Mario Six [Mon, 15 Jan 2018 10:08:11 +0000 (11:08 +0100)]
i2c: ihs_i2c: Make DM compatible
Make the ihs_i2c driver DM-compatible; for legacy boards, the old functions are
retained within #ifdefs.
No board uses the new DM driver yet; this patch only lays the foundation for
future support.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Mario Six [Mon, 15 Jan 2018 10:08:10 +0000 (11:08 +0100)]
i2c: ihs_i2c: Prepare DM conversion
Prepare the function interface of the ihs_i2c driver for DM conversion
in a future patch.
While we're at it, fix some style violations, and make the code more readable.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Mario Six [Mon, 15 Jan 2018 10:08:09 +0000 (11:08 +0100)]
i2c: fsl_i2c: Make live-tree compatible
Make the fsl_i2c driver compatible with a live device tree.
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Mario Six [Mon, 15 Jan 2018 10:08:08 +0000 (11:08 +0100)]
i2c: fsl_i2c: Remove inline declarations
Some functions in the fsl_i2c driver are declared as inline, even though
they are quite large, which needlessly increases the size of the
resulting binary.
This patch removes the inline declarations.
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Mario Six [Mon, 15 Jan 2018 10:08:07 +0000 (11:08 +0100)]
i2c: fsl_i2c: Fix style violations
Fix some style violations in the fsl_i2c I2C driver, and use shorter
type names for variables in some cases.
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Ulf Magnusson [Tue, 30 Jan 2018 13:07:05 +0000 (14:07 +0100)]
usb: ulpi: kconfig: Remove meaningless choice default
'default' on a choice refers to the symbol selected by default, not to
the choice mode, so 'default n' is meaningless.
No functional changes. Optional choices implicitly default to n mode
(and there is no way to make them default to another mode).
Discovered in Kconfiglib (https://github.com/ulfalizer/Kconfiglib),
which prints the following warning:
warning: the default selection n (undefined) of <choice> (defined at drivers/usb/ulpi/Kconfig:3) is not contained in the choice
I've added a corresponding warning to the C tools too, which is
currently in linux-next: https://patchwork.kernel.org/patch/9983667/
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Ulf Magnusson [Tue, 30 Jan 2018 13:04:43 +0000 (14:04 +0100)]
am335x, shc: kconfig: Fix misspelled choice default
There is no EMMC symbol in the "enable different boot versions for the
shc board" choice. SHC_EMMC was probably intended.
No functional changes. Kconfig choices fall back on using the first
(visible) symbol in the choice as the default if the default symbol is
not visible.
Discovered in Kconfiglib (https://github.com/ulfalizer/Kconfiglib),
which prints the following warning:
warning: the default selection EMMC (undefined) of <choice> (defined at board/bosch/shc/Kconfig:15) is not contained in the choice
I've added a corresponding warning to the C tools too, which is
currently in linux-next: https://patchwork.kernel.org/patch/9983667/
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Justin Hibbits [Tue, 30 Jan 2018 04:23:36 +0000 (22:23 -0600)]
Fix FreeBSD endian checks
FreeBSD, like OpenBSD, uses BIG_ENDIAN, LITTLE_ENDIAN, and BYTE_ORDER,
whereas Linux and compatibles use __-prefixed names. Define the names
the same as the OpenBSD block below it.
Tuomas Tynkkynen [Sat, 27 Jan 2018 18:28:40 +0000 (20:28 +0200)]
cmd: Make CONFIG_CMD_FPGA depend on CONFIG_FPGA
cmd/Makefile has:
ifdef CONFIG_FPGA
obj-$(CONFIG_CMD_FPGA) += fpga.o
endif
which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently
does nothing. Let's remove that Makefile conditional and instead express
this equivalent dependency in Kconfig, so a lot of redundant
# CONFIG_CMD_FPGA is not set
can be removed from board defconfigs that don't actually have an FPGA.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Tuomas Tynkkynen [Sat, 27 Jan 2018 18:28:39 +0000 (20:28 +0200)]
fpga: Resync various CONFIG_FPGA_* symbols
These are declared in Kconfig, but some #defines have crept in.
CONFIG_FPGA
CONFIG_FPGA_ALTERA
CONFIG_FPGA_CYCLON2
CONFIG_FPGA_SOCFPGA
CONFIG_FPGA_XILINX
CONFIG_FPGA_ZYNQMPPL
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Tom Rini [Mon, 5 Feb 2018 14:51:50 +0000 (09:51 -0500)]
usb: dwc2: make casts of ep->dma_buf consistent
In most places in the code we cast this to an unsigned long, but in one
place we cast to an unsigned int. For consistency and to fix a warning
on 64bit targets, always cast this to unsigned long. For the long term
we should however change the declaration of dma_buf.
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Jorge Ramirez-Ortiz [Sun, 4 Feb 2018 09:35:08 +0000 (10:35 +0100)]
MAINTAINERS: board: qcom: db410c, db820c: update email.
Update email address.
Signed-off-by: Jorge Ramirez-Ortiz <jramirez@baylibre.com>
Daniel Schwierzeck [Fri, 26 Jan 2018 15:31:07 +0000 (16:31 +0100)]
travis.yml: run buildman with option -E
This forces all compiler warnings to be treated as errors.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Daniel Schwierzeck [Fri, 26 Jan 2018 15:31:06 +0000 (16:31 +0100)]
travis.yml: fix 'set +e' in build script
The build script should not manipulate shell flags (especially '-e').
A non-zero exit value can also be catched with 'cmd || ret=$?'.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Daniel Schwierzeck [Fri, 26 Jan 2018 15:31:05 +0000 (16:31 +0100)]
buildman: add option -E for treating compiler warnings as errors
Add a new option '-E' for treating all compiler warnings as errors.
Eventually this will pass 'KCFLAGS=-Werror' to Kbuild.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Daniel Schwierzeck [Fri, 26 Jan 2018 15:31:04 +0000 (16:31 +0100)]
README: add doc for how to supply user specific compiler flags to Kbuild
Probably not all users are aware of this possibility, thus add a
pointer to the README. Also add a useful example.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Maxime Ripard [Fri, 2 Feb 2018 20:45:23 +0000 (21:45 +0100)]
MAINTAINERS: Update email address for Maxime Ripard
Free Electrons is no more and is now known as Bootlin, change my email
address accordingly.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tom Rini [Sun, 4 Feb 2018 13:30:31 +0000 (08:30 -0500)]
Merge git://git.denx.de/u-boot-dm
Tom Rini [Sun, 4 Feb 2018 13:30:13 +0000 (08:30 -0500)]
Merge git://git.denx.de/u-boot-imx
Bryan O'Donoghue [Fri, 26 Jan 2018 16:27:58 +0000 (16:27 +0000)]
imx: mx7: run sec_init for CAAM RNG
This patch adds a sec_init call into arch_misc_init(). Doing so in
conjunction with the patch "drivers/crypto/fsl: assign job-rings to
non-TrustZone" enables use of the CAAM in Linux when OPTEE/TrustZone is
active.
u-boot will initialise the RNG and assign ownership of the job-ring
registers to a non-TrustZone context. With recent changes by Lukas Auer to
fully initialize the RNG in sec_init() this means that u-boot will hand-off
the CAAM in a state that Linux then can use the CAAM without touching the
reserved DECO registers.
This change is safe both for the OPTEE/TrustZone boot path and the regular
non-OPTEE/TrustZone boot path.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Marco Franchi <marco.franchi@nxp.com>
Cc: Vanessa Maegima <vanessa.maegima@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Tested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Bryan O'Donoghue [Fri, 26 Jan 2018 16:27:14 +0000 (16:27 +0000)]
drivers/crypto/fsl: assign job-rings to non-TrustZone
After enabling TrustZone various parts of the CAAM silicon become
inaccessible to non TrustZone contexts. The job-ring registers are designed
to allow non TrustZone contexts like Linux to still submit jobs to CAAM
even after TrustZone has been enabled.
The default job-ring permissions after the BootROM look like this for
job-ring zero.
ms=0x00008001 ls=0x00008001
The MS field is JRaMIDR_MS (job ring MID most significant).
Referring to "Security Reference Manual for i.MX 7Dual and 7Solo
Applications Processors, Rev. 0, 03/2017" section 8.10.4 we see that
JROWN_NS controls whether or not a job-ring is accessible from non
TrustZone.
Bit 15 (TrustZone) is the logical inverse of bit 3 hence the above value of
0x8001 shows that JROWN_NS=0 and TrustZone=1.
Clearly then as soon as TrustZone becomes active the job-ring registers are
no longer accessible from Linux, which is not what we want.
This patch explicitly sets all job-ring registers to JROWN_NS=1 (non
TrustZone) by default and to the Non-Secure MID 001. Both settings are
required to successfully assign a job-ring to non-secure mode. If a piece
of TrustZone firmware requires ownership of job-ring registers it can unset
the JROWN_NS bit itself.
This patch in conjunction with a modification of the Linux kernel to skip
HWRNG initialisation makes CAAM usable to Linux with TrustZone enabled.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Alex Porosanu <alexandru.porosanu@nxp.com>
Cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Cc: Aneesh Bansal <aneesh.bansal@nxp.com>
Link: https://github.com/OP-TEE/optee_os/issues/1408
Link: https://tinyurl.com/yam5gv9a
Tested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Eran Matityahu [Fri, 26 Jan 2018 14:11:37 +0000 (16:11 +0200)]
i2c: imx: Take mx6dqp in consideration in the I2C_PADS_INFO macro
We should take the MX6DP and MX6QP options in consideration
in the I2C_PADS_INFO macro.
Based on a patch by Pierluigi Passaro <pierluigi.p@variscite.com>
Signed-off-by: Eran Matityahu <eran.m@variscite.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Eran Matityahu [Fri, 26 Jan 2018 14:09:55 +0000 (16:09 +0200)]
iomux-v3: Take mx6dqp in consideration for imx_iomux_v3_setup_pad()
We should take the MX6DP and MX6QP options in consideration
when defining imx_iomux_v3_setup_pad().
Based on a patch by Pierluigi Passaro <pierluigi.p@variscite.com>
Signed-off-by: Eran Matityahu <eran.m@variscite.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Fabio Estevam [Sun, 21 Jan 2018 17:57:32 +0000 (15:57 -0200)]
doc: mxc_hab: Improve the config option list
The original text is from the time that the config options were not
converted to Kconfig.
After the conversion to Kconfig only CONFIG_SECURE_BOOT and
CONFIG_CMD_DEKBLOB need to be selected by the user.
The other config options are automatically selected by the Kconfig
logic.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Breno Lima <breno.lima@nxp.com>
Stefan Agner [Thu, 25 Jan 2018 12:56:48 +0000 (13:56 +0100)]
arm: dts: imx6ull: move input include to base device tree
The input keycode KEY_POWER is used in the imx6ull.dtsi file,
hence include the input header where used.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Fabio Estevam [Mon, 29 Jan 2018 13:11:57 +0000 (11:11 -0200)]
mx6sabresd: Add fastboot support
fastboot tool is a convenient way to flash the eMMC, so
add support for it.
Examples of usages:
On the mx6sabresd:
=> fastboot 0
On the Linux PC connected via USB:
$ sudo fastboot getvar bootloader-version -i 0x0525
bootloader-version: U-Boot 2018.01-00550-g7517cfe
finished. total time: 0.000s
$ sudo fastboot reboot -i 0x0525
(this causes the mx6sabresd to reboot)
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Fabio Estevam [Sun, 28 Jan 2018 14:49:03 +0000 (12:49 -0200)]
mx6sabresd: Select CONFIG_CMD_USB_MASS_STORAGE
Select CONFIG_CMD_USB_MASS_STORAGE so that the 'ums' can be used.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Fabio Estevam [Sun, 28 Jan 2018 14:49:02 +0000 (12:49 -0200)]
mx6sabre_common: Allow building CONFIG_USB_FUNCTION_MASS_STORAGE
Selecting CONFIG_USB_FUNCTION_MASS_STORAGE=y in the defconfig leads to
the following error:
cmd/built-in.o: In function `do_usb_mass_storage':
cmd/usb_mass_storage.c:217: undefined reference to `fsg_main_thread'
cmd/usb_mass_storage.c:170: undefined reference to `fsg_init'
CONFIG_USB_FUNCTION_MASS_STORAGE option is built only for
the non-SPL case as per the logic in drivers/usb/gadget/Makefile,
so remove the incorrect CONFIG_SPL ifdefery to fix the build
failure.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Soeren Moch [Sun, 28 Jan 2018 11:26:34 +0000 (12:26 +0100)]
board: tbs2910: add private imx config
Add board specific imx config file with recommended IPU Qos settings
and adapted DDR configuration.
Signed-off-by: Soeren Moch <smoch@web.de>
Michael Trimarchi [Thu, 25 Jan 2018 13:06:11 +0000 (14:06 +0100)]
imx: mx25: Remove SION bit in all pin-mux that are safe
SION bit should be used in the situation that we need
to read back the value of a pin and should not be set by
default macro.
We get some malfunction as raised by following thread
https://www.spinics.net/lists/linux-usb/msg162574.html
As reported by this application note:
https://www.nxp.com/docs/en/application-note/AN5078.pdf
The software input on (SION) bit is an option to force an input
path to be active regardless of the value driven by the
corresponding module. It is used when the nature direction
of a pin depending on selected alternative function is an output,
but it is needed to read the real logic value on a pin.
The SION bit can be used in:
• Loopback: the module of a selected alternative function drives
the pad and also receives the pad value as an input
• GPIO capture: the module of a selected alternative function
drives the pin and the value is captured by the GPIO
SION bit is not necessary when the pin is configured as a peripheral
apart specific silicon bug. If an application needs to have this
set, this should be done in board file or in dts file
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Peng Fan [Sun, 21 Jan 2018 11:00:25 +0000 (19:00 +0800)]
imx: mx7dsabresd: enable UHS and HS200
Enable UHS and HS200 for mx7dsabresd.
Read Speed improvement:
Kingston SD10VG2/16GB SDHC 3.0 card
22.2MB/s -> 73.7MB/s
eMMC5.0 MTFC8GACAEAM:
68MB/s -> 87MB/s
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Peng Fan [Sun, 21 Jan 2018 11:00:24 +0000 (19:00 +0800)]
mmc: fsl_esdhc: support SDR104 and HS200
Introduce SDR104 and HS200 support
The implementation takes linux kernel sdhci.c and sdhci-esdhc-imx.c
as reference.
- Implement esdhc_change_pinstate to dynamically change pad settings
- Implement esdhc_set_timing
- Implement esdhc_set_voltage to switch voltage
- Implement fsl_esdhc_execute_tuning to execute time process
- Enlarge the cfg->f_max to 200MHz.
- Parse fsl,tuning-step, fsl,tuning-start-tap and
fsl,strobe-dll-delay-target from device tree.
- Parse no-1-8-v property
- Introduce esdhc_soc_data to indicate the flags and caps
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Peng Fan [Sun, 21 Jan 2018 11:00:23 +0000 (19:00 +0800)]
ARM: dts: add pinmux and tuning settings for HS200/SDR104
The pinmux and tuning settings are from
https://source.codeaurora.org/external/imx/linux-imx/tree/arch/
arm/boot/dts/imx7s.dtsi?h=imx_4.9.11_1.0.0_ga
https://source.codeaurora.org/external/imx/linux-imx/tree/arch/
arm/boot/dts/imx7d-sdb.dts?h=imx_4.9.11_1.0.0_ga
To support HS200 and SDR104, we need change pinmux settings dynamically.
And configure tuning step and start tuning tap, otherwise you may
see tuning failure.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Peng Fan [Sun, 21 Jan 2018 11:00:22 +0000 (19:00 +0800)]
mmc: fsl_esdhc: add strobe and tuning entry
Add entries that will be used for tuning control.
The whole layout not changed, just expand reserved3[84] and
rename other reservedx in sequence.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Eric Nelson [Thu, 18 Jan 2018 15:36:26 +0000 (08:36 -0700)]
mx6memcal: fix comment in board header file
The board header file included a reference to the starting point
from nitrogen6x.h, but since so much changed, the file bears
little resemblance to that file.
Signed-off-by: Eric Nelson <eric@nelint.com>
Eric Nelson [Thu, 18 Jan 2018 14:47:32 +0000 (07:47 -0700)]
mx6memcal: enable SDP support
The initial implementation of mx6memcal reset the CPU after
running the memory calibration procedure because the generic
board has no information about which boot devices are available.
Now that we have SDP support in SPL, use it to allow a full
U-Boot to be uploaded (i.e. to use "mtest").
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Eric Nelson [Thu, 18 Jan 2018 14:47:31 +0000 (07:47 -0700)]
mx6memcal: launder through savedefconfig
This patch just changes the order of configuration items in
mx6memcal_defconfig to match the Kconfig layout, making it easier
to track changes made using menuconfig.
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Patrick Bruenn [Tue, 16 Jan 2018 06:59:04 +0000 (07:59 +0100)]
arm: imx: mx53loco: remove usage of mx53_dram_size
Static variables are not available during board_init_f().
'static uint32_t mx53_dram_size[2];' was used in board specific
dram_init(), dram_init_banksize() and get_effective_memsize() to avoid
multiple calls to get_ram_size().
Reused dram initialization functions from arch/arm/mach-imx/mx5/mx53_dram.c
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Patrick Bruenn [Tue, 16 Jan 2018 06:59:03 +0000 (07:59 +0100)]
arm: imx: m53evk: remove usage of mx53_dram_size
Static variables are not available during board_init_f().
'static uint32_t mx53_dram_size[2];' was used in board specific
dram_init(), dram_init_banksize() and get_effective_memsize() to avoid
multiple calls to get_ram_size().
Reused dram initialization functions from arch/arm/mach-imx/mx5/mx53_dram.c
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Patrick Bruenn [Tue, 16 Jan 2018 06:59:02 +0000 (07:59 +0100)]
arm: imx: cx9020: move dram init into common place
Move dram_init(), dram_init_banksize() and get_effective_memsize() to
arch/arm/mach-imx/mx5/mx53_dram.c, where it can be reused by m53evk and
mx53loco.
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Patrick Bruenn [Tue, 16 Jan 2018 06:59:01 +0000 (07:59 +0100)]
arm: imx: cx9020: remove usage of mx53_dram_size
Static variables are not available during board_init_f().
'static uint32_t mx53_dram_size[2];' was used in board specific
dram_init(), dram_init_banksize() and get_effective_memsize() to avoid
multiple calls to get_ram_size().
However multiple calls are better than undefined behavior...
This fixes:
https://lists.denx.de/pipermail/u-boot/2017-November/313214.html
https://lists.denx.de/pipermail/u-boot/2017-December/314480.html
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Nandor Han [Wed, 10 Jan 2018 19:31:38 +0000 (20:31 +0100)]
board,ge,bx50v3 - rtc time validation
Validate the time at startup:
- in case rtc error add to kernel command line RTC_ERROR
- clamp date to 1-Jan-2036
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Ian Ray [Wed, 10 Jan 2018 19:31:37 +0000 (20:31 +0100)]
configs: ge_bx50v3: automatic partition selection and video output failure message
The exact definition of a successful boot is defined by user-space.
Determine the boot partition automatically. A partition is selected if
file `/boot/bootcause/firstboot' exists (meaning that the partition has
freshly installed software) OR if file `/boot/fitImage' exists.
When userspace determines that new software was successfully installed,
it must (1) delete `/boot/fitImage' on the _inactive_ partition and (2)
remove `/boot/bootcause/firstboot'.
Enable video, but do not display logos or other version information.
Silence kernel console logging by default.
Print a message to VGA screen in case of boot failure and reset bootcount
to allow the user to attempt boot again.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Hannu Lounento [Wed, 10 Jan 2018 19:31:36 +0000 (20:31 +0100)]
board: ge: bx50v3: mount rootfs read-only
Change the kernel command line to mount the root filesystem read-only in
order to be able to run filesystem check on it on boot.
Signed-off-by: Hannu Lounento <hannu.lounento@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Ian Ray [Wed, 10 Jan 2018 19:31:35 +0000 (20:31 +0100)]
configs: ge_bx50v3: enable bootcount
Enable bootcount using an EXT file.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Ian Ray [Wed, 10 Jan 2018 19:31:34 +0000 (20:31 +0100)]
config: ge_bx50v3: read boot script
Read boot script from shared partition, if available.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Ian Ray [Wed, 10 Jan 2018 19:31:33 +0000 (20:31 +0100)]
board: ge: bx50v3: Support FIT and select configuration based on VPD
Modify configuration to support FIT. Set variable `confidx' from VPD,
in order to load the correct device tree. Modify/simplify U-Boot
environment to support loading FIT image.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Martyn Welch [Wed, 10 Jan 2018 19:31:32 +0000 (20:31 +0100)]
board: ge: bx50v3: Enable hardware watchdog
Enable the hardware watchdog on bx50v3 to cause it to reset in the event
the board hangs.
Configure GPIO_9 pin as WDOG1_B so that a watchdog timeout results in a
full system reset.
The watchdog is used and reconfigured by systemd approximately 1.7 seconds
into boot. Adding a few seconds for U-Boot and a few more seconds as a
safety margin.
Note that the PCIe controller is _not_ put back into a safe state prior
to board reset. This is a problem if board reset is implemented as CPU
reset.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Hannu Lounento [Wed, 10 Jan 2018 19:31:31 +0000 (20:31 +0100)]
board: ge: bx50v3: program MAC address to I210
There are two I210s on the b850v3 and one on the b450v3 and b650v3.
One is connected to Marvell 88e6240 which is already programmed.
Follow the flow documented in doc/README.enetaddr: set the
enet[0-9]*addr environment variable and let the driver program the
hardware.
The mapping from the driver's index to the environment variable's name
is documented in README: Note for Redundant Ethernet Interfaces. It is
assumed that eth_devices for the controllers on the board are always
indexed in the same order.
The environment variables are removed after programming the hardware
because the variables seem to influence MAC addresses also after U-Boot.
Specifically the MAC address of FEC (MC interface) would be incorrectly
set: 'ethaddr', which maps to the first I210 chip and is set to I210's
default address read from the driver by eth_write_hwaddr in eth_legacy.c
because the variable is undefined (not set even by bx50v3.c), would
result in the eth0 interface's MAC address to be set to I210's default
address.
Signed-off-by: Hannu Lounento <hannu.lounento@ge.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Martyn Welch [Wed, 10 Jan 2018 19:31:30 +0000 (20:31 +0100)]
board: ge: bx50v3: move FEC MAC address programming to driver
Instead of programming the hardware directly in the board
implementation, follow the flow documented in doc/README.enetaddr: set
the enet[0-9]*addr environment variable and let the driver program the
hardware.
This avoids duplicating the implementation as it already exists in the
driver (drivers/net/fec_mxc.c: fec_set_hwaddr).
The mapping from the driver's index to the environment variable's name
is documented in README: Note for Redundant Ethernet Interfaces. It is
assumed that eth_devices for the controllers on the board are always
indexed in the same order, i.e. FEC always has the index 2.
The FEC driver does *not* set the flag Set MAC Address on Transmit (bit
set_eth0_mac_address used to do but this is unnecessary as the Linux
networking stack fills in the MAC address.
Signed-off-by: Hannu Lounento <hannu.lounento@ge.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Ian Ray [Wed, 10 Jan 2018 19:31:29 +0000 (20:31 +0100)]
configs: Add network device support for bx50v3 products
Modify b450v3, b650v3 and b850v3 defconfigs to enable the network devices
found in these products.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Martyn Welch [Wed, 10 Jan 2018 19:31:28 +0000 (20:31 +0100)]
board: ge: Enable access to i2c bus 1 and 2
The change in i2c configuration added to support access to the VPD has
inadvertantly caused access to i2c buses 1 & 2 to be lost. This has
resulted in the configuration for the PMIC to be attempted on the wrong
bus and thus isn't taking effect.
Add the required configuration to return access to buses 1 & 2. In order
to ensure that any users of the bus numbering prior to addition in VPD
patches work, add buses before configuration related to mux on bus 0 and
tweak VPD bus usage to fit new numbering scheme.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Nandor Han [Wed, 10 Jan 2018 19:31:27 +0000 (20:31 +0100)]
rtc: adding RX8010SJ rtc driver
Add a new driver for RX8010SJ rtc chip. The driver implements both
formats of U-Boot driver model.
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Hannu Lounento [Wed, 10 Jan 2018 19:31:26 +0000 (20:31 +0100)]
net: e1000: implement eth_write_hwaddr
Implement programming MAC address to the hardware, i.e. external flash
seen as EEPROM.
MAC address is only written if it differs from what is already stored in
flash or if reading the current MAC address fails.
Signed-off-by: Hannu Lounento <hannu.lounento@ge.com>
CC: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Hannu Lounento [Wed, 10 Jan 2018 19:31:25 +0000 (20:31 +0100)]
net: e1000: split e1000_read_mac_addr
Split the implementation of e1000_read_mac_addr into eeprom and register
versions called by e1000_read_mac_addr.
This allows for calling e1000_read_mac_addr when MAC address is needed
with no constraints where it is read from, and for calling the register
and, especially, the eeprom version directly in order to specify where
to read the address from.
Signed-off-by: Hannu Lounento <hannu.lounento@ge.com>
CC: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Hannu Lounento [Wed, 10 Jan 2018 19:31:24 +0000 (20:31 +0100)]
net: e1000: add support for writing to EEPROM
Port functions for writing to EEPROM, updating the checksum and
committing data to flash from the Linux kernel igb driver.
Functions were ported from Linux 4.8-rc2 (
694d0d0bb20).
Signed-off-by: Hannu Lounento <hannu.lounento@ge.com>
CC: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Peng Fan [Wed, 10 Jan 2018 05:20:47 +0000 (13:20 +0800)]
imx: mx8m: add ddr controller memory map
Add ddrc memory map and enum types used in ddr initialization.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Peng Fan [Wed, 10 Jan 2018 05:20:46 +0000 (13:20 +0800)]
power: pmic/regulator allow dm be omitted by SPL
Allow the dm driver be omitted by SPL.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Peng Fan [Wed, 10 Jan 2018 05:20:45 +0000 (13:20 +0800)]
imx: imx8mq: add dtsi file
Add dtsi file for i.MX8MQ.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Ye Li [Wed, 10 Jan 2018 05:20:44 +0000 (13:20 +0800)]
net: fec: fix build warnings for 64bits support
When building for 64bits system, we get some warnings about type
cast between pointer and integer. This patch eliminates the warnings
by using ulong/long type which is 32bits on 32bits system or 64bits on
64bits system.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Peng Fan [Wed, 10 Jan 2018 05:20:43 +0000 (13:20 +0800)]
net: fec: do not access reserved register for i.MX8M
The MIB RAM and FIFO receive start register does not exist on
i.MX8M. Accessing these register will cause system hang.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Peng Fan [Wed, 10 Jan 2018 05:20:42 +0000 (13:20 +0800)]
gpio: mxc: add i.MX8M support
Add i.MX8M GPIO support.
There are 4 GPIO banks on i.MX8M.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Peng Fan [Wed, 10 Jan 2018 05:20:41 +0000 (13:20 +0800)]
imx: lcdif: include i.MX8M
Include i.MX8M in lcdif register layout map.
Also included i.MX7ULP in this patch, since share same with i.MX8M.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Peng Fan [Wed, 10 Jan 2018 05:20:40 +0000 (13:20 +0800)]
mmc: fsl_esdhc: support i.MX8M
Support i.MX8M in fsl esdhc driver.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Peng Fan [Wed, 10 Jan 2018 05:20:39 +0000 (13:20 +0800)]
misc: ocotp: add i.MX8M support
i.MX8M OCOTP follow same flow as i.MX6Q, but it has 64 banks
and each bank 4 words.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Peng Fan [Wed, 10 Jan 2018 05:20:38 +0000 (13:20 +0800)]
imx: makefile: compile files for i.MX8M
Compile files for i.MX8M
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Peng Fan [Wed, 10 Jan 2018 05:20:37 +0000 (13:20 +0800)]
imx: mx8m: add soc related settings and files
Add SoC level initialization code
- arch_cpu_init
- mmu table
- detect cpu revision
- reset cpu and wdog settings
- timer init
- wdog settings
- lowlevel init to save/restore registers
- a few dummy header file to avoid build failure
- ft_system_setup
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Peng Fan [Wed, 10 Jan 2018 05:20:36 +0000 (13:20 +0800)]
imx: mx7: move mmc env code to mmc_env.c
The mx7 mmc env code is shared by i.MX8M, so move it to mmc_env.c.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Wed, 10 Jan 2018 05:20:35 +0000 (13:20 +0800)]
imx: cpu: support get_boot_device for i.MX8M
Enable get_boot_device for i.MX8M, it supports boot type USB.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Peng Fan [Wed, 10 Jan 2018 05:20:34 +0000 (13:20 +0800)]
imx: mx7: move get_boot_device to cpu.c
Move get_boot_device to cpu.c to prepare adding i.MX8M support,
because i.MX8M share same code with i.MX7.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Peng Fan [Wed, 10 Jan 2018 05:20:33 +0000 (13:20 +0800)]
imx: bootaux: support i.MX8M
Add i.MX8M support. Because i.MX8M use SiP call trap
to Arm Trusted Firmware to handle M4, so use #ifdef
to avoid build error on i.MX6/7.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Wed, 10 Jan 2018 05:20:32 +0000 (13:20 +0800)]
imx: cleanup bootaux
Move i.MX6/7 bootaux code to imx_bootaux.c.
The i.MX6/7 has different src layout, so define M4 reg offset
to ease the cleanup. Redefine the M4 related BIT for share
common code.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Peng Fan [Wed, 10 Jan 2018 05:20:31 +0000 (13:20 +0800)]
imx: refactor imx_get_mac_from_fuse
Move imx_get_mac_from_fuse to a new mac.c for i.MX6/7.
Since fuse regs structure are different for i.MX6/7, use mac
address offset in code and define a new local struture
imx_mac_fuse.
Also sort the config order.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Peng Fan [Wed, 10 Jan 2018 05:20:30 +0000 (13:20 +0800)]
imx: cpu: add cpu speed/grade for i.MX8M
Use more general enum types for speed grade.
Refine get_cpu_speed_grade_hz to support i.MX8M.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Peng Fan [Wed, 10 Jan 2018 05:20:29 +0000 (13:20 +0800)]
imx: cpu: move speed/temp to common cpu
The i.MX7 cpu speed/temp code could be reused on i.MX8M,
so move them to common cpu code.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Peng Fan [Wed, 10 Jan 2018 05:20:28 +0000 (13:20 +0800)]
imx: add pad settings bit definition for i.MX8M
Add pad settings bit definition for i.MX8M.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Peng Fan [Wed, 10 Jan 2018 05:20:27 +0000 (13:20 +0800)]
imx: add i.MX8MQ SoC Revision and is_mx8m helper
Add i.MX8MQ SoC Revision
Add is_mx8m helper
The 7ULP is a dummy number, so use 0xEx.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Peng Fan [Wed, 10 Jan 2018 05:20:26 +0000 (13:20 +0800)]
imx: spl: implement spl_boot_device for i.MX8M
Implement spl_boot_device for i.MX8M.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Peng Fan [Wed, 10 Jan 2018 05:20:25 +0000 (13:20 +0800)]
imx: cpu: update cpu file to support i.MX8M
Update get_reset_cause to reflect i.MX8M
Compile out get_ahb_clk and set_chipselect_size for i.MX8M
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Peng Fan [Wed, 10 Jan 2018 05:20:24 +0000 (13:20 +0800)]
imx: boot_mode: add USB_BOOT entry
Add USB_BOOT entry.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Peng Fan [Wed, 10 Jan 2018 05:20:23 +0000 (13:20 +0800)]
imx: add sip function
Add SiP (Silicon Provider) services function to issue
SMC call to Arm Trusted Firmware.
More SiP information could be found in
https://github.com/ARM-software/arm-trusted-firmware/blob/master/
docs/arm-sip-service.rst
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Peng Fan [Wed, 10 Jan 2018 05:20:22 +0000 (13:20 +0800)]
imx: mx8m: add clock driver
Add clock driver to support i.MX8M.
There are two kind PLLs, FRAC pll and SSCG pll. ROM already
configured SYS PLL1/2, we only need to configure the output.
ocotp/i2c/pll decoding and configuration/usdhc/lcdif/dram pll/
enet clock are configured in the code.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Peng Fan [Wed, 10 Jan 2018 05:20:21 +0000 (13:20 +0800)]
imx: mx8m: add pin header file
Add pin header file for i.MX8M
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Peng Fan [Wed, 10 Jan 2018 05:20:20 +0000 (13:20 +0800)]
imx: mx8m: add register definition header file
Add register definition header file for i.MX8M
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Peng Fan [Wed, 10 Jan 2018 05:20:19 +0000 (13:20 +0800)]
imx: add i.MX8M into Kconfig
Add i.MX8M into Kconfig, create a new folder mx8m
dedicated for i.MX8M.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Jagan Teki [Tue, 9 Jan 2018 18:49:53 +0000 (00:19 +0530)]
configs: icore: enable nand on mmc defconfig
Enable nand on mmc defconfig, so-that preparing nand
for writing/updating bootimage, Linux becomes easy.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Jagan Teki [Tue, 9 Jan 2018 18:49:52 +0000 (00:19 +0530)]
configs: enable spl support wrt env device
nand device needed for mmc config to access nand
for write and update so enabling SPL_SUPPORT to mmc
or nand is wrt to env device rather nand driver check.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Anson Huang [Sun, 7 Jan 2018 06:34:32 +0000 (14:34 +0800)]
imx: mx7: psci: add system power off support
Add i.MX7 PSCI system power off support, linux
kernel can use "poweroff" command to power off
system via SNVS, PMIC power will be disabled.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Anson Huang [Sun, 7 Jan 2018 06:34:31 +0000 (14:34 +0800)]
imx: mx7: psci: add system reset support
Add i.MX7 PSCI system reset support, linux
kernel can use "reboot" command to reset
system even wdog driver is disabled in kernel.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Anson Huang [Sun, 7 Jan 2018 06:34:30 +0000 (14:34 +0800)]
mx7_common: use psci 1.0 instead of 0.1
Use PSCI 1.0 instead of 0.1 to support more power
management feature like system reset, power off etc..
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Jagan Teki [Fri, 5 Jan 2018 18:32:04 +0000 (00:02 +0530)]
board: i.MX6QDL: add Engicam i.CoreM6 1.5 QDL MIPI starter kit
i.CoreM6 1.5 is an another i.CoreM6 QDL cpu modules which can be connected
to EDIMM starter kit design with eMMC and MIPI-CSI interfaces suitable for
Android and video capture application.
notable features:
CPU NXP i.MX6 S/DL/D/Q, Up to 4 x Cortex-A9@800MHz
Memory Up to 2 GB DDR3-1066
Video Interfaces Up to 1 Parallel Up to 2 LVDS HDMI 1.4
port 8 bit CSI INPUT MIPI-CSI INPUT
1 x 10/100 Ethernet interface, 2 x USB, 1 x PCIe, 1 x I2S etc
This patch adds support for Quad/Dual and DualLite/Solo SOM's on
MIPI starter kit with boot from SD and eMMC.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Heinrich Schuchardt [Mon, 22 Jan 2018 19:10:45 +0000 (20:10 +0100)]
log: add category LOGC_EFI
The EFI implementation does not fit into any of the existing categories.
Provide LOGC_EFI so that EFI related message can be filtered.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Thu, 28 Dec 2017 20:14:23 +0000 (13:14 -0700)]
log: Add a way to log error-return values
When functions return an error it propagates up the stack to the point
where it is reported. Often the error code provides enough information
about the root cause of the error that this is obvious what went wrong.
However in some cases the error may be hard to trace. For example if a
driver uses several devices to perform an operation, it may not be
obvious which one failed.
Add a log_ret() macro to help with this. This can be used to wrap any
error-return value. The logging system will then output a log record when
the original error is generated, making it easy to trace the call stack
of the error.
This macro can significantly impact code size, so its use is controlled
by a Kconfig option, which is enabled for sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Thu, 28 Dec 2017 20:14:22 +0000 (13:14 -0700)]
log: Add documentation for commands and formatting
Add some notes about recent new features.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Thu, 28 Dec 2017 20:14:21 +0000 (13:14 -0700)]
log: Add tests for the new log features
Add a test of the 'log format' and 'log rec' commands. This also covers
things like log_get_cat_by_name(), since they are used by these commands.
Fix a style nit in the tests also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Thu, 28 Dec 2017 20:14:20 +0000 (13:14 -0700)]
log: Add a command to output a log record
Add a 'log rec' command which allows a log record to be manually output.
This is useful for scripts which want full control over what is logged. It
also permits easy testing of the log system.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Thu, 28 Dec 2017 20:14:19 +0000 (13:14 -0700)]
log: Add a command to control the log output format
Add a 'log format' command which can display or change the log output
format. This is useful for changing how much information is displayed. The
ordering of the fields is fixed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Thu, 28 Dec 2017 20:14:18 +0000 (13:14 -0700)]
log: Update log_console to honour the log format
At present this just outputs the message. Update it to output whatever the
format requests.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Thu, 28 Dec 2017 20:14:17 +0000 (13:14 -0700)]
log: Add control over log formatting
It is useful to be able to control the output format of log records on the
console. As a starting point, add definitions for controlling which
elements of the log record are displayed. Use function and message as the
default, since these are the most useful fields.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Thu, 28 Dec 2017 20:14:16 +0000 (13:14 -0700)]
log: Add functions to convert IDs to/from names
Category and level both use an enum for their ID values. Add functions to
convert these IDs to strings and vice versa. This will allow the log to
output the strings instead of the (inscrutable) values.
At the same time, add a new 'driver-model' category, to cover core
driver-model functions and fix an incorrect value for LOGL_MAX.
Tests will be added with the new 'log' subcommands.
Signed-off-by: Simon Glass <sjg@chromium.org>
(Updated to correct clang warnings)