arm64: dts: qcom: Fix sdhci node names - use 'mmc@'

Since the Qualcomm sdhci-msm device-tree binding has been converted
to yaml format, 'make dtbs_check' reports issues with
inconsistent 'sdhci@' convention used for specifying the
sdhci nodes. The generic mmc bindings expect 'mmc@' format
instead.

Fix the same.

Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
[bjorn: Moved non-arm64 changes to separate commit]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220514215424.1007718-2-bhupesh.sharma@linaro.org

arm64: dts: qcom: sdm630-nile: Add RGB status LED on the PM660L LPG

The entire Sony Nile and Ganges lineup utilize the first three channels
(the triled channels) of the LPG block for an RGB (battery) status and
notification indicator.

Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
[bjorn: Dropped #address/#size-cells]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220511190718.764445-4-marijn.suijten@somainline.org

arm64: dts: qcom: pm660l: Add LPG node

The Light Pulse Generator describes a hardware block responsible for
displaying colors and patterns on an RGB LED (usually used for [battery]
status and notifications), and drive PWM signals for general-purpose
(ie. backlight) LEDs.  The availability and usage of the individual
channels differ per board and is hence left for individual platform DTs
to configure.

Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
[bjorn: Dropped #address/size-cells]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220511190718.764445-3-marijn.suijten@somainline.org

arm64: dts: qcom: qcs404: fix default pinctrl settings for blsp1_spi1

The current settings refer to "blsp_spi1" function which isn't defined.
For this reason an attempt to enable blsp1_spi1 interface results in
the probe failure below:

[    3.492900] qcs404-pinctrl 1000000.pinctrl: invalid function blsp_spi1 in map table
[    3.502460] qcs404-pinctrl 1000000.pinctrl: invalid function blsp_spi1 in map table
[    3.517725] qcs404-pinctrl 1000000.pinctrl: invalid function blsp_spi1 in map table
[    3.532998] qcs404-pinctrl 1000000.pinctrl: invalid function blsp_spi1 in map table
[    3.548277] spi_qup: probe of 78b6000.spi failed with error -22

Fix this by making the functions used in qcs404.dtsi to match the contents
of drivers/pinctrl/qcom/pinctrl-qcs404.c.

Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220611195713.131597-1-andrey.konovalov@linaro.org

arm64: dts: qcom: qrb5165-rb5: declare tri-led user leds

Qualcomm RB5 platform uses Light Pulse Generator tri-led block to drive
three green leds. Add device nodes defining those leds.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220505145102.1432670-4-dmitry.baryshkov@linaro.org

arm64: dts: qcom: pm8150l: add Light Pulse Generator device node

Add device node defining LPG/PWM block on PM8150L PMIC chip.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220505145102.1432670-3-dmitry.baryshkov@linaro.org

arm64: dts: qcom: pm8150b: add Light Pulse Generator device node

Add device node defining LPG/PWM block on PM8150B PMIC chip.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220505145102.1432670-2-dmitry.baryshkov@linaro.org

arm64: dts: qcom: align led node names with dtschema

The node names should be generic and DT schema expects certain pattern
with 'led'.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220616005333.18491-24-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sdm630-sony-xperia-nile: drop unneeded status from gpio-keys

Nodes do not need explicit status=okay.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220616005333.18491-23-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: correct gpio-keys properties

gpio-keys children do not use unit addresses.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220616005333.18491-22-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: align gpio-key node names with dtschema

The node names should be generic and DT schema expects certain pattern
(e.g. with key/button/switch).

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220616005333.18491-21-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: adjust whitespace around '='

Fix whitespace coding style: use single space instead of tabs or
multiple spaces around '=' sign in property assignment.  No functional
changes (same DTB).

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220526204248.832139-1-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: msm8998-mtp: correct board compatible

Add qcom,msm8998 SoC fallback to the board compatible.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220521164550.91115-12-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: ipq6018-cp01-c1: fix Micron SPI NOR compatible

The proper compatible for Micron n25q128a11 SPI NOR flash should include
vendor-prefix.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220521164550.91115-11-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sdm630: correct QFPROM byte offsets

The NVMEM bindings expect that 'bits' property holds offset and size of
region within a byte, so it applies a constraint of <0, 7> for the
offset.  Using 25 as HSTX trim offset is within 4-byte QFPROM word, but
outside of the byte:

  sdm630-sony-xperia-nile-discovery.dtb: qfprom@780000: hstx-trim@240:bits:0:0: 25 is greater than the maximum of 7
  sdm630-sony-xperia-nile-discovery.dtb: qfprom@780000: gpu-speed-bin@41a0:bits:0:0: 21 is greater than the maximum of 7

Align the offsets to match the bindings.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220505113802.243301-6-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: use dedicated QFPROM compatibles

Use dedicated compatibles for QFPROM on MSM8916, MSM8996, MSM8998,
QCS404 and SDM630 which is expected by the bindings:

  msm8996-mtp.dtb: qfprom@74000: compatible:0: 'qcom,qfprom' is not one of ['qcom,apq8064-qfprom', ...

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220505113802.243301-5-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: correct SPMI WLED register range encoding

On PM660L, PMI8994 and PMI8998, the WLED has two address spaces and with
size-cells=0, they should be encoded as two separate items.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220505154702.422108-2-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: add missing AOSS QMP compatible fallback

The AOSS QMP bindings expect all compatibles to be followed by fallback
"qcom,aoss-qmp" because all of these are actually compatible with each
other.  This fixes dtbs_check warnings like:

  sm8250-hdk.dtb: power-controller@c300000: compatible: ['qcom,sm8250-aoss-qmp'] is too short

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220504131923.214367-6-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sc7180: Add kingoftown dts files

Kingoftown is a trogdor-based board. These dts files are unchanged copies
from the downstream Chrome OS 5.4 kernel.

Signed-off-by: Joseph S. Barrera III <joebar@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220625183538.v14.5.Ib62291487a664a65066d18a3e83c5428a6d2cc6c@changeid

arm64: dts: qcom: sc7180: Add pazquel dts files

Pazquel is a trogdor-based board. These dts files are unchanged copies
from the downstream Chrome OS 5.4 kernel.

Signed-off-by: Joseph S. Barrera III <joebar@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220625183538.v14.4.I41e2c2dc12961fe000ebc4d4ef6f0bc5da1259ea@changeid

arm64: dts: qcom: sc7180: Add mrbland dts files

Mrbland is a trogdor-based board. These dts files are copies from
the downstream Chrome OS 5.4 kernel, but with downstream bits removed.

Signed-off-by: Joseph S. Barrera III <joebar@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220625183538.v14.3.I71176ebf7e5aebddb211f00e805b32c08376d1be@changeid

arm64: dts: qcom: sc7180: Add quackingstick dts files

Quackingstick is a trogdor-based board. These dts files are copies from
the downstream Chrome OS 5.4 kernel, but with downstream bits removed.

Signed-off-by: Joseph S. Barrera III <joebar@chromium.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220625183538.v14.2.I0977b1a08830d0caa8bfb1bdedb4ecceac709a7f@changeid

arm64: dts: qcom: sc7180: Add wormdingler dts files

Wormdingler is a trogdor-based board, shipping to customers as the
Lenovo IdeaPad Chromebook Duet 3. These dts files are copies from
the downstream Chrome OS 5.4 kernel, but with the camera
(sc7180-trogdor-mipi-camera.dtsi) #include removed.

Signed-off-by: Joseph S. Barrera III <joebar@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220625183538.v14.1.Id769ddc5dbf570ccb511db96da59f97d08f75a9c@changeid

arm64: dts: qcom: sc7280: Rename sar sensor labels

To ease matching configuration of sysfs attributes for particular
sensor, match label reported by iio 'label' attribute with the location
label generated by ChromeOS config tool.

Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220623223119.1858863-1-gwendal@chromium.org

arm64: dts: qcom: sc8280xp: add Lenovo Thinkpad X13s devicetree

Add an initial devicetree for the Lenovo Thinkpad X13s with support for
USB, backlight, keyboard, touchpad, touchscreen (to be verified), PMICs
and remoteprocs.

Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220622132617.24604-1-johan+linaro@kernel.org

arm64: dts: qcom: add SA8540P and ADP

Introduce the Qualcomm SA8540P automotive platform and the SA8295P ADP
development board.

The SA8540P and SC8280XP are fairly similar, so the SA8540P is built
ontop of the SC8280XP dtsi to reduce duplication. As more advanced
features are integrated this might be re-evaluated.

This initial contribution supports SMP, CPUFreq, cluster idle, UFS, RPMh
regulators, debug UART, PMICs, remoteprocs (NSPs crashes shortly after
booting) and USB.

The SA8295P ADP contains four PM8450 PMICs, which according to their
revid are compatible with PM8150. They are defined within the ADP for
now, to avoid creating additional .dtsi files for PM8150 with just
addresses changed - and to allow using the labels from the schematics.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220629041438.1352536-6-bjorn.andersson@linaro.org

arm64: dts: qcom: sc8280xp: Add reference device

Add basic support for the SC8280XP reference device, which allows it to
boot to a shell (using EFIFB) with functional storage (UFS), USB,
keyboard, touchpad, touchscreen, backlight and remoteprocs.

The PMICs are, per socinfo, reused from other platforms. But given that
the address of the PMICs doesn't match other cases and that it's
desirable to label things according to the schematics a new dtsi file is
created to represent the reference combination of PMICs.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220629041438.1352536-5-bjorn.andersson@linaro.org

arm64: dts: qcom: add SC8280XP platform

Introduce initial support for the Qualcomm SC8280XP platform, aka 8cx
Gen 3. This initial contribution supports SMP, CPUfreq, CPU cluster
idling, GCC, TLMM, SMMU, RPMh regulators, power-domains and clocks,
interconnects, some QUPs, UFS, remoteprocs, USB, watchdog, LLCC and
tsens.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220629041438.1352536-4-bjorn.andersson@linaro.org

dt-bindings: mailbox: qcom-ipcc: Add NSP1 client

Add a client for the NSP1 found in some recent Qualcomm platforms.

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220629041438.1352536-3-bjorn.andersson@linaro.org

dt-bindings: arm: qcom: Document additional sc8280xp devices

Add the CRD (Compute Reference Design?) and the Lenovo Thinkpad X13s to
the valid device compatibles found on the sc8280xp platform.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220629041438.1352536-2-bjorn.andersson@linaro.org

arm64: dts: qcom: sm8450: Add interconnect requirements for SCM

Add interconnects requirements for the SCM interface on SM8450 SoCs.

Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1653289258-17699-4-git-send-email-quic_sibis@quicinc.com

arm64: dts: qcom: sdm660: Add initial Inforce IFC6560 board support

The IFC6560 is a board from Inforce Computing, built around the SDA660
SoC. This patch describes core clocks, some regulators from the two
PMICs, debug uart, storage, bluetooth and audio DSP remoteproc.

The regulator settings are inherited from prior work by Konrad Dybcio
and AngeloGioacchino Del Regno.

Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Co-developed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220521202708.1509308-12-dmitry.baryshkov@linaro.org

dt-bindings: arm: qcom: document sda660 SoC and ifc6560 board

Add binding documentation for the Inforce IFC6560 board which uses
Snapdragon SDA660.

Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220521202708.1509308-11-dmitry.baryshkov@linaro.org

arm64: dts: qcom: sdm660: move SDHC2 card detect pinconf to board files

This results in dts duplication, but per mutual agreement card detect
pin configuration belongs to the board files. Move it from the SoC
dtsi to the board DT files.

Suggested-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220521202708.1509308-10-dmitry.baryshkov@linaro.org

arm64: dts: qcom: sdm636-sony-xperia-ganges-mermaid: correct sdc2 pinconf

Fix the device tree node in the &sdc2_state_on override. The sdm630 uses
'clk' rather than 'pinconf-clk'.

Fixes: 4c1d849ec047 ("arm64: dts: qcom: sdm630-xperia: Retire sdm630-sony-xperia-ganges.dtsi")
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220521202708.1509308-9-dmitry.baryshkov@linaro.org

arm64: dts: qcom: sdm630: fix gpu's interconnect path

ICC path for the GPU incorrectly states <&gnoc 1 &bimc 5>, which is
a path from SLAVE_GNOC_BIMC to SLAVE_EBI. According to the downstream
kernel sources, the GPU uses MASTER_OXILI here, which is equivalent to
<&bimc 1 ...>.

While we are at it, use defined names instead of the numbers for this
interconnect path.

Fixes: 5cf69dcbec8b ("arm64: dts: qcom: sdm630: Add Adreno 508 GPU configuration")
Reported-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220521202708.1509308-8-dmitry.baryshkov@linaro.org

arm64: dts: qcom: sdm630: add second (HS) USB host support

Add DT entries for the second DWC3 USB host, which is limited to the
USB2.0 (HighSpeed), and the corresponding QUSB PHY.

Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220521202708.1509308-7-dmitry.baryshkov@linaro.org

arm64: dts: qcom: sdm630: rename qusb2phy to qusb2phy0

In preparation to adding second USB host/PHY pair, change first USB
PHY's label to qusb2phy0.

Suggested-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220521202708.1509308-6-dmitry.baryshkov@linaro.org

arm64: dts: qcom: sdm630: fix the qusb2phy ref clock

According to the downstram DT file, the qusb2phy ref clock should be
GCC_RX0_USB2_CLKREF_CLK, not GCC_RX1_USB2_CLKREF_CLK.

Fixes: c65a4ed2ea8b ("arm64: dts: qcom: sdm630: Add USB configuration")
Cc: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220521202708.1509308-5-dmitry.baryshkov@linaro.org

arm64: dts: qcom: sdm630: disable GPU by default

The SoC's device tree file disables gpucc and adreno's SMMU by default.
So let's disable the GPU too. Moreover it looks like SMMU might be not
usable without additional patches (which means that GPU is unusable
too). No board uses GPU at this moment.

Fixes: 5cf69dcbec8b ("arm64: dts: qcom: sdm630: Add Adreno 508 GPU configuration")
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220521202708.1509308-4-dmitry.baryshkov@linaro.org

arm64: dts: qcom: sdm660: disable dsi1/dsi1_phy by default

Follow the typical practice and keep DSI1/DSI1 PHY disabled by default.
They should be enabled in the board DT files. No existing boards use
them at this moment.

Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220521202708.1509308-3-dmitry.baryshkov@linaro.org

arm64: dts: qcom: sdm630: disable dsi0/dsi0_phy by default

Follow the typical practice and keep DSI0/DSI0 PHY disabled by default.
They should be enabled in the board DT files. No existing boards use
them at this moment.

Suggested-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220521202708.1509308-2-dmitry.baryshkov@linaro.org

arm64: dts: qcom: correct interrupt controller on PM8916 and PMS405

The PM8916 and PMS405 PMIC GPIOs are interrupt controllers, as described
in the bindings and used by the driver.  Drop the interrupts (apparently
copied from downstream tree), just like in commit 61d2ca503d0b ("arm64:
dts: qcom: fix pm8150 gpio interrupts"):

  qcs404-evb-4000.dtb: gpio@c000: 'interrupts' does not match any of the regexes: '-state$', 'pinctrl-[0-9]+'
  qcs404-evb-4000.dtb: gpio@c000: 'interrupt-controller' is a required property

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220508135932.132378-4-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: add missing gpio-ranges in PMIC GPIOs

The new Qualcomm PMIC GPIO bindings require gpio-ranges property:

  sm8250-sony-xperia-edo-pdx203.dtb: gpio@c000: 'gpio-ranges' is a required property

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220508135932.132378-3-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sdm630: order interrupts according to bindings

The CAMSS DTSI device node, which came after the bindings were merged,
got the interrupts ordered differently then specified in the bindings:

  sdm630-sony-xperia-nile-pioneer.dtb: camss@ca00000: interrupt-names:0: 'csid0' was expected

Reordering them to match bindings should not cause ABI issues, because
the driver relies on names, not ordering.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220509144714.144154-4-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sdm630: order regs according to bindings

The CAMSS DTSI device node, which came after the bindings were merged,
got the regs ordered differently then specified in the bindings:

  sdm636-sony-xperia-ganges-mermaid.dtb: camss@ca00000: reg-names:0: 'csi_clk_mux' was expected

Reordering them to match bindings should not cause ABI issues, because
the driver relies on names, not ordering.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220509144714.144154-3-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sdm630: order clocks according to bindings

The CAMSS DTSI device node, which came after the bindings were merged,
got the clocks ordered differently then specified in the bindings:

  sdm636-sony-xperia-ganges-mermaid.dtb: camss@ca00000: reg-names:4: 'csid3' was expected

Reordering them to match bindings should not cause ABI issues, because
the driver relies on names, not ordering.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220509144714.144154-2-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: msm8994-msft-lumia-octagon: add PM8994 pin properties

The bindings require that every pin configuration comes with 'function'
property.  There is also no 'drive-strength' property but
'qcom,drive-strength':

  msm8994-msft-lumia-octagon-cityman.dtb: gpios@c000: amsel-high-state: 'oneOf' conditional failed, one must be fixed:
    'drive-strength' does not match any of the regexes: 'pinctrl-[0-9]+'
    'bias-pull-up', 'drive-strength', 'function', 'pins' do not match any of the regexes: '(pinconf|-pins)$', 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220507194913.261121-9-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: apq8096-db820c: add PM8994 pin function

The bindings require that every pin configuration comes with 'function'
property.  Add such to PM8994 GPIO5.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220507194913.261121-8-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: add fallback compatible to PMIC GPIOs

The bindings require all PMIC GPIO nodes to have two compatibles -
specific followed by SPMI or SSBI fallback.  Add the fallback to fix
warnings like:

  msm8916-samsung-serranove.dtb: gpios@c000: compatible: ['qcom,pm8916-gpio'] is too short

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220507194913.261121-7-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: align PMIC GPIO pin configuration with DT schema

DT schema expects PMIC GPIO pin configuration nodes to be named with
'-state' suffix.  Optional children should be either 'pinconf' or
followed with '-pins' suffix.  This fixes dtbs_check warnings like:

  sdm845-xiaomi-beryllium.dtb: gpios@c000: 'vol-up-active' does not match any of the regexes: '-state$', 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220507194913.261121-6-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sdm845-akatsuki: Round down l22a regulator voltage

2700000 is not a multiple of pmic4_pldo's step size of 8000 (with base
voltage 1664000), resulting in pm8998-rpmh-regulators not probing.  Just
as we did with MSM8998's Sony Yoshino Poplar [1], round the voltages
down to err on the cautious side and leave a comment in place to
document this discrepancy wrt downstream sources.

[1]: https://lore.kernel.org/linux-arm-msm/20220507153627.1478268-1-marijn.suijten@somainline.org/

Fixes: 30a7f99befc6 ("arm64: dts: qcom: Add support for SONY Xperia XZ2 / XZ2C / XZ3 (Tama platform)")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220620211212.269956-1-marijn.suijten@somainline.org

arm64: dts: qcom: msm8996: Add SDHCI resets

On MSM8996, the default bootloader configuration leaves the hosts in some
weird state that never allows them to function properly under Linux.
Add the hardware resets so that we can start clean and get them actually
working.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220430162642.608106-1-konrad.dybcio@somainline.org

arm64: dts: qcom: msm8996-tone: Rule out PM(I)8994 variants

It looks like all Tone devices out in the wild are using PMI8996, which
suggests the PMI8994-variant DTs are not needed. Remove them.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220430162525.607946-1-konrad.dybcio@somainline.org

arm64: dts: qcom: msm8996-tone: Drop cont_splash_mem region

Tone does not have a functioning bootloader framebuffer and Linux allocates
the DRM framebuffer dynamically. Free up 36 MiB of precious RAM by removing
this reservation.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220430162319.607629-1-konrad.dybcio@somainline.org

arm64: dts: qcom: msm8998-mtp: Merge and fix up the DT

Merge the two DT files into one, sort the nodes and fix up a couple of style
incoherencies by adding some newlines, removing some, sorting properties etc.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220430162353.607709-14-konrad.dybcio@somainline.org

arm64: dts: qcom: msm8998-fxtec: Decouple from 8998 MTP

While the Pro-1 is based on MTP and is very close to it, it's really not great
for it to include the MTP dtsi straight up, as any small change will affect
both boards and not all of them will apply to the phone as well.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220430162353.607709-13-konrad.dybcio@somainline.org

arm64: dts: qcom: msm8998*: Clean up #includes

Sort the includes and remove unused ones.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220430162353.607709-12-konrad.dybcio@somainline.org

arm64: dts: qcom: msm8998-oneplus: Add clocks & GDSC to simplefb

This is required to keep the display working with MMCC enabled until proper
panel support is in place.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220430162353.607709-11-konrad.dybcio@somainline.org

arm64: dts: qcom: msm8998*: Keep MMCC & MMSS_SMMU enabled by default

MMCC is a component of the SoC that should always be configured. It was kept
off due to misconfiguration on clamshell machines. Keep it disabled on these
ones and enable it by default on all the others.

Exactly the same story applies to MMSS_SMMU, which directly depends on MMCC.

Do note, that if a platform doesn't use neither EFIFB (only applies to WoA
devices in this case) or simplefb (applies to precisely 2 msm8998 devices
as of this commit), this will not cause any harm.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220430162353.607709-10-konrad.dybcio@somainline.org

arm64: dts: qcom: msm8998-fxtec: Use "okay" instead of "ok"

This is the standard way.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220430162353.607709-9-konrad.dybcio@somainline.org

arm64: dts: qcom: msm8998-oneplus: Apply style fixes

Add some newlines, reorder some properties, remove some indentation to make
it more coherent.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220430162353.607709-8-konrad.dybcio@somainline.org

arm64: dts: qcom: msm8998-yoshino/oneplus: Use pm8005_regulators label

Now that a label is added, use it!

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220430162353.607709-7-konrad.dybcio@somainline.org

arm64: dts: qcom: msm8998-yoshino: Remove simple-bus compatible from clocks{}

It's not necessary and the SoC clocks{} node doesn't use it either.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220430162353.607709-6-konrad.dybcio@somainline.org

arm64: dts: qcom: msm8998-yoshino: Add USB extcon

While not strictly necessary, at least on maple, configure the USB extcon,
which requires two pins on Yoshino.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220430162353.607709-5-konrad.dybcio@somainline.org

arm64: dts: qcom: msm8998-yoshino-lilac: Disable LVS1

It's disabled on downstream, follow it.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220430162353.607709-4-konrad.dybcio@somainline.org

arm64: dts: qcom: msm8998-laptops: Clean up DTs

Reorder properties to match new laptop DTs, change hex to dec.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220430162353.607709-3-konrad.dybcio@somainline.org

arm64: dts: qcom: msm8998-clamshell: Clean up the DT

Keep the nodes and includes in order, clean up unnecessary properties & nodes.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220430162353.607709-2-konrad.dybcio@somainline.org

arm64: dts: qcom: msm8998*: Fix TLMM and pin nodes

Remove the unnecessary level of indentation, commonize SDC2 pins and notice
that SDCC2_CD_ON and _OFF is identical, deduplicate it!

Also, remove some unnecessary overrides and use decimal values in #-cells

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220430162353.607709-1-konrad.dybcio@somainline.org

arm64: dts: qcom: sdm845: Add camss vdda-pll-supply

Add in the missing vdda-pll-supply rail description.

Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220111125212.2343184-5-bryan.odonoghue@linaro.org

arm64: dts: qcom: sdm845: Rename camss vdda-supply to vdda-phy-supply

The dts entry vdda-supply connects to a common vdda-phy-supply rail. Rename
to reflect what the functionality is.

Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220111125212.2343184-4-bryan.odonoghue@linaro.org

arm64: dts: qcom: timer should use only 32-bit size

There's no reason the timer needs > 32-bits of address or size.
Since we using 32-bit size, we need to define ranges properly.

Fixes warnings as:
```
arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dt.yaml: timer@17c90000: #size-cells:0:0: 1 was expected
        From schema: Documentation/devicetree/bindings/timer/arm,arch_timer_mmio.yaml
```

Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220626105800.35586-1-david@ixit.cz

arm64: dts: qcom: align OPP table names with DT schema

DT schema expects names of operating points tables to start with
"opp-table":

  ipq6018-cp01-c1.dtb: cpu_opp_table: $nodename:0: 'cpu_opp_table' does not match '^opp-table(-[a-z0-9]+)?$'

Use hyphens instead of underscores, fix the names to match DT schema or
remove the prefix entirely when it is not needed.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220627093250.84391-1-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sm8250: Disable camcc by default

At the moment there are no changes in SM8250 board files, which require
camera clock controller to run, whenever it is needed for a particular
board, the status of camcc device node will be changed in a board file.

Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220518091943.734478-1-vladimir.zapolskiy@linaro.org

arm64: dts: qcom: msm8996: add clocks to the MMCC device node

As we are converting this platform to use DT clock bindings, add clocks
and clock-names properties to the MMCC device tree node.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220617122922.769562-7-dmitry.baryshkov@linaro.org

arm64: dts: qcom: sm8450: add uart20 node

Add device tree node for uart20, which is typically used for Bluetooth attachment.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220502195133.275209-1-dmitry.baryshkov@linaro.org

arm64: dts: qcom: sc7280-qcard: Add ldo_l17b regulator node

Add pm7325 ldo_l17b regulator, which is required for
wcd codec vdd buck supply on sc7280-qcard board.

Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1650621734-10297-1-git-send-email-quic_srivasam@quicinc.com

arm64: dts: qcom: sc7280: Set SPI flash to 50 MHz for herobrine boards

sc7280-herobrine based boards are specced to be able to access their
SPI flash at 50 MHz with the drive strength of the pins set at 8. The
drive strength is already set to 8 in "sc7280-herobrine.dtsi", so
let's bump up the clock. The matching firmware change for this is at:

https://review.coreboot.org/c/coreboot/+/63948

NOTE: the firmware change isn't _required_ to make the kernel work at
50 MHz, it merely shows that the boards are known to work fine at 50
MHz.

ALSO NOTE: this doesn't update the "sc7280-chrome-common.dtsi" file
which is used by both herobrine boards and IDP. At the moment the IDP
boards aren't configuring a drive strength of 8 and it seems safer to
just leave them at the slower speed if they're already working.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220505161425.1.Icf6f3796d2fa122b4c0566d9317b461bfbc24b7f@changeid

arm64: dts: qcom: sc7280: Set modem FW path for Chrome OS boards

Specify the path of the modem FW for SC7280 Chrome OS boards in
the 'remoteproc_mpss' node.

Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220510104656.1.Id98b473e08c950f9a461826dde187ef7705a928c@changeid

arm64: qcom: sc7280-herobrine: Enable DP

This enables DisplayPort for herobrine boards.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220513065704.1.I9b9b9d4d1a3e0350a89221892261881a1771ad15@changeid

arm64: dts: qcom: sc7180: Remove ipa_fw_mem node on trogdor

We don't use this carveout on trogdor boards, and having it defined in
the sc7180 SoC file causes an overlap message to be printed at boot.

 OF: reserved mem: OVERLAP DETECTED!
 memory@86000000 (0x0000000086000000--0x000000008ec00000) overlaps with memory@8b700000 (0x000000008b700000--0x000000008b710000)

Delete the node in the trogdor dtsi file to fix the overlap problem and
remove the error message.

Cc: Alex Elder <elder@linaro.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Fixes: 310b266655a3 ("arm64: dts: qcom: sc7180: define ipa_fw_mem node")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220517193307.3034602-1-swboyd@chromium.org

arm64: dts: qcom: sc7280: Enable wifi for Chrome OS boards

Enable the 'wifi' and 'remoteproc_wpss' nodes for all sc7280
based Chrome OS boards. Delete the corresponding entries from
sc7280-idp.dtsi since this file includes sc7280-chrome-common.dtsi.

Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220518155252.1.I176d4254c79cfaafa38cbe36f066f02f819df9b6@changeid

dt-bindings: arm: qcom: Add more sc7180 Chromebook board bindings

This adds board bindings for boards that are downstream but not quite
upstream yet.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220520143502.v4.5.Ie8713bc0377672ed8dd71189e66fc0b77226fb85@changeid

dt-bindings: arm: qcom: Add / fix sc7280 board bindings

This copy-pastes compatibles from sc7280-based boards from the device
trees to the yaml file. It also fixes the CRD/IDP bindings which had
gotten stale.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220520143502.v4.4.I1318c1ae2ce55ade1d092fc21df846360b15c560@changeid

dt-bindings: arm: qcom: Add sc7180 Chromebook board bindings

This copy-pastes compatibles from sc7180-based boards from the device
trees to the yaml file so that `make dtbs_check` will be happy.

NOTES:
- I make no attempt to try to share an "item" for all sc7180 based
  Chromebooks. Because of the revision matching scheme used by the
  Chromebook bootloader, at times we need a different number of
  revisions listed.
- Some of the odd entries in here (like google,homestar-rev23 or the
  fact that "Google Lazor Limozeen without Touchscreen" changed from
  sku5 to sku6) are not typos but simply reflect reality.
- Many revisions of boards here never actually went to consumers, but
  they are still in use within various companies that were involved in
  Chromebook development. Since Chromebooks are developed with an
  "upstream first" methodology, having these revisions supported with
  upstream Linux is important. Making it easy for Chromebooks to be
  developed with an "upstream first" methodology is valuable to the
  upstream community because it improves the quality of upstream and
  gets Chromebooks supported with vanilla upstream faster.

One other note here is that, though the bootloader effectively treats
the list of compatibles in a given device tree as unordered, some
people would prefer future boards to list higher-numbered revisions
first in the list. Chromebooks here are not changing and typically
list lower revisions first just to avoid churn.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220520143502.v4.3.I9804fcd5d6c8552ab25f598dd7a3ea71b15b55f0@changeid

dt-bindings: arm: qcom: Mention that Chromebooks use a different scheme

The qcom.yaml bindings file has a whole description of what the
top-level compatible should look like for Qualcomm devices. It doesn't
match what Chromebooks do, so add a link to the Chromebook docs.

Reported-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220520143502.v4.2.I6418884d8bab6956c7016304f45adc7df808face@changeid

dt-bindings: Document how Chromebooks with depthcharge boot

This documents how many Chromebooks pick the device tree that will be
passed to the OS and can help understand the revisions / SKUs listed
as the top-level "compatible" in many Chromebooks.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220520143502.v4.1.I71e42c6174f1cec17da3024c9f73ba373263b9b6@changeid

arm64: dts: qcom: sc7280: Enable keyboard backlight for villager

Villager has a backlit keyboard, enable support for the backlight.

Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220523123157.v2.2.I3d1b5a109675a0cc90e66a4e0b45cb823edbdee7@changeid

arm64: dts: qcom: sc7280: herobrine: Don't disable the keyboard backlight node

On herobrine boards the keyboard backlight is controlled through the
PWM LED driver. Currently both the PWM LED node and the node for the
keyboard backlight are disabled in sc7280-herobrine.dtsi, which
requires boards with a backlit keyboard to enable both nodes. There
are no other PWM LEDs on herobrine boards besides the keyboard
backlight, delete the 'disabled' status from the keyboard backlight
node, with that boards only have to enable the 'pwmleds' node for
keyboard backlight support.

Also add a label to the 'pwmleds' node to allow board files to refer to
it with a phandle.

Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220523123157.v2.1.I47ec78581907f7ef024f10bc085f970abf01ec11@changeid

arm64: dts: qcom: sc7280: Add touchscreen to villager

This adds the touchscreen to the sc7280-herobrine-villager device
tree. Note that the touchscreen on villager actually uses the reset
line and thus we use the more specific "elan,ekth6915" compatible
which allows us to specify the reset.

The fact that villager's touchscreen uses the reset line can be
contrasted against the touchscreen for CRD/herobrine-r1. On those
boards, even though the touchscreen goes to the display, it's not
hooked up to anything there.

In order to keep the line parked on herobrine/CRD, we'll move the
pullup from the qcard.dtsi file to the specific boards. This allows us
to disable the pullup in the villager device tree since the pin is an
output.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220524134840.1.I80072b8815ac08c12af8f379a33cc2d83693dc51@changeid

arm64: dts: qcom: sc7280-herobrine: Add lpi pinmux properties for CRD 3.0/3.1

Add LPASS LPI pinctrl properties, which are required for Audio
functionality on herobrine based platforms of rev5+
(aka CRD 3.0/3.1) boards.

Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1655108645-1517-5-git-send-email-quic_srivasam@quicinc.com

arm64: dts: qcom: sc7280: add lpass lpi pin controller node

Add LPASS LPI pinctrl node required for Audio functionality on sc7280
based platforms.

Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1655108645-1517-4-git-send-email-quic_srivasam@quicinc.com

arm64: dts: qcom: sc7280: Add secondary MI2S pinmux specifications for CRD 3.0/3.1

Add drive strength property for secondary MI2S on
sc7280 based platforms of rev5+ (aka CRD 3.0/3.1) boards.

Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1655108645-1517-3-git-send-email-quic_srivasam@quicinc.com

arm64: dts: qcom: sc7280: Add pinmux for I2S speaker and Headset

Add pinmux nodes for primary and secondary I2S for SC7280 based platforms.

Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1655108645-1517-2-git-send-email-quic_srivasam@quicinc.com

arm64: dts: qcom: sdm660-xiaomi-lavender: Configure WLED

WLED is used for controlling display backlight on this phone.

Signed-off-by: Dang Huynh <danct12@riseup.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220425032824.211975-1-danct12@riseup.net

arm64: dts: qcom: sm8250: remove assigned-clock-rate property for mdp clk

Drop the assigned clock rate property and vote on the mdp clock as per
calculated value during the usecase.

This patch is dependent on the patch ("drm/msm/disp/dpu1: set mdp clk
to the maximum frequency in opp table during probe") [1].

[1] https://lore.kernel.org/r/1647269217-14064-2-git-send-email-quic_vpolimer@quicinc.com/

Signed-off-by: Vinod Polimera <quic_vpolimer@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1647919631-14447-6-git-send-email-quic_vpolimer@quicinc.com

arm64: dts: qcom: sdm845: remove assigned-clock-rate property for mdp clk

Drop the assigned clock rate property and vote on the mdp clock as per
calculated value during the usecase.

This patch is dependent on the patch ("drm/msm/disp/dpu1: set mdp clk
to the maximum frequency in opp table during probe") [1].

[1] https://lore.kernel.org/r/1647269217-14064-2-git-send-email-quic_vpolimer@quicinc.com/

Signed-off-by: Vinod Polimera <quic_vpolimer@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1647919631-14447-5-git-send-email-quic_vpolimer@quicinc.com

arm64: dts: qcom: sm7180: remove assigned-clock-rate property for mdp clk

Drop the assigned clock rate property and vote on the mdp clock as per
calculated value during the usecase.

This patch is dependent on the patch ("drm/msm/disp/dpu1: set mdp clk
to the maximum frequency in opp table during probe") [1].

[1] https://lore.kernel.org/r/1647269217-14064-2-git-send-email-quic_vpolimer@quicinc.com/

Signed-off-by: Vinod Polimera <quic_vpolimer@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1647919631-14447-4-git-send-email-quic_vpolimer@quicinc.com

arm64: dts: qcom: sm7280: remove assigned-clock-rate property for mdp clk

Drop the assigned clock rate property and vote on the mdp clock as per
calculated value during the usecase.

This patch is dependent on the patch ("drm/msm/disp/dpu1: set mdp clk
to the maximum frequency in opp table during probe") [1].

[1] https://lore.kernel.org/r/1647269217-14064-2-git-send-email-quic_vpolimer@quicinc.com/

Signed-off-by: Vinod Polimera <quic_vpolimer@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1647919631-14447-3-git-send-email-quic_vpolimer@quicinc.com

Linux 5.19-rc1