Phil Elwell [Wed, 29 Jan 2020 09:35:19 +0000 (09:35 +0000)]
tty: amba-pl011: Avoid rare write-when-full error
Under some circumstances on BCM283x processors data loss can be
observed - a single byte missing from the TX output stream. These bytes
are always the last byte of a batch of 8 written from pl011_tx_chars
when from_irq is true, meaning that the FIFO full flag is not checked
before writing.
The transmit optimisation relies on the FIFO being half-empty when the
TX interrupt is raised. Instrumenting the driver further showed that
the failure case correlated with the TX FIFO full flag being set at the
point where the last byte was written to the data register, which
explains the data loss but not how the FIFO appeared to be prematurely
full. A possible explanation is that a FIFO write was in flight at the
time the interrupt was raised, but as yet there is no hypothesis as to
how this might occur.
In the absence of a clear understanding of the failure mechanism, avoid
the problem by checking the FIFO levels before writing the last byte of
the group, which will have minimal performance impact.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Fri, 24 Jan 2020 11:38:28 +0000 (11:38 +0000)]
tty: amba-pl011: Add un/throttle support
The PL011 driver lacks throttle and unthrottle methods. As a result,
sending more data to the Pi than it can immediately sink while CRTSCTS
is enabled causes a NULL pointer to be followed.
Add a throttle handler that disables the RX interrupts, and an
unthrottle handler that reenables them.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Thu, 11 Jul 2019 12:13:39 +0000 (13:13 +0100)]
tty: amba-pl011: Make TX optimisation conditional
pl011_tx_chars takes a "from_irq" parameter to reduce the number of
register accesses. When from_irq is true the function assumes that the
FIFO is half empty and writes up to half a FIFO's worth of bytes
without polling the FIFO status register, the reasoning being that
the function is being called as a result of the TX interrupt being
raised. This logic would work were it not for the fact that
pl011_rx_chars, called from pl011_int before pl011_tx_chars, releases
the spinlock before calling tty_flip_buffer_push.
A user thread writing to the UART claims the spinlock and ultimately
calls pl011_tx_chars with from_irq set to false. This reverts to the
older logic that polls the FIFO status register before sending every
byte. If this happen on an SMP system during the section of the IRQ
handler where the spinlock has been released, then by the time the TX
interrupt handler is called, the FIFO may already be full, and any
further writes are likely to be lost.
The fix involves adding a per-port flag that is true iff running from
within the interrupt handler and the spinlock has not yet been released.
This flag is then used as the value for the from_irq parameter of
pl011_tx_chars, causing polling to be used in the unsafe case.
Fixes:
1e84d22322ce ("serial/amba-pl011: Refactor and simplify TX FIFO handling")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Fri, 29 Sep 2017 09:32:19 +0000 (10:32 +0100)]
amba_pl011: Add cts-event-workaround DT property
The BCM2835 PL011 implementation seems to have a bug that can lead to a
transmission lockup if CTS changes frequently. A workaround was added to
the driver with a vendor-specific flag to enable it, but this flag is
currently not set for ARM implementations.
Add a "cts-event-workaround" property to Pi DTBs and use the presence
of that property to force the flag to be enabled in the driver.
See: https://github.com/raspberrypi/linux/issues/1280
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Fri, 29 Sep 2017 09:32:19 +0000 (10:32 +0100)]
amba_pl011: Insert mb() for correct FIFO handling
The pl011 register accessor functions use the _relaxed versions of the
standard readl() and writel() functions, meaning that there are no
automatic memory barriers. When polling a FIFO status register to check
for fullness, it is necessary to ensure that any outstanding writes have
completed; otherwise the flags are effectively stale, making it possible
that the next write is to a full FIFO.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Wed, 1 Mar 2017 16:07:39 +0000 (16:07 +0000)]
amba_pl011: Round input clock up
The UART clock is initialised to be as close to the requested
frequency as possible without exceeding it. Now that there is a
clock manager that returns the actual frequencies, an expected
48MHz clock is reported as
47999625. If the requested baudrate
== requested clock/16, there is no headroom and the slight
reduction in actual clock rate results in failure.
Detect cases where it looks like a "round" clock was chosen and
adjust the reported clock to match that "round" value. As the
code comment says:
/*
* If increasing a clock by less than 0.1% changes it
* from ..999.. to ..000.., round up.
*/
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Tue, 23 Feb 2016 17:26:48 +0000 (17:26 +0000)]
amba_pl011: Don't use DT aliases for numbering
The pl011 driver looks for DT aliases of the form "serial<n>",
and if found uses <n> as the device ID. This can cause
/dev/ttyAMA0 to become /dev/ttyAMA1, which is confusing if the
other serial port is provided by the 8250 driver which doesn't
use the same logic.
Phil Elwell [Tue, 17 Oct 2017 14:04:29 +0000 (15:04 +0100)]
lan78xx: Enable LEDs and auto-negotiation
For applications of the LAN78xx that don't have valid programmed
EEPROMs or OTPs, enabling both LEDs and auto-negotiation by default
seems reasonable.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Tue, 23 Jan 2018 16:52:45 +0000 (16:52 +0000)]
irqchip: irq-bcm2836: Remove regmap and syscon use
The syscon node defines a register range that duplicates that used by
the local_intc node on bcm2836/7. Since irq-bcm2835 and irq-bcm2836 are
built in and always present together (both drivers are enabled by
CONFIG_ARCH_BCM2835), it is possible to replace the syscon usage with a
global variable that simplifies the code. Doing so does lose the
locking provided by regmap, but as only one side is using the regmap
interface (irq-bcm2835 uses readl and write) there is no loss of
atomicity.
See: https://github.com/raspberrypi/firmware/issues/926
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Eric Anholt [Fri, 19 Dec 2014 00:07:15 +0000 (16:07 -0800)]
mm: Remove the PFN busy warning
See commit
dae803e165a11bc88ca8dbc07a11077caf97bbcb -- the warning is
expected sometimes when using CMA. However, that commit still spams
my kernel log with these warnings.
Signed-off-by: Eric Anholt <eric@anholt.net>
Noralf Trønnes [Tue, 1 Nov 2016 14:15:41 +0000 (15:15 +0100)]
i2c: bcm2835: Add debug support
This adds a debug module parameter to aid in debugging transfer issues
by printing info to the kernel log. When enabled, status values are
collected in the interrupt routine and msg info in
bcm2835_i2c_start_transfer(). This is done in a way that tries to avoid
affecting timing. Having printk in the isr can mask issues.
debug values (additive):
1: Print info on error
2: Print info on all transfers
3: Print messages before transfer is started
The value can be changed at runtime:
/sys/module/i2c_bcm2835/parameters/debug
Example output, debug=3:
[ 747.114448] bcm2835_i2c_xfer: msg(1/2) write addr=0x54, len=2 flags= [i2c1]
[ 747.114463] bcm2835_i2c_xfer: msg(2/2) read addr=0x54, len=32 flags= [i2c1]
[ 747.117809] start_transfer: msg(1/2) write addr=0x54, len=2 flags= [i2c1]
[ 747.117825] isr: remain=2, status=0x30000055 : TA TXW TXD TXE [i2c1]
[ 747.117839] start_transfer: msg(2/2) read addr=0x54, len=32 flags= [i2c1]
[ 747.117849] isr: remain=32, status=0xd0000039 : TA RXR TXD RXD [i2c1]
[ 747.117861] isr: remain=20, status=0xd0000039 : TA RXR TXD RXD [i2c1]
[ 747.117870] isr: remain=8, status=0x32 : DONE TXD RXD [i2c1]
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Claggy3 [Sat, 11 Feb 2017 14:00:30 +0000 (14:00 +0000)]
Update vfpmodule.c
Christopher Alexander Tobias Schulze - May 2, 2015, 11:57 a.m.
This patch fixes a problem with VFP state save and restore related
to exception handling (panic with message "BUG: unsupported FP
instruction in kernel mode") present on VFP11 floating point units
(as used with ARM1176JZF-S CPUs, e.g. on first generation Raspberry
Pi boards). This patch was developed and discussed on
https://github.com/raspberrypi/linux/issues/859
A precondition to see the crashes is that floating point exception
traps are enabled. In this case, the VFP11 might determine that a FPU
operation needs to trap at a point in time when it is not possible to
signal this to the ARM11 core any more. The VFP11 will then set the
FPEXC.EX bit and store the trapped opcode in FPINST. (In some cases,
a second opcode might have been accepted by the VFP11 before the
exception was detected and could be reported to the ARM11 - in this
case, the VFP11 also sets FPEXC.FP2V and stores the second opcode in
FPINST2.)
If FPEXC.EX is set, the VFP11 will "bounce" the next FPU opcode issued
by the ARM11 CPU, which will be seen by the ARM11 as an undefined opcode
trap. The VFP support code examines the FPEXC.EX and FPEXC.FP2V bits
to decide what actions to take, i.e., whether to emulate the opcodes
found in FPINST and FPINST2, and whether to retry the bounced instruction.
If a user space application has left the VFP11 in this "pending trap"
state, the next FPU opcode issued to the VFP11 might actually be the
VSTMIA operation vfp_save_state() uses to store the FPU registers
to memory (in our test cases, when building the signal stack frame).
In this case, the kernel crashes as described above.
This patch fixes the problem by making sure that vfp_save_state() is
always entered with FPEXC.EX cleared. (The current value of FPEXC has
already been saved, so this does not corrupt the context. Clearing
FPEXC.EX has no effects on FPINST or FPINST2. Also note that many
callers already modify FPEXC by setting FPEXC.EN before invoking
vfp_save_state().)
This patch also addresses a second problem related to FPEXC.EX: After
returning from signal handling, the kernel reloads the VFP context
from the user mode stack. However, the current code explicitly clears
both FPEXC.EX and FPEXC.FP2V during reload. As VFP11 requires these
bits to be preserved, this patch disables clearing them for VFP
implementations belonging to architecture 1. There should be no
negative side effects: the user can set both bits by executing FPU
opcodes anyway, and while user code may now place arbitrary values
into FPINST and FPINST2 (e.g., non-VFP ARM opcodes) the VFP support
code knows which instructions can be emulated, and rejects other
opcodes with "unhandled bounce" messages, so there should be no
security impact from allowing reloading FPEXC.EX and FPEXC.FP2V.
Signed-off-by: Christopher Alexander Tobias Schulze <cat.schulze@alice-dsl.net>
Phil Elwell [Thu, 9 Feb 2017 14:36:44 +0000 (14:36 +0000)]
sound: Demote deferral errors to INFO level
At present there is no mechanism to specify driver load order,
which can lead to deferrals and repeated retries until successful.
Since this situation is expected, reduce the dmesg level to
INFO and mention that the operation will be retried.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Mon, 6 Mar 2017 09:06:18 +0000 (09:06 +0000)]
clk-bcm2835: Read max core clock from firmware
The VPU is responsible for managing the core clock, usually under
direction from the bcm2835-cpufreq driver but not via the clk-bcm2835
driver. Since the core frequency can change without warning, it is
safer to report the maximum clock rate to users of the core clock -
I2C, SPI and the mini UART - to err on the safe side when calculating
clock divisors.
If the DT node for the clock driver includes a reference to the
firmware node, use the firmware API to query the maximum core clock
instead of reading the divider registers.
Prior to this patch, a "100KHz" I2C bus was sometimes clocked at about
160KHz. In particular, switching to the 4.9 kernel was likely to break
SenseHAT usage on a Pi3.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Mon, 13 Feb 2017 17:20:08 +0000 (17:20 +0000)]
clk-bcm2835: Add claim-clocks property
The claim-clocks property can be used to prevent PLLs and dividers
from being marked as critical. It contains a vector of clock IDs,
as defined by dt-bindings/clock/bcm2835.h.
Use this mechanism to claim PLLD_DSI0, PLLD_DSI1, PLLH_AUX and
PLLH_PIX for the vc4_kms_v3d driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Mon, 13 Feb 2017 17:20:08 +0000 (17:20 +0000)]
clk-bcm2835: Mark used PLLs and dividers CRITICAL
The VPU configures and relies on several PLLs and dividers. Mark all
enabled dividers and their PLLs as CRITICAL to prevent the kernel from
switching them off.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
popcornmix [Tue, 6 Dec 2016 17:05:39 +0000 (17:05 +0000)]
bcm2835-rng: Avoid initialising if already enabled
Avoids the 0x40000 cycles of warmup again if firmware has already used it
Martin Sperl [Fri, 2 Sep 2016 15:45:27 +0000 (16:45 +0100)]
Register the clocks early during the boot process, so that special/critical clocks can get enabled early on in the boot process avoiding the risk of disabling a clock, pll_divider or pll when a claiming driver fails to install propperly - maybe it needs to defer.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
popcornmix [Wed, 9 Nov 2016 13:02:52 +0000 (13:02 +0000)]
bcm: Make RASPBERRYPI_POWER depend on PM
popcornmix [Tue, 5 Apr 2016 18:40:12 +0000 (19:40 +0100)]
reboot: Use power off rather than busy spinning when halt is requested
Noralf Trønnes [Fri, 7 Oct 2016 14:50:59 +0000 (16:50 +0200)]
watchdog: bcm2835: Support setting reboot partition
The Raspberry Pi firmware looks at the RSTS register to know which
partition to boot from. The reboot syscall command
LINUX_REBOOT_CMD_RESTART2 supports passing in a string argument.
Add support for passing in a partition number 0..63 to boot from.
Partition 63 is a special partiton indicating halt.
If the partition doesn't exist, the firmware falls back to partition 0.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Phil Elwell [Wed, 15 Jun 2016 15:48:41 +0000 (16:48 +0100)]
rtc: Add SPI alias for pcf2123 driver
Without this alias, Device Tree won't cause the driver
to be loaded.
See: https://github.com/raspberrypi/linux/pull/1510
popcornmix [Mon, 25 Jan 2016 17:25:12 +0000 (17:25 +0000)]
firmware: Updated mailbox header
Noralf Trønnes [Sat, 3 Oct 2015 20:22:55 +0000 (22:22 +0200)]
dmaengine: bcm2835: Load driver early and support legacy API
Load driver early since at least bcm2708_fb doesn't support deferred
probing and even if it did, we don't want the video driver deferred.
Support the legacy DMA API which is needed by bcm2708_fb.
Don't mask out channel 2.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Phil Elwell [Tue, 14 Jul 2015 09:26:09 +0000 (10:26 +0100)]
spi: spidev: Completely disable the spidev warning
An alternative strategy would be to use "rpi,spidev" instead, but that
would require many Raspberry Pi Device Tree changes.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Noralf Trønnes [Fri, 23 Oct 2015 14:26:55 +0000 (16:26 +0200)]
irqchip: irq-bcm2835: Add 2836 FIQ support
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Noralf Trønnes [Fri, 12 Jun 2015 17:01:05 +0000 (19:01 +0200)]
irqchip: bcm2835: Add FIQ support
Add a duplicate irq range with an offset on the hwirq's so the
driver can detect that enable_fiq() is used.
Tested with downstream dwc_otg USB controller driver.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Phil Elwell [Thu, 9 Feb 2017 14:33:30 +0000 (14:33 +0000)]
irq-bcm2836: Avoid "Invalid trigger warning"
Initialise the level for each IRQ to avoid a warning from the
arm arch timer code.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Fri, 13 Mar 2015 12:43:36 +0000 (12:43 +0000)]
Protect __release_resource against resources without parents
Without this patch, removing a device tree overlay can crash here.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
popcornmix [Tue, 26 Mar 2013 17:26:38 +0000 (17:26 +0000)]
Allow mac address to be set in smsc95xx
Signed-off-by: popcornmix <popcornmix@gmail.com>
Sam Nazarko [Fri, 1 Apr 2016 16:27:21 +0000 (17:27 +0100)]
smsc95xx: Experimental: Enable turbo_mode and packetsize=2560 by default
See: http://forum.kodi.tv/showthread.php?tid=285288
Steve Glendinning [Thu, 19 Feb 2015 18:47:12 +0000 (18:47 +0000)]
smsx95xx: fix crimes against truesize
smsc95xx is adjusting truesize when it shouldn't, and following a recent patch from Eric this is now triggering warnings.
This patch stops smsc95xx from changing truesize.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Phil Elwell [Tue, 3 Nov 2020 11:49:53 +0000 (11:49 +0000)]
Revert "mailbox: avoid timer start from callback"
This reverts commit
c7dacf5b0f32957b24ef29df1207dc2cd8307743.
The Pi 400 shutdown/poweroff mechanism relies on being able to set
a GPIO on the expander in the pm_power_off handler, something that
requires two mailbox calls - GET_GPIO_STATE and SET_GPIO_STATE. A
recent kernel change introduces a reasonable possibility that the
GET call doesn't completes, and bisecting led to a commit from
October that changes the timer usage of the mailbox.
My theory is that there is a race condition in the new code that breaks
the poll timer, but that it normally goes unnoticed because subsequent
mailbox activity wakes it up again. The power-off mailbox calls happen
at a time when other subsystems have been shut down, so if one of them
fails then there is nothing to allow it to recover.
See: https://github.com/raspberrypi/linux/issues/3941
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Mon, 20 Apr 2020 12:41:10 +0000 (13:41 +0100)]
Revert "spi: spidev: Fix CS polarity if GPIO descriptors are used"
This reverts commit
83b2a8fe43bda0c11981ad6afa5dd0104d78be28.
popcornmix [Fri, 15 Mar 2019 21:11:10 +0000 (21:11 +0000)]
Revert "staging: bcm2835-audio: Drop DT dependency"
This reverts commit
b7491a9fca2dc2535b9dc922550a37c5baae9d3d.
Phil Elwell [Mon, 29 Oct 2018 14:45:45 +0000 (14:45 +0000)]
Revert "rtc: pcf8523: properly handle oscillator stop bit"
This reverts commit
ede44c908d44b166a5b6bd7caacd105c2ff5a70f.
See: https://github.com/raspberrypi/firmware/issues/1065
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Dan Pasanen [Thu, 21 Sep 2017 14:55:42 +0000 (09:55 -0500)]
arm: partially revert
702b94bff3c50542a6e4ab9a4f4cef093262fe65
* Re-expose some dmi APIs for use in VCSM
Greg Kroah-Hartman [Wed, 27 Jan 2021 10:55:30 +0000 (11:55 +0100)]
Linux 5.10.11
Tested-by: Pavel Machek (CIP) <pavel@denx.de>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210126094313.589480033@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Tue, 26 Jan 2021 18:39:46 +0000 (10:39 -0800)]
Revert "mm: fix initialization of struct page for holes in memory layout"
commit
377bf660d07a47269510435d11f3b65d53edca20 upstream.
This reverts commit
d3921cb8be29ce5668c64e23ffdaeec5f8c69399.
Chris Wilson reports that it causes boot problems:
"We have half a dozen or so different machines in CI that are silently
failing to boot, that we believe is bisected to this patch"
and the CI team confirmed that a revert fixed the issues.
The cause is unknown for now, so let's revert it.
Link: https://lore.kernel.org/lkml/161160687463.28991.354987542182281928@build.alporthouse.com/
Reported-and-tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mike Rapoport [Sun, 24 Jan 2021 05:01:02 +0000 (21:01 -0800)]
mm: fix initialization of struct page for holes in memory layout
commit
d3921cb8be29ce5668c64e23ffdaeec5f8c69399 upstream.
There could be struct pages that are not backed by actual physical
memory. This can happen when the actual memory bank is not a multiple
of SECTION_SIZE or when an architecture does not register memory holes
reserved by the firmware as memblock.memory.
Such pages are currently initialized using init_unavailable_mem()
function that iterates through PFNs in holes in memblock.memory and if
there is a struct page corresponding to a PFN, the fields if this page
are set to default values and the page is marked as Reserved.
init_unavailable_mem() does not take into account zone and node the page
belongs to and sets both zone and node links in struct page to zero.
On a system that has firmware reserved holes in a zone above ZONE_DMA,
for instance in a configuration below:
# grep -A1 E820 /proc/iomem
7a17b000-
7a216fff : Unknown E820 type
7a217000-
7bffffff : System RAM
unset zone link in struct page will trigger
VM_BUG_ON_PAGE(!zone_spans_pfn(page_zone(page), pfn), page);
because there are pages in both ZONE_DMA32 and ZONE_DMA (unset zone link
in struct page) in the same pageblock.
Update init_unavailable_mem() to use zone constraints defined by an
architecture to properly setup the zone link and use node ID of the
adjacent range in memblock.memory to set the node link.
Link: https://lkml.kernel.org/r/20210111194017.22696-3-rppt@kernel.org
Fixes:
73a6e474cb37 ("mm: memmap_init: iterate over memblock regions rather that check each PFN")
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Reported-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Hildenbrand <david@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Qian Cai <cai@lca.pw>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sami Tolvanen [Mon, 25 Jan 2021 19:09:25 +0000 (11:09 -0800)]
Commit
9bb48c82aced ("tty: implement write_iter") converted the tty layer to use write_iter. Fix the redirected_tty_write declaration also in n_tty and change the comparisons to use write_iter instead of write. also in n_tty and change the comparisons to use write_iter instead of write.
commit
9f12e37cae44a96132fc3031535a0b165486941a upstream.
[ Also moved the declaration of redirected_tty_write() to the proper
location in a header file. The reason for the bug was the bogus extern
declaration in n_tty.c silently not matching the changed definition in
tty_io.c, and because it wasn't in a shared header file, there was no
cross-checking of the declaration.
Sami noticed because Clang's Control Flow Integrity checking ended up
incidentally noticing the inconsistent declaration. - Linus ]
Fixes:
9bb48c82aced ("tty: implement write_iter")
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johannes Berg [Mon, 25 Jan 2021 09:16:15 +0000 (10:16 +0100)]
fs/pipe: allow sendfile() to pipe again
commit
f8ad8187c3b536ee2b10502a8340c014204a1af0 upstream.
After commit
36e2c7421f02 ("fs: don't allow splice read/write
without explicit ops") sendfile() could no longer send data
from a real file to a pipe, breaking for example certain cgit
setups (e.g. when running behind fcgiwrap), because in this
case cgit will try to do exactly this: sendfile() to a pipe.
Fix this by using iter_file_splice_write for the splice_write
method of pipes, as suggested by Christoph.
Cc: stable@vger.kernel.org
Fixes:
36e2c7421f02 ("fs: don't allow splice read/write without explicit ops")
Suggested-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Martin Kepplinger [Mon, 28 Dec 2020 12:03:02 +0000 (14:03 +0200)]
interconnect: imx8mq: Use icc_sync_state
commit
67288f74d4837b82ef937170da3389b0779c17be upstream.
Add the icc_sync_state callback to notify the framework when consumers
are probed and the bandwidth doesn't have to be kept at maximum anymore.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Suggested-by: Georgi Djakov <georgi.djakov@linaro.org>
Fixes:
7d3b0b0d8184 ("interconnect: qcom: Use icc_sync_state")
Link: https://lore.kernel.org/r/20201210100906.18205-6-martin.kepplinger@puri.sm
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christoph Hellwig [Wed, 20 Jan 2021 20:46:31 +0000 (21:46 +0100)]
kernfs: wire up ->splice_read and ->splice_write
commit
f2d6c2708bd84ca953fa6b6ca5717e79eb0140c7 upstream.
Wire up the splice_read and splice_write methods to the default
helpers using ->read_iter and ->write_iter now that those are
implemented for kernfs. This restores support to use splice and
sendfile on kernfs files.
Fixes:
36e2c7421f02 ("fs: don't allow splice read/write without explicit ops")
Reported-by: Siddharth Gupta <sidgup@codeaurora.org>
Tested-by: Siddharth Gupta <sidgup@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210120204631.274206-4-hch@lst.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christoph Hellwig [Wed, 20 Jan 2021 20:46:30 +0000 (21:46 +0100)]
kernfs: implement ->write_iter
commit
cc099e0b399889c6485c88368b19824b087c9f8c upstream.
Switch kernfs to implement the write_iter method instead of plain old
write to prepare to supporting splice and sendfile again.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210120204631.274206-3-hch@lst.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christoph Hellwig [Wed, 20 Jan 2021 20:46:29 +0000 (21:46 +0100)]
kernfs: implement ->read_iter
commit
4eaad21a6ac9865df7f31983232ed5928450458d upstream.
Switch kernfs to implement the read_iter method instead of plain old
read to prepare to supporting splice and sendfile again.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210120204631.274206-2-hch@lst.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KP Singh [Tue, 12 Jan 2021 07:55:24 +0000 (07:55 +0000)]
bpf: Local storage helpers should check nullness of owner ptr passed
commit
1a9c72ad4c26821e215a396167c14959cf24a7f1 upstream.
The verifier allows ARG_PTR_TO_BTF_ID helper arguments to be NULL, so
helper implementations need to check this before dereferencing them.
This was already fixed for the socket storage helpers but not for task
and inode.
The issue can be reproduced by attaching an LSM program to
inode_rename hook (called when moving files) which tries to get the
inode of the new file without checking for its nullness and then trying
to move an existing file to a new path:
mv existing_file new_file_does_not_exist
The report including the sample program and the steps for reproducing
the bug:
https://lore.kernel.org/bpf/CANaYP3HWkH91SN=wTNO9FL_2ztHfqcXKX38SSE-JJ2voh+vssw@mail.gmail.com
Fixes:
4cf1bc1f1045 ("bpf: Implement task local storage")
Fixes:
8ea636848aca ("bpf: Implement bpf_local_storage for inodes")
Reported-by: Gilad Reti <gilad.reti@gmail.com>
Signed-off-by: KP Singh <kpsingh@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20210112075525.256820-3-kpsingh@kernel.org
[ just take 1/2 of this patch for 5.10.y - gregkh ]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Anshuman Gupta [Mon, 11 Jan 2021 08:11:03 +0000 (13:41 +0530)]
drm/i915/hdcp: Get conn while content_type changed
commit
8662e1119a7d1baa1b2001689b2923e9050754bd upstream.
Get DRM connector reference count while scheduling a prop work
to avoid any possible destroy of DRM connector when it is in
DRM_CONNECTOR_REGISTERED state.
Fixes:
a6597faa2d59 ("drm/i915: Protect workers against disappearing connectors")
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-3-anshuman.gupta@intel.com
(cherry picked from commit
b3c6661aad979ec3d4f5675cf3e6a35828607d6a)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kai-Heng Feng [Tue, 12 Jan 2021 18:11:25 +0000 (02:11 +0800)]
ASoC: SOF: Intel: hda: Avoid checking jack on system suspend
commit
ef4d764c99f792b725d4754a3628830f094f5c58 upstream.
System takes a very long time to suspend after commit
215a22ed31a1
("ALSA: hda: Refactor codec PM to use direct-complete optimization"):
[ 90.065964] PM: suspend entry (s2idle)
[ 90.067337] Filesystems sync: 0.001 seconds
[ 90.185758] Freezing user space processes ... (elapsed 0.002 seconds) done.
[ 90.188713] OOM killer disabled.
[ 90.188714] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 90.190024] printk: Suspending console(s) (use no_console_suspend to debug)
[ 90.904912] intel_pch_thermal 0000:00:12.0: CPU-PCH is cool [49C], continue to suspend
[ 321.262505] snd_hda_codec_realtek ehdaudio0D0: Unable to sync register 0x2b8000. -5
[ 328.426919] snd_hda_codec_realtek ehdaudio0D0: Unable to sync register 0x2b8000. -5
[ 329.490933] ACPI: EC: interrupt blocked
That commit keeps the codec suspended during the system suspend. However,
mute/micmute LED will clear codec's direct-complete flag by
dpm_clear_superiors_direct_complete().
This doesn't play well with SOF driver. When its runtime resume is
called for system suspend, hda_codec_jack_check() schedules
jackpoll_work which uses snd_hdac_is_power_on() to check whether codec
is suspended. Because the direct-complete path isn't taken,
pm_runtime_disable() isn't called so snd_hdac_is_power_on() returns
false and jackpoll continues to run, and snd_hda_power_up_pm() cannot
power up an already suspended codec in multiple attempts, causes the
long delay on system suspend:
if (dev->power.direct_complete) {
if (pm_runtime_status_suspended(dev)) {
pm_runtime_disable(dev);
if (pm_runtime_status_suspended(dev)) {
pm_dev_dbg(dev, state, "direct-complete ");
goto Complete;
}
pm_runtime_enable(dev);
}
dev->power.direct_complete = false;
}
When direct-complete path is taken, snd_hdac_is_power_on() returns true
and hda_jackpoll_work() is skipped by accident. So this is still not
correct.
If we were to use snd_hdac_is_power_on() in system PM path,
pm_runtime_status_suspended() should be used instead of
pm_runtime_suspended(), otherwise pm_runtime_{enable,disable}() may
change the outcome of snd_hdac_is_power_on().
Because devices suspend in reverse order (i.e. child first), it doesn't
make much sense to resume an already suspended codec from audio
controller. So avoid the issue by making sure jackpoll isn't used in
system PM process.
Fixes:
215a22ed31a1 ("ALSA: hda: Refactor codec PM to use direct-complete optimization")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210112181128.1229827-3-kai.heng.feng@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kuniyuki Iwashima [Mon, 18 Jan 2021 05:59:20 +0000 (14:59 +0900)]
tcp: Fix potential use-after-free due to double kfree()
commit
c89dffc70b340780e5b933832d8c3e045ef3791e upstream.
Receiving ACK with a valid SYN cookie, cookie_v4_check() allocates struct
request_sock and then can allocate inet_rsk(req)->ireq_opt. After that,
tcp_v4_syn_recv_sock() allocates struct sock and copies ireq_opt to
inet_sk(sk)->inet_opt. Normally, tcp_v4_syn_recv_sock() inserts the full
socket into ehash and sets NULL to ireq_opt. Otherwise,
tcp_v4_syn_recv_sock() has to reset inet_opt by NULL and free the full
socket.
The commit
01770a1661657 ("tcp: fix race condition when creating child
sockets from syncookies") added a new path, in which more than one cores
create full sockets for the same SYN cookie. Currently, the core which
loses the race frees the full socket without resetting inet_opt, resulting
in that both sock_put() and reqsk_put() call kfree() for the same memory:
sock_put
sk_free
__sk_free
sk_destruct
__sk_destruct
sk->sk_destruct/inet_sock_destruct
kfree(rcu_dereference_protected(inet->inet_opt, 1));
reqsk_put
reqsk_free
__reqsk_free
req->rsk_ops->destructor/tcp_v4_reqsk_destructor
kfree(rcu_dereference_protected(inet_rsk(req)->ireq_opt, 1));
Calling kmalloc() between the double kfree() can lead to use-after-free, so
this patch fixes it by setting NULL to inet_opt before sock_put().
As a side note, this kind of issue does not happen for IPv6. This is
because tcp_v6_syn_recv_sock() clones both ipv6_opt and pktopts which
correspond to ireq_opt in IPv4.
Fixes:
01770a166165 ("tcp: fix race condition when creating child sockets from syncookies")
CC: Ricardo Dias <rdias@singlestore.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Reviewed-by: Benjamin Herrenschmidt <benh@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210118055920.82516-1-kuniyu@amazon.co.jp
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hyunwook (Wooky) Baek [Sun, 10 Jan 2021 07:11:02 +0000 (23:11 -0800)]
x86/sev-es: Handle string port IO to kernel memory properly
commit
7024f60d655272bd2ca1d3a4c9e0a63319b1eea1 upstream.
Don't assume dest/source buffers are userspace addresses when manually
copying data for string I/O or MOVS MMIO, as {get,put}_user() will fail
if handed a kernel address and ultimately lead to a kernel panic.
When invoking INSB/OUTSB instructions in kernel space in a
SEV-ES-enabled VM, the kernel crashes with the following message:
"SEV-ES: Unsupported exception in #VC instruction emulation - can't continue"
Handle that case properly.
[ bp: Massage commit message. ]
Fixes:
f980f9c31a92 ("x86/sev-es: Compile early handler code into kernel image")
Signed-off-by: Hyunwook (Wooky) Baek <baekhw@google.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: David Rientjes <rientjes@google.com>
Link: https://lkml.kernel.org/r/20210110071102.2576186-1-baekhw@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pan Bian [Wed, 20 Jan 2021 04:44:23 +0000 (20:44 -0800)]
net: systemport: free dev before on error path
commit
0c630a66bf10991b0ef13d27c93d7545e692ef5b upstream.
On the error path, it should goto the error handling label to free
allocated memory rather than directly return.
Fixes:
31bc72d97656 ("net: systemport: fetch and use clock resources")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210120044423.1704-1-bianpan2016@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Thu, 21 Jan 2021 18:04:27 +0000 (10:04 -0800)]
tty: fix up hung_up_tty_write() conversion
commit
17749851eb9ca2298e7c3b81aae4228961b36f28 upstream.
In commit "tty: implement write_iter", I left the write_iter conversion
of the hung up tty case alone, because I incorrectly thought it didn't
matter.
Jiri showed me the errors of my ways, and pointed out the problems with
that incomplete conversion. Fix it all up.
Reported-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/CAHk-=wh+-rGsa=xruEWdg_fJViFG8rN9bpLrfLz=_yBYh2tBhA@mail.gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Tue, 19 Jan 2021 19:41:16 +0000 (11:41 -0800)]
tty: implement write_iter
commit
9bb48c82aced07698a2d08ee0f1475a6c4f6b266 upstream.
This makes the tty layer use the .write_iter() function instead of the
traditional .write() functionality.
That allows writev(), but more importantly also makes it possible to
enable .splice_write() for ttys, reinstating the "splice to tty"
functionality that was lost in commit
36e2c7421f02 ("fs: don't allow
splice read/write without explicit ops").
Fixes:
36e2c7421f02 ("fs: don't allow splice read/write without explicit ops")
Reported-by: Oliver Giles <ohw.giles@gmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Zijlstra [Wed, 6 Jan 2021 14:36:21 +0000 (15:36 +0100)]
x86/sev: Fix nonistr violation
commit
a1d5c98aac33a5a0004ecf88905dcc261c52f988 upstream.
When the compiler fails to inline, it violates nonisntr:
vmlinux.o: warning: objtool: __sev_es_nmi_complete()+0xc7: call to sev_es_wr_ghcb_msr() leaves .noinstr.text section
Fixes:
4ca68e023b11 ("x86/sev-es: Handle NMI State")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210106144017.532902065@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Douglas Anderson [Fri, 15 Jan 2021 03:16:24 +0000 (19:16 -0800)]
pinctrl: qcom: Don't clear pending interrupts when enabling
commit
cf9d052aa6005f1e8dfaf491d83bf37f368af69e upstream.
In Linux, if a driver does disable_irq() and later does enable_irq()
on its interrupt, I believe it's expecting these properties:
* If an interrupt was pending when the driver disabled then it will
still be pending after the driver re-enables.
* If an edge-triggered interrupt comes in while an interrupt is
disabled it should assert when the interrupt is re-enabled.
If you think that the above sounds a lot like the disable_irq() and
enable_irq() are supposed to be masking/unmasking the interrupt
instead of disabling/enabling it then you've made an astute
observation. Specifically when talking about interrupts, "mask"
usually means to stop posting interrupts but keep tracking them and
"disable" means to fully shut off interrupt detection. It's
unfortunate that this is so confusing, but presumably this is all the
way it is for historical reasons.
Perhaps more confusing than the above is that, even though clients of
IRQs themselves don't have a way to request mask/unmask
vs. disable/enable calls, IRQ chips themselves can implement both.
...and yet more confusing is that if an IRQ chip implements
disable/enable then they will be called when a client driver calls
disable_irq() / enable_irq().
It does feel like some of the above could be cleared up. However,
without any other core interrupt changes it should be clear that when
an IRQ chip gets a request to "disable" an IRQ that it has to treat it
like a mask of that IRQ.
In any case, after that long interlude you can see that the "unmask
and clear" can break things. Maulik tried to fix it so that we no
longer did "unmask and clear" in commit
71266d9d3936 ("pinctrl: qcom:
Move clearing pending IRQ to .irq_request_resources callback"), but it
only handled the PDC case and it had problems (it caused
sc7180-trogdor devices to fail to suspend). Let's fix.
>From my understanding the source of the phantom interrupt in the
were these two things:
1. One that could have been introduced in msm_gpio_irq_set_type()
(only for the non-PDC case).
2. Edges could have been detected when a GPIO was muxed away.
Fixing case #1 is easy. We can just add a clear in
msm_gpio_irq_set_type().
Fixing case #2 is harder. Let's use a concrete example. In
sc7180-trogdor.dtsi we configure the uart3 to have two pinctrl states,
sleep and default, and mux between the two during runtime PM and
system suspend (see geni_se_resources_{on,off}() for more
details). The difference between the sleep and default state is that
the RX pin is muxed to a GPIO during sleep and muxed to the UART
otherwise.
As per Qualcomm, when we mux the pin over to the UART function the PDC
(or the non-PDC interrupt detection logic) is still watching it /
latching edges. These edges don't cause interrupts because the
current code masks the interrupt unless we're entering suspend.
However, as soon as we enter suspend we unmask the interrupt and it's
counted as a wakeup.
Let's deal with the problem like this:
* When we mux away, we'll mask our interrupt. This isn't necessary in
the above case since the client already masked us, but it's a good
idea in general.
* When we mux back will clear any interrupts and unmask.
Fixes:
4b7618fdc7e6 ("pinctrl: qcom: Add irq_enable callback for msm gpio")
Fixes:
71266d9d3936 ("pinctrl: qcom: Move clearing pending IRQ to .irq_request_resources callback")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210114191601.v7.4.I7cf3019783720feb57b958c95c2b684940264cd1@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Douglas Anderson [Fri, 15 Jan 2021 03:16:23 +0000 (19:16 -0800)]
pinctrl: qcom: Properly clear "intr_ack_high" interrupts when unmasking
commit
a95881d6aa2c000e3649f27a1a7329cf356e6bb3 upstream.
In commit
4b7618fdc7e6 ("pinctrl: qcom: Add irq_enable callback for
msm gpio") we tried to Ack interrupts during unmask. However, that
patch forgot to check "intr_ack_high" so, presumably, it only worked
for a certain subset of SoCs.
Let's add a small accessor so we don't need to open-code the logic in
both places.
This was found by code inspection. I don't have any access to the
hardware in question nor software that needs the Ack during unmask.
Fixes:
4b7618fdc7e6 ("pinctrl: qcom: Add irq_enable callback for msm gpio")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210114191601.v7.3.I32d0f4e174d45363b49ab611a13c3da8f1e87d0f@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Douglas Anderson [Fri, 15 Jan 2021 03:16:22 +0000 (19:16 -0800)]
pinctrl: qcom: No need to read-modify-write the interrupt status
commit
4079d35fa4fca4ee0ffd66968312fc86a5e8c290 upstream.
When the Qualcomm pinctrl driver wants to Ack an interrupt, it does a
read-modify-write on the interrupt status register. On some SoCs it
makes sure that the status bit is 1 to "Ack" and on others it makes
sure that the bit is 0 to "Ack". Presumably the first type of
interrupt controller is a "write 1 to clear" type register and the
second just let you directly set the interrupt status register.
As far as I can tell from scanning structure definitions, the
interrupt status bit is always in a register by itself. Thus with
both types of interrupt controllers it is safe to "Ack" interrupts
without doing a read-modify-write. We can do a simple write.
It should be noted that if the interrupt status bit _was_ ever in a
register with other things (like maybe status bits for other GPIOs):
a) For "write 1 clear" type controllers then read-modify-write would
be totally wrong because we'd accidentally end up clearing
interrupts we weren't looking at.
b) For "direct set" type controllers then read-modify-write would also
be wrong because someone setting one of the other bits in the
register might accidentally clear (or set) our interrupt.
I say this simply to show that the current read-modify-write doesn't
provide any sort of "future proofing" of the code. In fact (for
"write 1 clear" controllers) the new code is slightly more "future
proof" since it would allow more than one interrupt status bits to
share a register.
NOTE: this code fixes no bugs--it simply avoids an extra register
read.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210114191601.v7.2.I3635de080604e1feda770591c5563bd6e63dd39d@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Douglas Anderson [Fri, 15 Jan 2021 03:16:21 +0000 (19:16 -0800)]
pinctrl: qcom: Allow SoCs to specify a GPIO function that's not 0
commit
a82e537807d5c85706cd4c16fd2de77a8495dc8d upstream.
There's currently a comment in the code saying function 0 is GPIO.
Instead of hardcoding it, let's add a member where an SoC can specify
it. No known SoCs use a number other than 0, but this just makes the
code clearer. NOTE: no SoC code needs to be updated since we can rely
on zero-initialization.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210114191601.v7.1.I3ad184e3423d8e479bc3e86f5b393abb1704a1d1@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oleksandr Mazur [Tue, 19 Jan 2021 08:53:33 +0000 (10:53 +0200)]
net: core: devlink: use right genl user_ptr when handling port param get/set
commit
7e238de8283acd32c26c2bc2a50672d0ea862ff7 upstream.
Fix incorrect user_ptr dereferencing when handling port param get/set:
idx [0] stores the 'struct devlink' pointer;
idx [1] stores the 'struct devlink_port' pointer;
Fixes:
637989b5d77e ("devlink: Always use user_ptr[0] for devlink and simplify post_doit")
CC: Parav Pandit <parav@mellanox.com>
Signed-off-by: Oleksandr Mazur <oleksandr.mazur@plvision.eu>
Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu>
Link: https://lore.kernel.org/r/20210119085333.16833-1-vadym.kochan@plvision.eu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alban Bedel [Tue, 19 Jan 2021 14:06:38 +0000 (15:06 +0100)]
net: mscc: ocelot: Fix multicast to the CPU port
commit
584b7cfcdc7d6d416a9d6fece9516764bd977d2e upstream.
Multicast entries in the MAC table use the high bits of the MAC
address to encode the ports that should get the packets. But this port
mask does not work for the CPU port, to receive these packets on the
CPU port the MAC_CPU_COPY flag must be set.
Because of this IPv6 was effectively not working because neighbor
solicitations were never received. This was not apparent before commit
9403c158 (net: mscc: ocelot: support IPv4, IPv6 and plain Ethernet mdb
entries) as the IPv6 entries were broken so all incoming IPv6
multicast was then treated as unknown and flooded on all ports.
To fix this problem rework the ocelot_mact_learn() to set the
MAC_CPU_COPY flag when a multicast entry that target the CPU port is
added. For this we have to read back the ports endcoded in the pseudo
MAC address by the caller. It is not a very nice design but that avoid
changing the callers and should make backporting easier.
Signed-off-by: Alban Bedel <alban.bedel@aerq.com>
Fixes:
9403c158b872 ("net: mscc: ocelot: support IPv4, IPv6 and plain Ethernet mdb entries")
Link: https://lore.kernel.org/r/20210119140638.203374-1-alban.bedel@aerq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enke Chen [Fri, 15 Jan 2021 22:30:58 +0000 (14:30 -0800)]
tcp: fix TCP_USER_TIMEOUT with zero window
commit
9d9b1ee0b2d1c9e02b2338c4a4b0a062d2d3edac upstream.
The TCP session does not terminate with TCP_USER_TIMEOUT when data
remain untransmitted due to zero window.
The number of unanswered zero-window probes (tcp_probes_out) is
reset to zero with incoming acks irrespective of the window size,
as described in tcp_probe_timer():
RFC 1122 4.2.2.17 requires the sender to stay open indefinitely
as long as the receiver continues to respond probes. We support
this by default and reset icsk_probes_out with incoming ACKs.
This counter, however, is the wrong one to be used in calculating the
duration that the window remains closed and data remain untransmitted.
Thanks to Jonathan Maxwell <jmaxwell37@gmail.com> for diagnosing the
actual issue.
In this patch a new timestamp is introduced for the socket in order to
track the elapsed time for the zero-window probes that have not been
answered with any non-zero window ack.
Fixes:
9721e709fa68 ("tcp: simplify window probe aborting on USER_TIMEOUT")
Reported-by: William McCall <william.mccall@gmail.com>
Co-developed-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Enke Chen <enchen@paloaltonetworks.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210115223058.GA39267@localhost.localdomain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Tue, 19 Jan 2021 16:49:00 +0000 (08:49 -0800)]
tcp: do not mess with cloned skbs in tcp_add_backlog()
commit
b160c28548bc0a87cbd16d5af6d3edcfd70b8c9a upstream.
Heiner Kallweit reported that some skbs were sent with
the following invalid GSO properties :
- gso_size > 0
- gso_type == 0
This was triggerring a WARN_ON_ONCE() in rtl8169_tso_csum_v2.
Juerg Haefliger was able to reproduce a similar issue using
a lan78xx NIC and a workload mixing TCP incoming traffic
and forwarded packets.
The problem is that tcp_add_backlog() is writing
over gso_segs and gso_size even if the incoming packet will not
be coalesced to the backlog tail packet.
While skb_try_coalesce() would bail out if tail packet is cloned,
this overwriting would lead to corruptions of other packets
cooked by lan78xx, sharing a common super-packet.
The strategy used by lan78xx is to use a big skb, and split
it into all received packets using skb_clone() to avoid copies.
The drawback of this strategy is that all the small skb share a common
struct skb_shared_info.
This patch rewrites TCP gso_size/gso_segs handling to only
happen on the tail skb, since skb_try_coalesce() made sure
it was not cloned.
Fixes:
4f693b55c3d2 ("tcp: implement coalescing on backlog queue")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Bisected-by: Juerg Haefliger <juergh@canonical.com>
Tested-by: Juerg Haefliger <juergh@canonical.com>
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209423
Link: https://lore.kernel.org/r/20210119164900.766957-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter [Tue, 19 Jan 2021 14:48:03 +0000 (17:48 +0300)]
net: dsa: b53: fix an off by one in checking "vlan->vid"
commit
8e4052c32d6b4b39c1e13c652c7e33748d447409 upstream.
The > comparison should be >= to prevent accessing one element beyond
the end of the dev->vlans[] array in the caller function, b53_vlan_add().
The "dev->vlans" array is allocated in the b53_switch_init() function
and it has "dev->num_vlans" elements.
Fixes:
a2482d2ce349 ("net: dsa: b53: Plug in VLAN support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/YAbxI97Dl/pmBy5V@mwanda
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tariq Toukan [Sun, 17 Jan 2021 15:15:38 +0000 (17:15 +0200)]
net: Disable NETIF_F_HW_TLS_RX when RXCSUM is disabled
commit
a3eb4e9d4c9218476d05c52dfd2be3d6fdce6b91 upstream.
With NETIF_F_HW_TLS_RX packets are decrypted in HW. This cannot be
logically done when RXCSUM offload is off.
Fixes:
14136564c8ee ("net: Add TLS RX offload feature")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Boris Pismenny <borisp@nvidia.com>
Link: https://lore.kernel.org/r/20210117151538.9411-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vladimir Oltean [Mon, 18 Jan 2021 13:52:10 +0000 (15:52 +0200)]
net: mscc: ocelot: allow offloading of bridge on top of LAG
commit
79267ae22615496655feee2db0848f6786bcf67a upstream.
The blamed commit was too aggressive, and it made ocelot_netdevice_event
react only to network interface events emitted for the ocelot switch
ports.
In fact, only the PRECHANGEUPPER should have had that check.
When we ignore all events that are not for us, we miss the fact that the
upper of the LAG changes, and the bonding interface gets enslaved to a
bridge. This is an operation we could offload under certain conditions.
Fixes:
7afb3e575e5a ("net: mscc: ocelot: don't handle netdev events for other netdevs")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210118135210.2666246-1-olteanv@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Matteo Croce [Fri, 15 Jan 2021 18:42:09 +0000 (19:42 +0100)]
ipv6: set multicast flag on the multicast route
commit
ceed9038b2783d14e0422bdc6fd04f70580efb4c upstream.
The multicast route ff00::/8 is created with type RTN_UNICAST:
$ ip -6 -d route
unicast ::1 dev lo proto kernel scope global metric 256 pref medium
unicast fe80::/64 dev eth0 proto kernel scope global metric 256 pref medium
unicast ff00::/8 dev eth0 proto kernel scope global metric 256 pref medium
Set the type to RTN_MULTICAST which is more appropriate.
Fixes:
e8478e80e5a7 ("net/ipv6: Save route type in rt6_info")
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Thu, 14 Jan 2021 16:06:37 +0000 (08:06 -0800)]
net_sched: reject silly cell_log in qdisc_get_rtab()
commit
e4bedf48aaa5552bc1f49703abd17606e7e6e82a upstream.
iproute2 probably never goes beyond 8 for the cell exponent,
but stick to the max shift exponent for signed 32bit.
UBSAN reported:
UBSAN: shift-out-of-bounds in net/sched/sch_api.c:389:22
shift exponent 130 is too large for 32-bit type 'int'
CPU: 1 PID: 8450 Comm: syz-executor586 Not tainted 5.11.0-rc3-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x183/0x22e lib/dump_stack.c:120
ubsan_epilogue lib/ubsan.c:148 [inline]
__ubsan_handle_shift_out_of_bounds+0x432/0x4d0 lib/ubsan.c:395
__detect_linklayer+0x2a9/0x330 net/sched/sch_api.c:389
qdisc_get_rtab+0x2b5/0x410 net/sched/sch_api.c:435
cbq_init+0x28f/0x12c0 net/sched/sch_cbq.c:1180
qdisc_create+0x801/0x1470 net/sched/sch_api.c:1246
tc_modify_qdisc+0x9e3/0x1fc0 net/sched/sch_api.c:1662
rtnetlink_rcv_msg+0xb1d/0xe60 net/core/rtnetlink.c:5564
netlink_rcv_skb+0x1f0/0x460 net/netlink/af_netlink.c:2494
netlink_unicast_kernel net/netlink/af_netlink.c:1304 [inline]
netlink_unicast+0x7de/0x9b0 net/netlink/af_netlink.c:1330
netlink_sendmsg+0xaa6/0xe90 net/netlink/af_netlink.c:1919
sock_sendmsg_nosec net/socket.c:652 [inline]
sock_sendmsg net/socket.c:672 [inline]
____sys_sendmsg+0x5a2/0x900 net/socket.c:2345
___sys_sendmsg net/socket.c:2399 [inline]
__sys_sendmsg+0x319/0x400 net/socket.c:2432
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: Cong Wang <cong.wang@bytedance.com>
Link: https://lore.kernel.org/r/20210114160637.1660597-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Thu, 14 Jan 2021 18:52:29 +0000 (10:52 -0800)]
net_sched: avoid shift-out-of-bounds in tcindex_set_parms()
commit
bcd0cf19ef8258ac31b9a20248b05c15a1f4b4b0 upstream.
tc_index being 16bit wide, we need to check that TCA_TCINDEX_SHIFT
attribute is not silly.
UBSAN: shift-out-of-bounds in net/sched/cls_tcindex.c:260:29
shift exponent 255 is too large for 32-bit type 'int'
CPU: 0 PID: 8516 Comm: syz-executor228 Not tainted 5.10.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x107/0x163 lib/dump_stack.c:120
ubsan_epilogue+0xb/0x5a lib/ubsan.c:148
__ubsan_handle_shift_out_of_bounds.cold+0xb1/0x181 lib/ubsan.c:395
valid_perfect_hash net/sched/cls_tcindex.c:260 [inline]
tcindex_set_parms.cold+0x1b/0x215 net/sched/cls_tcindex.c:425
tcindex_change+0x232/0x340 net/sched/cls_tcindex.c:546
tc_new_tfilter+0x13fb/0x21b0 net/sched/cls_api.c:2127
rtnetlink_rcv_msg+0x8b6/0xb80 net/core/rtnetlink.c:5555
netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2494
netlink_unicast_kernel net/netlink/af_netlink.c:1304 [inline]
netlink_unicast+0x533/0x7d0 net/netlink/af_netlink.c:1330
netlink_sendmsg+0x907/0xe40 net/netlink/af_netlink.c:1919
sock_sendmsg_nosec net/socket.c:652 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:672
____sys_sendmsg+0x6e8/0x810 net/socket.c:2336
___sys_sendmsg+0xf3/0x170 net/socket.c:2390
__sys_sendmsg+0xe5/0x1b0 net/socket.c:2423
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Link: https://lore.kernel.org/r/20210114185229.1742255-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Matteo Croce [Fri, 15 Jan 2021 18:42:08 +0000 (19:42 +0100)]
ipv6: create multicast route with RTPROT_KERNEL
commit
a826b04303a40d52439aa141035fca5654ccaccd upstream.
The ff00::/8 multicast route is created without specifying the fc_protocol
field, so the default RTPROT_BOOT value is used:
$ ip -6 -d route
unicast ::1 dev lo proto kernel scope global metric 256 pref medium
unicast fe80::/64 dev eth0 proto kernel scope global metric 256 pref medium
unicast ff00::/8 dev eth0 proto boot scope global metric 256 pref medium
As the documentation says, this value identifies routes installed during
boot, but the route is created when interface is set up.
Change the value to RTPROT_KERNEL which is a better value.
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guillaume Nault [Sat, 16 Jan 2021 10:44:22 +0000 (11:44 +0100)]
udp: mask TOS bits in udp_v4_early_demux()
commit
8d2b51b008c25240914984208b2ced57d1dd25a5 upstream.
udp_v4_early_demux() is the only function that calls
ip_mc_validate_source() with a TOS that hasn't been masked with
IPTOS_RT_MASK.
This results in different behaviours for incoming multicast UDPv4
packets, depending on if ip_mc_validate_source() is called from the
early-demux path (udp_v4_early_demux) or from the regular input path
(ip_route_input_noref).
ECN would normally not be used with UDP multicast packets, so the
practical consequences should be limited on that side. However,
IPTOS_RT_MASK is used to also masks the TOS' high order bits, to align
with the non-early-demux path behaviour.
Reproducer:
Setup two netns, connected with veth:
$ ip netns add ns0
$ ip netns add ns1
$ ip -netns ns0 link set dev lo up
$ ip -netns ns1 link set dev lo up
$ ip link add name veth01 netns ns0 type veth peer name veth10 netns ns1
$ ip -netns ns0 link set dev veth01 up
$ ip -netns ns1 link set dev veth10 up
$ ip -netns ns0 address add 192.0.2.10 peer 192.0.2.11/32 dev veth01
$ ip -netns ns1 address add 192.0.2.11 peer 192.0.2.10/32 dev veth10
In ns0, add route to multicast address 224.0.2.0/24 using source
address 198.51.100.10:
$ ip -netns ns0 address add 198.51.100.10/32 dev lo
$ ip -netns ns0 route add 224.0.2.0/24 dev veth01 src 198.51.100.10
In ns1, define route to 198.51.100.10, only for packets with TOS 4:
$ ip -netns ns1 route add 198.51.100.10/32 tos 4 dev veth10
Also activate rp_filter in ns1, so that incoming packets not matching
the above route get dropped:
$ ip netns exec ns1 sysctl -wq net.ipv4.conf.veth10.rp_filter=1
Now try to receive packets on 224.0.2.11:
$ ip netns exec ns1 socat UDP-RECVFROM:1111,ip-add-membership=224.0.2.11:veth10,ignoreeof -
In ns0, send packet to 224.0.2.11 with TOS 4 and ECT(0) (that is,
tos 6 for socat):
$ echo test0 | ip netns exec ns0 socat - UDP-DATAGRAM:224.0.2.11:1111,bind=:1111,tos=6
The "test0" message is properly received by socat in ns1, because
early-demux has no cached dst to use, so source address validation
is done by ip_route_input_mc(), which receives a TOS that has the
ECN bits masked.
Now send another packet to 224.0.2.11, still with TOS 4 and ECT(0):
$ echo test1 | ip netns exec ns0 socat - UDP-DATAGRAM:224.0.2.11:1111,bind=:1111,tos=6
The "test1" message isn't received by socat in ns1, because, now,
early-demux has a cached dst to use and calls ip_mc_validate_source()
immediately, without masking the ECN bits.
Fixes:
bc044e8db796 ("udp: perform source validation for mcast early demux")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Thu, 14 Jan 2021 18:19:29 +0000 (10:19 -0800)]
net_sched: gen_estimator: support large ewma log
commit
dd5e073381f2ada3630f36be42833c6e9c78b75e upstream.
syzbot report reminded us that very big ewma_log were supported in the past,
even if they made litle sense.
tc qdisc replace dev xxx root est 1sec 131072sec ...
While fixing the bug, also add boundary checks for ewma_log, in line
with range supported by iproute2.
UBSAN: shift-out-of-bounds in net/core/gen_estimator.c:83:38
shift exponent -1 is negative
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.10.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x107/0x163 lib/dump_stack.c:120
ubsan_epilogue+0xb/0x5a lib/ubsan.c:148
__ubsan_handle_shift_out_of_bounds.cold+0xb1/0x181 lib/ubsan.c:395
est_timer.cold+0xbb/0x12d net/core/gen_estimator.c:83
call_timer_fn+0x1a5/0x710 kernel/time/timer.c:1417
expire_timers kernel/time/timer.c:1462 [inline]
__run_timers.part.0+0x692/0xa80 kernel/time/timer.c:1731
__run_timers kernel/time/timer.c:1712 [inline]
run_timer_softirq+0xb3/0x1d0 kernel/time/timer.c:1744
__do_softirq+0x2bc/0xa77 kernel/softirq.c:343
asm_call_irq_on_stack+0xf/0x20
</IRQ>
__run_on_irqstack arch/x86/include/asm/irq_stack.h:26 [inline]
run_on_irqstack_cond arch/x86/include/asm/irq_stack.h:77 [inline]
do_softirq_own_stack+0xaa/0xd0 arch/x86/kernel/irq_64.c:77
invoke_softirq kernel/softirq.c:226 [inline]
__irq_exit_rcu+0x17f/0x200 kernel/softirq.c:420
irq_exit_rcu+0x5/0x20 kernel/softirq.c:432
sysvec_apic_timer_interrupt+0x4d/0x100 arch/x86/kernel/apic/apic.c:1096
asm_sysvec_apic_timer_interrupt+0x12/0x20 arch/x86/include/asm/idtentry.h:628
RIP: 0010:native_save_fl arch/x86/include/asm/irqflags.h:29 [inline]
RIP: 0010:arch_local_save_flags arch/x86/include/asm/irqflags.h:79 [inline]
RIP: 0010:arch_irqs_disabled arch/x86/include/asm/irqflags.h:169 [inline]
RIP: 0010:acpi_safe_halt drivers/acpi/processor_idle.c:111 [inline]
RIP: 0010:acpi_idle_do_entry+0x1c9/0x250 drivers/acpi/processor_idle.c:516
Fixes:
1c0d32fde5bd ("net_sched: gen_estimator: complete rewrite of rate estimators")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Link: https://lore.kernel.org/r/20210114181929.1717985-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yuchung Cheng [Tue, 19 Jan 2021 19:26:19 +0000 (11:26 -0800)]
tcp: fix TCP socket rehash stats mis-accounting
commit
9c30ae8398b0813e237bde387d67a7f74ab2db2d upstream.
The previous commit
32efcc06d2a1 ("tcp: export count for rehash attempts")
would mis-account rehashing SNMP and socket stats:
a. During handshake of an active open, only counts the first
SYN timeout
b. After handshake of passive and active open, stop updating
after (roughly) TCP_RETRIES1 recurring RTOs
c. After the socket aborts, over count timeout_rehash by 1
This patch fixes this by checking the rehash result from sk_rethink_txhash.
Fixes:
32efcc06d2a1 ("tcp: export count for rehash attempts")
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Link: https://lore.kernel.org/r/20210119192619.1848270-1-ycheng@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lecopzer Chen [Sun, 24 Jan 2021 05:01:29 +0000 (21:01 -0800)]
kasan: fix incorrect arguments passing in kasan_add_zero_shadow
commit
5dabd1712cd056814f9ab15f1d68157ceb04e741 upstream.
kasan_remove_zero_shadow() shall use original virtual address, start and
size, instead of shadow address.
Link: https://lkml.kernel.org/r/20210103063847.5963-1-lecopzer@gmail.com
Fixes:
0207df4fa1a86 ("kernel/memremap, kasan: make ZONE_DEVICE with work with KASAN")
Signed-off-by: Lecopzer Chen <lecopzer.chen@mediatek.com>
Reviewed-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Alexander Potapenko <glider@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lecopzer Chen [Sun, 24 Jan 2021 05:01:25 +0000 (21:01 -0800)]
kasan: fix unaligned address is unhandled in kasan_remove_zero_shadow
commit
a11a496ee6e2ab6ed850233c96b94caf042af0b9 upstream.
During testing kasan_populate_early_shadow and kasan_remove_zero_shadow,
if the shadow start and end address in kasan_remove_zero_shadow() is not
aligned to PMD_SIZE, the remain unaligned PTE won't be removed.
In the test case for kasan_remove_zero_shadow():
shadow_start: 0xffffffb802000000, shadow end: 0xffffffbfbe000000
3-level page table:
PUD_SIZE: 0x40000000 PMD_SIZE: 0x200000 PAGE_SIZE: 4K
0xffffffbf80000000 ~ 0xffffffbfbdf80000 will not be removed because in
kasan_remove_pud_table(), kasan_pmd_table(*pud) is true but the next
address is 0xffffffbfbdf80000 which is not aligned to PUD_SIZE.
In the correct condition, this should fallback to the next level
kasan_remove_pmd_table() but the condition flow always continue to skip
the unaligned part.
Fix by correcting the condition when next and addr are neither aligned.
Link: https://lkml.kernel.org/r/20210103135621.83129-1-lecopzer@gmail.com
Fixes:
0207df4fa1a86 ("kernel/memremap, kasan: make ZONE_DEVICE with work with KASAN")
Signed-off-by: Lecopzer Chen <lecopzer.chen@mediatek.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: YJ Chiang <yj.chiang@mediatek.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexander Lobakin [Fri, 15 Jan 2021 15:04:40 +0000 (15:04 +0000)]
skbuff: back tiny skbs with kmalloc() in __netdev_alloc_skb() too
commit
66c556025d687dbdd0f748c5e1df89c977b6c02a upstream.
Commit
3226b158e67c ("net: avoid 32 x truesize under-estimation for
tiny skbs") ensured that skbs with data size lower than 1025 bytes
will be kmalloc'ed to avoid excessive page cache fragmentation and
memory consumption.
However, the fix adressed only __napi_alloc_skb() (primarily for
virtio_net and napi_get_frags()), but the issue can still be achieved
through __netdev_alloc_skb(), which is still used by several drivers.
Drivers often allocate a tiny skb for headers and place the rest of
the frame to frags (so-called copybreak).
Mirror the condition to __netdev_alloc_skb() to handle this case too.
Since v1 [0]:
- fix "Fixes:" tag;
- refine commit message (mention copybreak usecase).
[0] https://lore.kernel.org/netdev/
20210114235423.232737-1-alobakin@pm.me
Fixes:
a1c7fff7e18f ("net: netdev_alloc_skb() use build_skb()")
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Link: https://lore.kernel.org/r/20210115150354.85967-1-alobakin@pm.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pan Bian [Thu, 21 Jan 2021 07:22:02 +0000 (23:22 -0800)]
lightnvm: fix memory leak when submit fails
commit
97784481757fba7570121a70dd37ca74a29f50a8 upstream.
The allocated page is not released if error occurs in
nvm_submit_io_sync_raw(). __free_page() is moved ealier to avoid
possible memory leak issue.
Fixes:
aff3fb18f957 ("lightnvm: move bad block and chunk state logic to core")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Wed, 20 Jan 2021 16:11:12 +0000 (16:11 +0000)]
cachefiles: Drop superfluous readpages aops NULL check
commit
db58465f1121086b524be80be39d1fedbe5387f3 upstream.
After the recent actions to convert readpages aops to readahead, the
NULL checks of readpages aops in cachefiles_read_or_alloc_page() may
hit falsely. More badly, it's an ASSERT() call, and this panics.
Drop the superfluous NULL checks for fixing this regression.
[DH: Note that cachefiles never actually used readpages, so this check was
never actually necessary]
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=208883
BugLink: https://bugzilla.opensuse.org/show_bug.cgi?id=1175245
Fixes:
9ae326a69004 ("CacheFiles: A cache that backs onto a mounted filesystem")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christoph Hellwig [Wed, 20 Jan 2021 08:35:01 +0000 (09:35 +0100)]
nvme-pci: fix error unwind in nvme_map_data
commit
fa0732168fa1369dd089e5b06d6158a68229f7b7 upstream.
Properly unwind step by step using refactored helpers from nvme_unmap_data
to avoid a potential double dma_unmap on a mapping failure.
Fixes:
7fe07d14f71f ("nvme-pci: merge nvme_free_iod into nvme_unmap_data")
Reported-by: Marc Orr <marcorr@google.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Marc Orr <marcorr@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christoph Hellwig [Wed, 20 Jan 2021 08:33:52 +0000 (09:33 +0100)]
nvme-pci: refactor nvme_unmap_data
commit
9275c206f88e5c49cb3e71932c81c8561083db9e upstream.
Split out three helpers from nvme_unmap_data that will allow finer grained
unwinding from nvme_map_data.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Marc Orr <marcorr@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Geert Uytterhoeven [Mon, 18 Jan 2021 15:08:12 +0000 (16:08 +0100)]
sh_eth: Fix power down vs. is_opened flag ordering
commit
f6a2e94b3f9d89cb40771ff746b16b5687650cbb upstream.
sh_eth_close() does a synchronous power down of the device before
marking it closed. Revert the order, to make sure the device is never
marked opened while suspended.
While at it, use pm_runtime_put() instead of pm_runtime_put_sync(), as
there is no reason to do a synchronous power down.
Fixes:
7fa2955ff70ce453 ("sh_eth: Fix sleeping function called from invalid context")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210118150812.796791-1-geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sandipan Das [Mon, 18 Jan 2021 09:31:45 +0000 (15:01 +0530)]
selftests/powerpc: Fix exit status of pkey tests
commit
92a5e1fdb286851d5bd0eb966b8d075be27cf5ee upstream.
Since main() does not return a value explicitly, the
return values from FAIL_IF() conditions are ignored
and the tests can still pass irrespective of failures.
This makes sure that we always explicitly return the
correct test exit status.
Fixes:
1addb6444791 ("selftests/powerpc: Add test for execute-disabled pkeys")
Fixes:
c27f2fd1705a ("selftests/powerpc: Add test for pkey siginfo verification")
Reported-by: Eirik Fuller <efuller@redhat.com>
Signed-off-by: Sandipan Das <sandipan@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210118093145.10134-1-sandipan@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rasmus Villemoes [Sat, 16 Jan 2021 02:39:35 +0000 (03:39 +0100)]
net: dsa: mv88e6xxx: also read STU state in mv88e6250_g1_vtu_getnext
commit
87fe04367d842c4d97a77303242d4dd4ac351e46 upstream.
mv88e6xxx_port_vlan_join checks whether the VTU already contains an
entry for the given vid (via mv88e6xxx_vtu_getnext), and if so, merely
changes the relevant .member[] element and loads the updated entry
into the VTU.
However, at least for the mv88e6250, the on-stack struct
mv88e6xxx_vtu_entry vlan never has its .state[] array explicitly
initialized, neither in mv88e6xxx_port_vlan_join() nor inside the
getnext implementation. So the new entry has random garbage for the
STU bits, breaking VLAN filtering.
When the VTU entry is initially created, those bits are all zero, and
we should make sure to keep them that way when the entry is updated.
Fixes:
92307069a96c (net: dsa: mv88e6xxx: Avoid VTU corruption on 6097)
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Tobias Waldekranz <tobias@waldekranz.com>
Tested-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yingjie Wang [Fri, 15 Jan 2021 14:10:04 +0000 (06:10 -0800)]
octeontx2-af: Fix missing check bugs in rvu_cgx.c
commit
b7ba6cfabc42fc846eb96e33f1edcd3ea6290a27 upstream.
In rvu_mbox_handler_cgx_mac_addr_get()
and rvu_mbox_handler_cgx_mac_addr_set(),
the msg is expected only from PFs that are mapped to CGX LMACs.
It should be checked before mapping,
so we add the is_cgx_config_permitted() in the functions.
Fixes:
96be2e0da85e ("octeontx2-af: Support for MAC address filters in CGX")
Signed-off-by: Yingjie Wang <wangyingjie55@126.com>
Reviewed-by: Geetha sowjanya<gakula@marvell.com>
Link: https://lore.kernel.org/r/1610719804-35230-1-git-send-email-wangyingjie55@126.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kai Vehmanen [Wed, 13 Jan 2021 15:07:15 +0000 (17:07 +0200)]
ASoC: SOF: Intel: fix page fault at probe if i915 init fails
commit
9c25af250214e45f6d1c21ff6239a1ffeeedf20e upstream.
The earlier commit to fix runtime PM in case i915 init fails,
introduces a possibility to hit a page fault.
snd_hdac_ext_bus_device_exit() is designed to be called from
dev.release(). Calling it outside device reference counting, is
not safe and may lead to calling the device_exit() function
twice. Additionally, as part of ext_bus_device_init(), the device
is also registered with snd_hdac_device_register(). Thus before
calling device_exit(), the device must be removed from device
hierarchy first.
Fix the issue by rolling back init actions by calling
hdac_device_unregister() and then releasing device with put_device().
This matches with existing code in hdac-ext module.
To complete the fix, add handling for the case where
hda_codec_load_module() returns -ENODEV, and clean up the hdac_ext
resources also in this case.
In future work, hdac-ext interface should be extended to allow clients
more flexibility to handle the life-cycle of individual devices, beyond
just the current snd_hdac_ext_bus_device_remove(), which removes all
devices.
BugLink: https://github.com/thesofproject/linux/issues/2646
Reported-by: Jaroslav Kysela <perex@perex.cz>
Fixes:
6c63c954e1c5 ("ASoC: SOF: fix a runtime pm issue in SOF when HDMI codec doesn't work")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Link: https://lore.kernel.org/r/20210113150715.3992635-1-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Zijlstra [Wed, 6 Jan 2021 14:36:22 +0000 (15:36 +0100)]
locking/lockdep: Cure noinstr fail
commit
0afda3a888dccf12557b41ef42eee942327d122b upstream.
When the compiler doesn't feel like inlining, it causes a noinstr
fail:
vmlinux.o: warning: objtool: lock_is_held_type()+0xb: call to lockdep_enabled() leaves .noinstr.text section
Fixes:
4d004099a668 ("lockdep: Fix lockdep recursion")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210106144017.592595176@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jinyang He [Mon, 12 Oct 2020 03:50:24 +0000 (11:50 +0800)]
sh: Remove unused HAVE_COPY_THREAD_TLS macro
commit
19170492735be935747b0545b7eed8bb40cc1209 upstream.
Fixes:
e1cc9d8d596e ("sh: switch to copy_thread_tls()")
Signed-off-by: Jinyang He <hejinyang@loongson.cn>
Signed-off-by: Rich Felker <dalias@libc.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Necip Fazil Yildiran [Thu, 17 Sep 2020 15:45:48 +0000 (18:45 +0300)]
sh: dma: fix kconfig dependency for G2_DMA
commit
f477a538c14d07f8c45e554c8c5208d588514e98 upstream.
When G2_DMA is enabled and SH_DMA is disabled, it results in the following
Kbuild warning:
WARNING: unmet direct dependencies detected for SH_DMA_API
Depends on [n]: SH_DMA [=n]
Selected by [y]:
- G2_DMA [=y] && SH_DREAMCAST [=y]
The reason is that G2_DMA selects SH_DMA_API without depending on or
selecting SH_DMA while SH_DMA_API depends on SH_DMA.
When G2_DMA was first introduced with commit
40f49e7ed77f
("sh: dma: Make G2 DMA configurable."), this wasn't an issue since
SH_DMA_API didn't have such dependency, and this way was the only way to
enable it since SH_DMA_API was non-visible. However, later SH_DMA_API was
made visible and dependent on SH_DMA with commit
d8902adcc1a9
("dmaengine: sh: Add Support SuperH DMA Engine driver").
Let G2_DMA depend on SH_DMA_API instead to avoid Kbuild issues.
Fixes:
d8902adcc1a9 ("dmaengine: sh: Add Support SuperH DMA Engine driver")
Signed-off-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Signed-off-by: Rich Felker <dalias@libc.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Anshuman Gupta [Mon, 11 Jan 2021 08:11:02 +0000 (13:41 +0530)]
drm/i915/hdcp: Update CP property in update_pipe
commit
b3c95d0bdb0855b1f28370629e9eebec6bceac17 upstream.
When crtc state need_modeset is true it is not necessary
it is going to be a real modeset, it can turns to be a
fastset instead of modeset.
This turns content protection property to be DESIRED and hdcp
update_pipe left with property to be in DESIRED state but
actual hdcp->value was ENABLED.
This issue is caught with DP MST setup, where we have multiple
connector in same DP_MST topology. When disabling HDCP on one of
DP MST connector leads to set the crtc state need_modeset to true
for all other crtc driving the other DP-MST topology connectors.
This turns up other DP MST connectors CP property to be DESIRED
despite the actual hdcp->value is ENABLED.
Above scenario fails the DP MST HDCP IGT test, disabling HDCP on
one MST stream should not cause to disable HDCP on another MST
stream on same DP MST topology.
v2:
- Fixed connector->base.registration_state == DRM_CONNECTOR_REGISTERED
WARN_ON.
v3:
- Commit log improvement. [Uma]
- Added a comment before scheduling prop_work. [Uma]
Fixes:
33f9a623bfc6 ("drm/i915/hdcp: Update CP as per the kernel internal state")
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-2-anshuman.gupta@intel.com
(cherry picked from commit
d276e16702e2d634094f75f69df3b493f359fe31)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kent Gibson [Thu, 7 Jan 2021 04:00:20 +0000 (12:00 +0800)]
tools: gpio: fix %llu warning in gpio-watch.c
commit
1fc7c1ef37f86f207b4db40aba57084bb2f6a69a upstream.
Some platforms, such as mips64, don't map __u64 to long long unsigned
int so using %llu produces a warning:
gpio-watch.c: In function ‘main’:
gpio-watch.c:89:30: warning: format ‘%llu’ expects argument of type ‘long long unsigned int’, but argument 4 has type ‘__u64’ {aka ‘long unsigned int’} [-Wformat=]
89 | printf("line %u: %s at %llu\n",
| ~~~^
| |
| long long unsigned int
| %lu
90 | chg.info.offset, event, chg.timestamp_ns);
| ~~~~~~~~~~~~~~~~
| |
| __u64 {aka long unsigned int}
Replace the %llu with PRIu64 and cast the argument to uint64_t.
Fixes:
33f0c47b8fb4 ("tools: gpio: implement gpio-watch")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kent Gibson [Thu, 7 Jan 2021 04:00:19 +0000 (12:00 +0800)]
tools: gpio: fix %llu warning in gpio-event-mon.c
commit
2fe7c2f99440d52613e1cf845c96e8e463c28111 upstream.
Some platforms, such as mips64, don't map __u64 to long long unsigned
int so using %llu produces a warning:
gpio-event-mon.c:110:37: warning: format ‘%llu’ expects argument of type ‘long long unsigned int’, but argument 3 has type ‘__u64’ {aka ‘long unsigned int’} [-Wformat=]
110 | fprintf(stdout, "GPIO EVENT at %llu on line %d (%d|%d) ",
| ~~~^
| |
| long long unsigned int
| %lu
111 | event.timestamp_ns, event.offset, event.line_seqno,
| ~~~~~~~~~~~~~~~~~~
| |
| __u64 {aka long unsigned int}
Replace the %llu with PRIu64 and cast the argument to uint64_t.
Fixes:
03fd11b03362 ("tools/gpio/gpio-event-mon: fix warning")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guillaume Nault [Sat, 16 Jan 2021 10:44:26 +0000 (11:44 +0100)]
netfilter: rpfilter: mask ecn bits before fib lookup
commit
2e5a6266fbb11ae93c468dfecab169aca9c27b43 upstream.
RT_TOS() only masks one of the two ECN bits. Therefore rpfilter_mt()
treats Not-ECT or ECT(1) packets in a different way than those with
ECT(0) or CE.
Reproducer:
Create two netns, connected with a veth:
$ ip netns add ns0
$ ip netns add ns1
$ ip link add name veth01 netns ns0 type veth peer name veth10 netns ns1
$ ip -netns ns0 link set dev veth01 up
$ ip -netns ns1 link set dev veth10 up
$ ip -netns ns0 address add 192.0.2.10/32 dev veth01
$ ip -netns ns1 address add 192.0.2.11/32 dev veth10
Add a route to ns1 in ns0:
$ ip -netns ns0 route add 192.0.2.11/32 dev veth01
In ns1, only packets with TOS 4 can be routed to ns0:
$ ip -netns ns1 route add 192.0.2.10/32 tos 4 dev veth10
Ping from ns0 to ns1 works regardless of the ECN bits, as long as TOS
is 4:
$ ip netns exec ns0 ping -Q 4 192.0.2.11 # TOS 4, Not-ECT
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 5 192.0.2.11 # TOS 4, ECT(1)
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 6 192.0.2.11 # TOS 4, ECT(0)
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 7 192.0.2.11 # TOS 4, CE
... 0% packet loss ...
Now use iptable's rpfilter module in ns1:
$ ip netns exec ns1 iptables-legacy -t raw -A PREROUTING -m rpfilter --invert -j DROP
Not-ECT and ECT(1) packets still pass:
$ ip netns exec ns0 ping -Q 4 192.0.2.11 # TOS 4, Not-ECT
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 5 192.0.2.11 # TOS 4, ECT(1)
... 0% packet loss ...
But ECT(0) and ECN packets are dropped:
$ ip netns exec ns0 ping -Q 6 192.0.2.11 # TOS 4, ECT(0)
... 100% packet loss ...
$ ip netns exec ns0 ping -Q 7 192.0.2.11 # TOS 4, CE
... 100% packet loss ...
After this patch, rpfilter doesn't drop ECT(0) and CE packets anymore.
Fixes:
8f97339d3feb ("netfilter: add ipv4 reverse path filter match")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cong Wang [Fri, 15 Jan 2021 18:50:24 +0000 (10:50 -0800)]
cls_flower: call nla_ok() before nla_next()
commit
c96adff95619178e2118925578343ad54857c80c upstream.
fl_set_enc_opt() simply checks if there are still bytes left to parse,
but this is not sufficent as syzbot seems to be able to generate
malformatted netlink messages. nla_ok() is more strict so should be
used to validate the next nlattr here.
And nla_validate_nested_deprecated() has less strict check too, it is
probably too late to switch to the strict version, but we can just
call nla_ok() too after it.
Reported-and-tested-by: syzbot+2624e3778b18fc497c92@syzkaller.appspotmail.com
Fixes:
0a6e77784f49 ("net/sched: allow flower to match tunnel options")
Fixes:
79b1011cb33d ("net: sched: allow flower to match erspan options")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Xin Long <lucien.xin@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Link: https://lore.kernel.org/r/20210115185024.72298-1-xiyou.wangcong@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yazen Ghannam [Mon, 11 Jan 2021 10:04:29 +0000 (11:04 +0100)]
x86/cpu/amd: Set __max_die_per_package on AMD
commit
76e2fc63ca40977af893b724b00cc2f8e9ce47a4 upstream.
Set the maximum DIE per package variable on AMD using the
NodesPerProcessor topology value. This will be used by RAPL, among
others, to determine the maximum number of DIEs on the system in order
to do per-DIE manipulations.
[ bp: Productize into a proper patch. ]
Fixes:
028c221ed190 ("x86/CPU/AMD: Save AMD NodeId as cpu_die_id")
Reported-by: Johnathan Smithinovic <johnathan.smithinovic@gmx.at>
Reported-by: Rafael Kitover <rkitover@gmail.com>
Signed-off-by: Yazen Ghannam <Yazen.Ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Johnathan Smithinovic <johnathan.smithinovic@gmx.at>
Tested-by: Rafael Kitover <rkitover@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=210939
Link: https://lkml.kernel.org/r/20210106112106.GE5729@zn.tnic
Link: https://lkml.kernel.org/r/20210111101455.1194-1-bp@alien8.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Zijlstra [Wed, 6 Jan 2021 14:36:20 +0000 (15:36 +0100)]
x86/entry: Fix noinstr fail
commit
9caa7ff509add50959a793b811cc7c9339e281cd upstream.
vmlinux.o: warning: objtool: __do_fast_syscall_32()+0x47: call to syscall_enter_from_user_mode_work() leaves .noinstr.text section
Fixes:
4facb95b7ada ("x86/entry: Unbreak 32bit fast syscall")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210106144017.472696632@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ville Syrjälä [Mon, 18 Jan 2021 15:43:55 +0000 (17:43 +0200)]
drm/i915: Only enable DFP 4:4:4->4:2:0 conversion when outputting YCbCr 4:4:4
commit
1c4995b0a576d24bb7ead991fb037c8b47ab6e32 upstream.
Let's not enable the 4:4:4->4:2:0 conversion bit in the DFP unless we're
actually outputting YCbCr 4:4:4. It would appear some protocol
converters blindy consult this bit even when the source is outputting
RGB, resulting in a visual mess.
Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2914
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111164111.13302-1-ville.syrjala@linux.intel.com
Fixes:
181567aa9f0d ("drm/i915: Do YCbCr 444->420 conversion via DP protocol converters")
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit
3170a21f7059c4660c469f59bf529f372a57da5f)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210118154355.24453-1-ville.syrjala@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ville Syrjälä [Fri, 16 Oct 2020 19:48:00 +0000 (22:48 +0300)]
drm/i915: s/intel_dp_sink_dpms/intel_dp_set_power/
commit
0e634efd858e0e9331ea037e1a142e34a446e9e3 upstream.
Rename intel_dp_sink_dpms() to intel_dp_set_power()
so one doesn't always have to convert from the DPMS
enum values to the actual DP D-states.
Also when dealing with a branch device this has nothing to
do with any sink, so the old name was nonsense anyway.
Also adjust the debug message accordingly, and pimp it
with the standard encoder id+name thing.
Trivial bits done with cocci:
@@
expression DP;
@@
(
- intel_dp_sink_dpms(DP, DRM_MODE_DPMS_OFF)
+ intel_dp_set_power(DP, DP_SET_POWER_D3)
|
- intel_dp_sink_dpms(DP, DRM_MODE_DPMS_ON)
+ intel_dp_set_power(DP, DP_SET_POWER_D0)
)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201016194800.25581-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rafael J. Wysocki [Fri, 15 Jan 2021 18:30:51 +0000 (19:30 +0100)]
driver core: Extend device_is_dependent()
commit
3d1cf435e201d1fd63e4346b141881aed086effd upstream.
If the device passed as the target (second argument) to
device_is_dependent() is not completely registered (that is, it has
been initialized, but not added yet), but the parent pointer of it
is set, it may be missing from the list of the parent's children
and device_for_each_child() called by device_is_dependent() cannot
be relied on to catch that dependency.
For this reason, modify device_is_dependent() to check the ancestors
of the target device by following its parent pointer in addition to
the device_for_each_child() walk.
Fixes:
9ed9895370ae ("driver core: Functional dependencies tracking support")
Reported-by: Stephan Gerhold <stephan@gerhold.net>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/17705994.d592GUb2YH@kreacher
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Saravana Kannan [Sun, 10 Jan 2021 17:54:07 +0000 (09:54 -0800)]
driver core: Fix device link device name collision
commit
e020ff611ba9be54e959e6b548038f8a020da1c9 upstream.
The device link device's name was of the form:
<supplier-dev-name>--<consumer-dev-name>
This can cause name collision as reported here [1] as device names are
not globally unique. Since device names have to be unique within the
bus/class, add the bus/class name as a prefix to the device names used to
construct the device link device name.
So the devuce link device's name will be of the form:
<supplier-bus-name>:<supplier-dev-name>--<consumer-bus-name>:<consumer-dev-name>
[1] - https://lore.kernel.org/lkml/
20201229033440.32142-1-michael@walle.cc/
Fixes:
287905e68dd2 ("driver core: Expose device link details in sysfs")
Cc: stable@vger.kernel.org
Reported-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20210110175408.1465657-1-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Meng Li [Tue, 5 Jan 2021 07:09:27 +0000 (15:09 +0800)]
drivers core: Free dma_range_map when driver probe failed
commit
d0243bbd5dd3ebbd49dafa8b56bb911d971131d0 upstream.
There will be memory leak if driver probe failed. Trace as below:
backtrace:
[<
000000002415258f>] kmemleak_alloc+0x3c/0x50
[<
00000000f447ebe4>] __kmalloc+0x208/0x530
[<
0000000048bc7b3a>] of_dma_get_range+0xe4/0x1b0
[<
0000000041e39065>] of_dma_configure_id+0x58/0x27c
[<
000000006356866a>] platform_dma_configure+0x2c/0x40
......
[<
000000000afcf9b5>] ret_from_fork+0x10/0x3c
This issue is introduced by commit
e0d072782c73("dma-mapping:
introduce DMA range map, supplanting dma_pfn_offset "). It doesn't
free dma_range_map when driver probe failed and cause above
memory leak. So, add code to free it in error path.
Fixes:
e0d072782c73 ("dma-mapping: introduce DMA range map, supplanting dma_pfn_offset ")
Cc: stable@vger.kernel.org
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Link: https://lore.kernel.org/r/20210105070927.14968-1-Meng.Li@windriver.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>