Mark Tomlinson [Wed, 1 Jul 2015 04:38:24 +0000 (16:38 +1200)]
JFFS2: Only list each directory entry once
If multiple versions of a file exist, only the most recent version
should be used. The scheme to write 0 for the inode in older versions
did not work, since this would have required writing to flash.
The only time this caused an issue was listing a directory, where older
versions of the file would still be seen. Since the directory entries
are sorted, just look at the next entry in the list, and if it's the same
move to that entry instead.
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Mark Tomlinson [Wed, 1 Jul 2015 04:38:23 +0000 (16:38 +1200)]
JFFS2: Speed up and fix comparison functions
Copying complete nodes from flash can be slow if the flash is slow
to read. By only reading the data needed, the sorting operation can
be made much faster.
The directory entry comparison function also had a two bugs. First, it
did not ensure the name was copied, so the name comparison may have
been faulty (although it would have worked with NOR flash). Second,
setting the ino to zero to ignore the entry did not work, since this
was either writing to a temporary buffer, or (for NOR flash) directly
to flash. Either way, the change was not remembered.
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Mark Tomlinson [Wed, 1 Jul 2015 04:38:22 +0000 (16:38 +1200)]
JFFS2: Return early when file read not necessary
If a destination is not provided, jffs2_1pass_read_inode() only
returns the length of the file. In this case, avoid reading all
the data nodes, and return as soon as the length of the file is
known.
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Jiandong Zheng [Wed, 15 Jul 2015 23:28:14 +0000 (16:28 -0700)]
arm: bcmcygnus: Enable Ethernet support
Enable BCM SF2 ethernet and PHY for BCM Cygnus SoC
Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Heiko Schocher [Mon, 29 Jun 2015 07:10:48 +0000 (09:10 +0200)]
arm, at91: support for sam9260 based smartweb board
add support for the at91sam9260 based board smartweb from
siemens. SPL is used without serial support, as this
SoC has only 4k sram for running SPL. Here a U-Boot
bootlog:
RomBOOT
>
U-Boot 2015.07-rc2-00109-g4ae828c (Jun 15 2015 - 09:31:16 +0200)
CPU: AT91SAM9260
Crystal frequency: 18.432 MHz
CPU clock : 198.656 MHz
Master clock : 99.328 MHz
Watchdog enabled
DRAM: 64 MiB
WARNING: Caches not enabled
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Net: macb0
Hit any key to stop autoboot: 0
U-Boot>
Signed-off-by: Heiko Schocher <hs@denx.de>
Heiko Schocher [Mon, 29 Jun 2015 07:10:47 +0000 (09:10 +0200)]
nand, atmel: remove udelay in spl_nand_erase_one()
remove unneeded udelay() in this function, as we use
the dev_ready pin.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Heiko Schocher [Mon, 29 Jun 2015 07:10:46 +0000 (09:10 +0200)]
spl, common, serial: build SPL without serial support
This patch enables building SPL without
CONFIG_SPL_SERIAL_SUPPORT support.
Signed-off-by: Heiko Schocher <hs@denx.de>
[trini: Ensure we build arch/arm/imx-common on mx28]
Signed-off-by: Tom Rini <trini@konsulko.com>
Dennis Gilmore [Sun, 28 Jun 2015 19:05:12 +0000 (14:05 -0500)]
port vexpress to use distro boot commands
remove options defined in the distro defaults
add distro bot commands
set scriptaddr value
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
Dennis Gilmore [Sun, 28 Jun 2015 19:05:11 +0000 (14:05 -0500)]
Move setting CONFIG_BOOTP_VCI_STRING to before including the vexpress-common header
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
Dennis Gilmore [Sun, 28 Jun 2015 19:05:10 +0000 (14:05 -0500)]
PXE: if a board has set its own value for CONFIG_BOOTP_VCI_STRING do not set the default one. Use the board set value instead
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
Rob Herring [Sat, 20 Jun 2015 23:29:55 +0000 (00:29 +0100)]
ARM: highbank: remove DRAM bank setup
On the highbank platform the SoC's management controller firmware
will probe the DRAM modules and populates the initial device tree with
the correct values. Therefore the memory sizes in the DT are already
correct, so remove U-Boot's DRAM bank setup so the memory node is not
"fixed up" by u-boot.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andre Przywara <osp@andrep.de>
Simon Glass [Sun, 9 Aug 2015 15:10:57 +0000 (09:10 -0600)]
dm: pmic: max77686: Correct two typos in a comment
These were pointed out in review but I missed them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Peng Fan [Tue, 28 Jul 2015 14:47:08 +0000 (22:47 +0800)]
power: regulator: max77686 correct variable type
The return type of pmic_read and pmic_write is signed int, so
correct variable 'ret' from type unsigned int to int.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Peng Fan [Fri, 7 Aug 2015 08:43:46 +0000 (16:43 +0800)]
fsl: common: pfuze: no use original pfuze code if DM_PMIC
If enable DM PMIC and REGULATOR, we should not use original power
framework. So need to comment out the pfuze code for original power
framework, when CONFIG_DM_PMIC_PFUZE100 defined.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Peng Fan [Fri, 7 Aug 2015 08:43:45 +0000 (16:43 +0800)]
power: regulator: add pfuze100 support
1. Add new regulator driver pfuze100.
* Introduce struct pfuze100_regulator_desc for maintaining info
for one regulator.
2. Add new Kconfig entry DM_REGULATOR_PFUZE100 for pfuze100.
3. This driver intends to support PF100, PF200 and PF3000.
4. Add related macro definition in pfuze header file.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Peng Fan [Fri, 7 Aug 2015 08:43:44 +0000 (16:43 +0800)]
power: pmic: pfuze100 support driver model
1. Support driver model for pfuze100.
2. Introduce a new Kconfig entry DM_PMIC_PFUZE100 for pfuze100
3. This driver intends to support PF100, PF200 and PF3000, so add
the device id into the udevice_id array.
4. Rename PMIC_NUM_OF_REGS macro to PFUZE100_NUM_OF_REGS.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Peng Fan [Fri, 7 Aug 2015 08:43:43 +0000 (16:43 +0800)]
power: regulator: update comments for regulator-name
We do not need that "regulator-name" property must be provided in dts.
If "regulator-name" property is not provided in dts, node name
will chosen for settings '.name' field of uc_pdata.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Peng Fan [Fri, 7 Aug 2015 08:43:42 +0000 (16:43 +0800)]
power: regulator use node name when no regulator-name
If there is no property named 'regulator-name' for regulators,
choose node name instead, but not directly return failure value.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Peng Fan [Fri, 7 Aug 2015 08:43:41 +0000 (16:43 +0800)]
power: pfuze100 correct SWBST macro definition
According to datasheet, SWBST_MODE starts from bit 2 and it occupies 2 bits.
So SWBST_MODE_MASK should be 0xC, and SWBST_MODE_xx should be ([mode] << 2).
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Mon, 10 Aug 2015 14:06:07 +0000 (10:06 -0400)]
Merge git://git.denx.de/u-boot-dm
Hans de Goede [Sat, 8 Aug 2015 15:45:18 +0000 (17:45 +0200)]
dm: serial: Add a REQUIRE_SERIAL_CONSOLE option for boards with no serial port
Currently the serial code assumes that there is always at least one serial
port (and panics / crashes due to null pointer dereferences when there is
none).
This makes it impossible to use u-boot on boards where there is no (debug)
serial port, because e.g. all uart pins are muxed to another function.
This commit adds a CONFIG_REQUIRE_SERIAL_CONSOLE Kconfig option, which
defaults to y (preserving existing behavior), which can be set to n on
such boards to make them work.
This commit only implements this for CONFIG_DM_SERIAL=y configs, as allowing
running without a serial port for CONFIG_DM_SERIAL=n configs is non trivial,
and is not necessary at this moment.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tom Rini [Sun, 9 Aug 2015 00:20:17 +0000 (20:20 -0400)]
Merge branch 'master' of git.denx.de/u-boot-sunxi
Hans de Goede [Mon, 3 Aug 2015 17:20:26 +0000 (19:20 +0200)]
sunxi: display: Add composite video out support
Add composite video out support.
This only gets enabled on the Mele M3 for now, since that is were it
was tested. It will be enabled on more boards after testing.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sun, 2 Aug 2015 14:49:29 +0000 (16:49 +0200)]
sunxi: display: Add support for interlaced modes
Add support for interlaced modes, this is a preparation patch for adding
composite out support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Mon, 3 Aug 2015 17:45:37 +0000 (19:45 +0200)]
sunxi: display: Add a few extra register and constant defines
Add a few extra sunxi display registers and constant defines.
Also rename some existing defines (e.g. dropping _GCTRL) and make
some more generic (e.g. dropping the 2x scaling from
SUNXI_LCDC_TCON1_TIMING_V_TOTAL).
This is a preparation patch for adding composite video out support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sun, 2 Aug 2015 15:38:43 +0000 (17:38 +0200)]
sunxi: display: Correct clk_delay calculations for lcd displays
We should only subtract 2 from the vblank time when using tcon1.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Mon, 3 Aug 2015 21:01:38 +0000 (23:01 +0200)]
sunxi: display: Replace #ifdef-ery with helper functions
All the #ifdef-ery in selecting the default and fallback monitor type is
becoming unyielding and makes the code hard to read, replace it with a few
helper functions.
This will also be useful with the upcoming CHIP board which has display
adapter daughterboards which should be runtime detectable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Tue, 4 Aug 2015 21:49:17 +0000 (23:49 +0200)]
sunxi: Enable musb in host mode on the Jesurun Q5
The Jesurun Q5 has the musb hooked up to an usb-a receptacle, enable it
in host-only mode.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sat, 1 Aug 2015 12:44:29 +0000 (14:44 +0200)]
sunxi: Do not add a stdout-path alias to dts on boards without a serial port
Do not add a bogus (pointing to a non existing serial port) stdout-path
alias to dts on boards without a serial port.
Note that we still define CONS_INDEX as this is used by the SPL where we do
not use DM_SERIAL and thus CONFIG_REQUIRE_SERIAL_CONSOLE is not honored.
We are getting away with this because the sun5i die actually has
an uart0, which in the A13 package is not routed to the outside,
so we are simply sending SPL bootup messages to the tx pin at the
edge of the die, and they go no further from there...
And sofar we only have one A13 board which does not have a serial
port, all others do have a serial port. This kinda makes sense since
the A13 is a much lower pincount package compared to all the other
sunxi SoCs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sat, 1 Aug 2015 12:42:40 +0000 (14:42 +0200)]
sunxi: Add CONFIG_USB0_ID_DET setting to 2 more tablets
Now that we have code to check the id-pin and detect usb-host adapters
plugged into the otg port that way, enable it on the tablets which I own.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Wed, 8 Jul 2015 14:44:22 +0000 (16:44 +0200)]
sunxi: usb-phy: Never power off the usb ports
USB devices are not really designed to get the power bounced off and on
at them. Esp. USB powered harddisks do not like this.
Currently we power off the USB ports both on a "usb reset" and when
booting the kernel, causing the usb-power to bounce off and then back
on again.
This patch removes the powering off calls, fixing the undesirable power
bouncing.
Note this requires some special handling for the OTG port:
1) We must skip the external vbus check if we've already enabled our own
vbus to avoid false positives
2) If on an usb reset we no longer detect that the id-pin is grounded, turn
off vbus as that means an external vbus may be present now
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Piotr Zierhoffer [Thu, 23 Jul 2015 12:33:03 +0000 (14:33 +0200)]
sunxi: nand: Add board configuration options
When SPL_NAND_SUNXI option is selected in config, set some configuration
options for sunxi NAND.
This commit also introduces the configurable options in Kconfig.
Signed-off-by: Peter Gielda <pgielda@antmicro.com>
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Signed-off-by: Karol Gugala <kgugala@antmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Piotr Zierhoffer [Thu, 23 Jul 2015 12:33:02 +0000 (14:33 +0200)]
sunxi: nand: Add basic sunxi NAND driver for SPL with DMA support
This driver adds NAND support to SPL.
It was tested on Allwinner A20.
Signed-off-by: Peter Gielda <pgielda@antmicro.com>
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Signed-off-by: Karol Gugala <kgugala@antmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Karol Gugala [Thu, 23 Jul 2015 12:33:01 +0000 (14:33 +0200)]
sunxi: nand: Add pinmux and clock settings for NAND support
To enable NAND flash in sunxi SPL,
pins 0-6, 8-22 and 24 on port C are configured.
Signed-off-by: Karol Gugala <kgugala@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Aleksei Mamlin [Thu, 30 Jul 2015 17:33:56 +0000 (20:33 +0300)]
sunxi: Enable USB DRC on Wexler TAB7200
Enable the otg/drc usb controller on the Wexler TAB7200 tablet.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Dinh Nguyen [Sat, 1 Aug 2015 01:42:10 +0000 (03:42 +0200)]
arm: socfpga: misc: Add support for printing FPGA type
Add code which uses the new functions for obtaining FPGA ID from
the scan manager. This new code prints the FPGA model attached to
the SoCFPGA during boot and sets environment variable "fpgatype",
which can be used to determine the FPGA model in U-Boot scripts.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Dinh Nguyen [Fri, 31 Jul 2015 16:06:50 +0000 (11:06 -0500)]
arm: socfpga: scan: Add code to get FPGA ID
Add code to get the FPGA type for Altera's SoCFPGA family of FPGA. The code
uses the scan manager to send jtag pulses that will return the FPGA ID.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Sat, 1 Aug 2015 12:28:48 +0000 (14:28 +0200)]
arm: socfpga: scan: Factor out IO chain programming
Factor out the code which sends JTAG instruction followed by data
into separate function to tidy the code up a little.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Sat, 1 Aug 2015 01:18:50 +0000 (03:18 +0200)]
arm: socfpga: scan: Clean up horrible macros
Clean up the horrible macros present in the scan_manager.h . Firstly,
the function scan_mgr_io_scan_chain_prg() is static, yet all the macros
are used only within it, thus there is no point in having them in the
header file. Moreover, the macros are just making the code much less
readable, so remove them instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Sat, 1 Aug 2015 01:01:25 +0000 (03:01 +0200)]
arm: socfpga: scan: Introduce generic JTAG accessor
Introduce generic function for accessing the JTAG scan chains in the
SCC manager. Make use of this function throughout the SCC manager to
replace the ad-hoc writes to registers and make the code less cryptic.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Sat, 1 Aug 2015 00:48:03 +0000 (02:48 +0200)]
arm: socfpga: scan: Clean up scan_chain_engine_is_idle()
Rework this function so it's clear that it is only polling for certain
bits to be cleared. Add kerneldoc. Fix it's return value to be either
0 on success and -ETIMEDOUT on error and propagate this through the
scan manager code.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Dinh Nguyen [Wed, 5 Aug 2015 03:12:32 +0000 (22:12 -0500)]
ddr: altera: sequencer: add RW_MGR_MEM_NUMBER_OF_RANKS
Fix build error for socfpga_cyclone5_defconfig:
board/altera/socfpga/wrap_sdram_config.c:245:26: error: ‘RW_MGR_MEM_NUMBER_OF_RANKS’ undeclared here (not in a function)
make[2]: *** [spl/board/altera/socfpga/wrap_sdram_config.o] Error 1
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Sun, 2 Aug 2015 17:47:01 +0000 (19:47 +0200)]
ddr: altera: sequencer: Clean checkpatch issues
Fix most of the dangling checkpatch issues, no functional change.
There are still 7 warnings, 1 checks , but those are left in place
for the sake of readability of the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Sun, 2 Aug 2015 17:42:26 +0000 (19:42 +0200)]
ddr: altera: sequencer: Clean data types
Replace uintNN_t with uNN. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Sun, 2 Aug 2015 17:26:55 +0000 (19:26 +0200)]
ddr: altera: sequencer: Pluck out misc macros from code
Actually convert the sequencer code to use socfpga_sdram_misc_config
instead of the various macros. This is just an sed exercise here, no
manual coding needed.
This patch actually removes the need to include any board-specific
files in sequencer.c , so sequencer.c namespace is now no longer
poluted by QTS-generated macros.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Sun, 2 Aug 2015 17:24:12 +0000 (19:24 +0200)]
ddr: altera: sequencer: Zap SEQ_T(INIT|RESET)_CNTR._VAL
This is another macro used to obfuscate the real code. The
T(INIT|RESET)_CNTR._VAL is always defined, so this indirection
is unnecessary. Get rid of this.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Sun, 2 Aug 2015 17:21:56 +0000 (19:21 +0200)]
ddr: altera: sequencer: Zap VFIFO_SIZE
Just use READ_VALID_FIFO_SIZE directly, no need for this macro obfuscation.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Sun, 2 Aug 2015 17:18:47 +0000 (19:18 +0200)]
ddr: altera: sequencer: Wrap misc remaining macros
Introduce structure socfpga_sdram_misc_config to wrap the remaining
misc configuration values in board file. Again, introduce a function,
socfpga_get_sdram_misc_config(), which returns this the structure. This
is almost the final step toward wrapping the nasty QTS generated macros
in board files and reducing the pollution of the namespace.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Sun, 2 Aug 2015 17:10:58 +0000 (19:10 +0200)]
ddr: altera: sequencer: Pluck out IO_* macros from code
Actually convert the sequencer code to use socfpga_sdram_io_config
instead of the IO_* macros. This is just an sed excercise here, no
manual coding needed.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Sun, 2 Aug 2015 17:00:23 +0000 (19:00 +0200)]
ddr: altera: sequencer: Wrap IO_* macros
Introduce structure socfpga_sdram_io_config to wrap the IO configuration
values in board file. Introduce socfpga_get_sdram_io_config() function,
which returns this the structure. This is another step toward wrapping
the nasty QTS generated macros in board files and reducing the pollution
of the namespace.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Sun, 2 Aug 2015 16:44:06 +0000 (18:44 +0200)]
ddr: altera: sequencer: Pluck out RW_MGR_* macros from code
Actually convert the sequencer code to use socfpga_sdram_rw_mgr_config
instead of the RW_MGR_* macros. This is just an sed exercise here, no
manual coding needed.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Sun, 2 Aug 2015 16:12:08 +0000 (18:12 +0200)]
ddr: altera: sequencer: Wrap RW_MGR_* macros
Introduce structure socfpga_sdram_rw_mgr_config to wrap the RW manager
configuration values in board file. Introduce a complementary function,
socfpga_get_sdram_rwmgr_config(), which returns this the structure.
This is another step toward wrapping the nasty QTS generated macros
in board files and reducing the pollution of the namespace.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Sun, 2 Aug 2015 15:15:19 +0000 (17:15 +0200)]
ddr: altera: sequencer: Wrap ac_rom_init and inst_rom_init
Introduce two wrapper functions, socfpga_get_seq_ac_init() and
socfpga_get_seq_inst_init() to avoid direct inclusion of the
sequencer_auto_ac_init.h and sequencer_auto_inst_init.h QTS
generated files. This reduces namespace pollution again.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Sun, 2 Aug 2015 16:40:27 +0000 (18:40 +0200)]
ddr: altera: sequencer: Zap bogus redefinition of RW_MGR_MEM_NUMBER_OF_RANKS
This is defined in the QTS-generated headers, so it must not be
re-defined in sequencer.h .
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Sun, 2 Aug 2015 16:27:21 +0000 (18:27 +0200)]
ddr: altera: sequencer: Zap unused params and macros
These parameters are not used in the code, zap them and the
macros which are used by them as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Sun, 2 Aug 2015 15:02:11 +0000 (17:02 +0200)]
ddr: altera: sequencer: Clean up mach/sdram.h
Zap non-existent functions and place function prototypes at the
beginning of the header file.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Sun, 2 Aug 2015 14:55:45 +0000 (16:55 +0200)]
ddr: altera: sequencer: Move qts-generated files to board dir
Move the files generated by QTS into the board directory, they should not
be part of the driver files at all.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Sat, 1 Aug 2015 21:12:11 +0000 (23:12 +0200)]
ddr: altera: sdram: Make sdram_start and sdram_end into u32
Originally, both sdram_start and sdram_end were 64b values. The
sdram_start had no reason for being so, since our address space
is only 32b, so switching sdram_start to u32 is simple.
The sdram_end is a bit more complex, since it can actually be
set to (1 << 32) if someone really wanted to use an SoCFPGA with
4 GiB of DRAM and fixed the code around a little. But, the code
handling the protection rules internally decrements the sdram_end
variable anyway. Thus, instead of calling the code and passing in
the address of the SDRAM end, pass in the address already decremented
by one. This lets the sdram_end be 32b as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sat, 1 Aug 2015 21:21:23 +0000 (23:21 +0200)]
ddr: altera: sdram: Minor cleanup in sdram_get_rule()
Fix the data types and zap unnecessary type change.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sat, 1 Aug 2015 20:40:48 +0000 (22:40 +0200)]
ddr: altera: sdram: Minor cleanup in sdram_set_rule()
Zap an obscure unneeded cast and clean other minor nits in this function.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sat, 1 Aug 2015 20:28:30 +0000 (22:28 +0200)]
ddr: altera: sdram: Add missing kerneldoc
Add kerneldoc to functions which are missing it, but are already
cleaned up.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sat, 1 Aug 2015 20:26:11 +0000 (22:26 +0200)]
ddr: altera: sdram: Clean up sdram_write_verify()
Clean the function up so that it's obvious what it is doing,
fix the formating strings in debug outputs, add kerneldoc.
Make the function return proper errno-compliant return values
and propagate this change throughout sdram.c
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sat, 1 Aug 2015 19:47:16 +0000 (21:47 +0200)]
ddr: altera: sdram: Clean up sdram_calculate_size() part 2
Clean up coding style, mostly clean up comments, add kerneldoc.
Also, zap assignment of the "cs" variable, which is outright
dead code, so just remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sat, 1 Aug 2015 19:44:00 +0000 (21:44 +0200)]
ddr: altera: sdram: Clean up sdram_calculate_size() part 1
Pluck out all of the CONFIG_HPS_SDR_CTRLCFG_* macros. This change
makes sdram.c completely clear of these macros and allows removing
of the ugly include of sdram.h . The namespace is now a much nicer
place!
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sat, 1 Aug 2015 19:35:18 +0000 (21:35 +0200)]
ddr: altera: sdram: Introduce socfpga_sdram_get_config()
Introduce socfpga_sdram_get_config() function implement in a board file,
which returns the socfpga_sdram_config structure. This is the last step
in cleaning up the socfpga_mmr_init_full(), but not the last step which
allows removing the inclusion of sdram.h from drivers/ddr/altera/sdram.c
thus far.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sat, 1 Aug 2015 20:25:29 +0000 (22:25 +0200)]
ddr: altera: sdram: Clean up sdram_mmr_init_full() part 8
Fix the return value so that standard errno return values can be used.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sat, 1 Aug 2015 20:03:48 +0000 (22:03 +0200)]
ddr: altera: sdram: Clean up sdram_mmr_init_full() part 7
Add kerneldoc.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sat, 1 Aug 2015 19:26:55 +0000 (21:26 +0200)]
ddr: altera: sdram: Clean up sdram_mmr_init_full() part 6
Pull out the block of register programming into a separate function.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sat, 1 Aug 2015 19:24:31 +0000 (21:24 +0200)]
ddr: altera: sdram: Clean up sdram_mmr_init_full() part 5
Rework remaining two register setting functions such that they only
return the final register value. Move the register setting into the
block of register I/O in sdram_mmr_init_full().
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sat, 1 Aug 2015 19:21:21 +0000 (21:21 +0200)]
ddr: altera: sdram: Clean up sdram_mmr_init_full() part 4
Merge sdr_set_*() functions which are just setting registers among
the sea of register setting in sdram_mmr_init_full(). There is no
need to keep them separate this way, there is nothing special about
them.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sat, 1 Aug 2015 19:16:20 +0000 (21:16 +0200)]
ddr: altera: sdram: Clean up sdram_mmr_init_full() part 3
Pluck out the remaining CONFIG_HPS_SDR_CTRLCFG_ and put it into
the socfpga_sdram_config structure.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sat, 1 Aug 2015 18:58:44 +0000 (20:58 +0200)]
ddr: altera: sdram: Clean up sdram_mmr_init_full() part 2
Suck out all the CONFIG_HPS_SDR_CTRLCFG_* from sdram_mmr_init_full()
into the socfpga_sdram_config structure. There is still one ugly
macro left behind, but this will be taken care of in subsequent patch.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sat, 1 Aug 2015 18:39:46 +0000 (20:39 +0200)]
ddr: altera: sdram: Clean up sdram_mmr_init_full() part 1
Zap all the ad-hoc readbacks from the registers and other useless
and broken debug output. This is really not useful and is only
confusing.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sat, 1 Aug 2015 18:30:10 +0000 (20:30 +0200)]
ddr: altera: sdram: Introduce socfpga_sdram_config() structure
Introduce this seemingly massive structure, which holds required values
of all the registers of the SDRAM controller. The idea here is to avoid
including the sdram.h header file, which is full of ad-hoc macros that
polute the global namespace. Once the cleanup of sdram.c would be complete
and all registers would be loaded from this new socfpga_sdram_config, a
board file will only pass this structure into the sdram.c . This will
hide all the horrors generated by QTS in the board directory.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sat, 1 Aug 2015 18:14:11 +0000 (20:14 +0200)]
ddr: altera: sdram: Clean up set_sdr_mp_threshold()
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sat, 1 Aug 2015 18:12:31 +0000 (20:12 +0200)]
ddr: altera: sdram: Clean up set_sdr_mp_pacing()
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sat, 1 Aug 2015 18:10:23 +0000 (20:10 +0200)]
ddr: altera: sdram: Clean up set_sdr_mp_weight()
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sat, 1 Aug 2015 18:04:33 +0000 (20:04 +0200)]
ddr: altera: sdram: Clean up set_sdr_fifo_cfg()
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sat, 1 Aug 2015 18:04:19 +0000 (20:04 +0200)]
ddr: altera: sdram: Clean up set_sdr_static_cfg()
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sat, 1 Aug 2015 17:50:56 +0000 (19:50 +0200)]
ddr: altera: sdram: Clean up set_sdr_addr_rw()
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sat, 1 Aug 2015 17:45:24 +0000 (19:45 +0200)]
ddr: altera: sdram: Clean up set_sdr_dram_timing*()
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
Merge set_sdr_dram_timing{1,2,3,4,lowpwr}() into single function
set_sdr_dram_timing() , since there's no point in keeping all this
stuff separate anymore.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sat, 1 Aug 2015 17:33:40 +0000 (19:33 +0200)]
ddr: altera: sdram: Clean up set_sdr_ctrlcfg()
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
The big plan here is to remove all the CONFIG_HPS_SDR_ macros, hide
them in QTS compatibility layer in board implementation and pass only
a small structure into the driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sat, 1 Aug 2015 17:20:19 +0000 (19:20 +0200)]
ddr: altera: sdram: Clean up compute_errata_rows() part 2
Remove all parameters of this function, since they are only constants
passed in from another function, so make them local. Also, rename the
function to get_errata_rows() as this is closer to what it does.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sat, 1 Aug 2015 16:54:34 +0000 (18:54 +0200)]
ddr: altera: sdram: Clean up compute_errata_rows() part 1
Clean up weird parenthesis and odd type casts from the function.
Fix comment style.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sat, 1 Aug 2015 16:46:55 +0000 (18:46 +0200)]
ddr: altera: sdram: Switch to generic_hweight32()
Use generic function instead of CPU-specific one.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Mon, 3 Aug 2015 16:31:51 +0000 (18:31 +0200)]
arm: socfpga: Add temporary workaround for missing SD/MMC patches
Add a small workaround into the platform code which forces the SDMMC
into 8-bit mode (the default configuration for all socfpga platforms)
to work around breakage caused by missing patches in mainline which
switch the probing of SD/MMC to OF instead of static configuraiton.
The patches will hit mainline after the SPL series, so to avoid build
issues, add this small temporary workaround.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sun, 26 Jul 2015 09:46:04 +0000 (11:46 +0200)]
ddr: altera: Clean up of delay_for_n_mem_clocks() part 5
Add kerneldoc.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sun, 26 Jul 2015 09:44:54 +0000 (11:44 +0200)]
ddr: altera: Clean up of delay_for_n_mem_clocks() part 4
Simplify the loop code, optimizing compiler can deal with this.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sun, 26 Jul 2015 09:42:53 +0000 (11:42 +0200)]
ddr: altera: Clean up of delay_for_n_mem_clocks() part 3
Clean up the computation of c_loop, outer and inner variables.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sun, 26 Jul 2015 09:34:09 +0000 (11:34 +0200)]
ddr: altera: Clean up of delay_for_n_mem_clocks() part 2
Factor out (afi_clocks - 1) into a single place instead of having it
all around the function.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sun, 26 Jul 2015 09:11:28 +0000 (11:11 +0200)]
ddr: altera: Clean up of delay_for_n_mem_clocks() part 1
Fix data types, clean up comments a bit and fix coding style a bit.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sun, 26 Jul 2015 08:59:19 +0000 (10:59 +0200)]
ddr: altera: Minor clean up of rw_mgr_mem_handoff()
Add kerneldoc and perform a minor comment cleanup.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Tue, 21 Jul 2015 04:18:57 +0000 (06:18 +0200)]
ddr: altera: Clean up rw_mgr_mem_calibrate_lfifo()
Minor coding style cleanup, add kerneldoc. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Sat, 18 Jul 2015 03:58:44 +0000 (05:58 +0200)]
ddr: altera: Clean up rw_mgr_mem_calibrate_vfifo_end()
This function is implementing the DDR calibration Stage 3 as
described in Altera EMI_RM 2015.05.04 . The main body of this
function is almost identical to Stage 1.3 (DQ/DQS centering)
for all but two flags -- use_read_test and update_fom. Convert
this function to call rw_mgr_mem_calibrate_dq_dqs_centering()
with the correct flags set to trim down the code duplication.
Moreover, reorder the remnants in the function a little and
convert the function to return either 0 or -EIO in case of
success and failure respectively, to match the common return
value convention.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Tue, 21 Jul 2015 04:00:36 +0000 (06:00 +0200)]
ddr: altera: Clean up rw_mgr_mem_calibrate_write_test_issue()
Brief clean, add kerneldoc.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Tue, 21 Jul 2015 03:57:11 +0000 (05:57 +0200)]
ddr: altera: Clean up rw_mgr_mem_calibrate_write_test() part 3
Add kerneldoc.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Tue, 21 Jul 2015 03:54:39 +0000 (05:54 +0200)]
ddr: altera: Clean up rw_mgr_mem_calibrate_write_test() part 2
Clean up coding style, mostly broken multiline formatting strings
in debug output. Also clean up data types and constify where applicable.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Tue, 21 Jul 2015 03:43:37 +0000 (05:43 +0200)]
ddr: altera: Clean up rw_mgr_mem_calibrate_write_test() part 1
Move code around to get rid of the forward declaration. No change
to the actual code.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Tue, 21 Jul 2015 03:33:49 +0000 (05:33 +0200)]
ddr: altera: Clean up rw_mgr_mem_calibrate_writes_center() part 5
Add kerneldoc.
Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Tue, 21 Jul 2015 03:32:49 +0000 (05:32 +0200)]
ddr: altera: Clean up rw_mgr_mem_calibrate_writes_center() part 4
Fix return values to match the common return value convention.
Signed-off-by: Marek Vasut <marex@denx.de>