YueHaibing [Fri, 16 Aug 2019 14:05:13 +0000 (22:05 +0800)]
rtlwifi: remove unused variables 'RTL8712_SDIO_EFUSE_TABLE' and 'MAX_PGPKT_SIZE'
drivers/net/wireless/realtek/rtlwifi/efuse.c:16:31:
warning: RTL8712_SDIO_EFUSE_TABLE defined but not used [-Wunused-const-variable=]
drivers/net/wireless/realtek/rtlwifi/efuse.c:9:17:
warning: MAX_PGPKT_SIZE defined but not used [-Wunused-const-variable=]
They are never used, so can be removed.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Larry Finger [Mon, 12 Aug 2019 19:27:41 +0000 (14:27 -0500)]
rtlwifi: rtl8192cu: Fix value set in descriptor
In the process of converting the bit manipulation macros were converted
to use GENMASK(), the compiler reported a value too big for the field.
The offending statement was trying to write 0x100 into a 5-bit field.
An accompaning comment says to set bit 3, thus the code is changed
appropriately.
This error has been in the driver since its initial submission.
Fixes:
29d00a3e46bb ("rtlwifi: rtl8192cu: Add routine trx")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Valdis Klētnieks [Thu, 8 Aug 2019 01:51:58 +0000 (21:51 -0400)]
rtlwifi: fix non-kerneldoc comment in usb.c
Fix spurious warning message when building with W=1:
CC [M] drivers/net/wireless/realtek/rtlwifi/usb.o
drivers/net/wireless/realtek/rtlwifi/usb.c:243: warning: Cannot understand * on line 243 - I thought it was a doc line
drivers/net/wireless/realtek/rtlwifi/usb.c:760: warning: Cannot understand * on line 760 - I thought it was a doc line
drivers/net/wireless/realtek/rtlwifi/usb.c:790: warning: Cannot understand * on line 790 - I thought it was a doc line
Clean up the comment format.
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
David S. Miller [Mon, 2 Sep 2019 19:07:46 +0000 (12:07 -0700)]
Merge branch 'mvpp2-per-cpu-buffers'
Matteo Croce says:
====================
mvpp2: per-cpu buffers
This patchset workarounds an PP2 HW limitation which prevents to use
per-cpu rx buffers.
The first patch is just a refactor to prepare for the second one.
The second one allocates percpu buffers if the following conditions are met:
- CPU number is less or equal 4
- no port is using jumbo frames
If the following conditions are not met at load time, of jumbo frame is enabled
later on, the shared allocation is reverted.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Matteo Croce [Mon, 2 Sep 2019 10:21:37 +0000 (12:21 +0200)]
mvpp2: percpu buffers
Every mvpp2 unit can use up to 8 buffers mapped by the BM (the HW buffer
manager). The HW will place the frames in the buffer pool depending on the
frame size: short (< 128 bytes), long (< 1664) or jumbo (up to 9856).
As any unit can have up to 4 ports, the driver allocates only 2 pools,
one for small and one long frames, and share them between ports.
When the first port MTU is set higher than 1664 bytes, a third pool is
allocated for jumbo frames.
This shared allocation makes impossible to use percpu allocators,
and creates contention between HW queues.
If possible, i.e. if the number of possible CPU are less than 8 and jumbo
frames are not used, switch to a new scheme: allocate 8 per-cpu pools for
short and long frames and bind every pool to an RXQ.
When the first port MTU is set higher than 1664 bytes, the allocation
scheme is reverted to the old behaviour (3 shared pools), and when all
ports MTU are lowered, the per-cpu buffers are allocated again.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matteo Croce [Mon, 2 Sep 2019 10:21:36 +0000 (12:21 +0200)]
mvpp2: refactor BM pool functions
Refactor mvpp2_bm_pool_create(), mvpp2_bm_pool_destroy() and
mvpp2_bm_pools_init() so that they accept a struct device instead
of a struct platform_device, as they just need platform_device->dev.
Removing such dependency makes the BM code more reusable in context
where we don't have a pointer to the platform_device.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sat, 31 Aug 2019 12:46:19 +0000 (15:46 +0300)]
net: dsa: Fix off-by-one number of calls to devlink_port_unregister
When a function such as dsa_slave_create fails, currently the following
stack trace can be seen:
[ 2.038342] sja1105 spi0.1: Probed switch chip: SJA1105T
[ 2.054556] sja1105 spi0.1: Reset switch and programmed static config
[ 2.063837] sja1105 spi0.1: Enabled switch tagging
[ 2.068706] fsl-gianfar soc:ethernet@2d90000 eth2: error -19 setting up slave phy
[ 2.076371] ------------[ cut here ]------------
[ 2.080973] WARNING: CPU: 1 PID: 21 at net/core/devlink.c:6184 devlink_free+0x1b4/0x1c0
[ 2.088954] Modules linked in:
[ 2.092005] CPU: 1 PID: 21 Comm: kworker/1:1 Not tainted 5.3.0-rc6-01360-g41b52e38d2b6-dirty #1746
[ 2.100912] Hardware name: Freescale LS1021A
[ 2.105162] Workqueue: events deferred_probe_work_func
[ 2.110287] [<
c03133a4>] (unwind_backtrace) from [<
c030d8cc>] (show_stack+0x10/0x14)
[ 2.117992] [<
c030d8cc>] (show_stack) from [<
c10b08d8>] (dump_stack+0xb4/0xc8)
[ 2.125180] [<
c10b08d8>] (dump_stack) from [<
c0349d04>] (__warn+0xe0/0xf8)
[ 2.132018] [<
c0349d04>] (__warn) from [<
c0349e34>] (warn_slowpath_null+0x40/0x48)
[ 2.139549] [<
c0349e34>] (warn_slowpath_null) from [<
c0f19d74>] (devlink_free+0x1b4/0x1c0)
[ 2.147772] [<
c0f19d74>] (devlink_free) from [<
c1064fc0>] (dsa_switch_teardown+0x60/0x6c)
[ 2.155907] [<
c1064fc0>] (dsa_switch_teardown) from [<
c1065950>] (dsa_register_switch+0x8e4/0xaa8)
[ 2.164821] [<
c1065950>] (dsa_register_switch) from [<
c0ba7fe4>] (sja1105_probe+0x21c/0x2ec)
[ 2.173216] [<
c0ba7fe4>] (sja1105_probe) from [<
c0b35948>] (spi_drv_probe+0x80/0xa4)
[ 2.180920] [<
c0b35948>] (spi_drv_probe) from [<
c0a4c1cc>] (really_probe+0x108/0x400)
[ 2.188711] [<
c0a4c1cc>] (really_probe) from [<
c0a4c694>] (driver_probe_device+0x78/0x1bc)
[ 2.196933] [<
c0a4c694>] (driver_probe_device) from [<
c0a4a3dc>] (bus_for_each_drv+0x58/0xb8)
[ 2.205414] [<
c0a4a3dc>] (bus_for_each_drv) from [<
c0a4c024>] (__device_attach+0xd0/0x168)
[ 2.213637] [<
c0a4c024>] (__device_attach) from [<
c0a4b1d0>] (bus_probe_device+0x84/0x8c)
[ 2.221772] [<
c0a4b1d0>] (bus_probe_device) from [<
c0a4b72c>] (deferred_probe_work_func+0x84/0xc4)
[ 2.230686] [<
c0a4b72c>] (deferred_probe_work_func) from [<
c03650a4>] (process_one_work+0x218/0x510)
[ 2.239772] [<
c03650a4>] (process_one_work) from [<
c03660d8>] (worker_thread+0x2a8/0x5c0)
[ 2.247908] [<
c03660d8>] (worker_thread) from [<
c036b348>] (kthread+0x148/0x150)
[ 2.255265] [<
c036b348>] (kthread) from [<
c03010e8>] (ret_from_fork+0x14/0x2c)
[ 2.262444] Exception stack(0xea965fb0 to 0xea965ff8)
[ 2.267466] 5fa0:
00000000 00000000 00000000 00000000
[ 2.275598] 5fc0:
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 2.283729] 5fe0:
00000000 00000000 00000000 00000000 00000013 00000000
[ 2.290333] ---[ end trace
ca5d506728a0581a ]---
devlink_free is complaining right here:
WARN_ON(!list_empty(&devlink->port_list));
This happens because devlink_port_unregister is no longer done right
away in dsa_port_setup when a DSA_PORT_TYPE_USER has failed.
Vivien said about this change that:
Also no need to call devlink_port_unregister from within dsa_port_setup
as this step is inconditionally handled by dsa_port_teardown on error.
which is not really true. The devlink_port_unregister function _is_
being called unconditionally from within dsa_port_setup, but not for
this port that just failed, just for the previous ones which were set
up.
ports_teardown:
for (i = 0; i < port; i++)
dsa_port_teardown(&ds->ports[i]);
Initially I was tempted to fix this by extending the "for" loop to also
cover the port that failed during setup. But this could have potentially
unforeseen consequences unrelated to devlink_port or even other types of
ports than user ports, which I can't really test for. For example, if
for some reason devlink_port_register itself would fail, then
unconditionally unregistering it in dsa_port_teardown would not be a
smart idea. The list might go on.
So just make dsa_port_setup undo the setup it had done upon failure, and
let the for loop undo the work of setting up the previous ports, which
are guaranteed to be brought up to a consistent state.
Fixes:
955222ca5281 ("net: dsa: use a single switch statement for port setup")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Fri, 30 Aug 2019 08:25:30 +0000 (10:25 +0200)]
mlx5: Add missing init_net check in FIB notifier
Take only FIB events that are happening in init_net into account. No other
namespaces are supported.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 2 Sep 2019 18:20:17 +0000 (11:20 -0700)]
Merge git://git./linux/kernel/git/netdev/net
r8152 conflicts are the NAPI fixes in 'net' overlapping with
some tasklet stuff in net-next
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 2 Sep 2019 16:57:40 +0000 (09:57 -0700)]
Linux 5.3-rc7
Linus Torvalds [Mon, 2 Sep 2019 16:30:34 +0000 (09:30 -0700)]
Merge tag 'char-misc-5.3-rc7' of git://git./linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small char and misc driver fixes for reported issues for
5.3-rc7
Also included in here is the documentation for how we are handling
hardware issues under embargo that everyone has finally agreed on, as
well as a MAINTAINERS update for the suckers who agreed to handle the
LICENSES/ files.
All of these have been in linux-next last week with no reported
issues"
* tag 'char-misc-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
fsi: scom: Don't abort operations for minor errors
vmw_balloon: Fix offline page marking with compaction
VMCI: Release resource if the work is already queued
Documentation/process: Embargoed hardware security issues
lkdtm/bugs: fix build error in lkdtm_EXHAUST_STACK
mei: me: add Tiger Lake point LP device ID
intel_th: pci: Add Tiger Lake support
intel_th: pci: Add support for another Lewisburg PCH
stm class: Fix a double free of stm_source_device
MAINTAINERS: add entry for LICENSES and SPDX stuff
fpga: altera-ps-spi: Fix getting of optional confd gpio
Linus Torvalds [Mon, 2 Sep 2019 16:15:30 +0000 (09:15 -0700)]
Merge tag 'usb-5.3-rc7' of git://git./linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes that have been in linux-next this past
week for 5.3-rc7
They fix the usual xhci, syzbot reports, and other small issues that
have come up last week.
All have been in linux-next with no reported issues"
* tag 'usb-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: cdc-wdm: fix race between write and disconnect due to flag abuse
usb: host: xhci: rcar: Fix typo in compatible string matching
usb: host: xhci-tegra: Set DMA mask correctly
USB: storage: ums-realtek: Whitelist auto-delink support
USB: storage: ums-realtek: Update module parameter description for auto_delink_en
usb: host: ohci: fix a race condition between shutdown and irq
usb: hcd: use managed device resources
typec: tcpm: fix a typo in the comparison of pdo_max_voltage
usb-storage: Add new JMS567 revision to unusual_devs
usb: chipidea: udc: don't do hardware access if gadget has stopped
usbtmc: more sanity checking for packet size
usb: udc: lpc32xx: silence fall-through warning
Linus Torvalds [Mon, 2 Sep 2019 01:45:28 +0000 (18:45 -0700)]
Merge git://git./linux/kernel/git/netdev/net
Pull networking fixes from David Miller:
1) Fix some length checks during OGM processing in batman-adv, from
Sven Eckelmann.
2) Fix regression that caused netfilter conntrack sysctls to not be
per-netns any more. From Florian Westphal.
3) Use after free in netpoll, from Feng Sun.
4) Guard destruction of pfifo_fast per-cpu qdisc stats with
qdisc_is_percpu_stats(), from Davide Caratti. Similar bug is fixed
in pfifo_fast_enqueue().
5) Fix memory leak in mld_del_delrec(), from Eric Dumazet.
6) Handle neigh events on internal ports correctly in nfp, from John
Hurley.
7) Clear SKB timestamp in NF flow table code so that it does not
confuse fq scheduler. From Florian Westphal.
8) taprio destroy can crash if it is invoked in a failure path of
taprio_init(), because the list head isn't setup properly yet and
the list del is unconditional. Perform the list add earlier to
address this. From Vladimir Oltean.
9) Make sure to reapply vlan filters on device up, in aquantia driver.
From Dmitry Bogdanov.
10) sgiseeq driver releases DMA memory using free_page() instead of
dma_free_attrs(). From Christophe JAILLET.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (58 commits)
net: seeq: Fix the function used to release some memory in an error handling path
enetc: Add missing call to 'pci_free_irq_vectors()' in probe and remove functions
net: bcmgenet: use ethtool_op_get_ts_info()
tc-testing: don't hardcode 'ip' in nsPlugin.py
net: dsa: microchip: add KSZ8563 compatibility string
dt-bindings: net: dsa: document additional Microchip KSZ8563 switch
net: aquantia: fix out of memory condition on rx side
net: aquantia: linkstate irq should be oneshot
net: aquantia: reapply vlan filters on up
net: aquantia: fix limit of vlan filters
net: aquantia: fix removal of vlan 0
net/sched: cbs: Set default link speed to 10 Mbps in cbs_set_port_rate
taprio: Set default link speed to 10 Mbps in taprio_set_picos_per_byte
taprio: Fix kernel panic in taprio_destroy
net: dsa: microchip: fill regmap_config name
rxrpc: Fix lack of conn cleanup when local endpoint is cleaned up [ver #2]
net: stmmac: dwmac-rk: Don't fail if phy regulator is absent
amd-xgbe: Fix error path in xgbe_mod_init()
netfilter: nft_meta_bridge: Fix get NFT_META_BRI_IIFVPROTO in network byteorder
mac80211: Correctly set noencrypt for PAE frames
...
David S. Miller [Sun, 1 Sep 2019 19:16:38 +0000 (12:16 -0700)]
Merge branch 'net-dsa-mv88e6xxx-centralize-SERDES-IRQ-handling'
Vivien Didelot says:
====================
net: dsa: mv88e6xxx: centralize SERDES IRQ handling
Following Marek's work on the abstraction of the SERDES lanes mapping, this
series trades the .serdes_irq_setup and .serdes_irq_free callbacks for new
.serdes_irq_mapping, .serdes_irq_enable and .serdes_irq_status operations.
This has the benefit to limit the various SERDES implementations to simple
register accesses only; centralize the IRQ handling and mutex locking logic;
as well as reducing boilerplate in the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sat, 31 Aug 2019 20:18:36 +0000 (16:18 -0400)]
net: dsa: mv88e6xxx: centralize SERDES IRQ handling
The .serdes_irq_setup are all following the same steps: get the SERDES
lane, get the IRQ mapping, request the IRQ, then enable it. So do
the .serdes_irq_free implementations: get the SERDES lane, disable
the IRQ, then free it.
This patch removes these operations in favor of generic functions.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sat, 31 Aug 2019 20:18:35 +0000 (16:18 -0400)]
net: dsa: mv88e6xxx: introduce .serdes_irq_status
Introduce a new .serdes_irq_status operation to prepare the abstraction
of IRQ thread from the SERDES IRQ setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sat, 31 Aug 2019 20:18:34 +0000 (16:18 -0400)]
net: dsa: mv88e6xxx: introduce .serdes_irq_enable
Introduce a new .serdes_irq_enable operation to prepare the abstraction
of IRQ enabling from the SERDES IRQ setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sat, 31 Aug 2019 20:18:33 +0000 (16:18 -0400)]
net: dsa: mv88e6xxx: pass lane to .serdes_power
Now the first step of all .serdes_power implementations is getting
the lane mapping. Since we have an operation for that, call it in
the wrapper and pass the lane down to the .serdes_power operation.
This also allows to avoid querying the SERDES lane twice in
mv88e6xxx_port_set_cmode.
At the same time provide mv88e6xxx_serdes_power_{up,down} helpers
and prefer up/down instead of on/off as in the documentation.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sat, 31 Aug 2019 20:18:32 +0000 (16:18 -0400)]
net: dsa: mv88e6xxx: merge mv88e6352_serdes_power_set
The mv88e6352_serdes_power_set helper is only used at one place, in
mv88e6352_serdes_power. Keep it simple and merge the two functions
together.
Use mv88e6xxx_serdes_get_lane instead of mv88e6352_port_has_serdes
to avoid moving code. No functional changes.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sat, 31 Aug 2019 20:18:31 +0000 (16:18 -0400)]
net: dsa: mv88e6xxx: implement mv88e6352_serdes_get_lane
Even though 88E6352 has no dedicated lane for SERDES interfaces, it
uses a similar code as the other .serdes_get_lane implementations to
check the port's CMODE and ensure that SERDES operations are doable.
For consistency, implement mv88e6352_serdes_get_lane for the 88E6352
and similar switches which simply returns an unused 0xff lane address.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sat, 31 Aug 2019 20:18:30 +0000 (16:18 -0400)]
net: dsa: mv88e6xxx: simplify .serdes_get_lane
Because the mapping between a SERDES interface and its lane is static,
we don't need to stick with negative error codes actually and we can
simply return 0 if there is no lane, just like the IRQ mapping.
This way we can keep a simple and intuitive API using unsigned lane
numbers while simplifying the implementations with single return
statements. Last but not least, fix the reverse chrismas tree in
mv88e6390x_serdes_get_lane.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sat, 31 Aug 2019 20:18:29 +0000 (16:18 -0400)]
net: dsa: mv88e6xxx: introduce .serdes_irq_mapping
Introduce a new .serdes_irq_mapping operation to prepare the
abstraction of IRQ mapping from the SERDES IRQ setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sat, 31 Aug 2019 20:18:28 +0000 (16:18 -0400)]
net: dsa: mv88e6xxx: fix SERDES IRQ mapping
The current mv88e6xxx SERDES code checks for negative error code from
irq_find_mapping, while this function returns an unsigned integer. This
patch removes this dead code and simply returns 0 is no IRQ is found.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sat, 31 Aug 2019 20:18:27 +0000 (16:18 -0400)]
net: dsa: mv88e6xxx: check errors in mv88e6352_serdes_irq_link
The mv88e6352_serdes_irq_link helper is not checking for any error that
may occur during hardware accesses. Worst, the "up" boolean is set from
the potentially unused "status" variable, if read operations failed.
As done in mv88e6390_serdes_irq_link_sgmii, return right away and do
not call dsa_port_phylink_mac_change if an error occurred.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Sat, 31 Aug 2019 12:29:11 +0000 (12:29 +0000)]
net: hns3: remove set but not used variable 'qos'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c: In function 'hclge_restore_vlan_table':
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c:8016:18: warning:
variable 'qos' set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes:
70a214903da9 ("net: hns3: reduce the parameters of some functions")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Sat, 31 Aug 2019 07:29:49 +0000 (08:29 +0100)]
net: hns3: remove redundant assignment to pointer reg_info
Pointer reg_info is being initialized with a value that is never read and
is being re-assigned a little later on. The assignment is redundant
and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Sat, 31 Aug 2019 07:17:51 +0000 (09:17 +0200)]
net: seeq: Fix the function used to release some memory in an error handling path
In commit
99cd149efe82 ("sgiseeq: replace use of dma_cache_wback_inv"),
a call to 'get_zeroed_page()' has been turned into a call to
'dma_alloc_coherent()'. Only the remove function has been updated to turn
the corresponding 'free_page()' into 'dma_free_attrs()'.
The error hndling path of the probe function has not been updated.
Fix it now.
Rename the corresponding label to something more in line.
Fixes:
99cd149efe82 ("sgiseeq: replace use of dma_cache_wback_inv")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Sun, 1 Sep 2019 15:52:05 +0000 (16:52 +0100)]
netlabel: remove redundant assignment to pointer iter
Pointer iter is being initialized with a value that is never read and
is being re-assigned a little later on. The assignment is redundant
and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Sun, 1 Sep 2019 08:42:44 +0000 (10:42 +0200)]
r8169: don't set bit RxVlan on RTL8125
RTL8125 uses a different register for VLAN offloading config,
therefore don't set bit RxVlan.
Fixes:
f1bce4ad2f1c ("r8169: add support for RTL8125")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 1 Sep 2019 18:21:57 +0000 (11:21 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of fixes for x86:
- Fix the bogus detection of 32bit user mode for uretprobes which
caused corruption of the user return address resulting in
application crashes. In the uprobes handler in_ia32_syscall() is
obviously always returning false on a 64bit kernel. Use
user_64bit_mode() instead which works correctly.
- Prevent large page splitting when ftrace flips RW/RO on the kernel
text which caused iTLB performance issues. Ftrace wants to be
converted to text_poke() which avoids the problem, but for now
allow large page preservation in the static protections check when
the change request spawns a full large page.
- Prevent arch_dynirq_lower_bound() from returning 0 when the IOAPIC
is configured via device tree. In the device tree case the GSI 1:1
mapping is meaningless therefore the lower bound which protects the
GSI range on ACPI machines is irrelevant. Return the lower bound
which the core hands to the function instead of blindly returning 0
which causes the core to allocate the invalid virtual interupt
number 0 which in turn prevents all drivers from allocating and
requesting an interrupt.
- Remove the bogus initialization of LDR and DFR in the 32bit bigsmp
APIC driver. That uses physical destination mode where LDR/DFR are
ignored, but the initialization and the missing clear of LDR caused
the APIC to be left in a inconsistent state on kexec/reboot.
- Clear LDR when clearing the APIC registers so the APIC is in a well
defined state.
- Initialize variables proper in the find_trampoline_placement()
code.
- Silence GCC( build warning for the real mode part of the build"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm/cpa: Prevent large page split when ftrace flips RW on kernel text
x86/build: Add -Wnoaddress-of-packed-member to REALMODE_CFLAGS, to silence GCC9 build warning
x86/boot/compressed/64: Fix missing initialization in find_trampoline_placement()
x86/apic: Include the LDR when clearing out APIC registers
x86/apic: Do not initialize LDR and DFR for bigsmp
uprobes/x86: Fix detection of 32-bit user mode
x86/apic: Fix arch_dynirq_lower_bound() bug for DT enabled machines
Linus Torvalds [Sun, 1 Sep 2019 18:09:42 +0000 (11:09 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
"Two fixes for perf x86 hardware implementations:
- Restrict the period on Nehalem machines to prevent perf from
hogging the CPU
- Prevent the AMD IBS driver from overwriting the hardwre controlled
and pre-seeded reserved bits (0-6) in the count register which
caused a sample bias for dispatched micro-ops"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/amd/ibs: Fix sample bias for dispatched micro-ops
perf/x86/intel: Restrict period on Nehalem
Linus Torvalds [Sun, 1 Sep 2019 17:39:25 +0000 (10:39 -0700)]
Merge branch 'turbostat' of git://git./linux/kernel/git/lenb/linux
Pull turbostat updates from Len Brown:
"User-space turbostat (and x86_energy_perf_policy) patches.
They are primarily bug fixes from users"
* 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: update version number
tools/power turbostat: Add support for Hygon Fam 18h (Dhyana) RAPL
tools/power turbostat: Fix caller parameter of get_tdp_amd()
tools/power turbostat: Fix CPU%C1 display value
tools/power turbostat: do not enforce 1ms
tools/power turbostat: read from pipes too
tools/power turbostat: Add Ice Lake NNPI support
tools/power turbostat: rename has_hsw_msrs()
tools/power turbostat: Fix Haswell Core systems
tools/power turbostat: add Jacobsville support
tools/power turbostat: fix buffer overrun
tools/power turbostat: fix file descriptor leaks
tools/power turbostat: fix leak of file descriptor on error return path
tools/power turbostat: Make interval calculation per thread to reduce jitter
tools/power turbostat: remove duplicate pc10 column
tools/power x86_energy_perf_policy: Fix argument parsing
tools/power: Fix typo in man page
tools/power/x86: Enable compiler optimisations and Fortify by default
tools/power x86_energy_perf_policy: Fix "uninitialized variable" warnings at -O2
Ben Wei [Fri, 30 Aug 2019 20:50:51 +0000 (20:50 +0000)]
net/ncsi: add response handlers for PLDM over NC-SI
This patch adds handlers for PLDM over NC-SI command response.
This enables NC-SI driver recognizes the packet type so the responses
don't get dropped as unknown packet type.
PLDM over NC-SI are not handled in kernel driver for now, but can be
passed back to user space via Netlink for further handling.
Signed-off-by: Ben Wei <benwei@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Fri, 30 Aug 2019 20:23:12 +0000 (22:23 +0200)]
enetc: Add missing call to 'pci_free_irq_vectors()' in probe and remove functions
Call to 'pci_free_irq_vectors()' are missing both in the error handling
path of the probe function, and in the remove function.
Add them.
Fixes:
19971f5ea0ab ("enetc: add PTP clock driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ryan M. Collins [Fri, 30 Aug 2019 18:49:55 +0000 (14:49 -0400)]
net: bcmgenet: use ethtool_op_get_ts_info()
This change enables the use of SW timestamping on the Raspberry Pi 4.
bcmgenet's transmit function bcmgenet_xmit() implements software
timestamping. However the SOF_TIMESTAMPING_TX_SOFTWARE capability was
missing and only SOF_TIMESTAMPING_RX_SOFTWARE was announced. By using
ethtool_ops bcmgenet_ethtool_ops() as get_ts_info(), the
SOF_TIMESTAMPING_TX_SOFTWARE capability is announced.
Similar to commit
a8f5cb9e7991 ("smsc95xx: use ethtool_op_get_ts_info()")
Signed-off-by: Ryan M. Collins <rmc032@bucknell.edu>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Fri, 30 Aug 2019 16:51:47 +0000 (18:51 +0200)]
tc-testing: don't hardcode 'ip' in nsPlugin.py
the following tdc test fails on Fedora:
# ./tdc.py -e 2638
-- ns/SubPlugin.__init__
Test 2638: Add matchall and try to get it
-----> prepare stage *** Could not execute: "$TC qdisc add dev $DEV1 clsact"
-----> prepare stage *** Error message: "/bin/sh: ip: command not found"
returncode 127; expected [0]
-----> prepare stage *** Aborting test run.
Let nsPlugin.py use the 'IP' variable introduced with commit
92c1a19e2fb9
("tc-tests: added path to ip command in tdc"), so that the path to 'ip' is
correctly resolved to the value we have in tdc_config.py.
# ./tdc.py -e 2638
-- ns/SubPlugin.__init__
Test 2638: Add matchall and try to get it
All test results:
1..1
ok 1 2638 - Add matchall and try to get it
Fixes:
489ce2f42514 ("tc-testing: Restore original behaviour for namespaces in tdc")
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 1 Sep 2019 06:46:13 +0000 (23:46 -0700)]
Merge branch 'Minor-cleanup-in-devlink'
Parav Pandit says:
====================
Minor cleanup in devlink
Two minor cleanup in devlink.
Patch-1 Explicitly defines devlink port index as unsigned int
Patch-2 Uses switch-case to handle different port flavours attributes
====================
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parav Pandit [Fri, 30 Aug 2019 10:39:45 +0000 (05:39 -0500)]
devlink: Use switch-case instead of if-else
Make core more readable with switch-case for various port flavours.
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parav Pandit [Fri, 30 Aug 2019 10:39:44 +0000 (05:39 -0500)]
devlink: Make port index data type as unsigned int
Devlink port index attribute is returned to users as u32 through
netlink response.
Change index data type from 'unsigned' to 'unsigned int' to avoid
below checkpatch.pl warning.
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
81: FILE: include/net/devlink.h:81:
+ unsigned index;
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 1 Sep 2019 06:44:28 +0000 (23:44 -0700)]
Merge branch 'net-tls-add-socket-diag'
Davide Caratti says:
====================
net: tls: add socket diag
The current kernel does not provide any diagnostic tool, except
getsockopt(TCP_ULP), to know more about TCP sockets that have an upper
layer protocol (ULP) on top of them. This series extends the set of
information exported by INET_DIAG_INFO, to include data that are
specific to the ULP (and that might be meaningful for debug/testing
purposes).
patch 1/3 ensures that the control plane reads/updates ULP specific data
using RCU.
patch 2/3 extends INET_DIAG_INFO and allows knowing the ULP name for
each TCP socket that has done setsockopt(TCP_ULP) successfully.
patch 3/3 extends kTLS to let programs like 'ss' know the protocol
version and the cipher in use.
Changes since v2:
- remove unneeded #ifdef and fix reverse christmas tree in
tls_get_info(), thanks to Jakub Kicinski
Changes since v1:
- don't worry about grace period when accessing ulp_ops, thanks to
Jakub Kicinski and Eric Dumazet
- use rcu_dereference() to access ULP data in tls get_info(), and
test against NULL value, thanks to Jakub Kicinski
- move RCU protected section inside tls get_info(), thanks to Jakub
Kicinski
Changes since RFC:
- some coding style fixes, thanks to Jakub Kicinski
- add X_UNSPEC as lowest value of uAPI enums, thanks to Jakub Kicinski
- fix assignment of struct nlattr *start, thanks to Jakub Kicinski
- let tls dump RXCONF and TXCONF, suggested by Jakub Kicinski
- don't dump anything if TLS version or cipher are 0 (but still return a
constant size in get_aux_size()), thanks to Boris Pismenny
- constify first argument of get_info() and get_size()
- use RCU to access access ulp_ops, like it's done for ca_ops
- add patch 1/3, from Jakub Kicinski
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Fri, 30 Aug 2019 10:25:49 +0000 (12:25 +0200)]
net: tls: export protocol version, cipher, tx_conf/rx_conf to socket diag
When an application configures kernel TLS on top of a TCP socket, it's
now possible for inet_diag_handler() to collect information regarding the
protocol version, the cipher type and TX / RX configuration, in case
INET_DIAG_INFO is requested.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Fri, 30 Aug 2019 10:25:48 +0000 (12:25 +0200)]
tcp: ulp: add functions to dump ulp-specific information
currently, only getsockopt(TCP_ULP) can be invoked to know if a ULP is on
top of a TCP socket. Extend idiag_get_aux() and idiag_get_aux_size(),
introduced by commit
b37e88407c1d ("inet_diag: allow protocols to provide
additional data"), to report the ULP name and other information that can
be made available by the ULP through optional functions.
Users having CAP_NET_ADMIN privileges will then be able to retrieve this
information through inet_diag_handler, if they specify INET_DIAG_INFO in
the request.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Fri, 30 Aug 2019 10:25:47 +0000 (12:25 +0200)]
net/tls: use RCU protection on icsk->icsk_ulp_data
We need to make sure context does not get freed while diag
code is interrogating it. Free struct tls_context with
kfree_rcu().
We add the __rcu annotation directly in icsk, and cast it
away in the datapath accessor. Presumably all ULPs will
do a similar thing.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 1 Sep 2019 06:36:37 +0000 (23:36 -0700)]
Merge branch 'net-dsa-microchip-add-KSZ8563-support'
Razvan Stefanescu says:
====================
net: dsa: microchip: add KSZ8563 support
This patchset adds compatibility string for the KSZ8563 switch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Razvan Stefanescu [Fri, 30 Aug 2019 07:52:02 +0000 (10:52 +0300)]
net: dsa: microchip: add KSZ8563 compatibility string
It is a 3-Port 10/100 Ethernet Switch with 1588v2 PTP.
Signed-off-by: Razvan Stefanescu <razvan.stefanescu@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Razvan Stefanescu [Fri, 30 Aug 2019 07:52:01 +0000 (10:52 +0300)]
dt-bindings: net: dsa: document additional Microchip KSZ8563 switch
It is a 3-Port 10/100 Ethernet Switch with 1588v2 PTP.
Signed-off-by: Razvan Stefanescu <razvan.stefanescu@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 1 Sep 2019 02:07:17 +0000 (19:07 -0700)]
Merge branch 'net-aquantia-fixes-on-vlan-filters-and-other-conditions'
Igor Russkikh says:
====================
net: aquantia: fixes on vlan filters and other conditions
Here is a set of various bug fixes related to vlan filter offload and
two other rare cases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Bogdanov [Fri, 30 Aug 2019 12:08:38 +0000 (12:08 +0000)]
net: aquantia: fix out of memory condition on rx side
On embedded environments with hard memory limits it is a normal although
rare case when skb can't be allocated on rx part under high traffic.
In such OOM cases napi_complete_done() was not called.
So the napi object became in an invalid state like it is "scheduled".
Kernel do not re-schedules the poll of that napi object.
Consequently, kernel can not remove that object the system hangs on
`ifconfig down` waiting for a poll.
We are fixing this by gracefully closing napi poll routine with correct
invocation of napi_complete_done.
This was reproduced with artificially failing the allocation of skb to
simulate an "out of memory" error case and check that traffic does
not get stuck.
Fixes:
970a2e9864b0 ("net: ethernet: aquantia: Vector operations")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Fri, 30 Aug 2019 12:08:36 +0000 (12:08 +0000)]
net: aquantia: linkstate irq should be oneshot
Declaring threaded irq handler should also indicate the irq is
oneshot. It is oneshot indeed, because HW implements irq automasking
on trigger.
Not declaring this causes some kernel configurations to fail
on interface up, because request_threaded_irq returned an err code.
The issue was originally hidden on normal x86_64 configuration with
latest kernel, because depending on interrupt controller, irq driver
added ONESHOT flag on its own.
Issue was observed on older kernels (4.14) where no such logic exists.
Fixes:
4c83f170b3ac ("net: aquantia: link status irq handling")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reported-by: Michael Symolkin <Michael.Symolkin@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Bogdanov [Fri, 30 Aug 2019 12:08:35 +0000 (12:08 +0000)]
net: aquantia: reapply vlan filters on up
In case of device reconfiguration the driver may reset the device invisible
for other modules, vlan module in particular. So vlans will not be
removed&created and vlan filters will not be configured in the device.
The patch reapplies the vlan filters at device start.
Fixes:
7975d2aff5afb ("net: aquantia: add support of rx-vlan-filter offload")
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Bogdanov [Fri, 30 Aug 2019 12:08:33 +0000 (12:08 +0000)]
net: aquantia: fix limit of vlan filters
Fix a limit condition of vlans on the interface before setting vlan
promiscuous mode
Fixes:
48dd73d08d4dd ("net: aquantia: fix vlans not working over bridged network")
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Bogdanov [Fri, 30 Aug 2019 12:08:30 +0000 (12:08 +0000)]
net: aquantia: fix removal of vlan 0
Due to absence of checking against the rx flow rule when vlan 0 is being
removed, the other rule could be removed instead of the rule with vlan 0
Fixes:
7975d2aff5afb ("net: aquantia: add support of rx-vlan-filter offload")
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 1 Sep 2019 01:45:35 +0000 (18:45 -0700)]
Merge branch 'Fix-issues-in-tc-taprio-and-tc-cbs'
Vladimir Oltean says:
====================
Fix issues in tc-taprio and tc-cbs
This series fixes one panic and one WARN_ON found in the tc-taprio
qdisc, while trying to apply it:
- On an interface which is not multi-queue
- On an interface which has no carrier
The tc-cbs was also visually found to suffer of the same issue as
tc-taprio, and the fix was only compile-tested in that case.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 30 Aug 2019 01:07:23 +0000 (04:07 +0300)]
net/sched: cbs: Set default link speed to 10 Mbps in cbs_set_port_rate
The discussion to be made is absolutely the same as in the case of
previous patch ("taprio: Set default link speed to 10 Mbps in
taprio_set_picos_per_byte"). Nothing is lost when setting a default.
Cc: Leandro Dorileo <leandro.maciel.dorileo@intel.com>
Fixes:
e0a7683d30e9 ("net/sched: cbs: fix port_rate miscalculation")
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 30 Aug 2019 01:07:22 +0000 (04:07 +0300)]
taprio: Set default link speed to 10 Mbps in taprio_set_picos_per_byte
The taprio budget needs to be adapted at runtime according to interface
link speed. But that handling is problematic.
For one thing, installing a qdisc on an interface that doesn't have
carrier is not illegal. But taprio prints the following stack trace:
[ 31.851373] ------------[ cut here ]------------
[ 31.856024] WARNING: CPU: 1 PID: 207 at net/sched/sch_taprio.c:481 taprio_dequeue+0x1a8/0x2d4
[ 31.864566] taprio: dequeue() called with unknown picos per byte.
[ 31.864570] Modules linked in:
[ 31.873701] CPU: 1 PID: 207 Comm: tc Not tainted 5.3.0-rc5-01199-g8838fe023cd6 #1689
[ 31.881398] Hardware name: Freescale LS1021A
[ 31.885661] [<
c03133a4>] (unwind_backtrace) from [<
c030d8cc>] (show_stack+0x10/0x14)
[ 31.893368] [<
c030d8cc>] (show_stack) from [<
c10ac958>] (dump_stack+0xb4/0xc8)
[ 31.900555] [<
c10ac958>] (dump_stack) from [<
c0349d04>] (__warn+0xe0/0xf8)
[ 31.907395] [<
c0349d04>] (__warn) from [<
c0349d64>] (warn_slowpath_fmt+0x48/0x6c)
[ 31.914841] [<
c0349d64>] (warn_slowpath_fmt) from [<
c0f38db4>] (taprio_dequeue+0x1a8/0x2d4)
[ 31.923150] [<
c0f38db4>] (taprio_dequeue) from [<
c0f227b0>] (__qdisc_run+0x90/0x61c)
[ 31.930856] [<
c0f227b0>] (__qdisc_run) from [<
c0ec82ac>] (net_tx_action+0x12c/0x2bc)
[ 31.938560] [<
c0ec82ac>] (net_tx_action) from [<
c0302298>] (__do_softirq+0x130/0x3c8)
[ 31.946350] [<
c0302298>] (__do_softirq) from [<
c03502a0>] (irq_exit+0xbc/0xd8)
[ 31.953536] [<
c03502a0>] (irq_exit) from [<
c03a4808>] (__handle_domain_irq+0x60/0xb4)
[ 31.961328] [<
c03a4808>] (__handle_domain_irq) from [<
c0754478>] (gic_handle_irq+0x58/0x9c)
[ 31.969638] [<
c0754478>] (gic_handle_irq) from [<
c0301a8c>] (__irq_svc+0x6c/0x90)
[ 31.977076] Exception stack(0xe8167b20 to 0xe8167b68)
[ 31.982100] 7b20:
e9d4bd80 00000cc0 000000cf 00000000 e9d4bd80 c1f38958 00000cc0 c1f38960
[ 31.990234] 7b40:
00000001 000000cf 00000004 e9dc0800 00000000 e8167b70 c0f478ec c0f46d94
[ 31.998363] 7b60:
60070013 ffffffff
[ 32.001833] [<
c0301a8c>] (__irq_svc) from [<
c0f46d94>] (netlink_trim+0x18/0xd8)
[ 32.009104] [<
c0f46d94>] (netlink_trim) from [<
c0f478ec>] (netlink_broadcast_filtered+0x34/0x414)
[ 32.017930] [<
c0f478ec>] (netlink_broadcast_filtered) from [<
c0f47cec>] (netlink_broadcast+0x20/0x28)
[ 32.027102] [<
c0f47cec>] (netlink_broadcast) from [<
c0eea378>] (rtnetlink_send+0x34/0x88)
[ 32.035238] [<
c0eea378>] (rtnetlink_send) from [<
c0f25890>] (notify_and_destroy+0x2c/0x44)
[ 32.043461] [<
c0f25890>] (notify_and_destroy) from [<
c0f25e08>] (qdisc_graft+0x398/0x470)
[ 32.051595] [<
c0f25e08>] (qdisc_graft) from [<
c0f27a00>] (tc_modify_qdisc+0x3a4/0x724)
[ 32.059470] [<
c0f27a00>] (tc_modify_qdisc) from [<
c0ee4c84>] (rtnetlink_rcv_msg+0x260/0x2ec)
[ 32.067864] [<
c0ee4c84>] (rtnetlink_rcv_msg) from [<
c0f4a988>] (netlink_rcv_skb+0xb8/0x110)
[ 32.076172] [<
c0f4a988>] (netlink_rcv_skb) from [<
c0f4a170>] (netlink_unicast+0x1b4/0x22c)
[ 32.084392] [<
c0f4a170>] (netlink_unicast) from [<
c0f4a5e4>] (netlink_sendmsg+0x33c/0x380)
[ 32.092614] [<
c0f4a5e4>] (netlink_sendmsg) from [<
c0ea9f40>] (sock_sendmsg+0x14/0x24)
[ 32.100403] [<
c0ea9f40>] (sock_sendmsg) from [<
c0eaa780>] (___sys_sendmsg+0x214/0x228)
[ 32.108279] [<
c0eaa780>] (___sys_sendmsg) from [<
c0eabad0>] (__sys_sendmsg+0x50/0x8c)
[ 32.116068] [<
c0eabad0>] (__sys_sendmsg) from [<
c0301000>] (ret_fast_syscall+0x0/0x54)
[ 32.123938] Exception stack(0xe8167fa8 to 0xe8167ff0)
[ 32.128960] 7fa0:
b6fa68c8 000000f8 00000003 bea142d0 00000000 00000000
[ 32.137093] 7fc0:
b6fa68c8 000000f8 0052154c 00000128 5d6468a2 00000000 00000028 00558c9c
[ 32.145224] 7fe0:
00000070 bea14278 00530d64 b6e17e64
[ 32.150659] ---[ end trace
2139c9827c3e5177 ]---
This happens because the qdisc ->dequeue callback gets called. Which
again is not illegal, the qdisc will dequeue even when the interface is
up but doesn't have carrier (and hence SPEED_UNKNOWN), and the frames
will be dropped further down the stack in dev_direct_xmit().
And, at the end of the day, for what? For calculating the initial budget
of an interface which is non-operational at the moment and where frames
will get dropped anyway.
So if we can't figure out the link speed, default to SPEED_10 and move
along. We can also remove the runtime check now.
Cc: Leandro Dorileo <leandro.maciel.dorileo@intel.com>
Fixes:
7b9eba7ba0c1 ("net/sched: taprio: fix picos_per_byte miscalculation")
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 30 Aug 2019 01:07:21 +0000 (04:07 +0300)]
taprio: Fix kernel panic in taprio_destroy
taprio_init may fail earlier than this line:
list_add(&q->taprio_list, &taprio_list);
i.e. due to the net device not being multi queue.
Attempting to remove q from the global taprio_list when it is not part
of it will result in a kernel panic.
Fix it by matching list_add and list_del better to one another in the
order of operations. This way we can keep the deletion unconditional
and with lower complexity - O(1).
Cc: Leandro Dorileo <leandro.maciel.dorileo@intel.com>
Fixes:
7b9eba7ba0c1 ("net/sched: taprio: fix picos_per_byte miscalculation")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 31 Aug 2019 20:32:30 +0000 (13:32 -0700)]
Merge branch 'qed-Enhancements'
Sudarsana Reddy Kalluru says:
====================
qed*: Enhancements.
The patch series adds couple of enhancements to qed/qede drivers.
- Support for dumping the config id attributes via ethtool -w/W.
- Support for dumping the GRC data of required memory regions using
ethtool -w/W interfaces.
Patch (1) adds driver APIs for reading the config id attributes.
Patch (2) adds ethtool support for dumping the config id attributes.
Patch (3) adds support for configuring the GRC dump config flags.
Patch (4) adds ethtool support for dumping the grc dump.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudarsana Reddy Kalluru [Fri, 30 Aug 2019 07:42:06 +0000 (00:42 -0700)]
qede: Add support for dumping the grc data.
This patch adds driver support for configuring grc dump config flags, and
dumping the grc data via ethtool get/set-dump interfaces.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudarsana Reddy Kalluru [Fri, 30 Aug 2019 07:42:05 +0000 (00:42 -0700)]
qed: Add APIs for configuring grc dump config flags.
The patch adds driver support for configuring the grc dump config flags.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudarsana Reddy Kalluru [Fri, 30 Aug 2019 07:42:04 +0000 (00:42 -0700)]
qede: Add support for reading the config id attributes.
Add driver support for dumping the config id attributes via ethtool dump
interfaces.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudarsana Reddy Kalluru [Fri, 30 Aug 2019 07:42:03 +0000 (00:42 -0700)]
qed: Add APIs for reading config id attributes.
The patch adds driver support for reading the config id attributes from NVM
flash partition.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 31 Aug 2019 20:21:19 +0000 (13:21 -0700)]
Merge branch 'Dynamic-toggling-of-vlan_filtering-for-SJA1105-DSA'
Vladimir Oltean says:
====================
Dynamic toggling of vlan_filtering for SJA1105 DSA
This patchset addresses a limitation in dsa_8021q where this sequence of
commands was causing the switch to stop forwarding traffic:
ip link add name br0 type bridge vlan_filtering 0
ip link set dev swp2 master br0
echo 1 > /sys/class/net/br0/bridge/vlan_filtering
echo 0 > /sys/class/net/br0/bridge/vlan_filtering
The issue has to do with the VLAN table manipulations that dsa_8021q
does without notifying the bridge layer. The solution is to always
restore the VLANs that the bridge knows about, when disabling tagging.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 30 Aug 2019 00:53:25 +0000 (03:53 +0300)]
net: dsa: tag_8021q: Restore bridge VLANs when enabling vlan_filtering
The bridge core assumes that enabling/disabling vlan_filtering will
translate into the simple toggling of a flag for switchdev drivers.
That is clearly not the case for sja1105, which alters the VLAN table
and the pvids in order to obtain port separation in standalone mode.
There are 2 parts to the issue.
First, tag_8021q changes the pvid to a unique per-port rx_vid for frame
identification. But we need to disable tag_8021q when vlan_filtering
kicks in, and at that point, the VLAN configured as pvid will have to be
removed from the filtering table of the ports. With an invalid pvid, the
ports will drop all traffic. Since the bridge will not call any vlan
operation through switchdev after enabling vlan_filtering, we need to
ensure we're in a functional state ourselves. Hence read the pvid that
the bridge is aware of, and program that into our ports.
Secondly, tag_8021q uses the 1024-3071 range privately in
vlan_filtering=0 mode. Had the user installed one of these VLANs during
a previous vlan_filtering=1 session, then upon the next tag_8021q
cleanup for vlan_filtering to kick in again, VLANs in that range will
get deleted unconditionally, hence breaking user expectation. So when
deleting the VLANs, check if the bridge had knowledge about them, and if
it did, re-apply the settings. Wrap this logic inside a
dsa_8021q_vid_apply helper function to reduce code duplication.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 30 Aug 2019 00:53:24 +0000 (03:53 +0300)]
net: bridge: Populate the pvid flag in br_vlan_get_info
Currently this simplified code snippet fails:
br_vlan_get_pvid(netdev, &pvid);
br_vlan_get_info(netdev, pvid, &vinfo);
ASSERT(!(vinfo.flags & BRIDGE_VLAN_INFO_PVID));
It is intuitive that the pvid of a netdevice should have the
BRIDGE_VLAN_INFO_PVID flag set.
However I can't seem to pinpoint a commit where this behavior was
introduced. It seems like it's been like that since forever.
At a first glance it would make more sense to just handle the
BRIDGE_VLAN_INFO_PVID flag in __vlan_add_flags. However, as Nikolay
explains:
There are a few reasons why we don't do it, most importantly because
we need to have only one visible pvid at any single time, even if it's
stale - it must be just one. Right now that rule will not be violated
by this change, but people will try using this flag and could see two
pvids simultaneously. You can see that the pvid code is even using
memory barriers to propagate the new value faster and everywhere the
pvid is read only once. That is the reason the flag is set
dynamically when dumping entries, too. A second (weaker) argument
against would be given the above we don't want another way to do the
same thing, specifically if it can provide us with two pvids (e.g. if
walking the vlan list) or if it can provide us with a pvid different
from the one set in the vg. [Obviously, I'm talking about RCU
pvid/vlan use cases similar to the dumps. The locked cases are fine.
I would like to avoid explaining why this shouldn't be relied upon
without locking]
So instead of introducing the above change and making sure of the pvid
uniqueness under RCU, simply dynamically populate the pvid flag in
br_vlan_get_info().
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
George McCollister [Thu, 29 Aug 2019 14:14:41 +0000 (09:14 -0500)]
net: dsa: microchip: fill regmap_config name
Use the register value width as the regmap_config name to prevent the
following error when the second and third regmap_configs are
initialized.
"debugfs: Directory '${bus-id}' with parent 'regmap' already present!"
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 31 Aug 2019 20:16:07 +0000 (13:16 -0700)]
Merge tag 'batadv-net-for-davem-
20190830' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here are two batman-adv bugfixes:
- Fix OGM and OGMv2 header read boundary check,
by Sven Eckelmann (2 patches)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 31 Aug 2019 20:15:19 +0000 (13:15 -0700)]
Merge tag 'batadv-next-for-davem-
20190830' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This maintenance patchset includes the following patches:
- Add Sven to the MAINTAINERS file, by Simon Wunderlich
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Len Brown [Sat, 31 Aug 2019 18:40:39 +0000 (14:40 -0400)]
tools/power turbostat: update version number
Today is 19.08.31, at least in some parts of the world.
Signed-off-by: Len Brown <len.brown@intel.com>
Pu Wen [Sat, 31 Aug 2019 02:20:31 +0000 (10:20 +0800)]
tools/power turbostat: Add support for Hygon Fam 18h (Dhyana) RAPL
Commit
9392bd98bba760be96ee ("tools/power turbostat: Add support for AMD
Fam 17h (Zen) RAPL") and the commit
3316f99a9f1b68c578c5 ("tools/power
turbostat: Also read package power on AMD F17h (Zen)") add AMD Fam 17h
RAPL support.
Hygon Family 18h(Dhyana) support RAPL in bit 14 of CPUID 0x80000007 EDX,
and has MSRs RAPL_PWR_UNIT/CORE_ENERGY_STAT/PKG_ENERGY_STAT. So add Hygon
Dhyana Family 18h support for RAPL.
Already tested on Hygon multi-node systems and it shows correct per-core
energy usage and the total package power.
Signed-off-by: Pu Wen <puwen@hygon.cn>
Reviewed-by: Calvin Walton <calvin.walton@kepstin.ca>
Signed-off-by: Len Brown <len.brown@intel.com>
Pu Wen [Sat, 31 Aug 2019 02:19:58 +0000 (10:19 +0800)]
tools/power turbostat: Fix caller parameter of get_tdp_amd()
Commit
9392bd98bba760be96ee ("tools/power turbostat: Add support for AMD
Fam 17h (Zen) RAPL") add a function get_tdp_amd(), the parameter is CPU
family. But the rapl_probe_amd() function use wrong model parameter.
Fix the wrong caller parameter of get_tdp_amd() to use family.
Cc: <stable@vger.kernel.org> # v5.1+
Signed-off-by: Pu Wen <puwen@hygon.cn>
Reviewed-by: Calvin Walton <calvin.walton@kepstin.ca>
Signed-off-by: Len Brown <len.brown@intel.com>
Srinivas Pandruvada [Tue, 27 Aug 2019 17:57:14 +0000 (10:57 -0700)]
tools/power turbostat: Fix CPU%C1 display value
In some case C1% will be wrong value, when platform doesn't have MSR for
C1 residency.
For example:
Core CPU CPU%c1
- - 100.00
0 0 100.00
0 2 100.00
1 1 100.00
1 3 100.00
But adding Busy% will fix this
Core CPU Busy% CPU%c1
- - 99.77 0.23
0 0 99.77 0.23
0 2 99.77 0.23
1 1 99.77 0.23
1 3 99.77 0.23
This issue can be reproduced on most of the recent systems including
Broadwell, Skylake and later.
This is because if we don't select Busy% or Avg_MHz or Bzy_MHz then
mperf value will not be read from MSR, so it will be 0. But this
is required for C1% calculation when MSR for C1 residency is not present.
Same is true for C3, C6 and C7 column selection.
So add another define DO_BIC_READ(), which doesn't depend on user
column selection and use for mperf, C3, C6 and C7 related counters.
So when there is no platform support for C1 residency counters,
we still read these counters, if the CPU has support and user selected
display of CPU%c1.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Artem Bityutskiy [Wed, 14 Aug 2019 17:12:56 +0000 (20:12 +0300)]
tools/power turbostat: do not enforce 1ms
Turbostat works by taking a snapshot of counters, sleeping, taking another
snapshot, calculating deltas, and printing out the table.
The sleep time is controlled via -i option or by user sending a signal or a
character to stdin. In the latter case, turbostat always adds 1 ms
sleep before it reads the counters, in order to avoid larger imprecisions
in the results in prints.
While the 1 ms delay may be a good idea for a "dumb" user, it is a
problem for an "aware" user. I do thousands and thousands of measurements
over a short period of time (like 2ms), and turbostat unconditionally adds
a 1ms to my interval, so I cannot get what I really need.
This patch removes the unconditional 1ms sleep. This is an expert user
tool, after all, and non-experts will unlikely ever use it in the non-fixed
interval mode anyway, so I think it is OK to remove the 1ms delay.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Artem Bityutskiy [Wed, 14 Aug 2019 17:12:55 +0000 (20:12 +0300)]
tools/power turbostat: read from pipes too
Commit '
47936f944e78 tools/power turbostat: fix printing on input' make
a valid fix, but it completely disabled piped stdin support, which is
a valuable use-case. Indeed, if stdin is a pipe, turbostat won't read
anything from it, so it becomes impossible to get turbostat output at
user-defined moments, instead of the regular intervals.
There is no reason why this should works for terminals, but not for
pipes. This patch improves the situation. Instead of ignoring pipes, we
read data from them but gracefully handle the EOF case.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Rajneesh Bhardwaj [Fri, 14 Jun 2019 07:39:46 +0000 (13:09 +0530)]
tools/power turbostat: Add Ice Lake NNPI support
This enables turbostat utility on Ice Lake NNPI SoC.
Link: https://lkml.org/lkml/2019/6/5/1034
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Len Brown [Sat, 31 Aug 2019 18:16:07 +0000 (14:16 -0400)]
tools/power turbostat: rename has_hsw_msrs()
Perhaps if this more descriptive name had been used,
then we wouldn't have had the HSW ULT vs HSW CORE bug,
fixed by the previous commit.
Signed-off-by: Len Brown <len.brown@intel.com>
Len Brown [Sat, 31 Aug 2019 18:09:29 +0000 (14:09 -0400)]
tools/power turbostat: Fix Haswell Core systems
turbostat: cpu0: msr offset 0x630 read failed: Input/output error
because Haswell Core does not have C8-C10.
Output C8-C10 only on Haswell ULT.
Fixes:
f5a4c76ad7de ("tools/power turbostat: consolidate duplicate model numbers")
Reported-by: Prarit Bhargava <prarit@redhat.com>
Suggested-by: Kosuke Tatsukawa <tatsu@ab.jp.nec.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Zhang Rui [Sun, 21 Apr 2019 08:30:22 +0000 (16:30 +0800)]
tools/power turbostat: add Jacobsville support
Jacobsville behaves like Denverton.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Naoya Horiguchi [Wed, 3 Apr 2019 07:02:14 +0000 (16:02 +0900)]
tools/power turbostat: fix buffer overrun
turbostat could be terminated by general protection fault on some latest
hardwares which (for example) support 9 levels of C-states and show 18
"tADDED" lines. That bloats the total output and finally causes buffer
overrun. So let's extend the buffer to avoid this.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Gustavo A. R. Silva [Mon, 8 Apr 2019 16:12:40 +0000 (11:12 -0500)]
tools/power turbostat: fix file descriptor leaks
Fix file descriptor leaks by closing fp before return.
Addresses-Coverity-ID: 1444591 ("Resource leak")
Addresses-Coverity-ID: 1444592 ("Resource leak")
Fixes:
5ea7647b333f ("tools/power turbostat: Warn on bad ACPI LPIT data")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Colin Ian King [Mon, 8 Apr 2019 09:00:44 +0000 (10:00 +0100)]
tools/power turbostat: fix leak of file descriptor on error return path
Currently the error return path does not close the file fp and leaks
a file descriptor. Fix this by closing the file.
Fixes:
5ea7647b333f ("tools/power turbostat: Warn on bad ACPI LPIT data")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Yazen Ghannam [Mon, 25 Mar 2019 17:32:42 +0000 (17:32 +0000)]
tools/power turbostat: Make interval calculation per thread to reduce jitter
Turbostat currently normalizes TSC and other values by dividing by an
interval. This interval is the delta between the start of one global
(all counters on all CPUs) sampling and the start of another. However,
this introduces a lot of jitter into the data.
In order to reduce jitter, the interval calculation should be based on
timestamps taken per thread and close to the start of the thread's
sampling.
Define a per thread time value to hold the delta between samples taken
on the thread.
Use the timestamp taken at the beginning of sampling to calculate the
delta.
Move the thread's beginning timestamp to after the CPU migration to
avoid jitter due to the migration.
Use the global time delta for the average time delta.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Len Brown [Sat, 31 Aug 2019 16:30:24 +0000 (12:30 -0400)]
tools/power turbostat: remove duplicate pc10 column
Remove the duplicate pc10 column.
Fixes:
be0e54c4ebbf ("turbostat: Build-in "Low Power Idle" counters support")
Reported-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Zephaniah E. Loss-Cutler-Hull [Sat, 9 Feb 2019 13:25:48 +0000 (05:25 -0800)]
tools/power x86_energy_perf_policy: Fix argument parsing
The -w argument in x86_energy_perf_policy currently triggers an
unconditional segfault.
This is because the argument string reads: "+a:c:dD:E:e:f:m:M:rt:u:vw" and
yet the argument handler expects an argument.
When parse_optarg_string is called with a null argument, we then proceed to
crash in strncmp, not horribly friendly.
The man page describes -w as taking an argument, the long form
(--hwp-window) is correctly marked as taking a required argument, and the
code expects it.
As such, this patch simply marks the short form (-w) as requiring an
argument.
Signed-off-by: Zephaniah E. Loss-Cutler-Hull <zephaniah@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Matt Lupfer [Thu, 20 Sep 2018 14:31:44 +0000 (10:31 -0400)]
tools/power: Fix typo in man page
From context, we mean EPB (Enegry Performance Bias).
Signed-off-by: Matt Lupfer <mlupfer@ddn.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Ben Hutchings [Sun, 16 Sep 2018 15:06:10 +0000 (16:06 +0100)]
tools/power/x86: Enable compiler optimisations and Fortify by default
Compiling without optimisations is silly, especially since some
warnings depend on the optimiser. Use -O2.
Fortify adds warnings for unchecked I/O (among other things), which
seems to be a good idea for user-space code. Enable that too.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
Ben Hutchings [Sun, 16 Sep 2018 15:05:53 +0000 (16:05 +0100)]
tools/power x86_energy_perf_policy: Fix "uninitialized variable" warnings at -O2
x86_energy_perf_policy first uses __get_cpuid() to check the maximum
CPUID level and exits if it is too low. It then assumes that later
calls will succeed (which I think is architecturally guaranteed). It
also assumes that CPUID works at all (which is not guaranteed on
x86_32).
If optimisations are enabled, gcc warns about potentially
uninitialized variables. Fix this by adding an exit-on-error after
every call to __get_cpuid() instead of just checking the maximum
level.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
Linus Torvalds [Sat, 31 Aug 2019 17:27:42 +0000 (10:27 -0700)]
Merge branch 'i2c/for-current' of git://git./linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"I2C has a bunch of driver fixes and a core improvement to make the
on-going API transition more robust"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: mediatek: disable zero-length transfers for mt8183
i2c: iproc: Stop advertising support of SMBUS quick cmd
MAINTAINERS: i2c mv64xxx: Update documentation path
i2c: piix4: Fix port selection for AMD Family 16h Model 30h
i2c: designware: Synchronize IRQs when unregistering slave client
i2c: i801: Avoid memory leak in check_acpi_smo88xx_device()
i2c: make i2c_unregister_device() ERR_PTR safe
Linus Torvalds [Sat, 31 Aug 2019 16:15:25 +0000 (09:15 -0700)]
Merge tag 'trace-v5.3-rc6' of git://git./linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Small fixes and minor cleanups for tracing:
- Make exported ftrace function not static
- Fix NULL pointer dereference in reading probes as they are created
- Fix NULL pointer dereference in k/uprobe clean up path
- Various documentation fixes"
* tag 'trace-v5.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Correct kdoc formats
ftrace/x86: Remove mcount() declaration
tracing/probe: Fix null pointer dereference
tracing: Make exported ftrace_set_clr_event non-static
ftrace: Check for successful allocation of hash
ftrace: Check for empty hash and comment the race with registering probes
ftrace: Fix NULL pointer dereference in t_probe_next()
Linus Torvalds [Sat, 31 Aug 2019 16:02:36 +0000 (09:02 -0700)]
Merge tag 'riscv/for-v5.3-rc7' of git://git./linux/kernel/git/riscv/linux
Pull RISC-V fix from Paul Walmsley:
"One significant fix for 32-bit RISC-V systems:
Fix the RV32 memory map to prevent userspace from corrupting the
FIXMAP area. Without this patch, the system can crash very early
during the boot"
* tag 'riscv/for-v5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
RISC-V: Fix FIXMAP area corruption on RV32 systems
Linus Torvalds [Sat, 31 Aug 2019 15:51:48 +0000 (08:51 -0700)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
"PPC:
- Fix bug which could leave locks held in the host on return to a
guest.
x86:
- Prevent infinitely looping emulation of a failing syscall while
single stepping.
- Do not crash the host when nesting is disabled"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Don't update RIP or do single-step on faulting emulation
KVM: x86: hyper-v: don't crash on KVM_GET_SUPPORTED_HV_CPUID when kvm_intel.nested is disabled
KVM: PPC: Book3S: Fix incorrect guest-to-user-translation error handling
Linus Torvalds [Sat, 31 Aug 2019 15:31:48 +0000 (08:31 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge misc mm fixes from Andrew Morton:
"7 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: memcontrol: fix percpu vmstats and vmevents flush
mm, memcg: do not set reclaim_state on soft limit reclaim
mailmap: add aliases for Dmitry Safonov
mm/z3fold.c: fix lock/unlock imbalance in z3fold_page_isolate
mm, memcg: partially revert "mm/memcontrol.c: keep local VM counters in sync with the hierarchical ones"
mm/zsmalloc.c: fix build when CONFIG_COMPACTION=n
mm: memcontrol: flush percpu slab vmstats on kmem offlining
Jakub Kicinski [Wed, 28 Aug 2019 05:25:47 +0000 (22:25 -0700)]
tracing: Correct kdoc formats
Fix the following kdoc warnings:
kernel/trace/trace.c:1579: warning: Function parameter or member 'tr' not described in 'update_max_tr_single'
kernel/trace/trace.c:1579: warning: Function parameter or member 'tsk' not described in 'update_max_tr_single'
kernel/trace/trace.c:1579: warning: Function parameter or member 'cpu' not described in 'update_max_tr_single'
kernel/trace/trace.c:1776: warning: Function parameter or member 'type' not described in 'register_tracer'
kernel/trace/trace.c:2239: warning: Function parameter or member 'task' not described in 'tracing_record_taskinfo'
kernel/trace/trace.c:2239: warning: Function parameter or member 'flags' not described in 'tracing_record_taskinfo'
kernel/trace/trace.c:2269: warning: Function parameter or member 'prev' not described in 'tracing_record_taskinfo_sched_switch'
kernel/trace/trace.c:2269: warning: Function parameter or member 'next' not described in 'tracing_record_taskinfo_sched_switch'
kernel/trace/trace.c:2269: warning: Function parameter or member 'flags' not described in 'tracing_record_taskinfo_sched_switch'
kernel/trace/trace.c:3078: warning: Function parameter or member 'ip' not described in 'trace_vbprintk'
kernel/trace/trace.c:3078: warning: Function parameter or member 'fmt' not described in 'trace_vbprintk'
kernel/trace/trace.c:3078: warning: Function parameter or member 'args' not described in 'trace_vbprintk'
Link: http://lkml.kernel.org/r/20190828052549.2472-2-jakub.kicinski@netronome.com
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Jisheng Zhang [Mon, 26 Aug 2019 09:13:12 +0000 (09:13 +0000)]
ftrace/x86: Remove mcount() declaration
Commit
562e14f72292 ("ftrace/x86: Remove mcount support") removed the
support for using mcount, so we could remove the mcount() declaration
to clean up.
Link: http://lkml.kernel.org/r/20190826170150.10f101ba@xhacker.debian
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Xinpeng Liu [Wed, 7 Aug 2019 23:29:23 +0000 (07:29 +0800)]
tracing/probe: Fix null pointer dereference
BUG: KASAN: null-ptr-deref in trace_probe_cleanup+0x8d/0xd0
Read of size 8 at addr
0000000000000000 by task syz-executor.0/9746
trace_probe_cleanup+0x8d/0xd0
free_trace_kprobe.part.14+0x15/0x50
alloc_trace_kprobe+0x23e/0x250
Link: http://lkml.kernel.org/r/1565220563-980-1-git-send-email-danielliu861@gmail.com
Fixes:
e3dc9f898ef9c ("tracing/probe: Add trace_event_call accesses APIs")
Signed-off-by: Xinpeng Liu <danielliu861@gmail.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Denis Efremov [Thu, 4 Jul 2019 17:21:10 +0000 (20:21 +0300)]
tracing: Make exported ftrace_set_clr_event non-static
The function ftrace_set_clr_event is declared static and marked
EXPORT_SYMBOL_GPL(), which is at best an odd combination. Because the
function was decided to be a part of API, this commit removes the static
attribute and adds the declaration to the header.
Link: http://lkml.kernel.org/r/20190704172110.27041-1-efremov@linux.com
Fixes:
f45d1225adb04 ("tracing: Kernel access to Ftrace instances")
Reviewed-by: Joe Jin <joe.jin@oracle.com>
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Denis Efremov [Thu, 29 Aug 2019 16:50:24 +0000 (19:50 +0300)]
udp: Remove unlikely() from IS_ERR*() condition
"unlikely(IS_ERR_OR_NULL(x))" is excessive. IS_ERR_OR_NULL() already uses
unlikely() internally.
Signed-off-by: Denis Efremov <efremov@linux.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Joe Perches <joe@perches.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Denis Efremov [Thu, 29 Aug 2019 16:50:17 +0000 (19:50 +0300)]
net/mlx5e: Remove unlikely() from WARN*() condition
"unlikely(WARN_ON_ONCE(x))" is excessive. WARN_ON_ONCE() already uses
unlikely() internally.
Signed-off-by: Denis Efremov <efremov@linux.com>
Cc: Boris Pismenny <borisp@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Joe Perches <joe@perches.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: netdev@vger.kernel.org
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 31 Aug 2019 01:56:08 +0000 (18:56 -0700)]
Merge branch 'linus' of git://git./linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"Fix a potential crash in the ccp driver"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: ccp - Ignore unconfigured CCP device on suspend/resume
Linus Torvalds [Sat, 31 Aug 2019 01:47:15 +0000 (18:47 -0700)]
Partially revert "kfifo: fix kfifo_alloc() and kfifo_init()"
Commit
dfe2a77fd243 ("kfifo: fix kfifo_alloc() and kfifo_init()") made
the kfifo code round the number of elements up. That was good for
__kfifo_alloc(), but it's actually wrong for __kfifo_init().
The difference? __kfifo_alloc() will allocate the rounded-up number of
elements, but __kfifo_init() uses an allocation done by the caller. We
can't just say "use more elements than the caller allocated", and have
to round down.
The good news? All the normal cases will be using power-of-two arrays
anyway, and most users of kfifo's don't use kfifo_init() at all, but one
of the helper macros to declare a KFIFO that enforce the proper
power-of-two behavior. But it looks like at least ibmvscsis might be
affected.
The bad news? Will Deacon refers to an old thread and points points out
that the memory ordering in kfifo's is questionable. See
https://lore.kernel.org/lkml/
20181211034032.32338-1-yuleixzhang@tencent.com/
for more.
Fixes:
dfe2a77fd243 ("kfifo: fix kfifo_alloc() and kfifo_init()")
Reported-by: laokz <laokz@foxmail.com>
Cc: Stefani Seibold <stefani@seibold.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Greg KH <greg@kroah.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Shakeel Butt [Fri, 30 Aug 2019 23:04:53 +0000 (16:04 -0700)]
mm: memcontrol: fix percpu vmstats and vmevents flush
Instead of using raw_cpu_read() use per_cpu() to read the actual data of
the corresponding cpu otherwise we will be reading the data of the
current cpu for the number of online CPUs.
Link: http://lkml.kernel.org/r/20190829203110.129263-1-shakeelb@google.com
Fixes:
bb65f89b7d3d ("mm: memcontrol: flush percpu vmevents before releasing memcg")
Fixes:
c350a99ea2b1 ("mm: memcontrol: flush percpu vmstats before releasing memcg")
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Roman Gushchin <guro@fb.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>