Haiying Wang [Tue, 13 Jan 2009 21:29:28 +0000 (16:29 -0500)]
Some changes of TLB entry setting for MPC8572DS
- Move the TLB entry of PIXIS_BASE from TLB0 to TLB1[8], because in CAMP mode,
all the TLB0 entries will be invalidated after cpu1 brings up kernel, thus cpu0
can not access PIXIS_BASE anymore (any access will cause DataTLBError exception)
- Set CONFIG_SYS_DDR_TLB_START to 9 for MPC8572DS board.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Haiying Wang [Tue, 13 Jan 2009 21:29:22 +0000 (16:29 -0500)]
Change DDR tlb start entry to CONFIG param for 85xx
So that we can locate the DDR tlb start entry to the value other than 8. By
default, it is still 8.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Roy Zang [Fri, 9 Jan 2009 08:02:35 +0000 (16:02 +0800)]
Change PCIE1&2 deciide logic on MPC8544DS board more readable
The IO port selection for MPC8544DS board:
Port cfg_io_ports
PCIE1 0x2, 0x3, 0x4, 0x5, 0x6, 0x7
PCIE2 0x4, 0x5, 0x6, 0x7
PCIE3 0x6, 0x7
This patch changes the PCIE12 and PCIE2 logic more readable.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Roy Zang [Fri, 9 Jan 2009 08:01:52 +0000 (16:01 +0800)]
PCIE2 and PCIE3 are decided by corresponing bit in devdisr instead of PCIE1 bit
PCIE2 and PCIE3 should be decided by corresponing bit in devdisr instead of
PCIE1 bit.
On MPC8572DS board, PCIE refers to PCIE1.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Roy Zang [Fri, 9 Jan 2009 08:00:55 +0000 (16:00 +0800)]
Fix IO port selection issue on MPC8544DS and MPC8572DS boards
The IO port selection is not correct on MPC8572DS and MPC8544DS board.
This patch fixes this issue.
For MPC8572
Port cfg_io_ports
PCIE1 0x2, 0x3, 0x7, 0xb, 0xc, 0xf
PCIE2 0x3, 0x7
PCIE3 0x7
For MPC8544
Port cfg_io_ports
PCIE1 0x2, 0x3, 0x4, 0x5, 0x6, 0x7
PCIE2 0x4, 0x5, 0x6, 0x7
PCIE3 0x6, 0x7
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Becky Bruce [Thu, 4 Dec 2008 04:36:44 +0000 (22:36 -0600)]
mpc8610hpcd: Fix PCI mapping concepts
Rename _BASE to _BUS, as it's actually a PCI bus address,
separate virtual and physical addresses into _VIRT and _PHYS,
and use each appopriately. This makes the code easier to read
and understand, and facilitates mapping changes going forward.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Becky Bruce [Thu, 4 Dec 2008 04:36:26 +0000 (22:36 -0600)]
sbc8641d: Fix PCI mapping concepts
Rename _BASE to _BUS, as it's actually a PCI bus address,
separate virtual and physical addresses into _VIRT and _PHYS,
and use each appopriately. This makes the code easier to read
and understand, and facilitates mapping changes going forward.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Wolfgang Denk [Mon, 12 Jan 2009 13:50:35 +0000 (14:50 +0100)]
MPC86xx: fix build warnings
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sat, 10 Jan 2009 17:18:37 +0000 (18:18 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-blackfin
Mike Frysinger [Mon, 5 Jan 2009 21:09:44 +0000 (16:09 -0500)]
bf537-stamp/nand: fix board_nand_init prototype
The board_nand_init() function should return an int, not void.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Thu, 11 Dec 2008 12:04:48 +0000 (07:04 -0500)]
Blackfin: drop CONFIG_SPI handling in board init
The eeprom SPI init functions are duplicated as the common code already
executes these for us.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Fri, 24 Oct 2008 21:51:57 +0000 (17:51 -0400)]
Blackfin: fix out-of-tree building with ldscripts
Many of the Blackfin board linker scripts are preprocessed, so make sure we
output the linker script into the build tree rather than the source tree.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Fri, 24 Oct 2008 21:48:54 +0000 (17:48 -0400)]
Blackfin: fix linker scripts to work with --gc-sections
Make sure all .text sections get pulled in and the entry point is properly
referenced so they don't get discarded when linking with --gc-sections.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Sun, 12 Oct 2008 00:45:44 +0000 (20:45 -0400)]
Blackfin: set proper LDRFLAGS for parallel booting LDRs
In order to boot an LDR out of parallel flash, the ldr utility needs a few
flags to tell it to generate the right header.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Jean-Christophe PLAGNIOL-VILLARD [Tue, 6 Jan 2009 20:41:59 +0000 (21:41 +0100)]
at91rm9200: move define from lowlevel_init to header
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 3 Jan 2009 16:22:26 +0000 (17:22 +0100)]
m501sk: move to the common memory setup
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 3 Jan 2009 16:22:25 +0000 (17:22 +0100)]
at91rm9200: rename lowlevel init value to CONFIG_SYS_
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Nicolas Ferre [Tue, 6 Jan 2009 20:13:14 +0000 (21:13 +0100)]
at91: add at91sam9xeek board support
At91sam9xe is basically an at91sam9260 with embedded flash. We can manage
it as another entry for at91sam9260 in the Makefile.
Check documentation at :
http://www.atmel.com/dyn/products/product_card.asp?part_id=4263
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Tue, 6 Jan 2009 20:15:57 +0000 (21:15 +0100)]
fix bmp_logo.h make dependencies to allow parallel build
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 3 Jan 2009 16:22:24 +0000 (17:22 +0100)]
at91: Fix Atmel's at91sam9 boards out of tree build
introduced in commit
89a7a87f084c
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Wolfgang Denk [Tue, 30 Dec 2008 22:30:47 +0000 (23:30 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
Wolfgang Denk [Tue, 30 Dec 2008 22:28:13 +0000 (23:28 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-mips
Wolfgang Denk [Tue, 30 Dec 2008 22:25:01 +0000 (23:25 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-nand-flash
Wolfgang Denk [Tue, 30 Dec 2008 22:22:19 +0000 (23:22 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-usb
Wolfgang Denk [Tue, 30 Dec 2008 21:56:11 +0000 (22:56 +0100)]
README: update mailing list name and hits to patch submission.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Peter Tyser [Tue, 23 Dec 2008 22:32:01 +0000 (16:32 -0600)]
85xx: Enable inbound PCI config cycles for X-ES boards cleanup
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Tue, 23 Dec 2008 22:32:00 +0000 (16:32 -0600)]
XPedite5200 board support cleanup
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Jean-Christophe PLAGNIOL-VILLARD [Tue, 2 Dec 2008 20:58:04 +0000 (21:58 +0100)]
usb_kbd: fix usb_kbd_deregister when DEVICE_DEREGISTER not enable
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Remy Böhmer <linux@bohmer.net>
Trent Piepho [Wed, 3 Dec 2008 23:16:37 +0000 (15:16 -0800)]
mpc8[56]xx: Put localbus clock in sysinfo and gd
Currently MPC85xx and MPC86xx boards just calculate the localbus frequency
and print it out, but don't save it.
This changes where its calculated and stored to be more consistent with the
CPU, CCB, TB, and DDR frequencies and the MPC83xx localbus clock.
The localbus frequency is added to sysinfo and calculated when sysinfo is
set up, in cpu/mpc8[56]xx/speed.c, the same as the other frequencies are.
get_clocks() copies the frequency into the global data, as the other
frequencies are, into a new field that is only enabled for MPC85xx and
MPC86xx.
checkcpu() in cpu/mpc8[56]xx/cpu.c will print out the local bus frequency
from sysinfo, like the other frequencies, instead of calculating it on the
spot.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
Trent Piepho [Wed, 3 Dec 2008 23:16:36 +0000 (15:16 -0800)]
mpc86xx: Double local bus clock divider
The local bus clock divider should be doubled for both 8610 and 8641.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
Trent Piepho [Wed, 3 Dec 2008 23:16:35 +0000 (15:16 -0800)]
mpc8568: Double local bus clock divider
The clock divider for the MPC8568 local bus should be doubled, like the
other newer MPC85xx chips.
Since there are now more chips with a 2x divider than a 1x, and any new
85xx chips will probably be 2x, invert the sense of the #if so that it
lists the 1x chips instead of the 2x ones.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
Dave Liu [Tue, 16 Dec 2008 04:09:27 +0000 (12:09 +0800)]
85xx: Fix the boot window issue
If one custom board is using the 8MB flash, it is set
as FLASH_BASE = 0xef000000, TEXT_BASE = 0xef780000.
The current start.S code will be broken at switch_as.
It is because the TLB1[15] is set as 16MB page size,
EPN = TEXT_BASE & 0xff000000, RPN = 0xff000000.
For the 8MB flash case, the EPN = 0xefxxxxxx,
RPN = 0xffxxxxxx. Assume the virt address of switch_as
is 0xef7ff18c, the real address of the instruction at
switch_as should be 0xff7ff18c. the 0xff7ff18c is out
of the range of the default 8MB boot LAW window
0xff800000 - 0xffffffff.
So when we switch to AS1 address space at switch_as,
the core can't fetch the instruction at switch_as any
more. It will cause broken issue.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Paul Gortmaker [Thu, 11 Dec 2008 20:47:50 +0000 (15:47 -0500)]
sbc8548: use proper PHY address
The values given for the PHY address were wrong, so the code
read no valid PHY ID, and fell through to the generic PHY
support, which would work on 1000M but would not auto negotiate
down to 100M or 10M.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Paul Gortmaker [Thu, 11 Dec 2008 20:47:51 +0000 (15:47 -0500)]
sbc8548: enable command line editing by default.
Lets make things a bit more user friendly. It isn't 1985 anymore.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Paul Gortmaker [Thu, 11 Dec 2008 20:47:49 +0000 (15:47 -0500)]
sbc8548: don't enable the 3rd and 4th eTSEC
These interfaces don't have usable connectors on the board, so don't
bother enumerating or configuring them.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Haiying Wang [Wed, 3 Dec 2008 15:08:19 +0000 (10:08 -0500)]
Set IVPR to kenrel entry point in second core boot page
Assuming the OSes exception vectors start from the base of kernel address, and
the kernel physical starting address can be relocated to an non-zero address.
This patch enables the second core to have a valid IVPR for debugger before
kernel setting IVPR in CAMP mode. Otherwise, IVPR is 0x0 and it is not a valid
value for second core which runs kernel at different physical address other
than 0x0.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Trent Piepho [Wed, 3 Dec 2008 23:16:34 +0000 (15:16 -0800)]
mpc8xxx: LCRR[CLKDIV] is sometimes five bits
On newer CPUs, 8536, 8572, and 8610, the CLKDIV field of LCRR is five bits
instead of four.
In order to avoid an ifdef, LCRR_CLKDIV is set to 0x1f on all systems. It
should be safe as the fifth bit was defined as reserved and set to 0.
Code that was using a hard coded 0x0f is changed to use LCRR_CLKDIV.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
Trent Piepho [Wed, 3 Dec 2008 23:16:38 +0000 (15:16 -0800)]
mpc8[56]xx: Put localbus clock in device tree
Export the localbus frequency in the device tree, the same way the CPU, TB,
CCB, and various other frequencies are exported in their respective device
tree nodes.
Some localbus devices need this information to be programed correctly, so
it makes sense to export it along with the other frequencies.
Unfortunately, when someone wrote the localbus dts bindings, they didn't
bother to define what the "compatible" property should be. So it seems no
one was quite sure what to put in their dts files.
Based on current existing dts files in the kernel source, I've used
"fsl,pq3-localbus" and "fsl,elbc" for MPC85xx, which are used by almost all
of the 85xx devices, and are looked for by the Linux code. The eLBC is
apparently not entirely backward compatible with the pq3 LBC and so eLBC
equipped platforms like 8572 won't use pq3-localbus.
For MPC86xx, I've used "fsl,elbc" which is used by some of the 86xx systems
and is also looked for by the Linux code. On MPC8641, I've also used
"fsl,mpc8641-localbus" as it is also commonly used in dts files, some of
which don't use "fsl,elbc" or any other acceptable name to match on.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
Kumar Gala [Tue, 16 Dec 2008 20:59:22 +0000 (14:59 -0600)]
NAND FSL elbc: Use virt_to_phys to determine which bank is in use
The current code that determines which bank/chipselect is used for a
given NAND instance only worked for 32-bit addresses and assumed
a 1:1 mapping. This breaks in 36-bit physical configs.
The proper way to handle this is to use the virt_to_phys() and
BR_PHYS_ADDR() routinues to match the 34-bit lbc bus address
with the the virtual address the NAND code uses.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Scott Wood <scottwood@freescale.com>
Kumar Gala [Tue, 16 Dec 2008 20:59:21 +0000 (14:59 -0600)]
ppc: Use addrmap in virt_to_phys and map_physmem.
If we have addr map support enabled use the mapping functions to
implement virt_to_phys() and map_physmem().
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Tue, 16 Dec 2008 20:59:20 +0000 (14:59 -0600)]
85xx: Add support to populate addr map based on TLB settings
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Peter Tyser [Mon, 1 Dec 2008 19:47:13 +0000 (13:47 -0600)]
XPedite5200 board support
Initial support for Extreme Engineering Solutions XPedite5200 -
a MPC8548-based PMC single board computer.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Wed, 29 Oct 2008 17:39:27 +0000 (12:39 -0500)]
85xx: Enable inbound PCI config cycles for X-ES boards
Update X-ES Freescale boards to allow inbound PCI configuration
cycles when configured as agent/endpoint.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Wed, 17 Dec 2008 22:36:23 +0000 (16:36 -0600)]
XPedite5370 board support
Initial support for Extreme Engineering Solutions XPedite5370 -
a MPC8572-based 3U VPX single board computer with a PMC/XMC
site.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Wed, 17 Dec 2008 22:36:21 +0000 (16:36 -0600)]
Add support for PCA953x I2C gpio devices
Initial support for NXP's 4 and 8 bit I2C gpio expanders
(eg pca9537, pca9557, etc). The CONFIG_PCA953X define
enables support for the devices while the CONFIG_CMD_PCA953X
define enables the pca953x command. The CONFIG_CMD_PCA953X_INFO
define enables an 'info' sub-command which provides summary
information for the given pca953x device.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Wed, 29 Oct 2008 17:39:26 +0000 (12:39 -0500)]
pci/fsl_pci_init: Enable inbound PCI config cycles
Add fsl_pci_config_unlock() function to enable a
PCI/PCIe interface configured in agent/endpoint mode to
respond to inbound PCI configuration cycles.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Haavard Skinnemoen [Wed, 17 Dec 2008 15:43:18 +0000 (16:43 +0100)]
avr32: Remove second definition of virt_to_phys()
The second definition introduced by
65e43a1063 conflicts with the
existing one.
Also, convert the existing definition to use phys_addr_t. The volatile
qualifier is still needed due to brain damage elsewhere.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Jean-Christophe PLAGNIOL-VILLARD [Mon, 8 Sep 2008 20:27:18 +0000 (22:27 +0200)]
MIPS: qemu_mips: update doc to generate and to use qemu flash, ide file
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Jean-Christophe PLAGNIOL-VILLARD [Tue, 16 Dec 2008 21:10:31 +0000 (22:10 +0100)]
MIPS: qemu_mips: update doc to use all disk and boot linux kernel
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Jean-Christophe PLAGNIOL-VILLARD [Tue, 16 Dec 2008 21:10:30 +0000 (22:10 +0100)]
MIPS: qemu_mips: move env storage just after u-boot
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Wolfgang Denk [Tue, 16 Dec 2008 22:48:27 +0000 (23:48 +0100)]
Prepare 2009.01-rc1
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Tue, 16 Dec 2008 22:13:46 +0000 (23:13 +0100)]
include/configs/at91cap9adk.h: fix typo.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Tue, 16 Dec 2008 21:32:25 +0000 (22:32 +0100)]
board/trab/memory.c: Fix compile problems.
Apply changes from commit
44b4dbed to board/trab/memory.c, too.
Actually we'd need a major cleanup here - as it turns out,
board/trab/memory.c is more or less a verbatim copy of
post/drivers/memory.c ... but then, trab is EOL anyway,r
so this is not worth the effort.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Scott Wood [Tue, 16 Dec 2008 20:24:16 +0000 (14:24 -0600)]
NAND: Mark the BBT as scanned prior to calling scan_bbt.
Otherwise, recursion can occur if scan_bbt does not find a bad block
table, and tries to write one, and the attempt to erase the BBT area
causes a bad block check.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Wolfgang Denk [Tue, 16 Dec 2008 16:16:34 +0000 (17:16 +0100)]
Merge branch 'master' of ssh://gemini/home/wd/git/u-boot/master
Ilya Yanok [Thu, 11 Dec 2008 02:51:57 +0000 (05:51 +0300)]
jffs2: include <linux/mtd/compat.h> instead of defining own min_t
Include <linux/mtd/compat.h> header for min_t definition instead of
providing our own one. Removes warnings in case of OneNAND support
enabled.
Although I thinks it's a bit silly to include <linux/mtd/compat.h>
just for min_t...
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Stefan Roese <sr@denx.de>
Becky Bruce [Thu, 4 Dec 2008 05:04:37 +0000 (23:04 -0600)]
powerpc: fix io.h build warning with CONFIG_PHYS_64BIT
Casting a pointer to a phys_addr_t when it's an unsigned long long
on a 32-bit system without first casting to a non-pointer type
generates a compiler warning. Fix this.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Wolfgang Denk [Tue, 16 Dec 2008 15:22:50 +0000 (16:22 +0100)]
trab: make trab_fkt standalone code independent of libgcc
Use our own local functions in lib_arm/ instead.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Tue, 16 Dec 2008 13:44:06 +0000 (14:44 +0100)]
post/Makefile: fix dependency problem with parallel builds
Parallel builds (using "make -jN") would occasionally fail with error
messages like
ppc_4xxFP-objdump: string.o: File format not recognized
or
post/libpost.a(cpu.o): In function `cpu_post_test':
/home/wd/git/u-boot/work/post/lib_ppc/cpu.c:130: undefined reference to `cpu_post_test_string'
or similar. We now make sure to run the 'postdeps" step before
attempting to build the specific POST libraries.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Tue, 16 Dec 2008 13:41:02 +0000 (14:41 +0100)]
Makefile: fix dependency problem with parallel builds
Parallel builds (using "make -jN") would occasionally fail with error
messages like
include/autoconf.mk:212: *** missing separator. Stop.
Line numbers and affected boards were changing. Obviously some
Makefiles included autoconf.mk while it was still being written to.
As a fix, we now write to a temporary file first and then rename it,
so that it is really ready to use as soon as it appears.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Tue, 16 Dec 2008 00:02:17 +0000 (01:02 +0100)]
Coding style cleanup, update CHANGELOG.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Mike Frysinger [Thu, 11 Dec 2008 23:39:08 +0000 (18:39 -0500)]
spi/stmicro: fix debug() display of cmd
The stmicro_wait_ready() func tries to show the actual opcode that was sent
to the device, but instead it displays the array pointer. Fix it to pull
out the opcode from the start of the array.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Thu, 11 Dec 2008 11:23:37 +0000 (06:23 -0500)]
env_sf: support embedded environments
If both CONFIG_ENV_SECT_SIZE and CONFIG_ENV_SIZE are defined, and the sect
size is larger than the env size, then it means the env is embedded in a
block. So we have to save/restore the part of the sector which is not the
environment. Previously, saving the environment in SPI flash in this
setup would probably brick the board as the rest of the sector tends to
contain actual U-Boot data/code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Timur Tabi [Wed, 3 Dec 2008 17:28:30 +0000 (11:28 -0600)]
i2c: merge all i2c_reg_read() and i2c_reg_write() into inline functions
All implementations of the functions i2c_reg_read() and
i2c_reg_write() are identical. We can save space and simplify the
code by converting these functions into inlines and putting them in
i2c.h.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-By: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Dave Liu [Fri, 5 Dec 2008 07:36:14 +0000 (15:36 +0800)]
lib_ppc: rework the flush_cache
- It is possible to miss flush/invalidate the last
cache line, we fix it at here.
- add the volatile and memory clobber.
They are pointed by Scott Wood.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Kumar Gala [Sat, 13 Dec 2008 23:20:28 +0000 (17:20 -0600)]
Introduce addr_map library
Add a library that helps in translating between virtual and physical
addresses. This library can be useful as a simple means to implement
map_physmem() and virt_to_phys() for platforms that need functionality
beyond the simple 1:1 mapping.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Sat, 13 Dec 2008 23:20:27 +0000 (17:20 -0600)]
Introduce virt_to_phys()
virt_to_phys() returns the physical address given a virtual. In most
cases this will be just the input value as the vast majority of
systems run in a 1:1 mode.
However in systems that are not running this way it should report the
physical address or ~0 if no mapping exists for the given virtual
address.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Yuri Tikhonov [Sun, 7 Dec 2008 21:12:50 +0000 (22:12 +0100)]
POST Make: fix the sub-dir dependencies missing.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Martin Michlmayr [Wed, 6 Aug 2008 11:44:05 +0000 (14:44 +0300)]
Fix a typo in fw_env.config
Reported-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Peter Tyser [Mon, 1 Dec 2008 22:22:45 +0000 (16:22 -0600)]
Remove unused CONFIG_ADDR_STREAMING defines
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser [Mon, 24 Nov 2008 17:54:47 +0000 (11:54 -0600)]
cmd_mem: Remove unused variable
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Jean-Christophe PLAGNIOL-VILLARD [Sun, 14 Dec 2008 09:29:39 +0000 (10:29 +0100)]
Fix new found CFG_
Also fix some minor typos.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Sergei Poselenov [Fri, 19 Sep 2008 10:07:34 +0000 (12:07 +0200)]
Remove compiler warning: target CPU does not support interworking
This warning is issued by modern ARM-EABI GCC on non-thumb targets.
Signed-off-by: Vladimir Panfilov <pvr@emcraft.com>
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Jean-Christophe PLAGNIOL-VILLARD [Mon, 24 Nov 2008 12:33:51 +0000 (13:33 +0100)]
Fix FIT and FDT support to have CONFIG_OF_LIBFDT and CONFIG_FIT independent
FDT support is used for both FIT style images and for architectures
that can pass a fdt blob to an OS (ppc, m68k, sparc).
For other architectures and boards which do not pass a fdt blob to an
OS but want to use the new uImage format, we just need FIT support.
Now we can have the 4 following configurations :
1) FIT only CONFIG_FIT
2) fdt blob only CONFIG_OF_LIBFDT
3) both CONFIG_OF_LIBFDT & CONFIG_FIT
4) none none
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Wolfgang Denk [Fri, 12 Dec 2008 23:36:25 +0000 (00:36 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx
Wolfgang Denk [Fri, 12 Dec 2008 23:34:12 +0000 (00:34 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-mips
Wolfgang Denk [Fri, 12 Dec 2008 23:26:19 +0000 (00:26 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-sh
Wolfgang Denk [Fri, 12 Dec 2008 23:25:24 +0000 (00:25 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-microblaze
Wolfgang Denk [Fri, 12 Dec 2008 23:20:01 +0000 (00:20 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-ubi
Matthias Fuchs [Wed, 10 Dec 2008 14:13:32 +0000 (15:13 +0100)]
ppc4xx: Disable EEPROM write access on PMC440 boards
This patch disables EEPROM wrtie access by default on PMC440 board.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Matthias Fuchs [Wed, 10 Dec 2008 14:12:56 +0000 (15:12 +0100)]
ppc4xx: Fix Ethernet PHY LED configuration on PMC440 boards
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Stefan Roese [Tue, 18 Nov 2008 15:36:12 +0000 (16:36 +0100)]
MIPS: Flush data cache upon relocation
This patch now adds a flush to the data cache upon relocation. The
current implementation is missing this. Only a comment states that it
should be done. So let's really do it now.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Stefan Roese [Tue, 18 Nov 2008 15:36:22 +0000 (16:36 +0100)]
MIPS: Add CONFIG_SKIP_LOWLEVEL_INIT
This patch adds the CONFIG_SKIP_LOWLEVEL_INIT option to start.S. This
enables support for boards where the lowlevel initialization is
already done when U-Boot runs (e.g. via OnChip ROM).
This will be used in the upcoming VCTH board support.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Stefan Roese [Wed, 12 Nov 2008 12:18:02 +0000 (13:18 +0100)]
MIPS: Add board_early_init_f() to init_sequence
This patch adds the board_early_init_f() call to the MIPS init
sequence. A weak dummy implementation is also added which can be
overridden by a board specific version.
This will be used by the upcoming VCTH board support.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Stefan Roese [Wed, 12 Nov 2008 12:18:19 +0000 (13:18 +0100)]
MIPS: Add onenand_init() to board.c and move nand_init()
This patch adds a call to onenand_init() for OneNAND support and moves
the nand_init() call to an earlier place, so that the environment can
be used from NAND and OneNAND.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Nobuhiro Iwamatsu [Tue, 9 Dec 2008 02:32:46 +0000 (11:32 +0900)]
sh: Update sh2/sh2a timer
Renesas SH2/SH2A timer broken.
This patch fix timer function.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Jean-Christophe PLAGNIOL-VILLARD [Fri, 5 Dec 2008 06:27:37 +0000 (07:27 +0100)]
sh: r2dplus fix register access
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Jean-Christophe PLAGNIOL-VILLARD [Tue, 2 Dec 2008 06:40:03 +0000 (07:40 +0100)]
sh: r2dplus/lowlevel_init: coding style fix
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Tue, 25 Nov 2008 02:05:19 +0000 (11:05 +0900)]
sh: Changed value of CACHE_OC_NUM_ENTRIES and CACHE_OC_WAY_SHIFT
SH4 is different a value of CACHE_OC_NUM_ENTRIES and
CACHE_OC_WAY_SHIFT every CPU.
This patch corrects these values.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Thu, 20 Nov 2008 07:44:42 +0000 (16:44 +0900)]
sh: Update sh timer function
Change to write/readX function and fix timer problem.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Tue, 4 Nov 2008 02:58:58 +0000 (11:58 +0900)]
sh: Migo-R: Update BSC value
A value of BSC CS4 was wrong, Fixed it.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Mon, 17 Nov 2008 07:52:09 +0000 (16:52 +0900)]
sh: Update ms7722se board config
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Mon, 17 Nov 2008 07:53:09 +0000 (16:53 +0900)]
sh: Update SuperH serial driver
The address of SCFSR register is wrong at SH7720/SH7721.
This patch fix this.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Jean-Christophe PLAGNIOL-VILLARD [Tue, 11 Nov 2008 21:20:15 +0000 (22:20 +0100)]
sh: fix rsk7203 and MigoR out of tree build
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Matthias Fuchs [Wed, 10 Dec 2008 13:41:25 +0000 (14:41 +0100)]
ppc4xx: Update TEXT_BASE for CPCI405 boards
This patch fixes building U-Boot for CPCI405 boards.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Tue, 9 Dec 2008 19:08:01 +0000 (20:08 +0100)]
ppc4xx: Remove some features from ALPR to fit into 256k again
Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Wed, 10 Dec 2008 09:32:59 +0000 (10:32 +0100)]
UBI: Set ubi_dev.type back to DEV_TYPE_NONE upon failing initialization
With this patch we set the type back to NONE upon failing UBI partition
initialization. Otherwise further calls to the UBI subsystem would try
to really access the non-existing UBI partition.
Thanks to Michael Lawnick for pointing this out.
Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Wed, 10 Dec 2008 09:28:33 +0000 (10:28 +0100)]
UBI: Return -ENOMEM upon failing malloc
Return with correct error code (-ENOMEM) from ubi_attach_mtd_dev() upon
failing malloc().
Signed-off-by: Stefan Roese <sr@denx.de>
Ben Warren [Wed, 10 Dec 2008 07:34:15 +0000 (23:34 -0800)]
Fix compile error in building MBX860T.
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Michal Simek [Tue, 25 Nov 2008 10:42:20 +0000 (11:42 +0100)]
microblaze: Remove XUPV2P board
---
Microblaze platforms use generic settings and to have
many platforms is confusing that's why I decided to remove this
platform from U-BOOT. ml401 tree is sufficient for covering
all Microblaze platforms.
This change will go through microblaze custodian tree.