Wolfram Sang [Wed, 22 Sep 2021 09:10:06 +0000 (11:10 +0200)]
memory: renesas-rpc-if: Correct QSPI data transfer in Manual mode
commit
fff53a551db50f5edecaa0b29a64056ab8d2bbca upstream.
This patch fixes 2 problems:
[1] The output warning logs and data loss when performing
mount/umount then remount the device with jffs2 format.
[2] The access width of SMWDR[0:1]/SMRDR[0:1] register is wrong.
This is the sample warning logs when performing mount/umount then
remount the device with jffs2 format:
jffs2: jffs2_scan_inode_node(): CRC failed on node at 0x031c51d4:
Read 0x00034e00, calculated 0xadb272a7
The reason for issue [1] is that the writing data seems to
get messed up.
Data is only completed when the number of bytes is divisible by 4.
If you only have 3 bytes of data left to write, 1 garbage byte
is inserted after the end of the write stream.
If you only have 2 bytes of data left to write, 2 bytes of '00'
are added into the write stream.
If you only have 1 byte of data left to write, 2 bytes of '00'
are added into the write stream. 1 garbage byte is inserted after
the end of the write stream.
To solve problem [1], data must be written continuously in serial
and the write stream ends when data is out.
Following HW manual 62.2.15, access to SMWDR0 register should be
in the same size as the transfer size specified in the SPIDE[3:0]
bits in the manual mode enable setting register (SMENR).
Be sure to access from address 0.
So, in 16-bit transfer (SPIDE[3:0]=b'1100), SMWDR0 should be
accessed by 16-bit width.
Similar to SMWDR1, SMDDR0/1 registers.
In current code, SMWDR0 register is accessed by regmap_write()
that only set up to do 32-bit width.
To solve problem [2], data must be written 16-bit or 8-bit when
transferring 1-byte or 2-byte.
Fixes:
ca7d8b980b67 ("memory: add Renesas RPC-IF driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Duc Nguyen <duc.nguyen.ub@renesas.com>
[wsa: refactored to use regmap only via reg_read/reg_write]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922091007.5516-1-wsa+renesas@sang-engineering.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric W. Biederman [Wed, 1 Sep 2021 18:21:34 +0000 (13:21 -0500)]
signal: Remove the bogus sigkill_pending in ptrace_stop
commit
7d613f9f72ec8f90ddefcae038fdae5adb8404b3 upstream.
The existence of sigkill_pending is a little silly as it is
functionally a duplicate of fatal_signal_pending that is used in
exactly one place.
Checking for pending fatal signals and returning early in ptrace_stop
is actively harmful. It casues the ptrace_stop called by
ptrace_signal to return early before setting current->exit_code.
Later when ptrace_signal reads the signal number from
current->exit_code is undefined, making it unpredictable what will
happen.
Instead rely on the fact that schedule will not sleep if there is a
pending signal that can awaken a task.
Removing the explict sigkill_pending test fixes fixes ptrace_signal
when ptrace_stop does not stop because current->exit_code is always
set to to signr.
Cc: stable@vger.kernel.org
Fixes:
3d749b9e676b ("ptrace: simplify ptrace_stop()->sigkill_pending() path")
Fixes:
1a669c2f16d4 ("Add arch_ptrace_stop")
Link: https://lkml.kernel.org/r/87pmsyx29t.fsf@disp2133
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dmitry Osipenko [Sun, 24 Oct 2021 19:28:52 +0000 (22:28 +0300)]
ASoC: tegra: Restore AC97 support
commit
de8fc2b0a3f9930f3cbe801d40758bb1d80b0ad8 upstream.
The device-tree of AC97 codecs need to be parsed differently from I2S
codecs, plus codec device may need to be created. This was missed by the
patch that unified machine drivers into a single driver, fix it. It should
restore audio on Toradex Colibri board.
Cc: <stable@vger.kernel.org>
Fixes:
cc8f70f56039 ("ASoC: tegra: Unify ASoC machine drivers")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20211024192853.21957-1-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dmitry Osipenko [Sun, 24 Oct 2021 19:28:53 +0000 (22:28 +0300)]
ASoC: tegra: Set default card name for Trimslice
commit
824edd866a13db7dbb0d8e26d2142f10271b6460 upstream.
The default card name for Trimslice device should be "tegra-trimslice".
It got lost by accident during unification of machine sound drivers,
fix it.
Cc: <stable@vger.kernel.org>
Fixes:
cc8f70f56039 ("ASoC: tegra: Unify ASoC machine drivers")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20211024192853.21957-2-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alok Prasad [Wed, 27 Oct 2021 18:43:29 +0000 (18:43 +0000)]
RDMA/qedr: Fix NULL deref for query_qp on the GSI QP
commit
4f960393a0ee9a39469ceb7c8077ae8db665cc12 upstream.
This patch fixes a crash caused by querying the QP via netlink, and
corrects the state of GSI qp. GSI qp's have a NULL qed_qp.
The call trace is generated by:
$ rdma res show
BUG: kernel NULL pointer dereference, address:
0000000000000034
Hardware name: Dell Inc. PowerEdge R720/0M1GCR, BIOS 1.2.6 05/10/2012
RIP: 0010:qed_rdma_query_qp+0x33/0x1a0 [qed]
RSP: 0018:
ffffba560a08f580 EFLAGS:
00010206
RAX:
0000000200000000 RBX:
ffffba560a08f5b8 RCX:
0000000000000000
RDX:
ffffba560a08f5b8 RSI:
0000000000000000 RDI:
ffff9807ee458090
RBP:
ffffba560a08f5a0 R08:
0000000000000000 R09:
ffff9807890e7048
R10:
ffffba560a08f658 R11:
0000000000000000 R12:
0000000000000000
R13:
ffff9807ee458090 R14:
ffff9807f0afb000 R15:
ffffba560a08f7ec
FS:
00007fbbf8bfe740(0000) GS:
ffff980aafa00000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
0000000000000034 CR3:
00000001720ba001 CR4:
00000000000606f0
Call Trace:
qedr_query_qp+0x82/0x360 [qedr]
ib_query_qp+0x34/0x40 [ib_core]
? ib_query_qp+0x34/0x40 [ib_core]
fill_res_qp_entry_query.isra.26+0x47/0x1d0 [ib_core]
? __nla_put+0x20/0x30
? nla_put+0x33/0x40
fill_res_qp_entry+0xe3/0x120 [ib_core]
res_get_common_dumpit+0x3f8/0x5d0 [ib_core]
? fill_res_cm_id_entry+0x1f0/0x1f0 [ib_core]
nldev_res_get_qp_dumpit+0x1a/0x20 [ib_core]
netlink_dump+0x156/0x2f0
__netlink_dump_start+0x1ab/0x260
rdma_nl_rcv+0x1de/0x330 [ib_core]
? nldev_res_get_cm_id_dumpit+0x20/0x20 [ib_core]
netlink_unicast+0x1b8/0x270
netlink_sendmsg+0x33e/0x470
sock_sendmsg+0x63/0x70
__sys_sendto+0x13f/0x180
? setup_sgl.isra.12+0x70/0xc0
__x64_sys_sendto+0x28/0x30
do_syscall_64+0x3a/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
Cc: stable@vger.kernel.org
Fixes:
cecbcddf6461 ("qedr: Add support for QP verbs")
Link: https://lore.kernel.org/r/20211027184329.18454-1-palok@marvell.com
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kan Liang [Thu, 26 Aug 2021 15:32:39 +0000 (08:32 -0700)]
perf/x86/intel/uncore: Fix Intel ICX IIO event constraints
commit
f42e8a603c88f72bf047a710b9fc1d3579f31e71 upstream.
According to the latest uncore document, both NUM_OUTSTANDING_REQ_OF_CPU
(0x88) event and COMP_BUF_OCCUPANCY(0xd5) event also have constraints. Add
them into the event constraints table.
Fixes:
2b3b76b5ec67 ("perf/x86/intel/uncore: Add Ice Lake server uncore support")
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1629991963-102621-4-git-send-email-kan.liang@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kan Liang [Thu, 26 Aug 2021 15:32:38 +0000 (08:32 -0700)]
perf/x86/intel/uncore: Fix invalid unit check
commit
e2bb9fab08cbcc7922050c7eb0bd650807abfa4e upstream.
The uncore unit with the type ID 0 and the unit ID 0 is missed.
The table3 of the uncore unit maybe 0. The
uncore_discovery_invalid_unit() mistakenly treated it as an invalid
value.
Remove the !unit.table3 check.
Fixes:
edae1f06c2cd ("perf/x86/intel/uncore: Parse uncore discovery tables")
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1629991963-102621-3-git-send-email-kan.liang@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kan Liang [Thu, 26 Aug 2021 15:32:37 +0000 (08:32 -0700)]
perf/x86/intel/uncore: Support extra IMC channel on Ice Lake server
commit
496a18f09374ad89b3ab4366019bc3975db90234 upstream.
There are three channels on a Ice Lake server, but only two channels
will ever be active. Current perf only enables two channels.
Support the extra IMC channel, which may be activated on some Ice Lake
machines. For a non-activated channel, the SW can still access it. The
write will be ignored by the HW. 0 is always returned for the reading.
Fixes:
2b3b76b5ec67 ("perf/x86/intel/uncore: Add Ice Lake server uncore support")
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1629991963-102621-2-git-send-email-kan.liang@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marek Vasut [Thu, 16 Sep 2021 14:42:45 +0000 (16:42 +0200)]
rsi: Fix module dev_oper_mode parameter description
commit
31f97cf9f0c31143a2a6fcc89c4a1286ce20157e upstream.
The module parameters are missing dev_oper_mode 12, BT classic alone,
add it. Moreover, the parameters encode newlines, which ends up being
printed malformed e.g. by modinfo, so fix that too.
However, the module parameter string is duplicated in both USB and SDIO
modules and the dev_oper_mode mode enumeration in those module parameters
is a duplicate of macros used by the driver. Furthermore, the enumeration
is confusing.
So, deduplicate the module parameter string and use __stringify() to
encode the correct mode enumeration values into the module parameter
string. Finally, replace 'Wi-Fi' with 'Wi-Fi alone' and 'BT' with
'BT classic alone' to clarify what those modes really mean.
Fixes:
898b255339310 ("rsi: add module parameter operating mode")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Cc: Angus Ainslie <angus@akkea.ca>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Karun Eagalapati <karun256@gmail.com>
Cc: Martin Fuzzey <martin.fuzzey@flowbird.group>
Cc: Martin Kepplinger <martink@posteo.de>
Cc: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Cc: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: netdev@vger.kernel.org
Cc: <stable@vger.kernel.org> # 4.17+
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916144245.10181-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Martin Fuzzey [Mon, 30 Aug 2021 15:26:46 +0000 (17:26 +0200)]
rsi: fix rate mask set leading to P2P failure
commit
b515d097053a71d624e0c5840b42cd4caa653941 upstream.
P2P client mode was only working the first time.
On subsequent connection attempts the group was successfully created but
no data was sent (no transmitted data packets were seen with a sniffer).
The reason for this was that the hardware was being configured in fixed
rate mode with rate RSI_RATE_1 (1Mbps) which is not valid in the 5GHz band.
In P2P mode wpa_supplicant uses NL80211_CMD_SET_TX_BITRATE_MASK to disallow
the 11b rates in the 2.4GHz band which updated common->fixedrate_mask.
rsi_set_min_rate() then used the fixedrate_mask to calculate the minimum
allowed rate, or 0xffff = auto if none was found.
However that calculation did not account for the different rate sets
allowed in the different bands leading to the error.
Fixing set_min_rate() would result in 6Mb/s being used all the time
which is not what we want either.
The reason the problem did not occur on the first connection is that
rsi_mac80211_set_rate_mask() only updated the fixedrate_mask for
the *current* band. When it was called that was still 2.4GHz as the
switch is done later. So the when set_min_rate() was subsequently
called after the switch to 5GHz it still had a mask of zero, leading
to defaulting to auto mode.
Fix this by differentiating the case of a single rate being
requested, in which case the hardware will be used in fixed rate
mode with just that rate, and multiple rates being requested,
in which case we remain in auto mode but the firmware rate selection
algorithm is configured with a restricted set of rates.
Fixes:
dad0d04fa7ba ("rsi: Add RS9113 wireless driver")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
CC: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630337206-12410-4-git-send-email-martin.fuzzey@flowbird.group
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Martin Fuzzey [Mon, 30 Aug 2021 15:26:45 +0000 (17:26 +0200)]
rsi: fix key enabled check causing unwanted encryption for vap_id > 0
commit
99ac6018821253ec67f466086afb63fc18ea48e2 upstream.
My previous patch checked if encryption should be enabled by directly
checking info->control.hw_key (like the downstream driver).
However that missed that the control and driver_info members of
struct ieee80211_tx_info are union fields.
Due to this when rsi_core_xmit() updates fields in "tx_params"
(driver_info) it can overwrite the control.hw_key, causing the result
of the later test to be incorrect.
With the current structure layout the first byte of control.hw_key is
overlayed with the vap_id so, since we only test if control.hw_key is
NULL / non NULL, a non zero vap_id will incorrectly enable encryption.
In basic STA and AP modes the vap_id is always zero so it works but in
P2P client mode a second VIF is created causing vap_id to be non zero
and hence encryption to be enabled before keys have been set.
Fix this by extracting the key presence flag to a new field in the driver
private tx_params structure and populating it first.
Fixes:
314538041b56 ("rsi: fix AP mode with WPA failure due to encrypted EAPOL")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
CC: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630337206-12410-3-git-send-email-martin.fuzzey@flowbird.group
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Martin Fuzzey [Mon, 30 Aug 2021 15:26:44 +0000 (17:26 +0200)]
rsi: fix occasional initialisation failure with BT coex
commit
9b14ed6e11b72dd4806535449ca6c6962cb2369d upstream.
When BT coexistence is enabled (eg oper mode 13, which is the default)
the initialisation on startup sometimes silently fails.
In a normal initialisation we see
usb 1-1.3: Product: Wireless USB Network Module
usb 1-1.3: Manufacturer: Redpine Signals, Inc.
usb 1-1.3: SerialNumber:
000000000001
rsi_91x: rsi_probe: Initialized os intf ops
rsi_91x: rsi_load_9116_firmware: Loading chunk 0
rsi_91x: rsi_load_9116_firmware: Loading chunk 1
rsi_91x: rsi_load_9116_firmware: Loading chunk 2
rsi_91x: Max Stations Allowed = 1
But sometimes the last log is missing and the wlan net device is
not created.
Running a userspace loop that resets the hardware via a GPIO shows the
problem occurring ~5/100 resets.
The problem does not occur in oper mode 1 (wifi only).
Adding logs shows that the initialisation state machine requests a MAC
reset via rsi_send_reset_mac() but the firmware does not reply, leading
to the initialisation sequence being incomplete.
Fix this by delaying attaching the BT adapter until the wifi
initialisation has completed.
With this applied I have done > 300 reset loops with no errors.
Fixes:
716b840c7641 ("rsi: handle BT traffic in driver")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
CC: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630337206-12410-2-git-send-email-martin.fuzzey@flowbird.group
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Benjamin Li [Wed, 1 Sep 2021 18:06:05 +0000 (11:06 -0700)]
wcn36xx: handle connection loss indication
commit
d6dbce453b19c64b96f3e927b10230f9a704b504 upstream.
Firmware sends delete_sta_context_ind when it detects the AP has gone
away in STA mode. Right now the handler for that indication only handles
AP mode; fix it to also handle STA mode.
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Li <benl@squareup.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210901180606.11686-1-benl@squareup.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christian König [Tue, 15 Jun 2021 11:12:33 +0000 (13:12 +0200)]
dma-buf: fix and rework dma_buf_poll v7
commit
6b51b02a3a0ac49dfe302818d0746a799545e4e9 upstream.
Daniel pointed me towards this function and there are multiple obvious problems
in the implementation.
First of all the retry loop is not working as intended. In general the retry
makes only sense if you grab the reference first and then check the sequence
values.
Then we should always also wait for the exclusive fence.
It's also good practice to keep the reference around when installing callbacks
to fences you don't own.
And last the whole implementation was unnecessary complex and rather hard to
understand which could lead to probably unexpected behavior of the IOCTL.
Fix all this by reworking the implementation from scratch. Dropping the
whole RCU approach and taking the lock instead.
Only mildly tested and needs a thoughtful review of the code.
Pushing through drm-misc-next to avoid merge conflicts and give the code
another round of testing.
v2: fix the reference counting as well
v3: keep the excl fence handling as is for stable
v4: back to testing all fences, drop RCU
v5: handle in and out separately
v6: add missing clear of events
v7: change coding style as suggested by Michel, drop unused variables
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Michel Dänzer <mdaenzer@redhat.com>
CC: stable@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20210720131110.88512-1-christian.koenig@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reimar Döffinger [Tue, 12 Oct 2021 06:27:44 +0000 (08:27 +0200)]
libata: fix checking of DMA state
commit
f971a85439bd25dc7b4d597cf5e4e8dc7ffc884b upstream.
Checking if DMA is enabled should be done via the
ata_dma_enabled helper function, since the init state
0xff indicates disabled.
This meant that ATA_CMD_READ_LOG_DMA_EXT was used and probed
for before DMA was enabled, which caused hangs for some combinations
of controllers and devices.
It might also have caused it to be incorrectly disabled as broken,
but there have been no reports of that.
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=195895
Signed-off-by: Reimar Döffinger <Reimar.Doeffinger@gmx.de>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jonas Dreßler [Mon, 11 Oct 2021 13:32:24 +0000 (15:32 +0200)]
mwifiex: Try waking the firmware until we get an interrupt
commit
8e3e59c31fea5de95ffc52c46f0c562c39f20c59 upstream.
It seems that the PCIe+USB firmware (latest version 15.68.19.p21) of the
88W8897 card sometimes ignores or misses when we try to wake it up by
writing to the firmware status register. This leads to the firmware
wakeup timeout expiring and the driver resetting the card because we
assume the firmware has hung up or crashed.
Turns out that the firmware actually didn't hang up, but simply "missed"
our wakeup request and didn't send us an interrupt with an AWAKE event.
Trying again to read the firmware status register after a short timeout
usually makes the firmware wake up as expected, so add a small retry
loop to mwifiex_pm_wakeup_card() that looks at the interrupt status to
check whether the card woke up.
The number of tries and timeout lengths for this were determined
experimentally: The firmware usually takes about 500 us to wake up
after we attempt to read the status register. In some cases where the
firmware is very busy (for example while doing a bluetooth scan) it
might even miss our requests for multiple milliseconds, which is why
after 15 tries the waiting time gets increased to 10 ms. The maximum
number of tries it took to wake the firmware when testing this was
around 20, so a maximum number of 50 tries should give us plenty of
safety margin.
Here's a reproducer for those firmware wakeup failures I've found:
1) Make sure wifi powersaving is enabled (iw dev wlp1s0 set power_save on)
2) Connect to any wifi network (makes firmware go into wifi powersaving
mode, not deep sleep)
3) Make sure bluetooth is turned off (to ensure the firmware actually
enters powersave mode and doesn't keep the radio active doing bluetooth
stuff)
4) To confirm that wifi powersaving is entered ping a device on the LAN,
pings should be a few ms higher than without powersaving
5) Run "while true; do iwconfig; sleep 0.0001; done", this wakes and
suspends the firmware extremely often
6) Wait until things explode, for me it consistently takes <5 minutes
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109681
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011133224.15561-3-verdre@v0yd.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jonas Dreßler [Mon, 11 Oct 2021 13:32:23 +0000 (15:32 +0200)]
mwifiex: Read a PCI register after writing the TX ring write pointer
commit
e5f4eb8223aa740237cd463246a7debcddf4eda1 upstream.
On the 88W8897 PCIe+USB card the firmware randomly crashes after setting
the TX ring write pointer. The issue is present in the latest firmware
version 15.68.19.p21 of the PCIe+USB card.
Those firmware crashes can be worked around by reading any PCI register
of the card after setting that register, so read the PCI_VENDOR_ID
register here. The reason this works is probably because we keep the bus
from entering an ASPM state for a bit longer, because that's what causes
the cards firmware to crash.
This fixes a bug where during RX/TX traffic and with ASPM L1 substates
enabled (the specific substates where the issue happens appear to be
platform dependent), the firmware crashes and eventually a command
timeout appears in the logs.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109681
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011133224.15561-2-verdre@v0yd.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rafael J. Wysocki [Fri, 22 Oct 2021 12:58:23 +0000 (14:58 +0200)]
PM: sleep: Do not let "syscore" devices runtime-suspend during system transitions
commit
928265e3601cde78c7e0a3e518a93b27defed3b1 upstream.
There is no reason to allow "syscore" devices to runtime-suspend
during system-wide PM transitions, because they are subject to the
same possible failure modes as any other devices in that respect.
Accordingly, change device_prepare() and device_complete() to call
pm_runtime_get_noresume() and pm_runtime_put(), respectively, for
"syscore" devices too.
Fixes:
057d51a1268f ("Merge branch 'pm-sleep'")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Loic Poulain [Mon, 25 Oct 2021 13:12:18 +0000 (16:12 +0300)]
wcn36xx: Fix (QoS) null data frame bitrate/modulation
commit
d3fd2c95c1c13ec217d43ebef3c61cfa00a6cd37 upstream.
We observe unexpected connection drops with some APs due to
non-acked mac80211 generated null data frames (keep-alive).
After debugging and capture, we noticed that null frames are
submitted at standard data bitrate and that the given APs are
in trouble with that.
After setting the null frame bitrate to control bitrate, all
null frames are acked as expected and connection is maintained.
Not sure if it's a requirement of the specification, but it seems
the right thing to do anyway, null frames are mostly used for control
purpose (power-saving, keep-alive...), and submitting them with
a slower/simpler bitrate/modulation is more robust.
Cc: stable@vger.kernel.org
Fixes:
512b191d9652 ("wcn36xx: Fix TX data path")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634560399-15290-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Loic Poulain [Mon, 25 Oct 2021 13:12:18 +0000 (16:12 +0300)]
wcn36xx: Fix tx_status mechanism
commit
a9e79b116cc4d0057e912be8f40b2c2e5bdc7c43 upstream.
This change fix the TX ack mechanism in various ways:
- For NO_ACK tagged packets, we don't need to wait for TX_ACK indication
and so are not subject to the single packet ack limitation. So we don't
have to stop the tx queue, and can call the tx status callback as soon
as DMA transfer has completed.
- Fix skb ownership/reference. Only start status indication timeout
once the DMA transfer has been completed. This avoids the skb to be
both referenced in the DMA tx ring and by the tx_ack_skb pointer,
preventing any use-after-free or double-free.
- This adds a sanity (paranoia?) check on the skb tx ack pointer.
- Resume TX queue if TX status tagged packet TX fails.
Cc: stable@vger.kernel.org
Fixes:
fdf21cc37149 ("wcn36xx: Add TX ack support")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634567281-28997-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Loic Poulain [Wed, 20 Oct 2021 13:38:53 +0000 (15:38 +0200)]
wcn36xx: Fix HT40 capability for 2Ghz band
commit
960ae77f25631bbe4e3aafefe209b52e044baf31 upstream.
All wcn36xx controllers are supposed to support HT40 (and SGI40),
This doubles the maximum bitrate/throughput with compatible APs.
Tested with wcn3620 & wcn3680B.
Cc: stable@vger.kernel.org
Fixes:
8e84c2582169 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634737133-22336-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maximilian Luz [Thu, 21 Oct 2021 13:09:04 +0000 (15:09 +0200)]
HID: surface-hid: Allow driver matching for target ID 1 devices
commit
ab5fe33925c6b03f646a1153771dab047548e4d8 upstream.
Until now we have only ever seen HID devices with target ID 2. The new
Surface Laptop Studio however uses HID devices with target ID 1. Allow
matching this driver to those as well.
Cc: stable@vger.kernel.org # 5.14+
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20211021130904.862610-4-luzmaximilian@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maximilian Luz [Thu, 21 Oct 2021 13:09:03 +0000 (15:09 +0200)]
HID: surface-hid: Use correct event registry for managing HID events
commit
dc0fd0acb6e0e8025a0a43ada54513b216254fac upstream.
Until now, we have only ever seen the REG-category registry being used
on devices addressed with target ID 2. In fact, we have only ever seen
Surface Aggregator Module (SAM) HID devices with target ID 2. For those
devices, the registry also has to be addressed with target ID 2.
Some devices, like the new Surface Laptop Studio, however, address their
HID devices on target ID 1. As a result of this, any target ID 2
commands time out. This includes event management commands addressed to
the target ID 2 REG-category registry. For these devices, the registry
has to be addressed via target ID 1 instead.
We therefore assume that the target ID of the registry to be used
depends on the target ID of the respective device. Implement this
accordingly.
Note that we currently allow the surface HID driver to only load against
devices with target ID 2, so these timeouts are not happening (yet).
This is just a preparation step before we allow the driver to load
against all target IDs.
Cc: stable@vger.kernel.org # 5.14+
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20211021130904.862610-3-luzmaximilian@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Felix Fietkau [Wed, 21 Jul 2021 05:23:46 +0000 (07:23 +0200)]
mt76: mt7615: fix skb use-after-free on mac reset
commit
b5cd1fd6043bbb7c5810067b5f93f3016bfd8a6f upstream.
When clearing all existing pending tx slots, mt76_tx_complete_skb needs to
be used to free the skbs, to ensure that they are cleared from the status
list as well.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maximilian Luz [Thu, 21 Oct 2021 13:09:02 +0000 (15:09 +0200)]
platform/surface: aggregator_registry: Add support for Surface Laptop Studio
commit
4f042e40199ce8bac6bc2b853e81744ee4ea759c upstream.
Add support for the Surface Laptop Studio.
In contrast to previous Surface Laptop models, this one has its HID
devices attached to target ID 1 (instead of 2). It also has a couple
more of them, including a new notifier for when the pen is stashed /
taken out of its place, a "Sys Control" device, and two other
unidentified HID devices with unknown usages.
Battery and performance profile interfaces remain the same.
Cc: stable@vger.kernel.org # 5.14+
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20211021130904.862610-2-luzmaximilian@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lukas Wunner [Tue, 26 Oct 2021 05:15:32 +0000 (07:15 +0200)]
ifb: Depend on netfilter alternatively to tc
commit
046178e726c2977d686ba5e07105d5a6685c830e upstream.
IFB originally depended on NET_CLS_ACT for traffic redirection.
But since v4.5, that may be achieved with NFT_FWD_NETDEV as well.
Fixes:
39e6dea28adc ("netfilter: nf_tables: add forward expression to the netdev family")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v4.5+: bcfabee1afd9: netfilter: nft_fwd_netdev: allow to redirect to ifb via ingress
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Austin Kim [Thu, 28 Oct 2021 11:26:42 +0000 (12:26 +0100)]
evm: mark evm_fixmode as __ro_after_init
commit
32ba540f3c2a7ef61ed5a577ce25069a3d714fc9 upstream.
The evm_fixmode is only configurable by command-line option and it is never
modified outside initcalls, so declaring it with __ro_after_init is better.
Signed-off-by: Austin Kim <austin.kim@lge.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Mon, 25 Oct 2021 12:05:21 +0000 (14:05 +0200)]
rtl8187: fix control-message timeouts
commit
2e9be536a213e838daed6ba42024dd68954ac061 upstream.
USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.
Fixes:
605bebe23bf6 ("[PATCH] Add rtl8187 wireless driver")
Cc: stable@vger.kernel.org # 2.6.23
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211025120522.6045-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ingmar Klein [Fri, 9 Apr 2021 09:26:33 +0000 (11:26 +0200)]
PCI: Mark Atheros QCA6174 to avoid bus reset
commit
e3f4bd3462f6f796594ecc0dda7144ed2d1e5a26 upstream.
When passing the Atheros QCA6174 through to a virtual machine, the VM hangs
at the point where the ath10k driver loads.
Add a quirk to avoid bus resets on this device, which avoids the hang.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/08982e05-b6e8-5a8d-24ab-da1488ee50a8@web.de
Signed-off-by: Ingmar Klein <ingmar_klein@web.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Wed, 27 Oct 2021 08:08:17 +0000 (10:08 +0200)]
ath10k: fix division by zero in send path
commit
a006acb931317aad3a8dd41333ebb0453caf49b8 upstream.
Add the missing endpoint max-packet sanity check to probe() to avoid
division by zero in ath10k_usb_hif_tx_sg() in case a malicious device
has broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit
2548288b4fb0 ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes:
4db66499df91 ("ath10k: add initial USB support")
Cc: stable@vger.kernel.org # 4.14
Cc: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027080819.6675-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Mon, 25 Oct 2021 12:05:19 +0000 (14:05 +0200)]
ath10k: fix control-message timeout
commit
5286132324230168d3fab6ffc16bfd7de85bdfb4 upstream.
USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.
Fixes:
4db66499df91 ("ath10k: add initial USB support")
Cc: stable@vger.kernel.org # 4.14
Cc: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211025120522.6045-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Mon, 25 Oct 2021 12:05:20 +0000 (14:05 +0200)]
ath6kl: fix control-message timeout
commit
a066d28a7e729f808a3e6eff22e70c003091544e upstream.
USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.
Fixes:
241b128b6b69 ("ath6kl: add back beginnings of USB support")
Cc: stable@vger.kernel.org # 3.4
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211025120522.6045-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Wed, 27 Oct 2021 08:08:18 +0000 (10:08 +0200)]
ath6kl: fix division by zero in send path
commit
c1b9ca365deae667192be9fe24db244919971234 upstream.
Add the missing endpoint max-packet sanity check to probe() to avoid
division by zero in ath10k_usb_hif_tx_sg() in case a malicious device
has broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit
2548288b4fb0 ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes:
9cbee358687e ("ath6kl: add full USB support")
Cc: stable@vger.kernel.org # 3.5
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027080819.6675-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Wed, 27 Oct 2021 08:08:19 +0000 (10:08 +0200)]
mwifiex: fix division by zero in fw download path
commit
89f8765a11d8df49296d92c404067f9b5c58ee26 upstream.
Add the missing endpoint sanity checks to probe() to avoid division by
zero in mwifiex_write_data_sync() in case a malicious device has broken
descriptors (or when doing descriptor fuzz testing).
Only add checks for the firmware-download boot stage, which require both
command endpoints, for now. The driver looks like it will handle a
missing endpoint during normal operation without oopsing, albeit not
very gracefully as it will try to submit URBs to the default pipe and
fail.
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit
2548288b4fb0 ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes:
4daffe354366 ("mwifiex: add support for Marvell USB8797 chipset")
Cc: stable@vger.kernel.org # 3.5
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027080819.6675-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Badger [Sun, 10 Oct 2021 17:06:56 +0000 (10:06 -0700)]
EDAC/sb_edac: Fix top-of-high-memory value for Broadwell/Haswell
commit
537bddd069c743759addf422d0b8f028ff0f8dbc upstream.
The computation of TOHM is off by one bit. This missed bit results in
too low a value for TOHM, which can cause errors in regular memory to
incorrectly report:
EDAC MC0: 1 CE Error at MMIOH area, on addr 0x000000207fffa680 on any memory
Fixes:
50d1bb93672f ("sb_edac: add support for Haswell based systems")
Cc: stable@vger.kernel.org
Reported-by: Meeta Saggi <msaggi@purestorage.com>
Signed-off-by: Eric Badger <ebadger@purestorage.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20211010170127.848113-1-ebadger@purestorage.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Krzysztof Kozlowski [Fri, 8 Oct 2021 11:37:14 +0000 (13:37 +0200)]
regulator: dt-bindings: samsung,s5m8767: correct s5m8767,pmic-buck-default-dvs-idx property
commit
a7fda04bc9b6ad9da8e19c9e6e3b1dab773d068a upstream.
The driver was always parsing "s5m8767,pmic-buck-default-dvs-idx", not
"s5m8767,pmic-buck234-default-dvs-idx".
Cc: <stable@vger.kernel.org>
Fixes:
26aec009f6b6 ("regulator: add device tree support for s5m8767")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Rob Herring <robh@kernel.org>
Message-Id: <
20211008113723.134648-3-krzysztof.kozlowski@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Krzysztof Kozlowski [Fri, 8 Oct 2021 11:37:13 +0000 (13:37 +0200)]
regulator: s5m8767: do not use reset value as DVS voltage if GPIO DVS is disabled
commit
b16bef60a9112b1e6daf3afd16484eb06e7ce792 upstream.
The driver and its bindings, before commit
04f9f068a619 ("regulator:
s5m8767: Modify parsing method of the voltage table of buck2/3/4") were
requiring to provide at least one safe/default voltage for DVS registers
if DVS GPIO is not being enabled.
IOW, if s5m8767,pmic-buck2-uses-gpio-dvs is missing, the
s5m8767,pmic-buck2-dvs-voltage should still be present and contain one
voltage.
This requirement was coming from driver behavior matching this condition
(none of DVS GPIO is enabled): it was always initializing the DVS
selector pins to 0 and keeping the DVS enable setting at reset value
(enabled). Therefore if none of DVS GPIO is enabled in devicetree,
driver was configuring the first DVS voltage for buck[234].
Mentioned commit
04f9f068a619 ("regulator: s5m8767: Modify parsing
method of the voltage table of buck2/3/4") broke it because DVS voltage
won't be parsed from devicetree if DVS GPIO is not enabled. After the
change, driver will configure bucks to use the register reset value as
voltage which might have unpleasant effects.
Fix this by relaxing the bindings constrain: if DVS GPIO is not enabled
in devicetree (therefore DVS voltage is also not parsed), explicitly
disable it.
Cc: <stable@vger.kernel.org>
Fixes:
04f9f068a619 ("regulator: s5m8767: Modify parsing method of the voltage table of buck2/3/4")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Rob Herring <robh@kernel.org>
Message-Id: <
20211008113723.134648-2-krzysztof.kozlowski@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Zev Weiss [Tue, 28 Sep 2021 09:22:35 +0000 (02:22 -0700)]
hwmon: (pmbus/lm25066) Add offset coefficients
commit
ae59dc455a78fb73034dd1fbb337d7e59c27cbd8 upstream.
With the exception of the lm5066i, all the devices handled by this
driver had been missing their offset ('b') coefficients for direct
format readings.
Cc: stable@vger.kernel.org
Fixes:
58615a94f6a1 ("hwmon: (pmbus/lm25066) Add support for LM25056")
Fixes:
e53e6497fc9f ("hwmon: (pmbus/lm25066) Refactor device specific coefficients")
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20210928092242.30036-2-zev@bewilderbeest.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guoqing Jiang [Mon, 4 Oct 2021 15:34:48 +0000 (23:34 +0800)]
md/raid1: only allocate write behind bio for WriteMostly device
commit
fd3b6975e9c11c4fa00965f82a0bfbb3b7b44101 upstream.
Commit
6607cd319b6b91bff94e90f798a61c031650b514 ("raid1: ensure write
behind bio has less than BIO_MAX_VECS sectors") tried to guarantee the
size of behind bio is not bigger than BIO_MAX_VECS sectors.
Unfortunately the same calltrace still could happen since an array could
enable write-behind without write mostly device.
To match the manpage of mdadm (which says "write-behind is only attempted
on drives marked as write-mostly"), we need to check WriteMostly flag to
avoid such unexpected behavior.
[1]. https://bugzilla.kernel.org/show_bug.cgi?id=213181#c25
Cc: stable@vger.kernel.org # v5.12+
Cc: Jens Stutte <jens@chianterastutte.eu>
Reported-by: Jens Stutte <jens@chianterastutte.eu>
Signed-off-by: Guoqing Jiang <guoqing.jiang@linux.dev>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Corey Minyard [Mon, 20 Sep 2021 11:25:37 +0000 (06:25 -0500)]
ipmi:watchdog: Set panic count to proper value on a panic
commit
db05ddf7f321634c5659a0cf7ea56594e22365f7 upstream.
You will get two decrements when the messages on a panic are sent, not
one, since commit
2033f6858970 ("ipmi: Free receive messages when in an
oops") was added, but the watchdog code had a bug where it didn't set
the value properly.
Reported-by: Anton Lundin <glance@acc.umu.se>
Cc: <Stable@vger.kernel.org> # v5.4+
Fixes:
2033f6858970 ("ipmi: Free receive messages when in an oops")
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ondrej Mosnacek [Wed, 28 Jul 2021 14:03:13 +0000 (16:03 +0200)]
selinux: fix race condition when computing ocontext SIDs
commit
cbfcd13be5cb2a07868afe67520ed181956579a7 upstream.
Current code contains a lot of racy patterns when converting an
ocontext's context structure to an SID. This is being done in a "lazy"
fashion, such that the SID is looked up in the SID table only when it's
first needed and then cached in the "sid" field of the ocontext
structure. However, this is done without any locking or memory barriers
and is thus unsafe.
Between commits
24ed7fdae669 ("selinux: use separate table for initial
SID lookup") and
66f8e2f03c02 ("selinux: sidtab reverse lookup hash
table"), this race condition lead to an actual observable bug, because a
pointer to the shared sid field was passed directly to
sidtab_context_to_sid(), which was using this location to also store an
intermediate value, which could have been read by other threads and
interpreted as an SID. In practice this caused e.g. new mounts to get a
wrong (seemingly random) filesystem context, leading to strange denials.
This bug has been spotted in the wild at least twice, see [1] and [2].
Fix the race condition by making all the racy functions use a common
helper that ensures the ocontext::sid accesses are made safely using the
appropriate SMP constructs.
Note that security_netif_sid() was populating the sid field of both
contexts stored in the ocontext, but only the first one was actually
used. The SELinux wiki's documentation on the "netifcon" policy
statement [3] suggests that using only the first context is intentional.
I kept only the handling of the first context here, as there is really
no point in doing the SID lookup for the unused one.
I wasn't able to reproduce the bug mentioned above on any kernel that
includes commit
66f8e2f03c02, even though it has been reported that the
issue occurs with that commit, too, just less frequently. Thus, I wasn't
able to verify that this patch fixes the issue, but it makes sense to
avoid the race condition regardless.
[1] https://github.com/containers/container-selinux/issues/89
[2] https://lists.fedoraproject.org/archives/list/selinux@lists.fedoraproject.org/thread/6DMTAMHIOAOEMUAVTULJD45JZU7IBAFM/
[3] https://selinuxproject.org/page/NetworkStatements#netifcon
Cc: stable@vger.kernel.org
Cc: Xinjie Zheng <xinjie@google.com>
Reported-by: Sujithra Periasamy <sujithra@google.com>
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Masami Hiramatsu [Tue, 14 Sep 2021 14:40:27 +0000 (23:40 +0900)]
ia64: kprobes: Fix to pass correct trampoline address to the handler
commit
a7fe2378454cf46cd5e2776d05e72bbe8f0a468c upstream.
The following commit:
Commit
e792ff804f49 ("ia64: kprobes: Use generic kretprobe trampoline handler")
Passed the wrong trampoline address to __kretprobe_trampoline_handler(): it
passes the descriptor address instead of function entry address.
Pass the right parameter.
Also use correct symbol dereference function to get the function address
from 'kretprobe_trampoline' - an IA64 special.
Link: https://lkml.kernel.org/r/163163042696.489837.12551102356265354730.stgit@devnote2
Fixes:
e792ff804f49 ("ia64: kprobes: Use generic kretprobe trampoline handler")
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: X86 ML <x86@kernel.org>
Cc: Daniel Xu <dxu@dxuuu.xyz>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Abhishek Sagar <sagar.abhishek@gmail.com>
Cc: Andrii Nakryiko <andrii.nakryiko@gmail.com>
Cc: Paul McKenney <paulmck@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Laurent Vivier [Wed, 27 Oct 2021 14:21:50 +0000 (00:21 +1000)]
KVM: PPC: Tick accounting should defer vtime accounting 'til after IRQ handling
commit
235cee162459d96153d63651ce7ff51752528c96 upstream.
Commit
112665286d08 ("KVM: PPC: Book3S HV: Context tracking exit guest
context before enabling irqs") moved guest_exit() into the interrupt
protected area to avoid wrong context warning (or worse). The problem is
that tick-based time accounting has not yet been updated at this point
(because it depends on the timer interrupt firing), so the guest time
gets incorrectly accounted to system time.
To fix the problem, follow the x86 fix in commit
160457140187 ("Defer
vtime accounting 'til after IRQ handling"), and allow host IRQs to run
before accounting the guest exit time.
In the case vtime accounting is enabled, this is not required because TB
is used directly for accounting.
Before this patch, with CONFIG_TICK_CPU_ACCOUNTING=y in the host and a
guest running a kernel compile, the 'guest' fields of /proc/stat are
stuck at zero. With the patch they can be observed increasing roughly as
expected.
Fixes:
e233d54d4d97 ("KVM: booke: use __kvm_guest_exit")
Fixes:
112665286d08 ("KVM: PPC: Book3S HV: Context tracking exit guest context before enabling irqs")
Cc: stable@vger.kernel.org # 5.12+
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
[np: only required for tick accounting, add Book3E fix, tweak changelog]
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211027142150.3711582-1-npiggin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sean Christopherson [Sat, 9 Oct 2021 00:11:05 +0000 (17:11 -0700)]
KVM: VMX: Unregister posted interrupt wakeup handler on hardware unsetup
commit
ec5a4919fa7b7d8c7a2af1c7e799b1fe4be84343 upstream.
Unregister KVM's posted interrupt wakeup handler during unsetup so that a
spurious interrupt that arrives after kvm_intel.ko is unloaded doesn't
call into freed memory.
Fixes:
bf9f6ac8d749 ("KVM: Update Posted-Interrupts Descriptor when vCPU is blocked")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <
20211009001107.3936588-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sean Christopherson [Fri, 22 Oct 2021 01:00:03 +0000 (18:00 -0700)]
KVM: x86/mmu: Drop a redundant, broken remote TLB flush
commit
bc3b3c1002ea684e618ff6d8c387b1b8b319f140 upstream.
A recent commit to fix the calls to kvm_flush_remote_tlbs_with_address()
in kvm_zap_gfn_range() inadvertantly added yet another flush instead of
fixing the existing flush. Drop the redundant flush, and fix the params
for the existing flush.
Cc: stable@vger.kernel.org
Fixes:
2822da446640 ("KVM: x86/mmu: fix parameters to kvm_flush_remote_tlbs_with_address")
Cc: Maxim Levitsky <mlevitsk@redhat.com>
Cc: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <
20211022010005.1454978-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Anand Jain [Tue, 19 Oct 2021 10:43:38 +0000 (18:43 +0800)]
btrfs: call btrfs_check_rw_degradable only if there is a missing device
commit
5c78a5e7aa835c4f08a7c90fe02d19f95a776f29 upstream.
In open_ctree() in btrfs_check_rw_degradable() [1], we check each block
group individually if at least the minimum number of devices is available
for that profile. If all the devices are available, then we don't have to
check degradable.
[1]
open_ctree()
::
3559 if (!sb_rdonly(sb) && !btrfs_check_rw_degradable(fs_info, NULL)) {
Also before calling btrfs_check_rw_degradable() in open_ctee() at the
line number shown below [2] we call btrfs_read_chunk_tree() and down to
add_missing_dev() to record number of missing devices.
[2]
open_ctree()
::
3454 ret = btrfs_read_chunk_tree(fs_info);
btrfs_read_chunk_tree()
read_one_chunk() / read_one_dev()
add_missing_dev()
So, check if there is any missing device before btrfs_check_rw_degradable()
in open_ctree().
Also, with this the mount command could save ~16ms.[3] in the most
common case, that is no device is missing.
[3]
1) * 16934.96 us | btrfs_check_rw_degradable [btrfs]();
CC: stable@vger.kernel.org # 4.19+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Filipe Manana [Thu, 14 Oct 2021 16:26:04 +0000 (17:26 +0100)]
btrfs: fix lost error handling when replaying directory deletes
commit
10adb1152d957a4d570ad630f93a88bb961616c1 upstream.
At replay_dir_deletes(), if find_dir_range() returns an error we break out
of the main while loop and then assign a value of 0 (success) to the 'ret'
variable, resulting in completely ignoring that an error happened. Fix
that by jumping to the 'out' label when find_dir_range() returns an error
(negative value).
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Li Zhang [Mon, 4 Oct 2021 17:15:33 +0000 (01:15 +0800)]
btrfs: clear MISSING device status bit in btrfs_close_one_device
commit
5d03dbebba2594d2e6fbf3b5dd9060c5a835de3b upstream.
Reported bug: https://github.com/kdave/btrfs-progs/issues/389
There's a problem with scrub reporting aborted status but returning
error code 0, on a filesystem with missing and readded device.
Roughly these steps:
- mkfs -d raid1 dev1 dev2
- fill with data
- unmount
- make dev1 disappear
- mount -o degraded
- copy more data
- make dev1 appear again
Running scrub afterwards reports that the command was aborted, but the
system log message says the exit code was 0.
It seems that the cause of the error is decrementing
fs_devices->missing_devices but not clearing device->dev_state. Every
time we umount filesystem, it would call close_ctree, And it would
eventually involve btrfs_close_one_device to close the device, but it
only decrements fs_devices->missing_devices but does not clear the
device BTRFS_DEV_STATE_MISSING bit. Worse, this bug will cause Integer
Overflow, because every time umount, fs_devices->missing_devices will
decrease. If fs_devices->missing_devices value hit 0, it would overflow.
With added debugging:
loop1: detected capacity change from 0 to
20971520
BTRFS: device fsid
56ad51f1-5523-463b-8547-
c19486c51ebb devid 1 transid 21 /dev/loop1 scanned by systemd-udevd (2311)
loop2: detected capacity change from 0 to
20971520
BTRFS: device fsid
56ad51f1-5523-463b-8547-
c19486c51ebb devid 2 transid 17 /dev/loop2 scanned by systemd-udevd (2313)
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): using free space tree
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.
00000000f706684d /dev/loop1 0
BTRFS warning (device loop1): devid 2 uuid
6635ac31-56dd-4852-873b-
c60f5e2d53d2 is missing
BTRFS info (device loop1): before clear_missing.
0000000000000000 /dev/loop2 1
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): using free space tree
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.
00000000f706684d /dev/loop1 0
BTRFS warning (device loop1): devid 2 uuid
6635ac31-56dd-4852-873b-
c60f5e2d53d2 is missing
BTRFS info (device loop1): before clear_missing.
0000000000000000 /dev/loop2 0
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): using free space tree
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.
00000000f706684d /dev/loop1
18446744073709551615
BTRFS warning (device loop1): devid 2 uuid
6635ac31-56dd-4852-873b-
c60f5e2d53d2 is missing
BTRFS info (device loop1): before clear_missing.
0000000000000000 /dev/loop2
18446744073709551615
If fs_devices->missing_devices is 0, next time it would be
18446744073709551615
After apply this patch, the fs_devices->missing_devices seems to be
right:
$ truncate -s 10g test1
$ truncate -s 10g test2
$ losetup /dev/loop1 test1
$ losetup /dev/loop2 test2
$ mkfs.btrfs -draid1 -mraid1 /dev/loop1 /dev/loop2 -f
$ losetup -d /dev/loop2
$ mount -o degraded /dev/loop1 /mnt/1
$ umount /mnt/1
$ mount -o degraded /dev/loop1 /mnt/1
$ umount /mnt/1
$ mount -o degraded /dev/loop1 /mnt/1
$ umount /mnt/1
$ dmesg
loop1: detected capacity change from 0 to
20971520
loop2: detected capacity change from 0 to
20971520
BTRFS: device fsid
15aa1203-98d3-4a66-bcae-
ca82f629c2cd devid 1 transid 5 /dev/loop1 scanned by mkfs.btrfs (1863)
BTRFS: device fsid
15aa1203-98d3-4a66-bcae-
ca82f629c2cd devid 2 transid 5 /dev/loop2 scanned by mkfs.btrfs (1863)
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): disk space caching is enabled
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.
00000000975bd577 /dev/loop1 0
BTRFS warning (device loop1): devid 2 uuid
8b333791-0b3f-4f57-b449-
1c1ab6b51f38 is missing
BTRFS info (device loop1): before clear_missing.
0000000000000000 /dev/loop2 1
BTRFS info (device loop1): checking UUID tree
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): disk space caching is enabled
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.
00000000975bd577 /dev/loop1 0
BTRFS warning (device loop1): devid 2 uuid
8b333791-0b3f-4f57-b449-
1c1ab6b51f38 is missing
BTRFS info (device loop1): before clear_missing.
0000000000000000 /dev/loop2 1
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): disk space caching is enabled
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.
00000000975bd577 /dev/loop1 0
BTRFS warning (device loop1): devid 2 uuid
8b333791-0b3f-4f57-b449-
1c1ab6b51f38 is missing
BTRFS info (device loop1): before clear_missing.
0000000000000000 /dev/loop2 1
CC: stable@vger.kernel.org # 4.19+
Signed-off-by: Li Zhang <zhanglikernel@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Zijlstra [Fri, 17 Sep 2021 09:20:04 +0000 (11:20 +0200)]
x86/iopl: Fake iopl(3) CLI/STI usage
commit
b968e84b509da593c50dc3db679e1d33de701f78 upstream.
Since commit
c8137ace5638 ("x86/iopl: Restrict iopl() permission
scope") it's possible to emulate iopl(3) using ioperm(), except for
the CLI/STI usage.
Userspace CLI/STI usage is very dubious (read broken), since any
exception taken during that window can lead to rescheduling anyway (or
worse). The IOPL(2) manpage even states that usage of CLI/STI is highly
discouraged and might even crash the system.
Of course, that won't stop people and HP has the dubious honour of
being the first vendor to be found using this in their hp-health
package.
In order to enable this 'software' to still 'work', have the #GP treat
the CLI/STI instructions as NOPs when iopl(3). Warn the user that
their program is doing dubious things.
Fixes:
a24ca9976843 ("x86/iopl: Remove legacy IOPL option")
Reported-by: Ondrej Zary <linux@zary.sk>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org # v5.5+
Link: https://lkml.kernel.org/r/20210918090641.GD5106@worktop.programming.kicks-ass.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sean Christopherson [Sat, 9 Oct 2021 00:11:04 +0000 (17:11 -0700)]
x86/irq: Ensure PI wakeup handler is unregistered before module unload
commit
6ff53f6a438f72998f56e82e76694a1df9d1ea2c upstream.
Add a synchronize_rcu() after clearing the posted interrupt wakeup handler
to ensure all readers, i.e. in-flight IRQ handlers, see the new handler
before returning to the caller. If the caller is an exiting module and
is unregistering its handler, failure to wait could result in the IRQ
handler jumping into an unloaded module.
The registration path doesn't require synchronization, as it's the
caller's responsibility to not generate interrupts it cares about until
after its handler is registered.
Fixes:
f6b3c72c2366 ("x86/irq: Define a global vector for VT-d Posted-Interrupts")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <
20211009001107.3936588-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jane Malalane [Thu, 21 Oct 2021 10:47:44 +0000 (11:47 +0100)]
x86/cpu: Fix migration safety with X86_BUG_NULL_SEL
commit
415de44076640483648d6c0f6d645a9ee61328ad upstream.
Currently, Linux probes for X86_BUG_NULL_SEL unconditionally which
makes it unsafe to migrate in a virtualised environment as the
properties across the migration pool might differ.
To be specific, the case which goes wrong is:
1. Zen1 (or earlier) and Zen2 (or later) in a migration pool
2. Linux boots on Zen2, probes and finds the absence of X86_BUG_NULL_SEL
3. Linux is then migrated to Zen1
Linux is now running on a X86_BUG_NULL_SEL-impacted CPU while believing
that the bug is fixed.
The only way to address the problem is to fully trust the "no longer
affected" CPUID bit when virtualised, because in the above case it would
be clear deliberately to indicate the fact "you might migrate to
somewhere which has this behaviour".
Zen3 adds the NullSelectorClearsBase CPUID bit to indicate that loading
a NULL segment selector zeroes the base and limit fields, as well as
just attributes. Zen2 also has this behaviour but doesn't have the NSCB
bit.
[ bp: Minor touchups. ]
Signed-off-by: Jane Malalane <jane.malalane@citrix.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
CC: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20211021104744.24126-1-jane.malalane@citrix.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tom Lendacky [Fri, 15 Oct 2021 17:24:16 +0000 (12:24 -0500)]
x86/sme: Use #define USE_EARLY_PGTABLE_L5 in mem_encrypt_identity.c
commit
e7d445ab26db833d6640d4c9a08bee176777cc82 upstream.
When runtime support for converting between 4-level and 5-level pagetables
was added to the kernel, the SME code that built pagetables was updated
to use the pagetable functions, e.g. p4d_offset(), etc., in order to
simplify the code. However, the use of the pagetable functions in early
boot code requires the use of the USE_EARLY_PGTABLE_L5 #define in order to
ensure that the proper definition of pgtable_l5_enabled() is used.
Without the #define, pgtable_l5_enabled() is #defined as
cpu_feature_enabled(X86_FEATURE_LA57). In early boot, the CPU features
have not yet been discovered and populated, so pgtable_l5_enabled() will
return false even when 5-level paging is enabled. This causes the SME code
to always build 4-level pagetables to perform the in-place encryption.
If 5-level paging is enabled, switching to the SME pagetables results in
a page-fault that kills the boot.
Adding the #define results in pgtable_l5_enabled() using the
__pgtable_l5_enabled variable set in early boot and the SME code building
pagetables for the proper paging level.
Fixes:
aad983913d77 ("x86/mm/encrypt: Simplify sme_populate_pgd() and sme_populate_pgd_large()")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: <stable@vger.kernel.org> # 4.18.x
Link: https://lkml.kernel.org/r/2cb8329655f5c753905812d951e212022a480475.1634318656.git.thomas.lendacky@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Miklos Szeredi [Tue, 2 Nov 2021 10:10:37 +0000 (11:10 +0100)]
fuse: fix page stealing
commit
712a951025c0667ff00b25afc360f74e639dfabe upstream.
It is possible to trigger a crash by splicing anon pipe bufs to the fuse
device.
The reason for this is that anon_pipe_buf_release() will reuse buf->page if
the refcount is 1, but that page might have already been stolen and its
flags modified (e.g. PG_lru added).
This happens in the unlikely case of fuse_dev_splice_write() getting around
to calling pipe_buf_release() after a page has been stolen, added to the
page cache and removed from the page cache.
Fix by calling pipe_buf_release() right after the page was inserted into
the page cache. In this case the page has an elevated refcount so any
release function will know that the page isn't reusable.
Reported-by: Frank Dinoff <fdinoff@google.com>
Link: https://lore.kernel.org/r/CAAmZXrsGg2xsP1CK+cbuEMumtrqdvD-NKnWzhNcvn71RV3c1yw@mail.gmail.com/
Fixes:
dd3bb14f44a6 ("fuse: support splice() writing to fuse device")
Cc: <stable@vger.kernel.org> # v2.6.35
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
yangerkun [Fri, 3 Sep 2021 06:27:48 +0000 (14:27 +0800)]
ext4: refresh the ext4_ext_path struct after dropping i_data_sem.
commit
1811bc401aa58c7bdb0df3205aa6613b49d32127 upstream.
After we drop i_data sem, we need to reload the ext4_ext_path
structure since the extent tree can change once i_data_sem is
released.
This addresses the BUG:
[52117.465187] ------------[ cut here ]------------
[52117.465686] kernel BUG at fs/ext4/extents.c:1756!
...
[52117.478306] Call Trace:
[52117.478565] ext4_ext_shift_extents+0x3ee/0x710
[52117.479020] ext4_fallocate+0x139c/0x1b40
[52117.479405] ? __do_sys_newfstat+0x6b/0x80
[52117.479805] vfs_fallocate+0x151/0x4b0
[52117.480177] ksys_fallocate+0x4a/0xa0
[52117.480533] __x64_sys_fallocate+0x22/0x30
[52117.480930] do_syscall_64+0x35/0x80
[52117.481277] entry_SYSCALL_64_after_hwframe+0x44/0xae
[52117.481769] RIP: 0033:0x7fa062f855ca
Cc: stable@kernel.org
Link: https://lore.kernel.org/r/20210903062748.4118886-4-yangerkun@huawei.com
Signed-off-by: yangerkun <yangerkun@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
yangerkun [Fri, 3 Sep 2021 06:27:47 +0000 (14:27 +0800)]
ext4: ensure enough credits in ext4_ext_shift_path_extents
commit
4268496e48dc681cfa53b92357314b5d7221e625 upstream.
Like ext4_ext_rm_leaf, we can ensure that there are enough credits
before every call that will consume credits. As part of this fix we
fold the functionality of ext4_access_path() into
ext4_ext_shift_path_extents(). This change is needed as a preparation
for the next bugfix patch.
Cc: stable@kernel.org
Link: https://lore.kernel.org/r/20210903062748.4118886-3-yangerkun@huawei.com
Signed-off-by: yangerkun <yangerkun@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shaoying Xu [Thu, 2 Sep 2021 16:44:12 +0000 (16:44 +0000)]
ext4: fix lazy initialization next schedule time computation in more granular unit
commit
39fec6889d15a658c3a3ebb06fd69d3584ddffd3 upstream.
Ext4 file system has default lazy inode table initialization setup once
it is mounted. However, it has issue on computing the next schedule time
that makes the timeout same amount in jiffies but different real time in
secs if with various HZ values. Therefore, fix by measuring the current
time in a more granular unit nanoseconds and make the next schedule time
independent of the HZ value.
Fixes:
bfff68738f1c ("ext4: add support for lazy inode table initialization")
Signed-off-by: Shaoying Xu <shaoyi@amazon.com>
Cc: stable@vger.kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Link: https://lore.kernel.org/r/20210902164412.9994-2-shaoyi@amazon.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Whitney [Tue, 12 Oct 2021 17:19:01 +0000 (13:19 -0400)]
Revert "ext4: enforce buffer head state assertion in ext4_da_map_blocks"
commit
3eda41df05d6ad5c825cbc7fef03d563597b1afa upstream.
This reverts commit
948ca5f30e1df0c11eb5b0f410b9ceb97fa77ad9.
Two crash reports from users running variations on 5.15-rc4 kernels
suggest that it is premature to enforce the state assertion in the
original commit. Both crashes were triggered by BUG calls in that
code, indicating that under some rare circumstance the buffer head
state did not match a delayed allocated block at the time the
block was written out. No reproducer is available. Resolving this
problem will require more time than remains in the current release
cycle, so reverting the original patch for the time being is necessary
to avoid any instability it may cause.
Signed-off-by: Eric Whitney <enwlinux@gmail.com>
Link: https://lore.kernel.org/r/20211012171901.5352-1-enwlinux@gmail.com
Fixes:
948ca5f30e1d ("ext4: enforce buffer head state assertion in ext4_da_map_blocks")
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Fri, 5 Nov 2021 09:15:17 +0000 (10:15 +0100)]
ALSA: timer: Unconditionally unlink slave instances, too
commit
ffdd98277f0a1d15a67a74ae09bee713df4c0dbc upstream.
Like the previous fix (commit
c0317c0e8709 "ALSA: timer: Fix
use-after-free problem"), we have to unlink slave timer instances
immediately at snd_timer_stop(), too. Otherwise it may leave a stale
entry in the list if the slave instance is freed before actually
running.
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211105091517.21733-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wang Wensheng [Wed, 3 Nov 2021 03:35:17 +0000 (03:35 +0000)]
ALSA: timer: Fix use-after-free problem
commit
c0317c0e87094f5b5782b6fdef5ae0a4b150496c upstream.
When the timer instance was add into ack_list but was not currently in
process, the user could stop it via snd_timer_stop1() without delete it
from the ack_list. Then the user could free the timer instance and when
it was actually processed UAF occurred.
This issue could be reproduced via testcase snd_timer01 in ltp - running
several instances of that testcase at the same time.
What I actually met was that the ack_list of the timer broken and the
kernel went into deadloop with irqoff. That could be detected by
hardlockup detector on board or when we run it on qemu, we could use gdb
to dump the ack_list when the console has no response.
To fix this issue, we delete the timer instance from ack_list and
active_list unconditionally in snd_timer_stop1().
Signed-off-by: Wang Wensheng <wangwensheng4@huawei.com>
Suggested-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211103033517.80531-1-wangwensheng4@huawei.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Sun, 7 Nov 2021 16:39:11 +0000 (17:39 +0100)]
ALSA: PCM: Fix NULL dereference at mmap checks
commit
8e537d5dec34cac746dd6abf6a83e5de3aa471fc upstream.
The recent refactoring of mmap handling caused Oops on some devices
that don't use the standard memory allocations. This patch addresses
it by allowing snd_dma_buffer_mmap() helper to receive the NULL
pointer dmab argument (and return an error appropriately).
Fixes:
a202bd1ad86d ("ALSA: core: Move mmap handler into memalloc ops")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211107163911.13534-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Mon, 8 Nov 2021 14:57:52 +0000 (15:57 +0100)]
ALSA: pci: rme: Fix unaligned buffer addresses
commit
43d35ccc36dad52377dd349b2e3ea803b72c3906 upstream.
The recent fix for setting up the DMA buffer type on RME drivers tried
to address the non-standard memory managements and changed the DMA
buffer information to the standard snd_dma_buffer object that is
allocated at the probe time. However, I overlooked that the RME
drivers handle the buffer addresses based on 64k alignment, and the
previous conversion broke that silently.
This patch is an attempt to fix the regression. The snd_dma_buffer
objects are copied to the original data with the correction to the
aligned accesses, and those are passed to snd_pcm_set_runtime_buffer()
helpers instead. The original snd_dma_buffer objects are managed by
devres, hence they'll be released automagically.
Fixes:
0899a7a23047 ("ALSA: pci: rme: Set up buffer type properly")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211108145752.30572-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Austin Kim [Tue, 9 Nov 2021 00:37:42 +0000 (00:37 +0000)]
ALSA: synth: missing check for possible NULL after the call to kstrdup
commit
d159037abbe3412285c271bdfb9cdf19e62678ff upstream.
If kcalloc() return NULL due to memory starvation, it is possible for
kstrdup() to return NULL in similar case. So add null check after the call
to kstrdup() is made.
[ minor coding-style fix by tiwai ]
Signed-off-by: Austin Kim <austin.kim@lge.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211109003742.GA5423@raspberrypi
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Wed, 10 Nov 2021 19:46:33 +0000 (20:46 +0100)]
ALSA: hda: Free card instance properly at probe errors
commit
39173303c83859723dab32c2abfb97296d6af3bf upstream.
The recent change in hda-intel driver to allow repeated probes
surfaced a problem that has been hidden until; the probe process in
the work calls azx_free() at the error path, and this skips the card
free process that eventually releases codec instances. As a result,
we get a kernel WARNING like:
snd_hda_intel 0000:00:1f.3: Cannot probe codecs, giving up
------------[ cut here ]------------
WARNING: CPU: 14 PID: 186 at sound/hda/hdac_bus.c:73
....
For fixing this, we need to call snd_card_free() instead of
azx_free(). Additionally, the device drvdata has to be cleared, as
the driver binding itself is still active. Then the PM and other
driver callbacks will ignore the procedure.
Fixes:
c0f1886de7e1 ("ALSA: hda: intel: Allow repeatedly probing on codec configuration errors")
Reported-and-tested-by: Scott Branden <scott.branden@broadcom.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/063e2397-7edb-5f48-7b0d-618b938d9dd8@broadcom.com
Link: https://lore.kernel.org/r/20211110194633.19098-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexander Tsoy [Sat, 30 Oct 2021 17:43:08 +0000 (20:43 +0300)]
ALSA: usb-audio: Add registration quirk for JBL Quantum 400
commit
763d92ed5dece7d439fc28a88b2d2728d525ffd9 upstream.
Add another device ID for JBL Quantum 400. It requires the same quirk as
other JBL Quantum devices.
Signed-off-by: Alexander Tsoy <alexander@tsoy.me>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211030174308.1011825-1-alexander@tsoy.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jason Ormes [Sat, 30 Oct 2021 20:04:05 +0000 (15:04 -0500)]
ALSA: usb-audio: Line6 HX-Stomp XL USB_ID for 48k-fixed quirk
commit
8f27b689066113a3e579d4df171c980c54368c4e upstream.
Adding the Line6 HX-Stomp XL USB_ID as it needs this fixed frequency
quirk as well.
The device is basically just the HX-Stomp with some more buttons on
the face. I've done some recording with it after adding it, and it
seems to function properly with this fix. The Midi features appear to
be working as well.
[ a coding style fix and patch reformat by tiwai ]
Signed-off-by: Jason Ormes <skryking@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211030200405.1358678-1-skryking@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pavel Skripkin [Sun, 24 Oct 2021 14:03:15 +0000 (17:03 +0300)]
ALSA: mixer: fix deadlock in snd_mixer_oss_set_volume
commit
3ab7992018455ac63c33e9b3eaa7264e293e40f4 upstream.
In commit
411cef6adfb3 ("ALSA: mixer: oss: Fix racy access to slots")
added mutex protection in snd_mixer_oss_set_volume(). Second
mutex_lock() in same function looks like typo, fix it.
Reported-by: syzbot+ace149a75a9a0a399ac7@syzkaller.appspotmail.com
Fixes:
411cef6adfb3 ("ALSA: mixer: oss: Fix racy access to slots")
Cc: <stable@vger.kernel.org>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/20211024140315.16704-1-paskripkin@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Wed, 20 Oct 2021 16:48:46 +0000 (18:48 +0200)]
ALSA: mixer: oss: Fix racy access to slots
commit
411cef6adfb38a5bb6bd9af3941b28198e7fb680 upstream.
The OSS mixer can reassign the mapping slots dynamically via proc
file. Although the addition and deletion of those slots are protected
by mixer->reg_mutex, the access to slots aren't, hence this may cause
UAF when the slots in use are deleted concurrently.
This patch applies the mixer->reg_mutex in all appropriate code paths
(i.e. the ioctl functions) that may access slots.
Reported-by: syzbot+9988f17cf72a1045a189@syzkaller.appspotmail.com
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/00000000000036adc005ceca9175@google.com
Link: https://lore.kernel.org/r/20211020164846.922-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Mon, 25 Oct 2021 12:11:42 +0000 (14:11 +0200)]
ALSA: line6: fix control and interrupt message timeouts
commit
f4000b58b64344871d7b27c05e73932f137cfef6 upstream.
USB control and interrupt message timeouts are specified in milliseconds
and should specifically not vary with CONFIG_HZ.
Fixes:
705ececd1c60 ("Staging: add line6 usb driver")
Cc: stable@vger.kernel.org # 2.6.30
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211025121142.6531-3-johan@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Mon, 25 Oct 2021 12:11:41 +0000 (14:11 +0200)]
ALSA: 6fire: fix control and bulk message timeouts
commit
9b371c6cc37f954360989eec41c2ddc5a6b83917 upstream.
USB control and bulk message timeouts are specified in milliseconds and
should specifically not vary with CONFIG_HZ.
Fixes:
c6d43ba816d1 ("ALSA: usb/6fire - Driver for TerraTec DMX 6Fire USB")
Cc: stable@vger.kernel.org # 2.6.39
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211025121142.6531-2-johan@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Tue, 26 Oct 2021 09:54:01 +0000 (11:54 +0200)]
ALSA: ua101: fix division by zero at probe
commit
55f261b73a7e1cb254577c3536cef8f415de220a upstream.
Add the missing endpoint max-packet sanity check to probe() to avoid
division by zero in alloc_stream_buffers() in case a malicious device
has broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit
2548288b4fb0 ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes:
63978ab3e3e9 ("sound: add Edirol UA-101 support")
Cc: stable@vger.kernel.org # 2.6.34
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211026095401.26522-1-johan@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kai-Heng Feng [Wed, 10 Nov 2021 14:40:32 +0000 (22:40 +0800)]
ALSA: hda/realtek: Add quirk for HP EliteBook 840 G7 mute LED
commit
c058493df7edcef8f48c1494d9a84218519f966b upstream.
The mute and micmute LEDs don't work on HP EliteBook 840 G7. The same
quirk for other HP laptops can let LEDs work, so apply it.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211110144033.118451-1-kai.heng.feng@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Sun, 7 Nov 2021 08:33:39 +0000 (09:33 +0100)]
ALSA: hda/realtek: Add quirk for ASUS UX550VE
commit
4fad4fb9871b43389e4f4bead18ec693064697bb upstream.
ASUS UX550VE (SSID 1043:1970) requires a similar workaround for
managing the routing of the 4 speakers like some other ASUS models.
Add a corresponding quirk entry for fixing it.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=212641
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211107083339.18013-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jaroslav Kysela [Thu, 4 Nov 2021 15:57:26 +0000 (16:57 +0100)]
ALSA: hda/realtek: Add a quirk for Acer Spin SP513-54N
commit
2a5bb694488bb6593066d46881bfd9d07edd1628 upstream.
Another model requires ALC255_FIXUP_ACER_MIC_NO_PRESENCE fixup.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=211853
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211104155726.2090997-1-perex@perex.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jeremy Soller [Tue, 2 Nov 2021 17:21:04 +0000 (11:21 -0600)]
ALSA: hda/realtek: Headset fixup for Clevo NH77HJQ
commit
1278cc5ac2f96bab50dd55c8c05e0a6a77ce323e upstream.
On Clevo NH77HJ, NH77HP, and their 15" variants, there is a headset
microphone input attached to 0x19 that does not have a jack detect. In
order to get it working, the pin configuration needs to be set
correctly, and a new ALC256_FIXUP_SYSTEM76_MIC_NO_PRESENCE fixup is
applied. This is similar to the existing System76 quirk for ALC293, but
for ALC256.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211102172104.10610-1-tcrawford@system76.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tim Crawford [Mon, 1 Nov 2021 16:21:34 +0000 (10:21 -0600)]
ALSA: hda/realtek: Add quirk for Clevo PC70HS
commit
dbfe83507cf4ea66ce4efee2ac14c5ad420e31d3 upstream.
Apply the PB51ED PCI quirk to the Clevo PC70HS. Fixes audio output from
the internal speakers.
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211101162134.5336-1-tcrawford@system76.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Thu, 28 Oct 2021 07:09:11 +0000 (09:09 +0200)]
ALSA: hda/realtek: Add a quirk for HP OMEN 15 mute LED
commit
375f8426ed994addd2be4d76febc946a6fdd8280 upstream.
HP OMEN 15 laptop requires the quirk to fiddle with COEF 0x0b bit 2
for toggling the mute LED. It's already implemented for other HP
laptops, and we just need to add a proper fixup entry.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214735
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211028070911.18891-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johnathon Clark [Wed, 20 Oct 2021 13:12:51 +0000 (14:12 +0100)]
ALSA: hda/realtek: Fix mic mute LED for the HP Spectre x360 14
commit
5fc462c3aaad601d5089fd5588a5799896a6937d upstream.
On the 'HP Spectre x360 Convertible 14-ea0xx' the microphone mute led is
controlled by GPIO 0x04. The speaker mute LED does not seem to be
exposed by GPIO and is there not set.
[ a slight coding-style fix by tiwai ]
Fixes:
c3bb2b521944 ("ALSA: hda/realtek: Quirk for HP Spectre x360 14 amp setup")
Signed-off-by: Johnathon Clark <john.clark@cantab.net>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211020131253.35894-1-john.clark@cantab.net
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ricardo Ribalda [Fri, 18 Jun 2021 12:29:03 +0000 (14:29 +0200)]
media: v4l2-ioctl: Fix check_ext_ctrls
commit
861f92cb9160b14beef0ada047384c2340701ee2 upstream.
Drivers that do not use the ctrl-framework use this function instead.
Fix the following issues:
- Do not check for multiple classes when getting the DEF_VAL.
- Return -EINVAL for request_api calls
- Default value cannot be changed, return EINVAL as soon as possible.
- Return the right error_idx
[If an error is found when validating the list of controls passed with
VIDIOC_G_EXT_CTRLS, then error_idx shall be set to ctrls->count to
indicate to userspace that no actual hardware was touched.
It would have been much nicer of course if error_idx could point to the
control index that failed the validation, but sadly that's not how the
API was designed.]
Fixes v4l2-compliance:
Control ioctls (Input 0):
warn: v4l2-test-controls.cpp(834): error_idx should be equal to count
warn: v4l2-test-controls.cpp(855): error_idx should be equal to count
fail: v4l2-test-controls.cpp(813): doioctl(node, VIDIOC_G_EXT_CTRLS, &ctrls)
test VIDIOC_G/S/TRY_EXT_CTRLS: FAIL
Buffer ioctls (Input 0):
fail: v4l2-test-buffers.cpp(1994): ret != EINVAL && ret != EBADR && ret != ENOTTY
test Requests: FAIL
Cc: stable@vger.kernel.org
Fixes:
6fa6f831f095 ("media: v4l2-ctrls: add core request support")
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sean Young [Wed, 15 Sep 2021 16:14:07 +0000 (18:14 +0200)]
media: ir-kbd-i2c: improve responsiveness of hauppauge zilog receivers
commit
c73ba202a851c0b611ef2c25e568fadeff5e667f upstream.
The IR receiver has two issues:
- Sometimes there is no response to a button press
- Sometimes a button press is repeated when it should not have been
Hanging the polling interval fixes this behaviour.
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=994050
Cc: stable@vger.kernel.org
Suggested-by: Joaquín Alberto Calderón Pozo <kini_calderon@hotmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chen-Yu Tsai [Fri, 8 Oct 2021 10:04:23 +0000 (11:04 +0100)]
media: rkvdec: Support dynamic resolution changes
commit
0887e9e152efbd3601d6c907e90033d25067277d upstream.
The mem-to-mem stateless decoder API specifies support for dynamic
resolution changes. In particular, the decoder should accept format
changes on the OUTPUT queue even when buffers have been allocated,
as long as it is not streaming.
Relax restrictions for S_FMT as described in the previous paragraph,
and as long as the codec format remains the same. This aligns it with
the Hantro and Cedrus decoders. This change was mostly based on commit
ae02d49493b5 ("media: hantro: Fix s_fmt for dynamic resolution changes").
Since rkvdec_s_fmt() is now just a wrapper around the output/capture
variants without any additional shared functionality, drop the wrapper
and call the respective functions directly.
Fixes:
cd33c830448b ("media: rkvdec: Add the rkvdec driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sean Young [Sun, 17 Oct 2021 12:01:15 +0000 (13:01 +0100)]
media: ite-cir: IR receiver stop working after receive overflow
commit
fdc881783099c6343921ff017450831c8766d12a upstream.
On an Intel NUC6iSYK, no IR is reported after a receive overflow.
When a receiver overflow occurs, this condition is only cleared by
reading the fifo. Make sure we read anything in the fifo.
Fixes:
28c7afb07ccf ("media: ite-cir: check for receive overflow")
Suggested-by: Bryan Pass <bryan.pass@gmail.com>
Tested-by: Bryan Pass <bryan.pass@gmail.com>
Cc: stable@vger.kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chen-Yu Tsai [Fri, 8 Oct 2021 10:04:22 +0000 (11:04 +0100)]
media: rkvdec: Do not override sizeimage for output format
commit
298d8e8f7bcf023aceb60232d59b983255fec0df upstream.
The rkvdec H.264 decoder currently overrides sizeimage for the output
format. This causes issues when userspace requires and requests a larger
buffer, but ends up with one of insufficient size.
Instead, only provide a default size if none was requested. This fixes
the video_decode_accelerator_tests from Chromium failing on the first
frame due to insufficient buffer space. It also aligns the behavior
of the rkvdec driver with the Hantro and Cedrus drivers.
Fixes:
cd33c830448b ("media: rkvdec: Add the rkvdec driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tang Bin [Thu, 21 Oct 2021 01:34:22 +0000 (09:34 +0800)]
crypto: s5p-sss - Add error handling in s5p_aes_probe()
commit
a472cc0dde3eb057db71c80f102556eeced03805 upstream.
The function s5p_aes_probe() does not perform sufficient error
checking after executing platform_get_resource(), thus fix it.
Fixes:
c2afad6c6105 ("crypto: s5p-sss - Add HASH support for Exynos")
Cc: <stable@vger.kernel.org>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
jing yangyang [Fri, 20 Aug 2021 02:30:16 +0000 (19:30 -0700)]
firmware/psci: fix application of sizeof to pointer
commit
2ac5fb35cd520ab1851c9a4816c523b65276052f upstream.
sizeof when applied to a pointer typed expression gives the size of
the pointer.
./drivers/firmware/psci/psci_checker.c:158:41-47: ERROR application of sizeof to pointer
This issue was detected with the help of Coccinelle.
Fixes:
7401056de5f8 ("drivers/firmware: psci_checker: stash and use topology_core_cpumask for hotplug tests")
Cc: stable@vger.kernel.org
Reported-by: Zeal Robot <zealci@zte.com.cn>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: jing yangyang <jing.yangyang@zte.com.cn>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter [Wed, 8 Sep 2021 05:33:57 +0000 (08:33 +0300)]
tpm: Check for integer overflow in tpm2_map_response_body()
commit
a0bcce2b2a169e10eb265c8f0ebdd5ae4c875670 upstream.
The "4 * be32_to_cpu(data->count)" multiplication can potentially
overflow which would lead to memory corruption. Add a check for that.
Cc: stable@vger.kernel.org
Fixes:
745b361e989a ("tpm: infrastructure for TPM spaces")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Helge Deller [Mon, 4 Oct 2021 22:27:49 +0000 (00:27 +0200)]
parisc: Fix ptrace check on syscall return
commit
8779e05ba8aaffec1829872ef9774a71f44f6580 upstream.
The TIF_XXX flags are stored in the flags field in the thread_info
struct (TI_FLAGS), not in the flags field of the task_struct structure
(TASK_FLAGS).
It seems this bug didn't generate any important side-effects, otherwise it
wouldn't have went unnoticed for 12 years (since v2.6.32).
Signed-off-by: Helge Deller <deller@gmx.de>
Fixes:
ecd3d4bc06e48 ("parisc: stop using task->ptrace for {single,block}step flags")
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Helge Deller [Sun, 31 Oct 2021 20:58:12 +0000 (21:58 +0100)]
parisc: Fix set_fixmap() on PA1.x CPUs
commit
6e866a462867b60841202e900f10936a0478608c upstream.
Fix a kernel crash which happens on PA1.x CPUs while initializing the
FTRACE/KPROBE breakpoints. The PTE table entries for the fixmap area
were not created correctly.
Signed-off-by: Helge Deller <deller@gmx.de>
Fixes:
ccfbc68d41c2 ("parisc: add set_fixmap()/clear_fixmap()")
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pavel Begunkov [Fri, 29 Oct 2021 12:11:33 +0000 (13:11 +0100)]
io-wq: remove worker to owner tw dependency
commit
1d5f5ea7cb7d15b9fb1cc82673ebb054f02cd7d2 upstream.
INFO: task iou-wrk-6609:6612 blocked for more than 143 seconds.
Not tainted 5.15.0-rc5-syzkaller #0
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:iou-wrk-6609 state:D stack:27944 pid: 6612 ppid: 6526 flags:0x00004006
Call Trace:
context_switch kernel/sched/core.c:4940 [inline]
__schedule+0xb44/0x5960 kernel/sched/core.c:6287
schedule+0xd3/0x270 kernel/sched/core.c:6366
schedule_timeout+0x1db/0x2a0 kernel/time/timer.c:1857
do_wait_for_common kernel/sched/completion.c:85 [inline]
__wait_for_common kernel/sched/completion.c:106 [inline]
wait_for_common kernel/sched/completion.c:117 [inline]
wait_for_completion+0x176/0x280 kernel/sched/completion.c:138
io_worker_exit fs/io-wq.c:183 [inline]
io_wqe_worker+0x66d/0xc40 fs/io-wq.c:597
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295
io-wq worker may submit a task_work to the master task and upon
io_worker_exit() wait for the tw to get executed. The problem appears
when the master task is waiting in coredump.c:
468 freezer_do_not_count();
469 wait_for_completion(&core_state->startup);
470 freezer_count();
Apparently having some dependency on children threads getting everything
stuck. Workaround it by cancelling the taks_work callback that causes it
before going into io_worker_exit() waiting.
p.s. probably a better option is to not submit tw elevating the refcount
in the first place, but let's leave this excercise for the future.
Cc: stable@vger.kernel.org
Reported-and-tested-by: syzbot+27d62ee6f256b186883e@syzkaller.appspotmail.com
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/142a716f4ed936feae868959059154362bfa8c19.1635509451.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sungjong Seo [Tue, 19 Oct 2021 06:14:21 +0000 (15:14 +0900)]
exfat: fix incorrect loading of i_blocks for large files
commit
0c336d6e33f4bedc443404c89f43c91c8bd9ee11 upstream.
When calculating i_blocks, there was a mistake that was masked with a
32-bit variable. So i_blocks for files larger than 4 GiB had incorrect
values. Mask with a 64-bit variable instead of 32-bit one.
Fixes:
5f2aa075070c ("exfat: add inode operations")
Cc: stable@vger.kernel.org # v5.7+
Reported-by: Ganapathi Kamath <hgkamath@hotmail.com>
Signed-off-by: Sungjong Seo <sj1557.seo@samsung.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christian Löhle [Thu, 16 Sep 2021 05:59:19 +0000 (05:59 +0000)]
mmc: dw_mmc: Dont wait for DRTO on Write RSP error
commit
43592c8736e84025d7a45e61a46c3fa40536a364 upstream.
Only wait for DRTO on reads, otherwise the driver hangs.
The driver prevents sending CMD12 on response errors like CRCs. According
to the comment this is because some cards have problems with this during
the UHS tuning sequence. Unfortunately this workaround currently also
applies for any command with data. On reads this will set the drto timer,
which then triggers after a while. On writes this will not set any timer
and the tasklet will not be scheduled again.
I cannot test for the UHS workarounds need, but even if so, it should at
most apply to reads. I have observed many hangs when CMD25 response
contained a CRC error. This patch fixes this without touching the actual
UHS tuning workaround.
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/af8f8b8674ba4fcc9a781019e4aeb72c@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Derong Liu [Fri, 27 Aug 2021 07:15:37 +0000 (15:15 +0800)]
mmc: mtk-sd: Add wait dma stop done flow
commit
43e5fee317f4b0a48992b8b07935b1a3ac20ce84 upstream.
We found this issue on a 5G platform, during CMDQ error handling, if DMA
status is active when it call msdc_reset_hw(), it means mmc host hw reset
and DMA transfer will be parallel, mmc host may access sram region
unexpectedly. According to the programming guide of mtk-sd host, it needs
to wait for dma stop done after set dma stop.
This change should be applied to all SoCs.
Signed-off-by: Derong Liu <derong.liu@mediatek.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210827071537.1034-1-derong.liu@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ziyang Xuan [Sat, 16 Oct 2021 05:20:47 +0000 (13:20 +0800)]
char: xillybus: fix msg_ep UAF in xillyusb_probe()
commit
15c9a359094ec6251578b02387436bc64f11a477 upstream.
When endpoint_alloc() return failed in xillyusb_setup_base_eps(),
'xdev->msg_ep' will be freed but not set to NULL. That lets program
enter fail handling to cleanup_dev() in xillyusb_probe(). Check for
'xdev->msg_ep' is invalid in cleanup_dev() because 'xdev->msg_ep' did
not set to NULL when was freed. So the UAF problem for 'xdev->msg_ep'
is triggered.
==================================================================
BUG: KASAN: use-after-free in fifo_mem_release+0x1f4/0x210
CPU: 0 PID: 166 Comm: kworker/0:2 Not tainted 5.15.0-rc5+ #19
Call Trace:
dump_stack_lvl+0xe2/0x152
print_address_description.constprop.0+0x21/0x140
? fifo_mem_release+0x1f4/0x210
kasan_report.cold+0x7f/0x11b
? xillyusb_probe+0x530/0x700
? fifo_mem_release+0x1f4/0x210
fifo_mem_release+0x1f4/0x210
? __sanitizer_cov_trace_pc+0x1d/0x50
endpoint_dealloc+0x35/0x2b0
cleanup_dev+0x90/0x120
xillyusb_probe+0x59a/0x700
...
Freed by task 166:
kasan_save_stack+0x1b/0x40
kasan_set_track+0x1c/0x30
kasan_set_free_info+0x20/0x30
__kasan_slab_free+0x109/0x140
kfree+0x117/0x4c0
xillyusb_probe+0x606/0x700
Set 'xdev->msg_ep' to NULL after being freed in xillyusb_setup_base_eps()
to fix the UAF problem.
Fixes:
a53d1202aef1 ("char: xillybus: Add driver for XillyUSB (Xillybus variant for USB)")
Cc: stable <stable@vger.kernel.org>
Acked-by: Eli Billauer <eli.billauer@gmail.com>
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Link: https://lore.kernel.org/r/20211016052047.1611983-1-william.xuanziyang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ben Skeggs [Wed, 3 Nov 2021 01:10:57 +0000 (11:10 +1000)]
ce/gf100: fix incorrect CE0 address calculation on some GPUs
commit
93f43ed81abec8c805e1b77eb1d20dbc51a24dc4 upstream.
The code which constructs the modules for each engine present on the GPU
passes -1 for 'instance' on non-instanced engines, which affects how the
name for a sub-device is generated. This is then stored as 'instance 0'
in nvkm_subdev.inst, so code can potentially be shared with earlier GPUs
that only had a single instance of an engine.
However, GF100's CE constructor uses this value to calculate the address
of its falcon before it's translated, resulting in CE0 getting the wrong
address.
This slightly modifies the approach, always passing a valid instance for
engines that *can* have multiple copies, and having the code for earlier
GPUs explicitly ask for non-instanced name generation.
Bug: https://gitlab.freedesktop.org/drm/nouveau/-/issues/91
Fixes:
50551b15c760 ("drm/nouveau/ce: switch to instanced constructor")
Cc: <stable@vger.kernel.org> # v5.12+
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Tested-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211103011057.15344-1-skeggsb@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Quinn Tran [Wed, 8 Sep 2021 16:46:21 +0000 (09:46 -0700)]
scsi: qla2xxx: Fix use after free in eh_abort path
commit
3d33b303d4f3b74a71bede5639ebba3cfd2a2b4d upstream.
In eh_abort path driver prematurely exits the call to upper layer. Check
whether command is aborted / completed by firmware before exiting the call.
9 [
ffff8b1ebf803c00] page_fault at
ffffffffb0389778
[exception RIP: qla2x00_status_entry+0x48d]
RIP:
ffffffffc04fa62d RSP:
ffff8b1ebf803cb0 RFLAGS:
00010082
RAX:
00000000ffffffff RBX:
00000000000e0000 RCX:
0000000000000000
RDX:
0000000000000000 RSI:
00000000000013d8 RDI:
fffff3253db78440
RBP:
ffff8b1ebf803dd0 R8:
ffff8b1ebcd9b0c0 R9:
0000000000000000
R10:
ffff8b1e38a30808 R11:
0000000000001000 R12:
00000000000003e9
R13:
0000000000000000 R14:
ffff8b1ebcd9d740 R15:
0000000000000028
ORIG_RAX:
ffffffffffffffff CS: 0010 SS: 0018
10 [
ffff8b1ebf803cb0] enqueue_entity at
ffffffffafce708f
11 [
ffff8b1ebf803d00] enqueue_task_fair at
ffffffffafce7b88
12 [
ffff8b1ebf803dd8] qla24xx_process_response_queue at
ffffffffc04fc9a6
[qla2xxx]
13 [
ffff8b1ebf803e78] qla24xx_msix_rsp_q at
ffffffffc04ff01b [qla2xxx]
14 [
ffff8b1ebf803eb0] __handle_irq_event_percpu at
ffffffffafd50714
Link: https://lore.kernel.org/r/20210908164622.19240-10-njavali@marvell.com
Fixes:
f45bca8c5052 ("scsi: qla2xxx: Fix double scsi_done for abort path")
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Co-developed-by: David Jeffery <djeffery@redhat.com>
Signed-off-by: David Jeffery <djeffery@redhat.com>
Co-developed-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arun Easi [Wed, 8 Sep 2021 16:46:18 +0000 (09:46 -0700)]
scsi: qla2xxx: Fix kernel crash when accessing port_speed sysfs file
commit
3ef68d4f0c9e7cb589ae8b70f07d77f528105331 upstream.
Kernel crashes when accessing port_speed sysfs file. The issue happens on
a CNA when the local array was accessed beyond bounds. Fix this by changing
the lookup.
BUG: unable to handle kernel paging request at
0000000000004000
PGD 0 P4D 0
Oops: 0000 [#1] SMP PTI
CPU: 15 PID: 455213 Comm: sosreport Kdump: loaded Not tainted
4.18.0-305.7.1.el8_4.x86_64 #1
RIP: 0010:string_nocheck+0x12/0x70
Code: 00 00 4c 89 e2 be 20 00 00 00 48 89 ef e8 86 9a 00 00 4c 01
e3 eb 81 90 49 89 f2 48 89 ce 48 89 f8 48 c1 fe 30 66 85 f6 74 4f <44> 0f b6 0a
45 84 c9 74 46 83 ee 01 41 b8 01 00 00 00 48 8d 7c 37
RSP: 0018:
ffffb5141c1afcf0 EFLAGS:
00010286
RAX:
ffff8bf4009f8000 RBX:
ffff8bf4009f9000 RCX:
ffff0a00ffffff04
RDX:
0000000000004000 RSI:
ffffffffffffffff RDI:
ffff8bf4009f8000
RBP:
0000000000004000 R08:
0000000000000001 R09:
ffffb5141c1afb84
R10:
ffff8bf4009f9000 R11:
ffffb5141c1afce6 R12:
ffff0a00ffffff04
R13:
ffffffffc08e21aa R14:
0000000000001000 R15:
ffffffffc08e21aa
FS:
00007fc4ebfff700(0000) GS:
ffff8c717f7c0000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
0000000000004000 CR3:
000000edfdee6006 CR4:
00000000001706e0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
Call Trace:
string+0x40/0x50
vsnprintf+0x33c/0x520
scnprintf+0x4d/0x90
qla2x00_port_speed_show+0xb5/0x100 [qla2xxx]
dev_attr_show+0x1c/0x40
sysfs_kf_seq_show+0x9b/0x100
seq_read+0x153/0x410
vfs_read+0x91/0x140
ksys_read+0x4f/0xb0
do_syscall_64+0x5b/0x1a0
entry_SYSCALL_64_after_hwframe+0x65/0xca
Link: https://lore.kernel.org/r/20210908164622.19240-7-njavali@marvell.com
Fixes:
4910b524ac9e ("scsi: qla2xxx: Add support for setting port speed")
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arun Easi [Wed, 8 Sep 2021 16:46:16 +0000 (09:46 -0700)]
scsi: qla2xxx: Fix crash in NVMe abort path
commit
e6e22e6cc2962d3f3d71914b47f7fbc454670e8a upstream.
System crash was seen when I/O was run against an NVMe target and aborts
were occurring.
Crash stack is:
-- relevant crash stack --
BUG: kernel NULL pointer dereference, address:
0000000000000010
:
#6 [
ffffae1f8666bdd0] page_fault at
ffffffffa740122e
[exception RIP: qla_nvme_abort_work+339]
RIP:
ffffffffc0f592e3 RSP:
ffffae1f8666be80 RFLAGS:
00010297
RAX:
0000000000000000 RBX:
ffff9b581fc8af80 RCX:
ffffffffc0f83bd0
RDX:
0000000000000001 RSI:
ffff9b5839c6c7c8 RDI:
0000000008000000
RBP:
ffff9b6832f85000 R8:
ffffffffc0f68160 R9:
ffffffffc0f70652
R10:
ffffae1f862ffdc8 R11:
0000000000000300 R12:
000000000000010d
R13:
0000000000000000 R14:
ffff9b5839cea000 R15:
0ffff9b583fab170
ORIG_RAX:
ffffffffffffffff CS: 0010 SS: 0018
#7 [
ffffae1f8666be98] process_one_work at
ffffffffa6aba184
#8 [
ffffae1f8666bed8] worker_thread at
ffffffffa6aba39d
#9 [
ffffae1f8666bf10] kthread at
ffffffffa6ac06ed
The crash was due to a stale SRB structure access after it was aborted.
Fix the issue by removing stale access.
Link: https://lore.kernel.org/r/20210908164622.19240-5-njavali@marvell.com
Fixes:
2cabf10dbbe3 ("scsi: qla2xxx: Fix hang on NVMe command timeouts")
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
James Smart [Fri, 10 Sep 2021 23:31:53 +0000 (16:31 -0700)]
scsi: lpfc: Fix FCP I/O flush functionality for TMF routines
commit
cd8a36a90babf958082b87bc6b4df5dd70901eba upstream.
A prior patch inadvertently caused lpfc_sli_sum_iocb() to exclude counting
of outstanding aborted I/Os and ABORT IOCBs. Thus,
lpfc_reset_flush_io_context() called from any TMF routine does not properly
wait to flush all outstanding FCP IOCBs leading to a block layer crash on
an invalid scsi_cmnd->request pointer.
kernel BUG at ../block/blk-core.c:1489!
RIP: 0010:blk_requeue_request+0xaf/0xc0
...
Call Trace:
<IRQ>
__scsi_queue_insert+0x90/0xe0 [scsi_mod]
blk_done_softirq+0x7e/0x90
__do_softirq+0xd2/0x280
irq_exit+0xd5/0xe0
do_IRQ+0x4c/0xd0
common_interrupt+0x87/0x87
</IRQ>
Fix by separating out the LPFC_IO_FCP, LPFC_IO_ON_TXCMPLQ,
LPFC_DRIVER_ABORTED, and CMD_ABORT_XRI_CN || CMD_CLOSE_XRI_CN checks into a
new lpfc_sli_validate_fcp_iocb_for_abort() routine when determining to
build an ABORT iocb.
Restore lpfc_reset_flush_io_context() functionality by including counting
of outstanding aborted IOCBs and ABORT IOCBs in lpfc_sli_sum_iocb().
Link: https://lore.kernel.org/r/20210910233159.115896-9-jsmart2021@gmail.com
Fixes:
e1364711359f ("scsi: lpfc: Fix illegal memory access on Abort IOCBs")
Cc: <stable@vger.kernel.org> # v5.12+
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
James Smart [Fri, 10 Sep 2021 23:31:47 +0000 (16:31 -0700)]
scsi: lpfc: Don't release final kref on Fport node while ABTS outstanding
commit
982fc3965d1350d3332e04046b0e101006184ba9 upstream.
In a rarely executed path, FLOGI failure, there is a refcounting error. If
FLOGI completed with an error, typically a timeout, the initial completion
handler would remove the job reference. However, the job completion isn't
the actual end of the job/exchange as the timeout usually initiates an
ABTS, and upon that ABTS completion, a final completion is sent. The driver
removes the reference again in the final completion. Thus the imbalance.
In the buggy cases, if there was a link bounce while the delayed response
is outstanding, the fport node may be referenced again but there was no
additional reference as it is already present. The delayed completion then
occurs and removes the last reference freeing the node and causing issues
in the link up processed that is using the node.
Fix this scenario by removing the snippet that removed the reference in the
initial FLOGI completion. The bad snippet was poorly trying to identify the
FLOGI as OK to do so by realizing the node was not registered with either
SCSI or NVMe transport.
Link: https://lore.kernel.org/r/20210910233159.115896-3-jsmart2021@gmail.com
Fixes:
618e2ee146d4 ("scsi: lpfc: Fix FLOGI failure due to accessing a freed node")
Cc: <stable@vger.kernel.org> # v5.13+
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tadeusz Struk [Wed, 3 Nov 2021 17:06:59 +0000 (10:06 -0700)]
scsi: core: Remove command size deduction from scsi_setup_scsi_cmnd()
commit
703535e6ae1e94c89a9c1396b4c7b6b41160ef0c upstream.
No need to deduce command size in scsi_setup_scsi_cmnd() anymore as
appropriate checks have been added to scsi_fill_sghdr_rq() function and the
cmd_len should never be zero here. The code to do that wasn't correct
anyway, as it used uninitialized cmd->cmnd, which caused a null-ptr-deref
if the command size was zero as in the trace below. Fix this by removing
the unneeded code.
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
CPU: 0 PID: 1822 Comm: repro Not tainted 5.15.0 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-4.fc34 04/01/2014
Call Trace:
blk_mq_dispatch_rq_list+0x7c7/0x12d0
__blk_mq_sched_dispatch_requests+0x244/0x380
blk_mq_sched_dispatch_requests+0xf0/0x160
__blk_mq_run_hw_queue+0xe8/0x160
__blk_mq_delay_run_hw_queue+0x252/0x5d0
blk_mq_run_hw_queue+0x1dd/0x3b0
blk_mq_sched_insert_request+0x1ff/0x3e0
blk_execute_rq_nowait+0x173/0x1e0
blk_execute_rq+0x15c/0x540
sg_io+0x97c/0x1370
scsi_ioctl+0xe16/0x28e0
sd_ioctl+0x134/0x170
blkdev_ioctl+0x362/0x6e0
block_ioctl+0xb0/0xf0
vfs_ioctl+0xa7/0xf0
do_syscall_64+0x3d/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
---[ end trace
8b086e334adef6d2 ]---
Kernel panic - not syncing: Fatal exception
Link: https://lore.kernel.org/r/20211103170659.22151-2-tadeusz.struk@linaro.org
Fixes:
2ceda20f0a99 ("scsi: core: Move command size detection out of the fast path")
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: James E.J. Bottomley <jejb@linux.ibm.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: <linux-scsi@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Cc: <stable@vger.kernel.org> # 5.15, 5.14, 5.10
Reported-by: syzbot+5516b30f5401d4dcbcae@syzkaller.appspotmail.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tadeusz Struk <tadeusz.struk@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ewan D. Milne [Fri, 29 Oct 2021 19:43:10 +0000 (15:43 -0400)]
scsi: core: Avoid leaving shost->last_reset with stale value if EH does not run
commit
5ae17501bc62a49b0b193dcce003f16375f16654 upstream.
The changes to issue the abort from the scmd->abort_work instead of the EH
thread introduced a problem if eh_deadline is used. If aborting the
command(s) is successful, and there are never any scmds added to the
shost->eh_cmd_q, there is no code path which will reset the ->last_reset
value back to zero.
The effect of this is that after a successful abort with no EH thread
activity, a subsequent timeout, perhaps a long time later, might
immediately be considered past a user-set eh_deadline time, and the host
will be reset with no attempt at recovery.
Fix this by resetting ->last_reset back to zero in scmd_eh_abort_handler()
if it is determined that the EH thread will not run to do this.
Thanks to Gopinath Marappan for investigating this problem.
Link: https://lore.kernel.org/r/20211029194311.17504-2-emilne@redhat.com
Fixes:
e494f6a72839 ("[SCSI] improved eh timeout handler")
Cc: stable@vger.kernel.org
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / platform / kernel / linux-rpi.git / log