i2c: pxa: clear all master action bits in i2c_pxa_stop_message()

[ Upstream commit e81c979f4e071d516aa27cf5a0c3939da00dc1ca ]

If we timeout during a message transfer, the control register may
contain bits that cause an action to be set. Read-modify-writing the
register leaving these bits set may trigger the hardware to attempt
one of these actions unintentionally.

Always clear these bits when cleaning up after a message or after
a timeout.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

f2fs: report delalloc reserve as non-free in statfs for project quota

[ Upstream commit baaa7ebf25c78c5cb712fac16b7f549100beddd3 ]

This reserved space isn't committed yet but cannot be used for
allocations. For userspace it has no difference from used space.

See the same fix in ext4 commit f06925c73942 ("ext4: report delalloc
reserve as non-free in statfs for project quota").

Fixes: ddc34e328d06 ("f2fs: introduce f2fs_statfs_project")
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iio: bmp280: fix compensation of humidity

[ Upstream commit dee2dabc0e4115b80945fe2c91603e634f4b4686 ]

Limit the output of humidity compensation to the range between 0 and 100
percent.

Depending on the calibration parameters of the individual sensor it
happens, that a humidity above 100 percent or below 0 percent is
calculated, which don't make sense in terms of relative humidity.

Add a clamp to the compensation formula as described in the datasheet of
the sensor in chapter 4.2.3.

Although this clamp is documented, it was never in the driver of the
kernel.

It depends on the circumstances (calibration parameters, temperature,
humidity) if one can see a value above 100 percent without the clamp.
The writer of this patch was working with this type of sensor without
noting this error. So it seems to be a rare event when this bug occures.

Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

rtc: mc13xxx: fix a double-unlock issue

[ Upstream commit 8816cd726a4fee197af2d851cbe25991ae19ea14 ]

In function mc13xxx_rtc_probe, the mc13xxx_unlock() is called
before rtc_register_device(). But in the error path of
rtc_register_device(), the mc13xxx_unlock() is called again,
which causes a double-unlock problem. Thus add a call of the
function “mc13xxx_lock” in an if branch for the completion
of the exception handling.

Fixes: e4ae7023e182a ("rtc: mc13xxx: set range")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Link: https://lore.kernel.org/r/20200503182235.1652-1-wu000273@umn.edu
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/kasan: Fix stack overflow by increasing THREAD_SHIFT

[ Upstream commit edbadaf0671072298e506074128b64e003c5812c ]

When CONFIG_KASAN is selected, the stack usage is increased.

In the same way as x86 and arm64 architectures, increase
THREAD_SHIFT when CONFIG_KASAN is selected.

Fixes: 2edb16efc899 ("powerpc/32: Add KASAN support")
Reported-by: <erhard_f@mailbox.org>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=207129
Link: https://lore.kernel.org/r/2c50f3b1c9bbaa4217c9a98f3044bd2a36c46a4f.1586361277.git.christophe.leroy@c-s.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>

Input: edt-ft5x06 - fix get_default register write access

[ Upstream commit 255cdaf73412de13608fb776101402dca68bed2b ]

Since commit b6eba86030bf ("Input: edt-ft5x06 - add offset support for
ev-ft5726") offset-x and offset-y is supported. Devices using those
offset parameters don't support the offset parameter so we need to add
the NO_REGISTER check for edt_ft5x06_ts_get_defaults().

Fixes: b6eba86030bf ("Input: edt-ft5x06 - add offset support for ev-ft5726")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20200227112819.16754-2-m.felsch@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: qla2xxx: Fix issue with adapter's stopping state

[ Upstream commit 803e45550b11c8e43d89812356fe6f105adebdf9 ]

The goal of the following command sequence is to restart the adapter.
However, the tgt_stop flag remains set, indicating that the adapter is
still in stopping state even after re-enabling it.

echo 0x7fffffff > /sys/module/qla2xxx/parameters/logging
modprobe target_core_mod
modprobe tcm_qla2xxx
mkdir /sys/kernel/config/target/qla2xxx
mkdir /sys/kernel/config/target/qla2xxx/<port-name>
mkdir /sys/kernel/config/target/qla2xxx/<port-name>/tpgt_1
echo 1 > /sys/kernel/config/target/qla2xxx/<port-name>/tpgt_1/enable
echo 0 > /sys/kernel/config/target/qla2xxx/<port-name>/tpgt_1/enable
echo 1 > /sys/kernel/config/target/qla2xxx/<port-name>/tpgt_1/enable

kernel: PID 1396:qla_target.c:1555 qlt_stop_phase1(): tgt_stop 0x0, tgt_stopped 0x0
kernel: qla2xxx [0001:00:02.0]-e803:1: PID 1396:qla_target.c:1567: Stopping target for host 1(c0000000033557e8)
kernel: PID 1396:qla_target.c:1579 qlt_stop_phase1(): tgt_stop 0x1, tgt_stopped 0x0
kernel: PID 1396:qla_target.c:1266 qlt_schedule_sess_for_deletion(): tgt_stop 0x1, tgt_stopped 0x0
kernel: qla2xxx [0001:00:02.0]-e801:1: PID 1396:qla_target.c:1316: Scheduling sess c00000002d5cd800 for deletion 21:00:00:24:ff:7f:35:c7
<skipped>
kernel: qla2xxx [0001:00:02.0]-290a:1: PID 340:qla_target.c:1187: qlt_unreg_sess sess c00000002d5cd800 for deletion 21:00:00:24:ff:7f:35:c7
<skipped>
kernel: qla2xxx [0001:00:02.0]-f801:1: PID 340:qla_target.c:1145: Unregistration of sess c00000002d5cd800 21:00:00:24:ff:7f:35:c7 finished fcp_cnt 0
kernel: PID 340:qla_target.c:1155 qlt_free_session_done(): tgt_stop 0x1, tgt_stopped 0x0
kernel: qla2xxx [0001:00:02.0]-4807:1: PID 346:qla_os.c:6329: ISP abort scheduled.
<skipped>
kernel: qla2xxx [0001:00:02.0]-28f1:1: PID 346:qla_os.c:3956: Mark all dev lost
kernel: PID 346:qla_target.c:1266 qlt_schedule_sess_for_deletion(): tgt_stop 0x1, tgt_stopped 0x0
kernel: qla2xxx [0001:00:02.0]-4808:1: PID 346:qla_os.c:6338: ISP abort end.
<skipped>
kernel: PID 1396:qla_target.c:6812 qlt_enable_vha(): tgt_stop 0x1, tgt_stopped 0x0
<skipped>
kernel: qla2xxx [0001:00:02.0]-4807:1: PID 346:qla_os.c:6329: ISP abort scheduled.
<skipped>
kernel: qla2xxx [0001:00:02.0]-4808:1: PID 346:qla_os.c:6338: ISP abort end.

qlt_handle_cmd_for_atio() rejects the request to send commands because the
adapter is in the stopping state:

kernel: PID 0:qla_target.c:4442 qlt_handle_cmd_for_atio(): tgt_stop 0x1, tgt_stopped 0x0
kernel: qla2xxx [0001:00:02.0]-3861:1: PID 0:qla_target.c:4447: New command while device c000000005314600 is shutting down
kernel: qla2xxx [0001:00:02.0]-e85f:1: PID 0:qla_target.c:5728: qla_target: Unable to send command to target

This patch calls qla_stop_phase2() in addition to qlt_stop_phase1() in
tcm_qla2xxx_tpg_enable_store() and tcm_qla2xxx_npiv_tpg_enable_store(). The
qlt_stop_phase1() marks adapter as stopping (tgt_stop == 0x1, tgt_stopped
== 0x0) but qlt_stop_phase2() marks adapter as stopped (tgt_stop == 0x0,
tgt_stopped == 0x1).

Link: https://lore.kernel.org/r/52be1e8a3537f6c5407eae3edd4c8e08a9545ea5.camel@yadro.com
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Viacheslav Dubeyko <v.dubeiko@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: Allow pci_resize_resource() for devices on root bus

[ Upstream commit d09ddd8190fbdc07696bf34b548ae15aa1816714 ]

When resizing a BAR, pci_reassign_bridge_resources() is invoked to bring
the bridge windows of parent bridges in line with the new BAR assignment.

This assumes the device whose BAR is being resized lives on a subordinate
bus, but this is not necessarily the case. A device may live on the root
bus, in which case dev->bus->self is NULL, and passing a NULL pci_dev
pointer to pci_reassign_bridge_resources() will cause it to crash.

So let's make the call to pci_reassign_bridge_resources() conditional on
whether dev->bus->self is non-NULL in the first place.

Fixes: 8bb705e3e79d84e7 ("PCI: Add pci_resize_resource() for resizing BARs")
Link: https://lore.kernel.org/r/20200421162256.26887-1-ardb@kernel.org
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ALSA: isa/wavefront: prevent out of bounds write in ioctl

[ Upstream commit 7f0d5053c5a9d23fe5c2d337495a9d79038d267b ]

The "header->number" comes from the ioctl and it needs to be clamped to
prevent out of bounds writes.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200501094011.GA960082@mwanda
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ALSA: hda/realtek - Introduce polarity for micmute LED GPIO

[ Upstream commit dbd13179780555ecd3c992dea1222ca31920e892 ]

Currently mute LED and micmute LED share the same GPIO polarity.

So split the polarity for mute and micmute, in case they have different
polarities.

Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20200430083255.5093-1-kai.heng.feng@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: meson: fixup SCP sram nodes

[ Upstream commit 9ecded10b4b6af238da0c86197b0418912e7513e ]

The GX and AXG SCP sram nodes were using invalid compatible and
node names for the sram entries.

Fixup the sram entries node names, and use proper compatible for them.

It notably fixes:
sram@c8000000: 'scp-shmem@0', 'scp-shmem@200' do not match any of the regexes: '^([a-z]*-)?sram(-section)?@[a-f0-9]+$', 'pinctrl-[0-9]+'

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200326165958.19274-3-narmstrong@baylibre.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: qedi: Check for buffer overflow in qedi_set_path()

[ Upstream commit 4a4c0cfb4be74e216dd4446b254594707455bfc6 ]

Smatch complains that the "path_data->handle" variable is user controlled.
It comes from iscsi_set_path() so that seems possible.  It's harmless to
add a limit check.

The qedi->ep_tbl[] array has qedi->max_active_conns elements (which is
always ISCSI_MAX_SESS_PER_HBA (4096) elements).  The array is allocated in
the qedi_cm_alloc_mem() function.

Link: https://lore.kernel.org/r/20200428131939.GA696531@mwanda
Fixes: ace7f46ba5fd ("scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.")
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: core: free sgtables in case command setup fails

[ Upstream commit 20a66f2bf280277ab5bb22e27445153b4eb0ac88 ]

In case scsi_setup_fs_cmnd() fails we're not freeing the sgtables allocated
by scsi_init_io(), thus we leak the allocated memory.

Free the sgtables allocated by scsi_init_io() in case scsi_setup_fs_cmnd()
fails.

Technically scsi_setup_scsi_cmnd() does not suffer from this problem as it
can only fail if scsi_init_io() fails, so it does not have sgtables
allocated. But to maintain symmetry and as a measure of defensive
programming, free the sgtables on scsi_setup_scsi_cmnd() failure as well.
scsi_mq_free_sgtables() has safeguards against double-freeing of memory so
this is safe to do.

While we're at it, rename scsi_mq_free_sgtables() to scsi_free_sgtables().

Link: https://bugzilla.kernel.org/show_bug.cgi?id=205595
Link: https://lore.kernel.org/r/20200428104605.8143-2-johannes.thumshirn@wdc.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: stm32: Add missing ethernet PHY reset on AV96

[ Upstream commit 010ca9fe500bfe365860b50220ff80541c18f0e1 ]

Add PHY reset GPIO on AV96 ethernet PHY.

Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: integrator: Add some Kconfig selections

[ Upstream commit d2854bbe5f5c4b4bec8061caf4f2e603d8819446 ]

The CMA and DMA_CMA Kconfig options need to be selected
by the Integrator in order to produce boot console on some
Integrator systems.

The REGULATOR and REGULATOR_FIXED_VOLTAGE need to be
selected in order to boot the system from an external
MMC card when using MMCI/PL181 from the device tree
probe path.

Select these things directly from the Kconfig so we are
sure to be able to bring the systems up with console
from any device tree.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: davinci-mcasp: Fix dma_chan refcnt leak when getting dma type

[ Upstream commit a697ae6ea56e23397341b027098c1b11d9ab13da ]

davinci_mcasp_get_dma_type() invokes dma_request_chan(), which returns a
reference of the specified dma_chan object to "chan" with increased
refcnt.

When davinci_mcasp_get_dma_type() returns, local variable "chan" becomes
invalid, so the refcount should be decreased to keep refcount balanced.

The reference counting issue happens in one exception handling path of
davinci_mcasp_get_dma_type(). When chan device is NULL, the function
forgets to decrease the refcnt increased by dma_request_chan(), causing
a refcnt leak.

Fix this issue by calling dma_release_channel() when chan device is
NULL.

Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/1587818916-38730-1-git-send-email-xiyuyang19@fudan.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: renesas: Fix IOMMU device node names

[ Upstream commit ae990a1de014396ffc8d0fcc31b6888c9b0ce59a ]

Fix IOMMU device node names as "iommu@".

Fixes: bbb44da0b595 ("ARM: dts: r8a7743: Add IPMMU DT nodes")
Fixes: 0dcba3de5835 ("ARM: dts: r8a7745: Add IPMMU DT nodes")
Fixes: 350ae49b97c4 ("ARM: dts: r8a7744: Add IPMMU DT nodes")
Fixes: 70496727c082 ("ARM: shmobile: r8a7790: Add IPMMU DT nodes")
Fixes: f1951852ed17 ("ARM: shmobile: r8a7791: Add IPMMU DT nodes")
Fixes: 098cb3a601e6 ("ARM: shmobile: r8a7793: Add IPMMU nodes")
Fixes: 1cb2794f6082 ("ARM: shmobile: r8a7794: Add IPMMU DT nodes")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/1587461756-13317-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>

backlight: lp855x: Ensure regulators are disabled on probe failure

[ Upstream commit d8207c155a7c6015eb7f43739baa7dfb1fa638af ]

If probing the LP885x backlight fails after the regulators have been
enabled, then the following warning is seen when releasing the
regulators ...

 WARNING: CPU: 1 PID: 289 at drivers/regulator/core.c:2051 _regulator_put.part.28+0x158/0x160
 Modules linked in: tegra_xudc lp855x_bl(+) host1x pwm_tegra ip_tables x_tables ipv6 nf_defrag_ipv6
 CPU: 1 PID: 289 Comm: systemd-udevd Not tainted 5.6.0-rc2-next-20200224 #1
 Hardware name: NVIDIA Jetson TX1 Developer Kit (DT)

 ...

 Call trace:
  _regulator_put.part.28+0x158/0x160
  regulator_put+0x34/0x50
  devm_regulator_release+0x10/0x18
  release_nodes+0x12c/0x230
  devres_release_all+0x34/0x50
  really_probe+0x1c0/0x370
  driver_probe_device+0x58/0x100
  device_driver_attach+0x6c/0x78
  __driver_attach+0xb0/0xf0
  bus_for_each_dev+0x68/0xc8
  driver_attach+0x20/0x28
  bus_add_driver+0x160/0x1f0
  driver_register+0x60/0x110
  i2c_register_driver+0x40/0x80
  lp855x_driver_init+0x20/0x1000 [lp855x_bl]
  do_one_initcall+0x58/0x1a0
  do_init_module+0x54/0x1d0
  load_module+0x1d80/0x21c8
  __do_sys_finit_module+0xe8/0x100
  __arm64_sys_finit_module+0x18/0x20
  el0_svc_common.constprop.3+0xb0/0x168
  do_el0_svc+0x20/0x98
  el0_sync_handler+0xf4/0x1b0
  el0_sync+0x140/0x180

Fix this by ensuring that the regulators are disabled, if enabled, on
probe failure.

Finally, ensure that the vddio regulator is disabled in the driver
remove handler.

Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: fsl_esai: Disable exception interrupt before scheduling tasklet

[ Upstream commit 1fecbb71fe0e46b886f84e3b6decca6643c3af6d ]

Disable exception interrupt before scheduling tasklet, otherwise if
the tasklet isn't handled immediately, there will be endless xrun
interrupt.

Fixes: 7ccafa2b3879 ("ASoC: fsl_esai: recover the channel swap after xrun")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/a8f2ad955aac9e52587beedc1133b3efbe746895.1587968824.git.shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

clk: qcom: msm8916: Fix the address location of pll->config_reg

[ Upstream commit f47ab3c2f5338828a67e89d5f688d2cef9605245 ]

During the process of debugging a processor derived from the msm8916 which
we found the new processor was not starting one of its PLLs.

After tracing the addresses and writes that downstream was doing and
comparing to upstream it became obvious that we were writing to a different
register location than downstream when trying to configure the PLL.

This error is also present in upstream msm8916.

As an example clk-pll.c::clk_pll_recalc_rate wants to write to
pll->config_reg updating the bit-field POST_DIV_RATIO. That bit-field is
defined in PLL_USER_CTL not in PLL_CONFIG_CTL. Taking the BIMC PLL as an
example

lm80-p0436-13_c_qc_snapdragon_410_processor_hrd.pdf

0x01823010 GCC_BIMC_PLL_USER_CTL
0x01823014 GCC_BIMC_PLL_CONFIG_CTL

This pattern is repeated for gpll0, gpll1, gpll2 and bimc_pll.

This error is likely not apparent since the bootloader will already have
initialized these PLLs.

This patch corrects the location of config_reg from PLL_CONFIG_CTL to
PLL_USER_CTL for all relevant PLLs on msm8916.

Fixes commit 3966fab8b6ab ("clk: qcom: Add MSM8916 Global Clock Controller support")

Cc: Georgi Djakov <georgi.djakov@linaro.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lkml.kernel.org/r/20200329124116.4185447-1-bryan.odonoghue@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

remoteproc: Fix IDR initialisation in rproc_alloc()

[ Upstream commit 6442df49400b466431979e7634849a464a5f1861 ]

If ida_simple_get() returns an error when called in rproc_alloc(),
put_device() is called to clean things up.  By this time the rproc
device type has been assigned, with rproc_type_release() as the
release function.

The first thing rproc_type_release() does is call:
    idr_destroy(&rproc->notifyids);

But at the time the ida_simple_get() call is made, the notifyids
field in the remoteproc structure has not been initialized.

I'm not actually sure this case causes an observable problem, but
it's incorrect.  Fix this by initializing the notifyids field before
calling ida_simple_get() in rproc_alloc().

Fixes: b5ab5e24e960 ("remoteproc: maintain a generic child device for each rproc")
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200415204858.2448-2-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iio: pressure: bmp280: Tolerate IRQ before registering

[ Upstream commit 97b31a6f5fb95b1ec6575b78a7240baddba34384 ]

With DEBUG_SHIRQ enabled we have a kernel crash

[  116.482696] BUG: kernel NULL pointer dereference, address: 0000000000000000

...

[  116.606571] Call Trace:
[  116.609023]  <IRQ>
[  116.611047]  complete+0x34/0x50
[  116.614206]  bmp085_eoc_irq+0x9/0x10 [bmp280]

because DEBUG_SHIRQ mechanism fires an IRQ before registration and drivers
ought to be able to handle an interrupt happening before request_irq() returns.

Fixes: aae953949651 ("iio: pressure: bmp280: add support for BMP085 EOC interrupt")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: SOF: imx8: Fix randbuild error

[ Upstream commit fe17e6cdc0fefca96ba9659be4b2b07487cbf0c5 ]

when do randconfig like this:
CONFIG_SND_SOC_SOF_IMX8_SUPPORT=y
CONFIG_SND_SOC_SOF_IMX8=y
CONFIG_SND_SOC_SOF_OF=y
CONFIG_IMX_DSP=m
CONFIG_IMX_SCU=y

there is a link error:

sound/soc/sof/imx/imx8.o: In function 'imx8_send_msg':
imx8.c:(.text+0x380): undefined reference to 'imx_dsp_ring_doorbell'

Select IMX_DSP in SND_SOC_SOF_IMX8_SUPPORT to fix this

Fixes: f9ad75468453 ("ASoC: SOF: imx: fix reverse CONFIG_SND_SOC_SOF_OF dependency")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20200409071832.2039-2-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

i2c: piix4: Detect secondary SMBus controller on AMD AM4 chipsets

[ Upstream commit f27237c174fd9653033330e4e532cd9d153ce824 ]

The AMD X370 and other AM4 chipsets (A/B/X 3/4/5 parts) and Threadripper
equivalents have a secondary SMBus controller at I/O port address
0x0B20.  This bus is used by several manufacturers to control
motherboard RGB lighting via embedded controllers.  I have been using
this bus in my OpenRGB project to control the Aura RGB on many
motherboards and ASRock also uses this bus for their Polychrome RGB
controller.

I am not aware of any CZ-compatible platforms which do not have the
second SMBus channel.  All of AMD's AM4- and Threadripper- series
chipsets that OpenRGB users have tested appear to have this secondary
bus.  I also noticed this secondary bus is present on older AMD
platforms including my FM1 home server.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202587
Signed-off-by: Adam Honse <calcprogrammer1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: tegra: tegra_wm8903: Support nvidia, headset property

[ Upstream commit 3ef9d5073b552d56bd6daf2af1e89b7e8d4df183 ]

The microphone-jack state needs to be masked in a case of a 4-pin jack
when microphone and ground pins are shorted. Presence of nvidia,headset
tells that WM8903 CODEC driver should mask microphone's status if short
circuit is detected, i.e headphones are inserted.

Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200330204011.18465-3-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

clk: sunxi: Fix incorrect usage of round_down()

[ Upstream commit ee25d9742dabed3fd18158b518f846abeb70f319 ]

round_down() can only round to powers of 2. If round_down() is asked
to round to something that is not a power of 2, incorrect results are
produced. The incorrect results can be both too large and too small.

Instead, use rounddown() which can round to any number.

Fixes: 6a721db180a2 ("clk: sunxi: Add A31 clocks support")
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>

power: supply: bq24257_charger: Replace depends on REGMAP_I2C with select

[ Upstream commit 87c3d579c8ed0eaea6b1567d529a8daa85a2bc6c ]

regmap is a library function that gets selected by drivers that need
it. No driver modules should depend on it. Depending on REGMAP_I2C makes
this driver only build if another driver already selected REGMAP_I2C,
as the symbol can't be selected through the menu kernel configuration.

Fixes: 2219a935963e ("power_supply: Add TI BQ24257 charger driver")
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Linux 5.4.48

perf symbols: Fix kernel maps for kcore and eBPF

commit 0affd0e5262b6d40f5f63466d88933e99698e240 upstream.

Adjust 'map->pgoff' also when moving a map's start address.

Example with v5.4.34 based kernel:

  Before:

    $ sudo tools/perf/perf record -a --kcore -e intel_pt//k sleep 1
    [ perf record: Woken up 1 times to write data ]
    [ perf record: Captured and wrote 1.958 MB perf.data ]
    $ sudo tools/perf/perf script --itrace=e >/dev/null
    Warning:
    961 instruction trace errors

  After:

    $ sudo tools/perf/perf script --itrace=e >/dev/null
    $

Committer testing:

  # uname -a
  Linux seventh 5.6.10-100.fc30.x86_64 #1 SMP Mon May 4 15:36:44 UTC 2020 x86_64 x86_64 x86_64 GNU/Linux
  #

Before:

  # perf record -a --kcore -e intel_pt//k sleep 1
  [ perf record: Woken up 1 times to write data ]
  [ perf record: Captured and wrote 0.923 MB perf.data ]
  # perf script --itrace=e >/dev/null
  Warning:
  295 instruction trace errors
  #

After:

  # perf record -a --kcore -e intel_pt//k sleep 1
  [ perf record: Woken up 1 times to write data ]
  [ perf record: Captured and wrote 0.919 MB perf.data ]
  # perf script --itrace=e >/dev/null
  #

Fixes: fb5a88d4131a ("perf tools: Preserve eBPF maps when loading kcore")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: stable@vger.kernel.org
Link: http://lore.kernel.org/lkml/20200602112505.1406-1-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf symbols: Fix debuginfo search for Ubuntu

commit 85afd35575a3c1a3a905722dde5ee70b49282e70 upstream.

Reportedly, from 19.10 Ubuntu has begun mixing up the location of some
debug symbol files, putting files expected to be in
/usr/lib/debug/usr/lib into /usr/lib/debug/lib instead. Fix by adding
another dso_binary_type.

Example on Ubuntu 20.04

  Before:

    $ perf record -e intel_pt//u uname
    Linux
    [ perf record: Woken up 1 times to write data ]
    [ perf record: Captured and wrote 0.030 MB perf.data ]
    $ perf script --call-trace | head -5
           uname 14003 [005] 15321.764958566:  cbr: 42 freq: 4219 MHz (156%)
           uname 14003 [005] 15321.764958566: (/usr/lib/x86_64-linux-gnu/ld-2.31.so              )          7f1e71cc4100
           uname 14003 [005] 15321.764961566: (/usr/lib/x86_64-linux-gnu/ld-2.31.so              )              7f1e71cc4df0
           uname 14003 [005] 15321.764961900: (/usr/lib/x86_64-linux-gnu/ld-2.31.so              )              7f1e71cc4e18
           uname 14003 [005] 15321.764963233: (/usr/lib/x86_64-linux-gnu/ld-2.31.so              )              7f1e71cc5128

  After:

    $ perf script --call-trace | head -5
           uname 14003 [005] 15321.764958566:  cbr: 42 freq: 4219 MHz (156%)
           uname 14003 [005] 15321.764958566: (/usr/lib/x86_64-linux-gnu/ld-2.31.so              )      _start
           uname 14003 [005] 15321.764961566: (/usr/lib/x86_64-linux-gnu/ld-2.31.so              )          _dl_start
           uname 14003 [005] 15321.764961900: (/usr/lib/x86_64-linux-gnu/ld-2.31.so              )          _dl_start
           uname 14003 [005] 15321.764963233: (/usr/lib/x86_64-linux-gnu/ld-2.31.so              )          _dl_start

Reported-by: Travis Downs <travis.downs@gmail.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: stable@vger.kernel.org
Link: http://lore.kernel.org/lkml/20200526155207.9172-1-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf probe: Check address correctness by map instead of _etext

commit 2ae5d0d7d8868df7c05c2013c0b9cddd4d40610e upstream.

Since commit 03db8b583d1c ("perf tools: Fix
maps__find_symbol_by_name()") introduced map address range check in
maps__find_symbol_by_name(), we can not get "_etext" from kernel map
because _etext is placed on the edge of the kernel .text section (=
kernel map in perf.)

To fix this issue, this checks the address correctness by map address
range information (map->start and map->end) instead of using _etext
address.

This can cause an error if the target inlined function is embedded in
both __init function and normal function.

For exaample, request_resource() is a normal function but also embedded
in __init reserve_setup(). In this case, the probe point in
reserve_setup() must be skipped.

However, without this fix, it failes to setup all probe points:

  # ./perf probe -v request_resource
  probe-definition(0): request_resource
  symbol:request_resource file:(null) line:0 offset:0 return:0 lazy:(null)
  0 arguments
  Looking at the vmlinux_path (8 entries long)
  Using /usr/lib/debug/lib/modules/5.5.17-200.fc31.x86_64/vmlinux for symbols
  Open Debuginfo file: /usr/lib/debug/lib/modules/5.5.17-200.fc31.x86_64/vmlinux
  Try to find probe point from debuginfo.
  Matched function: request_resource [15e29ad]
  found inline addr: 0xffffffff82fbf892
  Probe point found: reserve_setup+204
  found inline addr: 0xffffffff810e9790
  Probe point found: request_resource+0
  Found 2 probe_trace_events.
  Opening /sys/kernel/debug/tracing//kprobe_events write=1
  Opening /sys/kernel/debug/tracing//README write=0
  Writing event: p:probe/request_resource _text+33290386
  Failed to write event: Invalid argument
    Error: Failed to add events. Reason: Invalid argument (Code: -22)
  #

With this fix,

  # ./perf probe request_resource
  reserve_setup is out of .text, skip it.
  Added new events:
    (null):(null)        (on request_resource)
    probe:request_resource (on request_resource)

  You can now use it in all perf tools, such as:

   perf record -e probe:request_resource -aR sleep 1

  #

Fixes: 03db8b583d1c ("perf tools: Fix maps__find_symbol_by_name()")
Reported-by: Arnaldo Carvalho de Melo <acme@kernel.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: stable@vger.kernel.org
Link: http://lore.kernel.org/lkml/158763967332.30755.4922496724365529088.stgit@devnote2
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf probe: Fix to check blacklist address correctly

commit 80526491c2ca6abc028c0f0dbb0707a1f35fb18a upstream.

Fix to check kprobe blacklist address correctly with relocated address
by adjusting debuginfo address.

Since the address in the debuginfo is same as objdump, it is different
from relocated kernel address with KASLR.  Thus, 'perf probe' always
misses to catch the blacklisted addresses.

Without this patch, 'perf probe' can not detect the blacklist addresses
on a KASLR enabled kernel.

  # perf probe kprobe_dispatcher
  Failed to write event: Invalid argument
    Error: Failed to add events.
  #

With this patch, it correctly shows the error message.

  # perf probe kprobe_dispatcher
  kprobe_dispatcher is blacklisted function, skip it.
  Probe point 'kprobe_dispatcher' not found.
    Error: Failed to add events.
  #

Fixes: 9aaf5a5f479b ("perf probe: Check kprobes blacklist when adding new events")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: stable@vger.kernel.org
Link: http://lore.kernel.org/lkml/158763966411.30755.5882376357738273695.stgit@devnote2
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf probe: Do not show the skipped events

commit f41ebe9defacddeae96a872a33f0f22ced0bfcef upstream.

When a probe point is expanded to several places (like inlined) and if
some of them are skipped because of blacklisted or __init function,
those trace_events has no event name. It must be skipped while showing
results.

Without this fix, you can see "(null):(null)" on the list,

  # ./perf probe request_resource
  reserve_setup is out of .text, skip it.
  Added new events:
    (null):(null)        (on request_resource)
    probe:request_resource (on request_resource)

  You can now use it in all perf tools, such as:

   perf record -e probe:request_resource -aR sleep 1

  #

With this fix, it is ignored:

  # ./perf probe request_resource
  reserve_setup is out of .text, skip it.
  Added new events:
    probe:request_resource (on request_resource)

  You can now use it in all perf tools, such as:

   perf record -e probe:request_resource -aR sleep 1

  #

Fixes: 5a51fcd1f30c ("perf probe: Skip kernel symbols which is out of .text")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: stable@vger.kernel.org
Link: http://lore.kernel.org/lkml/158763968263.30755.12800484151476026340.stgit@devnote2
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

f2fs: fix checkpoint=disable:%u%%

commit 1ae18f71cb522684bac1718f5c188fb5e30eb23d upstream.

When parsing the mount option, we don't have sbi->user_block_count.
Should do it after getting it.

Cc: <stable@vger.kernel.org>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

w1: omap-hdq: cleanup to add missing newline for some dev_dbg

commit 5e02f3b31704e24537697bce54f8156bdb72b7a6 upstream.

Otherwise it will corrupt the console log during debugging.

Fixes: 7b5362a603a1 ("w1: omap_hdq: Fix some error/debug handling.")
Cc: stable@vger.kernel.org
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Link: https://lore.kernel.org/r/cd0d55749a091214106575f6e1d363c6db56622f.1590255176.git.hns@goldelico.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: rawnand: tmio: Fix the probe error path

commit 75e9a330a9bd48f97a55a08000236084fe3dae56 upstream.

nand_release() is supposed be called after MTD device registration.
Here, only nand_scan() happened, so use nand_cleanup() instead.

There is no real Fixes tag applying here as the use of nand_release()
in this driver predates by far the introduction of nand_cleanup() in
commit d44154f969a4 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
which makes this change possible. However, pointing this commit as the
culprit for backporting purposes makes sense even if this commit is not
introducing any bug.

Fixes: d44154f969a4 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-57-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: rawnand: mtk: Fix the probe error path

commit 8a82bbcadec877f5f938c54026278dfc1f05a332 upstream.

nand_release() is supposed be called after MTD device registration.
Here, only nand_scan() happened, so use nand_cleanup() instead.

There is no real Fixes tag applying here as the use of nand_release()
in this driver predates the introduction of nand_cleanup() in
commit d44154f969a4 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
which makes this change possible. However, pointing this commit as the
culprit for backporting purposes makes sense even if this commit is not
introducing any bug.

Fixes: d44154f969a4 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-28-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: rawnand: pasemi: Fix the probe error path

commit f51466901c07e6930435d30b02a21f0841174f61 upstream.

nand_cleanup() is supposed to be called on error after a successful
call to nand_scan() to free all NAND resources.

There is no real Fixes tag applying here as the use of nand_release()
in this driver predates by far the introduction of nand_cleanup() in
commit d44154f969a4 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
which makes this change possible, hence pointing it as the commit to
fix for backporting purposes, even if this commit is not introducing
any bug.

Fixes: d44154f969a4 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-41-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: rawnand: plat_nand: Fix the probe error path

commit 5284024b4dac5e94f7f374ca905c7580dbc455e9 upstream.

nand_release() is supposed be called after MTD device registration.
Here, only nand_scan() happened, so use nand_cleanup() instead.

There is no real Fixes tag applying here as the use of nand_release()
in this driver predates by far the introduction of nand_cleanup() in
commit d44154f969a4 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
which makes this change possible, hence pointing it as the commit to
fix for backporting purposes, even if this commit is not introducing
any bug.

Fixes: d44154f969a4 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-43-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: rawnand: sunxi: Fix the probe error path

commit 3d84515ffd8fb657e10fa5b1215e9f095fa7efca upstream.

nand_release() is supposed be called after MTD device registration.
Here, only nand_scan() happened, so use nand_cleanup() instead.

Fixes: 1fef62c1423b ("mtd: nand: add sunxi NAND flash controller support")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-54-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: rawnand: oxnas: Fix the probe error path

commit 154298e2a3f6c9ce1d76cdb48d89fd5b107ea1a3 upstream.

nand_release() is supposed be called after MTD device registration.
Here, only nand_scan() happened, so use nand_cleanup() instead.

While at it, be consistent and move the function call in the error
path thanks to a goto statement.

Fixes: 668592492409 ("mtd: nand: Add OX820 NAND Support")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-37-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: rawnand: socrates: Fix the probe error path

commit 9c6c2e5cc77119ce0dacb4f9feedb73ce0354421 upstream.

nand_release() is supposed be called after MTD device registration.
Here, only nand_scan() happened, so use nand_cleanup() instead.

There is no real Fixes tag applying here as the use of nand_release()
in this driver predates by far the introduction of nand_cleanup() in
commit d44154f969a4 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
which makes this change possible. However, pointing this commit as the
culprit for backporting purposes makes sense even if this commit is not
introducing any bug.

Fixes: d44154f969a4 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-51-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: rawnand: orion: Fix the probe error path

commit be238fbf78e4c7c586dac235ab967d3e565a4d1a upstream.

nand_release() is supposed be called after MTD device registration.
Here, only nand_scan() happened, so use nand_cleanup() instead.

There is no real Fixes tag applying here as the use of nand_release()
in this driver predates by far the introduction of nand_cleanup() in
commit d44154f969a4 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
which makes this change possible. However, pointing this commit as the
culprit for backporting purposes makes sense even if this commit is not
introducing any bug.

Fixes: d44154f969a4 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-34-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: rawnand: xway: Fix the probe error path

commit 34531be5e804a8e1abf314a6c3a19fe342e4a154 upstream.

nand_release() is supposed be called after MTD device registration.
Here, only nand_scan() happened, so use nand_cleanup() instead.

There is no real Fixes tag applying here as the use of nand_release()
in this driver predates the introduction of nand_cleanup() in
commit d44154f969a4 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
which makes this change possible. However, pointing this commit as the
culprit for backporting purposes makes sense even if this commit is not
introducing any bug.

Fixes: d44154f969a4 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-61-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: rawnand: ingenic: Fix the probe error path

commit de17cade0e034e9b721a6db9b488014effac1e5a upstream.

nand_release() is supposed be called after MTD device registration.
Here, only nand_scan() happened, so use nand_cleanup() instead.

There is no real Fixes tag applying here as the use of nand_release()
in this driver predates the introduction of nand_cleanup() in
commit d44154f969a4 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
which makes this change possible. Hence, pointing it as the commit to
fix for backporting purposes, even if this commit is not introducing
any bug makes sense.

Fixes: d44154f969a4 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: stable@vger.kernel.org
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Harvey Hunt <harveyhuntnexus@gmail.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-22-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: rawnand: sharpsl: Fix the probe error path

commit 0f44b3275b3798ccb97a2f51ac85871c30d6fbbc upstream.

nand_release() is supposed be called after MTD device registration.
Here, only nand_scan() happened, so use nand_cleanup() instead.

There is no Fixes tag applying here as the use of nand_release()
in this driver predates by far the introduction of nand_cleanup() in
commit d44154f969a4 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
which makes this change possible. However, pointing this commit as the
culprit for backporting purposes makes sense.

Fixes: d44154f969a4 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-49-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: rawnand: diskonchip: Fix the probe error path

commit c5be12e45940f1aa1b5dfa04db5d15ad24f7c896 upstream.

Not sure nand_cleanup() is the right function to call here but in any
case it is not nand_release(). Indeed, even a comment says that
calling nand_release() is a bit of a hack as there is no MTD device to
unregister. So switch to nand_cleanup() for now and drop this
comment.

There is no Fixes tag applying here as the use of nand_release()
in this driver predates by far the introduction of nand_cleanup() in
commit d44154f969a4 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
which makes this change possible. However, pointing this commit as the
culprit for backporting purposes makes sense even if it did not intruce
any bug.

Fixes: d44154f969a4 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-13-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: rawnand: brcmnand: fix hamming oob layout

commit 130bbde4809b011faf64f99dddc14b4b01f440c3 upstream.

First 2 bytes are used in large-page nand.

Fixes: ef5eeea6e911 ("mtd: nand: brcm: switch to mtd_ooblayout_ops")
Cc: stable@vger.kernel.org
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200512075733.745374-2-noltari@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: rawnand: onfi: Fix redundancy detection check

commit 1d5d08ee9b28cff907326b4ad5a2463fd2808be1 upstream.

During ONFI detection, the CRC derived from the parameter page and the
CRC supposed to be at the end of the parameter page are compared. If
they do not match, the second then the third copies of the page are
tried.

The current implementation compares the newly derived CRC with the CRC
contained in the first page only. So if this particular CRC area has
been corrupted, then the detection will fail for a wrong reason.

Fix this issue by checking the derived CRC against the right one.

Fixes: 39138c1f4a31 ("mtd: rawnand: use bit-wise majority to recover the ONFI param page")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200428094302.14624-4-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: rawnand: Fix nand_gpio_waitrdy()

commit e45a4b652dbd2f8b5a3b8e97e89f602a58cb28aa upstream.

Mimic what's done in nand_soft_waitrdy() and add one to the jiffies
timeout so we don't end up waiting less than actually required.

Reported-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Fixes: b0e137ad24b6c ("mtd: rawnand: Provide helper for polling GPIO R/B pin")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200518155237.297549-1-boris.brezillon@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sunrpc: clean up properly in gss_mech_unregister()

commit 24c5efe41c29ee3e55bcf5a1c9f61ca8709622e8 upstream.

gss_mech_register() calls svcauth_gss_register_pseudoflavor() for each
flavour, but gss_mech_unregister() does not call auth_domain_put().
This is unbalanced and makes it impossible to reload the module.

Change svcauth_gss_register_pseudoflavor() to return the registered
auth_domain, and save it for later release.

Cc: stable@vger.kernel.org (v2.6.12+)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206651
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sunrpc: svcauth_gss_register_pseudoflavor must reject duplicate registrations.

commit d47a5dc2888fd1b94adf1553068b8dad76cec96c upstream.

There is no valid case for supporting duplicate pseudoflavor
registrations.
Currently the silent acceptance of such registrations is hiding a bug.
The rpcsec_gss_krb5 module registers 2 flavours but does not unregister
them, so if you load, unload, reload the module, it will happily
continue to use the old registration which now has pointers to the
memory were the module was originally loaded.  This could lead to
unexpected results.

So disallow duplicate registrations.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=206651
Cc: stable@vger.kernel.org (v2.6.12+)
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kbuild: force to build vmlinux if CONFIG_MODVERSION=y

commit 4b50c8c4eaf06a825d1c005c0b1b4a8307087b83 upstream.

This code does not work as stated in the comment.

$(CONFIG_MODVERSIONS) is always empty because it is expanded before
include/config/auto.conf is included. Hence, 'make modules' with
CONFIG_MODVERSION=y cannot record the version CRCs.

This has been broken since 2003, commit ("kbuild: Enable modules to be
build using the "make dir/" syntax"). [1]

[1]: https://git.kernel.org/pub/scm/linux/kernel/git/history/history.git/commit/?id=15c6240cdc44bbeef3c4797ec860f9765ef4f1a7
Cc: linux-stable <stable@vger.kernel.org> # v2.5.71+
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/64s: Save FSCR to init_task.thread.fscr after feature init

commit 912c0a7f2b5daa3cbb2bc10f303981e493de73bd upstream.

At boot the FSCR is initialised via one of two paths. On most systems
it's set to a hard coded value in __init_FSCR().

On newer skiboot systems we use the device tree CPU features binding,
where firmware can tell Linux what bits to set in FSCR (and HFSCR).

In both cases the value that's configured at boot is not propagated
into the init_task.thread.fscr value prior to the initial fork of init
(pid 1), which means the value is not used by any processes other than
swapper (the idle task).

For the __init_FSCR() case this is OK, because the value in
init_task.thread.fscr is initialised to something sensible. However it
does mean that the value set in __init_FSCR() is not used other than
for swapper, which is odd and confusing.

The bigger problem is for the device tree CPU features case it
prevents firmware from setting (or clearing) FSCR bits for use by user
space. This means all existing kernels can not have features
enabled/disabled by firmware if those features require
setting/clearing FSCR bits.

We can handle both cases by saving the FSCR value into
init_task.thread.fscr after we have initialised it at boot. This fixes
the bug for device tree CPU features, and will allow us to simplify
the initialisation for the __init_FSCR() case in a future patch.

Fixes: 5a61ef74f269 ("powerpc/64s: Support new device tree binding for discovering CPU features")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200527145843.2761782-3-mpe@ellerman.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/64s: Don't let DT CPU features set FSCR_DSCR

commit 993e3d96fd08c3ebf7566e43be9b8cd622063e6d upstream.

The device tree CPU features binding includes FSCR bit numbers which
Linux is instructed to set by firmware.

Whether that's a good idea or not, in the case of the DSCR the Linux
implementation has a hard requirement that the FSCR_DSCR bit not be
set by default. We use it to track when a process reads/writes to
DSCR, so it must be clear to begin with.

So if firmware tells us to set FSCR_DSCR we must ignore it.

Currently this does not cause a bug in our DSCR handling because the
value of FSCR that the device tree CPU features code establishes is
only used by swapper. All other tasks use the value hard coded in
init_task.thread.fscr.

However we'd like to fix that in a future commit, at which point this
will become necessary.

Fixes: 5a61ef74f269 ("powerpc/64s: Support new device tree binding for discovering CPU features")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200527145843.2761782-2-mpe@ellerman.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/32: Disable KASAN with pages bigger than 16k

commit 888468ce725a4cd56d72dc7e5096078f7a9251a0 upstream.

Mapping of early shadow area is implemented by using a single static
page table having all entries pointing to the same early shadow page.
The shadow area must therefore occupy full PGD entries.

The shadow area has a size of 128MB starting at 0xf8000000.
With 4k pages, a PGD entry is 4MB
With 16k pages, a PGD entry is 64MB
With 64k pages, a PGD entry is 1GB which is too big.

Until we rework the early shadow mapping, disable KASAN when the page
size is too big.

Fixes: 2edb16efc899 ("powerpc/32: Add KASAN support")
Cc: stable@vger.kernel.org # v5.2+
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/7195fcde7314ccbf7a081b356084a69d421b10d4.1590660977.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/kasan: Fix shadow pages allocation failure

commit d2a91cef9bbdeb87b7449fdab1a6be6000930210 upstream.

Doing kasan pages allocation in MMU_init is too early, kernel doesn't
have access yet to the entire memory space and memblock_alloc() fails
when the kernel is a bit big.

Do it from kasan_init() instead.

Fixes: 2edb16efc899 ("powerpc/32: Add KASAN support")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/c24163ee5d5f8cdf52fefa45055ceb35435b8f15.1589866984.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/kasan: Fix issues by lowering KASAN_SHADOW_END

commit 3a66a24f6060e6775f8c02ac52329ea0152d7e58 upstream.

At the time being, KASAN_SHADOW_END is 0x100000000, which
is 0 in 32 bits representation.

This leads to a couple of issues:
- kasan_remap_early_shadow_ro() does nothing because the comparison
k_cur < k_end is always false.
- In ptdump, address comparison for markers display fails and the
marker's name is printed at the start of the KASAN area instead of
being printed at the end.

However, there is no need to shadow the KASAN shadow area itself,
so the KASAN shadow area can stop shadowing memory at the start
of itself.

With a PAGE_OFFSET set to 0xc0000000, KASAN shadow area is then going
from 0xf8000000 to 0xff000000.

Fixes: cbd18991e24f ("powerpc/mm: Fix an Oops in kasan_mmu_init()")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/ae1a3c0d19a37410c209c3fc453634cfcc0ee318.1589866984.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/32s: Fix another build failure with CONFIG_PPC_KUAP_DEBUG

commit 74016701fe5f873ae23bf02835407227138d874d upstream.

'thread' doesn't exist in kuap_check() macro.

Use 'current' instead.

Fixes: a68c31fc01ef ("powerpc/32s: Implement Kernel Userspace Access Protection")
Cc: stable@vger.kernel.org
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/b459e1600b969047a74e34251a84a3d6fdf1f312.1590858925.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/macintosh: Fix memleak in windfarm_pm112 driver

commit 93900337b9ac2f4eca427eff6d187be2dc3b5551 upstream.

create_cpu_loop() calls smu_sat_get_sdb_partition() which does
kmalloc() and returns the allocated buffer. In fact it's called twice,
and neither buffer is freed.

This results in a memory leak as reported by Erhard:
  unreferenced object 0xc00000047081f840 (size 32):
    comm "kwindfarm", pid 203, jiffies 4294880630 (age 5552.877s)
    hex dump (first 32 bytes):
      c8 06 02 7f ff 02 ff 01 fb bf 00 41 00 20 00 00  ...........A. ..
      00 07 89 37 00 a0 00 00 00 00 00 00 00 00 00 00  ...7............
    backtrace:
      [<0000000083f0a65c>] .smu_sat_get_sdb_partition+0xc4/0x2d0 [windfarm_smu_sat]
      [<000000003010fcb7>] .pm112_wf_notify+0x104c/0x13bc [windfarm_pm112]
      [<00000000b958b2dd>] .notifier_call_chain+0xa8/0x180
      [<0000000070490868>] .blocking_notifier_call_chain+0x64/0x90
      [<00000000131d8149>] .wf_thread_func+0x114/0x1a0
      [<000000000d54838d>] .kthread+0x13c/0x190
      [<00000000669b72bc>] .ret_from_kernel_thread+0x58/0x64
  unreferenced object 0xc0000004737089f0 (size 16):
    comm "kwindfarm", pid 203, jiffies 4294880879 (age 5552.050s)
    hex dump (first 16 bytes):
      c4 04 01 7f 22 11 e0 e6 ff 55 7b 12 ec 11 00 00  ...."....U{.....
    backtrace:
      [<0000000083f0a65c>] .smu_sat_get_sdb_partition+0xc4/0x2d0 [windfarm_smu_sat]
      [<00000000b94ef7e1>] .pm112_wf_notify+0x1294/0x13bc [windfarm_pm112]
      [<00000000b958b2dd>] .notifier_call_chain+0xa8/0x180
      [<0000000070490868>] .blocking_notifier_call_chain+0x64/0x90
      [<00000000131d8149>] .wf_thread_func+0x114/0x1a0
      [<000000000d54838d>] .kthread+0x13c/0x190
      [<00000000669b72bc>] .ret_from_kernel_thread+0x58/0x64

Fix it by rearranging the logic so we deal with each buffer
separately, which then makes it easy to free the buffer once we're
done with it.

Fixes: ac171c46667c ("[PATCH] powerpc: Thermal control for dual core G5s")
Cc: stable@vger.kernel.org # v2.6.16+
Reported-by: Erhard F. <erhard_f@mailbox.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Tested-by: Erhard F. <erhard_f@mailbox.org>
Link: https://lore.kernel.org/r/20200423060038.3308530-1-mpe@ellerman.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: dts: s5pv210: Set keep-power-in-suspend for SDHCI1 on Aries

commit 869d42e6eba821905e1a0950623aadafe1a6e6d3 upstream.

SDHCI1 is connected to a BCM4329 WiFi/BT chip which requires
power to be kept over suspend.  As the surrounding hardware supports
this, mark it as such.  This fixes WiFi after a suspend/resume cycle.

Fixes: 170642468a51 ("ARM: dts: s5pv210: Add initial DTS for Samsung Aries based phones")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: dts: at91: sama5d2_ptc_ek: fix vbus pin

commit baa998aecb75c04d62be0a4ab6b724af6d73a0f9 upstream.

The gpio property for the vbus pin doesn't match the pinctrl and is
not correct.

Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Fixes: 42ed535595ec "ARM: dts: at91: introduce the sama5d2 ptc ek board"
Cc: stable@vger.kernel.org # 4.19 and later
Link: https://lore.kernel.org/r/20200401221947.41502-1-ludovic.desroches@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: dts: exynos: Fix GPIO polarity for thr GalaxyS3 CM36651 sensor's bus

commit 8807d356bfea92b0a8f04ce421800ed83400cd22 upstream.

GPIO lines for the CM36651 sensor I2C bus use the normal not the inverted
polarity. This bug has been there since adding the CM36651 sensor by
commit 85cb4e0bd229 ("ARM: dts: add cm36651 light/proximity sensor node
for exynos4412-trats2"), but went unnoticed because the "i2c-gpio"
driver ignored the GPIO polarity specified in the device-tree.

The recent conversion of "i2c-gpio" driver to the new, descriptor based
GPIO API, automatically made it the DT-specified polarity aware, what
broke the CM36651 sensor operation.

Fixes: 85cb4e0bd229 ("ARM: dts: add cm36651 light/proximity sensor node for exynos4412-trats2")
CC: stable@vger.kernel.org # 4.16+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

soc/tegra: pmc: Select GENERIC_PINCONF

commit 5098e2b95e8e6f56266c2d5c180c75917090082a upstream.

I have hit the following build error:
armv7a-hardfloat-linux-gnueabi-ld: drivers/soc/tegra/pmc.o: in function `pinconf_generic_dt_node_to_map_pin':
pmc.c:(.text+0x500): undefined reference to `pinconf_generic_dt_node_to_map'
armv7a-hardfloat-linux-gnueabi-ld: drivers/soc/tegra/pmc.o:(.rodata+0x1f88): undefined reference to `pinconf_generic_dt_free_map'

So SOC_TEGRA_PMC should select GENERIC_PINCONF.

Fixes: 4a37f11c8f57 ("soc/tegra: pmc: Implement pad configuration via pinctrl")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: tegra: Correct PL310 Auxiliary Control Register initialization

commit 35509737c8f958944e059d501255a0bf18361ba0 upstream.

The PL310 Auxiliary Control Register shouldn't have the "Full line of
zero" optimization bit being set before L2 cache is enabled. The L2X0
driver takes care of enabling the optimization by itself.

This patch fixes a noisy error message on Tegra20 and Tegra30 telling
that cache optimization is erroneously enabled without enabling it for
the CPU:

L2C-310: enabling full line of zeros but not enabled in Cortex-A9

Cc: <stable@vger.kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kernel/cpu_pm: Fix uninitted local in cpu_pm

commit b5945214b76a1f22929481724ffd448000ede914 upstream.

cpu_pm_notify() is basically a wrapper of notifier_call_chain().
notifier_call_chain() doesn't initialize *nr_calls to 0 before it
starts incrementing it--presumably it's up to the callers to do this.

Unfortunately the callers of cpu_pm_notify() don't init *nr_calls.
This potentially means you could get too many or two few calls to
CPU_PM_ENTER_FAILED or CPU_CLUSTER_PM_ENTER_FAILED depending on the
luck of the stack.

Let's fix this.

Fixes: ab10023e0088 ("cpu_pm: Add cpu power management notifiers")
Cc: stable@vger.kernel.org
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200504104917.v6.3.I2d44fc0053d019f239527a4e5829416714b7e299@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/fadump: Account for memory_limit while reserving memory

commit 9a2921e5baca1d25eb8d21f21d1e90581a6d0f68 upstream.

If the memory chunk found for reserving memory overshoots the memory
limit imposed, do not proceed with reserving memory. Default behavior
was this until commit 140777a3d8df ("powerpc/fadump: consider reserved
ranges while reserving memory") changed it unwittingly.

Fixes: 140777a3d8df ("powerpc/fadump: consider reserved ranges while reserving memory")
Cc: stable@vger.kernel.org
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/159057266320.22331.6571453892066907320.stgit@hbathini.in.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/fadump: consider reserved ranges while reserving memory

commit 140777a3d8dfdb3d3f20ea7707c0f1c0ce1b0aa5 upstream.

Commit 0962e8004e97 ("powerpc/prom: Scan reserved-ranges node for
memory reservations") enabled support to parse reserved-ranges DT
node and reserve kernel memory falling in these ranges for F/W
purposes. Memory reserved for FADump should not overlap with these
ranges as it could corrupt memory meant for F/W or crash'ed kernel
memory to be exported as vmcore.

But since commit 579ca1a27675 ("powerpc/fadump: make use of memblock's
bottom up allocation mode"), memblock_find_in_range() is being used to
find the appropriate area to reserve memory for FADump, which can't
account for reserved-ranges as these ranges are reserved only after
FADump memory reservation.

With reserved-ranges now being populated during early boot, look out
for these memory ranges while reserving memory for FADump. Without
this change, MPIPL on PowerNV systems aborts with hostboot failure,
when memory reserved for FADump is less than 4096MB.

Fixes: 579ca1a27675 ("powerpc/fadump: make use of memblock's bottom up allocation mode")
Cc: stable@vger.kernel.org
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/158737297693.26700.16193820746269425424.stgit@hbathini.in.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/fadump: use static allocation for reserved memory ranges

commit 02c04e374e176ae3a3f64a682f80702f8d2fb65d upstream.

At times, memory ranges have to be looked up during early boot, when
kernel couldn't be initialized for dynamic memory allocation. In fact,
reserved-ranges look up is needed during FADump memory reservation.
Without accounting for reserved-ranges in reserving memory for FADump,
MPIPL boot fails with memory corruption issues. So, extend memory
ranges handling to support static allocation and populate reserved
memory ranges during early boot.

Fixes: dda9dbfeeb7a ("powerpc/fadump: consider reserved ranges while releasing memory")
Cc: stable@vger.kernel.org
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/158737294432.26700.4830263187856221314.stgit@hbathini.in.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

alpha: fix memory barriers so that they conform to the specification

commit 54505a1e2083fc54cbe8779b97479f969cd30a00 upstream.

The commits cd0e00c10672 and 92d7223a7423 broke boot on the Alpha Avanti
platform. The patches move memory barriers after a write before the write.
The result is that if there's iowrite followed by ioread, there is no
barrier between them.

The Alpha architecture allows reordering of the accesses to the I/O space,
and the missing barrier between write and read causes hang with serial
port and real time clock.

This patch makes barriers confiorm to the specification.

1. We add mb() before readX_relaxed and writeX_relaxed -
   memory-barriers.txt claims that these functions must be ordered w.r.t.
   each other. Alpha doesn't order them, so we need an explicit barrier.
2. We add mb() before reads from the I/O space - so that if there's a
   write followed by a read, there should be a barrier between them.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Fixes: cd0e00c10672 ("alpha: io: reorder barriers to guarantee writeX() and iowriteX() ordering")
Fixes: 92d7223a7423 ("alpha: io: reorder barriers to guarantee writeX() and iowriteX() ordering #2")
Cc: stable@vger.kernel.org # v4.17+
Acked-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Reviewed-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dm crypt: avoid truncating the logical block size

commit 64611a15ca9da91ff532982429c44686f4593b5f upstream.

queue_limits::logical_block_size got changed from unsigned short to
unsigned int, but it was forgotten to update crypt_io_hints() to use the
new type.  Fix it.

Fixes: ad6bf88a6c19 ("block: fix an integer overflow in logical block size")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sparc64: fix misuses of access_process_vm() in genregs32_[sg]et()

commit 142cd25293f6a7ecbdff4fb0af17de6438d46433 upstream.

We do need access_process_vm() to access the target's reg_window.
However, access to caller's memory (storing the result in
genregs32_get(), fetching the new values in case of genregs32_set())
should be done by normal uaccess primitives.

Fixes: ad4f95764040 ([SPARC64]: Fix user accesses in regset code.)
Cc: stable@kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sparc32: fix register window handling in genregs32_[gs]et()

commit cf51e129b96847f969bfb8af1ee1516a01a70b39 upstream.

It needs access_process_vm() if the traced process does not share
mm with the caller.  Solution is similar to what sparc64 does.
Note that genregs32_set() is only ever called with pos being 0
or 32 * sizeof(u32) (the latter - as part of PTRACE_SETREGS
handling).

Cc: stable@kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

gnss: sirf: fix error return code in sirf_probe()

commit 43d7ce70ae43dd8523754b17f567417e0e75dbce upstream.

Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.

This avoids a use-after-free in case the driver is later unbound.

Fixes: d2efbbd18b1e ("gnss: add driver for sirfstar-based receivers")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
[ johan: amend commit message; mention potential use-after-free ]
Cc: stable <stable@vger.kernel.org> # 4.19
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pinctrl: samsung: Save/restore eint_mask over suspend for EINT_TYPE GPIOs

commit f354157a7d184db430c1a564c506434e33b1bec5 upstream.

Currently, for EINT_TYPE GPIOs, the CON and FLTCON registers
are saved and restored over a suspend/resume cycle.  However, the
EINT_MASK registers are not.

On S5PV210 at the very least, these registers are not retained over
suspend, leading to the interrupts remaining masked upon resume and
therefore no interrupts being triggered for the device.  There should
be no effect on any SoCs that do retain these registers as theoretically
we would just be re-writing what was already there.

Fixes: 7ccbc60cd9c2 ("pinctrl: exynos: Handle suspend/resume of GPIO EINT registers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pinctrl: samsung: Correct setting of eint wakeup mask on s5pv210

commit b577a279914085c6b657c33e9f39ef56d96a3302 upstream.

Commit a8be2af0218c ("pinctrl: samsung: Write external wakeup interrupt
mask") started writing the eint wakeup mask from the pinctrl driver.
Unfortunately, it made the assumption that the private retention data
was always a regmap while in the case of s5pv210 it is a raw pointer
to the clock base (as the eint wakeup mask not in the PMU as with newer
Exynos platforms).

Fixes: a8be2af0218c ("pinctrl: samsung: Write external wakeup interrupt mask")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

power: supply: core: fix memory leak in HWMON error path

commit 1d7a7128a2e9e1f137c99b0a44e94d70a77343e3 upstream.

In function power_supply_add_hwmon_sysfs(), psyhw->props is
allocated by bitmap_zalloc(). But this pointer is not deallocated
when devm_add_action fail,  which lead to a memory leak bug. To fix
this, we replace devm_add_action with devm_add_action_or_reset.

Cc: stable@kernel.org
Fixes: e67d4dfc9ff19 ("power: supply: Add HWMON compatibility layer")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

power: supply: core: fix HWMON temperature labels

commit 6b20464ad9fb5fd76ef6f219ce62156aa9639dcc upstream.

tempX_label files are swapped compared to what
power_supply_hwmon_temp_to_property() uses. Make them match.

Cc: stable@vger.kernel.org
Fixes: e67d4dfc9ff1 ("power: supply: Add HWMON compatibility layer")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

power: vexpress: add suppress_bind_attrs to true

commit 73174acc9c75960af2daa7dcbdb9781fc0d135cb upstream.

Make sure that the POWER_RESET_VEXPRESS driver won't have bind/unbind
attributes available via the sysfs, so lets be explicit here and use
".suppress_bind_attrs = true" to prevent userspace from doing something
silly.

Link: https://lore.kernel.org/r/20200527112608.3886105-2-anders.roxell@linaro.org
Cc: stable@vger.kernel.org
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

EDAC/amd64: Add AMD family 17h model 60h PCI IDs

commit b6bea24d41519e8c31e4798f1c1a3f67e540c5d0 upstream.

Add support for AMD Renoir (4000-series Ryzen CPUs).

Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Yazen Ghannam <yazen.ghannam@amd.com>
Link: https://lkml.kernel.org/r/20200510204842.2603-4-amonakov@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hwmon: (k10temp) Add AMD family 17h model 60h PCI match

commit 279f0b3a4b80660fba6faadc2ca2fa426bf3f7e9 upstream.

Add support for retrieving Tdie and Tctl on AMD Renoir (4000-series
Ryzen CPUs).

It appears SMU offsets for reading current/voltage and CCD temperature
have changed for this generation (reads from currently used offsets
yield zeros), so those features cannot be enabled so trivially.

Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lkml.kernel.org/r/20200510204842.2603-3-amonakov@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

igb: Report speed and duplex as unknown when device is runtime suspended

commit 165ae7a8feb53dc47fb041357e4b253bfc927cf9 upstream.

igb device gets runtime suspended when there's no link partner. We can't
get correct speed under that state:
$ cat /sys/class/net/enp3s0/speed
1000

In addition to that, an error can also be spotted in dmesg:
[  385.991957] igb 0000:03:00.0 enp3s0: PCIe link lost

Since device can only be runtime suspended when there's no link partner,
we can skip reading register and let the following logic set speed and
duplex with correct status.

The more generic approach will be wrap get_link_ksettings() with begin()
and complete() callbacks. However, for this particular issue, begin()
calls igb_runtime_resume() , which tries to rtnl_lock() while the lock
is already hold by upper ethtool layer.

So let's take this approach until the igb_runtime_resume() no longer
needs to hold rtnl_lock.

CC: stable <stable@vger.kernel.org>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clk: mediatek: assign the initial value to clk_init_data of mtk_mux

commit 571cfadcc628dd5591444f7289e27445ea732f4c upstream.

When some new clock supports are introduced, e.g. [1]
it might lead to an error although it should be NULL because
clk_init_data is on the stack and it might have random values
if using without initialization.
Add the missing initial value to clk_init_data.

[1] https://android-review.googlesource.com/c/kernel/common/+/1278046

Fixes: a3ae549917f1 ("clk: mediatek: Add new clkmux register API")
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1590560749-29136-1-git-send-email-weiyi.lu@mediatek.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: ov5640: fix use of destroyed mutex

commit bfcba38d95a0aed146a958a84a2177af1459eddc upstream.

v4l2_ctrl_handler_free() uses hdl->lock, which in ov5640 driver is set
to sensor's own sensor->lock. In ov5640_remove(), the driver destroys the
sensor->lock first, and then calls v4l2_ctrl_handler_free(), resulting
in the use of the destroyed mutex.

Fix this by calling moving the mutex_destroy() to the end of the cleanup
sequence, as there's no need to destroy the mutex as early as possible.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@vger.kernel.org # v4.14+
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

b43_legacy: Fix connection problem with WPA3

commit 6a29d134c04a8acebb7a95251acea7ad7abba106 upstream.

Since the driver was first introduced into the kernel, it has only
handled the ciphers associated with WEP, WPA, and WPA2. It fails with
WPA3 even though mac80211 can handle those additional ciphers in software,
b43legacy did not report that it could handle them. By setting MFP_CAPABLE using
ieee80211_set_hw(), the problem is fixed.

With this change, b43legacy will handle the ciphers it knows in hardware,
and let mac80211 handle the others in software. It is not necessary to
use the module parameter NOHWCRYPT to turn hardware encryption off.
Although this change essentially eliminates that module parameter,
I am choosing to keep it for cases where the hardware is broken,
and software encryption is required for all ciphers.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200526155909.5807-3-Larry.Finger@lwfinger.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

b43: Fix connection problem with WPA3

commit 75d057bda1fbca6ade21378aa45db712e5f7d962 upstream.

Since the driver was first introduced into the kernel, it has only
handled the ciphers associated with WEP, WPA, and WPA2. It fails with
WPA3 even though mac80211 can handle those additional ciphers in software,
b43 did not report that it could handle them. By setting MFP_CAPABLE using
ieee80211_set_hw(), the problem is fixed.

With this change, b43 will handle the ciphers it knows in hardware,
and let mac80211 handle the others in software. It is not necessary to
use the module parameter NOHWCRYPT to turn hardware encryption off.
Although this change essentially eliminates that module parameter,
I am choosing to keep it for cases where the hardware is broken,
and software encryption is required for all ciphers.

Reported-and-tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200526155909.5807-2-Larry.Finger@lwfinger.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

b43legacy: Fix case where channel status is corrupted

commit ec4d3e3a054578de34cd0b587ab8a1ac36f629d9 upstream.

This patch fixes commit 75388acd0cd8 ("add mac80211-based driver for
legacy BCM43xx devices")

In https://bugzilla.kernel.org/show_bug.cgi?id=207093, a defect in
b43legacy is reported. Upon testing, thus problem exists on PPC and
X86 platforms, is present in the oldest kernel tested (3.2), and
has been present in the driver since it was first added to the kernel.

The problem is a corrupted channel status received from the device.
Both the internal card in a PowerBook G4 and the PCMCIA version
(Broadcom BCM4306 with PCI ID 14e4:4320) have the problem. Only Rev, 2
(revision 4 of the 802.11 core) of the chip has been tested. No other
devices using b43legacy are available for testing.

Various sources of the problem were considered. Buffer overrun and
other sources of corruption within the driver were rejected because
the faulty channel status is always the same, not a random value.
It was concluded that the faulty data is coming from the device, probably
due to a firmware bug. As that source is not available, the driver
must take appropriate action to recover.

At present, the driver reports the error, and them continues to process
the bad packet. This is believed that to be a mistake, and the correct
action is to drop the correpted packet.

Fixes: 75388acd0cd8 ("add mac80211-based driver for legacy BCM43xx devices")
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-and-tested by: F. Erhard <erhard_f@mailbox.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200407190043.1686-1-Larry.Finger@lwfinger.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Bluetooth: hci_bcm: fix freeing not-requested IRQ

commit 81bd5d0c62437c02caac6b3f942fcda874063cb0 upstream.

When BT module can't be initialized, but it has an IRQ, unloading
the driver WARNs when trying to free not-yet-requested IRQ. Fix it by
noting whether the IRQ was requested.

WARNING: CPU: 2 PID: 214 at kernel/irq/devres.c:144 devm_free_irq+0x49/0x4ca
[...]
WARNING: CPU: 2 PID: 214 at kernel/irq/manage.c:1746 __free_irq+0x8b/0x27c
Trying to free already-free IRQ 264
Modules linked in: hci_uart(-) btbcm bluetooth ecdh_generic ecc libaes
CPU: 2 PID: 214 Comm: rmmod Tainted: G        W         5.6.1mq-00044-ga5f9ea098318-dirty #928
[...]
[<b016aefb>] (devm_free_irq) from [<af8ba1ff>] (bcm_close+0x97/0x118 [hci_uart])
[<af8ba1ff>] (bcm_close [hci_uart]) from [<af8b736f>] (hci_uart_unregister_device+0x33/0x3c [hci_uart])
[<af8b736f>] (hci_uart_unregister_device [hci_uart]) from [<b035930b>] (serdev_drv_remove+0x13/0x20)
[<b035930b>] (serdev_drv_remove) from [<b037093b>] (device_release_driver_internal+0x97/0x118)
[<b037093b>] (device_release_driver_internal) from [<b0370a0b>] (driver_detach+0x2f/0x58)
[<b0370a0b>] (driver_detach) from [<b036f855>] (bus_remove_driver+0x41/0x94)
[<b036f855>] (bus_remove_driver) from [<af8ba8db>] (bcm_deinit+0x1b/0x740 [hci_uart])
[<af8ba8db>] (bcm_deinit [hci_uart]) from [<af8ba86f>] (hci_uart_exit+0x13/0x30 [hci_uart])
[<af8ba86f>] (hci_uart_exit [hci_uart]) from [<b01900bd>] (sys_delete_module+0x109/0x1d0)
[<b01900bd>] (sys_delete_module) from [<b0101001>] (ret_fast_syscall+0x1/0x5a)
[...]

Cc: stable@vger.kernel.org
Fixes: 6cc4396c8829 ("Bluetooth: hci_bcm: Add wake-up capability")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250: Avoid error message on reprobe

commit e0a851fe6b9b619527bd928aa93caaddd003f70c upstream.

If the call to uart_add_one_port() in serial8250_register_8250_port()
fails, a half-initialized entry in the serial_8250ports[] array is left
behind.

A subsequent reprobe of the same serial port causes that entry to be
reused.  Because uart->port.dev is set, uart_remove_one_port() is called
for the half-initialized entry and bails out with an error message:

bcm2835-aux-uart 3f215040.serial: Removing wrong port: (null) != (ptrval)

The same happens on failure of mctrl_gpio_init() since commit
4a96895f74c9 ("tty/serial/8250: use mctrl_gpio helpers").

Fix by zeroing the uart->port.dev pointer in the probe error path.

The bug was introduced in v2.6.10 by historical commit befff6f5bf5f
("[SERIAL] Add new port registration/unregistration functions."):
https://git.kernel.org/tglx/history/c/befff6f5bf5f

The commit added an unconditional call to uart_remove_one_port() in
serial8250_register_port().  In v3.7, commit 835d844d1a28 ("8250_pnp:
do pnp probe before legacy probe") made that call conditional on
uart->port.dev which allows me to fix the issue by zeroing that pointer
in the error path.  Thus, the present commit will fix the problem as far
back as v3.7 whereas still older versions need to also cherry-pick
835d844d1a28.

Fixes: 835d844d1a28 ("8250_pnp: do pnp probe before legacy probe")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v2.6.10
Cc: stable@vger.kernel.org # v2.6.10: 835d844d1a28: 8250_pnp: do pnp probe before legacy
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/b4a072013ee1a1d13ee06b4325afb19bda57ca1b.1589285873.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: cedrus: Program output format during each run

commit a8876c22eab9a871834f85de83e98bbf7e6e264d upstream.

Previously, the output format was programmed as part of the ioctl()
handler. However, this has two problems:

  1) If there are multiple active streams with different output
     formats, the hardware will use whichever format was set last
     for both streams. Similarly, an ioctl() done in an inactive
     context will wrongly affect other active contexts.
  2) The registers are written while the device is not actively
     streaming. To enable runtime PM tied to the streaming state,
     all hardware access needs to be moved inside cedrus_device_run().

The call to cedrus_dst_format_set() is now placed just before the
codec-specific callback that programs the hardware.

Cc: <stable@vger.kernel.org>
Fixes: 50e761516f2b ("media: platform: Add Cedrus VPU decoder driver")
Suggested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Suggested-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: go7007: fix a miss of snd_card_free

commit 9453264ef58638ce8976121ac44c07a3ef375983 upstream.

go7007_snd_init() misses a snd_card_free() in an error path.
Add the missed call to fix it.

Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Cc: Salvatore Bonaccorso <carnil@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

carl9170: remove P2P_GO support

commit b14fba7ebd04082f7767a11daea7f12f3593de22 upstream.

This patch follows up on a bug-report by Frank Schäfer that
discovered P2P GO wasn't working with wpa_supplicant.
This patch removes part of the broken P2P GO support but
keeps the vif switchover code in place.

Cc: <stable@vger.kernel.org>
Link: <https://lkml.kernel.org/r/3a9d86b6-744f-e670-8792-9167257edef8@googlemail.com>
Reported-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200425092811.9494-1-chunkeey@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

e1000e: Relax condition to trigger reset for ME workaround

commit d601afcae2febc49665008e9a79e701248d56c50 upstream.

It's an error if the value of the RX/TX tail descriptor does not match
what was written. The error condition is true regardless the duration
of the interference from ME. But the driver only performs the reset if
E1000_ICH_FWSM_PCIM2PCI_COUNT (2000) iterations of 50us delay have
transpired. The extra condition can lead to inconsistency between the
state of hardware as expected by the driver.

Fix this by dropping the check for number of delay iterations.

While at it, also make __ew32_prepare() static as it's not used
anywhere else.

CC: stable <stable@vger.kernel.org>
Signed-off-by: Punit Agrawal <punit1.agrawal@toshiba.co.jp>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

e1000e: Disable TSO for buffer overrun workaround

commit f29801030ac67bf98b7a65d3aea67b30769d4f7c upstream.

Commit b10effb92e27 ("e1000e: fix buffer overrun while the I219 is
processing DMA transactions") imposes roughly 30% performance penalty.

The commit log states that "Disabling TSO eliminates performance loss
for TCP traffic without a noticeable impact on CPU performance", so
let's disable TSO by default to regain the loss.

CC: stable <stable@vger.kernel.org>
Fixes: b10effb92e27 ("e1000e: fix buffer overrun while the I219 is processing DMA transactions")
BugLink: https://bugs.launchpad.net/bugs/1802691
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: Program MPS for RCiEP devices

commit aa0ce96d72dd2e1b0dfd0fb868f82876e7790878 upstream.

Root Complex Integrated Endpoints (RCiEPs) do not have an upstream bridge,
so pci_configure_mps() previously ignored them, which may result in reduced
performance.

Instead, program the Max_Payload_Size of RCiEPs to the maximum supported
value (unless it is limited for the PCIE_BUS_PEER2PEER case).  This also
affects the subsequent programming of Max_Read_Request_Size because Linux
programs MRRS based on the MPS value.

Fixes: 9dae3a97297f ("PCI: Move MPS configuration check to pci_configure_device()")
Link: https://lore.kernel.org/r/1585343775-4019-1-git-send-email-ashok.raj@intel.com
Tested-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ima: Set again build_ima_appraise variable

[ Upstream commit b59fda449cf07f2db3be3a67142e6c000f5e8d79 ]

After adding the new add_rule() function in commit c52657d93b05
("ima: refactor ima_init_policy()"), all appraisal flags are added to the
temp_ima_appraise variable. Revert to the previous behavior instead of
removing build_ima_appraise, to benefit from the protection offered by
__ro_after_init.

The mentioned commit introduced a bug, as it makes all the flags
modifiable, while build_ima_appraise flags can be protected with
__ro_after_init.

Cc: stable@vger.kernel.org # 5.0.x
Fixes: c52657d93b05 ("ima: refactor ima_init_policy()")
Co-developed-by: Roberto Sassu <roberto.sassu@huawei.com>
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Signed-off-by: Krzysztof Struczynski <krzysztof.struczynski@huawei.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ima: Remove redundant policy rule set in add_rules()

[ Upstream commit 6ee28442a465ab4c4be45e3b15015af24b1ba906 ]

Function ima_appraise_flag() returns the flag to be set in
temp_ima_appraise depending on the hook identifier passed as an argument.
It is not necessary to set the flag again for the POLICY_CHECK hook.

Signed-off-by: Krzysztof Struczynski <krzysztof.struczynski@huawei.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86/amd_nb: Add AMD family 17h model 60h PCI IDs

[ Upstream commit a4e91825d7e1252f7cba005f1451e5464b23c15d ]

Add PCI IDs for AMD Renoir (4000-series Ryzen CPUs). This is necessary
to enable support for temperature sensors via the k10temp module.

Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Yazen Ghannam <yazen.ghannam@amd.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lkml.kernel.org/r/20200510204842.2603-2-amonakov@ispras.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>

serial: 8250_pci: Move Pericom IDs to pci_ids.h

[ Upstream commit 62a7f3009a460001eb46984395280dd900bc4ef4 ]

Move the IDs to pci_ids.h so it can be used by next patch.

Link: https://lore.kernel.org/r/20200508065343.32751-1-kai.heng.feng@canonical.com
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: Add Loongson vendor ID

[ Upstream commit 9acb9fe18d863aacc99948963f8d5d447dc311be ]

Add the Loongson vendor ID to pci_ids.h to be used by the controller
driver in the future.

The Loongson vendor ID can be found at the following link:
https://git.kernel.org/pub/scm/utils/pciutils/pciutils.git/tree/pci.ids

Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>