review.tizen.org Git - platform/kernel/linux-exynos.git/log

Merge tag 'fixes-rcu-fiq-signed' of git://git./linux/kernel/git/tmlind/linux-omap into fixes

Fixes for omaps for v4.7-rc cycle:

- Two boot warning fixes from the RCU tree that should have gotten
  merged several weeks ago already but did not because of issues
  with who merges them. Paul has now split the RCU warning fixes into
  sets for various maintainers.

- Fix ams-delta FIQ regression caused by omap1 sparse IRQ changes

- Fix PM for omap3 boards using timer12 and gptimer, like the
  original beagleboard

- Fix hangs on am437x-sk-evm by lowering the I2C bus speed

* tag 'fixes-rcu-fiq-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: am437x-sk-evm: Reduce i2c0 bus speed for tps65218
  ARM: OMAP2+: timer: add probe for clocksources
  ARM: OMAP1: fix ams-delta FIQ handler to work with sparse IRQ
  arm: Use _rcuidle for smp_cross_call() tracepoints
  arm: Use _rcuidle tracepoint to allow use from idle

Signed-off-by: Olof Johansson <olof@lixom.net>

ARM: dts: STi: stih407-family: Disable reserved-memory co-processor nodes

This patch fixes a non-booting issue in Mainline.

When booting with a compressed kernel, we need to be careful how we
populate memory close to DDR start. AUTO_ZRELADDR is enabled by default
in multi-arch enabled configurations, which place some restrictions on
where the kernel is placed and where it will be uncompressed to on boot.

AUTO_ZRELADDR takes the decompressor code's start address and masks out
the bottom 28 bits to obtain an address to uncompress the kernel to
(thus a load address of 0x42000000 means that the kernel will be
uncompressed to 0x40000000 i.e. DDR START on this platform).

Even changing the load address to after the co-processor's shared memory
won't render a booting platform, since the AUTO_ZRELADDR algorithm still
ensures the kernel is uncompressed into memory shared with the first
co-processor (0x40000000).

Another option would be to move loading to 0x4A000000, since this will
mean the decompressor will decompress the kernel to 0x48000000. However,
this would mean a large chunk (0x44000000 => 0x48000000 (64MB)) of
memory would essentially be wasted for no good reason.

Until we can work with ST to find a suitable memory location to
relocate co-processor shared memory, let's disable the shared memory
nodes. This will ensure a working platform in the mean time.

NB: The more observant of you will notice that we're leaving the DMU
shared memory node enabled; this is because a) it is the only one in
active use at the time of this writing and b) it is not affected by
the current default behaviour which is causing issues.

Fixes: fe135c6 (ARM: dts: STiH407: Move over to using the 'reserved-memory' API for obtaining DMA memory)
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'imx-fixes-4.7' of git://git./linux/kernel/git/shawnguo/linux into fixes

The i.MX fixes for 4.7:
- Correct Micrel PHY mask to fix the issue that i.MX6UL ethernet works
in U-Boot but not in kernel.

* tag 'imx-fixes-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx6ul: Fix Micrel PHY mask

Signed-off-by: Olof Johansson <olof@lixom.net>

ARM: dts: am437x-sk-evm: Reduce i2c0 bus speed for tps65218

Based on the latest timing specifications for the TPS65218 from the data
sheet, http://www.ti.com/lit/ds/symlink/tps65218.pdf, document SLDS206
from November 2014, we must change the i2c bus speed to better fit within
the minimum high SCL time required for proper i2c transfer.

When running at 400khz, measurements show that SCL spends
0.8125 uS/1.666 uS high/low which violates the requirement for minimum
high period of SCL provided in datasheet Table 7.6 which is 1 uS.
Switching to 100khz gives us 5 uS/5 uS high/low which both fall above
the minimum given values for 100 khz, 4.0 uS/4.7 uS high/low.

Without this patch occasionally a voltage set operation from the kernel
will appear to have worked but the actual voltage reflected on the PMIC
will not have updated, causing problems especially with cpufreq that may
update to a higher OPP without actually raising the voltage on DCDC2,
leading to a hang.

Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Aparna Balasubramanian <aparnab@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

ARM: OMAP2+: timer: add probe for clocksources

A few platforms are currently missing clocksource_probe() completely
in their time_init functionality. On OMAP3430 for example, this is
causing cpuidle to be pretty much dead, as the counter32k is not
going to be registered and instead a gptimer is used as a clocksource.
This will tick in periodic mode, preventing any deeper idle states.

While here, also drop one unnecessary check for populated DT before
existing clocksource_probe() call.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

ARM: OMAP1: fix ams-delta FIQ handler to work with sparse IRQ

After OMAP1 IRQ definitions have been changed by commit 685e2d08c54b
("ARM: OMAP1: Change interrupt numbering for sparse IRQ") introduced
in v4.2, ams-delta FIQ handler which depends on them no longer works
as expected. Fix it.

Created and tested on Amstrad Delta against Linux-4.7-rc3

Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

arm: Use _rcuidle for smp_cross_call() tracepoints

Further testing with false negatives suppressed by commit 293e2421fe25
("rcu: Remove superfluous versions of rcu_read_lock_sched_held()")
identified another unprotected use of RCU from the idle loop. Because RCU
actively ignores idle-loop code (for energy-efficiency reasons, among
other things), using RCU from the idle loop can result in too-short
grace periods, in turn resulting in arbitrary misbehavior.

The resulting lockdep-RCU splat is as follows:

------------------------------------------------------------------------

===============================
[ INFO: suspicious RCU usage. ]
4.6.0-rc5-next-20160426+ #1112 Not tainted
-------------------------------
include/trace/events/ipi.h:35 suspicious rcu_dereference_check() usage!

other info that might help us debug this:

RCU used illegally from idle CPU!
rcu_scheduler_active = 1, debug_locks = 0
RCU used illegally from extended quiescent state!
no locks held by swapper/0/0.

stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.6.0-rc5-next-20160426+ #1112
Hardware name: Generic OMAP4 (Flattened Device Tree)
[<c0110308>] (unwind_backtrace) from [<c010c3a8>] (show_stack+0x10/0x14)
[<c010c3a8>] (show_stack) from [<c047fec8>] (dump_stack+0xb0/0xe4)
[<c047fec8>] (dump_stack) from [<c010dcfc>] (smp_cross_call+0xbc/0x188)
[<c010dcfc>] (smp_cross_call) from [<c01c9e28>] (generic_exec_single+0x9c/0x15c)
[<c01c9e28>] (generic_exec_single) from [<c01ca0a0>] (smp_call_function_single_async+0 x38/0x9c)
[<c01ca0a0>] (smp_call_function_single_async) from [<c0603728>] (cpuidle_coupled_poke_others+0x8c/0xa8)
[<c0603728>] (cpuidle_coupled_poke_others) from [<c0603c10>] (cpuidle_enter_state_coupled+0x26c/0x390)
[<c0603c10>] (cpuidle_enter_state_coupled) from [<c0183c74>] (cpu_startup_entry+0x198/0x3a0)
[<c0183c74>] (cpu_startup_entry) from [<c0b00c0c>] (start_kernel+0x354/0x3c8)
[<c0b00c0c>] (start_kernel) from [<8000807c>] (0x8000807c)

------------------------------------------------------------------------

Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: <linux-omap@vger.kernel.org>
Cc: <linux-arm-kernel@lists.infradead.org>

Merge tag 'samsung-fixes-4.7-2' of git://git./linux/kernel/git/krzk/linux into fixes

Fixes for Exynos-based Snow and Peach Pit boards for regressions introduced in
4.7-rc1 because OF graph logic expects specific names of child nodes.

* tag 'samsung-fixes-4.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Fix port nodes names for Exynos5420 Peach Pit board
ARM: dts: exynos: Fix port nodes names for Exynos5250 Snow board

Signed-off-by: Olof Johansson <olof@lixom.net>

MAINTAINERS: Add myself as reviewer of ARM FSL/NXP

I would like to help reviewing FSL/NXP ARM architecture patches.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'socfpga_fix_for_v4.7' of git://git./linux/kernel/git/dinguyen/linux into fixes

SoCFPGA fix for v4.7
- Add missing PHY phandle for SoCFPGA VINING board

* tag 'socfpga_fix_for_v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: socfpga: Add missing PHY phandle

Signed-off-by: Olof Johansson <olof@lixom.net>

ARM: imx6ul: Fix Micrel PHY mask

The value used for Micrel PHY mask is not correct. Use the
MICREL_PHY_ID_MASK definition instead.

Thanks to Jiri Luznicky for proposing the fix at
https://community.freescale.com/thread/387739

Cc: <stable@vger.kernel.org>
Fixes: 709bc0657fe6f9f55 ("ARM: imx6ul: add fec MAC refrence clock and phy fixup init")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: socfpga: Add missing PHY phandle

Add missing PHY phandle into the DT, otherwise the stmmac code won't
detect the PHY correctly anymore.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>

ARM: dts: exynos: Fix port nodes names for Exynos5420 Peach Pit board

Commit bea7eef6949c ("ARM: dts: exynos: Fix DTC unit name warnings in
Peach Pit") fixed the DTC warnings about mismatches between unit names
and reg properties in the Exynos5420 Peach Pit DTS.

But unfortunately it also added a regression on the Peach Pit when
changing the port node names since the OF graph logic expects the port
nodes to be always named 'port'.

The Documentation/devicetree/bindings/graph.txt binding document says
that when there is more than one port, '#address-cells', '#size-cells'
and 'reg' properties should be used to number the port nodes.

Fixes: bea7eef6949c ("ARM: dts: exynos: Fix DTC unit name warnings in Peach Pit")
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>

ARM: dts: exynos: Fix port nodes names for Exynos5250 Snow board

Commit 5c9cbade0629 ("ARM: dts: exynos: Fix DTC unit name warnings in
Exynos5250") fixed all the DTC warnings about mismatchs between unit
names and reg properties in Exynos5250 boards DTS.

But unfortunately it also added a regression on the Exynos5250 Snow
Chromebook when changing the port node names since the OF graph logic
expects the port nodes to be always named 'port'.

The Documentation/devicetree/bindings/graph.txt binding document says
that when there is more than one port, '#address-cells', '#size-cells'
and 'reg' properties should be used to number the port nodes.

Fixes: 5c9cbade0629 ("ARM: dts: exynos: Fix DTC unit name warnings in Exynos5250")
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>

ARM: dts: sun6i: yones-toptech-bs1078-v2: Drop constraints on dc1sw regulator

This is the same issue fixed in commit dcf5341f0150 ("ARM: dts:
sun8i-q8-common: Do not set constraints on dc1sw regulator").
Commit message copied:

dc1sw is an on/off only regulator and as such it cannot have constraints.

This is a limitation of the kernel regulator implementation which resolves
supplies on the first regulator_get(), which is done after applying
constraints, and applying the constrains will fail because it calls
_regulator_get_voltage() and _regulator_do_set_voltage() both of which
will fail on a switch regulator when there is no supply (yet).

This causes registering of all axp22x regulators to fail with the
following errors:

[    1.395249] vcc-lcd: failed to get the current voltage(-22)
[    1.405131] axp20x-regulator axp20x-regulator: Failed to register dc1sw
[    1.412436] axp20x-regulator: probe of axp20x-regulator failed with error -22

This commit removes the constrains on dc1sw / vcc-lcd fixing this problem.
Note that dcdc1 itself is contrained to the exact same values, so this
does not change anything.

Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Cc: <stable@vger.kernel.org> # 4.6
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

ARM: dts: sun6i: primo81: Drop constraints on dc1sw regulator

This is the same issue fixed in commit dcf5341f0150 ("ARM: dts:
sun8i-q8-common: Do not set constraints on dc1sw regulator").
Commit message copied:

dc1sw is an on/off only regulator and as such it cannot have constraints.

This is a limitation of the kernel regulator implementation which resolves
supplies on the first regulator_get(), which is done after applying
constraints, and applying the constrains will fail because it calls
_regulator_get_voltage() and _regulator_do_set_voltage() both of which
will fail on a switch regulator when there is no supply (yet).

This causes registering of all axp22x regulators to fail with the
following errors:

[    1.395249] vcc-lcd: failed to get the current voltage(-22)
[    1.405131] axp20x-regulator axp20x-regulator: Failed to register dc1sw
[    1.412436] axp20x-regulator: probe of axp20x-regulator failed with error -22

This commit removes the constrains on dc1sw / vcc-lcd fixing this problem.
Note that dcdc1 itself is contrained to the exact same values, so this
does not change anything.

Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Cc: <stable@vger.kernel.org> # 4.6
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v4.7-dts-fixes1' of git://git./linux/kernel/git/tmlind/linux-omap into fixes

DTS fixes for omaps for v4.7 merge window for issues noted
with patches in Linux next:

- Fix omap5 and am57xx-idk input voltages to fix micro-sd
  probing at least for some omap5-uevm configurations

- Fix unhandled fault for igepv5 audio

- Fix UART wakeirqs for omap5 by removing WAKUP_EN flags,
  those are managed by the wakeirq and can currently confuse
  the wakeirqs as there is no handler necessarily registered

- Fix LDO7 source for igepv5

Also included are few minor changes not strictly fixes
are good to have merged:

- Fix HP T410 boot time warnings for eMMC and disable the
  unused MMC interfaces while at it

- Add dra7 gpmc dma channel

- Add igep00x0 SD card detect and write protect GPIOs

* tag 'omap-for-v4.7-dts-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: igep0020: Add SD card write-protect pin.
  ARM: dts: igep00x0: Add SD card-detect.
  ARM: dts: am57xx-idk-common: Fix input supply names
  ARM: dts: dra7: Add gpmc dma channel
  ARM: dts: disable mmc by default and enable when needed for dm814x
  ARM: dts: Add non-removable to hsmmc on hp-t410
  ARM: dts: Fix ldo7 source for HDMI on igepv5
  ARM: dts: Fix uart wakeirq on omap5 by removing WAKEUP_EN for omaps
  ARM: dts: Fix igepv5 audiopwon-gpio
  ARM: dts: omap5-board-common: Describe the voltage supply mapping accurately

Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v4.7/fixes-v2' of git://git./linux/kernel/git/tmlind/linux-omap into fixes

Two fixes for omaps for v4.7 merge window, one to enable
ARM errata for am437x, and the other to add ARM errtum
workaround for dra7.

AFAIK these both can wait for v4.7, we can then request them
for stable kernels as needed.

* tag 'omap-for-v4.7/fixes-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: AM43XX: Enable fixes for Cortex-A9 errata
ARM: OMAP5 / DRA7: Introduce workaround for 801819

Signed-off-by: Olof Johansson <olof@lixom.net>

ARM: dts: sunxi: Add OLinuXino Lime2 eMMC to the Makefile

commit 27dd9af6bc000ab21fd ("ARM: dts: sunxi: Add a olinuxino-lime2-emmc")
added the new emmc equipped lime2 but forgot its Makefile.

This patch adds an entry to the Makefile.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'samsung-fixes-4.7' of git://git./linux/kernel/git/krzk/linux into fixes

Two fixes for v4.7 cycle for build issues:
1. Fix samsung-keypad build error if INPUT is selected as module.
   The error though depends on some uncommon build settings so it
   is not as easy to trigger.

2. Get rid of 'samsung_device_dma_mask' defined but not used warning.

* tag 'samsung-fixes-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
  ARM: exynos: don't select keyboard driver
  ARM: samsung: improve static dma_mask definition

Signed-off-by: Olof Johansson <olof@lixom.net>

arm64: dts: drop "arm,amba-bus" in favor of "simple-bus" part 2

Tree-wide replacement was done by commit 2ef7d5f342c1 (ARM, ARM64:
dts: drop "arm,amba-bus" in favor of "simple-bus"), but we have some
new users of "arm,amba-bus" at Linux 4.7-rc1. Eliminate them now.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Chanho Min <chanho.min@lge.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Linux 4.7-rc1

hash_string: Fix zero-length case for !DCACHE_WORD_ACCESS

The self-test was updated to cover zero-length strings; the function
needs to be updated, too.

Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: George Spelvin <linux@sciencehorizons.net>
Fixes: fcfd2fbf22d2 ("fs/namei.c: Add hashlen_string() function")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Rename other copy of hash_string to hashlen_string

The original name was simply hash_string(), but that conflicted with a
function with that name in drivers/base/power/trace.c, and I decided
that calling it "hashlen_" was better anyway.

But you have to do it in two places.

[ This caused build errors for architectures that don't define
CONFIG_DCACHE_WORD_ACCESS - Linus ]

Signed-off-by: George Spelvin <linux@sciencehorizons.net>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Fixes: fcfd2fbf22d2 ("fs/namei.c: Add hashlen_string() function")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

hpfs: implement the show_options method

The HPFS filesystem used generic_show_options to produce string that is
displayed in /proc/mounts. However, there is a problem that the options
may disappear after remount. If we mount the filesystem with option1
and then remount it with option2, /proc/mounts should show both option1
and option2, however it only shows option2 because the whole option
string is replaced with replace_mount_options in hpfs_remount_fs.

To fix this bug, implement the hpfs_show_options function that prints
options that are currently selected.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

affs: fix remount failure when there are no options changed

Commit c8f33d0bec99 ("affs: kstrdup() memory handling") checks if the
kstrdup function returns NULL due to out-of-memory condition.

However, if we are remounting a filesystem with no change to
filesystem-specific options, the parameter data is NULL.  In this case,
kstrdup returns NULL (because it was passed NULL parameter), although no
out of memory condition exists.  The mount syscall then fails with
ENOMEM.

This patch fixes the bug.  We fail with ENOMEM only if data is non-NULL.

The patch also changes the call to replace_mount_options - if we didn't
pass any filesystem-specific options, we don't call
replace_mount_options (thus we don't erase existing reported options).

Fixes: c8f33d0bec99 ("affs: kstrdup() memory handling")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

hpfs: fix remount failure when there are no options changed

Commit ce657611baf9 ("hpfs: kstrdup() out of memory handling") checks if
the kstrdup function returns NULL due to out-of-memory condition.

However, if we are remounting a filesystem with no change to
filesystem-specific options, the parameter data is NULL.  In this case,
kstrdup returns NULL (because it was passed NULL parameter), although no
out of memory condition exists.  The mount syscall then fails with
ENOMEM.

This patch fixes the bug.  We fail with ENOMEM only if data is non-NULL.

The patch also changes the call to replace_mount_options - if we didn't
pass any filesystem-specific options, we don't call
replace_mount_options (thus we don't erase existing reported options).

Fixes: ce657611baf9 ("hpfs: kstrdup() out of memory handling")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'upstream' of git://git.linux-mips.org/ralf/upstream-linus

Pull more MIPS updates from Ralf Baechle:
"This is the secondnd batch of MIPS patches for 4.7. Summary:

  CPS:
   - Copy EVA configuration when starting secondary VPs.

  EIC:
   - Clear Status IPL.

  Lasat:
   - Fix a few off by one bugs.

  lib:
   - Mark intrinsics notrace.  Not only are the intrinsics
     uninteresting, it would cause infinite recursion.

  MAINTAINERS:
   - Add file patterns for MIPS BRCM device tree bindings.
   - Add file patterns for mips device tree bindings.

  MT7628:
   - Fix MT7628 pinmux typos.
   - wled_an pinmux gpio.
   - EPHY LEDs pinmux support.

  Pistachio:
   - Enable KASLR

  VDSO:
   - Build microMIPS VDSO for microMIPS kernels.
   - Fix aliasing warning by building with `-fno-strict-aliasing' for
     debugging but also tracing them might result in recursion.

  Misc:
   - Add missing FROZEN hotplug notifier transitions.
   - Fix clk binding example for varioius PIC32 devices.
   - Fix cpu interrupt controller node-names in the DT files.
   - Fix XPA CPU feature separation.
   - Fix write_gc0_* macros when writing zero.
   - Add inline asm encoding helpers.
   - Add missing VZ accessor microMIPS encodings.
   - Fix little endian microMIPS MSA encodings.
   - Add 64-bit HTW fields and fix its configuration.
   - Fix sigreturn via VDSO on microMIPS kernel.
   - Lots of typo fixes.
   - Add definitions of SegCtl registers and use them"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (49 commits)
  MIPS: Add missing FROZEN hotplug notifier transitions
  MIPS: Build microMIPS VDSO for microMIPS kernels
  MIPS: Fix sigreturn via VDSO on microMIPS kernel
  MIPS: devicetree: fix cpu interrupt controller node-names
  MIPS: VDSO: Build with `-fno-strict-aliasing'
  MIPS: Pistachio: Enable KASLR
  MIPS: lib: Mark intrinsics notrace
  MIPS: Fix 64-bit HTW configuration
  MIPS: Add 64-bit HTW fields
  MAINTAINERS: Add file patterns for mips device tree bindings
  MAINTAINERS: Add file patterns for mips brcm device tree bindings
  MIPS: Simplify DSP instruction encoding macros
  MIPS: Add missing tlbinvf/XPA microMIPS encodings
  MIPS: Fix little endian microMIPS MSA encodings
  MIPS: Add missing VZ accessor microMIPS encodings
  MIPS: Add inline asm encoding helpers
  MIPS: Spelling fix lets -> let's
  MIPS: VR41xx: Fix typo
  MIPS: oprofile: Fix typo
  MIPS: math-emu: Fix typo
  ...

fs: fix binfmt_aout.c build error

Various builds (such as i386:allmodconfig) fail with

  fs/binfmt_aout.c:133:2: error: expected identifier or '(' before 'return'
  fs/binfmt_aout.c:134:1: error: expected identifier or '(' before '}' token

[ Oops. My bad, I had stupidly thought that "allmodconfig" covered this
  on x86-64 too, but it obviously doesn't.  Egg on my face.  - Linus ]

Fixes: 5d22fc25d4fc ("mm: remove more IS_ERR_VALUE abuses")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'hash' of git://ftp.sciencehorizons.net/linux

Pull string hash improvements from George Spelvin:
"This series does several related things:

   - Makes the dcache hash (fs/namei.c) useful for general kernel use.

     (Thanks to Bruce for noticing the zero-length corner case)

   - Converts the string hashes in <linux/sunrpc/svcauth.h> to use the
     above.

   - Avoids 64-bit multiplies in hash_64() on 32-bit platforms.  Two
     32-bit multiplies will do well enough.

   - Rids the world of the bad hash multipliers in hash_32.

     This finishes the job started in commit 689de1d6ca95 ("Minimal
     fix-up of bad hashing behavior of hash_64()")

     The vast majority of Linux architectures have hardware support for
     32x32-bit multiply and so derive no benefit from "simplified"
     multipliers.

     The few processors that do not (68000, h8/300 and some models of
     Microblaze) have arch-specific implementations added.  Those
     patches are last in the series.

   - Overhauls the dcache hash mixing.

     The patch in commit 0fed3ac866ea ("namei: Improve hash mixing if
     CONFIG_DCACHE_WORD_ACCESS") was an off-the-cuff suggestion.
     Replaced with a much more careful design that's simultaneously
     faster and better.  (My own invention, as there was noting suitable
     in the literature I could find.  Comments welcome!)

   - Modify the hash_name() loop to skip the initial HASH_MIX().  This
     would let us salt the hash if we ever wanted to.

   - Sort out partial_name_hash().

     The hash function is declared as using a long state, even though
     it's truncated to 32 bits at the end and the extra internal state
     contributes nothing to the result.  And some callers do odd things:

      - fs/hfs/string.c only allocates 32 bits of state
      - fs/hfsplus/unicode.c uses it to hash 16-bit unicode symbols not bytes

   - Modify bytemask_from_count to handle inputs of 1..sizeof(long)
     rather than 0..sizeof(long)-1.  This would simplify users other
     than full_name_hash"

  Special thanks to Bruce Fields for testing and finding bugs in v1.  (I
  learned some humbling lessons about "obviously correct" code.)

  On the arch-specific front, the m68k assembly has been tested in a
  standalone test harness, I've been in contact with the Microblaze
  maintainers who mostly don't care, as the hardware multiplier is never
  omitted in real-world applications, and I haven't heard anything from
  the H8/300 world"

* 'hash' of git://ftp.sciencehorizons.net/linux:
  h8300: Add <asm/hash.h>
  microblaze: Add <asm/hash.h>
  m68k: Add <asm/hash.h>
  <linux/hash.h>: Add support for architecture-specific functions
  fs/namei.c: Improve dcache hash function
  Eliminate bad hash multipliers from hash_32() and  hash_64()
  Change hash_64() return value to 32 bits
  <linux/sunrpc/svcauth.h>: Define hash_str() in terms of hashlen_string()
  fs/namei.c: Add hashlen_string() function
  Pull out string hash to <linux/stringhash.h>

h8300: Add <asm/hash.h>

This will improve the performance of hash_32() and hash_64(), but due
to complete lack of multi-bit shift instructions on H8, performance will
still be bad in surrounding code.

Designing H8-specific hash algorithms to work around that is a separate
project. (But if the maintainers would like to get in touch...)

Signed-off-by: George Spelvin <linux@sciencehorizons.net>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: uclinux-h8-devel@lists.sourceforge.jp

microblaze: Add <asm/hash.h>

Microblaze is an FPGA soft core that can be configured various ways.

If it is configured without a multiplier, the standard __hash_32()
will require a call to __mulsi3, which is a slow software loop.

Instead, use a shift-and-add sequence for the constant multiply.
GCC knows how to do this, but it's not as clever as some.

Signed-off-by: George Spelvin <linux@sciencehorizons.net>
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>

m68k: Add <asm/hash.h>

This provides a multiply by constant GOLDEN_RATIO_32 = 0x61C88647
for the original mc68000, which lacks a 32x32-bit multiply instruction.

Yes, the amount of optimization effort put in is excessive. :-)

Shift-add chain found by Yevgen Voronenko's Hcub algorithm at
http://spiral.ece.cmu.edu/mcm/gen.html

Signed-off-by: George Spelvin <linux@sciencehorizons.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: Philippe De Muyter <phdm@macq.eu>
Cc: linux-m68k@lists.linux-m68k.org

<linux/hash.h>: Add support for architecture-specific functions

This is just the infrastructure; there are no users yet.

This is modelled on CONFIG_ARCH_RANDOM; a CONFIG_ symbol declares
the existence of <asm/hash.h>.

That file may define its own versions of various functions, and define
HAVE_* symbols (no CONFIG_ prefix!) to suppress the generic ones.

Included is a self-test (in lib/test_hash.c) that verifies the basics.
It is NOT in general required that the arch-specific functions compute
the same thing as the generic, but if a HAVE_* symbol is defined with
the value 1, then equality is tested.

Signed-off-by: George Spelvin <linux@sciencehorizons.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: Philippe De Muyter <phdm@macq.eu>
Cc: linux-m68k@lists.linux-m68k.org
Cc: Alistair Francis <alistai@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: uclinux-h8-devel@lists.sourceforge.jp

fs/namei.c: Improve dcache hash function

Patch 0fed3ac866 improved the hash mixing, but the function is slower
than necessary; there's a 7-instruction dependency chain (10 on x86)
each loop iteration.

Word-at-a-time access is a very tight loop (which is good, because
link_path_walk() is one of the hottest code paths in the entire kernel),
and the hash mixing function must not have a longer latency to avoid
slowing it down.

There do not appear to be any published fast hash functions that:
1) Operate on the input a word at a time, and
2) Don't need to know the length of the input beforehand, and
3) Have a single iterated mixing function, not needing conditional
   branches or unrolling to distinguish different loop iterations.

One of the algorithms which comes closest is Yann Collet's xxHash, but
that's two dependent multiplies per word, which is too much.

The key insights in this design are:

1) Barring expensive ops like multiplies, to diffuse one input bit
   across 64 bits of hash state takes at least log2(64) = 6 sequentially
   dependent instructions.  That is more cycles than we'd like.
2) An operation like "hash ^= hash << 13" requires a second temporary
   register anyway, and on a 2-operand machine like x86, it's three
   instructions.
3) A better use of a second register is to hold a two-word hash state.
   With careful design, no temporaries are needed at all, so it doesn't
   increase register pressure.  And this gets rid of register copying
   on 2-operand machines, so the code is smaller and faster.
4) Using two words of state weakens the requirement for one-round mixing;
   we now have two rounds of mixing before cancellation is possible.
5) A two-word hash state also allows operations on both halves to be
   done in parallel, so on a superscalar processor we get more mixing
   in fewer cycles.

I ended up using a mixing function inspired by the ChaCha and Speck
round functions.  It is 6 simple instructions and 3 cycles per iteration
(assuming multiply by 9 can be done by an "lea" instruction):

x ^= *input++;
y ^= x; x = ROL(x, K1);
x += y; y = ROL(y, K2);
y *= 9;

Not only is this reversible, two consecutive rounds are reversible:
if you are given the initial and final states, but not the intermediate
state, it is possible to compute both input words.  This means that at
least 3 words of input are required to create a collision.

(It also has the property, used by hash_name() to avoid a branch, that
it hashes all-zero to all-zero.)

The rotate constants K1 and K2 were found by experiment.  The search took
a sample of random initial states (I used 1023) and considered the effect
of flipping each of the 64 input bits on each of the 128 output bits two
rounds later.  Each of the 8192 pairs can be considered a biased coin, and
adding up the Shannon entropy of all of them produces a score.

The best-scoring shifts also did well in other tests (flipping bits in y,
trying 3 or 4 rounds of mixing, flipping all 64*63/2 pairs of input bits),
so the choice was made with the additional constraint that the sum of the
shifts is odd and not too close to the word size.

The final state is then folded into a 32-bit hash value by a less carefully
optimized multiply-based scheme.  This also has to be fast, as pathname
components tend to be short (the most common case is one iteration!), but
there's some room for latency, as there is a fair bit of intervening logic
before the hash value is used for anything.

(Performance verified with "bonnie++ -s 0 -n 1536:-2" on tmpfs.  I need
a better benchmark; the numbers seem to show a slight dip in performance
between 4.6.0 and this patch, but they're too noisy to quote.)

Special thanks to Bruce fields for diligent testing which uncovered a
nasty fencepost error in an earlier version of this patch.

[checkpatch.pl formatting complaints noted and respectfully disagreed with.]

Signed-off-by: George Spelvin <linux@sciencehorizons.net>
Tested-by: J. Bruce Fields <bfields@redhat.com>

Eliminate bad hash multipliers from hash_32() and  hash_64()

The "simplified" prime multipliers made very bad hash functions, so get rid
of them.  This completes the work of 689de1d6ca.

To avoid the inefficiency which was the motivation for the "simplified"
multipliers, hash_64() on 32-bit systems is changed to use a different
algorithm.  It makes two calls to hash_32() instead.

drivers/media/usb/dvb-usb-v2/af9015.c uses the old GOLDEN_RATIO_PRIME_32
for some horrible reason, so it inherits a copy of the old definition.

Signed-off-by: George Spelvin <linux@sciencehorizons.net>
Cc: Antti Palosaari <crope@iki.fi>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>

Change hash_64() return value to 32 bits

That's all that's ever asked for, and it makes the return
type of hash_long() consistent.

It also allows (upcoming patch) an optimized implementation
of hash_64 on 32-bit machines.

I tried adding a BUILD_BUG_ON to ensure the number of bits requested
was never more than 32 (most callers use a compile-time constant), but
adding <linux/bug.h> to <linux/hash.h> breaks the tools/perf compiler
unless tools/perf/MANIFEST is updated, and understanding that code base
well enough to update it is too much trouble. I did the rest of an
allyesconfig build with such a check, and nothing tripped.

Signed-off-by: George Spelvin <linux@sciencehorizons.net>

<linux/sunrpc/svcauth.h>: Define hash_str() in terms of hashlen_string()

Finally, the first use of previous two patches: eliminate the
separate ad-hoc string hash functions in the sunrpc code.

Now hash_str() is a wrapper around hash_string(), and hash_mem() is
likewise a wrapper around full_name_hash().

Note that sunrpc code *does* call hash_mem() with a zero length, which
is why the previous patch needed to handle that in full_name_hash().
(Thanks, Bruce, for finding that!)

This also eliminates the only caller of hash_long which asks for
more than 32 bits of output.

The comment about the quality of hashlen_string() and full_name_hash()
is jumping the gun by a few patches; they aren't very impressive now,
but will be improved greatly later in the series.

Signed-off-by: George Spelvin <linux@sciencehorizons.net>
Tested-by: J. Bruce Fields <bfields@redhat.com>
Acked-by: J. Bruce Fields <bfields@redhat.com>
Cc: Jeff Layton <jlayton@poochiereds.net>
Cc: linux-nfs@vger.kernel.org

fs/namei.c: Add hashlen_string() function

We'd like to make more use of the highly-optimized dcache hash functions
throughout the kernel, rather than have every subsystem create its own,
and a function that hashes basic null-terminated strings is required
for that.

(The name is to emphasize that it returns both hash and length.)

It's actually useful in the dcache itself, specifically d_alloc_name().
Other uses in the next patch.

full_name_hash() is also tweaked to make it more generally useful:
1) Take a "char *" rather than "unsigned char *" argument, to
   be consistent with hash_name().
2) Handle zero-length inputs.  If we want more callers, we don't want
   to make them worry about corner cases.

Signed-off-by: George Spelvin <linux@sciencehorizons.net>

Pull out string hash to <linux/stringhash.h>

... so they can be used without the rest of <linux/dcache.h>

The hashlen_* macros will make sense next patch.

Signed-off-by: George Spelvin <linux@sciencehorizons.net>

Merge branch 'i2c/for-next' of git://git./linux/kernel/git/wsa/linux

Pull i2c fix from Wolfram Sang:
"A fix for a regression introduced yesterday.

  The regression didn't show up here locally because I did not have
  PAGE_POISONING enabled.  And buildbots discovered this only after it
  hit your tree.  Thanks to Dan for the quick response"

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: dev: use after free in detach

Merge tag 'chrome-platform' of git://git./linux/kernel/git/olof/chrome-platform

Pull chrome platform updates from Olof Johansson
"A handful of Chrome driver and binding changes this merge window:

   - a few patches to fix probing and configuration of pstore

   - a few patches adding Elan touchpad registration on a few devices

   - EC changes: a security fix dealing with max message sizes and
     addition of compat_ioctl support.

   - keyboard backlight control support

  There was also an accidential duplicate registration of trackpads on
  'Leon', which was reverted just recently"

* tag 'chrome-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform:
  Revert "platform/chrome: chromeos_laptop: Add Leon Touch"
  platform/chrome: chromeos_laptop - Add Elan touchpad for Wolf
  platform/chrome: chromeos_laptop - Add elan trackpad option for C720
  platform/chrome: cros_ec_dev - Populate compat_ioctl
  platform/chrome: cros_ec_lightbar - use name instead of ID to hide lightbar attributes
  platform/chrome: cros_ec_dev - Fix security issue
  platform/chrome: Add Chrome OS keyboard backlight LEDs support
  platform/chrome: use to_platform_device()
  platform/chrome: pstore: Move to larger record size.
  platform/chrome: pstore: probe for ramoops buffer using acpi
  platform/chrome: chromeos_laptop: Add Leon Touch

Merge tag 'sound-4.7-rc1-2' of git://git./linux/kernel/git/tiwai/sound

Pull more sound updates from Takashi Iwai:
"This is the second update round for 4.7-rc1.  Most of changes are
  about the pending ASoC updates and fixes, including a few new drivers.
  Below are some highlights:

  ASoC:
   - New drivers for MAX98371 and TAS5720
   - SPI support for TLV320AIC32x4, along with the module split
   - TDM support for STI Uniperf IPs
   - Remaining topology API fixes / updates

  HDA:
   - A couple of Dell quirks and new Realtek codec support"

* tag 'sound-4.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (63 commits)
  ALSA: hda - Fix headset mic detection problem for one Dell machine
  spi: spi-ep93xx: Fix the PTR_ERR() argument
  ALSA: hda/realtek - Add support for ALC295/ALC3254
  ASoC: kirkwood: fix build failure
  ALSA: hda - Fix headphone noise on Dell XPS 13 9360
  ASoC: ak4642: Enable cache usage to fix crashes on resume
  ASoC: twl6040: Disconnect AUX output pads on digital mute
  ASoC: tlv320aic32x4: Properly implement the positive and negative pins into the mixers
  rcar: src: skip disabled-SRC nodes
  ASoC: max98371 Remove duplicate entry in max98371_reg
  ASoC: twl6040: Select LPPLL during standby
  ASoC: rsnd: don't use prohibited number to PDMACHCRn.SRS
  ASoC: simple-card: Add pm callbacks to platform driver
  ASoC: pxa: Fix module autoload for platform drivers
  ASoC: topology: Fix memory leak in widget creation
  ASoC: Add max98371 codec driver
  ASoC: rsnd: count .probe/.remove for rsnd_mod_call()
  ASoC: topology: Check size mismatch of ABI objects before parsing
  ASoC: topology: Check failure to create a widget
  ASoC: add support for TAS5720 digital amplifier
  ...

Merge branch 'for-next' of git://git./linux/kernel/git/nab/target-pending

Pull SCSI target updates from Nicholas Bellinger:
"Here are the outstanding target pending updates for v4.7-rc1.

  The highlights this round include:

   - Allow external PR/ALUA metadata path be defined at runtime via top
     level configfs attribute (Lee)
   - Fix target session shutdown bug for ib_srpt multi-channel (hch)
   - Make TFO close_session() and shutdown_session() optional (hch)
   - Drop se_sess->sess_kref + convert tcm_qla2xxx to internal kref
     (hch)
   - Add tcm_qla2xxx endpoint attribute for basic FC jammer (Laurence)
   - Refactor iscsi-target RX/TX PDU encode/decode into common code
     (Varun)
   - Extend iscsit_transport with xmit_pdu, release_cmd, get_rx_pdu,
     validate_parameters, and get_r2t_ttt for generic ISO offload
     (Varun)
   - Initial merge of cxgb iscsi-segment offload target driver (Varun)

  The bulk of the changes are Chelsio's new driver, along with a number
  of iscsi-target common code improvements made by Varun + Co along the
  way"

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (29 commits)
  iscsi-target: Fix early sk_data_ready LOGIN_FLAGS_READY race
  cxgbit: Use type ISCSI_CXGBIT + cxgbit tpg_np attribute
  iscsi-target: Convert transport drivers to signal rdma_shutdown
  iscsi-target: Make iscsi_tpg_np driver show/store use generic code
  tcm_qla2xxx Add SCSI command jammer/discard capability
  iscsi-target: graceful disconnect on invalid mapping to iovec
  target: need_to_release is always false, remove redundant check and kfree
  target: remove sess_kref and ->shutdown_session
  iscsi-target: remove usage of ->shutdown_session
  tcm_qla2xxx: introduce a private sess_kref
  target: make close_session optional
  target: make ->shutdown_session optional
  target: remove acl_stop
  target: consolidate and fix session shutdown
  cxgbit: add files for cxgbit.ko
  iscsi-target: export symbols
  iscsi-target: call complete on conn_logout_comp
  iscsi-target: clear tx_thread_active
  iscsi-target: add new offload transport type
  iscsi-target: use conn_transport->transport_type in text rsp
  ...

Merge tag 'for-linus' of git://git./linux/kernel/git/dledford/rdma

Pull more rdma updates from Doug Ledford:
"This is the second group of code for the 4.7 merge window.  It looks
  large, but only in one sense.  I'll get to that in a minute.  The list
  of changes here breaks down as follows:

   - Dynamic counter infrastructure in the IB drivers

     This is a sysfs based code to allow free form access to the
     hardware counters RDMA devices might support so drivers don't need
     to code this up repeatedly themselves

   - SendOnlyFullMember multicast support

   - IB router support

   - A couple misc fixes

   - The big item on the list: hfi1 driver updates, plus moving the hfi1
     driver out of staging

  There was a group of 15 patches in the hfi1 list that I thought I had
  in the first pull request but they weren't.  So that added to the
  length of the hfi1 section here.

  As far as these go, everything but the hfi1 is pretty straight
  forward.

  The hfi1 is, if you recall, the driver that Al had complaints about
  how it used the write/writev interfaces in an overloaded fashion.  The
  write portion of their interface behaved like the write handler in the
  IB stack proper and did bi-directional communications.  The writev
  interface, on the other hand, only accepts SDMA request structures.
  The completions for those structures are sent back via an entirely
  different event mechanism.

  With the security patch, we put security checks on the write
  interface, however, we also knew they would be going away soon.  Now,
  we've converted the write handler in the hfi1 driver to use ioctls
  from the IB reserved magic area for its bidirectional communications.
  With that change, Intel has addressed all of the items originally on
  their TODO when they went into staging (as well as many items added to
  the list later).

  As such, I moved them out, and since they were the last item in the
  staging/rdma directory, and I don't have immediate plans to use the
  staging area again, I removed the staging/rdma area.

  Because of the move out of staging, as well as a series of 5 patches
  in the hfi1 driver that removed code people thought should be done in
  a different way and was optional to begin with (a snoop debug
  interface, an eeprom driver for an eeprom connected directory to their
  hfi1 chip and not via an i2c bus, and a few other things like that),
  the line count, especially the removal count, is high"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (56 commits)
  staging/rdma: Remove the entire rdma subdirectory of staging
  IB/core: Make device counter infrastructure dynamic
  IB/hfi1: Fix pio map initialization
  IB/hfi1: Correct 8051 link parameter settings
  IB/hfi1: Update pkey table properly after link down or FM start
  IB/rdamvt: Fix rdmavt s_ack_queue sizing
  IB/rdmavt: Max atomic value should be a u8
  IB/hfi1: Fix hard lockup due to not using save/restore spin lock
  IB/hfi1: Add tracing support for send with invalidate opcode
  IB/hfi1, qib: Add ieth to the packet header definitions
  IB/hfi1: Move driver out of staging
  IB/hfi1: Do not free hfi1 cdev parent structure early
  IB/hfi1: Add trace message in user IOCTL handling
  IB/hfi1: Remove write(), use ioctl() for user cmds
  IB/hfi1: Add ioctl() interface for user commands
  IB/hfi1: Remove unused user command
  IB/hfi1: Remove snoop/diag interface
  IB/hfi1: Remove EPROM functionality from data device
  IB/hfi1: Remove UI char device
  IB/hfi1: Remove multiple device cdev
  ...

Revert "platform/chrome: chromeos_laptop: Add Leon Touch"

This reverts commit bff3c624dc7261a084a4d25a0b09c3fb0fec872a.

Board "Leon" is otherwise known as "Toshiba CB35" and we already have
the entry that supports that board as of this commit :
963cb6f platform/chrome: chromeos_laptop - Add Toshiba CB35 Touch

Remove this duplicate.

Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

i2c: dev: use after free in detach

The call to put_i2c_dev() frees "i2c_dev" so there is a use after
free when we call cdev_del(&i2c_dev->cdev).

Fixes: d6760b14d4a1 ('i2c: dev: switch from register_chrdev to cdev API')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

MIPS: Add missing FROZEN hotplug notifier transitions

The corresponding FROZEN hotplug notifier transitions used on
suspend/resume are ignored. Therefore the switch case action argument
is masked with the frozen hotplug notifier transition mask.

Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: rt@linutronix.de
Patchwork: https://patchwork.linux-mips.org/patch/13351/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Build microMIPS VDSO for microMIPS kernels

MicroMIPS kernels may be expected to run on microMIPS only cores which
don't support the normal MIPS instruction set, so be sure to pass the
-mmicromips flag through to the VDSO cflags.

Fixes: ebb5e78cc634 ("MIPS: Initial implementation of a VDSO")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.4.x-
Patchwork: https://patchwork.linux-mips.org/patch/13349/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Fix sigreturn via VDSO on microMIPS kernel

In microMIPS kernels, handle_signal() sets the isa16 mode bit in the
vdso address so that the sigreturn trampolines (which are offset from
the VDSO) get executed as microMIPS.

However commit ebb5e78cc634 ("MIPS: Initial implementation of a VDSO")
changed the offsets to come from the VDSO image, which already have the
isa16 mode bit set correctly since they're extracted from the VDSO
shared library symbol table.

Drop the isa16 mode bit handling from handle_signal() to fix sigreturn
for cores which support both microMIPS and normal MIPS. This doesn't fix
microMIPS only cores, since the VDSO is still built for normal MIPS, but
thats a separate problem.

Fixes: ebb5e78cc634 ("MIPS: Initial implementation of a VDSO")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.4.x-
Patchwork: https://patchwork.linux-mips.org/patch/13348/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: devicetree: fix cpu interrupt controller node-names

Here is the quote from [1]:

    The unit-address must match the first address specified
    in the reg property of the node. If the node has no reg property,
    the @ and unit-address must be omitted and the node-name alone
    differentiates the node from other nodes at the same level

This patch adjusts MIPS dts-files and devicetree binding
documentation in accordance with [1].

    [1] Power.org(tm) Standard for Embedded Power Architecture(tm)
        Platform Requirements (ePAPR). Version 1.1 – 08 April 2011.
        Chapter 2.2.1.1 Node Name Requirements

Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13345/
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: VDSO: Build with `-fno-strict-aliasing'

Avoid an aliasing issue causing a build error in VDSO:

In file included from include/linux/srcu.h:34:0,
                 from include/linux/notifier.h:15,
                 from ./arch/mips/include/asm/uprobes.h:9,
                 from include/linux/uprobes.h:61,
                 from include/linux/mm_types.h:13,
                 from ./arch/mips/include/asm/vdso.h:14,
                 from arch/mips/vdso/vdso.h:27,
                 from arch/mips/vdso/gettimeofday.c:11:
include/linux/workqueue.h: In function 'work_static':
include/linux/workqueue.h:186:2: error: dereferencing type-punned pointer will break strict-aliasing rules [-Werror=strict-aliasing]
  return *work_data_bits(work) & WORK_STRUCT_STATIC;
  ^
cc1: all warnings being treated as errors
make[2]: *** [arch/mips/vdso/gettimeofday.o] Error 1

with a CONFIG_DEBUG_OBJECTS_WORK configuration and GCC 5.2.0.  Include
`-fno-strict-aliasing' along with compiler options used, as required for
kernel code, fixing a problem present since the introduction of VDSO
with commit ebb5e78cc634 ("MIPS: Initial implementation of a VDSO").

Thanks to Tejun for diagnosing this properly!

Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Fixes: ebb5e78cc634 ("MIPS: Initial implementation of a VDSO")
Cc: Tejun Heo <tj@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # v4.3+
Patchwork: https://patchwork.linux-mips.org/patch/13357/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Pistachio: Enable KASLR

Allow KASLR to be selected on Pistachio based systems. Tested on a
Creator Ci40.

Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13356/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: lib: Mark intrinsics notrace

On certain MIPS32 devices, the ftrace tracer "function_graph" uses
__lshrdi3() during the capturing of trace data. ftrace then attempts to
trace __lshrdi3() which leads to infinite recursion and a stack overflow.
Fix this by marking __lshrdi3() as notrace. Mark the other compiler
intrinsics as notrace in case the compiler decides to use them in the
ftrace path.

Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: <linux-mips@linux-mips.org>
Cc: <linux-kernel@vger.kernel.org>
Cc: <stable@vger.kernel.org> # 4.2.x-
Patchwork: https://patchwork.linux-mips.org/patch/13354/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Fix 64-bit HTW configuration

The Hardware page Table Walker (HTW) is being misconfigured on 64-bit
kernels. The PWSize.PS (pointer size) bit determines whether pointers
within directories are loaded as 32-bit or 64-bit addresses, but was
never being set to 1 for 64-bit kernels where the unsigned long in pgd_t
is 64-bits wide.

This actually reduces rather than improves performance when the HTW is
enabled on P6600 since the HTW is initiated lots, but walks are all
aborted due I think to bad intermediate pointers.

Since we were already taking the width of the PTEs into account by
setting PWSize.PTEW, which is the left shift applied to the page table
index *in addition to* the native pointer size, we also need to reduce
PTEW by 1 when PS=1. This is done by calculating PTEW based on the
relative size of pte_t compared to pgd_t.

Finally in order for the HTW to be used when PS=1, the appropriate
XK/XS/XU bits corresponding to the different 64-bit segments need to be
set in PWCtl. We enable only XU for now to enable walking for XUSeg.

Supporting walking for XKSeg would be a bit more involved so is left for
a future patch. It would either require the use of a per-CPU top level
base directory if supported by the HTW (a bit like pgd_current but with
a second entry pointing at swapper_pg_dir), or the HTW would prepend bit
63 of the address to the global directory index which doesn't really
match how we split user and kernel page directories.

Fixes: cab25bc7537b ("MIPS: Extend hardware table walking support to MIPS64")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13364/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Add 64-bit HTW fields

Add field definitions for some of the 64-bit specific Hardware page
Table Walker (HTW) register fields in PWSize and PWCtl, in preparation
for fixing the 64-bit HTW configuration.

Also print these fields out along with the others in print_htw_config().

Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13363/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MAINTAINERS: Add file patterns for mips device tree bindings

Submitters of device tree binding documentation may forget to CC
the subsystem maintainer if this is missing.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13340/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MAINTAINERS: Add file patterns for mips brcm device tree bindings

Submitters of device tree binding documentation may forget to CC
the subsystem maintainer if this is missing.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13339/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Simplify DSP instruction encoding macros

Simplify the DSP instruction wrapper macros which use explicit encodings
for microMIPS and normal MIPS by using the new encoding macros and
removing duplication.

To me this makes it easier to read since it is much shorter, but it also
ensures .insn is used, preventing objdump disassembling the microMIPS
code as normal MIPS.

Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13314/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Add missing tlbinvf/XPA microMIPS encodings

Hardcoded MIPS instruction encodings are provided for tlbinvf, mfhc0 &
mthc0 instructions, but microMIPS encodings are missing. I doubt any
microMIPS cores exist at present which support these instructions, but
the microMIPS encodings exist, and microMIPS cores may support them in
the future. Add the missing microMIPS encodings using the new macros.

Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13313/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Fix little endian microMIPS MSA encodings

When the toolchain doesn't support MSA we encode MSA instructions
explicitly in assembly. Unfortunately we use .word for both MIPS and
microMIPS encodings which is wrong, since 32-bit microMIPS instructions
are made up from a pair of halfwords.

- The most significant halfword always comes first, so for little endian
  builds the halves will be emitted in the wrong order.

- 32-bit alignment isn't guaranteed, so the assembler may insert a
  16-bit nop instruction to pad the instruction stream to a 32-bit
  boundary.

Use the new instruction encoding macros to encode microMIPS MSA
instructions correctly.

Fixes: d96cc3d1ec5d ("MIPS: Add microMIPS MSA support.")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <Paul.Burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13312/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Add missing VZ accessor microMIPS encodings

Toolchains may be used which support microMIPS but not VZ instructions
(i.e. binutis 2.22 & 2.23), so extend the explicitly encoded versions of
the guest COP0 register & guest TLB access macros to support microMIPS
encodings too, using the new macros.

This prevents non-microMIPS instructions being executed in microMIPS
mode during CPU probe on cores supporting VZ (e.g. M5150), which cause
reserved instruction exceptions early during boot.

Fixes: bad50d79255a ("MIPS: Fix VZ probe gas errors with binutils <2.24")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13311/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Add inline asm encoding helpers

To allow simplification of macros which use inline assembly to
explicitly encode instructions, add a few simple abstractions to
mipsregs.h which expand to specific microMIPS or normal MIPS encodings
depending on what type of kernel is being built:

_ASM_INSN_IF_MIPS(_enc) : Emit a 32bit MIPS instruction if microMIPS is
                          not enabled.
_ASM_INSN32_IF_MM(_enc) : Emit a 32bit microMIPS instruction if enabled.
_ASM_INSN16_IF_MM(_enc) : Emit a 16bit microMIPS instruction if enabled.

The macros can be used one after another since the MIPS / microMIPS
macros are mutually exclusive, for example:

__asm__ __volatile__(
        ".set push\n\t"
        ".set noat\n\t"
        "# mfgc0 $1, $%1, %2\n\t"
        _ASM_INSN_IF_MIPS(0x40610000 | %1 << 11 | %2)
        _ASM_INSN32_IF_MM(0x002004fc | %1 << 16 | %2 << 11)
        "move %0, $1\n\t"
        ".set pop"
        : "=r" (__res)
        : "i" (source), "i" (sel));

Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13310/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Spelling fix lets -> let's

As noticed by Sergei in the discussion of Andrea Gelmini's patch series.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

MIPS: VR41xx: Fix typo

Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: trivial@kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13338/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: oprofile: Fix typo

Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: rric@kernel.org
Cc: linux-mips@linux-mips.org
Cc: trivial@kernel.org
Cc: oprofile-list@lists.sf.net
Patchwork: https://patchwork.linux-mips.org/patch/13334/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: math-emu: Fix typo

Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: macro@imgtec.com
Cc: trivial@kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13333/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: lib: Fix typo

Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: trivial@kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13331/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: kernel: Fix typo

Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: paul.burton@imgtec.com
Cc: macro@imgtec.com
Cc: james.hogan@imgtec.com
Cc: jslaby@suse.cz
Cc: adam.buchbinder@gmail.com
Cc: trivial@kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13330/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: R6: Fix typo

Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: macro@imgtec.com
Cc: paul.burton@imgtec.com
Cc: Leonid.Yegoshin@imgtec.com
Cc: trivial@kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13329/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: IP22/IP28: Fix typo

Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: adam.buchbinder@gmail.com
Cc: trivial@kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13328/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Cavium: Fix typo

Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: david.daney@cavium.com
Cc: janne.huttunen@nokia.com
Cc: aaro.koskinen@nokia.com
Cc: trivial@kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13324/
Patchwork: https://patchwork.linux-mips.org/patch/13325/
Patchwork: https://patchwork.linux-mips.org/patch/13326/
Patchwork: https://patchwork.linux-mips.org/patch/13327/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: MT: Fix typo

Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: linux-mips@linux-mips.org
Cc: trivial@kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13323/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Loongson64: Fix typo

Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: chenhc@lemote.com
Cc: viresh.kumar@linaro.org
Cc: linux-mips@linux-mips.org
Cc: trivial@kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13322/
Patchwork: https://patchwork.linux-mips.org/patch/13332/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: IP32: Fix typo

Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: trivial@kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13321/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: IP27: Fix typo

Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: trivial@kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13320/
Patchwork: https://patchwork.linux-mips.org/patch/13335/
Patchwork: https://patchwork.linux-mips.org/patch/13336/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: BCM63xx: Fix typo

Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: trivial@kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13319/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Alchemy: Fix typo

Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: trivial@kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13318/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: hazards.h: Fix typo

Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: chenhc@lemote.com
Cc: james.hogan@imgtec.com
Cc: linux-mips@linux-mips.org
Cc: trivial@kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13317/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Lasat: A couple off by one bugs in picvue_proc.c

These should be ">=" instead of ">" or we go past the end of the
pvc_lines[] array.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: linux-mips@linux-mips.org
Cc: kernel-janitors@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/6124/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ralink: add MT7628 EPHY LEDs pinmux support

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Cc: john@phrozen.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13308/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ralink: fix MT7628 wled_an pinmux gpio

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Cc: john@phrozen.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13307/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: ralink: fix MT7628 pinmux typos

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Cc: john@phrozen.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13306/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Fix write_gc0_* macros when writing zero

The versions of the __write_{32,64}bit_gc0_register() macros for when
there is no virt support in the assembler use the "J" inline asm
constraint to allow integer zero, but this needs to be accompanied by
the "z" formatting string so that it turns into $0. Fix both macros to
do this.

Fixes: bad50d79255a ("MIPS: Fix VZ probe gas errors with binutils <2.24")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13289/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: CPS: Copy EVA configuration when starting secondary VPs.

When starting secondary VPEs which support EVA and the SegCtl registers,
copy the memory segmentation configuration from the running VPE to ensure
that all VPEs in the core have a consistent virtual memory map.

The EVA configuration of secondary cores is dealt with when starting the
core via the CM.

Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13291/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Add definitions of SegCtl registers and use them

The SegCtl registers are standard for MIPSr3..MIPSr5. Add definitions of
these registers and use them rather than constants

Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Chris Packham <judge.packham@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13290/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

dt/bindings: Correct clk binding example for PIC32 gpio.

Update binding example based on new clock binding scheme.
[1] Documentation/devicetree/bindings/clock/microchip,pic32.txt

Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: linux-gpio@vger.kernel.org
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13270/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

dt/bindings: Correct clk binding example for PIC32 WDT.

Update binding example based on new clock binding scheme.
[1] Documentation/devicetree/bindings/clock/microchip,pic32.txt

Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Joshua Henderson <digitalpeer@digitalpeer.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13269/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

dt/bindings: Correct clk binding example for PIC32 DMT.

Update binding example based on new clock binding scheme.
[1] Documentation/devicetree/bindings/clock/microchip,pic32.txt

Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Joshua Henderson <digitalpeer@digitalpeer.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13268/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

dt/bindings: Correct clk binding example for PIC32 serial.

Update binding example based on new clock binding scheme.
[1] Documentation/devicetree/bindings/clock/microchip,pic32.txt

Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Joshua Henderson <digitalpeer@digitalpeer.com>
Cc: Andrei Pistirica <andrei.pistirica@microchip.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13267/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

dt/bindings: Correct clk binding example for PIC32 pinctrl

Update binding example based on new clock binding scheme.
[1] Documentation/devicetree/bindings/clock/microchip,pic32.txt

Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Joshua Henderson <digitalpeer@digitalpeer.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13266/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

dt/bindings: Correct clk binding example for PIC32 SDHCI

Update binding example based on new clock binding documentation.
[1] Documentation/devicetree/bindings/clock/microchip,pic32.txt

Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Joshua Henderson <digitalpeer@digitalpeer.com>
Cc: Andrei Pistirica <andrei.pistirica@microchip.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13265/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Fix incomplete separation of XPA CPU feature

Commit 12822570a29b ("MIPS: Separate XPA CPU feature into LPA and MVH")
wasn't fully applied, possibly due to a conflict with commit
f270d881fa55 ("MIPS: Detect MIPSr6 Virtual Processor support"). This
left decode_config5() referring to the non-existent MIPS_CPU_XPA, which
breaks the build when XPA is enabled:

arch/mips/kernel/cpu-probe.c In function ‘decode_config5’:
arch/mips/kernel/cpu-probe.c:838:17: error: ‘MIPS_CPU_XPA’ undeclared (first use in this function)
c->options |= MIPS_CPU_XPA;
^

Apply the missing hunk, dropping the CONFIG_XPA ifdef and setting the
MIPS_CPU_MVH option when Config5.MVH is set.

Fixes: 12822570a29b ("MIPS: Separate XPA CPU feature into LPA and MVH")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Link: https://patchwork.linux-mips.org/patch/13112/
Patchwork: https://patchwork.linux-mips.org/patch/13277/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

irqchip: mips-gic: Setup EIC mode on each CPU if it's in use

When EIC mode is in use (cpu_has_veic is true) enable it on each CPU
during GIC initialisation. Otherwise there may be a mismatch between the
hardware default interrupt model & that expected by the kernel.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Matt Redfearn <matt.redfearn@imgtec.com>
Tested-by: Matt Redfearn <matt.redfearn@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13274/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: smp-cps: Clear Status IPL field when using EIC

When using an external interrupt controller (EIC) the interrupt mask
bits in the cop0 Status register are reused for the Interrupt Priority
Level, and any interrupts with a priority lower than the field will be
ignored. Clear the field to 0 by default such that all interrupts are
serviced.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Matt Redfearn <matt.redfearn@imgtec.com>
Tested-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Qais Yousef <qsyousef@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13273/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

MIPS: Clear Status IPL field when using EIC

When using an external interrupt controller (EIC) the interrupt mask
bits in the cop0 Status register are reused for the Interrupt Priority
Level, and any interrupts with a priority lower than the field will be
ignored. Clear the field to 0 by default such that all interrupts are
serviced. Without doing so we default to arbitrarily ignoring all or
some subset of interrupts.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Matt Redfearn <matt.redfearn@imgtec.com>
Tested-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Joe Perches <joe@perches.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13272/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input

Pull more input subsystem updates from Dmitry Torokhov:
"Just a few more driver fixes; new drivers will be coming in the next
  merge window"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: pwm-beeper - fix - scheduling while atomic
  Input: xpad - xbox one elite controller support
  Input: xpad - add more third-party controllers
  Input: xpad - prevent spurious input from wired Xbox 360 controllers
  Input: xpad - move pending clear to the correct location
  Input: uinput - handle compat ioctl for UI_SET_PHYS

Merge branch 'i2c/for-next' of git://git./linux/kernel/git/wsa/linux

Pull more i2c updates from Wolfram Sang:
"Here is the second pull request from I2C for this merge window:

   - one new feature (which nearly fell through the cracks): i2c-dev
     does now use the cdev API so it can handle >256 minors.  Seems
     people do need that.

   - two fixes for the just added DMA feature for i2c-rcar

   - some typo fixes"

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: dev: don't start function name with 'return'
  i2c: dev: switch from register_chrdev to cdev API
  i2c: xlr: rename ARCH_TANGOX to ARCH_TANGO
  i2c: at91: change log when dma configuration fails
  misc: at24: Fix typo in at24 header file
  i2c: rcar: should depend on HAS_DMA
  i2c: rcar: use dma_request_chan()

Merge branch 'for-linus-4.7-rc1' of git://git./linux/kernel/git/rw/uml

Pull UML updates from Richard Weinberger:
"This contains a nice FPU fixup from Eli Cooper for UML"

* 'for-linus-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
  um: add extended processor state save/restore support
  um: extend fpstate to _xstate to support YMM registers
  um: fix FPU state preservation around signal handlers

Merge tag 'upstream-4.7-rc1' of git://git.infradead.org/linux-ubifs

Pull UBI/UBIFS updates from Richard Weinberger:
"This contains mostly cleanups and minor improvements of UBI and UBIFS"

* tag 'upstream-4.7-rc1' of git://git.infradead.org/linux-ubifs:
  ubifs: ubifs_dump_inode: Fix dumping field bulk_read
  UBI: Fix static volume checks when Fastmap is used
  UBI: Set free_count to zero before walking through erase list
  UBI: Silence an unintialized variable warning
  UBI: Clean up return in ubi_remove_volume()
  UBI: Modify wrong comment in ubi_leb_map function.
  UBI: Don't read back all data in ubi_eba_copy_leb()
  UBI: Add ro-mode sysfs attribute