Bluetooth: btrtl: add support for the RTL8723CS

[ Upstream commit c0123cb6c4c7fc2a42ead6cd7d3e82b8e1c25c6f ]

The Realtek RTL8723CS is a SDIO WiFi chip. It also contains a Bluetooth
module which is connected via UART to the host.

It shares lmp subversion with 8703B, so Realtek's userspace
initialization tool (rtk_hciattach) differentiates varieties of RTL8723CS
(CG, VF, XX) with RTL8703B using vendor's command to read chip type.

Also this chip declares support for some features it doesn't support
so add a quirk to indicate that these features are broken.

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Bastian Germann <bage@debian.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Bluetooth: Add new quirk for broken local ext features page 2

[ Upstream commit 8194f1ef5a815aea815a91daf2c721eab2674f1f ]

Some adapters (e.g. RTL8723CS) advertise that they have more than
2 pages for local ext features, but they don't support any features
declared in these pages. RTL8723CS reports max_page = 2 and declares
support for sync train and secure connection, but it responds with
either garbage or with error in status on corresponding commands.

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Bastian Germann <bage@debian.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Bluetooth: btusb: Add new PID/VID 04ca:3801 for MT7663

[ Upstream commit 13209415d0e88396d99d346b184864834d70d68a ]

This bluetooth device is found in a combo WLAN/BT card
for a MediaTek 7663.

Tested on Acer Aspire A315-24P Notebook

The device information:

T:  Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  2 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=04ca ProdID=3801 Rev= 1.00
S:  Manufacturer=MediaTek Inc.
S:  Product=Wireless_Device
S:  SerialNumber=000000000
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms

Signed-off-by: Meng Tang <tangmeng@uniontech.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ipvs: Update width of source for ip_vs_sync_conn_options

[ Upstream commit e3478c68f6704638d08f437cbc552ca5970c151a ]

In ip_vs_sync_conn_v0() copy is made to struct ip_vs_sync_conn_options.
That structure looks like this:

struct ip_vs_sync_conn_options {
        struct ip_vs_seq        in_seq;
        struct ip_vs_seq        out_seq;
};

The source of the copy is the in_seq field of struct ip_vs_conn.  Whose
type is struct ip_vs_seq. Thus we can see that the source - is not as
wide as the amount of data copied, which is the width of struct
ip_vs_sync_conn_option.

The copy is safe because the next field in is another struct ip_vs_seq.
Make use of struct_group() to annotate this.

Flagged by gcc-13 as:

 In file included from ./include/linux/string.h:254,
                  from ./include/linux/bitmap.h:11,
                  from ./include/linux/cpumask.h:12,
                  from ./arch/x86/include/asm/paravirt.h:17,
                  from ./arch/x86/include/asm/cpuid.h:62,
                  from ./arch/x86/include/asm/processor.h:19,
                  from ./arch/x86/include/asm/timex.h:5,
                  from ./include/linux/timex.h:67,
                  from ./include/linux/time32.h:13,
                  from ./include/linux/time.h:60,
                  from ./include/linux/stat.h:19,
                  from ./include/linux/module.h:13,
                  from net/netfilter/ipvs/ip_vs_sync.c:38:
 In function 'fortify_memcpy_chk',
     inlined from 'ip_vs_sync_conn_v0' at net/netfilter/ipvs/ip_vs_sync.c:606:3:
 ./include/linux/fortify-string.h:529:25: error: call to '__read_overflow2_field' declared with attribute warning: detected read beyond size of field (2nd parameter); maybe use struct_group()? [-Werror=attribute-warning]
   529 |                         __read_overflow2_field(q_size_field, size);
       |

Compile tested only.

Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nbd: fix incomplete validation of ioctl arg

[ Upstream commit 55793ea54d77719a071b1ccc05a05056e3b5e009 ]

We tested and found an alarm caused by nbd_ioctl arg without verification.
The UBSAN warning calltrace like below:

UBSAN: Undefined behaviour in fs/buffer.c:1709:35
signed integer overflow:
-9223372036854775808 - 1 cannot be represented in type 'long long int'
CPU: 3 PID: 2523 Comm: syz-executor.0 Not tainted 4.19.90 #1
Hardware name: linux,dummy-virt (DT)
Call trace:
 dump_backtrace+0x0/0x3f0 arch/arm64/kernel/time.c:78
 show_stack+0x28/0x38 arch/arm64/kernel/traps.c:158
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x170/0x1dc lib/dump_stack.c:118
 ubsan_epilogue+0x18/0xb4 lib/ubsan.c:161
 handle_overflow+0x188/0x1dc lib/ubsan.c:192
 __ubsan_handle_sub_overflow+0x34/0x44 lib/ubsan.c:206
 __block_write_full_page+0x94c/0xa20 fs/buffer.c:1709
 block_write_full_page+0x1f0/0x280 fs/buffer.c:2934
 blkdev_writepage+0x34/0x40 fs/block_dev.c:607
 __writepage+0x68/0xe8 mm/page-writeback.c:2305
 write_cache_pages+0x44c/0xc70 mm/page-writeback.c:2240
 generic_writepages+0xdc/0x148 mm/page-writeback.c:2329
 blkdev_writepages+0x2c/0x38 fs/block_dev.c:2114
 do_writepages+0xd4/0x250 mm/page-writeback.c:2344

The reason for triggering this warning is __block_write_full_page()
-> i_size_read(inode) - 1 overflow.
inode->i_size is assigned in __nbd_ioctl() -> nbd_set_size() -> bytesize.
We think it is necessary to limit the size of arg to prevent errors.

Moreover, __nbd_ioctl() -> nbd_add_socket(), arg will be cast to int.
Assuming the value of arg is 0x80000000000000001) (on a 64-bit machine),
it will become 1 after the coercion, which will return unexpected results.

Fix it by adding checks to prevent passing in too large numbers.

Signed-off-by: Zhong Jinghua <zhongjinghua@huawei.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Link: https://lore.kernel.org/r/20230206145805.2645671-1-zhongjinghua@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

wifi: ath11k: Fix SKB corruption in REO destination ring

[ Upstream commit f9fff67d2d7ca6fa8066132003a3deef654c55b1 ]

While running traffics for a long time, randomly an RX descriptor
filled with value "0" from REO destination ring is received.
This descriptor which is invalid causes the wrong SKB (SKB stored in
the IDR lookup with buffer id "0") to be fetched which in turn
causes SKB memory corruption issue and the same leads to crash
after some time.

Changed the start id for idr allocation to "1" and the buffer id "0"
is reserved for error validation. Introduced Sanity check to validate
the descriptor, before processing the SKB.

Crash Signature :

Unable to handle kernel paging request at virtual address 3f004900
PC points to "b15_dma_inv_range+0x30/0x50"
LR points to "dma_cache_maint_page+0x8c/0x128".
The Backtrace obtained is as follows:
[<8031716c>] (b15_dma_inv_range) from [<80313a4c>] (dma_cache_maint_page+0x8c/0x128)
[<80313a4c>] (dma_cache_maint_page) from [<80313b90>] (__dma_page_dev_to_cpu+0x28/0xcc)
[<80313b90>] (__dma_page_dev_to_cpu) from [<7fb5dd68>] (ath11k_dp_process_rx+0x1e8/0x4a4 [ath11k])
[<7fb5dd68>] (ath11k_dp_process_rx [ath11k]) from [<7fb53c20>] (ath11k_dp_service_srng+0xb0/0x2ac [ath11k])
[<7fb53c20>] (ath11k_dp_service_srng [ath11k]) from [<7f67bba4>] (ath11k_pci_ext_grp_napi_poll+0x1c/0x78 [ath11k_pci])
[<7f67bba4>] (ath11k_pci_ext_grp_napi_poll [ath11k_pci]) from [<807d5cf4>] (__napi_poll+0x28/0xb8)
[<807d5cf4>] (__napi_poll) from [<807d5f28>] (net_rx_action+0xf0/0x280)
[<807d5f28>] (net_rx_action) from [<80302148>] (__do_softirq+0xd0/0x280)
[<80302148>] (__do_softirq) from [<80320408>] (irq_exit+0x74/0xd4)
[<80320408>] (irq_exit) from [<803638a4>] (__handle_domain_irq+0x90/0xb4)
[<803638a4>] (__handle_domain_irq) from [<805bedec>] (gic_handle_irq+0x58/0x90)
[<805bedec>] (gic_handle_irq) from [<80301a78>] (__irq_svc+0x58/0x8c)

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1

Signed-off-by: Nagarajan Maran <quic_nmaran@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230403191533.28114-1-quic_nmaran@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

wifi: iwlwifi: dvm: Fix memcpy: detected field-spanning write backtrace

[ Upstream commit ef16799640865f937719f0771c93be5dca18adc6 ]

A received TKIP key may be up to 32 bytes because it may contain
MIC rx/tx keys too. These are not used by iwl and copying these
over overflows the iwl_keyinfo.key field.

Add a check to not copy more data to iwl_keyinfo.key then will fit.

This fixes backtraces like this one:

 memcpy: detected field-spanning write (size 32) of single field "sta_cmd.key.key" at drivers/net/wireless/intel/iwlwifi/dvm/sta.c:1103 (size 16)
 WARNING: CPU: 1 PID: 946 at drivers/net/wireless/intel/iwlwifi/dvm/sta.c:1103 iwlagn_send_sta_key+0x375/0x390 [iwldvm]
 <snip>
 Hardware name: Dell Inc. Latitude E6430/0H3MT5, BIOS A21 05/08/2017
 RIP: 0010:iwlagn_send_sta_key+0x375/0x390 [iwldvm]
 <snip>
 Call Trace:
  <TASK>
  iwl_set_dynamic_key+0x1f0/0x220 [iwldvm]
  iwlagn_mac_set_key+0x1e4/0x280 [iwldvm]
  drv_set_key+0xa4/0x1b0 [mac80211]
  ieee80211_key_enable_hw_accel+0xa8/0x2d0 [mac80211]
  ieee80211_key_replace+0x22d/0x8e0 [mac80211]
 <snip>

Link: https://www.alionet.org/index.php?topic=1469.0
Link: https://lore.kernel.org/linux-wireless/20230218191056.never.374-kees@kernel.org/
Link: https://lore.kernel.org/linux-wireless/68760035-7f75-1b23-e355-bfb758a87d83@redhat.com/
Cc: Kees Cook <keescook@chromium.org>
Suggested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

null_blk: Always check queue mode setting from configfs

[ Upstream commit 63f8793ee60513a09f110ea460a6ff2c33811cdb ]

Make sure to check device queue mode in the null_validate_conf() and
return error for NULL_Q_RQ as we don't allow legacy I/O path, without
this patch we get OOPs when queue mode is set to 1 from configfs,
following are repro steps :-

modprobe null_blk nr_devices=0
mkdir config/nullb/nullb0
echo 1 > config/nullb/nullb0/memory_backed
echo 4096 > config/nullb/nullb0/blocksize
echo 20480 > config/nullb/nullb0/size
echo 1 > config/nullb/nullb0/queue_mode
echo 1 > config/nullb/nullb0/power

Entering kdb (current=0xffff88810acdd080, pid 2372) on processor 42 Oops: (null)
due to oops @ 0xffffffffc041c329
CPU: 42 PID: 2372 Comm: sh Tainted: G           O     N 6.3.0-rc5lblk+ #5
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014
RIP: 0010:null_add_dev.part.0+0xd9/0x720 [null_blk]
Code: 01 00 00 85 d2 0f 85 a1 03 00 00 48 83 bb 08 01 00 00 00 0f 85 f7 03 00 00 80 bb 62 01 00 00 00 48 8b 75 20 0f 85 6d 02 00 00 <48> 89 6e 60 48 8b 75 20 bf 06 00 00 00 e8 f5 37 2c c1 48 8b 75 20
RSP: 0018:ffffc900052cbde0 EFLAGS: 00010246
RAX: 0000000000000001 RBX: ffff88811084d800 RCX: 0000000000000001
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff888100042e00
RBP: ffff8881053d8200 R08: ffffc900052cbd68 R09: ffff888105db2000
R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000002
R13: ffff888104765200 R14: ffff88810eec1748 R15: ffff88810eec1740
FS:  00007fd445fd1740(0000) GS:ffff8897dfc80000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000060 CR3: 0000000166a00000 CR4: 0000000000350ee0
DR0: ffffffff8437a488 DR1: ffffffff8437a489 DR2: ffffffff8437a48a
DR3: ffffffff8437a48b DR6: 00000000ffff0ff0 DR7: 0000000000000400
Call Trace:
 <TASK>
 nullb_device_power_store+0xd1/0x120 [null_blk]
 configfs_write_iter+0xb4/0x120
 vfs_write+0x2ba/0x3c0
 ksys_write+0x5f/0xe0
 do_syscall_64+0x3b/0x90
 entry_SYSCALL_64_after_hwframe+0x72/0xdc
RIP: 0033:0x7fd4460c57a7
Code: 0d 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b7 0f 1f 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 48 89 54 24 18 48 89 74 24
RSP: 002b:00007ffd3792a4a8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000000000000002 RCX: 00007fd4460c57a7
RDX: 0000000000000002 RSI: 000055b43c02e4c0 RDI: 0000000000000001
RBP: 000055b43c02e4c0 R08: 000000000000000a R09: 00007fd44615b4e0
R10: 00007fd44615b3e0 R11: 0000000000000246 R12: 0000000000000002
R13: 00007fd446198520 R14: 0000000000000002 R15: 00007fd446198700
 </TASK>

Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Nitesh Shetty <nj.shetty@samsung.com>
Link: https://lore.kernel.org/r/20230416220339.43845-1-kch@nvidia.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

wifi: iwlwifi: fix iwl_mvm_max_amsdu_size() for MLO

[ Upstream commit b2bc600cced23762d4e97db8989b18772145604f ]

For MLO, we cannot use vif->bss_conf.chandef.chan->band, since
that will lead to a NULL-ptr dereference as bss_conf isn't used.
However, in case of real MLO, we also need to take both LMACs
into account if they exist, since the station might be active
on both LMACs at the same time.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230417113648.3588afc85d79.I11592893bbc191b9548518b8bd782de568a9f848@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

wifi: ath11k: Ignore frags from uninitialized peer in dp.

[ Upstream commit a06bfb3c9f69f303692cdae87bc0899d2ae8b2a6 ]

When max virtual ap interfaces are configured in all the bands with
ACS and hostapd restart is done every 60s, a crash is observed at
random times.
In this certain scenario, a fragmented packet is received for
self peer, for which rx_tid and rx_frags are not initialized in
datapath. While handling this fragment, crash is observed as the
rx_frag list is uninitialised and when we walk in
ath11k_dp_rx_h_sort_frags, skb null leads to exception.

To address this, before processing received fragments we check
dp_setup_done flag is set to ensure that peer has completed its
dp peer setup for fragment queue, else ignore processing the
fragments.

Call trace:
  ath11k_dp_process_rx_err+0x550/0x1084 [ath11k]
  ath11k_dp_service_srng+0x70/0x370 [ath11k]
  0xffffffc009693a04
  __napi_poll+0x30/0xa4
  net_rx_action+0x118/0x270
  __do_softirq+0x10c/0x244
  irq_exit+0x64/0xb4
  __handle_domain_irq+0x88/0xac
  gic_handle_irq+0x74/0xbc
  el1_irq+0xf0/0x1c0
  arch_cpu_idle+0x10/0x18
  do_idle+0x104/0x248
  cpu_startup_entry+0x20/0x64
  rest_init+0xd0/0xdc
  arch_call_rest_init+0xc/0x14
  start_kernel+0x480/0x4b8
  Code: f9400281 f94066a2 91405021 b94a0023 (f9406401)

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1

Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Nagarajan Maran <quic_nmaran@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230403184155.8670-2-quic_nmaran@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

block, bfq: Fix division by zero error on zero wsum

[ Upstream commit e53413f8deedf738a6782cc14cc00bd5852ccf18 ]

When the weighted sum is zero the calculation of limit causes
a division by zero error. Fix this by continuing to the next level.

This was discovered by running as root:

stress-ng --ioprio 0

Fixes divison by error oops:

[  521.450556] divide error: 0000 [#1] SMP NOPTI
[  521.450766] CPU: 2 PID: 2684464 Comm: stress-ng-iopri Not tainted 6.2.1-1280.native #1
[  521.451117] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.1-0-g3208b098f51a-prebuilt.qemu.org 04/01/2014
[  521.451627] RIP: 0010:bfqq_request_over_limit+0x207/0x400
[  521.451875] Code: 01 48 8d 0c c8 74 0b 48 8b 82 98 00 00 00 48 8d 0c c8 8b 85 34 ff ff ff 48 89 ca 41 0f af 41 50 48 d1 ea 48 98 48 01 d0 31 d2 <48> f7 f1 41 39 41 48 89 85 34 ff ff ff 0f 8c 7b 01 00 00 49 8b 44
[  521.452699] RSP: 0018:ffffb1af84eb3948 EFLAGS: 00010046
[  521.452938] RAX: 000000000000003c RBX: 0000000000000000 RCX: 0000000000000000
[  521.453262] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffb1af84eb3978
[  521.453584] RBP: ffffb1af84eb3a30 R08: 0000000000000001 R09: ffff8f88ab8a4ba0
[  521.453905] R10: 0000000000000000 R11: 0000000000000001 R12: ffff8f88ab8a4b18
[  521.454224] R13: ffff8f8699093000 R14: 0000000000000001 R15: ffffb1af84eb3970
[  521.454549] FS:  00005640b6b0b580(0000) GS:ffff8f88b3880000(0000) knlGS:0000000000000000
[  521.454912] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  521.455170] CR2: 00007ffcbcae4e38 CR3: 00000002e46de001 CR4: 0000000000770ee0
[  521.455491] PKRU: 55555554
[  521.455619] Call Trace:
[  521.455736]  <TASK>
[  521.455837]  ? bfq_request_merge+0x3a/0xc0
[  521.456027]  ? elv_merge+0x115/0x140
[  521.456191]  bfq_limit_depth+0xc8/0x240
[  521.456366]  __blk_mq_alloc_requests+0x21a/0x2c0
[  521.456577]  blk_mq_submit_bio+0x23c/0x6c0
[  521.456766]  __submit_bio+0xb8/0x140
[  521.457236]  submit_bio_noacct_nocheck+0x212/0x300
[  521.457748]  submit_bio_noacct+0x1a6/0x580
[  521.458220]  submit_bio+0x43/0x80
[  521.458660]  ext4_io_submit+0x23/0x80
[  521.459116]  ext4_do_writepages+0x40a/0xd00
[  521.459596]  ext4_writepages+0x65/0x100
[  521.460050]  do_writepages+0xb7/0x1c0
[  521.460492]  __filemap_fdatawrite_range+0xa6/0x100
[  521.460979]  file_write_and_wait_range+0xbf/0x140
[  521.461452]  ext4_sync_file+0x105/0x340
[  521.461882]  __x64_sys_fsync+0x67/0x100
[  521.462305]  ? syscall_exit_to_user_mode+0x2c/0x1c0
[  521.462768]  do_syscall_64+0x3b/0xc0
[  521.463165]  entry_SYSCALL_64_after_hwframe+0x5a/0xc4
[  521.463621] RIP: 0033:0x5640b6c56590
[  521.464006] Code: 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 80 3d 71 70 0e 00 00 74 17 b8 4a 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 48 c3 0f 1f 80 00 00 00 00 48 83 ec 18 89 7c

Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20230413133009.1605335-1-colin.i.king@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

wifi: iwlwifi: mvm: fix ptk_pn memory leak

[ Upstream commit d066a530af8e1833c7ea2cef7784004700c85f79 ]

If adding a key to firmware fails we leak the allocated ptk_pn.
This shouldn't happen in practice, but we should still fix it.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230414130637.99446ffd02bc.I82a2ad6ec1395f188e0a1677cc619e3fcb1feac9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

wifi: iwlwifi: pcie: Fix integer overflow in iwl_write_to_user_buf

[ Upstream commit 58d1b717879bfeabe09b35e41ad667c79933eb2e ]

An integer overflow occurs in the iwl_write_to_user_buf() function,
which is called by the iwl_dbgfs_monitor_data_read() function.

static bool iwl_write_to_user_buf(char __user *user_buf, ssize_t count,
  void *buf, ssize_t *size,
  ssize_t *bytes_copied)
{
int buf_size_left = count - *bytes_copied;

buf_size_left = buf_size_left - (buf_size_left % sizeof(u32));
if (*size > buf_size_left)
*size = buf_size_left;

If the user passes a SIZE_MAX value to the "ssize_t count" parameter,
the ssize_t count parameter is assigned to "int buf_size_left".
Then compare "*size" with "buf_size_left" . Here, "buf_size_left" is a
negative number, so "*size" is assigned "buf_size_left" and goes into
the third argument of the copy_to_user function, causing a heap overflow.

This is not a security vulnerability because iwl_dbgfs_monitor_data_read()
is a debugfs operation with 0400 privileges.

Signed-off-by: Hyunwoo Kim <imv4bel@gmail.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230414130637.2d80ace81532.Iecfba549e0e0be21bbb0324675392e42e75bd5ad@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

wifi: iwlwifi: add a new PCI device ID for BZ device

[ Upstream commit c30a2a64788b3d617a9c5d96adb76c68b0862e5f ]

Add support for a new PCI device ID 0x272b once registering with PCIe.

Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230414130637.56342664110d.I5aa6f2858fdcf69fdea4f1a873115a48bd43764e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

wifi: iwlwifi: pcie: fix possible NULL pointer dereference

[ Upstream commit b655b9a9f8467684cfa8906713d33b71ea8c8f54 ]

It is possible that iwl_pci_probe() will fail and free the trans,
then afterwards iwl_pci_remove() will be called and crash by trying
to access trans which is already freed, fix it.

iwlwifi 0000:01:00.0: Detected crf-id 0xa5a5a5a2, cnv-id 0xa5a5a5a2
      wfpm id 0xa5a5a5a2
iwlwifi 0000:01:00.0: Can't find a correct rfid for crf id 0x5a2
...
BUG: kernel NULL pointer dereference, address: 0000000000000028
...
RIP: 0010:iwl_pci_remove+0x12/0x30 [iwlwifi]
pci_device_remove+0x3e/0xb0
device_release_driver_internal+0x103/0x1f0
driver_detach+0x4c/0x90
bus_remove_driver+0x5c/0xd0
driver_unregister+0x31/0x50
pci_unregister_driver+0x40/0x90
iwl_pci_unregister_driver+0x15/0x20 [iwlwifi]
__exit_compat+0x9/0x98 [iwlwifi]
__x64_sys_delete_module+0x147/0x260

Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413213309.082f6e21341b.I0db21d7fa9a828d571ca886713bd0b5d0b6e1e5c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

md: fix soft lockup in status_resync

[ Upstream commit 6efddf1e32e2a264694766ca485a4f5e04ee82a7 ]

status_resync() will calculate 'curr_resync - recovery_active' to show
user a progress bar like following:

[============>........]  resync = 61.4%

'curr_resync' and 'recovery_active' is updated in md_do_sync(), and
status_resync() can read them concurrently, hence it's possible that
'curr_resync - recovery_active' can overflow to a huge number. In this
case status_resync() will be stuck in the loop to print a large amount
of '=', which will end up soft lockup.

Fix the problem by setting 'resync' to MD_RESYNC_ACTIVE in this case,
this way resync in progress will be reported to user.

Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230310073855.1337560-3-yukuai1@huaweicloud.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

bpf: Add preempt_count_{sub,add} into btf id deny list

[ Upstream commit c11bd046485d7bf1ca200db0e7d0bdc4bafdd395 ]

The recursion check in __bpf_prog_enter* and __bpf_prog_exit*
leave preempt_count_{sub,add} unprotected. When attaching trampoline to
them we get panic as follows,

[  867.843050] BUG: TASK stack guard page was hit at 0000000009d325cf (stack is 0000000046a46a15..00000000537e7b28)
[  867.843064] stack guard page: 0000 [#1] PREEMPT SMP NOPTI
[  867.843067] CPU: 8 PID: 11009 Comm: trace Kdump: loaded Not tainted 6.2.0+ #4
[  867.843100] Call Trace:
[  867.843101]  <TASK>
[  867.843104]  asm_exc_int3+0x3a/0x40
[  867.843108] RIP: 0010:preempt_count_sub+0x1/0xa0
[  867.843135]  __bpf_prog_enter_recur+0x17/0x90
[  867.843148]  bpf_trampoline_6442468108_0+0x2e/0x1000
[  867.843154]  ? preempt_count_sub+0x1/0xa0
[  867.843157]  preempt_count_sub+0x5/0xa0
[  867.843159]  ? migrate_enable+0xac/0xf0
[  867.843164]  __bpf_prog_exit_recur+0x2d/0x40
[  867.843168]  bpf_trampoline_6442468108_0+0x55/0x1000
...
[  867.843788]  preempt_count_sub+0x5/0xa0
[  867.843793]  ? migrate_enable+0xac/0xf0
[  867.843829]  __bpf_prog_exit_recur+0x2d/0x40
[  867.843837] BUG: IRQ stack guard page was hit at 0000000099bd8228 (stack is 00000000b23e2bc4..000000006d95af35)
[  867.843841] BUG: IRQ stack guard page was hit at 000000005ae07924 (stack is 00000000ffd69623..0000000014eb594c)
[  867.843843] BUG: IRQ stack guard page was hit at 00000000028320f0 (stack is 00000000034b6438..0000000078d1bcec)
[  867.843842]  bpf_trampoline_6442468108_0+0x55/0x1000
...

That is because in __bpf_prog_exit_recur, the preempt_count_{sub,add} are
called after prog->active is decreased.

Fixing this by adding these two functions into btf ids deny list.

Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Yafang <laoar.shao@gmail.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Jiri Olsa <olsajiri@gmail.com>
Acked-by: Hao Luo <haoluo@google.com>
Link: https://lore.kernel.org/r/20230413025248.79764-1-laoar.shao@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

samples/bpf: Fix fout leak in hbm's run_bpf_prog

[ Upstream commit 23acb14af1914010dd0aae1bbb7fab28bf518b8e ]

Fix fout being fopen'ed but then not subsequently fclose'd. In the affected
branch, fout is otherwise going out of scope.

Signed-off-by: Hao Zeng <zenghao@kylinos.cn>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20230411084349.1999628-1-zenghao@kylinos.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>

f2fs: fix to check readonly condition correctly

[ Upstream commit d78dfefcde9d311284434560d69c0478c55a657e ]

With below case, it can mount multi-device image w/ rw option, however
one of secondary device is set as ro, later update will cause panic, so
let's introduce f2fs_dev_is_readonly(), and check multi-devices rw status
in f2fs_remount() w/ it in order to avoid such inconsistent mount status.

mkfs.f2fs -c /dev/zram1 /dev/zram0 -f
blockdev --setro /dev/zram1
mount -t f2fs dev/zram0 /mnt/f2fs
mount: /mnt/f2fs: WARNING: source write-protected, mounted read-only.
mount -t f2fs -o remount,rw mnt/f2fs
dd if=/dev/zero  of=/mnt/f2fs/file bs=1M count=8192

kernel BUG at fs/f2fs/inline.c:258!
RIP: 0010:f2fs_write_inline_data+0x23e/0x2d0 [f2fs]
Call Trace:
  f2fs_write_single_data_page+0x26b/0x9f0 [f2fs]
  f2fs_write_cache_pages+0x389/0xa60 [f2fs]
  __f2fs_write_data_pages+0x26b/0x2d0 [f2fs]
  f2fs_write_data_pages+0x2e/0x40 [f2fs]
  do_writepages+0xd3/0x1b0
  __writeback_single_inode+0x5b/0x420
  writeback_sb_inodes+0x236/0x5a0
  __writeback_inodes_wb+0x56/0xf0
  wb_writeback+0x2a3/0x490
  wb_do_writeback+0x2b2/0x330
  wb_workfn+0x6a/0x260
  process_one_work+0x270/0x5e0
  worker_thread+0x52/0x3e0
  kthread+0xf4/0x120
  ret_from_fork+0x29/0x50

Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

f2fs: fix to drop all dirty pages during umount() if cp_error is set

[ Upstream commit c9b3649a934d131151111354bcbb638076f03a30 ]

xfstest generic/361 reports a bug as below:

f2fs_bug_on(sbi, sbi->fsync_node_num);

kernel BUG at fs/f2fs/super.c:1627!
RIP: 0010:f2fs_put_super+0x3a8/0x3b0
Call Trace:
 generic_shutdown_super+0x8c/0x1b0
 kill_block_super+0x2b/0x60
 kill_f2fs_super+0x87/0x110
 deactivate_locked_super+0x39/0x80
 deactivate_super+0x46/0x50
 cleanup_mnt+0x109/0x170
 __cleanup_mnt+0x16/0x20
 task_work_run+0x65/0xa0
 exit_to_user_mode_prepare+0x175/0x190
 syscall_exit_to_user_mode+0x25/0x50
 do_syscall_64+0x4c/0x90
 entry_SYSCALL_64_after_hwframe+0x72/0xdc

During umount(), if cp_error is set, f2fs_wait_on_all_pages() should
not stop waiting all F2FS_WB_CP_DATA pages to be writebacked, otherwise,
fsync_node_num can be non-zero after f2fs_wait_on_all_pages() causing
this bug.

In this case, to avoid deadloop in f2fs_wait_on_all_pages(), it needs
to drop all dirty pages rather than redirtying them.

Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

f2fs: Fix system crash due to lack of free space in LFS

[ Upstream commit d11cef14f8146f3babd286c2cc8ca09c166295e2 ]

When f2fs tries to checkpoint during foreground gc in LFS mode, system
crash occurs due to lack of free space if the amount of dirty node and
dentry pages generated by data migration exceeds free space.
The reproduction sequence is as follows.

 - 20GiB capacity block device (null_blk)
 - format and mount with LFS mode
 - create a file and write 20,000MiB
 - 4k random write on full range of the file

 RIP: 0010:new_curseg+0x48a/0x510 [f2fs]
 Code: 55 e7 f5 89 c0 48 0f af c3 48 8b 5d c0 48 c1 e8 20 83 c0 01 89 43 6c 48 83 c4 28 5b 41 5c 41 5d 41 5e 41 5f 5d c3 cc cc cc cc <0f> 0b f0 41 80 4f 48 04 45 85 f6 0f 84 ba fd ff ff e9 ef fe ff ff
 RSP: 0018:ffff977bc397b218 EFLAGS: 00010246
 RAX: 00000000000027b9 RBX: 0000000000000000 RCX: 00000000000027c0
 RDX: 0000000000000000 RSI: 00000000000027b9 RDI: ffff8c25ab4e74f8
 RBP: ffff977bc397b268 R08: 00000000000027b9 R09: ffff8c29e4a34b40
 R10: 0000000000000001 R11: ffff977bc397b0d8 R12: 0000000000000000
 R13: ffff8c25b4dd81a0 R14: 0000000000000000 R15: ffff8c2f667f9000
 FS: 0000000000000000(0000) GS:ffff8c344ec80000(0000) knlGS:0000000000000000
 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 000000c00055d000 CR3: 0000000e30810003 CR4: 00000000003706e0
 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
 Call Trace:
 <TASK>
 allocate_segment_by_default+0x9c/0x110 [f2fs]
 f2fs_allocate_data_block+0x243/0xa30 [f2fs]
 ? __mod_lruvec_page_state+0xa0/0x150
 do_write_page+0x80/0x160 [f2fs]
 f2fs_do_write_node_page+0x32/0x50 [f2fs]
 __write_node_page+0x339/0x730 [f2fs]
 f2fs_sync_node_pages+0x5a6/0x780 [f2fs]
 block_operations+0x257/0x340 [f2fs]
 f2fs_write_checkpoint+0x102/0x1050 [f2fs]
 f2fs_gc+0x27c/0x630 [f2fs]
 ? folio_mark_dirty+0x36/0x70
 f2fs_balance_fs+0x16f/0x180 [f2fs]

This patch adds checking whether free sections are enough before checkpoint
during gc.

Signed-off-by: Yonggil Song <yonggil.song@samsung.com>
[Jaegeuk Kim: code clean-up]
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

crypto: jitter - permanent and intermittent health errors

[ Upstream commit 3fde2fe99aa6dacd4151c87382b07ce7f30f0a52 ]

According to SP800-90B, two health failures are allowed: the intermittend
and the permanent failure. So far, only the intermittent failure was
implemented. The permanent failure was achieved by resetting the entire
entropy source including its health test state and waiting for two or
more back-to-back health errors.

This approach is appropriate for RCT, but not for APT as APT has a
non-linear cutoff value. Thus, this patch implements 2 cutoff values
for both RCT/APT. This implies that the health state is left untouched
when an intermittent failure occurs. The noise source is reset
and a new APT powerup-self test is performed. Yet, whith the unchanged
health test state, the counting of failures continues until a permanent
failure is reached.

Any non-failing raw entropy value causes the health tests to reset.

The intermittent error has an unchanged significance level of 2^-30.
The permanent error has a significance level of 2^-60. Considering that
this level also indicates a false-positive rate (see SP800-90B section 4.2)
a false-positive must only be incurred with a low probability when
considering a fleet of Linux kernels as a whole. Hitting the permanent
error may cause a panic(), the following calculation applies: Assuming
that a fleet of 10^9 Linux kernels run concurrently with this patch in
FIPS mode and on each kernel 2 health tests are performed every minute
for one year, the chances of a false positive is about 1:1000
based on the binomial distribution.

In addition, any power-up health test errors triggered with
jent_entropy_init are treated as permanent errors.

A permanent failure causes the entire entropy source to permanently
return an error. This implies that a caller can only remedy the situation
by re-allocating a new instance of the Jitter RNG. In a subsequent
patch, a transparent re-allocation will be provided which also changes
the implied heuristic entropy assessment.

In addition, when the kernel is booted with fips=1, the Jitter RNG
is defined to be part of a FIPS module. The permanent error of the
Jitter RNG is translated as a FIPS module error. In this case, the entire
FIPS module must cease operation. This is implemented in the kernel by
invoking panic().

The patch also fixes an off-by-one in the RCT cutoff value which is now
set to 30 instead of 31. This is because the counting of the values
starts with 0.

Reviewed-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Reviewed-by: Marcelo Henrique Cerri <marcelo.cerri@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ext4: Fix best extent lstart adjustment logic in ext4_mb_new_inode_pa()

[ Upstream commit 93cdf49f6eca5e23f6546b8f28457b2e6a6961d9 ]

When the length of best extent found is less than the length of goal extent
we need to make sure that the best extent atleast covers the start of the
original request. This is done by adjusting the ac_b_ex.fe_logical (logical
start) of the extent.

While doing so, the current logic sometimes results in the best extent's
logical range overflowing the goal extent. Since this best extent is later
added to the inode preallocation list, we have a possibility of introducing
overlapping preallocations. This is discussed in detail here [1].

As per Jan's suggestion, to fix this, replace the existing logic with the
below logic for adjusting best extent as it keeps fragmentation in check
while ensuring logical range of best extent doesn't overflow out of goal
extent:

1. Check if best extent can be kept at end of goal range and still cover
   original start.
2. Else, check if best extent can be kept at start of goal range and still
   cover original start.
3. Else, keep the best extent at start of original request.

Also, add a few extra BUG_ONs that might help catch errors faster.

[1] https://lore.kernel.org/r/Y+OGkVvzPN0RMv0O@li-bb2b2a4c-3307-11b2-a85c-8fa5c3a69313.ibm.com

Suggested-by: Jan Kara <jack@suse.cz>
Signed-off-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Reviewed-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/f96aca6d415b36d1f90db86c1a8cd7e2e9d7ab0e.1679731817.git.ojaswin@linux.ibm.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ext4: set goal start correctly in ext4_mb_normalize_request

[ Upstream commit b07ffe6927c75d99af534d685282ea188d9f71a6 ]

We need to set ac_g_ex to notify the goal start used in
ext4_mb_find_by_goal. Set ac_g_ex instead of ac_f_ex in
ext4_mb_normalize_request.
Besides we should assure goal start is in range [first_data_block,
blocks_count) as ext4_mb_initialize_context does.

[ Added a check to make sure size is less than ar->pright; otherwise
  we could end up passing an underflowed value of ar->pright - size to
  ext4_get_group_no_and_offset(), which will trigger a BUG_ON later on.
  - TYT ]

Signed-off-by: Kemeng Shi <shikemeng@huaweicloud.com>
Reviewed-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com>
Link: https://lore.kernel.org/r/20230303172120.3800725-2-shikemeng@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: ufs: ufs-pci: Add support for Intel Lunar Lake

[ Upstream commit 0a07d3c7a1d205b47d9f3608ff4e9d1065d63b6d ]

Add PCI ID to support Intel Lunar Lake, same as MTL.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230328105832.3495-1-adrian.hunter@intel.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

gfs2: Fix inode height consistency check

[ Upstream commit cfcdb5bad34f600aed7613c3c1a5e618111f77b7 ]

The maximum allowed height of an inode's metadata tree depends on the
filesystem block size; it is lower for bigger-block filesystems.  When
reading in an inode, make sure that the height doesn't exceed the
maximum allowed height.

Arrays like sd_heightsize are sized to be big enough for any filesystem
block size; they will often be slightly bigger than what's needed for a
specific filesystem.

Reported-by: syzbot+45d4691b1ed3c48eba05@syzkaller.appspotmail.com
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: message: mptlan: Fix use after free bug in mptlan_remove() due to race condition

[ Upstream commit f486893288f3e9b171b836f43853a6426515d800 ]

mptlan_probe() calls mpt_register_lan_device() which initializes the
&priv->post_buckets_task workqueue. A call to
mpt_lan_wake_post_buckets_task() will subsequently start the work.

During driver unload in mptlan_remove() the following race may occur:

CPU0                  CPU1

                    |mpt_lan_post_receive_buckets_work()
mptlan_remove()     |
  free_netdev()     |
    kfree(dev);     |
                    |
                    | dev->mtu
                    |   //use

Fix this by finishing the work prior to cleaning up in mptlan_remove().

[mkp: we really should remove mptlan instead of attempting to fix it]

Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Link: https://lore.kernel.org/r/20230318081635.796479-1-zyytlz.wz@163.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

lib: cpu_rmap: Avoid use after free on rmap->obj array entries

[ Upstream commit 4e0473f1060aa49621d40a113afde24818101d37 ]

When calling irq_set_affinity_notifier() with NULL at the notify
argument, it will cause freeing of the glue pointer in the
corresponding array entry but will leave the pointer in the array. A
subsequent call to free_irq_cpu_rmap() will try to free this entry again
leading to possible use after free.

Fix that by setting NULL to the array entry and checking that we have
non-zero at the array entry when iterating over the array in
free_irq_cpu_rmap().

The current code does not suffer from this since there are no cases
where irq_set_affinity_notifier(irq, NULL) (note the NULL passed for the
notify arg) is called, followed by a call to free_irq_cpu_rmap() so we
don't hit and issue. Subsequent patches in this series excersize this
flow, hence the required fix.

Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: target: iscsit: Free cmds before session free

[ Upstream commit d8990b5a4d065f38f35d69bcd627ec5a7f8330ca ]

Commands from recovery entries are freed after session has been closed.
That leads to use-after-free at command free or NPE with such call trace:

Time2Retain timer expired for SID: 1, cleaning up iSCSI session.
BUG: kernel NULL pointer dereference, address: 0000000000000140
RIP: 0010:sbitmap_queue_clear+0x3a/0xa0
Call Trace:
 target_release_cmd_kref+0xd1/0x1f0 [target_core_mod]
 transport_generic_free_cmd+0xd1/0x180 [target_core_mod]
 iscsit_free_cmd+0x53/0xd0 [iscsi_target_mod]
 iscsit_free_connection_recovery_entries+0x29d/0x320 [iscsi_target_mod]
 iscsit_close_session+0x13a/0x140 [iscsi_target_mod]
 iscsit_check_post_dataout+0x440/0x440 [iscsi_target_mod]
 call_timer_fn+0x24/0x140

Move cleanup of recovery enrties to before session freeing.

Reported-by: Forza <forza@tnonline.net>
Signed-off-by: Dmitry Bogdanov <d.bogdanov@yadro.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20230319015620.96006-7-michael.christie@oracle.com
Reviewed-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netdev: Enforce index cap in netdev_get_tx_queue

[ Upstream commit 1cc6571f562774f1d928dc8b3cff50829b86e970 ]

When requesting a TX queue at a given index, warn on out-of-bounds
referencing if the index is greater than the allocated number of
queues.

Specifically, since this function is used heavily in the networking
stack use DEBUG_NET_WARN_ON_ONCE to avoid executing a new branch on
every packet.

Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Link: https://lore.kernel.org/r/20230321150725.127229-2-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: Catch invalid index in XPS mapping

[ Upstream commit 5dd0dfd55baec0742ba8f5625a0dd064aca7db16 ]

When setting the XPS value of a TX queue, warn the user once if the
index of the queue is greater than the number of allocated TX queues.

Previously, this scenario went uncaught. In the best case, it resulted
in unnecessary allocations. In the worst case, it resulted in
out-of-bounds memory references through calls to `netdev_get_tx_queue(
dev, index)`. Therefore, it is important to inform the user but not
worth returning an error and risk downing the netdevice.

Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Link: https://lore.kernel.org/r/20230321150725.127229-1-nnac123@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: pasemi: Fix return type of pasemi_mac_start_tx()

[ Upstream commit c8384d4a51e7cb0e6587f3143f29099f202c5de1 ]

With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
warning in clang aims to catch these at compile time, which reveals:

  drivers/net/ethernet/pasemi/pasemi_mac.c:1665:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
          .ndo_start_xmit         = pasemi_mac_start_tx,
                                    ^~~~~~~~~~~~~~~~~~~
  1 error generated.

->ndo_start_xmit() in 'struct net_device_ops' expects a return type of
'netdev_tx_t', not 'int'. Adjust the return type of
pasemi_mac_start_tx() to match the prototype's to resolve the warning.
While PowerPC does not currently implement support for kCFI, it could in
the future, which means this warning becomes a fatal CFI failure at run
time.

Link: https://github.com/ClangBuiltLinux/linux/issues/1750
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20230319-pasemi-incompatible-pointer-types-strict-v1-1-1b9459d8aef0@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bnxt: avoid overflow in bnxt_get_nvram_directory()

[ Upstream commit 7c6dddc239abe660598c49ec95ea0ed6399a4b2a ]

The value of an arithmetic expression is subject
of possible overflow due to a failure to cast operands to a larger data
type before performing arithmetic. Used macro for multiplication instead
operator for avoiding overflow.

Found by Security Code and Linux Verification
Center (linuxtesting.org) with SVACE.

Signed-off-by: Maxim Korotkov <korotkov.maxim.s@gmail.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/20230309174347.3515-1-korotkov.maxim.s@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: lpfc: Correct used_rpi count when devloss tmo fires with no recovery

[ Upstream commit db651ec22524eb8f9c854fbb4d9acd5d7e5be9e4 ]

A fabric controller can sometimes send an RDP request right before a link
down event.  Because of this outstanding RDP request, the driver does not
remove the last reference count on its ndlp causing a potential leak of RPI
resources when devloss tmo fires.

In lpfc_cmpl_els_rsp(), modify the NPIV clause to always allow the
lpfc_drop_node() routine to execute when not registered with SCSI
transport.

This relaxes the contraint that an NPIV ndlp must be in a specific state in
order to call lpfc_drop node.  Logic is revised such that the
lpfc_drop_node() routine is always called to ensure the last ndlp decrement
occurs.

Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20230301231626.9621-7-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: lpfc: Prevent lpfc_debugfs_lockstat_write() buffer overflow

[ Upstream commit c6087b82a9146826564a55c5ca0164cac40348f5 ]

A static code analysis tool flagged the possibility of buffer overflow when
using copy_from_user() for a debugfs entry.

Currently, it is possible that copy_from_user() copies more bytes than what
would fit in the mybuf char array.  Add a min() restriction check between
sizeof(mybuf) - 1 and nbytes passed from the userspace buffer to protect
against buffer overflow.

Link: https://lore.kernel.org/r/20230301231626.9621-2-justintee8345@gmail.com
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ext2: Check block size validity during mount

[ Upstream commit 62aeb94433fcec80241754b70d0d1836d5926b0a ]

Check that log of block size stored in the superblock has sensible
value. Otherwise the shift computing the block size can overflow leading
to undefined behavior.

Reported-by: syzbot+4fec412f59eba8c01b77@syzkaller.appspotmail.com
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

wifi: brcmfmac: cfg80211: Pass the PMK in binary instead of hex

[ Upstream commit 89b89e52153fda2733562776c7c9d9d3ebf8dd6d ]

Apparently the hex passphrase mechanism does not work on newer
chips/firmware (e.g. BCM4387). It seems there was a simple way of
passing it in binary all along, so use that and avoid the hexification.

OpenBSD has been doing it like this from the beginning, so this should
work on all chips.

Also clear the structure before setting the PMK. This was leaking
uninitialized stack contents to the device.

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230214092423.15175-6-marcan@marcan.st
Signed-off-by: Sasha Levin <sashal@kernel.org>

wifi: brcmfmac: pcie: Provide a buffer of random bytes to the device

[ Upstream commit 91918ce88d9fef408bb12c46a27c73d79b604c20 ]

Newer Apple firmwares on chipsets without a hardware RNG require the
host to provide a buffer of 256 random bytes to the device on
initialization. This buffer is present immediately before NVRAM,
suffixed by a footer containing a magic number and the buffer length.

This won't affect chips/firmwares that do not use this feature, so do it
unconditionally for all Apple platforms (those with an Apple OTP).

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230214080034.3828-3-marcan@marcan.st
Signed-off-by: Sasha Levin <sashal@kernel.org>

bpf: Annotate data races in bpf_local_storage

[ Upstream commit 0a09a2f933c73dc76ab0b72da6855f44342a8903 ]

There are a few cases where hlist_node is checked to be unhashed without
holding the lock protecting its modification. In this case, one must use
hlist_unhashed_lockless to avoid load tearing and KCSAN reports. Fix
this by using lockless variant in places not protected by the lock.

Since this is not prompted by any actual KCSAN reports but only from
code review, I have not included a fixes tag.

Cc: Martin KaFai Lau <martin.lau@kernel.org>
Cc: KP Singh <kpsingh@kernel.org>
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20230221200646.2500777-4-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

wifi: ath: Silence memcpy run-time false positive warning

[ Upstream commit bfcc8ba45eb87bfaaff900bbad2b87b204899d41 ]

The memcpy() in ath_key_config() was attempting to write across
neighboring struct members in struct ath_keyval. Introduce a wrapping
struct_group, kv_values, to be the addressable target of the memcpy
without overflowing an individual member. Silences the false positive
run-time warning:

  memcpy: detected field-spanning write (size 32) of single field "hk.kv_val" at drivers/net/wireless/ath/key.c:506 (size 16)

Link: https://bbs.archlinux.org/viewtopic.php?id=282254
Cc: Kalle Valo <kvalo@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230210054310.never.554-kees@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: mediatek: vcodec: Fix potential array out-of-bounds in decoder queue_setup

[ Upstream commit 8fbcf730cb89c3647f3365226fe7014118fa93c7 ]

variable *nplanes is provided by user via system call argument. The
possible value of q_data->fmt->num_planes is 1-3, while the value
of *nplanes can be 1-8. The array access by index i can cause array
out-of-bounds.

Fix this bug by checking *nplanes against the array size.

Signed-off-by: Wei Chen <harperchen1110@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: Prefer designated initializers over memset for subdev pad ops

[ Upstream commit e3a69496a1cde364c74a600d7a370179b58aed29 ]

Structures passed to subdev pad operations are all zero-initialized, but
not always with the same kind of code constructs. While most drivers
used designated initializers, which zero all the fields that are not
specified, when declaring variables, some use memset(). Those two
methods lead to the same end result, and, depending on compiler
optimizations, may even be completely equivalent, but they're not
consistent.

Improve coding style consistency by using designated initializers
instead of calling memset(). Where applicable, also move the variables
to inner scopes of for loops to ensure correct initialization in all
iterations.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Lad Prabhakar <prabhakar.csengg@gmail.com> # For am437x
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amdgpu: Fix sdma v4 sw fini error

[ Upstream commit 5e08e9c742a00384e5abe74bd40cf4dc15cb3a2e ]

Fix sdma v4 sw fini error for sdma 4.2.2 to
solve the following general protection fault

[  +0.108196] general protection fault, probably for non-canonical
address 0xd5e5a4ae79d24a32: 0000 [#1] PREEMPT SMP PTI
[  +0.000018] RIP: 0010:free_fw_priv+0xd/0x70
[  +0.000022] Call Trace:
[  +0.000012]  <TASK>
[  +0.000011]  release_firmware+0x55/0x80
[  +0.000021]  amdgpu_ucode_release+0x11/0x20 [amdgpu]
[  +0.000415]  amdgpu_sdma_destroy_inst_ctx+0x4f/0x90 [amdgpu]
[  +0.000360]  sdma_v4_0_sw_fini+0xce/0x110 [amdgpu]

Signed-off-by: lyndonli <Lyndon.Li@amd.com>
Reviewed-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd: Fix an out of bounds error in BIOS parser

[ Upstream commit d116db180decec1b21bba31d2ff495ac4d8e1b83 ]

The array is hardcoded to 8 in atomfirmware.h, but firmware provides
a bigger one sometimes. Deferencing the larger array causes an out
of bounds error.

commit 4fc1ba4aa589 ("drm/amd/display: fix array index out of bound error
in bios parser") fixed some of this, but there are two other cases
not covered by it.  Fix those as well.

Reported-by: erhard_f@mailbox.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=214853
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2473
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd/display: Correct DML calculation to follow HW SPEC

[ Upstream commit 385c3e4c29e1d4ce8f68687a8c84621e4c0e0416 ]

[Why]
In 2560x1600@240p eDP panel, driver use lowest voltage level
to play 1080p video cause underflow. According to HW SPEC,
the senario should use high voltage level.

[How]
ChromaPre value is zero when bandwidth validation.
Correct ChromaPre calculation.

Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Paul Hsieh <Paul.Hsieh@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ACPI: video: Remove desktops without backlight DMI quirks

[ Upstream commit abe4f5ae5efa6a63c7d5abfa07eb02bb56b4654e ]

After the recent backlight changes acpi_video# backlight devices are only
registered when explicitly requested from the cmdline, by DMI quirk or by
the GPU driver.

This means that we no longer get false-positive backlight control support
advertised on desktop boards.

Remove the 3 DMI quirks for desktop boards where the false-positive issue
was fixed through quirks before. Note many more desktop boards were
affected but we never build a full quirk list for this.

Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

irqchip/gicv3: Workaround for NVIDIA erratum T241-FABRIC-4

[ Upstream commit 35727af2b15d98a2dd2811d631d3a3886111312e ]

The T241 platform suffers from the T241-FABRIC-4 erratum which causes
unexpected behavior in the GIC when multiple transactions are received
simultaneously from different sources. This hardware issue impacts
NVIDIA server platforms that use more than two T241 chips
interconnected. Each chip has support for 320 {E}SPIs.

This issue occurs when multiple packets from different GICs are
incorrectly interleaved at the target chip. The erratum text below
specifies exactly what can cause multiple transfer packets susceptible
to interleaving and GIC state corruption. GIC state corruption can
lead to a range of problems, including kernel panics, and unexpected
behavior.

>From the erratum text:
  "In some cases, inter-socket AXI4 Stream packets with multiple
  transfers, may be interleaved by the fabric when presented to ARM
  Generic Interrupt Controller. GIC expects all transfers of a packet
  to be delivered without any interleaving.

  The following GICv3 commands may result in multiple transfer packets
  over inter-socket AXI4 Stream interface:
   - Register reads from GICD_I* and GICD_N*
   - Register writes to 64-bit GICD registers other than GICD_IROUTERn*
   - ITS command MOVALL

  Multiple commands in GICv4+ utilize multiple transfer packets,
  including VMOVP, VMOVI, VMAPP, and 64-bit register accesses."

  This issue impacts system configurations with more than 2 sockets,
  that require multi-transfer packets to be sent over inter-socket
  AXI4 Stream interface between GIC instances on different sockets.
  GICv4 cannot be supported. GICv3 SW model can only be supported
  with the workaround. Single and Dual socket configurations are not
  impacted by this issue and support GICv3 and GICv4."

Link: https://developer.nvidia.com/docs/t241-fabric-4/nvidia-t241-fabric-4-errata.pdf
Writing to the chip alias region of the GICD_In{E} registers except
GICD_ICENABLERn has an equivalent effect as writing to the global
distributor. The SPI interrupt deactivate path is not impacted by
the erratum.

To fix this problem, implement a workaround that ensures read accesses
to the GICD_In{E} registers are directed to the chip that owns the
SPI, and disable GICv4.x features. To simplify code changes, the
gic_configure_irq() function uses the same alias region for both read
and write operations to GICD_ICFGR.

Co-developed-by: Vikram Sethi <vsethi@nvidia.com>
Signed-off-by: Vikram Sethi <vsethi@nvidia.com>
Signed-off-by: Shanker Donthineni <sdonthineni@nvidia.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com> (for SMCCC/SOC ID bits)
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230319024314.3540573-2-sdonthineni@nvidia.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: qcom: sdm845-polaris: Drop inexistent properties

[ Upstream commit fbc3a1df2866608ca43e7e6d602f66208a5afd88 ]

Drop the qcom,snoc-host-cap-skip-quirk that was never introduced to
solve schema warnings.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230406-topic-ath10k_bindings-v3-2-00895afc7764@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

ACPICA: ACPICA: check null return of ACPI_ALLOCATE_ZEROED in acpi_db_display_objects

[ Upstream commit ae5a0eccc85fc960834dd66e3befc2728284b86c ]

ACPICA commit 0d5f467d6a0ba852ea3aad68663cbcbd43300fd4

ACPI_ALLOCATE_ZEROED may fails, object_info might be null and will cause
null pointer dereference later.

Link: https://github.com/acpica/acpica/commit/0d5f467d
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ACPICA: Avoid undefined behavior: applying zero offset to null pointer

[ Upstream commit 05bb0167c80b8f93c6a4e0451b7da9b96db990c2 ]

ACPICA commit 770653e3ba67c30a629ca7d12e352d83c2541b1e

Before this change we see the following UBSAN stack trace in Fuchsia:

  #0    0x000021e4213b3302 in acpi_ds_init_aml_walk(struct acpi_walk_state*, union acpi_parse_object*, struct acpi_namespace_node*, u8*, u32, struct acpi_evaluate_info*, u8) ../../third_party/acpica/source/components/dispatcher/dswstate.c:682 <platform-bus-x86.so>+0x233302
  #1.2  0x000020d0f660777f in ubsan_get_stack_trace() compiler-rt/lib/ubsan/ubsan_diag.cpp:41 <libclang_rt.asan.so>+0x3d77f
  #1.1  0x000020d0f660777f in maybe_print_stack_trace() compiler-rt/lib/ubsan/ubsan_diag.cpp:51 <libclang_rt.asan.so>+0x3d77f
  #1    0x000020d0f660777f in ~scoped_report() compiler-rt/lib/ubsan/ubsan_diag.cpp:387 <libclang_rt.asan.so>+0x3d77f
  #2    0x000020d0f660b96d in handlepointer_overflow_impl() compiler-rt/lib/ubsan/ubsan_handlers.cpp:809 <libclang_rt.asan.so>+0x4196d
  #3    0x000020d0f660b50d in compiler-rt/lib/ubsan/ubsan_handlers.cpp:815 <libclang_rt.asan.so>+0x4150d
  #4    0x000021e4213b3302 in acpi_ds_init_aml_walk(struct acpi_walk_state*, union acpi_parse_object*, struct acpi_namespace_node*, u8*, u32, struct acpi_evaluate_info*, u8) ../../third_party/acpica/source/components/dispatcher/dswstate.c:682 <platform-bus-x86.so>+0x233302
  #5    0x000021e4213e2369 in acpi_ds_call_control_method(struct acpi_thread_state*, struct acpi_walk_state*, union acpi_parse_object*) ../../third_party/acpica/source/components/dispatcher/dsmethod.c:605 <platform-bus-x86.so>+0x262369
  #6    0x000021e421437fac in acpi_ps_parse_aml(struct acpi_walk_state*) ../../third_party/acpica/source/components/parser/psparse.c:550 <platform-bus-x86.so>+0x2b7fac
  #7    0x000021e4214464d2 in acpi_ps_execute_method(struct acpi_evaluate_info*) ../../third_party/acpica/source/components/parser/psxface.c:244 <platform-bus-x86.so>+0x2c64d2
  #8    0x000021e4213aa052 in acpi_ns_evaluate(struct acpi_evaluate_info*) ../../third_party/acpica/source/components/namespace/nseval.c:250 <platform-bus-x86.so>+0x22a052
  #9    0x000021e421413dd8 in acpi_ns_init_one_device(acpi_handle, u32, void*, void**) ../../third_party/acpica/source/components/namespace/nsinit.c:735 <platform-bus-x86.so>+0x293dd8
  #10   0x000021e421429e98 in acpi_ns_walk_namespace(acpi_object_type, acpi_handle, u32, u32, acpi_walk_callback, acpi_walk_callback, void*, void**) ../../third_party/acpica/source/components/namespace/nswalk.c:298 <platform-bus-x86.so>+0x2a9e98
  #11   0x000021e4214131ac in acpi_ns_initialize_devices(u32) ../../third_party/acpica/source/components/namespace/nsinit.c:268 <platform-bus-x86.so>+0x2931ac
  #12   0x000021e42147c40d in acpi_initialize_objects(u32) ../../third_party/acpica/source/components/utilities/utxfinit.c:304 <platform-bus-x86.so>+0x2fc40d
  #13   0x000021e42126d603 in acpi::acpi_impl::initialize_acpi(acpi::acpi_impl*) ../../src/devices/board/lib/acpi/acpi-impl.cc:224 <platform-bus-x86.so>+0xed603

Add a simple check that avoids incrementing a pointer by zero, but
otherwise behaves as before. Note that our findings are against ACPICA
20221020, but the same code exists on master.

Link: https://github.com/acpica/acpica/commit/770653e3
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/msm/dp: Clean up handling of DP AUX interrupts

[ Upstream commit b20566cdef05cd40d95f10869d2a7646f48b1bbe ]

The DP AUX interrupt handling was a bit of a mess.
* There were two functions (one for "native" transfers and one for
  "i2c" transfers) that were quite similar. It was hard to say how
  many of the differences between the two functions were on purpose
  and how many of them were just an accident of how they were coded.
* Each function sometimes used "else if" to test for error bits and
  sometimes didn't and again it was hard to say if this was on purpose
  or just an accident.
* The two functions wouldn't notice whether "unknown" bits were
  set. For instance, there seems to be a bit "DP_INTR_PLL_UNLOCKED"
  and if it was set there would be no indication.
* The two functions wouldn't notice if more than one error was set.

Let's fix this by being more consistent / explicit about what we're
doing.

By design this could cause different handling for AUX transfers,
though I'm not actually aware of any bug fixed as a result of
this patch (this patch was created because we simply noticed how odd
the old code was by code inspection). Specific notes here:
1. In the old native transfer case if we got "done + wrong address"
   we'd ignore the "wrong address" (because of the "else if"). Now we
   won't.
2. In the old native transfer case if we got "done + timeout" we'd
   ignore the "timeout" (because of the "else if"). Now we won't.
3. In the old native transfer case we'd see "nack_defer" and translate
   it to the error number for "nack". This differed from the i2c
   transfer case where "nack_defer" was given the error number for
   "nack_defer". This 100% can't matter because the only user of this
   error number treats "nack defer" the same as "nack", so it's clear
   that the difference between the "native" and "i2c" was pointless
   here.
4. In the old i2c transfer case if we got "done" plus any error
   besides "nack" or "defer" then we'd ignore the error. Now we don't.
5. If there is more than one error signaled by the hardware it's
   possible that we'll report a different one than we used to. I don't
   know if this matters. If someone is aware of a case this matters we
   should document it and change the code to make it explicit.
6. One quirk we keep (I don't know if this is important) is that in
   the i2c transfer case if we see "done + defer" we report that as a
   "nack". That seemed too intentional in the old code to just drop.

After this change we will add extra logging, including:
* A warning if we see more than one error bit set.
* A warning if we see an unexpected interrupt.
* A warning if we get an AUX transfer interrupt when shouldn't.

It actually turns out that as a result of this change then at boot we
sometimes see an error:
  [drm:dp_aux_isr] *ERROR* Unexpected DP AUX IRQ 0x01000000 when not busy
That means that, during init, we are seeing DP_INTR_PLL_UNLOCKED. For
now I'm going to say that leaving this error reported in the logs is
OK-ish and hopefully it will encourage someone to track down what's
going on at init time.

One last note here is that this change renames one of the interrupt
bits. The bit named "i2c done" clearly was used for native transfers
being done too, so I renamed it to indicate this.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/520658/
Link: https://lore.kernel.org/r/20230126170745.v2.1.I90ffed3ddd21e818ae534f820cb4d6d8638859ab@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/tegra: Avoid potential 32-bit integer overflow

[ Upstream commit 2429b3c529da29d4277d519bd66d034842dcd70c ]

In tegra_sor_compute_config(), the 32-bit value mode->clock is
multiplied by 1000, and assigned to the u64 variable pclk. We can avoid
a potential 32-bit integer overflow by casting mode->clock to u64 before
we do the arithmetic and assignment.

Signed-off-by: Nur Hussein <hussein@unixcat.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

remoteproc: stm32_rproc: Add mutex protection for workqueue

[ Upstream commit 35bdafda40cc343ad2ba2cce105eba03a70241cc ]

The workqueue may execute late even after remoteproc is stopped or
stopping, some resources (rpmsg device and endpoint) have been
released in rproc_stop_subdevices(), then rproc_vq_interrupt()
accessing these resources will cause kernel dump.

Call trace:
virtqueue_add_inbuf
virtqueue_add_inbuf
rpmsg_recv_single
rpmsg_recv_done
vring_interrupt
stm32_rproc_mb_vq_work
process_one_work
worker_thread
kthread

Suggested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Link: https://lore.kernel.org/r/20230331160634.3113031-1-arnaud.pouliquen@foss.st.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd/display: fixed dcn30+ underflow issue

[ Upstream commit 37403ced9f2873fab7f39ab4ac963bbb33fb0bc0 ]

[Why]
Observing underflow on dcn30+ system config at 4k144hz

[How]
We set the UCLK hardmax on AC/DC switch if softmax is enabled
and also on boot. While booting up the UCLK Hardmax is set
to softmax before the init sequence and the init sequence
resets the hardmax to UCLK max which enables P-state switching.
Just added a conditional check to avoid setting hardmax on init.

Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Ayush Gupta <ayugupta@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ACPI: EC: Fix oops when removing custom query handlers

[ Upstream commit e5b492c6bb900fcf9722e05f4a10924410e170c1 ]

When removing custom query handlers, the handler might still
be used inside the EC query workqueue, causing a kernel oops
if the module holding the callback function was already unloaded.

Fix this by flushing the EC query workqueue when removing
custom query handlers.

Tested on a Acer Travelmate 4002WLMi

Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

firmware: arm_sdei: Fix sleep from invalid context BUG

[ Upstream commit d2c48b2387eb89e0bf2a2e06e30987cf410acad4 ]

Running a preempt-rt (v6.2-rc3-rt1) based kernel on an Ampere Altra
triggers:

  BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:46
  in_atomic(): 0, irqs_disabled(): 128, non_block: 0, pid: 24, name: cpuhp/0
  preempt_count: 0, expected: 0
  RCU nest depth: 0, expected: 0
  3 locks held by cpuhp/0/24:
    #0: ffffda30217c70d0 (cpu_hotplug_lock){++++}-{0:0}, at: cpuhp_thread_fun+0x5c/0x248
    #1: ffffda30217c7120 (cpuhp_state-up){+.+.}-{0:0}, at: cpuhp_thread_fun+0x5c/0x248
    #2: ffffda3021c711f0 (sdei_list_lock){....}-{3:3}, at: sdei_cpuhp_up+0x3c/0x130
  irq event stamp: 36
  hardirqs last  enabled at (35): [<ffffda301e85b7bc>] finish_task_switch+0xb4/0x2b0
  hardirqs last disabled at (36): [<ffffda301e812fec>] cpuhp_thread_fun+0x21c/0x248
  softirqs last  enabled at (0): [<ffffda301e80b184>] copy_process+0x63c/0x1ac0
  softirqs last disabled at (0): [<0000000000000000>] 0x0
  CPU: 0 PID: 24 Comm: cpuhp/0 Not tainted 5.19.0-rc3-rt5-[...]
  Hardware name: WIWYNN Mt.Jade Server [...]
  Call trace:
    dump_backtrace+0x114/0x120
    show_stack+0x20/0x70
    dump_stack_lvl+0x9c/0xd8
    dump_stack+0x18/0x34
    __might_resched+0x188/0x228
    rt_spin_lock+0x70/0x120
    sdei_cpuhp_up+0x3c/0x130
    cpuhp_invoke_callback+0x250/0xf08
    cpuhp_thread_fun+0x120/0x248
    smpboot_thread_fn+0x280/0x320
    kthread+0x130/0x140
    ret_from_fork+0x10/0x20

sdei_cpuhp_up() is called in the STARTING hotplug section,
which runs with interrupts disabled. Use a CPUHP_AP_ONLINE_DYN entry
instead to execute the cpuhp cb later, with preemption enabled.

SDEI originally got its own cpuhp slot to allow interacting
with perf. It got superseded by pNMI and this early slot is not
relevant anymore. [1]

Some SDEI calls (e.g. SDEI_1_0_FN_SDEI_PE_MASK) take actions on the
calling CPU. It is checked that preemption is disabled for them.
_ONLINE cpuhp cb are executed in the 'per CPU hotplug thread'.
Preemption is enabled in those threads, but their cpumask is limited
to 1 CPU.
Move 'WARN_ON_ONCE(preemptible())' statements so that SDEI cpuhp cb
don't trigger them.

Also add a check for the SDEI_1_0_FN_SDEI_PRIVATE_RESET SDEI call
which acts on the calling CPU.

[1]:
https://lore.kernel.org/all/5813b8c5-ae3e-87fd-fccc-94c9cd08816d@arm.com/

Suggested-by: James Morse <james.morse@arm.com>
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Reviewed-by: James Morse <james.morse@arm.com>
Link: https://lore.kernel.org/r/20230216084920.144064-1-pierre.gondois@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: imx8mq-librem5: Remove dis_u3_susphy_quirk from usb_dwc3_0

[ Upstream commit cfe9de291bd2bbce18c5cd79e1dd582cbbacdb4f ]

This reduces power consumption in system suspend by about 10%.

Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

memstick: r592: Fix UAF bug in r592_remove due to race condition

[ Upstream commit 63264422785021704c39b38f65a78ab9e4a186d7 ]

In r592_probe, dev->detect_timer was bound with r592_detect_timer.
In r592_irq function, the timer function will be invoked by mod_timer.

If we remove the module which will call hantro_release to make cleanup,
there may be a unfinished work. The possible sequence is as follows,
which will cause a typical UAF bug.

Fix it by canceling the work before cleanup in r592_remove.

CPU0                  CPU1

                    |r592_detect_timer
r592_remove         |
  memstick_free_host|
  put_device;       |
  kfree(host);      |
                    |
                    | queue_work
                    |   &host->media_checker //use

Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Link: https://lore.kernel.org/r/20230307164338.1246287-1-zyytlz.wz@163.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/rockchip: dw_hdmi: cleanup drm encoder during unbind

[ Upstream commit b5af48eedcb53491c02ded55d5991e03d6da6dbf ]

This fixes a use-after-free crash during rmmod.

The DRM encoder is embedded inside the larger rockchip_hdmi,
which is allocated with the component. The component memory
gets freed before the main drm device is destroyed. Fix it
by running encoder cleanup before tearing down its container.

Signed-off-by: Toby Chen <tobyc@nvidia.com>
[moved encoder cleanup above clk_disable, similar to bind-error-path]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230317005126.496-1-tobyc@nvidia.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

ACPI: processor: Check for null return of devm_kzalloc() in fch_misc_setup()

[ Upstream commit 4dea41775d951ff1f7b472a346a8ca3ae7e74455 ]

devm_kzalloc() may fail, clk_data->name might be NULL and will
cause a NULL pointer dereference later.

Signed-off-by: Kang Chen <void0red@gmail.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: pvrusb2: VIDEO_PVRUSB2 depends on DVB_CORE to use dvb_* symbols

[ Upstream commit 1107283b3351bef138cd12dbda1f999891cab7db ]

A rand config causes this link error
vmlinux.o: In function `pvr2_dvb_create':
(.text+0x8af1d2): undefined reference to `dvb_register_adapter'

The rand config has
CONFIG_VIDEO_PVRUSB2=y
CONFIG_VIDEO_DEV=y
CONFIG_DVB_CORE=m

VIDEO_PVRUSB2 should also depend on DVB_CORE.

Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: pci: tw68: Fix null-ptr-deref bug in buf prepare and finish

[ Upstream commit 1634b7adcc5bef645b3666fdd564e5952a9e24e0 ]

When the driver calls tw68_risc_buffer() to prepare the buffer, the
function call dma_alloc_coherent may fail, resulting in a empty buffer
buf->cpu. Later when we free the buffer or access the buffer, null ptr
deref is triggered.

This bug is similar to the following one:
https://git.linuxtv.org/media_stage.git/commit/?id=2b064d91440b33fba5b452f2d1b31f13ae911d71.

We believe the bug can be also dynamically triggered from user side.
Similarly, we fix this by checking the return value of tw68_risc_buffer()
and the value of buf->cpu before buffer free.

Signed-off-by: harperchen <harperchen1110@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: cx23885: Fix a null-ptr-deref bug in buffer_prepare() and buffer_finish()

[ Upstream commit 47e8b73bc35d7c54642f78e498697692f6358996 ]

When the driver calls cx23885_risc_buffer() to prepare the buffer, the
function call dma_alloc_coherent may fail, resulting in a empty buffer
risc->cpu. Later when we free the buffer or access the buffer, null ptr
deref is triggered.

This bug is similar to the following one:
https://git.linuxtv.org/media_stage.git/commit/?id=2b064d91440b33fba5b452f2d1b31f13ae911d71.

We believe the bug can be also dynamically triggered from user side.
Similarly, we fix this by checking the return value of cx23885_risc_buffer()
and the value of risc->cpu before buffer free.

Signed-off-by: harperchen <harperchen1110@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: qcom: msm8996: Add missing DWC3 quirks

[ Upstream commit d0af0537e28f6eace02deed63b585396de939213 ]

Add missing dwc3 quirks from msm-3.18. Unfortunately, none of them
make `dwc3-qcom 6af8800.usb: HS-PHY not in L2` go away.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230302011849.1873056-1-konrad.dybcio@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

remoteproc: imx_dsp_rproc: Add custom memory copy implementation for i.MX DSP Cores

[ Upstream commit 408ec1ff0caa340c57eecf4cbd14ef0132036a50 ]

The IRAM is part of the HiFi DSP.
According to hardware specification only 32-bits write are allowed
otherwise we get a Kernel panic.

Therefore add a custom memory copy and memset functions to deal with
the above restriction.

Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Link: https://lore.kernel.org/r/20230221170356.27923-1-iuliana.prodan@oss.nxp.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

regmap: cache: Return error in cache sync operations for REGCACHE_NONE

[ Upstream commit fd883d79e4dcd2417c2b80756f22a2ff03b0f6e0 ]

There is no sense in doing a cache sync on REGCACHE_NONE regmaps.
Instead of panicking the kernel due to missing cache_ops, return an error
to client driver.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20230313071812.13577-1-alexander.stein@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd/display: Use DC_LOG_DC in the trasform pixel function

[ Upstream commit 7222f5841ff49709ca666b05ff336776e0664a20 ]

[Why & How]
DC now uses a new commit sequence which is more robust since it
addresses cases where we need to reorganize pipes based on planes and
other parameters. As a result, this new commit sequence reset the DC
state by cleaning plane states and re-creating them accordingly with the
need. For this reason, the dce_transform_set_pixel_storage_depth can be
invoked after a plane state is destroyed and before its re-creation. In
this situation and on DCE devices, DC will hit a condition that will
trigger a dmesg log that looks like this:

Console: switching to colour frame buffer device 240x67
------------[ cut here ]------------
[..]
Hardware name: System manufacturer System Product Name/PRIME X370-PRO, BIOS 5603 07/28/2020
RIP: 0010:dce_transform_set_pixel_storage_depth+0x3f8/0x480 [amdgpu]
[..]
RSP: 0018:ffffc9000202b850 EFLAGS: 00010293
RAX: ffffffffa081d100 RBX: ffff888110790000 RCX: 000000000000000c
RDX: ffff888100bedbf8 RSI: 0000000000001a50 RDI: ffff88810463c900
RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000007
R10: 0000000000000001 R11: 0000000000000f00 R12: ffff88810f500010
R13: ffff888100bedbf8 R14: ffff88810f515688 R15: 0000000000000000
FS:  00007ff0159249c0(0000) GS:ffff88840e940000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007ff01528e550 CR3: 0000000002a10000 CR4: 00000000003506e0
Call Trace:
 <TASK>
 ? dm_write_reg_func+0x21/0x80 [amdgpu 340dadd3f7c8cf4be11cf0bdc850245e99abe0e8]
 dc_stream_set_dither_option+0xfb/0x130 [amdgpu 340dadd3f7c8cf4be11cf0bdc850245e99abe0e8]
 amdgpu_dm_crtc_configure_crc_source+0x10b/0x190 [amdgpu 340dadd3f7c8cf4be11cf0bdc850245e99abe0e8]
 amdgpu_dm_atomic_commit_tail+0x20a8/0x2a90 [amdgpu 340dadd3f7c8cf4be11cf0bdc850245e99abe0e8]
 ? free_unref_page_commit+0x98/0x170
 ? free_unref_page+0xcc/0x150
 commit_tail+0x94/0x120
 drm_atomic_helper_commit+0x10f/0x140
 drm_atomic_commit+0x94/0xc0
 ? drm_plane_get_damage_clips.cold+0x1c/0x1c
 drm_client_modeset_commit_atomic+0x203/0x250
 drm_client_modeset_commit_locked+0x56/0x150
 drm_client_modeset_commit+0x21/0x40
 drm_fb_helper_lastclose+0x42/0x70
 amdgpu_driver_lastclose_kms+0xa/0x10 [amdgpu 340dadd3f7c8cf4be11cf0bdc850245e99abe0e8]
 drm_release+0xda/0x110
 __fput+0x89/0x240
 task_work_run+0x5c/0x90
 do_exit+0x333/0xae0
 do_group_exit+0x2d/0x90
 __x64_sys_exit_group+0x14/0x20
 do_syscall_64+0x5b/0x80
 ? exit_to_user_mode_prepare+0x1e/0x140
 entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7ff016ceaca1
Code: Unable to access opcode bytes at RIP 0x7ff016ceac77.
RSP: 002b:00007ffe7a2357e8 EFLAGS: 00000246 ORIG_RAX: 00000000000000e7
RAX: ffffffffffffffda RBX: 00007ff016e15a00 RCX: 00007ff016ceaca1
RDX: 000000000000003c RSI: 00000000000000e7 RDI: 0000000000000000
RBP: 0000000000000000 R08: ffffffffffffff78 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007ff016e15a00
R13: 0000000000000000 R14: 00007ff016e1aee8 R15: 00007ff016e1af00
 </TASK>

Since this issue only happens in a transition state on DC, this commit
replace BREAK_TO_DEBUGGER with DC_LOG_DC.

Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd/display: Enable HostVM based on rIOMMU active

[ Upstream commit 97fa4dfa66fdd52ad3d0c9fadeaaa1e87605bac7 ]

[Why]
There is underflow and flickering occuring. The
underflow stops when hostvm is forced to active.
According to policy, hostvm should be enabled if riommu
is active, but this is not taken into account when
deciding whether to enable hostvm.

[What]
For DCN314, set hostvm to true if riommu is active.

Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Gabe Teeger <gabe.teeger@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

platform/x86: x86-android-tablets: Add Acer Iconia One 7 B1-750 data

[ Upstream commit 2f0cf1e85ddb5ae17284050dc1adafb89e4f1d8f ]

The Acer Iconia One 7 B1-750 is a x86 ACPI tablet which ships with Android
x86 as factory OS. Its DSDT contains a bunch of I2C devices which are not
actually there, causing various resource conflicts. Enumeration of these
is skipped through the acpi_quirk_skip_i2c_client_enumeration().

Add support for manually instantiating the I2C + other devices which are
actually present on this tablet by adding the necessary device info to
the x86-android-tablets module.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230301092331.7038-2-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd/display: Correct DML calculation to align HW formula

[ Upstream commit 26a9f53198c955b15161da48cdb51041a38d5325 ]

[Why]
In 2560x1440@240p eDP panel, some use cases will enable MPC
combine with RGB MPO then underflow happened. This case is
not allowed from HW formula. 

[How]
Correct eDP, DP and DP2 output bpp calculation to align HW
formula.

Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Paul Hsieh <Paul.Hsieh@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd/display: populate subvp cmd info only for the top pipe

[ Upstream commit 9bb10b7aaec3b6278f9cc410c17dcaa129bbbbf0 ]

[Why]
System restart observed while changing the display resolution
to 8k with extended mode. Sytem restart was caused by a page fault.

[How]
When the driver populates subvp info it did it for both the pipes using
vblank which caused an outof bounds array access causing the page fault.
added checks to allow the top pipe only to fix this issue.

Co-authored-by: Ayush Gupta <ayush.gupta@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Ayush Gupta <ayush.gupta@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/displayid: add displayid_get_header() and check bounds better

[ Upstream commit 5bacecc3c56131c31f18b23d366f2184328fd9cf ]

Add a helper to get a pointer to struct displayid_header. To be
pedantic, add buffer overflow checks to not touch the base if that
itself would overflow.

Cc: Iaroslav Boliukin <iam@lach.pw>
Cc: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Reviewed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/4a03b3a5132642d3cdb6d4c2641422955a917292.1676580180.git.jani.nikula@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

fs: hfsplus: remove WARN_ON() from hfsplus_cat_{read,write}_inode()

[ Upstream commit 81b21c0f0138ff5a499eafc3eb0578ad2a99622c ]

syzbot is hitting WARN_ON() in hfsplus_cat_{read,write}_inode(), for
crafted filesystem image can contain bogus length. There conditions are
not kernel bugs that can justify kernel to panic.

Reported-by: syzbot <syzbot+e2787430e752a92b8750@syzkaller.appspotmail.com>
Link: https://syzkaller.appspot.com/bug?extid=e2787430e752a92b8750
Reported-by: syzbot <syzbot+4913dca2ea6e4d43f3f1@syzkaller.appspotmail.com>
Link: https://syzkaller.appspot.com/bug?extid=4913dca2ea6e4d43f3f1
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reviewed-by: Viacheslav Dubeyko <slava@dubeyko.com>
Message-Id: <15308173-5252-d6a3-ae3b-e96d46cb6f41@I-love.SAKURA.ne.jp>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

open: return EINVAL for O_DIRECTORY | O_CREAT

[ Upstream commit 43b450632676fb60e9faeddff285d9fac94a4f58 ]

After a couple of years and multiple LTS releases we received a report
that the behavior of O_DIRECTORY | O_CREAT changed starting with v5.7.

On kernels prior to v5.7 combinations of O_DIRECTORY, O_CREAT, O_EXCL
had the following semantics:

(1) open("/tmp/d", O_DIRECTORY | O_CREAT)
    * d doesn't exist:                create regular file
    * d exists and is a regular file: ENOTDIR
    * d exists and is a directory:    EISDIR

(2) open("/tmp/d", O_DIRECTORY | O_CREAT | O_EXCL)
    * d doesn't exist:                create regular file
    * d exists and is a regular file: EEXIST
    * d exists and is a directory:    EEXIST

(3) open("/tmp/d", O_DIRECTORY | O_EXCL)
    * d doesn't exist:                ENOENT
    * d exists and is a regular file: ENOTDIR
    * d exists and is a directory:    open directory

On kernels since to v5.7 combinations of O_DIRECTORY, O_CREAT, O_EXCL
have the following semantics:

(1) open("/tmp/d", O_DIRECTORY | O_CREAT)
    * d doesn't exist:                ENOTDIR (create regular file)
    * d exists and is a regular file: ENOTDIR
    * d exists and is a directory:    EISDIR

(2) open("/tmp/d", O_DIRECTORY | O_CREAT | O_EXCL)
    * d doesn't exist:                ENOTDIR (create regular file)
    * d exists and is a regular file: EEXIST
    * d exists and is a directory:    EEXIST

(3) open("/tmp/d", O_DIRECTORY | O_EXCL)
    * d doesn't exist:                ENOENT
    * d exists and is a regular file: ENOTDIR
    * d exists and is a directory:    open directory

This is a fairly substantial semantic change that userspace didn't
notice until Pedro took the time to deliberately figure out corner
cases. Since no one noticed this breakage we can somewhat safely assume
that O_DIRECTORY | O_CREAT combinations are likely unused.

The v5.7 breakage is especially weird because while ENOTDIR is returned
indicating failure a regular file is actually created. This doesn't make
a lot of sense.

Time was spent finding potential users of this combination. Searching on
codesearch.debian.net showed that codebases often express semantical
expectations about O_DIRECTORY | O_CREAT which are completely contrary
to what our code has done and currently does.

The expectation often is that this particular combination would create
and open a directory. This suggests users who tried to use that
combination would stumble upon the counterintuitive behavior no matter
if pre-v5.7 or post v5.7 and quickly realize neither semantics give them
what they want. For some examples see the code examples in [1] to [3]
and the discussion in [4].

There are various ways to address this issue. The lazy/simple option
would be to restore the pre-v5.7 behavior and to just live with that bug
forever. But since there's a real chance that the O_DIRECTORY | O_CREAT
quirk isn't relied upon we should try to get away with murder(ing bad
semantics) first. If we need to Frankenstein pre-v5.7 behavior later so
be it.

So let's simply return EINVAL categorically for O_DIRECTORY | O_CREAT
combinations. In addition to cleaning up the old bug this also opens up
the possiblity to make that flag combination do something more intuitive
in the future.

Starting with this commit the following semantics apply:

(1) open("/tmp/d", O_DIRECTORY | O_CREAT)
    * d doesn't exist:                EINVAL
    * d exists and is a regular file: EINVAL
    * d exists and is a directory:    EINVAL

(2) open("/tmp/d", O_DIRECTORY | O_CREAT | O_EXCL)
    * d doesn't exist:                EINVAL
    * d exists and is a regular file: EINVAL
    * d exists and is a directory:    EINVAL

(3) open("/tmp/d", O_DIRECTORY | O_EXCL)
    * d doesn't exist:                ENOENT
    * d exists and is a regular file: ENOTDIR
    * d exists and is a directory:    open directory

One additional note, O_TMPFILE is implemented as:

    #define __O_TMPFILE    020000000
    #define O_TMPFILE      (__O_TMPFILE | O_DIRECTORY)
    #define O_TMPFILE_MASK (__O_TMPFILE | O_DIRECTORY | O_CREAT)

For older kernels it was important to return an explicit error when
O_TMPFILE wasn't supported. So O_TMPFILE requires that O_DIRECTORY is
raised alongside __O_TMPFILE. It also enforced that O_CREAT wasn't
specified. Since O_DIRECTORY | O_CREAT could be used to create a regular
allowing that combination together with __O_TMPFILE would've meant that
false positives were possible, i.e., that a regular file was created
instead of a O_TMPFILE. This could've been used to trick userspace into
thinking it operated on a O_TMPFILE when it wasn't.

Now that we block O_DIRECTORY | O_CREAT completely the check for O_CREAT
in the __O_TMPFILE branch via if ((flags & O_TMPFILE_MASK) != O_TMPFILE)
can be dropped. Instead we can simply check verify that O_DIRECTORY is
raised via if (!(flags & O_DIRECTORY)) and explain this in two comments.

As Aleksa pointed out O_PATH is unaffected by this change since it
always returned EINVAL if O_CREAT was specified - with or without
O_DIRECTORY.

Link: https://lore.kernel.org/lkml/20230320071442.172228-1-pedro.falcato@gmail.com
Link: https://sources.debian.org/src/flatpak/1.14.4-1/subprojects/libglnx/glnx-dirfd.c/?hl=324#L324
Link: https://sources.debian.org/src/flatpak-builder/1.2.3-1/subprojects/libglnx/glnx-shutil.c/?hl=251#L251
Link: https://sources.debian.org/src/ostree/2022.7-2/libglnx/glnx-dirfd.c/?hl=324#L324
Link: https://www.openwall.com/lists/oss-security/2014/11/26/14
Reported-by: Pedro Falcato <pedro.falcato@gmail.com>
Cc: Aleksa Sarai <cyphar@cyphar.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

rcu: Protect rcu_print_task_exp_stall() ->exp_tasks access

[ Upstream commit 3c1566bca3f8349f12b75d0a2d5e4a20ad6262ec ]

For kernels built with CONFIG_PREEMPT_RCU=y, the following scenario can
result in a NULL-pointer dereference:

           CPU1                                           CPU2
rcu_preempt_deferred_qs_irqrestore                rcu_print_task_exp_stall
  if (special.b.blocked)                            READ_ONCE(rnp->exp_tasks) != NULL
    raw_spin_lock_rcu_node
    np = rcu_next_node_entry(t, rnp)
    if (&t->rcu_node_entry == rnp->exp_tasks)
      WRITE_ONCE(rnp->exp_tasks, np)
      ....
      raw_spin_unlock_irqrestore_rcu_node
                                                    raw_spin_lock_irqsave_rcu_node
                                                    t = list_entry(rnp->exp_tasks->prev,
                                                        struct task_struct, rcu_node_entry)
                                                    (if rnp->exp_tasks is NULL, this
                                                       will dereference a NULL pointer)

The problem is that CPU2 accesses the rcu_node structure's->exp_tasks
field without holding the rcu_node structure's ->lock and CPU2 did
not observe CPU1's change to rcu_node structure's ->exp_tasks in time.
Therefore, if CPU1 sets rcu_node structure's->exp_tasks pointer to NULL,
then CPU2 might dereference that NULL pointer.

This commit therefore holds the rcu_node structure's ->lock while
accessing that structure's->exp_tasks field.

[ paulmck: Apply Frederic Weisbecker feedback. ]

Acked-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Zqiang <qiang1.zhang@intel.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests: cgroup: Add 'malloc' failures checks in test_memcontrol

[ Upstream commit c83f320e55a49abd90629f42a72897afd579e0de ]

There are several 'malloc' calls in test_memcontrol, which can be
unsuccessful. This patch will add 'malloc' failures checking to
give more details about test's fail reasons and avoid possible
undefined behavior during the future null dereference (like the
one in alloc_anon_50M_check_swap function).

Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Reviewed-by: Muchun Song <songmuchun@bytedance.com>
Acked-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Roman Gushchin <roman.gushchin@linux.dev>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

refscale: Move shutdown from wait_event() to wait_event_idle()

[ Upstream commit 6bc6e6b27524304aadb9c04611ddb1c84dd7617a ]

The ref_scale_shutdown() kthread/function uses wait_event() to wait for
the refscale test to complete.  However, although the read-side tests
are normally extremely fast, there is no law against specifying a very
large value for the refscale.loops module parameter or against having
a slow read-side primitive.  Either way, this might well trigger the
hung-task timeout.

This commit therefore replaces those wait_event() calls with calls to
wait_event_idle(), which do not trigger the hung-task timeout.

Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ext4: allow ext4_get_group_info() to fail

[ Upstream commit 5354b2af34064a4579be8bc0e2f15a7b70f14b5f ]

Previously, ext4_get_group_info() would treat an invalid group number
as BUG(), since in theory it should never happen.  However, if a
malicious attaker (or fuzzer) modifies the superblock via the block
device while it is the file system is mounted, it is possible for
s_first_data_block to get set to a very large number.  In that case,
when calculating the block group of some block number (such as the
starting block of a preallocation region), could result in an
underflow and very large block group number.  Then the BUG_ON check in
ext4_get_group_info() would fire, resutling in a denial of service
attack that can be triggered by root or someone with write access to
the block device.

For a quality of implementation perspective, it's best that even if
the system administrator does something that they shouldn't, that it
will not trigger a BUG.  So instead of BUG'ing, ext4_get_group_info()
will call ext4_error and return NULL.  We also add fallback code in
all of the callers of ext4_get_group_info() that it might NULL.

Also, since ext4_get_group_info() was already borderline to be an
inline function, un-inline it.  The results in a next reduction of the
compiled text size of ext4 by roughly 2k.

Cc: stable@kernel.org
Link: https://lore.kernel.org/r/20230430154311.579720-2-tytso@mit.edu
Reported-by: syzbot+e2efa3efc15a1c9e95c3@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?id=69b28112e098b070f639efb356393af3ffec4220
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ext4: allow to find by goal if EXT4_MB_HINT_GOAL_ONLY is set

[ Upstream commit 01e4ca29451760b9ac10b4cdc231c52150842643 ]

If EXT4_MB_HINT_GOAL_ONLY is set, ext4_mb_regular_allocator will only
allocate blocks from ext4_mb_find_by_goal. Allow to find by goal in
ext4_mb_find_by_goal if EXT4_MB_HINT_GOAL_ONLY is set or allocation
with EXT4_MB_HINT_GOAL_ONLY set will always fail.

EXT4_MB_HINT_GOAL_ONLY is not used at all, so the problem is not
found for now.

Signed-off-by: Kemeng Shi <shikemeng@huaweicloud.com>
Reviewed-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Link: https://lore.kernel.org/r/20230303172120.3800725-3-shikemeng@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Stable-dep-of: 5354b2af3406 ("ext4: allow ext4_get_group_info() to fail")
Signed-off-by: Sasha Levin <sashal@kernel.org>

ext4: don't clear SB_RDONLY when remounting r/w until quota is re-enabled

[ Upstream commit a44be64bbecb15a452496f60db6eacfee2b59c79 ]

When a file system currently mounted read/only is remounted
read/write, if we clear the SB_RDONLY flag too early, before the quota
is initialized, and there is another process/thread constantly
attempting to create a directory, it's possible to trigger the

WARN_ON_ONCE(dquot_initialize_needed(inode));

in ext4_xattr_block_set(), with the following stack trace:

   WARNING: CPU: 0 PID: 5338 at fs/ext4/xattr.c:2141 ext4_xattr_block_set+0x2ef2/0x3680
   RIP: 0010:ext4_xattr_block_set+0x2ef2/0x3680 fs/ext4/xattr.c:2141
   Call Trace:
    ext4_xattr_set_handle+0xcd4/0x15c0 fs/ext4/xattr.c:2458
    ext4_initxattrs+0xa3/0x110 fs/ext4/xattr_security.c:44
    security_inode_init_security+0x2df/0x3f0 security/security.c:1147
    __ext4_new_inode+0x347e/0x43d0 fs/ext4/ialloc.c:1324
    ext4_mkdir+0x425/0xce0 fs/ext4/namei.c:2992
    vfs_mkdir+0x29d/0x450 fs/namei.c:4038
    do_mkdirat+0x264/0x520 fs/namei.c:4061
    __do_sys_mkdirat fs/namei.c:4076 [inline]
    __se_sys_mkdirat fs/namei.c:4074 [inline]
    __x64_sys_mkdirat+0x89/0xa0 fs/namei.c:4074

Cc: stable@kernel.org
Link: https://lore.kernel.org/r/20230506142419.984260-1-tytso@mit.edu
Reported-by: syzbot+6385d7d3065524c5ca6d@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?id=6513f6cb5cd6b5fc9f37e3bb70d273b94be9c34c
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ext4: reflect error codes from ext4_multi_mount_protect() to its callers

[ Upstream commit 3b50d5018ed06a647bb26c44bb5ae74e59c903c7 ]

This will allow more fine-grained errno codes to be returned by the
mount system call.

Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Stable-dep-of: a44be64bbecb ("ext4: don't clear SB_RDONLY when remounting r/w until quota is re-enabled")
Signed-off-by: Sasha Levin <sashal@kernel.org>

fbdev: arcfb: Fix error handling in arcfb_probe()

[ Upstream commit 5a6bef734247c7a8c19511664ff77634ab86f45b ]

Smatch complains that:
arcfb_probe() warn: 'irq' from request_irq() not released on lines: 587.

Fix error handling in the arcfb_probe() function. If IO addresses are
not provided or framebuffer registration fails, the code will jump to
the err_addr or err_register_fb label to release resources.
If IRQ request fails, previously allocated resources will be freed.

Fixes: 1154ea7dcd8e ("[PATCH] Framebuffer driver for Arc LCD board")
Signed-off-by: Zongjie Li <u202112089@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/i915: taint kernel when force probing unsupported devices

[ Upstream commit 79c901c93562bdf1c84ce6c1b744fbbe4389a6eb ]

For development and testing purposes, the i915.force_probe module
parameter and DRM_I915_FORCE_PROBE kconfig option allow probing of
devices that aren't supported by the driver.

The i915.force_probe module parameter is "unsafe" and setting it taints
the kernel. However, using the kconfig option does not.

Always taint the kernel when force probing a device that is not
supported.

v2: Drop "depends on EXPERT" to avoid build breakage (kernel test robot)

Fixes: 7ef5ef5cdead ("drm/i915: add force_probe module parameter to replace alpha_support")
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Dave Airlie <airlied@gmail.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230504103508.1818540-1-jani.nikula@intel.com
(cherry picked from commit 3312bb4ad09ca6423bd4a5b15a94588a8962fb8e)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/i915: Expand force_probe to block probe of devices as well.

[ Upstream commit 157821fb3e9aaa07cf408686b08d117bf27b7de1 ]

There are new cases where we want to block i915 probe, such
as when experimenting or developing the new Xe driver.

But also, with the new hybrid cards, users or developers might
want to use i915 only on integrated and fully block the probe
of the i915 for the discrete. Or vice versa.

There are even older development and validation reasons,
like when you use some distro where the modprobe.blacklist is
not present.

But in any case, let's introduce a more granular control, but without
introducing yet another parameter, but using the existent force_probe
one.

Just by adding a ! in the begin of the id in the force_probe, like
in this case where we would block the probe for Alder Lake:

$ insmod i915.ko force_probe='!46a6'

v2: Take care of '*' and  '!*' cases as pointed out by
    Gustavo and Jani.

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230103194701.1492984-1-rodrigo.vivi@intel.com
Stable-dep-of: 79c901c93562 ("drm/i915: taint kernel when force probing unsupported devices")
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/i915/dp: prevent potential div-by-zero

[ Upstream commit 0ff80028e2702c7c3d78b69705dc47c1ccba8c39 ]

drm_dp_dsc_sink_max_slice_count() may return 0 if something goes
wrong on the part of the DSC sink and its DPCD register. This null
value may be later used as a divisor in intel_dsc_compute_params(),
which will lead to an error.
In the unlikely event that this issue occurs, fix it by testing the
return value of drm_dp_dsc_sink_max_slice_count() against zero.

Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.

Fixes: a4a157777c80 ("drm/i915/dp: Compute DSC pipe config in atomic check")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230418140430.69902-1-n.zhandarovich@fintech.ru
(cherry picked from commit 51f7008239de011370c5067bbba07f0207f06b72)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/i915: Fix NULL ptr deref by checking new_crtc_state

[ Upstream commit a41d985902c153c31c616fe183cf2ee331e95ecb ]

intel_atomic_get_new_crtc_state can return NULL, unless crtc state wasn't
obtained previously with intel_atomic_get_crtc_state, so we must check it
for NULLness here, just as in many other places, where we can't guarantee
that intel_atomic_get_crtc_state was called.
We are currently getting NULL ptr deref because of that, so this fix was
confirmed to help.

Fixes: 74a75dc90869 ("drm/i915/display: move plane prepare/cleanup to intel_atomic_plane.c")
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230505082212.27089-1-stanislav.lisovskiy@intel.com
(cherry picked from commit 1d5b09f8daf859247a1ea65b0d732a24d88980d8)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/i915/guc: Don't capture Gen8 regs on Xe devices

[ Upstream commit 275dac1f7f5e9c2a2e806b34d3b10804eec0ac3c ]

A pair of pre-Xe registers were being included in the Xe capture list.
GuC was rejecting those as being invalid and logging errors about
them. So, stop doing it.

Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Alan Previn <alan.previn.teres.alexis@intel.com>
Fixes: dce2bd542337 ("drm/i915/guc: Add Gen9 registers for GuC error state capture.")
Cc: Alan Previn <alan.previn.teres.alexis@intel.com>
Cc: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Balasubramani Vivekanandan <balasubramani.vivekanandan@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428185636.457407-2-John.C.Harrison@Intel.com
(cherry picked from commit b049132d61336f643d8faf2f6574b063667088cf)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

af_unix: Fix data races around sk->sk_shutdown.

[ Upstream commit e1d09c2c2f5793474556b60f83900e088d0d366d ]

KCSAN found a data race around sk->sk_shutdown where unix_release_sock()
and unix_shutdown() update it under unix_state_lock(), OTOH unix_poll()
and unix_dgram_poll() read it locklessly.

We need to annotate the writes and reads with WRITE_ONCE() and READ_ONCE().

BUG: KCSAN: data-race in unix_poll / unix_release_sock

write to 0xffff88800d0f8aec of 1 bytes by task 264 on cpu 0:
 unix_release_sock+0x75c/0x910 net/unix/af_unix.c:631
 unix_release+0x59/0x80 net/unix/af_unix.c:1042
 __sock_release+0x7d/0x170 net/socket.c:653
 sock_close+0x19/0x30 net/socket.c:1397
 __fput+0x179/0x5e0 fs/file_table.c:321
 ____fput+0x15/0x20 fs/file_table.c:349
 task_work_run+0x116/0x1a0 kernel/task_work.c:179
 resume_user_mode_work include/linux/resume_user_mode.h:49 [inline]
 exit_to_user_mode_loop kernel/entry/common.c:171 [inline]
 exit_to_user_mode_prepare+0x174/0x180 kernel/entry/common.c:204
 __syscall_exit_to_user_mode_work kernel/entry/common.c:286 [inline]
 syscall_exit_to_user_mode+0x1a/0x30 kernel/entry/common.c:297
 do_syscall_64+0x4b/0x90 arch/x86/entry/common.c:86
 entry_SYSCALL_64_after_hwframe+0x72/0xdc

read to 0xffff88800d0f8aec of 1 bytes by task 222 on cpu 1:
 unix_poll+0xa3/0x2a0 net/unix/af_unix.c:3170
 sock_poll+0xcf/0x2b0 net/socket.c:1385
 vfs_poll include/linux/poll.h:88 [inline]
 ep_item_poll.isra.0+0x78/0xc0 fs/eventpoll.c:855
 ep_send_events fs/eventpoll.c:1694 [inline]
 ep_poll fs/eventpoll.c:1823 [inline]
 do_epoll_wait+0x6c4/0xea0 fs/eventpoll.c:2258
 __do_sys_epoll_wait fs/eventpoll.c:2270 [inline]
 __se_sys_epoll_wait fs/eventpoll.c:2265 [inline]
 __x64_sys_epoll_wait+0xcc/0x190 fs/eventpoll.c:2265
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x3b/0x90 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x72/0xdc

value changed: 0x00 -> 0x03

Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 222 Comm: dbus-broker Not tainted 6.3.0-rc7-02330-gca6270c12e20 #2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014

Fixes: 3c73419c09a5 ("af_unix: fix 'poll for write'/ connected DGRAM sockets")
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

af_unix: Fix a data race of sk->sk_receive_queue->qlen.

[ Upstream commit 679ed006d416ea0cecfe24a99d365d1dea69c683 ]

KCSAN found a data race of sk->sk_receive_queue->qlen where recvmsg()
updates qlen under the queue lock and sendmsg() checks qlen under
unix_state_sock(), not the queue lock, so the reader side needs
READ_ONCE().

BUG: KCSAN: data-race in __skb_try_recv_from_queue / unix_wait_for_peer

write (marked) to 0xffff888019fe7c68 of 4 bytes by task 49792 on cpu 0:
 __skb_unlink include/linux/skbuff.h:2347 [inline]
 __skb_try_recv_from_queue+0x3de/0x470 net/core/datagram.c:197
 __skb_try_recv_datagram+0xf7/0x390 net/core/datagram.c:263
 __unix_dgram_recvmsg+0x109/0x8a0 net/unix/af_unix.c:2452
 unix_dgram_recvmsg+0x94/0xa0 net/unix/af_unix.c:2549
 sock_recvmsg_nosec net/socket.c:1019 [inline]
 ____sys_recvmsg+0x3a3/0x3b0 net/socket.c:2720
 ___sys_recvmsg+0xc8/0x150 net/socket.c:2764
 do_recvmmsg+0x182/0x560 net/socket.c:2858
 __sys_recvmmsg net/socket.c:2937 [inline]
 __do_sys_recvmmsg net/socket.c:2960 [inline]
 __se_sys_recvmmsg net/socket.c:2953 [inline]
 __x64_sys_recvmmsg+0x153/0x170 net/socket.c:2953
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x3b/0x90 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x72/0xdc

read to 0xffff888019fe7c68 of 4 bytes by task 49793 on cpu 1:
 skb_queue_len include/linux/skbuff.h:2127 [inline]
 unix_recvq_full net/unix/af_unix.c:229 [inline]
 unix_wait_for_peer+0x154/0x1a0 net/unix/af_unix.c:1445
 unix_dgram_sendmsg+0x13bc/0x14b0 net/unix/af_unix.c:2048
 sock_sendmsg_nosec net/socket.c:724 [inline]
 sock_sendmsg+0x148/0x160 net/socket.c:747
 ____sys_sendmsg+0x20e/0x620 net/socket.c:2503
 ___sys_sendmsg+0xc6/0x140 net/socket.c:2557
 __sys_sendmmsg+0x11d/0x370 net/socket.c:2643
 __do_sys_sendmmsg net/socket.c:2672 [inline]
 __se_sys_sendmmsg net/socket.c:2669 [inline]
 __x64_sys_sendmmsg+0x58/0x70 net/socket.c:2669
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x3b/0x90 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x72/0xdc

value changed: 0x0000000b -> 0x00000001

Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 49793 Comm: syz-executor.0 Not tainted 6.3.0-rc7-02330-gca6270c12e20 #2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: datagram: fix data-races in datagram_poll()

[ Upstream commit 5bca1d081f44c9443e61841842ce4e9179d327b6 ]

datagram_poll() runs locklessly, we should add READ_ONCE()
annotations while reading sk->sk_err, sk->sk_shutdown and sk->sk_state.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20230509173131.3263780-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: mscc: ocelot: fix stat counter register values

[ Upstream commit cdc2e28e214fe9315cdd7e069c1c8e2428f93427 ]

Commit d4c367650704 ("net: mscc: ocelot: keep ocelot_stat_layout by reg
address, not offset") organized the stats counters for Ocelot chips, namely
the VSC7512 and VSC7514. A few of the counter offsets were incorrect, and
were caught by this warning:

WARNING: CPU: 0 PID: 24 at drivers/net/ethernet/mscc/ocelot_stats.c:909
ocelot_stats_init+0x1fc/0x2d8
reg 0x5000078 had address 0x220 but reg 0x5000079 has address 0x214,
bulking broken!

Fix these register offsets.

Fixes: d4c367650704 ("net: mscc: ocelot: keep ocelot_stat_layout by reg address, not offset")
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ipvlan:Fix out-of-bounds caused by unclear skb->cb

[ Upstream commit 90cbed5247439a966b645b34eb0a2e037836ea8e ]

If skb enqueue the qdisc, fq_skb_cb(skb)->time_to_send is changed which
is actually skb->cb, and IPCB(skb_in)->opt will be used in
__ip_options_echo. It is possible that memcpy is out of bounds and lead
to stack overflow.
We should clear skb->cb before ip_local_out or ip6_local_out.

v2:
1. clean the stack info
2. use IPCB/IP6CB instead of skb->cb

crash on stable-5.10(reproduce in kasan kernel).
Stack info:
[ 2203.651571] BUG: KASAN: stack-out-of-bounds in
__ip_options_echo+0x589/0x800
[ 2203.653327] Write of size 4 at addr ffff88811a388f27 by task
swapper/3/0
[ 2203.655460] CPU: 3 PID: 0 Comm: swapper/3 Kdump: loaded Not tainted
5.10.0-60.18.0.50.h856.kasan.eulerosv2r11.x86_64 #1
[ 2203.655466] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS rel-1.10.2-0-g5f4c7b1-20181220_000000-szxrtosci10000 04/01/2014
[ 2203.655475] Call Trace:
[ 2203.655481]  <IRQ>
[ 2203.655501]  dump_stack+0x9c/0xd3
[ 2203.655514]  print_address_description.constprop.0+0x19/0x170
[ 2203.655530]  __kasan_report.cold+0x6c/0x84
[ 2203.655586]  kasan_report+0x3a/0x50
[ 2203.655594]  check_memory_region+0xfd/0x1f0
[ 2203.655601]  memcpy+0x39/0x60
[ 2203.655608]  __ip_options_echo+0x589/0x800
[ 2203.655654]  __icmp_send+0x59a/0x960
[ 2203.655755]  nf_send_unreach+0x129/0x3d0 [nf_reject_ipv4]
[ 2203.655763]  reject_tg+0x77/0x1bf [ipt_REJECT]
[ 2203.655772]  ipt_do_table+0x691/0xa40 [ip_tables]
[ 2203.655821]  nf_hook_slow+0x69/0x100
[ 2203.655828]  __ip_local_out+0x21e/0x2b0
[ 2203.655857]  ip_local_out+0x28/0x90
[ 2203.655868]  ipvlan_process_v4_outbound+0x21e/0x260 [ipvlan]
[ 2203.655931]  ipvlan_xmit_mode_l3+0x3bd/0x400 [ipvlan]
[ 2203.655967]  ipvlan_queue_xmit+0xb3/0x190 [ipvlan]
[ 2203.655977]  ipvlan_start_xmit+0x2e/0xb0 [ipvlan]
[ 2203.655984]  xmit_one.constprop.0+0xe1/0x280
[ 2203.655992]  dev_hard_start_xmit+0x62/0x100
[ 2203.656000]  sch_direct_xmit+0x215/0x640
[ 2203.656028]  __qdisc_run+0x153/0x1f0
[ 2203.656069]  __dev_queue_xmit+0x77f/0x1030
[ 2203.656173]  ip_finish_output2+0x59b/0xc20
[ 2203.656244]  __ip_finish_output.part.0+0x318/0x3d0
[ 2203.656312]  ip_finish_output+0x168/0x190
[ 2203.656320]  ip_output+0x12d/0x220
[ 2203.656357]  __ip_queue_xmit+0x392/0x880
[ 2203.656380]  __tcp_transmit_skb+0x1088/0x11c0
[ 2203.656436]  __tcp_retransmit_skb+0x475/0xa30
[ 2203.656505]  tcp_retransmit_skb+0x2d/0x190
[ 2203.656512]  tcp_retransmit_timer+0x3af/0x9a0
[ 2203.656519]  tcp_write_timer_handler+0x3ba/0x510
[ 2203.656529]  tcp_write_timer+0x55/0x180
[ 2203.656542]  call_timer_fn+0x3f/0x1d0
[ 2203.656555]  expire_timers+0x160/0x200
[ 2203.656562]  run_timer_softirq+0x1f4/0x480
[ 2203.656606]  __do_softirq+0xfd/0x402
[ 2203.656613]  asm_call_irq_on_stack+0x12/0x20
[ 2203.656617]  </IRQ>
[ 2203.656623]  do_softirq_own_stack+0x37/0x50
[ 2203.656631]  irq_exit_rcu+0x134/0x1a0
[ 2203.656639]  sysvec_apic_timer_interrupt+0x36/0x80
[ 2203.656646]  asm_sysvec_apic_timer_interrupt+0x12/0x20
[ 2203.656654] RIP: 0010:default_idle+0x13/0x20
[ 2203.656663] Code: 89 f0 5d 41 5c 41 5d 41 5e c3 cc cc cc cc cc cc cc
cc cc cc cc cc cc 0f 1f 44 00 00 0f 1f 44 00 00 0f 00 2d 9f 32 57 00 fb
f4 <c3> cc cc cc cc 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 41 54 be 08
[ 2203.656668] RSP: 0018:ffff88810036fe78 EFLAGS: 00000256
[ 2203.656676] RAX: ffffffffaf2a87f0 RBX: ffff888100360000 RCX:
ffffffffaf290191
[ 2203.656681] RDX: 0000000000098b5e RSI: 0000000000000004 RDI:
ffff88811a3c4f60
[ 2203.656686] RBP: 0000000000000000 R08: 0000000000000001 R09:
ffff88811a3c4f63
[ 2203.656690] R10: ffffed10234789ec R11: 0000000000000001 R12:
0000000000000003
[ 2203.656695] R13: ffff888100360000 R14: 0000000000000000 R15:
0000000000000000
[ 2203.656729]  default_idle_call+0x5a/0x150
[ 2203.656735]  cpuidle_idle_call+0x1c6/0x220
[ 2203.656780]  do_idle+0xab/0x100
[ 2203.656786]  cpu_startup_entry+0x19/0x20
[ 2203.656793]  secondary_startup_64_no_verify+0xc2/0xcb

[ 2203.657409] The buggy address belongs to the page:
[ 2203.658648] page:0000000027a9842f refcount:1 mapcount:0
mapping:0000000000000000 index:0x0 pfn:0x11a388
[ 2203.658665] flags:
0x17ffffc0001000(reserved|node=0|zone=2|lastcpupid=0x1fffff)
[ 2203.658675] raw: 0017ffffc0001000 ffffea000468e208 ffffea000468e208
0000000000000000
[ 2203.658682] raw: 0000000000000000 0000000000000000 00000001ffffffff
0000000000000000
[ 2203.658686] page dumped because: kasan: bad access detected

To reproduce(ipvlan with IPVLAN_MODE_L3):
Env setting:
=======================================================
modprobe ipvlan ipvlan_default_mode=1
sysctl net.ipv4.conf.eth0.forwarding=1
iptables -t nat -A POSTROUTING -s 20.0.0.0/255.255.255.0 -o eth0 -j
MASQUERADE
ip link add gw link eth0 type ipvlan
ip -4 addr add 20.0.0.254/24 dev gw
ip netns add net1
ip link add ipv1 link eth0 type ipvlan
ip link set ipv1 netns net1
ip netns exec net1 ip link set ipv1 up
ip netns exec net1 ip -4 addr add 20.0.0.4/24 dev ipv1
ip netns exec net1 route add default gw 20.0.0.254
ip netns exec net1 tc qdisc add dev ipv1 root netem loss 10%
ifconfig gw up
iptables -t filter -A OUTPUT -p tcp --dport 8888 -j REJECT --reject-with
icmp-port-unreachable
=======================================================
And then excute the shell(curl any address of eth0 can reach):

for((i=1;i<=100000;i++))
do
        ip netns exec net1 curl x.x.x.x:8888
done
=======================================================

Fixes: 2ad7bf363841 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: "t.feng" <fengtao40@huawei.com>
Suggested-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

gve: Remove the code of clearing PBA bit

[ Upstream commit f4c2e67c1773d2a2632381ee30e9139c1e744c16 ]

Clearing the PBA bit from the driver is race prone and it may lead to
dropped interrupt events. This could potentially lead to the traffic
being completely halted.

Fixes: 5e8c5adf95f8 ("gve: DQO: Add core netdev features")
Signed-off-by: Ziwei Xiao <ziweixiao@google.com>
Signed-off-by: Bailey Forrest <bcf@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tcp: add annotations around sk->sk_shutdown accesses

[ Upstream commit e14cadfd80d76f01bfaa1a8d745b1db19b57d6be ]

Now sk->sk_shutdown is no longer a bitfield, we can add
standard READ_ONCE()/WRITE_ONCE() annotations to silence
KCSAN reports like the following:

BUG: KCSAN: data-race in tcp_disconnect / tcp_poll

write to 0xffff88814588582c of 1 bytes by task 3404 on cpu 1:
tcp_disconnect+0x4d6/0xdb0 net/ipv4/tcp.c:3121
__inet_stream_connect+0x5dd/0x6e0 net/ipv4/af_inet.c:715
inet_stream_connect+0x48/0x70 net/ipv4/af_inet.c:727
__sys_connect_file net/socket.c:2001 [inline]
__sys_connect+0x19b/0x1b0 net/socket.c:2018
__do_sys_connect net/socket.c:2028 [inline]
__se_sys_connect net/socket.c:2025 [inline]
__x64_sys_connect+0x41/0x50 net/socket.c:2025
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd

read to 0xffff88814588582c of 1 bytes by task 3374 on cpu 0:
tcp_poll+0x2e6/0x7d0 net/ipv4/tcp.c:562
sock_poll+0x253/0x270 net/socket.c:1383
vfs_poll include/linux/poll.h:88 [inline]
io_poll_check_events io_uring/poll.c:281 [inline]
io_poll_task_func+0x15a/0x820 io_uring/poll.c:333
handle_tw_list io_uring/io_uring.c:1184 [inline]
tctx_task_work+0x1fe/0x4d0 io_uring/io_uring.c:1246
task_work_run+0x123/0x160 kernel/task_work.c:179
get_signal+0xe64/0xff0 kernel/signal.c:2635
arch_do_signal_or_restart+0x89/0x2a0 arch/x86/kernel/signal.c:306
exit_to_user_mode_loop+0x6f/0xe0 kernel/entry/common.c:168
exit_to_user_mode_prepare+0x6c/0xb0 kernel/entry/common.c:204
__syscall_exit_to_user_mode_work kernel/entry/common.c:286 [inline]
syscall_exit_to_user_mode+0x26/0x140 kernel/entry/common.c:297
do_syscall_64+0x4d/0xc0 arch/x86/entry/common.c:86
entry_SYSCALL_64_after_hwframe+0x63/0xcd

value changed: 0x03 -> 0x00

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: add vlan_get_protocol_and_depth() helper

[ Upstream commit 4063384ef762cc5946fc7a3f89879e76c6ec51e2 ]

Before blamed commit, pskb_may_pull() was used instead
of skb_header_pointer() in __vlan_get_protocol() and friends.

Few callers depended on skb->head being populated with MAC header,
syzbot caught one of them (skb_mac_gso_segment())

Add vlan_get_protocol_and_depth() to make the intent clearer
and use it where sensible.

This is a more generic fix than commit e9d3f80935b6
("net/af_packet: make sure to pull mac header") which was
dealing with a similar issue.

kernel BUG at include/linux/skbuff.h:2655 !
invalid opcode: 0000 [#1] SMP KASAN
CPU: 0 PID: 1441 Comm: syz-executor199 Not tainted 6.1.24-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/14/2023
RIP: 0010:__skb_pull include/linux/skbuff.h:2655 [inline]
RIP: 0010:skb_mac_gso_segment+0x68f/0x6a0 net/core/gro.c:136
Code: fd 48 8b 5c 24 10 44 89 6b 70 48 c7 c7 c0 ae 0d 86 44 89 e6 e8 a1 91 d0 00 48 c7 c7 00 af 0d 86 48 89 de 31 d2 e8 d1 4a e9 ff <0f> 0b 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 55 48 89 e5 41
RSP: 0018:ffffc90001bd7520 EFLAGS: 00010286
RAX: ffffffff8469736a RBX: ffff88810f31dac0 RCX: ffff888115a18b00
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffffc90001bd75e8 R08: ffffffff84697183 R09: fffff5200037adf9
R10: 0000000000000000 R11: dffffc0000000001 R12: 0000000000000012
R13: 000000000000fee5 R14: 0000000000005865 R15: 000000000000fed7
FS: 000055555633f300(0000) GS:ffff8881f6a00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020000000 CR3: 0000000116fea000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
[<ffffffff847018dd>] __skb_gso_segment+0x32d/0x4c0 net/core/dev.c:3419
[<ffffffff8470398a>] skb_gso_segment include/linux/netdevice.h:4819 [inline]
[<ffffffff8470398a>] validate_xmit_skb+0x3aa/0xee0 net/core/dev.c:3725
[<ffffffff84707042>] __dev_queue_xmit+0x1332/0x3300 net/core/dev.c:4313
[<ffffffff851a9ec7>] dev_queue_xmit+0x17/0x20 include/linux/netdevice.h:3029
[<ffffffff851b4a82>] packet_snd net/packet/af_packet.c:3111 [inline]
[<ffffffff851b4a82>] packet_sendmsg+0x49d2/0x6470 net/packet/af_packet.c:3142
[<ffffffff84669a12>] sock_sendmsg_nosec net/socket.c:716 [inline]
[<ffffffff84669a12>] sock_sendmsg net/socket.c:736 [inline]
[<ffffffff84669a12>] __sys_sendto+0x472/0x5f0 net/socket.c:2139
[<ffffffff84669c75>] __do_sys_sendto net/socket.c:2151 [inline]
[<ffffffff84669c75>] __se_sys_sendto net/socket.c:2147 [inline]
[<ffffffff84669c75>] __x64_sys_sendto+0xe5/0x100 net/socket.c:2147
[<ffffffff8551d40f>] do_syscall_x64 arch/x86/entry/common.c:50 [inline]
[<ffffffff8551d40f>] do_syscall_64+0x2f/0x50 arch/x86/entry/common.c:80
[<ffffffff85600087>] entry_SYSCALL_64_after_hwframe+0x63/0xcd

Fixes: 469aceddfa3e ("vlan: consolidate VLAN parsing code and limit max parsing depth")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Toke Høiland-Jørgensen <toke@redhat.com>
Cc: Willem de Bruijn <willemb@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: deal with most data-races in sk_wait_event()

[ Upstream commit d0ac89f6f9879fae316c155de77b5173b3e2c9c9 ]

__condition is evaluated twice in sk_wait_event() macro.

First invocation is lockless, and reads can race with writes,
as spotted by syzbot.

BUG: KCSAN: data-race in sk_stream_wait_connect / tcp_disconnect

write to 0xffff88812d83d6a0 of 4 bytes by task 9065 on cpu 1:
tcp_disconnect+0x2cd/0xdb0
inet_shutdown+0x19e/0x1f0 net/ipv4/af_inet.c:911
__sys_shutdown_sock net/socket.c:2343 [inline]
__sys_shutdown net/socket.c:2355 [inline]
__do_sys_shutdown net/socket.c:2363 [inline]
__se_sys_shutdown+0xf8/0x140 net/socket.c:2361
__x64_sys_shutdown+0x31/0x40 net/socket.c:2361
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd

read to 0xffff88812d83d6a0 of 4 bytes by task 9040 on cpu 0:
sk_stream_wait_connect+0x1de/0x3a0 net/core/stream.c:75
tcp_sendmsg_locked+0x2e4/0x2120 net/ipv4/tcp.c:1266
tcp_sendmsg+0x30/0x50 net/ipv4/tcp.c:1484
inet6_sendmsg+0x63/0x80 net/ipv6/af_inet6.c:651
sock_sendmsg_nosec net/socket.c:724 [inline]
sock_sendmsg net/socket.c:747 [inline]
__sys_sendto+0x246/0x300 net/socket.c:2142
__do_sys_sendto net/socket.c:2154 [inline]
__se_sys_sendto net/socket.c:2150 [inline]
__x64_sys_sendto+0x78/0x90 net/socket.c:2150
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd

value changed: 0x00000000 -> 0x00000068

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: annotate sk->sk_err write from do_recvmmsg()

[ Upstream commit e05a5f510f26607616fecdd4ac136310c8bea56b ]

do_recvmmsg() can write to sk->sk_err from multiple threads.

As said before, many other points reading or writing sk_err
need annotations.

Fixes: 34b88a68f26a ("net: Fix use after free in the recvmmsg exit path")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netlink: annotate accesses to nlk->cb_running

[ Upstream commit a939d14919b799e6fff8a9c80296ca229ba2f8a4 ]

Both netlink_recvmsg() and netlink_native_seq_show() read
nlk->cb_running locklessly. Use READ_ONCE() there.

Add corresponding WRITE_ONCE() to netlink_dump() and
__netlink_dump_start()

syzbot reported:
BUG: KCSAN: data-race in __netlink_dump_start / netlink_recvmsg

write to 0xffff88813ea4db59 of 1 bytes by task 28219 on cpu 0:
__netlink_dump_start+0x3af/0x4d0 net/netlink/af_netlink.c:2399
netlink_dump_start include/linux/netlink.h:308 [inline]
rtnetlink_rcv_msg+0x70f/0x8c0 net/core/rtnetlink.c:6130
netlink_rcv_skb+0x126/0x220 net/netlink/af_netlink.c:2577
rtnetlink_rcv+0x1c/0x20 net/core/rtnetlink.c:6192
netlink_unicast_kernel net/netlink/af_netlink.c:1339 [inline]
netlink_unicast+0x56f/0x640 net/netlink/af_netlink.c:1365
netlink_sendmsg+0x665/0x770 net/netlink/af_netlink.c:1942
sock_sendmsg_nosec net/socket.c:724 [inline]
sock_sendmsg net/socket.c:747 [inline]
sock_write_iter+0x1aa/0x230 net/socket.c:1138
call_write_iter include/linux/fs.h:1851 [inline]
new_sync_write fs/read_write.c:491 [inline]
vfs_write+0x463/0x760 fs/read_write.c:584
ksys_write+0xeb/0x1a0 fs/read_write.c:637
__do_sys_write fs/read_write.c:649 [inline]
__se_sys_write fs/read_write.c:646 [inline]
__x64_sys_write+0x42/0x50 fs/read_write.c:646
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd

read to 0xffff88813ea4db59 of 1 bytes by task 28222 on cpu 1:
netlink_recvmsg+0x3b4/0x730 net/netlink/af_netlink.c:2022
sock_recvmsg_nosec+0x4c/0x80 net/socket.c:1017
____sys_recvmsg+0x2db/0x310 net/socket.c:2718
___sys_recvmsg net/socket.c:2762 [inline]
do_recvmmsg+0x2e5/0x710 net/socket.c:2856
__sys_recvmmsg net/socket.c:2935 [inline]
__do_sys_recvmmsg net/socket.c:2958 [inline]
__se_sys_recvmmsg net/socket.c:2951 [inline]
__x64_sys_recvmmsg+0xe2/0x160 net/socket.c:2951
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd

value changed: 0x00 -> 0x01

Fixes: 16b304f3404f ("netlink: Eliminate kmalloc in netlink dump operation.")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bonding: fix send_peer_notif overflow

[ Upstream commit 9949e2efb54eb3001cb2f6512ff3166dddbfb75d ]

Bonding send_peer_notif was defined as u8. Since commit 07a4ddec3ce9
("bonding: add an option to specify a delay between peer notifications").
the bond->send_peer_notif will be num_peer_notif multiplied by
peer_notif_delay, which is u8 * u32. This would cause the send_peer_notif
overflow easily. e.g.

  ip link add bond0 type bond mode 1 miimon 100 num_grat_arp 30 peer_notify_delay 1000

To fix the overflow, let's set the send_peer_notif to u32 and limit
peer_notif_delay to 300s.

Reported-by: Liang Li <liali@redhat.com>
Closes: https://bugzilla.redhat.com/show_bug.cgi?id=2090053
Fixes: 07a4ddec3ce9 ("bonding: add an option to specify a delay between peer notifications")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: conntrack: fix possible bug_on with enable_hooks=1

[ Upstream commit e72eeab542dbf4f544e389e64fa13b82a1b6d003 ]

I received a bug report (no reproducer so far) where we trip over

712         rcu_read_lock();
713         ct_hook = rcu_dereference(nf_ct_hook);
714         BUG_ON(ct_hook == NULL);  // here

In nf_conntrack_destroy().

First turn this BUG_ON into a WARN.  I think it was triggered
via enable_hooks=1 flag.

When this flag is turned on, the conntrack hooks are registered
before nf_ct_hook pointer gets assigned.
This opens a short window where packets enter the conntrack machinery,
can have skb->_nfct set up and a subsequent kfree_skb might occur
before nf_ct_hook is set.

Call nf_conntrack_init_end() to set nf_ct_hook before we register the
pernet ops.

Fixes: ba3fbe663635 ("netfilter: nf_conntrack: provide modparam to always register conntrack hooks")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>