Maxime Ripard [Wed, 22 Mar 2023 08:51:51 +0000 (09:51 +0100)]
drm/vc4: hvs: More logging for dlist generation
DLIST generation can get pretty tricky and there's not a lot of debug in
the driver to help. Let's add a few more to track the generated DLIST
size.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Maxime Ripard [Thu, 23 Feb 2023 18:44:32 +0000 (19:44 +0100)]
drm/vc4: hdmi: Warn if writing to an unknown HDMI register
The VC4 HDMI driver has a bunch of accessors to read from a register.
The read accessor was warning when accessing an unknown register, but
the write one was just returning silently.
Let's make sure we warn also when writing to an unknown register.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Maxime Ripard [Wed, 29 Mar 2023 14:26:52 +0000 (15:26 +0100)]
drm/vc4: hdmi: Enable the audio clock
The audio clock is used by the HDMI controller driver and we were using
it to get its audio rate and compute the dividers needed to reach a
given audio sample rate.
However, we were never enabling it, which was resulting in lockups on
the BCM2712.
Fixes: 632ee3aa8786 ("drm/vc4: hdmi: Add audio-related callbacks")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Dave Stevenson [Thu, 30 Mar 2023 16:18:36 +0000 (17:18 +0100)]
drm/vc4: Fix FKMS for when the YUV chroma planes are different buffers
The code was assuming that it was a single buffer with offsets,
when kmstest uses separate buffers and 0 offsets for each plane.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dom Cobley [Thu, 13 Apr 2023 16:41:11 +0000 (17:41 +0100)]
drm/vc4: Treat zero sized destination as full screen
Kodi video planes come through with all zeros for fullscreen
Without this check, we WARN when writing width-1, height-1
to destination dlist
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Dom Cobley [Mon, 17 Apr 2023 14:21:41 +0000 (15:21 +0100)]
vc4_drv: Avoid panic when booted with no kms
If kms/fkms overlay is not present we have no matching drivers
and so match is NULL.
It is not safe to call component_master_add_with_match with a null match argument.
So don't do that
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Jonathan Bell [Fri, 15 Sep 2023 16:33:03 +0000 (17:33 +0100)]
drivers: rtc-rpi: add battery charge circuit control and readback
Parse devicetree for a charger voltage and apply it. If nonzero and a
valid voltage, the firmware will enable charging, otherwise the charger
circuit is disabled.
Add sysfs attributes to read back the supported charge voltage range,
the measured battery voltage, and the charger setpoint.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Jonathan Bell [Mon, 18 Sep 2023 15:33:06 +0000 (16:33 +0100)]
dt: bindings: update rpi-rtc binding
Add property for bcm2712 firmware RTC driver charger control
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Nick Hollinghurst [Fri, 28 Jul 2023 10:59:28 +0000 (11:59 +0100)]
media: i2c: imx296: Add 2ms delay after releasing standby
The delay seems to be required to reliably read model ID.
(The same delay is already used when starting the camera.)
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
Phil Elwell [Tue, 11 Jul 2023 09:17:29 +0000 (10:17 +0100)]
hwmon: (pwm-fan) Add fan speed register support
Some platforms include a fan-speed register that reports RPM directly
as an alternative to counting interrupts from the fan tachometer input.
Add support for reading a register at a given offset (rpm-offset) within
a block declared in another node (rpm-regmap). This indirection allows
the usual address mapping to be performed, and for address sharing with
another driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Dom Cobley [Fri, 7 Jul 2023 19:16:06 +0000 (20:16 +0100)]
dt-bindings: rtc: new binding for Raspberry Pi RTC driver
Add binding for the new RTC driver for Raspberry Pi.
This platform has an RTC managed by firmware, and this RTC
driver provides the simple mailbox interface to access it.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Dom Cobley [Fri, 7 Jul 2023 19:00:45 +0000 (20:00 +0100)]
rtc: rtc-rpi: Add simple RTC driver for Raspberry Pi
This supports setting and reading the real time clock
and supports wakeup alarms.
To support wake up alarms you want this bootloader config:
POWER_OFF_ON_HALT=1
WAKE_ON_GPIO=0
You can test with:
echo +600 | sudo tee /sys/class/rtc/rtc0/wakealarm
sudo halt
That will halt (in an almost no power state),
then wake and restart after 10 minutes.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Dom Cobley [Wed, 28 Jun 2023 15:24:29 +0000 (16:24 +0100)]
irqchip/irq-brcmstb-l2: Add config for 2711 controller
We currently see these regularly:
[ 25.157560] irq 31, desc:
00000000c15e6d2c, depth: 0, count: 0, unhandled: 0
[ 25.164658] ->handle_irq():
00000000b1775675, brcmstb_l2_intc_irq_handle+0x0/0x1a8
[ 25.172352] ->irq_data.chip():
00000000fea59f1c, gic_chip_mode1+0x0/0x108
[ 25.179166] ->action():
000000003eda6d6f
[ 25.183096] ->action->handler():
000000002c09e646, bad_chained_irq+0x0/0x58
[ 25.190084] IRQ_LEVEL set
[ 25.193142] IRQ_NOPROBE set
[ 25.196198] IRQ_NOREQUEST set
[ 25.199255] IRQ_NOTHREAD set
with:
$ cat /proc/interrupts | grep 31:
31: 1 0 0 0 GICv2 129 Level (null)
The interrupt is described in DT with IRQ_TYPE_LEVEL_HIGH
But the current compatible string uses the controller in edge triggered mode
(as that config matches our register layout).
Add a new compatible structure for level driven interrupt with our register layout.
We had already been using this compatible string in device tree, so no change needed
there.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Nick Hollinghurst [Thu, 11 May 2023 15:37:34 +0000 (16:37 +0100)]
drivers: iommu: Add BCM2712 IOMMU
Add a driver for BCM2712 IOMMUs.
There is a small driver for the Shared IOMMU TLB Cache.
Each IOMMU instance is a separate device.
IOMMUs are set up with a "pass-through" range covering
the lowest 40BGytes (which should cover all of SDRAM)
for the benefit of non-IOMMU-aware devices that share
a physical IOMMU; and translation for addresses in the
range 40GB to 42GB.
An optional parameter adds a DMA offset (which otherwise
would be lost?) to virtual addresses for DMA masters on a
bus such as PCIe.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
Dom Cobley [Wed, 24 May 2023 18:32:16 +0000 (19:32 +0100)]
dmaengine: bcm2835: Fix dma driver for BCM2835-38
The previous commit broke support on older devices.
Make the breaking parts of patch conditional on
the device being used.
Fixes: 6e1856ac7c39 ("dmaengine: bcm2835: HACK: Support DMA-Lite channels")
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Dom Cobley [Thu, 25 May 2023 13:48:28 +0000 (14:48 +0100)]
dmaengine: bcm2835: Rename to_bcm2711_cbaddr to to_40bit_cbaddr
As the shifted address also applies to bcm2712,
give the function a more specific name.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Jonathan Bell [Mon, 22 May 2023 14:31:17 +0000 (15:31 +0100)]
net: phy: broadcom: optionally enable link-down powersave based on DT
It's really a function of the board whether or not to use this feature
as it may require MAC compatibility as well as interop testing.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Maxime Ripard [Fri, 24 Feb 2023 13:12:50 +0000 (14:12 +0100)]
clk: bcm: rpi: Add disp clock
BCM2712 has an extra clock exposed by the firmware called DISP, and used
by (at least) the HVS. Let's add it to the list of clocks to register in
Linux.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Maxime Ripard [Thu, 13 Apr 2023 14:52:19 +0000 (16:52 +0200)]
dmaengine: bcm2835: HACK: Support DMA-Lite channels
The BCM2712 has a DMA-Lite controller that is basically a BCM2835-style
DMA controller that supports 40 bits DMA addresses.
We need it for HDMI audio to work, but this breaks BCM2835-38 so we
should rework this later.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Phil Elwell [Wed, 8 Mar 2023 16:53:38 +0000 (16:53 +0000)]
dmaengine: bcm2835: Add BCM2712 support
BCM2712 has 6 40-bit channels - DMA6 to DMA11. Add a new compatible
string to indicate that the current platform is BCM2712.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Jonathan Bell [Thu, 4 May 2023 14:48:53 +0000 (15:48 +0100)]
drivers: hwmon: rp1-adc: check conversion validity before supplying value
The SAR ADC architecture may complete a conversion but instability in the
comparator can corrupt the result. Such corruption is signalled in the CS
ERR bit, asserted alongside each conversion result.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Iago Toral Quiroga [Thu, 2 Mar 2023 10:56:52 +0000 (11:56 +0100)]
dt-bindings: gpu: v3d: Add BCM2712 to compatibility list
Phil Elwell [Fri, 4 Aug 2023 10:26:10 +0000 (11:26 +0100)]
drm/v3d: Improve MMU support for larger pages
The built-in MMU driver went most of the way towards supporting larger
kernel pages, but dropped the ball when it comes to calculating indexes
into the page table. Fix it.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Iago Toral Quiroga [Thu, 2 Mar 2023 10:54:45 +0000 (11:54 +0100)]
drm/v3d: add brcm,2712-v3d as a compatible V3D device
Iago Toral Quiroga [Thu, 2 Mar 2023 10:52:08 +0000 (11:52 +0100)]
drm/v3d: update UAPI to match user-space for V3D 7.x
V3D t.x takes a new parameter to configure TFU jobs that needs
to be provided by user space.
Iago Toral Quiroga [Thu, 2 Mar 2023 10:49:46 +0000 (11:49 +0100)]
drm/v3d: fix up register addresses for V3D 7.x
v2: fix kernel panic with debug-fs interface to list registers
Nick Hollinghurst [Mon, 4 Sep 2023 09:57:47 +0000 (10:57 +0100)]
spi: spi-gpio: Implement spidelay when requested bit rate <= 1 Mbps
Formerly the delay was omitted as bit-banged SPI seldom achieved
even one Mbit/s; but some modern platforms can run faster, and
some SPI devices may need to be clocked slower.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
Nick Hollinghurst [Wed, 1 Mar 2023 17:57:11 +0000 (17:57 +0000)]
spi: gpio: Fix spi-gpio to correctly implement sck-idle-input
Formerly, if configured using DT, CS GPIOs were driven from spi.c
and it was possible for CS to be asserted (low) *before* starting
to drive SCK. CS GPIOs have been brought under control of this
driver in both ACPI and DT cases, with a fixup for GPIO polarity.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
Phil Elwell [Wed, 8 Mar 2023 14:42:48 +0000 (14:42 +0000)]
soc: bcm: bcm2835-power: Add support for BCM2712
BCM2712 has a PM block but neither ASB nor RPIVID_ASB. Use the absence
of the "asb" register range to indicate BCM2712 and its different PM
register range.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Wed, 8 Mar 2023 14:27:58 +0000 (14:27 +0000)]
mfd: bcm2835-pm: Add support for BCM2712
BCM2712 lacks the "asb" and "rpivid_asb" register ranges, but still
requires the use of the bcm2835-power driver to reset the V3D block.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Thu, 2 Mar 2023 18:04:42 +0000 (18:04 +0000)]
hwmon: Add RP1 ADC and temperature driver
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Fri, 1 Sep 2023 13:07:48 +0000 (14:07 +0100)]
ASoC: bcm: Remove dependency on BCM2835 I2S
These soundcard drivers don't rely on a specific I2S interface, so
remove the dependency declarations.
See: https://github.com/raspberrypi/linux-2712/issues/111
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Fri, 21 Jul 2023 11:07:16 +0000 (12:07 +0100)]
ASOC: dwc: Fix 16-bit audio handling
IMO the Synopsys datasheet could be clearer in this area, but it seems
that the DMA data ports (DMATX and DMARX) expect left and right samples
in alternate writes; if a stereo pair is pushed in a single 32-bit
write, the upper half is ignored, leading to double speed audio with a
confused stereo image. Make sure the necessary changes happen by
updating the DMA configuration data in the hw_params method.
The set_bclk_ratio change was made at a time when it looked like it
could be causing an error, but I think the division of responsibilities
is clearer this way (and the kernel log clearer without the info-level
message).
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Mon, 3 Jul 2023 09:14:43 +0000 (10:14 +0100)]
ASOC: dwc: Improve DMA shutdown
Disabling the I2S interface with outstanding transfers prevents the
DMAC from shutting down, so keep it partially active after a stop.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Mon, 3 Jul 2023 08:08:16 +0000 (09:08 +0100)]
ASoC: dwc: Add DMACR handling
Add control of the DMACR register, which is required for paced DMA
(i.e. DREQ) support.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Thu, 4 Mar 2021 14:49:23 +0000 (14:49 +0000)]
ASoC: dwc: Support set_bclk_ratio
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Wed, 15 Feb 2023 09:46:35 +0000 (09:46 +0000)]
dt-bindings: net: cdns,macb: AXI tuning properties
Add optional properties to tune the AXI interface -
cdns,aw2w-max-pipe, cdns,ar2r-max-pipe and cdns,use-aw2b-fill.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Naushir Patuck [Tue, 14 Feb 2023 17:30:12 +0000 (17:30 +0000)]
media: rp1: Add CFE (Camera Front End) support
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Naushir Patuck [Tue, 14 Feb 2023 20:58:59 +0000 (20:58 +0000)]
v4l2: Add pisp compression format support to v4l2
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Nick Hollinghurst [Tue, 19 Sep 2023 16:54:41 +0000 (17:54 +0100)]
drm: Add RP1 VEC driver
Add support for the RP1 VEC hardware.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
Nick Hollinghurst [Tue, 19 Sep 2023 16:51:49 +0000 (17:51 +0100)]
drm: Add RP1 DPI driver
Add support for the RP1 DPI hardware.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
Nick Hollinghurst [Tue, 14 Feb 2023 14:58:33 +0000 (14:58 +0000)]
drm: Add RP1 DSI driver
Add support for the RP1 DSI hardware.
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
Phil Elwell [Tue, 14 Feb 2023 14:03:54 +0000 (14:03 +0000)]
pwm: Add support for RP1 PWM
Add a driver for the RP1 PWM block.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Tue, 29 Nov 2022 10:09:54 +0000 (10:09 +0000)]
spi: dw: Handle combined tx and rx messages
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Wed, 28 Apr 2021 16:46:01 +0000 (17:46 +0100)]
dmaengine: dw-axi-dmac: Fixes for RP1
Don't assume that DMA addresses of devices are the same as their
physical addresses - convert correctly.
The CFG2 register layout is used when there are more than 8 channels,
but also when configured for more than 16 target peripheral devices
because the index of the handshake signal has to be made wider.
Reset the DMAC on probe
The driver goes to the trouble of tracking when transfers have been
paused, but then doesn't report that state when queried.
Not having APB registers is not an error - for most use cases it's
not even of interest, it's expected. Demote the message to debug level,
which is disabled by default.
Each channel has a descriptor pool, which is shared between transfers.
It is unsafe to treat the total number of descriptors allocated from a
pool as the number allocated to a specific transfer; doing so leads
to releasing buffers that shouldn't be released and walking off the
ends of descriptor lists. Instead, give each transfer descriptor its
own count.
Support partial transfers:
Some use cases involve streaming from a device where the transfer only
proceeds when the device's FIFO occupancy exceeds a certain threshold.
In such cases (e.g. when pulling data from a UART) it is important to
know how much data has been transferred so far, in order that remaining
bytes can be read from the FIFO directly by software.
Add the necessary code to provide this "residue" value with a finer,
sub-transfer granularity.
In order to prevent the occasional byte getting stuck in the DMA
controller's internal buffers, restrict the destination memory width
to the source register width.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Fri, 4 Dec 2020 15:20:36 +0000 (15:20 +0000)]
i2c: designware: Add SMBUS quick command support
The SMBUS emulation code turns an SMBUS quick command into a zero-
length read. This controller can't do zero length accesses, but it
can do quick commands, so reverse the emulation. The alternative
would be to properly implement the SMBUS support but that is a lot
more work, and unnecessary just to get i2cdetect working.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Wed, 12 Oct 2022 13:20:07 +0000 (14:20 +0100)]
clk: rp1: Add sdio-clk driver
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Wed, 12 Oct 2022 13:07:32 +0000 (14:07 +0100)]
mmc: sdhci-of-dwcmshc: rp1 sdio changes
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Liam Fraser [Thu, 14 Mar 2019 16:01:26 +0000 (16:01 +0000)]
mmc: sdhci-of-dwcmshc: define sdio timeout clocks
Signed-off-by: Liam Fraser <liam@raspberrypi.com>
Phil Elwell [Wed, 12 Oct 2022 12:24:51 +0000 (13:24 +0100)]
serial: pl011: rp1 uart support
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Mon, 10 Oct 2022 13:21:11 +0000 (14:21 +0100)]
pinctrl: Add rp1 driver
RP1 exposes GPIOs. Add a pinctrl driver to allow control of those.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Fri, 28 Oct 2022 13:13:30 +0000 (14:13 +0100)]
dt-bindings: pinctrl: Add bindings for Raspberry Pi RP1
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Mon, 10 Oct 2022 13:25:38 +0000 (14:25 +0100)]
clk: Add rp1 clock driver
RP1 contains various PLLs and clocks for driving the hardware
blocks, so add a driver to configure these.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Fri, 28 Oct 2022 13:12:18 +0000 (14:12 +0100)]
dt-bindings: clock: Add bindings for Raspberry Pi RP1
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Mon, 10 Oct 2022 13:21:50 +0000 (14:21 +0100)]
mfd: Add rp1 driver
RP1 is a multifunction PCIe device that exposes a range of
peripherals.
Add the parent driver to manage these.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Fri, 28 Oct 2022 13:10:34 +0000 (14:10 +0100)]
dt-binding: mfd: Add binding for Raspberry Pi RP1
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Thu, 1 Sep 2022 16:51:54 +0000 (17:51 +0100)]
bcm2708_fb: Fix more build warnings
Naushir Patuck [Wed, 2 Mar 2022 16:10:50 +0000 (16:10 +0000)]
V4L2: Add PiSP compressed formats to V4L2
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Naushir Patuck [Mon, 7 Feb 2022 09:20:49 +0000 (09:20 +0000)]
V4L2: Add PiSP opaque formats to V4L2
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Jim Quinlan [Fri, 23 Jun 2023 14:40:57 +0000 (10:40 -0400)]
PCI: brcmstb: Add BCM2712 support
PCI: brcmstb: differing register offsets on 2712
pcie-brcmstb: Add 2712 bridge reset support
pcie: 2712 PORT_MASK and rescal support
pcie-brcmstb: don't alter the L1SS debug register
For reasons unknown, this disables the reference clock
pcie-brcmstb: fix BAR2 enable and window decode
Set UBUS ACCESS_EN to let inbound DMA work. Also BCM2712 has grown
an index in the inbound window size decode register.
PCIe: brcmstb: Enable support for 64 MSI-Xs
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
pcie-brcmstb: Suppress read error responses
If the link is down or the EP fails to return a read completion, the
RC's default behaviour is to return an AXI error. This causes fatal
exceptions on A76, so it's better to respond with all 1s instead.
pcie-brcmstb: increase UBUS timeout to cater for link retrain events
pcie-brcmstb: Handle additional inbound regions
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
pcie-brcmstb: Add support for external MSI controller
pcie-brcmstb: add a reasonable default traffic class to priority map
BCM2712 supports multiple traffic classes (TCs) with independent
maximally sized transfer queues for each TC. Traffic classes have no
transaction ordering requirements between them, which facilitates
out-of-order completions and arbitration between posted writes for
data streams that have no dependence on each other.
In addition to the above benefits of splitting endpoint traffic into
individual queues, priorities can be assigned to traffic classes by
a heuristic or deterministic mechanism. The heuristic elevates AXI
QOS priority in accordance with the number of pending transfers in
each TC's queue, but for true priority signalling a forwarding
mechanism using vendor-defined messages is implemented.
Receipt of a 3 DWORD VDM assigns a priority tag to a TC on-the-fly,
and this tag corresponds to a configurable AXI QOS value.
As a simple baseline, assign a linear map of AXI QOS to each tag.
pcie: brcmstb: set up the VDM forwarding interface when setting up QoS
pcie-brcmstb: clean up debug messages
pcie-brcmstb: fix BCM2712A0 PHY PM errata
The power management clock is 54MHz not 50MHz, so adjust the PM clock period
to suit. Powering off the PHY PLL in L1.2 is unsafe, so force it on.
pcie-brcmstb: set CLKREQ functionality according to link partner support
The RC supports either L1 with clock PM or L1 sub-state control, not both
at the same time. Examine the link partner's capabilities to determine
which is the most suitable scheme to use.
pcie: brcmstb: don't reset block bridges in suspend or removal cases
BCM2712 has a single rescal block for all three root complexes, and
holding PCIE1's bridge in reset will hang the chip if a different
RC wants to access any of the rescal registers.
pcie: brcmstb: guard 2712-specific setup with a RC type check
BCM2711 doesn't implement the UBUS control registers.
pcie: brcmstb: On 2712 keeping the PLL powered in L1.x is not required
A separate misconfiguration when enabling SSC (the MDIO registers no
longer do the same thing on BCM2712) had the side-effect of breaking
PLL powerdown and resume sequencing.
Allow entry into a true L1.2 state where analogue is depowered.
pcie: brcmstb: Fix reset warning on probe failure
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
bcm2712: pcie: adjust PHY PLL setup to use a 54MHz input refclk
Use canned MDIO writes from Broadcom that switch the ref_clk output
pair to run from the internal fractional PLL, and set the internal PLL
to expect a 54MHz input reference clock.
Gen3 operation is not guaranteed to be stable in this setup, so default
to gen2.
This only works if the LCPLL is bypassed (requires latest bootloader).
pcie: brcmstb: add missing register writes
drivers: pcie: brcmstb: cater for BCM2712C0 bug dropping QoS on the floor
The AXI QoS value extracted from the request fifo ends up as zero forever.
Disabling this means that "panic" signalling doesn't do anything useful,
but static priorites do work.
Also align the selected TC:QoS map with RP1's expectations of service.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
drivers: pcie: brcmstb: shuffle TC priorities up to 8
Use the range 8-11 which puts the highest below HVS but leaves space
below for other 2712 masters.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
drivers: pcie: brcmstb: optionally enable QoS features by DT for BCM2712
It's a bad idea to universally enable "realtime" priorities for TCs
across all the RC instances on the chip. Endpoints other than RP1 may
make use of these, so you don't want e.g. NVMe descriptor fetches getting
higher priority than your remote display.
Add two optional DT properties controlling the behaviour - FIFO-based
backpressure QoS or "message-based". Message-based signalling is
fundamentally broken due to a chip bug, so it collapses into a set of
static assignments that RP1 needs.
The default if neither property is specified is to assign everything a
QoS of 0.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
drivers: pcie: brcmstb: adjust completion timeouts for bcm2712
Setting the RC config retry timeout makes CRS auto-polling work, but
the UBUS timeout will override the config retry. Both need to be large.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Nick Hollinghurst [Wed, 1 Dec 2021 19:43:08 +0000 (19:43 +0000)]
drm/panel/raspberrypi-touchscreen: Insert more delays.
This avoids failures in cases where the panel is enabled
or re-probed very soon after being disabled or probed.
These can occur because the Atmel device can mis-behave
over I2C for a few ms after any write to the POWERON register.
Jonathan Bell [Mon, 13 Sep 2021 10:14:32 +0000 (11:14 +0100)]
usb: dwc3: Set DMA and coherent masks early
dwc3 allocates scratch and event buffers in the top-level driver. Hack the
probe function to set the DMA mask before trying to allocate these.
I think the event buffers are only used in device mode, but the scratch
buffers may be used if core hibernation is enabled.
usb: dwc3: add support for new DT quirks
Apply the optional axi-pipe-limit and dis-in-autoretry-quirk properties
during driver probe.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
phy: phy-brcm-usb: Add 2712 support
usb: dwc3: if the host controller instance number is present in DT, use it
If two instances of a dwc3 host controller are specified in devicetree,
then the probe order may be arbitrary which results in the device names
swapping on a per-boot basis.
If a "usb" alias with the instance number is specified, then use
that to construct the device name instead of autogenerating one.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
rp1 dwc3 changes
drivers: usb: dwc3: allow setting GTXTHRCFG on dwc_usb3.0 hardware
Equivalent register fields exist in the SuperSpeed Host version of the
hardware, so allow the use of TX thresholds if specified in devicetree.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
drivers: usb: dwc3: remove downstream quirk dis-in-autoretry
Upstream have unilaterally disabled the feature.
Partially reverts
6e9142a26ee0fdc3a5adc49ed6cedc0b16ec2ed1 (downstream)
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Phil Elwell [Fri, 10 Sep 2021 16:20:45 +0000 (17:20 +0100)]
net: macb: Also set DMA coherent mask
macb: Add device tree properties that allow configuration of the AXI max pipeline register
net: macb: add support for ethtool interrupt moderation configuration
Only global throttling of rx or tx by time quanta is supported.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
macb: add platform device shutdown function. Prevents AXI master over PCIE from hanging when the host is rebooted.
net: macb: increase polling interval for MDIO completion
MDIO is a slow bus (single-digit MHz). Polling at 1us intervals
is a bit aggressive, so increase to 100us as the transaction
usually takes 100-200us to complete.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
net: macb: Several patches for RP1
64-bit RX fix
Also set DMA coherent mask
Add device tree properties that allow configuration of the AXI max
pipeline register
Add support for ethtool interrupt moderation configuration
Only global throttling of rx or tx by time quanta is supported.
Add platform device shutdown function. Prevents AXI master over PCIE
from hanging when the host is rebooted.
Increase polling interval for MDIO completion
MDIO is a slow bus (single-digit MHz). Polling at 1us intervals
is a bit aggressive, so increase to 100us as the transaction
usually takes 100-200us to complete.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
net: macb: Support the phy-reset-gpios property
Allow a PHY to be reset with an optional GPIO. The reset duration can
be specified in milliseconds - the default is 10ms.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
drivers: net: macb: close device on driver shutdown
Fix some suspicious locking and instead call into macb_close, which
deregisters and frees all resources the corresponding macb_open
claimed.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
net: macb: add hack to prevent TX stalls in a quiet system
See https://github.com/raspberrypi/linux-2712/issues/89
There is some critical window during TX where a further write to the
TSTART bit while TX is active does not cause newly queued TX descriptors
to be consumed.
For now "wait a bit, then try anyway" seems to work.
Requires further investigation, but this unsticks NFS reliably.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
net: macb: set default interrupt moderation for GEM hardware
Defaulting to intmod = 0 is antisocial, as the MAC can generate over
130,000 interrupts per second. 50us is a sensible default.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Phil Elwell [Tue, 7 Sep 2021 13:49:00 +0000 (14:49 +0100)]
reset: reset-brcmstb-rescal: Support shared use
reset_control_reset should not be used with shared reset controllers.
Add support for reset_control_assert and _deassert to get the desired
behaviour and avoid ugly warnings in the kernel log.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Wed, 28 Jul 2021 10:13:39 +0000 (11:13 +0100)]
irqchip: irq-bcm2712-mip: Support for 2712's MIP
irqchip: irq-bcm2712-mip: specify bitmap search size as ilog2(N) not N
Freeing also has the same interface.
irqchip: irq-bcm2712-mip: Fix build warnings
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
irqchip: bcm2712-mip: add a quick hack to optionally shift MSI vectors
There are two MIP peripherals in bcm2712, the first gets a first-class
treatment where 64 consecutive GIC SPIs are assigned to all 64 output
vectors. The second gets an agglomeration of 17 GIC SPIs, but only 8 of
these are consecutive starting at the 8th output vector.
For now, allow the use of this smaller contiguous range within a larger
whole.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Nick Hollinghurst [Wed, 14 Jul 2021 08:32:49 +0000 (09:32 +0100)]
Add new "pispbe" driver (though not yet the Makesfiles or DT required to use it)
media: bcm2712: Initial commit of the PiSP BE driver
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: bcm2712_pisp_be: PiSP driver updates.
- Start registering video nodes from /dev/video20
- Formatting fixes
- Define MODULE_DEVICE_TABLE() to probe correctly
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: pisp_be: Improve image format support
Add a new format table that lists the V4L2 format enums and their properties.
Keep the exising 'RPBP' format to support the userland verification tools.
This format requires userland to fill all plane properties. Standard V4L2
formats will derive these properties from the format table.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: pisp_be: Advertise the meta output format explictily.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: pisp_be: Various updates and cleanups
- Switch to a single node group for now.
- Add a node description table to simplify node handling.
- Switch HoG output to V4L2_CAP_META_CAPTURE type.
- Use string descriptions for node names in logging messages.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
pisp_be: Updates for libcamera usage:
- Remove indexes from device entity names
- Add enumframesize and enumfmts ioctls
- Add default format to all nodes.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
v4l2: pisp_be: Move format definitions into v4l2 core
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: raspberrypi: Move PiSP common headers to a single location
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: raspberrypi: Remove old pispbe driver.
This is now supersede by the driver in drivers/media/platform/raspberrypi/
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
PISP-BE Driver: Automate buffer-cycling for TDN and Stitch state.
Remove "tdn-input" and "stitch-input" nodes altogether (the output
nodes must still be opened and REQBUFS called with 1 or 2 buffers).
Also, a bit of tidying of buffer address handling and locking.
PISP-BE driver: Turn debug level right down to reduce overly-chatty messages
media: bcm2712: Depend on CONFIG_PM
Depend on CONFIG_PM as the driver uses the runtime_pm infrastructure.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
drivers: media: pisp_be: Move BE driver to a raspberrypi directory
Move the pisp_be driver from drivers/media/platform/raspberrypi/ to
drivers/media/platform/raspberrypi/pisp_be/. This seems the accepted
convention in the drivers/media/platform/ directory structure.
Also rename the driver module from bcm2712_pisp_be to pisp_be.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
pisp_be: Updates for libcamera streaming:
- Add some required v4l2 formats
- Add buf_prepare ioctl
- Set plane offsets correctly before reprogramming
pisp_be: Reduce logging verbosity
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
pisp_be: Add buffer timestamps
While at it, remove duplicate code when checking if the HW has completed
multiple jobs.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
pisp_be: Remove queue size allocation constraint
PISP-BE driver: Fix ISR to handle multiple done/start events.
PISP-BE: Fix variable-name shadowing bugette
PISP-BE: Support for two node groups. Reorganize the driver.
To support 2 concurrent libcamera applications, we need 2 node groups,
need to allow multiple opens of each node (because libcamera does this)
and create a separate media device per group (to support file-locking).
This triggered significant rearrangement of the driver. Some calls
that we formerly intercepted have been delegated back to v4l2/vb2.
Logging changes arising from multiple v4l2_dev. Refactored probe()
and initialization. Avoid dynamically-allocated entity name strings.
drivers: media: pisp_be: Add vidioc_enum_fmt_meta_out
This was missing in the struct v4l2_ioctl_ops definition.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: media: pispe_be: Add Bayer compressed formats
Add PiSP Bayer compressed formats to the list of supported pixel formats
for the PiSP backend driver.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: meida: pisp_be: Fix overflow in plane size calculations
The calculations for buffer plane sizes can overflow because of the
plane factor shift. Fix this by using u64 integers for the calculations.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: media: pisp_be: Use 0P3 for plane factors
Use less precision for the plane factors to avoid any nasty overflows.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: pisp: Checkpatch and coding style fixups
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
media: pisp_be: More coding style fixups
media: platform: bcm2712: pisp_be: Fix crash when buffer format not set
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
media: platform: bcm2712: pisp_be: Allow non-SRGB colour spaces on RGB outputs
Allow colour spaces other than SRGB when the output format in question
is an RGB output. This commit merely ports over existing changes from
the vc4 ISP driver.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
media: platform: bcm2712: Tweak list of BE supported image formats
Remove RGB565 and 10- and 12-bit packed raw formats, which ISP-BE
can't support for input or output. Add NV12M and NV21M which it can.
(I didn't bother adding YUV422P, which apparently is not widely used.)
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
pisp_be: Fill the hardware revision in the media entity struct
This can be used by userland to determine the hardware capabilities.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
bcm2712: Use BIT() macro
Use the BIT() macro instead of plain bit shifting.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
bcm2712: Invert condition in pispbe_schedule_internal()
Return earlier and save one indentation level
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
bcm2712: Invert condition in for loop
Save one indentation level by continuing if the node is not streaming.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
bcm2712: Do not declare a local variable
There already is a truct pispbe_node *node in the function scope.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
bcm21712: Siplify pispbe_schedule_one()
A little more verbose but easier to follow ?
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
bcm2712: Rename pispbe_schedule_all() to pispbe_schedule_any()
The pispbe_schedule_all() function name is misleading, as the function
schedule a single job from any of the node groups. Rename it.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
media: platform: bcm2712: Remove buffer auto-cycling from ISP-BE
Previously, the ISP-BE driver tried to automate "ping pong" buffers
for TDN and HDR state, but did not fully conceal them from users.
The automation has been removed: there are now separate output and
capture queues for each of TDN and Stitch, which must be managed by
user code (DMABUFs may be used to circulate buffers between queues).
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
drivers: media: pisp_be: Cache BE config buffer vaddr
When programming a new job, we access at the config buffer, possibly
from ISR context. So fetch and the virtual address when queuing the
buffer.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: media: pisp_be: Remove all traces of ctrls and request API
These APIs are not (and will not) be used by the driver, so remove them.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: bcm2712: Replace v4l2_dbg with dev_dbg
Replace the v4l2 debug helpers with the device debug once, which are
preferred.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
media: bcm2712: Remove of_match_ptr()
The of_match_ptr() usage could cause a compiler warning if
CONFIG_OF is not enabled, as the pispbe_of_match variable would
result unused.
As the of_match_table field of struct platform_driver exists
unconditionally, drop of_match_ptr() to avoid a warning.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
drivers: media: pispbe: Add local config buffer DMA allocation
When initialiasing the driver, allocate a number of tiles + config
structures used for storing hardware config internally in the driver.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: media: pispbe: Use local config buffers
Store a copy of the config + tiles buffer locally when the buffer gets
queued. This resolves the security issue where a userland process may
modify the config buffer after it has been queued.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
drivers: media: pispbe: Validate config buffers
Perform a basic config validation on the device output nodes to ensure
the buffer size and stride values do not result in a buffer overrun.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: bcm2712: Rework probe sequence order
Rework the probe sequence to:
1) Use dev_err_probe() when failing to get clocks
2) Disable clock on error path
3) Disable the node groups if they have been enabled and
propagate the error up
Also disable clocks in the remove() function.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
media: bcm2712: Use pm_runtime_ops
Introduce usage of runtime resume and suspend operations.
The diver only uses a single clock source which is enable/disabled
at resume and suspend time.
Implement file open and release operations to control enablement of
the clock provider.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
media: bcm2712: Demote info message
Demote info message about clock enablement to dev_dbg()
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
media: bcm2712: Move pm_runtime calls to streamon/streamoff
Move the calls to pm_runtime_resume_and_get() and pm_runtime_put()
to the streamon and streamoff ioctl handlers.
Remove custom handlers for the open and close file operations and use
the framework provided helpers.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
media: bcm2712: Use pm_runtime_autosuspend()
Use the _autosuspend() version of runtime_pm_put() in order to avoid
resuming and suspending the peripheral in between streaming sessions
closely apart one from the other.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
drivers: media: pisp_be: Conditionally check buffers when preparing jobs
When preparing a job, check the global enables in the config structure
to see if the Output0/1, Tdn and Stitch blocks are enabled, and only
test for a buffer queued if they are.
This will allow userland to control the outputs selectively without
disabling/re-enabling the respective device nodes.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: bcm2712: Rework media controller registration
The current implementation register the v4l2_device and the video
devices first, then creates the media controller and manually registers
entities there.
Rework the registration procedure to first create the v4l2_device and
register the media_device with it. Then create the video nodes which
gets automatically registered in the media graph by the core.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
media: bcm2712: Create v4l2_subdev for ISP entity
Create a v4l2 subdevice to represent the PISPBE ISP entity.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
media: bcm2712: Fix v4l2-compliance warn on QUERYCAP
Fix:
warn: v4l2-compliance.cpp(669): media bus_info
'platform:
1000880000.pisp_be' differs from V4L2 bus_info
'platform:pispbe'
by populating the driver caps bus_info by using dev_name().
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
media: bcm2712: Fix v4l2-compliance warn on invalid pixfmt
The V4L2 API for the TRY_FMT/S_FMT ioctl allows the ioctl handler to
return an error code only in specific conditions. If an invalid pixel
format is supplied it should be adjusted instead of an error being
returned.
Albeit, v4l2-compliance treats this situation as a warning and not as
an error because the behaviour has been discussed in length in the past.
warn: v4l2-test-formats.cpp(794): TRY_FMT cannot handle an invalid pixelformat.
warn: v4l2-test-formats.cpp(795): This may or may not be a problem. For more information see:
warn: v4l2-test-formats.cpp(796): http://www.mail-archive.com/linux-media@vger.kernel.org/msg56550.html
VIDIOC_TRY_FMT returned -1 (Invalid argument)
Regardless of the warning vs failure decision, adjust the try_format()
function implementation to use V4L2_PIX_FMT_YUV420M as default pixel
format if the supplied one is invalid.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
media: bcm2712: Fix v4l2-compliance warn on HOG pix format
The try_format() implementation for the HOG video device node returns
an error if the supplied pixel format is not correct.
As per the video device output and capture video nodes, this contradicts
the V4L2 specification even if it is treated as a warning by
v4l2-compliance.
Fix this by forcing the buffer pixel format and size to the default
supported one. While at here, use the BIT() macro in the format
initialization function.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
media: bcm2712: Fix formats enumeration
Right now a single implementation of enum_fmt() is used for all nodes
in a group. This means that all the BE supported formats are listed for
all the nodes. This is incorrect as the meta capture and output node
formats should be restricted, and the meta formats should not be
enumerated for video output and capture devices.
Fix this by restricting the enumeration of META formats to the config
and hog nodes. Split out from the list of supported_formats the
V4L2_META_FMT_RPI_BE_CFG which is only used for the meta_out node, while
V4L2_PIX_FMT_RPI_BE is kept in the list of supported_formats as it can
be used as an opaque format for both meta_cap, video_cap and video_out
nodes.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
media: bcm2712: Minor fixes to support PiSP regression tests
Allow RGB input, not just Bayer (but only of those at once);
Allow Wallpaper image formats. XXX They are not yet size-checked;
Set "chicken bits" to test BURST_TRIM and AXI AWID/BID variation.
Convert some v4l2_err() to dev_err()
Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>
drivers: media: pisp_be: Use the maximum number of config buffers
Set PISP_BE_NUM_CONFIG_BUFFERS the the maximum number of possible
buffers. In the worst case, this overallocates config buffers, but
given their size, it's not too much of a problem.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
media: pisp_be: Fix extra PM runtime put
vidioc_streamoff callback can be called even if vidioc_streamon was
never called. The driver currently does PM runtime get/put in these
callbacks, which may lead to a put without a matching get.
Fix this by moving the PM runtime get/put to vb2_ops's start_streaming &
stop_streaming, which the framework makes sure won't get extra calls.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
drivers: media: pisp_be: Don't report V4L2_PIX_FMT_RPI_BE format
This is an internal opaque format, not to be reported in enum_fmt.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Phil Elwell [Tue, 6 Jul 2021 08:45:36 +0000 (09:45 +0100)]
sdhci: Add SD Express hook
sdhci: remove PYA0_INTR_BUG quirk. Add quirks to disable some of the higher SDR speeds at 1.8v.
Ulf Hansson [Thu, 29 Oct 2020 01:57:16 +0000 (09:57 +0800)]
mmc: brcmstb: add support for BCM2712
BCM2712 has an SD Express capable SDHCI implementation and uses
the SDIO CFG register block present on other STB chips.
Add plumbing for SD Express handover and BCM2712-specific functions.
Due to the common bus infrastructure between BCM2711 and BCM2712,
the driver also needs to implement 32-bit IO accessors.
mmc: brcmstb: override card presence if broken-cd is set
Not just if the card is declared as nonremovable.
sdhci: brcmstb: align SD express switchover with SD spec v8.00
Part 1 of the Physical specification, figure 3-24, details the switch
sequence for cards initially probed as SD. Add a missing check for DAT2
level after switching VDD2 on.
sdhci: brcmstb: clean up SD Express probe and error handling
Refactor to avoid spurious error messages in dmesg if the requisite SD
Express DT nodes aren't present.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
mmc: sdhci-brcmstb: only use the delay line PHY for tuneable speeds
The MMC core has a 200MHz core clock which allows the use of DDR50 and
below without incremental phase tuning. SDR50/SDR104 and the EMMC HS200
speeds require tuning.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Dom Cobley [Thu, 1 Jul 2021 18:21:10 +0000 (19:21 +0100)]
vc4/fkms: Remove use of SMI peripheral
Phil Elwell [Wed, 9 Jun 2021 14:48:28 +0000 (15:48 +0100)]
pinctrl: bcm2712 pinctrl/pinconf driver
pinctrl: bcm2712: Reject invalid pulls
Reject attempts to set pulls on aon-sgpios, and fix pull shift
values.
pinctrl: bcm2712: Add 7712 support, fix 2712 count
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
pinctrl-bcm2712: add EMMC pins so pulls can be set
These pins have pad controls but not mux controls. They look enough like
GPIOs to squeeze in at the end of the list though.
pinctrl: bcm2712: correct BCM2712C0 AON_GPIO pad pull control offset
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
pinctrl: bcm2712: on C0 the regular GPIO pad control register moves too
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
pinctrl: bcm2712: Implement (partially) pinconf_get
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
pinctrl: bcm2712: Convert to generic pinconf
Remove the legacy brcm,* pin configuration support and replace it with
a proper generic pinconf interface, using named functions instead of
alt function numbers. This is nicer for users, less error-prone, and
immune to some of the C0->D0 changes.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
pinctrl: bcm2712: Remove vestigial pull parameter
Now the legacy brcm, pinconf parameters are no longer supported, this
custom pin config parameter is not needed.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
pinctrl: bcm2712: Guard against bad func numbers
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
pinctrl: bcm2712: A better attempt at D0 support
The BCM2712D0 sparse pinctrl maps play havoc with the old GPIO_REGS
macro, so make the bit positions explicit. And delete the unwanted
GPIO and pinmux declarations on D0.
Note that a Pi 5 with D0 requires a separate DTS file with "bcm2712d0"
compatible strings.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
pinctrl: bcm2712: Delete base register constants
BCM2712D0 deletes many GPIOs and their associated mux and pad bits,
so much so that the offsets to the start of the pad control registers
changes. Remove the constant offsets from the *GPIO_REGS macros,
compensating by adjusting the per-GPIO values.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Thu, 27 May 2021 10:46:30 +0000 (11:46 +0100)]
Allow RESET_BRCMSTB on ARCH_BCM2835
Dom Cobley [Fri, 21 May 2021 11:33:38 +0000 (12:33 +0100)]
gpio_brcmstb: Allow to build for ARCH_BCM2835
gpio-brcmstb: Report the correct bank width
gpio: brcmstb: Use bank address as gpiochip label
If the path to the device node is used as gpiochip label then
gpio-brcmstb instances with multiple banks end up with duplicated
names. Instead, use a combination of the driver name with the physical
address of the bank, which is both unique and helpful for devmem
debugging.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
gpio: mmio: Add DIRECT mode for shared access
The generic MMIO GPIO library uses shadow registers for efficiency,
but this breaks attempts by raspi-gpio to change other GPIOs in the
same bank. Add a DIRECT mode that makes fewer assumptions about the
existing register contents, but note that genuinely simultaneous
accesses are likely to lose updates.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
gpio: brcmstb: Don't always clear interrupt mask
If the GPIO controller is not being used as an interrupt source
leave the interrupt mask register alone. On BCM2712 it might be used
to generate interrupts to the VPU firmware, and on other devices it
doesn't matter since no interrupts will be generated.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
popcornmix [Thu, 24 Sep 2020 19:13:08 +0000 (20:13 +0100)]
bcm2708_fb: Hack out dma support
Jonathan Bell [Wed, 26 Apr 2023 12:44:15 +0000 (13:44 +0100)]
drivers: char: delete bcm2835-gpiomem
This functionality is now provided by raspberrypi-gpiomem.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Dave Stevenson [Thu, 28 Sep 2023 16:12:37 +0000 (17:12 +0100)]
defconfigs: Add RASPBERRYPI_GPIOMEM as a module
This wants to be merged before
"drivers: char: delete bcm2835-gpiomem"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Jonathan Bell [Tue, 25 Apr 2023 14:52:13 +0000 (15:52 +0100)]
drivers: char: add generic gpiomem driver
Based on bcm2835-gpiomem.
We allow export of the "GPIO registers" to userspace via a chardev as
this allows for finer access control (e.g. users must be group gpio, root
not required).
This driver allows access to either rp1-gpiomem or gpiomem, depending on
which nodes are populated in devicetree.
RP1 has a different look-and-feel to BCM283x SoCs as it has split ranges
for IO controls and the parallel registered OE/IN/OUT access. To handle
this, the driver concatenates the ranges for an IO bank and the
corresponding RIO instance into a contiguous buffer.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Dom Cobley [Mon, 23 May 2022 15:56:44 +0000 (16:56 +0100)]
Revert "usb: phy: generic: Get the vbus supply"
This reverts commit
c0ea202fbc855d60bc4a0603ca52a9e80654b327.
Phil Elwell [Tue, 19 Sep 2023 19:31:34 +0000 (20:31 +0100)]
overlays: Add a sample hat_map
The HAT map is way of associating named overlays with HATs whose
EEPROMs were programmed with the contents of the overlay.
Unfortunately, change in the DT and kernel drivers has meant that some
of these embedded overlays no longer function, or even don't apply.
The HAT map is a mapping from HAT UUIDs to overlay names. If a HAT with
a listed UUID is detected, the embedded overlay is ignored and the
overlay named in the mapping is loaded in its place.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Vinay Varma [Fri, 22 Sep 2023 17:17:42 +0000 (18:17 +0100)]
media: i2c: imx219: fix binning and rate_factor for 480p and 1232p
At a high FPS with RAW10, there is frame corruption for 480p because the
rate_factor of 2 is used with the normal 2x2 bining [1]. This commit
ties the rate_factor to the selected binning mode. For the 480p mode,
analog 2x2 binning mode with a rate_factor of 2 is always used. For the
1232p mode the normal 2x2 binning mode is used for RAW10 while analog
2x2 binning mode is used for RAW8.
[1] raspberrypi#5493
Signed-off-by: Vinay Varma <varmavinaym@gmail.com>
Reworked due to upstream changes
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Naushir Patuck [Tue, 8 Feb 2022 13:49:11 +0000 (13:49 +0000)]
media: i2c: imx219: Scale the pixel clock rate for the 640x480 mode
The 640x480 mode uses a special binning mode for high framerate operation where
the pixel rate is effectively doubled. Account for this when setting up the
pixel clock rate, and applying the vblank and exposure controls.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Naushir Patuck [Fri, 10 Mar 2023 17:43:57 +0000 (17:43 +0000)]
media: imx219: Advertise embedded data node on media pad 1
This commit updates the imx219 driver to adverise support for embedded
data streams. This can then be used by the bcm2835-unicam driver, which
has recently been updated to expose the embedded data stream to
userland.
The imx219 sensor subdevice overloads the media pad to differentiate
between image stream (pad 0) and embedded data stream (pad 1) when
performing the v4l2_subdev_pad_ops functions.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Thu, 14 Sep 2023 11:23:05 +0000 (12:23 +0100)]
media: i2c: imx219: make HBLANK r/w to allow longer exposures
The HBLANK control was read-only, and always configured such
that the sensor HTS register was 3448. This limited the maximum
exposure time that could be achieved to around 1.26 secs.
Make HBLANK read/write so that the line time can be extended,
and thereby allow longer exposures (and slower frame rates).
Retain the overall HTS setting when changing modes rather than
resetting it to a default.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Phil Elwell [Mon, 18 Sep 2023 15:39:33 +0000 (16:39 +0100)]
overlays: Correct for #pwm-cells = 3
An upstream commit changed #pwm-cells for the BCM2835 PWMs to 3, so as
to accomodate the polarity. Add a zero to all references to the PWMs
to indicate normal polarity.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Thu, 14 Sep 2023 10:39:45 +0000 (11:39 +0100)]
configs: Regenerate the defconfigs
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Howard [Fri, 29 Mar 2019 10:53:14 +0000 (10:53 +0000)]
rtc: rv3028: Add backup switchover mode support
Signed-off-by: Phil Howard <phil@pimoroni.com>
Dom Cobley [Wed, 13 Sep 2023 18:54:04 +0000 (19:54 +0100)]
configs: Switch CONFIG_EMBEDDED to CONFIG_EXPERT
Dom Cobley [Wed, 13 Sep 2023 18:33:36 +0000 (19:33 +0100)]
Revert "configs: Regenerate with CONFIG_MEDIA_SUPPORT_FILTER unset"
This reverts commit
712b18d20c72f28acb25d4e3a508548453779582.
Dom Cobley [Wed, 13 Sep 2023 17:53:21 +0000 (18:53 +0100)]
bcm2835-unicam: hacks to allow it to build
media: bcm2835-unicam: Fix up async notifier usage
Fixes "
8a090fc3e549 bcm2835-unicam: hacks to allow it to build"
Dom Cobley [Wed, 13 Sep 2023 17:52:41 +0000 (18:52 +0100)]
configs: Regenerate with CONFIG_MEDIA_SUPPORT_FILTER unset
Required to enable MEDIA options like CONFIG_VIDEO_RPIVID
Dom Cobley [Wed, 13 Sep 2023 17:06:19 +0000 (18:06 +0100)]
Revert "drivers: char: add chardev for mmap'ing the RPiVid control registers"
This reverts commit
239b2f31fe443adfaf7f3d4b9eb7786b455b9b75.
Dave Stevenson [Fri, 1 Sep 2023 11:23:30 +0000 (12:23 +0100)]
input: ads7846: Add missing spi_device_id strings
The SPI core logs error messages if a compatible string device
name is not also present as an spi_device_id.
No spi_device_id values are specified by the driver, therefore
we get 4 log lines every time it is loaded:
SPI driver ads7846 has no spi_device_id for ti,tsc2046
SPI driver ads7846 has no spi_device_id for ti,ads7843
SPI driver ads7846 has no spi_device_id for ti,ads7845
SPI driver ads7846 has no spi_device_id for ti,ads7873
Add the spi_device_id values for these devices.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Fri, 1 Sep 2023 11:17:38 +0000 (12:17 +0100)]
drm/ili9486: Resolve clash in spi_device_id names
For "Really Good Reasons" [1] the SPI core requires a match
between compatible device strings and the name in spi_device_id.
The ili9486 driver uses compatible strings "waveshare,rpi-lcd-35"
and "ozzmaker,piscreen", but "rpi-lcd-35" and "piscreen" are missing,
so add them.
Compatible string "ilitek,ili9486" is already used by
staging/fbtft/fb_ili9486, therefore leaving it present in ili9486 as an
spi_device_id causes the incorrect module to be loaded, therefore remove
this id.
[1] https://elixir.bootlin.com/linux/latest/source/drivers/spi/spi.c#L487
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Ben Benson [Fri, 21 Jul 2023 14:59:51 +0000 (15:59 +0100)]
drivers: media: imx296: Updated imx296 driver for external trigger
Updated imx296 driver to support external trigger mode via XTR pin.
Added module parameter to control this mode.
Signed-off-by: Ben Benson <ben.benson@raspberrypi.com>
Naushir Patuck [Fri, 28 Jul 2023 11:00:40 +0000 (12:00 +0100)]
drivers: media: imx296: Add standby delay during probe
Add a 2-5ms delay when coming out of standby and before reading the
sensor info register durning probe, as instructed by the datasheet. This
standby delay is already present when the sensor starts streaming.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Nicolai Buchwitz [Wed, 12 Jul 2023 09:30:42 +0000 (11:30 +0200)]
cfg80211: ship debian certificates as hex files
Loading the regulatory database from the debian files fails with
"loaded regulatory.db is malformed or signature is missing/invalid"
due to missing certificates. Add these debian-specific certificates
from upstream to fix this error. See #5536 for details.
The certificates have been imported as following:
patch -p1 <<<$(
curl https://salsa.debian.org/kernel-team/linux/-/raw/\
master/debian/patches/debian/\
wireless-add-debian-wireless-regdb-certificates.patch
)
Signed-off-by: Nicolai Buchwitz <n.buchwitz@kunbus.com>
Jonathan Bell [Thu, 1 Dec 2022 16:59:44 +0000 (16:59 +0000)]
usb: xhci: add XHCI_VLI_HUB_TT_QUIRK
The integrated USB2.0 hub in the VL805 chipset has a bug where it
incorrectly determines the remaining available frame time before the
host next sends a SOF packet with an incremented frame_number.
See the USB2.0 specification sections 11.3 and 11.14.2.3.
The hub's non-periodic TT handler can transmit the IN/OUT handshake
token too late, so a following 64-byte DATA0/1 packet causes the ACK
handshake to collide with the propagated SOF. This causes port babble.
Avoid ringing doorbells for vulnerable endpoints during uFrame 7 if the
TR is Idle to stop one source of babble. An IN transfer for a Running TR
may happen at any time, so there's not much we can do about that.
Ideally a hub firmware update to properly implement frame timeouts is
needed, and to avoid spinning for up to 125us when submitting TDs to
Idle rings.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
xhci: constrain XHCI_VLI_HUB_TT_QUIRK to old firmware versions
VLI have a firmware update for the VL805 which resolves the incorrect
frame time calculation in the hub's TT. Limit applying the quirk to
known-bad firmwares.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Jonathan Bell [Thu, 8 Sep 2022 14:50:15 +0000 (15:50 +0100)]
usb: xhci: add VLI_SS_BULK_OUT_BUG quirk
The VL805 can cause data corruption if a SS Bulk OUT endpoint enters a
flow-control condition and there are TRBs in the transfer ring that are
not an integral size of wMaxPacket and the endpoint is behind one or more
hubs.
This is frequently the case encountered when FAT32 filesystems are
present on mass-storage devices with cluster sizes of 1 sector, and the
filesystem is being written to with an aggregate of small files.
The initial implementation of this quirk separated TRBs that didn't
adhere to this limitation into two - the first a multiple of wMaxPacket
and the second the 512-byte remainder - in an attempt to force TD
fragments to align with packet boundaries. This reduced the incidence
rate of data corruption but did not resolve it.
The fix as recommended by VIA is to disable bursts if this sequence of
TRBs can occur.
Limit turning off bursts to just USB mass-storage devices by searching
the device's configuration for an interface with a class type of
USB_CLASS_MASS_STORAGE.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Jonathan Bell [Thu, 13 Jul 2023 14:06:54 +0000 (15:06 +0100)]
usb: xhci: borrow upstream TRB_FETCH quirk on VL805 hosts
This reimplements
5a57342 usb: xhci: add VLI_TRB_CACHE_BUG quirk
The downstream implementation required a fair bit of driver surgery to
allow for truncated ring segments, which needed to shrink by a small
amount to avoid the cache prefetcher from reading off the end of one
segment and into another.
An upstream implementation for a similar bug on a different controller
just doubles the size of the memory allocated for ring segments, which
is a bit more wasteful (+4K per allocation) but means less code churn.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Jonathan Bell [Mon, 26 Oct 2020 14:03:35 +0000 (14:03 +0000)]
xhci: quirks: add link TRB quirk for VL805
The VL805 controller can't cope with the TR Dequeue Pointer for an endpoint
being set to a Link TRB. The hardware-maintained endpoint context ends up
stuck at the address of the Link TRB, leading to erroneous ring expansion
events whenever the enqueue pointer wraps to the dequeue position.
If the search for the end of the current TD and ring cycle state lands on
a Link TRB, move to the next segment.
Link: https://github.com/raspberrypi/linux/issues/3919
[6.5.y Fixup - move downstream quirk bits further along]
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Jonathan Bell [Thu, 13 Jul 2023 13:43:21 +0000 (14:43 +0100)]
xhci: Use more event ring segment table entries
Users have reported log spam created by "Event Ring Full" xHC event
TRBs. These are caused by interrupt latency in conjunction with a very
busy set of devices on the bus. The errors are benign, but throughput
will suffer as the xHC will pause processing of transfers until the
event ring is drained by the kernel. Expand the number of event TRB slots
available by increasing the number of event ring segments in the ERST.
Controllers have a hardware-defined limit as to the number of ERST
entries they can process, so make the actual number in use
min(ERST_MAX_SEGS, hw_max).
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>