Marek Vasut [Fri, 17 May 2019 18:32:18 +0000 (20:32 +0200)]
ARM: imx: novena: Enable DM USB
Enable DM USB support on iMX6Q Novena.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
Marek Vasut [Fri, 17 May 2019 18:32:17 +0000 (20:32 +0200)]
ARM: imx: novena: Convert block devices to DM
Enable DM block, DM MMC and DM SATA support on iMX6Q Novena
convert board code to match the DM support.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
Marek Vasut [Fri, 17 May 2019 18:32:16 +0000 (20:32 +0200)]
ARM: imx: novena: Enable DM GPIO
Enable DM GPIO support on iMX6Q Novena and fix up board code
where applicable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
Marek Vasut [Fri, 17 May 2019 18:32:15 +0000 (20:32 +0200)]
ARM: imx: novena: Enable DM pin control
Enable DM pin control support on iMX6Q Novena.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
Marek Vasut [Fri, 17 May 2019 18:32:14 +0000 (20:32 +0200)]
ARM: dts: imx: novena: Import Novena DT from Linux
Import iMX6Q Novena device tree from Linux 5.1-rc7
37624b58542f .
Enable DT control in full U-Boot .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
Jun Nie [Wed, 8 May 2019 06:38:36 +0000 (14:38 +0800)]
pico-imx7d: enable boot without PMIC
If PMIC is not probed successfully, it is still OK to boot
with default configuration although power is not optimized.
Default voltage of SW1A/SW1B is 1.1V/1.0V for PC32PF3000A1EP
on pico according to table 42 of spec of PF3000 ver 9.0.
Default mode of SW1A/SW1B is APS as expected(table 47).
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Jun Nie [Wed, 8 May 2019 06:38:35 +0000 (14:38 +0800)]
pico-imx7d: README: Add BL33 usage case
Add Documentation of BL33 usage case. U-boot is in
non-secure world in this case.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Jun Nie [Wed, 8 May 2019 06:38:34 +0000 (14:38 +0800)]
pico-imx7d: Add bl33 config
Add default configuration to run u-boot as BL33 in the boot flow case
of ATF(ARM Trusted Firmware) -> OPTEE -> U-boot.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Jun Nie [Wed, 8 May 2019 06:38:33 +0000 (14:38 +0800)]
pico-imx7d: Add boot option for verified boot
Add boot option to boot from fitimage to support verified boot.
The boot script plain text file should be packed into fit blob as
image with name of bootscr.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Jun Nie [Wed, 8 May 2019 06:38:32 +0000 (14:38 +0800)]
pico-imx7d: Reserve region of memory to OPTEE
Subtracts CONFIG_OPTEE_TZDRAM_SIZE from the available DRAM size so that
the OPTEE memory is not override during u-boot relocation.
Note the OPTEE live in the end part of DRAM and OPTEE boot process will
itself subtract the DRAM region it lives in from the memory map passed
to Linux.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Jun Nie [Wed, 8 May 2019 06:38:31 +0000 (14:38 +0800)]
pico-imx7d: Correct uart clock root
Correct uart clock root ID. Incorrect ID may result the
clock is gated because rate value 0 is returned in
imx_get_uartclk()
The ID can be ignored if CONFIG_SKIP_LOWLEVEL_INIT is not enabled
because init_clk_uart() will enable all uart clocks in that case.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Jun Nie [Wed, 8 May 2019 06:38:30 +0000 (14:38 +0800)]
imx: mx7: Skip secure init in arch_cpu_init
Skip secure related initialization in arch_cpu_init if low level
init is skipped. Because these should be done in early stage
firmware, such as ARM trusted firmware.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Jun Nie [Wed, 8 May 2019 06:38:29 +0000 (14:38 +0800)]
mx7_common: Share configs to skip low level init
Share configs in mx7 to skip low level init if we are in the case where
OPTEE is loaded already (maybe by ARM Trusted Firmware) and that most of
the low level initialization is already done and that we may/should skip
it doing them here.
Fix the definition detection with size detection to decide whether to skip
it.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Heiko Schocher [Sun, 26 May 2019 10:15:47 +0000 (12:15 +0200)]
spi: imx: work with cs greater 0
currently spi mxc driver can only handle cs 0.
Allow it to handle also cs > 0.
Signed-off-by: Heiko Schocher <hs@denx.de>
Heiko Schocher [Sun, 26 May 2019 10:15:46 +0000 (12:15 +0200)]
spi: imx: remove doubled pointer from mxc_spi_probe
in mxc_spi_probe() plat and mxcs pointer are created:
struct mxc_spi_slave *plat = bus->platdata;
struct mxc_spi_slave *mxcs = dev_get_platdata(bus);
which have the same value. Remove plat pointer.
Signed-off-by: Heiko Schocher <hs@denx.de>
Heiko Schocher [Tue, 28 May 2019 11:44:31 +0000 (13:44 +0200)]
arm, imx, Makefile: fix u-boot-dtb.imx build in CONFIG_MULTI_DTB_FIT case
in case CONFIG_MULTI_DTB_FIT is set and u-boot-dtb.imx
image is build, currently u-boot-dtb.bin is used for
generating the u-boot-dtb.imx binary, which is wrong, as
it contains only a dtb blob not the fit.blob
Use instead the u-boot-fit-dtb.bin for generating
u-boot-dtb.imx which contains the fit.blob.
Signed-off-by: Heiko Schocher <hs@denx.de>
Ezequiel Garcia [Sat, 25 May 2019 22:19:41 +0000 (19:19 -0300)]
wandboard: Rework Makefile to prevent spl.o from being built
The spl.c source was entirely conditioned by CONFIG_SPL_BUILD.
Change this moving CONFIG_SPL_BUILD to be used in the Makefile,
which is slightly cleaner and more readable.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Marek Vasut [Fri, 17 May 2019 14:58:54 +0000 (16:58 +0200)]
ARM: imx: dh-imx6: Convert SPI support to DM
Enable DM SPI and SF support on DHCOM iMX6 PDK2.
Convert board code to match the DM support.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Fri, 17 May 2019 14:58:53 +0000 (16:58 +0200)]
ARM: imx: dh-imx6: Convert USB support to DM
Enable DM USB host support on DHCOM iMX6 PDK2.
Convert board code to match the DM support.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Fri, 17 May 2019 14:58:52 +0000 (16:58 +0200)]
ARM: imx: dh-imx6: Convert SATA support to DM
Enable DM SATA support on DHCOM iMX6 PDK2.
Convert board code to match the DM support.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Fri, 17 May 2019 14:58:51 +0000 (16:58 +0200)]
ARM: imx: dh-imx6: Convert SD/MMC support to DM
Enable DM block and DM MMC support on DHCOM iMX6 PDK2.
Convert board code to match the DM support.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Fri, 17 May 2019 14:58:50 +0000 (16:58 +0200)]
ARM: imx: dh-imx6: Enable DM GPIO
Enable DM GPIO support on DHCOM iMX6 PDK2 and fix up board code
where applicable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Fri, 17 May 2019 14:58:49 +0000 (16:58 +0200)]
ARM: imx: dh-imx6: Enable DM pin control
Enable DM pin control support on DHCOM iMX6 PDK2.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Fri, 17 May 2019 14:58:48 +0000 (16:58 +0200)]
ARM: dts: imx: dh-imx6: Fix SPI CS polarity on DHCOM iMX6 PDK2
The SPI nCS signal is active low, make it so.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Fri, 17 May 2019 14:58:47 +0000 (16:58 +0200)]
ARM: dts: imx: dh-imx6: Import DHCOM iMX6 PDK2 DTs from Linux
Import DHCOM iMX6 PDK2 device tree from Linux 5.1.1
b724e9356404 .
Enable DT control in full U-Boot .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Breno Matheus Lima [Tue, 4 Jun 2019 02:54:44 +0000 (02:54 +0000)]
Revert "drivers/crypto/fsl: assign job-rings to non-TrustZone"
Commit
22191ac35344 ("drivers/crypto/fsl: assign job-rings to
non-TrustZone") breaks HABv4 encrypted boot support in the
following i.MX devices:
- i.MX6UL
- i.MX7S
- i.MX7D
- i.MX7ULP
For preparing a HABv4 encrypted boot image it's necessary to
encapsulate the generated DEK in a blob. In devices listed
above the blob generation function takes into consideration
the Job Ring TrustZone ownership configuration (JROWN_NS)
and can be only decapsulated by the same configuration.
The ROM code expects DEK blobs encapsulated by the Secure World
environments which commonly have JROWN_NS = 0.
As U-Boot is running in Secure World we must have JROWN_NS = 0
so the blobs generated by dek_blob tool can be decapsulated
by the ROM code.
Job-rings assignment is now handled in OP-TEE OS, this commit can
be safely reverted.
https://github.com/OP-TEE/optee_os/pull/2986
This reverts commit
22191ac353445ad8fafc5a78aefcd94e78963041.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Lukasz Majewski [Wed, 8 May 2019 14:26:23 +0000 (16:26 +0200)]
config: Update KP's imx53 HSC config to pass key pressed information
The information about pressed key is relevant in performing correct
update and recovery scenarios via USB pendrive.
This commit modifies envs to provide it.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Wed, 8 May 2019 14:26:22 +0000 (16:26 +0200)]
config: Update KP's imx53 HSC config to support SWUpdate
This commit updates envs responsible for using USB pendrive as a
SWUpdate based tool for recovery and update.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Fabio Estevam [Fri, 3 May 2019 17:05:04 +0000 (14:05 -0300)]
imx: Use a convenient default value for SYS_MALLOC_F_LEN
Commit
3a7c45f6a772 ("simple-bus: add DM_FLAG_PRE_RELOC flag to
simple-bus driver") causes some i.MX boards that were converted
to DM, such as warp7, to fail to boot.
As explained by Lukas Auer:
"With the patch, U-Boot probes the drivers for devices under simple-bus
device tree nodes in the pre-relocation device model. The default value
of CONFIG_SYS_MALLOC_F_LEN (0x400) leaves U-Boot with not enough memory to
do this, causing it to hang."
Fix this problem by providing a convenient default value for
CONFIG_SYS_MALLOC_F_LEN.
Reported-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Suggested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Heiko Schocher <hs@denx.de>
Sébastien Szymanski [Tue, 14 May 2019 11:46:20 +0000 (13:46 +0200)]
opos6uldev: don't call enable_lcdif_clock
The mxsfb driver already calls enable_lcdif_clock.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Sébastien Szymanski [Tue, 14 May 2019 11:33:46 +0000 (13:33 +0200)]
opos6ul: set REFSEL and REFR fields
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Breno Matheus Lima [Fri, 26 Apr 2019 02:56:48 +0000 (02:56 +0000)]
imx: hab: Increase CSF_SIZE for i.MX6 and i.MX7 devices
In certain i.MX devices the encrypted boot image is failing to boot.
According to AN12056 "Encrypted Boot on HABv4 and CAAM Enabled Devices"
it's necessary to pad CSF to 0x2000 and append DEK blob.
In this case the total image size in boot data structure must cover the
entire binary otherwise the dek_blob won't be copied to memory and image
won't be decrypted.
Increase CSF_SIZE to 0x4000 to avoid such issue when booting encrypted
boot images.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Marcel Ziswiler [Fri, 26 Apr 2019 18:48:14 +0000 (20:48 +0200)]
colibri-imx6ull: fix usb host mode
This fixes an issue with USB host mode.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Marek Vasut [Sun, 12 May 2019 20:43:25 +0000 (22:43 +0200)]
ARM: imx: apalis_imx6: Drop ad-hoc SATA binding
Drop the ad-hoc AHCI binding code, this is superseded by
CONFIG_DWC_AHSATA_AHCI=y resp. drivers/ata/dwc_ahsata.c
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Stefan Agner <stefan.agner@toradex.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Matti Vaittinen [Tue, 7 May 2019 07:43:39 +0000 (10:43 +0300)]
regulator:
bd71837: copy the
bd71837 pmic driver from NXP imx u-boot
https://source.codeaurora.org/external/imx/uboot-imx
cherry picked, styled and merged commits:
- MLK-18387 pmic: Add pmic driver for
BD71837:
e9a3bec2e95a
- MLK-18590 pmic:
bd71837: Change to use new fdt API:
acdc5c297a96
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Igor Opaniuk [Fri, 10 May 2019 09:35:29 +0000 (12:35 +0300)]
colibri_imx7: migrate usb to driver model
Migrate USB to Driver Model (CONFIG_DM_USB=y).
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Jagan Teki [Fri, 26 Apr 2019 09:01:46 +0000 (14:31 +0530)]
configs: imx6-engicam: Update the recoveryboot setting
Since recovery boot on mmc can get the mmcpart and mmcroot
dynamically, drop the static definitions and handle it
properly.
Tested-by: Shyam Saini <shyam.saini@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Igor Opaniuk [Fri, 17 May 2019 14:48:43 +0000 (17:48 +0300)]
toradex apalis/colibri: extend CONFIG_SYS_MALLOC_F_LEN
Extend size of the malloc() pool for use before relocation, from 0x400
(default one) to 0x2000 (CONFIG_SYS_MALLOC_F_LEN=0x2000),
as adding of DM_FLAG_PRE_RELOC flag to simple-bus driver introduced a
regression on multiple boards, because of more intensive usage of malloc()
pool and therefore a broken boot as the size of pool isn't sufficient.
Fixes: 3a7c45f6a7 ("simple-bus: add DM_FLAG_PRE_RELOC flag to simple-bus")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Marcel Ziswiler [Tue, 9 Apr 2019 15:21:48 +0000 (17:21 +0200)]
apalis_imx6: add device tree to makefile
Add device tree to Makefile to avoid newly introduced error:
Device Tree Source is not correctly specified.
Please define 'CONFIG_DEFAULT_DEVICE_TREE'
or build with 'DEVICE_TREE=<device_tree>' argument
make[1]: *** [dts/Makefile:28: arch/arm/dts/imx6-apalis.dtb] Error 1
make: *** [Makefile:1009: dts/dt.dtb] Error 2
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Igor Opaniuk [Thu, 23 May 2019 11:05:50 +0000 (11:05 +0000)]
apalis/colibri imx6: provide proper fdtfile value
Provide proper fdtfile env variable value before invoking distro_bootcmd
command.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Parthiban Nallathambi [Sun, 7 Apr 2019 18:32:42 +0000 (20:32 +0200)]
ARM: dts: i.MX6ULL: U-Boot specific dts for u-boot, dm-spl
u-boot,dm-spl property is specific to U-Boot, so created one
for i.MX6ULL platforms.
Signed-off-by: Parthiban Nallathambi <parthitce@gmail.com>
Trent Piepho [Thu, 4 Apr 2019 21:52:04 +0000 (21:52 +0000)]
power: pfuze100: Fix off by one error in voltage table handling
The code that sets a regulator by looking up the voltage in a table had
an off by one error. vsel_mask is a bitmask, not the number of table
entries, so a vsel_mask value of 0x7 indicates there are 8, not 7,
entries in the table.
Cc: Peng Fan <Peng.Fan@freescale.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Ye Li [Thu, 16 May 2019 03:18:51 +0000 (03:18 +0000)]
mx7ulp: Add common plugin codes for mx7ulp
Add common plugin codes to call ROM's hwcnfg_setup and generate IVT2
header.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Marcel Ziswiler [Fri, 31 May 2019 15:56:39 +0000 (18:56 +0300)]
board: toradex: add colibri imx8qxp 2gb wb it v1.0b module support
This commit adds initial support for the Toradex Colibri iMX8QXP 2GB WB
IT V1.0B module. Unlike the V1.0A early access samples exclusively
booting from SD card, they are now strapped to boot from eFuses which
are factory fused to properly boot from their on-module eMMC. U-Boot
supports either booting from the on-module eMMC or may be used for
recovery purpose using the universal update utility (uuu) aka mfgtools
3.0.
Functionality wise the following is known to be working:
- eMMC and MMC/SD card
- Ethernet
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QXP as of
yet.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Marcel Ziswiler [Fri, 31 May 2019 15:56:38 +0000 (18:56 +0300)]
imx: fix building for i.mx8 without spl
Building with Travis CI complained and stopped with the following error:
+cc1: fatal error: opening output file spl/u-boot-spl.cfgout: No such
file or directory
+compilation terminated.
This fixes commit
caceb739ea07 ("imx: build flash.bin for i.MX8") which
took SPL being enabled on i.MX8 for granted.
Reported-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Adam Ford [Wed, 13 Mar 2019 15:49:22 +0000 (10:49 -0500)]
ARM: imx6logic: Stop overwriting fdt_file if manually set
The board file uses the processor type to determine what dtb file
is set. Unfortunately, if the user wants to manually set this,
it get gets overwritten upon boot. This patch adds a check to
see if the value is already set and only changes it if the value
is empty.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tom Rini [Sat, 8 Jun 2019 00:39:32 +0000 (20:39 -0400)]
spl: Correct SPL_SIZE_LIMIT Kconfig option
When introduced this limit was an int but was then changed to hex
without noting as much in the prompt nor changing existing users. Put
this back to an int.
Reported-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
Fixes: 2577015dc5c4 ("spl: add overall SPL size check")
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Fri, 7 Jun 2019 22:03:18 +0000 (18:03 -0400)]
Merge branch '2019-06-07-master-imports'
- Include Heinrich's series to move the i.MX board size check function
to be more widely available.
- Include Simon Goldschmidt's patch to make it possible to have a more
accurate SPL size check applied.
Simon Goldschmidt [Fri, 24 May 2019 20:07:04 +0000 (22:07 +0200)]
spl: add overall SPL size check
This adds a size check for SPL that can dynamically check generated
SPL binaries (including devicetree) for a size limit that ensures
this image plus global data, heap and stack fit in initial SRAM.
Since some of these sizes are not available to make, a new host tool
'spl_size_limit' is added that dumps the resulting maximum size for
an SPL binary to stdout. This tool is used in toplevel Makefile to
implement the size check on SPL binaries.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Heinrich Schuchardt [Tue, 2 Apr 2019 17:19:07 +0000 (19:19 +0200)]
configs: rk3288: Tinker Board SPL file must fit into 32 KiB
The SPL image for the Tinker Board has to fit into 32 KiB. This includes
up to 2 KiB for the file header.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Tue, 2 Apr 2019 17:19:06 +0000 (19:19 +0200)]
configs: define CONFIG_SPL_SIZE_LIMIT
A new configuration variable CONFIG_SPL_SIZE_LIMIT is introduced to define
the board specific maximum size for the SPL file.
Use Makefile function size_check() to implement the test.
Depending on the size of CONFIG_SPL_SIZE_LIMIT an error like the following
is thrown:
spl/u-boot-spl.bin exceeds file size limit:
limit: 30720 bytes
actual: 33426 bytes
excess: 2706 bytes
make: *** [Makefile:1663: spl/u-boot-spl.bin] Error 1
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Tue, 2 Apr 2019 17:19:05 +0000 (19:19 +0200)]
imx: move BOARD_SIZE_CHECK to main Makefile
We currently have duplicate definitions for BOARD_SIZE_CHECK in Makefile
and arch/arm/mach-imx/Makefile.
Move the board size check from arch/arm/mach-imx/Makefile to Makefile.
Depending on the value of CONFIG_BOARD_SIZE_LIMIT an error like an error
like the following is thrown:
u-boot-dtb.imx exceeds file size limit:
limit: 503696 bytes
actual: 509720 bytes
excess: 6024 bytes
make: *** [Makefile:1051: u-boot-dtb.imx] Error 1
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Heinrich Schuchardt [Tue, 2 Apr 2019 17:19:04 +0000 (19:19 +0200)]
Makefile: reusable function for BOARD_SIZE_CHECK
Carve out function size_check from macro BOARD_SIZE_CHECK. This will allow
us to reuse the function for other file size checks.
Depending on the value of CONFIG_BOARD_SIZE_LIMIT an error like the
following is thrown:
u-boot-dtb.img exceeds file size limit:
limit: 409516 bytes
actual: 444346 bytes
excess: 34830 bytes
make: *** [Makefile:1212: u-boot-dtb.img] Error 1
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Mon, 29 Apr 2019 06:08:43 +0000 (08:08 +0200)]
lib/vsprintf: allow printing upper case GUIDs
In the UEFI context GUIDs are expected to be rendered in upper case.
The patch uses the formerly unused bit 1 of the parameter str_format
of function uuid_bin_to_str() to indicate if we need upper or lower case
output.
Function uuid_string() in vsprint.c is adjusted to correctly set the bit
depending on the print format code.
%pUb:
01020304-0506-0708-090a-
0b0c0d0e0f10
%pUB:
01020304-0506-0708-090A-
0B0C0D0E0F10
%pUl:
04030201-0605-0807-090a-
0b0c0d0e0f10
%pUL:
04030201-0605-0807-090A-
0B0C0D0E0F10
Up to this point only a diagnostic message in mount_ubifs() using '%pUB' is
concerned by the change. Further patches are needed to adjust the UEFI
subsystem.
A unit test is provided inside the ut_print command.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Rini [Wed, 5 Jun 2019 19:53:18 +0000 (15:53 -0400)]
Merge tag 'efi-2019-07-rc4-2' of git://git.denx.de/u-boot-efi
Pull request for UEFI sub-system for v2019.07-rc4-2
Support for managing the non-volatile attribute of UEFI variables
is added though we do not have a backend for persistence yet.
Error messages for changes of UEFI variables are provided.
UEFI boottime service implementations are corrected.
Tom Rini [Wed, 5 Jun 2019 19:49:09 +0000 (15:49 -0400)]
Merge branch '2019-06-05-master-imports'
- More DaVinci fixes
- BuR platform fix
Heiko Schocher [Mon, 27 May 2019 06:14:16 +0000 (08:14 +0200)]
cmd/led: check subcommand "list" instead "l"
current implementation for checking if "led list"
command is called checks only if "l" is passed to the
led command. This prevents switching leds with name
which starts also with a "l". So check for passing
"list".
While at it, also fix a typo in led command usage.
Signed-off-by: Heiko Schocher <hs@denx.de>
Jean-Jacques Hiblot [Thu, 23 May 2019 12:07:23 +0000 (14:07 +0200)]
board: am335x/mux: configure the pins for 8-bit data transfer on MMC1
This is required for proper operation of the 8-bit data transfers.
This fixes transient errors seen on BeagleBone Black.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Holger Brunck [Tue, 4 Jun 2019 12:10:32 +0000 (14:10 +0200)]
board/km: update maintainer e-mail
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Bartosz Golaszewski [Wed, 29 May 2019 08:02:00 +0000 (10:02 +0200)]
arm: davinci: remove leftover assembly
There are no more users of lowlevel_init.S. Remove the file.
Suggested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
David Lechner [Wed, 29 May 2019 08:01:59 +0000 (10:01 +0200)]
configs/legoev3: define CONFIG_SKIP_LOWLEVEL_INIT
This adds a define for CONFIG_SKIP_LOWLEVEL_INIT in the legoev3 config.
On the EV3, U-Boot is loaded into RAM by another bootloader, so we
don't need the lowlevel init in U-Boot.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Adam Ford [Wed, 29 May 2019 14:36:58 +0000 (09:36 -0500)]
ARM: da850evm: Fix reading MAC from SPI
The MAC address is located at at the last 64K of SPI Flash, and
it's 6 bytes long. This patch corrects both the length and
starting byte of the MAC address.
Signed-off-by: Adam Ford <aford173@gmail.com>
Adam Ford [Wed, 29 May 2019 20:42:53 +0000 (15:42 -0500)]
arm: omap3: Manually initialize GPIO if OF_CONTROL doesn't
The commong initialization code manually initializes the GPIO
even when OF_CONTROL does it, so we can reduce the code size a
bit by not doing it manually when we have device tree support.
Using the omap3_logic board (dm3730), the sizes shrunk:
Before:
text data bss dec hex filename
561066 28596 116880 706542 ac7ee u-boot
55245 1605 1888 58738 e572 spl/u-boot-spl
After
text data bss dec hex filename
560898 28548 116872 706318 ac70e u-boot
55121 1557 1888 58566 e4c6 spl/u-boot-spl
Signed-off-by: Adam Ford <aford173@gmail.com>
Adam Ford [Fri, 31 May 2019 12:09:22 +0000 (07:09 -0500)]
ARM: DTS: imx6q-logicpd: Resync with Linux 5.1
Resync imx6q-logicpd with Kernel 5.1.5
Signed-off-by: Adam Ford <aford173@gmail.com>
Adam Ford [Thu, 30 May 2019 23:04:44 +0000 (18:04 -0500)]
ARM: davinci: Remove ipam390 linker script from Kconfig
With ipam390 support removed in we can remove the reference to the
linker script since that case will never be true.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Sekhar Nori [Thu, 30 May 2019 13:34:55 +0000 (19:04 +0530)]
ARM: davinci: SPL: fix BSS initialization
U-Boot README recommends initializing SDRAM in board_init_f(). DA850
was doing it as part of board_init_r() (through call to spl_board_init()
which calls arch_cpu_init() which calls da850_ddr_setup())
This worked fine till commit
15b8c7505819 ("davinci:
da850evm/omapl138-lcdk: Move BSS to SDRAM because SRAM is full") moved
BSS to SDRAM.
Functions like mmc_initialize() called in board_init_r() assume BSS is
available. Since SDRAM was not initialized when arch/arm/lib/crt0.S tried
to initialize BSS to 0, BSS is not initialized correctly.
Fix this by simply calling arch_cpu_init() from board_init_f(). Also move
preloader_console_init() there to help debug issues with board_init_r().
With this spl_board_init() is no longer needed, we remove it.
Tested using MMC/SD boot on OMAP-L138 LCDK board.
Tested-by: Adam Ford <aford173@gmail.com> #da850evm
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Tested-by: Peter Howard <phoward@gme.net.au> #omapl138_lcdk
Sekhar Nori [Thu, 30 May 2019 13:34:54 +0000 (19:04 +0530)]
ARM: davinci: omal138_lcdk: fix MMC boot breakage due to driver model conversion
commit
21af33ed0319 ("ARM: davinci: omapl138_lcdk: Enable DM_MMC")
wanted to enable DM_MMC only for U-Boot and not for SPL.
But CONFIG_DM_MMC is defined for SPL build too. Because of this
MMC device was not getting registered for SPL causing MMC/SD
boot breakage.
Instead use CONFIG_IS_ENABLED(DM_MMC) which will remain false until
CONFIG_SPL_DM_MMC is defined.
Tested-by: Adam Ford <aford173@gmail.com> #da850evm
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Tested-by: Peter Howard <phoward@gme.net.au> #omapl138_lcdk
Hannes Schmelzer [Fri, 10 May 2019 09:22:00 +0000 (11:22 +0200)]
board/BuR/common: fix detection for PSC/STM resetcontroller
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Tom Rini [Wed, 5 Jun 2019 14:07:31 +0000 (10:07 -0400)]
Merge git://git.denx.de/u-boot-riscv
- Support Microchip MPFS Icicle board.
- Enable e1000 and nvme support for qemu.
- Enable PCI host ECAM generic driver for qemu.
- Increase the environment size to 128kB for qemu.
Padmarao Begari [Tue, 28 May 2019 10:17:51 +0000 (15:47 +0530)]
riscv: Add Microchip MPFS Icicle board support
This patch adds Microchip MPFS Icicle board support.
For now, NS16550 serial driver is only enabled.
The Microchip MPFS Icicle defconfig by default builds
U-Boot for M-Mode with SMP support.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Bin Meng [Wed, 15 May 2019 15:42:59 +0000 (08:42 -0700)]
riscv: qemu: Enable e1000 and nvme support
Since we have added the PCI support to the 'virt' target, enable
e1000 and NVME as alternate network and storage devices for these
virtio based devices.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Tested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Bin Meng [Wed, 15 May 2019 15:42:58 +0000 (08:42 -0700)]
riscv: qemu: Enable PCI host ECAM generic driver
QEMU 4.0.0 'virt' target integrates a generic ECAM PCI host.
Enable the driver for it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Tested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Karsten Merker [Sun, 5 May 2019 21:36:29 +0000 (23:36 +0200)]
riscv: increase the environment size for the qemu-riscv platform to 128kB
The existing default size of 4kB is too small as the default environment
has already nearly that size and defining a single additional environment
variable can exceed the available space.
Signed-off-by: Karsten Merker <merker@debian.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
AKASHI Takahiro [Tue, 4 Jun 2019 06:52:11 +0000 (15:52 +0900)]
cmd: env: add -nv option for UEFI non-volatile variable
With this option, -nv, at "setenv -e" command, a variable will be defined
as non-volatile.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
AKASHI Takahiro [Tue, 4 Jun 2019 06:52:10 +0000 (15:52 +0900)]
cmd: efidebug: make some boot variables non-volatile
Boot####, BootOrder and BootNext should be non-volatile.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
AKASHI Takahiro [Tue, 4 Jun 2019 06:52:09 +0000 (15:52 +0900)]
efi_loader: bootmgr: make BootNext non-volatile
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
AKASHI Takahiro [Tue, 4 Jun 2019 06:52:06 +0000 (15:52 +0900)]
efi_loader: variable: support non-volatile attribute
The attribute, EFI_VARIABLE_NON_VOLATILE, should be encoded as "nv" flag
in U-Boot variable if specified.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Tue, 4 Jun 2019 18:55:12 +0000 (20:55 +0200)]
efi_loader: notify memory map changes
When the memory map is changed signal events of the
EFI_EVENT_GROUP_MEMORY_MAP_CHANGE event group.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
AKASHI Takahiro [Tue, 28 May 2019 00:00:35 +0000 (09:00 +0900)]
cmd: env: print a message when setting UEFI variable failed
Error message will alert a user that setting/deleting a variable failed.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
AKASHI Takahiro [Wed, 29 May 2019 18:54:25 +0000 (20:54 +0200)]
efi_loader: bootmgr: print a message when loading from BootNext failed
If a user defines BootNext but not BootOrder and loading from BootNext
fails, you will see only a message like this:
BootOrder not defined
This may confuse a user. Adding an error message will be helpful.
An example output looks like this:
=> efidebug boot add 0001 label1 scsi 0:1 "\path1\file1.efi" "--option foo"
=> efidebug boot add 0002 label2 scsi 0:1 "\path2\file2.efi" "--option bar"
=> efidebug boot add 0003 label3 scsi 0:1 "\path3\file3.efi" "--option no"
=> efidebug boot order 0001 0002
=> efidebug boot next 0003
=> bootefi bootmgr
Loading from Boot0003 'label3' failed
Loading from BootNext failed, falling back to BootOrder
Loading from Boot0001 'label1' failed
Loading from Boot0002 'label2' failed
EFI boot manager: Cannot load any image
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Adjust messages.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Sun, 2 Jun 2019 18:02:32 +0000 (20:02 +0200)]
efi_loader: close protocols in UnloadImage()
When UnloadImage() is called all protocols opened by the image have to be
closed.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Sun, 2 Jun 2019 20:54:28 +0000 (22:54 +0200)]
efi_loader: fix EnableCursor()
The EnableCursor() service of the simple text output protocol must update
the the CursorVisible field of the output mode.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Sun, 2 Jun 2019 19:12:17 +0000 (21:12 +0200)]
efi_loader: check timer events in Stall()
During a call to Stall() we should periodically check for timer events.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Sun, 2 Jun 2019 19:02:10 +0000 (21:02 +0200)]
lib: time: export usec_to_tick()
In the UEFI Stall() boottime service we need access to usec_to_tick().
Export the function.
Remove redundant implementation in arch/arm/mach-rockchip/rk_timer.c.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Sat, 1 Jun 2019 23:43:33 +0000 (01:43 +0200)]
efi_loader: DisconnectController() with no driver
If DisconnectController() is called and no driver is managing
ControllerHandle, return EFI_SUCCESS.
UEFI SCT II 2017, 3.3.12 DisconnectController(), 5.1.3.12.4 - 5.1.3.12.6
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Rini [Tue, 4 Jun 2019 12:03:41 +0000 (08:03 -0400)]
Merge git://git.denx.de/u-boot-marvell
- Enable MMC in SPL to enable DM MMC booting on helios4 (Dennis)
Dennis Gilmore [Wed, 29 May 2019 14:36:13 +0000 (09:36 -0500)]
arm: mvebu: helios4: add MMC to SPL DT
This allows SPL to load the main U-Boot image from MMC once DM_MMC is
enabled.
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Tom Rini [Sun, 2 Jun 2019 22:19:45 +0000 (18:19 -0400)]
Merge tag 'efi-2019-07-rc4' of git://git.denx.de/u-boot-efi
Pull request for UEFI sub-system for v2019.07-rc4
Corrections for boottime services for protocols and for the SetTime()
service are provided.
Error messages for the 'setenv -e' and 'bootefi bootmgr' commands are
added.
Tom Rini [Sun, 2 Jun 2019 12:33:10 +0000 (08:33 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-net
- Basic bug fixes and minor features for 2019.07.
Heinrich Schuchardt [Sat, 1 Jun 2019 19:00:50 +0000 (21:00 +0200)]
efi_selftest: unit test for OpenProtocolInformation()
Provide a unit test that checks that the open protocol information is
correctly updated when opening and closing protocols.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Sat, 1 Jun 2019 18:54:32 +0000 (20:54 +0200)]
efi_loader: CloseProtocol() fix open protocol information
CloseProtocol() must delete all open protocol information records relating
to import parameters not only one.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Sat, 1 Jun 2019 18:15:10 +0000 (20:15 +0200)]
efi_loader: open protocol information
When a protocol is opened the open protocol information must be updated.
The key fields of the open protocol information records are ImageHandle,
ControllerHandle, and Attributes.
Consider the Attributes field when determining if an open protocol
information record has to be updated or a new one has to be created.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Sat, 1 Jun 2019 17:29:39 +0000 (19:29 +0200)]
efi_loader: correct HandleProtocol()
The UEFI specification requires that when a protocol is opened via
HandleProtocol() the agent handle is the image handle of the EFI firmware
(see chapter on EFI_BOOT_SERVICES.OpenProtocol()).
Let efi_handle_protocol() pass efi_root as agent handle to
efi_open_protocol().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Vladimir Oltean [Thu, 30 May 2019 00:08:32 +0000 (03:08 +0300)]
cmd: mdio: Fix access to arbitrary PHY addresses
Alex reported the following:
"
I'm doing some MDIO work on a freescale/NXP platform and I bumped into
errors with this command:
=> mdio r emdio#3 5 3
Reading from bus emdio#3
"Synchronous Abort" handler, esr 0x8600000e
elr:
ffffffff862b8000 lr :
000000008200cce4 (reloc)
...
mdio list does not list any PHYs currently because ethernet is using DM
and the interfaces are not probed at this time. The PHY does exist
on the bus though.
The above scenario works with this commit reverted:
e55047ec51a662c12ed53ff543ec7cdf158b2137 cmd: mdio: Switch to generic
helpers when accessing the registers
The current code using generic helpers only works for PHYs that have
been registered and show up in bus->phymap and crashes for arbitrary
IDs. I find it useful to allow reading from other addresses over MDIO
too, certainly helpful for people debugging MDIO on various boards.
"
Fix this by reverting to use the raw MDIO bus operations in case there
is no PHY probed based on DT at the specified address.
This restores the old behavior for these PHYs, which means that the
newly introduced MMD-over-C22 helpers won't be available for them, but
at least they will be accessible again without crashing the system.
Fixes: commit e55047ec51a6 ("cmd: mdio: Switch to generic helpers when accessing the registers")
Reported-by: Alex Marginean <alexm.osslist@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Bin Meng [Wed, 22 May 2019 07:09:47 +0000 (00:09 -0700)]
riscv: sifive: fu540: Enable GEMGXL MGMT driver
Enable the new GEMGXL MGMT driver so that GEM 10/100 Mbps works now.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Tested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Bin Meng [Wed, 22 May 2019 07:09:46 +0000 (00:09 -0700)]
dm: net: macb: Implement link speed change callback
At present the link speed change callback is a nop. According to
macb device tree bindings, an optional "tx_clk" is used to clock
the ethernet controller's TX_CLK under different link speed.
In 10/100 MII mode, transmit logic must be clocked from a free
running clock generated by the external PHY. In gigabit GMII mode,
the controller, not the external PHY, must generate the 125 MHz
transmit clock towards the PHY.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Tested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Bin Meng [Wed, 22 May 2019 07:09:45 +0000 (00:09 -0700)]
dm: net: macb: Update macb_linkspd_cb() signature
This updates DM version macb_linkspd_cb() signature for future
expansion, eg: adding an implementation for link speed changes.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Bin Meng [Wed, 22 May 2019 07:09:44 +0000 (00:09 -0700)]
clk: sifive: Add clock driver for GEMGXL MGMT
This adds a clock driver to support the GEMGXL management IP block
found in FU540 SoCs to control GEM TX clock operation mode for
10/100/1000 Mbps.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Tested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Thierry Reding [Mon, 20 May 2019 15:59:57 +0000 (17:59 +0200)]
net: eth-uclass: Support device tree MAC addresses
Add the standard Ethernet device tree bindings (imported from v5.0 of
the Linux kernel) and implement support for reading the MAC address for
Ethernet devices in the Ethernet uclass. If the "mac-address" property
exists, the MAC address will be parsed from that. If that property does
not exist, the "local-mac-address" property will be tried as fallback.
MAC addresses from device tree take precedence over the ones stored in
a network interface card's ROM.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding [Mon, 20 May 2019 15:59:56 +0000 (17:59 +0200)]
net: eth-uclass: Write MAC address to hardware after probe
In order for the device to use the proper MAC address, which can have
been configured in the environment prior to the device being registered,
ensure that the MAC address is written after the device has been probed.
For devices that are registered before the network stack is initialized,
this is already done during eth_initialize(). If the Ethernet device is
on a bus that is not initialized on early boot, such as PCI, the device
is not available at the time eth_initialize() is called, so we need the
MAC address programming to also happen after probe.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>