Tom Rini [Tue, 20 Aug 2013 12:53:49 +0000 (08:53 -0400)]
TI:armv7: Re-order slightly the generic CONFIG options, expand related comments
Re-group the general options to note things that can be removed safely
to reduce binary size when not required, and expand the comment about
what commands we do include to note it could be replaced with a specific
list of required one. While at it, move the CMD parts of various
blocks IP to the end of the list for consistency.
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Tue, 20 Aug 2013 12:53:48 +0000 (08:53 -0400)]
am335x_evm: Regroup USB options
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Tue, 20 Aug 2013 12:53:47 +0000 (08:53 -0400)]
am335x_evm: Add comment by SPL SPI support
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Tue, 20 Aug 2013 12:53:46 +0000 (08:53 -0400)]
TI:am335x: Better comment and organize the networking related options
While in here, drop CONFIG_BOOTP_DEFAULT as it is unused in the code.
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Tue, 20 Aug 2013 12:53:45 +0000 (08:53 -0400)]
omap5: Expand CONFIG_SPL_MAX_SIZE and comment upon SRAM_SCRATCH_SPACE_ADDR
After examining both TRMs and doing some experimentation, we can rely on
using the start of the download area for CONFIG_SPL_TEXT_BASE and then
move SRAM_SCRATCH_SPACE_ADDR up, just like am335x. This is required for
peripheral boot modes such as UART.
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Tue, 20 Aug 2013 12:53:44 +0000 (08:53 -0400)]
TI:armv7: Move CONFIG_SPL_LIBDISK_SUPPORT to MMC section
We only need this library when we're doing "disk" access to MMC/SD.
Update comment around the rest of CONFIG_SPL_LIB* to note that the
others are always required.
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Tue, 20 Aug 2013 12:53:43 +0000 (08:53 -0400)]
am33xx: Correct and expand comments on CONFIG_SPL_MAX_SIZE
We had been allowing the max size to be larger than actually allowed by
the ROM. Expand the commentary here to explain why we set these
locations.
Signed-off-by: Tom Rini <trini@ti.com>
Javier Martinez Canillas [Sun, 11 Aug 2013 16:20:00 +0000 (18:20 +0200)]
ARM: igep00x0.h: Enable raw initrd support
Now that IGEP base boards default environment use
the bootz command to boot a zImage instead of a
uImage, it makes sense to add support to supply a
raw initrd image to the kernel if needed.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Albert ARIBAUD [Sat, 10 Aug 2013 17:03:59 +0000 (19:03 +0200)]
arm: omap3: fix SRAM copy and execution sequence
Fix size calculation in copy of go_to_speed into SRAM.
Use SRAM_CLK_CODE in call to SRAM-based go_to_speed.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Taras Kondratiuk [Tue, 6 Aug 2013 12:18:51 +0000 (15:18 +0300)]
ARM: OMAP4460: sdp: Limit TPS mux config to 4460
TPS mux config is 4460 specific, so it should be limited to 4460 only.
Signed-off-by: Taras Kondratiuk <taras@ti.com>
Lubomir Popov [Tue, 6 Aug 2013 12:18:50 +0000 (15:18 +0300)]
ARM: OMAP4470: Add Elpida EDB8164B3PF memory configuration
OMAP4470 SDP SoM has EDB8164B3PF PoP memory on board.
This memory has 4Gb x 2CS = 8Gb configuration.
Add configuration for runtime calculation and precalculated cases.
Patch is based on a draft Lubomir's patch [1].
[1] http://lists.denx.de/pipermail/u-boot/2013-April/150851.html
Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
[taras@ti.com: cleaned up patch and fixed precalculated values]
Signed-off-by: Taras Kondratiuk <taras@ti.com>
Taras Kondratiuk [Tue, 6 Aug 2013 12:18:49 +0000 (15:18 +0300)]
ARM: OMAP4470: Add voltage and dpll data
OMAP4470 reference design uses TWL6032 PMIC
with a following connection scheme:
VDD_CORE = TWL6032 SMPS2
VDD_MPU = TWL6032 SMPS1
VDD_IVA = TWL6032 SMPS5
Set voltage and frequency values according to
OMAP4470 Data Manual Operating Condition Addendum v0.7
Signed-off-by: Taras Kondratiuk <taras@ti.com>
Taras Kondratiuk [Tue, 6 Aug 2013 12:18:48 +0000 (15:18 +0300)]
ARM: OMAP4470: Add OMAP4470 identification
Signed-off-by: Taras Kondratiuk <taras@ti.com>
Oleksandr Tyshchenko [Tue, 6 Aug 2013 11:03:27 +0000 (14:03 +0300)]
sdp4430: Initialize board id using CONFIG_MACH_TYPE
Use CONFIG_MACH_TYPE generic macro to set the machine type
number in the common arm code instead of setting it in the
board code.
Signed-off-by: Oleksandr Tyshchenko <oleksandr.tyshchenko@ti.com>
Minkyu Kang [Tue, 6 Aug 2013 11:57:53 +0000 (20:57 +0900)]
arm: goni: remove config.mk file
Since config.mk is deprecated, remove this file,
and move CONFIG_SYS_TEXT_BASE define to config file.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Minkyu Kang [Tue, 6 Aug 2013 11:57:03 +0000 (20:57 +0900)]
arm: smdkc100: remove config.mk file
Since config.mk is deprecated, remove this file,
and move CONFIG_SYS_TEXT_BASE define to config file.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cc: Wolfgang Denk <wd@denx.de>
Tom Rini [Tue, 27 Aug 2013 14:56:18 +0000 (10:56 -0400)]
omap5: Correct include order, drop CONFIG_SYS_PROMPT define
With the new include structure for TI platforms, we need to not define
our own CONFIG_SYS_PROMPT and also need to include
<configs/omap5_common.h> much sooner, so do both of these. Also drop
the unused CONFIG_NET_MULTI
Signed-off-by: Tom Rini <trini@ti.com>
Gerlando Falauto [Tue, 27 Aug 2013 13:43:57 +0000 (19:13 +0530)]
cmd_sf: let "sf update" preserve the final part of the last sector
Since "sf update" erases the last block as a whole, but only rewrites
the meaningful initial part of it, the rest would be left erased,
potentially erasing meaningful information.
So, as a safety measure, have it rewrite the original content.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Marek Vasut [Mon, 26 Aug 2013 15:45:23 +0000 (17:45 +0200)]
spi: mxs_spi: Configure chipselect after block reset
The chipselect must be written into the CTRL0 register after the SSP
block is reset, otherwise the block will always use ChipSelect #0.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Tom Rini [Tue, 27 Aug 2013 13:49:43 +0000 (09:49 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-usb
Chander Kashyap [Thu, 25 Jul 2013 12:58:52 +0000 (18:28 +0530)]
CONFIG: EXYNOS5: Replace misnomer SMDK5250 with EXYNOS5250 and update Makefiles
Update the Makefiles so that all boards can use the same spl generation tool
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Heiko Schocher [Fri, 23 Aug 2013 07:39:16 +0000 (09:39 +0200)]
i2c: fix i2c dev command for not using new framework
i2c dev command does not work anymore for legacy drivers
because a check is executed that is valid only
in the new framework.
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Stefano Babic <sbabic@denx.de>
Jim Lin [Mon, 26 Aug 2013 12:21:09 +0000 (20:21 +0800)]
console: usb: kbd: To fix slow TFTP booting
TFTP booting is slow when a USB keyboard is installed and
stdin has usbkbd added.
This fix is to change Ctrl-C polling for USB keyboard to every second
when NET transfer is running.
My previous patch is expected to be put into usb_kbd_testc(). But it went
into usb_kbd_getc() after applied.
This patch is to put change in correct place.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Jim Lin [Tue, 13 Aug 2013 11:04:22 +0000 (19:04 +0800)]
console: usb: kbd: To improve TFTP booting performance
TFTP booting is slow when a USB keyboard is installed and
stdin has usbkbd added.
This fix is to change Ctrl-C polling for USB keyboard to every second
when NET transfer is running.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Jim Lin [Tue, 13 Aug 2013 11:03:05 +0000 (19:03 +0800)]
NET: Add net_busy_flag if CONFIG_USB_KEYBOARD is defined
This flag is to make console aware that NET transfer is running or not.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Fabio Estevam [Fri, 26 Jul 2013 16:54:28 +0000 (13:54 -0300)]
usb: ehci-mx5: Use 'bool' instead of 'unsigned char'
The 'enable' argument can be better expressed as boolean.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
Fabio Estevam [Fri, 26 Jul 2013 16:54:27 +0000 (13:54 -0300)]
usb: ehci-mx5: Remove unneeded write to cscmr1 register
Currently we have the following behavior in ehci_hcd_init()
- Read csmr1 register, clear bit 26 and then set bit 26.
However a little bit later we call set_usb_phy_clk() which clears bit 26, so
let's get rid of the unnecessary code.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Lukasz Majewski [Mon, 19 Aug 2013 15:17:19 +0000 (17:17 +0200)]
usb:dfu:g_dnl: Refactoring the string definition code for g_dnl driver
The manufacturer and product IDs are dynamically assigned when gadget is
bind.
Now the IDs aren't assigned at struct g_dnl_string_defs definition.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: "Egli, Samuel" <samuel.egli@siemens.com>
Lukasz Majewski [Mon, 19 Aug 2013 15:17:18 +0000 (17:17 +0200)]
usb:dfu:g_dnl: Change number of exported configurations at composite gadget
USB composite gadget (g_dnl) supports only one configuration. Due to that
the corresponding field - bConfigurationValue has been changed.
Moreover more descriptive names were chosen for relevant fields.
Windows XP setup:
- Thesyscon USB Descriptor Dumper
- zadig_xp program for WinUSB installation (which is required by dfu-util)
- dfu-util for windows (version 0.6)
- TRATS target connected via USB hub to test Win XP machine.
Tested at: Trats - Exynos4210
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: "Egli, Samuel" <samuel.egli@siemens.com>
Heiko Schocher [Thu, 25 Jul 2013 04:43:11 +0000 (06:43 +0200)]
dfu, nand, ubi: add partubi alt settings for updating ubi partition
updating an ubi partition needs a completely erased mtd partition,
see:
http://lists.infradead.org/pipermail/linux-mtd/2011-May/035416.html
So, add partubi alt setting for the dfu_alt_info environment
variable to mark this partition as an ubi partition. In case we
update an ubi partition, we erase after flashing the image into the
partition, the remaining sektors.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@ti.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Julius Werner [Fri, 19 Jul 2013 20:12:08 +0000 (13:12 -0700)]
usb: Use well-known descriptor sizes when parsing configuration
The existing USB configuration parsing code relies on the descriptors'
own length values when reading through the configuration blob. Since the
size of those descriptors is always well-defined, we should rather use
the known sizes instead of trusting device-provided values to be
correct. Also adds some safety to potential out-of-order descriptors.
Change-Id: I16f69dfdd6793aa0fe930b5148d4521f3e5c3090
Signed-off-by: Julius Werner <jwerner@chromium.org>
Dan Murphy [Thu, 1 Aug 2013 19:06:02 +0000 (14:06 -0500)]
ARM: OMAP5-uevm: Add usb device reset API
Add the call back to reset the LAN9730 after
the FEAT_POWER has been called.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Dan Murphy [Thu, 1 Aug 2013 19:06:01 +0000 (14:06 -0500)]
USB: usb-hub: Add a weak function for resetting devices
Add a __weak function that can be overridden to reset devices
attached to an ehci devices after the FEAT_POWER has been submitted
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Dan Murphy [Thu, 1 Aug 2013 19:06:00 +0000 (14:06 -0500)]
ARM: OMAP5-uevm: Add USB MAC ethernet address
Set the usbethaddr based on the OMAP DIE_ID registers
which should be unique for each processor.
Then set this as the usb ethernet MAC address.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Dan Murphy [Thu, 1 Aug 2013 19:05:59 +0000 (14:05 -0500)]
ARM: OMAP5-uevm: Add USB ehci support for the uEVM
Add the USB ehci support for the OMAP5 uEVM.
Configure the uEVM mux data
Add the flags to build the appropriate modules
Add the usb call backs to initialize the EHCI controller
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Dan Murphy [Thu, 1 Aug 2013 19:05:58 +0000 (14:05 -0500)]
ARM: OMAP: USB: Fix linker error when ULPI is not defined
Fix the linker error for missing ulpi_reset when ulpi is not defined
in the board config.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Dan Murphy [Thu, 1 Aug 2013 19:05:57 +0000 (14:05 -0500)]
ARM: OMAP5: USB: Add OMAP5 common USB EHCI information
* Enable the OMAP5 EHCI host clocks
* Add OMAP5 EHCI register definitions
* Add OMAP5 ES2 host revision
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Dan Murphy [Thu, 1 Aug 2013 19:05:56 +0000 (14:05 -0500)]
omap5: uevm: Change the board name to correct name
Change the board name for the sys info to
5432 uEVM
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Amaury Pouly [Thu, 1 Aug 2013 14:21:00 +0000 (16:21 +0200)]
mmc: mxsmmc: Enable MMC HC support
Enable support for high-capacity eMMC and MMC cards. The MXS MMC
driver has no problem with those.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Amaury Pouly <amaury.pouly@gmail.com>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
Piotr Wilczek [Tue, 21 May 2013 13:39:04 +0000 (15:39 +0200)]
arm:exynos:gpio: fix s5p_gpio_part_max for exynos4x12
This patch fix wrong value returned by 's5p_gpio_part_max' function
for Exynos4412.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Phil Sutter [Fri, 19 Jul 2013 10:20:26 +0000 (12:20 +0200)]
env_nand.c: support falling back to redundant env when writing
Without this patch, when the currently chosen environment to be written
has bad blocks, saveenv fails completely. Instead, when there is
redundant environment fall back to the other copy. Environment reading
needs no adjustment, as the fallback logic for incomplete writes applies
to this case as well.
Signed-off-by: Phil Sutter <phil.sutter@viprinet.com>
Masahiro Yamada [Fri, 12 Jul 2013 01:53:37 +0000 (10:53 +0900)]
nand_util: delete a useless variable
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Thu, 11 Jul 2013 08:29:57 +0000 (17:29 +0900)]
cmd_nand: Do not show usage when scrub is aborted
When executing nand scrub, the user gets the prompt:
Really scrub this NAND flash? <y/N>
We do not want the annoying usage displayed when saying N here.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Thu, 11 Jul 2013 08:27:13 +0000 (17:27 +0900)]
cmd_nand: slight optimization of nand_dump function
If a non-zero value is given to only_oob argument,
printing the main area is skipped.
With a little modification, we can skip the whole
while loop.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Thu, 11 Jul 2013 08:27:12 +0000 (17:27 +0900)]
cmd_nand: fix a memory leak in nand_dump function
If datbuf = memalign(ARCH_DMA_MINALIGN, nand->writesize);
succeeds and
oobbuf = memalign(ARCH_DMA_MINALIGN, nand->oobsize);
fails, nand_dump function should free databuf.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Jens Scharsig (BuS Elektronik) [Thu, 22 Aug 2013 06:11:23 +0000 (08:11 +0200)]
arm: atmel: cpux9k2: board update and enhancement
- fix adresses in env settings in config header
- add missing CONFIG_STANDALONE_LOAD_ADDR to eb_cpux9k2 config header
- remove jffs2 support, board doesn't use this anymore
- add ubifs support
- change sizes and start for partitions
Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Tue, 13 Aug 2013 06:38:32 +0000 (14:38 +0800)]
gpio: atmel: add copyright and remove error header info
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Jens Scharsig <js_at_ng@scharsoft.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Tue, 13 Aug 2013 06:38:31 +0000 (14:38 +0800)]
gpio: atmel: add gpio common API support
add gpio common API support for gpio command
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[fix unnecessary cast]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Thu, 22 Aug 2013 07:24:40 +0000 (15:24 +0800)]
gpio: atmel: fix code to use pointer for pio port
fix code to use pointer for pio port as the warning message suggested
remove the warning message
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Tue, 13 Aug 2013 06:50:49 +0000 (14:50 +0800)]
arm: atmel: remove the config.mk file
remove the config.mk file
move text base define to board config file for following boards
- at91sam9m10g45ek
- at91sam9x5ek
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Sun, 11 Aug 2013 14:26:20 +0000 (14:26 +0000)]
arm: atmel: sama5d3: fix typo error for CONFIG_ENV_IS_NOWHERE
fix typo error for CONFIG_ENV_IS_NOWHERE from CONIG_ENV_IS_NOWHERE
Signed-off-by: Bo Shen <voice.shen@gmail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Fri, 9 Aug 2013 07:45:39 +0000 (15:45 +0800)]
arm: sama5d3: remove unused define
The CONFIG_MAX_NAND_CHIPS never used, remove it
No where define LCD_TEST_PATTERN, so no need undefine
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Fri, 9 Aug 2013 07:43:09 +0000 (15:43 +0800)]
arm: sama5d3: fix smc cs related registers offset
the smc cs related registers start at 0x600 and loop with 5 registers
so the reserved register should be in at91_smc structure while no in
at91_cs structure. So fix it
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Wu, Josh [Thu, 4 Jul 2013 07:36:23 +0000 (15:36 +0800)]
ARM: at91: atmel_nand: add code to check the ONFI parameter ECC requirement
1. if CONFIG_SYS_NAND_ONFI_DETECTION is defined, driver will check NAND flash's
ecc minimum requirement in ONFI parameter.
a) if CONFIG_PMECC_CAP, CONFIG_PMECC_SECTOR_SIZE are defined. then use it.
Driver will display a WARNING if the values are different from ONFI
parameters.
b) if CONFIG_PMECC_CAP, CONFIG_PMECC_SECTOR_SIZE are not defined, then use
the value from ONFI parameters.
* If ONFI ECC parameters are in ONFI extended parameter page, since we
are not support it, so assume the minimum ecc requirement is 2 bits
in 512 bytes.
* For non-ONFI support nand flash, also assume the minimum ecc
requirement is 2 bits in 512 bytes.
2. if CONFIG_SYS_NAND_ONFI_DETECTION is not defined, just use CONFIG_PMECC_CAP
and CONFIG_PMECC_SECTOR_SIZE.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Wu, Josh [Wed, 3 Jul 2013 03:11:48 +0000 (11:11 +0800)]
mtd: atmel_nand: alloc memory instead of use static array for pmecc data
In this way, the pmecc corraction capbility can change in run time.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Wu, Josh [Wed, 3 Jul 2013 03:11:47 +0000 (11:11 +0800)]
linux/compat.h: move dev_err, dev_info and dev_dbg from usb driver to compat.h
Since kernel code current use many dev_xxx() instead of using printk. To
compatible, move those dev_xxx from usb driver to linux/compat.h. Then all
driver code can use dev_err, dev_info and dev_vdbg.
This patch also removed duplicated macro definitions in usb driver.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Wu, Josh [Wed, 3 Jul 2013 03:11:46 +0000 (11:11 +0800)]
ARM: at91: sama5d3: remove unused definition about PMECC alpha table offset
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Wu, Josh [Wed, 3 Jul 2013 03:11:45 +0000 (11:11 +0800)]
ARM: at91: atmel_nand: pmecc driver will select the galois table by sector size
Define the galois index table offset in chip head file. So user do not need
to set by himself. Driver will set it correctly according to sector_size.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
[rebased on master]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Wed, 26 Jun 2013 02:48:53 +0000 (10:48 +0800)]
arm: atmel: add nand trimffs subcommand for at91sam9n12 and at91sam9x5
as the at91sam9n12 and at91sam9x5 soc support PMECC, when use u-boot
to flash the rootfs, in order to avoid flash one sector with all 0xff
into NAND, so use nand trimffs subcommand to avoid it
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Wed, 26 Jun 2013 02:11:06 +0000 (10:11 +0800)]
arm: atmel: add gmac support for sama5d3xek board
add gmac support for sama5d3xek board, the gmac embedded in:
- sama5d33, sama5d34, sama5d35
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Mon, 19 Aug 2013 02:35:47 +0000 (10:35 +0800)]
net: macb: fix the following building warning
fix the following building warning
---8>---
macb.c: In function 'macb_init':
macb.c:400:14: warning: 'phydev' may be used uninitialized in this function
macb.c:377:21: note: 'phydev' was declared here
---<8---
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Tom Rini [Wed, 21 Aug 2013 20:27:47 +0000 (16:27 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
Eric Nelson [Fri, 2 Aug 2013 17:37:00 +0000 (10:37 -0700)]
fec_mxc: set ethaddr if fuses burned and not previously set
Without this change, the following message is generated:
Warning: FEC using MAC address from net device
See doc/README.enetaddr for details.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Andreas Wass [Fri, 16 Aug 2013 16:24:37 +0000 (18:24 +0200)]
ARM: mxs: Add mx28evk_auart_console target
The target uses AUART 3 instead of the DUART for console output.
Signed-off-by: Andreas Wass <andreas.wass@dalelven.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Andreas Wass [Wed, 14 Aug 2013 21:45:03 +0000 (23:45 +0200)]
ARM: mxs: Added application UART driver
The driver makes it possible to use an application UART as
the U-Boot output console for Freescale i.MX23/i.MX28 devices.
Signed-off-by: Andreas Wass <andreas.wass@dalelven.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Eric Nelson [Tue, 20 Aug 2013 18:44:43 +0000 (11:44 -0700)]
i.MX6: nitrogen6x: force HDMI onto IPU0/DI0
Our Linux kernel switches the HDMI connector onto IPU0/DI1,
but the U-Boot display driver only supports IPU0/DI0 for the
time being.
Because of this, a soft re-boot will leave the HDMI output
connected to the wrong display port and prevent video from
being displayed.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
York Sun [Wed, 21 Aug 2013 16:03:29 +0000 (09:03 -0700)]
Makefile: Fix build in a separated directory tree
Fix a bug introduced by commit
3aa29dee
TPL : introduce the TPL based on the SPL
Signed-off-by: York Sun <yorksun@freescale.com>
Николай Пузанов [Wed, 19 Jun 2013 07:48:44 +0000 (11:48 +0400)]
Fix for incorrect conversion hex string to number (FMAN firmware address).
Signed-off-by: Николай Пузанов <punzik@gmail.com>
Acked-by: York Sun <yorksun@freescale.com>
Shengzhou Liu [Thu, 15 Aug 2013 01:31:47 +0000 (09:31 +0800)]
powerpc/sec: Add workaround for SEC A-003571
Multiple read/write transactions initiated by security
engine may cause system to hang.
Workaround: set MCFGR[AXIPIPE] to 0 to avoid hang.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Shengzhou Liu [Tue, 13 Aug 2013 08:41:19 +0000 (16:41 +0800)]
powerpc/p1010rdb: fix calculating ddr_freq_mhz
There was a bug for calculating ddr_freq_mhz,
it should be divided by 1000000 rather than 0x1000000.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Shaohui Xie [Mon, 19 Aug 2013 10:58:52 +0000 (18:58 +0800)]
powerpc/t4240: add QSGMII interface support
Also some fix for QSGMII.
1. fix QSGMII configure of Serdes2.
2. fix PHY address of QSGMII MAC9 & MAC10 for each FMAN.
3. fix dtb for QSGMII interface.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Shaohui Xie [Mon, 19 Aug 2013 10:57:57 +0000 (18:57 +0800)]
powerpc/t4240: fix lanes routing for QSGMII protocols
When using QSGMII protocols, the first lane and third lane on each slot
need to be swapped.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Shaohui Xie [Mon, 19 Aug 2013 10:43:07 +0000 (18:43 +0800)]
powerpc/common/vsc3316: remove const from vsc3316_config parameter define
Since the parameters need to be modified according to different Serdes
protocols at runtime, the const will block this. Also remove const from
arrays define used by vsc3316_config.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Shruti Kanetkar [Thu, 15 Aug 2013 16:25:38 +0000 (11:25 -0500)]
powerpcv2: Print hardcoded size like print_size() does
Makes the startup output more consistent
Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: York Sun <yorksun@freescale.com>
Shruti Kanetkar [Thu, 15 Aug 2013 16:25:37 +0000 (11:25 -0500)]
powerpc: Use print_size() where appropriate
Makes the startup output more consistent
Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
York Sun [Tue, 20 Aug 2013 17:15:37 +0000 (10:15 -0700)]
SPDX-License-Identifier: clean up license header
This patch cleans up license header in these files:
board/freescale/p1022ds/spl.c
drivers/mmc/fsl_esdhc_spl.c
drivers/mtd/spi/fsl_espi_spl.c
Signed-off-by: York Sun <yorksun@freescale.com>
Prabhakar Kushwaha [Fri, 16 Aug 2013 09:22:26 +0000 (14:52 +0530)]
powerpc: Fix CamelCase checkpatch warnings
85xx, 86xx PowerPC folders have code variables with CamelCase naming conventions.
because of this code checkpatch script generates "WARNING: Avoid CamelCase".
Convert variables name to normal naming convention and modify board, driver
files with updated the new structure.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Ying Zhang [Fri, 16 Aug 2013 07:16:16 +0000 (15:16 +0800)]
powerpc: p1022ds: add TPL for p1022ds nand boot
TPL is introduced in the patch "NAND: TPL : introduce the TPL
based on the SPL", here enable TPL for p1022ds nand boot.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Ying Zhang [Fri, 16 Aug 2013 07:16:15 +0000 (15:16 +0800)]
TPL : introduce the TPL based on the SPL
Due to the nand SPL on some board(e.g. P1022DS)has a size limit, it can
not be more than 4K. So, the SPL cannot initialize the DDR with the SPD
code. This patch introduces TPL to enable a loader stub that is loaded
by the code from the SPL. It initializes the DDR with the SPD or other
operations.
The TPL's size is sizeable, the maximum size is decided by the memory's
size that TPL runs. It initializes the DDR through SPD code, and copys
final uboot image to DDR. So there are three stage uboot images:
* spl_boot, * tpl_boot, * final uboot image
Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Ying Zhang [Fri, 16 Aug 2013 07:16:14 +0000 (15:16 +0800)]
powerpc : p1022ds : Enable p1022ds to start from eSPI with SPL
Enable p1022ds to start from eSPI with SPL.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Ying Zhang [Fri, 16 Aug 2013 07:16:13 +0000 (15:16 +0800)]
powerpc : spi flash : Support to start from eSPI with SPL
This patch introduces SPL to enable a loader stub that being loaded by
the code from the internal on-chip ROM. It loads the final uboot image
into DDR, then jump to it to begin execution.
The SPL's size is sizeable, the maximum size must not exceed the size of L2
SRAM. It initializes the DDR through SPD code, and copys final uboot image
to DDR. So there are two stage uboot images:
* spl_boot, 96KB size. The env variables are copied to L2 SRAM, so that
ddr spd code can get the interleaving mode setting in env. It loads
final uboot image from offset 96KB.
* final uboot image, size is variable depends on the functions enabled.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Ying Zhang [Fri, 16 Aug 2013 07:16:12 +0000 (15:16 +0800)]
powerpc: p1022ds: Enable P1022DS to boot from SD Card with SPL
Enable p1022ds to start from eSDHC with SPL.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Ying Zhang [Fri, 16 Aug 2013 07:16:11 +0000 (15:16 +0800)]
powerpc: mpc85xx: Support booting from SD Card with SPL
The code from the internal on-chip ROM. It loads the final uboot image
into DDR, then jump to it to begin execution.
The SPL's size is sizeable, the maximum size must not exceed the size of L2
SRAM. It initializes the DDR through SPD code, and copys final uboot image
to DDR. So there are two stage uboot images:
* spl_boot, 96KB size. The env variables are copied to L2 SRAM, so that
ddr spd code can get the interleaving mode setting in env. It loads
final uboot image from offset 96KB.
* final uboot image, size is variable depends on the functions enabled.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Ying Zhang [Fri, 16 Aug 2013 07:16:10 +0000 (15:16 +0800)]
powerpc: deleted unused symbol CONFIG_SPL_NAND_MINIMAL and enabled some functionality for common SPL
1. The symbol CONFIG_SPL_NAND_MINIMAL is unused, so deleted it.
2. Some functions were unused in the minimal SPL, but it is useful
in the common SPL. So, enabled some functionality for common SPL.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Ying Zhang [Thu, 20 Jun 2013 08:04:24 +0000 (16:04 +0800)]
spl: env_common.c: make CONFIG_SPL_BUILD contain function env_import
The functionality env_import will be used in the SPL. They
had been excluded by ifndef CONFIG_SPL_BUILD. Now, put it
into the SPL.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: York Sun <yorksun@freescale.com>
Matthias Fuchs [Wed, 7 Aug 2013 10:10:38 +0000 (12:10 +0200)]
ppc4xx: Remove support for PPC405CR CPUs
This patch removes support for the APM 405CR CPU.
This CPU is EOL and no board uses this chip.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Matthias Fuchs [Wed, 7 Aug 2013 11:22:10 +0000 (13:22 +0200)]
ppc4xx: Remove CANBT board
This board and especially the CPU (PPC405CR) is EOL.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Acked-by: Wolfgang Denk <wd@denx.de>
Tom Rini [Tue, 20 Aug 2013 15:34:24 +0000 (11:34 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-i2c
Łukasz Majewski [Fri, 16 Aug 2013 13:35:26 +0000 (15:35 +0200)]
pmic:i2c: Replace legacy I2C_SET_BUS macro with i2c_set_bus_num()
After introduction of unified i2c model, the I2C_SET_BUS() macro is regarded
as obsolete.
Hence it is replaced with i2c_set_bus_num() function call.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Łukasz Majewski [Fri, 16 Aug 2013 13:33:33 +0000 (15:33 +0200)]
i2c:samsung: Adjust Trats, GONI and Universal_c210 boards to work with new I2C framework
New I2C framework, introduced after v2013.07 final release, imposed I2C
code adjustment for some Samsung boards - namely Trats, GONI and Universal_c210.
Those boards were using schematic based I2C enumeration (I2C_5, I2C_9).
However, new I2C framework imposes usage of logical I2C adapters numbering
(e.g. I2C_0, I2C_1, etc).
Additionally, I2C_GET_* macros were replaced with i2c_*_bus_num() functions.
Trats board gained definition of second soft I2C adapter.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
Łukasz Majewski [Fri, 16 Aug 2013 13:31:45 +0000 (15:31 +0200)]
i2c:multibus:fix: Correct I2C_MULTI_BUS value when support for many buses is enabled
The I2C_MULTI_BUS needs to be defined for correct I2C operation with
many software emulated I2C controllers.
This fix restores correct value of the I2C_MULTI_BUS changed by following
commit:
SHA1:
385c9ef5a7215b2b0c22836fee6c692dfc8559d7
i2c: add i2c_core and prepare for new multibus support
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
Chunhe Lan [Fri, 16 Aug 2013 07:10:37 +0000 (15:10 +0800)]
fsl_i2c: add workaround for the erratum I2C A004447
This workaround is for the erratum I2C A004447. Device reference
manual provides a scheme that allows the I2C master controller
to generate nine SCL pulses, which enable an I2C slave device
that held SDA low to release SDA. However, due to this erratum,
this scheme no longer works. In addition, when I2C is used as
a source of the PBL, the state machine is not able to recover.
At the same time, delete the reduplicative definition of SVR_VER
and SVR_REV. The SVR_REV is the low 8 bits rather than the low 16
bits of svr. And we use the CONFIG_SYS_FSL_A004447_SVR_REV macro
instead of hard-code value 0x10, 0x11 and 0x20.
The CONFIG_SYS_FSL_A004447_SVR_REV = 0x00 represents that one
version of platform has this I2C errata. So enable this errata
by IS_SVR_REV(svr, maj, min) function.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
Chunhe Lan [Fri, 16 Aug 2013 07:10:36 +0000 (15:10 +0800)]
fsl_i2c: generate nine pulses on SCL if the I2C bus is hung
When the code detected that the bus is hung (e.g. SDA stuck low),
send 9 pulses on SCL to try to fixup the bus.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
Stephen Warren [Wed, 14 Aug 2013 16:05:33 +0000 (10:05 -0600)]
ARM: tegra: support raw ramdisks
This way, we don't have to run mkimage on them.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Thierry Reding [Thu, 18 Jul 2013 19:13:41 +0000 (12:13 -0700)]
ARM: tegra: Enable data cache on Dalmore
Disabling the data cache is no longer required to boot Dalmore, so
enable it. This results in notably better performance when loading
and booting the Linux kernel.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Thierry Reding [Thu, 18 Jul 2013 19:13:40 +0000 (12:13 -0700)]
ARM: tegra: Make cache line size SoC specific
Currently all Tegra SoCs are assumed to have 32 byte cache lines. This
isn't true for Tegra114, however, which uses 4 Cortex-A15 cores and
therefore uses a cache line size of 64 bytes. Move the cache line size
setting to the per-SoC common configuration file.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Joel Fernandes [Mon, 19 Aug 2013 08:14:14 +0000 (16:14 +0800)]
SPL: Makefile: Build a separate autoconf.mk for SPL
SPL defines CONFIG_SPL_BUILD but this does not percolate to the
autoconf.mk Makefile. As a result the build breaks when
CONFIG_SPL_BUILD is used in the board-specific include header file. With
this, there is a possibility of having a CONFIG option defined in the
header file but not defined in the Makefile causing all kinds of build
failure and problems.
It also messes things for up, for example, when one might want to
undefine options to keep the SPL small and doesn't want to be stuck with
the CONFIG options used for U-boot. Lastly, this also avoids defining
special CONFIG_SPL_ variables for cases where some options are required
in U-boot but not in SPL.
We add a spl-autoconf.mk rule that is generated for SPL with the
CONFIG_SPL_BUILD flag and conditionally include it for SPL builds.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Ying Zhang <b40530@freescale.com>
Tom Rini [Mon, 19 Aug 2013 21:26:15 +0000 (17:26 -0400)]
Prepare v2013.10-rc1
Signed-off-by: Tom Rini <trini@ti.com>
Wolfgang Denk [Sun, 28 Jul 2013 20:12:47 +0000 (22:12 +0200)]
SPDX-License-Identifier: convert BSD-3-Clause files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini Don't remove some copyrights by accident]
Signed-off-by: Tom Rini <trini@ti.com>
Wolfgang Denk [Sun, 28 Jul 2013 20:12:46 +0000 (22:12 +0200)]
board/esd/cpci750/mv_eth.c: Fix license
The file header indicated that this file was GPL-2.0+, but actually
the code was derived from (Marvell based) Linux source code which is
only GPL-2.0. Fix this.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Acked-by: Stefan Roese <sr@denx.de>