Linus Torvalds [Thu, 28 Mar 2019 15:23:45 +0000 (08:23 -0700)]
Merge tag 'armsoc-fixes' of git://git./linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"A couple of minor fixes only for now
- fix for incorrect DMA channels on Renesas R-Car
- Broadcom bcm2835 error handling fixes
- Kconfig dependency fixes for bcm2835 and davinci
- CPU idle wakeup fix for i.MX6
- MMC regression on Tegra186
- fix incorrect phy settings on one imx board"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
arm64: tegra: Disable CQE Support for SDMMC4 on Tegra186
ARM: dts: nomadik: Fix polarity of SPI CS
ARM: davinci: fix build failure with allnoconfig
ARM: imx_v4_v5_defconfig: enable PWM driver
ARM: imx_v6_v7_defconfig: continue compiling the pwm driver
ARM: dts: imx6dl-yapp4: Use correct pseudo PHY address for the switch
ARM: dts: imx6qdl: Fix typo in imx6qdl-icore-rqs.dtsi
ARM: dts: imx6ull: Use the correct style for SPDX License Identifier
ARM: dts: pfla02: increase phy reset duration
ARM: imx6q: cpuidle: fix bug that CPU might not wake up at expected time
ARM: imx51: fix a leaked reference by adding missing of_node_put
ARM: dts: imx6dl-yapp4: Use rgmii-id phy mode on the cpu port
arm64: bcm2835: Add missing dependency on MFD_CORE.
ARM: dts: bcm283x: Fix hdmi hpd gpio pull
soc: bcm: bcm2835-pm: Fix error paths of initialization.
soc: bcm: bcm2835-pm: Fix PM_IMAGE_PERI power domain support.
arm64: dts: renesas: r8a774c0: Fix SCIF5 DMA channels
arm64: dts: renesas: r8a77990: Fix SCIF5 DMA channels
Linus Torvalds [Wed, 27 Mar 2019 19:22:57 +0000 (12:22 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
"Fixes here and there, a couple new device IDs, as usual:
1) Fix BQL race in dpaa2-eth driver, from Ioana Ciornei.
2) Fix 64-bit division in iwlwifi, from Arnd Bergmann.
3) Fix documentation for some eBPF helpers, from Quentin Monnet.
4) Some UAPI bpf header sync with tools, also from Quentin Monnet.
5) Set descriptor ownership bit at the right time for jumbo frames in
stmmac driver, from Aaro Koskinen.
6) Set IFF_UP properly in tun driver, from Eric Dumazet.
7) Fix load/store doubleword instruction generation in powerpc eBPF
JIT, from Naveen N. Rao.
8) nla_nest_start() return value checks all over, from Kangjie Lu.
9) Fix asoc_id handling in SCTP after the SCTP_*_ASSOC changes this
merge window. From Marcelo Ricardo Leitner and Xin Long.
10) Fix memory corruption with large MTUs in stmmac, from Aaro
Koskinen.
11) Do not use ipv4 header for ipv6 flows in TCP and DCCP, from Eric
Dumazet.
12) Fix topology subscription cancellation in tipc, from Erik Hugne.
13) Memory leak in genetlink error path, from Yue Haibing.
14) Valid control actions properly in packet scheduler, from Davide
Caratti.
15) Even if we get EEXIST, we still need to rehash if a shrink was
delayed. From Herbert Xu.
16) Fix interrupt mask handling in interrupt handler of r8169, from
Heiner Kallweit.
17) Fix leak in ehea driver, from Wen Yang"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (168 commits)
dpaa2-eth: fix race condition with bql frame accounting
chelsio: use BUG() instead of BUG_ON(1)
net: devlink: skip info_get op call if it is not defined in dumpit
net: phy: bcm54xx: Encode link speed and activity into LEDs
tipc: change to check tipc_own_id to return in tipc_net_stop
net: usb: aqc111: Extend HWID table by QNAP device
net: sched: Kconfig: update reference link for PIE
net: dsa: qca8k: extend slave-bus implementations
net: dsa: qca8k: remove leftover phy accessors
dt-bindings: net: dsa: qca8k: support internal mdio-bus
dt-bindings: net: dsa: qca8k: fix example
net: phy: don't clear BMCR in genphy_soft_reset
bpf, libbpf: clarify bump in libbpf version info
bpf, libbpf: fix version info and add it to shared object
rxrpc: avoid clang -Wuninitialized warning
tipc: tipc clang warning
net: sched: fix cleanup NULL pointer exception in act_mirr
r8169: fix cable re-plugging issue
net: ethernet: ti: fix possible object reference leak
net: ibm: fix possible object reference leak
...
Linus Torvalds [Tue, 26 Mar 2019 21:25:48 +0000 (14:25 -0700)]
Merge tag 'nfs-for-5.1-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
Stable fixes:
- Fix nfs4_lock_state refcounting in nfs4_alloc_{lock,unlock}data()
- fix mount/umount race in nlmclnt.
- NFSv4.1 don't free interrupted slot on open
Bugfixes:
- Don't let RPC_SOFTCONN tasks time out if the transport is connected
- Fix a typo in nfs_init_timeout_values()
- Fix layoutstats handling during read failovers
- fix uninitialized variable warning"
* tag 'nfs-for-5.1-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
SUNRPC: fix uninitialized variable warning
pNFS/flexfiles: Fix layoutstats handling during read failovers
NFS: Fix a typo in nfs_init_timeout_values()
SUNRPC: Don't let RPC_SOFTCONN tasks time out if the transport is connected
NFSv4.1 don't free interrupted slot on open
NFS: fix mount/umount race in nlmclnt.
NFS: Fix nfs4_lock_state refcounting in nfs4_alloc_{lock,unlock}data()
Alakesh Haloi [Tue, 26 Mar 2019 02:00:01 +0000 (02:00 +0000)]
SUNRPC: fix uninitialized variable warning
Avoid following compiler warning on uninitialized variable
net/sunrpc/xprtsock.c: In function ‘xs_read_stream_request.constprop’:
net/sunrpc/xprtsock.c:525:10: warning: ‘read’ may be used uninitialized in this function [-Wmaybe-uninitialized]
return read;
^~~~
net/sunrpc/xprtsock.c:529:23: warning: ‘ret’ may be used uninitialized in this function [-Wmaybe-uninitialized]
return ret < 0 ? ret : read;
~~~~~~~~~~~~~~^~~~~~
Signed-off-by: Alakesh Haloi <alakesh.haloi@gmail.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Ioana Ciornei [Mon, 25 Mar 2019 13:06:22 +0000 (13:06 +0000)]
dpaa2-eth: fix race condition with bql frame accounting
It might happen that Tx conf acknowledges a frame before it was
subscribed in bql, as subscribing was previously done after the enqueue
operation.
This patch moves the netdev_tx_sent_queue call before the actual frame
enqueue, so that this can never happen.
Fixes:
569dac6a5a0d ("dpaa2-eth: bql support")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Mon, 25 Mar 2019 12:49:16 +0000 (13:49 +0100)]
chelsio: use BUG() instead of BUG_ON(1)
clang warns about possible bugs in a dead code branch after
BUG_ON(1) when CONFIG_PROFILE_ALL_BRANCHES is enabled:
drivers/net/ethernet/chelsio/cxgb4/sge.c:479:3: error: variable 'buf_size' is used uninitialized whenever 'if'
condition is false [-Werror,-Wsometimes-uninitialized]
BUG_ON(1);
^~~~~~~~~
include/asm-generic/bug.h:61:36: note: expanded from macro 'BUG_ON'
#define BUG_ON(condition) do { if (unlikely(condition)) BUG(); } while (0)
^~~~~~~~~~~~~~~~~~~
include/linux/compiler.h:48:23: note: expanded from macro 'unlikely'
# define unlikely(x) (__branch_check__(x, 0, __builtin_constant_p(x)))
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/chelsio/cxgb4/sge.c:482:9: note: uninitialized use occurs here
return buf_size;
^~~~~~~~
drivers/net/ethernet/chelsio/cxgb4/sge.c:479:3: note: remove the 'if' if its condition is always true
BUG_ON(1);
^
include/asm-generic/bug.h:61:32: note: expanded from macro 'BUG_ON'
#define BUG_ON(condition) do { if (unlikely(condition)) BUG(); } while (0)
^
drivers/net/ethernet/chelsio/cxgb4/sge.c:459:14: note: initialize the variable 'buf_size' to silence this warning
int buf_size;
^
= 0
Use BUG() here to create simpler code that clang understands
correctly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Sat, 23 Mar 2019 23:21:03 +0000 (00:21 +0100)]
net: devlink: skip info_get op call if it is not defined in dumpit
In dumpit, unlike doit, the check for info_get op being defined
is missing. Add it and avoid null pointer dereference in case driver
does not define this op.
Fixes:
f9cf22882c60 ("devlink: add device information API")
Reported-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sat, 23 Mar 2019 22:18:46 +0000 (00:18 +0200)]
net: phy: bcm54xx: Encode link speed and activity into LEDs
Previously the green and amber LEDs on this quad PHY were solid, to
indicate an encoding of the link speed (10/100/1000).
This keeps the LEDs always on just as before, but now they flash on
Rx/Tx activity.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sat, 23 Mar 2019 16:48:22 +0000 (00:48 +0800)]
tipc: change to check tipc_own_id to return in tipc_net_stop
When running a syz script, a panic occurred:
[ 156.088228] BUG: KASAN: use-after-free in tipc_disc_timeout+0x9c9/0xb20 [tipc]
[ 156.094315] Call Trace:
[ 156.094844] <IRQ>
[ 156.095306] dump_stack+0x7c/0xc0
[ 156.097346] print_address_description+0x65/0x22e
[ 156.100445] kasan_report.cold.3+0x37/0x7a
[ 156.102402] tipc_disc_timeout+0x9c9/0xb20 [tipc]
[ 156.106517] call_timer_fn+0x19a/0x610
[ 156.112749] run_timer_softirq+0xb51/0x1090
It was caused by the netns freed without deleting the discoverer timer,
while later on the netns would be accessed in the timer handler.
The timer should have been deleted by tipc_net_stop() when cleaning up a
netns. However, tipc has been able to enable a bearer and start d->timer
without the local node_addr set since Commit
52dfae5c85a4 ("tipc: obtain
node identity from interface by default"), which caused the timer not to
be deleted in tipc_net_stop() then.
So fix it in tipc_net_stop() by changing to check local node_id instead
of local node_addr, as Jon suggested.
While at it, remove the calling of tipc_nametbl_withdraw() there, since
tipc_nametbl_stop() will take of the nametbl's freeing after.
Fixes:
52dfae5c85a4 ("tipc: obtain node identity from interface by default")
Reported-by: syzbot+a25307ad099309f1c2b9@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Bezrukov [Sat, 23 Mar 2019 13:59:53 +0000 (13:59 +0000)]
net: usb: aqc111: Extend HWID table by QNAP device
New device of QNAP based on aqc111u
Add this ID to blacklist of cdc_ether driver as well
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leslie Monis [Sat, 23 Mar 2019 13:41:33 +0000 (19:11 +0530)]
net: sched: Kconfig: update reference link for PIE
RFC 8033 replaces the IETF draft for PIE
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christian Lamparter [Fri, 22 Mar 2019 00:05:03 +0000 (01:05 +0100)]
net: dsa: qca8k: extend slave-bus implementations
This patch implements accessors for the QCA8337 MDIO access
through the MDIO_MASTER register, which makes it possible to
access the PHYs on slave-bus through the switch. In cases
where the switch ports are already mapped via external
"phy-phandles", the internal mdio-bus is disabled in order to
prevent a duplicated discovery and enumeration of the same
PHYs. Don't use mixed external and internal mdio-bus
configurations, as this is not supported by the hardware.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christian Lamparter [Fri, 22 Mar 2019 00:05:02 +0000 (01:05 +0100)]
net: dsa: qca8k: remove leftover phy accessors
This belated patch implements Andrew Lunn's request of
"remove the phy_read() and phy_write() functions."
<https://lore.kernel.org/patchwork/comment/902734/>
While seemingly harmless, this causes the switch's user
port PHYs to get registered twice. This is because the
DSA subsystem will create a slave mdio-bus not knowing
that the qca8k_phy_(read|write) accessors operate on
the external mdio-bus. So the same "bus" gets effectively
duplicated.
Cc: stable@vger.kernel.org
Fixes:
6b93fb46480a ("net-next: dsa: add new driver for qca8xxx family")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christian Lamparter [Fri, 22 Mar 2019 00:05:01 +0000 (01:05 +0100)]
dt-bindings: net: dsa: qca8k: support internal mdio-bus
This patch updates the qca8k's binding to document to the
approach for using the internal mdio-bus of the supported
qca8k switches.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christian Lamparter [Fri, 22 Mar 2019 00:05:00 +0000 (01:05 +0100)]
dt-bindings: net: dsa: qca8k: fix example
In the example, the phy at phy@0 is clashing with
the switch0@0 at the same address. Usually, the switches
are accessible through pseudo PHYs which in case of the
qca8k are located at 0x10 - 0x18.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 26 Mar 2019 17:32:13 +0000 (10:32 -0700)]
Merge tag 'for-5.1-rc2-tag' of git://git./linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- fsync fixes: i_size for truncate vs fsync, dio vs buffered during
snapshotting, remove complicated but incomplete assertion
- removed excessive warnigs, misreported device stats updates
- fix raid56 page mapping for 32bit arch
- fixes reported by static analyzer
* tag 'for-5.1-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Btrfs: fix assertion failure on fsync with NO_HOLES enabled
btrfs: Avoid possible qgroup_rsv_size overflow in btrfs_calculate_inode_block_rsv_size
btrfs: Fix bound checking in qgroup_trace_new_subtree_blocks
btrfs: raid56: properly unmap parity page in finish_parity_scrub()
btrfs: don't report readahead errors and don't update statistics
Btrfs: fix file corruption after snapshotting due to mix of buffered/DIO writes
btrfs: remove WARN_ON in log_dir_items
Btrfs: fix incorrect file size after shrinking truncate and fsync
Linus Torvalds [Tue, 26 Mar 2019 17:21:55 +0000 (10:21 -0700)]
Merge tag 'trace-v5.1-rc2' of git://git./linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Three small fixes:
- A fix to a double free in the histogram code
- Uninitialized variable fix
- Use NULL instead of zero fix and spelling fixes"
* tag 'trace-v5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace: Fix warning using plain integer as NULL & spelling corrections
tracing: initialize variable in create_dyn_event()
tracing: Remove unnecessary var_ref destroy in track_data_destroy()
Linus Torvalds [Tue, 26 Mar 2019 17:06:29 +0000 (10:06 -0700)]
Merge tag 'locks-v5.1' of git://git./linux/kernel/git/jlayton/linux
Pull file locking bugfix from Jeff Layton:
"Just a single fix for a bug that crept into POSIX lock deadlock
detection in v5.0"
* tag 'locks-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux:
locks: wake any locks blocked on request before deadlock check
Hariprasad Kelam [Sat, 23 Mar 2019 18:35:23 +0000 (00:05 +0530)]
ftrace: Fix warning using plain integer as NULL & spelling corrections
Changed 0 --> NULL to avoid sparse warning
Corrected spelling mistakes reported by checkpatch.pl
Sparse warning below:
sudo make C=2 CF=-D__CHECK_ENDIAN__ M=kernel/trace
CHECK kernel/trace/ftrace.c
kernel/trace/ftrace.c:3007:24: warning: Using plain integer as NULL pointer
kernel/trace/ftrace.c:4758:37: warning: Using plain integer as NULL pointer
Link: http://lkml.kernel.org/r/20190323183523.GA2244@hari-Inspiron-1545
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Frank Rowand [Fri, 22 Mar 2019 06:58:20 +0000 (23:58 -0700)]
tracing: initialize variable in create_dyn_event()
Fix compile warning in create_dyn_event(): 'ret' may be used uninitialized
in this function [-Wuninitialized].
Link: http://lkml.kernel.org/r/1553237900-8555-1-git-send-email-frowand.list@gmail.com
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Tom Zanussi <tom.zanussi@linux.intel.com>
Cc: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
Fixes:
5448d44c3855 ("tracing: Add unified dynamic event framework")
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Tom Zanussi [Wed, 20 Mar 2019 17:53:33 +0000 (12:53 -0500)]
tracing: Remove unnecessary var_ref destroy in track_data_destroy()
Commit
656fe2ba85e8 (tracing: Use hist trigger's var_ref array to
destroy var_refs) centralized the destruction of all the var_refs
in one place so that other code didn't have to do it.
The track_data_destroy() added later ignored that and also destroyed
the track_data var_ref, causing a double-free error flagged by KASAN.
==================================================================
BUG: KASAN: use-after-free in destroy_hist_field+0x30/0x70
Read of size 8 at addr
ffff888086df2210 by task bash/1694
CPU: 6 PID: 1694 Comm: bash Not tainted 5.1.0-rc1-test+ #15
Hardware name: Hewlett-Packard HP Compaq Pro 6300 SFF/339A, BIOS K01 v03.03
07/14/2016
Call Trace:
dump_stack+0x71/0xa0
? destroy_hist_field+0x30/0x70
print_address_description.cold.3+0x9/0x1fb
? destroy_hist_field+0x30/0x70
? destroy_hist_field+0x30/0x70
kasan_report.cold.4+0x1a/0x33
? __kasan_slab_free+0x100/0x150
? destroy_hist_field+0x30/0x70
destroy_hist_field+0x30/0x70
track_data_destroy+0x55/0xe0
destroy_hist_data+0x1f0/0x350
hist_unreg_all+0x203/0x220
event_trigger_open+0xbb/0x130
do_dentry_open+0x296/0x700
? stacktrace_count_trigger+0x30/0x30
? generic_permission+0x56/0x200
? __x64_sys_fchdir+0xd0/0xd0
? inode_permission+0x55/0x200
? security_inode_permission+0x18/0x60
path_openat+0x633/0x22b0
? path_lookupat.isra.50+0x420/0x420
? __kasan_kmalloc.constprop.12+0xc1/0xd0
? kmem_cache_alloc+0xe5/0x260
? getname_flags+0x6c/0x2a0
? do_sys_open+0x149/0x2b0
? do_syscall_64+0x73/0x1b0
? entry_SYSCALL_64_after_hwframe+0x44/0xa9
? _raw_write_lock_bh+0xe0/0xe0
? __kernel_text_address+0xe/0x30
? unwind_get_return_address+0x2f/0x50
? __list_add_valid+0x2d/0x70
? deactivate_slab.isra.62+0x1f4/0x5a0
? getname_flags+0x6c/0x2a0
? set_track+0x76/0x120
do_filp_open+0x11a/0x1a0
? may_open_dev+0x50/0x50
? _raw_spin_lock+0x7a/0xd0
? _raw_write_lock_bh+0xe0/0xe0
? __alloc_fd+0x10f/0x200
do_sys_open+0x1db/0x2b0
? filp_open+0x50/0x50
do_syscall_64+0x73/0x1b0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7fa7b24a4ca2
Code: 25 00 00 41 00 3d 00 00 41 00 74 4c 48 8d 05 85 7a 0d 00 8b 00 85 c0
75 6d 89 f2 b8 01 01 00 00 48 89 fe bf 9c ff ff ff 0f 05 <48> 3d 00 f0 ff ff
0f 87 a2 00 00 00 48 8b 4c 24 28 64 48 33 0c 25
RSP: 002b:
00007fffbafb3af0 EFLAGS:
00000246 ORIG_RAX:
0000000000000101
RAX:
ffffffffffffffda RBX:
000055d3648ade30 RCX:
00007fa7b24a4ca2
RDX:
0000000000000241 RSI:
000055d364a55240 RDI:
00000000ffffff9c
RBP:
00007fffbafb3bf0 R08:
0000000000000020 R09:
0000000000000002
R10:
00000000000001b6 R11:
0000000000000246 R12:
0000000000000000
R13:
0000000000000003 R14:
0000000000000001 R15:
000055d364a55240
==================================================================
So remove the track_data_destroy() destroy_hist_field() call for that
var_ref.
Link: http://lkml.kernel.org/r/1deffec420f6a16d11dd8647318d34a66d1989a9.camel@linux.intel.com
Fixes:
466f4528fbc69 ("tracing: Generalize hist trigger onmax and save action")
Reported-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Heiner Kallweit [Fri, 22 Mar 2019 19:00:20 +0000 (20:00 +0100)]
net: phy: don't clear BMCR in genphy_soft_reset
So far we effectively clear the BMCR register. Some PHY's can deal
with this (e.g. because they reset BMCR to a default as part of a
soft-reset) whilst on others this causes issues because e.g. the
autoneg bit is cleared. Marvell is an example, see also thread [0].
So let's be a little bit more gentle and leave all bits we're not
interested in as-is. This change is needed for PHY drivers to
properly deal with the original patch.
[0] https://marc.info/?t=
155264050700001&r=1&w=2
Fixes:
6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
Tested-by: Phil Reid <preid@electromag.com.au>
Tested-by: liweihang <liweihang@hisilicon.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 25 Mar 2019 21:49:00 +0000 (14:49 -0700)]
Revert "parport: daisy: use new parport device model"
This reverts commit
1aec4211204d9463d1fd209eb50453de16254599.
Steven Rostedt reports that it causes a hang at bootup and bisected it
to this commit.
The troigger is apparently a module alias for "parport_lowlevel" that
points to "parport_pc", which causes a hang with
modprobe -q -- parport_lowlevel
blocking forever with a backtrace like this:
wait_for_completion_killable+0x1c/0x28
call_usermodehelper_exec+0xa7/0x108
__request_module+0x351/0x3d8
get_lowlevel_driver+0x28/0x41 [parport]
__parport_register_driver+0x39/0x1f4 [parport]
daisy_drv_init+0x31/0x4f [parport]
parport_bus_init+0x5d/0x7b [parport]
parport_default_proc_register+0x26/0x1000 [parport]
do_one_initcall+0xc2/0x1e0
do_init_module+0x50/0x1d4
load_module+0x1c2e/0x21b3
sys_init_module+0xef/0x117
Supid says:
"Due to the new device model daisy driver will now try to find the
parallel ports while trying to register its driver so that it can bind
with them. Now, since daisy driver is loaded while parport bus is
initialising the list of parport is still empty and it tries to load
the lowlevel driver, which has an alias set to parport_pc, now causes
a deadlock"
But I don't think the daisy driver should be loaded by the parport
initialization in the first place, so let's revert the whole change.
If the daisy driver can just initialize separately on its own (like a
driver should), instead of hooking into the parport init sequence
directly, this issue probably would go away.
Reported-and-bisected-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Reported-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jonathan Hunter [Mon, 25 Mar 2019 11:28:07 +0000 (12:28 +0100)]
arm64: tegra: Disable CQE Support for SDMMC4 on Tegra186
Enabling CQE support on Tegra186 Jetson TX2 has introduced a regression
that is causing accesses to the file-system on the eMMC to fail. Errors
such as the following have been observed ...
mmc2: running CQE recovery
mmc2: mmc_select_hs400 failed, error -110
print_req_error: I/O error, dev mmcblk2, sector 8 flags 80700
mmc2: cqhci: CQE failed to exit halt state
For now disable CQE support for Tegra186 until this issue is resolved.
Fixes:
dfd3cb6feb73 arm64: tegra: Add CQE Support for SDMMC4
Signed-off-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Mon, 25 Mar 2019 16:06:41 +0000 (17:06 +0100)]
Merge tag 'imx-fixes-5.1' of git://git./linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.1:
- Correct phy mode setting of imx6dl-yapp4 board to fix a problem
caused by commit
5ecdd77c61c8 ("net: dsa: qca8k: disable delay
for RGMII mode").
- Add a missing of_node_put call to fix leaked reference detected by
coccinelle in imx51 machine code.
- Fix imx6q cpuidle driver bug which causes that CPU might not wake up
at expected time.
- Increase reset duration of Ethernet phy Micrel KSZ9031RNX to fix
transmission timeouts error seen on imx6qdl-phytec-pfla02 board.
- Correct SPDX License Identifier style for imx6ull-pinfunc-snvs.h.
- Fix 'bus-witdh' typos in imx6qdl-icore-rqs.dtsi.
- Correct pseudo PHY address of switch device for imx6dl-yapp4 board.
- Update PWM driver options in imx defconfig files due to the change
on driver part.
* tag 'imx-fixes-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx_v4_v5_defconfig: enable PWM driver
ARM: imx_v6_v7_defconfig: continue compiling the pwm driver
ARM: dts: imx6dl-yapp4: Use correct pseudo PHY address for the switch
ARM: dts: imx6qdl: Fix typo in imx6qdl-icore-rqs.dtsi
ARM: dts: imx6ull: Use the correct style for SPDX License Identifier
ARM: dts: pfla02: increase phy reset duration
ARM: imx6q: cpuidle: fix bug that CPU might not wake up at expected time
ARM: imx51: fix a leaked reference by adding missing of_node_put
ARM: dts: imx6dl-yapp4: Use rgmii-id phy mode on the cpu port
Arnd Bergmann [Mon, 25 Mar 2019 16:05:30 +0000 (17:05 +0100)]
Merge tag 'arm-soc/for-5.1/soc-fixes' of https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM/ARM64-based SoCs fixes for 5.1,
please pull the following:
- Eric provides fixes for the bcm2835-pm driver: added missing depends
on MFD_CORE for the ARM64 definition of ARCH_BCM2835, fixing error
paths on initialization and fixing the PM_IMAGE_PERI power domain
* tag 'arm-soc/for-5.1/soc-fixes' of https://github.com/Broadcom/stblinux:
arm64: bcm2835: Add missing dependency on MFD_CORE.
soc: bcm: bcm2835-pm: Fix error paths of initialization.
soc: bcm: bcm2835-pm: Fix PM_IMAGE_PERI power domain support.
Arnd Bergmann [Mon, 25 Mar 2019 16:04:47 +0000 (17:04 +0100)]
Merge tag 'arm-soc/for-5.1/devicetree-fixes' of https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
5.1, please pull the following:
- Helen fixes the HDMI hot-pug detect GPIO polarity for the Rasperry Pi
model B revision 2
* tag 'arm-soc/for-5.1/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm283x: Fix hdmi hpd gpio pull
Linus Walleij [Mon, 18 Mar 2019 15:31:22 +0000 (16:31 +0100)]
ARM: dts: nomadik: Fix polarity of SPI CS
The SPI DT bindings are for historical reasons a pitfall,
the ability to flag a GPIO line as active high/low with
the second cell flags was introduced later so the SPI
subsystem will only accept the bool flag spi-cs-high
to indicate that the line is active high.
It worked by mistake, but the mistake was corrected
in another commit.
The comment in the DTS file was also misleading: this
CS is indeed active high.
Fixes:
cffbb02dafa3 ("ARM: dts: nomadik: Augment NHK15 panel setting")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Mon, 25 Mar 2019 16:02:31 +0000 (17:02 +0100)]
Merge tag 'renesas-fixes-for-v5.1' of git://git./linux/kernel/git/horms/renesas into arm/fixes
Renesas ARM Based SoC Fixes for v5.1
R-Car Gen3 E3 (r8a77990) and RZ/G2E (r8a774c0) SoCs:
* Correct SCIF5 DMA channels
* tag 'renesas-fixes-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: renesas: r8a774c0: Fix SCIF5 DMA channels
arm64: dts: renesas: r8a77990: Fix SCIF5 DMA channels
Sekhar Nori [Wed, 20 Feb 2019 11:06:52 +0000 (16:36 +0530)]
ARM: davinci: fix build failure with allnoconfig
allnoconfig build with just ARCH_DAVINCI enabled
fails because drivers/clk/davinci/* depends on
REGMAP being enabled.
Fix it by selecting REGMAP_MMIO when building in
DaVinci support.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Jeff Layton [Mon, 25 Mar 2019 12:15:14 +0000 (08:15 -0400)]
locks: wake any locks blocked on request before deadlock check
Andreas reported that he was seeing the tdbtorture test fail in some
cases with -EDEADLCK when it wasn't before. Some debugging showed that
deadlock detection was sometimes discovering the caller's lock request
itself in a dependency chain.
While we remove the request from the blocked_lock_hash prior to
reattempting to acquire it, any locks that are blocked on that request
will still be present in the hash and will still have their fl_blocker
pointer set to the current request.
This causes posix_locks_deadlock to find a deadlock dependency chain
when it shouldn't, as a lock request cannot block itself.
We are going to end up waking all of those blocked locks anyway when we
go to reinsert the request back into the blocked_lock_hash, so just do
it prior to checking for deadlocks. This ensures that any lock blocked
on the current request will no longer be part of any blocked request
chain.
URL: https://bugzilla.kernel.org/show_bug.cgi?id=202975
Fixes:
5946c4319ebb ("fs/locks: allow a lock request to block other requests.")
Cc: stable@vger.kernel.org
Reported-by: Andreas Schneider <asn@redhat.com>
Signed-off-by: Neil Brown <neilb@suse.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
David S. Miller [Mon, 25 Mar 2019 03:45:35 +0000 (23:45 -0400)]
Merge git://git./pub/scm/linux/kernel/git/bpf/bpf
Alexei Starovoitov says:
====================
pull-request: bpf 2019-03-24
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) libbpf verision fix up from Daniel.
2) fix liveness propagation from Jakub.
3) fix verbose print of refcounted regs from Martin.
4) fix for large map allocations from Martynas.
5) fix use after free in sanitize_ptr_alu from Xu.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov [Mon, 25 Mar 2019 02:49:04 +0000 (19:49 -0700)]
Merge branch 'libbpf-fixup'
Daniel Borkmann says:
====================
First one is fixing version in Makefile and shared object and
second one clarifies bump in version. Thanks!
v1 -> v2:
- Fix up soname, thanks Stanislav!
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Daniel Borkmann [Sat, 23 Mar 2019 00:49:11 +0000 (01:49 +0100)]
bpf, libbpf: clarify bump in libbpf version info
The current documentation suggests that we would need to bump the
libbpf version on every change. Lets clarify this a bit more and
reflect what we do today in practice, that is, bumping it once per
development cycle.
Fixes:
76d1b894c515 ("libbpf: Document API and ABI conventions")
Reported-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Daniel Borkmann [Sat, 23 Mar 2019 00:49:10 +0000 (01:49 +0100)]
bpf, libbpf: fix version info and add it to shared object
Even though libbpf's versioning script for the linker (libbpf.map)
is pointing to 0.0.2, the BPF_EXTRAVERSION in the Makefile has
not been updated along with it and is therefore still on 0.0.1.
While fixing up, I also noticed that the generated shared object
versioning information is missing, typical convention is to have
a linker name (libbpf.so), soname (libbpf.so.0) and real name
(libbpf.so.0.0.2) for library management. This is based upon the
LIBBPF_VERSION as well.
The build will then produce the following bpf libraries:
# ll libbpf*
libbpf.a
libbpf.so -> libbpf.so.0.0.2
libbpf.so.0 -> libbpf.so.0.0.2
libbpf.so.0.0.2
# readelf -d libbpf.so.0.0.2 | grep SONAME
0x000000000000000e (SONAME) Library soname: [libbpf.so.0]
And install them accordingly:
# rm -rf /tmp/bld; mkdir /tmp/bld; make -j$(nproc) O=/tmp/bld install
Auto-detecting system features:
... libelf: [ on ]
... bpf: [ on ]
CC /tmp/bld/libbpf.o
CC /tmp/bld/bpf.o
CC /tmp/bld/nlattr.o
CC /tmp/bld/btf.o
CC /tmp/bld/libbpf_errno.o
CC /tmp/bld/str_error.o
CC /tmp/bld/netlink.o
CC /tmp/bld/bpf_prog_linfo.o
CC /tmp/bld/libbpf_probes.o
CC /tmp/bld/xsk.o
LD /tmp/bld/libbpf-in.o
LINK /tmp/bld/libbpf.a
LINK /tmp/bld/libbpf.so.0.0.2
LINK /tmp/bld/test_libbpf
INSTALL /tmp/bld/libbpf.a
INSTALL /tmp/bld/libbpf.so.0.0.2
# ll /usr/local/lib64/libbpf.*
/usr/local/lib64/libbpf.a
/usr/local/lib64/libbpf.so -> libbpf.so.0.0.2
/usr/local/lib64/libbpf.so.0 -> libbpf.so.0.0.2
/usr/local/lib64/libbpf.so.0.0.2
Fixes:
1bf4b05810fe ("tools: bpftool: add probes for eBPF program types")
Fixes:
1b76c13e4b36 ("bpf tools: Introduce 'bpf' library and add bpf feature check")
Reported-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Linus Torvalds [Sun, 24 Mar 2019 21:02:26 +0000 (14:02 -0700)]
Linux 5.1-rc2
Linus Torvalds [Sun, 24 Mar 2019 20:41:37 +0000 (13:41 -0700)]
Merge tag 'ext4_for_linus_stable' of git://git./linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Miscellaneous ext4 bug fixes for 5.1"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: prohibit fstrim in norecovery mode
ext4: cleanup bh release code in ext4_ind_remove_space()
ext4: brelse all indirect buffer in ext4_ind_remove_space()
ext4: report real fs size after failed resize
ext4: add missing brelse() in add_new_gdb_meta_bg()
ext4: remove useless ext4_pin_inode()
ext4: avoid panic during forced reboot
ext4: fix data corruption caused by unaligned direct AIO
ext4: fix NULL pointer dereference while journal is aborted
Linus Torvalds [Sun, 24 Mar 2019 18:42:10 +0000 (11:42 -0700)]
Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull scheduler updates from Thomas Gleixner:
"Third more careful attempt for this set of fixes:
- Prevent a 32bit math overflow in the cpufreq code
- Fix a buffer overflow when scanning the cgroup2 cpu.max property
- A set of fixes for the NOHZ scheduler logic to prevent waking up
CPUs even if the capacity of the busy CPUs is sufficient along with
other tweaks optimizing the behaviour for asymmetric systems
(big/little)"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Skip LLC NOHZ logic for asymmetric systems
sched/fair: Tune down misfit NOHZ kicks
sched/fair: Comment some nohz_balancer_kick() kick conditions
sched/core: Fix buffer overflow in cgroup2 property cpu.max
sched/cpufreq: Fix 32-bit math overflow
Linus Torvalds [Sun, 24 Mar 2019 18:16:27 +0000 (11:16 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf updates from Thomas Gleixner:
"A larger set of perf updates.
Not all of them are strictly fixes, but that's solely the tip
maintainers fault as they let the timely -rc1 pull request fall
through the cracks for various reasons including travel. So I'm
sending this nevertheless because rebasing and distangling fixes and
updates would be a mess and risky as well. As of tomorrow, a strict
fixes separation is happening again. Sorry for the slip-up.
Kernel:
- Handle RECORD_MMAP vs. RECORD_MMAP2 correctly so different
consumers of the mmap event get what they requested.
Tools:
- A larger set of updates to perf record/report/scripts vs. time
stamp handling
- More Python3 fixups
- A pile of memory leak plumbing
- perf BPF improvements and fixes
- Finalize the perf.data directory storage"
[ Note: the kernel part is strictly a fix, the updates are purely to
tooling - Linus ]
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (75 commits)
perf bpf: Show more BPF program info in print_bpf_prog_info()
perf bpf: Extract logic to create program names from perf_event__synthesize_one_bpf_prog()
perf tools: Save bpf_prog_info and BTF of new BPF programs
perf evlist: Introduce side band thread
perf annotate: Enable annotation of BPF programs
perf build: Check what binutils's 'disassembler()' signature to use
perf bpf: Process PERF_BPF_EVENT_PROG_LOAD for annotation
perf symbols: Introduce DSO_BINARY_TYPE__BPF_PROG_INFO
perf feature detection: Add -lopcodes to feature-libbfd
perf top: Add option --no-bpf-event
perf bpf: Save BTF information as headers to perf.data
perf bpf: Save BTF in a rbtree in perf_env
perf bpf: Save bpf_prog_info information as headers to perf.data
perf bpf: Save bpf_prog_info in a rbtree in perf_env
perf bpf: Make synthesize_bpf_events() receive perf_session pointer instead of perf_tool
perf bpf: Synthesize bpf events with bpf_program__get_prog_info_linear()
bpftool: use bpf_program__get_prog_info_linear() in prog.c:do_dump()
tools lib bpf: Introduce bpf_program__get_prog_info_linear()
perf record: Replace option --bpf-event with --no-bpf-event
perf tests: Fix a memory leak in test__perf_evsel__tp_sched_test()
...
Linus Torvalds [Sun, 24 Mar 2019 18:12:27 +0000 (11:12 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of x86 fixes:
- Prevent potential NULL pointer dereferences in the HPET and HyperV
code
- Exclude the GART aperture from /proc/kcore to prevent kernel
crashes on access
- Use the correct macros for Cyrix I/O on Geode processors
- Remove yet another kernel address printk leak
- Announce microcode reload completion as requested by quite some
people. Microcode loading has become popular recently.
- Some 'Make Clang' happy fixlets
- A few cleanups for recently added code"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/gart: Exclude GART aperture from kcore
x86/hw_breakpoints: Make default case in hw_breakpoint_arch_parse() return an error
x86/mm/pti: Make local symbols static
x86/cpu/cyrix: Remove {get,set}Cx86_old macros used for Cyrix processors
x86/cpu/cyrix: Use correct macros for Cyrix calls on Geode processors
x86/microcode: Announce reload operation's completion
x86/hyperv: Prevent potential NULL pointer dereference
x86/hpet: Prevent potential NULL pointer dereference
x86/lib: Fix indentation issue, remove extra tab
x86/boot: Restrict header scope to make Clang happy
x86/mm: Don't leak kernel addresses
x86/cpufeature: Fix various quality problems in the <asm/cpu_device_hd.h> header
Linus Torvalds [Sun, 24 Mar 2019 18:09:47 +0000 (11:09 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"A set of small fixes plus the removal of stale board support code:
- Remove the board support code from the clpx711x clocksource driver.
This change had fallen through the cracks and I'm sending it now
rather than dealing with people who want to improve that stale code
for 3 month.
- Use the proper clocksource mask on RICSV
- Make local scope functions and variables static"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/clps711x: Remove board support
clocksource/drivers/riscv: Fix clocksource mask
clocksource/drivers/mips-gic-timer: Make gic_compare_irqaction static
clocksource/drivers/timer-ti-dm: Make omap_dm_timer_set_load_start() static
clocksource/drivers/tcb_clksrc: Make tc_clksrc_suspend/resume() static
clocksource/drivers/clps711x: Make clps711x_clksrc_init() static
time/jiffies: Make refined_jiffies static
Linus Torvalds [Sun, 24 Mar 2019 17:58:01 +0000 (10:58 -0700)]
Merge branch 'locking-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull locking fixes from Thomas Gleixner:
"Two small fixes:
- Cure a recently introduces error path hickup which tries to
unregister a not registered lockdep key in te workqueue code
- Prevent unaligned cmpxchg() crashes in the robust list handling
code by sanity checking the user space supplied futex pointer"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex: Ensure that futex address is aligned in handle_futex_death()
workqueue: Only unregister a registered lockdep key
Linus Torvalds [Sun, 24 Mar 2019 17:51:23 +0000 (10:51 -0700)]
Merge branch 'irq-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A set of fixes for the interrupt subsystem:
- Remove secondary GIC support on systems w/o device-tree support
- A set of small fixlets in various irqchip drivers
- static and fall-through annotations
- Kernel doc and typo fixes"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Mark expected switch case fall-through
genirq/devres: Remove excess parameter from kernel doc
irqchip/irq-mvebu-sei: Make mvebu_sei_ap806_caps static
irqchip/mbigen: Don't clear eventid when freeing an MSI
irqchip/stm32: Don't set rising configuration registers at init
irqchip/stm32: Don't clear rising/falling config registers at init
dt-bindings: irqchip: renesas-irqc: Document r8a774c0 support
irqchip/mmp: Make mmp_irq_domain_ops static
irqchip/brcmstb-l2: Make two init functions static
genirq: Fix typo in comment of IRQD_MOVE_PCNTXT
irqchip/gic-v3-its: Fix comparison logic in lpi_range_cmp
irqchip/gic: Drop support for secondary GIC in non-DT systems
irqchip/imx-irqsteer: Fix of_property_read_u32() error handling
Linus Torvalds [Sun, 24 Mar 2019 17:17:33 +0000 (10:17 -0700)]
Merge branch 'core-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull core fixes from Thomas Gleixner:
"Two small fixes:
- Move the large objtool_file struct off the stack so objtool works
in setups with a tight stack limit.
- Make a few variables static in the watchdog core code"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
watchdog/core: Make variables static
objtool: Move objtool_file struct off the stack
Linus Torvalds [Sun, 24 Mar 2019 17:01:53 +0000 (10:01 -0700)]
Merge branch 'next' of git://git./linux/kernel/git/rzhang/linux
Pull thermal management fixes from Zhang Rui:
- Fix a wrong __percpu structure declaration in intel_powerclamp driver
(Luc Van Oostenryck)
- Fix truncated name of the idle injection kthreads created by
intel_powerclamp driver (Zhang Rui)
- Fix the missing UUID supports in int3400 thermal driver (Matthew
Garrett)
- Fix a crash when accessing the debugfs of bcm2835 SoC thermal driver
(Phil Elwell)
- A couple of trivial fixes/cleanups in some SoC thermal drivers
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal/intel_powerclamp: fix truncated kthread name
thermal: mtk: Allocate enough space for mtk_thermal.
thermal/int340x_thermal: fix mode setting
thermal/int340x_thermal: Add additional UUIDs
thermal: cpu_cooling: Remove unused cur_freq variable
thermal: bcm2835: Fix crash in bcm2835_thermal_debugfs
thermal: samsung: Fix incorrect check after code merge
thermal/intel_powerclamp: fix __percpu declaration of worker_data
Linus Torvalds [Sun, 24 Mar 2019 16:58:08 +0000 (09:58 -0700)]
Merge tag '5.1-rc1-cifs-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull smb3 fixes from Steve French:
- two fixes for stable for guest mount problems with smb3.1.1
- two fixes for crediting (SMB3 flow control) on resent requests
- a byte range lock leak fix
- two fixes for incorrect rc mappings
* tag '5.1-rc1-cifs-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal module version number
SMB3: Fix SMB3.1.1 guest mounts to Samba
cifs: Fix slab-out-of-bounds when tracing SMB tcon
cifs: allow guest mounts to work for smb3.11
fix incorrect error code mapping for OBJECTID_NOT_FOUND
cifs: fix that return -EINVAL when do dedupe operation
CIFS: Fix an issue with re-sending rdata when transport returning -EAGAIN
CIFS: Fix an issue with re-sending wdata when transport returning -EAGAIN
Linus Torvalds [Sun, 24 Mar 2019 16:51:55 +0000 (09:51 -0700)]
Merge tag 'auxdisplay-for-linus-v5.1-rc2' of git://github.com/ojeda/linux
Pull auxdisplay updates from Miguel Ojeda:
"A few fixes and improvements for auxdisplay:
- Series to fix a memory leak in hd44780 while introducing
charlcd_free(). From Andy Shevchenko
- Series to clean up the Kconfig menus and a couple of improvements
for charlcd. From Mans Rullgard"
* tag 'auxdisplay-for-linus-v5.1-rc2' of git://github.com/ojeda/linux:
auxdisplay: charlcd: make backlight initial state configurable
auxdisplay: charlcd: simplify init message display
auxdisplay: deconfuse configuration
auxdisplay: hd44780: Convert to use charlcd_free()
auxdisplay: panel: Convert to use charlcd_free()
auxdisplay: charlcd: Introduce charlcd_free() helper
auxdisplay: charlcd: Move to_priv() to charlcd namespace
auxdisplay: hd44780: Fix memory leak on ->remove()
Linus Torvalds [Sun, 24 Mar 2019 16:43:35 +0000 (09:43 -0700)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Six fixes to four drivers and two core fixes.
One core fix simply corrects a missed destroy_rcu_head() but the other
is hopefully the end of an ongoing effort to make suspend/resume play
nicely with scsi quiesce"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ibmvscsi: Fix empty event pool access during host removal
scsi: ibmvscsi: Protect ibmvscsi_head from concurrent modificaiton
scsi: hisi_sas: Add softreset in hisi_sas_I_T_nexus_reset()
scsi: qla2xxx: Fix NULL pointer crash due to stale CPUID
scsi: qla2xxx: Fix FC-AL connection target discovery
scsi: core: Avoid that a kernel warning appears during system resume
scsi: core: Also call destroy_rcu_head() for passthrough requests
scsi: iscsi: flush running unbind operations when removing a session
Alexander Shiyan [Thu, 20 Dec 2018 11:16:26 +0000 (14:16 +0300)]
clocksource/drivers/clps711x: Remove board support
Since board support for the CLPS711X platform was removed,
remove the board support from the clps711x-timer driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lkml.kernel.org/r/20181220111626.17140-1-shc_work@mail.ru
Arnd Bergmann [Fri, 22 Mar 2019 14:18:43 +0000 (15:18 +0100)]
rxrpc: avoid clang -Wuninitialized warning
clang produces a false-positive warning as it fails to notice
that "lost = true" implies that "ret" is initialized:
net/rxrpc/output.c:402:6: error: variable 'ret' is used uninitialized whenever 'if' condition is true [-Werror,-Wsometimes-uninitialized]
if (lost)
^~~~
net/rxrpc/output.c:437:6: note: uninitialized use occurs here
if (ret >= 0) {
^~~
net/rxrpc/output.c:402:2: note: remove the 'if' if its condition is always false
if (lost)
^~~~~~~~~
net/rxrpc/output.c:339:9: note: initialize the variable 'ret' to silence this warning
int ret, opt;
^
= 0
Rearrange the code to make that more obvious and avoid the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Maloy [Fri, 22 Mar 2019 14:03:51 +0000 (15:03 +0100)]
tipc: tipc clang warning
When checking the code with clang -Wsometimes-uninitialized we get the
following warning:
if (!tipc_link_is_establishing(l)) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
net/tipc/node.c:847:46: note: uninitialized use occurs here
tipc_bearer_xmit(n->net, bearer_id, &xmitq, maddr);
net/tipc/node.c:831:2: note: remove the 'if' if its condition is always
true
if (!tipc_link_is_establishing(l)) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
net/tipc/node.c:821:31: note: initialize the variable 'maddr' to silence
this warning
struct tipc_media_addr *maddr;
We fix this by initializing 'maddr' to NULL. For the matter of clarity,
we also test if 'xmitq' is non-empty before we use it and 'maddr'
further down in the function. It will never happen that 'xmitq' is non-
empty at the same time as 'maddr' is NULL, so this is a sufficient test.
Fixes:
598411d70f85 ("tipc: make resetting of links non-atomic")
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Hurley [Fri, 22 Mar 2019 12:37:35 +0000 (12:37 +0000)]
net: sched: fix cleanup NULL pointer exception in act_mirr
A new mirred action is created by the tcf_mirred_init function. This
contains a list head struct which is inserted into a global list on
successful creation of a new action. However, after a creation, it is
still possible to error out and call the tcf_idr_release function. This,
in turn, calls the act_mirr cleanup function via __tcf_idr_release and
__tcf_action_put. This cleanup function tries to delete the list entry
which is as yet uninitialised, leading to a NULL pointer exception.
Fix this by initialising the list entry on creation of a new action.
Bug report:
BUG: unable to handle kernel NULL pointer dereference at
0000000000000008
PGD
8000000840c73067 P4D
8000000840c73067 PUD
858dcc067 PMD 0
Oops: 0002 [#1] SMP PTI
CPU: 32 PID: 5636 Comm: handler194 Tainted: G OE 5.0.0+ #186
Hardware name: Dell Inc. PowerEdge R730/0599V5, BIOS 1.3.6 06/03/2015
RIP: 0010:tcf_mirred_release+0x42/0xa7 [act_mirred]
Code: f0 90 39 c0 e8 52 04 57 c8 48 c7 c7 b8 80 39 c0 e8 94 fa d4 c7 48 8b 93 d0 00 00 00 48 8b 83 d8 00 00 00 48 c7 c7 f0 90 39 c0 <48> 89 42 08 48 89 10 48 b8 00 01 00 00 00 00 ad de 48 89 83 d0 00
RSP: 0018:
ffffac4aa059f688 EFLAGS:
00010282
RAX:
0000000000000000 RBX:
ffff9dcd1b214d00 RCX:
0000000000000000
RDX:
0000000000000000 RSI:
ffff9dcd1fa165f8 RDI:
ffffffffc03990f0
RBP:
ffff9dccf9c7af80 R08:
0000000000000a3b R09:
0000000000000000
R10:
ffff9dccfa11f420 R11:
0000000000000000 R12:
0000000000000001
R13:
ffff9dcd16b433c0 R14:
ffff9dcd1b214d80 R15:
0000000000000000
FS:
00007f441bfff700(0000) GS:
ffff9dcd1fa00000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
0000000000000008 CR3:
0000000839e64004 CR4:
00000000001606e0
Call Trace:
tcf_action_cleanup+0x59/0xca
__tcf_action_put+0x54/0x6b
__tcf_idr_release.cold.33+0x9/0x12
tcf_mirred_init.cold.20+0x22e/0x3b0 [act_mirred]
tcf_action_init_1+0x3d0/0x4c0
tcf_action_init+0x9c/0x130
tcf_exts_validate+0xab/0xc0
fl_change+0x1ca/0x982 [cls_flower]
tc_new_tfilter+0x647/0x8d0
? load_balance+0x14b/0x9e0
rtnetlink_rcv_msg+0xe3/0x370
? __switch_to_asm+0x40/0x70
? __switch_to_asm+0x34/0x70
? _cond_resched+0x15/0x30
? __kmalloc_node_track_caller+0x1d4/0x2b0
? rtnl_calcit.isra.31+0xf0/0xf0
netlink_rcv_skb+0x49/0x110
netlink_unicast+0x16f/0x210
netlink_sendmsg+0x1df/0x390
sock_sendmsg+0x36/0x40
___sys_sendmsg+0x27b/0x2c0
? futex_wake+0x80/0x140
? do_futex+0x2b9/0xac0
? ep_scan_ready_list.constprop.22+0x1f2/0x210
? ep_poll+0x7a/0x430
__sys_sendmsg+0x47/0x80
do_syscall_64+0x55/0x100
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes:
4e232818bd32 ("net: sched: act_mirred: remove dependency on rtnl lock")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Fri, 22 Mar 2019 06:39:35 +0000 (07:39 +0100)]
r8169: fix cable re-plugging issue
Bartek reported that after few cable unplug/replug cycles suddenly
replug isn't detected any longer. His system uses a RTL8106, I wasn't
able to reproduce the issue with RTL8168g. According to his bisect
the referenced commit caused the regression. As Realtek doesn't
release datasheets or errata it's hard to say what's the actual root
cause, but this change was reported to fix the issue.
Fixes:
38caff5a445b ("r8169: handle all interrupt events in the hard irq handler")
Reported-by: Bartosz Skrzypczak <barteks2x@gmail.com>
Suggested-by: Bartosz Skrzypczak <barteks2x@gmail.com>
Tested-by: Bartosz Skrzypczak <barteks2x@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wen Yang [Fri, 22 Mar 2019 03:04:09 +0000 (11:04 +0800)]
net: ethernet: ti: fix possible object reference leak
The call to of_get_child_by_name returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/net/ethernet/ti/netcp_ethss.c:3661:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 3654, but without a corresponding object release within this function.
./drivers/net/ethernet/ti/netcp_ethss.c:3665:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 3654, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Wen Yang [Fri, 22 Mar 2019 03:04:08 +0000 (11:04 +0800)]
net: ibm: fix possible object reference leak
The call to ehea_get_eth_dn returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/net/ethernet/ibm/ehea/ehea_main.c:3163:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 3154, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Douglas Miller <dougmill@linux.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Wen Yang [Fri, 22 Mar 2019 03:04:07 +0000 (11:04 +0800)]
net: xilinx: fix possible object reference leak
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/net/ethernet/xilinx/xilinx_axienet_main.c:1624:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1569, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Anirudha Sarangi <anirudh@xilinx.com>
Cc: John Linn <John.Linn@xilinx.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 21 Mar 2019 23:34:44 +0000 (16:34 -0700)]
net: phy: Re-parent menus for MDIO bus drivers correctly
After
90eff9096c01 ("net: phy: Allow splitting MDIO bus/device support
from PHYs") the various MDIO bus drivers were no longer parented with
config PHYLIB but with config MDIO_BUS which is not a menuconfig, fix
this by depending on MDIO_DEVICE which is a menuconfig.
This is visually nicer and less confusing for users.
Fixes:
90eff9096c01 ("net: phy: Allow splitting MDIO bus/device support from PHYs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 23 Mar 2019 17:25:12 +0000 (10:25 -0700)]
Merge tag 'io_uring-
20190323' of git://git.kernel.dk/linux-block
Pull io_uring fixes and improvements from Jens Axboe:
"The first five in this series are heavily inspired by the work Al did
on the aio side to fix the races there.
The last two re-introduce a feature that was in io_uring before it got
merged, but which I pulled since we didn't have a good way to have
BVEC iters that already have a stable reference. These aren't
necessarily related to block, it's just how io_uring pins fixed
buffers"
* tag 'io_uring-
20190323' of git://git.kernel.dk/linux-block:
block: add BIO_NO_PAGE_REF flag
iov_iter: add ITER_BVEC_FLAG_NO_REF flag
io_uring: mark me as the maintainer
io_uring: retry bulk slab allocs as single allocs
io_uring: fix poll races
io_uring: fix fget/fput handling
io_uring: add prepped flag
io_uring: make io_read/write return an integer
io_uring: use regular request ref counts
Linus Torvalds [Sat, 23 Mar 2019 17:14:42 +0000 (10:14 -0700)]
Merge tag 'for-linus-
20190323' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A set of fixes/changes that should go into this series. This contains:
- Kernel doc / comment updates (Bart, Shenghui)
- Un-export of core-only used function (Bart)
- Fix race on loop file access (Dongli)
- pf/pcd queue cleanup fixes (me)
- Use appropriate helper for RESTART bit set (Yufen)
- Use named identifier for classic poll (Yufen)"
* tag 'for-linus-
20190323' of git://git.kernel.dk/linux-block:
sbitmap: trivial - update comment for sbitmap_deferred_clear_bit
blkcg: Fix kernel-doc warnings
blk-iolatency: #include "blk.h"
block: Unexport blk_mq_add_to_requeue_list()
block: add BLK_MQ_POLL_CLASSIC for hybrid poll and return EINVAL for unexpected value
blk-mq: remove unused 'nr_expired' from blk_mq_hw_ctx
loop: access lo_backing_file only when the loop device is Lo_bound
blk-mq: use blk_mq_sched_mark_restart_hctx to set RESTART
paride/pcd: cleanup queues when detection fails
paride/pf: cleanup queues when detection fails
Linus Torvalds [Sat, 23 Mar 2019 17:04:47 +0000 (10:04 -0700)]
Merge tag 'ceph-for-5.1-rc2' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"A follow up for the new alloc_size logic and a blacklisting fix,
marked for stable"
* tag 'ceph-for-5.1-rc2' of git://github.com/ceph/ceph-client:
rbd: drop wait_for_latest_osdmap()
libceph: wait for latest osdmap in ceph_monc_blacklist_add()
rbd: set io_min, io_opt and discard_granularity to alloc_size
Darrick J. Wong [Sat, 23 Mar 2019 16:10:29 +0000 (12:10 -0400)]
ext4: prohibit fstrim in norecovery mode
The ext4 fstrim implementation uses the block bitmaps to find free space
that can be discarded. If we haven't replayed the journal, the bitmaps
will be stale and we absolutely *cannot* use stale metadata to zap the
underlying storage.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Trond Myklebust [Sat, 23 Mar 2019 03:03:56 +0000 (23:03 -0400)]
pNFS/flexfiles: Fix layoutstats handling during read failovers
During a read failover, we may end up changing the value of
the pgio_mirror_idx, so make sure that we record the layout
stats before that update.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Trond Myklebust [Thu, 21 Mar 2019 21:57:56 +0000 (17:57 -0400)]
NFS: Fix a typo in nfs_init_timeout_values()
Specifying a retrans=0 mount parameter to a NFS/TCP mount, is
inadvertently causing the NFS client to rewrite any specified
timeout parameter to the default of 60 seconds.
Fixes:
a956beda19a6 ("NFS: Allow the mount option retrans=0")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
zhangyi (F) [Sat, 23 Mar 2019 15:56:01 +0000 (11:56 -0400)]
ext4: cleanup bh release code in ext4_ind_remove_space()
Currently, we are releasing the indirect buffer where we are done with
it in ext4_ind_remove_space(), so we can see the brelse() and
BUFFER_TRACE() everywhere. It seems fragile and hard to read, and we
may probably forget to release the buffer some day. This patch cleans
up the code by putting of the code which releases the buffers to the
end of the function.
Signed-off-by: zhangyi (F) <yi.zhang@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Trond Myklebust [Tue, 19 Mar 2019 15:24:54 +0000 (11:24 -0400)]
SUNRPC: Don't let RPC_SOFTCONN tasks time out if the transport is connected
If the transport is still connected, then we do want to allow
RPC_SOFTCONN tasks to retry. They should time out if and only if
the connection is broken.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
zhangyi (F) [Sat, 23 Mar 2019 15:43:05 +0000 (11:43 -0400)]
ext4: brelse all indirect buffer in ext4_ind_remove_space()
All indirect buffers get by ext4_find_shared() should be released no
mater the branch should be freed or not. But now, we forget to release
the lower depth indirect buffers when removing space from the same
higher depth indirect block. It will lead to buffer leak and futher
more, it may lead to quota information corruption when using old quota,
consider the following case.
- Create and mount an empty ext4 filesystem without extent and quota
features,
- quotacheck and enable the user & group quota,
- Create some files and write some data to them, and then punch hole
to some files of them, it may trigger the buffer leak problem
mentioned above.
- Disable quota and run quotacheck again, it will create two new
aquota files and write the checked quota information to them, which
probably may reuse the freed indirect block(the buffer and page
cache was not freed) as data block.
- Enable quota again, it will invoke
vfs_load_quota_inode()->invalidate_bdev() to try to clean unused
buffers and pagecache. Unfortunately, because of the buffer of quota
data block is still referenced, quota code cannot read the up to date
quota info from the device and lead to quota information corruption.
This problem can be reproduced by xfstests generic/231 on ext3 file
system or ext4 file system without extent and quota features.
This patch fix this problem by releasing the missing indirect buffers,
in ext4_ind_remove_space().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhangyi (F) <yi.zhang@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: stable@kernel.org
Gustavo A. R. Silva [Thu, 28 Feb 2019 21:37:14 +0000 (15:37 -0600)]
genirq: Mark expected switch case fall-through
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
With -Wimplicit-fallthrough added to CFLAGS:
kernel/irq/manage.c: In function ‘irq_do_set_affinity’:
kernel/irq/manage.c:198:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
cpumask_copy(desc->irq_common_data.affinity, mask);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
kernel/irq/manage.c:199:2: note: here
case IRQ_SET_MASK_OK_NOCOPY:
^~~~
Annotate it.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Kees Cook <keescook@chromium.org>
Link: https://lkml.kernel.org/r/20190228213714.GA9246@embeddedor
Atish Patra [Fri, 22 Mar 2019 21:54:11 +0000 (14:54 -0700)]
clocksource/drivers/riscv: Fix clocksource mask
For all riscv architectures (RV32, RV64 and RV128), the clocksource
is a 64 bit incrementing counter.
Fix the clock source mask accordingly.
Tested on both 64bit and 32 bit virt machine in QEMU.
Fixes:
62b019436814 ("clocksource: new RISC-V SBI timer driver")
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-riscv@lists.infradead.org
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Anup Patel <Anup.Patel@wdc.com>
Cc: Damien Le Moal <Damien.LeMoal@wdc.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190322215411.19362-1-atish.patra@wdc.com
Kairui Song [Fri, 8 Mar 2019 03:05:08 +0000 (11:05 +0800)]
x86/gart: Exclude GART aperture from kcore
On machines where the GART aperture is mapped over physical RAM,
/proc/kcore contains the GART aperture range. Accessing the GART range via
/proc/kcore results in a kernel crash.
vmcore used to have the same issue, until it was fixed with commit
2a3e83c6f96c ("x86/gart: Exclude GART aperture from vmcore")', leveraging
existing hook infrastructure in vmcore to let /proc/vmcore return zeroes
when attempting to read the aperture region, and so it won't read from the
actual memory.
Apply the same workaround for kcore. First implement the same hook
infrastructure for kcore, then reuse the hook functions introduced in the
previous vmcore fix. Just with some minor adjustment, rename some functions
for more general usage, and simplify the hook infrastructure a bit as there
is no module usage yet.
Suggested-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Kairui Song <kasong@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jiri Bohac <jbohac@suse.cz>
Acked-by: Baoquan He <bhe@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Dave Young <dyoung@redhat.com>
Link: https://lkml.kernel.org/r/20190308030508.13548-1-kasong@redhat.com
Steve French [Wed, 20 Mar 2019 21:42:50 +0000 (16:42 -0500)]
cifs: update internal module version number
To 2.19
Signed-off-by: Steve French <stfrench@microsoft.com>
Steve French [Sat, 23 Mar 2019 03:31:17 +0000 (22:31 -0500)]
SMB3: Fix SMB3.1.1 guest mounts to Samba
Workaround problem with Samba responses to SMB3.1.1
null user (guest) mounts. The server doesn't set the
expected flag in the session setup response so we have
to do a similar check to what is done in smb3_validate_negotiate
where we also check if the user is a null user (but not sec=krb5
since username might not be passed in on mount for Kerberos case).
Note that the commit below tightened the conditions and forced signing
for the SMB2-TreeConnect commands as per MS-SMB2.
However, this should only apply to normal user sessions and not for
cases where there is no user (even if server forgets to set the flag
in the response) since we don't have anything useful to sign with.
This is especially important now that the more secure SMB3.1.1 protocol
is in the default dialect list.
An earlier patch ("cifs: allow guest mounts to work for smb3.11") fixed
the guest mounts to Windows.
Fixes:
6188f28bf608 ("Tree connect for SMB3.1.1 must be signed for non-encrypted shares")
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Reviewed-by: Paulo Alcantara <palcantara@suse.de>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Paulo Alcantara (SUSE) [Thu, 21 Mar 2019 22:31:22 +0000 (19:31 -0300)]
cifs: Fix slab-out-of-bounds when tracing SMB tcon
This patch fixes the following KASAN report:
[ 779.044746] BUG: KASAN: slab-out-of-bounds in string+0xab/0x180
[ 779.044750] Read of size 1 at addr
ffff88814f327968 by task trace-cmd/2812
[ 779.044756] CPU: 1 PID: 2812 Comm: trace-cmd Not tainted 5.1.0-rc1+ #62
[ 779.044760] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-0-ga698c89-prebuilt.qemu.org 04/01/2014
[ 779.044761] Call Trace:
[ 779.044769] dump_stack+0x5b/0x90
[ 779.044775] ? string+0xab/0x180
[ 779.044781] print_address_description+0x6c/0x23c
[ 779.044787] ? string+0xab/0x180
[ 779.044792] ? string+0xab/0x180
[ 779.044797] kasan_report.cold.3+0x1a/0x32
[ 779.044803] ? string+0xab/0x180
[ 779.044809] string+0xab/0x180
[ 779.044816] ? widen_string+0x160/0x160
[ 779.044822] ? vsnprintf+0x5bf/0x7f0
[ 779.044829] vsnprintf+0x4e7/0x7f0
[ 779.044836] ? pointer+0x4a0/0x4a0
[ 779.044841] ? seq_buf_vprintf+0x79/0xc0
[ 779.044848] seq_buf_vprintf+0x62/0xc0
[ 779.044855] trace_seq_printf+0x113/0x210
[ 779.044861] ? trace_seq_puts+0x110/0x110
[ 779.044867] ? trace_raw_output_prep+0xd8/0x110
[ 779.044876] trace_raw_output_smb3_tcon_class+0x9f/0xc0
[ 779.044882] print_trace_line+0x377/0x890
[ 779.044888] ? tracing_buffers_read+0x300/0x300
[ 779.044893] ? ring_buffer_read+0x58/0x70
[ 779.044899] s_show+0x6e/0x140
[ 779.044906] seq_read+0x505/0x6a0
[ 779.044913] vfs_read+0xaf/0x1b0
[ 779.044919] ksys_read+0xa1/0x130
[ 779.044925] ? kernel_write+0xa0/0xa0
[ 779.044931] ? __do_page_fault+0x3d5/0x620
[ 779.044938] do_syscall_64+0x63/0x150
[ 779.044944] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 779.044949] RIP: 0033:0x7f62c2c2db31
[ 779.044955] Code: fe ff ff 48 8d 3d 17 9e 09 00 48 83 ec 08 e8 96 02
02 00 66 0f 1f 44 00 00 8b 05 fa fc 2c 00 48 63 ff 85 c0 75 13 31 c0
0f 05 <48> 3d 00 f0 ff ff 77 57 f3 c3 0f 1f 44 00 00 55 53 48 89 d5 48
89
[ 779.044958] RSP: 002b:
00007ffd6e116678 EFLAGS:
00000246 ORIG_RAX:
0000000000000000
[ 779.044964] RAX:
ffffffffffffffda RBX:
0000560a38be9260 RCX:
00007f62c2c2db31
[ 779.044966] RDX:
0000000000002000 RSI:
00007ffd6e116710 RDI:
0000000000000003
[ 779.044966] RDX:
0000000000002000 RSI:
00007ffd6e116710 RDI:
0000000000000003
[ 779.044969] RBP:
00007f62c2ef5420 R08:
0000000000000000 R09:
0000000000000003
[ 779.044972] R10:
ffffffffffffffa8 R11:
0000000000000246 R12:
00007ffd6e116710
[ 779.044975] R13:
0000000000002000 R14:
0000000000000d68 R15:
0000000000002000
[ 779.044981] Allocated by task 1257:
[ 779.044987] __kasan_kmalloc.constprop.5+0xc1/0xd0
[ 779.044992] kmem_cache_alloc+0xad/0x1a0
[ 779.044997] getname_flags+0x6c/0x2a0
[ 779.045003] user_path_at_empty+0x1d/0x40
[ 779.045008] do_faccessat+0x12a/0x330
[ 779.045012] do_syscall_64+0x63/0x150
[ 779.045017] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 779.045019] Freed by task 1257:
[ 779.045023] __kasan_slab_free+0x12e/0x180
[ 779.045029] kmem_cache_free+0x85/0x1b0
[ 779.045034] filename_lookup.part.70+0x176/0x250
[ 779.045039] do_faccessat+0x12a/0x330
[ 779.045043] do_syscall_64+0x63/0x150
[ 779.045048] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 779.045052] The buggy address belongs to the object at
ffff88814f326600
which belongs to the cache names_cache of size 4096
[ 779.045057] The buggy address is located 872 bytes to the right of
4096-byte region [
ffff88814f326600,
ffff88814f327600)
[ 779.045058] The buggy address belongs to the page:
[ 779.045062] page:
ffffea00053cc800 count:1 mapcount:0 mapping:
ffff88815b191b40 index:0x0 compound_mapcount: 0
[ 779.045067] flags: 0x200000000010200(slab|head)
[ 779.045075] raw:
0200000000010200 dead000000000100 dead000000000200 ffff88815b191b40
[ 779.045081] raw:
0000000000000000 0000000000070007 00000001ffffffff 0000000000000000
[ 779.045083] page dumped because: kasan: bad access detected
[ 779.045085] Memory state around the buggy address:
[ 779.045089]
ffff88814f327800: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 779.045093]
ffff88814f327880: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 779.045097] >
ffff88814f327900: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 779.045099] ^
[ 779.045103]
ffff88814f327980: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 779.045107]
ffff88814f327a00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 779.045109] ==================================================================
[ 779.045110] Disabling lock debugging due to kernel taint
Correctly assign tree name str for smb3_tcon event.
Signed-off-by: Paulo Alcantara (SUSE) <paulo@paulo.ac>
Signed-off-by: Steve French <stfrench@microsoft.com>
Ronnie Sahlberg [Thu, 21 Mar 2019 04:59:02 +0000 (14:59 +1000)]
cifs: allow guest mounts to work for smb3.11
Fix Guest/Anonymous sessions so that they work with SMB 3.11.
The commit noted below tightened the conditions and forced signing for
the SMB2-TreeConnect commands as per MS-SMB2.
However, this should only apply to normal user sessions and not for
Guest/Anonumous sessions.
Fixes:
6188f28bf608 ("Tree connect for SMB3.1.1 must be signed for non-encrypted shares")
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Steve French [Sun, 17 Mar 2019 20:58:38 +0000 (15:58 -0500)]
fix incorrect error code mapping for OBJECTID_NOT_FOUND
It was mapped to EIO which can be confusing when user space
queries for an object GUID for an object for which the server
file system doesn't support (or hasn't saved one).
As Amir Goldstein suggested this is similar to ENOATTR
(equivalently ENODATA in Linux errno definitions) so
changing NT STATUS code mapping for OBJECTID_NOT_FOUND
to ENODATA.
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Amir Goldstein <amir73il@gmail.com>
Xiaoli Feng [Sat, 16 Mar 2019 04:11:54 +0000 (12:11 +0800)]
cifs: fix that return -EINVAL when do dedupe operation
dedupe_file_range operations is combiled into remap_file_range.
But it's always skipped for dedupe operations in function
cifs_remap_file_range.
Example to test:
Before this patch:
# dd if=/dev/zero of=cifs/file bs=1M count=1
# xfs_io -c "dedupe cifs/file 4k 64k 4k" cifs/file
XFS_IOC_FILE_EXTENT_SAME: Invalid argument
After this patch:
# dd if=/dev/zero of=cifs/file bs=1M count=1
# xfs_io -c "dedupe cifs/file 4k 64k 4k" cifs/file
XFS_IOC_FILE_EXTENT_SAME: Operation not supported
Influence for xfstests:
generic/091
generic/112
generic/127
generic/263
These tests report this error "do_copy_range:: Invalid
argument" instead of "FIDEDUPERANGE: Invalid argument".
Because there are still two bugs cause these test failed.
https://bugzilla.kernel.org/show_bug.cgi?id=202935
https://bugzilla.kernel.org/show_bug.cgi?id=202785
Signed-off-by: Xiaoli Feng <fengxiaoli0714@gmail.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Long Li [Fri, 15 Mar 2019 07:55:00 +0000 (07:55 +0000)]
CIFS: Fix an issue with re-sending rdata when transport returning -EAGAIN
When sending a rdata, transport may return -EAGAIN. In this case
we should re-obtain credits because the session may have been
reconnected.
Change in v2: adjust_credits before re-sending
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Long Li [Fri, 15 Mar 2019 07:54:59 +0000 (07:54 +0000)]
CIFS: Fix an issue with re-sending wdata when transport returning -EAGAIN
When sending a wdata, transport may return -EAGAIN. In this case
we should re-obtain credits because the session may have been
reconnected.
Change in v2: adjust_credits before re-sending
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
YueHaibing [Fri, 22 Mar 2019 14:43:59 +0000 (22:43 +0800)]
clocksource/drivers/mips-gic-timer: Make gic_compare_irqaction static
Fix sparse warning:
drivers/clocksource/mips-gic-timer.c:70:18: warning:
symbol 'gic_compare_irqaction' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <daniel.lezcano@linaro.org>
Link: https://lkml.kernel.org/r/20190322144359.19516-1-yuehaibing@huawei.com
YueHaibing [Fri, 22 Mar 2019 14:43:02 +0000 (22:43 +0800)]
clocksource/drivers/timer-ti-dm: Make omap_dm_timer_set_load_start() static
Fix sparse warning:
drivers/clocksource/timer-ti-dm.c:589:5: warning:
symbol 'omap_dm_timer_set_load_start' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <daniel.lezcano@linaro.org>
Link: https://lkml.kernel.org/r/20190322144302.6704-1-yuehaibing@huawei.com
YueHaibing [Fri, 22 Mar 2019 14:39:40 +0000 (22:39 +0800)]
clocksource/drivers/tcb_clksrc: Make tc_clksrc_suspend/resume() static
Fix sparse warnings:
drivers/clocksource/tcb_clksrc.c:74:6: warning:
symbol 'tc_clksrc_suspend' was not declared. Should it be static?
drivers/clocksource/tcb_clksrc.c:89:6: warning:
symbol 'tc_clksrc_resume' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <nicolas.ferre@microchip.com>
Cc: <daniel.lezcano@linaro.org>
Cc: <linux-arm-kernel@lists.infradead.org>
Link: https://lkml.kernel.org/r/20190322143940.12396-1-yuehaibing@huawei.com
YueHaibing [Fri, 22 Mar 2019 14:37:08 +0000 (22:37 +0800)]
clocksource/drivers/clps711x: Make clps711x_clksrc_init() static
Fix sparse warning:
drivers/clocksource/clps711x-timer.c:96:13: warning:
symbol 'clps711x_clksrc_init' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <daniel.lezcano@linaro.org>
Cc: <shc_work@mail.ru>
Cc: <linux-arm-kernel@lists.infradead.org>
Link: https://lkml.kernel.org/r/20190322143708.12716-1-yuehaibing@huawei.com
Thomas Gleixner [Fri, 22 Mar 2019 21:51:21 +0000 (22:51 +0100)]
Merge tag 'perf-core-for-mingo-5.1-
20190321' of git://git./linux/kernel/git/acme/linux into perf/urgent
Pull perf/core improvements and fixes from Arnaldo:
BPF:
Song Liu:
- Add support for annotating BPF programs, using the PERF_RECORD_BPF_EVENT
and PERF_RECORD_KSYMBOL recently added to the kernel and plugging
binutils's libopcodes disassembly of BPF programs with the existing
annotation interfaces in 'perf annotate', 'perf report' and 'perf top'
various output formats (--stdio, --stdio2, --tui).
perf list:
Andi Kleen:
- Filter metrics when using substring search.
perf record:
Andi Kleen:
- Allow to limit number of reported perf.data files
- Clarify help for --switch-output.
perf report:
Andi Kleen
- Indicate JITed code better.
- Show all sort keys in help output.
perf script:
Andi Kleen:
- Support relative time.
perf stat:
Andi Kleen:
- Improve scaling.
General:
Changbin Du:
- Fix some mostly error path memory and reference count leaks found
using gcc's ASan and UBSan.
Vendor events:
Mamatha Inamdar:
- Remove P8 HW events which are not supported.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Fri, 22 Mar 2019 21:50:41 +0000 (22:50 +0100)]
Merge tag 'perf-core-for-mingo-5.1-
20190311' of git://git./linux/kernel/git/acme/linux into perf/urgent
Pull perf/core improvements and fixes from Arnaldo:
kernel:
Stephane Eranian :
- Restore mmap record type correctly when handling PERF_RECORD_MMAP2
events, as the same template is used for all the threads interested
in mmap events, some may want just PERF_RECORD_MMAP, while some
may want the extra info in MMAP2 records.
perf probe:
Adrian Hunter:
- Fix getting the kernel map, because since changes related to x86 PTI
entry trampolines handling, there are more than one kernel map.
perf script:
Andi Kleen:
- Support insn output for normal samples, i.e.:
perf script -F ip,sym,insn --xed
Will fetch the sample IP from the thread address space and feed it
to Intel's XED disassembler, producing lines such as:
ffffffffa4068804 native_write_msr wrmsr
ffffffffa415b95e __hrtimer_next_event_base movq 0x18(%rax), %rdx
That match 'perf annotate's output.
- Make the --cpu filter apply to PERF_RECORD_COMM/FORK/... events, in
addition to PERF_RECORD_SAMPLE.
perf report:
- Add a new --samples option to save a small random number of samples
per hist entry, using a reservoir technique to select a representative
number of samples.
Then allow browsing the samples using 'perf script' as part of the hist
entry context menu. This automatically adds the right filters, so only
the thread or CPU of the sample is displayed. Then we use less' search
functionality to directly jump to the time stamp of the selected sample.
It uses different menus for assembler and source display. Assembler
needs xed installed and source needs debuginfo.
- Fix the UI browser scripts pop up menu when there are many scripts
available.
perf report:
Andi Kleen:
- Add 'time' sort option. E.g.:
% perf report --sort time,overhead,symbol --time-quantum 1ms --stdio
...
0.67% 277061.87300 [.] _dl_start
0.50% 277061.87300 [.] f1
0.50% 277061.87300 [.] f2
0.33% 277061.87300 [.] main
0.29% 277061.87300 [.] _dl_lookup_symbol_x
0.29% 277061.87300 [.] dl_main
0.29% 277061.87300 [.] do_lookup_x
0.17% 277061.87300 [.] _dl_debug_initialize
0.17% 277061.87300 [.] _dl_init_paths
0.08% 277061.87300 [.] check_match
0.04% 277061.87300 [.] _dl_count_modids
1.33% 277061.87400 [.] f1
1.33% 277061.87400 [.] f2
1.33% 277061.87400 [.] main
1.17% 277061.87500 [.] main
1.08% 277061.87500 [.] f1
1.08% 277061.87500 [.] f2
1.00% 277061.87600 [.] main
0.83% 277061.87600 [.] f1
0.83% 277061.87600 [.] f2
1.00% 277061.87700 [.] main
tools headers:
Arnaldo Carvalho de Melo:
- Update x86's syscall_64.tbl, no change in tools/perf behaviour.
- Sync copies asm-generic/unistd.h and linux/in with the kernel sources.
perf data:
Jiri Olsa:
- Prep work to support having perf.data stored as a directory, with one
file per CPU, that ultimately will allow having one ring buffer reading
thread per CPU.
Vendor events:
Martin Liška:
- perf PMU events for AMD Family 17h.
perf script python:
Tony Jones:
- Add python3 support for the remaining Intel PT related scripts, with
these we should have a clean build of perf with python3 while still
supporting the build with python2.
libbpf:
Arnaldo Carvalho de Melo:
- Fix the build on uCLibc, adding the missing stdarg.h since we use
va_list in one typedef.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Linus Torvalds [Fri, 22 Mar 2019 21:15:11 +0000 (14:15 -0700)]
Merge tag 'powerpc-5.1-3' of git://git./linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"One fix for a boot failure on 32-bit, introduced during the merge
window.
A fix for our handling of CLOCK_MONOTONIC in the 64-bit VDSO. Changing
the wall clock across the Y2038 boundary could cause CLOCK_MONOTONIC
to jump forward and backward.
Our spectre_v2 reporting was a bit confusing due to a bug I
introduced. On some systems it was reporting that the count cache was
disabled and also that we were flushing the count cache on context
switch. Only the former is true, and given that the count cache is
disabled it doesn't make any sense to flush it. No one reported it, so
presumably the presence of any mitigation is all people check for.
Finally a small build fix for zsmalloc on 32-bit.
Thanks to: Ben Hutchings, Christophe Leroy, Diana Craciun, Guenter
Roeck, Michael Neuling"
* tag 'powerpc-5.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/security: Fix spectre_v2 reporting
powerpc/mm: Only define MAX_PHYSMEM_BITS in SPARSEMEM configurations
powerpc/6xx: fix setup and use of SPRN_SPRG_PGDIR for hash32
powerpc/vdso64: Fix CLOCK_MONOTONIC inconsistencies across Y2038
Linus Torvalds [Fri, 22 Mar 2019 21:10:27 +0000 (14:10 -0700)]
Merge tag 'iommu-fixes-v5.1-rc2' of git://git./linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
- AMD IOMMU fix for sg-mapping with sg->offset > PAGE_SIZE
- Fix for IOVA code to trigger the slow-path less often
- Two fixes for Intel VT-d to avoid writing to read-only registers and
to flush the right domain id for the default domains in scalable mode
* tag 'iommu-fixes-v5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/vt-d: Save the right domain ID used by hardware
iommu/vt-d: Check capability before disabling protected memory
iommu/iova: Fix tracking of recently failed iova address
iommu/amd: fix sg->dma_address for sg->offset bigger than PAGE_SIZE
Linus Torvalds [Fri, 22 Mar 2019 21:04:38 +0000 (14:04 -0700)]
Merge tag 'sound-5.1-rc2' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"The only significant change is the regression fixes for the jack
detection at resume on HD-audio, while others are all small or trivial
fixes like the coverage of missing error code or usual HD-audio quirk"
* tag 'sound-5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek: Enable headset MIC of Acer AIO with ALC286
ALSA: hda - Enforces runtime_resume after S3 and S4 for each codec
ALSA: hda - Don't trigger jackpoll_work in azx_resume
ALSA: opl3: fix mismatch between snd_opl3_drum_switch definition and declaration
ALSA: hda - add Lenovo IdeaCentre B550 to the power_save_blacklist
ALSA: firewire-motu: use 'version' field of unit directory to identify model
ALSA: sb8: add a check for request_region
ALSA: echoaudio: add a check for ioremap_nocache
Linus Torvalds [Fri, 22 Mar 2019 19:08:52 +0000 (12:08 -0700)]
Merge tag 'devprop-5.1-rc2' of git://git./linux/kernel/git/rafael/linux-pm
Pull device properties framework fix from Rafael Wysocki:
"Add missing 'static' in two places (YueHaibing)"
* tag 'devprop-5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
drivers: base: swnode: Make two functions static
Linus Torvalds [Fri, 22 Mar 2019 19:07:06 +0000 (12:07 -0700)]
Merge tag 'acpi-5.1-rc2' of git://git./linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Prevent device references acquired by bus_find_device() in
acpi_dev_present() from being leaked (Andy Shevchenko)"
* tag 'acpi-5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / utils: Drop reference in test for device presence
Linus Torvalds [Fri, 22 Mar 2019 19:03:19 +0000 (12:03 -0700)]
Merge tag 'pm-5.1-rc2' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These rearrange some code in the generic power domains (genpd)
framework to avoid a potential deadlock and make the turbostat utility
behave more as expected.
Specifics:
- Rearrange the generic power domains (genpd) code to avoid a
potential deadlock possible due to its interactions with the clock
framework (Jiada Wang)
- Make turbostat return the exit status of the command run under it
if that command fails (David Arcari)"
* tag 'pm-5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / Domains: Avoid a potential deadlock
tools/power turbostat: return the exit status of a command
Linus Torvalds [Fri, 22 Mar 2019 18:26:57 +0000 (11:26 -0700)]
Merge tag 'mmc-v5.1-rc1' of git://git./linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"A couple of MMC host fixes intended for v5.1:
- alcor: Fix DMA reads
- renesas_sdhi: Limit block count to 16-bit for old revisions
- sdhci-omap: Fixup support for read-only pins
- mxcmmc: Revert support for highmem pages
- davinci/pxamci: Fix clang build warnings"
* tag 'mmc-v5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: renesas_sdhi: limit block count to 16 bit for old revisions
mmc: alcor: fix DMA reads
mmc: sdhci-omap: Set caps2 to indicate no physical write protect pin
mmc: mxcmmc: "Revert mmc: mxcmmc: handle highmem pages"
mmc: davinci: remove extraneous __init annotation
mmc: pxamci: fix enum type confusion
Shenghui Wang [Sat, 16 Mar 2019 08:24:37 +0000 (16:24 +0800)]
sbitmap: trivial - update comment for sbitmap_deferred_clear_bit
"sbitmap_batch_clear" should be "sbitmap_deferred_clear"
Acked-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Shenghui Wang <shhuiw@foxmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Thomas Gleixner [Fri, 22 Mar 2019 16:09:59 +0000 (17:09 +0100)]
Merge branch 'x86/cpu' into x86/urgent
Merge the forgotten cleanup patch for the new file, so the mess does not
propagate further.
Nathan Chancellor [Thu, 7 Mar 2019 21:27:56 +0000 (14:27 -0700)]
x86/hw_breakpoints: Make default case in hw_breakpoint_arch_parse() return an error
When building with -Wsometimes-uninitialized, Clang warns:
arch/x86/kernel/hw_breakpoint.c:355:2: warning: variable 'align' is used
uninitialized whenever switch default is taken
[-Wsometimes-uninitialized]
The default cannot be reached because arch_build_bp_info() initializes
hw->len to one of the specified cases. Nevertheless the warning is valid
and returning -EINVAL makes sure that this cannot be broken by future
modifications.
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: clang-built-linux@googlegroups.com
Link: https://github.com/ClangBuiltLinux/linux/issues/392
Link: https://lkml.kernel.org/r/20190307212756.4648-1-natechancellor@gmail.com
Heiner Kallweit [Thu, 21 Mar 2019 20:23:14 +0000 (21:23 +0100)]
r8169: don't read interrupt mask register in interrupt handler
After the original patch network starts to crash on heavy load.
It's not fully clear why this additional register read has such side
effects, but removing it fixes the issue.
Thanks also to Alex for his contribution and hints.
[0] https://marc.info/?t=
155268170400002&r=1&w=2
Fixes:
e782410ed237 ("r8169: improve spurious interrupt detection")
Reported-by: VDR User <user.vdr@gmail.com>
Tested-by: VDR User <user.vdr@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Valdis Kletnieks [Tue, 12 Mar 2019 09:33:48 +0000 (05:33 -0400)]
watchdog/core: Make variables static
sparse complains:
CHECK kernel/watchdog.c
kernel/watchdog.c:45:19: warning: symbol 'nmi_watchdog_available'
was not declared. Should it be static?
kernel/watchdog.c:47:16: warning: symbol 'watchdog_allowed_mask'
was not declared. Should it be static?
They're not referenced by name from anyplace else, make them static.
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/7855.1552383228@turing-police
Valdis Kletnieks [Tue, 12 Mar 2019 08:38:35 +0000 (04:38 -0400)]
time/jiffies: Make refined_jiffies static
sparse complains:
CHECK kernel/time/jiffies.c
kernel/time/jiffies.c:92:20: warning: symbol 'refined_jiffies' was not
declared. Should it be static?
Its only used in file scope. Make it static.
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/32342.1552379915@turing-police
Valdis Kletnieks [Tue, 12 Mar 2019 08:17:56 +0000 (04:17 -0400)]
genirq/devres: Remove excess parameter from kernel doc
Building with 'make W=1' complains:
CC kernel/irq/devres.o
kernel/irq/devres.c:104: warning: Excess function parameter 'thread_fn'
description in 'devm_request_any_context_irq'
Remove it.
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/31207.1552378676@turing-police
Valdis Kletnieks [Tue, 12 Mar 2019 07:47:53 +0000 (03:47 -0400)]
x86/mm/pti: Make local symbols static
With 'make C=2 W=1', sparse and gcc both complain:
CHECK arch/x86/mm/pti.c
arch/x86/mm/pti.c:84:3: warning: symbol 'pti_mode' was not declared. Should it be static?
arch/x86/mm/pti.c:605:6: warning: symbol 'pti_set_kernel_image_nonglobal' was not declared. Should it be static?
CC arch/x86/mm/pti.o
arch/x86/mm/pti.c:605:6: warning: no previous prototype for 'pti_set_kernel_image_nonglobal' [-Wmissing-prototypes]
605 | void pti_set_kernel_image_nonglobal(void)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
pti_set_kernel_image_nonglobal() is only used locally. 'pti_mode' exists in
drivers/hwtracing/intel_th/pti.c as well, but it's a completely unrelated
local (static) symbol.
Make both static.
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lkml.kernel.org/r/27680.1552376873@turing-police
Chen Jie [Fri, 15 Mar 2019 03:44:38 +0000 (03:44 +0000)]
futex: Ensure that futex address is aligned in handle_futex_death()
The futex code requires that the user space addresses of futexes are 32bit
aligned. sys_futex() checks this in futex_get_keys() but the robust list
code has no alignment check in place.
As a consequence the kernel crashes on architectures with strict alignment
requirements in handle_futex_death() when trying to cmpxchg() on an
unaligned futex address which was retrieved from the robust list.
[ tglx: Rewrote changelog, proper sizeof() based alignement check and add
comment ]
Fixes:
0771dfefc9e5 ("[PATCH] lightweight robust futexes: core")
Signed-off-by: Chen Jie <chenjie6@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <dvhart@infradead.org>
Cc: <peterz@infradead.org>
Cc: <zengweilin@huawei.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1552621478-119787-1-git-send-email-chenjie6@huawei.com
Lu Baolu [Wed, 20 Mar 2019 01:58:34 +0000 (09:58 +0800)]
iommu/vt-d: Save the right domain ID used by hardware
The driver sets a default domain id (FLPT_DEFAULT_DID) in the
first level only pasid entry, but saves a different domain id
in @sdev->did. The value saved in @sdev->did will be used to
invalidate the translation caches. Hence, the driver might
result in invalidating the caches with a wrong domain id.
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Fixes:
1c4f88b7f1f92 ("iommu/vt-d: Shared virtual address in scalable mode")
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>