block: change all __u32 annotations to __be32 in affs_hardblocks.h

The Amiga partition parser module uses signed int for partition sector
address and count, which will overflow for disks larger than 1 TB.

Use u64 as type for sector address and size to allow using disks up to
2 TB without LBD support, and disks larger than 2 TB with LBD. The RBD
format allows to specify disk sizes up to 2^128 bytes (though native
OS limitations reduce this somewhat, to max 2^68 bytes), so check for
u64 overflow carefully to protect against overflowing sector_t.

This bug was reported originally in 2012, and the fix was created by
the RDB author, Joanne Dow <jdow@earthlink.net>. A patch had been
discussed and reviewed on linux-m68k at that time but never officially
submitted (now resubmitted as patch 1 of this series).

Patch 3 (this series) adds additional error checking and warning
messages. One of the error checks now makes use of the previously
unused rdb_CylBlocks field, which causes a 'sparse' warning
(cast to restricted __be32).

Annotate all 32 bit fields in affs_hardblocks.h as __be32, as the
on-disk format of RDB and partition blocks is always big endian.

Reported-by: Martin Steigerwald <Martin@lichtvoll.de>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=43511
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Message-ID: <201206192146.09327.Martin@lichtvoll.de>
Cc: <stable@vger.kernel.org> # 5.2
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20230620201725.7020-3-schmitzmic@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block: fix signed int overflow in Amiga partition support

The Amiga partition parser module uses signed int for partition sector
address and count, which will overflow for disks larger than 1 TB.

Use sector_t as type for sector address and size to allow using disks
up to 2 TB without LBD support, and disks larger than 2 TB with LBD.

This bug was reported originally in 2012, and the fix was created by
the RDB author, Joanne Dow <jdow@earthlink.net>. A patch had been
discussed and reviewed on linux-m68k at that time but never officially
submitted. This patch differs from Joanne's patch only in its use of
sector_t instead of unsigned int. No checking for overflows is done
(see patch 3 of this series for that).

Reported-by: Martin Steigerwald <Martin@lichtvoll.de>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=43511
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Message-ID: <201206192146.09327.Martin@lichtvoll.de>
Cc: <stable@vger.kernel.org> # 5.2
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Martin Steigerwald <Martin@lichtvoll.de>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230620201725.7020-2-schmitzmic@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block: add capacity validation in bdev_add_partition()

In the function bdev_add_partition(),there is no check that the start
and end sectors exceed the size of the disk before calling add_partition.
When we call the block's ioctl interface directly to add a partition,
and the capacity of the disk is set to 0 by driver,the command will
continue to execute.

Signed-off-by: Min Li <min15.li@samsung.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20230619091214.31615-1-min15.li@samsung.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block: fine-granular CAP_SYS_ADMIN for Persistent Reservation

Allow of unprivileged Persistent Reservation operations on devices
if the write permission check on the device node has passed.

brw-rw---- 1 root disk 259, 0 Jun 13 07:09 /dev/nvme0n1

In the example above, the "disk" group of nvme0n1 is also allowed to
make reservations on the device even without CAP_SYS_ADMIN.

Signed-off-by: Jingbo Xu <jefflexu@linux.alibaba.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230613084008.93795-3-jefflexu@linux.alibaba.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block: disallow Persistent Reservation on partitions

Refuse Persistent Reservation operations on partitions as reservation
on partitions doesn't make sense.

Besides, introduce blkdev_pr_allowed() helper, where more policies could
be placed here later.

Signed-off-by: Jingbo Xu <jefflexu@linux.alibaba.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230613084008.93795-2-jefflexu@linux.alibaba.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>

reiserfs: fix blkdev_put() warning from release_journal_dev()

In journal_init_dev(), if super bdev is used as 'j_dev_bd', then
blkdev_get_by_dev() is called with NULL holder, otherwise, holder will
be journal. However, later in release_journal_dev(), blkdev_put() is
called with journal unconditionally, cause following warning:

WARNING: CPU: 1 PID: 5034 at block/bdev.c:617 bd_end_claim block/bdev.c:617 [inline]
WARNING: CPU: 1 PID: 5034 at block/bdev.c:617 blkdev_put+0x562/0x8a0 block/bdev.c:901
RIP: 0010:blkdev_put+0x562/0x8a0 block/bdev.c:901
Call Trace:
 <TASK>
 release_journal_dev fs/reiserfs/journal.c:2592 [inline]
 free_journal_ram+0x421/0x5c0 fs/reiserfs/journal.c:1896
 do_journal_release fs/reiserfs/journal.c:1960 [inline]
 journal_release+0x276/0x630 fs/reiserfs/journal.c:1971
 reiserfs_put_super+0xe4/0x5c0 fs/reiserfs/super.c:616
 generic_shutdown_super+0x158/0x480 fs/super.c:499
 kill_block_super+0x64/0xb0 fs/super.c:1422
 deactivate_locked_super+0x98/0x160 fs/super.c:330
 deactivate_super+0xb1/0xd0 fs/super.c:361
 cleanup_mnt+0x2ae/0x3d0 fs/namespace.c:1247
 task_work_run+0x16f/0x270 kernel/task_work.c:179
 exit_task_work include/linux/task_work.h:38 [inline]
 do_exit+0xadc/0x2a30 kernel/exit.c:874
 do_group_exit+0xd4/0x2a0 kernel/exit.c:1024
 __do_sys_exit_group kernel/exit.c:1035 [inline]
 __se_sys_exit_group kernel/exit.c:1033 [inline]
 __x64_sys_exit_group+0x3e/0x50 kernel/exit.c:1033
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x39/0xb0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x63/0xcd

Fix this problem by passing in NULL holder in this case.

Reported-by: syzbot+04625c80899f4555de39@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=04625c80899f4555de39
Fixes: 2736e8eeb0cc ("block: use the holder as indication for exclusive opens")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230620111322.1014775-1-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block: fix wrong mode for blkdev_get_by_dev() from disk_scan_partitions()

After commit 2736e8eeb0cc ("block: use the holder as indication for
exclusive opens"), blkdev_get_by_dev() will warn if holder is NULL and
mode contains 'FMODE_EXCL'.

holder from blkdev_get_by_dev() from disk_scan_partitions() is always NULL,
hence it should not use 'FMODE_EXCL', which is broben by the commit. For
consequence, WARN_ON_ONCE() will be triggered from blkdev_get_by_dev()
if user scan partitions with device opened exclusively.

Fix this problem by removing 'FMODE_EXCL' from disk_scan_partitions(),
as it used to be.

Reported-by: syzbot+00cd27751f78817f167b@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=00cd27751f78817f167b
Fixes: 2736e8eeb0cc ("block: use the holder as indication for exclusive opens")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230618140402.7556-1-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block: document the holder argument to blkdev_get_by_path

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230620043536.707249-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block: increment diskseq on all media change events

Currently, associating a loop device with a different file descriptor
does not increment its diskseq.  This allows the following race
condition:

1. Program X opens a loop device
2. Program X gets the diskseq of the loop device.
3. Program X associates a file with the loop device.
4. Program X passes the loop device major, minor, and diskseq to
   something.
5. Program X exits.
6. Program Y detaches the file from the loop device.
7. Program Y attaches a different file to the loop device.
8. The opener finally gets around to opening the loop device and checks
   that the diskseq is what it expects it to be.  Even though the
   diskseq is the expected value, the result is that the opener is
   accessing the wrong file.

From discussions with Christoph Hellwig, it appears that
disk_force_media_change() was supposed to call inc_diskseq(), but in
fact it does not.  Adding a Fixes: tag to indicate this.  Christoph's
Reported-by is because he stated that disk_force_media_change()
calls inc_diskseq(), which is what led me to discover that it should but
does not.

Reported-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Demi Marie Obenour <demi@invisiblethingslab.com>
Fixes: e6138dc12de9 ("block: add a helper to raise a media changed event")
Cc: stable@vger.kernel.org # 5.15+
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230607170837.1559-1-demi@invisiblethingslab.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>

swim: fix a missing FMODE_ -> BLK_OPEN_ conversion in floppy_open

Fix a missing conversion to the new BLK_OPEN constant in swim.

Fixes: 05bdb9965305 ("block: replace fmode_t with a block-specific type for block open flags")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230620043051.707196-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>

blk-mq: fix NULL dereference on q->elevator in blk_mq_elv_switch_none

After grabbing q->sysfs_lock, q->elevator may become NULL because of
elevator switch.

Fix the NULL dereference on q->elevator by checking it with lock.

Reported-by: Guangwu Zhang <guazhang@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230616132354.415109-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>

iov_iter: remove iov_iter_get_pages and iov_iter_get_pages_alloc

Now that the direct I/O helpers have switched to use
iov_iter_extract_pages, these helpers are unused.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Reviewed-by: David Howells <dhowells@redhat.com>
Link: https://lore.kernel.org/r/20230614140341.521331-5-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block: remove BIO_PAGE_REFFED

Now that all block direct I/O helpers use page pinning, this flag is
unused.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: David Howells <dhowells@redhat.com>
Link: https://lore.kernel.org/r/20230614140341.521331-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>

splice: simplify a conditional in copy_splice_read

Check for -EFAULT instead of wrapping the check in an ret < 0 block.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Reviewed-by: David Howells <dhowells@redhat.com>
Link: https://lore.kernel.org/r/20230614140341.521331-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>

splice: don't call file_accessed in copy_splice_read

copy_splice_read calls into ->read_iter to read the data, which already
calls file_accessed.

Fixes: 33b3b041543e ("splice: Add a func to do a splice from an O_DIRECT file without ITER_PIPE")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Reviewed-by: David Howells <dhowells@redhat.com>
Link: https://lore.kernel.org/r/20230614140341.521331-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Merge tag 'nvme-6.5-2023-06-16' of git://git.infradead.org/nvme into for-6.5/block

Pull NVMe updates from Keith:

"nvme updates for Linux 6.5

 - Various cleanups all around (Irvin, Chaitanya, Christophe)
 - Better struct packing (Christophe JAILLET)
 - Reduce controller error logs for optional commands (Keith)
 - Support for >=64KiB block sizes (Daniel Gomez)
 - Fabrics fixes and code organization (Max, Chaitanya, Daniel Wagner)"

* tag 'nvme-6.5-2023-06-16' of git://git.infradead.org/nvme: (27 commits)
  nvme: forward port sysfs delete fix
  nvme: skip optional id ctrl csi if it failed
  nvme-core: use nvme_ns_head_multipath instead of ns->head->disk
  nvmet-fcloop: Do not wait on completion when unregister fails
  nvme-fabrics: open code __nvmf_host_find()
  nvme-fabrics: error out to unlock the mutex
  nvme: Increase block size variable size to 32-bit
  nvme-fcloop: no need to return from void function
  nvmet-auth: remove unnecessary break after goto
  nvmet-auth: remove some dead code
  nvme-core: remove redundant check from nvme_init_ns_head
  nvme: move sysfs code to a dedicated sysfs.c file
  nvme-fabrics: prevent overriding of existing host
  nvme-fabrics: check hostid using uuid_equal
  nvme-fabrics: unify common code in admin and io queue connect
  nvmet: reorder fields in 'struct nvmefc_fcp_req'
  nvmet: reorder fields in 'struct nvme_dhchap_queue_context'
  nvmet: reorder fields in 'struct nvmf_ctrl_options'
  nvme: reorder fields in 'struct nvme_ctrl'
  nvmet: reorder fields in 'struct nvmet_sq'
  ...

nvme: forward port sysfs delete fix

We had a late fix that modified nvme_sysfs_delete() after the staging
branch for the next merge window relocated the function to a new file.
Port commit 2eb94dd56a4a4 ("nvme: do not let the user delete a ctrl
before a complete") to the latest to avoid a potentially confusing merge
conflict.

Cc: Maurizio Lombardi <mlombard@redhat.com>
Cc: Max Gurtovoy <mgurtovoy@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>

bcache: fixup btree_cache_wait list damage

We get a kernel crash about "list_add corruption. next->prev should be
prev (ffff9c801bc01210), but was ffff9c77b688237c.
(next=ffffae586d8afe68)."

crash> struct list_head 0xffff9c801bc01210
struct list_head {
  next = 0xffffae586d8afe68,
  prev = 0xffffae586d8afe68
}
crash> struct list_head 0xffff9c77b688237c
struct list_head {
  next = 0x0,
  prev = 0x0
}
crash> struct list_head 0xffffae586d8afe68
struct list_head struct: invalid kernel virtual address: ffffae586d8afe68  type: "gdb_readmem_callback"
Cannot access memory at address 0xffffae586d8afe68

[230469.019492] Call Trace:
[230469.032041]  prepare_to_wait+0x8a/0xb0
[230469.044363]  ? bch_btree_keys_free+0x6c/0xc0 [escache]
[230469.056533]  mca_cannibalize_lock+0x72/0x90 [escache]
[230469.068788]  mca_alloc+0x2ae/0x450 [escache]
[230469.080790]  bch_btree_node_get+0x136/0x2d0 [escache]
[230469.092681]  bch_btree_check_thread+0x1e1/0x260 [escache]
[230469.104382]  ? finish_wait+0x80/0x80
[230469.115884]  ? bch_btree_check_recurse+0x1a0/0x1a0 [escache]
[230469.127259]  kthread+0x112/0x130
[230469.138448]  ? kthread_flush_work_fn+0x10/0x10
[230469.149477]  ret_from_fork+0x35/0x40

bch_btree_check_thread() and bch_dirty_init_thread() may call
mca_cannibalize() to cannibalize other cached btree nodes. Only one thread
can do it at a time, so the op of other threads will be added to the
btree_cache_wait list.

We must call finish_wait() to remove op from btree_cache_wait before free
it's memory address. Otherwise, the list will be damaged. Also should call
bch_cannibalize_unlock() to release the btree_cache_alloc_lock and wake_up
other waiters.

Fixes: 8e7102273f59 ("bcache: make bch_btree_check() to be multithreaded")
Fixes: b144e45fc576 ("bcache: make bch_sectors_dirty_init() to be multithreaded")
Cc: stable@vger.kernel.org
Signed-off-by: Mingzhe Zou <mingzhe.zou@easystack.cn>
Signed-off-by: Coly Li <colyli@suse.de>
Link: https://lore.kernel.org/r/20230615121223.22502-7-colyli@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>

bcache: Fix __bch_btree_node_alloc to make the failure behavior consistent

In some specific situations, the return value of __bch_btree_node_alloc
may be NULL. This may lead to a potential NULL pointer dereference in
caller function like a calling chain :
btree_split->bch_btree_node_alloc->__bch_btree_node_alloc.

Fix it by initializing the return value in __bch_btree_node_alloc.

Fixes: cafe56359144 ("bcache: A block layer cache")
Cc: stable@vger.kernel.org
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Signed-off-by: Coly Li <colyli@suse.de>
Link: https://lore.kernel.org/r/20230615121223.22502-6-colyli@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>

bcache: Remove unnecessary NULL point check in node allocations

Due to the previous fix of __bch_btree_node_alloc, the return value will
never be a NULL pointer. So IS_ERR is enough to handle the failure
situation. Fix it by replacing IS_ERR_OR_NULL check by an IS_ERR check.

Fixes: cafe56359144 ("bcache: A block layer cache")
Cc: stable@vger.kernel.org
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Signed-off-by: Coly Li <colyli@suse.de>
Link: https://lore.kernel.org/r/20230615121223.22502-5-colyli@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>

bcache: Remove dead references to cache_readaheads

The cache_readaheads stat counter is not used anymore and should be
removed.

Signed-off-by: Andrea Tomassetti <andrea.tomassetti-opensource@devo.com>
Signed-off-by: Coly Li <colyli@suse.de>
Link: https://lore.kernel.org/r/20230615121223.22502-4-colyli@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>

bcache: make kobj_type structures constant

Since commit ee6d3dd4ed48 ("driver core: make kobj_type constant.")
the driver core allows the usage of const struct kobj_type.

Take advantage of this to constify the structure definitions to prevent
modification at runtime.

Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Coly Li <colyli@suse.de>
Link: https://lore.kernel.org/r/20230615121223.22502-3-colyli@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>

bcache: Convert to use sysfs_emit()/sysfs_emit_at() APIs

Follow the advice of the Documentation/filesystems/sysfs.rst and show()
should only use sysfs_emit() or sysfs_emit_at() when formatting the
value to be returned to user space.

Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Signed-off-by: Coly Li <colyli@suse.de>
Link: https://lore.kernel.org/r/20230615121223.22502-2-colyli@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block: fix blktrace debugfs entries leakage

Commit 99d055b4fd4b ("block: remove per-disk debugfs files in
blk_unregister_queue") moves blk_trace_shutdown() from
blk_release_queue() to blk_unregister_queue(), this is safe if blktrace
is created through sysfs, however, there is a regression in corner
case.

blktrace can still be enabled after del_gendisk() through ioctl if
the disk is opened before del_gendisk(), and if blktrace is not shutdown
through ioctl before closing the disk, debugfs entries will be leaked.

Fix this problem by shutdown blktrace in disk_release(), this is safe
because blk_trace_remove() is reentrant.

Fixes: 99d055b4fd4b ("block: remove per-disk debugfs files in blk_unregister_queue")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230610022003.2557284-4-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>

scsi: sg: fix blktrace debugfs entries leakage

sg_ioctl() support to enable blktrace, which will create debugfs entries
"/sys/kernel/debug/block/sgx/", however, there is no guarantee that user
will remove these entries through ioctl, and deleting sg device doesn't
cleanup these blktrace entries.

This problem can be fixed by cleanup blktrace while releasing
request_queue, however, it's not a good idea to do this special handling
in common layer just for sg device.

Fix this problem by shutdown bltkrace in sg_device_destroy(), where the
device is deleted and all the users close the device, also grab a
scsi_device reference from sg_add_device() to prevent scsi_device to be
freed before sg_device_destroy();

Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20230610022003.2557284-3-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>

blktrace: use inline function for blk_trace_remove() while blktrace is disabled

If config is disabled, call blk_trace_remove() directly will trigger
build warning, hence use inline function instead, prepare to fix
blktrace debugfs entries leakage.

Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230610022003.2557284-2-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>

brd: use cond_resched instead of cond_resched_rcu

The body of the loop is run without RCU lock held. Use the regular
cond_resched() instead of cond_resched_rcu().

Fixes: 786bb0245881 ("brd: use XArray instead of radix-tree to index backing pages")
Suggested-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Pankaj Raghav <p.raghav@samsung.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20230614133538.1279369-1-p.raghav@samsung.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>

blk-mq: check on cpu id when there is only one ctx mapping

commit f168420c62e7 ("blk-mq: don't redirect completion for hctx withs
only one ctx mapping") When nvme applies a 1:1 mapping of hctx and ctx,
there will be no remote request.

But for ufs, the submission and completion queues could be asymmetric.
(e.g. Multiple SQs share one CQ) Therefore, 1:1 mapping of hctx and
ctx won't complete request on the submission cpu. In this situation,
this nr_ctx check could violate the QUEUE_FLAG_SAME_FORCE, as a result,
check on cpu id when there is only one ctx mapping.

Signed-off-by: Ed Tsai <ed.tsai@mediatek.com>
Signed-off-by: Po-Wen Kao <powen.kao@mediatek.com>
Suggested-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230614002529.6636-1-ed.tsai@mediatek.com
[axboe: fixed up indentation]
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Merge tag 'md-next-20230613' of https://git./linux/kernel/git/song/md into for-6.5/block

Pull MD updates from Song:

"The major changes are:

 1. Protect md_thread with rcu, by Yu Kuai;
 2. Various non-urgent raid5 and raid1/10 fixes, by Yu Kuai;
 3. Non-urgent raid10 fixes, by Li Nan."

* tag 'md-next-20230613' of https://git.kernel.org/pub/scm/linux/kernel/git/song/md: (29 commits)
  md/raid1-10: limit the number of plugged bio
  md/raid1-10: don't handle pluged bio by daemon thread
  md/md-bitmap: add a new helper to unplug bitmap asynchrously
  md/raid1-10: submit write io directly if bitmap is not enabled
  md/raid1-10: factor out a helper to submit normal write
  md/raid1-10: factor out a helper to add bio to plug
  md/raid10: prevent soft lockup while flush writes
  md/raid10: fix io loss while replacement replace rdev
  md/raid10: Do not add spare disk when recovery fails
  md/raid10: clean up md_add_new_disk()
  md/raid10: prioritize adding disk to 'removed' mirror
  md/raid10: improve code of mrdev in raid10_sync_request
  md/raid10: fix null-ptr-deref of mreplace in raid10_sync_request
  md/raid5: don't start reshape when recovery or replace is in progress
  md: protect md_thread with rcu
  md/bitmap: factor out a helper to set timeout
  md/bitmap: always wake up md_thread in timeout_store
  dm-raid: remove useless checking in raid_message()
  md: factor out a helper to wake up md_thread directly
  md: fix duplicate filename for rdev
  ...

block: Fix dio_cleanup() to advance the head index

Fix dio_bio_cleanup() to advance the head index into the list of pages past
the pages it has released, as __blockdev_direct_IO() will call it twice if
do_direct_IO() fails.

The issue was causing:

        WARNING: CPU: 6 PID: 2220 at mm/gup.c:76 try_get_folio

This can be triggered by setting up a clean pair of UDF filesystems on
loopback devices and running the generic/451 xfstest with them as the
scratch and test partitions.  Something like the following:

    fallocate /mnt2/udf_scratch -l 1G
    fallocate /mnt2/udf_test -l 1G
    mknod /dev/lo0 b 7 0
    mknod /dev/lo1 b 7 1
    losetup lo0 /mnt2/udf_scratch
    losetup lo1 /mnt2/udf_test
    mkfs -t udf /dev/lo0
    mkfs -t udf /dev/lo1
    cd xfstests
    ./check generic/451

with xfstests configured by putting the following into local.config:

    export FSTYP=udf
    export DISABLE_UDF_TEST=1
    export TEST_DEV=/dev/lo1
    export TEST_DIR=/xfstest.test
    export SCRATCH_DEV=/dev/lo0
    export SCRATCH_MNT=/xfstest.scratch

Fixes: 1ccf164ec866 ("block: Use iov_iter_extract_pages() and page pinning in direct-io.c")
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202306120931.a9606b88-oliver.sang@intel.com
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Christoph Hellwig <hch@infradead.org>
cc: David Hildenbrand <david@redhat.com>
cc: Andrew Morton <akpm@linux-foundation.org>
cc: Jens Axboe <axboe@kernel.dk>
cc: Al Viro <viro@zeniv.linux.org.uk>
cc: Matthew Wilcox <willy@infradead.org>
cc: Jan Kara <jack@suse.cz>
cc: Jeff Layton <jlayton@kernel.org>
cc: Jason Gunthorpe <jgg@nvidia.com>
cc: Logan Gunthorpe <logang@deltatee.com>
cc: Hillf Danton <hdanton@sina.com>
cc: Christian Brauner <brauner@kernel.org>
cc: Linus Torvalds <torvalds@linux-foundation.org>
cc: linux-fsdevel@vger.kernel.org
cc: linux-block@vger.kernel.org
cc: linux-kernel@vger.kernel.org
cc: linux-mm@kvack.org
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/1193485.1686693279@warthog.procyon.org.uk
Signed-off-by: Jens Axboe <axboe@kernel.dk>

md/raid1-10: limit the number of plugged bio

bio can be added to plug infinitely, and following writeback test can
trigger huge amount of plugged bio:

Test script:
modprobe brd rd_nr=4 rd_size=10485760
mdadm -CR /dev/md0 -l10 -n4 /dev/ram[0123] --assume-clean --bitmap=internal
echo 0 > /proc/sys/vm/dirty_background_ratio
fio -filename=/dev/md0 -ioengine=libaio -rw=write -bs=4k -numjobs=1 -iodepth=128 -name=test

Test result:
Monitor /sys/block/md0/inflight will found that inflight keep increasing
until fio finish writing, after running for about 2 minutes:

[root@fedora ~]# cat /sys/block/md0/inflight
       0  4474191

Fix the problem by limiting the number of plugged bio based on the number
of copies for original bio.

Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230529131106.2123367-8-yukuai1@huaweicloud.com

md/raid1-10: don't handle pluged bio by daemon thread

current->bio_list will be set under submit_bio() context, in this case
bitmap io will be added to the list and wait for current io submission to
finish, while current io submission must wait for bitmap io to be done.
commit 874807a83139 ("md/raid1{,0}: fix deadlock in bitmap_unplug.") fix
the deadlock by handling plugged bio by daemon thread.

On the one hand, the deadlock won't exist after commit a214b949d8e3
("blk-mq: only flush requests from the plug in blk_mq_submit_bio"). On
the other hand, current solution makes it impossible to flush plugged bio
in raid1/10_make_request(), because this will cause that all the writes
will goto daemon thread.

In order to limit the number of plugged bio, commit 874807a83139
("md/raid1{,0}: fix deadlock in bitmap_unplug.") is reverted, and the
deadlock is fixed by handling bitmap io asynchronously.

Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230529131106.2123367-7-yukuai1@huaweicloud.com

md/md-bitmap: add a new helper to unplug bitmap asynchrously

If bitmap is enabled, bitmap must update before submitting write io, this
is why unplug callback must move these io to 'conf->pending_io_list' if
'current->bio_list' is not empty, which will suffer performance
degradation.

A new helper md_bitmap_unplug_async() is introduced to submit bitmap io
in a kworker, so that submit bitmap io in raid10_unplug() doesn't require
that 'current->bio_list' is empty.

This patch prepare to limit the number of plugged bio.

Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230529131106.2123367-6-yukuai1@huaweicloud.com

md/raid1-10: submit write io directly if bitmap is not enabled

Commit 6cce3b23f6f8 ("[PATCH] md: write intent bitmap support for raid10")
add bitmap support, and it changed that write io is submitted through
daemon thread because bitmap need to be updated before write io. And
later, plug is used to fix performance regression because all the write io
will go to demon thread, which means io can't be issued concurrently.

However, if bitmap is not enabled, the write io should not go to daemon
thread in the first place, and plug is not needed as well.

Fixes: 6cce3b23f6f8 ("[PATCH] md: write intent bitmap support for raid10")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230529131106.2123367-5-yukuai1@huaweicloud.com

md/raid1-10: factor out a helper to submit normal write

There are multiple places to do the same thing, factor out a helper to
prevent redundant code, and the helper will be used in following patch
as well.

Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230529131106.2123367-4-yukuai1@huaweicloud.com

md/raid1-10: factor out a helper to add bio to plug

The code in raid1 and raid10 is identical, prepare to limit the number
of plugged bios.

Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230529131106.2123367-3-yukuai1@huaweicloud.com

md/raid10: prevent soft lockup while flush writes

Currently, there is no limit for raid1/raid10 plugged bio. While flushing
writes, raid1 has cond_resched() while raid10 doesn't, and too many
writes can cause soft lockup.

Follow up soft lockup can be triggered easily with writeback test for
raid10 with ramdisks:

watchdog: BUG: soft lockup - CPU#10 stuck for 27s! [md0_raid10:1293]
Call Trace:
 <TASK>
 call_rcu+0x16/0x20
 put_object+0x41/0x80
 __delete_object+0x50/0x90
 delete_object_full+0x2b/0x40
 kmemleak_free+0x46/0xa0
 slab_free_freelist_hook.constprop.0+0xed/0x1a0
 kmem_cache_free+0xfd/0x300
 mempool_free_slab+0x1f/0x30
 mempool_free+0x3a/0x100
 bio_free+0x59/0x80
 bio_put+0xcf/0x2c0
 free_r10bio+0xbf/0xf0
 raid_end_bio_io+0x78/0xb0
 one_write_done+0x8a/0xa0
 raid10_end_write_request+0x1b4/0x430
 bio_endio+0x175/0x320
 brd_submit_bio+0x3b9/0x9b7 [brd]
 __submit_bio+0x69/0xe0
 submit_bio_noacct_nocheck+0x1e6/0x5a0
 submit_bio_noacct+0x38c/0x7e0
 flush_pending_writes+0xf0/0x240
 raid10d+0xac/0x1ed0

Fix the problem by adding cond_resched() to raid10 like what raid1 did.

Note that unlimited plugged bio still need to be optimized, for example,
in the case of lots of dirty pages writeback, this will take lots of
memory and io will spend a long time in plug, hence io latency is bad.

Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230529131106.2123367-2-yukuai1@huaweicloud.com

md/raid10: fix io loss while replacement replace rdev

When removing a disk with replacement, the replacement will be used to
replace rdev. During this process, there is a brief window in which both
rdev and replacement are read as NULL in raid10_write_request(). This
will result in io not being submitted but it should be.

  //remove //write
  raid10_remove_disk raid10_write_request
   mirror->rdev = NULL
 read rdev -> NULL
   mirror->rdev = mirror->replacement
   mirror->replacement = NULL
 read replacement -> NULL

Fix it by reading replacement first and rdev later, meanwhile, use smp_mb()
to prevent memory reordering.

Fixes: 475b0321a4df ("md/raid10: writes should get directed to replacement as well as original.")
Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230602091839.743798-3-linan666@huaweicloud.com

md/raid10: Do not add spare disk when recovery fails

In raid10_sync_request(), if data cannot be read from any disk for
recovery, it will go to 'giveup' and let 'chunks_skipped' + 1. After
multiple 'giveup', when 'chunks_skipped >= geo.raid_disks', it will
return 'max_sector', indicating that the recovery has been completed.
However, the recovery is just aborted and the data remains inconsistent.

Fix it by setting mirror->recovery_disabled, which will prevent the spare
disk from being added to this mirror. The same issue also exists during
resync, it will be fixed afterwards.

Signed-off-by: Li Nan <linan122@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230602091839.743798-2-linan666@huaweicloud.com

md/raid10: clean up md_add_new_disk()

Commit 1a855a060665 ("md: fix bug with re-adding of partially recovered
device.") only add device which is set to In_sync. But it let devices
without metadata cannot be added when they should be.

Commit bf572541ab44 ("md: fix regression with re-adding devices to arrays
with no metadata") fix the above issue, it set device without metadata to
In_sync when add new disk.

However, after commit f466722ca614 ("md: Change handling of save_raid_disk
and metadata update during recovery.") deletes changes of the first patch,
setting In_sync for devcie without metadata is meanless because the flag
will be cleared soon and will not be used during this period. Clean it up.

Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230527101851.3266500-2-linan666@huaweicloud.com

md/raid10: prioritize adding disk to 'removed' mirror

When add a new disk to raid10, it will traverse conf->mirror from start
and find one of the following mirror to add:
  1. mirror->rdev is set to WantReplacement and it have no replacement,
     set new disk to mirror->replacement.
  2. no mirror->rdev, set new disk to mirror->rdev.

There is a array as below (sda is set to WantReplacement):

    Number   Major   Minor   RaidDevice State
       0       8        0        0      active sync set-A   /dev/sda
       -       0        0        1      removed
       2       8       32        2      active sync set-A   /dev/sdc
       3       8       48        3      active sync set-B   /dev/sdd

Use 'mdadm --add' to add a new disk to this array, the new disk will
become sda's replacement instead of add to removed position, which is
confusing for users. Meanwhile, after new disk recovery success, sda
will be set to Faulty.

Prioritize adding disk to 'removed' mirror is a better choice. In the
above scenario, the behavior is the same as before, except sda will not
be deleted. Before other disks are added, continued use sda is more
reliable.

Signed-off-by: Li Nan <linan122@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230527092007.3008856-1-linan666@huaweicloud.com

md/raid10: improve code of mrdev in raid10_sync_request

'need_recover' and 'mrdev' are equivalent in raid10_sync_request(), and
inc mrdev->nr_pending is unreasonable if don't need recovery. Replace
'need_recover' with 'mrdev', and only inc nr_pending when needed.

Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230527072218.2365857-3-linan666@huaweicloud.com

md/raid10: fix null-ptr-deref of mreplace in raid10_sync_request

There are two check of 'mreplace' in raid10_sync_request(). In the first
check, 'need_replace' will be set and 'mreplace' will be used later if
no-Faulty 'mreplace' exists, In the second check, 'mreplace' will be
set to NULL if it is Faulty, but 'need_replace' will not be changed
accordingly. null-ptr-deref occurs if Faulty is set between two check.

Fix it by merging two checks into one. And replace 'need_replace' with
'mreplace' because their values are always the same.

Fixes: ee37d7314a32 ("md/raid10: Fix raid10 replace hang when new added disk faulty")
Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230527072218.2365857-2-linan666@huaweicloud.com

md/raid5: don't start reshape when recovery or replace is in progress

When recovery is interrupted (reboot, etc.) check for MD_RECOVERY_RUNNING
is not enough to tell recovery is in progress. Also check recovery_cp
before starting reshape.

Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230529133410.2125914-1-yukuai1@huaweicloud.com

md: protect md_thread with rcu

Currently, there are many places that md_thread can be accessed without
protection, following are known scenarios that can cause
null-ptr-dereference or uaf:

1) sync_thread that is allocated and started from md_start_sync()
2) mddev->thread can be accessed directly from timeout_store() and
   md_bitmap_daemon_work()
3) md_unregister_thread() from action_store().

Currently, a global spinlock 'pers_lock' is borrowed to protect
'mddev->thread' in some places, this problem can be fixed likewise,
however, use a global lock for all the cases is not good.

Fix this problem by protecting all md_thread with rcu.

Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230523021017.3048783-6-yukuai1@huaweicloud.com

md/bitmap: factor out a helper to set timeout

Register/unregister 'mddev->thread' are both under 'reconfig_mutex',
however, some context didn't hold the mutex to access mddev->thread,
which can cause null-ptr-deference:

1) md_bitmap_daemon_work() can be called from md_check_recovery() where
'reconfig_mutex' is not held, deference 'mddev->thread' might cause
null-ptr-deference, because md_unregister_thread() reset the pointer
before stopping the thread.

2) timeout_store() access 'mddev->thread' multiple times,
null-ptr-deference can be triggered if 'mddev->thread' is reset in the
middle.

This patch factor out a helper to set timeout, the new helper always
check if 'mddev->thread' is null first, so that problem 1 can be fixed.

Now that this helper only access 'mddev->thread' once, but it's possible
that 'mddev->thread' can be freed while this helper is still in progress,
hence the problem is not fixed yet. Follow up patches will fix this by
protecting md_thread with rcu.

Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230523021017.3048783-5-yukuai1@huaweicloud.com

md/bitmap: always wake up md_thread in timeout_store

md_wakeup_thread() can handle the case that pass in md_thread is NULL,
the only difference is that md_wakeup_thread() will be called when
current timeout is 'MAX_SCHEDULE_TIMEOUT', this should not matter
because timeout_store() is not hot path, and the daemon process is
woke up more than demand from other context already.

Prepare to factor out a helper to set timeout.

Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230523021017.3048783-4-yukuai1@huaweicloud.com

dm-raid: remove useless checking in raid_message()

md_wakeup_thread() handle the case that pass in md_thread is NULL, there
is no need to check this.

Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230523021017.3048783-3-yukuai1@huaweicloud.com

md: factor out a helper to wake up md_thread directly

md_wakeup_thread() can't wakeup md_thread->tsk if md_thread->run is
still in progress, and in some cases md_thread->tsk need to be woke up
directly, like md_set_readonly() and do_md_stop().

Commit 9dfbdafda3b3 ("md: unlock mddev before reap sync_thread in
action_store") introduce a new scenario where unregister sync_thread is
not protected by 'reconfig_mutex', this can cause null-ptr-deference in
theroy:

t1: md_set_readonly t2: action_store
md_unregister_thread
// 'reconfig_mutex' is not held
// 'reconfig_mutex' is held by caller
if (mddev->sync_thread)
 thread = *threadp
 *threadp = NULL
 wake_up_process(mddev->sync_thread->tsk)
 // null-ptr-deference

Fix this problem by factoring out a helper to wake up md_thread directly,
so that 'sync_thread' won't be accessed multiple times from the reader
side. This helper also prepare to protect md_thread with rcu.

Noted that later patches is going to fix that unregister sync_thread is
not protected by 'reconfig_mutex' from action_store().

Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230523021017.3048783-2-yukuai1@huaweicloud.com

md: fix duplicate filename for rdev

Commit 5792a2856a63 ("[PATCH] md: avoid a deadlock when removing a device
from an md array via sysfs") delays the deletion of rdev, however, this
introduces a window that rdev can be added again while the deletion is
not done yet, and sysfs will complain about duplicate filename.

Follow up patches try to fix this problem by flushing workqueue, however,
flush_rdev_wq() is just dead code, the progress in
md_kick_rdev_from_array():

1) list_del_rcu(&rdev->same_set);
2) synchronize_rcu();
3) queue_work(md_rdev_misc_wq, &rdev->del_work);

So in flush_rdev_wq(), if rdev is found in the list, work_pending() can
never pass, in the meantime, if work is queued, then rdev can never be
found in the list.

flush_rdev_wq() can be replaced by flush_workqueue() directly, however,
this approach is not good:
- the workqueue is global, this synchronization for all raid disks is
  not necessary.
- flush_workqueue can't be called under 'reconfig_mutex', there is still
  a small window between flush_workqueue() and mddev_lock() that other
  contexts can queue new work, hence the problem is not solved completely.

sysfs already has apis to support delete itself through writer, and
these apis, specifically sysfs_break/unbreak_active_protection(), is used
to support deleting rdev synchronously. Therefore, the above commit can be
reverted, and sysfs duplicate filename can be avoided.

A new mdadm regression test is proposed as well([1]).

[1] https://lore.kernel.org/linux-raid/20230428062845.1975462-1-yukuai1@huaweicloud.com/

Fixes: 5792a2856a63 ("[PATCH] md: avoid a deadlock when removing a device from an md array via sysfs")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230523012727.3042247-1-yukuai1@huaweicloud.com

md/raid10: fix wrong setting of max_corr_read_errors

There is no input check when echo md/max_read_errors and overflow might
occur. Add check of input number.

Fixes: 1e50915fe0bb ("raid: improve MD/raid10 handling of correctable read errors.")
Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230522072535.1523740-3-linan666@huaweicloud.com

md/raid10: fix overflow of md/safe_mode_delay

There is no input check when echo md/safe_mode_delay in safe_delay_store().
And msec might also overflow when HZ < 1000 in safe_delay_show(), Fix it by
checking overflow in safe_delay_store() and use unsigned long conversion in
safe_delay_show().

Fixes: 72e02075a33f ("md: factor out parsing of fixed-point numbers")
Signed-off-by: Li Nan <linan122@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230522072535.1523740-2-linan666@huaweicloud.com

md/raid5: fix a deadlock in the case that reshape is interrupted

If reshape is in progress and io across reshape_position is issued, such
io will wait for reshape to make progress(see details in the case that
make_stripe_request() return STRIPE_SCHEDULE_AND_RETRY).

It has been reported several times that if system reboot while growing
raid5 to raid6, array assemble will hang infinitely([1, 2]). This is
because following deadlock is triggered:

1) a normal io is waiting for reshape to progress, this io can be from
   system-udevd or mdadm.
2) while assemble, mdadm tries to suspend the array, hence
   'reconfig_mutex' is held and mddev_suspend() must wait for normal io
   to be done.
3) daemon thread can't start reshape because 'reconfig_mutex' can't be
   held.

1) and 3) is unbreakable because they're foundation design. In order to
break 2), following is possible solutions that I can think of:

a) Let mddev_suspend() fail is not a good option, because this will
   break many scenarios since mddev_suspend() doesn't fail before.
b) Fail the io that is waiting for reshape to make progress from
   mddev_suspend().
c) Return false for the io that is waiting for reshape to make
   progress from raid5_make_request(), and these io will wait for
   suspend to be done in md_handle_request(), where 'active_io' is
   not grabbed.

c) sounds better than b), however, b) is used because it's easy and
straightforward, and it's verified that mdadm can assemble in this case.
On the other hand, c) breaks the logic that mddev_suspend() will wait
for submitted io to be completely handled.

Fix the problem by checking reshape in mddev_suspend(), if reshape can't
make progress and there are still some io waiting for reshape, fail
those io.

[1] https://lore.kernel.org/all/CAFig2csUV2QiomUhj_t3dPOgV300dbQ6XtM9ygKPdXJFSH__Nw@mail.gmail.com/
[2] https://lore.kernel.org/all/CAO2ABipzbw6QL5eNa44CQHjiVa-LTvS696Mh9QaTw+qsUKFUCw@mail.gmail.com/

Reported-by: Jove <jovetoo@gmail.com>
Reported-by: David Gilmour <dgilmour76@gmail.com>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230512015610.821290-6-yukuai1@huaweicloud.com

md: add a new api prepare_suspend() in md_personality

There are no functional changes, the new api will be used later to do
special handling for raid456 in md_suspend().

Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230512015610.821290-5-yukuai1@huaweicloud.com

md: export md_is_rdwr() and is_md_suspended()

The two apis will be used later to fix a deadlock in raid456, there are
no functional changes.

Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230512015610.821290-4-yukuai1@huaweicloud.com

md: fix data corruption for raid456 when reshape restart while grow up

Currently, if reshape is interrupted, echo "reshape" to sync_action will
restart reshape from scratch, for example:

echo frozen > sync_action
echo reshape > sync_action

This will corrupt data before reshape_position if the array is growing,
fix the problem by continue reshape from reshape_position.

Reported-by: Peter Neuwirth <reddunur@online.de>
Link: https://lore.kernel.org/linux-raid/e2f96772-bfbc-f43b-6da1-f520e5164536@online.de/
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230512015610.821290-3-yukuai1@huaweicloud.com

md/raid5: don't allow replacement while reshape is in progress

If reshape is interrupted(for example, echo frozen to sync_action), then
rdev replacement can be set. It's safe because reshape is always prior to
resync in md_check_recovery(). However, if system reboots, then kernel will
complain cannot handle concurrent replacement and reshape and this array
is not able to assemble anymore.

Fix this problem by don't allow replacement until reshape is done.

Reported-by: Peter Neuwirth <reddunur@online.de>
Link: https://lore.kernel.org/linux-raid/e2f96772-bfbc-f43b-6da1-f520e5164536@online.de/
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230512015610.821290-2-yukuai1@huaweicloud.com

md/raid10: check slab-out-of-bounds in md_bitmap_get_counter

If we write a large number to md/bitmap_set_bits, md_bitmap_checkpage()
will return -EINVAL because 'page >= bitmap->pages', but the return value
was not checked immediately in md_bitmap_get_counter() in order to set
*blocks value and slab-out-of-bounds occurs.

Move check of 'page >= bitmap->pages' to md_bitmap_get_counter() and
return directly if true.

Fixes: ef4256733506 ("md/bitmap: optimise scanning of empty bitmaps.")
Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230515134808.3936750-2-linan666@huaweicloud.com

raid6: neon: add missing prototypes

The raid6 syndrome functions are generated for different sizes and have
no generic prototype, while in the inner functions have a prototype
in a header that cannot be included from the correct file. In both
cases, the compiler warns about missing prototypes:

lib/raid6/recov_neon_inner.c:27:6: warning: no previous prototype for '__raid6_2data_recov_neon' [-Wmissing-prototypes]
lib/raid6/recov_neon_inner.c:77:6: warning: no previous prototype for '__raid6_datap_recov_neon' [-Wmissing-prototypes]
lib/raid6/neon1.c:56:6: warning: no previous prototype for 'raid6_neon1_gen_syndrome_real' [-Wmissing-prototypes]
lib/raid6/neon1.c:86:6: warning: no previous prototype for 'raid6_neon1_xor_syndrome_real' [-Wmissing-prototypes]
lib/raid6/neon2.c:56:6: warning: no previous prototype for 'raid6_neon2_gen_syndrome_real' [-Wmissing-prototypes]
lib/raid6/neon2.c:97:6: warning: no previous prototype for 'raid6_neon2_xor_syndrome_real' [-Wmissing-prototypes]
lib/raid6/neon4.c:56:6: warning: no previous prototype for 'raid6_neon4_gen_syndrome_real' [-Wmissing-prototypes]
lib/raid6/neon4.c:119:6: warning: no previous prototype for 'raid6_neon4_xor_syndrome_real' [-Wmissing-prototypes]
lib/raid6/neon8.c:56:6: warning: no previous prototype for 'raid6_neon8_gen_syndrome_real' [-Wmissing-prototypes]
lib/raid6/neon8.c:163:6: warning: no previous prototype for 'raid6_neon8_xor_syndrome_real' [-Wmissing-prototypes]

Add a new header file that contains the prototypes for both to avoid
the warnings.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230517132220.937200-1-arnd@kernel.org

swim3: fix the floppy_locked_ioctl prototype

Add back the accidentally dropped mode parameter.

Fixes: b60f7635788a ("swim3: fix the floppy_locked_ioctl prototype")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230613154309.327557-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvme: skip optional id ctrl csi if it failed

A frequently recieved report is the driver requests the optional Command
Set Specific Identify Controller structure. Some controllers report this
in their error log, which tiggers other warnings to user space
monitoring the devices.

These error entries are harmless and of questionable value to save in
the log, but let's reduce their occurance by not resending the command
if it previously failed. This will not prevent the errors on the initial
module load, but will greatly reduce their occurance on any rescans and
resumes from suspend.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=217445
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>

nvme-core: use nvme_ns_head_multipath instead of ns->head->disk

Change the way we check for a multipath nshead so as
to consistently use the same check to assert the same condition.

Signed-off-by: Irvin Cote <irvincoteg@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>

nvmet-fcloop: Do not wait on completion when unregister fails

The nvme_fc_unregister_localport() returns an error code in case that
the locaport pointer is NULL or has already been unegisterd. localport is
is either in the ONLINE state (all resources allocated) or has already
been put into DELETED state.

In this case we will never receive an wakeup call and thus any caller
will hang, e.g. module unload.

Signed-off-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>

nvme-fabrics: open code __nvmf_host_find()

There is no point in maintaining a separate funciton __nvmf_host_find()
that has only one caller nvmf_host_add() especially when caller and
callee both are small enough to merge.

Due to this we are actually repeating the error handling code in both
callee and caller for no reason that can be avoided, but instead we have
to read both function to establish the correctness along with additional
lockdep warning check due to involved locking.

Just open code __nvmf_host_find() in nvme_host_alloc() with appropriate
comment that removes repeated error checks in the callee/caller and
lockdep check that is needed for the nvmf_hosts_mutex involvement,
diffstats :-

 drivers/nvme/host/fabrics.c | 75 +++++++++++++------------------------
 1 file changed, 27 insertions(+), 48 deletions(-)

Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>

nvme-fabrics: error out to unlock the mutex

Currently, in the nvmf_host_add() function, if the nvmf_host_alloc()
call failed to allocate memory for the host, the code would directly
return -ENOMEM without unlocking the nvmf_hosts_mutex. This could
lead to potential issues with mutex synchronization.

Fix that error handling mechanism by jumping to the out_unlock label
when nvmf_host_alloc() fails. This ensures that the mutex is unlocked
before returning the error code. The updated code enhances avoids
possible deadlocks.

Fixes: f0cebf82004d ("nvme-fabrics: prevent overriding of existing host")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@inria.fr>
Closes: https://lore.kernel.org/r/202306020909.MTUEBeIa-lkp@intel.com/
Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Julia Lawall <julia.lawall@inria.fr>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>

nvme: Increase block size variable size to 32-bit

Increase block size variable size to 32-bit unsigned to be able to
support block devices larger than 32k (starting from 64 KiB).

Physical and logical block size already support unsigned 32-bit.

Signed-off-by: Daniel Gomez <da.gomez@samsung.com>
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>

nvme-fcloop: no need to return from void function

Remove return at the end of void function.

Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>

nvmet-auth: remove unnecessary break after goto

Remove dead break after goto.

Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>

nvmet-auth: remove some dead code

'status' is known to be 0 at the point.
And nvmet_auth_challenge() return a -E<ERROR_CODE> or 0.
So these lines of code should just be removed.

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>

nvme-core: remove redundant check from nvme_init_ns_head

nvme_find_ns_head already checks that the list of namescpaces
in an already existing namespace head is not empty

Signed-off-by: Irvin Cote <irvincoteg@gmail.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>

nvme: move sysfs code to a dedicated sysfs.c file

The core.c file became long and hard to maintain. Create a dedicated
file to centralize the sysfs functionality. This is a common practice to
separate sysfs/configfs related logic from the main driver logic .c file.
For example, in the nvmet module the configfs interface has its own
dedicated file.

This patch does not include any functional changes.

Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
[merged dhchap memleak fixes, include nvme-auth.h]
Signed-off-by: Keith Busch <kbusch@kernel.org>

nvme-fabrics: prevent overriding of existing host

When first connecting a target using the "default" host parameters,
setting the hostid from the command line during a subsequent connection
establishment would override the "default" hostid parameter. This would
cause an existing connection that is already using the host definitions
to lose its hostid.

To address this issue, the code has been modified to allow only 1:1
mapping between hostnqn and hostid. This will maintain unambiguous host
identification. Any non 1:1 mapping will be rejected during connection
establishment.

Tested-by: Noam Gottlieb <ngottlieb@nvidia.com>
Reviewed-by: Israel Rukshin <israelr@nvidia.com>
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>

nvme-fabrics: check hostid using uuid_equal

Use a dedicated function to match uuids instead of duplicating it.

Tested-by: Noam Gottlieb <ngottlieb@nvidia.com>
Reviewed-by: Israel Rukshin <israelr@nvidia.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>

nvme-fabrics: unify common code in admin and io queue connect

To simplify code maintenance, it is recommended to avoid duplicating
code.

Tested-by: Noam Gottlieb <ngottlieb@nvidia.com>
Reviewed-by: Israel Rukshin <israelr@nvidia.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>

nvmet: reorder fields in 'struct nvmefc_fcp_req'

Group some variables based on their sizes to reduce holes.
On x86_64, this shrinks the size of 'struct nvmefc_fcp_req' from
112 to 104 bytes.

This structure is embedded in some other structures (nvme_fc_fcp_op
which itself is embedded in nvme_fcp_op_w_sgl), so it helps reducing the
size of these structures too.

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>

nvmet: reorder fields in 'struct nvme_dhchap_queue_context'

Group some variables based on their sizes to reduce holes.
On x86_64, this shrinks the size of 'struct nvme_dhchap_queue_context' from
416 to 400 bytes.

This structure is kvcalloc()'ed in nvme_auth_init_ctrl(), so it is likely
that the allocation can be relatively big. Saving 16 bytes per structure
may might a slight difference.

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>

nvmet: reorder fields in 'struct nvmf_ctrl_options'

Group some variables based on their sizes to reduce holes.
On x86_64, this shrinks the size of 'struct nvmf_ctrl_options' from 136 to
128 bytes.

When such a structure is allocated in nvmf_create_ctrl(), because of the
way memory allocation works, when 136 bytes were requested, 192 bytes were
allocated.

So this saves 64 bytes per allocation, 1 cache line to hold the whole
structure and a few cycles when zeroing the memory in nvmf_create_ctrl().

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>

nvme: reorder fields in 'struct nvme_ctrl'

Group some variables based on their sizes to reduce holes.
On x86_64, this shrinks the size of 'struct nvme_ctrl' from 5368 to 5344
bytes when all CONFIG_* are defined.

This structure is embedded into some other structures, so it helps reducing
their size as well.

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>

nvmet: reorder fields in 'struct nvmet_sq'

Group some variables based on their sizes to reduce holes.
On x86_64, this shrinks the size of 'struct nvmet_sq' from 472 to 464
bytes when CONFIG_NVME_TARGET_AUTH is defined.

This structure is embedded into some other structures, so it helps reducing
their sizes as well.

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>

nvme-fabrics: add queue setup helpers

tcp and rdma transports have lots of duplicate code setting up the
different queue mappings. Add common helpers.

Cc: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>

nvme-pci: cleaning up nvme_pci_init_request

Erase the superfluous line that retrieves the nvme_dev.

Signed-off-by: Irvin Cote <irvincoteg@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>

nvme-rdma: fix typo in comment

There is no ib_stop_cq API and the need for the +1 is for ib_drain_qp.

Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Israel Rukshin <israelr@nvidia.com>
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>

nvme-core: fix dev_pm_qos memleak

Call dev_pm_qos_hide_latency_tolerance() in the error unwind patch to
avoid following kmemleak:-

blktests (master) # kmemleak-clear; ./check nvme/044;
blktests (master) # kmemleak-scan ; kmemleak-show
nvme/044 (Test bi-directional authentication)                [passed]
    runtime  2.111s  ...  2.124s
unreferenced object 0xffff888110c46240 (size 96):
  comm "nvme", pid 33461, jiffies 4345365353 (age 75.586s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<0000000069ac2cec>] kmalloc_trace+0x25/0x90
    [<000000006acc66d5>] dev_pm_qos_update_user_latency_tolerance+0x6f/0x100
    [<00000000cc376ea7>] nvme_init_ctrl+0x38e/0x410 [nvme_core]
    [<000000007df61b4b>] 0xffffffffc05e88b3
    [<00000000d152b985>] 0xffffffffc05744cb
    [<00000000f04a4041>] vfs_write+0xc5/0x3c0
    [<00000000f9491baf>] ksys_write+0x5f/0xe0
    [<000000001c46513d>] do_syscall_64+0x3b/0x90
    [<00000000ecf348fe>] entry_SYSCALL_64_after_hwframe+0x72/0xdc

Link: https://lore.kernel.org/linux-nvme/CAHj4cs-nDaKzMx2txO4dbE+Mz9ePwLtU0e3egz+StmzOUgWUrA@mail.gmail.com/
Fixes: f50fff73d620 ("nvme: implement In-Band authentication")
Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>

nvme-core: add missing fault-injection cleanup

Add missing fault-injection cleanup in nvme_init_ctrl() in the error
unwind path that also fixes following message for blktests:-

linux-block (for-next) # grep debugfs debugfs-err.log
[  147.853464] debugfs: Directory 'nvme1' with parent '/' already present!
[  147.853973] nvme1: failed to create debugfs attr
[  148.802490] debugfs: Directory 'nvme1' with parent '/' already present!
[  148.803244] nvme1: failed to create debugfs attr
[  148.877304] debugfs: Directory 'nvme1' with parent '/' already present!
[  148.877775] nvme1: failed to create debugfs attr
[  149.816652] debugfs: Directory 'nvme1' with parent '/' already present!
[  149.818011] nvme1: failed to create debugfs attr

Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>

nvme-core: fix memory leak in dhchap_ctrl_secret

Free dhchap_secret in nvme_ctrl_dhchap_ctrl_secret_store() before we
return when nvme_auth_generate_key() returns error.

Fixes: f50fff73d620 ("nvme: implement In-Band authentication")
Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>

nvme-core: fix memory leak in dhchap_secret_store

Free dhchap_secret in nvme_ctrl_dhchap_secret_store() before we return
fix following kmemleack:-

unreferenced object 0xffff8886376ea800 (size 64):
  comm "check", pid 22048, jiffies 4344316705 (age 92.199s)
  hex dump (first 32 bytes):
    44 48 48 43 2d 31 3a 30 30 3a 6e 78 72 35 4b 67  DHHC-1:00:nxr5Kg
    75 58 34 75 6f 41 78 73 4a 61 34 63 2f 68 75 4c  uX4uoAxsJa4c/huL
  backtrace:
    [<0000000030ce5d4b>] __kmalloc+0x4b/0x130
    [<000000009be1cdc1>] nvme_ctrl_dhchap_secret_store+0x8f/0x160 [nvme_core]
    [<00000000ac06c96a>] kernfs_fop_write_iter+0x12b/0x1c0
    [<00000000437e7ced>] vfs_write+0x2ba/0x3c0
    [<00000000f9491baf>] ksys_write+0x5f/0xe0
    [<000000001c46513d>] do_syscall_64+0x3b/0x90
    [<00000000ecf348fe>] entry_SYSCALL_64_after_hwframe+0x72/0xdc
unreferenced object 0xffff8886376eaf00 (size 64):
  comm "check", pid 22048, jiffies 4344316736 (age 92.168s)
  hex dump (first 32 bytes):
    44 48 48 43 2d 31 3a 30 30 3a 6e 78 72 35 4b 67  DHHC-1:00:nxr5Kg
    75 58 34 75 6f 41 78 73 4a 61 34 63 2f 68 75 4c  uX4uoAxsJa4c/huL
  backtrace:
    [<0000000030ce5d4b>] __kmalloc+0x4b/0x130
    [<000000009be1cdc1>] nvme_ctrl_dhchap_secret_store+0x8f/0x160 [nvme_core]
    [<00000000ac06c96a>] kernfs_fop_write_iter+0x12b/0x1c0
    [<00000000437e7ced>] vfs_write+0x2ba/0x3c0
    [<00000000f9491baf>] ksys_write+0x5f/0xe0
    [<000000001c46513d>] do_syscall_64+0x3b/0x90
    [<00000000ecf348fe>] entry_SYSCALL_64_after_hwframe+0x72/0xdc

Fixes: f50fff73d620 ("nvme: implement In-Band authentication")
Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>

blk-mq: fix potential io hang by wrong 'wake_batch'

In __blk_mq_tag_busy/idle(), updating 'active_queues' and calculating
'wake_batch' is not atomic:

t1: t2:
_blk_mq_tag_busy blk_mq_tag_busy
inc active_queues
// assume 1->2
inc active_queues
// 2 -> 3
blk_mq_update_wake_batch
// calculate based on 3
blk_mq_update_wake_batch
/* calculate based on 2, while active_queues is actually 3. */

Fix this problem by protecting them wih 'tags->lock', this is not a hot
path, so performance should not be concerned. And now that all writers
are inside the lock, switch 'actives_queues' from atomic to unsigned
int.

Fixes: 180dccb0dba4 ("blk-mq: fix tag_get wait task can't be awakened")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20230610023043.2559121-1-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>

fs: remove the now unused FMODE_* flags

FMODE_NDELAY, FMODE_EXCL and FMODE_WRITE_IOCTL were only used for
block internal purposed and are now entirely unused, so remove them.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Link: https://lore.kernel.org/r/20230608110258.189493-31-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block: store the holder in file->private_data

Store the file struct used as the holder in file->private_data as an
indicator that this file descriptor was opened exclusively to  remove
the last use of FMODE_EXCL.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20230608110258.189493-30-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block: always use I_BDEV on file->f_mapping->host to find the bdev

Always use I_BDEV(file->f_mapping->host) to find the bdev for a file to
free up file->private_data for other uses.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Christian Brauner <brauner@kernel.org>
Link: https://lore.kernel.org/r/20230608110258.189493-29-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block: replace fmode_t with a block-specific type for block open flags

The only overlap between the block open flags mapped into the fmode_t and
other uses of fmode_t are FMODE_READ and FMODE_WRITE.  Define a new
blk_mode_t instead for use in blkdev_get_by_{dev,path}, ->open and
->ioctl and stop abusing fmode_t.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jack Wang <jinpu.wang@ionos.com> [rnbd]
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Link: https://lore.kernel.org/r/20230608110258.189493-28-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block: remove unused fmode_t arguments from ioctl handlers

A few ioctl handlers have fmode_t arguments that are entirely unused,
remove them.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Christian Brauner <brauner@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20230608110258.189493-27-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block: move a few internal definitions out of blkdev.h

All these helpers are only used in core block code, so move them out of
the public header.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Christian Brauner <brauner@kernel.org>
Link: https://lore.kernel.org/r/20230608110258.189493-26-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>

ubd: remove commented out code in ubd_open

This code has been dead forever, make sure it doesn't show up in code
searches.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Christian Brauner <brauner@kernel.org>
Acked-by: Richard Weinberger <richard@nod.at>
Link: https://lore.kernel.org/r/20230608110258.189493-25-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>

rnbd-srv: replace sess->open_flags with a "bool readonly"

Stop passing the fmode_t around and just use a simple bool to track if
an export is read-only.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Christian Brauner <brauner@kernel.org>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Link: https://lore.kernel.org/r/20230608110258.189493-24-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>

mtd: block: use a simple bool to track open for write

Instead of propagating the fmode_t, just use a bool to track if a mtd
block device was opened for writing.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Christian Brauner <brauner@kernel.org>
Acked-by: Richard Weinberger <richard@nod.at>
Link: https://lore.kernel.org/r/20230608110258.189493-23-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>

nvme: replace the fmode_t argument to the nvme ioctl handlers with a simple bool

Instead of passing a fmode_t and only checking it fo0r FMODE_WRITE, pass
a bool open_for_write to prepare for callers that won't have the fmode_t.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Christian Brauner <brauner@kernel.org>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Link: https://lore.kernel.org/r/20230608110258.189493-22-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>

scsi: replace the fmode_t argument to ->sg_io_fn with a simple bool

Instead of passing a fmode_t and only checking it for FMODE_WRITE, pass
a bool open_for_write to prepare for callers that won't have the fmode_t.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Christian Brauner <brauner@kernel.org>
Link: https://lore.kernel.org/r/20230608110258.189493-21-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>

scsi: replace the fmode_t argument to scsi_ioctl with a simple bool

Instead of passing a fmode_t and only checking it for FMODE_WRITE, pass
a bool open_for_write to prepare for callers that won't have the fmode_t.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Christian Brauner <brauner@kernel.org>
Link: https://lore.kernel.org/r/20230608110258.189493-20-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>

scsi: replace the fmode_t argument to scsi_cmd_allowed with a simple bool

Instead of passing a fmode_t and only checking it for FMODE_WRITE, pass
a bool open_for_write to prepare for callers that won't have the fmode_t.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Christian Brauner <brauner@kernel.org>
Link: https://lore.kernel.org/r/20230608110258.189493-19-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>