Philipp Zabel [Thu, 27 Jun 2013 09:59:01 +0000 (06:59 -0300)]
[media] coda: add CODA7541 decoding support
This patch enables decoding of h.264 and mpeg4 streams on CODA7541.
Queued output buffers are immediately copied into the bitstream
ringbuffer. A device_run can be scheduled whenever there is either
enough compressed bitstream data, or the CODA is in stream end mode.
Each successful device_run, data is read from the bitstream ringbuffer
and a frame is decoded into a free internal framebuffer. Depending on
reordering, a possibly previously decoded frame is marked as display
frame, and at the same time the display frame from the previous run
is copied out into a capture buffer by the rotator hardware.
The dequeued capture buffers are counted to send the EOS signal to
userspace with the last frame. When userspace sends the decoder stop
command or enqueues an empty output buffer, the stream end flag is
set to allow decoding the remaining frames in the bitstream
ringbuffer.
The enum_fmt/try_fmt functions return fixed capture buffer sizes
while the output queue is streaming, to allow better autonegotiation
in userspace.
A per-context buffer mutex is used to lock the picture run against
buffer dequeueing: if a job gets queued, then streamoff dequeues
the last buffer, and then device_run is called, bail out. For that
the interrupt handler has to be threaded.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel [Fri, 21 Jun 2013 06:55:33 +0000 (03:55 -0300)]
[media] coda: split encoder specific parts out of device_run and irq_handler
Add coda_prepare_encode() and coda_finish_encode() functions. They are called
from coda_device_run() and coda_irq_handler(), respectively, before and after
the hardware picture run. This should make the following decoder support patch
easier to read, which will add the coda_prepare/finish_decode() equivalents.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel [Fri, 21 Jun 2013 06:55:32 +0000 (03:55 -0300)]
[media] coda: dynamic IRAM setup for decoder
This sets up IRAM areas used as temporary memory for the different
hardware units depending on the frame size.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Johannes Koch [Wed, 17 Jul 2013 17:28:16 +0000 (14:28 -0300)]
[media] cx23885: Fix TeVii S471 regression since introduction of ts2020
Patch to make TeVii S471 cards use the ts2020 tuner, since ds3000 driver no
longer contains tuning code.
Signed-off-by: Johannes Koch <johannes@ortsraum.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Sean Young [Mon, 8 Jul 2013 20:33:09 +0000 (17:33 -0300)]
[media] lirc: make transmit interface consistent
All lirc drivers that can transmit, return EINVAL when they are passed
more than IR data than they can send. That is, except for two drivers
which I touched.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Sean Young [Mon, 8 Jul 2013 20:33:11 +0000 (17:33 -0300)]
[media] lirc: validate transmission ir data
The lirc interface allows 255 u32 spaces and pulses, which are usec. If
the driver can handle this (e.g. winbond-cir) you can produce hours of
meaningless IR data and there is no method of interrupting it.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Sean Young [Mon, 8 Jul 2013 20:33:10 +0000 (17:33 -0300)]
[media] rc: allowed_protos now is a bit field
This one must have missed the conversion "
c003ab1b [media] rc-core:
add separate defines for protocol bitmaps and numbers".
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Sean Young [Mon, 8 Jul 2013 20:33:08 +0000 (17:33 -0300)]
[media] redrat3: errors on unplug
In an usb disconnect handler, the urbs have already been cancelled so the
attempt to disable the IR receiver just results in errors:
[ 899.638862] redrat3 7-2:1.0: redrat3_send_cmd: Error sending rr3 cmd res -110, data 0
[ 899.638870] redrat3 7-2:1.0: redrat3_disable_detector: detector status: 251, should be 0
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Sylwester Nawrocki [Thu, 11 Jul 2013 08:20:15 +0000 (05:20 -0300)]
[media] DocBook: Fix typo in V4L2_CID_JPEG_COMPRESSION_QUALITY reference
Replace the erroneous V4L2_CID_JPEG_IMAGE_QUALITY control name
with V4L2_CID_JPEG_COMPRESSION_QUALITY.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Sylwester Nawrocki [Mon, 22 Jul 2013 11:01:33 +0000 (08:01 -0300)]
[media] V4L: Merge struct v4l2_async_subdev_list with struct v4l2_subdev
By integrating the v4l2-async API internals a bit more with
the core overall the v4l2-async code becomes a bit simpler
and easier to follow.
Acked-and-tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Sylwester Nawrocki [Fri, 19 Jul 2013 15:31:10 +0000 (12:31 -0300)]
[media] V4L: Rename subdev field of struct v4l2_async_notifier
This is a purely cosmetic change. Since the 'subdev' member
points to an array of subdevs make it more explicit by
renaming to the plural form.
Acked-and-tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Sylwester Nawrocki [Fri, 19 Jul 2013 15:21:29 +0000 (12:21 -0300)]
[media] V4L: Add V4L2_ASYNC_MATCH_OF subdev matching type
Add support for matching by device_node pointer. This allows
the notifier user to simply pass a list of device_node pointers
corresponding to sub-devices.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Sylwester Nawrocki [Fri, 19 Jul 2013 15:14:46 +0000 (12:14 -0300)]
[media] V4L: Rename v4l2_async_bus_* to v4l2_async_match_*
enum v4l2_async_bus_type also selects a method subdevs are matched
in the notification handlers, rename it to v4l2_async_match_type
so V4L2_ASYNC_MATCH_OF entry can be further added for matching by
device tree node pointer.
Acked-and-tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Sylwester Nawrocki [Fri, 19 Jul 2013 15:08:08 +0000 (12:08 -0300)]
[media] V4L: Drop bus_type check in v4l2-async match functions
These match_* functions are internal callbacks and are always
invoked only after checking asd->bus_type. So drop redundant
checks in match_i2c() and match_platform() functions.
Acked-and-tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Maxim Levitsky [Sun, 7 Jul 2013 23:22:47 +0000 (20:22 -0300)]
[media] ene_ir: don't use pr_debug after all
This way to only way to get debug info is to use dynamic debug, but I
left debugging prints to debug hardware issues, and so I want this to be
enabled by module param.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Maxim Levitsky [Sun, 7 Jul 2013 23:22:46 +0000 (20:22 -0300)]
[media] ene_ir: disable the device if wake is disabled
It doesn't hurt and on my notebook despite clearing the
wake flag the remote still wakes up the system.
This way it doesn't.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Maxim Levitsky [Sun, 7 Jul 2013 23:22:45 +0000 (20:22 -0300)]
[media] ene_ir: Fix interrupt line passthrough to hardware
While we can delay IRQ intialization, we need the interrupt number
right away because unusually hardware have programable interrupt number,
and thus we give it the number that was allocated by BIOS
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dan Carpenter [Wed, 26 Jun 2013 13:37:36 +0000 (10:37 -0300)]
[media] staging: lirc: clean error handling in probe()
We have reorganized the error handling into a simpler and more canonical
format.
Additionally we removed extra empty lines, switched to devm_kzalloc(), and
substitute 'minor' by 'ret' in the igorplugusb_remote_probe() function.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Alban Browaeys [Tue, 16 Jul 2013 22:06:46 +0000 (19:06 -0300)]
[media] em28xx: Fix vidioc fmt vid cap v4l2 compliance
Set fmt.pix.priv to zero in vidioc_try_fmt_vid_cap.
Catched by v4l2-compliance.
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
[hans.verkuil@cisco.com: dropping unnecessary change to g_fmt_vid_cap]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Ondrej Zary [Fri, 19 Jul 2013 16:46:18 +0000 (13:46 -0300)]
[media] radio-aztech: Implement signal strength detection and fix stereo detection
Current stereo detection code is wrong - it reads TUNED bit instead of STEREO bit.
Fix that and implement signal strength detection too.
Also remove useless s_stereo functionn.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Ondrej Zary [Fri, 19 Jul 2013 16:46:17 +0000 (13:46 -0300)]
[media] radio-aztech: Convert to generic lm7000 implementation
Aztech radio card is based on LM7001 chip which is (software) compatible with LM7000.
So remove the LM7000-specific code from the driver and use generic code.
Also found that the card does not have A0..A2 ISA pins connected, which means that the region size is 8 bytes.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Ondrej Zary [Tue, 14 May 2013 19:54:44 +0000 (16:54 -0300)]
[media] bttv: stop abusing mbox_we for sw_status
Kodicom 4400R and Geovision GV-800 code in bttv driver abuses mbox_we (int)
in struct bttv as char *.
Remove this hack and add a proper sw_status array to struct bttv instead.
This is a a preparation to remove mbox_we.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Ondrej Zary [Tue, 14 May 2013 19:54:43 +0000 (16:54 -0300)]
[media] tea575x-tuner: move HW init to a separate function
Move HW initialization to separate function to allow using the code without
the v4l parts. This is needed for use in the bttv driver.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Ezequiel Garcia [Thu, 18 Jul 2013 12:01:23 +0000 (09:01 -0300)]
[media] media: stk1160: Ignore unchanged standard set
This commit adds an early check to vidioc_s_std() to detect if the
new and current standards are equal, and exit with success in that
case.
This is needed to prevent userspace applications that might attempt
to re-set the same standard from failing if that's done when streaming
has started.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Ezequiel Garcia [Wed, 17 Jul 2013 07:43:22 +0000 (04:43 -0300)]
[media] stk1160: Allow to change input while streaming
Remove the check as there's no reason to prevent the input from
being set when the device is streaming. This allows surveillance
applications (such as motion, zoneminder, etc.) to configure the
input while streaming.
Reported-by: Sergey 'Jin' Bostandzhyan <jin@mediatomb.cc>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Wei Yongjun [Wed, 17 Jul 2013 01:01:12 +0000 (22:01 -0300)]
[media] usbtv: remove unused including <linux/version.h>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Vladimir Barinov [Mon, 15 Jul 2013 18:12:21 +0000 (15:12 -0300)]
[media] ml86v7667: override default field interlace order
ML86V7667 always transmits top field first for both PAL and NTSC -- that makes
application incorrectly treat interlaced fields when relying on the standard.
Hence we must set V4L2_FIELD_INTERLACED_TB format explicitly.
[Sergei: added a comment.]
Reported-by: Katsuya MATSUBARA <matsu@igel.co.jp>
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Katsuya MATSUBARA <matsu@igel.co.jp>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Lubomir Rintel [Fri, 12 Jul 2013 08:03:03 +0000 (05:03 -0300)]
[media] usbtv: Add S-Video input support
Alongside already existing Composite input.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Alexey Khoroshilov [Mon, 24 Jun 2013 18:57:37 +0000 (15:57 -0300)]
[media] tlg2300: fix checking firmware in poseidon_probe()
check_firmware() makes sure firmware is in a device.
It returns zero on success and error code otherwise.
Also it sets down_firmware flag to 1 if downloading occurs.
The only caller poseidon_probe() checks down_firmware flag and
returns 0 without any initialization if it is set.
That looks very strange, so the patch removes down_firmware argument
of check_firmware() and returns error code if check_firmware() fails
in poseidon_probe().
Not tested on real hardware.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Alexey Khoroshilov [Mon, 24 Jun 2013 18:57:36 +0000 (15:57 -0300)]
[media] tlg2300: implement error handling in poseidon_probe()
All poseidon init functions properly return error codes,
but they are ignored by poseidon_probe(). The patch implements
handling of error cases.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Libo Chen [Mon, 27 May 2013 01:31:59 +0000 (22:31 -0300)]
[media] drivers/media/radio/radio-maxiradio: Convert to module_pci_driver
use module_pci_driver instead of init/exit, make code clean
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Libin Yang [Wed, 3 Jul 2013 04:56:04 +0000 (01:56 -0300)]
[media] marvell-ccic: switch to resource managed allocation and request
This patch switchs to resource managed allocation and request in mmp-driver.
It can remove free resource operations.
Signed-off-by: Albert Wang <twang13@marvell.com>
Signed-off-by: Libin Yang <lbyang@marvell.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Libin Yang [Wed, 3 Jul 2013 04:56:03 +0000 (01:56 -0300)]
[media] marvell-ccic: add SOF / EOF pair check for marvell-ccic driver
This patch adds the SOFx/EOFx pair check for marvell-ccic.
When switching format, the last EOF may not arrive when stop streamning.
And the EOF will be detected in the next start streaming.
Must ensure clear the left over frame flags before every really start streaming.
Signed-off-by: Albert Wang <twang13@marvell.com>
Signed-off-by: Libin Yang <lbyang@marvell.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Libin Yang [Wed, 3 Jul 2013 04:56:02 +0000 (01:56 -0300)]
[media] marvell-ccic: add new formats support for marvell-ccic driver
This patch adds some planar formats support for marvell-ccic.
Signed-off-by: Albert Wang <twang13@marvell.com>
Signed-off-by: Libin Yang <lbyang@marvell.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Libin Yang [Wed, 3 Jul 2013 04:56:01 +0000 (01:56 -0300)]
[media] marvell-ccic: refine mcam_set_contig_buffer function
This patch refines mcam_set_contig_buffer() in mcam core.
It can remove redundant code line and enhance readability.
Signed-off-by: Albert Wang <twang13@marvell.com>
Signed-off-by: Libin Yang <lbyang@marvell.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Libin Yang [Wed, 3 Jul 2013 04:56:00 +0000 (01:56 -0300)]
[media] marvell-ccic: reset ccic phy when stop streaming for stability
This patch adds the reset ccic phy operation when stop streaming.
Stop streaming without reset ccic phy, the next start streaming
may be unstable.
Also need add CCIC2 definition when PXA688/PXA2128 support dual ccics.
Signed-off-by: Albert Wang <twang13@marvell.com>
Signed-off-by: Libin Yang <lbyang@marvell.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Libin Yang [Wed, 3 Jul 2013 04:55:59 +0000 (01:55 -0300)]
[media] marvell-ccic: add clock tree support for marvell-ccic driver
This patch adds the clock tree support for marvell-ccic.
Signed-off-by: Libin Yang <lbyang@marvell.com>
Signed-off-by: Albert Wang <twang13@marvell.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Libin Yang [Wed, 3 Jul 2013 04:55:58 +0000 (01:55 -0300)]
[media] marvell-ccic: add MIPI support for marvell-ccic driver
This patch adds the MIPI support for marvell-ccic.
Board driver should determine whether using MIPI or not.
Signed-off-by: Albert Wang <twang13@marvell.com>
Signed-off-by: Libin Yang <lbyang@marvell.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Lad, Prabhakar [Sat, 20 Jul 2013 05:21:06 +0000 (02:21 -0300)]
[media] media: i2c: adv7343: add OF support
add OF support for the adv7343 driver.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Lad, Prabhakar [Sat, 20 Jul 2013 05:21:05 +0000 (02:21 -0300)]
[media] media: i2c: adv7343: make the platform data members as array
This patch makes the platform data members as array wherever
possible, so as this makes easier while collecting the data
in DT case and read the entire array at once.
This patch also makes appropriate changes to board-da850-evm.c
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Lad, Prabhakar [Sat, 13 Jul 2013 07:50:30 +0000 (04:50 -0300)]
[media] media: davinci: vpss: convert to devm* api
Replace existing resource handling in the driver with managed
device resource, this ensures more consistent error values and
simplifies error paths.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Lad, Prabhakar [Sat, 13 Jul 2013 07:50:29 +0000 (04:50 -0300)]
[media] media: davinci: vpbe_display: convert to devm* api
Replace existing resource handling in the driver with managed
device resource, this ensures more consistent error values and
simplifies error paths.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Lad, Prabhakar [Sat, 13 Jul 2013 07:50:28 +0000 (04:50 -0300)]
[media] media: davinci: vpbe_osd: convert to devm_* api
Replace existing resource handling in the driver with managed
device resource, this ensures more consistent error values and
simplifies error paths.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Lad, Prabhakar [Sat, 13 Jul 2013 07:50:27 +0000 (04:50 -0300)]
[media] media: davinci: vpbe_venc: convert to devm_* api
Replace existing resource handling in the driver with managed
device resource, this ensures more consistent error values and
simplifies error paths.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Lad, Prabhakar [Tue, 25 Jun 2013 14:17:35 +0000 (11:17 -0300)]
[media] media: davinci: vpif: display: add V4L2-async support
Add support for asynchronous subdevice probing, using the v4l2-async API.
The legacy synchronous mode is still supported too, which allows to
gradually update drivers and platforms.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Lad, Prabhakar [Tue, 25 Jun 2013 14:17:34 +0000 (11:17 -0300)]
[media] media: davinci: vpif: capture: add V4L2-async support
Add support for asynchronous subdevice probing, using the v4l2-async API.
The legacy synchronous mode is still supported too, which allows to
gradually update drivers and platforms.
Signed-off-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Lad, Prabhakar [Mon, 24 Jun 2013 14:51:39 +0000 (11:51 -0300)]
[media] media: i2c: tvp514x: add support for asynchronous probing
Both synchronous and asynchronous tvp514x subdevice probing
is supported by this patch.
This patch also fixes the error path by calling
media_entity_cleanup() on failure in probe when
CONFIG_MEDIA_CONTROLLER is enabled.
Signed-off-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Lad, Prabhakar [Sat, 22 Jun 2013 16:44:14 +0000 (13:44 -0300)]
[media] media: i2c: tvp7002: add support for asynchronous probing
Both synchronous and asynchronous tvp7002 subdevice probing
is supported by this patch.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Lad, Prabhakar [Sat, 22 Jun 2013 09:07:37 +0000 (06:07 -0300)]
[media] media: i2c: adv7343: add support for asynchronous probing
Both synchronous and asynchronous adv7343 subdevice probing is supported by
this patch.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Lad, Prabhakar [Sat, 22 Jun 2013 08:46:35 +0000 (05:46 -0300)]
[media] media: i2c: ths8200: add OF support
add OF support for the ths8200 driver.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Lad, Prabhakar [Sat, 22 Jun 2013 08:46:34 +0000 (05:46 -0300)]
[media] media: i2c: ths8200: support asynchronous probing
This patch supports both synchronous and asynchronous
ths8200 subdevice probing.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel [Fri, 21 Jun 2013 06:55:31 +0000 (03:55 -0300)]
[media] coda: add bitstream ringbuffer handling for decoder
Add a bitstream ringbuffer using kfifo. Queued source buffers are to be copied
into the bitstream ringbuffer immediately and marked as done, if possible.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel [Fri, 21 Jun 2013 06:55:30 +0000 (03:55 -0300)]
[media] coda: update CODA7541 to firmware 1.4.50
This patch splits the global workbuf into a global tempbuf and a per-context
workbuf, adds the codec mode aux register, and restores the work buffer
pointer on commands. With the new firmware, there is only a single set of
read/write pointers which need to be restored between context switches.
This allows more than four active contexts at the same time.
All auxiliary buffers are now allocated through a helper function to avoid
code duplication.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel [Fri, 21 Jun 2013 06:55:29 +0000 (03:55 -0300)]
[media] coda: do not allocate maximum number of framebuffers for encoder
The encoder only ever needs two buffers, but we'll have to increase
CODA_MAX_FRAMEBUFFERS for the decoder.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel [Fri, 21 Jun 2013 06:55:28 +0000 (03:55 -0300)]
[media] coda: dynamic IRAM setup for encoder
This sets up IRAM areas used as temporary memory for the different
hardware units depending on the frame size.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel [Fri, 21 Jun 2013 06:55:27 +0000 (03:55 -0300)]
[media] coda: use vb2_set_plane_payload instead of setting v4l2_planes[0].bytesused directly
As stated in the vb2_buffer documentation, drivers should not directly fill
in v4l2_planes[0].bytesused, but should use the vb2_set_plane_payload()
function instead. No functional changes.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Antti Palosaari [Tue, 23 Jul 2013 12:15:31 +0000 (09:15 -0300)]
[media] dvb-usb-v2: fix Kconfig dependency when RC_CORE=m
It is not allowed to build driver as a build-in when RC_CORE
(remote controller support) is build as a module.
randconfig build error with next-
20130719, in drivers/media/usb
drivers/built-in.o: In function `dvb_usbv2_disconnect':
(.text+0x154b39): undefined reference to `rc_unregister_device'
drivers/built-in.o: In function `dvb_usbv2_init_work':
dvb_usb_core.c:(.text+0x155b2d): undefined reference to `rc_allocate_device'
dvb_usb_core.c:(.text+0x155c38): undefined reference to `rc_register_device'
dvb_usb_core.c:(.text+0x155c5b): undefined reference to `rc_free_device'
drivers/built-in.o: In function `anysee_rc_query':
anysee.c:(.text+0x157795): undefined reference to `rc_keydown'
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Philipp Zabel [Mon, 3 Jun 2013 07:23:48 +0000 (04:23 -0300)]
[media] mem2mem: add support for hardware buffered queue
On mem2mem decoders with a hardware bitstream ringbuffer, to drain the
buffer at the end of the stream, remaining frames might need to be decoded
from the bitstream buffer without additional input buffers being provided.
To achieve this, allow a queue to be marked as buffered by the driver, and
allow scheduling of device_runs when buffered ready queues are empty.
This also allows a driver to copy input buffers into their bitstream
ringbuffer and immediately mark them as done to be dequeued.
The motivation for this patch is hardware assisted h.264 reordering support
in the coda driver. For high profile streams, the coda can hold back
out-of-order frames, causing a few mem2mem device runs in the beginning, that
don't produce any decompressed buffer at the v4l2 capture side. At the same
time, the last few frames can be decoded from the bitstream with mem2mem device
runs that don't need a new input buffer at the v4l2 output side. The decoder
command ioctl can be used to put the decoder into the ringbuffer draining
end-of-stream mode.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Michael Krufky [Sun, 30 Jun 2013 15:43:58 +0000 (12:43 -0300)]
[media] dib0700: add support for PCTV 2002e & PCTV 2002e SE
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mauro Carvalho Chehab [Sun, 21 Jul 2013 23:21:51 +0000 (20:21 -0300)]
Merge tag 'v3.11-rc2' into patchwork
Linux 3.11-rc2
* tag 'v3.11-rc2': (9535 commits)
Linux 3.11-rc2
ext3: fix a BUG when opening a file with O_TMPFILE flag
ext4: fix a BUG when opening a file with O_TMPFILE flag
vfs: constify dentry parameter in d_count()
livelock avoidance in sget()
allow O_TMPFILE to work with O_WRONLY
Btrfs: fix wrong write offset when replacing a device
Btrfs: re-add root to dead root list if we stop dropping it
Btrfs: fix lock leak when resuming snapshot deletion
Btrfs: update drop progress before stopping snapshot dropping
arm64: use common reboot infrastructure
arm64: mm: don't treat user cache maintenance faults as writes
arm64: add '#ifdef CONFIG_COMPAT' for aarch32_break_handler()
arm64: Only enable local interrupts after the CPU is marked online
MIPS: kvm: Kconfig: Drop HAVE_KVM dependency from VIRTUALIZATION
um: remove dead code
um: siginfo cleanup
MIPS: Octeon: Fix DT pruning bug with pip ports
uml: Fix which_tmpdir failure when /dev/shm is a symlink, and in other edge cases
um: Fix wait_stub_done() error handling
...
Linus Torvalds [Sun, 21 Jul 2013 19:05:29 +0000 (12:05 -0700)]
Linux 3.11-rc2
Linus Torvalds [Sun, 21 Jul 2013 17:11:04 +0000 (10:11 -0700)]
Merge tag 'acpi-video-3.11' of git://git./linux/kernel/git/rafael/linux-pm
Pull ACPI video support fixes from Rafael Wysocki:
"I'm sending a separate pull request for this as it may be somewhat
controversial. The breakage addressed here is not really new and the
fixes may not satisfy all users of the affected systems, but we've had
so much back and forth dance in this area over the last several weeks
that I think it's time to actually make some progress.
The source of the problem is that about a year ago we started to tell
BIOSes that we're compatible with Windows 8, which we really need to
do, because some systems shipping with Windows 8 are tested with it
and nothing else, so if we tell their BIOSes that we aren't compatible
with Windows 8, we expose our users to untested BIOS/AML code paths.
However, as it turns out, some Windows 8-specific AML code paths are
not tested either, because Windows 8 actually doesn't use the ACPI
methods containing them, so if we declare Windows 8 compatibility and
attempt to use those ACPI methods, things break. That occurs mostly
in the backlight support area where in particular the _BCM and _BQC
methods are plain unusable on some systems if the OS declares Windows
8 compatibility.
[ The additional twist is that they actually become usable if the OS
says it is not compatible with Windows 8, but that may cause
problems to show up elsewhere ]
Investigation carried out by Matthew Garrett indicates that what
Windows 8 does about backlight is to leave backlight control up to
individual graphics drivers. At least there's evidence that it does
that if the Intel graphics driver is used, so we've decided to follow
Windows 8 in that respect and allow i915 to control backlight (Daniel
likes that part).
The first commit from Aaron Lu makes ACPICA export the variable from
which we can infer whether or not the BIOS believes that we are
compatible with Windows 8.
The second commit from Matthew Garrett prepares the ACPI video driver
by making it initialize the ACPI backlight even if it is not going to
be used afterward (that is needed for backlight control to work on
Thinkpads).
The third commit implements the actual workaround making i915 take
over backlight control if the firmware thinks it's dealing with
Windows 8 and is based on the work of multiple developers, including
Matthew Garrett, Chun-Yi Lee, Seth Forshee, and Aaron Lu.
The final commit from Aaron Lu makes us follow Windows 8 by informing
the firmware through the _DOS method that it should not carry out
automatic brightness changes, so that brightness can be controlled by
GUI.
Hopefully, this approach will allow us to avoid using blacklists of
systems that should not declare Windows 8 compatibility just to avoid
backlight control problems in the future.
- Change from Aaron Lu makes ACPICA export a variable which can be
used by driver code to determine whether or not the BIOS believes
that we are compatible with Windows 8.
- Change from Matthew Garrett makes the ACPI video driver initialize
the ACPI backlight even if it is not going to be used afterward
(that is needed for backlight control to work on Thinkpads).
- Fix from Rafael J Wysocki implements Windows 8 backlight support
workaround making i915 take over bakclight control if the firmware
thinks it's dealing with Windows 8. Based on the work of multiple
developers including Matthew Garrett, Chun-Yi Lee, Seth Forshee,
and Aaron Lu.
- Fix from Aaron Lu makes the kernel follow Windows 8 by informing
the firmware through the _DOS method that it should not carry out
automatic brightness changes, so that brightness can be controlled
by GUI"
* tag 'acpi-video-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / video: no automatic brightness changes by win8-compatible firmware
ACPI / video / i915: No ACPI backlight if firmware expects Windows 8
ACPI / video: Always call acpi_video_init_brightness() on init
ACPICA: expose OSI version
Linus Torvalds [Sun, 21 Jul 2013 03:11:42 +0000 (20:11 -0700)]
Merge tag 'ext4_for_linus' of git://git./linux/kernel/git/tytso/ext4
Pull ext[34] tmpfile bugfix from Ted Ts'o:
"Fix regression caused by commit
af51a2ac36d1f which added ->tmpfile()
support (along with a similar fix for ext3)"
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext3: fix a BUG when opening a file with O_TMPFILE flag
ext4: fix a BUG when opening a file with O_TMPFILE flag
Zheng Liu [Sun, 21 Jul 2013 02:03:20 +0000 (22:03 -0400)]
ext3: fix a BUG when opening a file with O_TMPFILE flag
When we try to open a file with O_TMPFILE flag, we will trigger a bug.
The root cause is that in ext4_orphan_add() we check ->i_nlink == 0 and
this check always fails because we set ->i_nlink = 1 in
inode_init_always(). We can use the following program to trigger it:
int main(int argc, char *argv[])
{
int fd;
fd = open(argv[1], O_TMPFILE, 0666);
if (fd < 0) {
perror("open ");
return -1;
}
close(fd);
return 0;
}
The oops message looks like this:
kernel: kernel BUG at fs/ext3/namei.c:1992!
kernel: invalid opcode: 0000 [#1] SMP
kernel: Modules linked in: ext4 jbd2 crc16 cpufreq_ondemand ipv6 dm_mirror dm_region_hash dm_log dm_mod parport_pc parport serio_raw sg dcdbas pcspkr i2c_i801 ehci_pci ehci_hcd button acpi_cpufreq mperf e1000e ptp pps_core ttm drm_kms_helper drm hwmon i2c_algo_bit i2c_core ext3 jbd sd_mod ahci libahci libata scsi_mod uhci_hcd
kernel: CPU: 0 PID: 2882 Comm: tst_tmpfile Not tainted 3.11.0-rc1+ #4
kernel: Hardware name: Dell Inc. OptiPlex 780 /0V4W66, BIOS A05 08/11/2010
kernel: task:
ffff880112d30050 ti:
ffff8801124d4000 task.ti:
ffff8801124d4000
kernel: RIP: 0010:[<
ffffffffa00db5ae>] [<
ffffffffa00db5ae>] ext3_orphan_add+0x6a/0x1eb [ext3]
kernel: RSP: 0018:
ffff8801124d5cc8 EFLAGS:
00010202
kernel: RAX:
0000000000000000 RBX:
ffff880111510128 RCX:
ffff8801114683a0
kernel: RDX:
0000000000000000 RSI:
ffff880111510128 RDI:
ffff88010fcf65a8
kernel: RBP:
ffff8801124d5d18 R08:
0080000000000000 R09:
ffffffffa00d3b7f
kernel: R10:
ffff8801114683a0 R11:
ffff8801032a2558 R12:
0000000000000000
kernel: R13:
ffff88010fcf6800 R14:
ffff8801032a2558 R15:
ffff8801115100d8
kernel: FS:
00007f5d172b5700(0000) GS:
ffff880117c00000(0000) knlGS:
0000000000000000
kernel: CS: 0010 DS: 0000 ES: 0000 CR0:
000000008005003b
kernel: CR2:
00007f5d16df15d0 CR3:
0000000110b1d000 CR4:
00000000000407f0
kernel: Stack:
kernel:
000000000000000c ffff8801048a7dc8 ffff8801114685a8 ffffffffa00b80d7
kernel:
ffff8801124d5e38 ffff8801032a2558 ffff88010ce24d68 0000000000000000
kernel:
ffff88011146b300 ffff8801124d5d44 ffff8801124d5d78 ffffffffa00db7e1
kernel: Call Trace:
kernel: [<
ffffffffa00b80d7>] ? journal_start+0x8c/0xbd [jbd]
kernel: [<
ffffffffa00db7e1>] ext3_tmpfile+0xb2/0x13b [ext3]
kernel: [<
ffffffff821076f8>] path_openat+0x11f/0x5e7
kernel: [<
ffffffff821c86b4>] ? list_del+0x11/0x30
kernel: [<
ffffffff82065fa2>] ? __dequeue_entity+0x33/0x38
kernel: [<
ffffffff82107cd5>] do_filp_open+0x3f/0x8d
kernel: [<
ffffffff82112532>] ? __alloc_fd+0x50/0x102
kernel: [<
ffffffff820f9296>] do_sys_open+0x13b/0x1cd
kernel: [<
ffffffff820f935c>] SyS_open+0x1e/0x20
kernel: [<
ffffffff82398c02>] system_call_fastpath+0x16/0x1b
kernel: Code: 39 c7 0f 85 67 01 00 00 0f b7 03 25 00 f0 00 00 3d 00 40 00 00 74 18 3d 00 80 00 00 74 11 3d 00 a0 00 00 74 0a 83 7b 48 00 74 04 <0f> 0b eb fe 49 8b 85 50 03 00 00 4c 89 f6 48 c7 c7 c0 99 0e a0
kernel: RIP [<
ffffffffa00db5ae>] ext3_orphan_add+0x6a/0x1eb [ext3]
kernel: RSP <
ffff8801124d5cc8>
Here we couldn't call clear_nlink() directly because in d_tmpfile() we
will call inode_dec_link_count() to decrease ->i_nlink. So this commit
tries to call d_tmpfile() before ext4_orphan_add() to fix this problem.
Signed-off-by: Zheng Liu <wenqing.lz@taobao.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: Jan Kara <jack@suse.cz>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Zheng Liu [Sun, 21 Jul 2013 01:58:38 +0000 (21:58 -0400)]
ext4: fix a BUG when opening a file with O_TMPFILE flag
When we try to open a file with O_TMPFILE flag, we will trigger a bug.
The root cause is that in ext4_orphan_add() we check ->i_nlink == 0 and
this check always fails because we set ->i_nlink = 1 in
inode_init_always(). We can use the following program to trigger it:
int main(int argc, char *argv[])
{
int fd;
fd = open(argv[1], O_TMPFILE, 0666);
if (fd < 0) {
perror("open ");
return -1;
}
close(fd);
return 0;
}
The oops message looks like this:
kernel BUG at fs/ext4/namei.c:2572!
invalid opcode: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
Modules linked in: dlci bridge stp hidp cmtp kernelcapi l2tp_ppp l2tp_netlink l2tp_core sctp libcrc32c rfcomm tun fuse nfnetli
nk can_raw ipt_ULOG can_bcm x25 scsi_transport_iscsi ipx p8023 p8022 appletalk phonet psnap vmw_vsock_vmci_transport af_key vmw_vmci rose vsock atm can netrom ax25 af_rxrpc ir
da pppoe pppox ppp_generic slhc bluetooth nfc rfkill rds caif_socket caif crc_ccitt af_802154 llc2 llc snd_hda_codec_realtek snd_hda_intel snd_hda_codec serio_raw snd_pcm pcsp
kr edac_core snd_page_alloc snd_timer snd soundcore r8169 mii sr_mod cdrom pata_atiixp radeon backlight drm_kms_helper ttm
CPU: 1 PID: 1812571 Comm: trinity-child2 Not tainted 3.11.0-rc1+ #12
Hardware name: Gigabyte Technology Co., Ltd. GA-MA78GM-S2H/GA-MA78GM-S2H, BIOS F12a 04/23/2010
task:
ffff88007dfe69a0 ti:
ffff88010f7b6000 task.ti:
ffff88010f7b6000
RIP: 0010:[<
ffffffff8125ce69>] [<
ffffffff8125ce69>] ext4_orphan_add+0x299/0x2b0
RSP: 0018:
ffff88010f7b7cf8 EFLAGS:
00010202
RAX:
0000000000000000 RBX:
ffff8800966d3020 RCX:
0000000000000000
RDX:
0000000000000000 RSI:
ffff88007dfe70b8 RDI:
0000000000000001
RBP:
ffff88010f7b7d40 R08:
ffff880126a3c4e0 R09:
ffff88010f7b7ca0
R10:
0000000000000000 R11:
0000000000000000 R12:
ffff8801271fd668
R13:
ffff8800966d2f78 R14:
ffff88011d7089f0 R15:
ffff88007dfe69a0
FS:
00007f70441a3740(0000) GS:
ffff88012a800000(0000) knlGS:
00000000f77c96c0
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
0000000002834000 CR3:
0000000107964000 CR4:
00000000000007e0
DR0:
0000000000780000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000ffff0ff0 DR7:
0000000000000600
Stack:
0000000000002000 00000020810b6dde 0000000000000000 ffff88011d46db00
ffff8800966d3020 ffff88011d7089f0 ffff88009c7f4c10 ffff88010f7b7f2c
ffff88007dfe69a0 ffff88010f7b7da8 ffffffff8125cfac ffff880100000004
Call Trace:
[<
ffffffff8125cfac>] ext4_tmpfile+0x12c/0x180
[<
ffffffff811cba78>] path_openat+0x238/0x700
[<
ffffffff8100afc4>] ? native_sched_clock+0x24/0x80
[<
ffffffff811cc647>] do_filp_open+0x47/0xa0
[<
ffffffff811db73f>] ? __alloc_fd+0xaf/0x200
[<
ffffffff811ba2e4>] do_sys_open+0x124/0x210
[<
ffffffff81010725>] ? syscall_trace_enter+0x25/0x290
[<
ffffffff811ba3ee>] SyS_open+0x1e/0x20
[<
ffffffff816ca8d4>] tracesys+0xdd/0xe2
[<
ffffffff81001001>] ? start_thread_common.constprop.6+0x1/0xa0
Code: 04 00 00 00 89 04 24 31 c0 e8 c4 77 04 00 e9 43 fe ff ff 66 25 00 d0 66 3d 00 80 0f 84 0e fe ff ff 83 7b 48 00 0f 84 04 fe ff ff <0f> 0b 49 8b 8c 24 50 07 00 00 e9 88 fe ff ff 0f 1f 84 00 00 00
Here we couldn't call clear_nlink() directly because in d_tmpfile() we
will call inode_dec_link_count() to decrease ->i_nlink. So this commit
tries to call d_tmpfile() before ext4_orphan_add() to fix this problem.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Zheng Liu <wenqing.lz@taobao.com>
Tested-by: Darrick J. Wong <darrick.wong@oracle.com>
Tested-by: Dave Jones <davej@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds [Sat, 20 Jul 2013 22:42:38 +0000 (15:42 -0700)]
Merge tag 'staging-3.11-rc2' of git://git./linux/kernel/git/gregkh/staging
Pull staging tree fixes from Greg KH:
"Here are a few iio driver fixes for 3.11-rc2. They are still spread
across drivers/iio and drivers/staging/iio so they are coming in
through this tree.
I've also removed the drivers/staging/csr/ driver as the developers
who originally sent it to me have moved on to other companies, and CSR
still will not send us the specs for the device, making the driver
pretty much obsolete and impossible to fix up. Deleting it now
prevents people from sending in lots of tiny codingsyle fixes that
will never go anywhere.
It also helps to offset the large lustre filesystem merge that
happened in 3.11-rc1 in the overall 3.11.0 diffstat. :)"
* tag 'staging-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: csr: remove driver
iio: lps331ap: Fix wrong in_pressure_scale output value
iio staging: fix lis3l02dq, read error handling
staging:iio:ad7291: add missing .driver_module to struct iio_info
iio: ti_am335x_adc: add missing .driver_module to struct iio_info
iio: mxs-lradc: Remove useless check in read_raw
iio: mxs-lradc: Fix misuse of iio->trig
iio: inkern: fix iio_convert_raw_to_processed_unlocked
iio: Fix iio_channel_has_info
iio:trigger: device_unregister->device_del to avoid double free
iio: dac: ad7303: fix error return code in ad7303_probe()
Linus Torvalds [Sat, 20 Jul 2013 17:50:01 +0000 (10:50 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"The sget() one is a long-standing bug and will need to go into -stable
(in fact, it had been originally caught in RHEL6), the other two are
3.11-only"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vfs: constify dentry parameter in d_count()
livelock avoidance in sget()
allow O_TMPFILE to work with O_WRONLY
Linus Torvalds [Sat, 20 Jul 2013 17:48:59 +0000 (10:48 -0700)]
Merge tag 'ext4_for_linus' of git://git./linux/kernel/git/tytso/ext4
Pull ext4 bugfixes from Ted Ts'o:
"Fixes for 3.11-rc2, sent at 5pm, in the professoinal style. :-)"
I'm not sure I like this new level of "professionalism".
9-5, people, 9-5.
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: call ext4_es_lru_add() after handling cache miss
ext4: yield during large unlinks
ext4: make the extent_status code more robust against ENOMEM failures
ext4: simplify calculation of blocks to free on error
ext4: fix error handling in ext4_ext_truncate()
Linus Torvalds [Sat, 20 Jul 2013 17:48:24 +0000 (10:48 -0700)]
Merge tag 'nfs-for-3.11-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- Fix a regression against NFSv4 FreeBSD servers when creating a new
file
- Fix another regression in rpc_client_register()
* tag 'nfs-for-3.11-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4: Fix a regression against the FreeBSD server
SUNRPC: Fix another issue with rpc_client_register()
Linus Torvalds [Sat, 20 Jul 2013 17:47:38 +0000 (10:47 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/josef/btrfs-next
Pull btrfs fixes from Josef Bacik:
"I'm playing the role of Chris Mason this week while he's on vacation.
There are a few critical fixes for btrfs here, all regressions and
have been tested well"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/josef/btrfs-next:
Btrfs: fix wrong write offset when replacing a device
Btrfs: re-add root to dead root list if we stop dropping it
Btrfs: fix lock leak when resuming snapshot deletion
Btrfs: update drop progress before stopping snapshot dropping
Peng Tao [Thu, 18 Jul 2013 14:09:08 +0000 (22:09 +0800)]
vfs: constify dentry parameter in d_count()
so that it can be used in places like d_compare/d_hash
without causing a compiler warning.
Signed-off-by: Peng Tao <tao.peng@emc.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Fri, 19 Jul 2013 23:13:55 +0000 (03:13 +0400)]
livelock avoidance in sget()
Eric Sandeen has found a nasty livelock in sget() - take a mount(2) about
to fail. The superblock is on ->fs_supers, ->s_umount is held exclusive,
->s_active is 1. Along comes two more processes, trying to mount the same
thing; sget() in each is picking that superblock, bumping ->s_count and
trying to grab ->s_umount. ->s_active is 3 now. Original mount(2)
finally gets to deactivate_locked_super() on failure; ->s_active is 2,
superblock is still ->fs_supers because shutdown will *not* happen until
->s_active hits 0. ->s_umount is dropped and now we have two processes
chasing each other:
s_active = 2, A acquired ->s_umount, B blocked
A sees that the damn thing is stillborn, does deactivate_locked_super()
s_active = 1, A drops ->s_umount, B gets it
A restarts the search and finds the same superblock. And bumps it ->s_active.
s_active = 2, B holds ->s_umount, A blocked on trying to get it
... and we are in the earlier situation with A and B switched places.
The root cause, of course, is that ->s_active should not grow until we'd
got MS_BORN. Then failing ->mount() will have deactivate_locked_super()
shut the damn thing down. Fortunately, it's easy to do - the key point
is that grab_super() is called only for superblocks currently on ->fs_supers,
so it can bump ->s_count and grab ->s_umount first, then check MS_BORN and
bump ->s_active; we must never increment ->s_count for superblocks past
->kill_sb(), but grab_super() is never called for those.
The bug is pretty old; we would've caught it by now, if not for accidental
exclusion between sget() for block filesystems; the things like cgroup or
e.g. mtd-based filesystems don't have anything of that sort, so they get
bitten. The right way to deal with that is obviously to fix sget()...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Fri, 19 Jul 2013 23:11:32 +0000 (03:11 +0400)]
allow O_TMPFILE to work with O_WRONLY
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds [Fri, 19 Jul 2013 22:11:09 +0000 (15:11 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/rw/uml
Pull UML fixes from Richard Weinberger:
"Special thanks goes to Toralf Föster for continuously testing UML and
reporting issues!"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: remove dead code
um: siginfo cleanup
uml: Fix which_tmpdir failure when /dev/shm is a symlink, and in other edge cases
um: Fix wait_stub_done() error handling
um: Mark stub pages mapping with VM_PFNMAP
um: Fix return value of strnlen_user()
Linus Torvalds [Fri, 19 Jul 2013 22:10:01 +0000 (15:10 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"MIPS fixes for 3.11. Half of then is for Netlogic the remainder
touches things across arch/mips.
Nothing really dramatic and by rc1 standards MIPS will be in fairly
good shape with this applied. Tested by building all MIPS defconfigs
of which with this pull request four platforms won't build. And yes,
it boots also on my favorite test systems"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: kvm: Kconfig: Drop HAVE_KVM dependency from VIRTUALIZATION
MIPS: Octeon: Fix DT pruning bug with pip ports
MIPS: KVM: Mark KVM_GUEST (T&E KVM) as BROKEN_ON_SMP
MIPS: tlbex: fix broken build in v3.11-rc1
MIPS: Netlogic: Add XLP PIC irqdomain
MIPS: Netlogic: Fix USB block's coherent DMA mask
MIPS: tlbex: Fix typo in r3000 tlb store handler
MIPS: BMIPS: Fix thinko to release slave TP from reset
MIPS: Delete dead invocation of exception_exit().
Linus Torvalds [Fri, 19 Jul 2013 22:08:53 +0000 (15:08 -0700)]
Merge tag 'arm64-stable' of git://git./linux/kernel/git/cmarinas/linux-aarch64
Pull arm64 fixes from Catalin Marinas:
- Post -rc1 update to the common reboot infrastructure.
- Fixes (user cache maintenance fault handling, !COMPAT compilation,
CPU online and interrupt hanlding).
* tag 'arm64-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
arm64: use common reboot infrastructure
arm64: mm: don't treat user cache maintenance faults as writes
arm64: add '#ifdef CONFIG_COMPAT' for aarch32_break_handler()
arm64: Only enable local interrupts after the CPU is marked online
Linus Torvalds [Fri, 19 Jul 2013 22:08:12 +0000 (15:08 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"An update for the BFP jit to the latest and greatest, two patches to
get kdump working again, the random-abort ptrace extention for
transactional execution, the z90crypt module alias for ap and a tiny
cleanup"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/zcrypt: Alias for new zcrypt device driver base module
s390/kdump: Allow copy_oldmem_page() copy to virtual memory
s390/kdump: Disable mmap for s390
s390/bpf,jit: add pkt_type support
s390/bpf,jit: address randomize and write protect jit code
s390/bpf,jit: use generic jit dumper
s390/bpf,jit: call module_free() from any context
s390/qdio: remove unused variable
s390/ptrace: PTRACE_TE_ABORT_RAND
Stefan Behrens [Thu, 4 Jul 2013 14:14:23 +0000 (16:14 +0200)]
Btrfs: fix wrong write offset when replacing a device
Miao Xie reported the following issue:
The filesystem was corrupted after we did a device replace.
Steps to reproduce:
# mkfs.btrfs -f -m single -d raid10 <device0>..<device3>
# mount <device0> <mnt>
# btrfs replace start -rfB 1 <device4> <mnt>
# umount <mnt>
# btrfsck <device4>
The reason for the issue is that we changed the write offset by mistake,
introduced by commit
625f1c8dc.
We read the data from the source device at first, and then write the
data into the corresponding place of the new device. In order to
implement the "-r" option, the source location is remapped using
btrfs_map_block(). The read takes place on the mapped location, and
the write needs to take place on the unmapped location. Currently
the write is using the mapped location, and this commit changes it
back by undoing the change to the write address that the aforementioned
commit added by mistake.
Reported-by: Miao Xie <miaox@cn.fujitsu.com>
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Josef Bacik [Wed, 17 Jul 2013 23:30:20 +0000 (19:30 -0400)]
Btrfs: re-add root to dead root list if we stop dropping it
If we stop dropping a root for whatever reason we need to add it back to the
dead root list so that we will re-start the dropping next transaction commit.
The other case this happens is if we recover a drop because we will add a root
without adding it to the fs radix tree, so we can leak it's root and commit root
extent buffer, adding this to the dead root list makes this cleanup happen.
Thanks,
Cc: stable@vger.kernel.org
Reported-by: Alex Lyakas <alex.btrfs@zadarastorage.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Josef Bacik [Mon, 15 Jul 2013 16:41:42 +0000 (12:41 -0400)]
Btrfs: fix lock leak when resuming snapshot deletion
We aren't setting path->locks[level] when we resume a snapshot deletion which
means we won't unlock the buffer when we free the path. This causes deadlocks
if we happen to re-allocate the block before we've evicted the extent buffer
from cache. Thanks,
Cc: stable@vger.kernel.org
Reported-by: Alex Lyakas <alex.btrfs@zadarastorage.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Josef Bacik [Mon, 15 Jul 2013 15:57:06 +0000 (11:57 -0400)]
Btrfs: update drop progress before stopping snapshot dropping
Alex pointed out a problem and fix that exists in the drop one snapshot at a
time patch. If we decide we need to exit for whatever reason (umount for
example) we will just exit the snapshot dropping without updating the drop
progress. So the next time we go to resume we will BUG_ON() because we can't
find the extent we left off at because we never updated it. This patch fixes
the problem.
Cc: stable@vger.kernel.org
Reported-by: Alex Lyakas <alex.btrfs@zadarastorage.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Linus Torvalds [Fri, 19 Jul 2013 17:17:12 +0000 (10:17 -0700)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull KVM fix from Paolo Bonzini:
"This single patch fixes a regression caused by one of the
optimizations introduced in 3.11, which is generally visible only on
AMD processors"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: MMU: avoid fast page fault fixing mmio page fault
Linus Torvalds [Fri, 19 Jul 2013 16:59:06 +0000 (09:59 -0700)]
Merge tag 'pm+acpi-3.11-rc2' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These are fixes collected over the last week, most importnatly two
cpufreq reverts fixing regressions introduced in 3.10, an autoseelp
fix preventing systems using it from crashing during shutdown and two
ACPI scan fixes related to hotplug.
Specifics:
- Two cpufreq commits from the 3.10 cycle introduced regressions.
The first of them was buggy (it did way much more than it needed to
do) and the second one attempted to fix an issue introduced by the
first one. Fixes from Srivatsa S Bhat revert both.
- If autosleep triggers during system shutdown and the shutdown
callbacks of some device drivers have been called already, it may
crash the system. Fix from Liu Shuo prevents that from happening
by making try_to_suspend() check system_state.
- The ACPI memory hotplug driver doesn't clear its driver_data on
errors which may cause a NULL poiter dereference to happen later.
Fix from Toshi Kani.
- The ACPI namespace scanning code should not try to attach scan
handlers to device objects that have them already, which may
confuse things quite a bit, and it should rescan the whole
namespace branch starting at the given node after receiving a bus
check notify event even if the device at that particular node has
been discovered already. Fixes from Rafael J Wysocki.
- New ACPI video blacklist entry for a system whose initial backlight
setting from the BIOS doesn't make sense. From Lan Tianyu.
- Garbage string output avoindance for ACPI PNP from Liu Shuo.
- Two Kconfig fixes for issues introduced recently in the s3c24xx
cpufreq driver (when moving the driver to drivers/cpufreq) from
Paul Bolle.
- Trivial comment fix in pm_wakeup.h from Chanwoo Choi"
* tag 'pm+acpi-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / video: ignore BIOS initial backlight value for Fujitsu E753
PNP / ACPI: avoid garbage in resource name
cpufreq: Revert commit
2f7021a8 to fix CPU hotplug regression
cpufreq: s3c24xx: fix "depends on ARM_S3C24XX" in Kconfig
cpufreq: s3c24xx: rename CONFIG_CPU_FREQ_S3C24XX_DEBUGFS
PM / Sleep: Fix comment typo in pm_wakeup.h
PM / Sleep: avoid 'autosleep' in shutdown progress
cpufreq: Revert commit a66b2e to fix suspend/resume regression
ACPI / memhotplug: Fix a stale pointer in error path
ACPI / scan: Always call acpi_bus_scan() for bus check notifications
ACPI / scan: Do not try to attach scan handlers to devices having them
Marc Zyngier [Thu, 11 Jul 2013 11:13:00 +0000 (12:13 +0100)]
arm64: use common reboot infrastructure
Commit
7b6d864b48d9 (reboot: arm: change reboot_mode to use enum
reboot_mode) changed the way reboot is handled on arm, which has a
direct impact on arm64 as we share the reset driver on the VE platform.
The obvious fix is to move arm64 to use the same infrastructure.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
[catalin.marinas@arm.com: removed reboot_mode = REBOOT_HARD default setting]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Will Deacon [Fri, 19 Jul 2013 14:37:12 +0000 (15:37 +0100)]
arm64: mm: don't treat user cache maintenance faults as writes
On arm64, cache maintenance faults appear as data aborts with the CM
bit set in the ESR. The WnR bit, usually used to distinguish between
faulting loads and stores, always reads as 1 and (slightly confusingly)
the instructions are treated as reads by the architecture.
This patch fixes our fault handling code to treat cache maintenance
faults in the same way as loads.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Chen Gang [Mon, 24 Jun 2013 09:27:49 +0000 (10:27 +0100)]
arm64: add '#ifdef CONFIG_COMPAT' for aarch32_break_handler()
If 'COMPAT' not defined, aarch32_break_handler() cannot pass compiling,
and it can work independent with 'COMPAT', so remove dummy definition.
The related error:
arch/arm64/kernel/debug-monitors.c:249:5: error: redefinition of ‘aarch32_break_handler’
In file included from arch/arm64/kernel/debug-monitors.c:29:0:
/root/linux-next/arch/arm64/include/asm/debug-monitors.h:89:12: note: previous definition of ‘aarch32_break_handler’ was here
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Catalin Marinas [Fri, 19 Jul 2013 14:08:15 +0000 (15:08 +0100)]
arm64: Only enable local interrupts after the CPU is marked online
There is a slight chance that (timer) interrupts are triggered before a
secondary CPU has been marked online with implications on softirq thread
affinity.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Kirill Tkhai <tkhai@yandex.ru>
Markos Chandras [Tue, 11 Jun 2013 09:02:33 +0000 (09:02 +0000)]
MIPS: kvm: Kconfig: Drop HAVE_KVM dependency from VIRTUALIZATION
Virtualization does not always need KVM capabilities so drop the
dependency. The KVM symbol already depends on HAVE_KVM.
Fixes the following problem on a randconfig:
warning: (REMOTEPROC && RPMSG) selects VIRTUALIZATION which has unmet direct
dependencies (HAVE_KVM)
warning: (REMOTEPROC && RPMSG) selects VIRTUALIZATION which has unmet
direct dependencies (HAVE_KVM)
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5443/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Richard Weinberger [Fri, 19 Jul 2013 09:35:32 +0000 (11:35 +0200)]
um: remove dead code
"me" is not used.
Signed-off-by: Richard Weinberger <richard@nod.at>
Richard Weinberger [Fri, 19 Jul 2013 09:31:36 +0000 (11:31 +0200)]
um: siginfo cleanup
Currently we use both struct siginfo and siginfo_t.
Let's use struct siginfo internally to avoid ongoing
compiler warning. We are allowed to do so because
struct siginfo and siginfo_t are equivalent.
Signed-off-by: Richard Weinberger <richard@nod.at>
Faidon Liambotis [Thu, 11 Jul 2013 21:08:09 +0000 (21:08 +0000)]
MIPS: Octeon: Fix DT pruning bug with pip ports
During the pruning of the device tree octeon_fdt_pip_iface() is called
for each PIP interface and every port up to the port count is removed
from the device tree. However, the count was set to the return value of
cvmx_helper_interface_enumerate() which doesn't actually return the
count but just returns zero on success. This effectively removed *all*
ports from the tree.
Use cvmx_helper_ports_on_interface() instead to fix this. This
successfully restores the 3 ports of my ERLite-3 and fixes the "kernel
assigns random MAC addresses" issue.
Signed-off-by: Faidon Liambotis <paravoid@debian.org>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5587/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Tristan Schmelcher [Mon, 8 Jul 2013 20:19:49 +0000 (16:19 -0400)]
uml: Fix which_tmpdir failure when /dev/shm is a symlink, and in other edge cases
which_tmpdir did the wrong thing if /dev/shm was a symlink (e.g., to /run/shm),
if there were multiple mounts on top of each other, if the mount(s) were
obscured by a later mount, or if /dev/shm was a prefix of another mount point.
This fixes these cases. Applies to 3.9.6.
Signed-off-by: Tristan Schmelcher <tschmelcher@google.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Richard Weinberger [Fri, 17 May 2013 12:21:01 +0000 (14:21 +0200)]
um: Fix wait_stub_done() error handling
If we die within a stub handler we only way to reliable
kill the (obviously) dying uml guest process is killing
it's host twin on the host side.
Signed-off-by: Richard Weinberger <richard@nod.at>
Richard Weinberger [Sun, 12 May 2013 21:26:03 +0000 (23:26 +0200)]
um: Mark stub pages mapping with VM_PFNMAP
Ensure that a process cannot destroy his stub pages with
using MADV_DONTNEED and friends.
Reported-by: toralf.foerster@gmx.de
Signed-off-by: Richard Weinberger <richard@nod.at>
Richard Weinberger [Sat, 11 May 2013 13:35:32 +0000 (15:35 +0200)]
um: Fix return value of strnlen_user()
In case of an error it must not return -EFAULT.
Return 0 like all other archs do.
Reported-by: toralf.foerster@gmx.de
Signed-off-by: Richard Weinberger <richard@nod.at>
James Hogan [Fri, 12 Jul 2013 10:26:11 +0000 (10:26 +0000)]
MIPS: KVM: Mark KVM_GUEST (T&E KVM) as BROKEN_ON_SMP
Make KVM_GUEST depend on BROKEN_ON_SMP so that it cannot be enabled with
SMP.
SMP kernels use ll/sc instructions for an atomic section in the tlb fill
handler, with a tlbp instruction contained in the middle. This cannot be
emulated with trap & emulate KVM because the tlbp instruction traps and
the eret to return to the guest code clears the LLbit which makes the sc
instruction always fail.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Sanjay Lal <sanjayl@kymasys.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/5588/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Aaro Koskinen [Mon, 15 Jul 2013 07:21:57 +0000 (07:21 +0000)]
MIPS: tlbex: fix broken build in v3.11-rc1
Commit
6ba045f9fbdafb48da42aa8576ea7a3980443136 (MIPS: Move generated code
to .text for microMIPS) deleted tlbmiss_handler_setup_pgd_array, but some
references were not converted. Fix that to enable building a MIPS kernel.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Jayachandran C. <jchandra@broadcom.com>
Acked-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5589/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Jayachandran C [Wed, 17 Jul 2013 10:27:26 +0000 (10:27 +0000)]
MIPS: Netlogic: Add XLP PIC irqdomain
Add a legacy irq domain for the XLP PIC interrupts. This will be used
when interrupts are assigned from the device tree. This change is required
after commit c5cdc67 "irqdomain: Remove temporary MIPS workaround code".
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Cc: Jayachandran C <jchandra@broadcom.com>
Patchwork: https://patchwork.linux-mips.org/patch/5597/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ganesan Ramalingam [Wed, 17 Jul 2013 10:27:25 +0000 (10:27 +0000)]
MIPS: Netlogic: Fix USB block's coherent DMA mask
The on-chip USB controller on Netlogic XLP does not suppport
DMA beyond 32-bit physical address. Set the coherent_dma_mask
of the USB in its PCI fixup to support this.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C. <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5596/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Tony Wu [Thu, 18 Jul 2013 09:45:47 +0000 (09:45 +0000)]
MIPS: tlbex: Fix typo in r3000 tlb store handler
commit 6ba045f (MIPS: Move generated code to .text for microMIPS)
causes a panic at boot. The handler builder should test against
handle_tlbs_end, not handle_tlbs.
Signed-off-by: Tony Wu <tung7970@gmail.com>
Acked-by: Jayachandran C. <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5600/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>