Yuan Yao [Wed, 8 Jun 2016 10:24:56 +0000 (18:24 +0800)]
dts: ls2080aqds: Add QSPI dts node
Add QSPI controller and slave dts node for LS2080AQDS board.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Yuan Yao [Wed, 8 Jun 2016 10:24:55 +0000 (18:24 +0800)]
configs: ls2080aqds: Enable QSPI flash support
Enable QSPI flash related configure options.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Yuan Yao [Wed, 8 Jun 2016 10:24:54 +0000 (18:24 +0800)]
armv8: ls2080aqds: disable IFC NOR & QIXIS when QSPI enable
When QSPI is enabled, NOR flash and QIXIS can't be accessed
through IFC due to pin mux. Enable I2C QIXIS access and I2C
early init to read the sysclk and ddrclk.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Yuan Yao [Wed, 8 Jun 2016 10:24:53 +0000 (18:24 +0800)]
configs: ls2080a_common: Remove duplicate NOR configs
The NOR flash related configure options appear in ls2080aqds.h and
ls2080ardb.h, and the two files both includ ls2080a_common.h.
This patch remove the duplicated options in ls2080a_common.h.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Yuan Yao [Wed, 8 Jun 2016 10:24:52 +0000 (18:24 +0800)]
armv8: ls2080aqds: Select QSPI CLK div via SCFG
QSPI module output SCLK divisor value is configured through SCFG.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Yuan Yao [Wed, 8 Jun 2016 10:24:51 +0000 (18:24 +0800)]
drivers: i2c: mxc: Add early init
Add early i2c init function with conservative divider when the exact
clock rate is not available.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Pratiyush Mohan Srivastava [Wed, 20 Jan 2016 06:59:03 +0000 (12:29 +0530)]
board: ls2080a: Add "mcinitcmd" env for MC & DPL deployment
Environment variable mcinitcmd is defined to initiate MC and DPL
deployment from the location where it is stored (NOR, NAND, SD, SATA,
USB) during booting. If this variable is not defined then macro
MC_BOOT_ENV_VAR will be null and MC will not be booted and DPL will
not be applied during U-boot booting.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Yunhui Cui [Wed, 8 Jun 2016 02:31:42 +0000 (10:31 +0800)]
armv8/ls2080a: configure PMU's PCTBENR to enable WDT
The SP805-WDT module on LS2080A requires configuration of PMU's
PCTBENR register to enable watchdog counter decrement and reset
signal generation. The watchdog clock needs to be enabled first.
Signed-off-by: Yunhui Cui <yunhui.cui@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Heiko Schocher [Tue, 7 Jun 2016 06:55:45 +0000 (08:55 +0200)]
siemens,am33x: add draco etamin board
In the draco CPU board family, etamin is a new variant
with bigger flash and more RAM. Due to new flash that
uses larger pages (4K) some changes are necessary because
it impacts the MTD partition layout and the ubi mount
parameters.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
[trini: Move BOOTDELAY into defconfig, just always be 3 now]
Signed-off-by: Tom Rini <trini@konsulko.com>
Heiko Schocher [Tue, 7 Jun 2016 06:55:44 +0000 (08:55 +0200)]
dfu, nand, ubi: fix erasing after write finish
writting to ubi nand partitions need after write ends an erase
of the remaining sectors. This fail, if dfu write size was not
a multiple of erasesize, example log:
Failure erase: -1
Fix this error.
Signed-off-by: Heiko Schocher <hs@denx.de>
Heiko Schocher [Tue, 7 Jun 2016 06:55:43 +0000 (08:55 +0200)]
am335x, dxr2: get ECC sType from I2C eeprom
read the ECC Type field from the i2c eeprom, instead
configuring it static in the U-Boot binary.
see RM:
Table 26-17. NAND Geometry Information on I2C EEPROM
Signed-off-by: Heiko Schocher <hs@denx.de>
Heiko Schocher [Tue, 7 Jun 2016 06:55:42 +0000 (08:55 +0200)]
mtd: nand: omap: allow to switch to BCH16
support in omap_nand_switch_ecc() also an eccstrength
from 16.
Signed-off-by: Heiko Schocher <hs@denx.de>
Heiko Schocher [Tue, 7 Jun 2016 06:55:41 +0000 (08:55 +0200)]
nand: add nand mtd concat support
add for nand devices mtd concat support. Generic MTD concat
support is already ported to mainline, and used in the cfi_mtd
driver. This patch adds it similiar for nand devices.
Signed-off-by: Heiko Schocher <hs@denx.de>
Heiko Schocher [Tue, 7 Jun 2016 06:55:40 +0000 (08:55 +0200)]
ubi: add new ubi command "ubi detach"
simple detachs ubi from the mtd partition.
Signed-off-by: Heiko Schocher <hs@denx.de>
Samuel Egli [Tue, 7 Jun 2016 06:55:39 +0000 (08:55 +0200)]
siemens,am33x: add ubi fastmap support
From: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Heiko Schocher [Tue, 7 Jun 2016 06:31:25 +0000 (08:31 +0200)]
am335x, shc: add support for the am335x based bosch shc board
U-Boot SPL 2016.03-rc3-00019-g6dfb4c2-dirty (Mar 09 2016 - 07:40:06)
SHC C3-Sample
MPU reference clock runs at 6 MHz
Setting MPU clock to 594 MHz
Enabling Spread Spectrum of 18 permille for MPU
Trying to boot from MMC
reading u-boot.img
reading u-boot.img
U-Boot 2016.03-rc3-00019-g6dfb4c2-dirty (Mar 09 2016 - 07:05:35 +0100)
Watchdog enabled
I2C: ready
DRAM: 512 MiB
reloc off
1f783000
MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1
Net: cpsw
U-Boot#
Signed-off-by: Heiko Schocher <hs@denx.de>
Heiko Schocher [Tue, 7 Jun 2016 06:31:24 +0000 (08:31 +0200)]
doc, spl, am335x: update am335x-network
on the shc board we see when booting in net boot mode,
that the ROM bootloader sends "AM335x ROM" as
vendor-class-identifier. U-Boots doc says "DM814x ROM".
So, add the info to the doc, that there is also
"AM335x ROM" possible.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Heiko Schocher [Tue, 7 Jun 2016 06:31:23 +0000 (08:31 +0200)]
armv7: omap-common: make SPL board_mmc_init() weak
make this function weak, so board code can setup in SPL
MMC init with board special values.
Signed-off-by: Heiko Schocher <hs@denx.de>
Heiko Schocher [Tue, 7 Jun 2016 06:31:22 +0000 (08:31 +0200)]
mmc: omap_hsmmc: enable 8bit interface for eMMC for AM33xx
Enable 8bit interface on HSMMC2 for am33xx to support 8bit eMMC chips.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Heiko Schocher [Tue, 7 Jun 2016 06:31:21 +0000 (08:31 +0200)]
mmc: revert mmc: Handle switch error status bit in MMC card status
revert patch:
commit:
6b2221b008e0: mmc: Handle switch error status bit in MMC card status
to get eMMC working on shc board
Signed-off-by: Heiko Schocher <hs@denx.de>
Heiko Schocher [Tue, 7 Jun 2016 06:31:20 +0000 (08:31 +0200)]
bootstage: call show_boot_progress also in SPL
show_boot_progress() is now called from SPL also.
Signed-off-by: Heiko Schocher <hs@denx.de>
Heiko Schocher [Tue, 7 Jun 2016 06:31:19 +0000 (08:31 +0200)]
arm, am335x: Enable Spread Spectrum for the MPU
Enable Spread Spectrum for the MPU by calculating the required
values and setting the registers accordingly.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Heiko Schocher [Tue, 7 Jun 2016 06:31:18 +0000 (08:31 +0200)]
am335x: add some missing CM_CLKMODE_DPLL_SSC macros
add missing CM_CLKMODE_DPLL_SSC_ACK_MASK,
CM_CLKMODE_DPLL_SSC_DOWNSPREAD_MASK and
CM_CLKMODE_DPLL_SSC_TYPE_MASK
defines. Used for enabling spread spectrum.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Heiko Schocher [Tue, 7 Jun 2016 06:31:17 +0000 (08:31 +0200)]
arm, am335x: add some missing GPIO register definitions
add missing:
OMAP_GPIO_IRQSTATUS_SET_0 and OMAP_GPIO_IRQSTATUS_SET_1
registers.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Heiko Schocher [Tue, 7 Jun 2016 06:31:16 +0000 (08:31 +0200)]
power, tps65217: add some defines
add the following defines, needed for the upcoming shc board
support:
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Heiko Schocher [Tue, 7 Jun 2016 06:31:15 +0000 (08:31 +0200)]
tests: py: disable main_signon check for printenv cmd
if CONFIG_VERSION_VARIABLE is set, the U-Boot environment
contains a "vers" variable with the current U-Boot version
string. If now "printenv" is called, test/py fails as it
detects the main_sign string, which is in this case correct.
So check only the main_sign as an error, if CONFIG_VERSION_VARIABLE
is not set.
Signed-off-by: Heiko Schocher <hs@denx.de>
Heiko Schocher [Tue, 7 Jun 2016 06:31:14 +0000 (08:31 +0200)]
common: bootdelay: move CONFIG_BOOTDELAY into a Kconfig option
move CONFIG_BOOTDELAY into a Kconfig option. Used for this
purpose the moveconfig.py tool in tools.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Simon Glass [Thu, 9 Jun 2016 02:55:15 +0000 (20:55 -0600)]
tiny-printf: Correct the snprintf() implementation
This current code passes the variable arguments list to sprintf(). This is
not correct. Fix it by calling _vprintf() directly.
This makes firefly-rk3288 boot again.
Fixes: abeb272 ("tiny-printf: Support snprintf()")
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Wed, 8 Jun 2016 09:02:32 +0000 (18:02 +0900)]
ARM: uniphier: insert dsb barrier to ensure visibility of store
I noticed secondary CPUs sometimes fail to wake up, and the root
cause is that the sev instruction wakes up slave CPUs before the
preceding the register write is observed by them.
The read-back of the accessed register does not guarantee the order.
In order to ensure the order between the register write and the sev
instruction, a dsb instruction should be executed prior to the sev.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Tue, 7 Jun 2016 12:03:46 +0000 (21:03 +0900)]
ARM: uniphier: do not erase when updating U-Boot image in eMMC device
Unlike NAND, eMMC can be re-written without erasing.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Tue, 7 Jun 2016 12:03:44 +0000 (21:03 +0900)]
ARM: uniphier: do not overwrite fdt_file environment
This code auto-detects the best-match FDT file name, but it should
respect the user's choice if "fdt_file" environment is found in a
saved set of environments.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Tue, 7 Jun 2016 12:03:43 +0000 (21:03 +0900)]
ARM: uniphier: check return code of setenv()
Because setenv() may fail, it is better to check its return code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Sat, 4 Jun 2016 13:39:09 +0000 (22:39 +0900)]
ARM: uniphier: fix boot mode for PH1-LD11
This function is shared between PH1-LD11 and PH1-LD20. The difference
is the boot-mode latch for the USB boot mode.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Sat, 4 Jun 2016 13:39:08 +0000 (22:39 +0900)]
ARM: uniphier: support eMMC boot for PH1-LD11 and PH1-LD20
The Boot ROM on PH1-LD11/LD20 exports built-in APIs to load images
from an eMMC device. They are useful to reduce the memory footprint
of SPL, rather than compiling the whole MMC framework.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tom Rini [Mon, 6 Jun 2016 21:43:54 +0000 (17:43 -0400)]
Prepare v2016.07-rc1
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Mon, 6 Jun 2016 17:24:23 +0000 (13:24 -0400)]
Merge http://git.denx.de/u-boot-samsung
Signed-off-by: Tom Rini <trini@konsulko.com>
Conflicts:
configs/peach-pi_defconfig
configs/peach-pit_defconfig
B, Ravi [Fri, 3 Jun 2016 15:14:02 +0000 (20:44 +0530)]
ti_armv7_common: env: Fix hard coded mmc device for uuid
Avoid use of hard coded mmcdev value, use bootpart
instead, so finduuid works based on bootpart set
for a specific platform.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Andre Przywara [Tue, 31 May 2016 17:45:06 +0000 (10:45 -0700)]
arm/arm64: implement a boot header capability
Some SPL loaders (like Allwinner's boot0, and Broadcom's boot0)
require a header before the actual U-Boot binary to both check its
validity and to find other data to load. Sometimes this header may
only be a few bytes of information, and sometimes this might simply
be space that needs to be reserved for a post-processing tool.
Introduce a config option to allow assembler preprocessor commands
to be inserted into the code at the appropriate location; typical
assembler preprocessor commands might be:
.space 1000
.word 0x12345678
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
Commit Notes:
Please note that the current code:
start.S (arm64) and
vectors.S (arm)
already jumps over some portion of data already, so this option basically
just increases the size of this region (and the resulting binary).
For use with Allwinner's boot0 blob there is a tool called boot0img[1],
which fills the header to allow booting A64 based boards.
For the Pine64 we need a 1536 byte header (including the branch
instruction) at the moment, so we add this to the defconfig.
[1] https://github.com/apritzel/pine64/tree/master/tools
END
Reviewed-by: Tom Rini <trini@konsulko.com>
Chris Packham [Tue, 31 May 2016 08:30:59 +0000 (20:30 +1200)]
lib: make strmhz available in SPL
When setting up a DDR controller it is useful to be able to display
frequencies in a readable form. Make the strmhz() function available in
SPL builds provided there is full vsprintf available.
Reviewed-by: Tony O'Brien <tony.obrien@alliedtelesis.co.nz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Robert P. J. Day [Mon, 30 May 2016 10:55:53 +0000 (06:55 -0400)]
Remove unneeded remnants of bcopy().
Since bcopy() is no longer used, delete all remaining references to
it.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Lokesh Vutla [Mon, 6 Jun 2016 05:48:42 +0000 (11:18 +0530)]
configs: k2*_evm: Update fdt file names
Now that all Keystone2 dts file names are changed in Linux kernel, reflect the
same in evn variables inorder to find the right dtb file.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Mon, 6 Jun 2016 05:24:57 +0000 (10:54 +0530)]
ARM: DRA7xx: Enable FIT for hs platforms
Use a single defconfig for all DRA7xx hs platforms by enabling FIT and delete
the platform specific defconfigs.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Ladislav Michl [Thu, 2 Jun 2016 09:43:16 +0000 (11:43 +0200)]
armv7: fix order of OMAP die ID printing
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Alexander Graf [Sun, 5 Jun 2016 20:34:31 +0000 (22:34 +0200)]
efi_loader: Add DM_VIDEO support
Some systems are starting to shift to support DM_VIDEO which exposes
the frame buffer through a slightly different interface.
This is a poor man's effort to support the dm video interface instead
of the lcd one. We still only support a single display device.
Signed-off-by: Alexander Graf <agraf@suse.de>
[trini: Remove fb_size / fb_base as they were not used]
Signed-off-by: Tom Rini <trini@konsulko.com>
Alexander Graf [Fri, 27 May 2016 10:25:03 +0000 (12:25 +0200)]
efi_loader: Don't allocate from memory holes
When a payload calls our memory allocator with the exact address hint, we
happily allocate memory from completely unpopulated regions. Payloads however
expect this to only succeed if they would be allocating from free conventional
memory.
This patch makes the logic behind those checks a bit more obvious and ensures
that we always allocate from known good free conventional memory regions if we
want to allocate ram.
Reported-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Thu, 2 Jun 2016 09:38:27 +0000 (11:38 +0200)]
efi_loader: Move to normal debug infrastructure
We introduced special "DEBUG_EFI" defines when the efi loader
support was new. After giving it a bit of thought, turns out
we really didn't have to - the normal #define DEBUG infrastructure
works well enough for efi loader as well.
So this patch switches to the common debug() and #define DEBUG
way of printing debug information.
Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Fri, 20 May 2016 21:28:23 +0000 (23:28 +0200)]
efi_loader: Add exit support
Some times you may want to exit an EFI payload again, for example
to default boot into a PXE installation and decide that you would
rather want to boot from the local disk instead.
This patch adds exit functionality to the EFI implementation, allowing
EFI payloads to exit.
Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Fri, 20 May 2016 21:28:22 +0000 (23:28 +0200)]
arm: Introduce setjmp/longjmp
To quit an EFI application we will need logic to jump to the caller
of a function without returning from the function we called into,
so we need setjmp/longjmp functionality.
This patch introduces a trivial implementation of these that I
verified works on armv7, thumb2 and aarch64.
Signed-off-by: Alexander Graf <agraf@suse.de>
Dirk Eibach [Thu, 2 Jun 2016 07:05:42 +0000 (09:05 +0200)]
strider: Support cpu-dp flavor
There is new strider cpu flavor with DisplayPort video.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Tom Rini <trini@konsulko.com>
Dirk Eibach [Thu, 2 Jun 2016 07:05:41 +0000 (09:05 +0200)]
strider: Support con-dp flavor
There is a new strider console flavor with DisplayPort
video.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Tom Rini <trini@konsulko.com>
Dirk Eibach [Thu, 2 Jun 2016 07:05:40 +0000 (09:05 +0200)]
gdsys: osd: Allow osdsize on valid screens only
Limit "osdsize"-command to access valid screens only.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Tom Rini <trini@konsulko.com>
Dirk Eibach [Thu, 2 Jun 2016 07:05:39 +0000 (09:05 +0200)]
ioep-fpga: Support intempo compression
There is a new "intempo" compression type that can
be reported on startup.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Tom Rini <trini@konsulko.com>
Peter Howard [Thu, 2 Jun 2016 03:19:26 +0000 (13:19 +1000)]
Fix to davinci_nand.h to place CEnCFG registers at correct
Signed-off-by: Peter Howard <phoward@gme.net.au>
Ed Swarthout [Wed, 1 Jun 2016 13:11:24 +0000 (08:11 -0500)]
dm: scsi: if_typename should be scsi
Fixes:
=> ext2ls scsi 0:1
** Bad device scsi 0:1 **
for boards which use the scsi legacy driver (such as ls1043ardb).
Signed-off-by: Ed Swarthout <Ed.Swarthout@nxp.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tom Rini [Mon, 6 Jun 2016 14:04:58 +0000 (10:04 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-usb
Modified:
configs/ls1012afrdm_qspi_defconfig
configs/ls1012aqds_qspi_defconfig
configs/ls1012ardb_qspi_defconfig
include/configs/ls1012afrdm.h
include/configs/ls1012aqds.h
include/configs/ls1012ardb.h
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Mon, 6 Jun 2016 11:16:39 +0000 (07:16 -0400)]
Merge branch 'master' of git://denx.de/git/u-boot-microblaze
Michal Simek [Fri, 3 Jun 2016 09:35:17 +0000 (11:35 +0200)]
ARM64: zynqmp: Extend malloc space before relocation
For boards which have more devices it is necessary to extend malloc
space.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 22 Apr 2016 12:28:54 +0000 (14:28 +0200)]
ARM64: zynqmp: Add support for standard distro boot commands
Nand and QSPI are not defined now but this will be extended.
Based on selected bootmode boot_targets are rewritten.
Patch also contains detection if variables are saved. If yes don't
rewrite boot_targets variable.
Also move variable setup to the end of file because SCSI needs to be
defined before others macros are using it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Wed, 1 Jun 2016 20:41:54 +0000 (22:41 +0200)]
ARM64: zynqmp: Remove CONFIG_BOOTP_SERVERIP
When the CONFIG_BOOTP_SERVERIP option is set, we ignore all
dhcp values for the tftp server and use our own serverip and
file name instead.
This is usually not what we want and I doubt it's set for a
good reason on ZynqMP. It definitely hurts if we want to support
uEFI PXE boot on it. So just remove the option for now.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 1 Jun 2016 12:29:33 +0000 (14:29 +0200)]
ARM64: zynqmp: Enable AHCI when CONFIG_SATA_CEVA is defined
Simplify zcu102 board file by moving CONFIG_AHCI enabling to common
file.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 17 May 2016 06:38:53 +0000 (08:38 +0200)]
ARM64: zynqmp: Enable support for SPL FIT images
Enable support for RAM based FIT images read by SPL.
Empty function for now to keep compiler happy.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 30 May 2016 14:06:54 +0000 (16:06 +0200)]
env: Setup GD_FLG_ENV_DEFAULT flag when default environment are used
Setup flag when default environment are used to be able to
rewrite default distro boot variables based on SoC boot mode.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Michal Simek [Mon, 30 May 2016 12:57:02 +0000 (14:57 +0200)]
ARM64: zynq: Fix boot.bin generation for Zynq and ZynqMP
Fix boot.bin generation for Zynq and ZynqMP.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Marek Vasut <marex@denx.de>
Michal Simek [Mon, 30 May 2016 08:41:26 +0000 (10:41 +0200)]
ARM64: zynqmp: Extend page_table_size
0xc000 is not sufficient page table size if dc4 with 4 gems
is enabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 26 May 2016 06:06:38 +0000 (08:06 +0200)]
ARM64: zynqmp: Add support for zc1751-dc4
zc1751-dc4 contains four GEMs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 20 May 2016 07:55:00 +0000 (09:55 +0200)]
ARM64: zynqmp: Add debug uart for zc1751-dc2
Add debug uart for zc1751-dc2.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 30 May 2016 08:13:37 +0000 (10:13 +0200)]
ARM64: zynqmp: Enable Vitesse and RealTek ethernet phys
Phys are available on zc1751-dc4 that's why enable them.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 24 May 2016 09:45:11 +0000 (11:45 +0200)]
microblaze: Move MSR instruction selection to Kconfig
Select MSR instructions via Kconfig instead of xparameters.h.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 24 May 2016 11:23:59 +0000 (13:23 +0200)]
microblaze: Add option to pass cpu version number
Toolchain can use some flags by default based on cpu version.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 24 May 2016 09:42:26 +0000 (11:42 +0200)]
microblaze: Select compilation flags via Kconfig
Remove autogenerated config.mk and select CPU options via Kconfig.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 27 May 2016 09:25:49 +0000 (11:25 +0200)]
ARM64: zynqmp: Enable CMD_NAND via Kconfig
Simplify board file by enabling CMD_NAND via Kconfig.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Siva Durga Prasad Paladugu [Wed, 25 May 2016 09:50:38 +0000 (15:20 +0530)]
mtd: nand: arasan_nfc: Correct nand ecc initialization
Correct the nand ecc initialization code
This fixes the issue of incorrect nand ecc
init if no device is found in ecc_matrix then
it endsup ecc init with junk initialization
instead of the most suited one.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Marek Vasut [Sat, 4 Jun 2016 22:46:55 +0000 (00:46 +0200)]
arm: lib: Fix fix push/pop-section directives
Repair typos in the previous "arm: lib: fix push/pop-section directives"
patch, which prevented VCMA9 board from building.
Signed-off-by: Marek Vasut <marex@denx.de>
Fixes:
b2f1858455e9 ("arm: lib: fix push/pop-section directives")
Cc: Tom Warren <twarren@nvidia.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stephen Warren <swarren@nvidia.com>
Tom Rini [Sat, 4 Jun 2016 16:12:26 +0000 (12:12 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
Andreas Dannenberg [Fri, 3 Jun 2016 19:05:04 +0000 (14:05 -0500)]
spl: fit: Fix non-matching DT names console output
When no DTB can be matched successfully to the board that's being used
a list of available FIT-embedded DTBs will be output to the console for
diagnostic purposes. But rather than the contents of the "description"
FDT property a non-existent property was accessed and as a result "NULL"
was output instead of the actual name(s) of the DTB(s). Fix this issue
by using the correct property which is also the exact same property
that's used earlier during the actual board matching process.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Tom Rini [Sat, 4 Jun 2016 12:49:47 +0000 (08:49 -0400)]
Merge git://git.denx.de/u-boot-nand-flash
Tom Rini [Sat, 4 Jun 2016 12:49:08 +0000 (08:49 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq
Robert P. J. Day [Wed, 13 Apr 2016 21:49:28 +0000 (17:49 -0400)]
freescale: Tweak various Makefiles to remove redundancy, fix aesthetics
No intended functional change, just remove redundancies in some
Makefiles, and make whitespace aesthetics uniform.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-by: York Sun <york.sun@nxp.com>
mario.six@gdsys.cc [Wed, 25 May 2016 13:15:23 +0000 (15:15 +0200)]
dm: test: Add GPIO open drain tests
Add some tests for the new open drain setting feature of the GPIO
uclass, and extend the capabilities of the sandbox GPIO driver
accordingly.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
mario.six@gdsys.cc [Wed, 25 May 2016 13:15:22 +0000 (15:15 +0200)]
dm: gpio: Implement open drain for MPC85XX GPIO
This patch implements the open-drain setting feature for the MPC85XX
GPIO controller.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
mario.six@gdsys.cc [Wed, 25 May 2016 13:15:21 +0000 (15:15 +0200)]
dm: gpio: Add methods for open drain setting
Certain GPIO devices have the capability to switch their GPIOs into
open-drain mode, that is, instead of actively driving the output
(Push-pull output), the pin is connected to the collector (for a NPN
transistor) or the drain (for a MOSFET) of a transistor, respectively.
The pin then either forms an open circuit or a connection to ground,
depending on the state of the transistor.
This patch adds functions to the GPIO uclass to switch GPIOs to
open-drain mode on devices that support it.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
mario.six@gdsys.cc [Wed, 25 May 2016 13:15:20 +0000 (15:15 +0200)]
dm: gpio: Add driver for MPC85XX GPIO controller
This patch adds a driver for the built-in GPIO controller of the MPC85XX
SoC (probably supporting other PowerQUICC III SoCs as well).
Each GPIO bank is identified by its own entry in the device tree, i.e.
gpio-controller@fc00 {
#gpio-cells = <2>;
compatible = "fsl,pq3-gpio";
reg = <0xfc00 0x100>
}
By default, each bank is assumed to have 32 GPIOs, but the ngpios
setting is honored, so the number of GPIOs for each bank in configurable
to match the actual GPIO count of the SoC (e.g. the 32/32/23 banks of
the P1022 SoC).
The usual functions of GPIO drivers (setting input/output mode and output
value setting) are supported.
The driver has been tested on MPC85XX, but it is likely that other
PowerQUICC III devices will work as well.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Robert P. J. Day [Mon, 23 May 2016 10:49:21 +0000 (06:49 -0400)]
arch/powerpc: Simplify some calculations using ARRAY_SIZE() macro.
Replace a number of array length calculations with the ARRAY_SIZE()
macro, for clarity.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-by: York Sun <york.sun@nxp.com>
Shengzhou Liu [Tue, 31 May 2016 07:39:06 +0000 (15:39 +0800)]
board/freescale: Use unified setup_ddr_tlbs for spl boot and non-spl boot
We should use unified setup_ddr_tlbs() for spl boot and non-spl boot
to make sure 'M' bit is set for DDR TLB to maintain cache coherence.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Sumit Garg [Wed, 25 May 2016 16:41:48 +0000 (12:41 -0400)]
powerpc/board: SPL: Enable malloc flag in global data.
For malloc to work in SPL framework enable GD_FLG_FULL_MALLOC_INIT
flag in global data after allocating memory using mem_malloc_init.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Max Krummenacher [Mon, 30 May 2016 14:28:28 +0000 (16:28 +0200)]
nand: fix nand torture to use changed mtd api
The mtd subsystem deprecated and renamed the direct use of the mtd_info
struct's functionpointers. Instead the corresponding mtd_xxx function
should be used.
See also:
https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=
3c3c10bba1e4ccb75b41442e45c1a072f6cded19
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Scott Wood [Mon, 30 May 2016 18:57:58 +0000 (13:57 -0500)]
mtd: nand: Sync with Linux v4.6
Updates the NAND code to match Linux v4.6. The previous sync was from
Linux v4.1 in commit
d3963721d93fafa.
Note that none of the individual NAND drivers tracked Linux closely
enough to be synced themselves, other than manually applying a few
cross-tree changes.
Signed-off-by: Scott Wood <oss@buserror.net>
Tested-by: Heiko Schocher <hs@denx.de>
Scott Wood [Mon, 30 May 2016 18:57:57 +0000 (13:57 -0500)]
mtd: nand: Add page argument to write_page() etc.
This change is part of the Linux 4.6 sync. It is being done before the
main sync patch in order to make it easier to address the issue across
all NAND drivers (many/most of which do not closely track their Linux
counterparts) separately from other merge issues.
Signed-off-by: Scott Wood <oss@buserror.net>
Scott Wood [Mon, 30 May 2016 18:57:56 +0000 (13:57 -0500)]
mtd: nand: Add+use mtd_to/from_nand and nand_get/set_controller_data
These functions are part of the Linux 4.6 sync. They are being added
before the main sync patch in order to make it easier to address the
issue across all NAND drivers (many/most of which do not closely track
their Linux counterparts) separately from other merge issues.
Signed-off-by: Scott Wood <oss@buserror.net>
Scott Wood [Mon, 30 May 2016 18:57:55 +0000 (13:57 -0500)]
nand: Embed mtd_info in struct nand_chip
nand_info[] is now an array of pointers, with the actual mtd_info
instance embedded in struct nand_chip.
This is in preparation for syncing the NAND code with Linux 4.6,
which makes the same change to struct nand_chip. It's in a separate
commit due to the large amount of changes required to accommodate the
change to nand_info[].
Signed-off-by: Scott Wood <oss@buserror.net>
Scott Wood [Mon, 30 May 2016 18:57:54 +0000 (13:57 -0500)]
mtd: nand: Remove nand_info_t typedef
This typedef serves no purpose other than causing confusion with
struct nand_chip.
Signed-off-by: Scott Wood <oss@buserror.net>
Scott Wood [Mon, 30 May 2016 18:57:53 +0000 (13:57 -0500)]
mtd: nand: Remove docg4 driver and palmtreo680 flashing tool
Commit
ad4f54ea86b ("arm: Remove palmtreo680 board") removed the only
user of the docg4 driver and the palmtreo680 image flashing tool. This
patch removes them.
Signed-off-by: Scott Wood <oss@buserror.net>
Cc: Mike Dunn <mikedunn@newsguy.com>
Cc: Simon Glass <sjg@chromium.org>
Marek Vasut [Mon, 30 May 2016 18:57:52 +0000 (13:57 -0500)]
mtd: nand: Remove jz4740 driver
This driver is not used by anyone, remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Scott Wood <oss@buserror.net>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Scott Wood <oss@buserror.net>
Siva Durga Prasad Paladugu [Wed, 25 May 2016 09:50:38 +0000 (15:20 +0530)]
mtd: nand: arasan_nfc: Correct nand ecc initialization
Correct the nand ecc initialization code
This fixes the issue of incorrect nand ecc
init if no device is found in ecc_matrix then
it endsup ecc init with junk initialization
instead of the most suited one.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Masahiro Yamada [Fri, 3 Jun 2016 22:35:04 +0000 (07:35 +0900)]
usb: move CONFIG_USB_XHCI_DWC3 to Kconfig
Create an entry for "config USB_XHCI_DWC3" in Kconfig and
switch over to it for all boards.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Fri, 3 Jun 2016 22:35:03 +0000 (07:35 +0900)]
usb: move CONFIG_USB_XHCI to Kconfig with renaming
Move CONFIG_USB_XHCI to defconfig files for all boards, renaming it
into CONFIG_USB_XHCI_HCD.
As commented in the help of "config USB_XHCI" entry, this has been
a TODO for a long time; now CONFIG_USB_XHCI_HCD and CONFIG_USB_XHCI
have been unified in favor of the former.
Note:
Some boards define CONFIG_USB_XHCI in their headers without
CONFIG_USB, which does not meet the "depends on" in Kconfig.
I added CONFIG_USB=y for those boards when converting.
Otherwise, they would fail to build.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Fri, 3 Jun 2016 22:35:02 +0000 (07:35 +0900)]
configs: blackfin: move CONFIG_USB to defconfig
These Blackfin boards are the last ones that define CONFIG_USB in
their headers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Siva Durga Prasad Paladugu [Thu, 12 May 2016 06:57:13 +0000 (08:57 +0200)]
usb: dwc3: Correct datatype of base to unsigned long
Correct type of varibale base to unsigned long as
keeping it as int causes usb failures if MSB of
the base address is set.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Prabhakar Kushwaha [Fri, 3 Jun 2016 13:11:36 +0000 (18:41 +0530)]
armv8: ls1012a: Add support of ls1012afrdm board
QorIQ LS1012A FREEDOM (LS1012AFRDM) is a high-performance
development platform, with a complete debugging environment.
The LS1012AFRDM board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Prabhakar Kushwaha [Fri, 3 Jun 2016 13:11:35 +0000 (18:41 +0530)]
armv8: ls1012a: Add support of ls1012ardb board
QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
development platform, with a complete debugging environment.
The LS1012ARDB board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>