Toke Høiland-Jørgensen [Mon, 11 Feb 2019 16:47:47 +0000 (18:47 +0200)]
ath9k: Switch to mac80211 TXQ scheduling and airtime APIs
This moves the ath9k driver to use the mac80211 TXQ scheduling and
airtime accounting APIs, removing the corresponding state tracking
inside the driver.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
[rmanohar@codeaurora.org: fixed checkpatch error and warnings]
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Kalle Valo [Mon, 11 Feb 2019 16:47:01 +0000 (18:47 +0200)]
ath10k: fix line length warning in ath10k_ce_alloc_dest_ring()
Commit
750afb08ca71 ("cross-tree: phase out dma_zalloc_coherent()") introduced
a new checkpatch warning:
drivers/net/wireless/ath/ath10k/ce.c:1602: line over 90 characters
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rakesh Pillai [Fri, 8 Feb 2019 13:50:24 +0000 (15:50 +0200)]
ath10k: fix shadow register implementation for WCN3990
WCN3990 supports shadow registers write operation support
for copy engine for regular operation in powersave mode.
Since WCN3990 is a 64-bit target, the shadow register
implementation needs to be done in the copy engine handlers
for 64-bit target. Currently the shadow register implementation
is present in the 32-bit target handlers of copy engine.
Fix the shadow register copy engine write operation
implementation for 64-bit target(WCN3990).
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Fixes:
b7ba83f7c414 ("ath10k: add support for shadow register for WNC3990")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rakesh Pillai [Fri, 8 Feb 2019 13:50:10 +0000 (15:50 +0200)]
ath10k: enable Factory Test Mode for WCN3990
The support to put WCN3990 firmware into Factory
test mode is not present currently. The WCN3990
firmware can operate in Factory test mode based
on the mode it receives in the wlan enable message
from the host driver.
When the host driver is started in testmode send
the operating mode as UTF mode, to the WCN3990
firmware, in the wlan enable message to start the
firmware in Factory test mode.
Tested on: WCN3990
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Brian Norris [Fri, 8 Feb 2019 12:55:38 +0000 (14:55 +0200)]
ath10k: pci: use mutex for diagnostic window CE polling
The DIAG copy engine is only used via polling, but it holds a spinlock
with softirqs disabled. Each iteration of our read/write loops can
theoretically take 20ms (two 10ms timeout loops), and this loop can be
run an unbounded number of times while holding the spinlock -- dependent
on the request size given by the caller.
As of commit
39501ea64116 ("ath10k: download firmware via diag Copy
Engine for QCA6174 and QCA9377."), we transfer large chunks of firmware
memory using this mechanism. With large enough firmware segments, this
becomes an exceedingly long period for disabling soft IRQs. For example,
with a 500KiB firmware segment, in testing QCA6174A, I see 200 loop
iterations of about 50-100us each, which can total about 10-20ms.
In reality, we don't really need to block softirqs for this duration.
The DIAG CE is only used in polling mode, and we only need to hold
ce_lock to make sure any CE bookkeeping is done without screwing up
another CE. Otherwise, we only need to ensure exclusion between
ath10k_pci_diag_{read,write}_mem() contexts.
This patch moves to use fine-grained locking for the shared ce_lock,
while adding a new mutex just to ensure mutual exclusion of diag
read/write operations.
Tested on QCA6174A, firmware version WLAN.RM.4.4.1-00132-QCARMSWPZ-1.
Fixes:
39501ea64116 ("ath10k: download firmware via diag Copy Engine for QCA6174 and QCA9377.")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Govind Singh [Fri, 8 Feb 2019 12:55:35 +0000 (14:55 +0200)]
ath10k: request credit report if flow control enabled on ep
FW credit flow control is enabled for only WMI ctrl
service(CE3) but credit update is requested unconditionally
on all HTC services as part of HTC tx in CE3/CE0/CE4.
This is causing WOW failure as FW is not expecting credit
report request on other end-points(CE0/CE4).
Request credit report only on those endpoints where
credit flow control is enabled.
Testing:
Tested on WCN3990 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Govind Singh [Fri, 8 Feb 2019 12:55:33 +0000 (14:55 +0200)]
ath10k: disable interface pause wow config for integrated chipset
wow pause iface config controls the PCI D0/D3-WOW cases for pcie
bus state. Firmware does not expects WOW_IFACE_PAUSE_ENABLED config
for bus/link that cannot be suspended ex:snoc and does not trigger
common subsystem shutdown.
Disable interface pause wow config for integrated chipset(WCN3990)
for correct WOW configuration in the firmware.
Testing:
Tested on WCN3990 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Govind Singh [Fri, 8 Feb 2019 12:55:31 +0000 (14:55 +0200)]
ath10k: enable bus layer suspend/resume for WCN3990
Register snoc bus layer suspend/resume PM ops and configure
the wakeup source(CE2) for the device.
Testing:
Tested on WCN3990 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Christian Lamparter [Fri, 8 Feb 2019 12:55:28 +0000 (14:55 +0200)]
ath10k: implement set_base_macaddr to fix rx-bssid mask in multiple APs conf
Many integrated QCA9984 WiFis in various IPQ806x platform routers
from various vendors (Netgear R7800, ZyXEL NBG6817, TP-LINK C2600,
etc.) have either blank, bogus or non-unique MAC-addresses in
their calibration data.
As a result, OpenWrt utilizes a discouraged binary calibration data
patching method that allows to modify the device's MAC-addresses right
at the source. This is because the ath10k' firmware extracts the MAC
address from the supplied radio/calibration data and issues a response
to the ath10k linux driver. Which was designed to take the main MAC in
ath10k_wmi_event_ready().
Part of the "setting an alternate MAC" issue was already tackled by a
patch from Brian Norris:
commit
9d5804662ce1
("ath10k: retrieve MAC address from system firmware if provided")
by allowing the option to specify an alternate MAC-address with the
established device_get_mac_address() function which extracts the right
address from DeviceTree/fwnode mac-address or local-mac-address
properties and saves it for later.
However, Ben Greear noted that the Qualcomm's ath10k firmware is liable
to not properly calculate its rx-bssid mask in this case. This can cause
issues in the popluar "multiple AP with a single ath10k instance"
configurations.
To improve MAC address handling, Felix Fietkau suggested to call
pdev_set_base_macaddr_cmdid before bringing up the first vif and
use the first vif MAC address there. Which is in ath10k_core_start().
This patch implement Felix Fietkau's request to
"call pdev_set_base_macaddr_cmdid before bringing up the first vif".
The pdev_set_base_macaddr_cmdid is already declared for all devices
and version. The driver just needed the support code for this
function.
Tested on:
QCA9880/CUS223, firmwares: 10.2.4.13-2, 10.2.4.70.44, 10.2.4-1.0-00041
QCA9887/MR33 firmware:10.2.4-1.0-00033
QCA4019/RT-AC58U firmware: 10.4-3.4-00104, 10.4-3.5.3-00057
QCA9984/R7800 firmware: Candela Technologies (CT) Firmware
BugLink: https://lists.openwrt.org/pipermail/openwrt-devel/2018-November/014595.html
Fixes:
9d5804662ce1 ("ath10k: retrieve MAC address from system firmware if provided")
Cc: Brian Norris <briannorris@chromium.org>
Cc: Ben Greear <greearb@candelatech.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Abhishek Ambure [Fri, 8 Feb 2019 12:55:26 +0000 (14:55 +0200)]
ath10k: update GCMP & GCMP-256 cipher suite number for WCN3990
TLV based firmware ex. QCA6174, WCN3990 expects key cipher value
set to 9 while non-TLV firmware expects key cipher value set to 8
for enabling GCMP and GCMP-256 cipher suites.
To fix this problem, attach the key cipher suite values based on
wmi version.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Abhishek Ambure [Fri, 8 Feb 2019 12:55:23 +0000 (14:55 +0200)]
ath10k: assign 'n_cipher_suites = 11' for WCN3990 to enable WPA3
Hostapd uses CCMP, GCMP & GCMP-256 as 'wpa_pairwise' option to run WPA3.
In WCN3990 firmware cipher suite numbers 9 to 11 are for CCMP,
GCMP & GCMP-256.
To enable CCMP, GCMP & GCMP-256 cipher suites in WCN3990 firmware,
host sets 'n_cipher_suites = 11' while initializing hardware parameters.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Kalle Valo [Fri, 8 Feb 2019 12:14:35 +0000 (14:14 +0200)]
Merge git://git./linux/kernel/git/kvalo/wireless-drivers.git
The series "[PATCH 0/2] mt76x0: initialize per-channel max_power" depends on
commit
d04ca383860b ("mt76x0u: fix suspend/resume"), so merge wireless-drivers
into wireless-drivers-next to get that.
Kalle Valo [Fri, 8 Feb 2019 12:10:35 +0000 (14:10 +0200)]
Merge ath-next from git://git./linux/kernel/git/kvalo/ath.git
ath.git patches for 5.1. Major changes:
ath10k
* change QMI interface to support the new (and backwards incompatible)
interface from HL3.1 and used in recent HL2.0 branch firmware releases
ath
* add new country codes for US
Stanislaw Gruszka [Wed, 6 Feb 2019 14:34:16 +0000 (15:34 +0100)]
mt76x0u: fix suspend/resume
We need to reset MCU and do other initializations on resume otherwise
MT7610U device will fail to initialize, what cause system hung due to
USB requests timeouts.
Patch fixes 4.19 -> 4.20 regression.
Cc: stable@vger.kernel.org # 4.20+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Oever Gonzalez [Sat, 26 Jan 2019 16:30:19 +0000 (17:30 +0100)]
ath: regd: add extra US coutry codes
This patch adds several country codes to the regd.h and regd_common.h
files in order to support devices like the Linksys EA6350v3, whose
country codes are not present in the original list. Without this patch,
all devices whose manufacturer programmed any of these code in their
EEPROM will not work.
The values for CTRY_UNITED_STATES2 and CTRY_UNITED_STATES3 were taken
from a post by Sven Eckelmann <sven.eckelmann@openmesh.com>:
<http://lists.infradead.org/pipermail/ath10k/2017-August/010014.html>
Signed-off-by: Oever Gonzalez <notengobattery@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Zhiwei Jiang [Tue, 22 Jan 2019 16:30:33 +0000 (00:30 +0800)]
ath: move spin_lock_bh to spin_lock in tasklet
as you are already in a tasklet, it is unnecessary to call
spin_lock_bh, because softirq already disable BH.
Signed-off-by: Zhiwei Jiang <qq282012236@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Greg Kroah-Hartman [Thu, 31 Jan 2019 13:16:25 +0000 (14:16 +0100)]
ath9k: do not return invalid pointers as a *dentry
When calling debugfs functions, they can now return error values if
something went wrong. If that happens, return a NULL as a *dentry to
the relay core instead of passing it an illegal pointer.
The relay core should be able to handle an illegal pointer, but add this
check to be safe.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Surabhi Vishnoi [Fri, 1 Feb 2019 05:36:30 +0000 (11:06 +0530)]
ath10k: fill tx_duration for each peer in Tx stats per STA
Firmware sends the tx_duration for each in HTT_T2H_MSG_TYPE_PEER_STATS
msg. Fill the tx_duration sent by firmware in the tx stats information
per STA.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1,
WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Surabhi Vishnoi [Fri, 1 Feb 2019 05:34:22 +0000 (11:04 +0530)]
ath10k: add a condition to fill the LDPC capability correctly
The firmware advertises the LDPC support information for HT in
HT capability info in the wmi service ready event. To provide
granularity, firmware now advertises WMI_HT_CAP_RX_LDPC and
WMI_HT_CAP_TX_LDPC separately. To support LDPC, host should
also check for WMI_HT_CAP_RX_LDPC and WMI_HT_CAP_TX_LDPC in HT
capabilities.
Add a condition to existing logic in host to know whether firmware
supports LDPC or not.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1,
WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Alagu Sankar [Fri, 1 Feb 2019 02:17:09 +0000 (10:17 +0800)]
ath10k: reduce transmit msdu count
Reduce the transmit MSDU count for SDIO, to match with the descriptors
as used by the firmware. This also acts as a high watermark level for
transmit. Too many packets to the firmware results in transmit overflow
interrupt.
It only affect SDIO chip, it will not cause functionaly changes to
other hardware.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Greg Kroah-Hartman [Thu, 31 Jan 2019 13:15:56 +0000 (14:15 +0100)]
ath10k: do not return invalid pointers as a *dentry
When calling debugfs functions, they can now return error values if
something went wrong. If that happens, return a NULL as a *dentry to
the relay core instead of passing it an illegal pointer.
The relay core should be able to handle an illegal pointer, but add this
check to be safe.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: ath10k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
YueHaibing [Wed, 30 Jan 2019 03:09:00 +0000 (11:09 +0800)]
ath10k: snoc: remove set but not used variable 'ar_snoc'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/ath10k/snoc.c: In function 'ath10k_snoc_tx_pipe_cleanup':
drivers/net/wireless/ath/ath10k/snoc.c:681:22: warning:
variable 'ar_snoc' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Brian Norris [Tue, 29 Jan 2019 23:14:48 +0000 (15:14 -0800)]
ath10k: sdio: add .owner field
sdio_register_driver() doesn't do this for us, unlike (for example)
platform_driver_register(). This is important for helping track
module-to-device relationships.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wen Gong [Tue, 29 Jan 2019 12:03:12 +0000 (20:03 +0800)]
ath10k: change swap mail box check after htc ready
The swap box flag of firmware is not set before htc ready, then it
will not set swap box flag in ath10k driver, and it will let swap
box setting not same between firmware and ath10k driver, then it
will trigger firmware assert failure.
Check the flag and set swap box after htc ready will fix the firmware
assert failure.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rakesh Pillai [Tue, 29 Jan 2019 09:26:07 +0000 (14:56 +0530)]
ath10k: fix hw-restart crash inject mode for WCN3990
The hw-restart crash inject mode is a special mode, where
there is no crash generated in the firmware, but instead
the driver restarts the firmware. In order to restart WCN3990
firmware, the driver needs to send qmi_wlan_disable message
followed by the qmi_wlan_enable message to the WCN3990 firmware.
Currently the qmi_wlan_disable message is not sent to
the WCN3990 firmware when hw-restart crash is injected,
which causes the firmware to crash when the driver sends
qmi_wlan_enable message during ath10k_restart.
Send qmi_wlan_disable to the WCN3990 firmware when the
hw-restart crash is injected via debugfs.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rakesh Pillai [Fri, 25 Jan 2019 04:21:06 +0000 (09:51 +0530)]
ath10k: fix dma unmap direction for management frames
The management frames transmitted are dma mapped with
direction TO_DEVICE, but incorrectly mapped with
direction FROM_DEVICE during tx complete and error cases.
Fix the direction of dma during dma unmap of the
transmitted management frames.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Fixes:
38a1390e02b7 ("ath10k: dma unmap mgmt tx buffer if wmi cmd send fails")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rakesh Pillai [Fri, 25 Jan 2019 04:10:02 +0000 (09:40 +0530)]
ath10k: Enable bundle tx compl for management frames in WCN3990
WCN3990 sends tx completion of multiple management
frames bundled together in a single event, if the
host driver exposes the support to handle this
bundled tx completion event. This reduces the number
of WMI events which are sent to the host driver by
the target.
Set the BUNDLE_TX_COMPL flag in the host capability
flags when host sends the wmi init command, to indicate
the host capability to handle bundled tx completion for
management frames.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rakesh Pillai [Fri, 25 Jan 2019 04:10:01 +0000 (09:40 +0530)]
ath10k: Handle bundled tx completion for management frames
WCN3990 supports sending tx completion for multiple
management frames bundled together in a single event.
Add support to handle the bundled tx completion
event for WCN3990.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Govind Singh [Mon, 4 Feb 2019 11:55:55 +0000 (17:25 +0530)]
ath10k: update HOST capability qmi message
HOST capability interface data structures are updated
in HL3.1 fw version. Update the qmi host capability
members for compatibility across different firmware
versions.
Since this change breaks backward compatibility with
HL2.0 fw, HL2.0 fw upgrade to WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
or later version is required.
Testing:
Tested on QCS404 platform(WCN3990 HW).
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1,
WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Kalle Valo [Thu, 7 Feb 2019 09:34:26 +0000 (11:34 +0200)]
Merge tag 'iwlwifi-next-for-kalle-2019-02-04' of git://git./linux/kernel/git/iwlwifi/iwlwifi-next
Third batch of iwlwifi patches intended for v5.1
* Work on the new debugging infrastructure continues;
* HE radiotap;
* Support for new FW version 44;
* A couple of new FW API changes;
* A bunch of fixes for static analyzer reported issues;
* General bugfixes;
* Other cleanups and small fixes;
Christian Lamparter [Tue, 5 Feb 2019 21:20:09 +0000 (22:20 +0100)]
net: emac: remove IBM_EMAC_RX_SKB_HEADROOM
The EMAC driver had a custom IBM_EMAC_RX_SKB_HEADROOM
Kconfig option that reserved additional skb headroom for RX.
This patch removes the option and migrates the code
to use napi_alloc_skb() and netdev_alloc_skb_ip_align()
in its place.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Tue, 5 Feb 2019 19:41:37 +0000 (20:41 +0100)]
net: phy: improve genphy_c45_read_link
Let's make genphy_c45_read_link behave the same as genphy_update_link
and set phydev->link in the function directly. This allows to simplify
the callers. In addition don't check further devices once we detect
that at least one device reports link as down.
v2:
- remove an unused variable
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ilias Apalodimas [Tue, 5 Feb 2019 12:15:20 +0000 (14:15 +0200)]
net: stmmac: fix ptp timestamping on Rx on gmac4
The current driver only enables Pdelay_Req and Pdelay_Resp when
HWTSTAMP_FILTER_PTP_V2_EVENT, HWTSTAMP_FILTER_PTP_V1_L4_EVENT or
HWTSTAMP_FILTER_PTP_V2_L4_EVENT is requested. This results in ptp sync on
slave mode to report 'received SYNC without timestamp' when using ptp4l.
Although the hardware can support Sync, Pdelay_Req and Pdelay_resp by
setting bit14 annd bits 17/16 to 01 this leaves Delay_Req timestamps out.
Fix this by enabling all event and general messages timestamps.
This includes SYNC, Follow_Up, Delay_Req, Delay_Resp, Pdelay_Req,
Pdelay_Resp and Pdelay_Resp_Follow_Up messages.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Tested-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Miquel Raynal [Tue, 5 Feb 2019 11:07:28 +0000 (12:07 +0100)]
net: dsa: mv88e6xxx: Prevent suspend to RAM
On one hand, the mv88e6xxx driver has a work queue called in loop
which will attempt register accesses after MDIO bus suspension, that
entirely freezes the platform during suspend.
On the other hand, the DSA core is not ready yet to support suspend to
RAM operation because so far there is no way to recover reliably the
switch configuration.
To avoid the kernel to freeze when suspending with a switch driven by
the mv88e6xxx driver, we choose to prevent the driver suspension and
in the same way, the whole platform.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 7 Feb 2019 01:00:15 +0000 (17:00 -0800)]
Merge branch 'for_net-next-5.1/rds-tos-v4' of git://git./linux/kernel/git/ssantosh/linux
Santosh Shilimkar says:
====================
rds: add tos support
RDS applications make use of tos to classify database traffic.
This feature has been used in shipping products from 2.6.32 based
kernels. Its tied with RDS v4.1 protocol version and the compatibility
gets negotiated as part of connections setup.
Patchset keeps full backward compatibility using existing connection
negotiation scheme. Currently the feature is exploited by RDMA
transport and for TCP transport the user tos values are mapped to
same default class (0).
For RDMA transports, RDMA CM service type API is used to
set up different SL(service lanes) and the IB fabric is configured
for tos mapping using Subnet Manager(SL to VL mappings).
Similarly for ROCE fabric, user priority is mapped with different
DSCP code points which are associated with different switch queues
in the fabric.
The original code was developed by Bang Nguyen in downstream kernel back in
2.6.32 kernel days and it has evolved significantly over period of time.
Thanks to Yanjun for doing testing with various combinations of host like
v3.1<->v4.1, v4.1.<->v3.1, v4.1 upstream to shipping v4.1 etc etc
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 7 Feb 2019 00:56:20 +0000 (16:56 -0800)]
Merge git://git./linux/kernel/git/bpf/bpf-next
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-02-07
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add a riscv64 JIT for BPF, from Björn.
2) Implement BTF deduplication algorithm for libbpf which takes BTF type
information containing duplicate per-compilation unit information and
reduces it to an equivalent set of BTF types with no duplication and
without loss of information, from Andrii.
3) Offloaded and native BPF XDP programs can coexist today, enable also
offloaded and generic ones as well, from Jakub.
4) Expose various BTF related helper functions in libbpf as API which
are in particular helpful for JITed programs, from Yonghong.
5) Fix the recently added JMP32 code emission in s390x JIT, from Heiko.
6) Fix BPF kselftests' tcp_{server,client}.py to be able to run inside
a network namespace, also add a fix for libbpf to get libbpf_print()
working, from Stanislav.
7) Fixes for bpftool documentation, from Prashant.
8) Type cleanup in BPF kselftests' test_maps.c to silence a gcc8 warning,
from Breno.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 6 Feb 2019 22:24:05 +0000 (14:24 -0800)]
Merge branch 'mlxsw-blackhole-routes'
Ido Schimmel says:
====================
mlxsw: Offload blackhole routes
Blackhole routes are routes that cause matching packets to be silently
dropped. This is in contrast to unreachable routes that generate an ICMP
host unreachable packet in response.
The driver currently programs both route types with a trap action and
lets the kernel drop matching packets. This is sub-optimal as packets
routed using a blackhole route can be directly dropped by the ASIC.
Patch #1 alters mlxsw to program blackhole routes with a discard action.
Patch #2 adds a matching test.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 6 Feb 2019 19:42:03 +0000 (19:42 +0000)]
selftests: mlxsw: Add a test for blackhole routes
Use a simple topology consisting of two hosts directly connected to a
router. Make sure IPv4/IPv6 ping works and then add blackhole routes.
Test that ping fails and that the routes are marked as offloaded. Use a
simple tc filter to test that packets were dropped by the ASIC and not
trapped to the CPU.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 6 Feb 2019 19:42:01 +0000 (19:42 +0000)]
mlxsw: spectrum_router: Offload blackhole routes
Create a new FIB entry type for blackhole routes and set it in case the
type of the notified route is 'RTN_BLACKHOLE'.
Program such routes with a discard action and mark them as offloaded
since the device is dropping the packets instead of the kernel.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 6 Feb 2019 22:17:16 +0000 (14:17 -0800)]
Merge branch 'net-Introduce-ndo_get_port_parent_id'
Florian Fainelli says:
====================
net: Introduce ndo_get_port_parent_id()
Based on discussion with Ido and feedback from Jakub there are clearly
two classes of users that implement SWITCHDEV_ATTR_ID_PORT_PARENT_ID:
- PF/VF drivers which typically only implement return the port's parent
ID, yet have to implement switchdev_port_attr_get() just for that
- Ethernet switch drivers: mlxsw, ocelot, DSA, etc. which implement more
attributes which we want to be able to eventually veto in the context
of the caller, thus making them candidates for using a blocking notifier
chain
Changes in v4:
- remove superfluous net/switchdev.h inclusions in a few files
- added Jiri's Acked-by where given
- removed err = -EOPNOTSUPP initializations
- changed according to Jiri's suggestion in net/ipv4/ipmr.c
Changes in v3:
- keep ethsw's switchdev_ops assignment
- remove inclusion of net/switchdev.h in netdevsim which is no longer
necesary
Changes in v2:
- resolved build failures spotted by kbuild test robot
- added helpers functions into the core network device layer:
dev_get_port_parent_id() and netdev_port_same_parent_id();
- added support for recursion to lower devices
Changes from RFC:
- introduce a ndo_get_port_parent_id() and convert all relevant drivers
to use it
- get rid of SWITCHDEV_ATTR_ID_PORT_PARENT_ID
A subsequent set of patches will convert switchdev_port_attr_set() to
use a blocking notifier call, and still get rid of
switchdev_port_attr_get() altogether.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 6 Feb 2019 17:45:46 +0000 (09:45 -0800)]
net: Get rid of SWITCHDEV_ATTR_ID_PORT_PARENT_ID
Now that we have a dedicated NDO for getting a port's parent ID, get rid
of SWITCHDEV_ATTR_ID_PORT_PARENT_ID and convert all callers to use the
NDO exclusively. This is a preliminary change to getting rid of
switchdev_ops eventually.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 6 Feb 2019 17:45:45 +0000 (09:45 -0800)]
net: dsa: Implement ndo_get_port_parent_id()
DSA implements SWITCHDEV_ATTR_ID_PORT_PARENT_ID and we want to get rid
of switchdev_ops eventually, ease that migration by implementing a
ndo_get_port_parent_id() function which returns what
switchdev_port_attr_get() would do.
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 6 Feb 2019 17:45:44 +0000 (09:45 -0800)]
staging: fsl-dpaa2: ethsw: Implement ndo_get_port_parent_id()
ethsw implements SWITCHDEV_ATTR_ID_PORT_PARENT_ID and we want to get rid
of switchdev_ops eventually, ease that migration by implementing a
ndo_get_port_parent_id() function which returns what
switchdev_port_attr_get() would do.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 6 Feb 2019 17:45:43 +0000 (09:45 -0800)]
netdevsim: Implement ndo_get_port_parent_id()
netdevsim only supports SWITCHDEV_ATTR_ID_PORT_PARENT_ID, which makes it a
great candidate to be converted to use the ndo_get_port_parent_id() NDO
instead of implementing switchdev_port_attr_get().
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 6 Feb 2019 17:45:42 +0000 (09:45 -0800)]
rocker: Implement ndo_get_port_parent_id()
mlxsw implements SWITCHDEV_ATTR_ID_PORT_PARENT_ID and we want to get rid
of switchdev_ops eventually, ease that migration by implementing a
ndo_get_port_parent_id() function which returns what
switchdev_port_attr_get() would do.
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 6 Feb 2019 17:45:41 +0000 (09:45 -0800)]
nfp: Implement ndo_get_port_parent_id()
NFP only supports SWITCHDEV_ATTR_ID_PORT_PARENT_ID, which makes it a
great candidate to be converted to use the ndo_get_port_parent_id() NDO
instead of implementing switchdev_port_attr_get().
Since NFP uses switchdev_port_same_parent_id() convert it to use
netdev_port_same_parent_id().
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 6 Feb 2019 17:45:40 +0000 (09:45 -0800)]
mscc: ocelot: Implement ndo_get_port_parent_id()
Ocelot only supports SWITCHDEV_ATTR_ID_PORT_PARENT_ID as a valid
switchdev attribute getter, convert it to use ndo_get_port_parent_id()
and get rid of the switchdev_ops::switchdev_port_attr_get altogether.
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 6 Feb 2019 17:45:39 +0000 (09:45 -0800)]
mlxsw: Implement ndo_get_port_parent_id()
mlxsw implements SWITCHDEV_ATTR_ID_PORT_PARENT_ID and we want to get rid
of switchdev_ops eventually, ease that migration by implementing a
ndo_get_port_parent_id() function which returns what
switchdev_port_attr_get() would do.
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 6 Feb 2019 17:45:38 +0000 (09:45 -0800)]
net/mlx5e: Implement ndo_get_port_parent_id()
mlx5e only supports SWITCHDEV_ATTR_ID_PORT_PARENT_ID, which makes it a
great candidate to be converted to use the ndo_get_port_parent_id() NDO
instead of implementing switchdev_port_attr_get().
Since mlx5e makes use of switchdev_port_parent_id() convert it to use
netdev_port_same_parent_id().
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 6 Feb 2019 17:45:37 +0000 (09:45 -0800)]
liquidio: Implement ndo_get_port_parent_id()
Liquidio only supports SWITCHDEV_ATTR_ID_PORT_PARENT_ID, which makes it
a great candidate to be converted to use the ndo_get_port_parent_id()
NDO instead of implementing switchdev_port_attr_get().
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 6 Feb 2019 17:45:36 +0000 (09:45 -0800)]
bnxt: Implement ndo_get_port_parent_id()
BNXT only supports SWITCHDEV_ATTR_ID_PORT_PARENT_ID, which makes it a
great candidate to be converted to use the ndo_get_port_parent_id() NDO
instead of implementing switchdev_port_attr_get(). The conversion is
straight forward here since the PF and VF code use the same getter.
Since bnxt makes uses of switchdev_port_same_parent_id() convert it to
use netdev_port_same_parent_id().
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 6 Feb 2019 17:45:35 +0000 (09:45 -0800)]
net: Introduce ndo_get_port_parent_id()
In preparation for getting rid of switchdev_ops, create a dedicated NDO
operation for getting the port's parent identifier. There are
essentially two classes of drivers that need to implement getting the
port's parent ID which are VF/PF drivers with a built-in switch, and
pure switchdev drivers such as mlxsw, ocelot, dsa etc.
We introduce a helper function: dev_get_port_parent_id() which supports
recursion into the lower devices to obtain the first port's parent ID.
Convert the bridge, core and ipv4 multicast routing code to check for
such ndo_get_port_parent_id() and call the helper function when valid
before falling back to switchdev_port_attr_get(). This will allow us to
convert all relevant drivers in one go instead of having to implement
both switchdev_port_attr_get() and ndo_get_port_parent_id() operations,
then get rid of switchdev_port_attr_get().
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vishal Kulkarni [Wed, 6 Feb 2019 13:01:36 +0000 (18:31 +0530)]
cxgb4: Update 1.22.9.0 as the latest firmware supported.
Change t4fw_version.h to update latest firmware version
number to 1.22.9.0.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vishal Kulkarni [Wed, 6 Feb 2019 12:57:13 +0000 (18:27 +0530)]
cxgb4: Add new T6 PCI device ids 0x608b
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thierry Reding [Wed, 6 Feb 2019 12:30:18 +0000 (13:30 +0100)]
r8169: Avoid pointer aliasing
Read MAC address 32-bit at a time and manually extract the individual
bytes. This avoids pointer aliasing and gives the compiler a better
chance of optimizing the operation.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thierry Reding [Wed, 6 Feb 2019 12:30:17 +0000 (13:30 +0100)]
r8169: Load MAC address from device tree if present
If the system was booted using a device tree and if the device tree
contains a MAC address, use it instead of reading one from the EEPROM.
This is useful in situations where the EEPROM isn't properly programmed
or where the firmware wants to override the existing MAC address.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 6 Feb 2019 19:05:57 +0000 (11:05 -0800)]
Merge branch 'mlxsw-core-Trace-EMAD-errors'
Ido Schimmel says:
====================
mlxsw: core: Trace EMAD errors
Nir says:
This patchset adds a trace for EMAD errors to the existing EMAD payload
traces. This tracepoint is useful to track user or firmware errors during
tests execution.
Patch #1 defines the devlink tracepoint.
Patch #2 uses it for reporting mlxsw EMAD errors.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Nir Dotan [Mon, 4 Feb 2019 18:47:46 +0000 (18:47 +0000)]
mlxsw: core: Trace EMAD errors
Trace EMAD errors returned from HW.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nir Dotan [Mon, 4 Feb 2019 18:47:45 +0000 (18:47 +0000)]
devlink: add hardware errors tracing facility
Define a tracepoint and allow user to trace messages in case of an hardware
error code for hardware associated with devlink instance.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 6 Feb 2019 18:49:55 +0000 (10:49 -0800)]
Merge branch 'dpaa2-eth-Driver-updates'
Ioana Ciocoi Radulescu says:
====================
dpaa2-eth: Driver updates
First patch moves the driver to a page-per-frame memory model.
The others are minor tweaks and optimizations.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Ciocoi Radulescu [Mon, 4 Feb 2019 17:00:37 +0000 (17:00 +0000)]
dpaa2-eth: Update buffer pool refill threshold
Add more buffers to the Rx buffer pool as soon as 7 of them
get consumed, instead of waiting for their number to drop
below a fixed threshold.
7 is the number of buffers that can be released in the pool
via a single DPIO command.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Ciocoi Radulescu [Mon, 4 Feb 2019 17:00:36 +0000 (17:00 +0000)]
dpaa2-eth: Use FQ-based DPIO enqueue API
Starting with MC10.14.0, dpaa2_io_service_enqueue_fq() API is
functional. Since there are a number of cases where it offers
better performance compared to the currently used enqueue
function, switch to it for firmware versions that support it.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Ciocoi Radulescu [Mon, 4 Feb 2019 17:00:35 +0000 (17:00 +0000)]
dpaa2-eth: Use napi_consume_skb()
While in NAPI context, free skbs by calling napi_consume_skb()
instead of dev_kfree_skb(), to take advantage of the bulk freeing
mechanism.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Ciocoi Radulescu [Mon, 4 Feb 2019 17:00:35 +0000 (17:00 +0000)]
dpaa2-eth: Use a single page per Rx buffer
Instead of allocating page fragments via the network stack,
use the page allocator directly. For now, we consume one page
for each Rx buffer.
With the new memory model we are free to consider adding more
XDP support.
Performance decreases slightly in some IP forwarding cases.
No visible effect on termination traffic. The driver memory
footprint increases as a result of this change, but it is
still small enough to not really matter.
Another side effect is that now Rx buffer alignment requirements
are naturally satisfied without any additional actions needed.
Remove alignment related code, except in the buffer layout
information conveyed to MC, as hardware still needs to know the
alignment value we guarantee.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 6 Feb 2019 18:38:26 +0000 (10:38 -0800)]
Merge branch 'add-flow_rule-infrastructure'
Pablo Neira Ayuso says:
====================
add flow_rule infrastructure
This patchset, as is, allows us to reuse the driver codebase to
configure ACL hardware offloads for the ethtool_rxnfc and the TC flower
interfaces. A few clients for this infrastructure are presented, such as
the bcm_sf2 and the qede drivers, for reference. Moreover all of the
existing drivers in the tree are converted to use this infrastructure.
This patchset is re-using the existing flow dissector infrastructure
that was introduced by Jiri Pirko et al. so the amount of abstractions
that this patchset adds are minimal. Well, just a few wrapper structures
for the selector side of the rules. And, in order to express actions,
this patchset exposes an action API that is based on the existing TC
action infrastructure and what existing drivers already support on that
front.
v7: This patchset is a rebase on top of the net-next tree, after
addressing questions and feedback from driver developers in the
last batch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Sat, 2 Feb 2019 11:50:54 +0000 (12:50 +0100)]
qede: use ethtool_rx_flow_rule() to remove duplicated parser code
The qede driver supports for ethtool_rx_flow_spec and flower, both
codebases look very similar.
This patch uses the ethtool_rx_flow_rule() infrastructure to remove the
duplicated ethtool_rx_flow_spec parser and consolidate ACL offload
support around the flow_rule infrastructure.
Furthermore, more code can be consolidated by merging
qede_add_cls_rule() and qede_add_tc_flower_fltr(), these two functions
also look very similar.
This driver currently provides simple ACL support, such as 5-tuple
matching, drop policy and queue to CPU.
Drivers that support more features can benefit from this infrastructure
to save even more redundant codebase.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Sat, 2 Feb 2019 11:50:53 +0000 (12:50 +0100)]
qede: place ethtool_rx_flow_spec after code after TC flower codebase
This is a preparation patch to reuse the existing TC flower codebase
from ethtool_rx_flow_spec.
This patch is merely moving the core ethtool_rx_flow_spec parser after
tc flower offload driver code so we can skip a few forward function
declarations in the follow up patch.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Sat, 2 Feb 2019 11:50:52 +0000 (12:50 +0100)]
dsa: bcm_sf2: use flow_rule infrastructure
Update this driver to use the flow_rule infrastructure, hence we can use
the same code to populate hardware IR from ethtool_rx_flow and the
cls_flower interfaces.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Sat, 2 Feb 2019 11:50:51 +0000 (12:50 +0100)]
ethtool: add ethtool_rx_flow_spec to flow_rule structure translator
This patch adds a function to translate the ethtool_rx_flow_spec
structure to the flow_rule representation.
This allows us to reuse code from the driver side given that both flower
and ethtool_rx_flow interfaces use the same representation.
This patch also includes support for the flow type flags FLOW_EXT,
FLOW_MAC_EXT and FLOW_RSS.
The ethtool_rx_flow_spec_input wrapper structure is used to convey the
rss_context field, that is away from the ethtool_rx_flow_spec structure,
and the ethtool_rx_flow_spec structure.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Sat, 2 Feb 2019 11:50:50 +0000 (12:50 +0100)]
flow_offload: add wake-up-on-lan and queue to flow_action
These actions need to be added to support the ethtool_rx_flow interface.
The queue action includes a field to specify the RSS context, that is
set via FLOW_RSS flow type flag and the rss_context field in struct
ethtool_rxnfc, plus the corresponding queue index. FLOW_RSS implies that
rss_context is non-zero, therefore, queue.ctx == 0 means that FLOW_RSS
was not set. Also add a field to store the vf index which is stored in
the ethtool_rxnfc ring_cookie field.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Sat, 2 Feb 2019 11:50:49 +0000 (12:50 +0100)]
cls_flower: don't expose TC actions to drivers anymore
Now that drivers have been converted to use the flow action
infrastructure, remove this field from the tc_cls_flower_offload
structure.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Sat, 2 Feb 2019 11:50:48 +0000 (12:50 +0100)]
drivers: net: use flow action infrastructure
This patch updates drivers to use the new flow action infrastructure.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Sat, 2 Feb 2019 11:50:47 +0000 (12:50 +0100)]
flow_offload: add statistics retrieval infrastructure and use it
This patch provides the flow_stats structure that acts as container for
tc_cls_flower_offload, then we can use to restore the statistics on the
existing TC actions. Hence, tcf_exts_stats_update() is not used from
drivers anymore.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Sat, 2 Feb 2019 11:50:46 +0000 (12:50 +0100)]
cls_api: add translator to flow_action representation
This patch implements a new function to translate from native TC action
to the new flow_action representation. Moreover, this patch also updates
cls_flower to use this new function.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Sat, 2 Feb 2019 11:50:45 +0000 (12:50 +0100)]
flow_offload: add flow action infrastructure
This new infrastructure defines the nic actions that you can perform
from existing network drivers. This infrastructure allows us to avoid a
direct dependency with the native software TC action representation.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Sat, 2 Feb 2019 11:50:44 +0000 (12:50 +0100)]
net/mlx5e: support for two independent packet edit actions
This patch adds pedit_headers_action structure to store the result of
parsing tc pedit actions. Then, it calls alloc_tc_pedit_action() to
populate the mlx5e hardware intermediate representation once all actions
have been parsed.
This patch comes in preparation for the new flow_action infrastructure,
where each packet mangling comes in an separated action, ie. not packed
as in tc pedit.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Sat, 2 Feb 2019 11:50:43 +0000 (12:50 +0100)]
flow_offload: add flow_rule and flow_match structures and use them
This patch wraps the dissector key and mask - that flower uses to
represent the matching side - around the flow_match structure.
To avoid a follow up patch that would edit the same LoCs in the drivers,
this patch also wraps this new flow match structure around the flow rule
object. This new structure will also contain the flow actions in follow
up patches.
This introduces two new interfaces:
bool flow_rule_match_key(rule, dissector_id)
that returns true if a given matching key is set on, and:
flow_rule_match_XYZ(rule, &match);
To fetch the matching side XYZ into the match container structure, to
retrieve the key and the mask with one single call.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 6 Feb 2019 17:52:43 +0000 (09:52 -0800)]
Merge branch 'net-phy-add-and-use-further-MMD-accessors'
Heiner Kallweit says:
====================
net: phy: add and use further MMD accessors
Add MMD accessors for modifying MMD registers and clearing / setting
bits in MMD registers. Use these accessors in PHY drivers and phylib.
v2:
- fix SoB in patch 2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Wed, 6 Feb 2019 06:38:43 +0000 (07:38 +0100)]
net: phy: make use of new MMD accessors
Make use of the new MMD accessors.
v2:
- fix SoB
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikita Yushchenko [Wed, 6 Feb 2019 06:36:40 +0000 (07:36 +0100)]
net: phy: provide full set of accessor functions to MMD registers
This adds full set of locked and unlocked accessor functions to read and
write PHY MMD registers and/or bitfields.
Set of functions exactly matches what is already available for PHY
legacy registers.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 6 Feb 2019 17:36:36 +0000 (09:36 -0800)]
Merge tag 'wireless-drivers-next-for-davem-2019-02-06' of git://git./linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.1
First set of patches for 5.1. Lots of new features in various drivers
but nothing really special standing out.
Major changes:
brcmfmac
* DMI nvram filename quirk for PoV TAB-P1006W-232 tablet
rsi
* support for hardware scan offload
iwlwifi
* support for Target Wakeup Time (TWT) -- a feature that allows the AP
to specify when individual stations can access the medium
* support for mac80211 AMSDU handling
* some new PCI IDs
* relicense the pcie submodule to dual GPL/BSD
* reworked the TOF/CSI (channel estimation matrix) implementation
* Some product name updates in the human-readable strings
mt76
* energy detect regulatory compliance fixes
* preparation for MT7603 support
* channel switch announcement support
mwifiex
* support for sd8977 chipset
qtnfmac
* support for 4addr mode
* convert to SPDX license identifiers
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Breno Leitao [Tue, 5 Feb 2019 17:12:34 +0000 (15:12 -0200)]
bpf: test_maps: fix possible out of bound access warning
When compiling test_maps selftest with GCC-8, it warns that an array
might be indexed with a negative value, which could cause a negative
out of bound access, depending on parameters of the function. This
is the GCC-8 warning:
gcc -Wall -O2 -I../../../include/uapi -I../../../lib -I../../../lib/bpf -I../../../../include/generated -DHAVE_GENHDR -I../../../include test_maps.c /home/breno/Devel/linux/tools/testing/selftests/bpf/libbpf.a -lcap -lelf -lrt -lpthread -o /home/breno/Devel/linux/tools/testing/selftests/bpf/test_maps
In file included from test_maps.c:16:
test_maps.c: In function ‘run_all_tests’:
test_maps.c:1079:10: warning: array subscript -1 is below array bounds of ‘pid_t[<Ube20> + 1]’ [-Warray-bounds]
assert(waitpid(pid[i], &status, 0) == pid[i]);
^~~~~~~~~~~~~~~~~~~~~~~~~~~
test_maps.c:1059:6: warning: array subscript -1 is below array bounds of ‘pid_t[<Ube20> + 1]’ [-Warray-bounds]
pid[i] = fork();
~~~^~~
This patch simply guarantees that the task(s) variables are unsigned,
thus, they could never be a negative number (which they are not in
current code anyway), hence avoiding an out of bound access warning.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Prashant Bhole [Wed, 6 Feb 2019 01:47:23 +0000 (10:47 +0900)]
tools: bpftool: doc, fix incorrect text
Documentation about cgroup, feature, prog uses wrong header
'MAP COMMANDS' while listing commands. This patch corrects the header
in respective doc files.
Signed-off-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Acked-by: Yonghong Song <yhs@fb.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Daniel Borkmann [Wed, 6 Feb 2019 14:35:43 +0000 (15:35 +0100)]
Merge branch 'bpf-xdp-hw-plus-generic'
Jakub Kicinski says:
====================
Offloaded and native/driver XDP programs can already coexist.
Allow offload and generic hook to coexist as well, there seem
to be no reason why not to do so.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jakub Kicinski [Wed, 6 Feb 2019 04:03:24 +0000 (20:03 -0800)]
selftests/bpf: test reading the offloaded program
Test adding the offloaded program after the other program
is already installed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jakub Kicinski [Wed, 6 Feb 2019 04:03:23 +0000 (20:03 -0800)]
selftests/bpf: add test for mixing generic and offload XDP
Add simple sanity check for enabling generic and offload
XDP, simply reuse the native and offload checks.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jakub Kicinski [Wed, 6 Feb 2019 04:03:22 +0000 (20:03 -0800)]
selftests/bpf: print traceback when test fails
Figuring out which exact check in test_offload.py takes more
time than it should. Print the traceback (to the screen and
the logs).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jakub Kicinski [Wed, 6 Feb 2019 04:03:21 +0000 (20:03 -0800)]
net: xdp: allow generic and driver XDP on one interface
Since commit
a25717d2b604 ("xdp: support simultaneous driver and
hw XDP attachment") users can load an XDP program for offload and
in native driver mode simultaneously. Allow a similar mix of
offload and SKB mode/generic XDP.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jakub Kicinski [Wed, 6 Feb 2019 04:03:20 +0000 (20:03 -0800)]
selftests/bpf: fix the expected messages
Recent changes added extack to program replacement path,
expect extack instead of generic messages.
Fixes:
01dde20ce04b ("xdp: Provide extack messages when prog attachment failed")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Yonghong Song [Wed, 6 Feb 2019 05:38:30 +0000 (21:38 -0800)]
tools/bpf: silence a libbpf unnecessary warning
Commit
96408c43447a ("tools/bpf: implement libbpf
btf__get_map_kv_tids() API function") refactored
function bpf_map_find_btf_info() and moved bulk of
implementation into btf.c as btf__get_map_kv_tids().
This change introduced a bug such that test_btf will
print out the following warning although the test passed:
BTF libbpf test[2] (test_btf_nokv.o): libbpf: map:btf_map
container_name:____btf_map_btf_map cannot be found
in BTF. Missing BPF_ANNOTATE_KV_PAIR?
Previously, the error message is guarded with pr_debug().
Commit
96408c43447a changed it to pr_warning() and
hence caused the warning.
Restoring to pr_debug() for the message fixed the issue.
Fixes:
96408c43447a ("tools/bpf: implement libbpf btf__get_map_kv_tids() API function")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
David S. Miller [Wed, 6 Feb 2019 04:15:30 +0000 (20:15 -0800)]
Merge branch '1GbE' of git://git./linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2019-02-05
This series contains updates to igc, e1000e, ixgbe, fm10k and driver
documentation.
Kai-Heng Feng fixes an e1000e issue where the Wake-On-LAN settings where
being set incorrectly during a system suspend.
Sasha addresses community feedback on the igc driver and provides a
number of code cleanups to remove either unreachable or unused code. In
addition, added basic ethtool support for the igc driver.
Mike Rapoport fixes the formatting of the kernel driver documentation so
that the title is properly formatted and does not get lumped with the
document sections in the HTML kernel documents generated.
Jiri Kosina updates a hard coded RAR entries value with the existing
define IXGBE_82599_RAR_ENTRIES.
Jake fixes up whitespace in the fm10k driver.
Konstantin Khlebnikov fixes an issue where in some cases, the e1000e
driver will continually reset during a system boot because the watchdog
task sees items in the transmit buffer but the carrier is off (trying to
establish link) causing the device reset to flush the buffer. To
resolve, just move this check/flush into the watchdog section for when
the carrier is off.
Todd bumps the igb driver version to reflect the recent driver changes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Yonghong Song [Tue, 5 Feb 2019 19:48:22 +0000 (11:48 -0800)]
tools/bpf: add const qualifier to btf__get_map_kv_tids() map_name parameter
Commit
96408c43447a ("tools/bpf: implement libbpf btf__get_map_kv_tids() API function")
added the API function btf__get_map_kv_tids():
btf__get_map_kv_tids(const struct btf *btf, char *map_name, ...)
The parameter map_name has type "char *". This is okay inside libbpf library since
the map_name is from bpf_map->name which also has type "char *".
This will be problematic if the caller for map_name already has attribute "const",
e.g., from C++ string.c_str(). It will result in either a warning or an error.
/home/yhs/work/bcc/src/cc/btf.cc:166:51:
error: invalid conversion from ‘const char*’ to ‘char*’ [-fpermissive]
return btf__get_map_kv_tids(btf_, map_name.c_str()
This patch added "const" attributes to map_name parameter.
Fixes:
96408c43447a ("tools/bpf: implement libbpf btf__get_map_kv_tids() API function")
Signed-off-by: Yonghong Song <yhs@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Yonghong Song [Tue, 5 Feb 2019 22:28:44 +0000 (14:28 -0800)]
tools/bpf: fix a selftest test_btf failure
Commit
9c651127445c ("selftests/btf: add initial BTF dedup tests")
added dedup tests in test_btf.c.
It broke the raw test:
BTF raw test[71] (func proto (Bad arg name_off)):
btf_raw_create:2905:FAIL Error getting string #65535, strs_cnt:1
The test itself encodes invalid func_proto parameter name
offset 0xffffFFFF as a negative test for the kernel.
The above commit changed the meaning of that offset and
resulted in a user space error.
#define NAME_NTH(N) (0xffff0000 | N)
#define IS_NAME_NTH(X) ((X & 0xffff0000) == 0xffff0000)
#define GET_NAME_NTH_IDX(X) (X & 0x0000ffff)
Currently, the kernel permits maximum name offset 0xffff.
Set the test name off as 0x0fffFFFF to trigger the kernel
verification failure.
Cc: Andrii Nakryiko <andriin@fb.com>
Fixes:
9c651127445c ("selftests/btf: add initial BTF dedup tests")
Signed-off-by: Yonghong Song <yhs@fb.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Sasha Neftin [Wed, 30 Jan 2019 17:13:14 +0000 (19:13 +0200)]
igc: Add ethtool support
This patch adds basic ethtool support to the device to allow
for configuration.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Todd Fujinaka [Wed, 23 Jan 2019 22:56:30 +0000 (14:56 -0800)]
igb: Bump version number
With recent changes, need to bump the driver version to reflect the
changes.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sasha Neftin [Tue, 15 Jan 2019 13:21:18 +0000 (15:21 +0200)]
igc: Remove the 'igc_get_phy_id_base' method
Remove the redundant 'igc_get_phy_id_base' method and use
the 'igc_get_phy_id' method directly instead.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sasha Neftin [Tue, 15 Jan 2019 13:21:09 +0000 (15:21 +0200)]
igc: Remove the 'igc_read_mac_addr_base' method
Remove the redundant 'igc_read_mac_addr_base' method and use
the 'igc_read_mac_addr' method directly instead.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Konstantin Khlebnikov [Mon, 14 Jan 2019 13:29:30 +0000 (16:29 +0300)]
e1000e: fix cyclic resets at link up with active tx
I'm seeing series of e1000e resets (sometimes endless) at system boot
if something generates tx traffic at this time. In my case this is
netconsole who sends message "e1000e 0000:02:00.0: Some CPU C-states
have been disabled in order to enable jumbo frames" from e1000e itself.
As result e1000_watchdog_task sees used tx buffer while carrier is off
and start this reset cycle again.
[ 17.794359] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[ 17.794714] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 22.936455] e1000e 0000:02:00.0 eth1: changing MTU from 1500 to 9000
[ 23.033336] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 26.102364] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[ 27.174495] 8021q: 802.1Q VLAN Support v1.8
[ 27.174513] 8021q: adding VLAN 0 to HW filter on device eth1
[ 30.671724] cgroup: cgroup: disabling cgroup2 socket matching due to net_prio or net_cls activation
[ 30.898564] netpoll: netconsole: local port 6666
[ 30.898566] netpoll: netconsole: local IPv6 address 2a02:6b8:0:80b:beae:c5ff:fe28:23f8
[ 30.898567] netpoll: netconsole: interface 'eth1'
[ 30.898568] netpoll: netconsole: remote port 6666
[ 30.898568] netpoll: netconsole: remote IPv6 address 2a02:6b8:b000:605c:e61d:2dff:fe03:3790
[ 30.898569] netpoll: netconsole: remote ethernet address b0:a8:6e:f4:ff:c0
[ 30.917747] console [netcon0] enabled
[ 30.917749] netconsole: network logging started
[ 31.453353] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.185730] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.321840] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.465822] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.597423] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.745417] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.877356] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 35.005441] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 35.157376] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 35.289362] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 35.417441] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 37.790342] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
This patch flushes tx buffers only once when carrier is off
rather than at each watchdog iteration.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sasha Neftin [Sun, 13 Jan 2019 09:22:31 +0000 (11:22 +0200)]
igc: Remove unneeded code
Remove the 'igc_get_link_up_info_base method' from igc_base.c file.
Use the 'igc_get_speed_and_duplex_copper' method directly and reduce
the code redundancy.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sasha Neftin [Mon, 7 Jan 2019 14:40:17 +0000 (16:40 +0200)]
igc: Remove unused code
Remove unused igc_adv_data_desc definition from igc_base.h file.
Descriptors definition will be added per demand.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>