arm64: dts: ls1043a: Add SCFG phandle for PCIe nodes

The LS1043A PCIe controller has some control registers
in SCFG block, so add the SCFG phandle for each PCIe
controller node.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: ls1043a: use pcie aer/pme interrupts

After the binding has been updated to include more specific interrupt
definition, update the dts to use the more specific interrupt names.

Signed-off-by: Po Liu <po.liu@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: ls1043a: Enable usb3-lpm-capable for usb3 node

Enable USB3 HW LPM feature for ls1043a.

Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: ls1043a: fix the wrong size of dcfg space

The size of the block should be 0x1000 instead of 0x10000.

Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: ls208x: remove NXP Erratum A008585 from LS2088A.

NXP Erratum A008585 affects A57 core cluster used in LS2085 rev1.
However this problem has been fixed in A72 core cluster used in LS2088.
Therefore remove the erratum from LS2088A. Keeping it only in LS2085.

Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: Sandeep Malik <sandeep.malik@nxp.com>
Acked-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: ls208xa-rdb: fix errata E-00013

Specify a channel zero in idle state to avoid enterring tri-stated state
for PCA9547.

Some information about E-00013:
- Description: I2C1 and I2C3 buses are missing pull-up.
- Impact: When the PCA954x device is tri-stated, the I2C bus will float.
  This makes the I2C bus and its associated downstream devices
  inaccessible.
- Hardware fix: Populate resistors R189 and R190 for I2C1 and resistors
  R228 and R229 for I2C3.
- Software fix: Remove the tri-state option from the PCA954x
  driver(PCA954x always on enable status, specify a channel zero in dts to
  fix the errata E-00013).

Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: ls2081a-rdb: Add DTS for NXP LS2081ARDB

This patch adds support for NXP LS2081ARDB board which has LS2081A SoC.

LS2081A SoC is 40-pin derivative of LS2088A SoC. From functional
perspective both are same. Hence, LS2088a SoC dtsi file is included
from LS2081ARDB dts.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Tao Yang <b31903@freescale.com>
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: ls2080a-rdb: add phy nodes

Define PHY nodes on the board.

Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: ls208xa-qds: add mdio mux nodes from on-board FPGA

Update the cpld node name to be generic board-contrl and add mmio mdio
mux nodes from the on-board FPGA.

Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mp-venice-gw74xx: add PCIe support

Add PCIe support on the Gateworks GW74xx board. While at it,
fix the related gpio line names from the previous incorrect values.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: freescale: add support for i.MX8DXL EVK board

This is to support the EVK (Evaluation Kit Board) for the i.MX8DXL.
The patch has enabled the serial console, SD/EMMC interface, and
the eqos and fec ethernet network.

Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: freescale: add i.MX8DXL SoC support

i.MX8DXL is a device targeting the automotive and industrial market
segments. The chip is designed to achieve both high performance and
low power consumption. It has a dual (2x) Cortex-A35 processor.

This patch adds the basic support for i.MX8DXL SoC.

Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8: add a node label to ddr-pmu

The ddr-pmu on i.mx8dxl has a different interrupt number.
Add a node label to ddr-pmu so that it could be referred
and changed in i.mx8dxl dts.

Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx: Add i.mx8mm Gateworks gw7904 dts support

The GW7904 is based on the i.MX 8M Mini SoC featuring:
 - LPDDR4 DRAM
 - eMMC FLASH
 - microSD connector with UHS support
 - LIS2DE12 3-axis accelerometer
 - Gateworks System Controller
 - IMX8M FEC
 - 2x RS232 off-board connectors
 - PMIC
 - 10x bi-color LED's
 - 1x miniPCIe socket with PCIe and USB2.0
 - 802.3at Class 4 PoE
 - 10-30VDC input via barrel-jack

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mp-venice-gw74xx: add WiFi/BT module support

The GW74xx supports an on-board Laird Connectivity Sterling LWB5+ module
which uses a Cypress CYW4373W chip to provide 1x1 802.11 a/b/g/n/ac +
Bluetooth 5.2.

Add the proper device-tree nodes for it.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mp-venice-gw74xx: add cpu-supply node for cpufreq

Add regulator config for cpu-supply in order to support cpufreq.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mp-venice-gw74xx: add USB DR support

Add support for USB DR on USB1 interface. Host/Device detection is done
using the usb-role-switch connector with a GPIO as USB1_OTG_ID is not
connected internally.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx93: add mediamix blk ctrl node

Add i.MX93 mediamix blk ctrl node

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx93: add src node

Add i.MX93 SRC node

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: ls1028a-rdb: add more ethernet aliases

Commit "arm64: dts: ls1028a: enable swp5 and eno3 for all boards" which
Shawn declared as applied, but for which I can't find a sha1sum, has
enabled a new Ethernet port on the LS1028A-RDB (&enetc_port3), but
U-Boot, which passes a MAC address to Linux' device tree through the
/aliases node, fails to do this for this newly enabled port.

Fix that by adding more ethernet aliases in the only
backwards-compatible way possible: at the end of the current list.

And since it is possible to very easily convert either swp4 or swp5 to
DSA user ports now (which have a MAC address of their own), using these
U-Boot commands:

=> fdt addr $fdt_addr_r
=> fdt rm /soc/pcie@1f0000000/ethernet-switch@0,5/ports/port@4 ethernet

it would be good if those DSA user ports (swp4, swp5) gained a valid MAC
address from U-Boot as well. In order for that to work properly,
provision two more ethernet aliases for &mscc_felix_port{4,5} as well.

The resulting ordering is slightly unusual, but to me looks more natural
than eno0, eno2, swp0, swp1, swp2, swp3, eno3, swp4, swp5.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mq: update sdma node name format

Node names should be generic, so change the sdma node name format 'sdma'
into 'dma-controller'.

Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx93: add lpspi nodes

Add i.MX93 lpspi nodes

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx93: add lpi2c nodes

Add i.MX93 lpi2c nodes

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx93: add a55 pmu

Add A55 PMU node for perf usage

Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx93: add blk ctrl node

Add i.MX93 BLK CTRL MIX node

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx93: add s4 mu node

Add s4 mu node for sentinel communication

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx93: add gpio clk

Add the GPIO clk, otherwise GPIO may not work if clk driver disable the
GPIO clk during kernel boot.

Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx93: correct SDHC clk entry

DUMMY clk only works with clk_ignore_unused and bootloader enables those
clks that required for SDHC work properly.

Correct SDHC clk entry with real clk.

Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: tqma8mpql: add USB DR support

Add support for USB DR on USB1 interface. Host/Device detection is done
using the usb-role-switch connector.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: verdin-imx8mm: introduce hdmi-connector

The Lontium LT8912B driver needs a HDMI connector to be connected to
port 1. Introduce this connector to be enabled in a device tree overlay.

Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: verdin-imx8mm: add lvds panel node

Add an LVDS panel node to be extended by a device tree overlay.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: verdin-imx8mm: rename sn65dsi83 to sn65dsi84

Rename sn65dsi83 to sn65dsi84 as that is the exact chip used on the
Verdin DSI to LVDS Adapter.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8ulp: increase the clock speed of LPSPI

LPSPI transfer max speed is half of the root clock.
Increase the root clock speed to support faster data transmission.

And update the parent clock of all i2c/spi with IMX8ULP_CLK_FROSC_DIV2
which could produce accurate clock for i2c/spi usage.

Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8ulp: add mailbox node

Add Sentinel Message Unit(MU), Generic MU nodes.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8ulp: add pmu node

Add i.MX8ULP pmu node

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8ulp: correct the scmi sram node name

Follow sram/sram.yaml to update the sram node name.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8ulp: drop undocumented property in cgc

The clocks and clocks-names are not documented in binding doc,
and the clk-imx8ulp driver not use the undocumented property,
so drop them.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mq-librem5: fix mipi_csi description

Properties are not documented so lead to the following error:
'#address-cells', '#size-cells', 'interrupts' do not match any of the regexes: 'pinctrl-[0-9]+'

Fix this by removing unneeded properties.

Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mq-librem5: add usb-role-switch property to dwc3

In order to enable (PD and data) role switching on the Librem 5 phone,
add the usb-role-switch property to imx8mq's dwc3 node.

Signed-off-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mq-librem5: add USB type-c properties for role switching

Add the connector properties to the USB type-c stanza to enable (PD)
role-switching on the Librem 5 phone.

Signed-off-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mq-librem5: Add bq25895 as max17055's power supply

This allows the userspace to notice that there's not enough
current provided to charge the battery, and also fixes issues
with 0% SOC values being considered invalid.

Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mq-librem5: add RGB pwm notification leds

Describe the RGB notification leds on the Librem 5 phone.
Use the common defines so we're sure to adhere to the common patterns,
use predefined led colors and functions so we're being warned in case
of deprecations.

Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mq-librem5: describe the voice coil motor for focus control

Describe the focus motor that will be used for the rear camera - even
though the rear camera sensor driver is not yet in the mainline. The
focus motor is a separate device and can be controlled already.

Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: ls1028a: enable swp5 and eno3 for all boards

In order for the LS1028A based boards to benefit from support for
multiple CPU ports, the second DSA master and its associated CPU port
must be enabled in the device trees. This does not change the default
CPU port from the current port 4.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: ls1028a: mark enetc port 3 as a DSA master too

The LS1028A switch has 2 internal links to the ENETC controller.

With DSA's ability to support multiple CPU ports, we should mark both
ENETC ports as DSA masters.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: ls1028a: move DSA CPU port property to the common SoC dtsi

Since the CPU port 4 of the switch is hardwired inside the SoC to go to
the enetc port 2, this shouldn't be something that the board files need
to set (but whether that CPU port is used or not is another discussion).

So move the DSA "ethernet" property to the common dtsi.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mp-evk: Add PCIe support

Add PCIe support on i.MX8MP EVK board.

Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Tested-by: Marek Vasut <marex@denx.de>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mp: Add iMX8MP PCIe support

Add i.MX8MP PCIe support.

Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Tested-by: Marek Vasut <marex@denx.de>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8ulp: no executable source file permission

This fixes the following error:

arch/arm64/boot/dts/freescale/imx8ulp-pinfunc.h: error: do not set
 execute permissions for source files

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mp: Add SNVS LPGPR

Add SNVS LPGPR bindings to MX8M Plus, the LPGPR is used to store
e.g. boot counter.

Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mp-msc-sm2s: Add device trees for MSC SM2S-IMX8PLUS SoM and carrier board

Add device trees for one of a number of MSC's (parent company, Avnet)
variants of the SM2S-IMX8PLUS system on module along with the compatible
SM2S-SK-AL-EP1 carrier board. As the name suggests, this family of SoMs use
the NXP i.MX8MP SoC and provide the SMARC module interface.

Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mm: Fix typo in license text for Engicam boards

Fix the Amarula Solutions typo mistake in license text for Engicam
i.MX8M boards add in below commits.

commit <60ac35268f85b> ("arm64: dts: imx8mm: Add Engicam i.Core MX8M
Mini SoM")
commit <aec8ad34f7f24> ("arm64: dts: imx8mp: Add Engicam i.Core MX8M
Plus EDIMM2.2 Starter Kit")
commit <eefe06b295087> ("arm64: dts: imx8mp: Add Engicam i.Core MX8M
Plus SoM")

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8-ss-dma: add IPG clock for i2c

i.MX8 LPI2C requires both PER and IPG clock, so add the missed IPG clk.

Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: Add support for Kontron SL/BL i.MX8MM OSM-S

This adds support for the Kontron Electronics SL i.MX8MM OSM-S SoM
and the matching baseboard BL i.MX8MM OSM-S.

The SoM hardware complies to the Open Standard Module (OSM) 1.0
specification, size S (https://sget.org/standards/osm).

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mm-kontron: Add SPI NOR partition layout

This is the layout used by the bootloader. Add it to the kernel
devicetree to make the same layout available in Linux and have
the devicetrees synced.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mm-kontron: Use voltage rail names from schematic for PMIC regulator-names

Improve the naming of the regulators to contain the voltage rail
names from the schematic.

Suggested-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mm-kontron: Remove low DDRC operating point

For some reason there is a problem with finding a DDR configuration
that works on all operating points and all LPDDR4 types used on the
SoM. Therefore the bootloader currently doesn't configure the lowest
of the three operating points. Let's also skip this in the kernel
devicetree to make sure it isn't used.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mm-kontron: Use the VSELECT signal to switch SD card IO voltage

It turns out that it is not necessary to declare the VSELECT signal as
GPIO and let the PMIC driver set it to a fixed high level. This switches
the voltage between 3.3V and 1.8V by setting the PMIC register for LDO5
accordingly.

Instead we can do it like other boards already do and simply mux the
VSELECT signal of the USDHC interface to the pin. This makes sure that
the correct voltage is selected by setting the PMIC's SD_VSEL input
to high or low accordingly.

Reported-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mm-kontron: Adjust compatibles, file names and model strings

The official naming includes "SL" (SoM-Line) or "BL" (Board-Line).
By updating we make sure, that we can maintain this more easily in
future and make sure that the proper devicetree can be selected for
the hardware.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mp: add VPU blk ctrl node

Add i.MX8MP VPU blk ctrl node

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mp: add vpu pgc nodes

Add i.MX8MP PGC nodes for vpu, which are used to supply power for VPU.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mp-verdin: add cpu-supply

Add the cpu-supply property to all CPU nodes to enable the cpufreq
driver.

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mm-venice-gw7903: add digital I/O ctl gpios

The GW7903-C revision introduced two additional GPIO's for controlling
the digital I/O direction. Add them.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mm/n-venice-gw7902: Remove invalid property

The 'oscillator-frequency' property is not documented and it is
not used anywhere. Remove it.

Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mp: Add SoM compatible to i.MX8M Plus DHCOM PDK2

Add SoM compatible string into i.MX8MP DHCOM PDK2 compatible strings.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mp: Drop Atheros PHY header from i.MX8M Plus DHCOM PDK2

This PHY is not used on PDK2, the header was added due to copy-paste
error, drop it.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mp: Add HW variant details to i.MX8M Plus DHCOM PDK2

Add information about which exact SoM variant is used on which PDK2 variant.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: mnt-reform2: don't use multiple blank lines

Avoid the following checkpatch warning:

arch/arm/boot/dts/imx8mq-mnt-reform2.dts:213: check: Please don't use
 multiple blank lines

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mp-verdin: don't use multiple blank lines

Avoid the following checkpatch warning:

arch/arm/boot/dts/imx8mp-verdin.dtsi:281: check: Please don't use
 multiple blank lines

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mm-venice-gw72xx-0x: blank line at end of file

Avoid the following checkpatch warning:

Found possible blank line(s) at end of file
 'arch/arm/boot/dts/imx8mm-venice-gw72xx-0x.dts'

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8ulp-evk: Add the fec support

Enable the fec on i.MX8ULP EVK board.

Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8ulp: Add the fec support

Add the fec support on i.MX8ULP platforms.

Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mp: add interconnect for hsio blk ctrl

Add interconnect property for hsio blk ctrl

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arm64: dts: imx8mp: add interconnects for media blk ctrl

Add interconnect property for media blk ctrl

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

dt-bindings: arm: imx: update fsl.yaml for imx8dxl

i.MX8DXL is a device targeting the automotive and industrial market
segments. The chip is designed to achieve both high performance and
low power consumption. It has a dual (2x) Cortex-A35 processor.

Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

dt-bindings: firmware: add missing resource IDs for imx8dxl

Add the missing resource IDs for imx8dxl.

Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

dt-bindings: arm: Add i.MX8M Mini Gateworks GW7904 board

Add DT compatible string for i.MX8M Mini based Gateworks GW7904 board.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

dt-bindings: soc: add i.MX93 mediamix blk ctrl

Add DT bindings for i.MX93 MEDIAMIX BLK CTRL.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

dt-bindings: soc: add i.MX93 SRC

Add bindings for i.MX93 System Reset Controller(SRC). SRC supports
resets and power gating for mixes.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

dt-bindings: mfd: syscon: Add i.MX93 blk ctrl system registers

Document i.MX93 BLK CTRL system registers.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

dt-bindings: arm: fsl: Add MSC SM2S-IMX8PLUS SoM and SM2-MB-EP1 Carrier

Add DT compatible strings for a combination of the 14N0600E variant of
the Avnet (MSC branded) SM2S-IMX8PLUS SoM on it's own and in combination
with the SM2-MB-EP1 carrier board.

Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

dt-bindings: arm: fsl: Add Kontron BL i.MX8MM OSM-S board

Add bindings for the Kontron BL i.MX8MM OSM-S board.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

dt-bindings: arm: fsl: Rename compatibles for Kontron i.MX8MM SoM/board

This updates the bindings in order to use names for the boards that
follow the latest convention used by Kontron marketing.

By updating we make sure, that we can maintain this more easily in
future and make sure that the proper devicetree can be selected for
the hardware.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

dt-bindings: soc: imx: add i.MX8MP vpu blk ctrl

i.MX8MP VPU blk ctrl module has similar design as i.MX8MM, so reuse
the i.MX8MM VPU blk ctrl yaml file. And add description for the items.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

dt-bindings: soc: imx: add interconnect property for i.MX8MM vpu blk ctrl

i.MX8MM VPU support NoC QoS setting, so add interconnect property
for i.MX8MM VPU blk ctrl

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

dt-bindings: soc: imx: drop minItems for i.MX8MM vpu blk ctrl

minItems and maxItems are set as the same value. In such case minItems is
not necessary. So drop it.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

dt-bindings: power: imx8mp-power: add HDMI HDCP/HRV

Add i.MX8MP HDMI HDCP and HRV entries.

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

dt-bindings: arm: fsl: imx6ul-kontron: Update bindings

This updates the bindings in order to simplify the devicetree
structure and to add names for the boards that follow the latest
convention used by Kontron marketing.

It also gets rid of the N6xxx notation in the compatibles and
file names, as they are not really used anymore and often result
in confusion.

This is a breaking change, but the impact shouldn't be too big
and it makes usage and maintenance easier in the future.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

dt-bindings: clk: imx8mm: don't use multiple blank lines

Avoid the following checkpatch warning:

include/dt-bindings/clock/imx8mm-clock.h:284: check: Please don't use
 multiple blank lines

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

dt-bindings: soc: imx: add interconnect property for i.MX8MP hsio blk ctrl

Add interconnect property for i.MX8MP hsio blk ctrl

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

dt-bindings: soc: imx: add interconnect property for i.MX8MP hdmi blk ctrl

Add interconnect property for i.MX8MP hdmi blk ctrl

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

dt-bindings: soc: imx: add interconnect property for i.MX8MP media blk ctrl

Add interconnect property for i.MX8MP mediamix blk ctrl

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Linux 6.0-rc1

radix-tree: replace gfp.h inclusion with gfp_types.h

Radix tree header includes gfp.h for __GFP_BITS_SHIFT only. Now we
have gfp_types.h for this.

Fixes powerpc allmodconfig build:

   In file included from include/linux/nodemask.h:97,
                    from include/linux/mmzone.h:17,
                    from include/linux/gfp.h:7,
                    from include/linux/radix-tree.h:12,
                    from include/linux/idr.h:15,
                    from include/linux/kernfs.h:12,
                    from include/linux/sysfs.h:16,
                    from include/linux/kobject.h:20,
                    from include/linux/pci.h:35,
                    from arch/powerpc/kernel/prom_init.c:24:
   include/linux/random.h: In function 'add_latent_entropy':
>> include/linux/random.h:25:46: error: 'latent_entropy' undeclared (first use in this function); did you mean 'add_latent_entropy'?
      25 |         add_device_randomness((const void *)&latent_entropy, sizeof(latent_entropy));
         |                                              ^~~~~~~~~~~~~~
         |                                              add_latent_entropy
   include/linux/random.h:25:46: note: each undeclared identifier is reported only once for each function it appears in

Reported-by: kernel test robot <lkp@intel.com>
CC: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'pull-fixes' of git://git./linux/kernel/git/viro/vfs

Pull vfs lseek fix from Al Viro:
 "Fix proc_reg_llseek() breakage. Always had been possible if somebody
  left NULL ->proc_lseek, became a practical issue now"

* tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  take care to handle NULL ->proc_lseek()

take care to handle NULL ->proc_lseek()

Easily done now, just by clearing FMODE_LSEEK in ->f_mode
during proc_reg_open() for such entries.

Fixes: 868941b14441 "fs: remove no_llseek"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Merge tag 'for-linus-6.0-rc1b-tag' of git://git./linux/kernel/git/xen/tip

Pull more xen updates from Juergen Gross:

 - fix the handling of the "persistent grants" feature negotiation
   between Xen blkfront and Xen blkback drivers

 - a cleanup of xen.config and adding xen.config to Xen section in
   MAINTAINERS

 - support HVMOP_set_evtchn_upcall_vector, which is more compliant to
   "normal" interrupt handling than the global callback used up to now

 - further small cleanups

* tag 'for-linus-6.0-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  MAINTAINERS: add xen config fragments to XEN HYPERVISOR sections
  xen: remove XEN_SCRUB_PAGES in xen.config
  xen/pciback: Fix comment typo
  xen/xenbus: fix return type in xenbus_file_read()
  xen-blkfront: Apply 'feature_persistent' parameter when connect
  xen-blkback: Apply 'feature_persistent' parameter when connect
  xen-blkback: fix persistent grants negotiation
  x86/xen: Add support for HVMOP_set_evtchn_upcall_vector

Merge tag 'perf-tools-fixes-for-v6.0-2022-08-13' of git://git./linux/kernel/git/acme/linux

Pull more perf tool updates from Arnaldo Carvalho de Melo:

 - 'perf c2c' now supports ARM64, adjust its output to cope with
   differences with what is in x86_64. Now go find false sharing on
   ARM64 (at least Neoverse) as well!

 - Refactor the JSON processing, making the output more compact and thus
   reducing the size of the resulting perf binary

 - Improvements for 'perf offcpu' profiling, including tracking child
   processes

 - Update Intel JSON metrics and events files for broadwellde,
   broadwellx, cascadelakex, haswellx, icelakex, ivytown, jaketown,
   knightslanding, sapphirerapids, skylakex and snowridgex

 - Add 'perf stat' JSON output and a 'perf test' entry for it

 - Ignore memfd and anonymous mmap events if jitdump present

 - Refactor 'perf test' shell tests allowing subdirs

 - Fix an error handling path in 'parse_perf_probe_command()'

 - Fixes for the guest Intel PT tracing patchkit in the 1st batch of
   this merge window

 - Print debuginfod queries if -v option is used, to explain delays in
   processing when debuginfo servers are enabled to fetch DSOs with
   richer symbol tables

 - Improve error message for 'perf record -p not_existing_pid'

 - Fix openssl and libbpf feature detection

 - Add PMU pai_crypto event description for IBM z16 on 'perf list'

 - Fix typos and duplicated words on comments in various places

* tag 'perf-tools-fixes-for-v6.0-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (81 commits)
  perf test: Refactor shell tests allowing subdirs
  perf vendor events: Update events for snowridgex
  perf vendor events: Update events and metrics for skylakex
  perf vendor events: Update metrics for sapphirerapids
  perf vendor events: Update events for knightslanding
  perf vendor events: Update metrics for jaketown
  perf vendor events: Update metrics for ivytown
  perf vendor events: Update events and metrics for icelakex
  perf vendor events: Update events and metrics for haswellx
  perf vendor events: Update events and metrics for cascadelakex
  perf vendor events: Update events and metrics for broadwellx
  perf vendor events: Update metrics for broadwellde
  perf jevents: Fold strings optimization
  perf jevents: Compress the pmu_events_table
  perf metrics: Copy entire pmu_event in find metric
  perf pmu-events: Hide the pmu_events
  perf pmu-events: Don't assume pmu_event is an array
  perf pmu-events: Move test events/metrics to JSON
  perf test: Use full metric resolution
  perf pmu-events: Hide pmu_events_map
  ...

Merge tag 'powerpc-6.0-2' of git://git./linux/kernel/git/powerpc/linux

Pull powerpc fixes from Michael Ellerman:

 - Ensure we never emit lwarx with EH=1 on 32-bit, because some 32-bit
   CPUs trap on it rather than ignoring it as they should.

 - Fix ftrace when building with clang, which was broken by some
   refactoring.

 - A couple of other minor fixes.

Thanks to Christophe Leroy, Naveen N.  Rao, Nick Desaulniers, Ondrej
Mosnacek, Pali Rohár, Russell Currey, and Segher Boessenkool.

* tag 'powerpc-6.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/kexec: Fix build failure from uninitialised variable
  powerpc/ppc-opcode: Fix PPC_RAW_TW()
  powerpc64/ftrace: Fix ftrace for clang builds
  powerpc: Make eh value more explicit when using lwarx
  powerpc: Don't hide eh field of lwarx behind a macro
  powerpc: Fix eh field when calling lwarx on PPC32

Merge tag 'pull-work.misc' of git://git./linux/kernel/git/viro/vfs

Pull /proc/mounts fix from Al Viro:
 "Fix for /proc/mounts escaping - escape the '#' character too"

* tag 'pull-work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  vfs: escape hash as well