Timur Tabi [Fri, 4 Sep 2009 21:28:35 +0000 (16:28 -0500)]
fsl_i2c: increase I2C timeout values and make them configurable
The value of I2C_TIMEOUT in fsl_i2c.c has several problems. First, it is
defined as CONFIG_HZ/4, but it is used as a count of microseconds, so it makes
no sense to derive it from a clock rate. Second, the current value (250) is
too low for some boards, so it needs to be increased. Third, the timeout
necessary for multiple-master arbitration is larger than the timeout for basic
read/write operations, so we shouldn't have a single constant for both timeouts.
Finally, it would be nice if we could override these values on a per-board
basis.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Tested-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Peter Tyser <ptyser@xes-inc.com>
Eric Millbrandt [Thu, 3 Sep 2009 13:09:44 +0000 (08:09 -0500)]
Reset i2c slave devices during init on mpc5xxx cpus
Reset any i2c devices that may have been interrupted during a system reset.
Normally this would be accomplished by clocking the line until SCL and SDA
are released and then sending a start condtiion (From an Atmel datasheet).
There is no direct access to the i2c pins so instead create start commands
through the i2c interface. Send a start command then delay for the SDA Hold
time, repeat this by disabling/enabling the bus a total of 9 times.
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Wolfgang Denk [Fri, 4 Sep 2009 21:20:29 +0000 (23:20 +0200)]
ARM: Update mach-types
Signed-off-by: Wolfgang Denk <wd@denx.de>
Mike Frysinger [Fri, 4 Sep 2009 03:12:47 +0000 (23:12 -0400)]
push LOAD_ADDR out to arch mk files
Rather than maintain/extend the current ifeq($(ARCH)) mess that exists in
the standalone Makefile, push the setting up of LOAD_ADDR out to the arch
config.mk (and rename to STANDALONE_LOAD_ADDR in the process). This keeps
the common code clean and lets the arch do whatever crazy crap it wants in
its own area.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Giuseppe CONDORELLI [Thu, 3 Sep 2009 11:37:46 +0000 (07:37 -0400)]
zlib: fix code when DEBUG is defined
Removed stdio.h inclusion and moved trace macros to use printf avoiding to
write debug informations to standard error.
Signed-off-by: Giuseppe Condorelli <giuseppe.condorelli@st.com>
Scott Wood [Wed, 2 Sep 2009 21:45:31 +0000 (16:45 -0500)]
mxc_nand: Remove Freescale's "All Rights Reserved."
Signed-off-by: Scott Wood <scottwood@freescale.com>
Anton Vorontsov [Wed, 2 Sep 2009 13:58:48 +0000 (17:58 +0400)]
mpc83xx/serdes: License cleanup: remove "All Rights Reserved" notice
"All Rights Reserved" conflicts with the GPL.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Wolfgang Denk [Wed, 2 Sep 2009 12:57:27 +0000 (14:57 +0200)]
License cleanup: remove unintended "All Rights Reserved" notices.
Some files included my old standerd file header which had a "All
Rights Reserved" part. As this has never been my intention, I remove
these lines to make the files compatible with GPL v.2 and later.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Wed, 2 Sep 2009 08:21:20 +0000 (10:21 +0200)]
cmd_mtdparts.c: fix compiler warning in debug code
Fix warning messages:
cmd_mtdparts.c:1429: warning: format '%08lx' expects type 'long
unsigned int', but argument 6 has type 'u32'
cmd_mtdparts.c:1429: warning: format '%08lx' expects type 'long
unsigned int', but argument 7 has type 'u32'
Signed-off-by: Wolfgang Denk <wd@denx.de>
Anton Vorontsov [Tue, 1 Sep 2009 16:58:03 +0000 (20:58 +0400)]
Move uninitialized_var() macro from ubi_uboot.h to compiler.h
This is needed so that we could use this macro for non-UBI code.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Kumar Gala [Tue, 1 Sep 2009 16:24:45 +0000 (11:24 -0500)]
arm: Remove -fno-strict-aliasing
-fno-strict-aliasing is hidding warnings.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Tue, 1 Sep 2009 16:24:44 +0000 (11:24 -0500)]
ppc: Remove -fno-strict-aliasing
-fno-strict-aliasing is hidding warnings.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Eric Millbrandt [Fri, 28 Aug 2009 12:14:04 +0000 (07:14 -0500)]
galaxy5200: Add chip select region for an Epson S1D15313
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Kumar Gala [Thu, 27 Aug 2009 13:23:55 +0000 (08:23 -0500)]
Add ability for arch code to make changes before we boot
Added a arch_preboot_os() function that cpu specific code can implement to
allow for various modifications to the state of the machine right before
we boot. This can be useful to setup register state to a specific
configuration.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Roy Zang [Fri, 21 Aug 2009 19:49:52 +0000 (03:49 +0800)]
Use different PBA value for E1000 PCI and PCIe cards
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: André Schwarz <andre.schwarz@matrix-vision.de>
Graeme Russ [Sun, 23 Aug 2009 02:59:58 +0000 (12:59 +1000)]
Add PCI support to eNET board
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Graeme Russ [Sun, 23 Aug 2009 02:59:57 +0000 (12:59 +1000)]
i386: Moved PCI from #ifdef to conditional compile for sc520 boards
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Graeme Russ [Sun, 23 Aug 2009 02:59:56 +0000 (12:59 +1000)]
i386: Replace [read, write]_mmcr_[byte, word, long] with memory mapped structure
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Graeme Russ [Sun, 23 Aug 2009 02:59:55 +0000 (12:59 +1000)]
Misc sc520 cdp fixups
Now that the PCI, SATA et al compile problems have been resolved, the
cludge that was applied to avoid them can be removed
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Graeme Russ [Sun, 23 Aug 2009 02:59:54 +0000 (12:59 +1000)]
Fixup sc520_spunk board
Primary intent is to resolve build errors for this board which has been
neglected for a very long time. I do not have one of these boards, so I
cannot test functionality
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Graeme Russ [Sun, 23 Aug 2009 02:59:53 +0000 (12:59 +1000)]
Misc ds1722 fixups
This patch is based on a patch submitted by Jean-Christophe PLAGNIOL-VILLARD
on 18th May 2008 as part of a general i386 / sc520 fixup which was never
applied
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Graeme Russ [Sun, 23 Aug 2009 02:59:52 +0000 (12:59 +1000)]
Misc ti_pci1410a fixups
Removed do_pinit() - now declared in cmd_pcmcia.c
Added #define CONFIG_CMD_PCMCIA around pcmcia_off() in line with other
PCMCIA drivers
signed/unsigned type fixups
Added semi-colon after default: label as required by newer gcc
The only board that appears to use this driver is the sc520_spunk which
is very old and very likely very broken anyway. I do not have one to test
whether this patch breaks anything functionaly, I have can only check
that it compiles without warning or error
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Graeme Russ [Sun, 23 Aug 2009 02:59:51 +0000 (12:59 +1000)]
Misc SATA fixups
Cast first parameter to sata_cpy()
In /drivers/block/ata_piix.h, ata_id_has_lba48(), ata_id_has_lba(),
ata_id_has_dma(), ata_id_u32(), ata_id_u64() are all defined in
include/libata.h which is included in ata.h which is included by all files
which include ata_piix.h (only ata_piix.c) so these definitions are
supurflous to (and conlict with) this in libata.h. Interestingly, my
compiler complains about ata_id_u64 already being defined, but not
ata_id_u32
ata_dump_id() is defined in include/libata.h and should not be static
(maybe should even use ata_dump_id() in libata.c
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Graeme Russ [Sun, 23 Aug 2009 02:59:50 +0000 (12:59 +1000)]
i386: Misc PCI fixups
Change PCI_REGION_MEMORY to PCI_REGION_SYS_MEMORY (Originally done in
commit
ff4e66e93c1a, regressed by commit
6d7f610b09f8)
Cast PCI_ROM_ADDRESS_MASK to u32
Wrap probe_pci_video() call inside #ifdef CONFIG_VIDEO
Change call to pci_find_class() to pci_find_devices(). This is based on a
patch submitted on 1st March 2007 (Patch that fixes the compilation errors
for sc520_cdp board) by mushtaq_k
This patch requires that PCI_VIDEO_VENDOR_ID and PCI_VIDEO_DEVICE_ID be
specified in the board config file. Dummy values have been added for the
SC520 CDP board to enable compilation, but since I do not have one of these,
I do know what the values should be
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Graeme Russ [Sun, 23 Aug 2009 02:59:49 +0000 (12:59 +1000)]
Fix sc520 timer interrupt generation
The current implementation has the timer being started before the interrupt
handler is installed. It the interrupt occurs before the handler is
installed, the timer interrupt is never reset and the timer stops
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Graeme Russ [Sun, 23 Aug 2009 02:59:48 +0000 (12:59 +1000)]
Fix environment configuration for eNET board
The current configuration of the Environment has the redundant copy of the
environment in the Boot Flash - This was never the intent. The Environment
should instead be in the first two sectors of the first Strata Flash
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Graeme Russ [Sun, 23 Aug 2009 02:59:47 +0000 (12:59 +1000)]
i386: Fix regression introduced by commit
8c63d47651f7
A local variable was deleted that should not have been
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Graeme Russ [Sun, 23 Aug 2009 02:59:46 +0000 (12:59 +1000)]
i386: Change inline asm global symbols to local
gcc 4.3.2 optimiser creates multiple copies of inline asm (who knows why)
Remove use of global names for labels to prevent 'symbol already defined'
errors
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Graeme Russ [Sun, 23 Aug 2009 02:59:45 +0000 (12:59 +1000)]
i386: Add errno.h
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Peter Tyser [Sat, 22 Aug 2009 04:05:21 +0000 (23:05 -0500)]
Consolidate arch-specific mem_malloc_init() implementations
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Sat, 22 Aug 2009 04:05:20 +0000 (23:05 -0500)]
Standardize mem_malloc_init() implementation
This lays the groundwork to allow architectures to share a common
mem_malloc_init().
Note that the x86 implementation was not modified as it did not fit the
mold of all other architectures.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Sat, 22 Aug 2009 04:05:19 +0000 (23:05 -0500)]
Consolidate arch-specific sbrk() implementations
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Mike Frysinger [Thu, 23 Jul 2009 20:37:03 +0000 (16:37 -0400)]
atmel_df_pow2: standalone to convert dataflashes to pow2
Atmel DataFlashes by default operate with pages that are slightly bigger
than normal binary sizes (i.e. many are 1056 byte pages rather than 1024
bytes). However, they also have a "power of 2" mode where the pages show
up with the normal binary size. The latter mode is required in order to
boot with a Blackfin processor, so many people wish to convert their
DataFlashes on their development systems to this mode. This standalone
application does just that.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Wed, 2 Sep 2009 09:52:37 +0000 (05:52 -0400)]
Blackfin: cm-bf548: fix device->stdio_dev fallout
The recent
52cb4d4fb348 commit which renamed device to stdio_dev missed the
cm-bf548's video board.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Wed, 2 Sep 2009 08:21:16 +0000 (04:21 -0400)]
Blackfin: enable 64bit printf for nand
Since the NAND code now uses 64bit code, make sure we enable support for
ADI Blackfin boards in printf to avoid the warning:
nand_util.c:45:2: warning: #warning Please define CONFIG_SYS_64BIT_VSPRINTF for correct output!
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Tue, 25 Aug 2009 00:48:04 +0000 (20:48 -0400)]
Blackfin: use scratch pad for exception stack
If the memory layout pushes the stack out of the default DCPLB coverage,
the exception handler may trigger a double fault by trying to push onto
the uncovered stack. So handle the exception stack similar to the kernel
by using the top of the scratch pad SRAM.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Tue, 25 Aug 2009 00:36:25 +0000 (20:36 -0400)]
Blackfin: increase default console size
The default console size indirectly applies to length of env vars, so a
smaller length makes it hard to pass longer command lines to kernels.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Mon, 24 Aug 2009 23:03:18 +0000 (19:03 -0400)]
Blackfin: fix debug printf modifiers
The display_global_data() function generated warnings with pretty much
every variable.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Harald Krapfenbauer [Thu, 20 Aug 2009 23:20:41 +0000 (19:20 -0400)]
Blackfin: cm-bf537u: new board port
The CM-BF537U is similar to the CM-BF537E module, but enough to need its
own board port.
Signed-off-by: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Robin Getz [Mon, 17 Aug 2009 15:23:02 +0000 (15:23 +0000)]
Blackfin: change global data register from P5 to P3
Since the Blackfin ABI favors higher scratch registers by default, use the
last scratch register (P3) for global data rather than the first (P5).
This allows the compiler's register allocator to use higher number scratch
P registers, which in turn better matches the Blackfin instruction set,
which reduces the size of U-Boot by more than 1024 bytes...
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Robin Getz [Tue, 11 Aug 2009 14:20:13 +0000 (14:20 +0000)]
Blackfin: enable more network commands for ADI dev boards
Add dns and ntp to default networking commands, and ask for more dhcp
options to better configure the network environment.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Michael Hennerich [Thu, 18 Jun 2009 09:12:50 +0000 (09:12 +0000)]
Blackfin: bf537-stamp: comment CF-Flash Card Support better
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Robin Getz [Fri, 10 Jul 2009 18:37:15 +0000 (18:37 +0000)]
Blackfin: use +(filesize) to make sure we are only doing what is necessary
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Wolfgang Denk [Mon, 31 Aug 2009 20:21:47 +0000 (22:21 +0200)]
Merge branch 'next' of ../next
Wolfgang Denk [Mon, 31 Aug 2009 17:57:42 +0000 (19:57 +0200)]
Prepare 2009.08
Update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
Andre Schwarz [Mon, 31 Aug 2009 14:18:24 +0000 (16:18 +0200)]
Add common code dir for Matrix Vision boards.
This fixes current build failure.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
mvblm7.c: fix warning: implicit declaration of function
'mv_reset_environment'
Signed-off-by: Wolfgang Denk <wd@denx.de>
David Brownell [Sun, 30 Aug 2009 18:05:29 +0000 (11:05 -0700)]
bugfix CONFIG_SYS_CONSOLE_INFO_QUIET
The "console: unify printing current devices" patch goofed:
CONFIG_SYS_CONSOLE_INFO_QUIET is supposed to *REMOVE* boot
time noise, not add it. Said patch changed the #ifndefs
to #ifdef; this one restores them to the proper sense.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Timur Tabi [Fri, 28 Aug 2009 21:56:45 +0000 (16:56 -0500)]
fsl: simplify the "mac id" command, improve boot-time informational message
The "mac id" command took a 4-character parameter as the identifier string.
However, for any given board, only one kind of identifier is acceptable, so it
makes no sense to ask the user to type it in. Instead, if the user enters
"mac id", the identifier (and also the version, if it's NXID) will
automatically be set to the correct value.
Improve the message that is displayed when EEPROM is read during boot. It now
displays "EEPROM:" and then either an error message or the EEPROM identifier
if successful.
If the identifier in EEPROM is valid, then always reject a bad CRC, even if the
CRC field has not been initialized.
Don't force the MAC address count to MAX_NUM_PORTS or less. Forcing the value
to be changed resulting in an in-memory copy that does not match what's in
hardware, even though the user did not request that change.
Finally, always update the CRC value in the in-memory copy after any field
is changed, so that the CRC is always correct.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Poonam Aggrwal [Fri, 21 Aug 2009 01:59:58 +0000 (07:29 +0530)]
85xx: Added PCIe support for P1 P2 RDB
Call fsl_pci_init_port() to initialize all the PCIe ports on the board.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Poonam Aggrwal [Fri, 21 Aug 2009 01:59:42 +0000 (07:29 +0530)]
driver/fsl_pci: Add fsl_pci_init_port function to initialize a PCI controller
fsl_pci_init_port can be called from board specific PCI initialization
routines to setup the PCI (or PCIe) controller. This will reduce code
redundancy in most of the 85xx/86xx FSL board ports that setup PCI.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Timur Tabi [Thu, 20 Aug 2009 22:41:11 +0000 (17:41 -0500)]
85xx: Improve MPIC initialization
The MPIC initialization code for Freescale e500 CPUs was not using I/O
accessors, and it was not issuing a read-back to the MPIC after setting
mixed mode. This may be the cause of a spurious interrupt on some systems.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Poonam Aggrwal [Thu, 20 Aug 2009 13:29:18 +0000 (18:59 +0530)]
85xx: Added support for P1011RDB and P2010RDB
P1011 and P2010 are single core variants of P1010 and P2020 respectively.
The board(RDB) will be same.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Poonam Aggrwal [Thu, 20 Aug 2009 13:27:45 +0000 (18:57 +0530)]
85xx: Added single core members of FSL P1xx/P2xx processors series
P1011 - Single core variant of P1020
P2010 - Single core variant of P2020
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Poonam Aggrwal [Thu, 20 Aug 2009 13:27:02 +0000 (18:57 +0530)]
85xx: P1020RDB Support Added
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Poonam Aggrwal [Thu, 20 Aug 2009 13:25:35 +0000 (18:55 +0530)]
85xx: Added CONFIG_MAX_CPUS for P1020
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Mingkai Hu [Tue, 18 Aug 2009 07:37:15 +0000 (15:37 +0800)]
85xx: Add L2SRAM Register's macro definition
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Felix Radensky [Sat, 15 Aug 2009 12:08:37 +0000 (15:08 +0300)]
85xx: Fix memory test range on MPC8536DS
With current values of CONFIG_SYS_MEMTEST_START and CONFIG_SYS_MEMTEST_END
memory test hangs if run without arguments. Set them to sane values, so
that all available 512MB of RAM excluding exception vectors at the bottom
and u-boot code and stack at the top can be tested.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 12 Aug 2009 05:10:44 +0000 (00:10 -0500)]
85xx: Removed BEDBUG support on P1_P2_RDB
To match all other 85xx platforms we are removing BEDBUG support.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Sat, 8 Aug 2009 15:42:30 +0000 (10:42 -0500)]
85xx: Init pci ethernet cards if we enable any on MPC8572DS
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Peter Tyser [Fri, 7 Aug 2009 18:16:34 +0000 (13:16 -0500)]
xes: Use proper IO access functions
Also fix some minor whitespace oddities while we're cleaning up
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Fri, 7 Aug 2009 18:00:55 +0000 (13:00 -0500)]
85xx: Move to a common linker script
There are really no differences between all the 85xx linker scripts so
we can just move to a single common one. Board code is still able to
override the common one if need be.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Poonam Aggrwal [Fri, 31 Jul 2009 06:38:27 +0000 (12:08 +0530)]
85xx: Added P1020 Processor Support.
P1020 is another member of QorIQ series of processors which falls in ULE
category. It is an e500 based dual core SOC.
Being a scaled down version of P2020 it has following differences:
- 533MHz - 800MHz core frequency.
- 256Kbyte L2 cache
- Ethernet controllers with classification capabilities.
Also the SOC is pin compatible with P2020
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Poonam Aggrwal [Wed, 5 Aug 2009 07:59:24 +0000 (13:29 +0530)]
85xx: Add support for P2020RDB board
The code base adds P1 & P2 RDB platforms support.
The folder and file names can cater to future SOCs of P1/P2 family.
P1 & P2 processors are 85xx platforms, part of Freescale QorIQ series.
Tested following on P2020RDB:
1. eTSECs
2. DDR, NAND, NOR, I2C.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Poonam Aggrwal [Fri, 31 Jul 2009 06:38:14 +0000 (12:08 +0530)]
8xxx: Removed CONFIG_NUM_CPUS from 85xx/86xx
The number of CPUs are getting detected dynamically by checking the
processor SVR value. Also removed CONFIG_NUM_CPUS references from all
the platforms with 85xx/86xx processors.
This can help to use the same u-boot image across the platforms.
Also revamped and corrected few Freescale Copyright messages.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Poonam Aggrwal [Fri, 31 Jul 2009 06:37:45 +0000 (12:07 +0530)]
8xxx: Refactored common cpu specific code for 85xx/86xx into one file.
Removed same code pieces from cpu/mpc85xx/cpu.c and cpu/mpc86xx/cpu.c
and moved to cpu/mpc8xxx/cpu.c(new file)
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Alex Dubov [Fri, 7 Aug 2009 05:28:32 +0000 (15:28 +1000)]
stx: create common vendor/board hierarchy for STx boards
Move files belonging to the STx boards into common vendor directory and
update the Makefile to reflect this.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Peter Tyser [Tue, 4 Aug 2009 22:38:00 +0000 (17:38 -0500)]
85xx: Remove unused CONFIG_CLEAR_LAW0 defines
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 6 Aug 2009 23:38:43 +0000 (18:38 -0500)]
86xx: Remove redudant PLATFORM_CPPFLAGS
For historic reasons we had defined some additional PLATFORM_CPPFLAGS like:
PLATFORM_CPPFLAGS += -DCONFIG_MPC86xx=1
PLATFORM_CPPFLAGS += -DCONFIG_MPC8641=1
However these are all captured in the config.h and thus redudant. Also
moved common 86xx flags into cpu/mpc86xx/config.mk.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 6 Aug 2009 23:28:34 +0000 (18:28 -0500)]
85xx: Remove redudant PLATFORM_CPPFLAGS
For historic reasons we had defined some additional PLATFORM_CPPFLAGS
like:
PLATFORM_CPPFLAGS += -DCONFIG_E500=1
PLATFORM_CPPFLAGS += -DCONFIG_MPC85xx=1
PLATFORM_CPPFLAGS += -DCONFIG_MPC8548=1
However these are all captured in the config.h and thus redudant.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 30 Jul 2009 20:54:07 +0000 (15:54 -0500)]
85xx: Add a 36-bit physical configuration for MPC8536DS
We move all IO addressed (CCSR, localbus, PCI) above the 4G boundary
to allow for larger memory sizes.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Tue, 4 Aug 2009 14:10:03 +0000 (09:10 -0500)]
85xx: Cleanup whitespace in mpc8536ds.c
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 5 Aug 2009 12:59:35 +0000 (07:59 -0500)]
pci/fsl_pci_init: Rework PCI ATMU setup to handle >4G of memory
The old PCI ATMU setup code would just mimic the PCI regions into the
ATMU registers. For simple memory maps in which all memory, MMIO, etc
space fit into 4G this works ok. However there are issues with we have
>4G of memory as we know can't access all of memory and we need to
ensure that PCICSRBAR (PEXCSRBAR on PCIe) isn't overlapping with
anything since we can't turn it off.
We first setup outbound windows based on what the board code setup
in the pci regions for MMIO and IO access. Next we place PCICSRBAR
below the MMIO window. After which we try to setup the inbound windows
to map as much of memory as possible.
On PCIe based controllers we are able to overmap the ATMU setup since
RX & TX links are separate but report the proper amount of inbound
address space to the region tracking to ensure there is no overlap.
On PCI based controllers we use as many inbound windows as available to
map as much of the memory as possible.
Additionally we changed all the CCSR register access to use proper IO
accessor functions. Also had to add CONFIG_SYS_CCSRBAR_PHYS to some
86xx platforms that didn't have it defined.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 5 Aug 2009 12:49:27 +0000 (07:49 -0500)]
pci/fsl_pci_init: Use PCIe capability to determine if controller is PCIe
Change the code to use the PCIe capabilities register to determine if we
are a PCIe controller or not. Additionally cleaned up some white space
and formatting in the file.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Tue, 4 Aug 2009 02:02:02 +0000 (21:02 -0500)]
pci/fsl_pci_init: Fold fsl_pci_setup_inbound_windows into fsl_pci_init
Every platform that calls fsl_pci_init calls fsl_pci_setup_inbound_windows
before it calls fsl_pci_init. There isn't any reason to just call it
from fsl_pci_init and simplify things a bit.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Tue, 4 Aug 2009 01:44:55 +0000 (20:44 -0500)]
pci/fsl_pci_init: Fold pci_setup_indirect into fsl_pci_init
Every platform that calls fsl_pci_init calls pci_setup_indirect before
it calls fsl_pci_init. There isn't any reason to just call it from
fsl_pci_init and simplify things a bit.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
André Schwarz [Thu, 27 Aug 2009 12:48:35 +0000 (14:48 +0200)]
Use common code for Matrix Vision boards
Clean up existing boards (mvBC-P/MPC5200 and mvBL-M7/MPC8343) by
using common code.
Signed-off-by: André Schwarz <andre.schwarz@matrix-vision.de>
Wolfgang Denk [Thu, 27 Aug 2009 22:17:41 +0000 (00:17 +0200)]
Merge branch 'next' of git://git.denx.de/u-boot-nand-flash into next
Kim Phillips [Thu, 27 Aug 2009 02:27:37 +0000 (21:27 -0500)]
mpc83xx: mpc8349itx - accommodate larger kernel sizes & unzero the bootdelay
apparently the ITX was missed last round.
Also make bootdelay consistent with other boards, so as to give on the
opportunity to fix mistakenly set bootcmd without having checked for an
bootdelay zero setting first.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Kim Phillips [Thu, 27 Aug 2009 02:25:46 +0000 (21:25 -0500)]
mpc83xx: match dtb filename references to their dts equivalents in the linux kernel
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Sandeep Paulraj [Tue, 18 Aug 2009 14:10:42 +0000 (10:10 -0400)]
NAND: DaVinci: V2 Adding 4 BIT ECC support
This patch adds 4 BIT ECC support in the DaVinci NAND
driver. Tested on both the DM355 and DM365.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Sandeep Paulraj [Mon, 10 Aug 2009 17:27:56 +0000 (13:27 -0400)]
MTD:NAND: ADD new ECC mode NAND_ECC_HW_OOB_FIRST
This patch adds the new mode NAND_ECC_HW_OOB_FIRST in the nand code to
support 4-bit ECC on TI DaVinci devices with large page (up to 2K) NAND
chips. This ECC mode is similar to NAND_ECC_HW, with the exception of
read_page API that first reads the OOB area, reads the data in chunks,
feeds the ECC from OOB area to the ECC hw engine and perform any
correction on the data as per the ECC status reported by the engine.
This patch has been accepted by Andrew Morton and can be found at
http://userweb.kernel.org/~akpm/mmotm/broken-out/mtd-nand-add-new-ecc-mode-ecc_hw_oob_first.patch
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Ilya Yanok [Mon, 10 Aug 2009 22:32:54 +0000 (02:32 +0400)]
mxc_nand: add nand driver for MX2/MX3
Driver for NFC NAND controller found on Freescale's MX2 and MX3
processors. Ported from Linux. Tested only with i.MX27 but should
works with other MX2 and MX3 processors too.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Sandeep Paulraj [Mon, 10 Aug 2009 17:27:46 +0000 (13:27 -0400)]
NAND: ADD page Parameter to all read_page/read_page_raw API's
This patch adds a new "page" parameter to all NAND read_page/read_page_raw
APIs. The read_page API for the new mode ECC_HW_OOB_FIRST requires the
page information to send the READOOB command and read the OOB area before
the data area.
This patch has been accepted by Andrew Morton and can be found at
http://userweb.kernel.org/~akpm/mmotm/broken-out/mtd-nand-add-page-parameter-to-all-read_page-read_page_raw-apis.patch
WE would like this to become part of the u-boot GIT as well
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Heiko Schocher [Tue, 21 Jul 2009 15:13:40 +0000 (17:13 +0200)]
83xx, kmeter1: added NAND support
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Kyungmin Park [Tue, 21 Jul 2009 02:58:04 +0000 (11:58 +0900)]
OneNAND: Remove unused read_spareram
Remove unused read_spareram and add unlock_all as kernel does
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Matthias Kaehlcke [Thu, 16 Jul 2009 19:19:29 +0000 (21:19 +0200)]
KB9202: Add NAND support
Add KB9202 NAND driver
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Kyungmin Park [Tue, 21 Jul 2009 02:58:04 +0000 (11:58 +0900)]
OneNAND: Remove unused read_spareram
Remove unused read_spareram and add unlock_all as kernel does
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Eric Millbrandt [Tue, 25 Aug 2009 15:30:26 +0000 (10:30 -0500)]
galaxy5200: Cleanup typo and trailing whitespace
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Wolfgang Denk [Wed, 26 Aug 2009 19:29:32 +0000 (21:29 +0200)]
Merge branch 'next' of git://denx.de/git/u-boot-coldfire into next
TsiChung Liew [Wed, 22 Jul 2009 18:42:45 +0000 (18:42 +0000)]
ColdFire: Fix compile warning messages
Change %08lX to %08X in board.c. Remove unused variable
'oscillator' in mcf5227x/cpu_init.c and 'scm2' in
mcf532x/cpu_init.c. Provide argument type cast in
drivers/dma/MCD_dmaApi.c.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
TsiChung Liew [Wed, 22 Jul 2009 16:32:39 +0000 (16:32 +0000)]
ColdFire: Fix missing _IO_BASE which caused compile error
The compile error was caused by a recent patch. Affected platforms -
M5253DEMO.h, M5253EVBE.h, and M54455EVB.h. Adding the _IO_BASE
automatically defined to 0 in asm-m68k/io.h if it isn't set in
platform configuration file.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Niklaus Giger [Wed, 22 Jul 2009 15:13:24 +0000 (17:13 +0200)]
Support up to 7 banks for ids as specified in JEDEC JEP106Z
see http://www.jedec.org/download/search/jep106Z.pdf
Add some second source legacy flash chips 256x8.
Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Wolfgang Denk [Tue, 25 Aug 2009 21:03:22 +0000 (23:03 +0200)]
Merge branch 'next' of git://git.denx.de/u-boot-net into next
Wolfgang Denk [Tue, 25 Aug 2009 20:57:10 +0000 (22:57 +0200)]
Merge branch 'master' into next
Wolfgang Denk [Tue, 25 Aug 2009 20:54:01 +0000 (22:54 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx
Wolfgang Denk [Tue, 25 Aug 2009 20:51:40 +0000 (22:51 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-blackfin
Kim Phillips [Mon, 24 Aug 2009 19:32:26 +0000 (14:32 -0500)]
net: tsec - handle user interrupt while waiting for PHY auto negotiation to complete
if you don't have firmware installed for the PHY to come to life, this
wait can be painful - let's give the option to avoid it if we want.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Robin Getz [Thu, 20 Aug 2009 14:50:20 +0000 (10:50 -0400)]
Add Transfer Size Option to tftp
Optionally add RFC 2349 "Transfer Size Option", so we can minimize the
time spent sending data over the UART (now print a single line during a
tftp transfer).
- If turned on (CONFIG_TFTP_TSIZE), U-Boot asks for the size of the file.
- if receives the file size, a single line (50 chars) are printed.
one hash mark == 2% of the file downloaded.
- if it doesn't receive the file size (the server doesn't support RFC
2349, prints standard hash marks (one mark for each UDP frame).
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Robin Getz [Mon, 24 Aug 2009 14:33:39 +0000 (10:33 -0400)]
Add debug message for Blackfin Ethernet Rx function.
Add a simple print for the Blackfin's Ethernet Rx function,
so we can debug incomming Ethernet functions easier.
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Ben Warren [Tue, 25 Aug 2009 20:09:37 +0000 (13:09 -0700)]
Convert CS8900 Ethernet driver to CONFIG_NET_MULTI API
All in-tree boards that use this controller have CONFIG_NET_MULTI added
Also:
- changed CONFIG_DRIVER_CS8900 to CONFIG_CS8900
- changed CS8900_BASE to CONFIG_CS8900_BASE
- changed CS8900_BUS?? to CONFIG_CS8900_BUS??
- cleaned up line lengths
- modified VCMA9 command function that accesses the device
- removed MAC address initialization from lib_arm/board.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Tested-by: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>