Cindy H Kao [Wed, 19 Aug 2009 02:27:18 +0000 (19:27 -0700)]
wimax/i2400m: don't write to memory allocated by request_firmware()
In kernel 2.6.31, the firmware requested to ram could be marked
with read only attribute, and we can't write any thing directly
to the memory when setting up the last JUMP brh cmd.
Changed so that the scratch buffer is used.
Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Inaky Perez-Gonzalez [Tue, 1 Sep 2009 00:15:49 +0000 (17:15 -0700)]
wimax/i2400m: be smarter about copying command buffer to bm_cmd_buf
Because some underlying bus APIs (like USB) don't like data buffers in
the stack or vmalloced areas, the i2400m driver provides a scratch
buffer (i2400m->bm_cmd_buf) for said low-level drivers to copy command
data to before passing it to said API. This is only used during boot
mode.
However, at some the code was copying the buffer even when the command
was already specified in said buffer. This is ok, but it needs to be
more careful. As thus, change so that:
(a) the copy happens only if command buffer is not the scratch buffer
(b) use memmove() in case there is overlapping
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Cindy H Kao [Tue, 11 Aug 2009 01:36:15 +0000 (18:36 -0700)]
wimax/i2400m/sdio: clear the INTR status bit after reading size
In order to avoid issues during high-load traffic, the interrupt
status register has to be cleared ONLY after the RX size is read.
Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Dirk Brandewie [Wed, 12 Aug 2009 18:29:46 +0000 (11:29 -0700)]
wimax/i2400m: USB driver uses a configurable endpoint map
Newer generations of the i2400m USB WiMAX device use a different
endpoint map; in order to make it easy to support it, we make the
endpoint-to-function mapeable instead of static.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Cindy H Kao [Tue, 18 Aug 2009 02:39:12 +0000 (19:39 -0700)]
wimax/iwmc3200: increase wait time before enable retry
When trying to enable the iwmc3200 WiMAX SDIO function, we loop
waiting for the top controller to be up and running (at which point we
can succesfully enable the function). Between each try we wait for
I2400MS_INIT_SLEEP_INTERVAL ms.
Integration tests have found the current value of 10ms to be too
short; it was upped to 100ms to give more time to the top controller
to be ready.
Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Cindy H Kao [Tue, 18 Aug 2009 02:39:12 +0000 (19:39 -0700)]
wimax/iwmc3200: don't disable the SDIO function if enable fails
In the iwmc3200, disabling the WiMAX SDIO function when enable fails
would possibly result in a device reset triggered by the iwmc3200's
top controller since it monitors the bus reset activities from each
SDIO function. In any case, the disable makes no sense; if the enable
fails, it should not be disabled.
Thus we remove the unecessary sdio_disable_func() in
i2400ms_enable_function().
Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Cindy H Kao [Tue, 18 Aug 2009 02:17:58 +0000 (19:17 -0700)]
wimax/iwmc3200: overwrite SDIO IOR timeout value to avoid platform hang
The default SDIO IOE wait timeout returned from iwmc3200-wimax's CCCR
is not efficient. This inefficiency will actually cause problems on
Moorestown platforms (system hang).
This is a sillicon bug that requires a software patch to by
overwritting func->enable_timeout. The new value I2400MS_IOR_TIMEOUT
is recommended and verified from the system integration results.
Future sillicon releases will have this default value corrected in the
future.
Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Dirk Brandewie [Thu, 13 Aug 2009 20:48:29 +0000 (13:48 -0700)]
wimax/i2400m: Make boot retries a BUS-specific parameter
In i2400m-based devices, the driver's bootloader will retry to load
the firmware when things go wrong. The driver currently has a constant
(I2400M_BOOT_RETRIES) which governs the max number of tries.
However, different SKUs of the same hardware may admit or require
different numbers of retries due to it's particulars, so it is made a
BUS specific parameter and different values are assigned for 5x50
devices versus the 3200 ones.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Dirk Brandewie [Tue, 18 Aug 2009 15:51:52 +0000 (08:51 -0700)]
wimax/i2400m: Ensure boot mode cmd and ack buffers are alloc'd before first message
The change to the SDIO boot mode RX chain could try to use the cmd and
ack buffers befor they were allocated. USB does not have the problem
but both were changed for consistency's sake.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Dirk Brandewie [Fri, 24 Jul 2009 16:04:33 +0000 (09:04 -0700)]
wimax/i2400m: Update comments to talk about SDIO reset and not USB.
Fixing comments from original cut and paste error
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Dan Williams [Thu, 17 Sep 2009 20:06:14 +0000 (13:06 -0700)]
i2400m: minimal ethtool support
Add minimal ethtool support for carrier detection.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Roel Kluin [Sun, 12 Jul 2009 22:59:53 +0000 (00:59 +0200)]
wimax: misplaced parenthesis
Fix misplaced parenthesis
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Roel Kluin [Sun, 12 Jul 2009 23:48:42 +0000 (01:48 +0200)]
i2400m: keep index within ms_to_errno[]
Ensure that index `status' remains within ms_to_errno[]
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Inaky Perez-Gonzalez [Fri, 28 Aug 2009 00:54:53 +0000 (17:54 -0700)]
wimax: indicate initial SW rfkill state is "blocked"
The WiMAX stack assumes that all WiMAX devices are SW OFF when they
are initialized. The recent changes in the RFKILL stack thus cause an
initial call after rfkill_register(), because by default, rfkill
considers devices to be SW ON upon registration.
So call rfkill_init_sw_state() to set it to SW OFF so
rfkill_register() doesn't do that unnecessary step.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Cindy H Kao [Thu, 27 Aug 2009 22:25:12 +0000 (15:25 -0700)]
wimax/i2400m: fix the bootmode RX deadlock in SDIO driver
i2400ms_bus_bm_wait_for_ack() causes a race condition. It happens
because this function clears i2400ms->bm_ack_size before waiting for
an interrupt, which is set by the interrupt service routine i2400ms_rx()
to indicate reception and size of received data; thus, if the interrupt
came right before the clearing/waiting, it is lost.
The fix is clear the bm_ack_size to -EINPROGRESS before we are enabling
the RX interrupt configuration in i2400ms_rx_setup(). Then everytime
when the interrupt service routine i2400ms_rx() is invoked during bootmode,
bm_ack_size is updated with the actual rx_size and it is cleared to
-EINPROGRESS again after the RX data is handled.
Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Oliver Neukum [Wed, 19 Aug 2009 19:50:45 +0000 (13:50 -0600)]
wimax/i2400m/usb: remove unnecessary power management primitive in i2400m
This patch removes an unneeded power management primitive.
Power management is automatically enabled as probe ends.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Steffen Klassert [Wed, 7 Oct 2009 22:50:40 +0000 (22:50 +0000)]
xfrm: remove skb_icv_walk
The last users of skb_icv_walk are converted to ahash now,
so skb_icv_walk is unused and can be removed.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert [Wed, 7 Oct 2009 22:49:57 +0000 (22:49 +0000)]
ah: Remove obsolete code
ah4 and ah6 are converted to ahash now, so we can remove the
code for the obsolete hash algorithm.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert [Wed, 7 Oct 2009 22:49:01 +0000 (22:49 +0000)]
ah6: convert to ahash
This patch converts ah6 to the new ahash interface.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert [Wed, 7 Oct 2009 22:48:17 +0000 (22:48 +0000)]
ah4: convert to ahash
This patch converts ah4 to the new ahash interface.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert [Wed, 7 Oct 2009 22:47:16 +0000 (22:47 +0000)]
ah: Add struct crypto_ahash to ah_data
To support for ahash algorithms, we add a pointer to a
crypto_ahash to ah_data.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alan Cox [Wed, 14 Oct 2009 05:22:24 +0000 (05:22 +0000)]
cosa: Kill off the use of the old ioctl path
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 15 Oct 2009 00:12:40 +0000 (00:12 +0000)]
net: sk_drops consolidation part 2
- skb_kill_datagram() can increment sk->sk_drops itself, not callers.
- UDP on IPV4 & IPV6 dropped frames (because of bad checksum or policy checks) increment sk_drops
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 15 Oct 2009 06:30:45 +0000 (06:30 +0000)]
inet: rename some inet_sock fields
In order to have better cache layouts of struct sock (separate zones
for rx/tx paths), we need this preliminary patch.
Goal is to transfert fields used at lookup time in the first
read-mostly cache line (inside struct sock_common) and move sk_refcnt
to a separate cache line (only written by rx path)
This patch adds inet_ prefix to daddr, rcv_saddr, dport, num, saddr,
sport and id fields. This allows a future patch to define these
fields as macros, like sk_refcnt, without name clashes.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Krishna Kumar [Wed, 14 Oct 2009 19:55:07 +0000 (19:55 +0000)]
genetlink: Optimize and one bug fix in genl_generate_id()
1. GENL_MIN_ID is a valid id -> no need to start at
GENL_MIN_ID + 1.
2. Avoid going through the ids two times: If we start at
GENL_MIN_ID+1 (*or bigger*) and all ids are over!, the
code iterates through the list twice (*or lesser*).
3. Simplify code - no need to start at idx=0 which gets
reset to GENL_MIN_ID.
Patch on net-next-2.6. Reboot test shows that first id
passed to genl_register_family was 16, next two were
GENL_ID_GENERATE and genl_generate_id returned 17 & 18
(user level testing of same code shows expected values
across entire range of MIN/MAX).
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Krishna Kumar [Wed, 14 Oct 2009 19:54:53 +0000 (19:54 +0000)]
genetlink: Optimize genl_register_family()
genl_register_family() doesn't need to call genl_family_find_byid
when GENL_ID_GENERATE is passed during register.
Patch on net-next-2.6, compile and reboot testing only.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Krishna Kumar [Wed, 14 Oct 2009 19:54:19 +0000 (19:54 +0000)]
cxgb3: No need to wake queue in xmit handler
The xmit handler doesn't need to wake the queue after stopping
it temporarily (some other drivers are doing the same).
Patch on net-next-2.6, multiple netperf sessions tested.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Einar Lueck [Wed, 14 Oct 2009 22:54:59 +0000 (22:54 +0000)]
ctcm rollback in case of errors
Group device now cleanly reacts to failures during channel start and
implements a clean rollback.
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Klaus-Dieter Wacker [Wed, 14 Oct 2009 22:54:58 +0000 (22:54 +0000)]
lcs: Recognize return codes of ccw_device_set_online().
The creation of a new lcs device requires a call to the function
ccw_device_set_online() for the read and the write channel. Failure
of either call should terminate the lcs device creation immediately
with return code -ENODEV.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Klaus-Dieter Wacker [Wed, 14 Oct 2009 22:54:57 +0000 (22:54 +0000)]
lcs: ODEBUG: object is on stack, but not annotated.
Timer_list structure in lcs_send_lancmd() is allocated on stack.
Initialization with init_timer() leads to above ODEBUG message.
Instead use init_timer_on_stack() which prevents above msg.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Wed, 14 Oct 2009 22:54:56 +0000 (22:54 +0000)]
af_iucv: remove duplicate sock_set_flag
Remove duplicate sock_set_flag(sk, SOCK_ZAPPED) in iucv_sock_close,
which has been overlooked in September-commit
7514bab04e567c9408fe0facbde4277f09d5eb74.
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hendrik Brueckner [Wed, 14 Oct 2009 22:54:55 +0000 (22:54 +0000)]
af_iucv: use sk functions to modify sk->sk_ack_backlog
Instead of modifying sk->sk_ack_backlog directly, use respective
socket functions.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dhananjay Phadke [Fri, 16 Oct 2009 15:50:12 +0000 (15:50 +0000)]
netxen; update version to 4.0.62
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Narender Kumar [Fri, 16 Oct 2009 15:50:11 +0000 (15:50 +0000)]
netxen: sysfs control for auto firmware recovery
Firmware hang detection and recovery (reset) need to
be disabled for diagnostic tools, which can run
some disruptive tests.
This adds a driver level control to turn off this
feature by diag tools.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dhananjay Phadke [Fri, 16 Oct 2009 15:50:10 +0000 (15:50 +0000)]
netxen: fix error codes in for tools access
Use -EIO or -EINVAL as error codes, these can get passed up
to applications (tools).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Kumar Salecha [Fri, 16 Oct 2009 15:50:09 +0000 (15:50 +0000)]
netxen: onchip memory access change
Add support for different windowing scheme for on chip
memory in future chip revisions. This is required by
diagnostic tools.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Kumar Salecha [Fri, 16 Oct 2009 15:50:08 +0000 (15:50 +0000)]
netxen: reset sequence changes
Future revisions need different chip reset sequence
and firmware initialization.
Also clean up some never used debug code.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Kumar Salecha [Fri, 16 Oct 2009 15:50:07 +0000 (15:50 +0000)]
netxen: 128 memory controller support
Future revisions of the chip have 128 bit memory
transactions. Require drivers to implement rmw
in case of sub-128 bit accesses by driver. This
is mostly used by diagnostic tools.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Kumar Salecha [Fri, 16 Oct 2009 15:50:06 +0000 (15:50 +0000)]
netxen: defines for next revision
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ajit Khaparde [Sat, 17 Oct 2009 01:02:12 +0000 (18:02 -0700)]
be2net: Add support for next generation of BladeEngine device.
Add new PCI ids to support next generation of BladeEngine device.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rémi Denis-Courmont [Thu, 15 Oct 2009 19:29:14 +0000 (12:29 -0700)]
Phonet: hold socket before giving it to sk_deliver_skb()
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Thu, 15 Oct 2009 07:19:31 +0000 (00:19 -0700)]
bnx2x: Update to version 1.52.1-1
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Thu, 15 Oct 2009 07:19:05 +0000 (00:19 -0700)]
bnx2x: Report the maximal available BW as link speed
The device is limited to the maximal BW allocation, so it should be displayed as
the link speed to notify the user.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Thu, 15 Oct 2009 07:18:47 +0000 (00:18 -0700)]
bnx2x: Do not call load/unload functionality from DCC
There is really no need to clear the MAC or the FW filtering rules - it was
added for completion, but caused race conditions with load/unload. Removing this
redundant code
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Thu, 15 Oct 2009 07:18:27 +0000 (00:18 -0700)]
bnx2x: Adding FW mailbox mutex
DCC commands are not protected with the RTNL lock, so a mutex should be added
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Thu, 15 Oct 2009 07:18:08 +0000 (00:18 -0700)]
bnx2x: Changing the Disabled state to a flag
When working with DCC, a function can be disabled or enabled (virtual link down
or up). Using the function state introduced some race conditions with the
load/unload flow.
Using a separate flag to indicate that the function is disabled.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Thu, 15 Oct 2009 07:17:45 +0000 (00:17 -0700)]
bnx2x: Remove old FW files
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Thu, 15 Oct 2009 07:17:20 +0000 (00:17 -0700)]
bnx2x: Allowing 0 as initial fairness value
Value of zero was used to disable the fairness mechanism. Though the code
(driver and FW) allowed changing the value at run time, it did not allow to do
that if the mechanism was disabled to begin with.
Fixed the FW to allow turning on and off the mechanism at run time. Fixed the
code to read the value from the chip at the right sequence.
Without this fix, if the initial value was set to zero, traffic could not run on
the interface.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein [Thu, 15 Oct 2009 07:16:27 +0000 (00:16 -0700)]
bnx2x: Add FW 5.2.7
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 15 Oct 2009 04:32:43 +0000 (21:32 -0700)]
sparc: Add missing __NR_recvmmsg define.
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 15 Oct 2009 03:40:11 +0000 (20:40 -0700)]
net: sk_drops consolidation
sock_queue_rcv_skb() can update sk_drops itself, removing need for
callers to take care of it. This is more consistent since
sock_queue_rcv_skb() also reads sk_drops when queueing a skb.
This adds sk_drops managment to many protocols that not cared yet.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Sailer [Wed, 14 Oct 2009 22:15:24 +0000 (15:15 -0700)]
hamradio: Fix bit test correctly.
Signed-off-by: Thomas Sailer <t.sailer@alumni.ethz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rémi Denis-Courmont [Wed, 14 Oct 2009 00:48:31 +0000 (00:48 +0000)]
Phonet: forward incoming packets
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rémi Denis-Courmont [Wed, 14 Oct 2009 00:48:30 +0000 (00:48 +0000)]
Phonet: route outgoing packets
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rémi Denis-Courmont [Wed, 14 Oct 2009 00:48:29 +0000 (00:48 +0000)]
Phonet: routing table Netlink interface
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rémi Denis-Courmont [Wed, 14 Oct 2009 00:48:28 +0000 (00:48 +0000)]
Phonet: routing table backend
The Phonet "universe" only has 64 addresses, so we keep a trivial flat
routing table.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rémi Denis-Courmont [Wed, 14 Oct 2009 00:48:27 +0000 (00:48 +0000)]
Phonet: deliver broadcast packets to broadcast sockets
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnaldo Carvalho de Melo [Wed, 14 Oct 2009 20:11:30 +0000 (13:11 -0700)]
ia64: Fix up the syscall table for recvmmsg
Reported-by: "Tony Luck" <tony.luck@intel.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Gleixner [Wed, 14 Oct 2009 08:19:46 +0000 (01:19 -0700)]
net: Remove BKL from tun
The lock_kernel/unlock_kernel() in cycle_kernel_lock() which is called
in tun_chr_open() is not serializing against anything and safe to
remove.
tun_chr_fasync() is serialized by get/put_tun() and fasync_helper()
has no dependency on BKL. The modification of tun->flags is racy with
and without the BKL so removing it does not make it worse.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 13 Oct 2009 19:55:20 +0000 (12:55 -0700)]
Merge branch 'master' of /linux/kernel/git/davem/net-2.6
Sriram [Wed, 7 Oct 2009 02:44:30 +0000 (02:44 +0000)]
TI DaVinci EMAC: Clear statistics register properly.
The mechanism to clear the statistics register is dependent
on the status of GMIIEN bit in MAC control register. If the
GMIIEN bit is set, the stats registers are write to decrement.
If the GMIIEN bit is cleared, the stats registers are plain
read/write registers. The stats register clearing operation
must take into account the current state of GMIIEN as it
can be cleared when the interface is brought down.
With existing implementation logic, querying for interface stats
when the interface is down, can corrupt the statistics counters.
This patch examines the GMIIEN bit status in MAC_CONTROL
register before choosing an appropriate mask for clearing stats
registers.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Acked-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
françois romieu [Wed, 7 Oct 2009 12:44:20 +0000 (12:44 +0000)]
r8169: partial support and phy init for the 8168d
Extracted from Realtek's 8.012.00 r8168 driver.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Simon Farnsworth <simon.farnsworth@onelan.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
Manuel Lauss [Tue, 13 Oct 2009 07:25:49 +0000 (07:25 +0000)]
net: smsc911x: allow platform_data to specify mac address
Extend the driver to accept a MAC address specified in platform_data.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Manuel Lauss [Tue, 13 Oct 2009 07:25:48 +0000 (07:25 +0000)]
net: enable smsc911x on MIPS
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ajit Khaparde [Tue, 13 Oct 2009 01:46:56 +0000 (01:46 +0000)]
ixgb: Fix erroneous display of stats by ethtool -S
Commit
5675f221 overlooked the way offsets for netdev stats were considered.
Because of this some of the stats shown by ethtool -S were wrong.
This patch fixes it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ajit Khaparde [Tue, 13 Oct 2009 01:46:29 +0000 (01:46 +0000)]
igb: Fix erroneous display of stats by ethtool -S
Commit
337e067d overlooked the way offsets for netdev stats were considered.
Because of this some of the stats shown by ethtool -S were wrong.
This patch fixes it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ajit Khaparde [Tue, 13 Oct 2009 01:45:48 +0000 (01:45 +0000)]
e1000: Fix erroneous display of stats by ethtool -S
Commit
23d26497 overlooked the way offsets for netdev stats were considered.
Because of this some of the stats shown by ethtool -S were wrong.
This patch fixes it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ajit Khaparde [Tue, 13 Oct 2009 01:45:09 +0000 (01:45 +0000)]
e1000e: Fix erroneous display of stats by ethtool -S
Commit
fd8235bb overlooked the way offsets for netdev stats were considered.
Because of this some of the stats shown by ethtool -S were wrong.
This patch fixes it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ajit Khaparde [Tue, 13 Oct 2009 01:47:33 +0000 (01:47 +0000)]
ixgbe: Fix erroneous display of stats by ethtool -S
Commit
59aa3cc4 overlooked the way offsets for netdev stats were considered.
Because of this some of the stats shown by ethtool -S were wrong.
This patch fixes it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dhananjay Phadke [Tue, 13 Oct 2009 05:31:45 +0000 (05:31 +0000)]
netxen: add sysfs entries for diag tools
Add sysfs entries to enable register and memory access
for diagnostic tools.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dhananjay Phadke [Tue, 13 Oct 2009 05:31:44 +0000 (05:31 +0000)]
netxen: separate register and memory access lock
Since register and onboard memory access has separate
window registers, they need not be kept under same lock.
Also, memory is always accessed from process context
(mostly for firmware init and diagnostic tools).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dhananjay Phadke [Tue, 13 Oct 2009 05:31:43 +0000 (05:31 +0000)]
netxen: annotate register windowing code
Use common variables crb_win, ocm_win for all revisions of chip.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dhananjay Phadke [Tue, 13 Oct 2009 05:31:42 +0000 (05:31 +0000)]
netxen: add access to on chip memory for tools
Add access to on chip memory, this is used by
debug and diagnostic tools only.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Kumar Salecha [Tue, 13 Oct 2009 05:31:41 +0000 (05:31 +0000)]
netxen: remove sub 64-bit mem accesses
Sub 64-bit / unaligned access to oncard memory was only used
by old diagnostic tools, causes some intermittent issues when
memory controller agent is used. The new access method was
added by commit
ea6828b8aa3a8ebae8d7740f32f212ba1d2f0742
("netxen: improve pci memory access"). Firmware init anyway
uses 8-byte strides.
This also fixes address/offset calculation for NX2031 context
memory (SIU). For NX3031, SIU uses same register offsets
as packet memory (MIU).
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 13 Oct 2009 05:34:20 +0000 (05:34 +0000)]
net: Use netdev_alloc_skb_ip_align()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 13 Oct 2009 18:41:34 +0000 (11:41 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6
roel kluin [Tue, 6 Oct 2009 10:07:15 +0000 (10:07 +0000)]
sb1250-mac: duplicate setting of bit V_MAC_RX_PL_THRSH(4) in sbmac_channel_start()
The bit V_MAC_RX_PL_THRSH(4) was already set a few lines higher.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
roel kluin [Tue, 6 Oct 2009 01:20:08 +0000 (01:20 +0000)]
net/hamradio: fix test in receive()
The negation makes it a bool before the comparison and hence it
will never evaluate to true.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
roel kluin [Wed, 7 Oct 2009 00:59:42 +0000 (00:59 +0000)]
x25: bit and/or confusion in x25_ioctl()?
Looking at commit
ebc3f64b864f it appears that this was intended
and not the original, equivalent to `if (facilities.reverse & ~0x81)'.
In x25_parse_facilities() that patch changed how facilities->reverse
was set. No other bits were set than 0x80 and/or 0x01.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Karen Xie [Thu, 8 Oct 2009 09:11:05 +0000 (09:11 +0000)]
cxgb3: Added private MAC address and provisioning packet handler for iSCSI
This patch added support of private MAC address per port and provisioning
packet handler for iSCSI traffic only.
The above changes are isolated to the cxgb3 driver, independent of any scsi or iscsi driver changes.
Acked-by: Karen Xie <kxie@chelsio.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Rakesh Ranjan <rakesh@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Magnus Damm [Fri, 9 Oct 2009 00:20:04 +0000 (00:20 +0000)]
net: add Runtime PM to the sh_eth driver
Add Runtime PM support to the sh_eth driver.
The clock to the ethernet hardware block will be
enabled as long as the network device is up.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Magnus Damm [Fri, 9 Oct 2009 00:17:14 +0000 (00:17 +0000)]
net: allow sh_eth to get mac address through platform data
Extend the sh_eth driver to allow passing the mac address
using the platform data structure. This to simplify board
setup code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wolfgang Grandegger [Thu, 8 Oct 2009 22:17:11 +0000 (22:17 +0000)]
can: make the number of echo skb's configurable
This patch allows the CAN controller driver to define the number of echo
skb's used for the local loopback (echo), as suggested by Kurt Van
Dijck, with the function:
struct net_device *alloc_candev(int sizeof_priv,
unsigned int echo_skb_max);
The CAN drivers have been adapted accordingly. For the ems_usb driver,
as suggested by Sebastian Haas, the number of echo skb's has been
increased to 10, which improves the transmission performance a lot.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 7 Oct 2009 17:11:23 +0000 (17:11 +0000)]
net: Add netdev_alloc_skb_ip_align() helper
Instead of hardcoding NET_IP_ALIGN stuff in various network drivers,
we can add a helper around netdev_alloc_skb()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 9 Oct 2009 00:16:19 +0000 (00:16 +0000)]
tcp: replace ehash_size by ehash_mask
Storing the mask (size - 1) instead of the size allows fast path to be
a bit faster.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmin Ratiu [Fri, 9 Oct 2009 03:11:14 +0000 (03:11 +0000)]
ipv6: fix devconf after adding force_tllao option
Signed-off-by: Cosmin Ratiu <cratiu@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Artamonow [Tue, 13 Oct 2009 10:17:37 +0000 (03:17 -0700)]
irda/sa1100_ir: check return value of startup hook
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 9 Oct 2009 04:43:40 +0000 (04:43 +0000)]
udp: Fix udp_poll() and ioctl()
udp_poll() can in some circumstances drop frames with incorrect checksums.
Problem is we now have to lock the socket while dropping frames, or risk
sk_forward corruption.
This bug is present since commit
95766fff6b9a78d1
([UDP]: Add memory accounting.)
While we are at it, we can correct ioctl(SIOCINQ) to also drop bad frames.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Krzysztof Halasa [Fri, 9 Oct 2009 06:16:10 +0000 (06:16 +0000)]
WAN: fix Cisco HDLC handshaking.
Cisco HDLC uses keepalive packets and sequence numbers to determine link
state. In rare cases both ends could transmit keepalive packets at the same
time, causing the received sequence numbers to be treated as incorrect.
Now we accept our current sequence number as well as the previous one.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Willy Tarreau [Tue, 13 Oct 2009 07:27:40 +0000 (00:27 -0700)]
tcp: fix tcp_defer_accept to consider the timeout
I was trying to use TCP_DEFER_ACCEPT and noticed that if the
client does not talk, the connection is never accepted and
remains in SYN_RECV state until the retransmits expire, where
it finally is deleted. This is bad when some firewall such as
netfilter sits between the client and the server because the
firewall sees the connection in ESTABLISHED state while the
server will finally silently drop it without sending an RST.
This behaviour contradicts the man page which says it should
wait only for some time :
TCP_DEFER_ACCEPT (since Linux 2.4)
Allows a listener to be awakened only when data arrives
on the socket. Takes an integer value (seconds), this
can bound the maximum number of attempts TCP will
make to complete the connection. This option should not
be used in code intended to be portable.
Also, looking at ipv4/tcp.c, a retransmit counter is correctly
computed :
case TCP_DEFER_ACCEPT:
icsk->icsk_accept_queue.rskq_defer_accept = 0;
if (val > 0) {
/* Translate value in seconds to number of
* retransmits */
while (icsk->icsk_accept_queue.rskq_defer_accept < 32 &&
val > ((TCP_TIMEOUT_INIT / HZ) <<
icsk->icsk_accept_queue.rskq_defer_accept))
icsk->icsk_accept_queue.rskq_defer_accept++;
icsk->icsk_accept_queue.rskq_defer_accept++;
}
break;
==> rskq_defer_accept is used as a counter of retransmits.
But in tcp_minisocks.c, this counter is only checked. And in
fact, I have found no location which updates it. So I think
that what was intended was to decrease it in tcp_minisocks
whenever it is checked, which the trivial patch below does.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas de Pesloüan [Tue, 13 Oct 2009 07:45:06 +0000 (00:45 -0700)]
bonding: change bond_create_proc_entry() to return void
The function bond_create_proc_entry is currently of type int.
Two versions of this function exist:
The one in the ifdef CONFIG_PROC_FS branch always return 0.
The one in the else branch (which is empty) return nothing.
When CONFIG_PROC_FS is undef, this cause the following warning:
drivers/net/bonding/bond_main.c: In function `bond_create_proc_entry':
drivers/net/bonding/bond_main.c:3393: warning: control reaches end of
non-void function
No caller of this function use the returned value.
So change the returned type from int to void and remove the
useless return 0; .
Signed-off-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Reported-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ken Kawasaki [Tue, 13 Oct 2009 07:32:55 +0000 (00:32 -0700)]
3c574_cs: spin_lock the set_multicast_list function
3c574_cs:
spin_lock the set_multicast_list function.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Rankin [Tue, 13 Oct 2009 07:32:02 +0000 (00:32 -0700)]
net: Teach pegasus driver to ignore bluetoother adapters with clashing Vendor:Product IDs
The Belkin F8T012xx1 bluetooth adaptor has the same vendor and product
IDs as the Belkin F5D5050, so we need to teach the pegasus driver to
ignore adaptors belonging to the "Wireless" class 0xE0. For this one
case anyway, seeing as pegasus is a driver for "Wired" adaptors.
Signed-off-by: Chris Rankin <rankincj@yahoo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dhananjay Phadke [Tue, 13 Oct 2009 07:26:04 +0000 (00:26 -0700)]
netxen: fix pci bar mapping
Use resource_size_t for PCI resource remapping instead
of unsigned long. Physical addresses can exceed range of
long data type (e.g with PAE).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alan Cox [Mon, 12 Oct 2009 05:27:55 +0000 (05:27 +0000)]
ethoc: fix warning from 32bit build
drivers/net/ethoc.c: In function ‘ethoc_open’:
drivers/net/ethoc.c:667: warning: comparison of distinct pointer types
lacks a cast
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alan Cox [Mon, 12 Oct 2009 05:27:48 +0000 (05:27 +0000)]
libertas: fix build
drivers/net/wireless/libertas/cmdresp.c: In function ‘lbs_process_event’:
drivers/net/wireless/libertas/cmdresp.c:519: error: ‘TASK_INTERRUPTIBLE’
undeclared (first use in this function)
drivers/net/wireless/libertas/cmdresp.c:519: error: (Each undeclared
identifier is reported only once
drivers/net/wireless/libertas/cmdresp.c:519: error: for each function it
appears in.)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shreyas Bhatewara [Tue, 13 Oct 2009 07:15:51 +0000 (00:15 -0700)]
net: VMware virtual Ethernet NIC driver: vmxnet3
Ethernet NIC driver for VMware's vmxnet3
From: Shreyas Bhatewara <sbhatewara@vmware.com>
This patch adds driver support for VMware's virtual Ethernet NIC: vmxnet3
Guests running on VMware hypervisors supporting vmxnet3 device will thus have
access to improved network functionalities and performance.
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: Ronghua Zhang <ronghua@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vincent Sanders [Tue, 13 Oct 2009 07:03:11 +0000 (00:03 -0700)]
net: Fix IXP 2000 network driver building.
The IXP 2000 network driver was failing to build as it has its own
statistics gathering which was not compatible with the recent network
device operations changes. This patch fixes the driver in the obvious
way and has been compile tested. I have been unable to get the ixp2000
maintainer to comment or test this fix.
Signed-off-by: Vincent Sanders <vince@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Mon, 12 Oct 2009 09:27:07 +0000 (09:27 +0000)]
sfc: 10Xpress: Initialise pause advertising flags
The mdio module now handles reconfiguration of pause advertising
through ethtool, but not initialisation. Add the necessary
initialisation to tenxpress_phy_init().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Mon, 12 Oct 2009 09:26:37 +0000 (09:26 +0000)]
mdio: Expose pause frame advertising flags to ethtool
In mdio45_ethtool_gset_npage() and mdio45_ethtool_gset(), check MDIO
pause frame advertising flags and set the corresponding ethtool flags.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / kernel / kernel-generic.git / log