Ye.Li [Thu, 30 Oct 2014 10:53:49 +0000 (18:53 +0800)]
imx: mx6 sabreauto: Add board support for USB EHCI
On mx6 sabreauto board, there are two USB ports:
0: OTG
1: HOST
The EHCI driver is enabled for this board, but the IOMUX and VBUS power
control is not implemented, which cause both USB port failed to work.
This patch fix the problem by adding the board support codes.
Since the power control uses the GPIO pin from port expander MAX7310,
the PCA953X driver is enabled for accessing the MAX7310.
The ID pin of OTG Port needs to configure the GPR1 bit 13 for selecting
its daisy chain. Add a new function "imx_iomux_set_gpr_register" to
handle GPR register setting.
Signed-off-by: Ye.Li <B37916@freescale.com>
Ye.Li [Thu, 30 Oct 2014 10:30:54 +0000 (18:30 +0800)]
imx: mx6slevk: Add support for USDHC1 and USDHC3 slots
There are three SD/MMC sockets on mx6slevk boards. Implements the
full support for them.
The default boot socket is USDHC2, so the MMC environment is set
to that device.
Signed-off-by: Ye.Li <B37916@freescale.com>
Ye.Li [Thu, 30 Oct 2014 10:30:53 +0000 (18:30 +0800)]
imx: mx6sl: Add IOMUX setting for USDHC1-3
Set the USDHC1-3 IOMUX settings which are used for mx6slevk board.
Signed-off-by: Ye.Li <B37916@freescale.com>
Ye.Li [Thu, 30 Oct 2014 10:20:59 +0000 (18:20 +0800)]
imx: mx6: Enable high frequency clock source for GPT
Set the CONFIG_MXC_GPT_HCLK configuration in mx6_common.h, so that
24Mhz OSC clock source will be selected for GPT on all MX6 platforms.
Signed-off-by: Ye.Li <B37916@freescale.com>
Ye.Li [Thu, 30 Oct 2014 10:20:58 +0000 (18:20 +0800)]
imx: mx6sl: Set the preclk clock source to OSC 24Mhz
For MX6SL, uses the OSC 24Mhz as the preclk source in CCM. Align the
preclk setting with kernel.
Signed-off-by: Ye.Li <B37916@freescale.com>
Ye.Li [Thu, 30 Oct 2014 10:20:57 +0000 (18:20 +0800)]
imx: mx6: Change the get_ipg_per_clk for OSC 24Mhz source
For MX6SL and MX6SX, the perclk can come from OSC 24Mhz source. Fix
the get_ipg_per_clk function to support it.
Signed-off-by: Ye.Li <B37916@freescale.com>
Ye.Li [Thu, 30 Oct 2014 10:20:56 +0000 (18:20 +0800)]
imx: mx6sl: Add perclk_clk_sel bit define in CCM
The MX6SL has the perclk_clk_sel to select the perclk source. Add
its define in CCM
Signed-off-by: Ye.Li <B37916@freescale.com>
Ye.Li [Thu, 30 Oct 2014 10:20:55 +0000 (18:20 +0800)]
imx: gpt: Add High frequency clock source support for GPT
Introduce a new configuration "CONFIG_MXC_GPT_HCLK". When it is set,
the GPT will select a high frequency clock as clock source.
Otherwise, the GPT will stay to use 32Khz OSC as clock source.
In the implementation, since only the GPT on i.MX6 series provide the
clock source option for 24Mhz OSC. For others (only i.MX5 and i.MX6
compile the driver), if the configuration is set, the perclk will be
selected as clock source.
MX6Q/D Rev 1.0 and MX6SL are special in the implementation, because they
don't have the 24Mhz OSC clock source option, so also select the perclk
for them. For MX6SL, we will set the OSC 24Mhz to perclk in CCM, so
eventually the clock comes from OSC 24Mhz.
Signed-off-by: Ye.Li <B37916@freescale.com>
Ye.Li [Thu, 30 Oct 2014 09:54:08 +0000 (17:54 +0800)]
imximage: Fix the bootdata.size calculation
In system boot chapter of i.MX6 reference manual, the "Image Vector Table"
figure shows the bootdata.start points to the beginning of the destination
memory. It means the bootdata.size should contain the IVT offset part,
but the calculation in imximage tool does not have.
We found this issue when booting from QuadSPI NOR on i.MX6SX. The u-boot
runs into abnormal (crash or stop) after booting. After checked the destination
memory where the image is loaded to, there are hundreds of bytes at
the image end are not loaded into memory. Since there is a 4096 bytes
round in the calculation, for the booting devices using smaller IVT offset,
such as SD and SPI booting, they are not easy to reproduce.
Signed-off-by: Ye.Li <B37916@freescale.com>
Marek Vasut [Sat, 11 Oct 2014 22:00:50 +0000 (00:00 +0200)]
arm: mxs: Define bootscript env variable on m28evk
The patch below failed to define the variable, so define it
to make it consistent with M53EVK.
commit
a428ac914b2b6db851c1feac98622f2d9844db45
Author: Lothar Rubusch <lothar@denx.de>
Date: Thu Jun 26 11:01:29 2014 +0200
ARM: m28evk: Update default environment
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Soeren Moch [Fri, 24 Oct 2014 14:33:28 +0000 (16:33 +0200)]
arm: arch-mx6: typo fixes in crm_regs.h
fix typos in video pll related register names and bit defines
Signed-off-by: Soeren Moch <smoch@web.de>
Marek Vasut [Thu, 25 Sep 2014 19:13:36 +0000 (21:13 +0200)]
mtd: nand: mxs: Add ECC geometry for 2048b/112b NAND
Add ECC geometry for NAND which has 2048b pagesize and 112b OOB
size. This is for example Macronix MX30LF2G28AB chip.
Signed-off-by: Marek Vasut <marex@denx.de>
Anatolij Gustschin [Thu, 16 Oct 2014 18:37:25 +0000 (20:37 +0200)]
arm: imx6: fix typos in CCM_ANALOG_PLL_VIDEO_DENOM register name
Fix name for Video PLL denominator register.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Nikolay Dimitrov [Sun, 12 Oct 2014 10:47:51 +0000 (13:47 +0300)]
novena: Fix ethernet PHY reset sequence
This patch fixes conflict between PHY pins becoming outputs after reset and
imx6 still driving the pins. It also fixes the reset timing as recommended by
the PHY datasheet.
Signed-off-by: Nikolay Dimitrov <picmaster@mail.bg>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Christian Gmeiner [Thu, 23 Oct 2014 11:46:43 +0000 (13:46 +0200)]
ot1200: rework card detect for eMMC
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Christian Gmeiner [Thu, 23 Oct 2014 11:46:42 +0000 (13:46 +0200)]
ot1200: add support for usdhc4
On the 'mr' variant switching to 'mmc dev 1' will result
in "MMC: no card present".
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Christian Gmeiner [Thu, 23 Oct 2014 11:46:41 +0000 (13:46 +0200)]
ot1200: add feature pads
The older 'mr' variant and the generic variant of the
OT1200 differ in some places. As the name suggests the
generic variant supports more boot devices.
In order to be compatible with the 'mr' variant we define
some 'feature' GPIOs. On the 'mr' variant this pads are
not connected so we define their state with the help
of the internal pullups.
On the generic variant this GPIOs are connected and
represent the state of the hardware.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Markus Niebel [Thu, 23 Oct 2014 13:47:06 +0000 (15:47 +0200)]
tqma6: fix typo in header guard define
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Markus Niebel [Thu, 23 Oct 2014 13:47:05 +0000 (15:47 +0200)]
tqma6: fix sf detection
Commit
155fa9af95ac5be857a7327e7a968a296e60d4c8 changed the way
to define a GPIO line, which can be used to force CS high
across multiple transactions. In order to fix sf detection
change board code to make use of board_spi_cs_gpio(..).
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Fabio Estevam [Tue, 21 Oct 2014 23:14:53 +0000 (21:14 -0200)]
mx6sabresd: Add Seiko WVGA panel support
Add support for the 4.3'' Seiko WVGA parallel display.
In order to direct the splash screen to the Seiko display:
=> setenv panel SEIKO-WVGA
=> save
=> reset
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Marek Vasut [Fri, 24 Oct 2014 21:39:07 +0000 (23:39 +0200)]
ARM: mx6: Add support for Kosagi Novena
Add support for the Kosagi Novena board. Currently supported are:
- I2C busses
- FEC Ethernet
- MMC0, MMC1, Booting from MMC
- SATA
- USB ports
- USB Ethernet
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Nikolay Dimitrov <picmaster@mail.bg>
Reviewed-by: Nikolay Dimitrov <picmaster@mail.bg>
Jeroen Hofstee [Thu, 23 Oct 2014 21:02:01 +0000 (23:02 +0200)]
board: wandboard: add usb storage
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
Christian Gmeiner [Wed, 22 Oct 2014 09:55:04 +0000 (11:55 +0200)]
ot1200: add sata support
One of the possible boot devices can be sata.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Christian Gmeiner [Wed, 22 Oct 2014 09:29:51 +0000 (11:29 +0200)]
ot1200: fix sf detection
Commit
155fa9af95ac5be857a7327e7a968a296e60d4c8 changed the way
to define a GPIO line, which can be used to force CS high
across multiple transactions. In order to fix sf detection
change board code to make use of board_spi_cs_gpio(..).
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
Fabio Estevam [Mon, 22 Sep 2014 16:55:53 +0000 (13:55 -0300)]
mx6sabre_common: Add HDMI config to common code
HDMI config options can be placed into the common mx6sabre_common.h file to
avoid duplication.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fabio Estevam [Mon, 22 Sep 2014 16:55:52 +0000 (13:55 -0300)]
mx6qsabreauto: Add HDMI support
Let HDMI splash screen support work by default.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Christian Gmeiner [Tue, 7 Oct 2014 08:58:51 +0000 (10:58 +0200)]
ot1200: remove superfluous "string" tag
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Eric Nelson [Tue, 30 Sep 2014 22:40:04 +0000 (15:40 -0700)]
ARM: i.MX video: declare displays and display_count publicly
Declare displays[] and display_count in imx-common/video.h to
prevent "Should it be static?" messages when compiling board
files with "make C=1".
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Eric Nelson [Tue, 30 Sep 2014 22:40:03 +0000 (15:40 -0700)]
ARM: i.MX: provide declaration for board_spi_cs_gpio
Provide a public declaration of the board_spi_cs_gpio()
callback for i.MX SPI chip selects to prevent the warning
"Should it be static?" when compiling with "make C=1".
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Eric Nelson [Tue, 30 Sep 2014 22:40:02 +0000 (15:40 -0700)]
ARM: i.MX6: include prototype for get_board_rev()
Include <asm/bootm.h> to see the prototype for get_board_rev()
and prevent warning "Should it be static?" with "make C=1".
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Eric Nelson [Tue, 30 Sep 2014 22:40:01 +0000 (15:40 -0700)]
ARM: prevent compiler warnings from bootm.c
Without preceding declarations, "make C=1" generates
"Should it be static?" warnings for symbols
do_bootm_linux,
boot_prep_vxworks, and
boot_jump_vxworks
Include of bootm.h also identified a signature mismatch
(const on argv[]).
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tom Rini [Tue, 14 Oct 2014 08:47:15 +0000 (04:47 -0400)]
Prepare v2014.10
Signed-off-by: Tom Rini <trini@ti.com>
Hans de Goede [Mon, 13 Oct 2014 12:51:40 +0000 (14:51 +0200)]
sunxi: axp152: dcdc3 scale is 50mV / step not 25mV / step
Currently uboot wrongly uses 25mV / step for dcdc3, this is a copy and paste
error introduced when adding the axp152_mvolt_to_target during review of the
axp152.c driver. This results in u-boot setting Vddr to 2.3V instead of 1.5V.
This commit fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tom Rini [Mon, 13 Oct 2014 12:38:55 +0000 (08:38 -0400)]
Makefile: drop "tools-only" from no-dot-config-targets
With the introduction of CONFIG_LOCALVERSION support we cannot build
tools without having a config file (as we won't know our PLAIN_VERSION
until then).
Reported-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Sat, 11 Oct 2014 00:59:28 +0000 (20:59 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
Albert ARIBAUD [Fri, 10 Oct 2014 23:20:55 +0000 (01:20 +0200)]
Merge branch 'u-boot-socfpga/topic/arm/socfpga-
20141010' into 'u-boot-arm/master'
Albert ARIBAUD [Fri, 10 Oct 2014 23:20:30 +0000 (01:20 +0200)]
Merge branch 'u-boot/master' into 'u-boot-arm/master'
Marek Vasut [Thu, 9 Oct 2014 23:50:23 +0000 (01:50 +0200)]
arm: socfpga: Use EMAC1 on SoCDK
The SoCDK uses EMAC1, not EMAC0. This patch fixes the issue.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Pavel Machek [Thu, 9 Oct 2014 23:50:22 +0000 (01:50 +0200)]
arm: socfpga: add MAINTAINERS entry
Add MAINTAINERS entry.
Signed-off-by: Pavel Machek <pavel@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Jeroen Hofstee [Tue, 7 Oct 2014 20:42:27 +0000 (22:42 +0200)]
tools: compiler.h: Fix build on FreeBSD
Commit 832472 "tools: socfpga: Add socfpga preloader signing
to mkimage" added tools/socfpga.c which relies on htole32,
le32toh and friends. While compiler.h includes these protypes
for linux from endian.h, it doesn't do so for FreeBSD. Hence
include <sys/endian.h> for FreeBSD.
Cc: Marek Vasut <marex@denx.de>
CC: Tom Rini <trini@ti.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Heiko Schocher [Wed, 1 Oct 2014 05:26:06 +0000 (07:26 +0200)]
arm, at91: add generic board support for the taurus and corvus board
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Wed, 24 Sep 2014 07:35:53 +0000 (15:35 +0800)]
ARM: atmel: switch at91sam9263ek to generic board
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Andreas Bießmann [Thu, 18 Sep 2014 21:46:49 +0000 (23:46 +0200)]
sama5d3xek: run PHY's config
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Bo Shen <voice.shen@atmel.com>
Andreas Bießmann [Thu, 18 Sep 2014 21:46:48 +0000 (23:46 +0200)]
macb: simplify gmac initialisation
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Bo Shen <voice.shen@atmel.com>
Hans de Goede [Fri, 10 Oct 2014 16:30:17 +0000 (18:30 +0200)]
serial-uclass: Fix compilation error
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Khoronzhuk, Ivan [Thu, 9 Oct 2014 19:21:14 +0000 (22:21 +0300)]
ks2_evm: readme: align according to actual sources
Update readme file for Keystone II EVM boards to actual sources.
Also correct some typos. For now the Edison evaluation board is
added, README for K2E is mostly the same, so update README to
contain information also for K2E evm. Rename file to README as
it contains information for all keystone evm boards.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Murali Karicheri [Thu, 9 Oct 2014 19:20:36 +0000 (22:20 +0300)]
configs:ks2_evm: update defconfigs to support SPL
The K2HK and K2E boards support SPL by default, so add
CONFIG_SPL option. Also export CONFIG_ARM, CONFIG_ARCH_KEYSTONE
and TARGET_K2*_EVM options to spl/.config as they are the same.
So now it's convinient to build gph images using only two commands:
make k2hk_evm_defconfig
make u-boot-spi.gph
Acked-By: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Tom Rini [Fri, 10 Oct 2014 13:45:16 +0000 (09:45 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-nand-flash
Tom Rini [Fri, 3 Oct 2014 19:57:00 +0000 (15:57 -0400)]
am335x_evm: Correct BOOTCOUNT driver support
We need to set the 'BE' flag here for things to work right.
Signed-off-by: Tom Rini <trini@ti.com>
Valentin Longchamp [Fri, 3 Oct 2014 09:16:19 +0000 (11:16 +0200)]
common/board_r: remove warning in initr_mem for 64-bit phys_size_t
Since on powerpc phys_size_t can be unsigned long long, this printout
line can result in a not nice compile warning.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Simon Glass <sjg@chromium.org>
Hannes Petermaier [Fri, 3 Oct 2014 05:30:15 +0000 (07:30 +0200)]
board/BuR: fix pinmux for MII Ethernet Interface
The lines COL (collision detect) and CRS (carrier sense) needs to be connected
and muxed to the CPSW MAC for a proper function in half-duplex Mode of the
interface.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Cc: Tom Rini <trini@ti.com>
York Sun [Wed, 1 Oct 2014 15:44:55 +0000 (08:44 -0700)]
scripts/multiconfig.sh: Fix a typo
Fix the spelling of "configs".
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Jeroen Hofstee [Wed, 1 Oct 2014 15:22:58 +0000 (17:22 +0200)]
multiconfig.sh: replace GNU sed specific match
A SPL/TPL enabled target would was not recognized as
such by BSD sed, since it relies on a GNU extension.
Instead of or-ing just spell out both matches.
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Acked-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
David Müller (ELSOFT AG) [Tue, 30 Sep 2014 11:53:28 +0000 (13:53 +0200)]
VCMA9: remove EXT2 support
remove the seldomly used EXT2 support because the U-Boot binary will
not fit into the 512KiB flash otherwise.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
David Müller (ELSOFT AG) [Tue, 30 Sep 2014 11:23:54 +0000 (13:23 +0200)]
PATI: fix broken SPI access
fix broken SPI access by adding/activating BOARD_EARLY_INIT_F
functionality and calling spi_init_f() from there.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
David Müller (ELSOFT AG) [Tue, 30 Sep 2014 10:32:23 +0000 (12:32 +0200)]
PATI: convert to generic board
Signed-off-by: David Müller <d.mueller@elsoft.ch>
David Müller (ELSOFT AG) [Tue, 30 Sep 2014 10:32:22 +0000 (12:32 +0200)]
VCMA9: convert to generic board
Signed-off-by: David Müller <d.mueller@elsoft.ch>
David Müller (ELSOFT AG) [Tue, 30 Sep 2014 10:32:21 +0000 (12:32 +0200)]
MIP405: convert to generic board
Signed-off-by: David Müller <d.mueller@elsoft.ch>
David Müller (ELSOFT AG) [Tue, 30 Sep 2014 10:32:20 +0000 (12:32 +0200)]
PIP405: convert to generic board
Signed-off-by: David Müller <d.mueller@elsoft.ch>
Wolfgang Denk [Tue, 30 Sep 2014 08:44:01 +0000 (10:44 +0200)]
SPDX License cleanup for LiMon imported files
A number of network related files were imported from the LiMon
project; these contain a somewhat unclear license statement:
Copyright 1994 - 2000 Neil Russell.
(See License)
I analyzed the source code of LiMon v1.4.2 which was used for this
import. It does not contain any "License" file, but the top level
directory contains a file "COPYING", which turns out to be GPL v2
of June 1991. So it is legitimate to conclude that the LiMon derived
files are also to be released under GPLv2. Mark them as such.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Alexander Kochetkov [Mon, 29 Sep 2014 17:46:48 +0000 (21:46 +0400)]
beagleboard: Remove side effects of i2c2 pullup resisters initialization code
Fix typo of commit
d4e53f063dd25e071444b87303573e7440deeb89.
i2c2 pullup resisters are controlled by bit 0 of CONTROL_PROG_IO1.
It's value after reset is 0x00100001.
In order to clear bit 0, original code write 0xfffffffe to
CONTROL_PROG_IO1 and toggle almost all default values.
Original code affect following:
* disable i2c1 pullup resisters
* increase far end load setting for many modules
* setup invalid SC/LB combination
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
CC: Tom Rini <trini@ti.com>
CC: Steve Kipisz <s-kipisz2@ti.com>
Masahiro Yamada [Sun, 28 Sep 2014 16:38:01 +0000 (01:38 +0900)]
powerpc: mpc5xxx: remove board support for MVBC_P and MVSMR
These boards have been orphaned for more than 6 months.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Sun, 28 Sep 2014 16:38:00 +0000 (01:38 +0900)]
powerpc: mpc83xx: remove board support for MERGERBOX and MVBLM7
These boards have been orphaned for more than 6 months.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Sun, 28 Sep 2014 16:37:59 +0000 (01:37 +0900)]
powerpc: ppc4xx: remove board support for bluestone
This board has been orphaned for more than 6 months.
It is the last board defining CONFIG_APM821XX.
The code inside #ifdef CONFIG_APM821XX should be removed too.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Sun, 28 Sep 2014 16:37:58 +0000 (01:37 +0900)]
powerpc: ppc4xx: remove board support for CRAYL1
This board has been orphaned for more than 6 months.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Sun, 28 Sep 2014 16:37:57 +0000 (01:37 +0900)]
powerpc: ppc4xx: remove board support for KAREF and METROBOX
These boards have been orphaned for more than 6 months.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Fri, 26 Sep 2014 09:42:36 +0000 (18:42 +0900)]
kconfig: fix another bug of "make savedefconfig"
In some cases, the last lines of SPL or TPL are not output to a file.
The entries remaining in the "unmatched" variable must be flushed.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Khoronzhuk, Ivan [Tue, 23 Sep 2014 18:10:26 +0000 (21:10 +0300)]
ARM: keystone: clock: fix main pll ratio div definitions
The definitions for div ratio supposed to be in hex and were added
in dec by mistake.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Roger Quadros [Tue, 23 Sep 2014 15:07:04 +0000 (18:07 +0300)]
common: spl_sata: perform SCSI scan before getting device
At least on OMAP, init_sata() no longer performs scsi_scan()
so we must do it explicitly here.
Cc: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Roger Quadros [Tue, 23 Sep 2014 15:07:03 +0000 (18:07 +0300)]
ARM: OMAP5+: sata: Move scsi_scan() to the right place
scsi_scan() must be called as part of scsi_init() and not
as part of sata_init().
Signed-off-by: Roger Quadros <rogerq@ti.com>
Roger Quadros [Tue, 23 Sep 2014 15:07:02 +0000 (18:07 +0300)]
OMAP5+: sata/scsi: Implement scsi_init()
On OMAP platforms, SATA controller provides the SCSI subsystem
so implement scsi_init().
Get rid of the unnecessary sata_init() call from dra7xx-evm
and omap5-uevm board files.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Roger Quadros [Tue, 23 Sep 2014 15:07:01 +0000 (18:07 +0300)]
ahci: Don't start command DMA engine before buffers are set
The DMA/FIS buffers are set in ahci_port_start() which is called
after ahci_host_init(). So don't start the DMA engine here
(i.e. don't set FIS_RX)
This fixes the following error at kernel boot on OMAP platforms (e.g. DRA7x)
WARNING: CPU: 0 PID: 0 at drivers/bus/omap_l3_noc.c:147 l3_interrupt_handler+0x260/0x358()
44000000.ocp:L3 Custom Error: MASTER SATA TARGET GPMC (Idle): Data Access in User mode during Functional access
Signed-off-by: Roger Quadros <rogerq@ti.com>
Stefan Herbrechtsmeier [Tue, 16 Sep 2014 15:51:05 +0000 (17:51 +0200)]
omap3: overo: Fix fdtfile test
Commit
12cc54376768461533b55ada1b0b6d4979f40579 'omap3: overo: Select
fdtfile for expansion board' wrongly missed the operator in the fdtfile
test. Update the test to only overwrite an empty fdtfile environment
variable.
Signed-off-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
York Sun [Thu, 2 Oct 2014 22:20:10 +0000 (15:20 -0700)]
common/board_r: Fix booting issue on T4240QDS
Commit
294b91a5817147d4b7f47be2ac69bac2a1f26491 moved initr_malloc
earlier than initr_unlock_ram_in_cache. This causes issue on T4240.
It may be related to locked L1 d-cache and unlocked L2 cache. D-
cache could and should be unlock earlier for normal operation.
This patch moves initr_unlock_ram_in_cache before initr_malloc. It
has been verified on the following boards, in which only T4240QDS
suffered and has been since fixed: T4240QDS, T2080QDS, P5040DS,
P4080DS, MPC8572DS, MPC8536DS, MPC8641HPCN, B4860QDS.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
CC: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Ian Campbell [Fri, 3 Oct 2014 13:29:01 +0000 (14:29 +0100)]
pxe: Ensure we don't overflow bootargs
On a couple of platforms I've tripped over long PXE append lines overflowing
this array, due to having CONFIG_SYS_CBSIZE == 256. When doing preseeded Debian
installs it's pretty trivial to exceed that.
Since the symptom can be a silent hang or a crash add a check. Of course the
affected boards would also need an increased CBSIZE to actually work.
Note that due to the printing of the final bootargs string CONFIG_SYS_PBSIZE
also needs to be sufficiently large.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
[trini: Use %zd not %d in printf for all args]
Signed-off-by: Tom Rini <trini@ti.com>
Albert ARIBAUD [Fri, 10 Oct 2014 06:56:01 +0000 (08:56 +0200)]
Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'
Masahiro Yamada [Fri, 3 Oct 2014 11:03:04 +0000 (20:03 +0900)]
mtd: denali: support NAND_CMD_RNDOUT command
The function nand_flash_detect_ext_param_page() requires
NAND_CMD_RNDOUT command supported. It is necessary to detect some
types of ONFi-compliant devices. Without it, the error message
"unsupported command received 0x5" is shown.
Let's support this command on the Denali NAND controller driver.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Chin Liang See <clsee@altera.com>
Masahiro Yamada [Fri, 3 Oct 2014 11:03:03 +0000 (20:03 +0900)]
mtd: denali: fix NAND_CMD_PARAM command
NAND_CMD_PARAM (0xEC) command is not working on the Denali
NAND controller driver.
Unlike NAND_CMD_READID (0x90), when the NAND_CMD_PARAM command
is followed by an address cycle, the target device goes busy.
(R/B# is deasserted)
Wait until the parameter data are ready.
In addition, unnecessary clear_interrupts() should be removed.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Chin Liang See <clsee@altera.com>
Nikita Kiryanov [Wed, 17 Sep 2014 12:59:25 +0000 (15:59 +0300)]
compulab: eeprom: add default eeprom bus
Add default eeprom bus setting.
This addresses the trimslice compile error that was introduced
with the addition of this setting.
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Nobuhiro Iwamatsu [Thu, 7 Aug 2014 23:44:02 +0000 (08:44 +0900)]
arm: rmobile: r8a7794: Skip initialize L2 cache
rmobile/lowlevel_init_ca15.S are common in r8a7790, r8a7791 and r8a7794 of
rmobile SoCs. The initialize L2 cache in lowlevel_init_ca15.S only needed
for Cortex-A15. The r8a7794 is Cortex-A7, not Cortex-A15.
This adds Skip to initialize L2 cache when r8a7794.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Nobuhiro Iwamatsu [Thu, 7 Aug 2014 23:41:15 +0000 (08:41 +0900)]
arm: rmobile: r8a7791: Fix initialize L2 cache
rmobile/lowlevel_init_ca15.S are common in r8a7790 and r8a7791 of
rmobile SoC. But L2 cache of r8a7791 does not use L2CTLR[5].
This adds fix to set L2CTLR [5] only when the r8a7790.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Nobuhiro Iwamatsu [Thu, 7 Aug 2014 00:10:45 +0000 (09:10 +0900)]
arm: rmobile: Remove unnecessary initialization for l2ctlr
This removes duplicate initialization of l2ctlr.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Nobuhiro Iwamatsu [Wed, 30 Jul 2014 03:28:00 +0000 (12:28 +0900)]
arm: rmobile: lager: Fix CPU frequency setting
Setting to change the CPU frequency is only used version2.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Nobuhiro Iwamatsu [Tue, 29 Jul 2014 03:14:05 +0000 (12:14 +0900)]
arm: rmobile: lager: Add Qos setting for ES2
This adds support version 0.963 for ES2 of lager board.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Nobuhiro Iwamatsu [Tue, 29 Jul 2014 03:13:16 +0000 (12:13 +0900)]
arm: rmobile: lager: Update Qos setting to version 0.955
This updates QoS version 0.955 for ES1 of lager board.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Nobuhiro Iwamatsu [Thu, 24 Jul 2014 06:30:32 +0000 (15:30 +0900)]
arm: rmobile: alt: Update QoS initialization to version 0.11
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Nobuhiro Iwamatsu [Thu, 24 Jul 2014 06:28:04 +0000 (15:28 +0900)]
arm: rmobile: koelsch: Update QoS initialization to version 0.334
This update QoS version 0.334 for ES2 of R8A7791.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Nobuhiro Iwamatsu [Sun, 27 Jul 2014 23:35:05 +0000 (08:35 +0900)]
arm: rmobile: koelsch: Add CONFIG_SCIF_USE_EXT_CLK
SCIF of koelsch use external clock mode.
This enables external clock mode on koelsch board.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Nobuhiro Iwamatsu [Sun, 27 Jul 2014 23:35:05 +0000 (08:35 +0900)]
arm: rmobile: lager: Add CONFIG_SCIF_USE_EXT_CLK
SCIF of lager use external clock mode.
This enables external clock mode on lager board.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Nobuhiro Iwamatsu [Sun, 27 Jul 2014 23:11:21 +0000 (08:11 +0900)]
arm: rmobile: lager: Fix value of CONFIG_SH_SCIF_CLK_FREQ
The clock of SCIF (serial port) of lager is supplied from External
Clock. And value of clock is 14.7456MHz.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Albert ARIBAUD [Wed, 8 Oct 2014 19:20:49 +0000 (21:20 +0200)]
Merge remote-tracking branch 'u-boot-imx/master'
The single file conflict below is actually trivial.
Conflicts:
board/boundary/nitrogen6x/nitrogen6x.c
Hans de Goede [Tue, 30 Sep 2014 16:45:32 +0000 (18:45 +0200)]
sunxi: Fix gmac not working reliable on the Bananapi
In order for the gmac nic to work reliable on the Bananapi, we need to set
bits 10-12 GTXDC "GMAC Transmit Clock Delay Chain" of the GMAC clk register
(0x01c20164) to 3.
Without this about 9 out of 10 ethernet packets get lost, with this setting
there is no packet loss.
So far setting these bits is only necessary on the Bananapi, so this commit
solves this with a bit of #ifdef CONFIG_BANANAPI code. If in the future we
need to do something similar for other boards, we can create a specific
CONFIG_FOO option for this then.
Reported-by: Karsten Merker <merker@debian.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Karsten Merker <merker@debian.org>
Tested-by: Zoltan HERPAI <wigyori@openwrt.org>
Tested-by: Tony Zhang <tony.zhang@lemaker.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Przemyslaw Marczak [Tue, 23 Sep 2014 10:46:43 +0000 (12:46 +0200)]
odroid: clock: set aclk_cores to 200MHz
This change fixes suspend/resume issue in the kernel caused
by the wrong 'aclk_cores' clock value expected by the kernel.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Masahiro Yamada [Fri, 26 Sep 2014 09:54:43 +0000 (18:54 +0900)]
exynos: update maintainer of Snow and SMDK5420 board
The email address of Rajeshwari Shinde <rajeshwari.s@samsung.com>
is not working.
This commit gives Akshay the maintainership of Snow and
SMDK5420 boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Robert Baldyga [Fri, 19 Sep 2014 10:17:55 +0000 (12:17 +0200)]
armv7: s5pc1xx: improve cache handling
Move cache handling code to C file, and add enable_caches() and
disable_caches() functions.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Simon Glass [Wed, 8 Oct 2014 04:01:52 +0000 (22:01 -0600)]
exynos: Enable pre-relocation malloc()
Enable this feature to support driver model before relocation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Simon Glass [Wed, 8 Oct 2014 04:01:51 +0000 (22:01 -0600)]
samsung: Enable device tree for smdkc100
Change this board to add a device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Simon Glass [Wed, 8 Oct 2014 04:01:50 +0000 (22:01 -0600)]
samsung: Enable device tree for s5p_goni
Change this board to add a device tree.
This also adds a pinmux header file although it is not used as yet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Simon Glass [Wed, 8 Oct 2014 04:01:49 +0000 (22:01 -0600)]
config: Move smdkv310 to use common exynos4 file
Most of the smdkv310 features are common with other exynos4 boards. To
permit easier addition of driver model support, use the common file and
add a device tree file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Simon Glass [Wed, 8 Oct 2014 04:01:48 +0000 (22:01 -0600)]
config: Move arndale to use common exynos5250 file
Most of the arndale features are common with other exynos5250 boards. To
permit easier addition of driver model support, use the common file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>