Phil Elwell [Thu, 7 Feb 2019 18:16:25 +0000 (18:16 +0000)]
configs: Enable the AD193x codecs
See: https://github.com/raspberrypi/linux/issues/2850
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
HiFiBerry [Mon, 8 Oct 2018 16:10:12 +0000 (18:10 +0200)]
Added driver for the HiFiBerry DAC+ ADC (#2694)
Signed-off-by: Daniel Matuschek <daniel@hifiberry.com>
hifiberry_dacplusadc: switch to snd_soc_dai_set_bclk_ratio
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplusadc: fix DAI link setup
The driver only defines a single DAI link and the code that tries
to setup the second (non-existent) DAI link looks wrong - using dmic
as a CPU/platform driver doesn't make any sense.
The DT overlay doesn't define a dmic property, so the code was never
executed (otherwise it would have resulted in a memory corruption).
So drop the offending code to prevent issues if a dmic property
should be added to the DT overlay.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplusadc: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
Phil Elwell [Tue, 15 Jan 2019 12:41:15 +0000 (12:41 +0000)]
spi: spi-bcm2835: Disable forced software CS
With GPIO CS used by the DTBs, allow hardware CS to be selected by an
overlay.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Tue, 15 Jan 2019 12:39:50 +0000 (12:39 +0000)]
spi: spi-bcm2835: Re-enable HW CS
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
b-ak [Wed, 2 Jan 2019 18:31:08 +0000 (00:01 +0530)]
ASoC: Add support for AudioSense-Pi add-on soundcard
AudioSense-Pi is a RPi HAT based on a TI's TLV320AIC32x4 stereo codec
This hardware provides multiple audio I/O capabilities to the RPi.
The codec connects to the RPi's SoC through the I2S Bus.
The following devices can be connected through a 3.5mm jack
1. Line-In: Plain old audio in from mobile phones, PCs, etc.,
2. Mic-In: Connect a microphone
3. Line-Out: Connect the output to a speaker
4. Headphones: Connect a Headphone w or w/o microphones
Multiple Inputs:
It supports the following combinations
1. Two stereo Line-Inputs and a microphone
2. One stereo Line-Input and two microphones
3. Two stereo Line-Inputs, a microphone and
one mono line-input (with h/w hack)
4. One stereo Line-Input, two microphones and
one mono line-input (with h/w hack)
Multiple Outputs:
Audio output can be routed to the headphones or
speakers (with additional hardware)
Signed-off-by: b-ak <anur.bhargav@gmail.com>
ASoC: audiosense-pi: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Joshua Emele [Thu, 8 Nov 2018 00:07:40 +0000 (16:07 -0800)]
lan78xx: Debounce link events to minimize poll storm
The bInterval is set to 4 (i.e. 8 microframes => 1ms) and the only bit
that the driver pays attention to is "link was reset". If there's a
flapping status bit in that endpoint data, (such as if PHY negotiation
needs a few tries to get a stable link) then polling at a slower rate
would act as a de-bounce.
See: https://github.com/raspberrypi/linux/issues/2447
Dave Stevenson [Thu, 10 Jan 2019 17:58:06 +0000 (17:58 +0000)]
firmware: raspberrypi: Report the fw variant during probe
The driver already reported the firmware build date during probe.
The mailbox calls have been extended to also report the variant
1 = standard start.elf
2 = start_x.elf (includes camera stack)
3 = start_db.elf (includes assert logging)
4 = start_cd.elf (cutdown version for smallest memory footprint).
Log the variant during probe.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
firmware: raspberrypi: Report the fw git hash during probe
The firmware can now report the git hash from which it was built
via the mailbox, so report it during probe.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Mon, 29 Oct 2018 14:21:04 +0000 (14:21 +0000)]
staging: bcm2835-camera: Ensure H264 header bytes get a sensible timestamp
H264 header come from VC with 0 timestamps, which means they get a
strange timestamp when processed with VC/kernel start times,
particularly if used with the inline header option.
Remember the last frame timestamp and use that if set, or otherwise
use the kernel start time.
https://github.com/raspberrypi/linux/issues/1836
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Phil Elwell [Mon, 26 Nov 2018 19:46:58 +0000 (19:46 +0000)]
net: lan78xx: Support auto-downshift to 100Mb/s
Ethernet cables with faulty or missing pairs (specifically pairs C and
D) allow auto-negotiation to 1000Mbs, but do not support the successful
establishment of a link. Add a DT property, "microchip,downshift-after",
to configure the number of auto-negotiation failures after which it
falls back to 100Mbs. Valid values are 2, 3, 4, 5 and 0, where 0 means
never downshift.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Tue, 24 Apr 2018 13:42:27 +0000 (14:42 +0100)]
gpiolib: Don't prevent IRQ usage of output GPIOs
Upstream Linux deems using output GPIOs to generate IRQs as a bogus
use case, even though the BCM2835 GPIO controller is capable of doing
so. A number of users would like to make use of this facility, so
disable the checks.
See: https://github.com/raspberrypi/linux/issues/2527
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
James Hughes [Fri, 2 Nov 2018 11:55:49 +0000 (11:55 +0000)]
Update issue templates (#2736)
Serge Schneider [Tue, 2 Oct 2018 10:14:15 +0000 (11:14 +0100)]
drivers: thermal: step_wise: avoid throttling at hysteresis temperature after dropping below it
Signed-off-by: Serge Schneider <serge@raspberrypi.org>
Ram Chandrasekar [Mon, 7 May 2018 17:54:08 +0000 (11:54 -0600)]
drivers: thermal: step_wise: add support for hysteresis
Step wise governor increases the mitigation level when the temperature
goes above a threshold and will decrease the mitigation when the
temperature falls below the threshold. If it were a case, where the
temperature hovers around a threshold, the mitigation will be applied
and removed at every iteration. This reaction to the temperature is
inefficient for performance.
The use of hysteresis temperature could avoid this ping-pong of
mitigation by relaxing the mitigation to happen only when the
temperature goes below this lower hysteresis value.
Signed-off-by: Ram Chandrasekar <rkumbako@codeaurora.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Phil Elwell [Tue, 6 Nov 2018 12:57:48 +0000 (12:57 +0000)]
sc16is7xx: Don't spin if no data received
See: https://github.com/raspberrypi/linux/issues/2676
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Stefan Wahren [Sat, 13 Oct 2018 11:31:21 +0000 (13:31 +0200)]
firmware: raspberrypi: Add backward compatible get_throttled
Avoid a hard userspace ABI change by adding a compatible get_throttled
sysfs entry. Its value is now feed by the GET_THROTTLED requests of the
new hwmon driver. The first access to get_throttled will generate
a warning.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Stefan Wahren [Sat, 6 Oct 2018 14:46:18 +0000 (16:46 +0200)]
hwmon: raspberrypi: Prevent voltage low warnings from filling log
Although the correct fix for low voltage warnings is to
improve the power supply, the current implementation
of the detection can fill the log if the warning
happens freqently. This replaces the logging with
slightly custom ratelimited logging.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
detule [Tue, 2 Oct 2018 08:10:08 +0000 (04:10 -0400)]
vchiq_2835_arm: Implement a DMA pool for small bulk transfers (#2699)
During a bulk transfer we request a DMA allocation to hold the
scatter-gather list. Most of the time, this allocation is small
(<< PAGE_SIZE), however it can be requested at a high enough frequency
to cause fragmentation and/or stress the CMA allocator (think time
spent in compaction here, or during allocations elsewhere).
Implement a pool to serve up small DMA allocations, falling back
to a coherent allocation if the request is greater than
VCHIQ_DMA_POOL_SIZE.
Signed-off-by: Oliver Gjoneski <ogjoneski@gmail.com>
popcornmix [Mon, 17 Sep 2018 16:31:18 +0000 (17:31 +0100)]
cxd2880: CXD2880_SPI_DRV should select DVB_CXD2880 with MEDIA_SUBDRV_AUTOSELECT
Serge Schneider [Mon, 9 Jul 2018 11:54:25 +0000 (12:54 +0100)]
Add rpi-poe-fan driver
Signed-off-by: Serge Schneider <serge@raspberrypi.org>
PoE HAT driver cleanup
* Fix undeclared variable in rpi_poe_fan_suspend
* Add SPDX-License-Identifier
* Expand PoE acronym in Kconfig help
* Give clearer error message on of_property_count_u32_elems fail
* Add documentation
* Add vendor to of_device_id compatible string.
* Rename m_data_s struct to fw_data_s
* Fix typos
Fixes: #2665
Signed-off-by: Serge Schneider <serge@raspberrypi.org>
Phil Elwell [Thu, 5 Apr 2018 13:46:11 +0000 (14:46 +0100)]
lan78xx: Move enabling of EEE into PHY init code
Enable EEE mode as soon as possible after connecting to the PHY, and
before phy_start. This avoids a second link negotiation, which speeds
up booting and stops the interface failing to become ready.
See: https://github.com/raspberrypi/linux/issues/2437
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Wed, 20 Jun 2018 11:20:01 +0000 (12:20 +0100)]
brcmfmac: Re-enable firmware roaming support
As of 4.18, a firmware that implements the update_connect_params
method but doesn't claim to support roaming causes an error. We
disabled firmware roaming in 4.4 [1] because it appeared to
prevent disconnects, but let's try with the current firmware to see
if things have improved.
[1] https://github.com/raspberrypi/linux/commit/
dd9188011786fb62a7960922f31e8e086fb2009b
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Dave Stevenson [Wed, 13 Jun 2018 14:21:10 +0000 (15:21 +0100)]
net: lan78xx: Disable TCP Segmentation Offload (TSO)
TSO seems to be having issues when packets are dropped and the
remote end uses Selective Acknowledge (SACK) to denote that
data is missing. The missing data is never resent, so the
connection eventually stalls.
There is a module parameter of enable_tso added to allow
further debugging without forcing a rebuild of the kernel.
https://github.com/raspberrypi/linux/issues/2449
https://github.com/raspberrypi/linux/issues/2482
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Phil Elwell [Thu, 14 Jun 2018 14:07:26 +0000 (15:07 +0100)]
of: configfs: Use of_overlay_fdt_apply API call
The published API to the dynamic overlay application mechanism now
takes a Flattened Device Tree blob as input so that it can manage the
lifetime of the unflattened tree. Conveniently, the new API call -
of_overlay_fdt_apply - is virtually a drop-in replacement for
create_overlay, which can now be deleted.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Thu, 14 Jun 2018 10:21:04 +0000 (11:21 +0100)]
irqchip: irq-bcm2835: Calc. FIQ_START at boot-time
ad83c7cb2f37 ("irqchip/irq-bcm2836: Add support for DT interrupt polarity")
changed the way that the BCM2836/7 local interrupts are mapped; instead
of being pre-mapped they are now mapped on-demand. A side effect of this
change is that the call to irq_of_parse_and_map from armctrl_of_init
creates a new mapping, forming a gap between the IRQs and the FIQs. This
gap breaks the FIQ<->IRQ mapping which up to now has been done by assuming:
1) that the value of FIQ_START is the same as the number of normal IRQs
that will be mapped (still true), and
2) that this value is also the offset between an IRQ and its equivalent
FIQ (which is no longer the case).
Remove both assumptions by measuring the interval between the last IRQ
and the last FIQ, passing it as the parameter to init_FIQ().
Fixes: https://github.com/raspberrypi/linux/issues/2432
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Sat, 12 May 2018 20:35:43 +0000 (21:35 +0100)]
firmware/raspberrypi: Notify firmware of a reboot
Register for reboot notifications, sending RPI_FIRMWARE_NOTIFY_REBOOT
over the mailbox interface on reception.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Nick Bulleid [Thu, 10 May 2018 20:57:02 +0000 (21:57 +0100)]
Add ability to export gpio used by gpio-poweroff
Signed-off-by: Nick Bulleid <nedbulleid@fastmail.com>
Added export feature to gpio-poweroff documentation
Signed-off-by: Nick Bulleid <nedbulleid@fastmail.com>
popcornmix [Mon, 14 Jul 2014 21:02:09 +0000 (22:02 +0100)]
hid: Reduce default mouse polling interval to 60Hz
Reduces overhead when using X
Phil Elwell [Fri, 9 Mar 2018 12:01:00 +0000 (12:01 +0000)]
lan78xx: Read initial EEE status from DT
Add two new DT properties:
* microchip,eee-enabled - a boolean to enable EEE
* microchip,tx-lpi-timer - time in microseconds to wait before entering
low power state
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
hdoverobinson [Tue, 13 Mar 2018 10:58:39 +0000 (06:58 -0400)]
added capture_clear option to pps-gpio via dtoverlay (#2433)
Phil Elwell [Tue, 20 Feb 2018 10:07:27 +0000 (10:07 +0000)]
i2c-gpio: Also set bus numbers from reg property
I2C busses can be assigned specific bus numbers using aliases in
Device Tree - string properties where the name is the alias and the
value is the path to the node. The current DT parameter mechanism
does not allow property names to be derived from a parameter value
in any way, so it isn't possible to generate unique or matching
aliases for nodes from an overlay that can generate multiple
instances, e.g. i2c-gpio.
Work around this limitation (at least temporarily) by allowing
the i2c adapter number to be initialised from the "reg" property
if present.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Eric Anholt [Mon, 5 Feb 2018 18:53:18 +0000 (18:53 +0000)]
drm/vc4: Don't wait for vblank on fkms cursor updates.
We don't use the same async update path between fkms and normal kms,
and the normal kms workaround ended up making us wait. This became a
larger problem in rpi-4.14.y, as the USB HID update rate throttling
got (accidentally?) dropped.
Signed-off-by: Eric Anholt <eric@anholt.net>
Dave Stevenson [Tue, 19 Feb 2019 15:06:31 +0000 (15:06 +0000)]
gpu:vc4-fkms: Update driver to not use plane->crtc.
Following on from
commit
2f958af7fc248 ("drm/vc4: Stop updating plane->fb/crtc")
do the same in the firmwarekms driver and look at plane_state->crtc
instead.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
popcornmix [Sun, 17 Jun 2018 12:22:07 +0000 (13:22 +0100)]
vc4_firmware_kms: fix build
Eric Anholt [Mon, 5 Feb 2018 18:22:03 +0000 (18:22 +0000)]
drm/vc4: Remove duplicate primary/cursor fields from FKMS driver.
The CRTC has those fields and we can just use them.
Signed-off-by: Eric Anholt <eric@anholt.net>
Eric Anholt [Mon, 5 Feb 2018 18:02:30 +0000 (18:02 +0000)]
drm/vc4: Skip SET_CURSOR_INFO when the cursor contents didn't change.
Signed-off-by: Eric Anholt <eric@anholt.net>
Eric Anholt [Mon, 5 Feb 2018 18:01:02 +0000 (18:01 +0000)]
drm/vc4: Fix warning about vblank interrupts before DRM core is ready.
The SMICS interrupt fires continuously, but since it's 1/100 the rate
of the USB interrupts, we don't really need a way to turn it off. We
do need to make sure that we don't tell DRM about it until DRM has
asked for the interrupt at least once, because otherwise it will throw
a warning at boot time.
Signed-off-by: Eric Anholt <eric@anholt.net>
popcornmix [Tue, 18 Apr 2017 20:43:46 +0000 (21:43 +0100)]
vc4_fkms: Apply firmware overscan offset to hardware cursor
Eric Anholt [Tue, 30 Jan 2018 22:21:02 +0000 (14:21 -0800)]
drm/vc4: Add missing enable/disable vblank handlers in fkms.
Fixes hang at boot in 4.14.
Signed-off-by: Eric Anholt <eric@anholt.net>
Eric Anholt [Wed, 7 Jun 2017 21:39:49 +0000 (14:39 -0700)]
drm/vc4: Add FB modifier support to firmwarekms.
Signed-off-by: Eric Anholt <eric@anholt.net>
(cherry picked from commit
11752d73488e08aaeb65fe8289a9c016acde26c2)
Eric Anholt [Thu, 6 Jul 2017 18:45:48 +0000 (11:45 -0700)]
drm/vc4: Add support for setting DPMS in firmwarekms.
This ensures that the screen goes blank during DPMS (screensaver),
including the cursor. Planes don't necessarily get disabled during
CRTC disable, so we need to be careful to not leave them on or turn
them back on early.
Signed-off-by: Eric Anholt <eric@anholt.net>
Eric Anholt [Thu, 2 Feb 2017 17:42:18 +0000 (09:42 -0800)]
drm/vc4: Fix sending of page flip completion events in FKMS mode.
In the rewrite of vc4_crtc.c for fkms, I dropped the part of the
CRTC's atomic flush handler that moved the completion event from the
proposed atomic state change to the CRTC's current state. That meant
that when full screen pageflipping happened (glxgears -fullscreen in
X, compton, por weston), the app would end up blocked firever waiting
to draw its next frame.
Signed-off-by: Eric Anholt <eric@anholt.net>
Eric Anholt [Thu, 2 Feb 2017 01:10:09 +0000 (17:10 -0800)]
drm/vc4: Add DRM_DEBUG_ATOMIC for the insides of fkms.
Trying to debug weston on fkms involved figuring out what calls I was
making to the firmware.
Signed-off-by: Eric Anholt <eric@anholt.net>
Eric Anholt [Thu, 2 Feb 2017 01:09:18 +0000 (17:09 -0800)]
drm/vc4: Name the primary and cursor planes in fkms.
This makes debugging nicer, compared to trying to remember what the
IDs are.
Signed-off-by: Eric Anholt <eric@anholt.net>
Eric Anholt [Wed, 14 Sep 2016 07:39:33 +0000 (08:39 +0100)]
drm/vc4: Add a mode for using the closed firmware for display.
Signed-off-by: Eric Anholt <eric@anholt.net>
Eric Anholt [Wed, 14 Sep 2016 08:16:19 +0000 (09:16 +0100)]
raspberrypi-firmware: Export the general transaction function.
The vc4-firmware-kms module is going to be doing the MBOX FB call.
Signed-off-by: Eric Anholt <eric@anholt.net>
Phil Elwell [Mon, 22 Jan 2018 17:26:38 +0000 (17:26 +0000)]
serial: 8250: bcm2835aux - suppress EPROBE_DEFER
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Mon, 11 Dec 2017 09:18:32 +0000 (09:18 +0000)]
ARM: Activate FIQs to avoid __irq_startup warnings
There is a new test in __irq_startup that the IRQ is activated, which
hasn't been the case for FIQs since they bypass some of the usual setup.
Augment enable_fiq to include a call to irq_activate to avoid the
warning.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Mon, 16 Jul 2018 13:40:13 +0000 (14:40 +0100)]
dwc-otg: FIQ: Fix "bad mode in data abort handler"
Create a semi-static mapping for the USB registers early in the boot
process, before additional kernel threads are started, so all threads
will have the mappings from the start. This avoids the need for
data aborts to lazily update them.
See: https://github.com/raspberrypi/linux/issues/2450
Signed-off-by: Floris Bos <bos@je-eigen-domein.nl>
Noralf Trønnes [Wed, 3 Jun 2015 10:26:13 +0000 (12:26 +0200)]
ARM: bcm2835: Set Serial number and Revision
The VideoCore bootloader passes in Serial number and
Revision number through Device Tree. Make these available to
userspace through /proc/cpuinfo.
Mainline status:
There is a commit in linux-next that standardize passing the serial
number through Device Tree (string: /serial-number):
ARM: 8355/1: arch: Show the serial number from devicetree in cpuinfo
There was an attempt to do the same with the revision number, but it
didn't get in:
[PATCH v2 1/2] arm: devtree: Set system_rev from DT revision
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Phil Elwell [Mon, 27 Nov 2017 17:14:54 +0000 (17:14 +0000)]
cgroup: Disable cgroup "memory" by default
Some Raspberry Pis have limited RAM and most users won't use the
cgroup memory support so it is disabled by default. Enable with:
cgroup_enable=memory
See: https://github.com/raspberrypi/linux/issues/1950
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
James Hughes [Tue, 14 Nov 2017 15:13:15 +0000 (15:13 +0000)]
AXI performance monitor driver (#2222)
Uses the debugfs I/F to provide access to the AXI
bus performance monitors.
Requires the new mailbox peripheral access for access
to the VPU performance registers, system bus access
is done using direct register reads.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
raspberrypi_axi_monitor: suppress warning
Suppress the following warning by casting the pointer to and uintptr_t
before to u32:
Signed-off-by: Matteo Croce <mcroce@redhat.com>
popcornmix [Fri, 25 Aug 2017 18:18:13 +0000 (19:18 +0100)]
cache: export clean and invalidate
hack: cache: Fix linker error
Phil Elwell [Mon, 26 Nov 2018 21:01:18 +0000 (21:01 +0000)]
Revert "build/arm64: Add rules for .dtbo files for dts overlays"
DT build rules are now in the common top-level Makefile.
This reverts commit
dce5b0fbdd2174f7fc9b27f4e89877a33169239a.
Khem Raj [Sat, 11 Feb 2017 01:57:08 +0000 (17:57 -0800)]
build/arm64: Add rules for .dtbo files for dts overlays
We now create overlays as .dtbo files.
Signed-off-by: Khem Raj <raj.khem@gmail.com>
Michael Zoran [Sat, 11 Feb 2017 09:18:31 +0000 (01:18 -0800)]
ARM64: Force hardware emulation of deprecated instructions.
Michael Zoran [Sun, 15 Jan 2017 05:43:57 +0000 (21:43 -0800)]
ARM64: Round-Robin dispatch IRQs between CPUs.
IRQ-CPU mapping is round robined on ARM64 to increase
concurrency and allow multiple interrupts to be serviced
at a time. This reduces the need for FIQ.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
popcornmix [Mon, 13 Apr 2015 16:16:29 +0000 (17:16 +0100)]
config: Add default configs
Phil Elwell [Thu, 17 Dec 2015 13:37:07 +0000 (13:37 +0000)]
hci_h5: Don't send conf_req when ACTIVE
Without this patch, a modem and kernel can continuously bombard each
other with conf_req and conf_rsp messages, in a demented game of tag.
Cheong2K [Fri, 26 Feb 2016 10:20:10 +0000 (18:20 +0800)]
brcm: adds support for BCM43341 wifi
brcmfmac: Disable power management
Disable wireless power saving in the brcmfmac WLAN driver. This is a
temporary measure until the connectivity loss resulting from power
saving is resolved.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
brcmfmac: Use original country code as a fallback
Commit
73345fd212980d2e28a5c6d83801c903bd773680:
brcmfmac: Configure country code using device specific settings
prevents region codes from working on devices that lack a region code
translation table. In the event of an absent table, preserve the old
behaviour of using the provided code as-is.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
brcmfmac: Plug memory leak in brcmf_fill_bss_param
See: https://github.com/raspberrypi/linux/issues/1471
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
brcmfmac: do not use internal roaming engine by default
Some evidence of curing disconnects with this disabled, so make it a default.
Can be overridden with module parameter roamoff=0
See: http://projectable.me/optimize-my-pi-wi-fi/
brcmfmac: Change stop_ap sequence
Patch from Broadcom/Cypress to resolve a customer error
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Pantelis Antoniou [Wed, 3 Dec 2014 11:23:28 +0000 (13:23 +0200)]
OF: DT-Overlay configfs interface
This is a port of Pantelis Antoniou's v3 port that makes use of the
new upstreamed configfs support for binary attributes.
Original commit message:
Add a runtime interface to using configfs for generic device tree overlay
usage. With it its possible to use device tree overlays without having
to use a per-platform overlay manager.
Please see Documentation/devicetree/configfs-overlays.txt for more info.
Changes since v2:
- Removed ifdef CONFIG_OF_OVERLAY (since for now it's required)
- Created a documentation entry
- Slight rewording in Kconfig
Changes since v1:
- of_resolve() -> of_resolve_phandles().
Originally-signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
DT configfs: Fix build errors on other platforms
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
DT configfs: fix build error
There is an error when compiling rpi-4.6.y branch:
CC drivers/of/configfs.o
drivers/of/configfs.c:291:21: error: initialization from incompatible pointer type [-Werror=incompatible-pointer-types]
.default_groups = of_cfs_def_groups,
^
drivers/of/configfs.c:291:21: note: (near initialization for 'of_cfs_subsys.su_group.default_groups.next')
The .default_groups is linked list since commit
1ae1602de028acaa42a0f6ff18d19756f8e825c6.
This commit uses configfs_add_default_group to fix this problem.
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
configfs: New of_overlay API
popcornmix [Mon, 3 Sep 2012 16:10:23 +0000 (17:10 +0100)]
net: Add non-mainline source for rtl8192cu wlan
We are now syncing with version from:
https://github.com/pvaret/rtl8192cu-fixes
popcornmix [Tue, 23 Feb 2016 19:56:04 +0000 (19:56 +0000)]
bcm2835-virtgpio: Virtual GPIO driver
Add a virtual GPIO driver that uses the firmware mailbox interface to
request that the VPU toggles LEDs.
P33M [Wed, 21 Oct 2015 13:55:21 +0000 (14:55 +0100)]
rpi_display: add backlight driver and overlay
Add a mailbox-driven backlight controller for the Raspberry Pi DSI
touchscreen display. Requires updated GPU firmware to recognise the
mailbox request.
Signed-off-by: Gordon Hollingworth <gordon@raspberrypi.org>
Add Raspberry Pi firmware driver to the dependencies of backlight driver
Otherwise the backlight driver fails to build if the firmware
loading driver is not in the kernel
Signed-off-by: Alex Riesen <alexander.riesen@cetitec.com>
Tim Gover [Sat, 21 Jul 2018 19:07:46 +0000 (20:07 +0100)]
ASoC: Create a generic Pi Hat WM8804 driver
Reduce the amount of duplicated code by creating a generic driver for
Pi Hat digi cards using the WM8804 codec.
This replaces the
Allo DigiOne, Hifiberry Digi/Pro, JustBoom Digi and IQAudIO Digi
dedicate soundcard drivers with a generic driver.
There are no significant changes to the runtime behavior of the drivers
and end users should not have to change any configuration settings
after upgrading.
Minor changes
* Check the return value of snd_soc_component_update_bits
* Added some pr_debug tracing
* Various checkpatch tidyups
* Updated allodigi-one to use use 128FS at > 96 Khz. This appears to
be an omission in the original driver code so followed the Hifiberry
DAC driver approach.
ASoC: rpi-wm8804-soundcard: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
rpi-wm8804-soundcard: drop PWRDN register writes
Since kernel 4.0 the PWRDN register bits are under DAPM
control from the wm8804 driver.
Drop code that modifies that register to avoid interfering
with DAPM.
Signed-off-by: Matthias Reichl <hias@horus.com>
rpi-wm8804-soundcard: configure wm8804 clocks only on rate change
This should avoid clicks when stopping and immediately afterwards
starting a stream with the same samplerate as before.
Signed-off-by: Matthias Reichl <hias@horus.com>
rpi-wm8804-soundcard: Fixed MCLKDIV for Allo Digione
The Allo Digione board wants a fixed MCLKDIV of 256.
See: https://github.com/raspberrypi/linux/issues/3296
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
popcornmix [Mon, 3 Sep 2018 16:00:36 +0000 (17:00 +0100)]
ASoC: Add Kconfig and Makefile for sound/soc/bcm
Signed-off-by: popcornmix <popcornmix@gmail.com>
Tim Gover [Wed, 27 Jun 2018 14:59:12 +0000 (15:59 +0100)]
ASoC: Add generic RPI driver for simple soundcards.
The RPI simple sound card driver provides a generic ALSA SOC card driver
supporting a variety of Pi HAT soundcards. The intention is to avoid
the duplication of code for cards that can't be fully supported by
the soc simple/graph cards but are otherwise almost identical.
This initial commit adds support for the ADAU1977 ADC, Google VoiceHat,
HifiBerry AMP, HifiBerry DAC and RPI DAC.
Signed-off-by: Tim Gover <tim.gover@raspberrypi.org>
ASoC: Use correct card name in rpi-simple driver
Use the specific card name from drvdata instead of the snd_rpi_simple
rpi-simple-soundcard: Use nicer driver name "RPi-simple"
Rename the driver from "RPI simple soundcard" to "RPi-simple" so that
the driver name won't be mangled allowing to be used unaltered as the
card conf filename.
ASoC: rpi-simple-soundcard: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
allocom [Thu, 19 Apr 2018 06:42:26 +0000 (12:12 +0530)]
Driver and overlay for Allo Katana DAC
Allo Katana DAC: Updated default values
Signed-off-by: Jaikumar <jaikumar@cem-solutions.com>
Added mute stream func
Signed-off-by: Jaikumar <jaikumar@cem-solutions.net>
codecs: Correct Katana minimum volume
Update Katana minimum volume to get the exact 0.5 dB value in each step.
Signed-off-by: Sudeep Kumar <sudeepkumar@cem-solutions.net>
Peter Malkin [Mon, 27 Mar 2017 23:38:21 +0000 (16:38 -0700)]
Driver support for Google voiceHAT soundcard.
ASoC: googlevoicehat-codec: Use correct device when grabbing GPIO
The fixup for the VoiceHAT in 4.18 incorrectly tried to find the
sdmode GPIO pin under the card device, not the codec device.
This failed, and therefore caused the device probe to fail.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
ASoC: googlevoicehat-codec: Reformat for kernel coding standards
Fix all whitespace, indentation, and bracing errors.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
ASoC: googlevoicehat-codec: Make driver function structure const
Make voicehat_component_driver a const structure.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
ASoC: googlevoicehat-codec: Only convert from ms to jiffies once
Minor optimisation and allows to become checkpatch clean.
A msec value is read out of DT or from a define, and convert once to
jiffies, rather than every time that it is used.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Matt Flax [Wed, 8 Mar 2017 09:04:13 +0000 (20:04 +1100)]
Add support for the AudioInjector.net Octo sound card
AudioInjector Octo: sample rates, regulators, reset
This patch adds new sample rates to the Audioinjector Octo sound card. The
new supported rates are (in kHz) :
96, 48, 32, 24, 16, 8, 88.2, 44.1, 29.4, 22.05, 14.7
Reference the bcm270x DT regulators in the overlay.
This patch adds a reset GPIO for the AudioInjector.net octo sound card.
Audioinjector octo : Make the playback and capture symmetric
This patch ensures that the sample rate and channel count of the audioinjector
octo sound card are symmetric.
audioinjector-octo: Add continuous clock feature
By user request, add a switch to prevent the clocks being stopped when
the stream is paused, stopped or shutdown. Provide access to the switch
by adding a 'non-stop-clocks' parameter to the audioinjector-addons
overlay.
See: https://github.com/raspberrypi/linux/issues/2409
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
sound: Fixes for audioinjector-octo under 4.19
1. Move the DT alias declaration to the I2C shim in the cases
where the shim is enabled. This works around a problem caused by a
4.19 commit [1] that generates DT/OF uevents for I2C drivers.
2. Fix the diagnostics in an error path of the soundcard driver to
correctly identify the reason for the failure to load.
3. Move the declaration of the clock node in the overlay outside
the I2C node to avoid warnings.
4. Sort the overlay nodes so that dependencies are only to earlier
fragments, in an attempt to get runtime dtoverlay application to
work (it still doesn't...)
See: https://github.com/Audio-Injector/Octo/issues/14
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
[1]
af503716ac14 ("i2c: core: report OF style module alias for devices registered via OF")
ASoC: audioinjector-octo-soundcard: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Fe-Pi [Wed, 1 Mar 2017 11:42:43 +0000 (04:42 -0700)]
Add support for Fe-Pi audio sound card. (#1867)
Fe-Pi Audio Sound Card is based on NXP SGTL5000 codec.
Mechanical specification of the board is the same the Raspberry Pi Zero.
3.5mm jacks for Headphone/Mic, Line In, and Line Out.
Signed-off-by: Henry Kupis <fe-pi@cox.net>
ASoC: fe-pi-audio: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Miquel [Fri, 24 Feb 2017 19:51:06 +0000 (20:51 +0100)]
sound: Support for Dion Audio LOCO-V2 DAC-AMP HAT
Signed-off-by: Miquel Blauw <info@dionaudio.nl>
ASoC: dionaudio_loco-v2: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Also remove hw_params and ops as they are no longer needed.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: dionaudio_loco-v2: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Matthias Reichl [Sun, 22 Jan 2017 11:49:37 +0000 (12:49 +0100)]
ASoC: Add driver for Cirrus Logic Audio Card
Note: due to problems with deferred probing of regulators
the following softdep should be added to a modprobe.d file
softdep arizona-spi pre: arizona-ldo1
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: rpi-cirrus: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
gtrainavicius [Sun, 23 Oct 2016 09:06:53 +0000 (12:06 +0300)]
Support for Blokas Labs pisound board
Pisound dynamic overlay (#1760)
Restructuring pisound-overlay.dts, so it can be loaded and unloaded dynamically using dtoverlay.
Print a logline when the kernel module is removed.
pisound improvements:
* Added a writable sysfs object to enable scripts / user space software
to blink MIDI activity LEDs for variable duration.
* Improved hw_param constraints setting.
* Added compatibility with S16_LE sample format.
* Exposed some simple placeholder volume controls, so the card appears
in volumealsa widget.
Add missing SND_PISOUND selects dependency to SND_RAWMIDI
Without it the Pisound module fails to compile.
See https://github.com/raspberrypi/linux/issues/2366
Updates for Pisound module code:
* Merged 'Fix a warning in DEBUG builds' (1c8b82b).
* Updating some strings and copyright information.
* Fix for handling high load of MIDI input and output.
* Use dual rate oversampling ratio for 96kHz instead of single
rate one.
Signed-off-by: Giedrius Trainavicius <giedrius@blokas.io>
Fixing memset call in pisound.c
Signed-off-by: Giedrius Trainavicius <giedrius@blokas.io>
Fix for Pisound's MIDI Input getting blocked for a while in rare cases.
There was a possible race condition which could lead to Input's FIFO queue
to be underflown, causing high amount of processing in the worker thread for
some period of time.
Signed-off-by: Giedrius Trainavicius <giedrius@blokas.io>
Fix for Pisound kernel module in Real Time kernel configuration.
When handler of data_available interrupt is fired, queue_work ends up
getting called and it can block on a spin lock which is not allowed in
interrupt context. The fix was to run the handler from a thread context
instead.
Pisound: Remove spinlock usage around spi_sync
ASoC: pisound: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
ASoC: pisound: fix the parameter for spi_device_match
Signed-off-by: Hui Wang <hui.wang@canonical.com>
BabuSubashChandar [Tue, 28 Mar 2017 14:34:42 +0000 (20:04 +0530)]
Add support for Allo Boss DAC add-on board for Raspberry Pi. (#1924)
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Deepak <deepak@zilogic.com>
Reviewed-by: BabuSubashChandar <babusubashchandar@zilogic.com>
Add support for new clock rate and mute gpios.
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Deepak <deepak@zilogic.com>
Reviewed-by: BabuSubashChandar <babusubashchandar@zilogic.com>
ASoC: allo-boss-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: allo-boss-dac: transmit S24_LE with 64 BCLK cycles
Signed-off-by: Matthias Reichl <hias@horus.com>
allo-boss-dac: switch to snd_soc_dai_set_bclk_ratio
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: allo-boss-dac: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Raashid Muhammed [Mon, 27 Mar 2017 07:05:00 +0000 (12:35 +0530)]
Add support for Allo Piano DAC 2.1 plus add-on board for Raspberry Pi.
The Piano DAC 2.1 has support for 4 channels with subwoofer.
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Vijay Kumar B. <vijaykumar@zilogic.com>
Reviewed-by: Raashid Muhammed <raashidmuhammed@zilogic.com>
Add clock changes and mute gpios (#1938)
Also improve code style and adhere to ALSA coding conventions.
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Reviewed-by: Vijay Kumar B. <vijaykumar@zilogic.com>
Reviewed-by: Raashid Muhammed <raashidmuhammed@zilogic.com>
PianoPlus: Dual Mono & Dual Stereo features added (#2069)
allo-piano-dac-plus: Master volume added + fixes
Master volume added, which controls both DACs volumes.
See: https://github.com/raspberrypi/linux/pull/2149
Also fix initial max volume, default mode value, and unmute.
Signed-off-by: allocom <sparky-dev@allo.com>
ASoC: allo-piano-dac-plus: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
sound: bcm: Fix memset dereference warning
This warning appears with GCC 6.4.0 from toolchains.bootlin.com:
../sound/soc/bcm/allo-piano-dac-plus.c: In function ‘snd_allo_piano_dac_init’:
../sound/soc/bcm/allo-piano-dac-plus.c:711:30: warning: argument to ‘sizeof’ in ‘memset’ call is the same expression as the destination; did you mean to dereference it? [-Wsizeof-pointer-memaccess]
memset(glb_ptr, 0x00, sizeof(glb_ptr));
^
Suggested-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
ASoC: allo-piano-dac-plus: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Clive Messer [Mon, 19 Sep 2016 13:01:04 +0000 (14:01 +0100)]
Allo Piano DAC boards: Initial 2 channel (stereo) support (#1645)
Add initial 2 channel (stereo) support for Allo Piano DAC (2.0/2.1) boards,
using allo-piano-dac-pcm512x-audio overlay and allo-piano-dac ALSA ASoC
machine driver.
NB. The initial support is 2 channel (stereo) ONLY!
(The Piano DAC 2.1 will only support 2 channel (stereo) left/right output,
pending an update to the upstream pcm512x codec driver, which will have
to be submitted via upstream. With the initial downstream support,
provided by this patch, the Piano DAC 2.1 subwoofer outputs will
not function.)
Signed-off-by: Baswaraj K <jaikumar@cem-solutions.net>
Signed-off-by: Clive Messer <clive.messer@digitaldreamtime.co.uk>
Tested-by: Clive Messer <clive.messer@digitaldreamtime.co.uk>
ASoC: allo-piano-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Also remove hw_params and ops as they are no longer needed.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: allo-piano-dac: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
DigitalDreamtime [Sat, 2 Jul 2016 15:26:19 +0000 (16:26 +0100)]
Add support for Dion Audio LOCO DAC-AMP HAT
Using dedicated machine driver and pcm5102a codec driver.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
ASoC: dionaudio_loco: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
escalator2015 [Tue, 24 May 2016 15:20:09 +0000 (16:20 +0100)]
New driver for RRA DigiDAC1 soundcard using WM8741 + WM8804
ASoC: digidac1-soundcard: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Matt Flax [Mon, 16 May 2016 11:36:31 +0000 (21:36 +1000)]
New AudioInjector.net Pi soundcard with low jitter audio in and out.
Contains the sound/soc/bcm ALSA machine driver and necessary alterations to the Kconfig and Makefile.
Adds the dts overlay and updates the Makefile and README.
Updates the relevant defconfig files to enable building for the Raspberry Pi.
Thanks to Phil Elwell (pelwell) for the review, simple-card concepts and discussion. Thanks to Clive Messer for overlay naming suggestions.
Added support for headphones, microphone and bclk_ratio settings.
This patch adds headphone and microphone capability to the Audio Injector sound card. The patch also sets the bit clock ratio for use in the bcm2835-i2s driver. The bcm2835-i2s can't handle an 8 kHz sample rate when the bit clock is at 12 MHz because its register is only 10 bits wide which can't represent the ch2 offset of 1508. For that reason, the rate constraint is added.
ASoC: audioinjector-pi-soundcard: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Aaron Shaw [Thu, 7 Apr 2016 20:26:21 +0000 (21:26 +0100)]
Add Support for JustBoom Audio boards
justboom-dac: Adjust for ALSA API change
As of 4.4, snd_soc_limit_volume now takes a struct snd_soc_card *
rather than a struct snd_soc_codec *.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
ASoC: justboom-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Also remove hw_params as it's no longer needed.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: justboom-dac: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
Waldemar Brodkorb [Wed, 25 Mar 2015 08:26:17 +0000 (09:26 +0100)]
Add driver for rpi-proto
Forward port of 3.10.x driver from https://github.com/koalo
We are using a custom board and would like to use rpi 3.18.x
kernel. Patch works fine for our embedded system.
URL to the audio chip:
http://www.mikroe.com/add-on-boards/audio-voice/audio-codec-proto/
Playback tested with devicetree enabled.
Signed-off-by: Waldemar Brodkorb <wbrodkorb@conet.de>
ASoC: rpi-proto: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Daniel Matuschek [Mon, 4 Aug 2014 09:09:58 +0000 (11:09 +0200)]
Added driver for HiFiBerry Amp amplifier add-on board
The driver contains a low-level hardware driver for the TAS5713 and the
drivers for the Raspberry Pi I2S subsystem.
TAS5713: return error if initialisation fails
Existing TAS5713 driver logs errors during initialisation, but does not return
an error code. Therefore even if initialisation fails, the driver will still be
loaded, but won't work. This patch fixes this. I2C communication error will now
reported correctly by a non-zero return code.
HiFiBerry Amp: fix device-tree problems
Some code to load the driver based on device-tree-overlays was missing. This is added by this patch.
Daniel Matuschek [Mon, 4 Aug 2014 08:06:56 +0000 (10:06 +0200)]
Added support for HiFiBerry DAC+
The driver is based on the HiFiBerry DAC driver. However HiFiBerry DAC+ uses
a different codec chip (PCM5122), therefore a new driver is necessary.
Add support for the HiFiBerry DAC+ Pro.
The HiFiBerry DAC+ and DAC+ Pro products both use the existing bcm sound driver with the DAC+ Pro having a special clock device driver representing the two high precision oscillators.
An addition bug fix is included for the PCM512x codec where by the physical size of the sample frame is used in the calculation of the LRCK divisor as it was found to be wrong when using 24-bit depth sample contained in a little endian 4-byte sample frame.
Limit PCM512x "Digital" gain to 0dB by default with HiFiBerry DAC+
24db_digital_gain DT param can be used to specify that PCM512x
codec "Digital" volume control should not be limited to 0dB gain,
and if specified will allow the full 24dB gain.
Add dt param to force HiFiBerry DAC+ Pro into slave mode
"dtoverlay=hifiberry-dacplus,slave"
Add 'slave' param to use HiFiBerry DAC+ Pro in slave mode,
with Pi as master for bit and frame clock.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
Fixed a bug when using 352.8kHz sample rate
Signed-off-by: Daniel Matuschek <daniel@hifiberry.com>
ASoC: pcm512x: revert downstream changes
This partially reverts commit
185ea05465aac8bf02a0d2b2f4289d42c72870b7
which was added by https://github.com/raspberrypi/linux/pull/1152
The downstream pcm512x changes caused a regression, it broke normal
use of the 24bit format with the codec, eg when using simple-audio-card.
The actual bug with 24bit playback is the incorrect usage
of physical_width in various drivers in the downstream tree
which causes 24bit data to be transmitted with 32 clock
cycles. So it's not the pcm512x that needs fixing, it's the
soundcard drivers.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplus: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplus: transmit S24_LE with 64 BCLK cycles
Signed-off-by: Matthias Reichl <hias@horus.com>
hifiberry_dacplus: switch to snd_soc_dai_set_bclk_ratio
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: hifiberry_dacplus: use modern dai_link style
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Gordon Garrity [Sat, 8 Mar 2014 16:56:57 +0000 (16:56 +0000)]
Add IQaudIO Sound Card support for Raspberry Pi
Set a limit of 0dB on Digital Volume Control
The main volume control in the PCM512x DAC has a range up to
+24dB. This is dangerously loud and can potentially cause massive
clipping in the output stages. Therefore this sets a sensible
limit of 0dB for this control.
Allow up to 24dB digital gain to be applied when using IQAudIO DAC+
24db_digital_gain DT param can be used to specify that PCM512x
codec "Digital" volume control should not be limited to 0dB gain,
and if specified will allow the full 24dB gain.
Modify IQAudIO DAC+ ASoC driver to set card/dai config from dt
Add the ability to set the card name, dai name and dai stream name, from
dt config.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
IQaudIO: auto-mute for AMP+ and DigiAMP+
IQAudIO amplifier mute via GPIO22. Add dt params for "one-shot" unmute
and auto mute.
Revision 2, auto mute implementing HiassofT suggestion to mute/unmute
using set_bias_level, rather than startup/shutdown....
"By default DAPM waits 5 seconds (pmdown_time) before shutting down
playback streams so a close/stop immediately followed by open/start
doesn't trigger an amp mute+unmute."
Tested on both AMP+ (via DAC+) and DigiAMP+, with both options...
dtoverlay=iqaudio-dacplus,unmute_amp
"one-shot" unmute when kernel module loads.
dtoverlay=iqaudio-dacplus,auto_mute_amp
Unmute amp when ALSA device opened by a client. Mute, with 5 second delay
when ALSA device closed. (Re-opening the device within the 5 second close
window, will cancel mute.)
Revision 4, using gpiod.
Revision 5, clean-up formatting before adding mute code.
- Convert tab plus 4 space formatting to 2x tab
- Remove '// NOT USED' commented code
Revision 6, don't attempt to "one-shot" unmute amp, unless card is
successfully registered.
Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
ASoC: iqaudio-dac: fix S24_LE format
Remove set_bclk_ratio call so 24-bit data is transmitted in
24 bclk cycles.
Signed-off-by: Matthias Reichl <hias@horus.com>
ASoC: iqaudio-dac: use modern dai_link style
Signed-off-by: Matthias Reichl <hias@horus.com>
Florian Meier [Mon, 25 Jan 2016 15:48:59 +0000 (15:48 +0000)]
ASoC: Add support for Rpi-DAC
Phil Elwell [Tue, 14 Jul 2015 13:32:47 +0000 (14:32 +0100)]
mfd: Add Raspberry Pi Sense HAT core driver
mfd: Add rpi_sense_core of compatible string
Phil Elwell [Thu, 25 Jun 2015 11:16:11 +0000 (12:16 +0100)]
gpio-poweroff: Allow it to work on Raspberry Pi
The Raspberry Pi firmware manages the power-down and reboot
process. To do this it installs a pm_power_off handler, causing
the gpio-poweroff module to abort the probe function.
This patch introduces a "force" DT property that overrides that
behaviour, and also adds a DT overlay to enable and control it.
Note that running in an active-low configuration (DT parameter
"active_low") requires a custom dt-blob.bin and probably won't
allow a reboot without switching off, so an external inversion
of the trigger signal may be preferable.
popcornmix [Mon, 28 Nov 2016 16:50:04 +0000 (16:50 +0000)]
Improve __copy_to_user and __copy_from_user performance
Provide a __copy_from_user that uses memcpy. On BCM2708, use
optimised memcpy/memmove/memcmp/memset implementations.
arch/arm: Add mmiocpy/set aliases for memcpy/set
See: https://github.com/raspberrypi/linux/issues/1082
copy_from_user: CPU_SW_DOMAIN_PAN compatibility
The downstream copy_from_user acceleration must also play nice with
CONFIG_CPU_SW_DOMAIN_PAN.
See: https://github.com/raspberrypi/linux/issues/1381
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
popcornmix [Tue, 2 Jul 2013 23:54:08 +0000 (00:54 +0100)]
Added Device IDs for August DVB-T 205
Phil Elwell [Fri, 6 Feb 2015 13:50:57 +0000 (13:50 +0000)]
BCM270x_DT: Add pwr_led, and the required "input" trigger
The "input" trigger makes the associated GPIO an input. This is to support
the Raspberry Pi PWR LED, which is driven by external hardware in normal use.
N.B. pwr_led is not available on Model A or B boards.
leds-gpio: Implement the brightness_get method
The power LED uses some clever logic that means it is driven
by a voltage measuring circuit when configured as input, otherwise
it is driven by the GPIO output value. This patch wires up the
brightness_get method for leds-gpio so that user-space can monitor
the LED value via /sys/class/gpio/led1/brightness. Using the input
trigger this returns an indication of the system power health,
otherwise it is just whatever value the trigger has written most
recently.
See: https://github.com/raspberrypi/linux/issues/1064
notro [Wed, 9 Jul 2014 12:46:08 +0000 (14:46 +0200)]
BCM2708: Add core Device Tree support
Add the bare minimum needed to boot BCM2708 from a Device Tree.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
BCM2708: DT: change 'axi' nodename to 'soc'
Change DT node named 'axi' to 'soc' so it matches ARCH_BCM2835.
The VC4 bootloader fills in certain properties in the 'axi' subtree,
but since this is part of an upstreaming effort, the name is changed.
Signed-off-by: Noralf Tronnes notro@tronnes.org
BCM2708_DT: Correct length of the peripheral space
Use dts-dirs feature for overlays.
The kernel makefiles have a dts-dirs target that is for vendor subdirectories.
Using this fixes the install_dtbs target, which previously did not install the overlays.
BCM270X_DT: configure I2S DMA channels
Signed-off-by: Matthias Reichl <hias@horus.com>
BCM270X_DT: switch to bcm2835-i2s
I2S soundcard drivers with proper devicetree support (i.e. not linking
to the cpu_dai/platform via name but to cpu/platform via of_node)
will work out of the box without any modifications.
When the kernel is compiled without devicetree support the platform
code will instantiate the bcm2708-i2s driver and I2S soundcard drivers
will link to it via name, as before.
Signed-off-by: Matthias Reichl <hias@horus.com>
SDIO-overlay: add poll_once-boolean parameter
Add paramter to toggle sdio-device-polling
done every second or once at boot-time.
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
BCM270X_DT: Make mmc overlay compatible with current firmware
The original DT overlay logic followed a merge-then-patch procedure,
i.e. parameters are applied to the loaded overlay before the overlay
is merged into the base DTB. This sequence has been changed to
patch-then-merge, in order to support parameterised node names, and
to protect against bad overlays. As a result, overrides (parameters)
must only target labels in the overlay, but the overlay can obviously target nodes in the base DTB.
mmc-overlay.dts (that switches back to the original mmc sdcard
driver) is the only overlay violating that rule, and this patch
fixes it.
bcm270x_dt: Use the sdhost MMC controller by default
The "mmc" overlay reverts to using the other controller.
squash: Add cprman to dt
BCM270X_DT: Use clk_core for I2C interfaces
BCM270X_DT: Use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi
The mainline Device Tree files are quite close to downstream now.
Let's use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi as base files
for our dts files.
Mainline dts files are based on these files:
bcm2835-rpi.dtsi
bcm2835.dtsi bcm2836.dtsi
bcm283x.dtsi
Current downstream are based on these:
bcm2708.dtsi bcm2709.dtsi bcm2710.dtsi
bcm2708_common.dtsi
This patch introduces this dependency:
bcm2708.dtsi bcm2709.dtsi
bcm2708-rpi.dtsi
bcm270x.dtsi
bcm2835.dtsi bcm2836.dtsi
bcm283x.dtsi
And:
bcm2710.dtsi
bcm2708-rpi.dtsi
bcm270x.dtsi
bcm283x.dtsi
bcm270x.dtsi contains the downstream bcm283x.dtsi diff.
bcm2708-rpi.dtsi is the downstream version of bcm2835-rpi.dtsi.
Other changes:
- The led node has moved from /soc/leds to /leds. This is not a problem
since the label is used to reference it.
- The clk_osc reg property changes from 6 to 3.
- The gpu nodes has their interrupt property set in the base file.
- the clocks label does not point to the /clocks node anymore, but
points to the cprman node. This is not a problem since the overlays
that use the clock node refer to it directly: target-path = "/clocks";
- some nodes now have 2 labels since mainline and downstream differs in
this respect: cprman/clocks, spi0/spi, gpu/vc4.
- some nodes doesn't have an explicit status = "okay" since they're not
disabled in the base file: watchdog and random.
- gpiomem doesn't need an explicit status = "okay".
- bcm2708-rpi-cm.dts got the hpd-gpios property from bcm2708_common.dtsi,
it's now set directly in that file.
- bcm2709-rpi-2-b.dts has the timer node moved from /soc/timer to /timer.
- Removed clock-frequency property on the bcm{2709,2710}.dtsi timer nodes.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270X_DT: Use raspberrypi-power to turn on USB power
Use the raspberrypi-power driver to turn on USB power.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270X_DT: Add a .dtbo target, use for overlays
Change the filenames and extensions to keep the pre-DDT style of
overlay (<name>-overlay.dtb) distinct from new ones that use a
different style of local fixups (<name>.dtbo), and to match other
platforms.
The RPi firmware uses the DDTK trailer atom to choose which type of
overlay to use for each kernel.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Don't generate "linux,phandle" props
The EPAPR standard says to use "phandle" properties to store phandles,
rather than the deprecated "linux,phandle" version. By default, dtc
generates both, but adding "-H epapr" causes it to only generate
"phandle"s, saving some space and clutter.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Add overlay for enc28j60 on SPI2
Works on SPI2 for compute module
BCM270X_DT: Add midi-uart0 overlay
MIDI requires 31.25kbaud, a baudrate unsupported by Linux. The
midi-uart0 overlay configures uart0 (ttyAMA0) to use a fake clock
so that requesting 38.4kbaud actually gets 31.25kbaud.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Add i2c-sensor overlay
The i2c-sensor overlay is a container for various pressure and
temperature sensors, currently bmp085 and bmp280. The standalone
bmp085_i2c-sensor overlay is now deprecated.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: overlays/*-overlay.dtb -> overlays/*.dtbo (#1752)
We now create overlays as .dtbo files.
build: support for .dtbo files for dtb overlays
Kernel 4.4.6+ on RaspberryPi support .dtbo files for overlays, instead of .dtb.
Patch the kernel, which has faulty rules to generate .dtbo the way yocto does
Signed-off-by: Herve Jourdain <herve.jourdain@neuf.fr>
Signed-off-by: Khem Raj <raj.khem@gmail.com>
BCM270X: Drop position requirement for CMA in VC4 overlay.
No longer necessary since
2aefcd576195a739a7a256099571c9c4a401005f,
and will probably let peeople that want to choose a larger CMA
allocation (particularly on pi0/1).
Signed-off-by: Eric Anholt <eric@anholt.net>
BCM270X_DT: RPi Device Tree tidy
Use the upstream sdhost node, add thermal-zones, and factor out some
common elements.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
kbuild: Silence unhelpful DTC warnings
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: DT build rules no longer arch-specific
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Noralf Trønnes [Fri, 26 Jun 2015 12:25:01 +0000 (14:25 +0200)]
firmware: bcm2835: Support ARCH_BCM270x
Support booting without Device Tree.
Turn on USB power.
Load driver early because of lacking support for deferred probing
in many drivers.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
firmware: bcm2835: Don't turn on USB power
The raspberrypi-power driver is now used to turn on USB power.
This partly reverts commit:
firmware: bcm2835: Support ARCH_BCM270x
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Noralf Trønnes [Fri, 26 Jun 2015 12:27:06 +0000 (14:27 +0200)]
char: broadcom: Add vcio module
Add module for accessing the mailbox property channel through
/dev/vcio. Was previously in bcm2708-vcio.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
char: vcio: Add compat ioctl handling
There was no compat ioctl handler, so 32 bit userspace on a
64 bit kernel failed as IOCTL_MBOX_PROPERTY used the size
of char*.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
char: vcio: Fail probe if rpi_firmware is not found.
Device Tree is now the only supported config mechanism, therefore
uncomment the block of code that fails the probe if the
firmware node can't be found.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
popcornmix [Wed, 17 Jun 2015 14:44:08 +0000 (15:44 +0100)]
Add Chris Boot's i2c driver
i2c-bcm2708: fixed baudrate
Fixed issue where the wrong CDIV value was set for baudrates below 3815 Hz (for 250MHz bus clock).
In that case the computed CDIV value was more than 0xffff. However the CDIV register width is only 16 bits.
This resulted in incorrect setting of CDIV and higher baudrate than intended.
Example: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0x1704 -> 42430Hz
After correction: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0xffff -> 3815Hz
The correct baudrate is shown in the log after the cdiv > 0xffff correction.
Perform I2C combined transactions when possible
Perform I2C combined transactions whenever possible, within the
restrictions of the Broadcomm Serial Controller.
Disable DONE interrupt during TA poll
Prevent interrupt from being triggered if poll is missed and transfer
starts and finishes.
i2c: Make combined transactions optional and disabled by default
i2c: bcm2708: add device tree support
Add DT support to driver and add to .dtsi file.
Setup pins in .dts file.
i2c is disabled by default.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
bcm2708: don't register i2c controllers when using DT
The devices for the i2c controllers are in the Device Tree.
Only register devices when not using DT.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
I2C: Only register the I2C device for the current board revision
i2c_bcm2708: Fix clock reference counting
Fix grabbing lock from atomic context in i2c driver
2 main changes:
- check for timeouts in the bcm2708_bsc_setup function as indicated by this comment:
/* poll for transfer start bit (should only take 1-20 polls) */
This implies that the setup function can now fail so account for this everywhere it's called
- Removed the clk_get_rate call from inside the setup function as it locks a mutex and that's not ok since we call it from under a spin lock.
i2c-bcm2708: When using DT, leave the GPIO setup to pinctrl
i2c-bcm2708: Increase timeouts to allow larger transfers
Use the timeout value provided by the I2C_TIMEOUT ioctl when waiting
for completion. The default timeout is 1 second.
See: https://github.com/raspberrypi/linux/issues/260
i2c-bcm2708/BCM270X_DT: Add support for I2C2
The third I2C bus (I2C2) is normally reserved for HDMI use. Careless
use of this bus can break an attached display - use with caution.
It is recommended to disable accesses by VideoCore by setting
hdmi_ignore_edid=1 or hdmi_edid_file=1 in config.txt.
The interface is disabled by default - enable using the
i2c2_iknowwhatimdoing DT parameter.
bcm2708-spi: Don't use static pin configuration with DT
Also remove superfluous error checking - the SPI framework ensures the
validity of the chip_select value.
i2c-bcm2708: Remove non-DT support
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Set the BSC_CLKT clock streching timeout to 35ms as per SMBus specs.
Fixes i2c_bcm2708: Write to FIFO correctly - v2 (#1574)
* i2c: fix i2c_bcm2708: Clear FIFO before sending data
Make sure FIFO gets cleared before trying to send
data in case of a repeated start (COMBINED=Y).
* i2c: fix i2c_bcm2708: Only write to FIFO when not full
Check if FIFO can accept data before writing.
To avoid a peripheral read on the last iteration of a loop,
both bcm2708_bsc_fifo_fill and ~drain are changed as well.
popcornmix [Tue, 2 Jul 2013 23:49:20 +0000 (00:49 +0100)]
Add cpufreq driver
Signed-off-by: popcornmix <popcornmix@gmail.com>
bcm2835-cpufreq: Change licence to GPLv2
Signed-off-by: Eben Upton <eben.upton@broadcom.com>
Signed-off-by: Dom Cobley <dom@raspberrypi.com>
Luke Wren [Sat, 5 Sep 2015 00:14:45 +0000 (01:14 +0100)]
Add SMI driver
Signed-off-by: Luke Wren <wren6991@gmail.com>
MISC: bcm2835: smi: use clock manager and fix reload issues
Use clock manager instead of self-made clockmanager.
Also fix some error paths that showd up during development
(especially missing release of dma resources on rmmod)
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
bcm2835_smi: re-add dereference to fix DMA transfers
Luke Wren [Fri, 21 Aug 2015 22:14:48 +0000 (23:14 +0100)]
Add /dev/gpiomem device for rootless user GPIO access
Signed-off-by: Luke Wren <luke@raspberrypi.org>
bcm2835-gpiomem: Fix for ARCH_BCM2835 builds
Build on ARCH_BCM2835, and fail to probe if no IO resource.
See: https://github.com/raspberrypi/linux/issues/1154
Tim Gover [Tue, 22 Jul 2014 14:41:04 +0000 (15:41 +0100)]
vcsm: VideoCore shared memory service for BCM2835
Add experimental support for the VideoCore shared memory service.
This allows user processes to allocate memory from VideoCore's
GPU relocatable heap and mmap the buffers. Additionally, the memory
handles can passed to other VideoCore services such as MMAL, OpenMax
and DispmanX
TODO
* This driver was originally released for BCM28155 which has a different
cache architecture to BCM2835. Consequently, in this release only
uncached mappings are supported. However, there's no fundamental
reason which cached mappings cannot be support or BCM2835
* More refactoring is required to remove the typedefs.
* Re-enable the some of the commented out debug-fs statistics which were
disabled when migrating code from proc-fs.
* There's a lot of code to support sharing of VCSM in order to support
Android. This could probably done more cleanly or perhaps just
removed.
Signed-off-by: Tim Gover <timgover@gmail.com>
config: Disable VC_SM for now to fix hang with cutdown kernel
vcsm: Use boolean as it cannot be built as module
On building the bcm_vc_sm as a module we get the following error:
v7_dma_flush_range and do_munmap are undefined in vc-sm.ko.
Fix by making it not an option to build as module
vcsm: Add ioctl for custom cache flushing
vc-sm: Move headers out of arch directory
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
vcsm: Treat EBUSY as success rather than SIGBUS
Currently if two cores access the same page concurrently one will return VM_FAULT_NOPAGE
and the other VM_FAULT_SIGBUS crashing the user code.
Also report when mapping fails.
Signed-off-by: popcornmix <popcornmix@gmail.com>
vcsm: Provide new ioctl to clean/invalidate a 2D block
vcsm: Convert to loading via device tree.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
VCSM: New option to import a DMABUF for VPU use
Takes a dmabuf, and then calls over to the VPU to wrap
it into a suitable handle.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
vcsm: fix multi-platform build
vcsm: add macros for cache functions
vcsm: use dma APIs for cache functions
* Will handle multi-platform builds
vcsm: Fix up macros to avoid breaking numbers used by existing apps
vcsm: Define cache operation constants in user header
Without this change, users have to use raw values (1, 2, 3) to specify
cache operation.
Signed-off-by: Sugizaki Yukimasa <i.can.speak.c.and.basic@gmail.com>
vcsm: Support for finding user/vc handle in memory pool
vmcs_sm_{usr,vc}_handle_from_pid_and_address() were failing to find
handle if specified user pointer is not exactly the one that the memory
locking call returned even if the pointer is in range of map/resource.
So fixed the functions to match the range.
Signed-off-by: Sugizaki Yukimasa <i.can.speak.c.and.basic@gmail.com>
vcsm: Unify cache manipulating functions
Signed-off-by: Sugizaki Yukimasa <i.can.speak.c.and.basic@gmail.com>
vcsm: Fix obscure conditions
Signed-off-by: Sugizaki Yukimasa <i.can.speak.c.and.basic@gmail.com>
vcsm: Fix memory leaking on clean_invalid2 ioctl handler
Signed-off-by: Sugizaki Yukimasa <i.can.speak.c.and.basic@gmail.com>
vcsm: Describe the use of cache operation constants
Signed-off-by: Sugizaki Yukimasa <i.can.speak.c.and.basic@gmail.com>
vcsm: Fix obscure conditions again
Signed-off-by: Sugizaki Yukimasa <i.can.speak.c.and.basic@gmail.com>
vcsm: Add no-op cache operation constant
Signed-off-by: Sugizaki Yukimasa <i.can.speak.c.and.basic@gmail.com>
vcsm: Revert to do page-table-walk-based cache manipulating on some ioctl calls
On FLUSH, INVALID, CLEAN_INVALID ioctl calls, cache operations based on
page table walk were used in case that the buffer of the cache is not
pinned. So reverted to do page-table-based cache manipulating.
Signed-off-by: Sugizaki Yukimasa <i.can.speak.c.and.basic@gmail.com>
vcsm: Define cache operation constants in user header
Without this change, users have to use raw values (1, 2, 3) to specify
cache operation.
Signed-off-by: Sugizaki Yukimasa <i.can.speak.c.and.basic@gmail.com>
vcsm: Updates for changed vchiq interface
vcsm: Fix an NULL dereference in the import_dmabuf error path
resource was dereferenced even though it was NULL.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
vcsm: Use struct service_creation
vcsm: Fix makefile include on out-of-tree builds
The vc_sm module tries to include the 'fs' directory from the
$(srctree). $(srctree) is already provided by the build system, and
causes the include path to be duplicated.
With -Werror this fails to compile.
Remove the unnecessary variable.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
vcsm: Remove set but unused variable
The 'success' variable is set by the call to vchi_service_close() but never checked.
Remove it, keeping the call in place.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
vcsm: Reduce scope of local functions
The functions:
vc_vchi_sm_send_msg
vc_sm_ioctl_alloc
vc_sm_ioctl_alloc_share
vc_sm_ioctl_import_dmabuf
Are declared without a prototype. They are not used outside of this
module, thus - convert them to static functions.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
vc_sm: Let it support to build in the non-src folder
If we build the kernel with "-O=$non-src-folder", this driver will
introdcue a building error because of the header's location.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
popcornmix [Fri, 28 Oct 2016 14:36:43 +0000 (15:36 +0100)]
vc_mem: Add vc_mem driver for querying firmware memory addresses
Signed-off-by: popcornmix <popcornmix@gmail.com>
BCM270x: Move vc_mem
Make the vc_mem module available for ARCH_BCM2835 by moving it.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
char: vc_mem: Fix up compat ioctls for 64bit kernel
compat_ioctl wasn't defined, so 32bit user/64bit kernel
always failed.
VC_MEM_IOC_MEM_PHYS_ADDR was defined with parameter size
unsigned long, so the ioctl cmd changes between sizes.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
char: vc_mem: Fix all coding style issues.
Cleans up all checkpatch errors in vc_mem.c and vc_mem.h
No functional change to the code.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Phil Elwell [Wed, 25 Mar 2015 17:49:47 +0000 (17:49 +0000)]
Adding bcm2835-sdhost driver, and an overlay to enable it
BCM2835 has two SD card interfaces. This driver uses the other one.
bcm2835-sdhost: Error handling fix, and code clarification
bcm2835-sdhost: Adding overclocking option
Allow a different clock speed to be substitued for a requested 50MHz.
This option is exposed using the "overclock_50" DT parameter.
Note that the sdhost interface is restricted to integer divisions of
core_freq, and the highest sensible option for a core_freq of 250MHz
is 84 (250/3 = 83.3MHz), the next being 125 (250/2) which is much too
high.
Use at your own risk.
bcm2835-sdhost: Round up the overclock, so 62 works for 62.5Mhz
Also only warn once for each overclock setting.
bcm2835-sdhost: Improve error handling and recovery
1) Expose the hw_reset method to the MMC framework, removing many
internal calls by the driver.
2) Reduce overclock setting on error.
3) Increase timeout to cope with high capacity cards.
4) Add properties and parameters to control pio_limit and debug.
5) Reduce messages at probe time.
bcm2835-sdhost: Further improve overclock back-off
bcm2835-sdhost: Clear HBLC for PIO mode
Also update pio_limit default in overlay README.
bcm2835-sdhost: Add the ERASE capability
See: https://github.com/raspberrypi/linux/issues/1076
bcm2835-sdhost: Ignore CRC7 for MMC CMD1
It seems that the sdhost interface returns CRC7 errors for CMD1,
which is the MMC-specific SEND_OP_COND. Returning these errors to
the MMC layer causes a downward spiral, but ignoring them seems
to be harmless.
bcm2835-mmc/sdhost: Remove ARCH_BCM2835 differences
The bcm2835-mmc driver (and -sdhost driver that copied from it)
contains code to handle SDIO interrupts in a threaded interrupt
handler rather than waking the MMC framework thread. The change
follows a patch from Russell King that adds the facility as the
preferred way of working.
However, the new code path is only present in ARCH_BCM2835
builds, which I have taken to be a way of testing the waters
rather than making the change across the board; I can't see
any technical reason why it wouldn't be enabled for MACH_BCM270X
builds. So this patch standardises on the ARCH_BCM2835 code,
removing the old code paths.
bcm2835-sdhost: Don't log timeout errors unless debug=1
The MMC card-discovery process generates timeouts. This is
expected behaviour, so reporting it to the user serves no purpose.
Suppress the reporting of timeout errors unless the debug flag
is on.
bcm2835-sdhost: Add workaround for odd behaviour on some cards
For reasons not understood, the sdhost driver fails when reading
sectors very near the end of some SD cards. The problem could
be related to the similar issue that reading the final sector
of any card as part of a multiple read never completes, and the
workaround is an extension of the mechanism introduced to solve
that problem which ensures those sectors are always read singly.
bcm2835-sdhost: Major revision
This is a significant revision of the bcm2835-sdhost driver. It
improves on the original in a number of ways:
1) Through the use of CMD23 for reads it appears to avoid problems
reading some sectors on certain high speed cards.
2) Better atomicity to prevent crashes.
3) Higher performance.
4) Activity logging included, for easier diagnosis in the event
of a problem.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Restore ATOMIC flag to PIO sg mapping
Allocation problems have been seen in a wireless driver, and
this is the only change which might have been responsible.
SQUASH: bcm2835-sdhost: Only claim one DMA channel
With both MMC controllers enabled there are few DMA channels left. The
bcm2835-sdhost driver only uses DMA in one direction at a time, so it
doesn't need to claim two channels.
See: https://github.com/raspberrypi/linux/issues/1327
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Workaround for "slow" sectors
Some cards have been seen to cause timeouts after certain sectors are
read. This workaround enforces a minimum delay between the stop after
reading one of those sectors and a subsequent data command.
Using CMD23 (SET_BLOCK_COUNT) avoids this problem, so good cards will
not be penalised by this workaround.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Firmware manages the clock divisor
The bcm2835-sdhost driver hands control of the CDIV clock divisor
register to matching firmware, allowing it to adjust to a changing
core clock. This removes the need to use the performance governor or
to enable io_is_busy on the on-demand governor in order to get the
best SD performance.
N.B. As SD clocks must be an integer divisor of the core clock, it is
possible that the SD clock for "turbo" mode can be different (even
lower) than "normal" mode.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Reset the clock in task context
Since reprogramming the clock can now involve a round-trip to the
firmware it must not be done at atomic context, and a tasklet
is not a task.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Don't exit cmd wait loop on error
The FAIL flag can be set in the CMD register before command processing
is complete, leading to spurious "failed to complete" errors. This has
the effect of promoting harmless CRC7 errors during CMD1 processing
into errors that can delay and even prevent booting.
Also:
1) Convert the last KERN_ERROR message in the register dumping to
KERN_INFO.
2) Remove an unnecessary reset call from bcm2835_sdhost_add_host.
See: https://github.com/raspberrypi/linux/pull/1492
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: mmc_card_blockaddr fix
Get the definition of mmc_card_blockaddr from drivers/mmc/core/card.h.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: New timer API
mmc: bcm2835-sdhost: Support underclocking
Support underclocking of the SD bus in two ways:
1. using the max-frequency DT property (which currently has no DT
parameter), and
2. using the exiting sd_overclock parameter.
The two methods differ slightly - in the former the MMC subsystem is
aware of the underclocking, while in the latter it isn't - but the
end results should be the same.
See: https://github.com/raspberrypi/linux/issues/2350
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc: bcm2835-sdhost: Add include
highmem.h (needed for kmap_atomic) is pulled in by one of the other
include files, but only with some CONFIG settings. Make the inclusion
explicit to cater for cases where the CONFIG setting is absent.
See: https://github.com/raspberrypi/linux/issues/2366
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc/bcm2835-sdhost: Recover from MMC_SEND_EXT_CSD
If the user issues an "mmc extcsd read", the SD controller receives
what it thinks is a SEND_IF_COND command with an unexpected data block.
The resulting operations leave the FSM stuck in READWAIT, a state which
persists until the MMC framework resets the controller, by which point
the root filesystem is likely to have been unmounted.
A less heavyweight solution is to detect the condition and nudge the
FSM by asserting the (self-clearing) FORCE_DATA_MODE bit.
N.B. This workaround was essentially discovered by accident and without
a full understanding the inner workings of the controller, so it is
fortunate that the "fix" only modifies error paths.
See: https://github.com/raspberrypi/linux/issues/2728
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc: bcm2835-sdhost: Fix warnings on arm64
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Allow for sg entries that cross pages
The dma_complete handling code calculates a virtual address for a page
then adds an offset, but if the offset is more than a page and HIGHMEM
is in use then the summed address could be in an unmapped (or just
incorrect) page.
The upstream SDHOST driver allows for this possibility - copy the code
that does so.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-sdhost: Fix DMA channel leak on error/remove
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc: bcm2835-sdhost: Support 64-bit physical addresses
Signed-off-by: Phil Elwell <phil@raspberrypi.org>