Lars-Peter Clausen [Fri, 22 Feb 2013 00:44:04 +0000 (16:44 -0800)]
drivers/video/backlight/adp88?0_bl.c: fix resume
commit
5eb02c01bd1f3ef195989ab05e835e2b0711b5a9 upstream.
Clearing the NSTBY bit in the control register also automatically clears
the BLEN bit. So we need to make sure to set it again during resume,
otherwise the backlight will stay off.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Junxiao Bi [Fri, 22 Feb 2013 00:42:45 +0000 (16:42 -0800)]
ocfs2: unlock super lock if lockres refresh failed
commit
3278bb748d2437eb1464765f36429e5d6aa91c38 upstream.
If lockres refresh failed, the super lock will never be released which
will cause some processes on other cluster nodes hung forever.
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
MITSUNARI Shigeo [Fri, 22 Feb 2013 00:42:01 +0000 (16:42 -0800)]
fs/block_dev.c: page cache wrongly left invalidated after revalidate_disk()
commit
7630b661da330b35dd57b6f5d6d62b386f2dd751 upstream.
We found that bdev->bd_invalidated was left set once revalidate_disk()
is called, which results in page cache flush every time that device is
open.
Specifically, we found this problem in MD block device. Once we resize
a MD device, mdadm --monitor periodically flush all page cache for that
device every 60 or 1000 seconds when it opens the device.
This bug lies since at least 3.2.0 till the latest kernel(3.6.2). Patch
is attached.
The following steps will reproduce the problem.
1. prepair a block device (eg /dev/sdb).
2. create two partitions:
sudo parted /dev/sdb
mklabel gpt
mkpart primary 0% 50%
mkpart primary 50% 100%
3. create a md device.
sudo mdadm -C /dev/md/hoge -l 1 -n 2 -e 1.2 --assume-clean --auto=md --symlink=no /dev/sdb1 /dev/sdb2
4. create file system and mount it
sudo mkfs.ext3 /dev/md/hoge
sudo mkdir /mnt/test
sudo mount /dev/md/hoge /mnt/test
5. try to resize the device
sudo mdadm -G /dev/md/hoge --size=max
6. create a file to fill file cache.
sudo dd if=/dev/urandom of=/mnt/test/data bs=1M count=10
and verify the current status of file by free command.
7. mdadm monitor will open the md device every 1000 seconds and you
will find all file cache on the device are cleared.
The timing can be reduced by the following steps.
a) kill mdadm and restart it with --delay option
/sbin/mdadm --monitor --delay=30 --pid-file /var/run/mdadm/monitor.pid --daemonise --scan --syslog
or open the md device directly.
sudo dd if=/dev/md/hoge of=/dev/null bs=4096 count=1
Signed-off-by: MITSUNARI Shigeo <herumi@nifty.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Jim Somerville [Fri, 22 Feb 2013 00:41:59 +0000 (16:41 -0800)]
inotify: remove broken mask checks causing unmount to be EINVAL
commit
676a0675cf9200ac047fb50825f80867b3bb733b upstream.
Running the command:
inotifywait -e unmount /mnt/disk
immediately aborts with a -EINVAL return code. This is however a valid
parameter. This abort occurs only if unmount is the sole event
parameter. If other event parameters are supplied, then the unmount
event wait will work.
The problem was introduced by commit
44b350fc23e ("inotify: Fix mask
checks"). In that commit, it states:
The mask checks in inotify_update_existing_watch() and
inotify_new_watch() are useless because inotify_arg_to_mask()
sets FS_IN_IGNORED and FS_EVENT_ON_CHILD bits anyway.
But instead of removing the useless checks, it did this:
mask = inotify_arg_to_mask(arg);
- if (unlikely(!mask))
+ if (unlikely(!(mask & IN_ALL_EVENTS)))
return -EINVAL;
The problem is that IN_ALL_EVENTS doesn't include IN_UNMOUNT, and other
parts of the code keep IN_UNMOUNT separate from IN_ALL_EVENTS. So the
check should be:
if (unlikely(!(mask & (IN_ALL_EVENTS | IN_UNMOUNT))))
But inotify_arg_to_mask(arg) always sets the IN_UNMOUNT bit in the mask
anyway, so the check is always going to pass and thus should simply be
removed. Also note that inotify_arg_to_mask completely controls what
mask bits get set from arg, there's no way for invalid bits to get
enabled there.
Lets fix it by simply removing the useless broken checks.
Signed-off-by: Jim Somerville <Jim.Somerville@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: John McCutchan <john@johnmccutchan.com>
Cc: Robert Love <rlove@rlove.org>
Cc: Eric Paris <eparis@parisplace.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tejun Heo [Wed, 20 Feb 2013 23:24:12 +0000 (15:24 -0800)]
posix-timer: Don't call idr_find() with out-of-range ID
commit
e182bb38d7db7494fa5dcd82da17fe0dedf60ecf upstream.
When idr_find() was fed a negative ID, it used to look up the ID
ignoring the sign bit before recent ("idr: remove MAX_IDR_MASK and
move left MAX_IDR_* into idr.c") patch. Now a negative ID triggers
a WARN_ON_ONCE().
__lock_timer() feeds timer_id from userland directly to idr_find()
without sanitizing it which can trigger the above malfunctions. Add a
range check on @timer_id before invoking idr_find() in __lock_timer().
While timer_t is defined as int by all archs at the moment, Andrew
worries that it may be defined as a larger type later on. Make the
test cover larger integers too so that it at least is guaranteed to
not return the wrong timer.
Note that WARN_ON_ONCE() in idr_find() on id < 0 is transitional
precaution while moving away from ignoring MSB. Once it's gone we can
remove the guard as long as timer_t isn't larger than int.
Signed-off-by: Tejun Heo <tj@kernel.org>nnn
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/20130220232412.GL3570@htj.dyndns.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Pawel Moll [Thu, 21 Feb 2013 01:55:50 +0000 (01:55 +0000)]
ALSA: usb: Fix Processing Unit Descriptor parsers
commit
b531f81b0d70ffbe8d70500512483227cc532608 upstream.
Commit
99fc86450c439039d2ef88d06b222fd51a779176 "ALSA: usb-mixer:
parse descriptors with structs" introduced a set of useful parsers
for descriptors. Unfortunately the parses for the Processing Unit
Descriptor came with a very subtle bug...
Functions uac_processing_unit_iProcessing() and
uac_processing_unit_specific() were indexing the baSourceID array
forgetting the fields before the iProcessing and process-specific
descriptors.
The problem was observed with Sound Blaster Extigy mixer,
where nNrModes in Up/Down-mix Processing Unit Descriptor
was accessed at offset 10 of the descriptor (value 0)
instead of offset 15 (value 7). In result the resulting
control had interesting limit values:
Simple mixer control 'Channel Routing Mode Select',0
Capabilities: volume volume-joined penum
Playback channels: Mono
Capture channels: Mono
Limits: 0 - -1
Mono: -1 [100%]
Fixed by starting from the bmControls, which was calculated
correctly, instead of baSourceID.
Now the mentioned control is fine:
Simple mixer control 'Channel Routing Mode Select',0
Capabilities: volume volume-joined penum
Playback channels: Mono
Capture channels: Mono
Limits: 0 - 6
Mono: 0 [0%]
Signed-off-by: Pawel Moll <mail@pawelmoll.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[bwh: Backported to 3.2: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Matt Fleming [Wed, 20 Feb 2013 20:36:12 +0000 (20:36 +0000)]
x86, efi: Make "noefi" really disable EFI runtime serivces
commit
fb834c7acc5e140cf4f9e86da93a66de8c0514da upstream.
commit
1de63d60cd5b ("efi: Clear EFI_RUNTIME_SERVICES rather than
EFI_BOOT by "noefi" boot parameter") attempted to make "noefi" true to
its documentation and disable EFI runtime services to prevent the
bricking bug described in commit
e0094244e41c ("samsung-laptop:
Disable on EFI hardware"). However, it's not possible to clear
EFI_RUNTIME_SERVICES from an early param function because
EFI_RUNTIME_SERVICES is set in efi_init() *after* parse_early_param().
This resulted in "noefi" effectively becoming a no-op and no longer
providing users with a way to disable EFI, which is bad for those
users that have buggy machines.
Reported-by: Walt Nelson Jr <walt0924@gmail.com>
Cc: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1361392572-25657-1-git-send-email-matt@console-pimps.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
[bwh: Backported to 3.2: efi_runtime_init() is not a separate function,
so put a whole set of statements in an if (!disable_runtime) block]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Stefan Bader [Fri, 15 Feb 2013 08:48:52 +0000 (09:48 +0100)]
xen: Send spinlock IPI to all waiters
commit
76eaca031f0af2bb303e405986f637811956a422 upstream.
There is a loophole between Xen's current implementation of
pv-spinlocks and the scheduler. This was triggerable through
a testcase until v3.6 changed the TLB flushing code. The
problem potentially is still there just not observable in the
same way.
What could happen was (is):
1. CPU n tries to schedule task x away and goes into a slow
wait for the runq lock of CPU n-# (must be one with a lower
number).
2. CPU n-#, while processing softirqs, tries to balance domains
and goes into a slow wait for its own runq lock (for updating
some records). Since this is a spin_lock_irqsave in softirq
context, interrupts will be re-enabled for the duration of
the poll_irq hypercall used by Xen.
3. Before the runq lock of CPU n-# is unlocked, CPU n-1 receives
an interrupt (e.g. endio) and when processing the interrupt,
tries to wake up task x. But that is in schedule and still
on_cpu, so try_to_wake_up goes into a tight loop.
4. The runq lock of CPU n-# gets unlocked, but the message only
gets sent to the first waiter, which is CPU n-# and that is
busily stuck.
5. CPU n-# never returns from the nested interruption to take and
release the lock because the scheduler uses a busy wait.
And CPU n never finishes the task migration because the unlock
notification only went to CPU n-#.
To avoid this and since the unlocking code has no real sense of
which waiter is best suited to grab the lock, just send the IPI
to all of them. This causes the waiters to return from the hyper-
call (those not interrupted at least) and do active spinlocking.
BugLink: http://bugs.launchpad.net/bugs/1011792
Acked-by: Jan Beulich <JBeulich@suse.com>
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Wei Liu [Mon, 18 Feb 2013 14:57:58 +0000 (14:57 +0000)]
xen: close evtchn port if binding to irq fails
commit
e7e44e444876478d50630f57b0c31d29f6725020 upstream.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Daniel Vetter [Mon, 21 Jan 2013 18:48:59 +0000 (19:48 +0100)]
intel/iommu: force writebuffer-flush quirk on Gen 4 Chipsets
commit
210561ffd72d00eccf12c0131b8024d5436bae95 upstream.
We already have the quirk entry for the mobile platform, but also
reports on some desktop versions. So be paranoid and set it
everywhere.
References: http://www.mail-archive.com/dri-devel@lists.freedesktop.org/msg33138.html
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "Sankaran, Rajesh" <rajesh.sankaran@intel.com>
Reported-and-tested-by: Mihai Moldovan <ionic@ionic.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Patrik Jakobsson [Wed, 13 Feb 2013 21:20:22 +0000 (22:20 +0100)]
drm/i915: Set i9xx sdvo clock limits according to specifications
commit
4f7dfb6788dd022446847fbbfbe45e13bedb5be2 upstream.
The Intel PRM says the M1 and M2 divisors must be in the range of 10-20 and 5-9.
Since we do all calculations based on them being register values (which are
subtracted by 2) we need to specify them accordingly.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=56359
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Jani Nikula [Thu, 14 Feb 2013 09:23:35 +0000 (11:23 +0200)]
drm/i915: add missing \n to UTS_RELEASE in the error_state
commit
fdfa175d0a9cfa2082ce24e67e284e5acbba452a upstream.
Amending
commit
4518f611ba21ba165ea3714055938a8984a44ff9
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Jan 23 16:16:35 2013 +0100
drm/i915: dump UTS_RELEASE into the error_state
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Mika Kuoppala [Fri, 8 Feb 2013 14:35:37 +0000 (16:35 +0200)]
drm/i915: disable shared panel fitter for pipe
commit
24a1f16de97c4cf0029d9acd04be06db32208726 upstream.
If encoder is switched off by BIOS, but the panel fitter is left on,
we never try to turn off the panel fitter and leave it still attached
to the pipe - which can cause blurry output elsewhere.
Based on work by Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=58867
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Tested-by: Andreas Sturmlechner <andreas.sturmlechner@gmail.com>
[danvet: Remove the redundant HAS_PCH_SPLIT check and add a tiny
comment.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Paulo Zanoni [Fri, 15 Feb 2013 15:36:27 +0000 (13:36 -0200)]
drm: don't add inferred modes for monitors that don't support them
commit
196e077dc165a307efbd9e7569f81bbdbcf18f65 upstream.
If bit 0 of the features byte (0x18) is set to 0, then, according to
the EDID spec, "the display is non-continuous frequency (multi-mode)
and is only specified to accept the video timing formats that are
listed in Base EDID and certain Extension Blocks".
For more information, please see the EDID spec, check the notes of the
table that explains the "Feature Support" byte (18h) and also the
notes on the tables of the section that explains "Display Range Limits
& Additional Timing Description Definition (tag #FDh)".
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=45729
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Jan Beulich [Thu, 20 Dec 2012 10:31:11 +0000 (10:31 +0000)]
xen-blkback: do not leak mode property
commit
9d092603cc306ee6edfe917bf9ab8beb5f32d7bc upstream.
"be->mode" is obtained from xenbus_read(), which does a kmalloc() for
the message body. The short string is never released, so do it along
with freeing "be" itself, and make sure the string isn't kept when
backend_changed() doesn't complete successfully (which made it
desirable to slightly re-structure that function, so that the error
cleanup can be done in one place).
Reported-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
David Henningsson [Tue, 19 Feb 2013 15:11:22 +0000 (16:11 +0100)]
ALSA: hda - hdmi: ELD shouldn't be valid after unplug
commit
bbfd8a19b6913f50a362457c34d49bfafe5e456e upstream.
Currently, eld_valid is never set to false, except at kernel module
load time. This patch makes sure that eld is no longer valid when
the cable is (hot-)unplugged.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Trond Myklebust [Tue, 19 Feb 2013 17:04:42 +0000 (12:04 -0500)]
NLM: Ensure that we resend all pending blocking locks after a reclaim
commit
666b3d803a511fbc9bc5e5ea8ce66010cf03ea13 upstream.
Currently, nlmclnt_lock will break out of the for(;;) loop when
the reclaimer wakes up the blocking lock thread by setting
nlm_lck_denied_grace_period. This causes the lock request to fail
with an ENOLCK error.
The intention was always to ensure that we resend the lock request
after the grace period has expired.
Reported-by: Wangyuan Zhang <Wangyuan.Zhang@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Larry Finger [Sun, 17 Feb 2013 17:01:20 +0000 (17:01 +0000)]
b43: Increase number of RX DMA slots
commit
ccae0e50c16a7f7adb029c169147400d1ce9f703 upstream.
Bastian Bittorf reported that some of the silent freezes on a Linksys WRT54G
were due to overflow of the RX DMA ring buffer, which was created with 64
slots. That finding reminded me that I was seeing similar crashed on a netbook,
which also has a relatively slow processor. After increasing the number of
slots to 128, runs on the netbook that previously failed now worked; however,
I found that 109 slots had been used in one test. For that reason, the number
of slots is being increased to 256.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Bastian Bittorf <bittorf@bluebottle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Steven Rostedt (Red Hat) [Wed, 13 Feb 2013 20:18:38 +0000 (15:18 -0500)]
ftrace: Call ftrace cleanup module notifier after all other notifiers
commit
8c189ea64eea01ca20d102ddb74d6936dd16c579 upstream.
Commit:
c1bf08ac "ftrace: Be first to run code modification on modules"
changed ftrace module notifier's priority to INT_MAX in order to
process the ftrace nops before anything else could touch them
(namely kprobes). This was the correct thing to do.
Unfortunately, the ftrace module notifier also contains the ftrace
clean up code. As opposed to the set up code, this code should be
run *after* all the module notifiers have run in case a module is doing
correct clean-up and unregisters its ftrace hooks. Basically, ftrace
needs to do clean up on module removal, as it needs to know about code
being removed so that it doesn't try to modify that code. But after it
removes the module from its records, if a ftrace user tries to remove
a probe, that removal will fail due as the record of that code segment
no longer exists.
Nothing really bad happens if the probe removal is called after ftrace
did the clean up, but the ftrace removal function will return an error.
Correct code (such as kprobes) will produce a WARN_ON() if it fails
to remove the probe. As people get annoyed by frivolous warnings, it's
best to do the ftrace clean up after everything else.
By splitting the ftrace_module_notifier into two notifiers, one that
does the module load setup that is run at high priority, and the other
that is called for module clean up that is run at low priority, the
problem is solved.
Reported-by: Frank Ch. Eigler <fche@redhat.com>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Nicholas Bellinger [Tue, 19 Feb 2013 02:31:37 +0000 (18:31 -0800)]
target: Add missing mapped_lun bounds checking during make_mappedlun setup
commit
fbbf8555a986ed31e54f006b6cc637ea4ff1425b upstream.
This patch adds missing bounds checking for the configfs provided
mapped_lun value during target_fabric_make_mappedlun() setup ahead
of se_lun_acl initialization.
This addresses a potential OOPs when using a mapped_lun value that
exceeds the hardcoded TRANSPORT_MAX_LUNS_PER_TPG-1 value within
se_node_acl->device_list[].
Reported-by: Jan Engelhardt <jengelh@inai.de>
Cc: Jan Engelhardt <jengelh@inai.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Nicholas Bellinger [Tue, 19 Feb 2013 02:00:33 +0000 (18:00 -0800)]
target: Fix lookup of dynamic NodeACLs during cached demo-mode operation
commit
fcf29481fb8e106daad6688f2e898226ee928992 upstream.
This patch fixes a bug in core_tpg_check_initiator_node_acl() ->
core_tpg_get_initiator_node_acl() where a dynamically created
se_node_acl generated during session login would be skipped during
subsequent lookup due to the '!acl->dynamic_node_acl' check, causing
a new se_node_acl to be created with a duplicate ->initiatorname.
This would occur when a fabric endpoint was configured with
TFO->tpg_check_demo_mode()=1 + TPF->tpg_check_demo_mode_cache()=1
preventing the release of an existing se_node_acl during se_session
shutdown.
Also, drop the unnecessary usage of core_tpg_get_initiator_node_acl()
within core_dev_init_initiator_node_lun_acl() that originally
required the extra '!acl->dynamic_node_acl' check, and just pass
the configfs provided se_node_acl pointer instead.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
[bwh: Backported to 3.2: adjust context, filename of header]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Jussi Kivilinna [Mon, 18 Feb 2013 08:29:30 +0000 (10:29 +0200)]
rtlwifi: usb: allocate URB control message setup_packet and data buffer separately
commit
bc6b89237acb3dee6af6e64e51a18255fef89cc2 upstream.
rtlwifi allocates both setup_packet and data buffer of control message urb,
using shared kmalloc in _usbctrl_vendorreq_async_write. Structure used for
allocating is:
struct {
u8 data[254];
struct usb_ctrlrequest dr;
};
Because 'struct usb_ctrlrequest' is __packed, setup packet is unaligned and
DMA mapping of both 'data' and 'dr' confuses ARM/sunxi, leading to memory
corruptions and freezes.
Patch changes setup packet to be allocated separately.
[v2]:
- Use WARN_ON_ONCE instead of WARN_ON
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Linus Torvalds [Mon, 18 Feb 2013 17:58:02 +0000 (09:58 -0800)]
mm: fix pageblock bitmap allocation
commit
7c45512df987c5619db041b5c9b80d281e26d3db upstream.
Commit
c060f943d092 ("mm: use aligned zone start for pfn_to_bitidx
calculation") fixed out calculation of the index into the pageblock
bitmap when a !SPARSEMEM zome was not aligned to pageblock_nr_pages.
However, the _allocation_ of that bitmap had never taken this alignment
requirement into accout, so depending on the exact size and alignment of
the zone, the use of that index could then access past the allocation,
resulting in some very subtle memory corruption.
This was reported (and bisected) by Ingo Molnar: one of his random
config builds would hang with certain very specific kernel command line
options.
In the meantime, commit
c060f943d092 has been marked for stable, so this
fix needs to be back-ported to the stable kernels that backported the
commit to use the right alignment.
Bisected-and-tested-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Lukas Czerner [Mon, 18 Feb 2013 17:12:07 +0000 (12:12 -0500)]
ext4: fix xattr block allocation/release with bigalloc
commit
1231b3a1eb5740192aeebf5344dd6d6da000febf upstream.
Currently when new xattr block is created or released we we would call
dquot_free_block() or dquot_alloc_block() respectively, among the else
decrementing or incrementing the number of blocks assigned to the
inode by one block.
This however does not work for bigalloc file system because we always
allocate/free the whole cluster so we have to count with that in
dquot_free_block() and dquot_alloc_block() as well.
Use the clusters-to-blocks conversion EXT4_C2B() when passing number of
blocks to the dquot_alloc/free functions to fix the problem.
The problem has been revealed by xfstests #117 (and possibly others).
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Li Zefan [Fri, 25 Jan 2013 08:08:01 +0000 (16:08 +0800)]
cpuset: fix cpuset_print_task_mems_allowed() vs rename() race
commit
63f43f55c9bbc14f76b582644019b8a07dc8219a upstream.
rename() will change dentry->d_name. The result of this race can
be worse than seeing partially rewritten name, but we might access
a stale pointer because rename() will re-allocate memory to hold
a longer name.
It's safe in the protection of dentry->d_lock.
v2: check NULL dentry before acquiring dentry lock.
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Li Zefan [Thu, 24 Jan 2013 06:43:28 +0000 (14:43 +0800)]
cgroup: fix exit() vs rmdir() race
commit
71b5707e119653039e6e95213f00479668c79b75 upstream.
In cgroup_exit() put_css_set_taskexit() is called without any lock,
which might lead to accessing a freed cgroup:
thread1 thread2
---------------------------------------------
exit()
cgroup_exit()
put_css_set_taskexit()
atomic_dec(cgrp->count);
rmdir();
/* not safe !! */
check_for_release(cgrp);
rcu_read_lock() can be used to make sure the cgroup is alive.
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
fanchaoting [Mon, 4 Feb 2013 13:15:02 +0000 (21:15 +0800)]
umount oops when remove blocklayoutdriver first
commit
5a12cca697aca5dfba42a7d4c3356acc0445a2b0 upstream.
now pnfs client uses block layout, maybe we can remove
blocklayoutdriver first. if we umount later,
it can cause oops in unset_pnfs_layoutdriver.
because nfss->pnfs_curr_ld->clear_layoutdriver is invalid.
reproduce it:
modprobe blocklayoutdriver
mount -t nfs4 -o minorversion=1 pnfsip:/ /mnt/
rmmod blocklayoutdriver
umount /mnt
then you can see following
CPU 0
Pid: 17023, comm: umount.nfs4 Tainted: GF O 3.7.0-rc6-pnfs #1 VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform
RIP: 0010:[<
ffffffffa04cfe6d>] [<
ffffffffa04cfe6d>] unset_pnfs_layoutdriver+0x1d/0x70 [nfsv4]
RSP: 0018:
ffff8800022d9e48 EFLAGS:
00010286
RAX:
ffffffffa04a1b00 RBX:
ffff88000b013800 RCX:
0000000000000001
RDX:
ffffffff81ae8ee0 RSI:
ffff880001ee94b8 RDI:
ffff88000b013800
RBP:
ffff8800022d9e58 R08:
0000000000000001 R09:
0000000000000000
R10:
0000000000000000 R11:
0000000000000000 R12:
ffff880001ee9400
R13:
ffff8800105978c0 R14:
00007fff25846c08 R15:
0000000001bba550
FS:
00007f45ae7f0700(0000) GS:
ffff880012c00000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
000000008005003b
CR2:
ffffffffa04a1b38 CR3:
0000000002c0c000 CR4:
00000000000006f0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000ffff0ff0 DR7:
0000000000000400
Process umount.nfs4 (pid: 17023, threadinfo
ffff8800022d8000, task
ffff880006e48aa0)
Stack:
ffff8800105978c0 ffff88000b013800 ffff8800022d9e78 ffffffffa04cd0ce
ffff8800022d9e78 ffff88000b013800 ffff8800022d9ea8 ffffffffa04755a7
ffff8800022d9ea8 ffff880002f96400 ffff88000b013800 ffff880002f96400
Call Trace:
[<
ffffffffa04cd0ce>] nfs4_destroy_server+0x1e/0x30 [nfsv4]
[<
ffffffffa04755a7>] nfs_free_server+0xb7/0x150 [nfs]
[<
ffffffffa047d4d5>] nfs_kill_super+0x35/0x40 [nfs]
[<
ffffffff81178d35>] deactivate_locked_super+0x45/0x70
[<
ffffffff8117986a>] deactivate_super+0x4a/0x70
[<
ffffffff81193ee2>] mntput_no_expire+0xd2/0x130
[<
ffffffff81194d62>] sys_umount+0x72/0xe0
[<
ffffffff8154af59>] system_call_fastpath+0x16/0x1b
Code: 06 e1 b8 ea ff ff ff eb 9e 0f 1f 44 00 00 55 48 89 e5 53 48 83 ec 08 66 66 66 66 90 48 8b 87 80 03 00 00 48 89 fb 48 85 c0 74 29 <48> 8b 40 38 48 85 c0 74 02 ff d0 48 8b 03 3e ff 48 04 0f 94 c2
RIP [<
ffffffffa04cfe6d>] unset_pnfs_layoutdriver+0x1d/0x70 [nfsv4]
RSP <
ffff8800022d9e48>
CR2:
ffffffffa04a1b38
---[ end trace
29f75aaedda058bf ]---
Signed-off-by: fanchaoting<fanchaoting@cn.fujitsu.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Weston Andros Adamson [Fri, 15 Feb 2013 21:03:46 +0000 (16:03 -0500)]
NFSv4.1: Don't decode skipped layoutgets
commit
085b7a45c63d3da5be155faab9249a5cab224561 upstream.
layoutget's prepare hook can call rpc_exit with status = NFS4_OK (0).
Because of this, nfs4_proc_layoutget can't depend on a 0 status to mean
that the RPC was successfully sent, received and parsed.
To fix this, use the result's len member to see if parsing took place.
This fixes the following OOPS -- calling xdr_init_decode() with a buffer length
0 doesn't set the stream's 'p' member and ends up using uninitialized memory
in filelayout_decode_layout.
BUG: unable to handle kernel paging request at
0000000000008050
IP: [<
ffffffff81282e78>] memcpy+0x18/0x120
PGD 0
Oops: 0000 [#1] SMP
last sysfs file: /sys/devices/pci0000:00/0000:00:11.0/0000:02:01.0/irq
CPU 1
Modules linked in: nfs_layout_nfsv41_files nfs lockd fscache auth_rpcgss nfs_acl autofs4 sunrpc ipt_REJECT nf_conntrack_ipv4 nf_defrag_ipv4 iptable_filter ip_tables ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 xt_state nf_conntrack ip6table_filter ip6_tables ipv6 dm_mirror dm_region_hash dm_log dm_mod ppdev parport_pc parport snd_ens1371 snd_rawmidi snd_ac97_codec ac97_bus snd_seq snd_seq_device snd_pcm snd_timer snd soundcore snd_page_alloc e1000 microcode vmware_balloon i2c_piix4 i2c_core sg shpchp ext4 mbcache jbd2 sr_mod cdrom sd_mod crc_t10dif pata_acpi ata_generic ata_piix mptspi mptscsih mptbase scsi_transport_spi [last unloaded: speedstep_lib]
Pid: 1665, comm: flush-0:22 Not tainted 2.6.32-356-test-2 #2 VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform
RIP: 0010:[<
ffffffff81282e78>] [<
ffffffff81282e78>] memcpy+0x18/0x120
RSP: 0018:
ffff88003dfab588 EFLAGS:
00010206
RAX:
ffff88003dc42000 RBX:
ffff88003dfab610 RCX:
0000000000000009
RDX:
000000003f807ff0 RSI:
0000000000008050 RDI:
ffff88003dc42000
RBP:
ffff88003dfab5b0 R08:
0000000000000000 R09:
0000000000000000
R10:
0000000000000000 R11:
0000000000000080 R12:
0000000000000024
R13:
ffff88003dc42000 R14:
ffff88003f808030 R15:
ffff88003dfab6a0
FS:
0000000000000000(0000) GS:
ffff880003420000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0:
000000008005003b
CR2:
0000000000008050 CR3:
000000003bc92000 CR4:
00000000001407e0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000ffff0ff0 DR7:
0000000000000400
Process flush-0:22 (pid: 1665, threadinfo
ffff88003dfaa000, task
ffff880037f77540)
Stack:
ffffffffa0398ac1 ffff8800397c5940 ffff88003dfab610 ffff88003dfab6a0
<d>
ffff88003dfab5d0 ffff88003dfab680 ffffffffa01c150b ffffea0000d82e70
<d>
000000508116713b 0000000000000000 0000000000000000 0000000000000000
Call Trace:
[<
ffffffffa0398ac1>] ? xdr_inline_decode+0xb1/0x120 [sunrpc]
[<
ffffffffa01c150b>] filelayout_decode_layout+0xeb/0x350 [nfs_layout_nfsv41_files]
[<
ffffffffa01c17fc>] filelayout_alloc_lseg+0x8c/0x3c0 [nfs_layout_nfsv41_files]
[<
ffffffff8150e6ce>] ? __wait_on_bit+0x7e/0x90
Signed-off-by: Weston Andros Adamson <dros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
J. Bruce Fields [Sun, 10 Feb 2013 16:33:48 +0000 (11:33 -0500)]
svcrpc: make svc_age_temp_xprts enqueue under sv_lock
commit
e75bafbff2270993926abcc31358361db74a9bc2 upstream.
svc_age_temp_xprts expires xprts in a two-step process: first it takes
the sv_lock and moves the xprts to expire off their server-wide list
(sv_tempsocks or sv_permsocks) to a local list. Then it drops the
sv_lock and enqueues and puts each one.
I see no reason for this: svc_xprt_enqueue() will take sp_lock, but the
sv_lock and sp_lock are not otherwise nested anywhere (and documentation
at the top of this file claims it's correct to nest these with sp_lock
inside.)
Tested-by: Jason Tibbitts <tibbs@math.uh.edu>
Tested-by: Paweł Sikora <pawel.sikora@agmk.net>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Stanislaw Gruszka [Fri, 15 Feb 2013 10:08:11 +0000 (11:08 +0100)]
posix-cpu-timers: Fix nanosleep task_struct leak
commit
e6c42c295e071dd74a66b5a9fcf4f44049888ed8 upstream.
The trinity fuzzer triggered a task_struct reference leak via
clock_nanosleep with CPU_TIMERs. do_cpu_nanosleep() calls
posic_cpu_timer_create(), but misses a corresponding
posix_cpu_timer_del() which leads to the task_struct reference leak.
Reported-and-tested-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Dave Jones <davej@redhat.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Link: http://lkml.kernel.org/r/20130215100810.GF4392@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Josh Boyer [Thu, 14 Feb 2013 14:39:09 +0000 (09:39 -0500)]
USB: usb-storage: unusual_devs update for Super TOP SATA bridge
commit
18e03310b5caa6d11c1a8c61b982c37047693fba upstream.
The current entry in unusual_cypress.h for the Super TOP SATA bridge devices
seems to be causing corruption on newer revisions of this device. This has
been reported in Arch Linux and Fedora. The original patch was tested on
devices with bcdDevice of 1.60, whereas the newer devices report bcdDevice
as 2.20. Limit the UNUSUAL_DEV entry to devices less than 2.20.
This fixes https://bugzilla.redhat.com/show_bug.cgi?id=909591
The Arch Forum post on this is here:
https://bbs.archlinux.org/viewtopic.php?id=152011
Reported-by: Carsten S. <carsteniq@yahoo.com>
Tested-by: Carsten S. <carsteniq@yahoo.com>
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Roger Quadros [Thu, 14 Feb 2013 15:08:09 +0000 (17:08 +0200)]
USB: ehci-omap: Fix autoloading of module
commit
04753523266629b1cd0518091da1658755787198 upstream.
The module alias should be "ehci-omap" and not
"omap-ehci" to match the platform device name.
The omap-ehci module should now autoload correctly.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Arnd Bergmann [Mon, 14 Jan 2013 12:49:02 +0000 (12:49 +0000)]
ARM: w90x900: fix legacy assembly syntax
commit
fa5ce5f94c0f2bfa41ba68d2d2524298e1fc405e upstream.
New ARM binutils don't allow extraneous whitespace inside
of brackets, which causes this error on all mach-w90x900
defconfigs:
arch/arm/kernel/entry-armv.S: Assembler messages:
arch/arm/kernel/entry-armv.S:214: Error: ARM register expected -- `ldr r0,[ r6,#(0x10C)]'
arch/arm/kernel/entry-armv.S:214: Error: ARM register expected -- `ldr r0,[ r6,#(0x110)]'
arch/arm/kernel/entry-armv.S:430: Error: ARM register expected -- `ldr r0,[ r6,#(0x10C)]'
arch/arm/kernel/entry-armv.S:430: Error: ARM register expected -- `ldr r0,[ r6,#(0x110)]'
This removes the whitespace in order to build the kernel
again.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Arnd Bergmann [Tue, 8 Jan 2013 21:58:31 +0000 (21:58 +0000)]
ARM: samsung: fix assembly syntax for new gas
commit
2815774bb38445006074e16251b9ef5123bdc616 upstream.
Recent assembler versions complain about extraneous
whitespace inside [] brackets. This fixes all of
these instances for the samsung platforms. We should
backport this to all kernels that might need to
be built with new binutils.
arch/arm/kernel/entry-armv.S: Assembler messages:
arch/arm/kernel/entry-armv.S:214: Error: ARM register expected -- `ldr r2,[ r6,#(0x10)]'
arch/arm/kernel/entry-armv.S:214: Error: ARM register expected -- `ldr r0,[ r6,#(0x14)]'
arch/arm/kernel/entry-armv.S:430: Error: ARM register expected -- `ldr r2,[ r6,#(0x10)]'
arch/arm/kernel/entry-armv.S:430: Error: ARM register expected -- `ldr r0,[ r6,#(0x14)]'
arch/arm/mach-s3c24xx/sleep-s3c2410.S: Assembler messages:
arch/arm/mach-s3c24xx/sleep-s3c2410.S:48: Error: ARM register expected -- `ldr r7,[ r4 ]'
arch/arm/mach-s3c24xx/sleep-s3c2410.S:49: Error: ARM register expected -- `ldr r8,[ r5 ]'
arch/arm/mach-s3c24xx/sleep-s3c2410.S:50: Error: ARM register expected -- `ldr r9,[ r6 ]'
arch/arm/mach-s3c24xx/sleep-s3c2410.S:64: Error: ARM register expected -- `streq r7,[ r4 ]'
arch/arm/mach-s3c24xx/sleep-s3c2410.S:65: Error: ARM register expected -- `streq r8,[ r5 ]'
arch/arm/mach-s3c24xx/sleep-s3c2410.S:66: Error: ARM register expected -- `streq r9,[ r6 ]'
arch/arm/kernel/debug.S: Assembler messages:
arch/arm/kernel/debug.S:83: Error: ARM register expected -- `ldr r2,[ r2,#((0x0B0)+(((0x56000000)-(0x50000000))+(0xF6000000+(0x01000000))))-((0)+(((0x56000000)-(0x50000000))+(0xF6000000+(0x01000000))))]'
arch/arm/kernel/debug.S:83: Error: ARM register expected -- `ldr r2,[ r3,#(0x18)]'
arch/arm/kernel/debug.S:85: Error: ARM register expected -- `ldr r2,[ r2,#((0x0B0)+(((0x56000000)-(0x50000000))+(0xF6000000+(0x01000000))))-((0)+(((0x56000000)-(0x50000000))+(0xF6000000+(0x01000000))))]'
arch/arm/kernel/debug.S:85: Error: ARM register expected -- `ldr r2,[ r3,#(0x18)]'
arch/arm/mach-s3c24xx/pm-h1940.S: Assembler messages:
arch/arm/mach-s3c24xx/pm-h1940.S:33: Error: ARM register expected -- `ldr pc,[ r0,#((0x0B8)+(((0x56000000)-(0x50000000))+(0xF6000000+(0x01000000))))-(((0x56000000)-(0x50000000))+(0xF6000000+(0x01000000)))]'
arch/arm/mach-s3c24xx/sleep-s3c2412.S: Assembler messages:
arch/arm/mach-s3c24xx/sleep-s3c2412.S:60: Error: ARM register expected -- `ldrne r9,[ r1 ]'
arch/arm/mach-s3c24xx/sleep-s3c2412.S:61: Error: ARM register expected -- `strne r9,[ r1 ]'
arch/arm/mach-s3c24xx/sleep-s3c2412.S:62: Error: ARM register expected -- `ldrne r9,[ r2 ]'
arch/arm/mach-s3c24xx/sleep-s3c2412.S:63: Error: ARM register expected -- `strne r9,[ r2 ]'
arch/arm/mach-s3c24xx/sleep-s3c2412.S:64: Error: ARM register expected -- `ldrne r9,[ r3 ]'
arch/arm/mach-s3c24xx/sleep-s3c2412.S:65: Error: ARM register expected -- `strne r9,[ r3 ]'
arch/arm/kernel/debug.S:83: Error: ARM register expected -- `ldr r2,[ r3,#(0x08)]'
arch/arm/kernel/debug.S:83: Error: ARM register expected -- `ldr r2,[ r3,#(0x18)]'
arch/arm/kernel/debug.S:83: Error: ARM register expected -- `ldr r2,[ r3,#(0x10)]'
arch/arm/kernel/debug.S:85: Error: ARM register expected -- `ldr r2,[ r3,#(0x08)]'
arch/arm/kernel/debug.S:85: Error: ARM register expected -- `ldr r2,[ r3,#(0x18)]'
arch/arm/kernel/debug.S:85: Error: ARM register expected -- `ldr r2,[ r3,#(0x10)]'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
[bwh: Backported to 3.2: adjust filenames]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Satoru Takeuchi [Thu, 14 Feb 2013 00:12:52 +0000 (09:12 +0900)]
efi: Clear EFI_RUNTIME_SERVICES rather than EFI_BOOT by "noefi" boot parameter
commit
1de63d60cd5b0d33a812efa455d5933bf1564a51 upstream.
There was a serious problem in samsung-laptop that its platform driver is
designed to run under BIOS and running under EFI can cause the machine to
become bricked or can cause Machine Check Exceptions.
Discussion about this problem:
https://bugs.launchpad.net/ubuntu-cdimage/+bug/1040557
https://bugzilla.kernel.org/show_bug.cgi?id=47121
The patches to fix this problem:
efi: Make 'efi_enabled' a function to query EFI facilities
83e68189745ad931c2afd45d8ee3303929233e7f
samsung-laptop: Disable on EFI hardware
e0094244e41c4d0c7ad69920681972fc45d8ce34
Unfortunately this problem comes back again if users specify "noefi" option.
This parameter clears EFI_BOOT and that driver continues to run even if running
under EFI. Refer to the document, this parameter should clear
EFI_RUNTIME_SERVICES instead.
Documentation/kernel-parameters.txt:
===============================================================================
...
noefi [X86] Disable EFI runtime services support.
...
===============================================================================
Documentation/x86/x86_64/uefi.txt:
===============================================================================
...
- If some or all EFI runtime services don't work, you can try following
kernel command line parameters to turn off some or all EFI runtime
services.
noefi turn off all EFI runtime services
...
===============================================================================
Signed-off-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Link: http://lkml.kernel.org/r/511C2C04.2070108@jp.fujitsu.com
Cc: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Bjørn Mork [Wed, 13 Feb 2013 22:41:34 +0000 (23:41 +0100)]
USB: option: add Huawei "ACM" devices using protocol = vendor
commit
1f3f687722fd9b29a0c2a85b4844e3b2a3585c63 upstream.
The USB device descriptor of one identity presented by a few
Huawei morphing devices have serial functions with class codes
02/02/ff, indicating CDC ACM with a vendor specific protocol. This
combination is often used for MSFT RNDIS functions, and the CDC
ACM class driver will therefore ignore such functions.
The CDC ACM class driver cannot support functions with only 2
endpoints. The underlying serial functions of these modems are
also believed to be the same as for alternate device identities
already supported by the option driver. Letting the same driver
handle these functions independently of the current identity
ensures consistent handling and user experience.
There is no need to blacklist these devices in the rndis_host
driver. Huawei serial functions will either have only 2 endpoints
or a CDC ACM functional descriptor with bmCapabilities != 0, making
them correctly ignored as "non RNDIS" by that driver.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Rafael J. Wysocki [Mon, 11 Feb 2013 19:49:49 +0000 (20:49 +0100)]
PCI/PM: Clean up PME state when removing a device
commit
249bfb83cf8ba658955f0245ac3981d941f746ee upstream.
Devices are added to pci_pme_list when drivers use pci_enable_wake()
or pci_wake_from_d3(), but they aren't removed from the list unless
the driver explicitly disables wakeup. Many drivers never disable
wakeup, so their devices remain on the list even after they are
removed, e.g., via hotplug. A subsequent PME poll will oops when
it tries to touch the device.
This patch disables PME# on a device before removing it, which removes
the device from pci_pme_list. This is safe even if the device never
had PME# enabled.
This oops can be triggered by unplugging a Thunderbolt ethernet adapter
on a Macbook Pro, as reported by Daniel below.
[bhelgaas: changelog]
Reference: http://lkml.kernel.org/r/CAMVG2svG21yiM1wkH4_2pen2n+cr2-Zv7TbH3Gj+8MwevZjDbw@mail.gmail.com
Reported-and-tested-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
George Spelvin [Tue, 12 Feb 2013 07:27:20 +0000 (02:27 -0500)]
pps: Fix a use-after free bug when unregistering a source.
commit
d953e0e837e65ecc1ddaa4f9560f7925878a0de6 upstream.
Remove the cdev from the system (with cdev_del) *before* deallocating it
(in pps_device_destruct, called via kobject_put from device_destroy).
Also prevent deallocating a device with open file handles.
A better long-term fix is probably to remove the cdev from the pps_device
entirely, and instead have all devices reference one global cdev. Then
the deallocation ordering becomes simpler.
But that's more complex and invasive change, so we leave that
for later.
Signed-off-by: George Spelvin <linux@horizon.com>
Acked-by: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
George Spelvin [Sun, 10 Feb 2013 09:41:56 +0000 (04:41 -0500)]
pps: Use pps_lookup_dev to reduce ldisc coupling
commit
03a7ffe4e542310838bac70ef85acc17536b6d7c upstream.
Now that N_TTY uses tty->disc_data for its private data,
'subclass' ldiscs cannot use ->disc_data for their own private data.
(This is a regression is v3.8-rc1)
Use pps_lookup_dev to associate the tty with the pps source instead.
This fixes a crashing regression in 3.8-rc1.
Signed-off-by: George Spelvin <linux@horizon.com>
Acked-by: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
George Spelvin [Sun, 10 Feb 2013 09:08:32 +0000 (04:08 -0500)]
pps: Add pps_lookup_dev() function
commit
513b032c98b4b9414aa4e9b4a315cb1bf0380101 upstream.
The PPS serial line discipline wants to attach a PPS device to a tty
without changing the tty code to add a struct pps_device * pointer.
Since the number of PPS devices in a typical system is generally very low
(n=1 is by far the most common), it's practical to search the entire list
of allocated pps devices. (We capture the timestamp before the lookup,
so the timing isn't affected.)
It is a bit ugly that this function, which is part of the in-kernel
PPS API, has to be in pps.c as opposed to kapi,c, but that's not
something that affects users.
Signed-off-by: George Spelvin <linux@horizon.com>
Acked-by: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Philipp Reisner [Wed, 20 Jul 2011 12:59:37 +0000 (14:59 +0200)]
idr: idr_for_each_entry() macro
commit
9749f30f1a387070e6e8351f35aeb829eacc3ab6 upstream.
Inspired by the list_for_each_entry() macro
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Johan Hovold [Wed, 13 Feb 2013 16:53:28 +0000 (17:53 +0100)]
USB: serial: fix null-pointer dereferences on disconnect
commit
b2ca699076573c94fee9a73cb0d8645383b602a0 upstream.
Make sure serial-driver dtr_rts is called with disc_mutex held after
checking the disconnected flag.
Due to a bug in the tty layer, dtr_rts may get called after a device has
been disconnected and the tty-device unregistered. Some drivers have had
individual checks for disconnect to make sure the disconnected interface
was not accessed, but this should really be handled in usb-serial core
(at least until the long-standing tty-bug has been fixed).
Note that the problem has been made more acute with commit
0998d0631001
("device-core: Ensure drvdata = NULL when no driver is bound") as the
port data is now also NULL when dtr_rts is called resulting in further
oopses.
Reported-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2:
- Adjust context
- Drop changes to quatech2.c]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Bjørn Mork [Tue, 12 Feb 2013 12:42:24 +0000 (13:42 +0100)]
USB: option: add Yota / Megafon M100-1 4g modem
commit
cd565279e51bedee1b2988e84f9b3bef485adeb6 upstream.
Interface layout:
00 CD-ROM
01 debug COM port
02 AP control port
03 modem
04 usb-ethernet
Bus=01 Lev=02 Prnt=02 Port=01 Cnt=02 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0408 ProdID=ea42 Rev= 0.00
S: Manufacturer=Qualcomm, Incorporated
S: Product=Qualcomm CDMA Technologies MSM
S: SerialNumber=353568051xxxxxx
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=84(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=86(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Daniel Vetter [Wed, 13 Feb 2013 10:37:48 +0000 (20:37 +1000)]
Revert "drm: Add EDID_QUIRK_FORCE_REDUCED_BLANKING for ASUS VW222S"
commit
db3985e5ca8f50fc17606855ba394783d11683a5 upstream.
This reverts commit
6f33814bd4d9cfe76033a31b1c0c76c960cd8e4b.
The quirk cause a regression, and it looks like the original bug was
simply a lack of FIFO bandwidth on the i915G of the reporter. Which
should eventually be fixed as soon as we get around to implemented
DSPARB FIFO reassignment on gen 3.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=52281
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Mel Gorman [Mon, 11 Feb 2013 14:52:36 +0000 (14:52 +0000)]
x86/mm: Check if PUD is large when validating a kernel address
commit
0ee364eb316348ddf3e0dfcd986f5f13f528f821 upstream.
A user reported the following oops when a backup process reads
/proc/kcore:
BUG: unable to handle kernel paging request at
ffffbb00ff33b000
IP: [<
ffffffff8103157e>] kern_addr_valid+0xbe/0x110
[...]
Call Trace:
[<
ffffffff811b8aaa>] read_kcore+0x17a/0x370
[<
ffffffff811ad847>] proc_reg_read+0x77/0xc0
[<
ffffffff81151687>] vfs_read+0xc7/0x130
[<
ffffffff811517f3>] sys_read+0x53/0xa0
[<
ffffffff81449692>] system_call_fastpath+0x16/0x1b
Investigation determined that the bug triggered when reading
system RAM at the 4G mark. On this system, that was the first
address using 1G pages for the virt->phys direct mapping so the
PUD is pointing to a physical address, not a PMD page.
The problem is that the page table walker in kern_addr_valid() is
not checking pud_large() and treats the physical address as if
it was a PMD. If it happens to look like pmd_none then it'll
silently fail, probably returning zeros instead of real data. If
the data happens to look like a present PMD though, it will be
walked resulting in the oops above.
This patch adds the necessary pud_large() check.
Unfortunately the problem was not readily reproducible and now
they are running the backup program without accessing
/proc/kcore so the patch has not been validated but I think it
makes sense.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Reviewed-by: Rik van Riel <riel@redhat.coM>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20130211145236.GX21389@suse.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Olaf Hering [Mon, 4 Feb 2013 01:22:37 +0000 (17:22 -0800)]
x86: Hyper-V: register clocksource only if its advertised
commit
32068f6527b8f1822a30671dedaf59c567325026 upstream.
Enable hyperv_clocksource only if its advertised as a feature.
XenServer 6 returns the signature which is checked in
ms_hyperv_platform(), but it does not offer all features. Currently the
clocksource is enabled unconditionally in ms_hyperv_init_platform(), and
the result is a hanging guest.
Hyper-V spec Bit 1 indicates the availability of Partition Reference
Counter. Register the clocksource only if this bit is set.
The guest in question prints this in dmesg:
[ 0.000000] Hypervisor detected: Microsoft HyperV
[ 0.000000] HyperV: features 0x70, hints 0x0
This bug can be reproduced easily be setting 'viridian=1' in a HVM domU
.cfg file. A workaround without this patch is to boot the HVM guest with
'clocksource=jiffies'.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Link: http://lkml.kernel.org/r/1359940959-32168-1-git-send-email-kys@microsoft.com
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Linus Walleij [Tue, 12 Feb 2013 21:46:19 +0000 (13:46 -0800)]
drivers/rtc/rtc-pl031.c: restore ST variant functionality
commit
3399cfb5df9594495b876d1843a7165f77366b2b upstream.
Commit
e7e034e18a0a ("drivers/rtc/rtc-pl031.c: fix the missing operation
on enable") accidentally broke the ST variants of PL031.
The bit that is being poked as "clockwatch" enable bit for the ST
variants does the work of bit 0 on this variant. Bit 0 is used for a
clock divider on the ST variants, and setting it to 1 will affect
timekeeping in a very bad way.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Mian Yousaf KAUKAB <mian.yousaf.kaukab@stericsson.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Denis Efremov [Mon, 11 Feb 2013 15:49:48 +0000 (19:49 +0400)]
ALSA: ali5451: remove irq enabling in pointer callback
commit
dacae5a19b4cbe1b5e3a86de23ea74cbe9ec9652 upstream.
snd_ali_pointer function is called with local
interrupts disabled. However it seems very strange to
reenable them in such way.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Denis Efremov <yefremov.denis@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Denis Efremov [Mon, 11 Feb 2013 15:04:06 +0000 (19:04 +0400)]
ALSA: rme32.c irq enabling after spin_lock_irq
commit
f49a59c4471d81a233e09dda45187cc44fda009d upstream.
According to the other code in this driver and similar
code in rme96 it seems, that spin_lock_irq in
snd_rme32_capture_close function should be paired
with spin_unlock_irq.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Denis Efremov <yefremov.denis@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Stoney Wang [Thu, 7 Feb 2013 18:53:02 +0000 (10:53 -0800)]
x86/apic: Work around boot failure on HP ProLiant DL980 G7 Server systems
commit
cb214ede7657db458fd0b2a25ea0b28dbf900ebc upstream.
When a HP ProLiant DL980 G7 Server boots a regular kernel,
there will be intermittent lost interrupts which could
result in a hang or (in extreme cases) data loss.
The reason is that this system only supports x2apic physical
mode, while the kernel boots with a logical-cluster default
setting.
This bug can be worked around by specifying the "x2apic_phys" or
"nox2apic" boot option, but we want to handle this system
without requiring manual workarounds.
The BIOS sets ACPI_FADT_APIC_PHYSICAL in FADT table.
As all apicids are smaller than 255, BIOS need to pass the
control to the OS with xapic mode, according to x2apic-spec,
chapter 2.9.
Current code handle x2apic when BIOS pass with xapic mode
enabled:
When user specifies x2apic_phys, or FADT indicates PHYSICAL:
1. During madt oem check, apic driver is set with xapic logical
or xapic phys driver at first.
2. enable_IR_x2apic() will enable x2apic_mode.
3. if user specifies x2apic_phys on the boot line, x2apic_phys_probe()
will install the correct x2apic phys driver and use x2apic phys mode.
Otherwise it will skip the driver will let x2apic_cluster_probe to
take over to install x2apic cluster driver (wrong one) even though FADT
indicates PHYSICAL, because x2apic_phys_probe does not check
FADT PHYSICAL.
Add checking x2apic_fadt_phys in x2apic_phys_probe() to fix the
problem.
Signed-off-by: Stoney Wang <song-bo.wang@hp.com>
[ updated the changelog and simplified the code ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1360263182-16226-1-git-send-email-yinghai@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Greg Pearson [Wed, 25 Apr 2012 00:23:56 +0000 (18:23 -0600)]
x86/apic: Use x2apic physical mode based on FADT setting
commit
ea0dcf903e7d76aa5d483d876215fedcfdfe140f upstream.
Provide systems that do not support x2apic cluster mode
a mechanism to select x2apic physical mode using the
FADT FORCE_APIC_PHYSICAL_DESTINATION_MODE bit.
Changes from v1: (based on Suresh's comments)
- removed #ifdef CONFIG_ACPI
- removed #include <linux/acpi.h>
Signed-off-by: Greg Pearson <greg.pearson@hp.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1335313436-32020-1-git-send-email-greg.pearson@hp.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
fangxiaozhi [Thu, 7 Feb 2013 07:32:07 +0000 (15:32 +0800)]
USB: storage: properly handle the endian issues of idProduct
commit
cd060956c5e97931c3909e4a808508469c0bb9f6 upstream.
1. The idProduct is little endian, so make sure its value to be
compatible with the current CPU. Make no break on big endian processors.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Larry Finger [Fri, 8 Feb 2013 18:28:18 +0000 (12:28 -0600)]
rtlwifi: rtl8192cu: Add new USB ID
commit
8708aac79e4572ba673d7a21e94ddca9f3abb7fc upstream.
A new model of the RTL8188CUS has appeared.
Reported-and-tested-by: Thomas Rosenkrantz <tom.rosary@googlemail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Larry Finger [Wed, 6 Feb 2013 18:54:17 +0000 (12:54 -0600)]
rtlwifi: rtl8192cu: Fix NULL dereference BUG when using new_id
commit
957f4aca5fa0db69635271bc4621cc0b65b2d590 upstream.
When the new_id entry in /sysfs is used for a foreign USB device, rtlwifi
BUGS with a NULL pointer dereference because the per-driver configuration
data is not available. The probe function has been restructured as
suggested by Ben Hutchings <bhutchings@solarflare.com>.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[bwh: Backported to 3.2: adjust context, indentation]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tomasz Guszkowski [Tue, 5 Feb 2013 21:10:31 +0000 (22:10 +0100)]
p54usb: corrected USB ID for T-Com Sinus 154 data II
commit
008e33f733ca51acb2dd9d88ea878693b04d1d2a upstream.
Corrected USB ID for T-Com Sinus 154 data II. ISL3887-based. The
device was tested in managed mode with no security, WEP 128
bit and WPA-PSK (TKIP) with firmware 2.13.1.0.lm87.arm (md5sum:
7d676323ac60d6e1a3b6d61e8c528248). It works.
Signed-off-by: Tomasz Guszkowski <tsg@o2.pl>
Acked-By: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Takashi Iwai [Fri, 25 Jan 2013 00:28:18 +0000 (10:28 +1000)]
fb: Yet another band-aid for fixing lockdep mess
commit
e93a9a868792ad71cdd09d75e5a02d8067473c4e upstream.
I've still got lockdep warnings even after Alan's patch, and it seems that
yet more band aids are required to paper over similar paths for
unbind_con_driver() and unregister_con_driver(). After this hack, lockdep
warnings are finally gone.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Alan Cox [Fri, 25 Jan 2013 00:28:15 +0000 (10:28 +1000)]
fb: rework locking to fix lock ordering on takeover
commit
50e244cc793d511b86adea24972f3a7264cae114 upstream.
Adjust the console layer to allow a take over call where the caller
already holds the locks. Make the fb layer lock in order.
This is partly a band aid, the fb layer is terminally confused about the
locking rules it uses for its notifiers it seems.
[akpm@linux-foundation.org: remove stray non-ascii char, tidy comment]
[akpm@linux-foundation.org: export do_take_over_console()]
[airlied: cleanup another non-ascii char]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Jiri Kosina <jkosina@suse.cz>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
H. Peter Anvin [Fri, 8 Feb 2013 01:14:08 +0000 (17:14 -0800)]
timeconst.pl: Eliminate Perl warning
commit
63a3f603413ffe82ad775f2d62a5afff87fd94a0 upstream.
defined(@array) is deprecated in Perl and gives off a warning.
Restructure the code to remove that warning.
[ hpa: it would be interesting to revert to the timeconst.bc script.
It appears that the failures reported by akpm during testing of
that script was due to a known broken version of make, not a problem
with bc. The Makefile rules could probably be restructured to avoid
the make bug, or it is probably old enough that it doesn't matter. ]
Reported-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Kees Cook [Thu, 7 Feb 2013 17:44:13 +0000 (09:44 -0800)]
x86: Do not leak kernel page mapping locations
commit
e575a86fdc50d013bf3ad3aa81d9100e8e6cc60d upstream.
Without this patch, it is trivial to determine kernel page
mappings by examining the error code reported to dmesg[1].
Instead, declare the entire kernel memory space as a violation
of a present page.
Additionally, since show_unhandled_signals is enabled by
default, switch branch hinting to the more realistic
expectation, and unobfuscate the setting of the PF_PROT bit to
improve readability.
[1] http://vulnfactory.org/blog/2013/02/06/a-linux-memory-trick/
Reported-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Suggested-by: Brad Spengler <spender@grsecurity.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20130207174413.GA12485@www.outflux.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Dave Airlie [Thu, 7 Feb 2013 00:10:04 +0000 (10:10 +1000)]
drm/usb: bind driver to correct device
commit
9f23de52b64f7fb801fd76f3dd8651a0dc89187b upstream.
While looking at plymouth on udl I noticed that plymouth was trying
to use its fb plugin not its drm one, it was trying to drmOpen a driver called
usb not udl, noticed that we actually had out driver pointing at the wrong
device.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Dave Airlie [Thu, 24 Jan 2013 06:12:41 +0000 (16:12 +1000)]
fbcon: don't lose the console font across generic->chip driver switch
commit
ae1287865f5361fa138d4d3b1b6277908b54eac9 upstream.
If grub2 loads efifb/vesafb, then when systemd starts it can set the console
font on that framebuffer device, however when we then load the native KMS
driver, the first thing it does is tear down the generic framebuffer driver.
The thing is the generic code is doing the right thing, it frees the font
because otherwise it would leak memory. However we can assume that if you
are removing the generic firmware driver (vesa/efi/offb), that a new driver
*should* be loading soon after, so we effectively leak the font.
However the old code left a dangling pointer in vc->vc_font.data and we
can now reuse that dangling pointer to load the font into the new
driver, now that we aren't freeing it.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=892340
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Dave Airlie [Thu, 24 Jan 2013 04:14:19 +0000 (14:14 +1000)]
vgacon/vt: clear buffer attributes when we load a 512 character font (v2)
commit
2a2483072393b27f4336ab068a1f48ca19ff1c1e upstream.
When we switch from 256->512 byte font rendering mode, it means the
current contents of the screen is being reinterpreted. The bit that holds
the high bit of the 9-bit font, may have been previously set, and thus
the new font misrenders.
The problem case we see is grub2 writes spaces with the bit set, so it
ends up with data like 0x820, which gets reinterpreted into 0x120 char
which the font translates into G with a circumflex. This flashes up on
screen at boot and is quite ugly.
A current side effect of this patch though is that any rendering on the
screen changes color to a slightly darker color, but at least the screen
no longer corrupts.
v2: as suggested by hpa, always clear the attribute space, whether we
are are going to or from 512 chars.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Joseph Salisbury [Tue, 5 Feb 2013 00:16:29 +0000 (00:16 +0000)]
ACPI: Add DMI entry for Sony VGN-FW41E_H
commit
66f2fda93b67fa744d406e6dcf443f67bac204b6 upstream.
This patch adds a quirk to allow the Sony VGN-FW41E_H to suspend/resume
properly.
References: http://bugs.launchpad.net/bugs/1113547
Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Ian Abbott [Wed, 27 Feb 2013 10:56:19 +0000 (10:56 +0000)]
staging: comedi: check s->async for poll(), read() and write()
commit
cc400e185c07c15a42d2635995f422de5b94b696 upstream.
Some low-level comedi drivers (incorrectly) point `dev->read_subdev` or
`dev->write_subdev` to a subdevice that does not support asynchronous
commands. Comedi's poll(), read() and write() file operation handlers
assume these subdevices do support asynchronous commands. In
particular, they assume `s->async` is valid (where `s` points to the
read or write subdevice), which it won't be if it has been set
incorrectly. This can lead to a NULL pointer dereference.
Check `s->async` is non-NULL in `comedi_poll()`, `comedi_read()` and
`comedi_write()` to avoid the bug.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
majianpeng [Tue, 29 Jan 2013 05:16:06 +0000 (13:16 +0800)]
nfsd: Fix memleak
commit
2d32b29a1c2830f7c42caa8258c714acd983961f upstream.
When free nfs-client, it must free the ->cl_stateids.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Leonid Shatz [Mon, 4 Feb 2013 12:33:37 +0000 (14:33 +0200)]
hrtimer: Prevent hrtimer_enqueue_reprogram race
commit
b22affe0aef429d657bc6505aacb1c569340ddd2 upstream.
hrtimer_enqueue_reprogram contains a race which could result in
timer.base switch during unlock/lock sequence.
hrtimer_enqueue_reprogram is releasing the lock protecting the timer
base for calling raise_softirq_irqsoff() due to a lock ordering issue
versus rq->lock.
If during that time another CPU calls __hrtimer_start_range_ns() on
the same hrtimer, the timer base might switch, before the current CPU
can lock base->lock again and therefor the unlock_timer_base() call
will unlock the wrong lock.
[ tglx: Added comment and massaged changelog ]
Signed-off-by: Leonid Shatz <leonid.shatz@ravellosystems.com>
Signed-off-by: Izik Eidus <izik.eidus@ravellosystems.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Link: http://lkml.kernel.org/r/1359981217-389-1-git-send-email-izik.eidus@ravellosystems.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Oleg Nesterov [Tue, 29 Jan 2013 19:07:41 +0000 (20:07 +0100)]
tty: set_termios/set_termiox should not return -EINTR
commit
183d95cdd834381c594d3aa801c1f9f9c0c54fa9 upstream.
See https://bugzilla.redhat.com/show_bug.cgi?id=904907
read command causes bash to abort with double free or corruption (out).
A simple test-case from Roman:
// Compile the reproducer and send sigchld ti that process.
// EINTR occurs even if SA_RESTART flag is set.
void handler(int sig)
{
}
main()
{
struct sigaction act;
act.sa_handler = handler;
act.sa_flags = SA_RESTART;
sigaction (SIGCHLD, &act, 0);
struct termio ttp;
ioctl(0, TCGETA, &ttp);
while(1)
{
if (ioctl(0, TCSETAW, ttp) < 0)
{
if (errno == EINTR)
{
fprintf(stderr, "BUG!"); return(1);
}
}
}
}
Change set_termios/set_termiox to return -ERESTARTSYS to fix this
particular problem.
I didn't dare to change other EINTR's in drivers/tty/, but they look
equally wrong.
Reported-by: Roman Rakus <rrakus@redhat.com>
Reported-by: Lingzhu Xiang <lxiang@redhat.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Adam Thomas [Sat, 2 Feb 2013 22:35:08 +0000 (22:35 +0000)]
UBIFS: fix double free of ubifs_orphan objects
commit
8afd500cb52a5d00bab4525dd5a560d199f979b9 upstream.
The last orphan in the dnext list has its dnext set to NULL. Because
of that, ubifs_delete_orphan assumes that it is not on the dnext list
and frees it immediately instead ignoring it as a second delete. The
orphan is later freed again by erase_deleted.
This change adds an explicit flag to ubifs_orphan indicating whether
it is pending delete.
Signed-off-by: Adam Thomas <adamthomas1111@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Takashi Iwai [Mon, 4 Feb 2013 09:28:15 +0000 (10:28 +0100)]
ALSA: aloop: Fix Oops while PM resume
commit
edac894389f9c9de2a1368c78809c824b343f3a5 upstream.
snd-aloop driver has no proper PM implementation, thus the PM resume
may trigger Oops due to leftover timer instance. This patch adds the
missing suspend/resume implementation.
Reported-and-tested-by: El boulangero <elboulangero@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Bjorn Helgaas [Tue, 29 Jan 2013 23:44:27 +0000 (16:44 -0700)]
Driver core: treat unregistered bus_types as having no devices
commit
4fa3e78be7e985ca814ce2aa0c09cbee404efcf7 upstream.
A bus_type has a list of devices (klist_devices), but the list and the
subsys_private structure that contains it are not initialized until the
bus_type is registered with bus_register().
The panic/reboot path has fixups that look up devices in pci_bus_type. If
we panic before registering pci_bus_type, the bus_type exists but the list
does not, so mach_reboot_fixups() trips over a null pointer and panics
again:
mach_reboot_fixups
pci_get_device
..
bus_find_device(&pci_bus_type, ...)
bus->p is NULL
Joonsoo reported a problem when panicking before PCI was initialized.
I think this patch should be sufficient to replace the patch he posted
here: https://lkml.org/lkml/2012/12/28/75 ("[PATCH] x86, reboot: skip
reboot_fixups in early boot phase")
Reported-by: Joonsoo Kim <js1304@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Minchan Kim [Wed, 30 Jan 2013 02:41:39 +0000 (11:41 +0900)]
zram: Fix deadlock bug in partial read/write
commit
7e5a5104c6af709a8d97d5f4711e7c917761d464 upstream.
Now zram allocates new page with GFP_KERNEL in zram I/O path
if IO is partial. Unfortunately, It may cause deadlock with
reclaim path like below.
write_page from fs
fs_lock
allocation(GFP_KERNEL)
reclaim
pageout
write_page from fs
fs_lock <-- deadlock
This patch fixes it by using GFP_NOIO. In read path, we
reorganize code flow so that kmap_atomic is called after the
GFP_NOIO allocation.
Acked-by: Jerome Marchand <jmarchand@redhat.com>
Acked-by: Nitin Gupta <ngupta@vflare.org>
[ penberg@kernel.org: don't use GFP_ATOMIC ]
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: no reordering is needed in the read path]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Niu Yawei [Sat, 2 Feb 2013 02:31:27 +0000 (21:31 -0500)]
ext4: fix race in ext4_mb_add_n_trim()
commit
f1167009711032b0d747ec89a632a626c901a1ad upstream.
In ext4_mb_add_n_trim(), lg_prealloc_lock should be taken when
changing the lg_prealloc_list.
Signed-off-by: Niu Yawei <yawei.niu@intel.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Takashi Iwai [Fri, 1 Feb 2013 13:01:27 +0000 (14:01 +0100)]
ALSA: hda - Release assigned pin/cvt at error path of hdmi_pcm_open()
commit
2ad779b7329d6894a80df94e693e72eaa0d56790 upstream.
If the driver detects and invalid ELD, it gives an open error.
But it forgot to release the assigned pin, converter and spdif ctls
before returning.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Dave Hansen [Thu, 31 Jan 2013 00:56:16 +0000 (16:56 -0800)]
x86-32, mm: Rip out x86_32 NUMA remapping code
commit
f03574f2d5b2d6229dcdf2d322848065f72953c7 upstream.
This code was an optimization for 32-bit NUMA systems.
It has probably been the cause of a number of subtle bugs over
the years, although the conditions to excite them would have
been hard to trigger. Essentially, we remap part of the kernel
linear mapping area, and then sometimes part of that area gets
freed back in to the bootmem allocator. If those pages get
used by kernel data structures (say mem_map[] or a dentry),
there's no big deal. But, if anyone ever tried to use the
linear mapping for these pages _and_ cared about their physical
address, bad things happen.
For instance, say you passed __GFP_ZERO to the page allocator
and then happened to get handed one of these pages, it zero the
remapped page, but it would make a pte to the _old_ page.
There are probably a hundred other ways that it could screw
with things.
We don't need to hang on to performance optimizations for
these old boxes any more. All my 32-bit NUMA systems are long
dead and buried, and I probably had access to more than most
people.
This code is causing real things to break today:
https://lkml.org/lkml/2013/1/9/376
I looked in to actually fixing this, but it requires surgery
to way too much brittle code, as well as stuff like
per_cpu_ptr_to_phys().
[ hpa: Cc: this for -stable, since it is a memory corruption issue.
However, an alternative is to simply mark NUMA as depends BROKEN
rather than EXPERIMENTAL in the X86_32 subclause... ]
Link: http://lkml.kernel.org/r/20130131005616.1C79F411@kernel.stglabs.ibm.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
[bwh: For 3.2, using the suggested alternative]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Clemens Ladisch [Thu, 31 Jan 2013 20:14:33 +0000 (21:14 +0100)]
ALSA: usb-audio: fix Roland A-PRO support
commit
7da58046482fceb17c4a0d4afefd9507ec56de7f upstream.
The quirk for the Roland/Cakewalk A-PRO keyboards accidentally used the
wrong interface number, which prevented the driver from attaching to the
device.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Ian Abbott [Mon, 28 Jan 2013 16:14:31 +0000 (16:14 +0000)]
staging: comedi: disallow COMEDI_DEVCONFIG on non-board minors
commit
754ab5c0e55dd118273ca2c217c4d95e9fbc8259 upstream.
Comedi has two sorts of minor devices:
(a) normal board minor devices in the range 0 to
COMEDI_NUM_BOARD_MINORS-1 inclusive; and
(b) special subdevice minor devices in the range COMEDI_NUM_BOARD_MINORS
upwards that are used to open the same underlying comedi device as the
normal board minor devices, but with non-default read and write
subdevices for asynchronous commands.
The special subdevice minor devices get created when a board supporting
asynchronous commands is attached to a normal board minor device, and
destroyed when the board is detached from the normal board minor device.
One way to attach or detach a board is by using the COMEDI_DEVCONFIG
ioctl. This should only be used on normal board minors as the special
subdevice minors are too ephemeral. In particular, the change
introduced in commit
7d3135af399e92cf4c9bbc5f86b6c140aab3b88c ("staging:
comedi: prevent auto-unconfig of manually configured devices") breaks
horribly for special subdevice minor devices.
Since there's no legitimate use for the COMEDI_DEVCONFIG ioctl on a
special subdevice minor device node, disallow it and return -ENOTTY.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Christian Borntraeger [Fri, 25 Jan 2013 14:34:15 +0000 (15:34 +0100)]
s390/kvm: Fix store status for ACRS/FPRS
commit
15bc8d8457875f495c59d933b05770ba88d1eacb upstream.
On store status we need to copy the current state of registers
into a save area. Currently we might save stale versions:
The sie state descriptor doesnt have fields for guest ACRS,FPRS,
those registers are simply stored in the host registers. The host
program must copy these away if needed. We do that in vcpu_put/load.
If we now do a store status in KVM code between vcpu_put/load, the
saved values are not up-to-date. Lets collect the ACRS/FPRS before
saving them.
This also fixes some strange problems with hotplug and virtio-ccw,
since the low level machine check handler (on hotplug a machine check
will happen) will revalidate all registers with the content of the
save area.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
[bwh: Backported to 3.2 as done in 3.0 by Jiri Slaby]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Jiri Slaby <jslaby@suse.cz>
Jan Kara [Wed, 30 Jan 2013 03:48:17 +0000 (22:48 -0500)]
ext4: fix possible use-after-free with AIO
commit
091e26dfc156aeb3b73bc5c5f277e433ad39331c upstream.
Running AIO is pinning inode in memory using file reference. Once AIO
is completed using aio_complete(), file reference is put and inode can
be freed from memory. So we have to be sure that calling aio_complete()
is the last thing we do with the inode.
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Theodore Ts'o [Fri, 25 Jan 2013 04:24:56 +0000 (23:24 -0500)]
quota: autoload the quota_v2 module for QFMT_VFS_V1 quota format
commit
c3ad83d9efdfe6a86efd44945a781f00c879b7b4 upstream.
Otherwise, ext4 file systems with the quota featured enable will get a
very confusing "No such process" error message if the quota code is
built as a module and the quota_v2 module has not been loaded.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Bjørn Mork [Wed, 23 Jan 2013 09:44:36 +0000 (10:44 +0100)]
USB: option: add and update Alcatel modems
commit
f8f0302bbcbd1b14655bef29f6996a2152be559d upstream.
Adding three currently unsupported modems based on information
from .inf driver files:
Diag VID_1BBB&PID_0052&MI_00
AGPS VID_1BBB&PID_0052&MI_01
VOICE VID_1BBB&PID_0052&MI_02
AT VID_1BBB&PID_0052&MI_03
Modem VID_1BBB&PID_0052&MI_05
wwan VID_1BBB&PID_0052&MI_06
Diag VID_1BBB&PID_00B6&MI_00
AT VID_1BBB&PID_00B6&MI_01
Modem VID_1BBB&PID_00B6&MI_02
wwan VID_1BBB&PID_00B6&MI_03
Diag VID_1BBB&PID_00B7&MI_00
AGPS VID_1BBB&PID_00B7&MI_01
VOICE VID_1BBB&PID_00B7&MI_02
AT VID_1BBB&PID_00B7&MI_03
Modem VID_1BBB&PID_00B7&MI_04
wwan VID_1BBB&PID_00B7&MI_05
Updating the blacklist info for the X060S_X200 and X220_X500D,
reserving interfaces for a wwan driver, based on
wwan VID_1BBB&PID_0000&MI_04
wwan VID_1BBB&PID_0017&MI_06
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Igor Grinberg [Sun, 13 Jan 2013 11:49:47 +0000 (13:49 +0200)]
ARM: PXA3xx: program the CSMSADRCFG register
commit
d107a204154ddd79339203c2deeb7433f0cf6777 upstream.
The Chip Select Configuration Register must be programmed to 0x2 in
order to achieve the correct behavior of the Static Memory Controller.
Without this patch devices wired to DFI and accessed through SMC cannot
be accessed after resume from S2.
Do not rely on the boot loader to program the CSMSADRCFG register by
programming it in the kernel smemc module.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
John David Anglin [Tue, 15 Jan 2013 00:45:00 +0000 (19:45 -0500)]
Purge existing TLB entries in set_pte_at and ptep_set_wrprotect
commit
7139bc1579901b53db7e898789e916ee2fb52d78 upstream.
This patch goes a long way toward fixing the minifail bug, and
it significantly improves the stability of SMP machines such as
the rp3440. When write protecting a page for COW, we need to
purge the existing translation. Otherwise, the COW break
doesn't occur as expected because the TLB may still have a stale entry
which allows writes.
[jejb: fix up checkpatch errors]
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Jean Delvare [Sun, 16 Dec 2012 21:00:50 +0000 (22:00 +0100)]
pcmcia/vrc4171: Add missing spinlock init
commit
811af9723859884f2f771f3174f3ddedab7c53b5 upstream.
It doesn't seem this spinlock was properly initialized. This bug was
introduced by commit
7a410e8d4d97457c8c381e2de9cdc7bd3306badc.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Theodore Ts'o [Sat, 12 Jan 2013 21:19:36 +0000 (16:19 -0500)]
ext4: return ENOMEM if sb_getblk() fails
commit
860d21e2c585f7ee8a4ecc06f474fdc33c9474f4 upstream.
The only reason for sb_getblk() failing is if it can't allocate the
buffer_head. So ENOMEM is more appropriate than EIO. In addition,
make sure that the file system is marked as being inconsistent if
sb_getblk() fails.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
[bwh: Backported to 3.2:
- Adjust context
- Drop change to inline.c
- Call to ext4_ext_check() from ext4_ext_find_extent() is conditional]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Thadeu Lima de Souza Cascardo [Fri, 28 Dec 2012 09:13:19 +0000 (09:13 +0000)]
powerpc/eeh: Fix crash when adding a device in a slot with DDW
commit
6a040ce72598159a74969a2d01ab0ba5ee6536b3 upstream.
The DDW code uses a eeh_dev struct from the pci_dev. However, this is
not set until eeh_add_device_late is called.
Since pci_bus_add_devices is called before eeh_add_device_late, the PCI
devices are added to the bus, making drivers' probe hooks to be called.
These will call set_dma_mask, which will call the DDW code, which will
require the eeh_dev struct from pci_dev. This would result in a crash,
due to a NULL dereference.
Calling eeh_add_device_late after pci_bus_add_devices would make the
system BUG, because device files shouldn't be added to devices there
were not added to the system. So, a new function is needed to add such
files only after pci_bus_add_devices have been called.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Acked-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Maciej Sosnowski [Wed, 23 May 2012 15:27:07 +0000 (17:27 +0200)]
dca: check against empty dca_domains list before unregister provider
commit
c419fcfd071cf34ba00f9f65282583772d2655e7 upstream.
When providers get blocked unregister_dca_providers() is called ending up
with dca_providers and dca_domain lists emptied. Dca should be prevented from
trying to unregister any provider if dca_domain list is found empty.
Reported-by: Jiang Liu <jiang.liu@huawei.com>
Tested-by: Gaohuai Han <hangaohuai@huawei.com>
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <djbw@fb.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Al Viro [Sun, 16 Dec 2012 19:04:46 +0000 (16:04 -0300)]
omap_vout: find_vma() needs ->mmap_sem held
commit
55ee64b30a38d688232e5eb2860467dddc493573 upstream.
Walking rbtree while it's modified is a Bad Idea(tm); besides,
the result of find_vma() can be freed just as it's getting returned
to caller. Fortunately, it's easy to fix - just take ->mmap_sem a bit
earlier (and don't bother with find_vma() at all if virtp >= PAGE_OFFSET -
in that case we don't even look at its result).
While we are at it, what prevents VIDIOC_PREPARE_BUF calling
v4l_prepare_buf() -> (e.g) vb2_ioctl_prepare_buf() -> vb2_prepare_buf() ->
__buf_prepare() -> __qbuf_userptr() -> vb2_vmalloc_get_userptr() -> find_vma(),
AFAICS without having taken ->mmap_sem anywhere in process? The code flow
is bloody convoluted and depends on a bunch of things done by initialization,
so I certainly might've missed something...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Archit Taneja <archit@ti.com>
Cc: Prabhakar Lad <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[bwh: Backported to 3.2: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Laurent Pinchart [Sun, 25 Nov 2012 00:35:48 +0000 (21:35 -0300)]
v4l: Reset subdev v4l2_dev field to NULL if registration fails
commit
317efce991620adc589b3005b9baed433dcb2a56 upstream.
When subdev registration fails the subdev v4l2_dev field is left to a
non-NULL value. Later calls to v4l2_device_unregister_subdev() will
consider the subdev as registered and will module_put() the subdev
module without any matching module_get().
Fix this by setting the subdev v4l2_dev field to NULL in
v4l2_device_register_subdev() when the function fails.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[bwh: Backported to 3.2: adjust context, filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tejun Heo [Tue, 18 Dec 2012 18:35:02 +0000 (10:35 -0800)]
workqueue: consider work function when searching for busy work items
commit
a2c1c57be8d9fd5b716113c8991d3d702eeacf77 upstream.
To avoid executing the same work item concurrenlty, workqueue hashes
currently busy workers according to their current work items and looks
up the the table when it wants to execute a new work item. If there
already is a worker which is executing the new work item, the new item
is queued to the found worker so that it gets executed only after the
current execution finishes.
Unfortunately, a work item may be freed while being executed and thus
recycled for different purposes. If it gets recycled for a different
work item and queued while the previous execution is still in
progress, workqueue may make the new work item wait for the old one
although the two aren't really related in any way.
In extreme cases, this false dependency may lead to deadlock although
it's extremely unlikely given that there aren't too many self-freeing
work item users and they usually don't wait for other work items.
To alleviate the problem, record the current work function in each
busy worker and match it together with the work item address in
find_worker_executing_work(). While this isn't complete, it ensures
that unrelated work items don't interact with each other and in the
very unlikely case where a twisted wq user triggers it, it's always
onto itself making the culprit easy to spot.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Andrey Isakov <andy51@gmx.ru>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=51701
[bwh: Backported to 3.2:
- Adjust context
- Incorporate earlier logging cleanup in process_one_work() from
044c782ce3a9 ('workqueue: fix checkpatch issues')]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cornelia Huck [Fri, 14 Dec 2012 16:02:16 +0000 (17:02 +0100)]
KVM: s390: Handle hosts not supporting s390-virtio.
commit
55c171a6d90dc0574021f9c836127cfd1a7d2e30 upstream.
Running under a kvm host does not necessarily imply the presence of
a page mapped above the main memory with the virtio information;
however, the code includes a hard coded access to that page.
Instead, check for the presence of the page and exit gracefully
before we hit an addressing exception if it does not exist.
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Thomas Gleixner [Fri, 23 Nov 2012 09:08:44 +0000 (10:08 +0100)]
genirq: Avoid deadlock in spurious handling
commit
e716efde75267eab919cdb2bef5b2cb77f305326 upstream.
commit
52553ddf(genirq: fix regression in irqfixup, irqpoll)
introduced a potential deadlock by calling the action handler with the
irq descriptor lock held.
Remove the call and let the handling code run even for an interrupt
where only a single action is registered. That matches the goal of
the above commit and avoids the deadlock.
Document the confusing action = desc->action reload in the handling
loop while at it.
Reported-and-tested-by: "Wang, Warner" <warner.wang@hp.com>
Tested-by: Edward Donovan <edward.donovan@numble.net>
Cc: "Wang, Song-Bo (Stoney)" <song-bo.wang@hp.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
David S. Miller [Thu, 14 Feb 2013 19:49:01 +0000 (11:49 -0800)]
sunvdc: Fix off-by-one in generic_request().
[ Upstream commit
f4d9605434c0fd4cc8639bf25cfc043418c52362 ]
The 'operations' bitmap corresponds one-for-one with the operation
codes, no adjustment is necessary.
Reported-by: Mark Kettenis <mark.kettenis@xs4all.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Ben Hutchings [Wed, 20 Feb 2013 03:15:40 +0000 (03:15 +0000)]
Linux 3.2.39
Jan Beulich [Thu, 24 Jan 2013 13:11:10 +0000 (13:11 +0000)]
x86/xen: don't assume %ds is usable in xen_iret for 32-bit PVOPS.
commit
13d2b4d11d69a92574a55bfd985cfb0ca77aebdc upstream.
This fixes CVE-2013-0228 / XSA-42
Drew Jones while working on CVE-2013-0190 found that that unprivileged guest user
in 32bit PV guest can use to crash the > guest with the panic like this:
-------------
general protection fault: 0000 [#1] SMP
last sysfs file: /sys/devices/vbd-51712/block/xvda/dev
Modules linked in: sunrpc ipt_REJECT nf_conntrack_ipv4 nf_defrag_ipv4
iptable_filter ip_tables ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6
xt_state nf_conntrack ip6table_filter ip6_tables ipv6 xen_netfront ext4
mbcache jbd2 xen_blkfront dm_mirror dm_region_hash dm_log dm_mod [last
unloaded: scsi_wait_scan]
Pid: 1250, comm: r Not tainted 2.6.32-356.el6.i686 #1
EIP: 0061:[<
c0407462>] EFLAGS:
00010086 CPU: 0
EIP is at xen_iret+0x12/0x2b
EAX:
eb8d0000 EBX:
00000001 ECX:
08049860 EDX:
00000010
ESI:
00000000 EDI:
003d0f00 EBP:
b77f8388 ESP:
eb8d1fe0
DS: 0000 ES: 007b FS: 0000 GS: 00e0 SS: 0069
Process r (pid: 1250, ti=
eb8d0000 task=
c2953550 task.ti=
eb8d0000)
Stack:
00000000 0027f416 00000073 00000206 b77f8364 0000007b 00000000 00000000
Call Trace:
Code: c3 8b 44 24 18 81 4c 24 38 00 02 00 00 8d 64 24 30 e9 03 00 00 00
8d 76 00 f7 44 24 08 00 00 02 80 75 33 50 b8 00 e0 ff ff 21 e0 <8b> 40
10 8b 04 85 a0 f6 ab c0 8b 80 0c b0 b3 c0 f6 44 24 0d 02
EIP: [<
c0407462>] xen_iret+0x12/0x2b SS:ESP 0069:
eb8d1fe0
general protection fault: 0000 [#2]
---[ end trace
ab0d29a492dcd330 ]---
Kernel panic - not syncing: Fatal exception
Pid: 1250, comm: r Tainted: G D ---------------
2.6.32-356.el6.i686 #1
Call Trace:
[<
c08476df>] ? panic+0x6e/0x122
[<
c084b63c>] ? oops_end+0xbc/0xd0
[<
c084b260>] ? do_general_protection+0x0/0x210
[<
c084a9b7>] ? error_code+0x73/
-------------
Petr says: "
I've analysed the bug and I think that xen_iret() cannot cope with
mangled DS, in this case zeroed out (null selector/descriptor) by either
xen_failsafe_callback() or RESTORE_REGS because the corresponding LDT
entry was invalidated by the reproducer. "
Jan took a look at the preliminary patch and came up a fix that solves
this problem:
"This code gets called after all registers other than those handled by
IRET got already restored, hence a null selector in %ds or a non-null
one that got loaded from a code or read-only data descriptor would
cause a kernel mode fault (with the potential of crashing the kernel
as a whole, if panic_on_oops is set)."
The way to fix this is to realize that the we can only relay on the
registers that IRET restores. The two that are guaranteed are the
%cs and %ss as they are always fixed GDT selectors. Also they are
inaccessible from user mode - so they cannot be altered. This is
the approach taken in this patch.
Another alternative option suggested by Jan would be to relay on
the subtle realization that using the %ebp or %esp relative references uses
the %ss segment. In which case we could switch from using %eax to %ebp and
would not need the %ss over-rides. That would also require one extra
instruction to compensate for the one place where the register is used
as scaled index. However Andrew pointed out that is too subtle and if
further work was to be done in this code-path it could escape folks attention
and lead to accidents.
Reviewed-by: Petr Matousek <pmatouse@redhat.com>
Reported-by: Petr Matousek <pmatouse@redhat.com>
Reviewed-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Nithin Nayak Sujir [Mon, 14 Jan 2013 17:11:00 +0000 (17:11 +0000)]
tg3: Fix crc errors on jumbo frame receive
[ Upstream commit
daf3ec688e057f6060fb9bb0819feac7a8bbf45c ]
TG3_PHY_AUXCTL_SMDSP_ENABLE/DISABLE macros do a blind write to the phy
auxiliary control register and overwrite the EXT_PKT_LEN (bit 14) resulting
in intermittent crc errors on jumbo frames with some link partners. Change
the code to do a read/modify/write.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Nithin Nayak Sujir [Mon, 14 Jan 2013 17:10:59 +0000 (17:10 +0000)]
tg3: Avoid null pointer dereference in tg3_interrupt in netconsole mode
[ Upstream commit
9c13cb8bb477a83b9a3c9e5a5478a4e21294a760 ]
When netconsole is enabled, logging messages generated during tg3_open
can result in a null pointer dereference for the uninitialized tg3
status block. Use the irq_sync flag to disable polling in the early
stages. irq_sync is cleared when the driver is enabling interrupts after
all initialization is completed.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Sarveshwar Bandi [Wed, 10 Oct 2012 01:15:01 +0000 (01:15 +0000)]
bridge: Pull ip header into skb->data before looking into ip header.
[ Upstream commit
6caab7b0544e83e6c160b5e80f5a4a7dd69545c7 ]
If lower layer driver leaves the ip header in the skb fragment, it needs to
be first pulled into skb->data before inspecting ip header length or ip version
number.
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Eric Dumazet [Sun, 6 Jan 2013 18:21:49 +0000 (18:21 +0000)]
tcp: fix MSG_SENDPAGE_NOTLAST logic
[ Upstream commit
ae62ca7b03217be5e74759dc6d7698c95df498b3 ]
commit
35f9c09fe9c72e (tcp: tcp_sendpages() should call tcp_push() once)
added an internal flag : MSG_SENDPAGE_NOTLAST meant to be set on all
frags but the last one for a splice() call.
The condition used to set the flag in pipe_to_sendpage() relied on
splice() user passing the exact number of bytes present in the pipe,
or a smaller one.
But some programs pass an arbitrary high value, and the test fails.
The effect of this bug is a lack of tcp_push() at the end of a
splice(pipe -> socket) call, and possibly very slow or erratic TCP
sessions.
We should both test sd->total_len and fact that another fragment
is in the pipe (pipe->nrbufs > 1)
Many thanks to Willy for providing very clear bug report, bisection
and test programs.
Reported-by: Willy Tarreau <w@1wt.eu>
Bisected-by: Willy Tarreau <w@1wt.eu>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Ilpo Järvinen [Mon, 4 Feb 2013 02:14:25 +0000 (02:14 +0000)]
tcp: fix for zero packets_in_flight was too broad
[ Upstream commit
6731d2095bd4aef18027c72ef845ab1087c3ba63 ]
There are transients during normal FRTO procedure during which
the packets_in_flight can go to zero between write_queue state
updates and firing the resulting segments out. As FRTO processing
occurs during that window the check must be more precise to
not match "spuriously" :-). More specificly, e.g., when
packets_in_flight is zero but FLAG_DATA_ACKED is true the problematic
branch that set cwnd into zero would not be taken and new segments
might be sent out later.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Tested-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Eric Dumazet [Sun, 3 Feb 2013 09:13:05 +0000 (09:13 +0000)]
tcp: frto should not set snd_cwnd to 0
[ Upstream commit
2e5f421211ff76c17130b4597bc06df4eeead24f ]
Commit
9dc274151a548 (tcp: fix ABC in tcp_slow_start())
uncovered a bug in FRTO code :
tcp_process_frto() is setting snd_cwnd to 0 if the number
of in flight packets is 0.
As Neal pointed out, if no packet is in flight we lost our
chance to disambiguate whether a loss timeout was spurious.
We should assume it was a proper loss.
Reported-by: Pasi Kärkkäinen <pasik@iki.fi>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>