[media] tda9840: fix setting of the audio mode

You have to first detect the current rxsubchans (mono, stereo or bilingual),
and depending on that you can set the audio mode. It does not automatically
switch when the audio channels change.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mxb: simplify a line that was too long

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mxb: fix audio handling

Instead of using custom ioctls use the VIDIOC_ENUM/G/S/_AUDIO ioctls.
Also send the same audio to both CDROM-out and line-out.

This is what you would expect and anyway, the CDROM-out connector is unlikely
to be used these days as it is obsolete.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mxb: fix initial audio + ntsc/secam support

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mxb/saa7146: first round of cleanups

Convert to the control framework, fix the easy v4l2-compliance failures.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l/dvb: fix compiler warnings

media_build/v4l/drxk_hard.c: In function 'DownloadMicrocode':
media_build/v4l/drxk_hard.c:1388:6: warning: variable 'BlockCRC' set but not used [-Wunused-but-set-variable]
media_build/v4l/drxk_hard.c:1384:6: warning: variable 'Drain' set but not used [-Wunused-but-set-variable]
media_build/v4l/drxk_hard.c:1383:6: warning: variable 'Flags' set but not used [-Wunused-but-set-variable]
media_build/v4l/lmedm04.c: In function 'lme2510_probe':
media_build/v4l/lmedm04.c:1208:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/hopper_cards.c: In function 'hopper_irq_handler':
media_build/v4l/hopper_cards.c:68:26: warning: variable 'lstat' set but not used [-Wunused-but-set-variable]
media_build/v4l/mantis_cards.c: In function 'mantis_irq_handler':
media_build/v4l/mantis_cards.c:76:26: warning: variable 'lstat' set but not used [-Wunused-but-set-variable]
media_build/v4l/mantis_dma.c: In function 'mantis_dma_stop':
media_build/v4l/mantis_dma.c:202:16: warning: variable 'mask' set but not used [-Wunused-but-set-variable]
media_build/v4l/mantis_dma.c:202:6: warning: variable 'stat' set but not used [-Wunused-but-set-variable]
media_build/v4l/mantis_evm.c: In function 'mantis_hifevm_work':
media_build/v4l/mantis_evm.c:44:17: warning: variable 'gpif_mask' set but not used [-Wunused-but-set-variable]
media_build/v4l/stb0899_drv.c: In function 'stb0899_init_calc':
media_build/v4l/stb0899_drv.c:640:5: warning: variable 'agc1cn' set but not used [-Wunused-but-set-variable]
media_build/v4l/stb0899_drv.c: In function 'stb0899_diseqc_init':
media_build/v4l/stb0899_drv.c:830:13: warning: variable 'f22_rx' set but not used [-Wunused-but-set-variable]
media_build/v4l/stb0899_drv.c:826:31: warning: variable 'tx_data' set but not used [-Wunused-but-set-variable]
media_build/v4l/stv0900_sw.c: In function 'stv0900_track_optimization':
media_build/v4l/stv0900_sw.c:838:26: warning: variable 'rolloff' set but not used [-Wunused-but-set-variable]
media_build/v4l/ir-sanyo-decoder.c: In function 'ir_sanyo_decode':
media_build/v4l/ir-sanyo-decoder.c:59:14: warning: variable 'not_address' set but not used [-Wunused-but-set-variable]
media_build/v4l/mceusb.c: In function 'mceusb_dev_printdata':
media_build/v4l/mceusb.c:523:46: warning: variable 'data5' set but not used [-Wunused-but-set-variable]

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l/dvb: fix compiler warnings

media_build/v4l/stb6100.c: In function 'stb6100_read_reg':
media_build/v4l/stb6100.c:161:6: warning: variable 'rc' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx24110.c: In function 'cx24110_read_ucblocks':
media_build/v4l/cx24110.c:515:6: warning: variable 'lastbyer' set but not used [-Wunused-but-set-variable]
media_build/v4l/dib9000.c: In function 'dib9000_mbx_process':
media_build/v4l/dib9000.c:711:6: warning: variable 'tmp' set but not used [-Wunused-but-set-variable]
media_build/v4l/zl10353.c: In function 'zl10353_init':
media_build/v4l/zl10353.c:562:6: warning: variable 'rc' set but not used [-Wunused-but-set-variable]
media_build/v4l/stv0297.c: In function 'stv0297_set_frontend':
media_build/v4l/stv0297.c:417:16: warning: variable 'starttime' set but not used [-Wunused-but-set-variable]
media_build/v4l/lgs8gxx.c: In function 'lgs8gxx_set_mode_manual':
media_build/v4l/lgs8gxx.c:265:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/af9013.c: In function 'af9013_statistics_work':
media_build/v4l/af9013.c:517:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/stv090x.c: In function 'stv090x_optimize_track':
media_build/v4l/stv090x.c:2845:23: warning: variable 'rolloff' set but not used [-Wunused-but-set-variable]
media_build/v4l/stv090x.c: In function 'stv090x_algo':
media_build/v4l/stv090x.c:3177:28: warning: variable 'no_signal' set but not used [-Wunused-but-set-variable]
media_build/v4l/it913x-fe.c: In function 'it913x_fe_read_ber':
media_build/v4l/it913x-fe.c:636:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/it913x-fe.c: In function 'it913x_fe_get_frontend':
media_build/v4l/it913x-fe.c:661:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/it913x-fe.c: In function 'it913x_fe_set_frontend':
media_build/v4l/it913x-fe.c:694:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/m88rs2000.c: In function 'm88rs2000_set_fec':
media_build/v4l/m88rs2000.c:657:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/dst_ca.c: In function 'ca_send_message':
media_build/v4l/dst_ca.c:480:15: warning: variable 'ca_message_header_len' set but not used [-Wunused-but-set-variable]
media_build/v4l/smssdio.c: In function 'smssdio_interrupt':
media_build/v4l/smssdio.c:117:11: warning: variable 'isr' set but not used [-Wunused-but-set-variable]

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l: fix compiler warnings

media_build/v4l/adv7343.c: In function 'adv7343_setstd':
media_build/v4l/adv7343.c:133:6: warning: variable 'output_idx' set but not used [-Wunused-but-set-variable]
media_build/v4l/tvp5150.c: In function 'tvp5150_mbus_fmt':
media_build/v4l/tvp5150.c:833:14: warning: variable 'std' set but not used [-Wunused-but-set-variable]
media_build/v4l/tvp7002.c: In function 'tvp7002_query_dv_preset':
media_build/v4l/tvp7002.c:673:18: warning: variable 'device' set but not used [-Wunused-but-set-variable]
media_build/v4l/c-qcam.c: In function 'qc_capture':
media_build/v4l/c-qcam.c:381:33: warning: variable 'bitsperxfer' set but not used [-Wunused-but-set-variable]
media_build/v4l/pms.c: In function 'pms_s_std':
media_build/v4l/pms.c:738:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/pms.c: In function 'init_mediavision':
media_build/v4l/pms.c:959:6: warning: variable 'id' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-alsa.c: In function 'cx25821_irq':
media_build/v4l/cx25821-alsa.c:294:6: warning: variable 'audint_count' set but not used [-Wunused-but-set-variable]
media_build/v4l/zr364xx.c: In function 'zr364xx_fillbuff':
media_build/v4l/zr364xx.c:510:25: warning: variable 'frm' set but not used [-Wunused-but-set-variable]
media_build/v4l/s2255drv.c: In function 's2255_fillbuff':
media_build/v4l/s2255drv.c:637:23: warning: variable 'frm' set but not used [-Wunused-but-set-variable]
media_build/v4l/s2255drv.c: In function 'vidioc_s_fmt_vid_cap':
media_build/v4l/s2255drv.c:990:6: warning: variable 'norm' set but not used [-Wunused-but-set-variable]
media_build/v4l/tm6000-stds.c: In function 'tm6000_set_audio_std':
media_build/v4l/tm6000-stds.c:341:10: warning: variable 'nicam_flag' set but not used [-Wunused-but-set-variable]
media_build/v4l/tm6000-video.c: In function 'get_next_buf':
media_build/v4l/tm6000-video.c:172:8: warning: variable 'outp' set but not used [-Wunused-but-set-variable]
media_build/v4l/tm6000-video.c: In function 'copy_streams':
media_build/v4l/tm6000-video.c:214:36: warning: variable 'c' set but not used [-Wunused-but-set-variable]
media_build/v4l/tm6000-input.c: In function 'tm6000_ir_urb_received':
media_build/v4l/tm6000-input.c:171:6: warning: variable 'rc' set but not used [-Wunused-but-set-variable]
media_build/v4l/usbvision-core.c: In function 'usbvision_decompress':
media_build/v4l/usbvision-core.c:604:23: warning: variable 'max_pos' set but not used [-Wunused-but-set-variable]
media_build/v4l/usbvision-core.c: In function 'usbvision_parse_compress':
media_build/v4l/usbvision-core.c:705:39: warning: variable 'rc' set but not used [-Wunused-but-set-variable]
media_build/v4l/usbvision-core.c:705:22: warning: variable 'bytes_per_pixel' set but not used [-Wunused-but-set-variable]
media_build/v4l/zoran_device.c: In function 'write_overlay_mask':
media_build/v4l/zoran_device.c:545:6: warning: variable 'reg' set but not used [-Wunused-but-set-variable]
media_build/v4l/go7007-v4l2.c: In function 'go7007_streamoff':
media_build/v4l/go7007-v4l2.c:79:6: warning: variable 'retval' set but not used [-Wunused-but-set-variable]

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l: fix compiler warnings

media_build/v4l/au0828-video.c: In function 'au0828_irq_callback':
media_build/v4l/au0828-video.c:123:6: warning: variable 'rc' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx23888-ir.c: In function 'pulse_clocks_to_clock_divider':
media_build/v4l/cx23888-ir.c:334:6: warning: variable 'rem' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25840-ir.c: In function 'pulse_clocks_to_clock_divider':
media_build/v4l/cx25840-ir.c:319:6: warning: variable 'rem' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25840-ir.c: In function 'cx25840_ir_tx_write':
media_build/v4l/cx25840-ir.c:863:21: warning: variable 'c' set but not used [-Wunused-but-set-variable]
media_build/v4l/em28xx-audio.c: In function 'snd_em28xx_hw_capture_params':
media_build/v4l/em28xx-audio.c:346:31: warning: variable 'format' set but not used [-Wunused-but-set-variable]
media_build/v4l/em28xx-audio.c:346:25: warning: variable 'rate' set but not used [-Wunused-but-set-variable]
media_build/v4l/em28xx-audio.c:346:15: warning: variable 'channels' set but not used [-Wunused-but-set-variable]
media_build/v4l/hdpvr-control.c: In function 'get_input_lines_info':
media_build/v4l/hdpvr-control.c:98:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/hdpvr-video.c: In function 'hdpvr_try_ctrl':
media_build/v4l/hdpvr-video.c:955:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/saa7134-video.c: In function 'saa7134_s_tuner':
media_build/v4l/saa7134-video.c:2030:6: warning: variable 'rx' set but not used [-Wunused-but-set-variable]
media_build/v4l/sn9c102_core.c: In function 'sn9c102_stream_interrupt':
media_build/v4l/sn9c102_core.c:998:7: warning: variable 'timeout' set but not used [-Wunused-but-set-variable]

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Janne Grunau <j@jannau.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] cx25821: fix compiler warnings

media_build/v4l/cx25821-core.c: In function 'cx_i2c_read_print':
media_build/v4l/cx25821-core.c:386:6: warning: variable 'value' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-core.c: In function 'cx25821_dev_setup':
media_build/v4l/cx25821-core.c:899:6: warning: variable 'io_size' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-core.c: In function 'cx25821_irq':
media_build/v4l/cx25821-core.c:1321:18: warning: variable 'pci_mask' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-i2c.c: In function 'cx25821_i2c_read':
media_build/v4l/cx25821-i2c.c:365:6: warning: variable 'retval' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-medusa-video.c: In function 'medusa_enable_bluefield_output':
media_build/v4l/cx25821-medusa-video.c:39:6: warning: variable 'ret_val' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-medusa-video.c: In function 'medusa_set_resolution':
media_build/v4l/cx25821-medusa-video.c:435:6: warning: variable 'ret_val' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-medusa-video.c: In function 'medusa_set_decoderduration':
media_build/v4l/cx25821-medusa-video.c:498:6: warning: variable 'ret_val' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-video.c: In function 'cx25821_dump_video_queue':
media_build/v4l/cx25821-video.c:116:25: warning: variable 'buf' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-video.c: In function 'cx25821_buffer_prepare':
media_build/v4l/cx25821-video.c:561:20: warning: variable 'line1_offset' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-video.c: In function 'video_ioctl_set':
media_build/v4l/cx25821-video.c:1834:6: warning: variable 'value' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-video-upstream.c: In function 'cx25821_upstream_irq':
media_build/v4l/cx25821-video-upstream.c:641:6: warning: variable 'msk_stat' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-video-upstream-ch2.c: In function 'cx25821_upstream_irq_ch2':
media_build/v4l/cx25821-video-upstream-ch2.c:591:6: warning: variable 'msk_stat' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-audio-upstream.c: In function 'cx25821_upstream_irq_audio':
media_build/v4l/cx25821-audio-upstream.c:589:6: warning: variable 'msk_stat' set but not used [-Wunused-but-set-variable]

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ivtv/cx18: fix compiler warnings

media_build/v4l/cx18-alsa-main.c: In function 'cx18_alsa_exit':
media_build/v4l/cx18-alsa-main.c:282:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx18-mailbox.c: In function 'cx18_api_call':
media_build/v4l/cx18-mailbox.c:598:6: warning: variable 'state' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx18-alsa-pcm.c: In function 'snd_cx18_pcm_capture_open':
media_build/v4l/cx18-alsa-pcm.c:156:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx18-alsa-pcm.c: In function 'snd_cx18_pcm_capture_close':
media_build/v4l/cx18-alsa-pcm.c:202:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx18-alsa-pcm.c: In function 'snd_cx18_pcm_hw_params':
media_build/v4l/cx18-alsa-pcm.c:255:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx18-streams.c: In function 'cx18_stop_v4l2_encode_stream':
media_build/v4l/cx18-streams.c:983:16: warning: variable 'then' set but not used [-Wunused-but-set-variable]
media_build/v4l/ivtv-ioctl.c: In function 'ivtv_set_speed':
media_build/v4l/ivtv-ioctl.c:138:22: warning: variable 's' set but not used [-Wunused-but-set-variable]
media_build/v4l/ivtvfb.c: In function 'ivtvfb_init':
media_build/v4l/ivtvfb.c:1286:6: warning: variable 'err' set but not used [-Wunused-but-set-variable]
media_build/v4l/ivtvfb.c: In function 'ivtvfb_cleanup':
media_build/v4l/ivtvfb.c:1306:6: warning: variable 'err' set but not used [-Wunused-but-set-variable]

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] cx231xx: fix compiler warnings

v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-audio.c: In function ‘snd_cx231xx_hw_capture_params’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-audio.c:527:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-audio.c:526:31: warning: variable ‘format’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-audio.c:526:25: warning: variable ‘rate’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-audio.c:526:15: warning: variable ‘channels’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-audio.c: In function ‘snd_cx231xx_capture_trigger’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-audio.c:589:6: warning: variable ‘retval’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-video.c: In function ‘cx231xx_isoc_copy’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-video.c:331:17: warning: variable ‘outp’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-video.c: In function ‘cx231xx_bulk_copy’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-video.c:434:17: warning: variable ‘outp’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-video.c: In function ‘cx231xx_reset_video_buffer’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-video.c:704:7: warning: variable ‘outp’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c: In function ‘cx231xx_set_mode’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c:699:6: warning: variable ‘errCode’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c: In function ‘cx231xx_ep5_bulkout’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c:763:6: warning: variable ‘errCode’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c: In function ‘cx231xx_isoc_irq_callback’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c:800:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c: In function ‘cx231xx_bulk_irq_callback’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c:846:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c: In function ‘cx231xx_stop_TS1’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c:1234:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c: In function ‘cx231xx_start_TS1’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c:1254:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c: In function ‘cx231xx_enable656’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c:937:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c: In function ‘cx231xx_disable656’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c:955:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c: In function ‘cx231xx_dump_HH_reg’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c:1323:5: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c: In function ‘cx231xx_dump_SC_reg’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c:1358:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c: In function ‘cx231xx_Setup_AFE_for_LowIF’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c:1444:5: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c: In function ‘cx231xx_set_Colibri_For_LowIF’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c:1504:5: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c: In function ‘cx231xx_set_DIF_bandpass’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c:1559:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c: In function ‘cx231xx_gpio_i2c_write’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c:3093:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-417.c: In function ‘cx231xx_initialize_codec’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-417.c:1098:9: warning: variable ‘data’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-417.c: In function ‘vidioc_streamon’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-417.c:1795:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-vbi.c: In function ‘cx231xx_isoc_vbi_copy’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-vbi.c:86:25: warning: variable ‘buf’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-vbi.c: In function ‘cx231xx_irq_vbi_callback’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-vbi.c:313:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dw2102: fix compile warnings

media_build/v4l/dw2102.c:151:13: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/dw2102.c:224:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/dw2102.c:279:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/dw2102.c:352:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/dw2102.c:435:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/dw2102.c:499:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] m5mols: Add 3A lock control

Add control for locking automatic exposure, focus and white balance
adjustments. While at it, tidy up the data structure documentation.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] m5mols: Add JPEG compression quality control

Add JPEG compression quality control for snapshot capture.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] m5mols: Add exposure metering control

This patch adds V4L2_CID_EXPOSURE_METERING control which allows
to select the light metering mode for automatic exposure as one
of the following modes: spot (small area at the frame center),
center weighted and frame averaged.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] m5mols: Add image stabilization control

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] m5mols: Add wide dynamic range control

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] m5mols: Add exposure bias control

Add integer menu control for exposure bias. The control value range is
-2.0 EV to +2.0 EV, in 0.5 EV steps.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] m5mols: Add auto and preset white balance control

Replace the V4L2_CID_AUTO_WHITE_BALANCE control with its extended
version - V4L2_CID_AUTO_N_PRESET_WHITE_BALANCE so the white balance
presets feature is exposed to user land.

Acked-by: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] m5mols: Add ISO sensitivity controls

Add controls for manual/auto ISO sensitivity.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] m5mols: Use proper sensor mode for the controls

The parameters corresponding to the V4L controls can be reconfigured
only in associated M-5MOLS operation mode. Use struct v4l2_ctrl
priv field to assign the working mode to the controls which can be
modified only in certain conditions.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] m5mols: Refactored controls handling

This patch is a prerequisite for the new controls addition. It consolidates
the control handling code, which is moved to m5mols_controls.c and
staticized. The controls initialization is reordered to better reflect
the control clusters and make the diffs smaller when new controls are added.
To make the code easier to follow when more controls is added use separate
set function for each control.

Rewrite the image effect registers handling.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] m5mols: Convert macros to inline functions

Make to_sd and to_m5mols macros static inline functions
for better type safety.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: Add camera auto focus controls

Add following auto focus controls:

 - V4L2_CID_AUTO_FOCUS_START - single-shot auto focus start
 - V4L2_CID_AUTO_FOCUS_STOP -  single-shot auto focus stop
 - V4L2_CID_AUTO_FOCUS_STATUS - automatic focus status
 - V4L2_CID_AUTO_FOCUS_RANGE - automatic focus scan range selection

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: Add camera 3A lock control

The V4L2_CID_3A_LOCK bitmask control allows applications to pause
or resume the automatic exposure, focus and wite balance adjustments.
It can be used, for example, to lock the 3A adjustments right before
a still image is captured, for pre-focus, etc.
The applications can control each of the algorithms independently,
through a corresponding control bit, if driver allows that.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: Add camera scene mode control

Add control for the scene mode feature available in image sensor
with more advanced ISP firmware. The V4L2_CID_SCENE_MODE menu
control allows to select a set of parameters or a specific image
processing and capture control algorithm optimized for common
image capture conditions.

Signed-off-by: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: Add camera exposure metering control

The V4L2_CID_EXPOSURE_METERING control allows to determine
a method used by the camera for measuring the amount of light
available for automatic exposure.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: Add camera ISO sensitivity controls

Add ISO sensitivity and ISO auto/manual controls. The sensitivity
values are related to level of amplification of the analog signal
between image sensor and ADC. These controls allow to support sensors
exposing an interface to accept the ISO values directly.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: Add camera image stabilization control

Add V4L2_CID_IMAGE_STABILIZATION control for the camera image
stabilization feature. This control can be used to enable/disable
image stabilization. It might get converted to a menu control
in future if more options are needed.

Signed-off-by: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: Add camera wide dynamic range control

Add V4L2_CID_WIDE_DYNAMIC_RANGE camera class control for the
camera wide dynamic range (WDR, HDR) feature. This control
can be used to enable/disable wide dynamic range. It might
get converted to a menu control in future if more options
are needed.

Signed-off-by: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: Add an extended camera white balance control

This patch adds V4L2_CID_AUTO_N_PRESET_WHITE_BALANCE control which is
an extended version of the V4L2_CID_AUTO_WHITE_BALANCE control,
including white balance presets. The following presets are defined:

 - V4L2_WHITE_BALANCE_INCANDESCENT,
 - V4L2_WHITE_BALANCE_FLUORESCENT,
 - V4L2_WHITE_BALANCE_FLUORESCENT_H,
 - V4L2_WHITE_BALANCE_HORIZON,
 - V4L2_WHITE_BALANCE_DAYLIGHT,
 - V4L2_WHITE_BALANCE_FLASH,
 - V4L2_WHITE_BALANCE_CLOUDY,
 - V4L2_WHITE_BALANCE_SHADE.

Signed-off-by: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: Add camera exposure bias control

The camera may in some conditions incorrectly determine the exposure,
and a manual automatic exposure correction may be needed. This patch
adds V4L2_CID_AUTO_EXPOSURE_BIAS control which allows to add some
offset in the automatic exposure control loop, to compensate for
frame under- or over-exposure.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: Add helper function for standard integer menu controls

This patch adds v4l2_ctrl_new_int_menu() helper function which can be used
in drivers for creating standard integer menu control with driver-specific
menu item list. It is similar to v4l2_ctrl_new_std_menu(), except it doesn't
have a mask parameter and an additional qmenu parameter allows passing
an array of signed 64-bit integers as the menu item list.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Tested-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: Extend V4L2_CID_COLORFX with more image effects

This patch adds definition of additional color effects:

 - V4L2_COLORFX_AQUA,
 - V4L2_COLORFX_ART_FREEZE,
 - V4L2_COLORFX_SILHOUETTE,
 - V4L2_COLORFX_SOLARIZATION,
 - V4L2_COLORFX_ANTIQUE,
 - V4L2_COLORFX_SET_CBCR.

The new V4L2_COLORFX_CBCR control is added to allow setting
the fixed Cb, Cr values that replace chroma Cb/Cr coefficients
in case of V4L2_COLORFX_SET_CBCR effect.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] radio-si470x-usb: remove autosuspend, implement suspend/resume

The radio-si470x-usb driver supported both autosuspend and it stopped the
radio the moment the last user of the radio device closed it. However, that
was very confusing since if you play the audio from the device (e.g. through
arecord -D ... | aplay) then no sound would play unless you had the radio
device open at the same time, even though there is no need to do anything
with that node.

On the other hand, the actual suspend/resume functions didn't do anything,
which would fail if you *did* have the radio node open at that time.

So:

- remove autosuspend (bad idea in general for USB radio devices)
- move the start/stop out of the open/release functions into the resume/suspend
  functions.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] radio-si470x-common.c: remove unnecessary kernel log spam

There is no need to report an error in the log, you are already returning
that error to userspace after all.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] si470x: add control event support and more v4l2 compliancy fixes

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] si470x: Clean up, introduce the control framework

This cleans up the code and si470x now uses the proper v4l2 frameworks
and passes most of the v4l2-compliance tests.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l: v4l2-ctrls: moves the forward declaration of struct file

This fixes the following warning:

In file included from drivers/media/video/v4l2-subdev.c:29:
include/media/v4l2-ctrls.h:501: warning: 'struct file' declared inside
parameter list
include/media/v4l2-ctrls.h:501: warning: its scope is only this
definition or declaration, which is probably not what you want
include/media/v4l2-ctrls.h:509: warning: 'struct file' declared inside
parameter list

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mt9v032: Correct the logic for the auto-exposure setting

The driver uses the ctrl value passed in as a bool to determine whether
to enable auto-exposure, but the auto-exposure setting is defined as an
enum where AUTO has a value of 0 and MANUAL has a value of 1. This leads
to a reversed logic where if you send in AUTO, it actually sets manual
exposure and vice-versa.

Signed-off-by: Kartik Mohta <kartikmohta@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mt9m032: use the available subdev pointer, don't re-calculate it

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mt9m032: fix compilation breakage

Fix the following compilation failure:

linux-2.6/drivers/media/video/mt9m032.c: In function '__mt9m032_get_pad_crop':
linux-2.6/drivers/media/video/mt9m032.c:337: error: implicit declaration of function 'v4l2_subdev_get_try_crop'
linux-2.6/drivers/media/video/mt9m032.c:337: warning: return makes pointer from integer without a cast
linux-2.6/drivers/media/video/mt9m032.c: In function '__mt9m032_get_pad_format':
linux-2.6/drivers/media/video/mt9m032.c:359: error: implicit declaration of function 'v4l2_subdev_get_try_format'
linux-2.6/drivers/media/video/mt9m032.c:359: warning: return makes pointer from integer without a cast
linux-2.6/drivers/media/video/mt9m032.c: In function 'mt9m032_probe':
linux-2.6/drivers/media/video/mt9m032.c:767: error: 'struct v4l2_subdev' has no member named 'entity'
linux-2.6/drivers/media/video/mt9m032.c:826: error: 'struct v4l2_subdev' has no member named 'entity'
linux-2.6/drivers/media/video/mt9m032.c: In function 'mt9m032_remove':
linux-2.6/drivers/media/video/mt9m032.c:842: error: 'struct v4l2_subdev' has no member named 'entity'
make[4]: *** [drivers/media/video/mt9m032.o] Error 1

by adding a dependency on VIDEO_V4L2_SUBDEV_API.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mt9m032: fix two dead-locks

Fix a copy-paste typo and a nested locking function call in mt9m032.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mt9p031: Implement black level compensation control

Add four new controls to configure black level compensation (BLC):

- V4L2_CID_BLC_AUTO selects between manual and auto BLC
- V4L2_CID_BLC_TARGET_LEVEL sets the target level for auto BLC
- V4L2_CID_BLC_ANALOG_OFFSET sets the analog offset for manual BLC
- V4L2_CID_BLC_DIGITAL_OFFSET sets the digital offset for manual BLC

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mt9p031: Replace the reset board callback by a GPIO number

Use the GPIO from the sensor driver instead of calling back to board
code.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mt9p031: Identify color/mono models using I2C device name

Instead of passing a color/monochrome flag through platform data, rely
on the I2C device name to identify the chip model.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] af9035: add few new reference design USB IDs

Add all known reference design USB IDs.
Rename two earlier reference design USB IDs.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] af9035: remove one config parameter

We can use tuner ID instead of HW not supported flag.
Lesser code is better code.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] af9035: move device configuration to the state

Fixes most problems when having more than one device connected
as demod and tuner configurations are not shared.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] af9033: implement ber and ucb functions

af9033: implement read_ber and read_ucblocks functions. Version 2 of patch that
reflects my findings on the behaviour of abort_cnt, err_cnt and bit_cnt:

- bit_cnt is always 0x2710 (10000)
- abort_cnt is between 0 and 0x2710
- err_cnt is between 0 and 640000 (= 0x2710 * 8 * 8)

in the current implementation BER is calculated as the number of bit errors per
processed bits, ignoring those bits that are already discarded and counted in
abort_cnt, i.e. UCBLOCKS.

Signed-off-by: Hans-Frieder Vogt <hfvogt@gmx.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] af9035: add remote control support

Signed-off-by: Hans-Frieder Vogt <hfvogt@gmx.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] af9035: remove unused struct

Not used anymore since new firmware downloader. I forget to remove
those earlier when changed firmware downloader.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] af9035: various small changes for af9035_ctrl_msg()

Fix USB buffer len to maximum possible.
Various log writing fixes, remove extra new lines and excessive
type casts. Rename and type change some variables.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] pms: update to the latest V4L2 frameworks

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5p-fimc: Fix locking in subdev set_crop op

When setting TRY crop on the sub-device the mutex was erroneously acquired
rather than released on exit path. This bug is present in kernels starting
from v3.2.

Cc: stable@vger.kernel.org
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca - ov534: Add Hue control

Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] Input: move drivers/input/fixp-arith.h to include/linux

Move drivers/input/fixp-arith.h to include/linux so that the functions
defined there can be used by other subsystems, for instance some video
devices ISPs can control the output HUE value by setting registers for
sin(HUE) and cos(HUE).

Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca - ov534: Add Saturation control

Also merge the "COLORS" control into it as it was V4L2_CID_SATURATION
anyway.

Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca_pac7311: Remove vflip control

Enabling vflip leads to a much better image, with vflip disabled the
image looks washed out as if there is a too high brightness setting.

Since we don't know how to lower the brightness setting when not
vflipping, simply always vflip and tell userspace to flip the image back,
resulting in a much better (less washed out) image.

Since the image is now no longer too bright, also modify the luminance
level the auto-gain algorithm aims for.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca_pac7311: Set register page at start of init

Our init sequence was not setting the register page to point to bank 1
before setting what should be the control reg. This causes the camera to
sometimes have its LED on after init. First selecting register bank 1,
rather then assuming the current register bank is bank 1, fixes this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca_pac7311: Convert to the control framework

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca: Remove gspca_auto_gain_n_exposure function

Now that the pac207 driver has been converted to the control framework, there
are no remaining users.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gscpa_pac207: Switch to coarse_grained_expo auto gain algorithm

The pac207's exposure control is a clock-divider, so it goes with quite
big steps. So lets use an autogain algorithm optimised for that.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca_pac207: Convert to the control framework

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gscpa_pac207: use usb_err for error handling

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gscpa: Move ctrl_handler to gspca_dev

We intend to eventually port all sub-drivers to the control-framework. At
which point it will make more sense to have the ctrl_handler in gspca_dev
then to have it in the subdrivers. Lets move it there now, to avoid a lot
of work to move it later.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca_mars: Convert to the control framework

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gscpa_stv06xx: Make sd_desc const

Now that stv06xx is using the control framework it is no longer necessary
to have a (non const) copy of sd_desc inside the sd specific data struct.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca_stv06xx: Convert to the control framework

HdG:
1) Let the gspca-core cleanup the controls on control-init error, like
with the other converted sub drivers
2) Note this also fixes a bug in the hdcs1020 support which was wrongly
reporting an exposure range of 0-65535, even though the effective range was
only 0-255

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca_sn9c20x: Whitespace fixes

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gcpca_sn9c20x: Convert to the control framework

HdG: Small fix: don't register some controls for sensors which don't
have an implementation for them.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca_zc3xx: Convert to the control framework

The initial version was done by HV, corrections were made by HdG, and some
final small changes again by HV.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca_zc3xx: Disable the highest quality setting as it is not usable

Even with BRC the highest quality setting is not usable, BRC strips so
much data from each MCU that the quality becomes worse then using a lower
quality setting to begin with.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca_zc3xx: Always automatically adjust BRC as needed

Always automatically adjust the Bit Rate Control setting as needed, independent
of the sensor type. BRC is needed to not run out of bandwidth with higher
quality settings independent of the sensor.

Also only automatically adjust BRC, and don't adjust the JPEG quality control
automatically, as that is not needed and leads to ugly flashes when it is
changed. Note that before this patch-set the quality was never changed
either due to the bugs in the quality handling fixed in previous patches in
this set.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca_zc3xx: Fix JPEG quality setting code

The current code is using bits 0-1 of register 8 of the zc3xx controller
to set the JPEG quality, but the correct bits are bits 1-2. Bit 0 selects
between truncation or rounding in the quantization phase of the compression,
since rounding generally gives better results it should thus always be 1.

This patch also corrects the quality percentages which belong to the 4
different settings.

Last this patch removes the different reg 8 defaults depending on the sensor
type. Some of them where going for a default quality setting of 50%, which
generally is not necessary in any way and results in poor image quality.
75% is a good default to use for all scenarios.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca_zc3xx: Fix setting of jpeg quality while streaming

When the user changes the JPEG quality while the camera is streaming, the
driver should not only change the JPEG headers send to userspace, but also
actually tell the camera to use a different quantization table.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca_gl860: Add a present check to sd_stop0

The sensor specific dev_post_unset_alt functions all try to write to the
bridge, and none free any memory, so they should be skipped if stop0
is called on disconnection.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca: Add autogain functions for use with control framework drivers

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca: Set gspca_dev->usb_err to 0 at the begin of gspca_stream_off

Just a small cleanup.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca: Call sd_stop0 on disconnect

This is necessary to ensure that worker-threads accessing the device
are stopped before our disconnect handler returns.

This causes a problem with stream_off calling sd_stop0 a second time
when the device handle is closed. This is fixed by setting
gscpa_dev->streaming to 0 on disconnect.

Note that now stream_off will never be called on a disconnected device,
and the present check can thus be removed from stream_off.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca: Use req_events in poll

So that we don't start a read stream when an app is only polling for control
events.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gscpa: Clear usb_err before calling sd methods from suspend/resume

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca: Switch to V4L2 core locking, except for the buffer queuing ioctls

Due to latency concerns the VIDIOC_QBUF, DQBUF and QUERYBUF do not use the
core lock, instead they rely only on queue_lock.

Changes by HdG:
1) Change release from the video_device to the v4l2_device, to avoid a
race on disconnect.
2) Adjust for the V4L2 core changes which cause non ioctl fops to no longer
take the V4L2 core lock.

[mchehab@redhat.com: fix a merge conflict]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca: Fix locking issues related to suspend/resume

There are two bugs here: first the calls to stop0 (in gspca_suspend) and
gspca_init_transfer (in gspca_resume) need to be called with the usb_lock held.
That's true for the other places they are called and it is what subdrivers
expect. Quite a few will unlock the usb_lock in stop0 while waiting for a
worker thread to finish, and if usb_lock isn't held then that can cause a
kernel oops.

The other problem is that a worker thread needs to detect that it has to
halt due to a suspend. Otherwise it will just go on looping. So add tests
against gspca_dev->frozen in the worker threads that need it.

Hdg, 2 minor changes:
1) The finepix device is ok with stopping reading a frame halfway through,
   so add frozen checks in all places where we also check if we're still
   streaming
2) Use gspca_dev->dev instead of gspca_dev->present to check for disconnect
   in all touched drivers. I plan to do this everywhere in the future, and
   most relevant lines in the touched drivers are already modified by this
   patch.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca: Fix querycap and incorrect return codes

Add V4L2_CAP_DEVICE_CAPS support to querycap and replace -EINVAL by
-ENOTTY whenever an ioctl is not supported.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca: Add support for control events

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gscpa: Use v4l2_fh and add G/S_PRIORITY support

In order to support control event gspca has to use struct v4l2_fh.
As a bonus feature this also gives priority handling for free.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca: Use video_drvdata(file) instead of file->private_data

Prepare for control events: free up file->private_data by using
video_drvdata(file) to get to the gspca_dev struct.

[mchehab@redhat.com: fix a compile error: ‘file’ undeclared]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca: Allow subdrivers to use the control framework

Make the necessary changes to allow subdrivers to use the control framework.
This does not add control event support, that comes later.

It add a init_control cam_op that is called after init in probe that allows
the subdriver to set up the controls.

HdG: Call v4l2_ctrl_handler_setup from resume instead of
gspca_set_default_mode, as we just want to resend the current ctrl values to
the device.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] pwc: Fix locking

My last locking rework for pwc mistakenly assumed that videbuf2 does its
own locking, but it does not! This patch fixes the missing locking by
moving over the the video_device lock, and introducing a separate lock
for the videobuf2_queue.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] videobuf2: Fix a bug in fileio emulation error handling

Various error paths in fileio_init where not setting the request-count
to 0 when unrequesting the buffers on error to init the fileio emulation.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l2-framework.txt: document v4l2_dont_use_cmd

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l2-dev: add flag to have the core lock all file operations

This used to be the default if the lock pointer was set, but now that lock is by
default only used for ioctl serialization. Those drivers that already used
core locking have this flag set explicitly, except for some drivers where
it was obvious that there was no need to serialize any file operations other
than ioctl.

The drivers that didn't need this flag were:

drivers/media/radio/dsbr100.c
drivers/media/radio/radio-isa.c
drivers/media/radio/radio-keene.c
drivers/media/radio/radio-miropcm20.c
drivers/media/radio/radio-mr800.c
drivers/media/radio/radio-tea5764.c
drivers/media/radio/radio-timb.c
drivers/media/video/vivi.c
sound/i2c/other/tea575x-tuner.c

The other drivers that use core locking and where it was not immediately
obvious that this flag wasn't needed were changed so that the flag is set
together with a comment that that driver needs work to avoid having to
set that flag. This will often involve taking the core lock in the fops
themselves.

Eventually this flag should go and it should not be used in new drivers.

There are a few reasons why we want to avoid core locking of non-ioctl
fops: in the case of mmap this can lead to a deadlock in rare situations
since when mmap is called the mmap_sem is held and it is possible for
other parts of the code to take that lock as well (copy_from_user()/copy_to_user()
perform a down_read(&mm->mmap_sem) when a page fault occurs).

It is very unlikely that that happens since the core lock serializes all
fops, but the kernel warns about it if lock validation is turned on.

For poll it is also undesirable to take the core lock as that can introduce
increased latency. The same is true for read/write.

While it was possible to make flags or something to turn on/off taking the
core lock for each file operation, in practice it is much simpler to just
not take it at all except for ioctl and leave it to the driver to take the
lock. There are only a handful fops compared to the zillion ioctls we have.

I also wanted to make it obvious which drivers still take the lock for all
fops, so that's why I chose to have drivers set it explicitly.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l2-ioctl: handle priority handling based on a table lookup

Rather than checking the priority for each ioctl that needs to, just mark
such ioctls in the table and do it only once.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] tea575x-tuner: mark VIDIOC_S_HW_FREQ_SEEK as an invalid ioctl

The tea575x-tuner framework can support the VIDIOC_S_HW_FREQ_SEEK for only
some of the tea575x-based boards. Mark this ioctl as invalid if the board
doesn't support it.

This fixes an issue with S_HW_FREQ_SEEK in combination with priority handling:
since the priority check is done first it could return -EBUSY, even though
calling the S_HW_FREQ_SEEK ioctl would return -ENOTTY. It should always return
ENOTTY in such a case.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l2-dev/ioctl: determine the valid ioctls upfront

Rather than testing whether an ioctl is implemented in the driver or not
every time the ioctl is called, do it upfront when the device is registered.

This also allows a driver to disable certain ioctls based on the capabilities
of the detected board, something you can't do today without creating separate
v4l2_ioctl_ops structs for each new variation.

For the most part it is pretty straightforward, but for control ioctls a flag
is needed since it is possible that you have per-filehandle controls, and that
can't be determined upfront of course.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l2-dev: make it possible to skip locking for selected ioctls

Using the V4L2 core lock is a very robust method that is usually very good
at doing the right thing. But some drivers, particularly USB drivers, may
want to prevent the core from taking the lock for specific ioctls, particularly
buffer queuing ioctls.

The reason is that certain commands like S_CTRL can take a long time to process
over USB and all the time the core has the lock, preventing VIDIOC_DQBUF from
proceeding, even though a frame may be ready in the queue.

This introduces unwanted latency.

Since the buffer queuing commands often have their own internal lock it is
often not necessary to take the core lock. Drivers can now say that they don't
want the core to take the lock for specific ioctls.

As it is a specific opt-out it makes it clear to the reviewer that those
ioctls will need more care when reviewing.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] smiapp: Add driver

Add driver for SMIA++/SMIA image sensors. The driver exposes the sensor as
three subdevs, pixel array, binner and scaler --- in case the device has a
scaler.

Currently it relies on the board code for external clock handling. There is
no fast way out of this dependency before the ISP drivers (omap3isp) among
others will be able to export that clock through the clock framework
instead.

Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] smiapp: Generic SMIA++/SMIA PLL calculator

Calculate PLL configuration based on input data: sensor configuration, board
properties and sensor-specific limits.

[mchehab@redhat.com: Fix a Kconfig conflict affecting APTINA_PLL]
Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>