas@gaisler.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: <linux-serial@vger.kernel.org>
Cc: <sparclinux@vger.kernel.org>
Link: https://lore.kernel.org/r/20231226121607.GA2622970@ravnborg.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

serial: imx: Correct clock error message in function probe()

[ Upstream commit 3e189470cad27d41a3a9dc02649f965b7ed1c90f ]

Correct the clock error message by changing the clock name.

Fixes: 1e512d45332b ("serial: imx: add error messages when .probe fails")
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231224093209.2612-1-cniedermaier@dh-electronics.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: xhci-mtk: fix a short packet issue of gen1 isoc-in transfer

[ Upstream commit 017dbfc05c31284150819890b4cc86a699cbdb71 ]

For Gen1 isoc-in transfer, host still send out unexpected ACK after device
finish the burst with a short packet, this will cause an exception on the
connected device, such as, a usb 4k camera.
It can be fixed by setting rxfifo depth less than 4k bytes, prefer to use
3k here, the side-effect is that may cause performance drop about 10%,
including bulk transfer.

Fixes: 926d60ae64a6 ("usb: xhci-mtk: modify the SOF/ITP interval for mt8195")
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20240104061640.7335-2-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

apparmor: avoid crash when parsed profile name is empty

[ Upstream commit 55a8210c9e7d21ff2644809699765796d4bfb200 ]

When processing a packed profile in unpack_profile() described like

 "profile :ns::samba-dcerpcd /usr/lib*/samba/{,samba/}samba-dcerpcd {...}"

a string ":samba-dcerpcd" is unpacked as a fully-qualified name and then
passed to aa_splitn_fqname().

aa_splitn_fqname() treats ":samba-dcerpcd" as only containing a namespace.
Thus it returns NULL for tmpname, meanwhile tmpns is non-NULL. Later
aa_alloc_profile() crashes as the new profile name is NULL now.

general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] PREEMPT SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
CPU: 6 PID: 1657 Comm: apparmor_parser Not tainted 6.7.0-rc2-dirty #16
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.2-3-gd478f380-rebuilt.opensuse.org 04/01/2014
RIP: 0010:strlen+0x1e/0xa0
Call Trace:
 <TASK>
 ? strlen+0x1e/0xa0
 aa_policy_init+0x1bb/0x230
 aa_alloc_profile+0xb1/0x480
 unpack_profile+0x3bc/0x4960
 aa_unpack+0x309/0x15e0
 aa_replace_profiles+0x213/0x33c0
 policy_update+0x261/0x370
 profile_replace+0x20e/0x2a0
 vfs_write+0x2af/0xe00
 ksys_write+0x126/0x250
 do_syscall_64+0x46/0xf0
 entry_SYSCALL_64_after_hwframe+0x6e/0x76
 </TASK>
---[ end trace 0000000000000000 ]---
RIP: 0010:strlen+0x1e/0xa0

It seems such behaviour of aa_splitn_fqname() is expected and checked in
other places where it is called (e.g. aa_remove_profiles). Well, there
is an explicit comment "a ns name without a following profile is allowed"
inside.

AFAICS, nothing can prevent unpacked "name" to be in form like
":samba-dcerpcd" - it is passed from userspace.

Deny the whole profile set replacement in such case and inform user with
EPROTO and an explaining message.

Found by Linux Verification Center (linuxtesting.org).

Fixes: 04dc715e24d0 ("apparmor: audit policy ns specified in policy load")
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

apparmor: fix possible memory leak in unpack_trans_table

[ Upstream commit 1342ad786073e96fa813ad943c19f586157ae297 ]

If we fail to unpack the transition table then the table elements which
have been already allocated are not freed on error path.

unreferenced object 0xffff88802539e000 (size 128):
  comm "apparmor_parser", pid 903, jiffies 4294914938 (age 35.085s)
  hex dump (first 32 bytes):
    20 73 6f 6d 65 20 6e 61 73 74 79 20 73 74 72 69   some nasty stri
    6e 67 20 73 6f 6d 65 20 6e 61 73 74 79 20 73 74  ng some nasty st
  backtrace:
    [<ffffffff81ddb312>] __kmem_cache_alloc_node+0x1e2/0x2d0
    [<ffffffff81c47194>] __kmalloc_node_track_caller+0x54/0x170
    [<ffffffff81c225b9>] kmemdup+0x29/0x60
    [<ffffffff83e1ee65>] aa_unpack_strdup+0xe5/0x1b0
    [<ffffffff83e20808>] unpack_pdb+0xeb8/0x2700
    [<ffffffff83e23567>] unpack_profile+0x1507/0x4a30
    [<ffffffff83e27bfa>] aa_unpack+0x36a/0x1560
    [<ffffffff83e194c3>] aa_replace_profiles+0x213/0x33c0
    [<ffffffff83de9461>] policy_update+0x261/0x370
    [<ffffffff83de978e>] profile_replace+0x20e/0x2a0
    [<ffffffff81eac8bf>] vfs_write+0x2af/0xe00
    [<ffffffff81eaddd6>] ksys_write+0x126/0x250
    [<ffffffff88f34fb6>] do_syscall_64+0x46/0xf0
    [<ffffffff890000ea>] entry_SYSCALL_64_after_hwframe+0x6e/0x76

Call aa_free_str_table() on error path as was done before the blamed
commit. It implements all necessary checks, frees str_table if it is
available and nullifies the pointers.

Found by Linux Verification Center (linuxtesting.org).

Fixes: a0792e2ceddc ("apparmor: make transition table unpack generic so it can be reused")
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

cxl/region: fix x9 interleave typo

[ Upstream commit c7ad3dc3649730af483ee1e78be5d0362da25bfe ]

CXL supports x3, x6 and x12 - not x9.

Fixes: 80d10a6cee050 ("cxl/region: Add interleave geometry attributes")
Signed-off-by: Jim Harris <jim.harris@samsung.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Link: https://lore.kernel.org/r/169904271254.204936.8580772404462743630.stgit@ubuntu
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf stat: Fix hard coded LL miss units

[ Upstream commit f2567e12a090f0eb22553a4468d4c4fe04aad906 ]

Copy-paste error where LL cache misses are reported as l1i.

Fixes: 0a57b910807ad163 ("perf stat: Use counts rather than saved_value")
Suggested-by: Guillaume Endignoux <guillaumee@google.com>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: John Garry <john.g.garry@oracle.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20231211181242.1721059-1-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf env: Avoid recursively taking env->bpf_progs.lock

[ Upstream commit 9c51f8788b5d4e9f46afbcf563255cfd355690b3 ]

Add variants of perf_env__insert_bpf_prog_info(), perf_env__insert_btf()
and perf_env__find_btf prefixed with __ to indicate the
env->bpf_progs.lock is assumed held.

Call these variants when the lock is held to avoid recursively taking it
and potentially having a thread deadlock with itself.

Fixes: f8dfeae009effc0b ("perf bpf: Show more BPF program info in print_bpf_prog_info()")
Signed-off-by: Ian Rogers <irogers@google.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Song Liu <song@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: K Prateek Nayak <kprateek.nayak@amd.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ming Wang <wangming01@loongson.cn>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ravi Bangoria <ravi.bangoria@amd.com>
Link: https://lore.kernel.org/r/20231207014655.1252484-1-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nvmet-tcp: fix a crash in nvmet_req_complete()

[ Upstream commit 0849a5441358cef02586fb2d60f707c0db195628 ]

in nvmet_tcp_handle_h2c_data_pdu(), if the host sends a data_offset
different from rbytes_done, the driver ends up calling nvmet_req_complete()
passing a status error.
The problem is that at this point cmd->req is not yet initialized,
the kernel will crash after dereferencing a NULL pointer.

Fix the bug by replacing the call to nvmet_req_complete() with
nvmet_tcp_fatal_error().

Fixes: 872d26a391da ("nvmet-tcp: add NVMe over TCP target driver")
Reviewed-by: Keith Busch <kbsuch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nvmet-tcp: Fix a kernel panic when host sends an invalid H2C PDU length

[ Upstream commit efa56305908ba20de2104f1b8508c6a7401833be ]

If the host sends an H2CData command with an invalid DATAL,
the kernel may crash in nvmet_tcp_build_pdu_iovec().

Unable to handle kernel NULL pointer dereference at
virtual address 0000000000000000
lr : nvmet_tcp_io_work+0x6ac/0x718 [nvmet_tcp]
Call trace:
  process_one_work+0x174/0x3c8
  worker_thread+0x2d0/0x3e8
  kthread+0x104/0x110

Fix the bug by raising a fatal error if DATAL isn't coherent
with the packet size.
Also, the PDU length should never exceed the MAXH2CDATA parameter which
has been communicated to the host in nvmet_tcp_handle_icreq().

Fixes: 872d26a391da ("nvmet-tcp: add NVMe over TCP target driver")
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

apparmor: Fix ref count leak in task_kill

[ Upstream commit 2cb54a19ac7153b9a26a72098c495187f64c2276 ]

apparmor_task_kill was not putting the task_cred reference tc, or the
cred_label reference tc when dealing with a passed in cred, fix this
by using a single fn exit.

Fixes: 90c436a64a6e ("apparmor: pass cred through to audit info.")
Signed-off-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

vdpa: Fix an error handling path in eni_vdpa_probe()

[ Upstream commit c1b9f2c66eed3261db76cccd8a22a9affae8dcbf ]

After a successful vp_legacy_probe() call, vp_legacy_remove() should be
called in the error handling path, as already done in the remove function.

Add the missing call.

Fixes: e85087beedca ("eni_vdpa: add vDPA driver for Alibaba ENI")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Message-Id: <a7b0ef1eabd081f1c7c894e9b11de01678e85dee.1666293559.git.christophe.jaillet@wanadoo.fr>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

power: supply: Fix null pointer dereference in smb2_probe

[ Upstream commit 88f04bc3e737155e13caddf0ba8ed19db87f0212 ]

devm_kasprintf and devm_kzalloc return a pointer to dynamically
allocated memory which can be NULL upon failure.

Fixes: 8648aeb5d7b7 ("power: supply: add Qualcomm PMI8998 SMB2 Charger driver")
Signed-off-by: Kunwu Chan <chentao@kylinos.cn>
Link: https://lore.kernel.org/r/20231124075021.1335289-1-chentao@kylinos.cn
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iommu: Don't reserve 0-length IOVA region

[ Upstream commit bb57f6705960bebeb832142ce9abf43220c3eab1 ]

When the bootloader/firmware doesn't setup the framebuffers, their
address and size are 0 in "iommu-addresses" property. If IOVA region is
reserved with 0 length, then it ends up corrupting the IOVA rbtree with
an entry which has pfn_hi < pfn_lo.
If we intend to use display driver in kernel without framebuffer then
it's causing the display IOMMU mappings to fail as entire valid IOVA
space is reserved when address and length are passed as 0.
An ideal solution would be firmware removing the "iommu-addresses"
property and corresponding "memory-region" if display is not present.
But the kernel should be able to handle this by checking for size of
IOVA region and skipping the IOVA reservation if size is 0. Also, add
a warning if firmware is requesting 0-length IOVA region reservation.

Fixes: a5bf3cfce8cb ("iommu: Implement of_iommu_get_resv_regions()")
Signed-off-by: Ashish Mhetre <amhetre@nvidia.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20231205065656.9544-1-amhetre@nvidia.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: gadget: webcam: Make g_webcam loadable again

[ Upstream commit f1fd91a0924b6bff91ca1287461fb8e3b3b61d92 ]

commit 588b9e85609b ("usb: gadget: uvc: add v4l2 enumeration api calls")
has rendered the precomposed (aka legacy) webcam gadget unloadable.

uvc_alloc() since then has depended on certain config groups being
available in configfs tree related to the UVC function. However, legacy
gadgets do not create anything in configfs, so uvc_alloc() must fail
with -ENOENT no matter what.

This patch mimics the required configfs hierarchy to satisfy the code which
inspects formats and frames found in uvcg_streaming_header.

This has been tested with guvcview on the host side, using vivid as a
source of video stream on the device side and using the userspace program
found at https://gitlab.freedesktop.org/camera/uvc-gadget.git.

Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Fixes: 588b9e85609b ("usb: gadget: uvc: add v4l2 enumeration api calls")
Link: https://lore.kernel.org/r/20231215131614.29132-1-andrzej.p@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

spmi: mtk-pmif: Serialize PMIF status check and command submission

[ Upstream commit f200fff8d019f2754f91f5d715652e3e3fdf3604 ]

Before writing the read or write command to the SPMI arbiter through the
PMIF interface, the current status of the channel is checked to ensure
it is idle. However, since the status only changes from idle when the
command is written, it is possible for two concurrent calls to determine
that the channel is idle and simultaneously send their commands. At this
point the PMIF interface hangs, with the status register no longer being
updated, and thus causing all subsequent operations to time out.

This was observed on the mt8195-cherry-tomato-r2 machine, particularly
after commit 46600ab142f8 ("regulator: Set PROBE_PREFER_ASYNCHRONOUS for
drivers between 5.10 and 5.15") was applied, since then the two MT6315
devices present on the SPMI bus would probe assynchronously and
sometimes (during probe or at a later point) read the bus
simultaneously, breaking the PMIF interface and consequently slowing
down the whole system.

To fix the issue at its root cause, introduce locking around the channel
status check and the command write, so that both become an atomic
operation, preventing race conditions between two (or more) SPMI bus
read/write operations. A spinlock is used since this is a fast bus, as
indicated by the usage of the atomic variant of readl_poll, and
'.fast_io = true' being used in the mt6315 driver, so spinlocks are
already used for the regmap access.

Fixes: b45b3ccef8c0 ("spmi: mediatek: Add support for MT6873/8192")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20230724154739.493724-1-nfraprado@collabora.com
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20231206231733.4031901-2-sboyd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>